Cable Tenders
Cable Tenders
Philippine Science High School System - PSHS Tender
Civil And Construction...+1Civil Works Others
Philippines
Details: Description I General Requirements I.1 Contactors Temporary Facilities And Field Office Months 8 I.2 Material Testing Lot 1 I.3 Safety Signages And Barricades Lot 1 I.4 Construction Safety And Health Lot 1 I.5 Project Billboard Unit 2 I.6 Permits And Clearances I.6.1 Occupancy Permit Lot 1 I.6.2 Ecc Permit Lot 1 Ii Concrete Works Ii.1 Cast In Place Concrete, Fc'=23.13 Mpa (3500psi) Second Floor Ii.1.1 Lintel Beam Cu.m 4 Ii.1.2 Stiffiner Column Cu.m 2 Ii.2 Cast In Place Concrete, Fc'=27.4 Mpa (4000psi) Second Floor Ii.2.1 Column Cu.m 10 Ii.2.2 Roof Beam Cu.m 26 Ii.2.3 Stairs (stair 1 And 2) Cu.m 14 Iii Reinforcing Steel Bars (inclusive Of Tie Wire Ga.#16) Iii.1 Reinforcing Steel (grade 40 ,fy=276 Mpa Inclusive Of Tie Wire Ga. #16) Kgs 11,927.54 Iii.2 Reinforcing Steel (grade 60 ,fy=414 Mpa Inclusive Of Tie Wire Ga. #16) Kgs 13,173.54 Iv Formworks And Scaffoldings Second Floor Iv.1 Column Sq.m 144 Iv.2 Roof Beam Sq.m 284 Iv.3 Lintel Beam Sq.m 32 Iv.4 Stiffiner Column Sq.m 33 Iv.5 Stairs (stair 1 And 2) Sq.m 100 V. Masonry Works V.1 Second Floor V.1.1 Exterior Wall (6"chb 700 Psi Including 12mm Thk Plastering) Sq.m 173 V.1.2 Interior Wall (4"chb 700 Psi Including 12mm Thk Plastering) Sq.m 207 Vi Doors And Windows Second Floor Vi.1 Doors And Accessories Inclusive Of Painting Vi.1.1 D2 - 900mm Flush Door (single-acting Door) W/ View Window Set 4 Vi.1.2 D4 - 800mm Flush Door (single Acting Door) Set 4 Vi.1.3 D7 - 700mm Pvc Door (single Acting Door) Set 4 Vi.2 Windows With Accessories Vi.2.1 W1 - 4panels - Jalousie Window On Aluminum Frame Set 2 Vi.2.2 W2 - 2panels-jalousie Window On Aluminum Frame Set 4 Vi.2.3 W4 - 6mm Ordinary Glass - Transparent Fixed Glass Awning Window Incl. Framing Set 2 Vi.2.4 W5 - 6mm Ordinary Glass - Transparent Fixed Glass Awning Window Incl. Framing Set 1 Vi.2.5 W7 - 6mm Ordinary Glass - Transparent Fixed Glass Awning Window Incl. Framing Set 4 Vi.2.6 W10 - 6mm Ordinary Glass - Transparent Fixed Glass Awning Window Inc. Framing Set 3 Vii Finishes Vii.1 Floor Finishes Vii.1.1 Ground Floor Vii.1.1.1 300mm X 300mm Wall Tiles (comfort Room) Sq.m 62 Vii.1.2 Second Floor Vii.1.2.1 Ff01 - Smooth Concrete Cement Finish Including 100mm Concrete Topping Sq.m 186 Vii.1.2.2 Ff02 - 300mm X 300mm Non-slip Porcelain Tiles Sq.m 19 Vii.1.2.3 Ff03 - 600mm X 600mm Non-slip Porcelain Tiles Sq.m 126 Vii.1.2.4 300mm X 300mm Wall Tiles (comfort Room) Sq.m 55 Vi.2 Painting Works Vi.2.1 Ground Floor Vi.2.1.1 Interior Wall Top-coat Paint Finish Sq.m 250 Vi.2.1.2 Exterior Walls Including Corridor Ceiling Sq.m 509 Vi.2.1.3 Fiber Cement Board Ceiling Sq.m 237 Vi.2.2 Second Floor Vi.2.2.1 Exterior And Interior Walls Including Skim Coat Sq.m 810 Vi.2.2.2 Fiber Cement Board Ceiling (rooms And Hallway) Sq.m 286 Viii Carpentry Works Viii.1 Ceiling Works Viii.1.1 Ground Floor Viii.1.1.1 Cf01 - 3.5mm Thk Fiber Cement Board On Light Metal Framing Sq.m 186 Viii.1.2 Second Floor Viii.1.2.1 Cf01 - 3.5mm Thk Fiber Cement Board On Light Metal Framing Sq.m 234 Viii.1.2.2 Cf02 - Acoustic Board 2x4x5/8, Fine Fissured On Tee Runner Framing Sq.m 52 Viii.1.2.3 0.4mm Thk Pre-painted Metal Spandrel With Air Vent On Metal Framing Sq.m 149 Viii.2 Partition Works Viii.2.1 Foldable Partition Fabric Acoustic Sq.m 17 Ix Steel Works Ix.1 Roof Framing And Steel Trusses Ix.1.1 Steel Trusses Ix.1.1.1 2"x2"x1/4" Angle Bar Ln.m 481 Ix.1.1.2 1-1/2" X 1-1/2" X 3/16" Angle Bar Ln.m 582 Ix.1.2 C-purlins Ix.1.2.1 140mm X 41mm X 2.0mm C-purlins Ln.m 1076 Ix.1.3 Sag Rod Ix.1.3.1 12mm Dia. Plain Round Bars Ln.m 113 Ix.2 Pre-painted Roofing Including Bended Accessories Ix.2.1 0.50mm Long Span Pre-painted Ribbed Type, Red Color Gi Sheet Ln.m 536 Ix.2.2 0.50mm Bended Spanish Gutter (red) Ln.m 40 Ix.2.3 0.50mm Bended Gutter Flashing (red) Ln.m 40 Ix.2.4 0.50mm Bended End Flashing (red) Ln.m 108 Ix.2.5 0.50mm Metal Fascia Ln.m 108 Ix.2.6 1"x1"x4mm Fascia Frame Ln.m 108 Ix.2.7 Insulation Foam 10mm, Double Sided Sq.m 483 Ix.3 Stairs, Ramp And Second Floor Corridor Metal Railings Ix.3.1 Stainless Steel (304) Round Tube 50mm X 6mm X 1.5mm, Handrail Ln.m 242 Ix.3.2 Stainless Steel (304) Round Tube 50mm X 6mm X 1.5mm, Balusters Ln.m 83 Ix.3.3 Aluminum Stair Nosing 1 1/2 X 8ft. X 1.2mm Thick Ln.m 80 Ix.4 1-3/4" X 3" Aluminum Tubular Wood Finish Vertical Slots Ln.m 22 Ix.5 Green Wall Panel Unit 1 Ix.6 Glass Roof Canopy Unit 1 Ix.7 Stainless Steel Letters And Logo Unit 1 X Electrical Works X.1 Lighting Luminaries X.1.1 24w Led Lamp Panel Recessed Downlight, Round, Daylight, Glass Covered To Specialist Recommendation Set 22 X.1.2 15w Led Lamp Panel Recessed Downlight, Round, Daylight, Glass Covered To Specialist Recommendation Set 4 X.1.3 2x28w Led Fluorescent Lamp, Recessed 300x1200mm Daylight, Rectangular To Specialist Recommendation Set 18 X.1.4 Twin 7.5w Led Lamp, Self-contained For Non-maintained Emergency Lighting For 3 Hours Duration. Set 15 X.1.5 Exit Light Set 3 X.2 Wiring Devices X.2.1 Switch: Two Gang, 15a, 230v, Flush Mount Set 8 X.2.2 Switch: One Gang Three Way, 15a, 230v, Flush Mount Set 2 X.2.3 Convenience Outlet, Duplex, 16a, 230v W/ground, Wall Flush Mounted Set 22 X.2.4 Outlet, Single, 15a, 230v For Exhaust Fans, Ceiling Fans, Emergency Lightings, Exit Sign And Hand Dryers Set 7 X.2.5 Hand Dryer 240v, Single Phase, 1400watts Set 3 X.2.6 Junction Box: 100x100x60mm, Square, Galvanized, #16 W/cover Ea 100 X.2.7 Outlet Box: 50x100x60mm, Galvanized, #16 Ea 115 X.2.8 Pull Box: 200x250x100mm, Galvanized, #18 W/cover Ea 2 X.3 Wires And Cables X.3.1 2.0mm2 Tw Wire-green M 50 X.3.2 3.5mm2 Thw Cu-green M 500 X.3.3 3.5mm2 Thw Cu-white M 500 X.3.4 22mm2 Thhn-2 Wire (fr)-yellow M 15 X.3.5 22mm2 Thhn-2 Wire (fr)-blue M 15 X.3.6 22mm2 Thhn-2 Wire (fr)-red M 15 X.4 Conduits, Boxes & Fittings X.4.1 Conduit: 20mm Dia. X 300mm Pvc L 104 X.4.2 Elbow: 32mmdia.pvc, Elbow: 32mmdia. Emt, Adapter W/lock Nut: 20mmdia.pvc, Adapter W/lock Nut: 32mmdia.pvc, Angle Bars, Unistrut Channel, Lock Nuts And Bushing Nuts, Conduit Clamps, Expansion Bolts. Etc. L 1 Xi Plumbing Works Xi.1 Plumbing Fixtures And Accessories/fittings Xi.1.1 Two Piece Water Closet With Complete Accessories Units 4 Xi.1.2 Urinal With Complete Accessories Units 1 Xi.1.3 Wall Mounted Lavatory And Complete Accessories Units 3 Xi.1.4 6" Stainless Kitchen Sink With Complete Accessories (processing Room) Units 6 Xi.1.5 6" Stainless Floor Drain Units 4 Xi.2 Waterline Xi.2.1 Second Floor Xi.2.1.1 3/4" Ppr Pipe Pn20 Ln.m 20 Xi.2.1.2 1 - 1/4" Ppr Pipe Ln.m 19 Xi.2.1.3 Fittings And Accessories Lot 1 Xi.3 Sanitary & Waste Line Xi.3.1 Second Floor Xi.3.1.1 100mm Dia. Pvc Pipe, S-1000 Ln.m 18 Xi.3.1.2 75mm Dia. Pvc Pipe, S-1000 Ln.m 1 Xi.3.1.3 Fittings And Accessories Lot 1 Xi.3.2 Downspout Xi.3.2.1 100mm Dia. Pvc Pipe, S-1000 Ln.m 250 Xi.3.2.2 Fittings And Accessories Unit 1 Xi.4 Non Metallic Diaphragm Pressure Tank ( 450 Liters) Inclusive Of Tank Fittings And Accessories Set 1 Xi.5 1hp Booster Pump Unit 2 Xii Mechanical Works Xii.1 Fire Protection - Lpg Xii.1.1 Equipment And Devices Unit 1 Xii.1.2 Pipes And Fittings Xii.1.2.1 Gi Pipes Schedule 40 Astm Including Fittings Lot 1 Xii.1.2.2 Lpg Pipe Secondary Containment Lot 1 Xii.2 Fire Protection-automatic Fire Sprinkler System Xii.2.1 Automatic Fire Sprinkler System Unit 1 Xii.2.2 Bi Pipes - Schedule 40 Astm Including Valves And Fittings Lot 1 Xii.2.3 Brackets And Supports Lot 1 Xii.2.4 Valves - Ul/fm Approved Lot 1 Xii.2.5 Flow And Monitoring Switches Unit 1 Xii.2.6 Firehose Cabinet W/ Complete Accessories Unit 4 Xii.2.7 Fire Extinguisher Unit 10 Xii.2.8 Fire And Jockey Pumps Including Pump Accessories - Including All Necessary Materials And Accessories To Complete The System Set 1 Xii.3 Fire Reserve Tank (34 Cu.m) Including Waterproofing And Accessories Unit 1 Xii.4 Pumphouse Unit 1 Xiii Auxiliary Works Xiii.1 Fire Detection And Alarm System (fdas) Xiii.1.1 Fire Alarm Control Panel And Accessories Unit 1 Xiii.1.2 Wires, Cables And Metallic Conduits Lot 1 Xiii.1.3 Roughing-ins Lot 1 Xiii.1.4 Miscellaneous Lot 1 Xiii.1.5 Grounding And Bonding Lot 1
Closing Soon25 Nov 2024
Tender AmountPHP 14.4 Million (USD 244.2 K)
City Government Iligan Tender
Civil And Construction...+2Building Construction, Construction Material
Philippines
Details: Description Invitation To Bid The Iligan City Government Bids And Awards Committee (bac), Through Special Educational Fund Intend To Apply The Sum Of P 3,883,283.75 Being The Approved Budget For The Contract (abc) To Payments Under The Contract For Construction Of School Covered Court At Kalubihon High School, Brgy. Dalipuga, Iligan City With Project No. Cb(b)-24-132 (ceo-infra). Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. The Iligan City Government Bids And Awards Committee Now Invites For The Supply And Delivery Of Items Below-stated: Particulars Construction Of School Covered Court At Kalubihon High School, Brgy. Dalipuga, Iligan City • General Requirements *including Processing Of Permits & Clearances *installation Of Project Billboard, 2 Sets; *occupational Safety & Health Program; • Removal & Demolition Works *demolition Of An Existing Concrete Walkway; • Earthworks *excavation For Foundation & Tie Beam; *backfilling & Compaction; *gravel Bedding For Foundation; Tie Beam & Slab On Grade • Concrete Works , Forms & Scaffoldings *concrete Pouring For Foundation ,column, Tie Beam & Slab On Grade • Electrical Works *installation Of Electrical Wirings & Connections W/ Complete Accessories & Fixtures; • Steel Reinforcements *using 10mmø, 16mmø, 20mmøx 6m Deformed Steel Bars W/ #16 G.i. Tie Wire, For Foundation, Columns Tie Beams, Slab On Grade, Lateral Ties & Stirrups; • Steel Works *fabrication & Installation Of Steel Rafter, Steel Girt & Steel Collar (50mm X 50mm X 6mm Thk. & 38mm X 38mm X 6mm Thk. Angle Bar); *installation Of 2" X 4" X 1.20mm Thk. C-purlins W/ 10mmø Dsb Sagrods & 16mmø Dsb Cross Brace W/ Tumbuckle ; *fabrication & Installation Of Steel Ridge Girt (50mm X 50mm X 6mm Thk. & 38mm X 38mm X 4.5mm Thk. Angle Bar); *all Steel Rafter,girt, Collar, Ridge Girt, Fascia Frame, C-purlins Must Be Coat Of Epoxy Primer; *fabrication & Installation Of Steel Fascia Frame (25mm X 25mm X 4.0mm Thk. Angle Bar & 25mm X 4.0mm Thk. Flat Bar); *installation Also Of Base Plate And Must Be Full Weld On Steel Rafter At The Top Of The Column W/16mmø Anchor Bolt W/nut & Washer To Be Full Weld On Vertical Bars Of Columns; Gusset Plate For All Steel Joints On Trusses (web Members); • Tinsmithry Works *installation Of 0.40mm Thk. Long-span Colored Roof Rib Type,0.4mm Thk. Pre-fab Colored Ridge Roll, 0.30m X 2.30m X 0.4mm Thk . Pre-fab Colored Gutter,0.40mm Thk. Pre-fab Fascia Cap, 0.40mm Thk. Flashing Gutter /w Complete Accessories; I. Permits & Clearances (q = 1.00 Lumpsum) Includes Fire, Brgy. Clearance For Construction Fee, Professional Fee, White Print (a-3)-6 Sets Of Plans. Ii. Construction Safety & Health Program (q = 1.00 L.s.) Iii. Project Billboard (q = 2.00 Set/s) Includes 4' X 8' Tarpaulin Print Billboard, 8' X 8' Tarpaulin Print Billboard, 2"x 2"x 14' Coco Lumber, 2" X 2" X 10' Coco Lumber, 2" X 2" X 8' Coco Lumber, Assorted Sizes C.w. Nails. Iv. Mobilization & Demobilization (q = 1.00 Lot) V. Removal & Demolition Works (q = 1.00 Lot) Includes Removal Of An Existing Concrete Walkway. Vi. Earthworks (q = 123.13 Cu.m) Includes Volume To Be Excavated, Volume To Be Backfilled, Gravel Bedding (1-1/2"ø). Vii. Concrete Works, Formworks And Scaffoldings (q = 54.70 Cu.m) Includes Portland Cement, Washed Sand, Washed Gravel, 4' X 8' X 1/4" Thk. Marine Plywood, 2" X 3" X 10' Coco Lumber, Assorted Sizes C.w Nails. Viii. Steel Reinforcem Ents (q = 5,748.33 Kg/s) Includes 10mm Dia. X 6m Dsb, 16mm Dia. X 6m Dsb, 20mm Dia. X 6m Dsb, #16 G.i Tie Wire. Ix. Tinsmith Ry (q = 368.33 Sq.m) Includes 0.4mm Thk. Ga. #24 Long Span Rib Type, Pre-fab Colored Ridge Roll, 0.4mm Thk. X 8', Pre-fab Colored Fascia Cover (0.4mm Thk. X 8'), Blind Rivets (1000pcs/box), Teksrew, Riveter, Aviation Metal Snip Scissor. X. Steel Works (q = 9,202.10 Kg/s) Includes 50mm X 50mm X 6m X 6mm Thk. Angle Bar- 128pcs, 38mm X 38mm X 6m X 6mm Thk. Angle Bar- 159pcs, 38mm X 38mm X 6m X 4.5mm Thk. Angle Bar- 9pcs, 25mm X 25mm X 6m X 4.0mm Thk. Angle Bar- 26pcs, 25mm X 6m X 4.0mm Thk. Flat Bar- 10pcs, 2" X 4" X 6m X 1.2mm Thk. C-purlins- 96pcs, 4' X 8' X 10mm Thk. Mild Steel Plate, 16mmø X 6mm Dsb Cross Brace- 24pcs, 16mmø Turnbuckle, Sagrods-10mmø X 6mm Dsb- 45pcs, M16ø Anchor-bolt (w/ 5% Wastage), Nut & Washer (w/ 5% Wastage), Welding Rod (6011), Epoxy Primer, 4" Paint Brush, 4" Ø Cutting Disc, 4" Ø Grinding Disc, Assorted Sand Paper. Xi. Paint Works & Finishes (q = 337.84 Sq.m.) Includes Skim Coat (a = 67.84 Sq.m), Neutralizer, Flat Latex Primer, Masonry Putty, Top Coat (1st & 2nd Coat), Acreex Floor Coating (a = 270.00 Sq.m), Acreex Reducer, Baby Roller #4 Mini, Tray Paint, Paint Brush (2"), Sand Paper. Xii. Electrical Works (q = 1.00 Lot) Includes Pvc Conduit Pipe, 3m X 1/2"inner Diameter; Pvc Conduit Pipe, 3m X 1"inner Diameter; Pvc Conduits Coupling (15mm Inner Ø); Pvc Conduit Elbow 90 Deg, (15mm Inner Ø); Pvc Conduit Elbow 90 Deg, (25mm Inner Ø); Pvc Male Adapter W/locknut (15mm Inner Ø); Pvc Corrugated Electrical Flexible Hose, 1/2" X 100meters/roll; Pvc Junction Box (octagon Shape) Depth Type W/cover & Screws 4" X 4" X 2"; Utility Box, 2" X 4" Pvc Depth Type W/cover; Tie Wire/g.i Wire, Gauge #16 (per Kilo); Electrical Tape; Pvc Clamp Clip For Pipes & Flexible Hose, 15mm, 100pcs/bag; Ufo Led High Bay 100w Smd Slim Type Black Daylight, 1100 Lm-12pcs; Electric Wires, Thhn Type. 3.50mm2 . Copper Wire: Electric Wires. Thhn Type. 14.0mm2 , Copper Wire: 2-gang Outlet, 3 Prong, Gfci, 240v; Panel Board Box, 2 Pole Bolt-on W/main Breaker, 6 Branches; Circuit Breaker, Bolt-on Screw Type Terminal, 15amp, 2 Poles/single Phase; Circuit Breaker, Bolt-on Screw Type Terminal, 20amp, 2 Poles/single Phase; Circuit Breaker, Bolt-on Screw Type Terminal, 60amp, 2 Poles/single Phase; Service Entrance Cap "/electrical Weather Cap/ Service Head/ Weatherproof Cap; Secondary Rack Heavy Duty, 2-pole W/spool Insulator & Screws; Cable Tiles (nylon), Size 150mm/100pcs Per Pack; Ground Rpd 5/8 X 4.75feet 5ft Copper Plated With Ground Clamp. Approved Budget For The Contract (abc): P 3,883,283.75 Required Bid Security: 2% Of The Abc If Cash, Manager’s Check; Bank Draft/guarantee, Irrevocable Letter Of Credit Confirmed Or Authenticated By A Universal Or Commercial Bank; And 5% Of The Abc If Surety Bond Callable Upon Demand Issued By A Surety Or Insurance Company Duly Certified By The Insurance Commission As Authorized To Issue Such Security Delivery Period Is Within One Hundred Forty-five (145) Calendar Days From Receipt Of Notice To Proceed. Bidders Should Have Completed, Within Five (5) Years From The Date Of Submission And Receipt Of Bids, A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii. Instruction To Bidders. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using A Non-discretionary “pass/fail” Criterion As Specified In The Implementing Rules And Regulations (irr) Of Republic Act (ra) 9184, Otherwise Known As The “government Procurement Reform Act”. Bidding Is Restricted To Filipino Citizens/sole Proprietorships, Partnerships, Or Organizations With At Least Sixty Percent (60%) Interest Or Outstanding Capital Stock Belonging To Citizens Of The Philippines, And To Citizens Or Organizations Of A Country The Laws Or Regulations Of Which Grant Similar Rights Or Privileges To Filipino Citizens, Pursuant To Ra 5183 And Subject To Commonwealth Act 138. Interested Bidders May Obtain Further Information From Iligan City Government And Inspect The Bidding Documents During Office Hours From 8:00 A.m. – 12:00 P.m. And 1:00 P.m. – 5:00 P.m. At The Office Of The Bids And Awards Committee, Room 205, Left Wing, 2nd Floor, Sp Bldg., Buhanginan Hills, Palao, Iligan City. The Complete Schedule Of Activities Is Listed, As Follows: Activities Schedule 1.issuance Of Bid Documents: November 12 – December 3, 2024 – 8:00 A.m. At Room 205, Left Wing, 2nd Floor, Sp Bldg., Buhanginan Hills, Palao, Iligan City. 2.pre-bid Conference: November 19, 2024 – 9:30 A.m. At Casimero P. Cabigon Hall, 2nd Floor City Hall Main Bldg., Buhanginan Hills, Pala-o, Iligan City 3.submission Of Bids: December 3, 2024 – 9:30 A.m. At Casimero P. Cabigon Hall, 2nd Floor City Hall Main Bldg., Buhanginan Hills, Pala-o, Iligan City 4.opening Of Bids: December 3, 2024 – 9:30 A.m. At Casimero P. Cabigon Hall, 2nd Floor City Hall Main Bldg., Buhanginan Hills, Pala-o, Iligan City A Complete Set Of Bidding Documents Will Be Available To Prospective Bidders Upon Payment Of A Non-refundable Amount Of P 5,000.00 To The Iligan City Government Cashier, At The Bac Office, 2nd Floor, City Hall Main Building, Buhanginan Hills, Pala-o, Iligan City. The Iligan City Government Reserves The Right To Accept Or Reject Any Bid, To Annul The Bidding Process, And To Reject All Bids At Any Time Prior To Contract Award, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. Furthermore, The City Government Of Iligan Assumes No Responsibility Whatsoever To Compensate Or Indemnify Bidders For Any Expense Or Loss Incurred In The Preparation And Submission Of The Eligibility Statements And Bids. Approved By: (signed)darwin J. Manubag, Phd. Bac Chairman Date Of Advertisement/posting: November 12, 2024 Place Of Posting/advertisement: City Hall/ibjt Bulletin Boards, Iligan Official Website, Phil-geps Itb No. 24-132(ceo-infra)
Closing Date3 Dec 2024
Tender AmountPHP 3.8 Million (USD 65.8 K)
Stadt Brandenburg An Der Havel, Der Oberb rgermeister, Tiefbauamt, SG 66 1 Stra en Und Br cken Tender
Civil And Construction...+1Road Construction
Germany
Details: Road construction and electrical work: 830 m² asphalt milling; 830 m² concrete pavement breaking up; 630 m² concrete base layer C 25/30, 20 cm thick; 200 m² paving from concrete paving; 100 Ifm curbs laid from concrete; 240 Ifm retaining wall made from concrete; 50 Ifm galvanized railings made; 630 m² asphalt base layer made from Ac 32 Ts; 630 m² asphalt binder course made from Ac 16 Bs Sg; 8 pieces of street lighting including cable laying; 50 m drainage pipe laid.
Closing Date10 Dec 2024
Tender AmountRefer Documents
Municipality Of Kalibo, Aklan Tender
Electronics Equipment...+2Security and Emergency Services, Electrical and Electronics
Philippines
Details: Description Republic Of The Philippines Province Of Aklan Municipality Of Kalibo Invitation To Bid For Purchase And Installation Of Surveillance And Multi-emergency Monitoring System With Dvrs, Peripherals And Led Monitoring Banks Use At Mdrrm, Kalibo, Aklan The Municipality Of Kalibo, Through The Trust Fund Intends To Apply The Sum Of One Million Pesos (php1,000,000.00) Being The Abc To Payments Under The Contract For Purchase And Installation Of Surveillance And Multi-emergency Monitoring System With Dvrs, Peripherals And Led Monitoring Banks Use At Municipal Disaster Risk Reduction Management Office, Kalibo, Aklan With Identification Number 10-012-1566-24. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. Item Description Unit Quantity 1 55 Inch 2x2 Video Wall Sets 4 55” Fhd Video Wall Display Unit (ultra Narrow Bezel 3.5mm) > Industrial Level Ads Lcd Panel, Suitable For Continues 24h/7 Operation > Ultra-narrow 3.5mm Bezel-to-bezel Design> > Anti-glare Panel, Vivid And Memorable Image Quality > Factory Calibration Technology For High Color Uniformity > Built-in 3d Noise Reduction System And Picture Splicing Function > Hdmi, Dvi, Vga, Bnc, Usb, Supporting Hdmi Daisy Chain Display Diagonal Size: 55” (16:9) Panel Type: Ads Resolution: 1920x1080 (fhd) Bezel Width: 2.3mm (t/l), 1.2mm (b/r) Backlight Direct Led Brightness: 500 Cd/m² Contrast Ratio: 1200:1 Pixel Density: 40dpi Viewing Angle: H178°, V178” Response Time (g-to-g): 8ms Color Depth: 8bit (16.7m) Color Temperature” 10,000k Surface Treatment Haze: 25%, 3h Mtbf: 50,000h Input Cvbs(bnc)x1, Vga(d-sub)x1, Dvi-dx1, Hdmix1, Rs232x1, Usbx2, Audiox1, Irx1outputcvbs(bnc)x1, Rs232x1, Hdmix2, Vgax1, Audio X1 Power Consumption: 175w Power Consumption: (max)195w Including The Following Accessories Floor-standing Pedestal, Hdmi 15m 2 Ip Paging Microphone Touch Screen Hd Pc. 1 Gooseneck Mic Touch Screen 4 Inch Display Monitor Power Supply Dc 12v/1.5a S/n (signal-to-noise) Ratio ≥80db Audio Sampling & Bit Rate 8khz-44. 1khz, 16bit, 8kbps-320kbps Audio Sampling Rate 8khz-22.05khz, 16bit Frequency Response 100hz~16khz Network Protocol Sip (rfc 3261), Http, Tcp/ip, Udp, Arp, Icmp, Igmp, Ftp Configuration Method Local Settings/web Page Mounting Interface 1xrj45 Ethernet Port, 1xusb 2.0, 2xline Input, 1xline Output, 1xrelay Input, 1x Mic Input, 1xpower Supply Port Dimensions 144x144x34mm Weight 0.55kg Standard Accessories 1 X Microphone Rod, 1x Terminal Block Connector, 1 X Installation Manual, 1x Certification Optional Accessories Dc 12v/1.5a Power Adapter (us/eu/uk/au) With Built In Software License For Ip Speakers 3 Labor, Installation, Configuration, Testing Lot 1 Commissioning Etc *scope Of Work: Labor And Professional Services For The Installation And Configuration, Testing And Commissioning Of Gpon Technology System Integration, Network Base Public Address Software Integration, Video Wall Materials And Brackets, Video Wall Decoder Controller, Splicing, Termination, Optical Network Devices Installation And Configuration Hdmi Cables, And Operator Pc Software Installation And Configuration Door *installation Includes *warranty: -provide A 2-year Warranty On All Installed Equipment, Video Wall The Municipality Of Kalibo Now Invites Bids For The Above Procurement Project. Delivery Of The Goods Is Required Within Fifteen (15) Days Upon Receipt Of Notice To Proceed. Bidders Should Have Completed, Within Two (2) Years From The Date Of Submission And Receipt Of Bids, A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii (instructions To Bidders). Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using A Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) No. 9184. Bidding Is Restricted To Filipino Citizens/sole Proprietorships, Partnerships, Or Organizations With At Least Sixty Percent (60%) Interest Or Outstanding Capital Stock Belonging To Citizens Of The Philippines, And To Citizens Or Organizations Of A Country The Laws Or Regulations Of Which Grant Similar Rights Or Privileges To Filipino Citizens, Pursuant To Ra No. 5183. Prospective Bidders May Obtain Further Information From Municipality Of Kalibo And Inspect The Bidding Documents At The Address Given Below During 8:00 -12:00 A.m. And 1:00 – 5:00 P.m., Except Saturdays, Sundays & Holidays. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders On November 11 – December 2, 2024 From The Given Address And Website(s) Below And Upon Payment Of The Applicable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb, In The Amount Of One Thousand Pesos (php1,000.00). The Procuring Entity Shall Allow The Bidder To Present Its Proof Of Payment For The Fees In Person. The Municipality Of Kalibo Will Hold A Pre-bid Conference On November 18, 2024; 9:00 A.m. At 2nd Floor Municipal Conference Hall, Old Building, Kalibo, Aklan. Bids Must Be Duly Received By The Bac Secretariat Through Manual Submission At The Office Address Indicated Below On Or Before 9:00 A.m. Of December 2, 2024. Late Bids Shall Not Be Accepted. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 14. Bid Opening Shall Be On December 2, 2024; 9:30 A.m. At 2nd Floor, Municipal Conference Hall, Old Building, Kalibo, Aklan. Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend The Activity. The Municipality Of Kalibo Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Irr Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. For Further Information, Please Refer To: Leah E. Yarre Bac – Secretariat Telephone Number (036) 268-4436 You May Visit The Website: For Downloading Of Bidding Documents: Www.kaliboaklan.gov.ph Sgd: Leenard M. Cristobal Bac, Vice-chairperson
Closing Date2 Dec 2024
Tender AmountPHP 1 Million (USD 16.9 K)
Municipality Of Badiangan, Iloilo Tender
Civil And Construction...+1Civil Works Others
Philippines
Details: Description Section Ii. Instructions To Bidders A. General 1. Scope Of Bid 1.1 The Procuring Entity Named In The Bds Invites Bids For The Supply And Delivery Of The Goods As Described In Section Vii. Technical Specifications. 1.2 The Name, Identification, And Number Of Lots Specific To This Bidding Are Provided In The Bds. The Contracting Strategy And Basis Of Evaluation Of Lots Is Described In Itb Clause 28. 2. Source Of Funds The Procuring Entity Has A Budget Or Has Received Funds From The Funding Source Named In The Bds, And In The Amount Indicated In The Bds. It Intends To Apply Part Of The Funds Received For The Project, As Defined In The Bds, To Cover Eligible Payments Under The Contract. 3. Corrupt, Fraudulent, Collusive, And Coercive Practices 3.1 Unless Otherwise Specified In The Bds, The Procuring Entity As Well As The Bidders And Suppliers Shall Observe The Highest Standard Of Ethics During The Procurement And Execution Of The Contract. In Pursuance Of This Policy, The Procuring Entity: (a) Defines, For Purposes Of This Provision, The Terms Set Forth Below As Follows (i) “corrupt Practice” Means Behavior On The Part Of Officials In The Public Or Private Sectors By Which They Improperly And Unlawfully Enrich Themselves, Others, Or Induce Others To Do So, By Misusing The Position In Which They Are Placed, And Includes The Offering, Giving, Receiving, Or Soliciting Of Anything Of Value To Influence The Action Of Any Such Official In The Procurement Process Or In Contract Execution; Entering, On Behalf Of The Government, Into Any Contract Or Transaction Manifestly And Grossly Disadvantageous To The Same, Whether Or Not The Public Officer Profited Or Will Profit Thereby, And Similar Acts As Provided In Ra 3019; (ii) “fraudulent Practice” Means A Misrepresentation Of Facts In Order To Influence A Procurement Process Or The Execution Of A Contract To The Detriment Of The Procuring Entity, And Includes Collusive Practices Among Bidders (prior To Or After Bid Submission) Designed To Establish Bid Prices At Artificial, Non-competitive Levels And To Deprive The Procuring Entity Of The Benefits Of Free And Open Competition. (iii) “collusive Practices” Means A Scheme Or Arrangement Between Two Or More Bidders, With Or Without The Knowledge Of The Procuring Entity, Designed To Establish Bid Prices At Artificial, Non-competitive Levels. (iv) “coercive Practices” Means Harming Or Threatening To Harm, Directly Or Indirectly, Persons, Or Their Property To Influence Their Participation In A Procurement Process, Or Affect The Execution Of A Contract; (v) “obstructive Practice” Is (aa) Deliberately Destroying, Falsifying, Altering Or Concealing Of Evidence Material To An Administrative Proceedings Or Investigation Or Making False Statements To Investigators In Order To Materially Impede An Administrative Proceedings Or Investigation Of The Procuring Entity Or Any Foreign Government/foreign Or International Financing Institution Into Allegations Of A Corrupt, Fraudulent, Coercive Or Intimidating Any Party To Prevent It From Disclosing Its Knowledge Of Matters Relevant To The Administrative Proceedings Or Investigation Or From Pursuing Such Proceedings Or Investigation; Or (bb) Acts Intended To Materially Impede The Exercise Of The Inspection And Audit Rights Of The Procuring Entity Or Any Foreign Government/foreign Or International Financing Institution Herein. (b) Will Reject A Proposal For Award If It Determines That The Bidder Recommended For Award Has Engaged In Any Of The Practices Mentioned In This Clause For Purposes Of Competing For The Contract. 3.2 Further, The Procuring Entity Will Seek To Impose The Maximum Civil, Administrative, And/or Criminal Penalties Available Under Applicable Laws On Individuals And Organizations Deemed To Be Involved In Any Of The Practices Mentioned In Itb Clause 3.1(a). 3.3 Furthermore, The Funding Source And The Procuring Entity Reserve The Right To Inspect And Audit Records And Accounts Of A Bidder Or Supplier In The Bidding For And Performance Of A Contract Themselves Or Through Independent Auditors As Reflected In The Gcc Clause 3. 4. Conflict Of Interest 4.1 All Bidders Found To Have Conflicting Interests Shall Be Disqualified To Participate In The Procurement At Hand, Without Prejudice To The Imposition Of Appropriate Administrative, Civil, And Criminal Sanctions. A Bidder May Be Considered To Have Conflicting Interests With Another Bidder In Any Of The Events Described In Paragraphs (a) Through (c) Below And A General Conflict Of Interest In Any Of The Circumstances Set Out In Paragraphs (d) Through (f) Below: (a) A Bidder Has Controlling Shareholders In Common With Another Bidder; (b) A Bidder Receives Or Has Received Any Direct Or Indirect Subsidy From Any Other Bidder; (c) A Bidder Has The Same Legal Representative As That Of Another Bidder For Purposes Of This Bid; (d) A Bidder Has A Relationship, Directly Or Through Third Parties, That Puts Them In A Position To Have Access To Information About Or Influence On The Bid Of Another Bidder Or Influence The Decisions Of The Procuring Entity Regarding This Bidding Process. This Will Include A Firm Or An Organization Who Lends, Or Temporarily Seconds, Its Personnel To Firms Or Organizations Which Are Engaged In Consulting Services For The Preparation Related To Procurement For Or Implementation Of The Project If The Personnel Would Be Involved In Any Capacity On The Same Project; (e) A Bidder Submits More Than One Bid In This Bidding Process. However, This Does Not Limit The Participation Of Subcontractors In More Than One Bid; Or (f) (g) A Bidder Who Participated As A Consultant In The Preparation Of The Design Or Technical Specifications Of The Goods And Related Services That Are The Subject Of The Bid. A Bidder Who Lends, Or Temporarily Seconds, Its Personnel To Firms Or Organizations Which Are Engaged In Consulting Services For The Preparation Related To Procurement Or Implementation Of The Project, If The Personnel Would Be Involved In Any Capacity On The Same Project. 4.2 In Accordance With Section 47 Of The Irr Of Ra 9184, All Bidding Documents Shall Be Accompanied By A Sworn Affidavit Of The Bidder That It Is Not Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), Members Of The Technical Working Group (twg), Members Of The Bac Secretariat, The Head Of The Project Management Office (pmo) Or The End-user Unit, And The Project Consultants, By Consanguinity Or Affinity Up To The Third Civil Degree. On The Part Of The Bidder, This Clause Shall Apply To The Following Persons: (a) If The Bidder Is An Individual Or A Sole Proprietorship, To The Bidder Himself; (b) If The Bidder Is A Partnership, To All Its Officers And Members; (c) (d) If The Bidder Is A Corporation, To All Its Officers, Directors, And Controlling Stockholders; And If The Bidder Is A Cooperative, To All Its Officers, Directors And Controlling Share Holders Or Members; And (e) If The Bidder Is A Joint Venture (jv), The Provisions Of Items (a), (b), Or (c) Of This Clause Shall Correspondingly Apply To Each Of The Members Of The Said Jv, As May Be Appropriate Relationship Of The Nature Described Above Or Failure To Comply With This Clause Will Result In The Automatic Disqualification Of A Bidder. 5. Eligible Bidders 5.1 Unless Otherwise Indicated In The Bds, The Following Persons Shall Be Eligible To Participate In This Bidding: (a) Duly Licensed Filipino Citizens/sole Proprietorships; (b) Partnerships Duly Organized Under The Laws Of The Philippines And Of Which At Least Sixty Percent (60%) Of The Interest Belongs To Citizens Of The Philippines; (c) Corporations Duly Organized Under The Laws Of The Philippines, And Of Which At Least Sixty Percent (60%) Of The Outstanding Capital Stock Belongs To Citizens Of The Philippines; (d) Cooperatives Duly Organized Under The Laws Of The Philippines, And Of Which At Least Sixty Percent (60%) Of The Interest Belongs To Citizens Of The Philippines; And (e) Persons/entities Forming Themselves Into A Jv, I.e., A Group Of Two (2) Or More Persons/entities That Intend To Be Jointly And Severally Responsible Or Liable For A Particular Contract: Provided, However, That Filipino Ownership Or Interest Of The Joint Venture Concerned Shall Be At Least Sixty Percent (60%). 5.2 Foreign Bidders May Be Eligible To Participate When Any Of The Following Circumstances Exist, As Specified In The Bds. (a) When A Treaty Or International Or Executive Agreement As Provided In Section 4 Of The Ra 9184 And Its Irr Allow Foreign Bidders To Participate; (b) Citizens, Corporations, Or Associations Of A Country, Included In The List Issued By The Gppb, The Laws Or Regulations Of Which Grant Reciprocal Rights Or Privileges To Citizens, Corporations, Or Associations Of The Philippines; (c) When The Goods Sought To Be Procured Are Not Available From Local Suppliers; Or (d) When There Is A Need To Prevent Situations That Defeat Competition Or Restrain Trade. 5.3 Government Owned Or Controlled Corporations (goccs) May Be Eligible To Participate Only If They Can Establish That They (a) Are Legally And Financially Autonomous, (b) Operate Under Commercial Law, And (c) Are Not Attached Agencies Of The Procuring Entity. 5.4 Unless Otherwise Provided In The Bds, The Bidder Must Have Completed A Single Largest Completed Contract (slcc) Similar To The Project The Value Of Which, Adjusted If Necessary, By The Bidder To Current Prices Using The Philippine Statistics Authority (psa) Consumer Price Index, Must Be At Least Equivalent To A Percentage Of The Abc Stated In The Bds. For This Purpose, Contracts Similar To The Project Shall Be Those Described In The Bds, And Completed Within The Relevant Period Stated In The Invitation To Bid And Itb Clause 12.1(a)(ii). 5.5 Unless Otherwise Provided In The Bds, The Bidder Must Submit A Computation Of Its Net Financial Contracting Capacity (nfcc) Which Must Be At Least Equal To The Abc To Be Bid, Calculated As Follows: Nfcc = [(current Assets Minus Current Liabilities) (k)] Minus The Value Of All Outstanding Or Uncompleted Portions Of The Projects Under Ongoing Contracts, Including Awarded Contracts Yet To Be Started Coinciding With The Contract To Be Bid. Where: K = 15 The Values Of The Bidder’s Current Assets And Current Liabilities Shall Be Based On The Latest Audited Financial Statements Submitted To The Bir, Through Its Electronic Filling And Payment System (efps). If The Prospective Bidder Opts To Submit A Committed Line Of Credit (clc), It Must Be At Least Equal To Ten Percent (10%) Of The Abc To Be Bid And Issued By Auniversal Or Commercial Bank. 6. Bidders Responsibilities 6.1 The Bidder Or Its Duly Authorized Representative Shall Submit A Sworn Statement In The Form Prescribed In Section Viii – Bidding Forms As Required In Itb Clause 12.1(b)(iv). 6.2 The Bidder Is Responsible For The Following: (a) Having Taken Steps To Carefully Examine All Of The Bidding Documents; (b) Having Acknowledged All Conditions, Local Or Otherwise, Affecting The Implementation Of The Contract; (c) Having Made An Estimate Of The Facilities Available And Needed For The Contract To Be Bid, If Any; And (d) Having Complied With Its Responsibility To Inquire Or Secure Supplemental/bid Bulletin(s) As Provided Under Itb Clause 10.4; (e) Ensuring That It Is Not “blacklisted” Or Barred From Bidding By The Gop Or Any Of Its Agencies, Offices, Corporations, Or Lgus, Including Foreign Government/foreign Or International Financing Institution Whose Blacklisting Rules Have Been Recognized By The Gppb, By Itself Or By Relation, Membership, Association, Affiliation, Or Controlling Interest With Another Blacklisted Person Or Entity As Defined And Provided For In The Uniform Guidelines On Blacklisting. (f) Ensuring That Each Of The Documents Submitted In Satisfaction Of The Bidding Requirements Is An Authentic Copy Of The Original, Complete, And All Statements And Information Provided Therein Are True And Correct; (g) Authorizing The Head Of The Procuring Entity Or Its Duly Authorized Representative/s To Verify All The Documents Submitted; (h) Ensuring That The Signatory Is The Duly Authorized Representative Of The Bidder, And Granted Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary And/or To Represent The Bidder In The Bidding, With The Duly Notarized Secretary’s Certificate Attesting To Such Fact, If The Bidder Is A Corporation, Partnership, Cooperative, Or Joint Venture; (i) Complying With The Disclosure Provision Under Section 47 Of Ra 9184 In Relation To Other Provisions Of Ra 3019; And (j) (k) (l) Complying With Existing Labor Laws And Standards, In The Case Of Procurement Of Services Ensuring That It Did Not Give Or Pay Directly Or Indirectly, Any Commission, Amount, Fee, Or Any Form Of Consideration, Pecuniary Or Otherwise, To Any Person Of Official, Personnel Or Representative Of The Government In Relation To Any Procurement Project Or Activity. In Case Advance Payment Was Made Or Given, Failure To Perform Or Deliver Any Of The Obligations And Undertakings In The Contract Shall Be Sufficient Grounds To Constitute Criminal Liability For Swindling (estafa) Or The Commission Of Fraud With Unfaithfulness Or Abuse Of Confidence Through Misappropriating Or Converting Any Payment Received By A Person Or Entity Under An Obligation Involving The Duty To Deliver Certain Goods Or Services, To The Prejudice Of The Public And The Government Of The Philippines Pursuant To Article 315 Of Act No. 3815 S. 1930, As Amended, Or The Revised Penal Code. Failure To Observe Any Of The Above Responsibilities Shall Be At The Risk Of The Bidder Concerned. 6.3 The Bidder Is Expected To Examine All Instructions, Forms, Terms, And Specifications In The Bidding Documents. Unless Otherwise Indicated In The Bds, Failure To Furnish All Information Or Documentation Required In The Bidding Documents Shall Result In The Rejection Of The Bid And The Disqualification Of The Bidder. 6.4 It Shall Be The Sole Responsibility Of The Bidder To Determine And To Satisfy Itself By Such Means As It Considers Necessary Or Desirable As To All Matters Pertaining To The Contract To Be Bid, Including: (a) The Location And The Nature Of This Project; (b) Climatic Conditions; (c) Transportation Facilities; And (d) Other Factors That May Affect The Cost, Duration, And Execution Or Implementation Of This Project. 6.5 The Procuring Entity Shall Not Assume Any Responsibility Regarding Erroneous Interpretations Or Conclusions By The Prospective Or Eligible Bidder Out Of The Data Furnished By The Procuring Entity. However, The Procuring Entity Shall Ensure That All Information In The Bidding Documents, Including Bid/supplemental Bid Bulletin/s Issued, Are Correct And Consistent. 6.6 The Bidder Shall Bear All Costs Associated With The Preparation And Submission Of His Bid, And The Procuring Entity Will In No Case Be Responsible Or Liable For Those Costs, Regardless Of The Conduct Or Outcome Of The Bidding Process. 6.7 Before Submitting Their Bids, The Bidder Is Deemed To Have Become Familiar With All Existing Laws, Decrees, Ordinances, Acts And Regulations Of The Philippines Which May Affect This Project In Any Way. 6.8 The Bidder Should Note That The Procuring Entity Will Accept Bids Only From Those That Have Paid The Non-refundable Fee For The Bidding Documents At The Office Indicated In The Invitation To Bid. 7. Origin Of Goods And Services Unless Otherwise Indicated In The Bds, There Is No Restriction On The Origin Of Goods Other Than Those Prohibited By A Decision Of The United Nations Security Council Taken Under Chapter Vii Of The Charter Of The United Nations, Subject To Itb Clause 27.1. 8. Subcontracts 8.1 Unless Otherwise Specified In The Bds, The Bidder May Subcontract Portions Of The Goods To An Extent As May Be Approved By The Procuring Entity And Stated In The Bds. However, Subcontracting Of Any Portion Shall Not Relieve The Bidder From Any Liability Or Obligation That May Arise From The Contract For This Project. 8.2 Subcontractors Must Comply With The Eligibility Criteria And The Documentary Requirements Specified In The Bds. In The Event That Any Subcontractor Is Found By The Procuring Entity To Be Ineligible, The Subcontracting Of Such Portion Of The Goods Shall Be Disallowed. 8.3 The Bidder May Identify The Subcontractor To Whom A Portion Of The Goods Will Be Subcontracted At Any Stage Of The Bidding Process Or During Contract Implementation. If The Bidder Opts To Disclose The Name Of The Subcontractor During Bid Submission, The Bidder Shall Include The Required Documents As Part Of The Technical Component Of Its Bid. B. Contents Of The Bidding Documents 9. Pre-bid Conference 9.1 If So Specified In The Bds, A Pre-bid Conference Shall Be Held At The Venue And On The Date Indicated Therein, To Clarify And Address The Bidders’ Questions On The Technical And Financial Components Of This Project. 9.2 Bidders Are Encouraged To Attend The Pre-bid Conference To Ensure That They Fully Understand The Procuring Entity’s Requirements. Non-attendance Of The Bidder Will In No Way Prejudice Its Bid; However, The Bidder Is Expected To Know The Changes And/or Amendments To The Bidding Documents Discussed During The Pre-bid Conference. 9.3 Any Statement Made At The Pre-bid Conference Shall Not Modify The Terms Of The Bidding Documents Unless Such Statement Is Specifically Identified In Writing As An Amendment Thereto And Issued As A Supplemental/bid Bulletin. 10. Clarification And Amendment Of Bidding Documents 10.1 Bidders Who Have Purchased The Bidding Documents May Request For Clarifications On Any Part Of The Bidding Documents For An Interpretation. Such A Request Must Be In Writing And Submitted To The Procuring Entity At The Address Indicated In The Bds At Least Ten (10) Calendar Days Before The Deadline Set For The Submission And Receipt Of Bids. 10.2 Supplemental/bid Bulletins May Be Issued Upon The Procuring Entity’s Initiative For Purposes Of Clarifying Or Modifying Any Provision Of The Bidding Documents Not Later Than Seven (7) Calendar Days Before The Deadline For The Submission And Receipt Of Bids. Any Modification To The Bidding Documents Shall Be Identified As An Amendment. 10.3 Any Supplemental/bid Bulletin Issued By The Bac Shall Also Be Posted On The Philippine Government Electronic Procurement System (philgeps) And The Website Of The Procuring Entity Concerned, If Available. It Shall Be The Responsibility Of All Bidders Who Secure The Bidding Documents To Inquire And Secure Supplemental/bid Bulletins That May Be Issued By The Bac. However, Bidders Who Have Submitted Bids Before The Issuance Of The Supplemental/bid Bulletin Must Be Informed And Allowed To Modify Or Withdraw Their Bids In Accordance With Itb Clause 23. C. Preparation Of Bids 11. Language Of Bids The Bid, As Well As All Correspondence And Documents Relating To The Bid Exchanged By The Bidder And The Procuring Entity, Shall Be Written In English. Supporting Documents And Printed Literature Furnished By The Bidder May Be In Another Language Provided They Are Accompanied By An Accurate Translation In English Certified By The Appropriate Embassy Or Consulate In The Philippines, In Which Case The English Translation Shall Govern For Purposes Of Interpretation Of The Bid. 12. Documents Comprising The Bid: Eligibility And Technical Components. 12.1 Unless Otherwise Indicated In The Bds, The First Envelope Shall Contain The Following Eligibility And Technical Documents: (a) Eligibility Documents - Class "a" Documents: (i) Philgeps Platinum Certificate Of Registration And Membership With Annex A In Accordance With Section 8.5.2 Of The Irr. (ii) Statement Of All Its Ongoing Government And Private Contracts Within The Period Stated In The Bds, Including Contracts Awarded But Not Yet Started, If Any. Statement Of The Bidder's Single Largest Completed Contract (slcc) Similar To The Contract To Be Bid, In Accordance With Itb Clause 5.4, Within The Relevant Period As Provided In The Bds. The Two Statements Required Shall Indicate For Each Contract The Following: (ii.1) Name Of The Contract; (ii.2) Date Of The Contract; (ii.3) Contract Duration; (ii.4) Owner's Name And Address; (ii.5) Kinds Of Goods; (ii.6) (ii.7) (ii.8) (ii.9) For Statement Of Ongoing Contracts- Amount Of Contract And Value Of Outstanding Contracts; For Statement Of Slcc-amount Of Completed Contracts, Adjusted By The Bidder To Current Prices Using Psa's Consumer Price Index, If Necessary For The Purpose Of Meeting The Slcc Requirement; Date Of Delivery; And End User's Acceptance Or Official Receipt(s) Or Sales Invoice Issued For The Contract, If Completed, Which Shall Be Attached To The Statements. (iii) The Prospective Bidder’s Computation Of Its Net Financial Contracting Capacity (nfcc) Which Must Be At Least Equal To The Abc To Be Bid, Calculated As Follows: Nfcc = [(current Assets Minus Current Liabilities) (k)] Minus The Value Of All Outstanding Or Uncompleted Portions Of The Projects Under Ongoing Contracts, Including Awarded Contracts Yet To Be Started Coinciding With The Contract To Be Bid. Where: K = 15 The Values Of The Bidder’s Current Assets And Current Liabilities Shall Be Based On The Data Submitted To The Bir, Through Its Electronic Filling And Payment System (efps). Or A Committed Line Of Credit From A Universal Or Commercial Bank (not Applicable To Procurement Of Infrastructure Projects) Class "b" Document: (iv) If Applicable, The Jva In Case The Joint Venture Is Already In Existence, Or Duly Notarized Statements From All The Potential Joint Venture Partners Stating That They Will Enter Into And Abide By The Provisions Of The Jva In The Instance That The Bid Is Successful. (b) Technical Documents - (i) Bid Security In Accordance With Itb Clause 18. If The Procuring Entity Requires The Bidders To Submit The Bid Security In The Form Of: (i.1) Cash Or Cashier’s/ Manager’s Check, Issued By A Universal Or Commercial Bank; Or (i.2) A Bank Draft/guarantee Or An Irrevocable Letter Of Credit Issued By A Universal/ Commercial Bank, It Shall Be Accompanied By A Confirmation From A Universal Or Commercial Bank, If Issued By A Foreign Bank; Or (i.3) (i.4) A Surety Bond Accompanied By A Certification Coming From An Authorized Insurance Commission That A Surety Or Insurance Company Is Authorized To Issue Such Instrument; Bid Securing Declaration (ii) (iii) Statement Of Compliance To The Schedule Of Requirements Conformity With Technical Specifications, As Enumerated And Specified In Sections Vi And Vii Of The Bidding Documents; And (iv) Sworn Statement In Accordance With Section 25.2(a)(iv) Of The Irr Of Ra 9184 And Using The Form Prescribed In Section Viii – Bidding Forms. 13. Documents Comprising The Bid: Financial Component 13.1 Unless Otherwise Stated In The Bds, The Financial Component Of The Bid Shall Contain The Following: (a) Financial Bid Form, Which Includes Bid Prices And The Bill Of Quantities And The Applicable Price Schedules, In Accordance With Itb Clauses 15.1 And 15.4; (b) If The Bidder Claims Preference As A Domestic Bidder Or Domestic Entity, A Certification From The Dti, Sec, Or Cda Issued In Accordance With Itb Clause 27; And (c) Any Other Document Required In The Bds 13.2 Unless Otherwise Stated In The Bds, All Bids That Exceed The Abc Shall Not Be Accepted. 14. Alternative Bids Alternative Bids Shall Be Rejected. For This Purpose, Alternative Bid Is An Offer Made By A Bidder In Addition Or As A Substitute To Its Original Bid Which May Be Included As Part Of Its Original Bid Or Submitted Separately Therewith For Purposes Of Bidding. A Bid With Options Is Considered An Alternative Bid Regardless Of Whether Said Bid Proposal Is Contained In A Single Envelope Or Submitted In Two (2) Or More Separate Bid Envelopes. 15. Bid Prices 15.1 The Bidder Shall Complete The Appropriate Price Schedules Included Herein, Stating The Unit Prices, Total Price Per Item, The Total Amount And The Expected Countries Of Origin Of The Goods To Be Supplied Under This Project. 15.2 The Bidder Shall Fill In Rates And Prices For All Items Of The Goods Described In The Bill Of Quantities. Bids Not Addressing Or Providing All Of The Required Items In The Bidding Documents Including, Where Applicable, Bill Of Quantities, Shall Be Considered Non-responsive And, Thus, Automatically Disqualified. In This Regard, Where A Required Item Is Provided, But No Price Is Indicated, The Same Shall Be Considered As Non-responsive, But Specifying A "0" (zero) Or A Dash (-) For The Said Item Would Mean That It Is Being Offered For Free To The Government. 15.3 The Terms Ex Works (exw), Cost, Insurance And Freight (cif), Cost And Insurance Paid To (cip), Delivered Duty Paid (ddp), And Other Trade Terms Used To Describe The Obligations Of The Parties, Shall Be Governed By The Rules Prescribed In The Current Edition Of The International Commercial Terms (incoterms) Published By The International Chamber Of Commerce, Paris. 15.4 Prices Indicated On The Price Schedule Shall Be Entered Separately In The Following Manner: (a) For Goods Offered From Within The Procuring Entity’s Country (i) The Price Of The Goods Quoted Exw (ex Works, Ex Factory, Ex Warehouse, Ex Showroom, Or Off-the-shelf, As Applicable), Including All Customs Duties And Sales And Other Taxes Already Paid Or Payable (i.1) On The Components And Raw Material Used In The Manufacture Or Assembly Of Goods Quoted Ex Works Or Ex Factory; Or (i.2) On The Previously Imported Goods Of Foreign Origin Quoted Ex Warehouse, Ex Showroom, Or Off-the-shelf And Any Procuring Entity Country Sales And Other Taxes Which Will Be Payable On The Goods If The Contract Is Awarded. (ii) The Price For Inland Transportation, Insurance, And Other Local Costs Incidental To Delivery Of The Goods To Their Final Destination. (iii) The Price Of Other (incidental) Services, If Any, Listed In The Bds. (b) For Goods Offered From Abroad: (i) Unless Otherwise Stated In The Bds, The Price Of The Goods Shall Be Quoted Ddp With The Place Of Destination In The Philippines As Specified In The Bds. In Quoting The Price, The Bidder Shall Be Free To Use Transportation Through Carriers Registered In Any Eligible Country. Similarly, The Bidder May Obtain Insurance Services From Any Eligible Source Country. (ii) The Price Of Other (incidental) Services, If Any, Listed In The Bds 15.5 Prices Quoted By The Bidder Shall Be Fixed During The Bidder’s Performance Of The Contract And Not Subject To Variation Or Price Escalation On Any Account, Unless Otherwise Specified In The Bds. A Bid Submitted With An Adjustable Price Quotation Shall Be Treated As Non-responsive And Shall Be Rejected, Pursuant To Itb Clause 24. 15.6 All Bid Prices Shall Be Considered As Fixed Prices, And Therefore Not Subject To Price Escalation During Contract Implementation, Except Under Extraordinary Circumstances As Indicated In The Bds And Specified In The Gcc And Its Corresponding Scc Provision. 16. Bid Currencies 16.1 Prices Shall Be Quoted In The Following Currencies: (a) For Goods That The Bidder Will Supply From Within The Philippines, The Prices Shall Be Quoted In Philippine Pesos. (b) For Goods That The Bidder Will Supply From Outside The Philippines, The Prices May Be Quoted In The Currency(ies) Stated In The Bds. However, For Purposes Of Bid Evaluation, Bids Denominated In Foreign Currencies Shall Be Converted To Philippine Currency Based On The Exchange Rate As Published In The Bsp Reference Rate Bulletin On The Day Of The Bid Opening. 16.2 If So Allowed In Accordance With Itb Clause 16.1, The Procuring Entity For Purposes Of Bid Evaluation And Comparing The Bid Prices Will Convert The Amounts In Various Currencies In Which The Bid Price Is Expressed To Philippine Pesos At The Foregoing Exchange Rates. 16.3 Unless Otherwise Specified In The Bds, Payment Of The Contract Price Shall Be Made In Philippine Pesos. 17. Bid Validity 17.1 Bids Shall Remain Valid For The Period Specified In The Bds Which Shall Not Exceed One Hundred Twenty (120) Calendar Days From The Date Of The Opening Of Bids. 17.2 In Exceptional Circumstances, Prior To The Expiration Of The Bid Validity Period, The Procuring Entity May Request Bidders To Extend The Period Of Validity Of Their Bids. The Request And The Responses Shall Be Made In Writing. The Bid Security Described In Itb Clause 18 Should Also Be Extended Corresponding To The Extension Of The Bid Validity Period At The Least. A Bidder May Refuse The Request Without Forfeiting Its Bid Security, But His Bid Shall No Longer Be Considered For Further Evaluation And Award. A Bidder Granting The Request Shall Not Be Required Or Permitted To Modify Its Bid. 18. Bid Security 18.1 The Procuring Entity Shall Prescribe In The Bds The Acceptable Forms Of Bid Security That Bidders May Opt To Use, Which Shall Include The Bid Securing Declaration (bsd) Or Any Other Form Of Bid Security And The Amount Of Which Shall Be Equal To A Percentage Of The Abc In Accordance With The Following Schedule: Form Of Bid Security Amount Of Bid Security (not Less Than The Percentage Of The Abc) (a) Cash Or Cashier’s/manager’s Check Issued By A Universal Or Commercial Bank Two Percent (2%) (b) Bank Draft/guarantee Or Irrevocable Letter Of Credit Issued By A Universal Or Commercial Bank: Provided, However, That It Shall Be Confirmed Or Authenticated By A Universal Or Commercial Bank, If Issued By A Foreign Bank (c) Surety Bond Callable Upon Demand Issued By A Surety Or Insurance Company Duly Certified By The Insurance Commission As Authorized To Issue Such Security Five Percent (5%) For Biddings Conducted By Lgus, The Procuring Entity May Also Require Bidders To Submit Bid Securities In The Form Of Cashier’s/manager’s Check, Bank Draft/guarantee, Or Irrevocable Letter Of Credit From Other Banks Certified By The Bsp As Authorized To Issue Such Financial Statement. The Bid Securing Declaration Mentioned Above Is An Undertaking Which States, Among Others, That The Bidder Shall Enter Into Contract With The Procuring Entity And Furnish The Performance Security Required Under Itb Clause 33.2, From Receipt Of The Notice Of Award, And Committing To Pay The Corresponding Fine, And Be Suspended For A Period Of Time From Being Qualified To Participate In Any Government Procurement Activity In The Event It Violates Any Of The Conditions Stated Therein As Provided In The Guidelines Issued By The Gppb. 18.2 The Bid Security Should Be Valid For The Period Specified In The Bds. Any Bid Not Accompanied By An Acceptable Bid Security Shall Be Rejected By The Procuring Entity As Non-responsive. 18.3 No Bid Securities Shall Be Returned To Bidders After The Opening Of Bids And Before Contract Signing, Except To Those That Failed Or Declared As Post-disqualified, Upon Submission Of A Written Waiver Of Their Right To File A Motion For Reconsideration And/or Protest. Without Prejudice On Its Forfeiture, Bid Securities Shall Be Returned Only After The Bidder With The Lowest Calculated And Responsive Bid Has Signed The Contract And Furnished The Performance Security, But In No Case Later Than The Expiration Of The Bid Security Validity Period Indicated In Itb Clause 18.2. 18.4 Upon Signing And Execution Of The Contract Pursuant To Itb Clause 32, And The Posting Of The Performance Security Pursuant To Itb Clause 33, The Successful Bidder’s Bid Security Will Be Discharged, But In No Case Later Than The Bid Security Validity Period As Indicated In The Itb Clause 18.2. 18.5 The Bid Security May Be Forfeited: (a) If A Bidder: (i) Withdraws Its Bid During The Period Of Bid Validity Specified In Itb Clause 17; (ii) Does Not Accept The Correction Of Errors Pursuant To Itb Clause 28.3(b); (iii) Fails To Submit The Requirements Within The Prescribed Period, Or A Finding Against Their Veracity, As Stated In Itb Clause 29.2; Or (iv) Any Other Reason Stated In The Bds. (b) If The Successful Bidder: (i) Fails To Sign The Contract In Accordance With Itb Clause 32; (ii) Fails To Furnish Performance Security In Accordance With Itb Clause 33; Or (iii) Any Other Reason Stated In The Bds. 19. Format And Signing Of Bids 19.1 Bidders Shall Submit Their Bids Through Their Duly Authorized Representative Using The Appropriate Forms Provided In Section Viii – Bidding Forms On Or Before The Deadline Specified In The Itb Clauses 21 In Two (2) Separate Sealed Bid Envelopes, And Which Shall Be Submitted Simultaneously. The First Shall Contain The Technical Component Of The Bid, Including The Eligibility Requirements Under Itb Clause 12.1, And The Second Shall Contain The Financial Component Of The Bid. 19.2 Forms As Mentioned In Itb Clause 19.1 Must Be Completed Without Any Alterations To Their Format, And No Substitute Form Shall Be Accepted. All Blank Spaces Shall Be Filled In With The Information Requested 19.3 The Bidder Shall Prepare And Submit An Original Of The First And Second Envelopes As Described In Itb Clauses 12 And 13. In Addition, The Bidder Shall Submit Copies Of The First And Second Envelopes. In The Event Of Any Discrepancy Between The Original And The Machine Copies, The Original Shall Prevail. 19.4 Each And Every Page Of The Bid Form, Including The Schedule Of Prices, Under Section Viii Hereof, Shall Be Signed By The Duly Authorized Representative/s Of The Bidder. Failure To Do So Shall Be A Ground For The Rejection Of The Bid. 19.5 Any Interlineations, Erasures, Or Overwriting Shall Be Valid Only If They Are Signed Or Initialed By The Duly Authorized Representative/s Of The Bidder. 20. Sealing And Marking Of Bids 20.1 Unless Otherwise Indicated In The Bds, Bidders Shall Enclose Their Original Eligibility And Technical Documents Described In Itb Clause 12in One Sealed Envelope Marked “original - Technical Component”, And The Original Of Their Financial Component In Another Sealed Envelope Marked “original - Financial Component”, Sealing Them All In An Outer Envelope Marked “original Bid”. 20.2 Each Copy Of The First And Second Envelopes Shall Be Similarly Sealed Duly Marking The Inner Envelopes As “copy No. ___ - Technical Component” And “copy No. ___ – Financial Component” And The Outer Envelope As “copy No. ___”, Respectively. These Envelopes Containing The Original And The Copies Shall Then Be Enclosed In One Single Envelope. 20.3 The Original And The Number Of Copies Of The Bid As Indicated In The Bds Shall Be Typed Or Computerized In Indelible Ink And Shall Be Signed By The Bidder Or Its Duly Authorized Representative/s. 20.4 All Envelopes Shall (a) Contain The Name Of The Contract To Be Bid In Capital Letters; (b) Bear The Name And Address Of The Bidder In Capital Letters; (c) Be Addressed To The Procuring Entity’s Bac Identified In Itb Clause 1.1, (d) Bear The Specific Identification Of This Bidding Process Indicated In The Itb Clause 1.2; And (e) Bear A Warning “do Not Open Before…” The Date And Time For The Opening Of Bids, In Accordance With Itb Clause 21. 20.5 Bid Envelopes That Are Not Properly Sealed And Marked As Required In The Bidding Documents, Shall Not Be Rejected, But The Bidder Or Its Duly Authorized Representative Shall Acknowledge Such Condition Of The Bid As Submitted. The Bac Or The Procuring Entity Shall Assume No Responsibility For The Misplacement Of The Contents Of The Improperly Sealed Or Marked Bid, Or For Its Premature Opening. D. Submission And Opening Of Bids 21. Deadline For Submission Of Bids Bids Must Be Received By The Procuring Entity’s Bac At The Address And On Or Before The Date And Time Indicated In The Bds. 22. Late Bids Any Bid Submitted After The Deadline For Submission And Receipt Of Bids Prescribed By The Procuring Entity, Pursuant To Itb Clause 21, Shall Be Declared “late” And Shall Not Be Accepted By The Procuring Entity 23. Modification And Withdrawal Of Bids 23.1 The Bidder May Modify Its Bid After It Has Been Submitted; Provided That The Modification Is Received By The Procuring Entity Prior To The Deadline Prescribed For Submission And Receipt Of Bids. The Bidder Shall Not Be Allowed To Retrieve Its Original Bid, But Shall Be Allowed To Submit Another Bid Equally Sealed, Properly Identified, Linked To Its Original Bid Marked As “technical Modification” Or “financial Modification” And Stamped “received” By The Bac. Bid Modifications Received After The Applicable Deadline Shall Not Be Considered And Shall Be Returned To The Bidder Unopened. 23.2 A Bidder May, Through A Letter Of Withdrawal, Withdraw Its Bid After It Has Been Submitted, For Valid And Justifiable Reason; Provided That The Letter Of Withdrawal Is Received By The Procuring Entity Prior To The Deadline Prescribed For Submission And Receipt Of Bids. The Letter Of Withdrawal Must Be Executed By The Duly Authorized Representative Of The Bidder Identified In The Omnibus Sworn Statement, A Copy Of Which Should Be Attached To The Letter. 23.3 Bids Requested To Be Withdrawn In Accordance With Itb Clause 23.1 Shall Be Returned Unopened To The Bidders. A Bidder May Also Express Its Intention Not To Participate In The Bidding Through A Letter Which Should Reach And Be Stamped By The Bac Before The Deadline For Submission And Receipt Of Bids. A Bidder That Withdraws Its Bid Shall Not Be Permitted To Submit Another Bid, Directly Or Indirectly, For The Same Contract. 23.4 No Bid May Be Modified After The Deadline For Submission Of Bids. No Bid May Be Withdrawn In The Interval Between The Deadline For Submission Of Bids And The Expiration Of The Period Of Bid Validity Specified By The Bidder On The Financial Bid Form. Withdrawal Of A Bid During This Interval Shall Result In The Forfeiture Of The Bidder’s Bid Security, Pursuant To Itb Clause 18.5, And The Imposition Of Administrative, Civil And Criminal Sanctions As Prescribed By Ra 9184 And Its Irr 24. Opening And Preliminary Examination Of Bids 24.1 24.2 The Bac Shall Open The Bids In Public, Immediately After The Deadline For The Submission And Receipt Of Bids, As Specified In The Bds. In Case The Bids Cannot Be Opened As Scheduled Due To Justifiable Reasons, The Bac Shall Take Custody Of The Bids Submitted And Reschedule The Opening Of Bids On The Next Working Day Or At The Soonest Possible Time Through The Issuance Of A Notice Of Postponement To Be Posted In The Philgeps Website Of The Procuring Entity Concerned, If Available. The Bac Shall Open The First Bid Envelopes Of Bidders In Public As Specified In The Bds To Determine Each Bidder’s Compliance With The Documents Prescribed In Itb Clause 12. For This Purpose, The Bac Shall Check The Submitted Documents Of Each Bidder Against A Checklist Of Required Documents To Ascertain If They Are All Present, Using A Non-discretionary “pass/fail” Criterion. If A Bidder Submits The Required Document, It Shall Be Rated “passed” For That Particular Requirement. In This Regard, Bids That Fail To Include Any Requirement Or Are Incomplete Or Patently Insufficient Shall Be Considered As “failed”. Otherwise, The Bac Shall Rate The Said First Bid Envelope As “passed”. 24.3 Immediately After Determining Compliance With The Requirements In The First Envelope, The Bac Shall Forthwith Open The Second Bid Envelope Of Each Remaining Eligible Bidder Whose First Bid Envelope Was Rated “passed”. The Second Envelope Of Each Complying Bidder Shall Be Opened Within The Same Day. In Case One Or More Of The Requirements In The Second Envelope Of A Particular Bid Is Missing, Incomplete Or Patently Insufficient, And/or If The Submitted Total Bid Price Exceeds The Abc Unless Otherwise Provided In Itb Clause 13.2, The Bac Shall Rate The Bid Concerned As “failed”. Only Bids That Are Determined To Contain All The Bid Requirements For Both Components Shall Be Rated “passed” And Shall Immediately Be Considered For Evaluation And Comparison 24.4 Letters Of Withdrawal Shall Be Read Out And Recorded During Bid Opening, And The Envelope Containing The Corresponding Withdrawn Bid Shall Be Returned To The Bidder Unopened. If The Withdrawing Bidder’s Representative Is In Attendance, The Original Bid And All Copies Thereof Shall Be Returned To The Representative During The Bid Opening. If The Representative Is Not In Attendance, The Bid Shall Be Returned Unopened By Registered Mail. The Bidder May Withdraw Its Bid Prior To The Deadline For The Submission And Receipt Of Bids, Provided That The Corresponding Letter Of Withdrawal Contains A Valid Authorization Requesting For Such Withdrawal, Subject To Appropriate Administrative Sanctions 24.5 If A Bidder Has Previously Secured A Certification From The Procuring Entity To The Effect That It Has Previously Submitted The Above-enumerated Class “a” Documents, The Said Certification May Be Submitted In Lieu Of The Requirements Enumerated In Itb Clause 12.1(a), Items (i) To (v). 24.6 In The Case Of An Eligible Foreign Bidder As Described In Itb Clause 5, The Class “a” Documents Described In Itb Clause 12.1(a) May Be Substituted With The Appropriate Equivalent Documents, If Any, Issued By The Country Of The Foreign Bidder Concerned. 24.7 Each Partner Of A Joint Venture Agreement Shall Likewise Submit The Requirements In Itb Clauses 12.1(a)(i) And 12.1(a)(ii). Submission Of Documents Required Under Itb Clauses 12.1(a)(iii) To 12.1(a)(v) By Any Of The Joint Venture Partners Constitutes Compliance. 24.8 The Procuring Entity Shall Prepare The Minutes Of The Proceedings Of The Bid Opening That Shall Include, As A Minimum: (a) Names Of Bidders, Their Bid Price, Bid Security, Findings Of Preliminary Examination; And (b) Attendance Sheet. The Bac Members Shall Sign The Abstract Of Bids As Read. E. Evaluation And Comparison Of Bids 25. Process To Be Confidential 25.1 Members Of The Bac, Including Its Staff And Personnel, As Well As Its Secretariat And Twg, Are Prohibited From Making Or Accepting Any Kind Of Communication With Any Bidder Regarding The Evaluation Of Their Bids Until The Issuance Of The Notice Of Award, Unless Otherwise Allowed In The Bds Or In The Case Of Itb Clause 26. 25.2 Any Effort By A Bidder To Influence The Procuring Entity In The Procuring Entity’s Decision In Respect Of Bid Evaluation, Bid Comparison Or Contract Award Will Result In The Rejection Of The Bidder’s Bid. 26. Clarification Of Bids To Assist In The Evaluation, Comparison, And Post-qualification Of The Bids, The Procuring Entity May Ask In Writing Any Bidder For A Clarification Of Its Bid. All Responses To Requests For Clarification Shall Be In Writing. Any Clarification Submitted By A Bidder In Respect To Its Bid And That Is Not In Response To A Request By The Procuring Entity Shall Not Be Considered. 27. Domestic Preference 27.1 Unless Otherwise Stated In The Bds, The Procuring Entity Will Grant A Margin Of Preference For The Purpose Of Comparison Of Bids In Accordance With The Following: (a) The Preference Shall Be Applied When (i) The Lowest Foreign Bid Is Lower Than The Lowest Bid Offered By A Domestic Bidder, Or (ii) The Lowest Bid Offered By A Non-philippine National Is Lower Than The Lowest Bid Offered By A Domestic Entity. (b) For Evaluation Purposes, The Lowest Foreign Bid Or The Bid Offered By A Non-philippine National Shall Be Increased By Fifteen Percent (15%). (c) In The Event That (i) The Lowest Bid Offered By A Domestic Entity Does Not Exceed The Lowest Foreign Bid As Increased, Or (ii) The Lowest Bid Offered By A Non-philippine National As Increased, Then The Procuring Entity Shall Award The Contract To The Domestic Bidder/entity At The Amount Of The Lowest Foreign Bid Or The Bid Offered By A Non-philippine National, As The Case May Be. (d) If The Domestic Entity/bidder Refuses To Accept The Award Of Contract At The Amount Of The Foreign Bid Or Bid Offered By A Non-philippine National Within Two (2) Calendar Days From Receipt Of Written Advice From The Bac, The Procuring Entity Shall Award To The Bidder Offering The Foreign Bid Or The Non-philippine National, As The Case May Be, Subject To Post-qualification And Submission Of All The Documentary Requirements Under These Bidding Documents. 27.2 A Bidder May Be Granted Preference As A Domestic Entity Subject To The Certification From The Dti (in Case Of Sole Proprietorships), Sec (in Case Of Partnerships And Corporations), Or Cda (in Case Of Cooperatives) That The (a) Sole Proprietor Is A Citizen Of The Philippines Or The Partnership, Corporation, Cooperative, Or Association Is Duly Organized Under The Laws Of The Philippines With At Least Seventy Five Percent (75%) Of Its Interest Or Outstanding Capital Stock Belonging To Citizens Of The Philippines, (b) Habitually Established In Business And Habitually Engaged In The Manufacture Or Sale Of The Merchandise Covered By His Bid, And (c) The Business Has Been In Existence For At Least Five (5) Consecutive Years Prior To The Advertisement And/or Posting Of The Invitation To Bid For This Project. 27.3 A Bidder May Be Granted Preference As A Domestic Bidder Subject To The Certification From The Dti That The Bidder Is Offering Unmanufactured Articles, Materials Or Supplies Of The Growth Or Production Of The Philippines, Or Manufactured Articles, Materials, Or Supplies Manufactured Or To Be Manufactured In The Philippines Substantially From Articles, Materials, Or Supplies Of The Growth, Production, Or Manufacture, As The Case May Be, Of The Philippines. 28. Detailed Evaluation And Comparison Of Bids 28.1 The Procuring Entity Will Undertake The Detailed Evaluation And Comparison Of Bids Which Have Passed The Opening And Preliminary Examination Of Bids, Pursuant To Itb Clause 24, In Order To Determine The Lowest Calculated Bid. 28.2 The Lowest Calculated Bid Shall Be Determined In Two Steps. (a) The Detailed Evaluation Of The Financial Component Of The Bids, To Establish The Correct Calculated Prices Of The Bids; And (b) The Ranking Of The Total Bid Prices As So Calculated From The Lowest To The Highest. The Bid With The Lowest Price Shall Be Identified As The Lowest Calculated Bid. 28.3 The Procuring Entity's Bac Shall Immediately Conduct A Detailed Evaluation Of All Bids Rated “passed,” Using Non-discretionary Pass/fail Criteria. Unless Otherwise Specified In The Bds, The Bac Shall Consider The Following In The Evaluation Of Bids. (a) Completeness Of The Bid. Unless The Itb Specifically Allows Partial Bids, Bids Not Addressing Or Providing All Of The Required Items In The Schedule Of Requirements Including, Where Applicable, Bill Of Quantities, Shall Be Considered Non-responsive And, Thus, Automatically Disqualified. In This Regard, Where A Required Item Is Provided, But No Price Is Indicated, The Same Shall Be Considered As Non-responsive, But Specifying A "0" (zero) Or A Dash (-) For The Said Item Would Mean That It Is Being Offered For Free To The Procuring Entity; And (b) Arithmetical Corrections. Consider Computational Errors And Omissions To Enable Proper Comparison Of All Eligible Bids. It May Also Consider Bid Modifications, If Allowed In The Bds. Any Adjustment Shall Be Calculated In Monetary Terms To Determine The Calculated Prices. 28.4 Based On The Detailed Evaluation Of Bids, Those That Comply With The Above-mentioned Requirements Shall Be Ranked In The Ascending Order Of Their Total Calculated Bid Prices, As Evaluated And Corrected For Computational Errors, Discounts And Other Modifications, To Identify The Lowest Calculated Bid. Total Calculated Bid Prices, As Evaluated And Corrected For Computational Errors, Discounts And Other Modifications, Which Exceed The Abc Shall Not Be Considered. 28.5 Unless Otherwise Indicated In The Bds, The Procuring Entity’s Evaluation Of Bids Shall Only Be Based On The Bid Price Quoted In The Financial Bid Form. 28.6 Bids Shall Be Evaluated On An Equal Footing To Ensure Fair Competition. For This Purpose, All Bidders Shall Be Required To Include In Their Bids The Cost Of All Taxes, Such As, But Not Limited To, Value Added Tax (vat), Income Tax, Local Taxes, And Other Fiscal Levies And Duties Which Shall Be Itemized In The Bid Form And Reflected In The Detailed Estimates. Such Bids, Including Said Taxes, Shall Be The Basis For Bid Evaluation And Comparison. 29. Post-qualification 29.1 The Procuring Entity Shall Determine To Its Satisfaction Whether The Bidder That Is Evaluated As Having Submitted The Lowest Calculated Bid (lcb) Complies With And Is Responsive To All The Requirements And Conditions Specified In Itb Clauses 5, 12, And 13. 29.2 Within A Non-extendible Period Of Five (5) Calendar Days From Receipt By The Bidder Of The Notice From The Bac That It Submitted The Lcb, The Bidder Shall Submit The Following Documentary Requirements: (a) Latest Income And Business Tax Returns In The Form Specified In The Bds; (b) Other Appropriate Licenses And Permits Required By Law And Stated In The Bds. Failure Of The Bidder Declared As Lowest Calculated Bid To Duly Submit The Above Requirements On Time Under This Clause Or A Finding Against The Veracity Of Such Shall Be Ground For Forfeiture Of The Bid Security And Disqualification Of The Bidder For Award. 29.3 The Determination Shall Be Based Upon An Examination Of The Documentary Evidence Of The Bidder’s Qualifications Submitted Pursuant To Itb Clauses 12 And 13, As Well As Other Information As The Procuring Entity Deems Necessary And Appropriate, Using A Non-discretionary “pass/fail” Criterion. 29.4 If The Bac Determines That The Bidder With The Lowest Calculated Bid Passes All The Criteria For Post-qualification, It Shall Declare The Said Bid As The Lowest Calculated Responsive Bid, And Recommend To The Head Of The Procuring Entity The Award Of Contract To The Said Bidder At Its Submitted Bid Price Or Its Calculated Bid Price, Whichever Is Lower. 29.5 A Negative Determination Shall Result In Rejection Of The Bidder’s Bid, In Which Event The Procuring Entity Shall Proceed To The Next Lowest Calculated Bid To Make A Similar Determination Of That Bidder’s Capabilities To Perform Satisfactorily. If The Second Bidder, However, Fails The Post Qualification, The Procedure For Post Qualification Shall Be Repeated For The Bidder With The Next Lowest Calculated Bid, And So On Until The Lowest Calculated Responsive Bid Is Determined For Contract Award. 29.6 Within A Period Not Exceeding Fifteen (15) Calendar Days From The Date Of Receipt Of The Recommendation Of The Bac, The Head Of The Procuring Entity Shall Approve Or Disapprove The Said Recommendation. 30. Reservation Clause 30.1 Notwithstanding The Eligibility Or Post-qualification Of A Bidder, The Procuring Entity Concerned Reserves The Right To Review Its Qualifications At Any Stage Of The Procurement Process If It Has Reasonable Grounds To Believe That A Misrepresentation Has Been Made By The Said Bidder, Or That There Has Been A Change In The Bidder’s Capability To Undertake The Project From The Time It Submitted Its Eligibility Requirements. Should Such Review Uncover Any Misrepresentation Made In The Eligibility And Bidding Requirements, Statements Or Documents, Or Any Changes In The Situation Of The Bidder Which Will Affect Its Capability To Undertake The Project So That It Fails The Preset Eligibility Or Bid Evaluation Criteria, The Procuring Entity Shall Consider The Said Bidder As Ineligible And Shall Disqualify It From Submitting A Bid Or From Obtaining An Award Or Contract. 30.2 Based On The Following Grounds, The Procuring Entity Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding At Any Time Prior To The Contract Award, Or Not To Award The Contract, Without Thereby Incurring Any Liability, And Make No Assurance That A Contract Shall Be Entered Into As A Result Of The Bidding: (a) If There Is Prima Facie Evidence Of Collusion Between Appropriate Public Officers Or Employees Of The Procuring Entity, Or Between The Bac And Any Of The Bidders, Or If The Collusion Is Between Or Among The Bidders Themselves, Or Between A Bidder And A Third Party, Including Any Act Which Restricts, Suppresses Or Nullifies Or Tends To Restrict, Suppress Or Nullify Competition; (b) If The Procuring Entity’s Bac Is Found To Have Failed In Following The Prescribed Bidding Procedures; Or (c) For Any Justifiable And Reasonable Ground Where The Award Of The Contract Will Not Redound To The Benefit Of The Gop As Follows: (i) If The Physical And Economic Conditions Have Significantly Changed So As To Render The Project No Longer Economically, Financially Or Technically Feasible As Determined By The Head Of The Procuring Entity; (ii) If The Project Is No Longer Necessary As Determined By The Head Of The Procuring Entity; And (iii) If The Source Of Funds For The Project Has Been Withheld Or Reduced Through No Fault Of The Procuring Entity. 30.3 In Addition, The Procuring Entity May Likewise Declare A Failure Of Bidding When: (a) No Bids Are Received; (b) All Prospective Bidders Are Declared Ineligible; (c) All Bids Fail To Comply With All The Bid Requirements Or Fail Post-qualification; Or (d) The Bidder With The Lowest Calculated Responsive Bid Refuses, Without Justifiable Cause To Accept The Award Of Contract, And No Award Is Made In Accordance With Section 40 Of The Irr Of Ra 9184. F. Award Of Contract 31. Contract Award 31.1 Subject To Itb Clause 29, The Procuring Entity Shall Award The Contract To The Bidder Whose Bid Has Been Determined To Be The Lcrb. 31.2 Prior To The Expiration Of The Period Of Bid Validity, The Procuring Entity Shall Notify The Successful Bidder In Writing That Its Bid Has Been Accepted, Through A Notice Of Award Received Personally Or Sent By Registered Mail Or Electronically, Receipt Of Which Must Be Confirmed In Writing Within Two (2) Days By The Bidder With The Lcrb And Submitted Personally Or Sent By Registered Mail Or Electronically To The Procuring Entity. 31.3 Notwithstanding The Issuance Of The Notice Of Award, Award Of Contract Shall Be Subject To The Following Conditions: (a) Submission Of The Valid Jva, If Applicable, Within Ten (10) Calendar Days From Receipt By The Bidder Of The Notice From The Bac That The Bidder Has The Lcrb; (b) Posting Of The Performance Security In Accordance With Itb Clause 33; (c) Signing Of The Contract As Provided In Itb Clause 32; And (d) Approval By Higher Authority, If Required. 31.4 At The Time Of Contract Award, The Procuring Entity Shall Not Increase Or Decrease The Quantity Of Goods Originally Specified In Section Vi – Schedule Of Requirements. 32. Signing Of The Contract 32.1 At The Same Time As The Procuring Entity Notifies The Successful Bidder That Its Bid Has Been Accepted, The Procuring Entity Shall Send The Contract Form To The Bidder, Which Contract Has Been Provided In The Bidding Documents, Incorporating Therein All Agreements Between The Parties. 32.2 Within Ten (10) Calendar Days From Receipt Of The Notice Of Award, The Successful Bidder Shall Post The Required Performance Security And Sign And Date The Contract And Return It To The Procuring Entity. 32.3 The Procuring Entity Shall Enter Into Contract With The Successful Bidder Within The Same Ten (10) Calendar Day Period Provided That All The Documentary Requirements Are Complied With. 32.4 The Following Documents Shall Form Part Of The Contract. (a) Contract Agreement; (b) Bidding Documents; (c) Winning Bidder’s Bid, Including The Technical And Financial Proposals, And All Other Documents/statements Submitted; (d) Performance Security; (e) Notice Of Award Of Contract; And (f) Other Contract Documents That May Be Required By Existing Laws And/or Specified In The Bds. 33. Performance Security 33.1 To Guarantee The Faithful Performance By The Winning Bidder Of Its Obligations Under The Contract, It Shall Post A Performance Security Within A Maximum Period Of Ten (10) Calendar Days From The Receipt Of The Notice Of Award From The Procuring Entity And In No Case Later Than The Signing Of The Contract. 33.2 The Procuring Entity Shall Prescribe At Least One (1) Acceptable Form Of Performance Security Taken From The Categories Below That Bidders May Opt To Use, Denominated In Philippine Pesos And Posted In Favor Of The Procuring Entity: Form Of Performance Security Amount Of Performance Security (not Less Than The Percentage Of The Total Contract Price) (a) Cash Or Cashier’s/manager’s Check Issued By A Universal Or Commercial Bank Five Percent (5%) (b) Bank Draft/guarantee Or Irrevocable Letter Of Credit Issued By A Universal Or Commercial Bank: Provided, However, That It Shall Be Confirmed Or Authenticated By A Universal Or Commercial Bank, If Issued By A Foreign Bank. (c) Surety Bond Callable Upon Demand Issued By A Surety Or Insurance Company Duly Certified By The Insurance Commission As Authorized To Issue Such Security. Thirty Percent (30%) (d) Performance Securing Declaration (psd) None 33.3 Performance Security As Indicated In Section 17.1 (k) And 39 Of The 2016 Revised Irr Of Ra No. 9184, While Includes The Performance Securing Declaration (psd) As An Alternative Performance Security During A State Of Calamity Or Imposition Of Community Quarantine Pursuant To Gppb Resolution No. 09-2020. Failure Of The Successful Bidder To Comply With The Above-mentioned Requirement Shall Constitute Sufficient Ground For The Annulment Of The Award And Forfeiture Of The Bid Security, In Which Event The Procuring Entity Shall Initiate And Complete The Post Qualification Of The Second Lowest Calculated Bid. The Procedure Shall Be Repeated Until The Lcrb Is Identified And Selected For Contract Award. However If No Bidder Passed Post-qualification, The Bac Shall Declare The Bidding A Failure And Conduct A Re-bidding With Re-advertisement. 34. Notice To Proceed 34.1 Within Seven (7) Calendar Days From The Date Of Approval Of The Contract By The Appropriate Government Approving Authority, The Procuring Entity Shall Issue Its Notice To Proceed Together With A Copy Or Copies Of The Approved Contract To The Successful Bidder. All Notices Called For By The Terms Of The Contract Shall Be Effective Only At The Time Of Receipt Thereof By The Successful Bidder. 34.2 The Contract Effectivity Date Shall Be Provided In The Notice To Proceed By The Procuring Entity, Which Date Shall Not Be Later Than Seven (7) Calendar Days From The Issuance Of The Notice To Proceed. 35. Protest Mechanism Decision Of The Procuring Entity At Any Stage Of The Procurement Process May Be Questioned In Accordance With Section 55 Of The Revised Implementing Rules And Regulations Of Republic Act 9184. Section Iii – Bid Data Sheet Itb Clause 1.1 The Procuring Entity Is The Local Government Of Badiangan, Iloilo 1.2 The Reference Is: Supply And Delivery Of Lighting Materials For The Socio-cultural Activities (kasanag Sa Paskwa), Municipal Hall, Badiangan, Iloilo. Project Identification No. 2024 – 060 – B. 2.0 The Funding Source Is Through The General Fund Of The Local Government Of Badiangan, Iloilo In The Amount Of P 291,585.00. 5.1 No Further Instructions. 5.2 None Of The Circumstances Mentioned In The Itb Clause Exists In This Project. Foreign Bidders, Except Those Falling Under Itb Clause 5.2(b), May Not Participate In This Project. 5.4 The Bidder Must Have Completed, Within The Period Specified In The Invitation To Bid And Itb Clause 12.1(a)(ii), A Single Contract That Is Similar To This Project, Equivalent To At Least Fifty Percent (50%) Of The Abc. For This Purpose, Similar Contracts Shall Refer To The Supply And Delivery Of Goods That Is/are Similar In Type And Brand To The Goods Being Bidded-out. 5.5 No Further Instructions. 6.3 No Further Instructions. 7 No Further Instructions. 8.1 Subcontracting Is Not Allowed. 8.2 Not Applicable. 9.1 Not Applicable. 10.1 The Procuring Entity’s Address Is: Badiangan Municipal Hall R.c. Tabiana St., Poblacion, Badiangan, Iloilo 5033 Contact Person: Mr. Humbert S. Recomono Head: Bac Secretariat Municipal Hall, Badiangan, Iloilo Tel. No. (033) 320-7809 C.p. No. 09198501252 12.1 The First Envelope Shall Contain The Eligibility And Technical Documents Stated In The Itb Clause. However, If The Bidder Maintains A Current And Updated File Of Its Class “a” Documents With The Bac Of The Local Government Of Badiangan, Iloilo, A Certification To That Effect Issued By Its Bac May Be Submitted In Lieu Of The Class “a” Documents. 12.1(a)(i) No Other Acceptable Proof Of Registration Is Recognized 12.1(a)(ii) The Statement Of All Ongoing And Single Largest Completed Government And Private Contracts Shall Include All Such Contracts Within The Last Two (2) Years Prior To The Deadline For The Submission And Receipt Of Bids. 13.1 No Additional Requirements. 13.2 The Approved Budget For The Contract (abc) Is: P 291,585.00 Any Bid With A Financial Component Exceeding This Amount Shall Not Be Accepted. 15.4(a)(iii) No Incidental Services Required. 15.4(b) Not Applicable. 15.5 Bid Prices Shall Be Fixed. Adjustable Price Proposals Shall Be Treated As Non-responsive And Shall Be Rejected. 15.6 Extraordinary Circumstances Refer To Events That May Be Determined By The National Economic And Development Authority In Accordance With The Civil Code Of The Philippines, And Upon The Recommendation Of The Procuring Entity. 16.1(b) The Bid Prices For Goods Supplied From Outside Of The Philippines Shall Be Quoted In Philippine Pesos. 16.3 No Further Instructions. 17.1 Bids Shall Be Valid Until 120 Calendar Days After Bidding. 18.1 The Bid Security Shall Be In The Form Of A Bid Securing Declaration (bsd), Or Any Of The Following Forms: 1. P (2% Of Abc), If Bid Security Is In Cash, Cashier’s/manager’s Check, Bank Draft/guarantee Or Irrevocable Letter Of Credit; Or 2. P (5% Of Abc), If Bid Security Is In Surety Bond 18.2 The Bid Security Shall Be Valid Until 120 Calendar Days After Bidding. 18.5(a)(iv) The Following Are Additional Grounds For Forfeiture Of Bid Security: 1. Submission Of Eligibility Requirements Containing False Information Or Falsified Documents. 2. Submission Of Bids That Contain False Information Or Falsified Documents, Or The Concealment Of Such Information In The Bids In Order To Influence The Outcome Of Eligibility Screening Or Any Other Stage Of The Public Bidding. 3. Allowing The Use Of One’s Name, Or Using The Name Of Another For Purposes Of Public Bidding. 4. Withdrawal Of A Bid, Or Refusal To Accept An Award, Or Enter Into Contract With The Government Without Justifiable Cause, After The Bidder Had Been Adjudged As Having Submitted The Lowest Calculated And Responsive Bid. 5. Refusal Or Failure To Post The Required Performance Security Within The Prescribed Time. 6. Refusal To Clarify Or Validate In Writing Its Bid During Post-qualification Within A Period Of Seven (7) Calendar Days From Receipt Of The Request For Clarification. 7. Any Documented Unsolicited Attempt By A Bidder To Unduly Influence The Outcome Of The Bidding In His Favor. 8. Failure Of The Potential Joint Venture Partners To Enter Into The Joint Venture After The Bid Is Declared As Successful. 9. All Other Acts That Tend To Defeat The Purpose Of The Competitive Bidding, Such As Habitually Withdrawing From Bidding, Submitting Late Bids Or Patently Insufficient Bid, For At Least Three (3) Times Within A Year, Except For Valid Reasons. 18.5(b)(iii) No Further Instructions. 20.1 The Documents Enclosed In The Original Bid Should Be Original Copy Or Duly Stamped Certified True/ Machine Copy With Printed Name And Signature Of The Owner Of The Company Or The Duly Authorized Representative Of The Company As Indicated In The Special Power Of Attorney (spa) Or Secretary’s Certificate. The Duly Authorized Representative Should Have A Specimen Signature In The Spa Or Secretary’s Certificate. 20.3 Each Bidder Shall Submit One (1) Original And Two (2) Copies Of The First And Second Components Of Its Bid. The Photocopied Copies Of The Documents Enclosed In The First And Second Components Of The Bid Should Be Duly Stamped Certified True/ Machine Copy With Printed Name And Signature Of The Owner Of The Company Or The Duly Authorized Representative Of The Company As Indicated In The Special Power Of Attorney (spa) Or Secretary’s Certificate. The Duly Authorized Representative Should Have A Specimen Signature In The Spa Or Secretary’s Certificate. 21 The Address For Submission Of Bids Is: Municipal Budget Office, Municipal Hall, Badiangan, Iloilo The Deadline For Submission Of Bid Is: November 25, 2024; 8:30 A.m. 24.1 The Place Of Bid Opening Is: Municipal Social Hall, Badiangan, Iloilo The Date And Time Of Bid Opening Is: November 25, 2024; 09:00 A.m. 25.1 No Further Instructions. 27.1 No Further Instructions. 28.3 No Further Instructions. 28.3(b) Modification Of Bids Is Not Allowed. 28.5 No Further Instructions. 29.2(a) Only Tax Returns Filed And Taxes Paid Through The Bir Electronic Filing And Payment System (efps) Shall Be Accepted. Note: The Latest Income And Business Tax Returns Are Those Within The Last Six Months Preceding The Date Of Bid Submission. 29.2(d) None Required. 32.4(g) None Required. 34.2 The Effective Date Of The Contract Is Seven (7) Calendar Days Upon Receipt Of Notice To Proceed Issued By The Procuring Entity. Section Iv. General Conditions Of Contract 1. Definitions 1.1 In This Contract, The Following Terms Shall Be Interpreted As Indicated. (a) “the Contract” Means The Agreement Entered Into Between The Procuring Entity And The Supplier, As Recorded In The Contract Form Signed By The Parties, Including All Attachments And Appendices Thereto And All Documents Incorporated By Reference Therein. (b) “the Contract Price” Means The Price Payable To The Supplier Under The Contract For The Full And Proper Performance Of Its Contractual Obligations. (c) “the Goods” Means All Of The Supplies, Equipment, Machinery, Spare Parts, Other Materials And/or General Support Services Which The Supplier Is Required To Provide To The Procuring Entity Under The Contract. (d) “the Services” Means Those Services Ancillary To The Supply Of The Goods, Such As Transportation And Insurance, And Any Other Incidental Services, Such As Installation, Commissioning, Provision Of Technical Assistance, Training, And Other Such Obligations Of The Supplier Covered Under The Contract. (e) “gcc” Means The General Conditions Of Contract Contained In This Section. (f) “scc” Means The Special Conditions Of Contract. (g) “the Procuring Entity” Means The Organization Purchasing The Goods, As Named In The Scc,. (h) “the Procuring Entity’s Country” Is The Philippines. (i) “the Supplier” Means The Individual Contractor, Manufacturer, Distributor, Or Firm Supplying/manufacturing The Goods And Services Under This Contract And Named In The Scc, (j) The “funding Source” Means The Organization Named In The Scc,. (k) “the Project Site,” Where Applicable, Means The Place Or Places Named In The Scc, (l) “day” Means Calendar Day. (m) The “effective Date” Of The Contract Will Be The Date Of Receipt By The Supplier Of The Notice To Proceed Or The Date Provided In The Notice To Proceed. Performance Of All Obligations Shall Be Reckoned From The Effective Date Of The Contract. (n) “verified Report” Refers To The Report Submitted By The Implementing Unit To The Head Of The Procuring Entity Setting Forth Its Findings As To The Existence Of Grounds Or Causes For Termination And Explicitly Stating Its Recommendation For The Issuance Of A Notice To Terminate. 2. Corrupt, Fraudulent, Collusive, And Coercive Practices 2.1 The Procuring Entity As Well As The Bidders, Contractors, Or Suppliers Shall Observe The Highest Standard Of Ethics During The Procurement And Execution Of This Contract. In Pursuance Of This Policy, The Procuring Entity. (a) Defines, For The Purposes Of This Provision, The Terms Set Forth Below As Follows (i) "corrupt Practice" Means Behavior On The Part Of Officials In The Public Or Private Sectors By Which They Improperly And Unlawfully Enrich Themselves, Others, Or Induce Others To Do So, By Misusing The Position In Which They Are Placed, And It Includes The Offering, Giving, Receiving, Or Soliciting Of Anything Of Value To Influence The Action Of Any Such Official In The Procurement Process Or In Contract Execution; Entering, On Behalf Of The Government, Into Any Contract Or Transaction Manifestly And Grossly Disadvantageous To The Same, Whether Or Not The Public Officer Profited Or Will Profit Thereby, And Similar Acts As Provided In Republic Act 3019. (ii) "fraudulent Practice" Means A Misrepresentation Of Facts In Order To Influence A Procurement Process Or The Execution Of A Contract To The Detriment Of The Procuring Entity, And Includes Collusive Practices Among Bidders (prior To Or After Bid Submission) Designed To Establish Bid Prices At Artificial, Non-competitive Levels And To Deprive The Procuring Entity Of The Benefits Of Free And Open Competition. (iii) “collusive Practices” Means A Scheme Or Arrangement Between Two Or More Bidders, With Or Without The Knowledge Of The Procuring Entity, Designed To Establish Bid Prices At Artificial, Non-competitive Levels. (iv) “coercive Practices “ Means Harming Or Threatening To Harm, Directly Or Indirectly, Persons, Or Their Property To Influence Their Participation In A Procurement Process, Or Effect The Execution Of A Contract; (v) “obstructive Practice” Is (aa) Deliberately Destroying, Falsifying, Altering Or Concealing Of Evidence Material To An Administrative Proceedings Or Investigation Or Making False Statements To Investigators In Order To Materially Impede An Administrative Proceedings Or Investigation Of The Procuring Entity Or Any Foreign Government/foreign Or International Financing Institution Into Allegations Of A Corrupt, Fraudulent, Coercive Or Intimidating Any Party To Prevent If From Disclosing Its Knowledge Of Matters Relevant To The Administrative Proceedings Or Investigation Or From Pursuing Such Proceedings Or Investigation; Or (bb) Acts Intended To Materially Impede The Exercise Of The Inspection And Audit Rights Of The Procuring Entity Or Any Foreign Government/foreign Or International Financing Institution Herein. (b) Will Reject A Proposal For Award If It Determines That The Bidder Recommended For Award Has Engaged In Any Of The Practices Mentioned In This Clause For Purposes Of Competing For The Contract. 3. Inspection And Audit By The Funding Source The Supplier Shall Permit The Funding Source To Inspect The Supplier’s Accounts And Records Relating To The Performance Of The Supplier And To Have Them Audited By Auditors Appointed By The Funding Source, If So Required By The Funding Source. 4. Governing Law And Language 4.1 This Contract Shall Be Interpreted In Accordance With The Laws Of The Republic Of The Philippines. 4.2 This Contract Has Been Executed In The English Language, Which Shall Be The Binding And Controlling Language For All Matters Relating To The Meaning Or Interpretation Of This Contract. All Correspondence And Other Documents Pertaining To This Contract Exchanged By The Parties Shall Be Written In English. 5. Notices 5.1 Any Notice, Request, Or Consent Required Or Permitted To Be Given Or Made Pursuant To This Contract Shall Be In Writing. Any Such Notice, Request, Or Consent Shall Be Deemed To Have Been Given Or Made When Received By The Concerned Party, Either In Person Or Through An Authorized Representative Of The Party To Whom The Communication Is Addressed, Or When Sent By Registered Mail, Telex, Telegram, Or Facsimile To Such Party At The Address Specified In The Scc, Which Shall Be Effective When Delivered And Duly Received Or On The Notice’s Effective Date, Whichever Is Later. 5.2 A Party May Change Its Address For Notice Hereunder By Giving The Other Party Notice Of Such Change Pursuant To The Provisions Listed In The Scc For Gcc Clause 5.1. 6. Scope Of Contract 6.1 The Goods And Related Services To Be Provided Shall Be As Specified In Section Vi – Schedule Of Requirements. 6.2 This Contract Shall Include All Such Items, Although Not Specifically Mentioned, That Can Be Reasonably Inferred As Being Required For Its Completion As If Such Items Were Expressly Mentioned Herein. Any Additional Requirements For The Completion Of This Contract Shall Be Provided In The Scc 7. Subcontracting 7.1 Subcontracting Of Any Portion Of The Goods, If Allowed In The Bds, Does Not Relieve The Supplier Of Any Liability Or Obligation Under This Contract. The Supplier Will Be Responsible For The Acts, Defaults, And Negligence Of Any Subcontractor, Its Agents, Servants Or Workmen As Fully As If These Were The Supplier’s Own Acts, Defaults, Or Negligence, Or Those Of Its Agents, Servants Or Workmen. 7.2 Subcontractors Disclosed And Identified During The Bidding May Be Changed During The Implementation Of This Contract, Subject To Compliance With The Required Qualifications And The Approval Of The Procuring Entity. 8. Procuring Entity’s Responsibilities 8.1 Whenever The Performance Of The Obligations In This Contract Requires That The Supplier Obtain Permits, Approvals, Import, And Other Licenses From Local Public Authorities, The Procuring Entity Shall, If So Needed By The Supplier, Make Its Best Effort To Assist The Supplier In Complying With Such Requirements In A Timely And Expeditious Manner. 8.2 The Procuring Entity Shall Pay All Costs Involved In The Performance Of Its Responsibilities In Accordance With Gcc Clause 6. 9. Prices Prices Charged By The Supplier For Goods Delivered And/or Services Performed Under This Contract Shall Not Vary From The Prices Quoted By The Supplier In Its Bid, With The Exception Of Any Change In Price Resulting From A Change Order Issued In Accordance With Gcc Clause 29, Or If Applicable, Adjustments Authorized In Accordance With The Price Adjustment Provisions Specified In The Scc.. 10. Payment 10.1 Unless Otherwise Specified In The Scc, Payments Shall Be Made Only Upon A Certification By The Head Of The Procuring Entity To The Effect That The Goods Have Been Rendered Or Delivered In Accordance With The Terms Of This Contract And Have Been Duly Inspected And Accepted. Except With The Prior Approval Of The President No Payment Shall Be Made For Services Not Yet Rendered Or For Supplies And Materials Not Yet Delivered Under This Contract. Ten Percent (10%) Of The Amount Of Each Payment Shall Be Retained By The Procuring Entity To Cover The Supplier’s Warranty Obligations Under This Contract As Described In Gcc Clause 17. 10.2 The Supplier’s Request(s) For Payment Shall Be Made To The Procuring Entity In Writing, Accompanied By An Invoice Describing, As Appropriate, The Goods Delivered And/or Services Performed, And By Documents Submitted Pursuant To The Scc Provision For Gcc Clause 6.2, And Upon Fulfillment Of Other Obligations Stipulated In This Contract. 10.3 Pursuant To Gcc Clause 10.2, Payments Shall Be Made Promptly By The Procuring Entity, But In No Case Later Than Sixty (60) Days After Submission Of An Invoice Or Claim By The Supplier. 10.4 Unless Otherwise Specified In The Scc, The Currency In Which Payment Is Made To The Supplier Under This Contract Shall Be In Philippine Pesos. 11. Advance Payment 11.1 Advance Payment Shall Be Made Only After Prior Approval Of The President, And Shall Not Exceed Fifteen Percent (15%) Of The Contract Amount, Unless Otherwise Directed By The President Or In Cases Allowed Under Annex “d” Of Ra 9184. 11.2 For Goods Supplied From Abroad, The Terms Of Payment Shall Be As Follows: (a) On Contract Signature: Fifteen Percent (15%) Of The Contract Price Shall Be Paid Within Sixty (60) Days From Signing Of The Contract And Upon Submission Of A Claim And A Bank Guarantee For The Equivalent Amount Valid Until The Goods Are Delivered And In The Form Provided In Section Viii. Bidding Forms. (b) On Delivery: Sixty-five Percent (65%) Of The Contract Price Shall Be Paid To The Supplier Within Sixty (60) Days After The Date Of Receipt Of The Goods And Upon Submission Of The Documents (i) Through (vi) Specified In The Scc Provision On Delivery And Documents. (c) On Acceptance: The Remaining Twenty Percent (20%) Of The Contract Price Shall Be Paid To The Supplier Within Sixty (60) Days After The Date Of Submission Of The Acceptance And Inspection Certificate For The Respective Delivery Issued By The Procuring Entity’s Authorized Representative. In The Event That No Inspection Or Acceptance Certificate Is Issued By The Procuring Entity’s Authorized Representative Within Forty Five (45) Days Of The Date Shown On The Delivery Receipt The Supplier Shall Have The Right To Claim Payment Of The Remaining Twenty Percent (20%) Subject To The Procuring Entity’s Own Verification Of The Reason(s) For The Failure To Issue Documents (vii) And (viii) As Described In The Scc Provision On Delivery And Documents. 11.3 All Progress Payments Shall First Be Charged Against The Advance Payment Until The Latter Has Been Fully Exhausted. 12. Taxes And Duties The Supplier, Whether Local Or Foreign, Shall Be Entirely Responsible For All The Necessary Taxes, Stamp Duties, License Fees, And Other Such Levies Imposed For The Completion Of This Contract. 13. Performance Security 13.1 Unless Otherwise Specified In The Scc, Within Ten (10) Calendar Days From Receipt Of The Notice Of Award From The Procuring Entity But In No Case Later Than The Signing Of The Contract By Both Parties, The Successful Bidder Shall Furnish The Performance Security In Any The Forms Prescribed In The Itb Clause 33.2. 13.2 The Performance Security Posted In Favor Of The Procuring Entity Shall Be Forfeited In The Event It Is Established That The Winning Bidder Is In Default In Any Of Its Obligations Under The Contract. 13.3 The Performance Security Shall Remain Valid Until Issuance By The Procuring Entity Of The Certificate Of Final Acceptance. 13.4 Unless Otherwise Specified In The Scc, The Performance Security May Be Released By The Procuring Entity And Returned To The Supplier After The Issuance Of The Certificate Of Final Acceptance Subject To The Following Conditions. (a) There Are No Pending Claims Against The Supplier Or The Surety Company Filed By The Procuring Entity; (b) The Supplier Has No Pending Claims For Labor And Materials Filed Against It; And (c) Other Terms Specified In The Scc 13.5 In Case Of A Reduction Of The Contract Value, The Procuring Entity Shall Allow A Proportional Reduction In The Original Performance Security, Provided That Any Such Reduction Is More Than Ten Percent (10%) And That The Aggregate Of Such Reductions Is Not More Than Fifty Percent (50%) Of The Original Performance Security. 14. Use Of Contract Documents And Information 14.1 The Supplier Shall Not, Except For Purposes Of Performing The Obligations In This Contract, Without The Procuring Entity’s Prior Written Consent, Disclose This Contract, Or Any Provision Thereof, Or Any Specification, Plan, Drawing, Pattern, Sample, Or Information Furnished By Or On Behalf Of The Procuring Entity. Any Such Disclosure Shall Be Made In Confidence And Shall Extend Only As Far As May Be Necessary For Purposes Of Such Performance. 14.2 Any Document, Other Than This Contract Itself, Enumerated In Gcc Clause 14.1shall Remain The Property Of The Procuring Entity And Shall Be Returned (all Copies) To The Procuring Entity On Completion Of The Supplier’s Performance Under This Contract If So Required By The Procuring Entity. 15. Standards The Goods Provided Under This Contract Shall Conform To The Standards Mentioned In The Section Vii – Technical Specifications,; And, When No Applicable Standard Is Mentioned, To The Authoritative Standards Appropriate To The Goods’ Country Of Origin. Such Standards Shall Be The Latest Issued By The Institution Concerned. 16. Inspection And Tests 16.1 The Procuring Entity Or Its Representative Shall Have The Right To Inspect And/or To Test The Goods To Confirm Their Conformity To The Contract Specifications At No Extra Cost To The Procuring Entity. The Scc And Section Vii – Technical Specifications Shall Specify What Inspections And/or Tests The Procuring Entity Requires And Where They Are To Be Conducted. The Procuring Entity Shall Notify The Supplier In Writing, In A Timely Manner, Of The Identity Of Any Representatives Retained For These Purposes. 16.2 If Applicable, The Inspections And Tests May Be Conducted On The Premises Of The Supplier Or Its Subcontractor(s), At Point Of Delivery, And/or At The Goods’ Final Destination. If Conducted On The Premises Of The Supplier Or Its Subcontractor(s), All Reasonable Facilities And Assistance, Including Access To Drawings And Production Data, Shall Be Furnished To The Inspectors At No Charge To The Procuring Entity. 16.3 The Procuring Entity Or Its Designated Representative Shall Be Entitled To Attend The Tests And/or Inspections Referred To In This Clause Provided That The Procuring Entity Shall Bear All Of Its Own Costs And Expenses Incurred In Connection With Such Attendance Including, But Not Limited To, All Traveling And Board And Lodging Expenses. 16.4 The Procuring Entity May Reject Any Goods Or Any Part Thereof That Fail To Pass Any Test And/or Inspection Or Do Not Conform To The Specifications. The Supplier Shall Either Rectify Or Replace Such Rejected Goods Or Parts Thereof Or Make Alterations Necessary To Meet The Specifications At No Cost To The Procuring Entity, And Shall Repeat The Test And/or Inspection, At No Cost To The Procuring Entity, Upon Giving A Notice Pursuant To Gcc Clause 5. 16.5 The Supplier Agrees That Neither The Execution Of A Test And/or Inspection Of The Goods Or Any Part Thereof, Nor The Attendance By The Procuring Entity Or Its Representative, Shall Release The Supplier From Any Warranties Or Other Obligations Under This Contract. 17. Warranty 17.1 The Supplier Warrants That The Goods Supplied Under The Contract Are New, Unused, Of The Most Recent Or Current Models, And That They Incorporate All Recent Improvements In Design And Materials, Except When The Technical Specifications Required By The Procuring Entity Provides Otherwise. 17.2 The Supplier Further Warrants That All Goods Supplied Under This Contract Shall Have No Defect, Arising From Design, Materials, Or Workmanship Or From Any Act Or Omission Of The Supplier That May Develop Under Normal Use Of The Supplied Goods In The Conditions Prevailing In The Country Of Final Destination. 17.3 In Order To Assure That Manufacturing Defects Shall Be Corrected By The Supplier, A Warranty Shall Be Required From The Supplier For A Minimum Period Specified In The Scc. The Obligation For The Warranty Shall Be Covered By, At The Supplier’s Option, Either Retention Money In An Amount Equivalent To At Least One Percent (1%) Of Every Progress Payment, Or A Special Bank Guarantee Equivalent To At Least One Percent (1%) Of The Contract Price Or Other Such Amount If So Specified In Thescc. The Said Amounts Shall Only Be Released After The Lapse Of The Warranty Period Specified In The Scc; Provided, However, That The Supplies Delivered Are Free From Patent And Latent Defects And All The Conditions Imposed Under This Contract Have Been Fully Met. 17.4 The Procuring Entity Shall Promptly Notify The Supplier In Writing Of Any Claims Arising Under This Warranty. Upon Receipt Of Such Notice, The Supplier Shall, Within The Period Specified In The Scc And With All Reasonable Speed, Repair Or Replace The Defective Goods Or Parts Thereof, Without Cost To The Procuring Entity 17.5 If The Supplier, Having Been Notified, Fails To Remedy The Defect(s) Within The Period Specified In Gcc Clause 17.4, The Procuring Entity May Proceed To Take Such Remedial Action As May Be Necessary, At The Supplier’s Risk And Expense And Without Prejudice To Any Other Rights Which The Procuring Entity May Have Against The Supplier Under The Contract And Under The Applicable Law 18 Delays In The Supplier’s Performance 18.1 Delivery Of The Goods And/or Performance Of Services Shall Be Made By The Supplier In Accordance With The Time Schedule Prescribed By The Procuring Entity In Section Vi – Schedule Of Requirements. 18.2 If At Any Time During The Performance Of This Contract, The Supplier Or Its Subcontractor(s) Should Encounter Conditions Impeding Timely Delivery Of The Goods And/or Performance Of Services, The Supplier Shall Promptly Notify The Procuring Entity In Writing Of The Fact Of The Delay, Its Likely Duration And Its Cause(s). As Soon As Practicable After Receipt Of The Supplier’s Notice, And Upon Causes Provided For Under Gcc Clause 22, The Procuring Entity Shall Evaluate The Situation And May Extend The Supplier’s Time For Performance, In Which Case The Extension Shall Be Ratified By The Parties By Amendment Of Contract. 18.3 Except As Provided Under Gcc Clause 22, A Delay By The Supplier In The Performance Of Its Obligations Shall Render The Supplier Liable To The Imposition Of Liquidated Damages Pursuant To Gcc Clause 19, Unless An Extension Of Time Is Agreed Upon Pursuant To Gcc Clause 29 Without The Application Of Liquidated Damages. 19. Liquidated Damages Subject To Gcc Clause 18 And 22, If The Supplier Fails To Satisfactorily Deliver Any Or All Of The Goods And/or To Perform The Services Within The Period(s) Specified In This Contract Inclusive Of Duly Granted Time Extensions If Any, The Procuring Entity Shall, Without Prejudice To Its Other Remedies Under This Contract And Under The Applicable Law, Deduct From The Contract Price, As Liquidated Damages, A Sum Equivalent To The Percentage Specified In Thescc Of The Delivered Price Of The Delayed Goods Or Unperformed Services For Each Week Or Part Thereof Of Delay Until Actual Delivery Or Performance, Up To A Maximum Deduction Of The Percentage Specified In The Scc. Once The Maximum Is Reached, The Procuring Entity Shall Rescind The Contract Pursuant To Gcc Clause 23, Without Prejudice To Other Courses Of Action And Remedies Open To It. 20. Settlement Of Disputes 20.1 If Any Dispute Or Difference Of Any Kind Whatsoever Shall Arise Between The Procuring Entity And The Supplier In Connection With Or Arising Out Of This Contract, The Parties Shall Make Every Effort To Resolve Amicably Such Dispute Or Difference By Mutual Consultation. 20.2 If After Thirty (30) Days, The Parties Have Failed To Resolve Their Dispute Or Difference By Such Mutual Consultation, Then Either The Procuring Entity Or The Supplier May Give Notice To The Other Party Of Its Intention To Commence Arbitration, As Hereinafter Provided, As To The Matter In Dispute, And No Arbitration In Respect Of This Matter May Be Commenced Unless Such Notice Is Given. 20.3 Any Dispute Or Difference In Respect Of Which A Notice Of Intention To Commence Arbitration Has Been Given In Accordance With This Clause Shall Be Settled By Arbitration. Arbitration May Be Commenced Prior To Or After Delivery Of The Goods Under This Contract. 20.4 Arbitration Proceedings Shall Be Conducted In Accordance With The Rules Of Procedure Specified In The Scc. 20.5 Notwithstanding Any Reference To Arbitration Herein, The Parties Shall Continue To Perform Their Respective Obligations Under The Contract Unless They Otherwise Agree; And The Procuring Entity Shall Pay The Supplier Any Monies Due The Supplier. 21 Liability Of The Supplier 21.1 Subject To Additional Provisions, If Any, Set Forth In The Scc, The Supplier’s Liability Under This Contract Shall Be As Provided By The Laws Of The Republic Of The Philippines. 21.2 Except In Cases Of Criminal Negligence Or Willful Misconduct, And In The Case Of Infringement Of Patent Rights, If Applicable, The Aggregate Liability Of The Supplier To The Procuring Entity Shall Not Exceed The Total Contract Price, Provided That This Limitation Shall Not Apply To The Cost Of Repairing Or Replacing Defective Equipment. 22. Force Majeure 22.1 The Supplier Shall Not Be Liable For Forfeiture Of Its Performance Security, Liquidated Damages, Or Termination For Default If And To The Extent That Its Delay In Performance Or Other Failure To Perform Its Obligations Under The Contract Is The Result Of A Force Majeure. 22.2 For Purposes Of This Contract The Terms “force Majeure” And “fortuitous Event” May Be Used Interchangeably. In This Regard, A Fortuitous Event Or Force Majeure Shall Be Interpreted To Mean An Event Which The Contractor Could Not Have Foreseen, Or Which Though Foreseen, Was Inevitable. It Shall Not Include Ordinary Unfavorable Weather Conditions; And Any Other Cause The Effects Of Which Could Have Been Avoided With The Exercise Of Reasonable Diligence By The Contractor. 22.3 If A Force Majeure Situation Arises, The Supplier Shall Promptly Notify The Procuring Entity In Writing Of Such Condition And The Cause Thereof. Unless Otherwise Directed By The Procuring Entity In Writing, The Supplier Shall Continue To Perform Its Obligations Under The Contract As Far As Is Reasonably Practical, And Shall Seek All Reasonable Alternative Means For Performance Not Prevented By The Force Majeure. 23. Termination For Default 23.1 The Procuring Entity Shall Terminate This Contract For Default When Any Of The Following Conditions Attends Its Implementation. (a) Outside Of Force Majeure, The Supplier Fails To Deliver Or Perform Any Or All Of The Goods Within The Period(s) Specified In The Contract, Or Within Any Extension Thereof Granted By The Procuring Entity Pursuant To A Request Made By The Supplier Prior To The Delay, And Such Failure Amounts To At Least Ten Percent (10%) Of The Contact Price; (b) As A Result Of Force Majeure, The Supplier Is Unable To Deliver Or Perform Any Or All Of The Goods, Amounting To At Least Ten Percent (10%) Of The Contract Price, For A Period Of Not Less Than Sixty (60) Calendar Days After Receipt Of The Notice From The Procuring Entity Stating That The Circumstance Of Force Majeure Is Deemed To Have Ceased; Or (c) The Supplier Fails To Perform Any Other Obligation Under The Contract.. 23.2 In The Event The Procuring Entity Terminates This Contract In Whole Or In Part, For Any Of The Reasons Provided Under Gcc Clauses 23 To 26, The Procuring Entity May Procure, Upon Such Terms And In Such Manner As It Deems Appropriate, Goods Or Services Similar To Those Undelivered, And The Supplier Shall Be Liable To The Procuring Entity For Any Excess Costs For Such Similar Goods Or Services. However, The Supplier Shall Continue Performance Of This Contract To The Extent Not Terminated. 23.3 In Case The Delay In The Delivery Of The Goods And/or Performance Of The Services Exceeds A Time Duration Equivalent To Ten Percent (10%) Of The Specified Contract Time Plus Any Time Extension Duly Granted To The Supplier, The Procuring Entity May Terminate This Contract, Forfeit The Supplier's Performance Security And Award The Same To A Qualified Supplier. 24. Termination For Insolvency The Procuring Entity Shall Terminate This Contract If The Supplier Is Declared Bankrupt Or Insolvent As Determined With Finality By A Court Of Competent Jurisdiction. In This Event, Termination Will Be Without Compensation To The Supplier, Provided That Such Termination Will Not Prejudice Or Affect Any Right Of Action Or Remedy Which Has Accrued Or Will Accrue Thereafter To The Procuring Entity And/or The Supplier. 25. Termination For Convenience 25.1 The Procuring Entity May Terminate This Contract, In Whole Or In Part, At Any Time For Its Convenience. The Head Of The Procuring Entity May Terminate A Contract For The Convenience Of The Government If He Has Determined The Existence Of Conditions That Make Project Implementation Economically, Financially Or Technically Impractical And/or Unnecessary, Such As, But Not Limited To, Fortuitous Event(s) Or Changes In Law And National Government Policies. 25.2 The Goods That Have Been Delivered And/or Performed Or Are Ready For Delivery Or Performance Within Thirty (30) Calendar Days After The Supplier’s Receipt Of Notice To Terminate Shall Be Accepted By The Procuring Entity At The Contract Terms And Prices. For Goods Not Yet Performed And/or Ready For Delivery, The Procuring Entity May Elect: (a) To Have Any Portion Delivered And/or Performed And Paid At The Contract Terms And Prices; And/or (b) To Cancel The Remainder And Pay To The Supplier An Agreed Amount For Partially Completed And/or Performed Goods And For Materials And Parts Previously Procured By The Supplier. 25.3 If The Supplier Suffers Loss In Its Initial Performance Of The Terminated Contract, Such As Purchase Of Raw Materials For Goods Specially Manufactured For The Procuring Entity Which Cannot Be Sold In Open Market, It Shall Be Allowed To Recover Partially From This Contract, On A Quantum Meruit Basis. Before Recovery May Be Made, The Fact Of Loss Must Be Established Under Oath By The Supplier To The Satisfaction Of The Procuring Entity Before Recovery May Be Made. 26. Termination For Unlawful Acts 26.1 The Procuring Entity May Terminate This Contract In Case It Is Determined Prima Facie That The Supplier Has Engaged, Before Or During The Implementation Of This Contract, In Unlawful Deeds And Behaviors Relative To Contract Acquisition And Implementation. Unlawful Acts Include, But Are Not Limited To, The Following: (a) Corrupt, Fraudulent, And Coercive Practices As Defined In Itb Clause 3.1(a); (b) Drawing Up Or Using Forged Documents; (c) Using Adulterated Materials, Means Or Methods, Or Engaging In Production Contrary To Rules Of Science Or The Trade; And (d) Any Other Act Analogous To The Foregoing. 27. Procedures For Termination Of Contracts 27.1 The Following Provisions Shall Govern The Procedures For Termination Of This Contract: (a) Upon Receipt Of A Written Report Of Acts Or Causes Which May Constitute Ground(s) For Termination As Aforementioned, Or Upon Its Own Initiative, The Implementing Unit Shall, Within A Period Of Seven (7) Calendar Days, Verify The Existence Of Such Ground(s) And Cause The Execution Of A Verified Report, With All Relevant Evidence Attached; (b) Upon Recommendation By The Implementing Unit, The Head Of The Procuring Entity Shall Terminate This Contract Only By A Written Notice To The Supplier Conveying The Termination Of This Contract. The Notice Shall State: (i) That This Contract Is Being Terminated For Any Of The Ground(s) Afore-mentioned, And A Statement Of The Acts That Constitute The Ground(s) Constituting The Same; (ii) The Extent Of Termination, Whether In Whole Or In Part; (iii) An Instruction To The Supplier To Show Cause As To Why This Contract Should Not Be Terminated; (iv) Special Instructions Of The Procuring Entity, If Any. (c) The Notice To Terminate Shall Be Accompanied By A Copy Of The Verified Report; (d) Within A Period Of Seven (7) Calendar Days From Receipt Of The Notice Of Termination, The Supplier Shall Submit To The Head Of The Procuring Entity A Verified Position Paper Stating Why This Contract Should Not Be Terminated. If The Supplier Fails To Show Cause After The Lapse Of The Seven (7) Day Period, Either By Inaction Or By Default, The Head Of The Procuring Entity Shall Issue An Order Terminating This Contract; (e) The Procuring Entity May, At Anytime Before Receipt Of The Supplier’s Verified Position Paper To Withdraw The Notice To Terminate If It Is Determined That Certain Items Or Works Subject Of The Notice Had Been Completed, Delivered, Or Performed Before The Supplier’s Receipt Of The Notice; (f) Within A Non-extendible Period Of Ten (10) Calendar Days From Receipt Of The Verified Position Paper, The Head Of The Procuring Entity Shall Decide Whether Or Not To Terminate This Contract. It Shall Serve A Written Notice To The Supplier Of Its Decision And, Unless Otherwise Provided, This Contract Is Deemed Terminated From Receipt Of The Supplier Of The Notice Of Decision. The Termination Shall Only Be Based On The Ground(s) Stated In The Notice To Terminate; (g) The Head Of The Procuring Entity May Create A Contract Termination Review Committee (ctrc) To Assist Him In The Discharge Of This Function. All Decisions Recommended By The Ctrc Shall Be Subject To The Approval Of The Head Of The Procuring Entity; And (h) The Supplier Must Serve A Written Notice To The Procuring Entity Of Its Intention To Terminate The Contract At Least Thirty (30) Calendar Days Before Its Intended Termination. The Contract Is Deemed Terminated If It Is Not Resumed In Thirty (30) Calendar Days After The Receipt Of Such Notice By The Procuring Entity. 28. Assignment Of Rights The Supplier Shall Not Assign His Rights Or Obligations Under This Contract, In Whole Or In Part, Except With The Procuring Entity’s Prior Written Consent. 29. Contract Amendment Subject To Applicable Laws, No Variation In Or Modification Of The Terms Of This Contract Shall Be Made Except By Written Amendment Signed By The Parties. 30. Application These General Conditions Shall Apply To The Extent That They Are Not Superseded By Provisions Of Other Parts Of This Contract. Section V – Special Conditions Of Contract Scc Clause 1.1(g) The Procuring Entity Is The Local Government Of Badiangan, Iloilo. 1.1(i) The Supplier Is ________________________________. 1.1(j) The Funding Source Is Through The General Fund Of The Local Government Of Badiangan, Iloilo. The Total Approved Budget For The Contract Is Two Hundred Ninety One Thousand Five Hundred Eighty Five Pesos Only (p 291,585.00) 1.1(k) The Project Site Or The Delivery Of The Goods Shall Be At The Municipal Hall, Badiangan, Iloilo. 5.1 The Procuring Entity’s Address For Notices Is: Atty. Suzette A. Mamon Municipal Mayor Badiangan Municipal Hall R.c. Tabiana St., Poblacion, Badiangan, Iloilo 5033 Tel. No: Mayor’s Office (033-320-0807) 6.2 The Additional Requirements For The Completion Of This Contract Are As Follows: Delivery And Documents - For Purposes Of The Contract(s), “exw,” “fob,” “fca,” “cif,” “cip,” “ddp” And Other Trade Terms Used To Describe The Obligations Of The Parties Shall Have The Meanings Assigned To Them By The Current Edition Of Incoterms Published By The International Chamber Of Commerce, Paris. The Delivery Terms Of The Contract(s) Shall Be As Follows: For Domestic Suppliers, “the Delivery Terms Applicable To This Contract Are Delivered To The Municipal Hall, Badiangan, Iloilo. Risk And Title Will Pass From The Supplier To The Procuring Entity Upon Receipt And Final Acceptance Of The Goods At Their Final Destination.” Delivery Of The Goods Shall Be Made By The Supplier In Accordance With The Terms Specified In Section Vi – Schedule Of Requirements. The Details Of Shipping And/or Other Documents To Be Furnished By The Supplier Are As Follows: Upon Delivery Of Goods To The Project Site, The Supplier Shall Notify The Procuring Entity And Present The Following Documents To The Procuring Entity: (i) Original And Four Copies Of The Supplier’s Invoice Showing Goods’ Description, Quantity, Unit Price, And Total Amount; (ii) Original And Four Copies Delivery Receipt/note, Railway Receipt Or Truck Receipt; (iii) Original Supplier’s Factory Inspection Report; (iv) Original And Four Copies Of The Manufacturer’s And/or Supplier’s Warranty Certificate; (v) Original And Four Copies Of The Certificate Of Origin (for Imported Goods); (vi) Delivery Receipt Detailing Number And Description Of Items Received Signed By The Authorized Receiving Personnel; (vii) Certificate Of Acceptance/inspection Report Signed By The Procuring Entity’s Representative At The Project Site; And (viii) Four Copies Of The Invoice Receipt For Property Signed By The Procuring Entity’s Representative At The Project Site. For Purposes Of This Clause The Procuring Entity’s Representative At The Project Site Is Engr. Rosilia A. Villa, Municipal Engineer, Badiangan, Iloilo. Incidental Services - The Supplier Is Required To Provide All Of The Following Services, Including Additional Services, If Any, Specified In Section Vi – Schedule Of Requirements. (a) Performance Or Supervision Of On-site Assembly And/or Start Up Of The Supplied Goods; (b) Furnishing Of Tools Required For Assembly And/or Maintenance Of The Supplied Goods; (c) Furnishing Of A Detailed Operations And Maintenance Manual For Each Appropriate Unit Of The Supplied Goods; (d) Performance Or Supervision Or Maintenance And/or Repair Of The Supplied Goods, For A Period Of Time Agreed By The Parties, Provided That This Service Shall Not Relieve The Supplier Of Any Warranty Obligations Under This Contract; And (e) Training Of The Procuring Entity’s Personnel, At The Supplier’s Plant And/or On-site, In Assembly, Start-up, Operation, Maintenance, And/or Repair Of The Supplied Goods. The Contract Price For The Goods Shall Include The Prices Charged By The Supplier For Incidental Services And Shall Not Exceed The Prevailing Rates Charged To Other Parties By The Supplier For Similar Services. Insurance – The Goods Supplied Under This Contract Shall Be Fully Insured By The Supplier In A Freely Convertible Currency Against Loss Or Damage Incidental To Manufacture Or Acquisition, Transportation, Storage, And Delivery. The Goods Remain At The Risk And Title Of The Supplier Until Their Final Acceptance By The Procuring Entity. Transportation - Where The Supplier Is Required Under Contract To Deliver The Goods Cif, Cip Or Ddp, Transport Of The Goods To The Port Of Destination Or Such Other Named Place Of Destination In The Philippines, As Shall Be Specified In This Contract, Shall Be Arranged And Paid For By The Supplier, And The Cost Thereof Shall Be Included In The Contract Price. Where The Supplier Is Required Under Contract To Deliver The Goods Cif, Cip Or Ddp, Goods Are To Be Transported On Carriers Of Philippine Registry. In The Event That No Carrier Of Philippine Registry Is Available, Goods May Be Shipped By A Carrier Which Is Not Of Philippine Registry Provided That The Supplier Obtains And Presents To The Procuring Entity Certification To This Effect From The Nearest Philippine Consulate To The Port Of Dispatch. In The Event That Carriers Of Philippine Registry Are Available But Their Schedule Delays The Supplier In Its Performance Of This Contract The Period From When The Goods Were First Ready For Shipment And The Actual Date Of Shipment The Period Of Delay Will Be Considered Force Majeure In Accordance With Gcc Clause 22. The Procuring Entity Accepts No Liability For The Damage Of Goods During Transit Other Than Those Prescribed By Incoterms For Ddp Deliveries. In The Case Of Goods Supplied From Within The Philippines Or Supplied By Domestic Suppliers Risk And Title Will Not Be Deemed To Have Passed To The Procuring Entity Until Their Receipt And Final Acceptance At The Final Destination. Patent Rights - The Supplier Shall Indemnify The Procuring Entity Against All Third Party Claims Of Infringement Of Patent, Trademark, Or Industrial Design Rights Arising From Use Of The Goods Or Any Part Thereof. 9 Bid Prices Are Considered Fixed Prices, And Therefore Not Subject To Price Escalation During Contract Implementation, Except Under Extraordinary Circumstances And Upon Prior Approval Of The Gppb In Accordance With Section 61 Of R.a. 9184 And Its Irr-a. 10.1 No Further Instructions. 10.4 No Further Instructions. 13.1 No Further Instructions. 13.4 No Further Instructions. 13.4 (c) No Further Instructions. 16.1 The Inspection And Test That Will Be Conducted Is Physical Inspection. 17.3 The Goods Shall Have A Warranty Period Of Three (3) Months After Acceptance By The Procuring Entity Of The Delivered Goods Or After The Goods Are Consumed Whichever Is Earlier. 17.4 & 17.5 The Period For Correction Of Defects In The Warranty Period Is Seven (7) Calendar Days From Either Verbal Or Written Notification. 19 The Applicable Rate Is One Tenth (1/10) Of One (1) Percent Of The Cost Of The Unperformed Portion For Every Day Of Delay. The Maximum Deduction Shall Be Ten Percent (10%) Of The Amount Of Contract. Once The Cumulative Amount Of Liquidated Damages Reaches Ten Percent (10%) Of The Amount Of The Contract, The Procuring Entity Shall Rescind The Contract, Without Prejudice To Other Courses Of Action And Remedies Open To It. 20.4 In The Case Of A Dispute Between The Procuring Entity And The Supplier, The Dispute Shall Be Resolved In Accordance With Republic Act 9285 (“r.a. 9285”), Otherwise Known As The “alternative Dispute Resolution Act Of 2004.” 21.1 No Additional Provisions. Section Vi. Schedule Of Requirements The Delivery Schedule Expressed As Days/months Stipulates Hereafter A Delivery Date Which Is The Date Of Delivery To The Project Site Item No. Description Quantity Total Delivered, Days/months 1. Rope Light (yellow) 3 Rolls 3 Rolls 30 Calendar Days Upon Receipt Of P.o. 2. Rope Light (red) 3 Rolls 3 Rolls 30 Calendar Days Upon Receipt Of P.o. 3. Rope Light (green) 3 Rolls 3 Rolls 30 Calendar Days Upon Receipt Of P.o. 4. Led Bulb 1.5 Watts (red) 30 Pcs. 30 Pcs. 30 Calendar Days Upon Receipt Of P.o. 5. Led Bulb 1.5 Watts (yellow) 30 Pcs. 30 Pcs. 30 Calendar Days Upon Receipt Of P.o. 6. Led Bulb 1.5 Watts (green) 30 Pcs. 30 Pcs. 30 Calendar Days Upon Receipt Of P.o. 7. Rubber Receptacle 90 Pcs. 90 Pcs. 30 Calendar Days Upon Receipt Of P.o. 8. Cable Tie 4” 30 Packs. 30 Packs. 30 Calendar Days Upon Receipt Of P.o. 9. Cable Tie 5” 30 Packs. 30 Packs. 30 Calendar Days Upon Receipt Of P.o. 10. Christmas Lights Led Bulb 200 Pcs. 100 Pcs. 30 Calendar Days Upon Receipt Of P.o. 11. Thhn 5.5mm² 2 Boxes 2 Boxes 30 Calendar Days Upon Receipt Of P.o. 12. Cable Tie 12” 2 Packs. 2 Packs. 30 Calendar Days Upon Receipt Of P.o. 13. Electrical Tape, Big 30 Rolls 30 Rolls 30 Calendar Days Upon Receipt Of P.o. 14. Safety Breaker 30a 3 Sets 3 Sets 30 Calendar Days Upon Receipt Of P.o. 15. Safety Breaker 60a 2 Sets 2 Sets 30 Calendar Days Upon Receipt Of P.o. 16. Flat Cord #16 2 Rolls 2 Rolls 30 Calendar Days Upon Receipt Of P.o. 17. Flat Cord #18 3 Rolls 3 Rolls 30 Calendar Days Upon Receipt Of P.o. 18. Flat Bar 1/8x1/2 35 Lgths. 35 Lgths. 30 Calendar Days Upon Receipt Of P.o. 19. 10mmø Dsb 35 Lgths. 35 Lgths. 30 Calendar Days Upon Receipt Of P.o. 20. 9mmø Dsb 15 Lgths. 15 Lgths. 30 Calendar Days Upon Receipt Of P.o. 21. Plastic Rope #6 4 Rolls 4 Rolls 30 Calendar Days Upon Receipt Of P.o. 22. Welding Rod 10 Kgs. 10 Kgs. 30 Calendar Days Upon Receipt Of P.o. 23. Aluminum Paint 1 Gal. 1 Gal. 30 Calendar Days Upon Receipt Of P.o. 24. Paint Brush 2” 3 Pcs. 3 Pcs. 30 Calendar Days Upon Receipt Of P.o. 25. Paint Thinner 3 Btls. 3 Btls. 30 Calendar Days Upon Receipt Of P.o. 26. 1 ¼ G.i. Pipe Sched. 40 1 Length 1 Length 30 Calendar Days Upon Receipt Of P.o. 27. 1 ½ G.i. Pipe Sched. 40 1 Length 1 Length 30 Calendar Days Upon Receipt Of P.o. 28. #16 Tie Wire 5 Kgs. 5 Kgs. 30 Calendar Days Upon Receipt Of P.o. 29. Bolt 3/8x1 ½ W/ Nut And Washer 20 Pcs. 20 Pcs. 30 Calendar Days Upon Receipt Of P.o. 30. Drill Bit 3/8 (steel) 2 Pcs. 2 Pcs. 30 Calendar Days Upon Receipt Of P.o. 31. Bolt 3/8x4” W/ Nut And Washer 2 Pcs. 2 Pcs. 30 Calendar Days Upon Receipt Of P.o. 32. Convenience Outlet 3-gang 10 Sets 10 Sets 30 Calendar Days Upon Receipt Of P.o. 33. Plastic Screen 4x3/4 Hole (green) 50 Mtrs. 30 Mtrs. 30 Calendar Days Upon Receipt Of P.o. 34. Rope Light (white) 4 Rolls 4 Rolls 30 Calendar Days Upon Receipt Of P.o. 35. Drop Lights (white) 40 Boxes 40 Boxes 30 Calendar Days Upon Receipt Of P.o. 36. Led Strip Light (white) Single 3 Rolls 3 Rolls 30 Calendar Days Upon Receipt Of P.o. 37. Led Adaptor (single) 12 Pcs. 12 Pcs. 30 Calendar Days Upon Receipt Of P.o. 38. Led Controller (led Strip Lights) 6 Pcs. 6 Pcs. 30 Calendar Days Upon Receipt Of P.o. 39. Glue Stick, Big 60 Packs. 60 Packs. 30 Calendar Days Upon Receipt Of P.o. 40. Glue Stick, Small 100 Packs. 100 Packs. 30 Calendar Days Upon Receipt Of P.o. 41. Transparent Plastic Hose 1/2 15 Meters 15 Meters 30 Calendar Days Upon Receipt Of P.o. Name: ____________________________________________________________ Legal Capacity: _____________________________________________________ Signature: _________________________________________________________ Duly Authorized To Sign The Bid For And Behalf Of: ___________________________ Date: ___________________________________ Section Vii. Technical Specifications Note: In The Statement Of Compliance Column, Bidders Must State Here Either “comply” Or “not Comply” Against Each Of The Individual Parameters Of Each Specification Stating The Corresponding Performance Parameter Of The Goods Offered. Statements Of “comply” Or “not Comply” Must Be Supported By Evidence In A Bidders Bid And Cross-referenced To That Evidence. Evidence Shall Be In The Form Of Manufacturer’s Un-amended Sales Literature, Unconditional Statements Of Specification And Compliance Issued By The Manufacturer, Samples, Independent Test Data Etc., As Appropriate. A Statement That Is Not Supported By Evidence Or Is Subsequently Found To Be Contradicted By The Evidence Presented Will Render The Bid Under Evaluation Liable For Rejection. A Statement Either In The Bidders Statement Of Compliance Or The Supporting Evidence That Is Found To Be False Either During Bid Evaluation, Post-qualification Or The Execution Of The Contract May Be Regarded As Fraudulent And Render The Bidder Or Supplier Liable For Prosecution Subject To The Provisions Of Itb Clause 3.1(a)(ii) And/or Gcc Clause 2.1(a)(ii). Item No. Specifications Statement Of Compliance Cross Reference 1. Rope Light (yellow) 2. Rope Light (red) 3. Rope Light (green) 4. Led Bulb 1.5 Watts (red) 5. Led Bulb 1.5 Watts (yellow) 6. Led Bulb 1.5 Watts (green) 7. Rubber Receptacle 8. Cable Tie 4” 9. Cable Tie 5” 10. Christmas Lights Led Bulb 11. Thhn 5.5mm² 12. Cable Tie 12” 13. Electrical Tape, Big 14. Safety Breaker 30a 15. Safety Breaker 60a 16. Flat Cord #16 17. Flat Cord #18 18. Flat Bar 1/8x1/2 19. 10mmø Dsb 20. 9mmø Dsb 21. Plastic Rope #6 22. Welding Rod 23. Aluminum Paint 24. Paint Brush 2” 25. Paint Thinner 26. 1 ¼ G.i. Pipe Sched. 40 27. 1 ½ G.i. Pipe Sched. 40 28. #16 Tie Wire 29. Bolt 3/8x1 ½ W/ Nut And Washer 30. Drill Bit 3/8 (steel) 31. Bolt 3/8x4” W/ Nut And Washer 32. Convenience Outlet 3-gang 33. Plastic Screen 4x3/4 Hole (green) 34. Rope Light (white) 35. Drop Lights (white) 36. Led Strip Light (white) Single 37. Led Adaptor (single) 38. Led Controller (led Strip Lights) 39. Glue Stick, Big 40. Glue Stick, Small 41. Transparent Plastic Hose 1/2 \ Name: ____________________________________________________________ Legal Capacity: _____________________________________________________ Signature: _________________________________________________________ Duly Authorized To Sign The Bid For And Behalf Of: ___________________________ Date: ____________________________________ Section Viii. Bidding Forms Bid Form Date: Project Identification No.: To: [name And Address Of Procuring Entity] Gentlemen And/or Ladies: Having Examined The Philippine Bidding Documents (pbds) Including The Supplemental Or Bid Bulletin Numbers [insert Numbers], The Receipt Of Which Is Hereby Duly Acknowledged, We, The Undersigned, Offer To [supply/deliver/perform] [description Of The Goods] In Conformity With The Said Pbds For The Sum Of [total Bid Amount In Words And Figures] Or The Total Calculated Bid Price, As Evaluated And Corrected For Computational Errors, And Other Bid Modifications In Accordance With The Price Schedules Attached Herewith And Made Part Of This Bid. The Total Bid Price Includes The Cost Of All Taxes, Such As, But Not Limited To: [specify The Applicable Taxes, E.g. (i) Value Added Tax (vat), (ii) Income Tax, (iii) Local Taxes, And (iv) Other Fiscal Levies And Duties], Which Are Itemized Herein Or In The Price Schedules. We Undertake, If Our Bid Is Accepted, To Deliver The Goods In Accordance With The Delivery Schedule Specified In The Schedule Of Requirements. If Our Bid Is Accepted, We Undertake To Provide A Performance Security In The Form, Amounts, And Within The Times Specified In The Bidding Documents. We Agree To Abide By This Bid For The Bid Validity Period Specified In Bds Provision For Itb Clause 18.2 And It Shall Remain Binding Upon Us And May Be Accepted At Any Time Before The Expiration Of That Period. Commissions Or Gratuities, If Any, Paid Or To Be Paid By Us To Agents Relating To This Bid, And To Contract Execution If We Are Awarded The Contract, Are Listed Below: Name And Address Of Agent Amount And Currency Purpose Of Commission Or Gratuity (if None, State “none”) Until A Formal Contract Is Prepared And Executed, This Bid, Together With Your Written Acceptance Thereof And Your Notice Of Award, Shall Be Binding Upon Us. We Understand That You Are Not Bound To Accept The Lowest Calculated Bid, Or Any Bid You May Receive. We Certify/confirm That We Comply With The Eligibility Requirements As Per Itb Clause 5 Of The Bidding Documents. We Likewise Certify/ Confirm That The Undersigned, [ For Sole Proprietorships, Insert: As The Owner And Sole Proprietor Or Authorized Representative Of Name Of Bidder, Has The Full Power And Authority To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract, On The Latter's Behalf For The [name Of Project] Of The [name Of Procuring Entity] [for Partnerships, Corporations, Cooperatives, Or Joint Ventures, Insert: Is Granted Full Power And Authority By The Name Of Bidder, To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract On The Latter's Behalf For [name Of Project] Of The [name Of The Procuring Entity]. We Acknowledge That Failure To Sign Each And Every Page Of This Bid Form, Including The Attached Schedule Of Prices, Shall Be A Ground For The Rejection Of Our Bid. Dated This ________________ Day Of ________________ 20______. Name: ____________________________________________________________ Legal Capacity: _____________________________________________________ Signature: _________________________________________________________ Duly Authorized To Sign The Bid For And Behalf Of: ___________________________ Date: ____________________________________ For Goods Offered From Within The Philippines Name Of Bidder ____________________________ Project Identification No. __. Page Of . All Entries Must Be Computerized Or Typewritten 1 2 3 4 5 6 7 8 9 10 Item No. Description Country Of Origin Quantity Unit Unit Price Exw Per Item Transportation And Insurance And All Other Costs Incidental To Delivery, Per Item Sales And Other Taxes Payable If Contract Is Awarded, Per Item Cost Of Incidental Services, If Applicable, Per Item Total Price Per Unit (col 5 + 6 + 7 + 8) Total Price Delivered Final Destination (col. 9) X (col. 4) 1. Rope Light (yellow) 3 Rolls 2. Rope Light (red) 3 Rolls 3. Rope Light (green) 3 Rolls 4. Led Bulb 1.5 Watts (red) 30 Pcs. 5. Led Bulb 1.5 Watts (yellow) 30 Pcs. 6. Led Bulb 1.5 Watts (green) 30 Pcs. 7. Rubber Receptacle 90 Pcs. 8. Cable Tie 4” 30 Packs. 9. Cable Tie 5” 30 Packs. 10. Christmas Lights Led Bulb 200 Pcs. 11. Thhn 5.5mm² 2 Boxes 12. Cable Tie 12” 2 Packs. 13. Electrical Tape, Big 30 Rolls 14. Safety Breaker 30a 3 Sets 15. Safety Breaker 60a 2 Sets 16. Flat Cord #16 2 Rolls 17. Flat Cord #18 3 Rolls 18. Flat Bar 1/8x1/2 35 Lgths. 19. 10mmø Dsb 35 Lgths. 20. 9mmø Dsb 15 Lgths. 21. Plastic Rope #6 4 Rolls 22. Welding Rod 10 Kgs. 23. Aluminum Paint 1 Gal. 24. Paint Brush 2” 3 Pcs. 25. Paint Thinner 3 Btls. 26. 1 ¼ G.i. Pipe Sched. 40 1 Length 27. 1 ½ G.i. Pipe Sched. 40 1 Length 28. #16 Tie Wire 5 Kgs. 29. Bolt 3/8x1 ½ W/ Nut And Washer 20 Pcs. 30. Drill Bit 3/8 (steel) 2 Pcs. 31. Bolt 3/8x4” W/ Nut And Washer 2 Pcs. 32. Convenience Outlet 3-gang 10 Sets 33. Plastic Screen 4x3/4 Hole (green) 50 Mtrs. 34. Rope Light (white) 4 Rolls 35. Drop Lights (white) 40 Boxes 36. Led Strip Light (white) Single 3 Rolls 37. Led Adaptor (single) 12 Pcs. 38. Led Controller (led Strip Lights) 6 Pcs. 39. Glue Stick, Big 60 Packs. 40. Glue Stick, Small 100 Packs. 41. Transparent Plastic Hose 1/2 15 Meters Name: ____________________________________________________________ Legal Capacity: _____________________________________________________ Signature: _________________________________________________________ Duly Authorized To Sign The Bid For And Behalf Of: ___________________________ Omnibus Sworn Statement Republic Of The Philippines ) Iloilocity ) S.s. Affidavit I, [name Of Affiant], Of Legal Age, [civil Status], [nationality], And Residing At [address Of Affiant], After Having Been Duly Sworn In Accordance With Law, Do Hereby Depose And State That: 1. Select One, Delete The Other: If A Sole Proprietorship: I Am The Sole Proprietor Of [name Of Bidder] With Office Address At [address Of Bidder]; If A Partnership, Corporation, Cooperative, Or Joint Venture: I Am The Duly Authorized And Designated Representative Of [name Of Bidder] With Office Address At [address Of Bidder]; 2. Select One, Delete The Other: If A Sole Proprietorship: As The Owner And Sole Proprietor Of [name Of Bidder], I Have Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Represent It In The Bidding For [name Of The Project] Of The [name Of The Procuring Entity]; If A Partnership, Corporation, Cooperative, Or Joint Venture: I Am Granted Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary And/or To Represent The [name Of Bidder] In The Bidding As Shown In The Attached [state Title Of Attached Document Showing Proof Of Authorization (e.g., Duly Notarized Secretary’s Certificate Issued By The Corporation Or The Members Of The Joint Venture)]; 3. [name Of Bidder] Is Not “blacklisted” Or Barred From Bidding By The Government Of The Philippines Or Any Of Its Agencies, Offices, Corporations, Or Local Government Units, Foreign Government/foreign Or International Financing Institution Whose Blacklisting Rules Have Been Recognized By The Government Procurement Policy Board, By Itself Or By Relation, Membership, Association, Affiliation, Or Controlling Interest With Another Blacklisted Person Or Entity As Defined And Provided For In The Uniform Guidelines On Blacklisting; 4. Each Of The Documents Submitted In Satisfaction Of The Bidding Requirements Is An Authentic Copy Of The Original, Complete, And All Statements And Information Provided Therein Are True And Correct; 5. [name Of Bidder] Is Authorizing The Head Of The Procuring Entity Or Its Duly Authorized Representative(s) To Verify All The Documents Submitted; 6. Select One, Delete The Rest: If A Sole Proprietorship: I Am Not Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; If A Partnership Or Cooperative: None Of The Officers And Members Of [name Of Bidder] Is Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; If A Corporation Or Joint Venture: None Of The Officers, Directors, And Controlling Stockholders Of [name Of Bidder] Is Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; 7. [name Of Bidder] Complies With Existing Labor Laws And Standards; And 8. [name Of Bidder] Is Aware Of And Has Undertaken The Following Responsibilities As A Bidder: A) Carefully Examine All Of The Bidding Documents; B) Acknowledge All Conditions, Local Or Otherwise, Affecting The Implementation Of The Contract; C) Made An Estimate Of The Facilities Available And Needed For The Contract To Be Bid, If Any; And D) Inquire Or Secure Supplemental/bid Bulletin(s) Issued For The [name Of The Project]. 9. [name Of Bidder] Did Not Give Or Pay, Directly Or Indirectly, Any Commission, Amount, Fee, Or Any Form Of Consideration, Pecuniary Or Otherwise, To Any Person Or Official, Personnel Or Representative Of The Government In Relation To Any Procurement Project Or Activity. 10. In Case Advance Payment Was Made Or Given, Failure To Perform Or Deliver Any Of The Obligations And Undertakings In The Contract Shall Be Sufficient Grounds To Constitute Criminal Liability For Swindling (estafa) Or The Commission Of Fraud With Unfaithfulness Or Abuse Of Confidence Through Misappropriating Or Converting Any Payment Received By A Person Or Entity Under An Obligation Involving The Duty To Deliver Certain Goods Or Services, To The Prejudice Of The Public And The Government Of The Philippines Pursuant To Article 315 Of Act No. 3815 S, 1930, As Amended, Or The Revised Penal Code, In Witness Whereof, I Have Hereunto Set My Hand This __ Day Of ___, 20__ At ___________________________, Philippines. _____________________________________ Bidder’s Representative/authorized Signatory [jurat] Checklist Of Bid Requirements First Envelope Eligibility Documents Class “a” Documents Legal Documents: 1 Certificate Of Philgeps Registration (platinum Membership) And Membership With Annex A In Accordance With Section 8.5.2 Of The Revised Irr. Technical Documents: 2 Statement Of All Its On-going Government And Private Contracts Within The Last Two (2) Years From The Date Of Submission And Receipt Of Bids, Including Contracts Awarded But Not Yet Started, If Any, Which Are Similar In Nature And Complexity To The Contract To Be Bid. The Statement Shall Include, For Each Contract, The Following: (a) Name Of The Contract; (b) Date Of The Contract, (c) Kind Of Goods, (d) Amount Of And Value Of Outstanding Contracts, (e) Date Of Delivery, And (f) Notice Of Award, Notice To Proceed, Contract Of Agreements, Purchase Orders And Certificate Of Accomplishments Issued By The Owner. (latest) 3 Statement Of Its Single Largest Completed Contract (slcc) Which Includes Its Government And Private Contracts Within The Last Two (2) Years From The Date Of Submission And Receipt Of Bids, Which Are Similar In Nature And Complexity To The Contract To Be Bid. The Statement Shall Include, For Each Contract, The Following: (a) Name Of The Contract; (b) Date Of The Contract, (c) Kind Of Goods, (d) Amount Of And Value Of Awarded And Completed Contracts, (e) Date Of Delivery, (f) End User’s Acceptance And Or Official Receipt(s) Issued For The Contract Supported By Notice Of Award, Notice To Proceed, Contract/ Purchase Order, Certificate Of Completion And Certificate Of Acceptance.(latest) Financial Documents 4 The Prospective Bidder’s Latest Computation For Its Net Financial Contracting Capacity (nfcc) Which Must Be At Least Equal To The Abc To Be Bid. (latest) Or A Committed Line Of Credit From Universal Or Commercial Bank (not Applicable To Procurement Of Infrastructure Projects). Class “b” Documents 5 If Applicable, A Valid Joint Venture Agreement (jva) In Case The Joint Venture Is Already In Existence, Or, In Lieu Thereof, A Duly Notarized Statements From All The Potential Joint Venture Partners Stating That They Will Enter Into And Abide By The Provisions Of The Jva In The Instance That The Bid Is Successful Shall Be Included In The Bid . (latest) Technical Documents 1 2 Bid Security In The Prescribed Form, Amount And Validity Period And In Accordance With Itb Clause 18. Statement Of Compliance To The Schedule Of Requirements 3 4 Statement Of Compliance To Technical Specifications Taking Into Consideration The Notations Stated In Section Vii Of The Bidding Documents. Authority Of The Signatory 5 Sworn Statement By The Prospective Bidder Or Its Duly Authorized Representative In Accordance With Section 25.2(b)(iv) Of The Revised Irr Of Ra 9184 And As Indicated In The Omnibus Sworn Statement Of The Bidding Documents Using The Prescribed Form Issued By The Gppb. (latest) Note: Any Missing Document In The Above-mentioned Checklist Is A Ground For Outright Rejection Of The Bid Second Envelope Financial Documents 1 Financial Bid Form Which Includes Bid Prices And The Bill Of Quantities And The Applicable Price Schedules, In Accordance With Itb Clauses 15.1 And 15.4 And The Issued Form In Section Viii Of The Bidding Documents. 2 If A Bidder Claims Preference As A Domestic Bidder Or Domestic Entity, A Certification Issued By Dti (if A Bidder Is A Sole Proprietor), By Sec (if Bidder Is A Partnership, Or A Corporation); And Cda (if Bidder Is A Cooperative)issued In Accordance With Itb Clause 27, If Applicable, That: A) Sole Proprietor Is A Citizen Of The Philippines, Corporation, Cooperative, Or Association Is A Duly Organized Under The Laws Of The Philippines With At Least Seventy Five (75%) Of Its Interest Or Outstanding Capital Stock Belonging To Citizens Of The Philippines; B) Habitually Established In Business And Habitually Engaged In The Manufacturing Or Sale Of The Merchandise Covered By His Bid, And C) The Business Has Been In Existence For At Least Five (5) Consecutive Years Prior To The Advertisement And/or The Invitation To Bid.
Closing Soon25 Nov 2024
Tender AmountPHP 291.5 K (USD 4.9 K)
PKP S A Tender
Others
Poland
Details: Łódź, Ul. Dyspozytorska 4 - Replacement of Electrical Installation in Common Parts of a Residential Building. The Scope of Work Includes: 1. Replacement of Main Electrical Distribution Boards Together with Conversion Protections on Each Staircase (2 in total), 2. Installation of Power Limiters, 4. Replacement of Lighting Installation in Common Part of the Building (basement, Staircases), 5. Replacement of Electrical Installation Risers in Staircases - Cu3x6mm2 Cable. As part of the modernization of the electrical installation, it is planned to be performed in a Tn-cs system. The system should be performed in the common part of the building, leaving the possibility of eventual modernization in the network in the future to a full Tn-s system in each apartment.
Closing Soon27 Nov 2024
Tender AmountNA
Township of Divišov Tender
Others...+2Civil And Construction, Civil Works Others
Czech Republic
Details: The subject of the performance of the public contract is the revitalization of the square in Divišov, which consists in the reconstruction of the public space with the new construction of the shelter, retaining walls and in the vegetation management of the entire space. The implementation also includes the implementation of engineering networks (a new spine of rainwater drainage along the northern front of Horního and Tyršová Náměstí, which drains the relevant paved areas with street drains or gutters; a new public lighting system, including new cable routes; a ceremonial lighting system for the church, the Fallen Monument, and the historical well Electrification of Tyršov Square Square For The Purposes Of Municipal Events (drawer cabinets); Water Supply To The Planned Drinking Water And Hydrant On Tyršov Square; Repair Of Well On Tyršov Square.
Closing Date5 Dec 2024
Tender AmountCZK 71.4 Million (USD 2.9 Million)
Province Of Iloilo Tender
Agriculture or Forestry Works
Corrigendum : Closing Date Modified
Philippines
Details: Description Bids And Awards Committee Iloilo Provincial Government Procurement Of Agricultural Supplies Bid No. Agr-24-1657-b Philippine Bidding Documents Sixth Edition July 2020 Table Of Contents Section I. Invitation To Bid 3 Section Ii. Instructions To Bidders 5 1. Scope Of Bid 5 2. Funding Information 5 3. Bidding Requirements 5 4. Corrupt, Fraudulent, Collusive, And Coercive Practices 5 5. Eligible Bidders 5 6. Origin Of Goods 6 7. Subcontracts 7 8. Pre-bid Conference 7 9. Clarification And Amendment Of Bidding Documents 7 10. Documents Comprising The Bid: Eligibility And Technical Components 7 11. Documents Comprising The Bid: Financial Component 7 12. Bid Prices 8 13. Bid And Payment Currencies 8 14. Bid Security 8 15. Sealing And Marking Of Bids 9 16. Deadline For Submission Of Bids 9 17. Opening And Preliminary Examination Of Bids 9 18. Domestic Preference 9 19. Detailed Evaluation And Comparison Of Bids 9 20. Post-qualification 10 21. Signing Of The Contract 10 Section Iii. Bid Data Sheet 11 Section Iv. General Conditions Of Contract 12 1. Scope Of Contract 12 2. Advance Payment And Terms Of Payment 12 3. Performance Security 12 4. Inspection And Tests 12 5. Warranty 13 6. Liability Of The Supplier 13 Section V. Special Conditions Of Contract 14 Section Vi. Schedule Of Requirements 16 Section Vii. Technical Specifications 18 Section Viii. Checklist Of Technical And Financial Documents 20 Section I. Invitation To Bid Purchase Of Agricultural Supplies Bid No. Agr-24-1657-b 1. The Iloilo Provincial Government Through The General Fund 2024 Intends To Apply The Sum Of Seven Hundred Forty-seven Thousand One Hundred Forty Pesos (php 747,140.00) Being The Abc To Payments Under The Contract For The Purchase Of Agricultural Supplies. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. 2. The Iloilo Provincial Government Now Invites Bids For The Above Procurement Project. Delivery Of The Goods Is Required By 14 Days Upon Receipt Of The Notice To Proceed (ntp). Bidders Should Have Completed, Within Three (3) Years From The Date Of Submission And Receipt Of Bids, A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii (instructions To Bidders). 3. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using A Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) No. 9184. Bidding Is Restricted To Filipino Citizens/sole Proprietorships, Partnerships, Or Organizations With At Least Sixty Percent (60%) Interest Or Outstanding Capital Stock Belonging To Citizens Of The Philippines, And To Citizens Or Organizations Of A Country The Laws Or Regulations Of Which Grant Similar Rights Or Privileges To Filipino Citizens, Pursuant To Ra No. 5183. 4. Prospective Bidders May Obtain Further Information From The Bids And Awards Committee Secretariat Of The Iloilo Provincial Government And Inspect The Bidding Documents At The Address Given Below During 8:00 A.m. To 5:00 P.m. 5. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders On November 15, 2024 From The Given Address And Website(s) Below And Upon Payment Of The Applicable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb, In The Amount Of Five Hundred Pesos (php 500.00). The Procuring Entity Shall Allow The Bidder To Present Its Proof Of Payment For The Fees In Person. 6. The Iloilo Provincial Government Will Hold A Pre-bid Conference On N/a At 9:00 A.m. At The N/a And/or Through Video Conferencing Or Webcasting, Upon Request At Least Three (3) Days Before The Pre-bid Conference, Via Zoom Or Other Videoconferencing Portals, Which Shall Be Open To Prospective Bidders. 7. Bids Must Be Duly Received By The Bac Secretariat Through Manual Submission At The 5th Floor, Bac Secretariat Office, Iloilo Provincial Capitol, Iloilo City On Or Before November 25, 2024 At 9:00 A.m. Late Bids Shall Not Be Accepted. 8. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 14. 9. Bid Opening Shall Be On November 25, 2024 At 9:01 A.m.at The 5th Floor, Bac Secretariat Office, Iloilo Provincial Capitol, Iloilo City Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend The Activity. 10. A. The Participating Bidder/supplier Or Its Authorized Representative Must Indicate In Any Of The Eligibility Documents, An Email Address Or A Working Fax Number. The Absence Of Which Shall Be A Ground For Disqualification. Notice To The Bidder/supplier Through The Use Of Either Of These Means (email/fax) Is Considered Sufficient Notice. The Date Of Filing Of Reconsideration And All Communications With The Bac Shall Be Its (bac) Date Of Receipt. B. The Bidder(s)/awardee(s) Or Its Authorized Representative Must Conform To The Notice Of Award Within Three (3) Calendar Days From Receipt Of Such Notice And The Winning Bidder Shall Post The Required Performance Security And Enter Into Contract With The Procuring Entity Within Ten (10) Calendar Days From Receipt By The Winning Bidder Of The Notice Of Award In Accordance With Section 37.2.1 Of The Revised Irr Of R.a. No. 9184. C. The Bidder/supplier Must Have No Pending Unaccepted Notice To Proceed Three (3) Days From The Date Of Acceptance And Signing Of The Purchase Order. Otherwise, It Shall Be A Ground For Disqualification And The Bidder Will Be Rated "failed" During The Preliminary Examination Of Bids And/or Its Bid Shall Be Declared As "non-responsive" During Post-qualification. D. The Bidder/supplier Must Have No Notice Of Award Pending Its Conformity Three (3) Days From The Date Of Its Receipt Of The Notice Of Award. Otherwise, It Shall Be Aground For Disqualification And The Bidder Will Be Rated "failed" During The Preliminary Examination Of Bids And/or Its Bid Shall Be Declared As "non-responsive" During Post-qualification. E. The Bidder/supplier Shall Submit A List Of All Its Ongoing And Completed Projects With The Iloilo Provincial Government Indicating The Delivery Periods And Accomplishments Of Such Projects. F. The Bidder/supplier At The Time Of The Bidding Must Have No Pending Unposted Performance Or Warranty Security, As The Case May Be, Beyond The Period Allowed In The Notice Of Award. Otherwise, It Shall Be A Ground For Disqualification And The Bidder Will Be Rated "failed" During The Preliminary Examination Of Bids And/or Its Bid Shall Be Declared As "non-responsive" During Post-qualification. 11. The Iloilo Provincial Government Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Irr Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 12. For Further Information, Please Refer To: Atty. Raemman M. Lagrada Bac Secretariat Head 5th Floor, Bids And Awards Committee Iloilo Provincial Capitol Email Address: Ipg_bacs@yahoo.com Website: Iloilo.gov.ph Telephone Number: (033) 336-0736 13. You May Visit The Following Websites For Downloading Of Bidding Documents: Ipg.gov.ph And/or Philgeps.com October 11, 2024 Atty. Dennis T. Ventilacion Chairman, Bids And Awards Committee Section Ii. Instructions To Bidders 1. Scope Of Bid The Procuring Entity, Iloilo Provincial Government Wishes To Receive Bids For The Purchase Of Housekeeping Supplies With Bid No. Agr-24-1662-b. The Procurement Project (referred To Herein As “project”) Is Composed Of Twenty-eight (28) Item(s), The Details Of Which Are Described In Section Vii (technical Specifications). 2. Funding Information 2.1. The Gop Through The Source Of Funding As Indicated Below For 2024 In The Amount Of Seven Hundred Forty-seven Thousand One Hundred Forty Pesos (php 747,140.00) 2.2. The Source Of Funding Is: Lgus, The Annual Or Supplemental Budget, As Approved By The Sanggunian. 3. Bidding Requirements The Bidding For The Project Shall Be Governed By All The Provisions Of Ra No. 9184 And Its 2016 Revised Irr, Including Its Generic Procurement Manuals And Associated Policies, Rules And Regulations As The Primary Source Thereof, While The Herein Clauses Shall Serve As The Secondary Source Thereof. Any Amendments Made To The Irr And Other Gppb Issuances Shall Be Applicable Only To The Ongoing Posting, Advertisement, Or Ib By The Bac Through The Issuance Of A Supplemental Or Bid Bulletin. The Bidder, By The Act Of Submitting Its Bid, Shall Be Deemed To Have Verified And Accepted The General Requirements Of This Project, Including Other Factors That May Affect The Cost, Duration And Execution Or Implementation Of The Contract, Project, Or Work And Examine All Instructions, Forms, Terms, And Project Requirements In The Bidding Documents. 4. Corrupt, Fraudulent, Collusive, And Coercive Practices The Procuring Entity, As Well As The Bidders And Suppliers, Shall Observe The Highest Standard Of Ethics During The Procurement And Execution Of The Contract. They Or Through An Agent Shall Not Engage In Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices Defined Under Annex “i” Of The 2016 Revised Irr Of Ra No. 9184 Or Other Integrity Violations In Competing For The Project. 5. Eligible Bidders 5.1. Only Bids Of Bidders Found To Be Legally, Technically, And Financially Capable Will Be Evaluated. 5.2. A. Foreign Ownership Exceeding Those Allowed Under The Rules May Participate Pursuant To: I. When A Treaty Or International Or Executive Agreement As Provided In Section 4 Of The Ra No. 9184 And Its 2016 Revised Irr Allow Foreign Bidders To Participate; Ii. Citizens, Corporations, Or Associations Of A Country, Included In The List Issued By The Gppb, The Laws Or Regulations Of Which Grant Reciprocal Rights Or Privileges To Citizens, Corporations, Or Associations Of The Philippines; Iii. When The Goods Sought To Be Procured Are Not Available From Local Suppliers; Or Iv. When There Is A Need To Prevent Situations That Defeat Competition Or Restrain Trade. 5.3. Pursuant To Section 23.4.1.3 Of The 2016 Revised Irr Of Ra No.9184, The Bidder Shall Have An Slcc That Is At Least One (1) Contract Similar To The Project The Value Of Which, Adjusted To Current Prices Using The Psa’s Cpi, Must Be At Least Equivalent To: A. For The Procurement Of Non-expendable Supplies And Services: The Bidder Must Have Completed A Single Contract That Is Similar To This Project, Equivalent To At Least Fifty Percent (50%) Of The Abc. B. For The Procurement Of Expendable Supplies: The Bidder Must Have Completed A Single Contract That Is Similar To This Project, Equivalent To At Least Twenty-five Percent (25%) Of The Abc. C. For Procurement Where The Procuring Entity Has Determined, After The Conduct Of Market Research, That Imposition Of Either (a) Or (b) Will Likely Result To Failure Of Bidding Or Monopoly That Will Defeat The Purpose Of Public Bidding: The Bidder Should Comply With The Following Requirements: [select Either Failure Or Monopoly Of Bidding Based On Market Research Conducted] I. Completed At Least Two (2) Similar Contracts, The Aggregate Amount Of Which Should Be Equivalent To At Least Fifty Percent (50%) In The Case Of Non-expendable Supplies And Services Or Twenty-five Percent (25%) In The Case Of Expendable Supplies] Of The Abc For This Project; And Ii. The Largest Of These Similar Contracts Must Be Equivalent To At Least Half Of The Percentage Of The Abc As Required Above. 5.4. The Bidders Shall Comply With The Eligibility Criteria Under Section 23.4.1 Of The 2016 Irr Of Ra No. 9184. 6. Origin Of Goods There Is No Restriction On The Origin Of Goods Other Than Those Prohibited By A Decision Of The Un Security Council Taken Under Chapter Vii Of The Charter Of The Un, Subject To Domestic Preference Requirements Under Itb Clause 18. 7. Subcontracts 7.1. The Bidder May Subcontract Portions Of The Project To The Extent Allowed By The Procuring Entity As Stated Herein, But In No Case More Than Twenty Percent (20%) Of The Project. The Procuring Entity Has Prescribed That: Subcontracting Is Not Allowed. 8. Pre-bid Conference The Procuring Entity Will Hold A Pre-bid Conference For This Project On The Specified Date And Time And Either At Its Physical Address As Indicated In Paragraph 6 Of The Ib. 9. Clarification And Amendment Of Bidding Documents Prospective Bidders May Request For Clarification On And/or Interpretation Of Any Part Of The Bidding Documents. Such Requests Must Be In Writing And Received By The Procuring Entity, Either At Its Given Address Or Through Electronic Mail Indicated In The Ib, At Least Ten (10) Calendar Days Before The Deadline Set For The Submission And Receipt Of Bids. 10. Documents Comprising The Bid: Eligibility And Technical Components 10.1. The First Envelope Shall Contain The Eligibility And Technical Documents Of The Bid As Specified In Section Viii (checklist Of Technical And Financial Documents). 10.2. The Bidder’s Slcc As Indicated In Itb Clause 5.3 Should Have Been Completed Within Three (3) Years Prior To The Deadline For The Submission And Receipt Of Bids. 10.3. If The Eligibility Requirements Or Statements, The Bids, And All Other Documents For Submission To The Bac Are In Foreign Language Other Than English, It Must Be Accompanied By A Translation In English, Which Shall Be Authenticated By The Appropriate Philippine Foreign Service Establishment, Post, Or The Equivalent Office Having Jurisdiction Over The Foreign Bidder’s Affairs In The Philippines. Similar To The Required Authentication Above, For Contracting Parties To The Apostille Convention, Only The Translated Documents Shall Be Authenticated Through An Apostille Pursuant To Gppb Resolution No. 13-2019 Dated 23 May 2019. The English Translation Shall Govern, For Purposes Of Interpretation Of The Bid. 11. Documents Comprising The Bid: Financial Component 11.1. The Second Bid Envelope Shall Contain The Financial Documents For The Bid As Specified In Section Viii (checklist Of Technical And Financial Documents). 11.2. If The Bidder Claims Preference As A Domestic Bidder Or Domestic Entity, A Certification Issued By Dti Shall Be Provided By The Bidder In Accordance With Section 43.1.3 Of The 2016 Revised Irr Of Ra No. 9184. 11.3. Any Bid Exceeding The Abc Indicated In Paragraph 1 Of The Ib Shall Not Be Accepted. 11.4. For Foreign-funded Procurement, A Ceiling May Be Applied To Bid Prices Provided The Conditions Are Met Under Section 31.2 Of The 2016 Revised Irr Of Ra No. 9184. 12. Bid Prices 12.1. Prices Indicated On The Price Schedule Shall Be Entered Separately In The Following Manner: A. For Goods Offered From Within The Procuring Entity’s Country: I. The Price Of The Goods Quoted Exw (ex-works, Ex-factory, Ex-warehouse, Ex-showroom, Or Off-the-shelf, As Applicable); Ii. The Cost Of All Customs Duties And Sales And Other Taxes Already Paid Or Payable; Iii. The Cost Of Transportation, Insurance, And Other Costs Incidental To Delivery Of The Goods To Their Final Destination; And Iv. The Price Of Other (incidental) Services, If Any, Listed In E. B. For Goods Offered From Abroad: I. Unless Otherwise Stated In The Bds, The Price Of The Goods Shall Be Quoted Delivered Duty Paid (ddp) With The Place Of Destination In The Philippines As Specified In The Bds. In Quoting The Price, The Bidder Shall Be Free To Use Transportation Through Carriers Registered In Any Eligible Country. Similarly, The Bidder May Obtain Insurance Services From Any Eligible Source Country. Ii. The Price Of Other (incidental) Services, If Any, As Listed In Section Vii (technical Specifications). 13. Bid And Payment Currencies 13.1. For Goods That The Bidder Will Supply From Outside The Philippines, The Bid Prices May Be Quoted In The Local Currency Or Tradeable Currency Accepted By The Bsp At The Discretion Of The Bidder. However, For Purposes Of Bid Evaluation, Bids Denominated In Foreign Currencies, Shall Be Converted To Philippine Currency Based On The Exchange Rate As Published In The Bsp Reference Rate Bulletin On The Day Of The Bid Opening. 13.2. Payment Of The Contract Price Shall Be Made In: Philippine Pesos. 14. Bid Security 14.1. The Bidder Shall Submit A Bid Securing Declaration Or Any Form Of Bid Security In The Amount Indicated In The Bds, Which Shall Be Not Less Than The Percentage Of The Abc In Accordance With The Schedule In The Bds. 14.2. The Bid And Bid Security Shall Be Valid Until One Hundred Twenty (120) Days. Any Bid Not Accompanied By An Acceptable Bid Security Shall Be Rejected By The Procuring Entity As Non-responsive. 15. Sealing And Marking Of Bids Each Bidder Shall Submit One Copy Of The First And Second Components Of Its Bid. The Procuring Entity May Request Additional Hard Copies And/or Electronic Copies Of The Bid. However, Failure Of The Bidders To Comply With The Said Request Shall Not Be A Ground For Disqualification. 16. Deadline For Submission Of Bids 16.1. The Bidders Shall Submit On The Specified Date And Time At Its Physical Address As Indicated In Paragraph 7 Of The Ib. 17. Opening And Preliminary Examination Of Bids 17.1. The Bac Shall Open The Bids In Public At The Time, On The Date, And At The Place Specified In Paragraph 9 Of The Ib. The Bidders’ Representatives Who Are Present Shall Sign A Register Evidencing Their Attendance. In Case Videoconferencing, Webcasting Or Other Similar Technologies Will Be Used, Attendance Of Participants Shall Likewise Be Recorded By The Bac Secretariat. In Case The Bids Cannot Be Opened As Scheduled Due To Justifiable Reasons, The Rescheduling Requirements Under Section 29 Of The 2016 Revised Irr Of Ra No. 9184 Shall Prevail. 17.2. The Preliminary Examination Of Bids Shall Be Governed By Section 30 Of The 2016 Revised Irr Of Ra No. 9184. 18. Domestic Preference 18.1. The Procuring Entity Will Grant A Margin Of Preference For The Purpose Of Comparison Of Bids In Accordance With Section 43.1.2 Of The 2016 Revised Irr Of Ra No. 9184. 19. Detailed Evaluation And Comparison Of Bids 19.1. The Procuring Bac Shall Immediately Conduct A Detailed Evaluation Of All Bids Rated “passed,” Using Non-discretionary Pass/fail Criteria. The Bac Shall Consider The Conditions In The Evaluation Of Bids Under Section 32.2 Of The 2016 Revised Irr Of Ra No. 9184. 19.2. If The Project Allows Partial Bids, Bidders May Submit A Proposal On Any Of The Lots Or Items, And Evaluation Will Be Undertaken On A Per Lot Or Item Basis, As The Case Maybe. In This Case, The Bid Security As Required By Itb Clause 15 Shall Be Submitted For Each Lot Or Item Separately. 19.3. The Descriptions Of The Lots Or Items Shall Be Indicated In Section Vii (technical Specifications), Although The Abcs Of These Lots Or Items Are Indicated In The Bds For Purposes Of The Nfcc Computation Pursuant To Section 23.4.2.6 Of The 2016 Revised Irr Of Ra No. 9184. The Nfcc Must Be Sufficient For The Total Of The Abcs For All The Lots Or Items Participated In By The Prospective Bidder. 19.4. The Project Shall Be Awarded As Follows: Complete Bid - One Project Having Several Items That Shall Be Awarded As One Contract In Case Of Complete Bid. Line Bidding/partial Bidding - One Project Having Several Items, Which Shall Be Awarded As Separate Contracts Per Item 19.5. Except For Bidders Submitting A Committed Line Of Credit From A Universal Or Commercial Bank In Lieu Of Its Nfcc Computation, All Bids Must Include The Nfcc Computation Pursuant To Section 23.4.1.4 Of The 2016 Revised Irr Of Ra No. 9184, Which Must Be Sufficient For The Total Of The Abcs For All The Lots Or Items Participated In By The Prospective Bidder. For Bidders Submitting The Committed Line Of Credit, It Must Be At Least Equal To Ten Percent (10%) Of The Abcs For All The Lots Or Items Participated In By The Prospective Bidder. 20. Post-qualification Within A Non-extendible Period Of Five (5) Calendar Days From Receipt By The Bidder Of The Notice From The Bac That It Submitted The Lowest Calculated Bid, The Bidder Shall Submit Its Latest Income And Business Tax Returns Filed And Paid Through The Bir Electronic Filing And Payment System (efps) And Other Appropriate Licenses And Permits Required By Law And Stated In The Bds. 21. Signing Of The Contract 21.1. The Documents Required In Section 37.2 Of The 2016 Revised Irr Of Ra No. 9184 Shall Form Part Of The Contract. Additional Contract Documents Are Indicated In The Bds. Section Iii. Bid Data Sheet Itb Clause 5.3 For This Purpose, Contracts Similar To The Project Shall Be: A. Refers To The Contracts To Be Bid Or The Object Of The Contract; B. Completed Within Three (3) Years Prior To The Deadline For The Submission And Receipt Of Bids. 7.1 Subcontracting Is Not Allowed. 12 The Price Of The Goods Shall Be Quoted Ddp Art Center, Nanga, Pototan, Iloilo And Wvgnf, Calamigan, Concepcion, Iloilo Or The Applicable International Commercial Terms (incoterms) For This Project. 14.1 The Bid Security Shall Be In The Form Of A Bid Securing Declaration, Or Any Of The Following Forms And Amounts: A. The Amount Of Not Less Than Two Percent (2%) Of Abc, If Bid Security Is In Cash, Cashier’s/manager’s Check, Bank Draft/guarantee Or Irrevocable Letter Of Credit; Or B. The Amount Of Not Less Than Five Percent (5%) Of Abc, If Bid Security Is In Surety Bond. 15 Bidders Shall Prepare An Original Of The First (eligibility And Technical) And Second (financial) Envelopes. In Addition, Bidders Shall Submit Separate Copies Of The First And Second Envelopes (copy 1, Copy 2) And Each Set Of Documents Must Clearly Indicate Whether The Same Is Original, Copy 1, Or Copy 2. In The Event Of Any Discrepancy Between The Original And The Copies, The Original Shall Prevail. 19.3 No Further Instructions. 20.2 For The Procurement Of Drugs And Medicines And Medical Equipment/supplies, The Bidder Shall Submit The Following: A. Certificate Of Product Registration From Food And Drug Administration (fda) For Easy Validation During The Post-qualification; B. Certificate If Good Manufacturing Practice From Fda, For Easy Validation During The Post-qualification; C. Batch Release Certificate From Fda, For Easy Validation During The Post-qualification; D. If The Supplier Is Not The Manufacturer, Certification From The Manufacturer That The Supplier Is An Authorized Distributor/ Dealer Of The Products / Items For Easy Validation During The Post-qualification; E. For The Procurement Of Regulated Drugs, The Applicable Type Of S-license: S-1, S-3 (retailer) S-4 (wholesaler) S-5c (manufacturer) S-5d (bulk Depot/storage) S-5e S-5i (importer); F. License To Operate (lto) Issued By Fda, If Applicable; G. After-sales Services/parts, If Applicable; H. Manpower Requirements, If Applicable. 21.2 No Further Instructions. Section Iv. General Conditions Of Contract 1. Scope Of Contract This Contract Shall Include All Such Items, Although Not Specifically Mentioned, That Can Be Reasonably Inferred As Being Required For Its Completion As If Such Items Were Expressly Mentioned Herein. All The Provisions Of Ra No. 9184 And Its 2016 Revised Irr, Including The Generic Procurement Manual, And Associated Issuances, Constitute The Primary Source For The Terms And Conditions Of The Contract, And Thus, Applicable In Contract Implementation. Herein Clauses Shall Serve As The Secondary Source For The Terms And Conditions Of The Contract. This Is Without Prejudice To Sections 74.1 And 74.2 Of The 2016 Revised Irr Of Ra No. 9184 Allowing The Gppb To Amend The Irr, Which Shall Be Applied To All Procurement Activities, The Advertisement, Posting, Or Invitation Of Which Were Issued After The Effectivity Of The Said Amendment. Additional Requirements For The Completion Of This Contract Shall Be Provided In The Special Conditions Of Contract (scc). 2. Advance Payment And Terms Of Payment 2.1. Advance Payment Of The Contract Amount Is Provided Under Annex “d” Of The Revised 2016 Irr Of Ra No. 9184. 2.2. The Procuring Entity Is Allowed To Determine The Terms Of Payment On The Partial Or Staggered Delivery Of The Goods Procured, Provided Such Partial Payment Shall Correspond To The Value Of The Goods Delivered And Accepted In Accordance With Prevailing Accounting And Auditing Rules And Regulations. The Terms Of Payment Are Indicated In The Scc. 3. Performance Security Within Ten (10) Calendar Days From Receipt Of The Notice Of Award By The Bidder From The Procuring Entity But In No Case Later Than Prior To The Signing Of The Contract By Both Parties, The Successful Bidder Shall Furnish The Performance Security In Any Of The Forms Prescribed In Section 39 Of The 2016 Revised Irr Of Ra No. 9184. 4. Inspection And Tests The Procuring Entity Or Its Representative Shall Have The Right To Inspect And/or To Test The Goods To Confirm Their Conformity To The Project Specifications At No Extra Cost To The Procuring Entity In Accordance With The Generic Procurement Manual. In Addition To Tests In The Scc, Section Iv (technical Specifications) Shall Specify What Inspections And/or Tests The Procuring Entity Requires, And Where They Are To Be Conducted. The Procuring Entity Shall Notify The Supplier In Writing, In A Timely Manner, Of The Identity Of Any Representatives Retained For These Purposes. All Reasonable Facilities And Assistance For The Inspection And Testing Of Goods, Including Access To Drawings And Production Data, Shall Be Provided By The Supplier To The Authorized Inspectors At No Charge To The Procuring Entity. 5. Warranty 6.1. In Order To Assure That Manufacturing Defects Shall Be Corrected By The Supplier, A Warranty Shall Be Required From The Supplier As Provided Under Section 62.1 Of The 2016 Revised Irr Of Ra No. 9184. 6.2. The Procuring Entity Shall Promptly Notify The Supplier In Writing Of Any Claims Arising Under This Warranty. Upon Receipt Of Such Notice, The Supplier Shall, Repair Or Replace The Defective Goods Or Parts Thereof Without Cost To The Procuring Entity, Pursuant To The Generic Procurement Manual. 6. Liability Of The Supplier The Supplier’s Liability Under This Contract Shall Be As Provided By The Laws Of The Republic Of The Philippines. If The Supplier Is A Joint Venture, All Partners To The Joint Venture Shall Be Jointly And Severally Liable To The Procuring Entity. Section V. Special Conditions Of Contract Gcc Clause 1 Delivery And Documents – For Purposes Of The Contract, “exw,” “fob,” “fca,” “cif,” “cip,” “ddp” And Other Trade Terms Used To Describe The Obligations Of The Parties Shall Have The Meanings Assigned To Them By The Current Edition Of Incoterms Published By The International Chamber Of Commerce, Paris. The Delivery Terms Of This Contract Shall Be As Follows: [for Goods Supplied From Within The Philippines, State:] “the Delivery Terms Applicable To This Contract Are Delivered To The Art Center, Nanga, Pototan, Iloilo And Wvgnf, Calamigan, Concepcion, Iloilo. Risk And Title Will Pass From The Supplier To The Procuring Entity Upon Receipt And Final Acceptance Of The Goods At Their Final Destination.” Delivery Of The Goods Shall Be Made By The Supplier In Accordance With The Terms Specified In Section Vi (schedule Of Requirements). For Purposes Of This Clause The Procuring Entity’s Representative At The Project Site Is The Authorized Employee/official Of The Iloilo Provincial Government. Incidental Services – The Supplier Is Required To Provide All Of The Following Services, Including Additional Services, If Any, Specified In Section Vi. Schedule Of Requirements: A. Performance Or Supervision Of On-site Assembly And/or Start-up Of The Supplied Goods; B. Furnishing Of Tools Required For Assembly And/or Maintenance Of The Supplied Goods; C. Furnishing Of A Detailed Operations And Maintenance Manual For Each Appropriate Unit Of The Supplied Goods; The Contract Price For The Goods Shall Include The Prices Charged By The Supplier For Incidental Services And Shall Not Exceed The Prevailing Rates Charged To Other Parties By The Supplier For Similar Services. Packaging – The Supplier Shall Provide Such Packaging Of The Goods As Is Required To Prevent Their Damage Or Deterioration During Transit To Their Final Destination, As Indicated In This Contract. The Packaging Shall Be Sufficient To Withstand, Without Limitation, Rough Handling During Transit And Exposure To Extreme Temperatures, Salt And Precipitation During Transit, And Open Storage. Packaging Case Size And Weights Shall Take Into Consideration, Where Appropriate, The Remoteness Of The Goods’ Final Destination And The Absence Of Heavy Handling Facilities At All Points In Transit. The Packaging, Marking, And Documentation Within And Outside The Packages Shall Comply Strictly With Such Special Requirements As Shall Be Expressly Provided For In The Contract, Including Additional Requirements, If Any, Specified Below, And In Any Subsequent Instructions Ordered By The Procuring Entity. The Outer Packaging Must Be Clearly Marked On At Least Four (4) Sides As Follows: Name Of The Procuring Entity Name Of The Supplier Contract Description Final Destination Gross Weight Any Special Lifting Instructions Any Special Handling Instructions A Packaging List Identifying The Contents And Quantities Of The Package Is To Be Placed On An Accessible Point Of The Outer Packaging If Practical. If Not Practical The Packaging List Is To Be Placed Inside The Outer Packaging But Outside The Secondary Packaging. Transportation – Where The Supplier Is Required Under Contract To Deliver The Goods Cif, Cip, Or Ddp, Transport Of The Goods To The Port Of Destination Or Such Other Named Place Of Destination In The Philippines, As Shall Be Specified In This Contract, Shall Be Arranged And Paid For By The Supplier, And The Cost Thereof Shall Be Included In The Contract Price. Where The Supplier Is Required Under This Contract To Transport The Goods To A Specified Place Of Destination Within The Philippines, Defined As The Project Site, Transport To Such Place Of Destination In The Philippines, Including Insurance And Storage, As Shall Be Specified In This Contract, Shall Be Arranged By The Supplier, And Related Costs Shall Be Included In The Contract Price. Where The Supplier Is Required Under Contract To Deliver The Goods Cif, Cip Or Ddp, Goods Are To Be Transported On Carriers Of Philippine Registry. In The Event That No Carrier Of Philippine Registry Is Available, Goods May Be Shipped By A Carrier Which Is Not Of Philippine Registry Provided That The Supplier Obtains And Presents To The Procuring Entity Certification To This Effect From The Nearest Philippine Consulate To The Port Of Dispatch. In The Event That Carriers Of Philippine Registry Are Available But Their Schedule Delays The Supplier In Its Performance Of This Contract The Period From When The Goods Were First Ready For Shipment And The Actual Date Of Shipment The Period Of Delay Will Be Considered Force Majeure. The Procuring Entity Accepts No Liability For The Damage Of Goods During Transit Other Than Those Prescribed By Incoterms For Ddp Deliveries. In The Case Of Goods Supplied From Within The Philippines Or Supplied By Domestic Suppliers Risk And Title Will Not Be Deemed To Have Passed To The Procuring Entity Until Their Receipt And Final Acceptance At The Final Destination. 2.2 Partial Payment Is Not Allowed. 4 The Inspections And Tests That Will Be Conducted Are Through Physical Inspection. Section Vi. Schedule Of Requirements The Delivery Schedule Expressed As Weeks/months Stipulates Hereafter A Delivery Date Which Is The Date Of Delivery To The Project Site. Item Number Description Quantity Total Delivered, Weeks/months 1 Plastic Blue Drum. Open-head With Lid And Ring Lock (200 Liter Minimum Capacity) 211 211 2 Bolo, 16" Minimum Length 12 12 3 Impulse Sealer, 12" Minimum Length 5 5 4 Cane Machete 12 12 5 Spade 12 12 6 Wheel Barrow (wide Type, Gauge 20) 60 Liters Minimum Capacity, 13" X 3", Solid Wheel/tire (shallow Type}) 9 9 7 Heavy Duty Cable Reel Extension (50 Meters Minimum Length) 5 5 8 Stainless Steel Toolbox 20" (470mm X 220mm X 220mm) (l X W X H) 3 3 9 Socket Wrench (26pcs Set, 1/2" Drive 10", Point Socket Wrench: 6-12mm With 08, 09, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 24. 27,30, 32mm Ratchet 2 2 10 Pipe Wrench 14’’ (350mm) Maximum Clamping Diameter 50mm 3 3 11 Pruning Shears 7 1/2" 7 7 12 Electric Wire Thhn (thermoplastic High Heat-resistant Nylon) Stranded Cable #12, 150 Meter/roll 2 2 13 Polypropylene Plastic 5"' X 12" X 025mm (thickness) 30 30 14 Gi Wire #16 5 5 15 Sdr 11 Hdpe Black Pipe 1 Inch (141 Meter/roll) 5 5 16 Garden Hose 3/4" (60 Meters/roll) 6 6 17 Chemical Hose 3/4" (50 Meters/roll) 6 6 18 Good Lumber (2" X 6" X 10') 8 8 19 Good Lumber 2" X 3" X 10') 8 8 20 Gi Pipe 1 1/2" Diameter, Schedule 40, 6 Meter Length 7 7 21 Raincoat (medium: 5pcs, Large: 5pcs, X-large:6pcs, Xx-large: 4pcs) 20 20 22 Rubber Boots (medium: 7pcs,large: 7pcs, X-large: 6pcs) 20 20 23 Plastic Seal Cloth & Filament (12" Minimum Length) 30 30 24 Stainless Caserole With Cover (34 Cm Minimum Diameter) 5 5 25 Rake (wooden Handle) 7 7 26 Universal Al Gun (for Cattle) (0.25/0.5cc) (stainless Steel) 5 5 27 Fiber Glass Syringe (20ml) 10 10 28 Nylon Rope No. 16 (200meters/roll) 10 10 ___________________________________ Signature Over Printed Name Section Vii. Technical Specifications Bid No.: Agr-24-1657-b Item Specification Statement Of Compliance [bidders Must State Here Either “comply” Or “not Comply” Against Each Of The Individual Parameters Of Each Specification Stating The Corresponding Performance Parameter Of The Equipment Offered. Statements Of “comply” Or “not Comply” Must Be Supported By Evidence In A Bidders Bid And Cross-referenced To That Evidence. Evidence Shall Be In The Form Of Manufacturer’s Un-amended Sales Literature, Unconditional Statements Of Specification And Compliance Issued By The Manufacturer, Samples, Independent Test Data Etc., As Appropriate. A Statement That Is Not Supported By Evidence Or Is Subsequently Found To Be Contradicted By The Evidence Presented Will Render The Bid Under Evaluation Liable For Rejection. A Statement Either In The Bidder's Statement Of Compliance Or The Supporting Evidence That Is Found To Be False Either During Bid Evaluation, Post-qualification Or The Execution Of The Contract May Be Regarded As Fraudulent And Render The Bidder Or Supplier Liable For Prosecution Subject To The Applicable Laws And Issuances.] 1. Plastic Blue Drum. Open-head With Lid And Ring Lock (200 Liter Minimum Capacity) 2. Bolo, 16" Minimum Length 3. Impulse Sealer, 12" Minimum Length 4. Cane Machete 5. Spade 6. Wheel Barrow (wide Type, Gauge 20) 60 Liters Minimum Capacity, 13" X 3", Solid Wheel/tire (shallow Type}) 7. Heavy Duty Cable Reel Extension (50 Meters Minimum Length) 8. Stainless Steel Toolbox 20" (470mm X 220mm X 220mm) (l X W X H) 9. Socket Wrench (26pcs Set, 1/2" Drive 10", Point Socket Wrench: 6-12mm With 08, 09, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 24. 27,30, 32mm Ratchet 10. Pipe Wrench 14’’ (350mm) Maximum Clamping Diameter 50mm 11. Pruning Shears 7 1/2" 12. Electric Wire Thhn (thermoplastic High Heat-resistant Nylon) Stranded Cable #12, 150 Meter/roll 13. Polypropylene Plastic 5"' X 12" X 025mm (thickness) 14. Gi Wire #16 15. Sdr 11 Hdpe Black Pipe 1 Inch (141 Meter/roll) 16. Garden Hose 3/4" (60 Meters/roll) 17. Chemical Hose 3/4" (50 Meters/roll) 18. Good Lumber (2" X 6" X 10') 19. Good Lumber 2" X 3" X 10') 20. Gi Pipe 1 1/2" Diameter, Schedule 40, 6 Meter Length 21. Raincoat (medium: 5pcs, Large: 5pcs, X-large:6pcs, Xx-large: 4pcs) 22. Rubber Boots (medium: 7pcs,large: 7pcs, X-large: 6pcs) 23. Plastic Seal Cloth & Filament (12" Minimum Length) 24. Stainless Caserole With Cover (34 Cm Minimum Diameter) 25. Rake (wooden Handle) 26. Universal Al Gun (for Cattle) (0.25/0.5cc) (stainless Steel) 27. Fiber Glass Syringe (20ml) 28. Nylon Rope No. 16 (200meters/roll) Terms And Conditions 1. All Items Must Be Delivered At Art Center, Nanga, Pototan, Iloilo Except For Item No. 1 Which Will Be Delivered At Wvgnf, Calamigan, Concepcion, Iloilo 2. All Items Must Be Delivered Within 14 Days Upon Receipt Of Notice To Proceed (ntp) 3. All Items Must Be Delivered At Their Best Quality And Condition 4. Winning Bidder Must Coordinate With Provincial Agriculture Office, Livestock Division Prior To The Delivery Of Items Listed Above ___________________________________ Signature Over Printed Name Section Viii. Checklist Of Technical And Financial Documents I. Technical Component Envelope Class “a” Documents Legal Documents ⬜ (a) Valid Philgeps Registration Certificate (platinum Membership) (all Pages);or ⬜ (b) Registration Certificate From Securities And Exchange Commission (sec), Department Of Trade And Industry (dti) For Sole Proprietorship, Or Cooperative Development Authority (cda) For Cooperatives Or Its Equivalent Document, And ⬜ (c) Mayor’s Or Business Permit Issued By The City Or Municipality Where The Principal Place Of Business Of The Prospective Bidder Is Located, Or The Equivalent Document For Exclusive Economic Zones Or Areas; And ⬜ (d) Tax Clearance Per E.o. No. 398, S. 2005, As Finally Reviewed And Approved By The Bureau Of Internal Revenue (bir). Technical Documents ⬜ (e) Statement Of The Prospective Bidder Of All Its Ongoing Government And Private Contracts, Including Contracts Awarded But Not Yet Started, If Any, Whether Similar Or Not Similar In Nature And Complexity To The Contract To Be Bid; And ⬜ (f) Statement Of The Bidder’s Single Largest Completed Contract (slcc) Similar To The Contract To Be Bid, Except Under Conditions Provided For In Sections 23.4.1.3 And 23.4.2.4 Of The 2016 Revised Irr Of Ra No. 9184, Within The Relevant Period As Provided In The Bidding Documents; And ⬜ (g) Original Copy Of Bid Security. If In The Form Of A Surety Bond, Submit Also A Certification Issued By The Insurance Commission; Or Original Copy Of Notarized Bid Securing Declaration; And ⬜ (h) Conformity With The Technical Specifications, Which May Include Production/delivery Schedule, Manpower Requirements, And/or After-sales/parts, If Applicable; And ⬜ (i) Original Duly Signed Omnibus Sworn Statement (oss); And If Applicable, Original Notarized Secretary’s Certificate In Case Of A Corporation, Partnership, Or Cooperative; Or Original Special Power Of Attorney Of All Members Of The Joint Venture Giving Full Power And Authority To Its Officer To Sign The Oss And Do Acts To Represent The Bidder. Financial Documents ⬜ (j) The Supplier’s Audited Financial Statements, Showing, Among Others, The Supplier’s Total And Current Assets And Liabilities, Stamped “received” By The Bir Or Its Duly Accredited And Authorized Institutions, For The Preceding Calendar Year Which Should Not Be Earlier Than Two (2) Years From The Date Of Bid Submission; And ⬜ (k) The Prospective Bidder’s Computation Of Net Financial Contracting Capacity (nfcc); Or A Committed Line Of Credit From A Universal Or Commercial Bank In Lieu Of Its Nfcc Computation. Class “b” Documents ⬜ (l) If Applicable, A Duly Signed Joint Venture Agreement (jva) In Case The Joint Venture Is Already In Existence; Or Duly Notarized Statements From All The Potential Joint Venture Partners Stating That They Will Enter Into And Abide By The Provisions Of The Jva In The Instance That The Bid Is Successful. Ii. Financial Component Envelope ⬜ (m) Original Of Duly Signed And Accomplished Financial Bid Form; And ⬜ (n) Original Of Duly Signed And Accomplished Price Schedule(s). Other Documentary Requirements Under Ra No. 9184 (as Applicable) ⬜ (o) [for Foreign Bidders Claiming By Reason Of Their Country’s Extension Of Reciprocal Rights To Filipinos] Certification From The Relevant Government Office Of Their Country Stating That Filipinos Are Allowed To Participate In Government Procurement Activities For The Same Item Or Product. ⬜ (p) Certification From The Dti If The Bidder Claims Preference As A Domestic Bidder Or Domestic Entity. Bid Form Date: _____________________ Bid No.: ___________________ To: Bids And Awards Committee Iloilo Provincial Government Iloilo Provincial Capitol Bonifacio Drive, Iloilo City Having Examined The Philippine Bidding Documents (pbds) Including The Supplemental Or Bid Bulletin Numbers __________, The Receipt Of Which Is Hereby Duly Acknowledged, We, The Undersigned, Offer To Supply/deliver/perform _________________________________________ [description Of The Goods] In Conformity With The Said Pbds For The Sum Of _______________________________________, (php _______________________) [total Bid Amount In Words And Figures] Or The Total Calculated Bid Price, As Evaluated And Corrected For Computational Errors, And Other Bid Modifications In Accordance With The Price Schedules Attached Herewith And Made Part Of This Bid. The Total Bid Price Includes The Cost Of All Taxes, Such As, But Not Limited To: Value Added Tax (vat), Income Tax, Local Taxes, And Other Fiscal Levies And Duties, As Applicable, Which Are Itemized Herein Or In The Price Schedules, If Our Bid Is Accepted, We Undertake: A. To Deliver The Goods In Accordance With The Delivery Schedule Specified In The Schedule Of Requirements Of The Philippine Bidding Documents (pbds); B. To Provide A Performance Security In The Form, Amounts, And Within The Times Prescribed In The Pbds; C. To Abide By The Bid Validity Period Specified In The Pbds And It Shall Remain Binding Upon Us At Any Time Before The Expiration Of That Period. Until A Formal Contract Is Prepared And Executed, This Bid, Together With Your Written Acceptance Thereof And Your Notice Of Award, Shall Be Binding Upon Us. We Understand That You Are Not Bound To Accept The Lowest Calculated Bid Or Any Bid You May Receive. We Certify/confirm That We Comply With The Eligibility Requirements Pursuant To The Pbds. The Undersigned Is Authorized To Submit The Bid On Behalf Of ____________________________________________________ As Evidenced By The Attached [name Of The Bidder] ______________________________________. [state The Written Authority]. We Acknowledge That Failure To Sign Each And Every Page Of This Bid Form, Including The Schedule Of Prices, Shall Be A Ground For The Rejection Of Our Bid. Name: Legal Capacity: Signature: Duly Authorized To Sign The Bid For And Behalf Of: Date: Republic Of The Philippines) City Of ____________________) S.s. Bid Securing Declaration Bid No.: ___________________________ To: Bids And Awards Committee Iloilo Provincial Government Iloilo Provincial Capitol Bonifacio Drive, Iloilo City I/we, The Undersigned, Declare That: 1. I/we Understand That, According To Your Conditions, Bids Must Be Supported By A Bid Security, Which May Be In The Form Of A Bid Securing Declaration. 2. I/we Accept That: (a) I/we Will Be Automatically Disqualified From Bidding For Any Procurement Contract With Any Procuring Entity For A Period Of Two (2) Years Upon Receipt Of Your Blacklisting Order; And, (b) I/we Will Pay The Applicable Fine Provided Under Section 6 Of The Guidelines On The Use Of Bid Securing Declaration, Within Fifteen (15) Days From Receipt Of The Written Demand By The Procuring Entity For The Commission Of Acts Resulting To The Enforcement Of The Bid Securing Declaration Under Sections 23.1(b), 34.2, 40.1 And 69.1, Except 69.1(f),of The Irr Of Ra No. 9184; Without Prejudice To Other Legal Action The Government May Undertake. 3. I/we Understand That This Bid Securing Declaration Shall Cease To Be Valid On The Following Circumstances: A. Upon Expiration Of The Bid Validity Period, Or Any Extension Thereof Pursuant To Your Request; B. I Am/we Are Declared Ineligible Or Post-disqualified Upon Receipt Of Your Notice To Such Effect, And (i) I/we Failed To Timely File A Request For Reconsideration Or (ii) I/we Filed A Waiver To Avail Of Said Right; And C. I Am/we Are Declared The Bidder With The Lowest Calculated Responsive Bid, And I/we Have Furnished The Performance Security And Signed The Contract. In Witness Whereof, I/we Have Hereunto Set My/our Hand/s This ______ __ At ___________________________. _________________________________________________ [signature Over Printed Name Of Bidder Or Its Authorized Representative] [insert Signatory’s Legal Capacity] Subscribed And Sworn To Before Me, _______________________ In The _____________________. Affiant Exhibited To Me His Valid Identification Card With Id No. _________________ Issued By: ___________________. Doc No.:______; Page No. _____; Book No.:_____; Series Of: _____; Republic Of The Philippines) City Of _____________________) S.s. Omnibus Sworn Statement (for Sole Proprietorship) I, _______________________________________of Legal Age, Single/married/widow, Filipino, And Residing At ________________________________________, Philippines, After Having Been Duly Sworn In Accordance With Law, Do Hereby Depose And State That: 1. I Am The Sole Proprietor Or Authorized Representative Of ______________________________________ With Office Address At ______________________________________; 2. As The Owner And Sole Proprietor, Or Authorized Representative Of _____________________________________, I Have Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For ___________________________________________ [name Of The Project] Of The Iloilo Provincial Government, As Shown In The Attached Duly Notarized Special Power Of Attorney; 3. __________________________________________ Is Not “blacklisted” Or Barred From Bidding By The Government Of The Philippines Or Any Of Its Agencies, Offices, Corporations, Or Local Government Units, Foreign Government/foreign Or International Financing Institution Whose Blacklisting Rules Have Been Recognized By The Government Procurement Policy Board, By Itself Or By Relation, Membership, Association, Affiliation, Or Controlling Interest With Another Blacklisted Person Or Entity As Defined And Provided For In The Uniform Guidelines On Blacklisting; 4. Each Of The Documents Submitted In Satisfaction Of The Bidding Requirements Is An Authentic Copy Of The Original, Complete, And All Statements And Information Provided Therein Are True And Correct; 5. __________________________________________ Is Authorizing The Head Of The Procuring Entity Or Its Duly Authorized Representative(s) To Verify All The Documents Submitted; 6. The Owner Or Sole Proprietor Is Not Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; 7. ___________________________________________ Complies With Existing Labor Laws And Standards; And 8. ___________________________________________ Is Aware Of And Has Undertaken The Responsibilities As A Bidder In Compliance With The Philippine Bidding Documents, Which Includes: A. Carefully Examining All Of The Bidding Documents; B. Acknowledging All Conditions, Local Or Otherwise, Affecting The Implementation Of The Contract; C. Making An Estimate Of The Facilities Available And Needed For The Contract To Be Bid, If Any; And D. Inquiring Or Securing Supplemental/bid Bulletin(s) Issued For The ______________________________________. [name Of The Project] 9. _________________________________________ Did Not Give Or Pay Directly Or Indirectly, Any Commission, Amount, Fee, Or Any Form Of Consideration, Pecuniary Or Otherwise, To Any Person Or Official, Personnel Or Representative Of The Government In Relation To Any Procurement Project Or Activity. 10. In Case Advance Payment Was Made Or Given, Failure To Perform Or Deliver Any Of The Obligations And Undertakings In The Contract Shall Be Sufficient Grounds To Constitute Criminal Liability For Swindling (estafa) Or The Commission Of Fraud With Unfaithfulness Or Abuse Of Confidence Through Misappropriating Or Converting Any Payment Received By A Person Or Entity Under An Obligation Involving The Duty To Deliver Certain Goods Or Services, To The Prejudice Of The Public And The Government Of The Philippines Pursuant To Article 315 Of Act No. 3815 S. 1930, As Amended, Or The Revised Penal Code. In Witness Whereof, I/we Have Hereunto Set My/our Hand/s This ______ __ At ___________________________. ________________________________________________ [signature Over Printed Name Of Bidder Or Its Authorized Representative] [insert Signatory’s Legal Capacity] Subscribed And Sworn To Before Me, _______________________ In The _____________________. Affiant Exhibited To Me His Valid Identification Card With Id No. _________________ Issued By: ___________________. Doc No.:______; Page No. _____; Book No.:_____; Series Of: _____; Republic Of The Philippines) City Of ____________________) S.s. Omnibus Sworn Statement (for A Partnership Or Cooperative) I, _______________________________________of Legal Age, Single/married/widow, Filipino, And Residing At ________________________________________, Philippines, After Having Been Duly Sworn In Accordance With Law, Do Hereby Depose And State That: 1. I Am The Duly Authorized And Designated Representative Of ______________________________ With Office Address At ___________________________________; 2. I Am Granted Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For __________________________________ Of The Iloilo Provincial Government, As Shown [name Of The Project] In The Attached _________________________________________________; [state Title Of Attached Document Showing Proof Of Authorization (e.g., Duly Notarized Secretary’s Certificate, Board/partnership Resolution, Or Special Power Of Attorney, Whichever Is Applicable;] 3. _____________________________________ Is Not “blacklisted” Or Barred From Bidding By The Government Of The Philippines Or Any Of Its Agencies, Offices, Corporations, Or Local Government Units, Foreign Government/foreign Or International Financing Institution Whose Blacklisting Rules Have Been Recognized By The Government Procurement Policy Board, By Itself Or By Relation, Membership, Association, Affiliation, Or Controlling Interest With Another Blacklisted Person Or Entity As Defined And Provided For In The Uniform Guidelines On Blacklisting; 4. Each Of The Documents Submitted In Satisfaction Of The Bidding Requirements Is An Authentic Copy Of The Original, Complete, And All Statements And Information Provided Therein Are True And Correct; 5. _____________________________________ Is Authorizing The Head Of The Procuring Entity Or Its Duly Authorized Representative(s) To Verify All The Documents Submitted; 6. None Of The Officers And Members Of _____________________________________ Is Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; 7. _____________________________________ Complies With Existing Labor Laws And Standards; And 8. _____________________________________ Is Aware Of And Has Undertaken The Responsibilities As A Bidder In Compliance With The Philippine Bidding Documents, Which Includes: A. Carefully Examining All Of The Bidding Documents; B. Acknowledging All Conditions, Local Or Otherwise, Affecting The Implementation Of The Contract; C. Making An Estimate Of The Facilities Available And Needed For The Contract To Be Bid, If Any; And D. Inquiring Or Securing Supplemental/bid Bulletin(s) Issued For The ______________________________________. [name Of The Project] 9. _____________________________________ Did Not Give Or Pay Directly Or Indirectly, Any Commission, Amount, Fee, Or Any Form Of Consideration, Pecuniary Or Otherwise, To Any Person Or Official, Personnel Or Representative Of The Government In Relation To Any Procurement Project Or Activity. 10. In Case Advance Payment Was Made Or Given, Failure To Perform Or Deliver Any Of The Obligations And Undertakings In The Contract Shall Be Sufficient Grounds To Constitute Criminal Liability For Swindling (estafa) Or The Commission Of Fraud With Unfaithfulness Or Abuse Of Confidence Through Misappropriating Or Converting Any Payment Received By A Person Or Entity Under An Obligation Involving The Duty To Deliver Certain Goods Or Services, To The Prejudice Of The Public And The Government Of The Philippines Pursuant To Article 315 Of Act No. 3815 S. 1930, As Amended, Or The Revised Penal Code. In Witness Whereof, I/we Have Hereunto Set My/our Hand/s This ______ __ At ___________________________. _________________________________________________ [signature Over Printed Name Of Bidder Or Its Authorized Representative] [insert Signatory’s Legal Capacity] Subscribed And Sworn To Before Me, _______________________ In The _____________________. Affiant Exhibited To Me His Valid Identification Card With Id No. _________________ Issued By: ___________________. Doc No.:______; Page No. _____; Book No.:_____; Series Of: _____; Republic Of The Philippines) City Of _____________________) S.s. Omnibus Sworn Statement (for A Corporation Or Joint Venture) I, _______________________________________of Legal Age, Single/married/widow, Filipino, And Residing At ________________________________________, Philippines, After Having Been Duly Sworn In Accordance With Law, Do Hereby Depose And State That: 1. I Am The Duly Authorized And Designated Representative Of ______________________________ With Office Address At ___________________________________; 2. I Am Granted Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For __________________________________ Of The Iloilo Provincial Government, As Shown [name Of The Project] In The Attached _________________________________________________; [state Title Of Attached Document Showing Proof Of Authorization (e.g., Duly Notarized Secretary’s Certificate, Board/partnership Resolution, Or Special Power Of Attorney, Whichever Is Applicable;] 3. _____________________________________ Is Not “blacklisted” Or Barred From Bidding By The Government Of The Philippines Or Any Of Its Agencies, Offices, Corporations, Or Local Government Units, Foreign Government/foreign Or International Financing Institution Whose Blacklisting Rules Have Been Recognized By The Government Procurement Policy Board, By Itself Or By Relation, Membership, Association, Affiliation, Or Controlling Interest With Another Blacklisted Person Or Entity As Defined And Provided For In The Uniform Guidelines On Blacklisting; 4. Each Of The Documents Submitted In Satisfaction Of The Bidding Requirements Is An Authentic Copy Of The Original, Complete, And All Statements And Information Provided Therein Are True And Correct; 5. _____________________________________ Is Authorizing The Head Of The Procuring Entity Or Its Duly Authorized Representative(s) To Verify All The Documents Submitted; 6. None Of The Officers, Directors, And Controlling Stockholders Of _____________________________________is Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; 7. _____________________________________ Complies With Existing Labor Laws And Standards; And 8. _____________________________________ Is Aware Of And Has Undertaken The Responsibilities As A Bidder In Compliance With The Philippine Bidding Documents, Which Includes: E. Carefully Examining All Of The Bidding Documents; F. Acknowledging All Conditions, Local Or Otherwise, Affecting The Implementation Of The Contract; G. Making An Estimate Of The Facilities Available And Needed For The Contract To Be Bid, If Any; And H. Inquiring Or Securing Supplemental/bid Bulletin(s) Issued For The ______________________________________. [name Of The Project] 9. _____________________________________ Did Not Give Or Pay Directly Or Indirectly, Any Commission, Amount, Fee, Or Any Form Of Consideration, Pecuniary Or Otherwise, To Any Person Or Official, Personnel Or Representative Of The Government In Relation To Any Procurement Project Or Activity. 10. In Case Advance Payment Was Made Or Given, Failure To Perform Or Deliver Any Of The Obligations And Undertakings In The Contract Shall Be Sufficient Grounds To Constitute Criminal Liability For Swindling (estafa) Or The Commission Of Fraud With Unfaithfulness Or Abuse Of Confidence Through Misappropriating Or Converting Any Payment Received By A Person Or Entity Under An Obligation Involving The Duty To Deliver Certain Goods Or Services, To The Prejudice Of The Public And The Government Of The Philippines Pursuant To Article 315 Of Act No. 3815 S. 1930, As Amended, Or The Revised Penal Code. In Witness Whereof, I/we Have Hereunto Set My/our Hand/s This ______ __ At ___________________________. ________________________________________________ [signature Over Printed Name Of Bidder Or Its Authorized Representative] [insert Signatory’s Legal Capacity] Subscribed And Sworn To Before Me, _______________________ In The _____________________. Affiant Exhibited To Me His Valid Identification Card With Id No. _________________ Issued By: ___________________. Doc No.:______; Page No. _____; Book No.:_____; Series Of: _____; Republic Of The Philippines) City Of ____________________) S.s. Performance Securing Declaration Bid No: ____________________ To: Bids And Awards Committee Iloilo Provincial Government Iloilo Provincial Capitol Bonifacio Drive, Iloilo City I/we, The Undersigned, Declare That: 1. I/we Understand That, According To Your Conditions, To Guarantee The Faithful Performance By The Supplier/distributor/manufacturer/contractor/consultant Of Its Obligations Under The Contract, I/we Shall Submit A Performance Securing Declaration Within A Maximum Period Of Ten (10) Calendar Days From The Receipt Of The Notice Of Award Prior To The Signing Of The Contract. 2. I/we Accept That: I/we Will Be Automatically Disqualified From Bidding For Any Procurement Contract With Any Procuring Entity For A Period Of One (1) Year For The First Offense, Or Two (2) Years For The Second Offense, Upon Receipt Of Your Blacklisting Order If I/we Have Violated My/our Obligations Under The Contract; 3. I/we Understand That This Performance Securing Declaration Shall Cease To Be Valid Upon: A. Issuance By The Procuring Entity Of The Certificate Of Final Acceptance, Subject To The Following Conditions: I. Procuring Entity Has No Claims Filed Against The Contract Awardee; Ii. It Has No Claims For Labor And Materials Filed Against The Contractor; And Iii. Other Terms Of The Contract; Or B. Replacement By The Winning Bidder Of The Submitted Psd With A Performance Security In Any Of The Prescribed Forms Under Section 39.2 Of The 2016 Revised Irr Of Ra No. 9184 As Required By The End-user. In Witness Whereof, I/we Have Hereunto Set My/our Hand/s This ______ __ At ___________________________. _________________________________________________ [signature Over Printed Name Of Bidder Or Its Authorized Representative] [insert Signatory’s Legal Capacity] Subscribed And Sworn To Before Me, _______________________ In The _____________________. Affiant Exhibited To Me His Valid Identification Card With Id No. _________________ Issued By: ___________________. Doc No.:______; Page No. _____; Book No.:_____; Series Of: _____; Email Address: ______________________________________ Statement Of Single Largest Completed Contract (slcc) Similar To The Contract To Be Bid Bidder’s Name: Email Address: Bidder’s Address: Fax Number: Tel. Number: Name Of Project Amount Of Contract Date Of Contract Effectivity Owner’s Name And Address Delivery Period Date Of Delivery Date Of Acceptance Signature Over Printed Name Attachments: 1. Purchase Order (po) 2. Acceptance And Inspection Report (air) Statement Of All On-going Government And Private Contracts (including Contracts Awarded But Not Yet Started, If Any, Whether Similar Or Not Similar In Nature And Complexity To The Contract To Be Bid) Bidder’s Name: Email Address: Bidder’s Address: Fax Number: Tel. Number: Name Of Project/s Amount Of Contract Date Of Contract Effectivity Owner’s Names And Address Delivery Period (indicate All Delivery Periods If Staggered Delivery Allowed) End Of Delivery Period Value Of Outstanding Contracts (indicate If Partial Delivery Allowed) No. Of Days From End Of Delivery Period Days Of Approved Extension/ Suspension, If Any Total Value Of Outstanding Contracts (php) Signature Over Printed Name Fill Up All The Columns Accordingly Disclaimer: Non-disclosure Of All On-going Contracts And Details Thereof Is Grounds For Ineligibility And Disqualification.
Closing Soon25 Nov 2024
Tender AmountPHP 747.1 K (USD 12.6 K)
Oriental Mindoro Tender
Electronics Equipment...+2Electrical and Electronics, Solar Installation and Products
Philippines
Details: Description Invitation To Bid Purchase Of Office Supplies And Devices For Use Of Pgom Office Supplies And Devices/other Supplies (4th Quarter) Based On Consolidated Annual Procurement Plan For The Year 2024 Ib No. Gsa 2024-11-076 1. The Provincial Government Of Oriental Mindoro, Through The General Fund Intends To Apply The Sum Of One Million Four Hundred Forty Two Thousand Seven Hundred Twenty Three Pesos And 25/100 Only (php 1,442,723.25) Being The Abc To Payments Under The Contract For Purchase Of Office Supplies And Devices For Use Of Pgom Office Supplies And Devices/other Supplies (4th Quarter) Based On Consolidated Annual Procurement Plan For The Year 2024. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. 2. The Provincial Government Of Oriental Mindoro – Procurement Division Now Invites Bids For The Above Procurement Project. Delivery Of The Goods Is Required Within Seven (7) Calendar Days Upon Signing Of The Notice To Proceed. Bidders Should Have Completed, Within Two (2) Years From The Date Of Submission And Receipt Of Bids, A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii (instructions To Bidders). Item No. Item Description Qty./unit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 Office Supplies Ballpen Bps Fine (84 Black) Ballpen 0.5 Mm (292 Black, 200 Blue) Ballpen 1.0 (95 Black) Ballpen G2 .07 (150 Blue,120 Black) Ballpen I-gel Retractable (90 Black, 6 Pink,6 Blue, 6 Red,6 Green, 51 Asst.) Ballpen (gel Pen) (15 Black, 20 Blue) Ballpen G .5 (100 Green) Ballpen, Ordinary (12 Black) Ballpen, Retractable (1,209 Black,90 Blue,15 Red, 19 Asst. Color) Bond Paper A3 5-20 70 Gsm Bond Paper A4 70 Gsm Bond Paper A4 80 Gsm Bond Paper A4 100 Gsm Bond Paper Long S-20 70gsm Bond Paper Short S-20 70gsm Bond Paper Long 80 Gsm Subs. 20 Bond Paper Short 80 Gsm Subs. 20 Bond Paper Long Colored Cambric Board Long (25 White, Yellow, 30 Beige, 2 Cream) Cambric Paper Long (2 White Cream, 6 Beige) Cambric Board Short (30 Beige,6 Green, 15 White) Cambric Paper Short (3 White Cream, 8 Beige) Calculator Aoc 12 Digits Black Calculator Mx12b Calculator Ribbon (dr120) Carbon Paper, Long Clip Binder, 2" Clip Binder, 1" Clip Binder, ¾ Clip Binder, Small Colored Paper Asstd. Color L, Pastel Color Colored Paper Long (green) Combo Cover Plastic (long) Combo Cover Plastic (a4) Combo Cover Plastic (short) Combo Ring 1/2" Combo Ring 1/4" Combo Ring 3/4" Combo Ring 1" Combo Ring 1 1/4 Combo Ring 1/1/2 Combo Ring 2" Columnar Notebooks 12 Columns Specialty Paper (long) Yellow Correction Pen Correction Tape Correction Fluid Cutter Big Heavy Duty Cutter Blade, Big Double Sided Tape, 1" Hd Double Sided Tape, 1" Double Sided Tape, .5 Duct Tape 2" Thick Duct Tape 2" Thick Hd Duct Tape 3" Thick Engineer's Field Book Envelope Brown Long Envelope Brown Short Expanded Envelope With Garter - Long (207 Green,10 Yellow, 50 Blue) Expanded Plastic Envelope Long Thick W/ Handle Expanding Envelope Long Expanding Folder Long (thick) (117 Green) Expanding Folder Short Eraser, Big Eraser, Medium Fastener, Plastic Fastener Plastic 6 Inches Fastener Plastic 8 Inches File Box Single File Box Double File Rack Double Folder White Long (rms) Folder White Long Folder White Short Folder Short Folder Ordinary - Long Folder Press Board Long (1,270 Green,75 Red) Glue - 130gms Glue Padding 500g Glue Stick, Big High Lighter Pen,(asstd., Green, Yellow) Illustration Board (1/4) Illustration Board (1/8) Ink Refill 003 65ml 00v1 For Epson (magenta) Ink Refill 003 65ml 00v1 For Epson (cyan) Ink Refill 003 65ml 00v1 For Epson (yellow) Ink 001 L6170 Black For Epson Ink 001 L6170 Cyan For Epson Ink 001 L6170 Magenta For Epson Ink 001 L6170 Yellow For Epson Ink #810 Black For Canon Printer Ink #811 Colored For Canon Printer Ink #704 Black For Hp Printer Ink #704 Tri Color For Hp Printer Ink Ts207#745xl For Canon Printer Black Cartridge Ink Ts207#746xl For Canon Printer Colored Cartridge Ink Refill Bt D60 Bk 108ml Ink Refill Bt 5000m For Brother Printer Ink Refill Bt 5000c For Brother Printer Ink Refill Bt 5000y For Brother Printer Ink L3110 Black Ink L3110 Cyan Ink L3110 Yellow Ink L3110 Magenta Ink 003 Black For Epson Printer Ink 003 Yellow For Epson Printer Ink 003 Magenta For Epson Printer Ink 003 Cyan For Epson Printer Ink Lc535xl For Brother Printer Black Ink - T 6641 Refill - Black Ink - T 6643 Refill - Magenta Ink - T 6642 Refill - Cyan Ink - T 6644 Refill - Yellow Ink Universal - Set Ink Universal - Black Ink Universal - Cyan Ink Universal - Magenta Ink Universal - Yellow Ink Universal - Black 100ml Ink Universal - Yellow 100ml Ink Universal - Magenta 100ml Ink Universal - Cyan 100ml Indexing Tab, Plastic Indexing Tab Multicolor Plastic 7's Intermediate Pad Paper Laminating Film A4 Laminating Film Long 1.25 Laminating Film Short 1.25 Mailing Envelop White Long Adv. Masking Tape, 1" Masking Tape, 2" Mechanical Pencil Lead (.05) Mechanical Pencil Lead (.07) Notebook, Thick With Yarn Notebook, Writing Pad Paper, Assorted Color Packaging Tape Packaging Tape 3" Paper Clip - Small Paper Clip -big Paste 170 Gms Pencil #2 Pencil Sharpener Pentelpen - Fine (black, Blue) Pentelpen - Broad (black, Blue) Pentelpen - Ink (black) Photo Paper (3 Inkjet, 34 Glossy) Post It Flags Asst Primary Colors, 100 Flags Post It Tape Flag #683-4 1inchx1.17inch 11,9mm Post It Note 5x2, Green, Blue Post It Note 1x3 Green, Asst. Post It Note 2x3 (green, Pink, Yellow, Light Blue) Post It Note 3x3 Post It Note 3x4 (green, Light Blue, Mint Green, Pink) Post It Note 5x3 Post It Note 4x4 Poster Color 12's Portable Hard Drive 1tb Puncher - Heavy Duty Push Pin 50s Record Book 500pg Record Book 300pg (18 Green, Blue, Red, 2 Asstd.) Record Book 200pg Green, Blue, Red Report Clear Folder Long Report Clear Folder Short Ruler, Plastic 12" Ruler, Metal, 12" Scissors, Hd Scotch Tape 1 Inch Scotch Tape 2" Sticky Notes Signpen 0.7 V Ball (23 Blue, 4 Black, 6 Violet) Signpen - Gel Impact, 1.0,(4 Blue, 7 Black) Signpen - Gel Impact, 1.0 (black) Signpen, Gel (black, Blue, Red) Signpen, Hi-tech V-ball .5 (47 Black,12 Blue,6 Green) Signpen, Hi-tech V-ball .7 (6 Black,16 Blue) Signpen,v.5 (violet, Blue, Black, Green) Sliding Folder Long Plastic Hard Board Green Stamp Pad Ink 946ml Blue Stamp Pad, Big Stamp Pad Ink Big 473ml (violet, Blue) Staple Wire#35 Stapler With Remover, #35 Hd Steno Notebook (30pp) Sticker Paper Sticker Paper Matte, Glossy Tabbing Clear 1/2 Tacker Tacker Wire Tape Dispenser Big Thermal Binding Cover A4 4mm Thumbtacks Toner Mp2000l2 Dsm 615 Toner Mp 2501sp Ups 1000va Vellum Board Short 220gsm (white) Vellum Board Short 100 Shts 200 Gms (2 Green, 6 White, 10 Pink) White Board Marker (35 Black, 8 Blue,7 Red) White Board Eraser Yellow Pad Other Supplies Airfreshner 227 G Airfreshner In Canister 320ml (lemon Scent) Airfreshner Scented Gel 180g Airfreshner Spray 320ml (asstd. Scent, Sampaguita, Lemon, Lavender, Fresh & Light) Airfreshner Spray 120ml Blossom & Breeze Alcohol Gal Alcohol 70% Isoprophyl 250ml Alcohol 70% Isoprophyl 500ml Airfreshener 320ml (light Blue, Light Pink, Yellow & White) Bath Soap Small Sachet Blank Cd-r Bleaching Liquid Bleaching Liquid (white) Basahang Bilog Thick Box Tissue Bath Soap (family Size) Bath Soap Regular Battery Aaa Hd Battery Aa Hd Battery Aaa Hd Battery Aa Hd Battery Aa Black Battery Aaa Black Bulb 18watts Bulb Socket Baby Powder 25g Bra (s,32,34,36) Bracket, S-3/4 Bed Sheet Cover, Single (3 In 1) Burner, Gas, Hd Ic40 Computer Keyboard Computer Mouse Wireless Computer Mouse Pad Cd Recordable Car Shampoo Chamois Cabinet Plastic Organizer Cotton 50gms Cotton 100gms Cotton Buds 300/cn Cable Tie Medium Cable Tie Large Deodorant Cake Deodorant Cake W/ Case Deodorant Roll On Detergent Bar Dishwashing Liquid 250ml Dishwashing Liquid 600ml Dishwashing Paste Big Disinfectant All Purpose Cleaner Big Disinfectant Spray 720g Disinfectant Spray 720g Disinfectant Spray 340g Disinfectant Spray 275g Disposable Mask (black, Green) Door Knob (hd) Door Mat Rug Thick Dust Pan Stainless L6270 Maintenance Box (to4d1) Escuba Brush Extension Wire (hd 4 Sockets 10mtrs) Fabric Conditioner Sachet Fabric Conditioner Antibac Ltr Faucet Copper Flash Drive 8gb Flash Drive 16gb Flash Drive 32gb Flash Drive 64gb Fluorescent Tube 16watts Fluorescent Bulb Led 36 Watts, Day Light Fork Floor Brush With Long Handle Flower Pot Xl Furniture Cleaner Furniture Polish Spray 330ml Garbage Bag 14x14 (green) Garbage Bag Biodegradable 36x48 Garbage Bag Medium Biodegradable Garbage Bag Large Size (black) Garbage Bag Large Size Garbage Bag Extra Large Thick Garbage Bag Small Garbage Bag Big (6 Black, 6 Yellow, 6 Green) 100's Garbage Bag 11x14x100's (11x11x24) Garbage Bag Small 9x9x20 100's Garbage Bag Small Plastic Garbage Bag 16x24x100's Garbage Bag 18.5x18.5x40 Glass Cleaner Big Spray 500ml Glass Clear, Big (lg-33) Glass, Small Hanger Hanger With Clip Hand Sanitizer 500ml Hand Towel Hand Towel, Micro Fiber Hand Wash Liquid 250 Ml Insecticide Spray Big (12 Water Base) 500ml Kitchen Faucet Stainless Keyboard Cleaning Brush Led Bulb 12 Watts Led Bulb 15 Watts Led Bulb 16 Watts Led Bulb 18 Watts Memory Card 128gb Extreme Pro (170mb/s) Monopod/tripod 2in1 Mop Handle Plastic Hd Mop Head #40 Cloth Mop Head Cloth Hd Paper Cups 100's Paper Towel Big Paper Towel Big Interfolded Pail W/ Cover Big Plastic Garbage 13x13x32 (100's) Powder Detergent 1kl Powder Laundry Sachet Powder Laundry 500g Pranela Rag (10pc/pack) Panty (s,m,l) Rechargeable Flash Light Heavy Duty Scouring Pad W/ Foam Big Scouring Pad W/ Foam Small Scouring Pad Sando Bag Plastic Medium Biodegradable Shoe Lace Steel Whool Sando Bag Large Biodegradable 100's Shampoo Slipper Spoon Sponge Sanitary Napkins Solar Light, Outdoor 800watts Tawas Powder 50g Tissue Paper 2 Ply Tissue Paper 3 Ply Tissue Paper 3 Ply (set Of 12) Thermal Paper Toilet Bowl Brush Toilet Bowl Brush Plastic Handle Toilet Bowl Brush With Long Handle Toilet Deodorizer Strawberry (a) Toilet Bowl Cleaner 1l Toilet Bowl Cleaner 500ml Toilet Bowl Cleaner 1l Trash Can Big Toothpaste Triple Action (2x 195g) Tornado Mop Big Hd Tornado Mop Head Usb 3.0 Otg Card Reader Utility Flexi Box Large Plastic Utility Gloves Water Based Essential Oil For Humidifier 100ml Walis Tamboo Thick Walis Tinting Irok X-x-x-x 84 Pcs 492 Pcs 95 Pcs 20 Pcs 165 Pcs 35 Pcs 100 Pcs 12 Pcs 1,333 Pcs 40 Rms 16 Rms 12 Rms 2 Rms 875 Rms 486 Rms 3 Rms 3 Rms 5 Rms 42 Packs 8 Packs 36 Packs 11 Packs 4 Pcs 6 Pcs 10 Bxs 1 Bx 13 Boxes 29 Boxes 28 Boxes 6 Boxes 2 Rms 1 Rm 81 Pcs 25 Pcs 31 Pcs 20 Pcs 18 Pcs 16 Pcs 23 Pcs 16 Pcs 10 Pcs 10 Pcs 2 Pcs 1 Rm 29 Pcs 210 Pcs 6 Pcs 12 Pcs 2 Tubes 1 Pc 67 Rolls 7 Rolls 6 Rolls 2 Rolls 6 Rolls 10 Pcs 260 Pcs 125 Pcs 267 Pcs 10 Pcs 10 Pcs 117 Pcs 12 Pcs 6 Pcs 6 Pcs 95 Boxes 2 Boxes 1 Box 13 Pcs 13 Pcs 1 Pc 1 Rm 87 Pcs 39 Pcs 266 Pcs 855 Pcs 1,345 Pcs 43 Pcs 2 Jar 10 Pcs 125 Pcs 3 Pcs 3 Pcs 1 Pc 1 Pc 1 Pc 2 Pcs 2 Pcs 2 Pcs 2 Pcs 5 Boxes 2 Boxes 3 Cart 3 Cart 3 Pcs 3 Pcs 5 Boxes 5 Boxes 5 Boxes 5 Boxes 40 Cart 16 Cart 16 Cart 16 Cart 10 Pcs 3 Pcs 3 Pcs 5 Pcs 1 Crtg 21 Crtg 10 Crtg 10 Bxs 10 Bxs 5 Set 6 Ltr 2 Ltr 2 Ltr 2 Ltr 12 Btls 8 Btls 8 Bts 8 Btls 16 Packs 6 Packs 5 Pads 50 Pcs 25 Pcs 9 Pcs 3 Boxes 33 Rolls 32 Rolls 2 Pcs 3 Pcs 25 Pcs 15 Pcs 1 Pad 10 Rolls 14 Rolls 47 Boxes 27 Boxes 3 Btls 91 Pcs 1 Pcs 68 Pcs 17 Pcs 4 Btls 12 Packs 2 Packs 12 Packs 7 Pads 18 Pads 10 Pads 10 Pads 9 Pads 2 Pads 2 Pads 1 Box 2 Pcs 6 Pcs 5 Boxes 10 Pcs 28 Pcs 11 Pcs 19 Pcs 10 Pcs 7 Pcs 4pcs 4 Pcs 211 Rolls 9 Rolls 10 Packs 33 Pcs 11 Boxes 15 Pcs 22 Pcs 65 Pcs 22 Pcs 11 Pcs 19 Pcs 2 Pcs 3 Pcs 5 Btls 101 Boxes 6 Pcs 10 Pcs 5 Pcs 4 Packs 8 Packs 1 Pcs 1 Box 4 Pcs 6 Pcs 6 Boxes 1 Pcs 1 Pcs 1 Unit 10 Packs 18 Rms 50 Pcs 2 Pcs 5 Pads 4 Tins 10 Pcs 2 Pcs 39 Tins 30 Tins 20 Gal 3 Btls 220 Btls 22 Tins 20 Pcs 5 Pcs 13 Gals 41 Ltrs 115 Pcs 16 Bxs 169 Pcs 27 Pcs 18 Pair 39 Pair 5 Pcs 10 Pcs 9 Pair 10 Pair 4 Pcs 4 Pcs 25 Pcs 30 Pcs 3 Pcs 7 Pcs 1 Pcs 1 Pcs 4 Pcs 3 Pcs 4 Pcs 1 Gals 11 Packs 3 Pc 4 Pcs 5 Pcs 30 Cons 1 Packs 5 Pack 246 Pcs 10 Pcs 30 Pcs 282 Bar 357 Btls 3 Btls 33 Jar 15 Btls 1 Tins 5 Tins 19 Tins 26 Tins 2 Bxs 2 Pcs 92 Pcs 7 Pcs 1 Pcs 2 Pcs 2 Rolls 438 Scht 13 Ltrs 3 Pcs 4 Pcs 2 Pcs 3 Pcs 4 Pcs 2 Pcs 9 Pcs 1 Doz 3 Pcs 4 Pcs 1 Tin 44 Pcs 5 Pack 238 Pcs 821 Pcs 1149 Pcs 5 Rolls 400 Pcs 150 Pcs 18 Bndls 2 Pack 6 Pack 1 Bndl 1 Pack 1 Bndl 54 Btls 8 Pcs 8 Pcs 14 Doz 23 Doz 11 Btls 54 Pcs 8 Pcs 86 Pcs 75 Tins 2 Set 3 Pcs 10 Pcs 12 Pcs 11 Pcs 19 Pcs 2 Pcs 1 Pcs 4 Pcs 1 Pcs 14 Pcs 1 Bndls 3 Rolls 33 Packs 4 Pcs 5 Packs 33 Packs 1632 Scht 24 Packs 16 Packs 9 Doz 3 Set 26 Pcs 77 Pcs 30 Pcs 6 Packs 9 Rolls 52 Pcs 10 Packs 125 Dozen 50 Pairs 3 Dozen 58 Pcs 150 Packs 1 Pcs 50 Pcs 81 Rlls 910 Rlls 106 Packs 15 Rlls 5 Pcs 1 Pcs 4 Pcs 16 Ltrs 15 Ltrs 51 Btls 14 Ltrs 2 Pcs 37 Pcs 4 Pcs 1 Pcs 1 Pc 6 Pcs 33 Pcs 3 Btls 28 Pcs 9 Pcs 3. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using A Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) No. 9184. Bidding Is Restricted To Filipino Citizens/sole Proprietorships, Partnerships, Or Organizations With At Least Sixty Percent (60%) Interest Or Outstanding Capital Stock Belonging To Citizens Of The Philippines, And To Citizens Or Organizations Of A Country The Laws Or Regulations Of Which Grant Similar Rights Or Privileges To Filipino Citizens, Pursuant To Ra No. 5183. Activities Schedule Advertisement/posting Of Ib November 7, 2024 Bulletin Board Of The Pgom November 7, 2024 Pgom Website – Www.ormindoro.gov.ph November 7, 2024 Geps Website – Www.philgeps.net November 7, 2024 Issuance Of Bidding Documents November 7, 2024 To November 26, 2024 Pre-bid Conference November 14, 2024 At 10:00 Am Ppeso Conference Room Deadline Of Submission Of Bids November 26, 2024 At 9:30 Am At Procurement Division Opening Of Bids In Sealed Envelope November 26, 2024 At 10:00 Am At Ppeso Conference Room A) Eligibility Requirements And Technical Proposal November 26, 2024 At 10:00 Am At Ppeso Conference Room B) Financial Proposal November 26, 2024 At 10:00 Am At Ppeso Conference Room 4. Prospective Bidders May Obtain Further Information From Provincial Government Of Oriental Mindoro-procurement Division And Inspect The Bidding Documents At The Address Given Below During 8:00 Am To 5:00 Pm. 5. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders On November 7, 2024 To November 26, 2024 From The Given Address And Website(s) Below And Upon Payment Of The Applicable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb, In The Amount Of Five Thousand Pesos Only (php 5,000.00). The Procuring Entity Shall Allow The Bidder To Present Its Proof Of Payment For The Fees In Person. 6. The Provincial Government Of Oriental Mindoro-procurement Division Will Hold A Pre-bid Conference On November 14, 2024 At 10:00 Am At Ppeso Conference Room, Provincial Capitol Complex, Camilmil Calapan City, Oriental Mindoro Which Shall Be Open To Prospective Bidders. 7. Bids Must Be Duly Received By The Bac Secretariat Through Manual Submission At The Procurement Division, On Or Before November 26, 2024 At 9:30 Am. Late Bids Shall Not Be Accepted. 8. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 14. 9. Bid Opening Shall Be On November 26, 2024 At 10:00 Am At Ppeso Conference Room, Provincial Capitol Complex, Camilmil Calapan City Oriental Mindoro. Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend The Activity. 10. The Pgom – Procurement Division Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Irr Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 11. For Further Information, Please Refer To: Marissa O. Acuzar Procurement Division – Goods And Services Provincial Capitol Complex Camilmil, Calapan City Oriental Mindoro 5200 Antonio M. Magnaye, Jr. Bac Chairperson
Closing Soon26 Nov 2024
Tender AmountPHP 1.4 Million (USD 24.4 K)
City Of Canlaon Tender
Civil And Construction...+1Construction Material
Philippines
Details: Description Republic Of The Philippines City Of Canlaon Office Of The Bids And Awards Committee Invitation To Bid For The Early Procurement Activity (epa) For The Procurement Of Construction Materials For The Improvement Of Day Care Center, Phase 2 The Local Government Of Canlaon City, Through The Aip 2025 Intends To Apply The Sum Five Hundred Eighty-three Thousand, Eight Hundred Forty-five & 72/100 (p583,845.72) Being The Abc To Payments Under The Contract For The Supply And Delivery Of Various Construction Materials For Use In The Improvement Of Day Care Center, Phase 2, Brgy. Lumapao, Canlaon City. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. The Award Of The Contract Is Subject To The Effectivity Of The General Appropriations Act (gaa) For Fy 2025. The Local Government Of Canlaon City Is Conducting This Procurement Through The Early Procurement Activity (epa) For Fy 2025 To Ensure The Timely Delivery Of Goods, Implementation Of Infrastructure Projects And Rendition Of Consultancy Services, Consistent With The Gppb Resolution No. 14-2019 Dated July 17, 2019. Epa Shall Refer To The Conduct Of Procurement Activities, From Posting Of The Procurement Opportunity, If Required, Until Recommendation Of The Bids And Awards Committee (bac) To The Hope As To The Award Of The Contract For Goods To Be Delivered, Infrastructure Projects To Be Implemented And Consulting Services To Be Rendered In The Following Fiscal Year (i.e Fy 2025), Pending Approval Of Their Respective Funding Sources. The Bidders, Therefore, Are Herewith Informed Of The Following: A. Interested Bidders Are Invited/requested To Submit Their Bid Proposals Based On Indicative Budget (i.e. Subject To Final Approval) Through This Invitation To Bid, Together With The Bidding Documents; B. The Local Government Of Canlaon City, Will Evaluate The Bid Proposal And Determine The Winning Bidder. The Financial Bid Proposal Of The Winning Bidder Will Be The Contract Price/amount Which Is Considered Fixed Price. However, The Notice Of Award (noa) Will Only Be Issued Upon The Approval Of The Budget. C. Would There Be A Delay In The Award As Affected By The Possible Delay In The Budget Approval, The Bid Validity As Specified In The Bidding Documents (which Is A Maximum Of 120 Calendar Days), The Winning Bidder May Be Requested To Extend The Validity, If The Bidder Refuses To Extend The Bid Validity, The Bid Submitted By Said Bidder Will Be Rejected. The Local Government Of Canlaon City, Now Invites Bids For The Supply And Delivery Of Various Construction Materials For Use In The Improvement Of Day Care Center, Phase 2, Brgy. Lumapao, Canlaon City. Delivery Of The Goods Is Required 7 Calendar Days After Issuance And Receipt Of Notice To Proceed. Bidders Should Have Completed, Within Ten Years From The Date Of Submission And Receipt Of Bids, A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii (instructions To Bidders). Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using A Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) No. 9184. Bidding Is Open To All Interested Bidders, Whether Local Or Foreign, Subject To The Conditions For Eligibility Provided In The 2016 Revised Irr Of Ra No. 9184 Interested Bidders May Obtain Information For The City Government Of Canlaon City Thru The Office Of The Bids And Awards Committee And Inspect Bidding Documents During Office Hours (8:00am To 5:00pm), Monday To Friday. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders Starting On November 5, 2024 To November 25, 2024 Until 10:00 Am At The Office Of The Bids And Awards Committee, Canlaon City, And Upon Payment Of The Applicable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb, In The Amount Of One Thousand (p1,000.00) Pesos. The Procuring Entity Shall Allow The Bidder To Present Its Proof Of Payment For The Fees By Facsimile. The Local Government Of Canlaon City Will Hold A Pre-bid Conference On November 12, 2024 – 2:00 Pm At The Office Of The Bids And Awards Committee 2nd Floor, City Hall Building, Canlaon City, Which Shall Be Open To Prospective Bidders Bids Must Be Received By The Bac Secretariat Through Manual Submission On Or Before November 25, 2024, 10:00 Am At The Office Of The Bids And Awards Committee, 2nd Floor, City Hall Building, Canlaon City. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 14. Bid Opening Shall Be On November 25, 2024, 10:00 Am At The At The Office Of The Bids And Awards Committee 2nd Floor, City Hall Building, Canlaon City. Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend The Activity. For The Purpose Of Constituting A Quorum, Either The Physical And Virtual Presence Of The Bac Member Shall Be Considered Pursuant To Gppb Resolution No. 09-2020. The Local Government Unit Of Canlaon Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Irr Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. For Further Information, Please Refer To: Alice D. Mcguiggan Bac Secretariat Mobile No. 0917-561-7931 Email Address: Bacofficelgucanlaon@yahoo.com Date Of Posting: November 4, 2024 Doris Y. Flores Bac Chairperson Republic Of The Philippines City Of Canlaon Bids And Awards Committee Control No.: #1 Bid Form Name Of Project: Improvement Of Day Care Center, Phase 2 Brief Description: Supply And Delivery Of Various Construction Materials Location: Brgy. Lumapao, Canlaon City Bill Of Quantities Stock No. Quantity Unit Item Description Unit Cost Unit Cost Total Cost 1. 276 L.m. 92 Sheets - Dn Rib 25, Straight Panel (10' X 1092mm) 495.00 2. 14 Box Blind Rivets, (5/32" X 3/4") 546.00 3. 2 Pc Bolt, 1/2"ɸ X 6", B.i., Full Thread With Nut And Washer 85.00 4. 200 Pcs Cable Ties, 8 X 300 Mm 12.00 5. 34 Length Carrying Channel (11mm X 37mm X 11mm X 1.6mm X 5m) 279.00 6. 2 Pc Caulking Gun 313.00 7. 1 Pc Ceiling Vent W/ Insect Screen (300mm X 300mm) 587.50 8. 1 Gal Concrete Epoxy, High Viscosity (a & B) 4,586.25 9. 40 Mtrs. Conductor Wire, 14.0mm² Thw, Cu. 132.50 10. 350 Mtrs. Conductor Wire, 3.5mm² Tw, Cu. 52.00 11. 15 Mtrs. Conductor Wire, 8.0 Mm² Tw, For Grounding 113.00 12. 10 Pcs Conduit Clamp, 25mm ɸ Upvc, Orange Color W/ Concrete Nail 5.25 13. 1 Lngth Conduit Pipe, 25mm ɸ X 3m', Rsc 337.50 14. 1 Pc Connector Ground Rod For ⅝"ɸ, Galv. 102.00 15. 5 Pcs Connector, Compression, Parallel #100 150.00 16. 8 Sets Convenience Outlet, Duplex, Universal, Flush Type, Equivalent 197.00 17. 70 Length Double Furring (17mm X 49mm X 17mm X 0.6mm X 5m) 217.00 18. 8 Set Drill Bit, (5/32" Ø), For Steel 128.33 19. 3 Sets Duplex Switch, Flush Type, Anam Or Equivalent 350.00 20. 3 Rolls Electrical Tape, (0.16mm X 19mm X 16yrds), Plastic 75.00 21. 1 Pc Entrance Cap, 25mm ɸ, Rsc 162.00 22. 20 Gal Epoxy Primer Red Oxide W/ Catalyst 1,358.00 23. 21 Length Fascia Cover, (16" X 8') 500.00 24. 21 Length Fascia End-flashing, (24" X 8') 500.00 25. 16 Gal Flat Latex White 931.50 26. 200 Mtrs. Flexible Conduit Pipe, 20mm ɸ Upvc, Coilable, Orange Color 78.75 27. 10 Mtrs. Flexible Conduit Pipe, 25mm ɸ Upvc, Orange Color, Coilable 113.00 28. 2 Lngth Gi Pipe 3"ɸx20' Sched. 40 4,231.50 29. 1 Lngth Ground Rod, ⅝" ɸ X 10' , Galv. Steel 933.00 30. 49 Sheet Hardiflex (1/4" X 4' X 8') 907.67 31. 16 Length Hip Roll, (16" X 8') 500.00 32. 16 Pcs. Junction Box, 4" X 4" Upvc, Orange Color W/ Cover And Screws 54.00 33. 9 Pcs Led Bulb (9w) 120.00 34. 7 Roll Mesh Tape 116.00 35. 20 Pc Paint Brush, 2" 52.00 36. 20 Pc Paint Brush, 3" 98.50 37. 9 Pc Paint Tray/roller Pan 114.00 38. 1 Assy. Panel Board, 40at/50af, Bolt-on, 240 V, Complete With 2-15at And 2-20at 2-pole, 240v, Bolt-on Branch Circiuts 8,000.00 39. 229 Pcs Paper White Madera Glazed (600mm X 600mm) 182.50 40. 50 Pcs Poly Flex Connector For Flexible Hose 20mm' ɸ 12.00 41. 1 Pc. Pull Box, 12" X 12" X 6" Depth, Melamine Coated W/ Cover 1,100.00 42. 4 Pcs Pvc Air Vent (0.6m X 1.2m) 800.00 43. 2 Length Ridge Roll, (16" X 8') 500.00 44. 20 Pc Roller Brush, 9" 95.00 45. 9 Pcs Round Vertical Downlight Recessed Type, Glossy Reflector, 6" 180.00 46. 8 Gal Rust Converter 948.00 47. 40 Ft2 Sand Paper #120 38.00 48. 20 Ft2 Sand Paper #80 132.50 49. 157 Pcs Sandy White Ceramic Red Body (300mm X 300mm) 42.50 50. 2 Set Secondary Rack With Sool Insulator 1-3/4" Dia, Groove, Brown Porcelain Hd 400.00 51. 20 Gal Semi-gloss Latex 1,067.00 52. 150 Mtrs. Service Drop Wire, 14.0mm², Duplex, All Aluminum 41.00 53. 10 Tube Silicone Sealant 313.00 54. 2 Sets Single Pole Switch, Flush Type, Or Equivalent 148.00 55. 75 Bags Skim Coat, 25kgs 709.50 56. 2 Pc Standard Wall Fan- Metal Type, 18'' (sof-18t2) 2,500.00 57. 2,080 Pc Tekscrew, (5/16" X 2 1/2") 4.75 58. 2 Pcs. Terminal Lug, Sa 135, Solderless 196.00 59. 19 Bags Tile Adhesive Cement, 25kgs 452.00 60. 12 Kgs Tile Grout 97.50 61. 7 Length Tile Trim (1/2" X 2.40m) 320.00 62. 6 Gal Topcoat, Latex (lime) 930.00 63. 4 Gal Topcoat, Latex (maroon) 930.00 64. 8 Gal Topcoat, Latex (pantone 148c) 930.00 65. 4 Gal Topcoat, Latex (pantone 313c) 930.00 66. 2 Gal Topcoat, Latex (pantone 802c) 930.00 67. 5 Gal Topcoat, Latex (royal Blue) 930.00 68. 15 Pcs. Utility Box, 2"x 4" Upvc, Orange Color 32.00 69. 48 Length Wall Angle (25mm X 25mm X 0.4mm X 2.44m) 80.50 70. 350 Pc W-clip/double Furring Clip 18.00 Total Brand Model:_____________ Delivery Period:______________________ Warranty: After Having Carefully Read & Accepted Your General Conditions. I/we Quote On The Item/s Price/s Noted Above. Total Bid Price (in Words) Bid Security: Amount: Submitted By: Bidder/supplier Date:_________________________
Closing Soon25 Nov 2024
Tender AmountPHP 583.8 K (USD 9.9 K)
4791-4800 of 4849 active Tenders