Cable Tenders

Details: The subject of the performance of the public contract is work consisting in the replacement, addition and installation of existing lighting for new LED lighting. On the subject part of Vo, the existing lighting will be replaced and supplemented with new LED lighting, except for the existing light points, which are equipped with LED lamps and ground lamps, which are used to illuminate monuments. The power supply of the light places is carried out by cable and overhead lines. When replacing the lamps, the power supply of the individual lamps will first be disconnected in their terminal blocks from the Vo distribution. After that, the dismantling of the existing lights from the booms will be carried out. The New Led Lamp Will Be Powered From The New Power Cable Cyky-j 3x1.5mm2. All Luminaires On Concrete Poles From Over Distribution Need To Upgrade Drop Cable, Clamps And Hooks. The lamp must be equipped with a fuse. Subsequently, the power cable will be connected to the Vo distribution in the terminal box. Depending on the technical condition (age, functionality, wear), this terminal block can be replaced with a new one. Replacement of Luminaires Will Take Place on a Concrete or Steel Mast. After the completion of the replacement of all luminaires according to the project, an audit report, a protocol on the measurement of illuminance, a protocol on the ecological disposal of dismantled material and the passporting of public lighting will be prepared. As part of the project, Vo switchboards will be retrofitted with type C auxiliary circuit breakers in order to prevent the unwanted tripping of overcurrent protections due to surge currents from the lighting power sources.

Details: Description Qty. Description 1 Lot A. General Conditions Complete All Works For The Project “repair And Renovation Of The Office Of Investigation Division, Ciis” Including Supply Of All Materials, Equipment, And Systems, As Well As The Performance Of All Necessary Labor And Processes, In Accordance With The Plans, Specifications, The Bidding Documents, The Terms Of References And Other Related Contract Documents. The Contractor Is Not Limited To The Scope Of Works Listed. He Should Verify All Plans And Actual Conditions For The Necessity Of Work. If The Actual Situation Calls For Demolition, Removal, And Relocation He Shall Include Such And All Concomitant Works To Finish As Part Of The Scope Of Work. Any Discrepancies Found Between The Drawings And Specifications And The Site Conditions Or Any Errors Or Omissions In The Drawings Or Specifications Should Be Clarified With The Architect/consultant/engineer. Should The Contractor Fail To Verify Or Clarify Discrepancies, Errors, Conflicts, Or Omissions In The Drawings And Specifications, It Shall Be Deemed That The Contractor Has Included In The Preparation Of His Bid The Necessary Works, Materials, Or Items Needed To Satisfy The General Scope Of Works. During The Renovation Phase To Completion, The Contractor Shall Deploy A Licensed Civil Engineer And Architect To Supervise And Direct The Work Of His Staff In Carrying Out The Activities Required To Ensure That The Specified Works Are Constructed In Full Accordance With The Approved Contract Documents And Shall Be Responsible For All Aspects Of The Project. B. Scope 1. Mobilization A. Preparation Of Logistics Of Contractor’s Equipment; B. Setting Up Of Temporary Facilities Within The Site; C. Setting Up Of Necessary Water And Power Lines Required For The Project; D. Setting Up Of Temporary Fence Enclosure; E. Installation Of Project Details Tarpaulin Signage (30x20”) With Frame Located At The Front Of The Project Site Location; And F. Inventory Of Items To Turn Over. 2. Demobilization A. Site Demolition And Dismantling Of Existing Concrete Walls, Dry Walls, Ceiling And Electrical Wirings; B. Hauling Of Debris And Materials From The Project Site To The Appropriate Disposal Area; And C. Within 10 Calendar Days Upon Completion Of The Project, The Contractor Shall Submit One (1) Complete Set Of As-built Plans (printed In Blueprinted Paper) Duly Signed And Sealed By The Contractor, Drawn In 24” X 36” Drawing Sheets. 3. Carpentry Works A. Supply And Installation Of 9mm Thk. Ficem Board With Complete Standard Metal Furring Support On All Ceilings As Shown In The Plans And Bill Of Quantities (boq); B. Supply And Installation Of 9mm Thk. Ficem Board With Complete Standard Metal Stud Support On All Drywalls As Indicated In The Plans And Boq; C. Installation Of Fluted Pvc Wall Panel Backdrop As Shown In The Perspective And Boq; And D. Fabrication Of Built-in Cabinets, Shelves And Reception Table As Indicated In The Plans, Perspective And Boq. 4. Painting Works A. All Surface Defects Shall Be Repaired And All Surfaces Shall Be Scraped To Remove Deteriorated Coatings And Other Deleterious Materials. Surfaces Shall Then Be Cleaned With Steam Or With A Commercial Cleaner To Remove All Grease, Oil, And Chemical Residues; B. Prior To Painting Works, Surfaces On Masonry, Wood, And Metal Must Be Free From Any Dirt, Grease, Old Paint, And Rust, Eliminate Loose Or Peeling Paint, And Get Rid Of Rust Deposits Before Applying Primer/putty And Paint Finish; And C. Contractor Shall Ensure That All Delivered Painting Materials To The Work Site Shall Be In Original Containers With Seals And Labels Intact. Containers Shall Not Be Opened Until After They Have Been Inspected By The End-user Or Its Duly Authorized Representative. 5. Finished Hardware A. Supply And Installation Of Tempered Glass Door For The Main Door As Indicated In The Plans And Boq; B. Supply And Installation Of Solid Panel Doors Including Door Jambs And Accessories As Indicated In The Plans And Boq; C. Supply And Installation Of Hidden Door With Pvc Fluted Wall Panel Including Complete Accessories As Indicated In The Plans And Boq; And D. Supply And Installation Of Pvc Doors For Comfort Rooms With Complete Accessories As Specified In The Plans And Boq. 6. Floor And Tiling Works Supply And Installation Of 60cm X 60cm Floor Tiles Including Wall Tiles For Comfort Rooms As Specified In The Plans And Boq. 7. Plumbing Works Replacement Of Water Closets, Wall-hung Lavatories, Urinal, Pipes And Fittings With Complete Accessories As Indicated In The Plans And Boq. 8. Electrical Works A. Supply And Installation Of All Lighting Fixtures As Shown On The Reflected Ceiling Plan (rcp) Or As Specified By The Architect And/or End-user’s Representative; B. Supply And Installation Of Wiring Devices, Switches, Outlets, And Accessories As Shown In The Plans And Boq; And C. Supply And Installation Of Wiring Cables And Roughing-ins As Per Plans And Boq. 9. Concrete And Masonry Works Provision Of Concrete Walls For The Interview Room As Shown In The Plans And Boq. 10. Others Supply And Installation Of 2-pc. 700 Mm Diameter Boc Seals As Indicated In The Plans And Boq. 11. Permits, Licenses, And Taxes A. The Contractor Shall Secure And Pay All Permits, Fees, Licenses, Taxes, Etc. Necessary For The Execution Of The General Construction Works For The Project. B. The Contractor Shall Prepare The Complete Contract Documents Consisting Of Detailed Designs And Construction Drawings (architectural, Electrical, Structural, Mechanical, Plumbing/sanitary, Electronic And Communication Layout) In Accordance With The Municipal Engineering Office For The Building Permit Purposes; And C. The Contractor Shall Prepare A Weekly Progress Report Which Shall Include An Overall Progress Chart Based On Actual Physical Accomplishment Of Construction Work And A Progress Chart Based On Actual Value Of Accomplished Construction Work, Among Others. 12. Certification A. The Contractor Must Possess At Least A Pcab License Category C&d, Size Range Small B; B. The Contractor Shall Submit A Certificate Of Satisfactory Performance Issued By The Bureau Of Customs (boc) (for Entities With Previous/ongoing Contract/s With The Boc); In The Absence Of Contract/s With Boc, From Any Other Office/agency; And C. The Contractor Shall Submit An International Organization For Standardization (iso 9001:2015) Certificate In Construction And Contracting Issued By An Iso Certifying Body. 13. Terms Of Payment The Billing Schedule Specified In The Table Below Shall Be Followed By The Contractor: Order Of Billing Project Accomplishment Percentage First (1st) Billing At Least 50% Of The Work Has Been Accomplished Second (2nd) Billing At Least 80% Of The Work Has Been Accomplished Final Billing 100% Accomplished C. Specifications All Drawings, Whether Small Scale Or Detailed Drawings, Are Intended To Work In Unison With The Specifications And To Form Part Thereof, When Figures Are Given, They Are To Be Followed In Preference To Measurement By Scale. Anything Shown In The Drawings But Not Mentioned In The Specifications (or Vice-versa) Or Anything Not Expressively Set Forth In Either (but Which Is Reasonably Implied) Shall Be Furnished And Installed As Thought Specifically Shown In Mentioned Both. 1. Pre-construction Phase Guidelines A. A Joint Site Inventory Must Be Conducted And Signed By The Contractor, Gsd, And End-user; B. The Contractor Must Submit To Gsd His Program Evaluation Review Technique (pert) Chart/critical Path Method (cpm) Chart In Gantt Chart Form Before The Start Of The Project; C. The Contractor Must Submit To Gsd The List Of Manpower That Shall Be Utilized For The Project Along With Their Respective Designations/roles And Corresponding Qualifications. The Most Notable Figure For The Project Must Be The Project Manager, Preferably An Architect Or Engineer; And D. The Minimum Work Experience Requirements For Key Personnel Are The Following: Key Personnel Requirement Relevant Experience Project-in-charge Bachelor Of Science In Architecture/bachelor Of Science In Civil Engineer (licensed Civil Engineer/ Licensed Architect) And Building Construction Experience Five (5) Years Registered Electrical Engineer Registered Electrical Engineer And Building Construction Experience Five (5) Years Master Plumber Registered Master Plumber And Building Construction Experience Five (5) Years Safety Officer Building Construction Experience, National Certification Level Ii And Construction Occupational Safety And Health (cosh) Certificate Five (5) Years Foreman Building Construction Experience Five (5) Years Carpenter Building Construction Experience Five (5) Years Welder Building Construction Experience And National Certification Level Ii Five (5) Years Plumber Building Construction Experience And National Certification Level Ii Five (5) Years Electrician Building Wiring Installation Experience And National Certification Level Ii Five (5) Years Painter Building Construction Experience Five (5) Years Mason Building Construction Experience Five (5) Years Tile Setter Building Construction Experience Five (5) Years Laborer Building Construction Experience Three (3) Years Warehouseman Building Construction Experience Three (3) Years E. The Minimum Major Equipment Requirements Are The Following: Equipment/tools Number Of Unit/s 1 4x2 Mini Dump Truck (4 Cubic Meter Capacity) 1 Lot/ As Necessary 2 6-wheeler Elf Truck (18ft Length) 1 Lot/ As Necessary 3 One Bagger Concrete Mixer 1 Unit 4 Chipping Gun 1 Unit 5 Jackhammer 1 Unit 6 Rotary Hammer Drill 2 Units 7 Electric Drill 2 Units 8 Cut Off Machine 1 Unit 9 Electric Jig Saw 1 Unit 10 Circular Saw 1 Unit 11 Table Saw 1 Unit 12 Angle Grinder 2 Units 13 300a Welding Machine 2 Units 14 Megger Test Equipment 1 Unit 15 Multi-tester Equipment 1 Unit 16 Self-levelling Laser 2 Units 17 Nail Gun 1 Unit 18 Paint Sprayer 2 Units 19 Air Compressor 2 Units 20 Pipe Fusion Welding Machine 1 Unit 21 Tile Cutter Machine 1 Unit 22 Vacuum Cleaner 2 Units 23 Electric Sander 1 Unit 24 Wood Router 1 Unit 25 Pressure Washer 1 Unit 26 Construction Ladder 1 Lot 27 Scaffolding And Accessories 1 Lot 28 Personal Protective Equipment (ppe) 1 Lot 2. Implementation Phase Guidelines A. The Contractor Must Submit Weekly Progress Reports As Mentioned In Item B.11.c Of This Document Including Photo Documentation And Weather Updates To Gsd; B. The Contractor Must Submit Weekly Their Daily List Of Manpower; C. The Project Manager, Who Must Be A Technical Professional, Must Be Present At The Project Site At All Times To Properly Monitor/oversee The Project As Technical Representative Of The Contractor’s Side; D. Boc, Thru Its Technical Inspection And Acceptance Committee (tiac) For Civil Works, Reserves Its Right To Conduct Monitoring Inspections, Aside From The Inspections For Billing Purposes. The Project Manager Must Always Be Present, Especially During Inspections For Billing Purposes, To Ensure Proper Communication Instead Of Relying On The Foreman Or Laborers Only; E. The Approved Floor Plan And Perspective Drawings Must Be Posted On A Wall Or Board So That They Are Readily Available And Visible Whenever Necessary; F. Materials To Be Used In The Construction/renovation Must Follow Those Specified In This Document (scope Of Work), The Drawings, And/or The Boq. The Contractor Must First Secure Proper Approval Of Materials To Be Installed Via A Written Document Duly Approved By Both The End-user And Gsd. Any Change In Materials Must Also Have Proper Indorsement Thereafter. G. All Testings/activities (e.g., Waterproofing Test, Leak Test, Slump Test, Continuity Test, Insulation Resistance Test, Earthing Test, Pest Control Chemical Certificate, Etc.) Conducted By The Contractor Must Be Done With The Presence Of A Gsd Engineer/architect. Corresponding Reports Must Be Submitted To Gsd For Documentation And Validation Within Three (3) Calendar Days Upon Completion Of The Said Testing/activity; And H. Punchlisting Shall Be Conducted Upon 95.00% Completion As Ascertained By The Tiac. 3. Carpentry Works All Wood Shall Be Treated With Colorless Anti-termite Wood Preservatives. A. Ceiling Ceiling Works Shall Utilize 9mm Ficem Board With Complete Standard Metal Furring Supports. B. Wall Drywall Partition Use 9mm Thk. Ficem Board With Complete Standard Metal Studs Supports. 4. Tiling Works Tiles And Their Accessories Must Be Free From Defects That Affect Their Quality, Appearance, And Strength. All Tiles Shall Be Set To Correct Grades And Levels True To Lines, Laid Even. Submit Material For Approval. Use 60 X 60 Cm Floor And Wall Tiles In All Areas, Including The Wall Tiles For The Comfort Rooms. Use Heavy-duty Tile Adhesive And Tile Grout Joint Filler. Use T-trim/threshold Between Two Different Tile Materials. 5. Painting Application Of Plastered Paint Finish On All Interior And Exterior Walls/partitions, Ceiling, And Concrete Surfaces Within The Scope Of The Interior And Exterior Renovation Works Unless Otherwise Indicated In The Plans And Specifications. A. All Paint And Accessories, Materials Incorporated In Or Forming A Part Thereof Shall Be Subject To The Approval And Selection Of Color, Tint, Finish, Or Shade By The Architect; B. Painting Of All Surfaces, Except Otherwise Specified Shall Be (3) Coats Work, One Primer And Two Finish Coats; C. All Paint Materials Shall Meet The Requirements Of Paint Materials Under Class A; D. All Surfaces To Be Painted Shall Be Examined Carefully Before Beginning Any Painting Work, And Other Trade Works Installed In Workmanship Condition To Receive Paint Or Ant Particular Finish; E. All Paint Materials Shall Meet The Requirements Of The Specifications Set By Gsd And Shall Be Delivered On The Job In The Original Container, With Labels Intact And Seal Unbroken. F. Concrete Surfaces; Latex Paint Shall Be Used, And Preparation And Application Must Be According To The Manufacturer’s Instructions. G. Drywalls; Latex Paint Shall Be Used, And Preparation And Application Must Be According To The Manufacturer’s Instructions. Use Spray Paint For Cubicle Partition Only; H. Wooden And Metal Surfaces; Automotive Lacquer Paint Shall Be Used, And Preparation And Application Must Be According To The Manufacturer’s Instructions. Use Spray Paints; And I. Color Pigments Shall Be Used To Produce The Exact Shades Of Paint, Which Shall Conform To The Approved Color Scheme. 6. Electrical Works A. Quality Assurance - All Materials To Be Used Shall Be New And Shall Conform With The Reference Codes And Standards. Use Of Materials Shall Be Further Be Governed By Other Requirements, Impose On Other Sections Of These Specifications. Materials Shall Be Subjected To The Necessary Tests For Their Suitability Where Required; B. Alternate Materials - Use Of Any Material, Not Specified In These Specifications May Be Allowed Provided Such Alternate Has Been Approved By The Agency In Accordance With Generally Accepted Standards; C. Identification Of Materials - Each Length Of Pipe, Fitting, Box, Fixture, And Device Used In The Electrical System Shall Have Cast, Stamped Or Indelibly Marked On It The Manufacturer's Trademark Or Name, The Weight, Type And Classes Or Product When So Required By The Standards Mentioned Above; D. Wires And Cables; I. All Wires Shall Be Copper, Soft-drawn And Annealed, Shall Be Of 99% Conductivity, Shall Be Smooth And True And Of The Cylindrical Form And Shall Be Within +/-1% Variation Of The Actual Size Called For. Ii. Wires And Cables Shall Be Plastic Insulated For 600 Volts Working Pressure, Type Thermoplastic High Heat-resistant Nylon-coated (thhn) Unless Otherwise Noted. Iii. All Wires And Cables Shall Be Color Coded, Color-coding Of Wires Are As Follows: (a) Line 1 – Red (b) Line 2 – Yellow (c) Line 3 – Blue Iv. Minimum Size Of Branch Circuit Wire Shall Be 3.5 Mm2 Thhn For Power And Lighting System With 3.5mm2 Thhn Minimum Ground Wire. V. Wires 3.5 Mm2 And Bigger Shall Be Stranded. E. Switches; And I. Switches Shall Be Flush Mounted And Rated At 15 Amperes (amps), 250 Volts, One Way, Three-way As Required. Ii. Switches Shall Be Quiet Type, Spring Loaded, And The Cover Plates Shall Be Subject To The Approval Of The Architect And The Engineer. F. Receptacles I. Receptacles Shall Be Duplex, Flush Mounted And Rated At 10 Amps., 250 Volts, Parallel Or Tandem Slots With Grounding Slots As Required. All 110 Volts Receptacle Outlets Shall Be Rated 15 Amps, 120 Volts. 220 Volts Receptacle Outlets Shall Be Distinct From The 110 Volts Receptacle Outlets In Terms Of Configurations And Shall Be Provided With Markings. Ii. Cover Plates Shall Be Subject To The Approval Of The Architect And The Engineer. Stainless Steel Cover Plate Shall Be Required On All Wet Or Damped Area. Iii. All Receptacle Outlets With Ground-fault Circuit Interrupters (gfci) Shall Be Rated For 250 Volts Application With A Sensitivity Setting Of 300 Milliamps. 7. Plumbing Works A. All Works, Comply With The Requirements And Provisions Of The National Plumbing Code Of The Philippines; B. All Fixtures Shall Be Separately Trapped. The Traps Shall Be Placed As Near As Possible To The Fixtures; And C. No Fixtures Shall Be Double-trapped. Interested Suppliers Are Required To Submit Original/certified True Copy Of The Following: 1) Valid And Current Mayor’s Permit, (in Case Of Expired Mp/bp, Submit Copy Of Recently Expired Permit And Official Receipt As Proof Of Renewal), 2) Dti/sec Registration (for Partnerships/corporations, Attach General Information Sheet & Articles Of Incorporation), 3) Philgeps Registration Certificate, 4) Original Duly Signed Omnibus Sworn Statement (oss) And Original Notarized Secretary’s Certificate In Case Of A Corporation, Partnership, Or Cooperative; Or Original Special Power Of Attorney Of All Members Of The Joint Venture Giving Full Power And Authority To Its Officer To Sign The Oss And Do Acts To Represent The Bidder, 5) Latest Income/business Tax Return, 6) Pcab License (license Category - C & D, Size Range - Small B), 7) Certificate Of Satisfactory Performance Issued By The Bureau Of Customs (for Contracts Entered Into With The Bureau) Or From Any Other Office/agency, If The Former Is Not Applicable And 8) Duly Signed Price Quotation Form (annex “a”). All Must Be Properly Signed And Sealed. Must Be Submitted In Hard Copy. Submission Of Quotation And Eligibility Documents In Hard Copy Is On Or Before November 18, 2024, 10:00 A.m., At General Services Division (gsd), Ground Floor, Ocom Building, Port Area, Manila. Award Of Contract Shall Be Made To The Lowest Quotation, Which Complies With The Minimum Description As Stated Above And Other Terms And Conditions Stated In The Price Quotation Form. Awarded Bidder Must Secure Performance Security/performance Bond 30% Of Contract Price Upon Receipt Of Notice Of Award. Any Interlineations, Erasures Or Overwriting Shall Be Valid Only If They Are Signed Or Initialed By The Bidder Or His/her Duly Authorized Representative/s. The Boc Reserves The Right To Accept Or Reject Any Or All Quotations And To Impose Additional Terms And Conditions As It May Deem Proper.

Details: Description Roll Acetate (plastic Cover), Gauge#8, 50 Meters Length 2 Packet Battery, Size Aaa, Alkaline 2 Pcs/packet-expiration Date: June 30, 2027 Or Beyond 50 Packet Battery, Size Aa, Alkaline 2 Pcs/packet-expiration Date: June 30, 2027 Or Beyond 55 Packet Battery, Size Aa Rechargeable, 2 Pcs./packet -expiration Date: June 30, 2027 Or Beyond 49 Piece Battery Charger- 4 Pieces Capacity 10 Box Binder Clip-51 Mm 40 Box Binder Clip-41 Mm 40 Box Binder Clip- 1 Inch 60 Roll Binding Tape 2" 15 Pair Book Ends, 9" 30 Box Carbon Paper Long- Blue 3 Pack Cartolina Assorted Colors (color: Red, Yellow, Light Green, Dark Green, Orange, Blue, Violet) 6 Piece Carpeta 3000 Piece Calculator, 12 Digit, Heavy Duty 7 Piece Cash Book (bank) General Form 104 12 Piece Certificate Holder, Legal, Color Green 10 Piece Certificate Holder, A4, Color Green 10 Piece Clip Board With Cover 40 Piece Cork Board Aluminum Frame, 2ft X 3ft, Plywood Backing 3 Piece Cork Board Aluminum Frame, 4ft X 3ft, Plywood Backing 3 Piece Correction Tape, 12mx5mm 380 Piece Cutter, Big, Heavy Duty 8 Piece Cutter Blade- Big, Ordinary 20 Piece Cutter Blade- Small, Ordinary 20 Piece Gun Tacker , T50 High Quality 4 Box Gun Tacker Wire , T50 1/2 24 Piece Document File Folder Long With Fastener (color: Green) 20 Piece Envelope, Expanding, Plastic W/handle & Push Lock 45 Piece Envelope, Expanding, Kraft, Legal Size, Brown (envelope With Tie) 300 Piece Envelope, Mailing 3000 Piece Eraser, Rubber, Heavy Duty 20 Piece Eraser, Felt. For Blackboard Or Whiteboard 8 Box Fastener, Plastic 40 Box Fastener, Metal 60 Pack File Divider, A4 26 Piece Folder, Expanding (emerald Green) 1900 Piece Folder, Expanding (blue) 300 Piece Folder, Expanding (red) 300 Set Fluorescent Light,40w W/ Complete Accessories 12 Piece Fluorescent Light, Refill 40w 7 Unit Filing Cabinet, Steel, 4 Drawers 9 Unit Filing Cabinet, Steel, 5 Drawers, Map Size (records), High Quality 3 Bottle Glue, 300ml 30 Pack Index Card 5*8 (100pieces/pack) 12 Pack Index Card 4*6 (100pieces/pack) 15 Piece Glue Gun, Medium Size 5 Piece Glue Gun Stick, Medium Size 150 Piece Laminating Film, A4, Thickness: 250 Microns 600 Piece Led Bulb, 15-20 Watts 100 Piece Led T8 Tube, 9w, 6500k *(fsl), High Quality (replacement) 15 Pack Linen Paper A4, Specialty Paper, 10 Pcs/pack 30 Piece Magazine Box, Single Compartment Color: Navy Blue 115 Piece Magazine Box, Double Compartment 55 Case Map Pin, Round Head (100pcs/case) 6 Piece Marking Pen , Whiteboard, Black (broad) 96 Piece Marking Pen , Whiteboard, Black (fine) 96 Piece Marking Pen, Whiteboard, Red (fine) 58 Piece Marking Pen, Whiteboard, Blue (fine) 58 Roll Masking Tape 48mm 20 Piece Memory-ddr 4, 2400mhz Sodimm, 8gb Ram(for Laptop-amor) 1 Piece Notebook- Steno 70 Ream Paper, A3, 80gsm 10 Piece Paper Sticker, Legal Size 250 Box Paper Clip, Jumbo, 48mm 50 Box Paper Clip, Small 50 Piece Paper Cutter-metal For Legal Size Paper 1 Pad Paper Yellow Pad, Thick 50 Piece Pencil, Lead With Eraser, High Quality 110 Ream Parchment Paper, Legal 1 Piece Pencil , Mechanical, .5 2 Piece Pencil , Mechanical (refill), .5 5 Piece Pencil Sharpener, Rotary 4 Piece Permanent Marker (green, Fine), Branded 22 Piece Permanent Marker (black, Fine) , Branded 144 Piece Permanent Marker (blue, Fine) , Branded 34 Piece Permanent Marker (red, Fine) , Branded 34 Piece Permanent Marker (black, Broad) , Branded 108 Piece Permanent Marker (blue, Broad) , Branded 24 Piece Permanent Marker (red, Broad) , Branded 24 Piece Philippine National Flag, Size:36" X 70" / Regular Size (big) 15 Piece Philippine National Flag ,flaglet, Nylon,with Stick Size: 11"x8" 40 Pack Photo Paper, A4 (20 Pcs / Pack) 60 Pad Post-it/ Sticky Note Pad, 3 X 4", Bright Color 130 Piece Pincher (staple Wire Remover), Flier Type 11 Piece Puncher, Big, Heavy Duty 9 Case Push Pin, With Diff.color Head, Flat Head Type 11 Box Pvc Cover, A4, 200mic Or Higher, (100pcs/box) 6 Box Pvc Cover , Legal ,200mic Or Higher, (100pcs/box) 3 Book Record Book 200 Pp.size: 176mm X 285mm 15 Book Record Book, 300 Pages , 25 Piece Record Book, 500 Pages, 214mm X 278mm 25 Piece Ring Binder, 3/4" 15 Piece Ring Binder 1/2" 15 Piece Ring Binder 1" 15 Piece Ruler -plastic , High Quality 16 Piece Ruler -metal , High Quality (24 Inches) 7 Piece Metric Scale, Regular 5 Piece Metric Scale, 6 Inches 5 Piece Styrofoam Board (1 Inch Thick) 5 Piece Styrofoam Board (1/2 Inch Thick) 5 Pair Scissors , Heavy Duty, Big 40 Piece Super Glue/instant Glue For Plastic, Ceramic, Leather, Rubber, And Other Materials. 20 Piece Signpen ( .5) , Black 300 Piece Signpen ( .5) ,blue 84 Piece Signpen ( .5) ,red 30 Piece Signpen (.7), Black 276 Box Signpen Grip 1.0, Branded 17 Piece Special Paper, Board Paper , (pale Cream), A4, 200gsm 400 Piece Special Paper, Board Paper , (pale Cream), Legal , 200gsm 600 Piece Highlighting Pen (color : Orange, Yellow And Green) 40 Piece Stamping Dater 4 Piece Stamp Pad , #1 13 Bottle Stamp Pad Ink Refill, Color: Green 9 Bottle Stamp Pad Ink Refill, Color: Black 20 Bottle Stamp Pad Ink Refill, Color: Red 9 Bottle Stamp Pad Ink Refill, Color: Violet 24 Bottle Stamp Pad Ink Refill, Color: Blue 11 Piece Stamp Pad , Felt Pad,66mm X 100mm 7 Box Rubber Band #18 11 Piece Stapler #35 With Staple Wire Remover, Heavy Duty 28 Box Staple Wire # 35 100 Box Staple Wire For #0399 (8mm) 12 Box Staple Wire For #0399 (10mm) 12 Box Storage File Box (large Size) 19 Piece Tape Dispenser , Table Top 6 Roll Tape , Double Sided ,1 Inches Wide 45 Roll Tape , Double Sided With Foam 25 Roll Tape, Masking 24mm 45 Roll Tape, Transparent 24mm, 50 Meters 125 Roll Tape , Transparent, 48mm, 50meters 30 Piece Extension Wire, 10 Meters With Switch 9 Piece Digital Clock 7 Piece Wall Clock 6 Piece Wooden Box For Index Cards, (for Cards 4x6 Size) 2 Piece Wooden Box For Index Cards, (for Cards 5x8 Size) 6 Piece White Board 2x3ft 3 Piece White Board 4x3ft 2 Piece White Board 4x6ft 2 Piece White Plotter Paper (24inches X 50 Yards 5 Gallon Alcohol, 70%, Isoprohyl 70 Bottle Air Freshener 280-300 Ml. 79 Piece Bathroom Soap 57 Gal Bleaching Liquid 26 Bundle Broom-hard-thick (walis Ting-ting) 40 Piece Broom-soft-thick, Heavy Duty 30 Piece Brush For Toilet Bowl, High Quality (with Holder) 46 Piece Brush For Toilet/ Bathroom Flooring With Long Handle , High Quality 10 Yard Coil Matting (rubber Doormat) 8 Pack Detergent Bar, Jumbo 30 Pack Detergent Powder, 1kg/pack All Purpose, High Quality 55 Piece Dipper (tabo), High Quality 28 Jar Dishwashing Paste, Branded, 500 Grams 60 Can Disinfectant Spray , 510g Or More (kills Germs,molds & Mildew), Branded 52 Piece Doormat, Cloth, High Quality 144 Piece Doormat, Rubberized 24 Piece Dust Pan, Steel Heavy Duty 12 Piece Duster 16 Pack Fabric Conditioner, 800ml 55 Gallon Floorwax Liquid, Red 6 Piece Furniture Cleaner, 300ml 29 Bottle Glass Cleaner Spray, 500ml 53 Piece Hand Brush For Wall Tiles 27 Pair Hand Gloves, Rubber, High Quality 25 Bottle Hand Sanitizer, 500ml 35 Bottle Hand Soap, Liquid, Anti Bacterial 85 Can Insecticide, 600ml, Odorless, Branded 95 Bottle Liquid Soap Dispenser (plastic, Ordinary) 10 Rolls Microfilm 100 Microns (42"x20"), Branded, High Quality 5 Gallon Muriatic Acid 18 Piece Pail , Medium, High Quality, 24l 16 Piece Pail , Medium, High Quality, 12l 14 Roll Plastic Twine, 1 Kg 12 Piece Rags 140 Piece Sack-big, 50kls 380 Piece Scouring Pad With Foam, Economy Size 67 Piece Scrub (cleaner For Sink With Handle) 20 Piece Trash Bag, Plastic Drum Size, Xl 1200 Bottle Toilet Bowl & Urinal Cleaner 68 Piece Toilet Rubber Force Pump 18 Piece Toilet Deodorant Cake 80 Rolls Toilet Tissue (individually Packed) 280 Set Tornado Mop W/ Extra Mop 11 Piece Trash Bin, 100l, With Foot Pedal And Wheels 18 Piece Soap Holder,plastic, High Quality 28 Piece Steel Wool, High Quality 20 Piece Spray Bottle (for Alcohol), 500ml 40 Piece Adaptor, 3 Gang To 2 Gang Flat 31 Piece Dvd Rewritable, 4x Speed,4.7 Gb Capacity 170 Piece External Hardrive Disk, 2 Tb 7 Piece Extension Wire, 10 Meters With Switch ( 2cpl, Planning) 12 Piece Flash Drive, 16 Gb 20 Piece Flash Drive, 32 Gb 23 Piece Micro Sd Card, 128gb Ultra Hd Class 10 (for Drone, Camera And Voice Recorder) 20 Piece Solid State Drive 1tb 3 Piece Mouse Pad, W/ Arm Rest 25 Piece Mouse Pad, W/o Arm Rest, Ordinary 15 Bottle Brother Printer Ink, Bt5000 (cyan), (genuine) -expiration Date: June 30, 2028 Or Beyond 23 Bottle Brother Printer Ink, Bt5000 (magenta), (genuine) -expiration Date: June 30, 2028 Or Beyond 23 Bottle Brother Printer Ink, Bt5000 (yellow), (genuine) -expiration Date: June 30, 2028 Or Beyond 23 Bottle Brother Printer Ink, Btd60 (black), (genuine) -expiration Date: June 30, 2028 Or Beyond 30 Unit Computer Table (tempered Glass) 3 Unit Document Color Duplex Scanner Scanner Type:sheet-fed, One-pass Duplex Color Scanner Photoelectric Device:color Contact Image Sensor (cis)optical Resolution:300 Dpicolor Bit Depth:30-bit Inputgrayscale Bit Depth:24-bit Outputlight Source:3-color Rgb Ledscanning Speed:35 Ppm/70 Ipm: 300 Dpi Black & White, Color, Gray1 Capacity: 50 Sheets, Document Sizes:, Paper Size Minimum: 2" X 2" Paper Size Maximum: 8.5" X 240, Daily Duty Cycle: 4,000 Sheets 4 Piece Document Monitor, 24", 75hz Fresh Rate W/ Hdmi Post & Cable Ips Panel (cpl & Cbfm ) 1 Piece Hdmi Cables, 5.0 M, High Quality (for Laptop, Projector) (for Cpl) 6 Bottle Ink Refill, Epson 003-black (genuine), (new Epson Seal) -expiration Date: June 30, 2028 Or Beyond 220 Bottle Ink Refill, Epson 003-cyan (genuine), (new Epson Seal) -expiration Date: -expiration Date: June 30, 2028 Or Beyond 85 Bottle Ink Refill, Epson 003-magenta (genuine), (new Epson Seal) -expiration Date: -expiration Date: June 30, 2028 Or Beyond 85 Bottle Ink Refill, Epson 003-yellow (genuine), (new Epson Seal) -expiration Date: -expiration Date: June 30, 2028 Or Beyond 85 Bottle Ink Refill, Epson 008-black (genuine), (new Epson Seal) -expiration Date: June 30, 2028 Or Beyond 5 Bottle Ink Refill, Epson 008-cyan (genuine), (new Epson Seal) -expiration Date: June 30, 2028 Or Beyond 3 Bottle Ink Refill, Epson 008-magenta (genuine), (new Epson Seal) -expiration Date: June 30, 2028 Or Beyond 3 Bottle Ink Refill, Epson 008-yellow (genuine), (new Epson Seal) -expiration Date: June 30, 2028 Or Beyond 3 Cartridge Ink Cartridge (hp Officejet Pro 7720) Black (955) Genuine -expiration Date: June 30, 2028 Or Beyond 4 Cartridge Ink Cartridge (hp Officejet Pro 7720) Cyan (955) Genuine -expiration Date: June 30, 2028 Or Beyond 4 Cartridge Ink Cartridge (hp Officejet Pro 7720) Magenta (955) Genuine -expiration Date: June 30, 2028 Or Beyond 4 Cartridge Ink Cartridge (hp Officejet Pro 7720) Yellow (955) Genuine -expiration Date: June 30, 2028 Or Beyond 4 Cartridge Ink Cartridge (hp Designjet T83) Black (728b) Genuine , 300ml -expiration Date: June 30, 2028 Or Beyond 1 Cartridge Ink Cartridge (hp Designjet T83) Cyan (728) Genuine -expiration Date: June 30, 2028 Or Beyond 1 Cartridge Ink Cartridge (hp Designjet T83) Magenta (728) Genuine -expiration Date: June 30, 2028 Or Beyond 1 Cartridge Ink Cartridge (hp Designjet T83) Yellow (728) Genuine -expiration Date: June 30, 2028 Or Beyond 1 Piece Laptop Backpack, High Quality 4 Piece Laptop Charger For Acer Aspire 3 A315-56-596k 2 Piece Laptop Li-on Battery Pack For Laptop Hp Probook, 450 G5 Battery(rr03xl) 1 Unit Megaphone, 50w W/ Recording And Sirens 2 Roll Typewritter Ribbon (big) 7 Piece Type C Usb Hub(design W/o Cable,4 Ports (for Iec) 2 Cartridge Epson Lx310 Ribbon Refill-expiration Date: June 30, 2026 Or Beyond 1 Piece Mouse, Optical, Usb Connection Type Connection 21 Piece Mouse, Wireless, Branded 5 Unit Printer, 3 In 1 W/ C.i.s Built-in. 8 Piece Projector White Screen With Tripod 3 Unit Active Portable Trolley Speaker 600w Max Power Bluetooth + Tws Usb & Sd Playback Fm Radio Line-in & Line-out 2 Guitar Input 2 Wired Mic Input 180 Channels Mic Priority High Quality Lead Acid 12ah Battery 12v Dc Input Dimensions : (l) 36.5cm (w) 40cm (h) 67.5cm 2 Free Wireless Mic 1 Piece Ups (backup) 625 Va Or Higher 19 Piece Ups (backup) 1600 Va Upc Limited 1 Piece Voice Recorder, Specs.: Digital Voice Recorder With 4gb Built-in Memory (expandable To 32gb Via Microsd), Supports Pcm And Mp3 Formats, Features Noise-cut, Auto Voice Recording, And Focus/wide-stereo Options, Has A Usb Direct Connection, And Offers Up To 55 Hours Of Battery Life Using 2 Aaa Batteries. 3 Piece Wireless/laser Pointer For Power Point Presentation, Heavy Duty 2 For Bams Set Binocular With Bag (special Feature:lightweight & Waterproof/objective Lens Diameter :50milimters/magnification Maximum:10x Bushnell -ultra High Power- Tres Forte Puissance -potencia Ultra-alta, Besonders Starke Vergroberung -60x90 Long Eye Relier , 231ft At 1000yds, 71m At 10000m 4 Piece Tree Diameter Tape 50meters 2 Piece Open Reel Fiberglass Long Tape Measure (60 Meters) 2 Piece Trowel 15 Piece Insect Net/mist Net 2 Piece Hollow Bar 10mm 2 Piece Snake Hook (heavy Duty) 2 Piece Snake Tong (heavy Duty) 2 Piece Dip Net 2 Rain Boots (high Quality) Men Sizes Piece 10" 8 Piece 9" 14 Piece 8" 29 Piece 7" 1 Women Sizes Piece 10" 1 Piece 9" 2 Piece 8" 3 Piece 7" 16 Piece 6" 10 Raincoat, Rubberized (high Quality) Men Sizes Piece Free Size 6 Piece 3xl 1 Piece 2xl 3 Piece Xl 11 Piece L 20 Piece M 17 Women Sizes Piece Free Size 1 Piece 2xl 2 Piece Xl 1 Piece L 2 Piece M 6 Piece S 14 Set First Aid Kit (set) 45 2 Absorbent Compress Dressings (5 X 9 Inches) 25 Adhesive Bandages (assorted Sizes) 1 Adhesive Cloth Tape (10 Yards X 1 Inch) 1 Antibiotic Ointment Packets (approximately 10 Grams) 5 Packs Antiseptic Wipe Packets (10s) 2 Packets Of Aspirin (81 Mg Each) 1 Emergency Blanket 1 Breathing Barrier (with One-way Valve) 1 Instant Cold Compress 2 Pair Of Nonlatex Gloves (size: Large) 2 Hydrocortisone Ointment Packets (approximately 1 Gram Each) 1 3 In. Gauze Roll (roller) Bandage 1 Roller Bandage (4 Inches Wide) 5 3 In. X 3 In. Sterile Gauze Pads 5 Sterile Gauze Pads (4 X 4 Inches) Oral Thermometer (non-mercury/nonglass) 2 Triangular Bandages Tweezers Emergency First Aid Instructions With Bag Set Portable Emergency Rescue Stretcher, Heavy Duty 8 Piece Finger Clip Pulse Oximeter Blood Oxygen Monitor Finger Pulse Heart Rate Meter, High Precision 8

Details: Description Request For Quotation For The Provision Of Lights And Sound With Led… 1. The Department Of Agriculture-regional Field Office 7 (da-rfo 7), Through The General Appropriation Act For Cy 2024 Intends To Apply The Sum Of Two Hundred Seventy-five Thousand Pesos (₱275,000.00) Being The Approved Budget For The Contract (abc) To Payments Under The Contract For Provision Of Flowers For Physical Arrangement. 2. The Department Of Agriculture-regional Field Office 7 (da-rfo 7), Now Invites Bids All Philgeps Registered Contractors/ Bidders Provision Of Lights And Sound With Led With The Following Specification: -1 Lot Provision Of Lights And Sound With Led @ 275,000.00 Unit Cost Date: December 3, 2024 Venue: Cebu City Inclusions: -1 Teleprompter -4 Units Wireless Handheld Microphones -1 Unit Tp T1 Wireless Transmitter (audio Delay) -4 Units Corded Microphone (for Back-up) -inverted U Truss 18x40 Ft Audio Equipment: -24 Units Powered Speaker -12 Pieces Subwoofer -2 Units Wedge Monitor -1 Unit Digital Mixer -1 Unit Audio Mixer Lights: -24 Units Par Led 54x3 -24 Units Beam Moving Head -8 Units Stormy -4 Units Audience Light -1 Unit Digital Light Controller -2 Unit Follow Spot -1 Unit Haze Machine -4 Units T Bars Video: -1 Set (center) 24ft (w) X 9ft (h) Led Wall -2 Sets (strip) 2ft (w) X 9ft (h) Led Wall -2 Sets (sides) 6ft (w) X 9ft (h) Led Wall -1 Unit Sending Processor -1 Unit Video Switcher/video Splitter Amplifier -1 Lot Video Cables, Connectors, And Wires -1 Set Led Wall Platform -1 Unit Laptop For Videos -2 Unit Livefeed Camera Communication Set: -6 Pieces Two(2) Way Communication Set For The Pcaf Event Team (should Have Separate Comsets For Tech Booth) Confetti Effects: -2 Units Confetti Blaster Willing To Pay 15,000-18,000 Electricity Charge Payable To The Venue/hotel Direct Billing: 100% Payment Upon Completion 3. The Bidder Must Submit Mayor’s Permit And Philgeps Registration Number. The Office Will Require The Winning Bidder To Submit Omnibus Sworn Statement Prior To The Issuance Of The Notice Of Award (noa). 4. Interested Bidders May Obtain Further Information From Department Of Agriculture-regional Field Office 7 (da-rfo 7) And Inspect The Canvass Forms And Other Documents At The Address Given Below From 8:00 A.m. - 5:00 P.m. Procurement Unit Department Of Agriculture Regional Field Office 7 Da-rfo 7 Complex, M.c. Briones Street, Highway Maguikay, Mandaue City 5. Bids Must Be Delivered Together With The Required Legal Documents Stated At Item Number 3, To Bac Chairperson/ The Procurement Section At Da- Rfo 7, Da-rfo 7 Complex, M.c. Briones Street, Highway Maguikay, Mandaue City. 6. Open But Signed Bids/quotations May Be Submitted Through Facsimile Or Email, Together With The Required Documents Stated At Item Number 3, At The Addressed And Contact Numbers Indicated Below: Procurement Unit Department Of Agriculture Regional Field Office 7 Tel No. 032-2682698 Fax No. 032-2563063 Telefax No. 032-2682698 Darfu7@ymail.com/da7ps@yahoo.com 7. The Department Of Agriculture Regional Field Office 7 (da-rfo 7) Reserves The Right To Accept Or Reject Any Bid, To Annul The Bidding Process, And To Reject All Bids At Any Time Prior To Contract Award, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 8. For Further Information And Required Documents To Be Submitted, Please Contact: Procurement Unit Department Of Agriculture Regional Field Unit-7 Tel No. 032-2682698 Fax Number 032- 256-3063 (sgd.) Fabio G. Enriquez, Ph.d. Bac Chairperson

Details: Description Item No. Description Qty. Unit Unit Cost Total Amount 1 Ob-ultrasound Reception And Ultrasound Room Extension & Improvement 1 Lot 263,655.00 263,655.00 Ob-ultrasound Reception And Ultrasound Room Extension & Improvement Drywall, Door And Ceiling 3/4" Thick Marine Plywood 1 Sheet 1,250.00 1,250.00 6mm Thick Ficem Board - Drywall (double Wall) 10 Sheets 800.00 8,000.00 3.5mm Thick Ficem Board - Ceiling 4 Sheets 400.00 1,600.00 Double Metal Furring 6 Pcs. 124.00 744.00 Wall Angle 5 Pcs. 90.00 450.00 Carrying Channel 4 Pcs. 105.00 420.00 2"x4" Metal Studs 16 Pcs. 165.00 2,640.00 2"x4" Metal Tracks 8 Pcs. 165.00 1,320.00 Blind Rivets 5/32" X 1/2" 2 Box 250.00 500.00 Blind Rivets 5/32" X 3/4" 3 Box 250.00 750.00 Solid Core Panel Door Double Leaf Set With 2"x4" Hardwood Door Jamb (40x210cm, 80x210cm) 1 Set 12,500.00 12,500.00 Stainless Chain Bolt 1 Set 600.00 600.00 Stainless Dead Bolt Lock 1 Pc. 900.00 900.00 Stainless Push And Pull Plate Handles 1 Set 750.00 750.00 Painting Works Acrytex Cast 6 Galloons 650.00 3,900.00 Acrytex Reducer 3 Galloons 500.00 1,500.00 Acrytex Primer - Ceiling And Wall Primer 8 Galloons 1,050.00 8,400.00 Acrytex Topcoat - Wall Topcoat 4 Galloons 1,200.00 4,800.00 Acrytex Tenting Color - (assorted) 10 Cans 125.00 1,250.00 Flat Latex - Ceilingtopcoat 2 Galloons 950.00 1,900.00 Marine Epoxy 1 Galloons 2,900.00 2,900.00 #80 Sand Paper 6 Sheets 95.00 570.00 #240 Sand Paper 3 Sheets 75.00 225.00 Paint Roller - Baby Roller 4 Pcs. 75.00 300.00 Oil Wood Stain - Maple(boysen Maple) 1 Liter 175.00 175.00 Sanding Sealer 2 Liters 380.00 760.00 Lacquer Topcoat Deadflat 1 Liters 425.00 425.00 Lacquer Thinner 1 Liters 350.00 350.00 Reception Wall Signage 16.5cm Wpc Fluted Wall Panels (90cm Wide Installation) With Fasteners & Clips 7 Pcs. 750.00 5,250.00 4.5inch Stainless Signage "astmmc Ob-gyne Ultrasound Center" & Astmmc Logo 1 Set 25,000.00 25,000.00 Acrylic Sign "center For Ob-gyne Ultrasound" 1 Set 3,500.00 3,500.00 Office Furniture’s And Others Tv Wall Mount Folding Bracket 1 Set 600.00 600.00 Ergonomic Delux 3 Seaters Metal Gang Chair (synthetic Leather Finished Gang Chair With Seat And Backrest Foam Padding, End To End Armrests, With Heavy Duty Steel Beam And Base For Heavy Loads) 1 Assembly 18,500.00 18,500.00 Ergonomic Office Chair 360˚rotating With Adjustable Lift 1 Pc. 3,600.00 3,600.00 Leather Chrome High Chair With Backrest, 360˚rotating With Adjustable Lift 1 Pc. 5,500.00 5,500.00 60x120 Office Table With Cable Grommet 1 Set 6,500.00 6,500.00 3/4" Stainless Curtain Rod With Hangers Set With Alphagina Curtain(ask For End User's Color Preference) 3 Set 2,500.00 7,500.00 24cm X 94cm X Ceiling Height Built-in Laminated Marine Board Open Shelf 1 Set 6,500.00 6,500.00 Electrical/mechanical Works 2hp Wall Mounted, Spit Type Aircon W/ Installation, Testing & Commissioning And 30 Ft Excess Copper Tube, Specs: Inverter Type, R-410a Or R-32 Refrigerant, With Bracket 1 Lot 51,090.00 51,090.00 12" Exhaust Fan, Wall Mount 1 Lot 1,900.00 1,900.00 Linear Tracklight 3pcs. @9watts Warm Spotlight Complete Set 1 Set 4,750.00 4,750.00 3.5mm2 Thhn Copper Wire 1.5 Roll 4,300.00 6,450.00 2.0mm2 Thhn Copper Wire 1 Roll 3,200.00 3,200.00 8.0mm2 Thhn Copper Wire 60 Meter 65.00 3,900.00 15watts , Led Downlight Lamp 9" Diameter 6 Set 800.00 4,800.00 Pinlight Holder Bulb-type 9" Diameter 1 Pc. 500.00 500.00 100-300w Incandescent Bulb 1 Pc. 400.00 400.00 Dimmer Switch 1 Set 1,200.00 1,200.00 Two Gang Single Pole Switch 2 Set 300.00 600.00 Duplex Convenience Outlet 6 Set 270.00 1,620.00 Aircon Outlet 1 Set 200.00 200.00 6-branches Panelboard (plug-in Type) 1 Set 4,200.00 4,200.00 1-50a, 230v, 1-phase Acb Main 3-20a, 230v, 1-phase Acb 2-30a, 230v, 1-phase Acb 1 1/4" Dia. Pvc Pipe With Coupling 14 Length 116.00 1,624.00 1" Dia. Pvc Short Elbow 16 Pcs. 36.00 576.00 3/4" Plastic Molding 10 Length 66.00 660.00 1" Plastic Molding 4 Length 75.00 300.00 1/2" Plastic Molding 2 Length 48.00 96.00 Pvc Clamp 1" Diameter (150pcs. Per Pack) 1 Length 180.00 180.00 Electrical Tape Big 2 Pcs. 40.00 80.00 Sub-total 230,655.00 Scope Of Works Removal/dismantling Of Existing Structures, Hauling To Efms Site 1 Lot 3,500.00 3,500.00 Drywall And Ceiling Frames And Board-ups And Painting 1 Lot 17,500.00 17,500.00 Installation Fluted Panels 1 Lot 1,500.00 1,500.00 Electrical Works 1 Lot 10,500.00 10,500.00 Sub-total 33,000.00 Total Amount 263,655.00

Description: Contract notice – general guideline, standard regulation negotiated procedure with prior publication of a call for competition/negotiated procedure (services) Specialist planning in electrical engineering for the implementation of the space requirement planning at the Kirchhain primary school Description: Specialist planning in electrical engineering, in accordance with Part 4, Section 2, Hoai; system groups (4), (5) and ... Multiple planning in electrical engineering for the implementation of the space requirement planning at the Kirchhain primary school Description: Specialist planning in electrical engineering, in accordance with Part 4, Section 2, Hoai; system groups (4), (5) and (6) in accordance with Section 53 Paragraph 2 Hoai for the implementation of the space requirement planning at the Kirchhain primary school. The Kirchhain primary school is a four-stream primary school which is currently attended by around 360 pupils in grades one to four as well as a so-called preparatory class and two preparatory courses and is taught by around 30 teachers. The three school buildings in the northern part of the site, which are arranged as individual, elongated structures parallel to one another, are accessed via individual entrances and connected to one another by an external arcade. Most students enter the school grounds from the north via Pestalozzistrasse. In the south there is another single-storey building, which primarily contains rooms for childcare. House 1 (building 31.001) of the Kirchhain primary school is a 4-storey school building (ground floor to 3rd floor) that was completely renovated in 2011 with funds from the State of Hesse's special investment program and received structured cabling with funds from the Digital Pact for Schools. The administration with the secretariat and school management office are currently housed on the ground floor and classrooms on the upper floors. Houses 2 (building 31.004, 4-storey with basement, basement to 2nd floor) and 3 (building 31.006, 3-storey, ground floor to 2nd floor) are from the 1950s and have been partially renovated. The technical center for the school's heat supply is currently housed in the basement of house 2 (building 31.004). The project is to connect the site to an adjacent district heating network. The inclusion of differentiation rooms, adaptations of the room structures to the pedagogical concept with learning clusters and the requirements for all-day schooling require significant interventions in the existing structure, which may even lead to a partial replacement building to represent the spatial and functional program. In the course of procuring the object planning services for buildings, a proposed solution was developed that is intended as the basis for this process and the further planning steps. The following key data must also be observed during planning and implementation support: - Potential replacement buildings are to be planned/built to passive house standards without certification (including participation in the management of the "phpp" planning tool) - The building is to be planned according to the standards of the Digital Pact for Schools and digital working. In addition to a good network structure with integration into the existing building, full-surface WiFi coverage is a matter of course - Implementation of the requirements for all-day provision - Total project budget to be adhered to: €10.5 million gross - Participation in the planning for the relocation of students (fully or partially) is to be carried out (supplying the interim accommodation with media) - Federal funding for the expansion of all-day provision is sought. This is intended to achieve partial financing, which requires a special documentation obligation for the planning services. Support is required from the specialist planning services in question, such as details of LED lighting and the control of electrical systems. A lighting concept is to be developed for the teaching room and the cafeteria in the building. Due to the high energy standards, a PV system is to be planned. Internal identifier: Lot-0001 Specialist electrical engineering planning for the implementation of the space requirement planning at the Kirchhain primary school Description: Specialist electrical engineering planning, in accordance with Part 4, Section 2, Hoai; system groups (4), (5) and (6) in accordance with Section 53 Paragraph 2 Hoai for the implementation of the space requirement planning at the Kirchhain primary school. The Kirchhain primary school is a four-stream primary school, which is currently attended by around 360 pupils in grades one to four, as well as a so-called preparatory class and two preparatory courses, and is taught by around 30 teachers. The three school buildings in the northern part of the site, which are arranged as individual, elongated structures parallel to one another, are accessed via individual entrances and connected to one another by an external arcade. Most students enter the school grounds from the north via Pestalozzistrasse. In the south there is another single-storey building, which primarily contains rooms for childcare. House 1 (building 31.001) of the Kirchhain primary school is a 4-storey school building (ground floor to 3rd floor) that was completely renovated in 2011 with funds from the State of Hesse's special investment program and received structured cabling with funds from the Digital Pact for Schools. The administration with the secretariat and school management office are currently housed on the ground floor and classrooms on the upper floors. Houses 2 (building 31.004, 4-storey with basement, basement to 2nd floor) and 3 (building 31.006, 3-storey, ground floor to 2nd floor) are from the 1950s and have been partially renovated. The technical center for the school's heat supply is currently housed in the basement of house 2 (building 31.004). The project is to connect the site to an adjacent district heating network. The inclusion of differentiation rooms, adaptations of the room structures to the pedagogical concept with learning clusters and the requirements for all-day schooling require significant interventions in the existing structure, which may even lead to a partial replacement building to represent the spatial and functional program. In the course of procuring the object planning services for buildings, a proposed solution was developed that is intended as the basis for this process and the further planning steps. The following key data must also be observed during planning and implementation support: - Potential replacement buildings are to be planned/built to passive house standards without certification (including participation in the management of the "phpp" planning tool) - The building is to be planned according to the standards of the Digital Pact for Schools and digital working. In addition to a good network structure with integration into the existing building, full-surface WiFi coverage is a matter of course - Implementation of the requirements for all-day provision - Total project budget to be adhered to: €10.5 million gross - Participation in the planning for the relocation of students (fully or partially) is to be carried out (supplying the interim accommodation with media) - Federal funding for the expansion of all-day provision is sought. This is intended to achieve partial financing, which requires a special documentation obligation for the planning services. Support is required from the specialist planning services in question, such as details of LED lighting and the control of electrical systems. A lighting concept for the teaching room and the cafeteria is to be developed for the building. Due to the high energy standards, a PV system is to be planned. Internal ID: Lot-0001

Details: Description Bids And Awards Committee Invitation To Bid Ib 24-g103 The Department Of Health – Central Visayas Center For Health Development (doh – Cv Chd), Through Its Bids And Awards Committee (bac), Invites Suppliers To Bid For The Hereunder Items: Bac No. 2024-g93 Name Of Project Procurement Of One Job Order For Materials For The Construction Of 3 Meter High Perimeter Fence For Doh Visayas Hub Warehouse At Eversley Childs Sanitarium Jagobiao, Mandaue City, Cebu Estimated Unit Cost (php) Approved Budget Of The Contract (php) Price Of Bid Documents (php) Source Of Funds Lot 1 1.1 - 707 Bag/s Cement 270.00 190,890.00 2024 Phm-lhsd Chief 1.2 - 30 Cu.m Sand 2,200.00 66,000.00 1.3 - 61 Cu.m 3/8” Gravel 2,200.00 134,200.00 1.4 - 2,950 Pc/s 6’’ Chb 25.00 73,750.00 1.5 - 875 Pc/s 12mm X 6m Dsb 330.00 288,750.00 1.6 - 50 Kg/s #16 G.i. Tie Wire 100.00 5,000.00 1.7 - 20 Sheets 3/8 X 4 8” Ordinary Plywood 460.00 9,200.00 1.8 - 40 Pc/s 2” X 2” 10’ Coco Lumber 90.00 3,600.00 1.9 - 80 Pc/s 2” X 3” 10’ Coco Lumber 130.00 10,400.00 1.10 - 9 Kg/s Common Nails 1” 95.00 855.00 1.11 - 9 Kg/s Common Nails 3” 95.00 855.00 1.12 - 9 Kg/s Common Nails 4” 95.00 855.00 1.13 - 9 Kg/s Concrete Nails 2” 106.00 954.00 1.14 - 9 Kg/s Concrete Nails 4” 106.00 954.00 1.15 - 10 Pail Skim Coat 1600.00 16,000.00 1.16 - 30 Gal/s Primer Paint 790.00 23,700.00 1.17 - 30 Gal/s Semi-gloss Latex, 4l (2 Coats) 660.00 19,800.00 1.18 - 1 Gal/s Epoxy Paint 1350.00 1,350.00 1.19 - 10 Gal/s Lacquer Thinner 660.00 6,600.00 1.20 - 13 Sheets #100 Sand Paper 20.00 260.00 1.21 - 13 Sheets #120 Sand Paper 22.00 286.00 1.22 - 13 Pc/s 2” Paint Brush 20.00 260.00 1.23 - 3 Pc/s 3” Roller Brush W/ Handle (cotton) 60.00 180.00 1.24 - 14 Pc/s 10” Roller Brush W/ Handle (cotton) 80.00 1,120.00 1.25 - 8 Pc/s Paint Tray 80.00 640.00 1.26 - 24 Rolls Masking Tape 1” 35.00 840.00 1.27 - 10 Kg/s Waste Cotton 100.00 1,000.00 1.28 - 20 Length/s 25mmø Pvc Pipe 160.00 3,200.00 Lot 1 1.29 - 3 Rolls 3.5mm Sq. Thwn Wire 4,500.00 13,500.00 1.30 - 40 Pc/s Utility Box 60.00 2,400.00 1.31 - 9 Pc/s Electrical Tape 48.00 432.00 1.32 - 4 Cans Pvc Solvent Cement 400cc 186.00 744.00 1.33 - 550 Pcs Assorted Tox 2.00 1,100.00 1.34 - 550 Pcs Assorted Screw 3.00 1,650.00 1.35 - 20 Pcs Assorted Drill Bits 50.00 1,000.00 1.36 - 250 Pcs Cable Tie 8” 5.00 1,250.00 1.37 - 14 Set/s Flood Light(led) 40watts, Waterproof Ip67 2,900.00 40,600.00 1.38 - 12 Set/s Flood Light(led)100watts, Waterproof Ip67 2,900.00 34,800.00 1.39 - 2 Set/s Surface Mounted (led)40watts, Waterproof Ip67 1,500.00 3,000.00 1.40 - 2 Set/s Universal Convenience Outlet Waterproof Ip67 1,500.00 3,000.00 1.41 - 1 Set/s Surface Mounted Switch 2-gang Waterproof Ip67 1,500.00 1,500.00 Total Php 966,475.00 1,000.00 Prospective Bidders Should Have Experience In Undertaking At Least One (1) Similar Project Within Five (5) Years From The Opening Of Bids With An Amount Of At Least 25% Of The Proposed Project For Bidding. For Bac Projects Having Several Items Or Lots, Prospective Bidders Shall Submit One Bid Form For Each Item Or Lot, And Provide The Pertinent Details In The Schedule Of Prices. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii Of The Instructions To Bidders. The Eligibility Check/screening As Well As The Preliminary Examination Of Bids Shall Use The Non-discretionary “pass/fail” Criteria. Post-qualification Of The Lowest Calculated Bid Shall Be Conducted. All Particulars Relative To The Eligibility Statement And Screening, Bid Security, Performance Security, Pre-bidding Conference, Evaluation Of Bids, Post-qualification And Award Of Contract Shall Be Governed By The Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) 9184, Otherwise Known As The “government Procurement Reform Act”. The Complete Schedule Of Activities Is Listed, As Follows: Activities Schedule 1. Issuance Of Bid Documents November 9 – December 2, 2024 Procurement Unit, Administrative Building Doh – Cv Chd, Osmeña Boulevard, Cebu City 2. Pre-bid Conference November 18, 2024 At 10:00 Am (monday) Doh - Chapel (rhtc Building) Doh – Cv Chd, Osmeña Boulevard, Cebu City 3. Opening Of Bids December 2, 2024 At 9:00 Am (monday) Doh - Chapel (rhtc Building) Doh – Cv Chd, Osmeña Boulevard, Cebu City A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders From The Address Below And Upon Payment Of A Non-refundable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb. The Method Of Payment Will Be In Cash. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At The Bid Opening. The Doh – Cv Chd Reserves The Right To Accept Or Reject Any Bid, To Annul The Bidding Process, And To Reject All Bids At Any Time Prior To The Contract Award, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. Jonathan Neil V. Erasmo, Md, Mph, Fpsms Chairman, Bids And Awards Committee November 9, 2024 Department Of Health – Cv Chd Ms. Stefanie Lorraine D. Trinidad - Head Bac Secretariat Osmeña Boulevard, Cebu City Telephone No.: (032) 254-0075/260-9740 Local 414 And 415 Procurement@ro7.doh.gov.ph Mis.cvchd7.com/bidding/ (bac 2024– G93 Lot [goods])

Details: Description Item No. Item Description Qty. Unit Approved Budget For The Contract (abc) Statement Of Compliance Price Offer From Supplier/ Service Provider Abc Per Item Total Abc Offer Per Item Total Offer Lot No. 1 : Procurement Of Printers Abc: Php 228,744.52 Breakdown: 1 High-speed Multi-function Printer Technical Specifications: Printer Type: Inkjet Function: Print, Copy, Scan Print Speed: At Least 10 Ipm (black) Ccc Ccc At Least 8 Ipm (color) Print Resolution: At Least 4800 X 2400 Dpi Duplex Printing: Yes Colors Available: Black, Cyan, Magenta, Yellow Copy Speed: At Least 5 Ipm (black) At Least 2 Ipm (color) Copy Resolution: At Least 600 X 600 Dpi Scan Speed: At Least 5 Ipm (black) At Least 2 Ipm (color) Scanner Type: 1.a) Flatbed; 1.b) Flatbed W/ Adf Scan / Optical Resolution: At Least 1200 X 2400 Dpi Paper Input Tray: At Least 100 Sheets Paper Sizes Supported: Letter, A4, Legal, Folio Monthly Print Volume: At Least 2,000 Pages Connectivity: Usb 2.0, Ethernet Port (built-in) And Wifi 802. 11 (built-in) Inclusion: 1) Bundled Starter Ink; 2) Knowledge Transfer Or Basic End-user Training Warranty: One (1) Year On Parts, Labor And Services 10 Unit 14,400.67 144,006.67 Lot No. 1 : Procurement Of Printers (continuation) Abc: Php 228,744.52 Breakdown: 2 4-in-1 Printer Technical Specifications: Printer Type: Colored Printer Printer Function: Print, Scan, Copy, Fax Print Speed: At Least 35ppm (mono); At Least 30ppm (colored) Print Resolution: 4800 X 1200 Dpi Or Higher Bi-directional Printing: Yes Copy Speed: At Least 25 Ipm (mono); At Least 15 Ipm (colored) Copy Resolution: 600x 600 Dpi Or Higher Scan Speed: At Least 25 Ipm (mono & Colored) Optical Resolution: 1200 X 1200 Dpi Or Higher Paper Input Tray: At Least 200 Sheets Paper Output Tray: At Least 100 Sheets Connectivity: Usb 2.0, Built-in Ethernet, Built-in Wi-fi Os Supported: Windows 10 Or Higher & Its Counter Equivalent Warranty: At Least One (1) Year On Parts And Services 3 Unit 21,064.00 63,192.00 Lot No. 1 : Procurement Of Printers (continuation) Abc: Php 228,744.52 Breakdown: 3 Multifunction Eco Tank Printer Technical Specifications: Printer Function: Print, Copy, Scan Printer Type: Inkjet/ink Tank Print Speed: 15.5 Ipm (black); 8.5 Ipm (colored) Print Resolution: 1200 X 4800 Dpi Copy Speed: 11 Ipm (black); 5.5 Ipm (colored) Copy Resolution: 600x 600 Dpi Scan Type: Adf Scan Speed (flatbed): 12sec (black) 27sec (colored) Optical/scan Resolution: 1200 X 2400 Dpi Paper Size Supported: A4, Legal, Letter Paper Input Tray: Atleast 150 Sheets Paper Output Tray: At Least 30 Sheets Connectivity: Usb 3.0 With Backward Compatibility To Usb 2.0, Ethernet, Wireless Capable (wifi) Supported Os: Windows 10 Or Higher & Equivalent Warranty: One (1) Year On Parts And Services Special Features: Bordless Printing Duplex Printing 1 Unit 21,545.85 21,545.85 Grand Total Lot 1: Lot No. 2 : Procurement Of Ict Accessories Abc: Php 9,573.20 Breakdown: 1 Wireless Laser Pen Connection Type: 2.4ghz Wireless Connection Laser Color: Red Buttons: 3 Operating Range: At Least 100m Receiver: Nano Usb Receiver Receiver Storage: Magnetic Accessories: At Least One (1) Aa Battery Os Compatibility: Windows 10 Or Higher And Its Counter Equivalent Warranty: At Least One (1)year Warranty 1 Pc 1,385.67 1,385.67 2 Usb Flash Drive Type: Flash Drive Storage Capacity: At Least 32 Gb Interface: Usb 3.0 And Usb 2.0 Compatible Plug And Play: Yes Os Compatibility: Windows 10 Or Higher And It's Counter Equivalent Warranty: At Least One (1) Year Warranty 14 Pc 392.80 5,499.20 Lot No. 2 : Procurement Of Ict Accessories (continuation) Abc: Php 9,573.20 Breakdown: Hdmi Cord Cable Type: At Least High Speed (category2) Resolution: At Least 1080p Length: At Least 5 Meters Bandwidth: 10.2 Gb/s Warranty: At Least One (1) Year Warranty 1 Pc 700.00 700.00 Hdmi Splitter Number Of Outputs: At Least 3 Hdmi Version: Can Support Hdmi 1.4 Or Higher Resolution: Atleast 4k Or 1080p Warranty: At Least One (1) Year 1 Pc 1,988.33 1,988.33 Grand Total Lot 2: Reference: Pr No. 2024-06-446; 2024-06-447; 2024-06-492 Purpose: For Official Use Of Various Operating Units Delivery Period: 20 Calendar Days Upon Receipt Of Notice To Proceed (ntp) Instruction To Supplier: 1. The Project Shall Be Awarded As Separate Contract/po Each Lot. The Total Number Of Contract/ Po To Be Awarded For This Project Are Two (2). 2. For Each Lot, Supplier Must Indicate Either "comply" Or "not Comply" Against Each Line Item In The Statement Of Compliance. 3. All Line Items On The Lots Must Have Either Comply Or Not Comply Do Not Leave Blank Portion On The Lot. Failure To Do So Shall Be A Grounds For Rejection Of The Quote On The Lot. 4. The Offered Amount Per Item Should Not Exceed The Abc Per Item. Note: I. In Order To Be Eligible For This Procurement, Suppliers/service Providers Must Submit Together With The Quotation/proposal The Following Eligibility Requirements. 1. Valid Business Permit For Fy 2024 2. Philgeps Registration No. (please Indicate On The Space Provided Above) 3. Accomplished And Notarized Omnibus Sworn Statement (must Be Project Specific) (templates For Omnibus Sworn Statement May Access Through This Link : Http//gppb.gov.ph/downloadables.php) 4. Others: A. Any Documents To Prove That The Signatory Of The Quotation Is Authorized Representative Of The Company (e.g. Secretary Certificate, Dti Certificate, And The Like) Or B. Photocopy Of Company Id Bearing The Pictures/ Signature Of The Representatives. Other Instruction: * Please Submit Your Quotation Using Our Official Request For Quotation (rfq) Form. You Can Secure A Copy Of The Said Rfq Thru Dilg Website And Philgeps Website Or E-mail Us At Ppms2024.dilgco@gmail.com Deadline: *please Submit Your Quotation/s Together With The Eligibility Documents On/or Before November 18, 2024 At 12:00 Nn Addressed To The Dilg Shopping And Negotiated Procurement Committee (snpc) Through Any Of The Following: A. Email Us At Ppms2024.dilgco@gmail.com; B. Fax To Telefax No. 8926-6256 C. Deliver On Hand At The Lobby Area Of Dilg-napolcom Center, Edsa Corner Quezon Avenue, West Triangle, Quezon City

Details: Notice To Bidders Notice Is Hereby Given That Sealed Bids Will Be Received By The Mayor And Council Of The City Of Abbeville, Vermilion Parish, Louisiana, On-line With Http://www.centralbidding.com And At 101 North State Street, In The Council Meeting Room, Abbeville, Louisiana, Until 11:00 A.m., Tuesday, November 19, 2024, For: Abbeville Chris Crusta Memorial Airport Runway Lighting Upgrade State Project No. H.015957 And The Bids Will Be Opened And Read Aloud At That Time. Bids Received After The Specified Time Will Not Be Considered. The Work Will Consist Of Removing And Replacing Runway And Taxiway Lights And Associated Transformers, Reils, Threshold Lights, Regulators, Helipad Lighting, Radio Controller And Interface Panels, Guidance Signs, Rotating Beacon Light, Existing 5kv Cabling And Other Associated Work. A Non-mandatory Pre-bid Conference Will Be Held On Friday, November 8, 2024, At 10:00 A.m., At The Abbeville Chris Crusta Memorial Airport, 262 Jimmy C. Vorhoff Jr. Drive, Abbeville, La 70511. Only The Bids Of Contractors Licensed Under Louisiana Contractor’s Licensing Law Will Be Considered For Bids Exceeding $50,000.00. Should The Bid Exceed $50,000.00, Contractors Desiring To Bid Shall Submit Evidence That They Hold License Of Proper Classification Under “electrical” In Full Force And Effect At The Time Bidding Documents Are Requested From The Office Of The Engineers. It Is The Policy Of The Department Of Transportation (dot) That Disadvantaged Business Enterprises As Defined In 49 Cfr Part 26 Shall Have The Maximum Opportunity To Participate In The Performance Of Contracts Financed In Whole Or In Part With Federal Funds. As Evidence Of Good Faith Of The Bidder, A “bid Guarantee” Equivalent To 5% Of The Base Bid Plus Additive Alternates, Consisting Of A Firm Commitment, Such As A Bid Bond, Certified Check, Or Cashier’s Check, Shall Accompany Each Bid As Assurance That The Bidder Will, Upon Acceptance Of His Bid, Execute Such Contractual Documents As May Be Required And Within The Time Specified. If A Bid Bond Is Used, It Shall Be Written By A Surety Or Insurance Company Currently On The U.s. Department Of The Treasury Financial Management Service List Of Approved Bonding Companies, Which Is Published Annually In The Federal Register, Or By A Louisiana Domiciled Insurance Company With At Least An “a–” Rating In The Latest Printing Of The A.m. Best’s Key Rating Guide To Write Individual Bonds Up To 10% Of Policyholders’ Surplus, As Shown In The A.m. Best’s Key Rating Guide, Or By An Insurance Company In Good Standing Licensed To Write Bid Bonds Which Is Either Domiciled In Louisiana Or Owned By Louisiana Residents. The Successful Contractor Will Be Required To Execute A Performance Bond And A Payment Bond In The Full Amount Of The Contract As More Fully Defined In The Bidding Documents. Contractors May Obtain An Electronic Or Paper Set Of “bidding Documents” From The Design Engineer Listed Below At The Following Location And During The Specified Hours: 1. Sellers & Associates, Inc., 148-b Easy Street, Lafayette, La 70506-3095 Telephone: 337.232.0777 / Fax: 337.232.0851 Monday - Thursday: 7:30 A.m. To 12:00 Noon And 1:00 P.m. To 5:30 P.m. / Friday: 8:00 A.m. To 12:00 Noon Contractors May Also View And Download The “bidding Documents” With The Owner’s Electronic Bid Submittal Service: 1. Http://www.centralbidding.com Prospective Bidder May Register On-line In Order To Establish An Account. For Assistance On How To Register On-line Or If Encountering Problems With The Web Site, Contact Info Tech Fl At 888.352.bidx (2439). A $92.00 Deposit On The First Set Of Documents Furnished To All Prime Bidders, Who Request Bidding Documents And Who Are Properly Licensed By The Louisiana State Licensing Board For Contractors, Shall Be Fully Refunded Upon Return Of The Documents No Later Than 10-days After Receipt Of Bids. On Other Sets Of Documents Furnished To Bidders, $5.00 Shall Be Refunded Upon Return Of The Documents No Later Than 10-days After Receipt Of Bids. The Bidding Documents Shall Be Available Until 24-hours Before The Bid Opening Date. No Bidder May Withdraw His Bid For At Least 45-days After The Time Scheduled For The Opening Of Bids. This Provision Shall Not Be Subject To Waiver. The Provisions And Requirements Of This Section And Those Stated In The Bidding Documents Shall Not Be Waived By Any Entity. Attest: S/roslyn White S/kathleen Faulk Mayor City Clerk Official Journal: Abbeville Meridional / Publication Dates: October 23, October 30, And November 6, 2024 State Journal: The Advocate / Publication Dates: October 23, October 30, And November 6, 2024 Official On-line Service: Www.centralbidding.com

Purchaser Name: Insular Government Council Of The Insular Cable Of Tenerife | Provision of Collective Transport Services by Bus on the Island of Tenerife for Sports Activities Organized by the Administrative Sports Service of the Island Council of Tenerife