Tenders of Dept Of The Navy Usa

See Attached Sources Sought Notice, N32205-ss-n321-25-022.

This Is A Combined Synopsis/solicitation For Commercial Items Prepared In Accordance With The Format In Subpart 12.6, As Supplemented With Additional Information Included In This Notice. This Announcement Constitutes The Only Solicitation; Proposals Are Being Requested And A Written Solicitation Will Not Be Issued. The Solicitation Document And Incorporated Provisions And Clauses Are Those In Effect Through Federal Acquisition Circular 2025-03 . The Provisions At 52.212-1, 52.212-3 And The Clauses At 52.212-4, 52.212-5 Apply To This Acquisition; No Addenda Are Attached. this Is An All-or-none Requirement And Partial Quotes Will Be Deemed Unresponsive And Will Not Be Evaluated. The Government Will Award On A Single Purchase Order To The Responsible Offeror Whose Offer Conforms To The Requirements As Stated In The Solicitation And Is Most Advantageous To The Government Based On The Criteria Listed In Section L And Section M Of The Solicitation. offerors Must Be Registered In Sam And All Responsible Sources May Submit A Quotation Which, If Timely Received, Will Be Considered By The Agency. Quotes Are Due No Later Thanthe Response Date In The Posting. Responses/offers Shall Be Submitted Electronically, Pdf Or Ms Word Formatto The Email Address In The Posting. any Amendment(s) Issued To This Request For Quote (rfq) Will Be Published On This Website. Therefore, It Is The Offerors Responsibility To Visit This Website Frequently For Updates On This Procurement. No Telephone Requests.

N00421-24-rfpreq-45n000a-0014 Advanced Technology Development Department Asw Research And Development Rfp

Request For Information - Sources Sought naval Air Warfare Center, Aircraft Division Lakehurst, Nj Rsd Pump introduction: this Request For Information (rfi) Is Issued Pursuant To Far 15.201(e) And In Conformance With Dfars Pgi 206.302. This Is A Request For Information/sources Sought Notice To Solicit Comments, Questions And Feedback From Industry Regarding A Planned Procurement Of A Fixed Displacement Hydraulic Pump Identified Below. Nawcad Lakehurst Is Requesting Vendor Sources With The Capability Of Supplying Said Pump. Interested Parties May Submit Technical Literature/brochures On Solutions That Meet These Material Requirements. Any Relevant Information May Also Be Submitted For Consideration To Aid In Refinement Of This Requirement. this Rfi Is Not A Request For Proposal: it Is A Market Research Tool Being Used To Determine Potential And Eligible Vendors Capable Of Providing Services Described Herein Prior To Determining The Method Of Acquisition And Issuance Of A Request For Proposal. The Government Is Not Obligated To And Will Not Pay For Any Information Received From Potential Sources As A Result Of This Notice. eligibility: the Psc For This Requirement Is 1650 (aerospace Craft Components And Accessories -aircraft Hydraulic, Vacuum, And De-icing System Components), Naics Is 333996 (fluid Power Pump And Motor Manufacturing). All Interested Businesses Are Encouraged To Respond. submittal Information: it Is Requested That Interested Businesses Submit To The Contracting Office A Brief Capabilities Statement Package Demonstrating Ability To Meet The Requirements Outlined In Description. Responses Must Include 0579-rsd Pump In Subject. This Documentation Must Address, At A Minimum, The Following: company Contact Information To Include: Company Name, Company Address, Cage Code, Company Business Size, And Point-of-contact (poc) Name, Phone Number, Fax Number, And E-mail Address. company Profile To Include: Number Of Employees And Duns Number; Statement Regarding Capability. if You Are A Small Business, Provide An Explanation Of Your Company's Ability To Perform At Least 50% Of The Tasking Described In The Specifications. the Capability Statement Package Shall Be Sent Via Email To Air- 2.5.2.5.2 Navair Lakehurst Contracts, Zaib Nageeb, Zaib.nageeb.civ@us.navy.mil. Submissions Must Be Received At The Office Cited No Later Than 5:30 P.m. Eastern Standard Time On 19 September 2024.  description: nawcad Lakehurst Is Seeking A Fixed Displacement Hydraulic Pump With The Following Specifications And Characteristics: operating Speed: 1200 Rpm (nominal) rated Delivery At 1200 Rpm: 0.5 Usgpm (minimum) operating Pressure: 3000 Psig maximum Recommended Pressure: 3400 Psig direct Couple Driven By Ac Motor pump Shall Be Compatible With Hydraulic Fluid Mil-prf-83282 overall Maximum Envelope Dimension: height: 4 In width: 4 In length: 4.5 In other Relevant Specification: coupled To 208 Vac 400hz Motor synchronous Speed- 1200rpm full Load Rating- 1170 Rpm, 1.45hp, 5.5 Amps Intermittent Duty the Following Specifications Are Preferred But Not Required: shaft Spline (motor Attachment) Per Sae Ansi B92.1- 1996 pressure Angle: 30 Deg spline Pitch: 24/48 number Of Teeth: 11 mounting Face Per And10260 Type X reliability: Mtbf Of 1.7 X 10 Hours ports Per And10050-6 how To Respond: all Interested Parties Must Submit Written Responses, Preferably Via Electronic Mail Within Fifteen (15) Days After Release Of This Rfi With Product Information That Meets All Or A Subset Of The Aforementioned Attributes. Please Submit Your Response To This Rfi Via E-mail No Later Than 19 September 2024, 5:30 Pm Edt To Contract Specialist, Zaib Nageeb At Zaib.nageeb.civ@us.navy.mil. the Navy Does Not Intend To Award A Contract On The Basis Of This Request Or Otherwise Pay For The Information Solicited. While The Navy Intends To Use This Information For Future Acquisition Planning Purposes, It Will Not Release Any Information About Your Approach That Might In Any Way Compromise Your Competitive Posture Or Proprietary Information. The Navy Will Not Use Any Information Provided To Level Your Company’s Approach Relative To Another Competitor. All Information Received In Response To This Rfi That Is Marked Proprietary Will Be Handled Accordingly. The Navy Will Not Be Liable For Or Suffer Any Consequential Damages For Any Proprietary Information Not Properly Identified. Proprietary Information Will Be Safeguarded In Accordance With The Applicable Navy Regulations. Responses To This Rfi Will Not Be Returned. Respondents Will Not Be Notified Of The Result Of The Review. Failure To Respond To This Rfi Does Not Preclude Participation In Any Future Associated Rfp/rfq That May Be Issued. Information Provided In No Way Binds The Navy To Solicit Or Award A Contract. If A Solicitation Is Released, It Will Be Synopsized On The System For Award Management (sam) Website: Www.sam.gov. It Is The Potential Vendor's Responsibility To Monitor This Site For The Release Of Any Follow-on Information.

Sources Sought Notice - P273 Bulk Fuel Storage Tank Hydrant System, Naval Air Station - Whidbey Island (naswi), Wa Construction Project For Building And/or Heavy (nonbuilding/ Residential) Requirements

Subject: Bulk Laundry Services this Is A Combined Synopsis/solicitation For Commercial Items Prepared In Accordance With The Format In Far Subpart 12.6, As Supplemented With Additional Information Included In This Notice. This Announcement Constitutes The Only Solicitation; Quotes Are Being Requested And A Written Solicitation Will Not Be Issued. This Procurement Is Under Full And Open Competition Under Naics Code 812320 Size Standard Of $8.0m. An Offeror’s Submission Of A Quote Does Not Constitute A Contract Or Authorize Work To Begin. This Document Is Not Legally Binding And Does Not Commit The Us Government In Any Way. this Solicitation Document And Incorporated Provisions And Clauses Are Those In Effect Through Federal Acquisition Circular 2025-02 And Defense Federal Acquisition Regulations Supplement Publication Notice (dpn) 20241218. in Accordance With Far 12.102(c), When A Policy In Another Part Is Inconsistent With Far Part 12, Part 12 Shall Take precedence. **questions And Answers Posted On 10 Jan 2025** **solicitation Period Extended (posted 20 Jan 2025)**

Uss Russell (ddg-59) Hull Preservation

Contact Information|4|n9743f|feb|717-605-7237|karen.m.barlet.civ@us.navy.mil| item Unique Identification And Valuation (jan 2023)|19|||||||||||||||||||| inspection Of Supplies--fixed-price (aug 1996)|2||| special Shipping And Marking Instructions|6|x|||x||| general Information-fob-destination|1|b| wide Area Workflow Payment Instructions (jan 2023)|16|invoice And Receiving Report (combo)|n/a|tbd|n00104|tbd|tbd|see Schedule|tbd|n/a|n/a|tbd|n/a|n/a|n/a|n/a|navsupwawf.wss.ftc@navy.mil| note For Contractor/administrative Contracting Officer|3|||| navy Use Of Abilityone Support Contractor - Release Of Offeror Information (3-18))|1|| notice Of Total Small Business Set-aside (oct 2020)(deviation 2020-o0008)|1|| alternate A, Annual Representations And Certifications (oct 2024)|13|||||||||||||| annual Representations And Certifications (may 2024)|13|332722|600|||||||||||| notice Of Priority Rating For National Defense, Emergency Perpardeness, And Enrgy Progam Use (april 2008))|2||x| government Source Inspection Per Far 52.246-2 Is Required. delivery 90 Days. all Contractual Documents (i.e. Contracts, Purchase Orders, Task Orders,delivery Orders And Modifications) Related To The Instant Procurement Areconsidered To Be "issued" By The Government When Copies Are Either Depositedin The Mail, Transmitted By Facsimile, Or sent By Other Electronic Commercemethods, Such As Email. The Government's Acceptance Of The Contractor'sproposal Constitutes Bilateral Agreement To "issue" Contractual Documents Asdetailed Herein. \ 1. Scope 1.1 This Contract/purchase Order Contains The Requirements For Manufacture Of The Nut,self-locking,he . 2. Applicable Documents - Not Applicable 3. Requirements 3.1 Manufacturing And Design - The Nut,self-locking,he Furnished Under This Contract/purchase Order Shall Meet The Material And Physical Requirements As Specified ;mil-spec Part Number: Ms21044n16 Cage Code (80205) Nut, Self-locking, Hex; . 3.2 Marking - Unless Marking Requirements Are Specified By A Document Or Drawing Cited In This Solicitation All Items Delivered Under This Contract/purchase Order Shall Be Marked And Identified In Accordance With The Applicable Military Standards And specifications As Follows: Mechanical Parts, Assemblies And Equipments - Mil-std-130 Electrical And Electronic Parts - Mil-std-1285, Method 1. Electrical And Electronic Parts And Assemblies Not Covered By Mil-std-1285-use Mil-std-130. Electronic Equipment - Mil-std-454 Requirement Number 67. Electrical Equipment - Mil-p-15024/5 (ships) 3.3 Configuration Control - Mil-std-973 Entitled "configuration Management", Paragraph 5.4.8, Configuration Control (short Form Procedure), Is Hereby Incorporated. The Contractor Shall Submit All Engineering Change Proposals In Accordance With Mil-std-973, paragraph 5.4.8.2 And Appendix D. Requests For Deviations Shall Be Processed In Accordance With Mil-std-973, Paragraph 5.4.8.3 And Appendix E. Requests For Waivers Shall Be Processed In Accordance With Mil-std-973, Paragraph 5.4.8.4 And Appendix E. (original and Two Copies Shall Be Submitted To Contracting Officer, Navicp-mech, P. O. Box 2020, Mechanicsburg Pa. 17055-0788.) 4. Quality Assurance 4.1 Responsibility For Inspection - Unless Otherwise Specified In The Contract/purchase Order, The Contractor Is Responsible For The Performance Of All Inspection Requirements As Specified Herein. Except As Otherwise Specified In The Contract/purchase Order, the Contractor May Use His Own Or Any Other Facilities Suitable For The Performance Of The Inspection Requirements Specified Herein, Unless Disapproved By The Government. The Government Reserves The Right To Perform Any Of The Inspections Set Forth In The specification Where Such Inspections Are Deemed Necessary To Assure Supplies And Services Conform To Prescribed Requirements. 4.2 Responsibility For Compliance - All Items Must Meet All Requirements Of This Contract/purchase Order. The Inspection Set Forth In This Specification Shall Become A Part Of The Contractor's Overall Inspection System Or Quality Program. The Absence Of Any inspection Requirements Shall Not Relieve The Contractor Of The Responsibility Of Assuring That All Products Or Supplies Submitted To The Government For Acceptance Comply With All Requirements Of The Contract/purchase Order. Sampling In Quality Conformance does Not Authorize Submission Of Known Defective Material, Either Indicated Or Actual, Not Does It Commit The Government To Acceptance Of Defective Material. 4.3 Records - Records Of All Inspection Work By The Contractor Shall Be Kept Complete And Available To The Government During The Performance Of Contract/purchase Order And For A Period Of 365 Calendar Days After Final Delivery Of Supplies. 5. Packaging 5.1 Preservation, Packaging, Packing And Marking - Preservation, Packaging, Packing And Marking Shall Be In Accordance With The Contract/purchase Order Schedule And As Specified Below. mil-std 2073 Packaging Applies As Found Elsewhere In The Schedule 6. Notes 6.1 Ordering Information For Document References - The Department Of Defense Single Stock Point (dodssp), Website Http://www.dsp.dla.mil/, Provides Product Information For The Department Of Defense Index Of Specifications And Standards (dodiss) (i.e.military/federal Specifications And Standards), Data Item Descriptions (dids), And Other Dodssp Products. a. Availability Of Cancelled Documents - The Dodssp Offers Cancelled Documents That Are Required By Private Industry In Fulfillment Of Contractual Obligations In Paper Format. Documents Can Be Requested By Phoning The Subscription Services Desk. b. Commercial Specifications, Standards, And Descriptions - These Specifications, Standards And Descriptions Are Not Available From Government Sources. They May Be Obtained From The Publishers Of The Applicable Societies. C. Ordnance Standards (os), Weapons Specifications (ws), And Navord Ostd 600 Pages - These Type Publications May Be Obtained By Submitting A Request To: Commander, Indian Head Division, Naval Surface Warfare Center Code 8410p, 101 Strauss Avenue Indian Head, Md 20640-5035 d. On Post-award Actions, Requests For "official Use Only" And "noforn" (not Releasable To Foreign Nationals) Documents Must Identify The Government Contract Number, And Must Be Submitted Via The Cognizant Defense Contract Management Command (dcmc) For certification Of Need For The Document. On Pre-award Actions Such Requests Must Be Submitted To The Pco For Certification Of Need For The Document. e. Noforn Military Specifications And Standards (including Amendments, Change Notices And Supplements, But Not Interim Changes) To Be Ordered From: Contracting Officer Navicp-mech Code 87321 5450 Carlisle Pike P.o. Box 2020 Mechanicsburg, Pa. 17055-0788 f. Nuclear Reactor Publications Assigned Navsea Documents And Identification Numbers (i.e. Navsea Welding Standard, Navsea 250-1500-1) Are To Be Ordered From: Commanding Officer Navicp-mech Code 009 5450 Carlisle Pike P.o. Box 2020 Mechanicsburg, Pa. 17055-0788 g. Technical Manuals Assigned Navsea Identification Numbers (i.e. Navsea Welding And Brazing Procedure, Navsea S9074-aq-gib-010/248) Are To Be Ordered From: Naval Inventory Control Point Code 1 Support Branch 700 Robbins Avenue Phildelphia, Pa. 19111-5094 h. Interim Changes And Classified Specifications Shall Be Obtained By Submitting A Request On Dd Form 1425 To Navicp-mech. 6.2 Commercial Brand Name Description - This Contract/purchase Order Covers A Commercial Brand Name Description. If An Alternate Item Is Proposed, Submit A Complete Technical Description Of The Item With Your Proposal For The Government's Review To Determine if The Item Meets The Minimum Requirements Of This Contract/purchase Order. mil-spec Part Number: Ms21044n16 Cage Code (80205) Nut, Self-locking, Hex

This Solicitation Notice For Non-commercial Products Under Simplified Acquisition Procedures Prepared In Accordance With The Format In Far Subpart 13.105, As Supplemented With Additional Information Included In This Notice. the Portsmouth Naval Shipyard Will Seek Responses From Sources Capable Of Providing The Following: 0001 Boa Item 7027aa nsn: 1h 5310-01-589-1143 X2 30 Ea. Nut, Hex, Tyiii, Heavy In Accordance With The Specifications For Boa Item 7027aa Listed In The Portsmouth Naval Shipyard C. R. Gilbert / E. F. Dickson Fastener Program Manual, Dated 2021. 0002 Data Requirements Data Requirements For Item 0001: data Item A001 (material Certification) ***all Manufacturing And Data Requirements Shall Be In Full Accordance With All Of The Specifications And Data Requirements For Boa Item 7027aa Listed In The Portsmouth Naval Shipyard C. R. Gilbert / E. F. Dickson Fastener Program Manual (aka The Boa Book). Copies Of The Boa Book (which Include Required Specs And/or Data Requirements) May Be Requested From Lauren Leduc Who Can Be Reached By Email Lauren.w.leduc.civ@us.navy.mil With An Active Dd2345 Form. see The Attached N3904025q4046 Rfq Solicitation For Additional Details Including Submission Instructions, Evaluation Criteria, And Additional Provisions And Clauses Applicable To This Procurement.

Nsn 7r-1680-014458278-vh, Iaw Ref Nr 42315-17, Qty 3 Ea, Delivery Fob Origin. This Part Must Be Acquired From/repaired By A Source(s)specified On A Source Control Or Selected Item Drawing As Defined By Thecurrent Version Of Dod-std-100. Suitable Technical Data, Government Data Rights, Or Manufacturing/repair Knowledge Are Not Available To Permit Acquisition From/repair By Other Sources, Nor Qualification Testing Of Another Part, Nor Use Of A Second Source Part In The Intended Application. Although, By Dod-std-100 Definition, Altered And Selected Items Shall Have An Adequate Technical Data Package, Data Review Discloses That Required Data Or Data Rights Are Not In Government Possession And Cannot Be Economically Obtained. The Subject Item Requires Government Source Approval Prior To Contract Award, As The Item Is Flight Critical And/or The Technical Data Available Has Not Been Determined Adequate To Support Acquisition Via Full And Open Competition. Only The Source(s) Previously Approved By The Government For This Item Have Been Solicited. The Time Required For Approval Of A New Source Is Normally Such That An Award Cannot Be Delayed Pending Approval Of A New Source. If You Are Not An Approved Source You Must Submit, Together With Your Proposal, The Information Detailed In One Of The Navsup Weapon Systems Support (navsup Wss) Source Approval Information Brochures Listed Below. Spares: Https://www.navsup.navy.mil/navsup-enterprise/navsup-weapon-systems-sup Port/business-opps/ Repair: Https://www.navsup.navy.mil/navsup-enterprise/navsup -weapon-systems-support/business-opps/ Technical Data Required To Be Submitted Based On Your Company's Experience In Production Of The Same Or Similar Item, Or If This Is An Item You Have Never Made. If Your Request For Source Approval Is Currently Being Evaluated At Navsup Wss Submit With Your Offer A Copy Of The Cover Letter Which Forwarded Your Request For Source Approval. Offers Received Which Fail To Provide All Data Required By The Source Approval Brochure Or Document Previous Submission Of All Data Required By The Source Approval Brochure Will Not Be Considered For Award Under This Solicitation. Please Note, If Evaluation Of A Source Approval Request Submitted Hereunder Cannot Be Processed In Time And/or Approval Requirements Preclude The Ability To Obtain Subject Items In Time To Meet Government Requirements, Award Of The Subject Requirement May Continue Based On Fleet Support Needs. The Navsup Wss Commercial Item Identification Brochure Is Now Available At: "https://www.navsup.navy.mil/navsup-enterprise/navsup-weapon-systems-support/bus Iness-opps/" Interested Parties May Obtain Copies Of Military And Federal Specificationsand Standards, Qualified Products Lists (qpls), Qualified Product Databases(qpds), Military Handbooks, And Other Standardized Documents From The Dodsingle Stock Point (dodssp) At Document Automation And Production Service(daps) In Philadelphia, Pa. Note: Patterns, Drawings, Deviation Lists, Purchase Descriptions, Etc. Are Not Stocked At Dodssp. Most Documents Are Available In Adobe Pdf Format From Assist-online At: Http://quicksearch.dla.mil/. Users May Use Assist-quick Search To Search For And Download Available Documents Directly Using Standard Browser Software. Documents That Are Not Available For Downloading From Assist-quick Search Can Be Ordered From The Dodssp Website Using The Assist Shopping Wizard After Obtaining A Dodssp Customer Account By Following The Registration Procedures. Users Who Do Not Have Access To The Internet May Contact The Dodssp Assisthelp Desk At 215-697-2667 Or 215-697-2179 (dsn: 442-2667), Or Mail Their Request To Dladocument Services, Bldg. 4/d, 700 Robbins Avenue, Philadelphia Pa 19111-5094. Award Will Be Made Only If The Offeror, The Product/service, Or The Manufacturer Meets The Qualification Requirement(s) At Time Of Award, In Accordance With Far Clause 52.209-1. The Solicitation Identifies The Office Where Additional Information Can Be Obtained Concerning Qualification Requirements And Is Cited In Each Individual Solicitation. One Or More Of The Items Under This Acquisition Is Subject To: Free Trade Agreements, If Dfars Clause 252.225-7036 Buy American Act--free Trade Agreements--balance Of Payments Program, Is Included In Thesolicitation. The World Trade Organization Government Procurement Agreement And Free Trade Agreements, If Dfars Clause 252.225-7021 Trade Agreements, Is Included In The Solicitation.