Architect Tenders

Details: Description Republic Of The Philippines Department Of Justice Bureau Of Corrections Muntinlupa City Philippine Bidding Documents Renovation Of Accounting Office (procurement/ Id No. 07) Sixth Edition July 2020 Bids And Awards Committee 2024 Table Of Contents Section I. Invitation To Bid 3 Section Ii. Instructions To Bidders 6 Section Iii. Bid Data Sheet 13 Section Iv. General Conditions Of Contract 16 Section V. Special Conditions Of Contract 21 Section Vi. Specifications 23 Section Vii. Drawings 26 Section Viii. Bill Of Quantities 40 Section Ix. Checklist Of Technical And Financial Documents 42 Section I. Invitation To Bid Republic Of The Philippines Department Of Justice Bureau Of Corrections Muntinlupa City Invitation To Bid Renovation Of Accounting Office 1. The Bureau Of Corrections, Through The General Appropriations Act (gaa) Of 2024 Intends To Apply The Sum Of Two Million Five Hundred Fifty-five Thousand Eight Hundred Eighty Pesos And 86/100 (₱2,555,880.86) Being The Approved Budget For The Contract (abc) To Payments Under The Contract For Renovation Of Accounting Office With Identification Number _07__. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. 2. The Bureau Of Corrections Now Invites Bids For The Above Procurement Project. Completion Of The Works Is Required Within One Hundred Eighty (180) Calendar Days From The Date Of Issuance Of Notice To Proceed. Bidders Should Have Completed A Contract Similar To The Project Amounting To At Least Fifty Percent (50%) Of The Abc Within The Last Four (4) Years. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii (instructions To Bidders). 3. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) No. 9184. 4. Interested Bidders May Obtain Further Information From Bureau Of Corrections And Inspect The Bidding Documents At The Address Given Below From Monday To Friday From 8:00am To 5:00pm. 5. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders On ___february 29, 2024 (08:00am To 05:00pm) To March 26, 2024 (08:00am To 01:29pm) From The Given Address And Website(s) Below. It May Also Be Downloaded Free Of Charge From The Website Of The Philippine Government Electronic Procurement System (philgeps) And The Website Of The Procuring Entity Bucor.gov.ph, Provided That Bidders Shall Pay The Applicable Fee Of Five Thousand (₱5,000.00) Pesos Only For The Bidding Documents Not Later Than The Submission Of Their Bids. The Procuring Entity Shall Allow The Bidder To Present Its Proof Of Payment For The Fees In Person Or By Facsimile. 6. The Bureau Of Corrections Will Hold A Pre-bid Conference On_ March 12, 2024 (01:30pm) At Bac Conference Room Nbp Reservation Muntinlupa City, Which Shall Be Open To Prospective Bidders. 7. Bids Must Be Duly Received By The Bac Secretariat Through Manual Submission At The Office Address As Indicated Below, On Or Before _march 26, 2024_( 01:30pm)__. Late Bids Shall Not Be Accepted. 8. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 15. 9. Bid Opening Shall Be On __march 26, 2024 (01:30pm)_ At The Bac Conference Room Nbp Reservation Muntinlupa City. Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend The Activity. 10. The Bureau Of Corrections Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Implementing Rules And Regulations (irr) Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 11. For Further Information, Please Refer To: Ma. Adoracion I. Viñas Office Of The Bac Secretariat Supply Office, Bureau Of Corrections, Muntinlupa City Tel # 02-8809-8587/02-8478-0907 Bacsec2022@gmail.com 13. You May Visit The Following Websites: For Downloading Of Bidding Documents: Bucor.gov.ph Date Of Issue: _______________ Ccsupt Celso S Bravo Chairman, Bids And Awards Committee Section Ii. Instructions To Bidders 1. Scope Of Bid The Procuring Entity, Bureau Of Corrections Invites Bids For The Renovation Of Accounting Office, With Project Identification Number [indicate Number]. [note: The Project Identification Number Is Assigned By The Procuring Entity Based On Its Own Coding Scheme And Is Not The Same As The Philgeps Reference Number, Which Is Generated After The Posting Of The Bid Opportunity On The Philgeps Website.] The Procurement Project (referred To Herein As “project”) Is For The Construction Of Works, As Described In Section Vi (specifications). 2. Funding Information 2.1. The Gop Through The Source Of Funding Through The General Appropriations Act (gaa) Of 2024 In The Amount Of Two Million Five Hundred Fifty-five Thousand Eight Hundred Eighty Pesos And 86/100 (₱2,555,880.86). 2.2. The Source Of Funding Is: A. Nga, The General Appropriations Act Or Special Appropriations. 3. Bidding Requirements The Bidding For The Project Shall Be Governed By All The Provisions Of Ra No. 9184 And Its 2016 Revised Irr, Including Its Generic Procurement Manual And Associated Policies, Rules And Regulations As The Primary Source Thereof, While The Herein Clauses Shall Serve As The Secondary Source Thereof. Any Amendments Made To The Irr And Other Gppb Issuances Shall Be Applicable Only To The Ongoing Posting, Advertisement, Or Invitation To Bid By The Bac Through The Issuance Of A Supplemental Or Bid Bulletin. The Bidder, By The Act Of Submitting Its Bid, Shall Be Deemed To Have Inspected The Site, Determined The General Characteristics Of The Contracted Works And The Conditions For This Project, Such As The Location And The Nature Of The Work; (b) Climatic Conditions; (c) Transportation Facilities; (c) Nature And Condition Of The Terrain, Geological Conditions At The Site Communication Facilities, Requirements, Location And Availability Of Construction Aggregates And Other Materials, Labor, Water, Electric Power And Access Roads; And (d) Other Factors That May Affect The Cost, Duration And Execution Or Implementation Of The Contract, Project, Or Work And Examine All Instructions, Forms, Terms, And Project Requirements In The Bidding Documents. 4. Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices The Procuring Entity, As Well As The Bidders And Contractors, Shall Observe The Highest Standard Of Ethics During The Procurement And Execution Of The Contract. They Or Through An Agent Shall Not Engage In Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices Defined Under Annex “i” Of The 2016 Revised Irr Of Ra No. 9184 Or Other Integrity Violations In Competing For The Project. 5. Eligible Bidders 5.1. Only Bids Of Bidders Found To Be Legally, Technically, And Financially Capable Will Be Evaluated. 5.2. The Bidder Must Have An Experience Of Having Completed A Single Largest Completed Contract (slcc) That Is Similar To This Project, Equivalent To At Least Fifty Percent (50%) Of The Abc Adjusted, If Necessary, By The Bidder To Current Prices Using The Psa’s Cpi, Except Under Conditions Provided For In Section 23.4.2.4 Of The 2016 Revised Irr Of Ra No. 9184. A Contract Is Considered To Be “similar” To The Contract To Be Bid If It Has The Major Categories Of Work Stated In The Bds. 5.3. For Foreign-funded Procurement, The Procuring Entity And The Foreign Government/foreign Or International Financing Institution May Agree On Another Track Record Requirement, As Specified In The Bidding Document Prepared For This Purpose. 5.4. The Bidders Shall Comply With The Eligibility Criteria Under Section 23.4.2 Of The 2016 Irr Of Ra No. 9184. 6. Origin Of Associated Goods There Is No Restriction On The Origin Of Goods Other Than Those Prohibited By A Decision Of The Un Security Council Taken Under Chapter Vii Of The Charter Of The Un. 7. Subcontracts 7.1. The Bidder May Subcontract Portions Of The Project To The Extent Allowed By The Procuring Entity As Stated Herein, But In No Case More Than Fifty Percent (50%) Of The Project. The Procuring Entity Has Prescribed That: A. Subcontracting Is Not Allowed. 7.1. [if Procuring Entity Has Determined That Subcontracting Is Allowed During The Bidding, State:] The Bidder Must Submit Together With Its Bid The Documentary Requirements Of The Subcontractor(s) Complying With The Eligibility Criteria Stated In Itb Clause 5 In Accordance With Section 23.4 Of The 2016 Revised Irr Of Ra No. 9184 Pursuant To Section 23.1 Thereof. 7.2. [if Subcontracting Is Allowed During The Contract Implementation Stage, State:] The Supplier May Identify Its Subcontractor During The Contract Implementation Stage. Subcontractors Identified During The Bidding May Be Changed During The Implementation Of This Contract. Subcontractors Must Submit The Documentary Requirements Under Section 23.1 Of The 2016 Revised Irr Of Ra No. 9184 And Comply With The Eligibility Criteria Specified In Itb Clause 5 To The Implementing Or End-user Unit. 7.3. Subcontracting Of Any Portion Of The Project Does Not Relieve The Contractor Of Any Liability Or Obligation Under The Contract. The Supplier Will Be Responsible For The Acts, Defaults, And Negligence Of Any Subcontractor, Its Agents, Servants, Or Workmen As Fully As If These Were The Contractor’s Own Acts, Defaults, Or Negligence, Or Those Of Its Agents, Servants, Or Workmen. 8. Pre-bid Conference The Procuring Entity Will Hold A Pre-bid Conference For This Project On The Specified Date And Time And Either At Its Physical Address At Bac Conference Room Nbp Reservation Muntinlupa City And/or Through Videoconferencing/webcasting} As Indicated In Paragraph 6 Of The Ib. 9. Clarification And Amendment Of Bidding Documents Prospective Bidders May Request For Clarification On And/or Interpretation Of Any Part Of The Bidding Documents. Such Requests Must Be In Writing And Received By The Procuring Entity, Either At Its Given Address Or Through Electronic Mail Indicated In The Ib, At Least Ten (10) Calendar Days Before The Deadline Set For The Submission And Receipt Of Bids. 10. Documents Comprising The Bid: Eligibility And Technical Components 10.1. The First Envelope Shall Contain The Eligibility And Technical Documents Of The Bid As Specified In Section Ix. Checklist Of Technical And Financial Documents. 10.2. If The Eligibility Requirements Or Statements, The Bids, And All Other Documents For Submission To The Bac Are In Foreign Language Other Than English, It Must Be Accompanied By A Translation In English, Which Shall Be Authenticated By The Appropriate Philippine Foreign Service Establishment, Post, Or The Equivalent Office Having Jurisdiction Over The Foreign Bidder’s Affairs In The Philippines. For Contracting Parties To The Apostille Convention, Only The Translated Documents Shall Be Authenticated Through An Apostille Pursuant To Gppb Resolution No. 13-2019 Dated 23 May 2019. The English Translation Shall Govern, For Purposes Of Interpretation Of The Bid. 10.3. A Valid Pcab License Is Required, And In Case Of Joint Ventures, A Valid Special Pcab License, And Registration For The Type And Cost Of The Contract For This Project. Any Additional Type Of Contractor License Or Permit Shall Be Indicated In The Bds. 10.4. A List Of Contractor’s Key Personnel (e.g., Project Manager, Project Engineers, Materials Engineers, And Foremen) Assigned To The Contract To Be Bid, With Their Complete Qualification And Experience Data Shall Be Provided. These Key Personnel Must Meet The Required Minimum Years Of Experience Set In The Bds. 10.5. A List Of Contractor’s Major Equipment Units, Which Are Owned, Leased, And/or Under Purchase Agreements, Supported By Proof Of Ownership, Certification Of Availability Of Equipment From The Equipment Lessor/vendor For The Duration Of The Project, As The Case May Be, Must Meet The Minimum Requirements For The Contract Set In The Bds. 11. Documents Comprising The Bid: Financial Component 11.1. The Second Bid Envelope Shall Contain The Financial Documents For The Bid As Specified In Section Ix. Checklist Of Technical And Financial Documents. 11.2. Any Bid Exceeding The Abc Indicated In Paragraph 1 Of The Ib Shall Not Be Accepted. 11.3. For Foreign-funded Procurement, A Ceiling May Be Applied To Bid Prices Provided The Conditions Are Met Under Section 31.2 Of The 2016 Revised Irr Of Ra No. 9184. 12. Alternative Bids Bidders Shall Submit Offers That Comply With The Requirements Of The Bidding Documents, Including The Basic Technical Design As Indicated In The Drawings And Specifications. Unless There Is A Value Engineering Clause In The Bds, Alternative Bids Shall Not Be Accepted. 13. Bid Prices All Bid Prices For The Given Scope Of Work In The Project As Awarded Shall Be Considered As Fixed Prices, And Therefore Not Subject To Price Escalation During Contract Implementation, Except Under Extraordinary Circumstances As Determined By The Neda And Approved By The Gppb Pursuant To The Revised Guidelines For Contract Price Escalation Guidelines. 14. Bid And Payment Currencies 14.1. Bid Prices May Be Quoted In The Local Currency Or Tradable Currency Accepted By The Bsp At The Discretion Of The Bidder. However, For Purposes Of Bid Evaluation, Bids Denominated In Foreign Currencies Shall Be Converted To Philippine Currency Based On The Exchange Rate As Published In The Bsp Reference Rate Bulletin On The Day Of The Bid Opening. 14.2. Payment Of The Contract Price Shall Be Made In: A. Philippine Pesos. 15. Bid Security 15.1. The Bidder Shall Submit A Bid Securing Declaration Or Any Form Of Bid Security In The Amount Indicated In The Bds, Which Shall Be Not Less Than The Percentage Of The Abc In Accordance With The Schedule In The Bds. 15.2. The Bid And Bid Security Shall Be Valid Until One Hundred Twenty (120) Calendar Days. Any Bid Not Accompanied By An Acceptable Bid Security Shall Be Rejected By The Procuring Entity As Non-responsive. 16. Sealing And Marking Of Bids Each Bidder Shall Submit One Copy Of The First And Second Components Of Its Bid. The Procuring Entity May Request Additional Hard Copies And/or Electronic Copies Of The Bid. However, Failure Of The Bidders To Comply With The Said Request Shall Not Be A Ground For Disqualification. If The Procuring Entity Allows The Submission Of Bids Through Online Submission To The Given Website Or Any Other Electronic Means, The Bidder Shall Submit An Electronic Copy Of Its Bid, Which Must Be Digitally Signed. An Electronic Copy That Cannot Be Opened Or Is Corrupted Shall Be Considered Non-responsive And, Thus, Automatically Disqualified. 17. Deadline For Submission Of Bids The Bidders Shall Submit On The Specified Date And Time And Either At Its Physical Address Or Through Online Submission As Indicated In Paragraph 7 Of The Ib. 18. Opening And Preliminary Examination Of Bids 18.1. The Bac Shall Open The Bids In Public At The Time, On The Date, And At The Place Specified In Paragraph 9 Of The Ib. The Bidders’ Representatives Who Are Present Shall Sign A Register Evidencing Their Attendance. In Case Videoconferencing, Webcasting Or Other Similar Technologies Will Be Used, Attendance Of Participants Shall Likewise Be Recorded By The Bac Secretariat. In Case The Bids Cannot Be Opened As Scheduled Due To Justifiable Reasons, The Rescheduling Requirements Under Section 29 Of The 2016 Revised Irr Of Ra No. 9184 Shall Prevail. 18.2. The Preliminary Examination Of Bids Shall Be Governed By Section 30 Of The 2016 Revised Irr Of Ra No. 9184. 19. Detailed Evaluation And Comparison Of Bids 19.1. The Procuring Entity’s Bac Shall Immediately Conduct A Detailed Evaluation Of All Bids Rated “passed” Using Non-discretionary Pass/fail Criteria. The Bac Shall Consider The Conditions In The Evaluation Of Bids Under Section 32.2 Of 2016 Revised Irr Of Ra No. 9184. 19.2. If The Project Allows Partial Bids, All Bids And Combinations Of Bids As Indicated In The Bds Shall Be Received By The Same Deadline And Opened And Evaluated Simultaneously So As To Determine The Bid Or Combination Of Bids Offering The Lowest Calculated Cost To The Procuring Entity. Bid Security As Required By Itb Clause 16 Shall Be Submitted For Each Contract (lot) Separately. 19.3. In All Cases, The Nfcc Computation Pursuant To Section 23.4.2.6 Of The 2016 Revised Irr Of Ra No. 9184 Must Be Sufficient For The Total Of The Abcs For All The Lots Participated In By The Prospective Bidder. 20. Post Qualification Within A Non-extendible Period Of Five (5) Calendar Days From Receipt By The Bidder Of The Notice From The Bac That It Submitted The Lowest Calculated Bid, The Bidder Shall Submit Its Latest Income And Business Tax Returns Filed And Paid Through The Bir Electronic Filing And Payment System (efps), And Other Appropriate Licenses And Permits Required By Law And Stated In The Bds. 21. Signing Of The Contract The Documents Required In Section 37.2 Of The 2016 Revised Irr Of Ra No. 9184 Shall Form Part Of The Contract. Additional Contract Documents Are Indicated In The Bds. Section Iii. Bid Data Sheet Bid Data Sheet Itb Clause 5.2 For This Purpose, Contracts Similar To The Project Refer To Contracts Which Have The Same Major Categories Of Work, Which Shall Be: Repair, Rehabilitation And Infrastructure/construction Works. 7.1 Subcontracting Is Not Allowed 10.3 A Valid Pcab License Is Required, And In Case Of Joint Ventures, A Valid Special Pcab License, And Registration For The Type And Cost Of The Contract For This Project. 10.4 The Key Personnel Must Meet The Required Minimum Years Of Experience Set Below: Key Personnel General Experience Relevant Experience Project Manager Duly Licensed Civil Engineer/architect With At Least 5 Years’ Experience Similar Or Comparable Projects, With Know- Ledge In The Application Of Rapid Construction Foreman With At Least 5 Years’ Experience As Foreman Similar Or Comparable Projects, With Know- Ledge In The Application Of Rapid Construction 10.5 The Minimum Major Equipment Requirements Are The Following: Equipment Capacity Number Of Units Service Vehicle For Hauling Of Materials One (1) Welding Machine 300 Amps One (1) Electric Grinder Heavy Duty Five (5) Electric Drill Heavy Duty Five (5) 12 No Further Instructions. 15.1 The Bid Security Shall Be In The Form Of A Bid Securing Declaration Or Any Of The Following Forms And Amounts: A. The Amount Of Not Less Than 2% Of The Abc, If Bid Security Is In Cash, Cashier’s/manager’s Check, Bank Draft/guarantee Or Irrevocable Letter Of Credit; B. The Amount Of Not Less Than 5% Of The Abc, If Bid Security Is In Surety Bond. 19.2 No Further Instructions. 20 Within A Non-extendible Period Of Five (5) Calendar Days From Receipt By The Bidder Of The Notice From The Bac That It Submitted The Lowest Calculated Bid, The Bidder Shall Submit Its; 1. Latest Income And Business Tax Returns Filed And Paid Through The Bir Electronic Filing And Payment System (efps) 2. Supporting Documents For The Slcc (notice Of Award And/or Notice To Proceed And Project Owner’s Certificate Of Final Acceptance Issued By The Owner Other Than The Contractor Or The Constructors Performance Evaluation System (cpes) Final Rating, Which Must Be At Least Satisfactory. In Case Of Contracts With The Private Sector, An Equivalent Document Shall Be Submitted) 3. Certified True Copy Coming From The Issuing Agency Of Valid And Current Registration Certificate (sec Certificate Of Registration For Corporation Or Dti Certificate Of Registration For Sole Proprietorship Or Cda Certificate Of Registration For Cooperative) 4. Valid And Current Mayor’s Or Business Permit 5. Valid And Current Tax Clearance 6. Valid And Current Pcab License And Registration 7. Audited Financial Statement 8. Copy 1 And Copy 2 Of Eligibility And Financial Bid Envelopes 21 A. Pert/cpm Or Other Acceptable Tools Of Project Scheduling B. Construction Methodology C. Manpower Utilization Schedule D. Equipment Utilization Schedule Section Iv. General Conditions Of Contract 1. Scope Of Contract This Contract Shall Include All Such Items, Although Not Specifically Mentioned, That Can Be Reasonably Inferred As Being Required For Its Completion As If Such Items Were Expressly Mentioned Herein. All The Provisions Of Ra No. 9184 And Its 2016 Revised Irr, Including The Generic Procurement Manual, And Associated Issuances, Constitute The Primary Source For The Terms And Conditions Of The Contract, And Thus, Applicable In Contract Implementation. Herein Clauses Shall Serve As The Secondary Source For The Terms And Conditions Of The Contract. This Is Without Prejudice To Sections 74.1 And 74.2 Of The 2016 Revised Irr Of Ra No. 9184 Allowing The Gppb To Amend The Irr, Which Shall Be Applied To All Procurement Activities, The Advertisement, Posting, Or Invitation Of Which Were Issued After The Effectivity Of The Said Amendment. 2. Sectional Completion Of Works If Sectional Completion Is Specified In The Special Conditions Of Contract (scc), References In The Conditions Of Contract To The Works, The Completion Date, And The Intended Completion Date Shall Apply To Any Section Of The Works (other Than References To The Completion Date And Intended Completion Date For The Whole Of The Works). 3. Possession Of Site 3.1 The Procuring Entity Shall Give Possession Of All Or Parts Of The Site To The Contractor Based On The Schedule Of Delivery Indicated In The Scc, Which Corresponds To The Execution Of The Works. If The Contractor Suffers Delay Or Incurs Cost From Failure On The Part Of The Procuring Entity To Give Possession In Accordance With The Terms Of This Clause, The Procuring Entity’s Representative Shall Give The Contractor A Contract Time Extension And Certify Such Sum As Fair To Cover The Cost Incurred, Which Sum Shall Be Paid By Procuring Entity. 3.2 If Possession Of A Portion Is Not Given By The Above Date, The Procuring Entity Will Be Deemed To Have Delayed The Start Of The Relevant Activities. The Resulting Adjustments In Contract Time To Address Such Delay May Be Addressed Through Contract Extension Provided Under Annex “e” Of The 2016 Revised Irr Of Ra No. 9184. 4. The Contractor’s Obligations The Contractor Shall Employ The Key Personnel Named In The Schedule Of Key Personnel Indicating Their Designation, In Accordance With Itb Clause 10.3 And Specified In The Bds, To Carry Out The Supervision Of The Works. The Procuring Entity Will Approve Any Proposed Replacement Of Key Personnel Only If Their Relevant Qualifications And Abilities Are Equal To Or Better Than Those Of The Personnel Listed In The Schedule. 5. Performance Security 5.1. Within Ten (10) Calendar Days From Receipt Of The Notice Of Award From The Procuring Entity But In No Case Later Than The Signing Of The Contract By Both Parties, The Successful Bidder Shall Furnish The Performance Security In Any Of The Forms Prescribed In Section 39 Of The 2016 Revised Irr. 5.2. The Contractor, By Entering Into The Contract With The Procuring Entity, Acknowledges The Right Of The Procuring Entity To Institute Action Pursuant To Ra No. 3688 Against Any Subcontractor Be They An Individual, Firm, Partnership, Corporation, Or Association Supplying The Contractor With Labor, Materials And/or Equipment For The Performance Of This Contract. 6. Site Investigation Reports The Contractor, In Preparing The Bid, Shall Rely On Any Site Investigation Reports Referred To In The Scc Supplemented By Any Information Obtained By The Contractor. 7. Warranty 7.1. In Case The Contractor Fails To Undertake The Repair Works Under Section 62.2.2 Of The 2016 Revised Irr, The Procuring Entity Shall Forfeit Its Performance Security, Subject Its Property (ies) To Attachment Or Garnishment Proceedings, And Perpetually Disqualify It From Participating In Any Public Bidding. All Payables Of The Gop In His Favor Shall Be Offset To Recover The Costs. 7.2. The Warranty Against Structural Defects/failures, Except That Occasioned-on Force Majeure, Shall Cover The Period From The Date Of Issuance Of The Certificate Of Final Acceptance By The Procuring Entity. Specific Duration Of The Warranty Is Found In The Scc. 8. Liability Of The Contractor Subject To Additional Provisions, If Any, Set Forth In The Scc, The Contractor’s Liability Under This Contract Shall Be As Provided By The Laws Of The Republic Of The Philippines. If The Contractor Is A Joint Venture, All Partners To The Joint Venture Shall Be Jointly And Severally Liable To The Procuring Entity. 9. Termination For Other Causes Contract Termination Shall Be Initiated In Case It Is Determined Prima Facie By The Procuring Entity That The Contractor Has Engaged, Before, Or During The Implementation Of The Contract, In Unlawful Deeds And Behaviors Relative To Contract Acquisition And Implementation, Such As, But Not Limited To Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices As Stated In Itb Clause 4. 10. Dayworks Subject To The Guidelines On Variation Order In Annex “e” Of The 2016 Revised Irr Of Ra No. 9184, And If Applicable As Indicated In The Scc, The Dayworks Rates In The Contractor’s Bid Shall Be Used For Small Additional Amounts Of Work Only When The Procuring Entity’s Representative Has Given Written Instructions In Advance For Additional Work To Be Paid For In That Way. 11. Program Of Work 11.1. The Contractor Shall Submit To The Procuring Entity’s Representative For Approval The Said Program Of Work Showing The General Methods, Arrangements, Order, And Timing For All The Activities In The Works. The Submissions Of The Program Of Work Are Indicated In The Scc. 11.2. The Contractor Shall Submit To The Procuring Entity’s Representative For Approval An Updated Program Of Work At Intervals No Longer Than The Period Stated In The Scc. If The Contractor Does Not Submit An Updated Program Of Work Within This Period, The Procuring Entity’s Representative May Withhold The Amount Stated In The Scc From The Next Payment Certificate And Continue To Withhold This Amount Until The Next Payment After The Date On Which The Overdue Program Of Work Has Been Submitted. 12. Instructions, Inspections And Audits The Contractor Shall Permit The Gop Or The Procuring Entity To Inspect The Contractor’s Accounts And Records Relating To The Performance Of The Contractor And To Have Them Audited By Auditors Of The Gop Or The Procuring Entity, As May Be Required. 13. Advance Payment The Procuring Entity Shall, Upon A Written Request Of The Contractor Which Shall Be Submitted As A Contract Document, Make An Advance Payment To The Contractor In An Amount Not Exceeding Fifteen Percent (15%) Of The Total Contract Price, To Be Made In Lump Sum, Or At The Most Two Installments According To A Schedule Specified In The Scc, Subject To The Requirements In Annex “e” Of The 2016 Revised Irr Of Ra No. 9184. 14. Progress Payments The Contractor May Submit A Request For Payment For Work Accomplished. Such Requests For Payment Shall Be Verified And Certified By The Procuring Entity’s Representative/project Engineer. Except As Otherwise Stipulated In The Scc, Materials And Equipment Delivered On The Site But Not Completely Put In Place Shall Not Be Included For Payment. 15. Operating And Maintenance Manuals 15.1. If Required, The Contractor Will Provide “as Built” Drawings And/or Operating And Maintenance Manuals As Specified In The Scc. 15.2. If The Contractor Does Not Provide The Drawings And/or Manuals By The Dates Stated Above, Or They Do Not Receive The Procuring Entity’s Representative’s Approval, The Procuring Entity’s Representative May Withhold The Amount Stated In The Scc From Payments Due To The Contractor. Section V. Special Conditions Of Contract Special Conditions Of Contract Gcc Clause 2 Sectional Completion Is Not Applicable The Intended Completion Date Is One Hundred Eighty (180) Calendar Days From The Date Of Receipt Of The Ntp. 4.1 The Procuring Entity Shall Give Possession Of All Parts Of The Site To The Contractor From The Date Of The Receipt Of Notice To Proceed (ntp). 6 No Further Instructions. 7.2 Five (5) Years. 10 No Dayworks Are Applicable To The Contract. 11.1 The Contractor Shall Submit The Program Of Work To The Procuring Entity’s Representative Within Fourteen (14) Days Of Delivery Of The Notice Of Award. 11.2 The Amount To Be Withheld For Late Submission Of An Updated Program Of Work Is [insert Amount]. 13 The Amount Of The Advance Payment Is Fifteen Percent (15%) Of The Contract Price To Be Made In Lump Sum Upon Submission To And Acceptance By The Bureau Of Corrections Of An Irrevocable Standby Letter Of Credit Of Equivalent Value From A Commercial Bank, A Bank Guarantee Or A Surety Bond Callable Upon Demand Issued By A Surety Or Insurance Company Duly Licensed By The Insurance Commission And Confirmed By The Bureau Of Corrections. 14 Materials And Equipment Delivered On The Site But Not Completely Put In Place Shall Not Be Included For Payment. 15.1 The Date By Which Operating And Maintenance Manuals Are Required Is Upon Actual Completion Of The Project. The Date By Which “as Built” Drawings Are Required Is Upon Actual Completion Of The Project. 15.2 The Amount To Be Withheld For Failing To Produce “as Built” Drawings And/or Operating And Maintenance Manuals By The Date Required Is Equivalent To Five Percent (5%) Of The Contract Price. Section Vi. Specifications Contract Duration: 180 Calendar Days Conforme: Name Of Company In Print Signature Over Printed Name Of Authorized Representative/date Contract Duration: 180 Calendar Days Conforme: Name Of Company In Print Signature Over Printed Name Of Authorized Representative/date Section Vii. Drawings Conforme: Name Of Company In Print Signature Over Printed Name Of Authorized Representative/date Conforme: Name Of Company In Print Signature Over Printed Name Of Authorized Representative/date Conforme: Name Of Company In Print Signature Over Printed Name Of Authorized Representative/date Conforme: Name Of Company In Print Signature Over Printed Name Of Authorized Representative/date Conforme: Name Of Company In Print Signature Over Printed Name Of Authorized Representative/date Conforme: Name Of Company In Print Signature Over Printed Name Of Authorized Representative/date Conforme: Name Of Company In Print Signature Over Printed Name Of Authorized Representative/date Conforme: Name Of Company In Print Signature Over Printed Name Of Authorized Representative/date Conforme: Name Of Company In Print Signature Over Printed Name Of Authorized Representative/date Conforme: Name Of Company In Print Signature Over Printed Name Of Authorized Representative/date Conforme: Name Of Company In Print Signature Over Printed Name Of Authorized Representative/date Conforme: Name Of Company In Print Signature Over Printed Name Of Authorized Representative/date Conforme: Name Of Company In Print Signature Over Printed Name Of Authorized Representative/date Section Viii. Bill Of Quantities Republic Of The Philippines Department Of Justice Bureau Of Corrections Muntinlupa City Submitted By: ______________________________ Contractor/authorized Representatives Section Ix. Checklist Of Technical And Financial Documents Checklist Of Technical And Financial Documents I. Technical Component Envelope Class “a” Documents Legal Documents ⬜ (a) Valid Philgeps Registration Certificate (platinum Membership) (all Pages); Technical Documents ⬜ (b) Statement Of The Prospective Bidder Of All Its Ongoing Government And Private Contracts, Including Contracts Awarded But Not Yet Started, If Any, Whether Similar Or Not Similar In Nature And Complexity To The Contract To Be Bid; And ⬜ (c) Statement Of The Bidder’s Single Largest Completed Contract (slcc) Similar To The Contract To Be Bid, Except Under Conditions Provided Under The Rules; And ⬜ (d) Original Copy Of Bid Security. If In The Form Of A Surety Bond, Submit Also A Certification Issued By The Insurance Commission; Or Original Copy Of Notarized Bid Securing Declaration; And (e) Project Requirements, Which Shall Include The Following: ⬜ A. Organizational Chart For The Contract To Be Bid; ⬜ B. List Of Contractor’s Key Personnel (e.g., Project Manager, Project Engineers, Materials Engineers, And Foremen), To Be Assigned To The Contract To Be Bid, With Their Complete Qualification And Experience Data; ⬜ C. List Of Contractor’s Major Equipment Units, Which Are Owned, Leased, And/or Under Purchase Agreements, Supported By Proof Of Ownership Or Certification Of Availability Of Equipment From The Equipment Lessor/vendor For The Duration Of The Project, As The Case May Be; And ⬜ (f) Original Duly Signed Omnibus Sworn Statement (oss); And If Applicable, Original Notarized Secretary’s Certificate Or Board Resolution For Corporation Or Original Notarized Partnership Resolution In Case Of A Partnership, Or Cooperative; Or Original Notarized Special Power Of Attorney Of All Members Of The Joint Venture Giving Full Power And Authority To Its Officer To Sign The Oss And Do Acts To Represent The Bidder. ⬜ (g) Conformity With The Technical Specifications (scope Of Work); And ⬜ (h) Conformity With The Plans/drawings. Financial Documents ⬜ (i) The Prospective Bidder’s Computation Of Net Financial Contracting Capacity (nfcc) Which Must Be At Least Equal To The Abc. Class “b” Documents ⬜ (j) If Applicable, Duly Signed Joint Venture Agreement (jva) In Accordance With Ra No. 4566 And Its Irr In Case The Joint Venture Is Already In Existence; Or Duly Notarized Statements From All The Potential Joint Venture Partners Stating That They Will Enter Into And Abide By The Provisions Of The Jva In The Instance That The Bid Is Successful. Note: Each Partner Of The Joint Venture Shall Submit Their Respective Philgeps Certificates Of Registration In Accordance With Section 8.5.2 Of This Irr. The Submission Of Technical And Financial Eligibility Documents By Any Of The Joint Venture Partners Constitutes Compliance: Provided, That The Partner Responsible To Submit The Nfcc Shall Likewise Submit The Statement Of All Of Its Ongoing Contracts And Audited Financial Statements. Ii. Financial Component Envelope ⬜ (k) Original Of Duly Signed And Accomplished Financial Bid Form; And Other Documentary Requirements Under Ra No. 9184 ⬜ (l) Original Of Duly Signed Bid Prices In The Bill Of Quantities; And ⬜ (m) Duly Accomplished Detailed Estimates Form, Including A Summary Sheet Indicating The Unit Prices Of Construction Materials, Labor Rates, And Equipment Rentals Used In Coming Up With The Bid; And ⬜ (n) Cash Flow By Quarter. Bidding Form Company Letterhead Statement Of Ongoing Government & Private Contracts Renovation Of Accounting Office Statement Of All Its Ongoing Government And Or Private Contracts Including Contracts Awarded But Not Yet Started, If Any Whether Similar Or Not Similar In Nature. Name Of Contract Date Of Contract Contract Duration Owner’s Name And Address Nature Of Work Contractor’s Role (whether Sole Contractor, Subcontractor, Or Partner In A Jv) And Percentage Of Participation Total Contract Value At Award Date Of Completion Or Estimated Completion Time Value Of Outstanding Works Certified Correct: Name And Signature Of Authorized Representative Position Date Company Letterhead Statement Of Single Largest Completed Contract Renovation Of Accounting Office Statement Of Single (1) Largest Completed Contract Of Similar In Nature Within The Last Four (4) Years From The Date Of Submission And Receipt Of Bids Amounting To At Least Fifty Percent (50%) Of The Approved Budget Of The Contract (abc) Name Of Contract Date Of Contract Contract Duration Owner’s Name And Address Nature Of Work Contractor’s Role (whether Sole Contractor, Subcontractor, Or Partner In A Jv) And Percentage Of Participation Total Contract Value At Award Date Of Completion Or Estimated Completion Time Certified Correct: Name And Signature Of Authorized Representative Position Date Company Letterhead Renovation Of Accounting Office Republic Of The Philippines) City Of _______________________) S.s. X------------------------------------------------------x Bid Securing Declaration Invitation To Bid: [insert Reference Number] To: Bureau Of Corrections I/we, The Undersigned, Declare That: 1. I/we Understand That, According To Your Conditions, Bids Must Be Supported By A Bid Security, Which May Be In The Form Of A Bid-securing Declaration. 2. I/we Accept That: (a) I/we Will Be Automatically Disqualified From Bidding For Any Contract With Any Procuring Entity For A Period Of Two (2) Years Upon Receipt Of Your Blacklisting Order; And, (b) I/we Will Pay The Applicable Fine Provided Under Section 6 Of The Guidelines On The Use Of Bid Securing Declaration, Within Fifteen (15) Days From Receipt Of The Written Demand By The Procuring Entity For The Commission Of Acts Resulting To The Enforcement Of The Bid Securing Declaration Under Sections 23.1(b), 34.2, 40.1 And 69.1, Except 69.1(f), Of The Irr Of Ra 9184; Without Prejudice To Other Legal Action The Government May Undertake. 3. I/we Understand That This Bid Securing Declaration Shall Cease To Be Valid On The Following Circumstances: (a) Upon Expiration Of The Bid Validity Period, Or Any Extension Thereof Pursuant To Your Request; (b) I Am/we Are Declared Ineligible Or Post-disqualified Upon Receipt Of Your Notice To Such Effect, And (i) I/we Failed To Timely File A Request For Reconsideration Or (ii) I/we Filed A Waiver To Avail Of Said Right; (c) I Am/we Are Declared The Bidder With The Lowest Calculated Responsive Bid, And I/we Have Furnished The Performance Security And Signed The Contract. In Witness Whereof, I/we Have Hereunto Set My/our Hand/s This ____ Day Of [month] [year] At [place Of Execution]. ______________________________________________________ [insert Name Of Bidder’s Authorized Representative] _____________________________ [insert Signatory’s Legal Capacity] Affiant Subscribed And Sworn To Before Me This ___ Day Of [month] [year] At [place Of Execution], Philippines. Affiant/s Is/are Personally Known To Me And Was/were Identified By Me Through Competent Evidence Of Identity As Defined In The 2004 Rules On Notarial Practice (a.m. No. 02-8-13-sc). Affiant/s Exhibited To Me His/her [insert Type Of Government Identification Card Used], With His/her Photograph And Signature Appearing Thereon, With No. ____________ Issued On ______________ At ___________________________________. Witness My Hand And Seal This ___ Day Of [month] [year]. Name Of Notary Public Serial No. Of Commission _______________ Notary Public For _______ Until __________ Roll Of Attorneys No. __________________ Ptr No. ______ [date Issued], [place Issued] Ibp No. ______ [date Issued], [place Issued] Doc. No. _____ Page No. _____ Book No. _____ Series Of ____ Company Letterhead Omnibus Sworn Statement Renovation Of Accounting Office _________________________________________________________________________ Republic Of The Philippines ) City/municipality Of ______ ) S.s. Affidavit I, [name Of Affiant], Of Legal Age, [civil Status], [nationality], And Residing At [address Of Affiant], After Having Been Duly Sworn In Accordance With Law, Do Hereby Depose And State That: 1. [select One, Delete The Other:] [if A Sole Proprietorship:] I Am The Sole Proprietor Or Authorized Representative Of [name Of Bidder] With Office Address At [address Of Bidder]; [if A Partnership, Corporation, Cooperative, Or Joint Venture:] I Am The Duly Authorized And Designated Representative Of [name Of Bidder] With Office Address At [address Of Bidder]; 2. [select One, Delete The Other:] [if A Sole Proprietorship:] As The Owner And Sole Proprietor, Or Authorized Representative Of [name Of Bidder], I Have Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For Renovation Of Accounting Office Of The Bureau Of Corrections, As Shown In The Attached Duly Notarized Special Power Of Attorney; [if A Partnership, Corporation, Cooperative, Or Joint Venture:] I Am Granted Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For Renovation Of Accounting Office Of The Bureau Of Corrections, As Shown In The Attached [state Title Of Attached Document Showing Proof Of Authorization (e.g., Duly Notarized Secretary’s Certificate, Board/partnership Resolution, Or Special Power Of Attorney, Whichever Is Applicable;)]; 3. [name Of Bidder] Is Not “blacklisted” Or Barred From Bidding By The Government Of The Philippines Or Any Of Its Agencies, Offices, Corporations, Or Local Government Units, Foreign Government/foreign Or International Financing Institution Whose Blacklisting Rules Have Been Recognized By The Government Procurement Policy Board, By Itself Or By Relation, Membership, Association, Affiliation, Or Controlling Interest With Another Blacklisted Person Or Entity As Defined And Provided For In The Uniform Guidelines On Blacklisting; 4. Each Of The Documents Submitted In Satisfaction Of The Bidding Requirements Is An Authentic Copy Of The Original, Complete, And All Statements And Information Provided Therein Are True And Correct; 5. [name Of Bidder] Is Authorizing The Head Of The Procuring Entity Or Its Duly Authorized Representative(s) To Verify All The Documents Submitted; 6. [select One, Delete The Rest:] [if A Sole Proprietorship:] The Owner Or Sole Proprietor Is Not Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; [if A Partnership Or Cooperative:] None Of The Officers And Members Of [name Of Bidder] Is Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; [if A Corporation Or Joint Venture:] None Of The Officers, Directors, And Controlling Stockholders Of [name Of Bidder] Is Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; 7. [name Of Bidder] Complies With Existing Labor Laws And Standards; And 8. [name Of Bidder] Is Aware Of And Has Undertaken The Responsibilities As A Bidder In Compliance With The Philippine Bidding Documents, Which Includes: A. Carefully Examining All Of The Bidding Documents; B. Acknowledging All Conditions, Local Or Otherwise, Affecting The Implementation Of The Contract; C. Making An Estimate Of The Facilities Available And Needed For The Contract To Be Bid, If Any; And D. Inquiring Or Securing Supplemental/bid Bulletin(s) Issued For The Renovation Of Accounting Office. 9. [name Of Bidder] Did Not Give Or Pay Directly Or Indirectly, Any Commission, Amount, Fee, Or Any Form Of Consideration, Pecuniary Or Otherwise, To Any Person Or Official, Personnel Or Representative Of The Government In Relation To Any Procurement Project Or Activity. 10. In Case Advance Payment Was Made Or Given, Failure To Perform Or Deliver Any Of The Obligations And Undertakings In The Contract Shall Be Sufficient Grounds To Constitute Criminal Liability For Swindling (estafa) Or The Commission Of Fraud With Unfaithfulness Or Abuse Of Confidence Through Misappropriating Or Converting Any Payment Received By A Person Or Entity Under An Obligation Involving The Duty To Deliver Certain Goods Or Services, To The Prejudice Of The Public And The Government Of The Philippines Pursuant To Article 315 Of Act No. 3815 S. 1930, As Amended, Or The Revised Penal Code. In Witness Whereof, I Have Hereunto Set My Hand This __ Day Of ___, 2024 At ____________, Philippines. _____________________________________ Bidder’s Representative/authorized Signatory Affiant Subscribed And Sworn To Before Me This ___ Day Of [month] [year] At [place Of Execution], Philippines. Affiant/s Is/are Personally Known To Me And Was/were Identified By Me Through Competent Evidence Of Identity As Defined In The 2004 Rules On Notarial Practice (a.m. No. 02-8-13-sc). Affiant/s Exhibited To Me His/her [insert Type Of Government Identification Card Used], With His/her Photograph And Signature Appearing Thereon, With No. ____________ And Issued On ____________________ At _____________________. Witness My Hand And Seal This ___ Day Of [month] [year]. Name Of Notary Public Serial No. Of Commission _______________ Notary Public For _______ Until __________ Roll Of Attorneys No. __________________ Ptr No. ______ [date Issued], [place Issued] Ibp No. ______ [date Issued], [place Issued] Doc. No. _____ Page No. _____ Book No. _____ Series Of _____ Company Letterhead Certificate Of Net Financial Contracting Capacity Renovation Of Accounting Office (please Show Figures At How You Arrived At The Nfcc) This Is To Certify That Our Net Financial Contracting Capacity (nfcc) Is _____________________ (p____________) Which Is At Least Equal To The Total Ceiling Price We Are Bidding. The Amount Is Computed As Follows: (please Show Computation Of Nfcc) Nfcc = (ca-cl) (15) – C Where: Ca = Current Assets Cl = Current Liabilities C = Value Of All Outstanding Or Uncompleted Portions Of The Projects Under Going Contracts, Including Awarded Contracts Yet To Be Started Coinciding With The Contract For This Project Note: The Values Of The Bidder’s Current Assets And Current Liabilities Shall Be Based On The Audited Financial Statement Submitted To The Bir. Issued This _________________day Of ________________, 2024_______________________________________________ Name & Signature Of Authorized Representative____________________ Position _______________ Date Company Letterhead Bid Form Date: Ib No: To Bids And Awards Committee Bureau Of Corrections Nbp Reservation Muntinlupa City We, The Undersigned, Declare That: (a) We Have Examined And Have No Reservation To The Bidding Documents, Including Addenda, For The Contract Renovation Of Accounting Office; (b) We Offer To Execute The Works For This Contract In Accordance With The Bid And Bid Data Sheet, General And Special Conditions Of Contract Accompanying This Bid; The Total Price Of Our Bid, Excluding Any Discounts Offered Below Is: ________________________________________₱_________________; The Discounts Offered And The Methodology For Their Application Are: [insert Information]; (c) Our Bid Shall Be Valid For A Period Of 120 Calendar Days From The Date Fixed For The Bid Submission Deadline In Accordance With The Bidding Documents, And It Shall Remain Binding Upon Us And May Be Accepted At Any Time Before The Expiration Of That Period; (d) If Our Bid Is Accepted, We Commit To Obtain A Performance Security In The Amount Of 30% Percent Of The Contract Price For The Due Performance Of The Contract; (e) Our Firm, Including Any Subcontractors Or Suppliers For Any Part Of The Contract, Have Nationalities From The Following Eligible Countries; (f) We Are Not Participating, As Bidders, In More Than One Bid In This Bidding Process, Other Than Alternative Offers In Accordance With The Bidding Documents; (g) Our Firm, Its Affiliates Or Subsidiaries, Including Any Subcontractors Or Suppliers For Any Part Of The Contract, Has Not Been Declared Ineligible By The Funding Source; (h) We Understand That This Bid, Together With Your Written Acceptance Thereof Included In Your Notification Of Award, Shall Constitute A Binding Contract Between Us, Until A Formal Contract Is Prepared And Executed; And (i) We Understand That You Are Not Bound To Accept The Lowest Calculated Bid Or Any Other Bid That You May Receive. (j) We Likewise Certify/confirm That The Undersigned, Is The Duly Authorized Representative Of The Bidder, And Granted Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For The Renovation Of Accounting Office Of The Bureau Of Corrections. (k) We Acknowledge That Failure To Sign Each And Every Page Of This Bid Form, Including The Bill Of Quantities, Shall Be A Ground For The Rejection Of Our Bid. Name: In The Capacity Of: Signed: Duly Authorized To Sign The Bid For And On Behalf Of: Date: ___________

Tender Id: Architectural Services_initial Intake | Request For Pre-qualification - Architectural Services

Details: Planning And Construction Of A Functionally Dependent Supplementary Building For A Venue In Particular For The Music And Dance Theater Sections Of The Nuremberg State Theater In The North-west Area Of The So-called Inner Courtyard Of The Congress Hall On The Former Nazi Party Rally Grounds In Nuremberg. The Supplementary Building Is Designed As A Functionally Dependent Building, The Operation Of Which Is Only Possible Due To A Meaningful Connection Both For The Audience And For The Stage Operation With The Structural Stock Of The Circular Building Torso Of The Congress Hall From The 1930s. The Vast Majority Of The Functions Required For Theater Operations Are Located In The Existing Building (not The Subject Of This Procedure). The Main Rooms To Be Created In The Supplementary Building Are: Auditorium With Rising Seating And Optimal Visual And Auditory Relationships For At Least 800 People With An Acoustically Effective Cubature Of Around 8 Cubic Meters Per Person; Projection / Sound And Light Boxes With Approx. 55 M²; The Orchestra Pit With Approx. 150 M²; The Orchestra Rehearsal Hall For The Nuremberg State Philharmonic With Approx. 400m²; Day Storage For Instruments With Approx. 82 M²; The Main Stage Including The Stage Tower With Approx. 463 M² (width Approx. 25 M, Depth Approx. 18.5 M) Plus Approx. 223 M² For Stage Technology; A Side Stage With Approx. 410 M²; A Backstage With Approx. 353 M²; A Rehearsal Stage With Approx. 460 M²; The Stage Props And Day Camp With About 55 M²; Magazine Rooms Of Different Heights As Well As Assembly And Storage Areas With A Total Of Approx. 596 M²; Evening Wear For Artists Approximately 563 Sqm; Offices, Lounges And Workshops With A Total Of Approx. 160 M²; Various Technical And Storage Rooms With A Total Of Approx. 216 M² As Well As Areas For Delivery. A Total Of Approx. 5,000 M² Of Usable Space Is To Be Planned And Built. Beyond The Time Of Completion, The Object Of Procurement Includes The Maintenance Services For Those Parts Of Mechanical And Electrotechnical/electronic Systems For Which The Maintenance Has An Impact On Safety And Functionality, With The Aim Of A Uniform Limitation Period For Buildings. The So-called Inner Courtyard Of The Congress Hall (unbuilt Actual Congress Hall) Is Almost Completely Sealed. In Front Of The Enclosing Walls On The Courtyard Side At A Width Of Approx. 43m There Are (divided By Shrinkage Lanes And On Gravel Pillars) Approx. 1.6m Thick Massive Reinforced Concrete Foundation Slabs Of The Unbuilt Grandstands, Which Should Serve As The Support Of The Supplementary Building For Reasons Of Economy. The "hof" Has A Single Driveway Between The Two Front Buildings On The East Side. The Congress Hall Is Located In An Intensively Used Environment With Sometimes Very Large Numbers Of People (zenzenteich Park, Nuremberg Folk Festivals Immediately To The West In Front Of The Building, Documentation Center Nazi Party Rally Grounds In The Northern End Building Of The Building, Nuremberg Symphony Orchestra And Serenadenhof In The Southern End Building Of The Building, Klassik Open Air In The Luitpoldhain Opposite , Norisring Races At The Zeppelin Grandstand, Nuremberg Exhibition Center, Max Morlock Stadium, Arena Nuremberg Insurance, Etc.). The Congress Hall Is Surrounded To The North-east And South-east By A Lake (big Dozen Pond) Used For Leisure Activities. Access To The Construction Site Is Possible Via Bayernstrasse And Grosse Strasse. The "courtyard" Of The Congress Hall Can Be Seen From Above From The Roof Of The Existing Building (visitor Terrace). Value Is Placed On An Appropriate Design Of The Roof Of The Supplementary Building As A "fifth Facade" (all-round View). Appropriate Design And Structural Handling, In Particular With The Raw Brick-faced Enclosing Walls Of The "inner Courtyard" And With The Existing Architectural Interventions In The Northern Front Building For The Documentation Center Nazi Party Rally Grounds (including Significant Penetration Of The Front Building With The "glass Pole" By The Architect Günther Domenig). Placed..

Details: Acadia Parish Police Jury – Old Va Building 601 N. Parkerson, Crowley, La 70526 Request For Qualifications (rfq) For Engineering And/or Architectural Services For Disaster Damages To Impacted Facilities And Infrastructure Acadia Parish Police Jury 505 Ne Court Circle Crowley, Louisiana 70526 337-788-8800 Date: January 27, 2024 Rfq#2023-011 Pursuant To The Regulations Found At 2 Code Of Federal Regulations (“c.f.r.”) Part 200 Et Seq, In Addition To The Statutory Authority, Regulatory Requirements, And Programmatic Guidance Governing The Federal Emergency Management Agency’s (“fema”) Disaster Recovery Programs, The Acadia Parish Police Jury Requests Qualified Firms To Submit Their Qualifications To Complete The Scope Of Work As Described In This Solicitation. Instruction To Proposers Notice Rfq-2023-011 To Provide Request For Qualifications (rfq) For Engineering And/or Architectural Services For Disaster Damages To Impacted Facilities And Infrastructure. The Information Provided In The Statement Of Work Is To Be Used Only For The Purposes Of Preparing A Proposal For Qualifications. It Is Further Expected That Each Bidder Will Read The Scope Of Work Thoroughly To Provide A Response That Meets All Requirements Outlined In The Scope Of Work. The Acadia Parish Police Jury Reserves The Right To Reject Any Or All Proposals For Qualifications Or Any Portion Thereof And To Accept The Submission Deemed Most Advantageous To Appj. The Information Contained Herein Is Believed To Be Accurate But Is Not To Be Considered In Any Way As A Warranty. Request For Additional Information Clarifying The Scope Of Work Should Be Directed In Writing To Robert Campbell, Rcampbell@rostan.com. B.statement Of Purpose The Primary Purpose Of This Request For Qualifications Is To Procure Qualified Engineering And/or Architectural Consultants Or Multidisciplinary Teams To Assist In The Assessment Of Damages To Develop Construction Plans, Specifications, Cost Estimates, And Perform Other Related Services For Various Projects That May Be Funded Through The Federal Emergency Management Agency (fema)’s Public Assistance Grant Program And/or The U.s. Department Of Housing And Community Development Block Grant Disaster Recovery Program. These Consulting Services Shall Be Performed In Accordance With All Local, State, And Federal Laws, Regulations, And Executive Orders Applicable To These Grant Programs. C.scope Of Work The Acadia Parish Police Jury (appj) Seeks To Obtain Proposals From Qualified Engineers And Architects Or Multi-disciplinary Teams To Assist In The Assessment Of Damages To Public Facilities And Infrastructure Caused By Hurricane Laura; Recommend Actions For Repair, Upgrade, Or Mitigation; Prepare Exhibits And Other Documents; Develop Construction Plans, Specifications, Cost Estimates, Mitigation Actions, Bid And Construction Documents; Construction Management; And Perform Other Related Services, For Various Projects That May Be Funded Through The Federal Emergency Management Agency (fema)’s Public Assistance Grant Program And/or The U.s. Department Of Housing And Urban Development (hud)’s Community Development Block Grant Disaster Recovery Program. The Selected Consultant(s) Must Have Knowledge Of And Provide All Services In Full Compliance With All Local, State, And Federal Laws, Regulations, And Executive Orders Applicable To These Grant Programs. Scope Of Architectural And Engineering Services: Preliminary Design Phase:a. Site Evaluation: Conduct A Site Assessment To Evaluate The Suitability Of The Existing Building For Renovation.b. Programming: Define The Space Requirements Of Parish Officials, Including Office Layouts And Common Areas.c. Conceptual Design: Develop Preliminary Design Concepts That Meet The Project Objectives Cost Estimation Provide Preliminary Cost Estimates For The Renovation Project. Design Development Phase: A. Architectural Design: Develop Detailed Architectural Plans, Including Floor Plans, Elevations, And Building Sections.b. Structural Engineering: Assess The Structural Integrity Of The Existing Building And Design Structural Modifications As Necessary. C. Mechanical, Electrical, And Plumbing (mep) Engineering: Design Mep Systems For The Building, Including Hvac, Electrical, And Plumbing. D. Fire And Life Safety: Ensure Compliance With Fire And Life Safety Codes, Including The Installation Of Necessary Systems. E. Accessibility: Design And Implement Accessibility Features To Meet Ada Requirements. Permitting And Regulatory Compliance:a. Prepare And Submit Permit Applications To Relevant Authorities. B. Coordinate With Local Building Officials To Obtain Necessary Approvals And Permits. C. Ensure Compliance With Federal Grant Requirements And Reporting. Construction Documentation Phase:a. Develop Detailed Construction Drawings And Specifications For Bidding And Construction. B. Assist In The Selection Of Contractors Through The Federal Grant's Procurement Process. Construction Phase: A. Construction Administration: Provide On-site Inspections And Monitoring To Ensure The Work Is Executed In Accordance With The Plans And Specifications. Respond To Requests For Information (rfis) And Change Orders As Needed. B. Quality Assurance And Quality Control (qa/qc): Oversee Quality Control Processes During Construction To Ensure Compliance With Design And Code Requirements. Post-construction Phase:a. Final Inspection: Conduct A Final Inspection To Verify That The Renovated Building Complies With All Relevant Codes And Regulations.b. Project Closeout: Assist In The Closeout Process, Including Final Inspections, Commissioning, And Obtaining The Certificate Of Occupancy. C. Provide As-built Drawings And Operation Manuals To The Client. Deliverables: The Following Deliverables Will Be Provided To The Client Upon Project Completion: Final Architectural And Engineering Drawings And Specifications Inspection Reports And Compliance Documentation As-built Drawings An Assigned Project Manager Will Serve As Engagement Leader And Will Coordinate The Tasks Outlined Above, Taking Direction From Owner's Designee. Other Consulting Staff (subconsultants) Will Provide Support Or Technical Services As Required For Implementation And Accounting Of Emergency Protective Measures Or Permanent Work. When Authorized, This Work Will Include The Assessment And Project Development For The Acadia Parish “old Va” Building. Project Development Will Also Include All Permitting, Coordination With Outside Agencies, And Any Other Items Necessary To Develop The Project In Compliance With Funding Source Requirements Successfully. The Appj May Use This Rfq To Enter One Or More Contracts, Each Comprising One Or More Partial Scopes Of Work, Projects, Or Stages Of Work. No Work May Commence, And No Cost May Be Incurred On Any Scope Of Work, Project, Or Work Stage Without Prior Written Authorization To Proceed. Acadia Parish - Old Va Building 601 N. Parkerson, Crowley, La 70526 The Executed Contract Will Meet All Rules For Federal Grants, As Provided For In Title 44 Code Of Federal Regulations And 2cfr 200.317 Through 200.326 And Appendix Ii D.timetable Last Day For Requests For Written Clarification Will Be February 14, 2024 At 10:00am. Central Standard Time. Proposals Will Be Accepted By Acadia Parish Police Jury. No Later Than February 27, 2024, At 10:00 Am. Central Standard Time. E.submission Of Proposals Of Qualifications All Interested Parties Shall Submit One (1) Hard Copy And One (1) Electronic Copy Of The Proposals Of Qualifications To Samantha Hickman, Purchaseagent@appj.org, No Later Than February 27, 2024, At 10:00 Am. Central Standard Time. Copies Can Also Be Dropped Off At The Acadia Parish Police Jury Administrative Office At 505 Ne Court Circle, Crowley, Louisiana 70526 Or Mailed To Acadia Parish Police Jury, Attn Samantha Hickman, Po Box A, Crowley La 70527. F.consideration Of Proposals This Rfq Does Not Commit The Acadia Parish Police Jury To The Award Of A Contract Nor Pay For Any Cost Incurred In The Preparation And Submission Of The Proposal Of Qualifications In Anticipation Of A Contract. The Acadia Parish Police Jury Reserves The Right To Reject Any Or All Proposals Of Qualifications And To Disregard Any Informality And/or Irregularity In The Quotation When, In Its Opinion, The Best Interest Of Acadia Parish Police Jury Will Be Served By Such Action. Proposals Failing To Provide Some Of The Items In The Statement Of Work Shall Not Be Rejected Per Se, But Any Deviations From The Scope Must Be Clearly Noted. G.acceptance Of Qualifications The Acadia Parish Police Jury Will Notify Proposers In Writing Of Acceptance Of One Or More Of The Proposals Of Qualifications And Rate Schedules. Failure To Provide Any Supplementary Documentation To Comply With The Respondent’s Submission May Be Grounds For Disqualification. H.contents Of Rfq Response Submittal The Following Is A List Of Information To Be Included In The Submittal Response: Executive Summary Name, Address, Email And Telephone Numbers. Qualifications Statement – Type Of Service(s) For Which Individual/firm Is Qualified. Table Of Contents - Organized In The Order Cited In The Format Contained Herein. Proposer Qualifications And Experience - History And Background Of Proposer, Financial Strength, Capacity, And Stability, With Related Services To Entities: Names/addresses Of Principals Of Firm. Resumes Of Key Personnel With Relevant Experience. Corporate Resolution Copy Of Valid Licenses Insurance Certifications Company Experience [“past Projects”] With A/e Design Projects Related To Federal Funding - (3) Similar Projects Undertaken Within The Last Five (5) Years Similar In Scope. Past Projects – Overview Of 5 Projects, Similar In Type, That Demonstrate Ability To Perform. References - Must Include Name, Entity Name, Telephone Number, & Email Address. Please Provide Three (3) References From Similar Projects Completed In The Last Three Years. I.qualifications The Following General Criteria In Combination With The Score Card (attached As “exhibit A”) Will Be Used In Evaluating The Qualifications Statements For Contractor Selection: Capability To Perform All Or Most Of The Services Required For The Project Recent Experience With Similar Or Other Projects Comparable To The Proposed Project. Reputation For Personal And Professional Integrity And Competence. Professional Background And Caliber Of Key Personnel. Capability To Meet Schedules And Deadlines. Qualifications And Experience Of The A/e Firm. Quality Of Projects Previously Undertaken. Degree Of Interest Shown In Undertaking This Project J.selection Process The Contract For This Project Will Be Awarded Through A Qualifications-based Selection Process. All Accepted Proposals Of Qualifications Will Be Reviewed By The Selection Committee. The Selected Firm (or Firms) Will Then Be Presented To The Acadia Parish Police Jury To Enter A Contract For This Project. Pricing For All Work Requested Through An Executed Contract Will Be Negotiated With The Firm Or Firms Selected Prior To Execution Of Subsequent Task Orders With A Not To Exceed Amount Stated. The Selection Process Shall Be As Follows: A Committee Of No More Than Three Acadia Parish Police Jury Representatives Will Review All Conforming Proposals Received Prior To The Deadline. The Contents Of All Proposals Will Be Reviewed Based On The Qualifications Identified In Section I And Will Be Scored Based On The Point Allocation Contained With The Police Jury’s Scorecard, Attached Hereto As Exhibit A. Each Of The Selection Factors Within Exhibit A Will Be Assigned A Value Based On The Total Available Points For That Factor. The Scores Of All Three Committee Members Will Be Averaged On A Final Score Card To Assign A Final Ranking. Any Ties Will Be Judged Based On The “references” Selection Factor, With The Highest Ranking Being Determined By The Highest Scoring Firm. Ties As To The Reference Scoring Factor Will Result In The Acadia Parish Police Jury Picking The Firm That Best Meets Its Needs. K.conflict Of Interest A Proposer Filing Its Qualifications Hereby Certifies That No Officer, Agent Or Employee Of The Acadia Parish Police Jury Has A Pecuniary Interest In This Proposal Of Qualifications And Rater Schedule Or Has Participated In Contract Negotiations On Behalf Of The Acadia Parish Police Jury; That The Proposal Of Qualifications And Rate Schedule Is Made In Good Faith Without Fraud, Collusion, Or Connection Of Any Kind With Any Other Bidder For The Same Request For Proposals Of Qualifications; The Bidder Is Competing Solely In Its Own Behalf Without Connection With, Or Obligation To, Any Undisclosed Person Or Firm. The Acadia Parish Police Jury Will Also Conduct Its Own, Internal Conflict Of Interest Review Prior To Entering Contract Negotiations With Any Firms. L.insurance Requirementprior To Commencing Work Hereunder, Vendor At His/its Expense Will Procure And Maintain The Following Minimum Insurance Naming The Acadia Parish Police Jury - As An Additional Insured For Both Ongoing And Completed Operations On Liability Coverage And Furnish Certificates As To Such On The Acadia Parish Police Jury’s Standard Certificate Form Or Standard Acord Form Certifying The Coverage As Follows: The Contractor Shall Maintain The Following Minimum Insurance Coverages For The Duration Of The Contract With Carriers Having A Current A.m. Best Rating A-: Vi Or Better. Such Limits Are Minimum Limits And Do Not Serve As A Cap On Contractor’s Liability Under This Contract. Commercial General Liability Insurance –the Vendor Shall Have And Maintain During The Life Of The Contract, Commercial General Liability Insurance In At Least The Following Limits: Limits $1,000,000 Each Occurrence $2,000,000 General Aggregate $1,000,000 Products/completed Operations Aggregate. $1,000,000 Personal Injury And Advertising Coverage Such Insurance Shall Name The Acadia Parish Police Jury As Additional Insured For Both Ongoing And Completed Operations By Use Of Endorsements Cg 20 10 And 20 37 Or Equivalent. Such Insurance Shall Provide A Waiver Of Subrogation In Favor Of The Acadia Parish Police Jury And Be Primary And Noncontributory With Any Coverage Maintained By Acadia Parish Police Jury. Business Automobile Liability Insurance The Vendor Shall Have And Maintain During The Life Of This Contract Comprehensive Automobile Liability, Including Owned, Non-owned And Hired Vehicle, Of Below Minimum Limits. Limits $1,000,000 Combined Single Limit Such Insurance Shall Name Acadia Parish Police Jury As Additional Insured, Contain A Waiver Of Subrogation In Favor Of The Acadia Parish Police Jury And Be Primary And Noncontributory With Any Insurance Coverage Maintained By The Acadia Parish Police Jury. Workers’ Compensation Insurance Limits- Statutory Benefits For The State In Which Operations Are Being Performed Employers’ Liability Insurance. Limits $1,000,000 Each Accident $1,000,000 Each Employee – Disease $1,000,000 Policy Limit – Disease Such Insurance Shall Contain A Waiver Of Subrogation In Favor Of The Acadia Parish Police Jury. To The Fullest Extent Permitted By Law, Contractor Agrees To Fully Defend, Indemnify And Hold Harmless Owner And Its Employees, Officers, And Agents, From And Against All Losses, Expenses, Liens, Claims, Demands, Damages, Or Causes Of Action Of Every Kind Of Character Whatsoever, For The Injury To Or Death Of Any Persons Or Damage To Property, Including Costs, Attorney’s Fees And Settlements, Arising Out Of Or In Any Way Related To Contractor’s Operations Under This Agreement. The Vendor Shall Not Cause Any Insurance To Be Cancelled Or Permit Any Insurance To Lapse. All Insurance Policies Shall Contain A Clause To The Effect That The Acadia Parish Police Jury Shall Receive By Written Notice As Evidenced By Return Receipt Of Registered Or Certified Letter A Ten (10) Day Notice Of Non-payment Of Premiums And Notice On Cancellation Or Non-renewal On The Policy In Accordance With Policy Provisions. In All Instances, Vendor Must Procure Insurance Naming The Acadia Parish Police Jury As An Additional Insured For Ongoing And Completed Operations On The General And Auto Liability Coverage And Include A Waiver Of Subrogation And Be Primary And Noncontributory With Any Insurance Maintained By The “appj”.note To Proposers: Submit Evidence Of These Insurance Requirements With All Required Information Set Forth In The Solicitation Documents As Your Proposal. Retain The Complete Set Of Specifications And Contract Documents And A Copy Of The Insurance Forms For Your Files. Requirements For Corporation Articles Of Incorporation Certificate Of Corporate Resolution Certificate Of Good Standing These Will Be Required Prior To The Execution Of Contract. N.required Clauses / Anti-lobbying This Procurement And Any Contracts Entered As A Result Must Be Fully Compliant With The Uniform Administrative Requirements, Cost Principles, And Audit Requirements Found In 2 Code Of Federal Regulations (“cfr”) Part 200 Et Seq. In Particular, The Contract Clauses Included In This Solicitation As “exhibit B” Will Be Incorporated Into Any Agreement Reached With Any Firm Selected For Negotiation. Additionally, As Part Of The Proposal, Contractor Will Also Execute An Anti-lobbying Certification As “exhibit C”. O.suspension & Debarrment The Services Sought Through This Procurement Are Subject To The Debarment And Suspension Regulations Implementing Executive Order 12549, Debarment And Suspension (1986) And Executive Order 12689, Debarment And Suspension (1989) At 2 C.f.r. Part 180 And The Department Of Homeland Security’s Regulations At 2 C.f.r. Part 3000 (non-procurement Debarment And Suspension). Prior To Execution Of Any Contracts Resulting From This Procurement, All Contractors Any Identified Sub-contractors Must Provide Satisfactory Evidence That They Are Neither Debarred Nor Suspended As Determined By The Federal Government’s System For Award Management. P.contract Durationthe Contract Resulting From This Rfq Will Have A Base Period Length Of 24 Months, Beginning On The Effective Date Of The Contract Or The Date Of The ’s Authorized Agent’s Signature, Whichever Is Later. The Acadia Parish Police Jury Reserves The Right To Renew The Contract For An Additional 1 Year Which, If Exercised, Would Result In A Total Contract Period Of Two (2) Years. Exhibit A Selection Committee Score Card Selection Factor Possible Points Total Points Awarded Capacity To Perform 30 Pts Past Projects 50 Pts References 20 Pts Total Score 100 Pts Exhibit B Required Clauses – Contract Provisions For Non-federal Entity Contracts Under Federal Awards Under 2 Cfr Part 200 Throughout The Performance Of Any Work Under This Agreement, The Contractor Agrees To Abide By The Following Clauses And Requirements: Equal Employment Opportunity. During The Performance Of This Agreement, The Contractor Agrees As Follows: Contractor Will Not Discriminate Against Any Employee Or Applicant For Employment Because Of Race, Color, Religion, Sex, Or National Origin. Contractor Will Take Affirmative Action To Ensure That Applicants Are Employed, And That Employees Are Treated During Employment Without Regard To Their Race, Color, Religion, Sex, Or National Origin. Such Action Shall Include, But Not Be Limited To The Following: Employment, Upgrading, Demotion, Or Transfer; Recruitment Or Recruitment Advertising; Layoff Or Termination; Rates Of Pay Or Other Forms Of Compensation; And Selection For Training, Including Apprenticeship. Contractor Agrees To Post In Conspicuous Places, Available To Employees And Applicants For Employment, Notices To Be Provided Setting Forth The Provisions Of This Nondiscrimination Clause. Contractor Will, In All Solicitations Or Advertisements For Employees Placed By Or On Behalf Of The Contractor, State That All Qualified Applicants Will Receive Considerations For Employment Without Regard To Race, Color, Religion, Sex, Or National Origin. Contractor Will Send To Each Labor Union Or Representative Of Workers With Which He Has A Collective Bargaining Agreement Or Other Contract Or Understanding, A Notice To Be Provided Advising The Said Labor Union Or Workers' Representatives Of Contractor's Commitments Under This Section And Shall Post Copies Of The Notice In Conspicuous Places Available To Employees And Applicants For Employment. Contractor Will Comply With All Provisions Of Executive Order 11246 Of September 24, 1965, And Of The Rules, Regulations, And Relevant Orders Of The Secretary Of Labor. Contractor Will Furnish All Information And Reports Required By Executive Order 11246 Of September 24, 1965, And By Rules, Regulations, And Orders Of The Secretary Of Labor, Or Pursuant Thereto, And Will Permit Access To His Books, Records, And Accounts By The Administering Agency And The Secretary Of Labor For Purposes Of Investigation To Ascertain Compliance With Such Rules, Regulations, And Orders. In The Event Of Contractor's Noncompliance With The Nondiscrimination Clauses Of This Contract Or With Any Of The Said Rules, Regulations, Or Orders, This Agreement May Be Canceled, Terminated, Or Suspended In Whole Or In Part And The Contractor May Be Declared Ineligible For Further Government Contracts Or Federally Assisted Construction Contracts In Accordance With Procedures Authorized In Executive Order 11246 Of September 24, 1965, And Such Other Sanctions As May Be Imposed And Remedies Invoked As Provided In Executive Order 11246 Of September 24, 1965, Or By Rule, Regulation, Or Order Of The Secretary Of Labor, Or As Otherwise Provided By Law. The Contractor Will Include The Portion Of The Sentence Immediately Preceding Paragraph (a) And The Provisions Of Paragraphs (a) Through (g) In Every Subcontract Or Purchase Order Unless Exempted By Rules, Regulations, Or Orders Of The Secretary Of Labor Issued Pursuant To Section 204 Of Executive Order 11246 Of September 24, 1965, So That Such Provisions Will Be Binding Upon Each Subcontractor Or Vendor. The Contractor Will Take Such Action With Respect To Any Subcontract Or Purchase Order As The Administering Agency May Direct As A Means Of Enforcing Such Provisions, Including Sanctions For Noncompliance: Provided, However, That In The Event That Contractor Becomes Involved In, Or Is Threatened With, Litigation With A Subcontractor Or Vendor As A Result Of Such Direction By The Administering Agency The Contractor May Request The United States To Enter Into Such Litigation To Protect The Interests Of The United States. Compliance With The Davis-bacon Act And The Copeland “anti-kickback” Act. As Required By Federal Program Legislation: Contractor Agrees That It Shall Comply With The Davis-bacon Act (40 Usc 3141-3144 And 3146-3148) As Supplemented By The Department Of Labor Regulations (29 Cfr Part 5, "labor Standards Provisions Applicable To Contracts Covering Federally Financed And Assisted Construction"). In Accordance With The Statute, Contractor Is Required To Pay Wages To Laborers And Mechanics At A Rate Not Less Than The Prevailing Wages Specified In A Wage Determination Made By The Secretary Of Labor. In Addition, Contractor Shall Pay Wages Not Less Than Once A Week. Contractor Agrees That, For Any Task Order To Which This Requirement Applies, The Contract Is Conditioned Upon Contractor's Acceptance Of The Wage Determination. Contractor Agrees That It Shall Comply With The Copeland "anti-kickback" Act (40 Usc 3145), As Supplemented By The Department Of Labor Regulations (29 Cfr Part 3, "contractors And Subcontractors On Public Building Or Public Work Financed In Whole Or In Part By Loans Or Grants From The United States") And Are Incorporated By Reference Into This Agreement. Contactor. The Contractor Shall Comply With 18 U.s.c. § 874, 40 U.s.c. § 3145, And The Requirements Of 29 C.f.r. Pt. 3 As May Be Applicable, Which Are Incorporated By Reference Into This Agreement. Subcontracts. The Contractor Or Subcontractor Shall Insert In Any Subcontracts The Clause Above And Such Other Clauses As The Fema May By Appropriate Instructions Require, And Also A Clause Requiring The Subcontractors To Include These Clauses In Any Lower Tier Subcontracts. The Prime Contractor Shall Be Responsible For The Compliance By Any Subcontractor Or Lower Tier Subcontractor With All Of These Contract Clauses. Breach. A Breach Of The Contract Clauses Above May Be Grounds For Termination Of The Contract, And For Debarment As A Contractor And Subcontractor As Provided In 29 C.f.r. § 5.12. Compliance With The Contract Work Hours And Safety Standards Act. Overtime Requirements. The Contractor Or Subcontractor Contracting For Any Part Of The Contract Work Which May Require Or Involve The Employment Of Laborers Or Mechanics Shall Not Require Nor Permit Any Such Laborer Or Mechanic In Any Workweek In Which He Or She Is Employed On Such Work To Work In Excess Of Forty Hours In Such Workweek Unless Such Laborer Or Mechanic Receives Compensation At A Rate Not Less Than One And One-half Times The Basic Rate Of Pay For All Hours Worked In Excess Of Forty Hours In Such Workweek. Violation; Liability For Unpaid Wages; Liquidated Damages. In The Event Of Any Violation Of The Clause Set Forth In Paragraph (1) Of This Section The Contractor And Any Subcontractor Responsible Therefor Shall Be Liable For The Unpaid Wages. In Addition, The Contractor And Subcontractor Shall Be Liable To The United States (in The Case Of Work Done Under Contract For The District Of Columbia Or A Territory, To Such District Or To Such Territory), For Liquidated Damages. Such Liquidated Damages Shall Be Computed With Respect To Each Individual Laborer Or Mechanic, Including Watchmen And Guards, Employed In Violation Of The Clause Set Forth In Paragraph (a) Of This Section, In The Sum Of $10 For Each Calendar Day On Which Such Individual Was Required Or Permitted To Work In Excess Of The Standard Workweek Of Forty Hours Without Payment Of The Overtime Wages Required By The Clause Set Forth In Paragraph (a) Of This Section. Withholding For Unpaid Wages And Liquidated Damages. The Client Shall Upon Its Own Action Or Upon Written Request Of An Authorized Representative Of The Department Of Labor Withhold Or Cause To Be Withheld, From Any Moneys Payable On Account Of Work Performed By The Contractor Or Subcontractor Under Any Such Contract Or Any Other Federal Contract With The Same Prime Contractor, Or Any Other Federally-assisted Contract Subject To The Contract Work Hours And Safety Standards Act, Which Is Held By The Same Prime Contractor, Such Sums As May Be Determined To Be Necessary To Satisfy Any Liabilities Of Such Contractor Or Subcontractor For Unpaid Wages And Liquidated Damages As Provided In The Clause Set Forth In Paragraph (b) Of This Section. Subcontracts. The Contractor Or Subcontractor Shall Insert In Any Subcontracts The Clauses Set Forth In Paragraph (a) Through (d) Of This Section And A Clause Requiring The Subcontractors To Include These Clauses In Any Lower Tier Subcontracts. The Prime Contractor Shall Be Responsible For Compliance By Any Subcontractor Or Lower Tier Subcontractor With The Clauses Set Forth In Paragraphs (a) Through (d) Of This Section. Rights To Inventions Made Under A Contract Or Agreement. As Required By Federal Program Legislation, Contractor Agrees To Comply With The Requirements Of 37 C.f.r. Part 401 (rights To Inventions Made By Nonprofit Organizations And Small Business Firms Under Government Grants, Contracts And Cooperative Agreements), And Any Implementing Regulations Issued By Fema. Clean Air Act And Federal Water Pollution Control Act. As Required By Federal Program Legislation: Contractor Agrees To Comply With The Following Federal Requirements: Clean Air Act. The Contractor Agrees To Comply With All Applicable Standards, Orders Or Regulations Issued Pursuant To The Clean Air Act, As Amended, 42 U.s.c. (2) The Contractor Agrees To Report Each Violation To The Client] And Understands And Agrees That The Client Will, In Turn, Report Each Violation As Required To Assure Notification To The State Of Louisiana, Federal Emergency Management Agency, And The Appropriate Environmental Protection Agency Regional Office. The Contractor Agrees To Include These Requirements In Each Subcontract Exceeding $150,000 Financed In Whole Or In Part With Federal Assistance Provided By Fema. Federal Water Pollution Control Act The Contractor Agrees To Comply With All Applicable Standards, Orders Or Regulations Issued Pursuant To The Federal Water Pollution Control Act, As Amended, 33 U.s.c. 1251 Et Seq. The Contractor Agrees To Report Each Violation To The Client And Understands And Agrees That The Client Will, In Turn, Report Each Violation As Required To Assure Notification To The State Of Louisiana, Federal Emergency Management Agency, And The Appropriate Environmental Protection Agency Regional Office. The Contractor Agrees To Include These Requirements In Each Subcontract Exceeding $150,000 Financed In Whole Or In Part With Federal Assistance Provided By Fema. Suspension And Debarment. This Contract Is A Covered Transaction For Purposes Of 2 C.f.r. Pt. 180 And 2 C.f.r. Pt. 3000. As Such The Contractor Is Required, And Will, Verify That Neither Contractor, Its Principals (defined At 2 C.f.r. § 180.995), Nor Its Affiliates (defined At 2 C.f.r. § 180.905) Are Excluded (defined At 2 C.f.r. § 180.940) Or Disqualified (defined At 2 C.f.r. § 180.935). The Contractor Will Comply With 2 C.f.r. Pt. 180, Subpart C And 2 C.f.r. Pt. 3000, Subpart C And Must Include A Requirement To Comply With These Regulations In Any Lower Tier Covered Transaction It Enters. Contractor’s Certification Is A Material Representation Of Fact Relied Upon By The Client. If It Is Later Determined That The Contractor Did Not Comply With 2 C.f.r. Pt. 180, Subpart C And 2 C.f.r. Pt. 3000, Subpart C, In Addition To Remedies Available To State Of Louisiana, The Federal Government May Pursue Available Remedies, Including But Not Limited To Suspension And/or Debarment. The Contractor Agrees To Comply With The Requirements Of 2 C.f.r. Pt. 180, Subpart C And 2 C.f.r. Pt. 3000, Subpart C Throughout The Period This Agreement. The Contractor Further Agrees To Include A Provision Requiring Such Compliance In Its Lower-tier Covered Transactions. Byrd Anti-lobbying Amendment, 31 U.s.c. § 1352 (as Amended) The Contractor Certifies To The Client That It Has Not And Will Not Use Federal Appropriated Funds To Pay Any Person Or Organization For Influencing Or Attempting To Influence An Officer Or Employee Of Any Agency, A Member Of Congress, Officer Or Employee Of Congress, Or An Employee Of A Member Of Congress In Connection With Obtaining Any Federal Contract, Grant, Or Any Other Award Covered By 31 U.s.c. § 1352. The Required Certification Is Provided As An Addendum To This Agreement. Contractor Will Also Ensure That Each Tier Of Subcontractor(s) Shall Also Disclose Any Lobbying With Non-federal Funds That Takes Place In Connection With Obtaining Any Federal Award. Such Disclosures Will Be Forwarded From Tier-to-tier Up To The Client. Procurement Of Recovered Materials. As Required By Federal Program Legislation, Contractor Agrees To The Following: In The Performance Of This Contract, The Contractor Shall Make Maximum Use Of Products Containing Recovered Materials That Are Epa-designated Items Unless The Product Cannot Be Acquired: Competitively Within A Timeframe Providing For Compliance With The Contract Performance Schedule; Meeting Contract Performance Requirements; Or At A Reasonable Price. Information About This Requirement, Along With The List Of Epa-designate Items, Is Available At Epa’s Comprehensive Procurement Guidelines Web Site, Https://www.epa.gov/smm/comprehensive-procurement-guideline-cpg-program. Dhs Seals, Logos, And Flags. The Contractor Shall Not Use The Dhs Seal(s), Logos, Crests, Or Reproductions Of Flags Or Likenesses Of Dhs Agency Officials Without Specific Fema Pre-approval. Compliance With Federal Law, Regulations, And Executive Orders. The Contractor Acknowledges That Fema Financial Assistance Will Be Used To Fund The Contract Only. The Contractor Will Comply Will All Applicable Federal Law, Regulations, Executive Orders, Fema Policies, Procedures, And Directives. No Obligation By Federal Government. “the Federal Government Is Not A Party To This Contract And Is Not Subject To Any Obligations Or Liabilities To The Non-federal Entity, Contractor, Or Any Other Party Pertaining To Any Matter Resulting From The Contract. Program Fraud And False Or Fraudulent Statements Or Related Acts. The Contractor Acknowledges That 31 U.s.c. Chap. 38 (administrative Remedies For False Claims And Statements) Applies To The Contractor Actions Pertaining To This Agreement. Exhibit C Certification Regarding Lobbying The Undersigned Certifies, To The Best Of His Or Her Knowledge, That: 1. No Federal Appropriated Funds Have Been Paid Or Will Be Paid, By Or On Behalf Of The Undersigned, To Any Person For Influencing Or Attempting To Influence An Officer Or Employee Of An Agency, A Member Of Congress, An Officer Or Employee Of Congress, Or An Employee Of A Member Of Congress In Connection With The Awarding Of Any Federal Contract, The Making Of Any Federal Grant, The Making Of Any Federal Loan, The Entering Into Of Any Cooperative Agreement, And The Extension, Continuation, Renewal, Amendment, Or Modification Of Any Federal Contract, Grant, Loan, Or Cooperative Agreement. 2. If Any Funds Other Than Federal Appropriated Funds Have Been Paid Or Will Be Paid To Any Person For Influencing Or Attempting To Influence An Officer Or Employee Of Any Agency, A Member Of Congress, An Officer Or Employee Of Congress, Or An Employee Of A Member Of Congress In Connection With This Federal Contract, Grant, Loan, Or Cooperative Agreement, The Undersigned Shall Complete And Submit Standard Form-lll, “disclosure Form To Report Lobbying,” In Accordance With Its Instructions. 3. The Undersigned Shall Require That The Language Of This Certification Be Included In The Award Documents For All Subawards At All Tiers (including Subcontracts, Subgrants, And Contracts Under Grants, Loans, And Cooperative Agreements) And That All Subrecipients Shall Certify And Disclose Accordingly. This Certification Is A Material Representation Of Fact Upon Which Reliance Was Placed When This Transaction Was Made Or Entered Into. Submission Of This Certification Is A Prerequisite For Making Or Entering Into This Transaction Imposed By 31, U.s.c. § 1352 (as Amended By The Lobbying Disclosure Act Of 1995). Any Person Who Fails To File The Required Certification Shall Be Subject To A Civil Penalty Of Not Less Than $10,000 And Not More Than $100,000 For Each Such Failure. The Contractor, _____________, Certifies Or Affirms The Truthfulness And Accuracy Of Each Statement Of Its Certification And Disclosure, If Any. In Addition, The Contractor Understands And Agrees That The Provisions Of 31 U.s.c. § 3801 Et Seq., Apply To This Certification And Disclosure, If Any. ______________________________________________ Signature Of Contractor’s Authorized Representative ______________________________________________ Name And Title Of Contractor’s Authorized Representative ______________ Date Exhibit D: Certification Statement The Undersigned Hereby Acknowledges She/he Has Read And Understands All Requirements And Specifications Of The Request For Qualifications (rfq), Including Attachments. Official Contact. The Police Jury Requests That The Proposer Designate One Person To Receive All Documents And The Method In Which The Documents Are Best Delivered. The Proposer Should Identify The Contact Name And Fill In The Information Below: (print Clearly) Official Contact Name: E-mail Address: Facsimile Number With Area Code: ( ) Us Mail Address: Proposer Shall Certify That The Above Information Is True And Shall Grant Permission To The State Or Agencies To Contact The Above-named Person Or Otherwise Verify The Information Provided. By Its Submission Of This Proposal And Authorized Signature Below, Proposer Shall Certify That: The Information Contained In Its Response To This Rfp Is Accurate; Proposer Shall Comply With Each Of The Mandatory Requirements Listed In The Rfp And Will Meet Or Exceed The Functional And Technical Requirements Specified Therein; Proposer Shall Accept The Procedures, Evaluation Criteria, Mandatory Contract Terms And Conditions, And All Other Administrative Requirements Set Forth In This Rfp. Proposer's Quote Shall Be Valid For At Least 90 Calendar Days From The Date Of Proposal's Signature Below; Proposer Understands That If Selected As The Successful Proposer, He/she Will Have Seven(7) Business Days From The Date Of Delivery Of Final Contract In Which To Complete Contract Negotiations, If Any, And Execute The Final Contract Document. Proposer Certifies That The Proposer Company, Any Subcontractors, And/or Principals Are Not Suspended, Debarred, Or Otherwise Excluded From Or Ineligible For Participation In Federal Assistance Programs Or Activities. Signature Of Proposer Or Authorized Representative: Printed Name: Title: Date:

Tender Id: 2303127 - RFP-Architect | Rjh Renal Reverse Osmosis System Replacement

Details: Description Philippine Bidding Documents (as Harmonized With Development Partners) Construction Of Swine Artificial Insemination Building At Art Center, Brgy. Nanga, Pototan, Iloilo Bid No. Agr-24-932-b Iloilo Provincial Government Sixth Edition Table Of Contents Glossary Of Terms, Abbreviations, And Acronyms 3 Section I. Invitation To Bid 5 Section Ii. Instructions To Bidders 7 1. Scope Of Bid 7 2. Funding Information 7 3. Bidding Requirements 7 4. Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices 7 5. Eligible Bidders 8 6. Origin Of Associated Goods 8 7. Subcontracts 8 8. Pre-bid Conference 8 9. Clarification And Amendment Of Bidding Documents 8 10. Documents Comprising The Bid: Eligibility And Technical Components 9 11. Documents Comprising The Bid: Financial Component 9 12. Alternative Bids 9 13. Bid Prices 10 14. Bid And Payment Currencies 10 15. Bid Security 10 16. Sealing And Marking Of Bids 10 17. Deadline For Submission Of Bids 10 18. Opening And Preliminary Examination Of Bids 11 19. Detailed Evaluation And Comparison Of Bids 11 20. Post Qualification 11 21. Signing Of The Contract 11 Section Iii. Bid Data Sheet 12 Section Iv. General Conditions Of Contract 14 1. Scope Of Contract 14 2. Sectional Completion Of Works 14 3. Possession Of Site 14 4. The Contractor’s Obligations 14 5. Performance Security 15 6. Site Investigation Reports 15 7. Warranty 15 8. Liability Of The Contractor 15 9. Termination For Other Causes 15 10. Dayworks 15 11. Program Of Work 16 12. Instructions, Inspections And Audits 16 13. Advance Payment 16 14. Progress Payments 16 15. Operating And Maintenance Manuals 16 Section V. Special Conditions Of Contract 17 Section Vi. Specifications 18 Section Vii. Drawings 23 Section Viii. Bill Of Quantities 28 Section Ix. Checklist Of Technical And Financial Documents 36 Glossary Of Terms, Abbreviations, And Acronyms Abc – Approved Budget For The Contract. Arcc – Allowable Range Of Contract Cost. Bac – Bids And Awards Committee. Bid – A Signed Offer Or Proposal To Undertake A Contract Submitted By A Bidder In Response To And In Consonance With The Requirements Of The Bidding Documents. Also Referred To As Proposal And Tender. (2016 Revised Irr, Section 5[c]) Bidder – Refers To A Contractor, Manufacturer, Supplier, Distributor And/or Consultant Who Submits A Bid In Response To The Requirements Of The Bidding Documents. (2016 Revised Irr, Section 5[d]) Bidding Documents – The Documents Issued By The Procuring Entity As The Bases For Bids, Furnishing All Information Necessary For A Prospective Bidder To Prepare A Bid For The Goods, Infrastructure Projects, And/or Consulting Services Required By The Procuring Entity. (2016 Revised Irr, Section 5[e]) Bir – Bureau Of Internal Revenue. Bsp – Bangko Sentral Ng Pilipinas. Cda – Cooperative Development Authority. Consulting Services – Refer To Services For Infrastructure Projects And Other Types Of Projects Or Activities Of The Gop Requiring Adequate External Technical And Professional Expertise That Are Beyond The Capability And/or Capacity Of The Gop To Undertake Such As, But Not Limited To: (i) Advisory And Review Services; (ii) Pre-investment Or Feasibility Studies; (iii) Design; (iv) Construction Supervision; (v) Management And Related Services; And (vi) Other Technical Services Or Special Studies. (2016 Revised Irr, Section 5[i]) Contract – Refers To The Agreement Entered Into Between The Procuring Entity And The Supplier Or Manufacturer Or Distributor Or Service Provider For Procurement Of Goods And Services; Contractor For Procurement Of Infrastructure Projects; Or Consultant Or Consulting Firm For Procurement Of Consulting Services; As The Case May Be, As Recorded In The Contract Form Signed By The Parties, Including All Attachments And Appendices Thereto And All Documents Incorporated By Reference Therein. Contractor – Is A Natural Or Juridical Entity Whose Proposal Was Accepted By The Procuring Entity And To Whom The Contract To Execute The Work Was Awarded. Contractor As Used In These Bidding Documents May Likewise Refer To A Supplier, Distributor, Manufacturer, Or Consultant. Cpi – Consumer Price Index. Dole – Department Of Labor And Employment. Dti – Department Of Trade And Industry. Foreign-funded Procurement Or Foreign-assisted Project – Refers To Procurement Whose Funding Source Is From A Foreign Government, Foreign Or International Financing Institution As Specified In The Treaty Or International Or Executive Agreement. (2016 Revised Irr, Section 5[b]). Gfi – Government Financial Institution. Gocc – Government-owned And/or –controlled Corporation. Goods – Refer To All Items, Supplies, Materials And General Support Services, Except Consulting Services And Infrastructure Projects, Which May Be Needed In The Transaction Of Public Businesses Or In The Pursuit Of Any Government Undertaking, Project Or Activity, Whether In The Nature Of Equipment, Furniture, Stationery, Materials For Construction, Or Personal Property Of Any Kind, Including Non-personal Or Contractual Services Such As The Repair And Maintenance Of Equipment And Furniture, As Well As Trucking, Hauling, Janitorial, Security, And Related Or Analogous Services, As Well As Procurement Of Materials And Supplies Provided By The Procuring Entity For Such Services. The Term “related” Or “analogous Services” Shall Include, But Is Not Limited To, Lease Or Purchase Of Office Space, Media Advertisements, Health Maintenance Services, And Other Services Essential To The Operation Of The Procuring Entity. (2016 Revised Irr, Section 5[r]) Gop – Government Of The Philippines. Infrastructure Projects – Include The Construction, Improvement, Rehabilitation, Demolition, Repair, Restoration Or Maintenance Of Roads And Bridges, Railways, Airports, Seaports, Communication Facilities, Civil Works Components Of Information Technology Projects, Irrigation, Flood Control And Drainage, Water Supply, Sanitation, Sewerage And Solid Waste Management Systems, Shore Protection, Energy/power And Electrification Facilities, National Buildings, School Buildings, Hospital Buildings, And Other Related Construction Projects Of The Government. Also Referred To As Civil Works Or Works. (2016 Revised Irr, Section 5[u]) Lgus – Local Government Units. Nfcc – Net Financial Contracting Capacity. Nga – National Government Agency. Pcab – Philippine Contractors Accreditation Board. Philgeps - Philippine Government Electronic Procurement System. Procurement Project – Refers To A Specific Or Identified Procurement Covering Goods, Infrastructure Project Or Consulting Services. A Procurement Project Shall Be Described, Detailed, And Scheduled In The Project Procurement Management Plan Prepared By The Agency Which Shall Be Consolidated In The Procuring Entity's Annual Procurement Plan. (gppb Circular No. 06-2019 Dated 17 July 2019) Psa – Philippine Statistics Authority. Sec – Securities And Exchange Commission. Slcc – Single Largest Completed Contract. Un – United Nations. Republic Of The Philippines Iloilo Provincial Government Section I. Invitation To Bid For The Construction Of Swine Artificial Insemination Building At Art Center, Brgy. Nanga, Pototan, Iloilo Bid No. Agr-24-932-b 1. The Iloilo Provincial Government, Through The 20% Nta-fy 2024 Intends To Apply The Sum Of Ten Million Pesos (p10,000,000.00) Being The Approved Budget For The Contract (abc) To Payments Under The Contract For Agr-24-932-b For The Construction Of Swine Artificial Insemination Building At Art Center, Brgy. Nanga, Pototan, Iloilo For The Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. 2. The Iloilo Provincial Government Now Invites Bids For The Above Procurement Project. Completion Of The Works Is Required One Hundred Fifty (150) Calendar Days. Bidders Should Have Completed A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii (instructions To Bidders). 3. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) No. 9184. 4. Interested Bidders May Obtain Further Information From The Bids And Awards Committee Secretariat, 5th Floor, New Iloilo Provincial Capitol, Bonifacio Drive, Iloilo City, Philippines And Inspect The Bidding Documents At The Address Given Below From 8:00am To 5:00pm. 5. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders On July 29, 2024 From Given Address And Website/s Below And Upon Payment Of The Applicable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb, In The Amount Of Ten Thousand Pesos (p10, 000.00). The Procuring Entity Shall Allow The Bidder To Present Its Proof Of Payment For The Fees In Person. 6. The Iloilo Provincial Government Will Hold A Pre-bid Conference On August 6, 2024, 9:00 A.m. At Bids And Awards Committee Secretariat, 5th Floor, New Iloilo Provincial Capitol, Bonifacio Drive, Iloilo City, Philippines, And/or Through Videoconferencing/webcasting Via Zoom Conference Which Shall Be Open To Prospective Bidders. The Default Meeting Id And Password Shall Be: Meeting Id: 4340851724 // Password: 0922 7. Bids Must Be Duly Received By The Bac Secretariat Through Manual Submission At The Office Address At Bids And Awards Committee Secretariat, 5th Floor, New Iloilo Provincial Capitol, Bonifacio Drive, Iloilo City On Or Before August 20, 2024, 9:00 A.m. Late Bids Shall Not Be Accepted. 8. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 16. 9. Bid Opening Shall Be On August 20, 2024, 9:00 A.m. At Bids And Awards Committee Secretariat, 5th Floor, New Iloilo Provincial Capitol, Bonifacio Drive, Iloilo City, Philippines. Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend The Activity. 10. The Iloilo Provincial Government Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Implementing Rules And Regulations (irr) Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 11. For Further Information, Please Refer To: Atty. Raemman M. Lagrada Head, Bac Secretariat 5f New Iloilo Provincial Capitol Bonifacio Drive, Iloilo City Tel. No. (33) 336-0736 Fax No. (33) 337-7731 Email: Ipg_bacs@yahoo.com 12. You May Visit The Following Websites: For Downloading Of Bidding Documents: Www.iloilo.gov.ph July 15, 2024 Atty. Dennis T. Ventilacion Bac Chairperson Section Ii. Instructions To Bidders 1. Scope Of Bid The Procuring Entity, Iloilo Provincial Government Invites Bids For The Construction Of Swine Artificial Insemination Building At Art Center, Brgy. Nanga, Pototan, Iloilo With Project Identification Number Agr-24-932-b. The Procurement Project (referred To Herein As “project”) Is For The Construction Of Works, As Described In Section Vi (specifications). 2. Funding Information 2.1. The Gop Through The Source Of Funding As Indicated Below For 2024 In The Amount Of Ten Million Pesos (p10,000,000.00) 2.2. The Source Of Funding Is: A. 20% Nta- Fy 2024 3. Bidding Requirements The Bidding For The Project Shall Be Governed By All The Provisions Of Ra No. 9184 And Its 2016 Revised Irr, Including Its Generic Procurement Manual And Associated Policies, Rules And Regulations As The Primary Source Thereof, While The Herein Clauses Shall Serve As The Secondary Source Thereof. Any Amendments Made To The Irr And Other Gppb Issuances Shall Be Applicable Only To The Ongoing Posting, Advertisement, Or Invitation To Bid By The Bac Through The Issuance Of A Supplemental Or Bid Bulletin. The Bidder, By The Act Of Submitting Its Bid, Shall Be Deemed To Have Inspected The Site, Determined The General Characteristics Of The Contracted Works And The Conditions For This Project, Such As The Location And The Nature Of The Work; (b) Climatic Conditions; (c) Transportation Facilities; (c) Nature And Condition Of The Terrain, Geological Conditions At The Site Communication Facilities, Requirements, Location And Availability Of Construction Aggregates And Other Materials, Labor, Water, Electric Power And Access Roads; And (d) Other Factors That May Affect The Cost, Duration And Execution Or Implementation Of The Contract, Project, Or Work And Examine All Instructions, Forms, Terms, And Project Requirements In The Bidding Documents. 4. Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices The Procuring Entity, As Well As The Bidders And Contractors, Shall Observe The Highest Standard Of Ethics During The Procurement And Execution Of The Contract. They Or Through An Agent Shall Not Engage In Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices Defined Under Annex “i” Of The 2016 Revised Irr Of Ra No. 9184 Or Other Integrity Violations In Competing For The Project. 5. Eligible Bidders 5.1. Only Bids Of Bidders Found To Be Legally, Technically, And Financially Capable Will Be Evaluated. 5.2. The Bidder Must Have An Experience Of Having Completed A Single Largest Completed Contract (slcc) That Is Similar To This Project, Equivalent To At Least Fifty Percent (50%) Of The Abc Adjusted, If Necessary, By The Bidder To Current Prices Using The Psa’s Cpi, Except Under Conditions Provided For In Section 23.4.2.4 Of The 2016 Revised Irr Of Ra No. 9184. A Contract Is Considered To Be “similar” To The Contract To Be Bid If It Has The Major Categories Of Work Stated In The Bds. 5.3. For Foreign-funded Procurement, The Procuring Entity And The Foreign Government/foreign Or International Financing Institution May Agree On Another Track Record Requirement, As Specified In The Bidding Document Prepared For This Purpose. 5.4. The Bidders Shall Comply With The Eligibility Criteria Under Section 23.4.2 Of The 2016 Irr Of Ra No. 9184. 6. Origin Of Associated Goods There Is No Restriction On The Origin Of Goods Other Than Those Prohibited By A Decision Of The Un Security Council Taken Under Chapter Vii Of The Charter Of The Un. 7. Subcontracts 7.1. The Bidder May Subcontract Portions Of The Project To The Extent Allowed By The Procuring Entity As Stated Herein, But In No Case More Than Fifty Percent (50%) Of The Project. The Procuring Entity Has Prescribed That: A. Subcontracting Is Not Allowed. 8. Pre-bid Conference The Procuring Entity Will Hold A Pre-bid Conference For This Project On The Specified Date And Time And Either At Its Physical Address At Bac Office, 5th Floor, New Iloilo Provincial Capitol, Iloilo City And/or Through Videoconferencing As Indicated In Paragraph 6 Of The Ib. 9. Clarification And Amendment Of Bidding Documents Prospective Bidders May Request For Clarification On And/or Interpretation Of Any Part Of The Bidding Documents. Such Requests Must Be In Writing And Received By The Procuring Entity, Either At Its Given Address Or Through Electronic Mail Indicated In The Ib, At Least Ten (10) Calendar Days Before The Deadline Set For The Submission And Receipt Of Bids. 10. Documents Comprising The Bid: Eligibility And Technical Components 10.1. The First Envelope Shall Contain The Eligibility And Technical Documents Of The Bid As Specified In Section Ix. Checklist Of Technical And Financial Documents. 10.2. If The Eligibility Requirements Or Statements, The Bids, And All Other Documents For Submission To The Bac Are In Foreign Language Other Than English, It Must Be Accompanied By A Translation In English, Which Shall Be Authenticated By The Appropriate Philippine Foreign Service Establishment, Post, Or The Equivalent Office Having Jurisdiction Over The Foreign Bidder’s Affairs In The Philippines. For Contracting Parties To The Apostille Convention, Only The Translated Documents Shall Be Authenticated Through An Apostille Pursuant To Gppb Resolution No. 13-2019 Dated 23 May 2019. The English Translation Shall Govern, For Purposes Of Interpretation Of The Bid. 10.3. In Joint Ventures, A Special Pcab License, And Registration For The Type And Cost Of The Contract For This Project, Shall Be Required. Any Additional Type Of Contractor License Or Permit Shall Be Indicated In The Bds. 10.4. A List Of Contractor’s Key Personnel (e.g., Project Manager, Project Engineers, Materials Engineers, And Foremen) Assigned To The Contract To Be Bid, With Their Complete Qualification And Experience Data Shall Be Provided. These Key Personnel Must Meet The Required Minimum Years Of Experience Set In The Bds. 10.5. A List Of Contractor’s Major Equipment Units, Which Are Owned, Leased, And/or Under Purchase Agreements, Supported By Proof Of Ownership, Certification Of Availability Of Equipment From The Equipment Lessor/vendor For The Duration Of The Project, As The Case May Be, Must Meet The Minimum Requirements For The Contract Set In The Bds. 11. Documents Comprising The Bid: Financial Component 11.1. The Second Bid Envelope Shall Contain The Financial Documents For The Bid As Specified In Section Ix. Checklist Of Technical And Financial Documents. 11.2. Any Bid Exceeding The Abc Indicated In Paragraph 1 Of The Ib Shall Not Be Accepted. 11.3. For Foreign-funded Procurement, A Ceiling May Be Applied To Bid Prices Provided The Conditions Are Met Under Section 31.2 Of The 2016 Revised Irr Of Ra No. 9184. 12. Alternative Bids Bidders Shall Submit Offers That Comply With The Requirements Of The Bidding Documents, Including The Basic Technical Design As Indicated In The Drawings And Specifications. Unless There Is A Value Engineering Clause In The Bds, Alternative Bids Shall Not Be Accepted. 13. Bid Prices All Bid Prices For The Given Scope Of Work In The Project As Awarded Shall Be Considered As Fixed Prices, And Therefore Not Subject To Price Escalation During Contract Implementation, Except Under Extraordinary Circumstances As Determined By The Neda And Approved By The Gppb Pursuant To The Revised Guidelines For Contract Price Escalation Guidelines. 14. Bid And Payment Currencies 14.1. Bid Prices May Be Quoted In The Local Currency Or Tradeable Currency Accepted By The Bsp At The Discretion Of The Bidder. However, For Purposes Of Bid Evaluation, Bids Denominated In Foreign Currencies Shall Be Converted To Philippine Currency Based On The Exchange Rate As Published In The Bsp Reference Rate Bulletin On The Day Of The Bid Opening. 14.2. Payment Of The Contract Price Shall Be Made In: A. Philippine Pesos. 15. Bid Security 15.1. The Bidder Shall Submit A Bid Securing Declaration Or Any Form Of Bid Security In The Amount Indicated In The Bds, Which Shall Be Not Less Than The Percentage Of The Abc In Accordance With The Schedule In The Bds. 15.2. The Bid And Bid Security Shall Be Valid Until December 18, 2024. Any Bid Not Accompanied By An Acceptable Bid Security Shall Be Rejected By The Procuring Entity As Non-responsive. 16. Sealing And Marking Of Bids Each Bidder Shall Submit One Copy Of The First And Second Components Of Its Bid. The Procuring Entity May Request Additional Hard Copies And/or Electronic Copies Of The Bid. However, Failure Of The Bidders To Comply With The Said Request Shall Not Be A Ground For Disqualification. If The Procuring Entity Allows The Submission Of Bids Through Online Submission To The Given Website Or Any Other Electronic Means, The Bidder Shall Submit An Electronic Copy Of Its Bid, Which Must Be Digitally Signed. An Electronic Copy That Cannot Be Opened Or Is Corrupted Shall Be Considered Non-responsive And, Thus, Automatically Disqualified. 17. Deadline For Submission Of Bids The Bidders Shall Submit On The Specified Date And Time And Either At Its Physical Address Or Through Online Submission As Indicated In Paragraph 7 Of The Ib. 18. Opening And Preliminary Examination Of Bids 18.1. The Bac Shall Open The Bids In Public At The Time, On The Date, And At The Place Specified In Paragraph 9 Of The Ib. The Bidders’ Representatives Who Are Present Shall Sign A Register Evidencing Their Attendance. In Case Videoconferencing, Webcasting Or Other Similar Technologies Will Be Used, Attendance Of Participants Shall Likewise Be Recorded By The Bac Secretariat. In Case The Bids Cannot Be Opened As Scheduled Due To Justifiable Reasons, The Rescheduling Requirements Under Section 29 Of The 2016 Revised Irr Of Ra No. 9184 Shall Prevail. 18.2. The Preliminary Examination Of Bids Shall Be Governed By Section 30 Of The 2016 Revised Irr Of Ra No. 9184. 19. Detailed Evaluation And Comparison Of Bids 19.1. The Procuring Entity’s Bac Shall Immediately Conduct A Detailed Evaluation Of All Bids Rated “passed” Using Non-discretionary Pass/fail Criteria. The Bac Shall Consider The Conditions In The Evaluation Of Bids Under Section 32.2 Of 2016 Revised Irr Of Ra No. 9184. 19.2. If The Project Allows Partial Bids, All Bids And Combinations Of Bids As Indicated In The Bds Shall Be Received By The Same Deadline And Opened And Evaluated Simultaneously So As To Determine The Bid Or Combination Of Bids Offering The Lowest Calculated Cost To The Procuring Entity. Bid Security As Required By Itb Clause 16 Shall Be Submitted For Each Contract (lot) Separately. 19.3. In All Cases, The Nfcc Computation Pursuant To Section 23.4.2.6 Of The 2016 Revised Irr Of Ra No. 9184 Must Be Sufficient For The Total Of The Abcs For All The Lots Participated In By The Prospective Bidder. 20. Post Qualification Within A Non-extendible Period Of Five (5) Calendar Days From Receipt By The Bidder Of The Notice From The Bac That It Submitted The Lowest Calculated Bid, The Bidder Shall Submit Its Latest Income And Business Tax Returns Filed And Paid Through The Bir Electronic Filing And Payment System (efps), And Other Appropriate Licenses And Permits Required By Law And Stated In The Bds. 21. Signing Of The Contract The Documents Required In Section 37.2 Of The 2016 Revised Irr Of Ra No. 9184 Shall Form Part Of The Contract. Additional Contract Documents Are Indicated In The Bds. Section Iii. Bid Data Sheet Itb Clause 5.2 For This Purpose, Contracts Similar To The Project Refer To Contracts Which Have The Same Major Categories Of Work, Which Shall Be: A) Construction Of Swine Artificial Insemination Building 7.1 The Procuring Entity Has Prescribed That Subcontracting Is Not Allowed. 10.3 Special Philippine Contractors Accreditation Board License 10.4 The Key Personnel Must Meet The Required Minimum Years Of Experience Set Below: Key Personnel General Experience Relevant Experience Project Engineer 1 Year 1 Year Material Engineer 1 Year 1 Year Agricultural And Biosystems Engineer 1 Year 1 Year Health And Safety Officer 1 Year 1 Year 1-foreman 1 Year 1 Year 1-skilled Worker 1 Year 1 Year 1-unskilled Worker 1 Year 1 Year The Minimum Major Equipment Requirements Are The Following: Equipment Capacity Number Of Units Welding Machine 1 Generator Set 1 One Bagger Mixer 1 Concrete Vibrator 1 Bar Cutter 1 Pneumatic Tire Roller 1 12 Alternative Bids Are Not Allowed The Bid Security Shall Be In The Form Of A Bid Securing Declaration Or Any Of The Following Forms And Amounts: A. The Amount Of Not Less Than Two Percent (2%) Of Abc, If Bid Security Is In Cash, Cashier’s/manager’s Check, Bank Draft/guarantee Or Irrevocable Letter Of Credit; B. The Amount Of Not Less Than Five Percent (5%) Of Abc If Bid Security Is In Surety Bond. 19.2 Partial Bid Is Not Allowed 20 No Further Instructions. 21 The Additional Contract Documents Relevant To The Project That Are Required By The Procuring Entity Are: A. Construction Schedule And S-curve; B. Manpower Schedule; C. Construction Methods; D. Equipment Utilization Schedule; E. Construction Safety And Health Program Approved By The Department Of Labor And Employment; And F. Pert/cpm Section Iv. General Conditions Of Contract 1. Scope Of Contract This Contract Shall Include All Such Items, Although Not Specifically Mentioned, That Can Be Reasonably Inferred As Being Required For Its Completion As If Such Items Were Expressly Mentioned Herein. All The Provisions Of Ra No. 9184 And Its 2016 Revised Irr, Including The Generic Procurement Manual, And Associated Issuances, Constitute The Primary Source For The Terms And Conditions Of The Contract, And Thus, Applicable In Contract Implementation. Herein Clauses Shall Serve As The Secondary Source For The Terms And Conditions Of The Contract. This Is Without Prejudice To Sections 74.1 And 74.2 Of The 2016 Revised Irr Of Ra No. 9184 Allowing The Gppb To Amend The Irr, Which Shall Be Applied To All Procurement Activities, The Advertisement, Posting, Or Invitation Of Which Were Issued After The Effectivity Of The Said Amendment. 2. Sectional Completion Of Works If Sectional Completion Is Specified In The Special Conditions Of Contract (scc), References In The Conditions Of Contract To The Works, The Completion Date, And The Intended Completion Date Shall Apply To Any Section Of The Works (other Than References To The Completion Date And Intended Completion Date For The Whole Of The Works). 3. Possession Of Site 4.1. The Procuring Entity Shall Give Possession Of All Or Parts Of The Site To The Contractor Based On The Schedule Of Delivery Indicated In The Scc, Which Corresponds To The Execution Of The Works. If The Contractor Suffers Delay Or Incurs Cost From Failure On The Part Of The Procuring Entity To Give Possession In Accordance With The Terms Of This Clause, The Procuring Entity’s Representative Shall Give The Contractor A Contract Time Extension And Certify Such Sum As Fair To Cover The Cost Incurred, Which Sum Shall Be Paid By Procuring Entity. 4.2. If Possession Of A Portion Is Not Given By The Above Date, The Procuring Entity Will Be Deemed To Have Delayed The Start Of The Relevant Activities. The Resulting Adjustments In Contract Time To Address Such Delay May Be Addressed Through Contract Extension Provided Under Annex “e” Of The 2016 Revised Irr Of Ra No. 9184. 4. The Contractor’s Obligations The Contractor Shall Employ The Key Personnel Named In The Schedule Of Key Personnel Indicating Their Designation, In Accordance With Itb Clause 10.3 And Specified In The Bds, To Carry Out The Supervision Of The Works. The Procuring Entity Will Approve Any Proposed Replacement Of Key Personnel Only If Their Relevant Qualifications And Abilities Are Equal To Or Better Than Those Of The Personnel Listed In The Schedule. 5. Performance Security 5.1. Within Ten (10) Calendar Days From Receipt Of The Notice Of Award From The Procuring Entity But In No Case Later Than The Signing Of The Contract By Both Parties, The Successful Bidder Shall Furnish The Performance Security In Any Of The Forms Prescribed In Section 39 Of The 2016 Revised Irr. 5.2. The Contractor, By Entering Into The Contract With The Procuring Entity, Acknowledges The Right Of The Procuring Entity To Institute Action Pursuant To Ra No. 3688 Against Any Subcontractor Be They An Individual, Firm, Partnership, Corporation, Or Association Supplying The Contractor With Labor, Materials And/or Equipment For The Performance Of This Contract. 6. Site Investigation Reports The Contractor, In Preparing The Bid, Shall Rely On Any Site Investigation Reports Referred To In The Scc Supplemented By Any Information Obtained By The Contractor. 7. Warranty 7.1. In Case The Contractor Fails To Undertake The Repair Works Under Section 62.2.2 Of The 2016 Revised Irr, The Procuring Entity Shall Forfeit Its Performance Security, Subject Its Property(ies) To Attachment Or Garnishment Proceedings, And Perpetually Disqualify It From Participating In Any Public Bidding. All Payables Of The Gop In His Favor Shall Be Offset To Recover The Costs. 7.2. The Warranty Against Structural Defects/failures, Except That Occasioned-on Force Majeure, Shall Cover The Period From The Date Of Issuance Of The Certificate Of Final Acceptance By The Procuring Entity. Specific Duration Of The Warranty Is Found In The Scc. 8. Liability Of The Contractor Subject To Additional Provisions, If Any, Set Forth In The Scc, The Contractor’s Liability Under This Contract Shall Be As Provided By The Laws Of The Republic Of The Philippines. If The Contractor Is A Joint Venture, All Partners To The Joint Venture Shall Be Jointly And Severally Liable To The Procuring Entity. 9. Termination For Other Causes Contract Termination Shall Be Initiated In Case It Is Determined Prima Facie By The Procuring Entity That The Contractor Has Engaged, Before, Or During The Implementation Of The Contract, In Unlawful Deeds And Behaviors Relative To Contract Acquisition And Implementation, Such As, But Not Limited To Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices As Stated In Itb Clause 4. 10. Dayworks Subject To The Guidelines On Variation Order In Annex “e” Of The 2016 Revised Irr Of Ra No. 9184, And If Applicable As Indicated In The Scc, The Dayworks Rates In The Contractor’s Bid Shall Be Used For Small Additional Amounts Of Work Only When The Procuring Entity’s Representative Has Given Written Instructions In Advance For Additional Work To Be Paid For In That Way. 11. Program Of Work 11.1. The Contractor Shall Submit To The Procuring Entity’s Representative For Approval The Said Program Of Work Showing The General Methods, Arrangements, Order, And Timing For All The Activities In The Works. The Submissions Of The Program Of Work Are Indicated In The Scc. 11.2. The Contractor Shall Submit To The Procuring Entity’s Representative For Approval An Updated Program Of Work At Intervals No Longer Than The Period Stated In The Scc. If The Contractor Does Not Submit An Updated Program Of Work Within This Period, The Procuring Entity’s Representative May Withhold The Amount Stated In The Scc From The Next Payment Certificate And Continue To Withhold This Amount Until The Next Payment After The Date On Which The Overdue Program Of Work Has Been Submitted. 12. Instructions, Inspections And Audits The Contractor Shall Permit The Gop Or The Procuring Entity To Inspect The Contractor’s Accounts And Records Relating To The Performance Of The Contractor And To Have Them Audited By Auditors Of The Gop Or The Procuring Entity, As May Be Required. 13. Advance Payment The Procuring Entity Shall, Upon A Written Request Of The Contractor Which Shall Be Submitted As A Contract Document, Make An Advance Payment To The Contractor In An Amount Not Exceeding Fifteen Percent (15%) Of The Total Contract Price, To Be Made In Lump Sum, Or At The Most Two Installments According To A Schedule Specified In The Scc, Subject To The Requirements In Annex “e” Of The 2016 Revised Irr Of Ra No. 9184. 14. Progress Payments The Contractor May Submit A Request For Payment For Work Accomplished. Such Requests For Payment Shall Be Verified And Certified By The Procuring Entity’s Representative/project Engineer. Except As Otherwise Stipulated In The Scc, Materials And Equipment Delivered On The Site But Not Completely Put In Place Shall Not Be Included For Payment. 15. Operating And Maintenance Manuals 15.1. If Required, The Contractor Will Provide “as Built” Drawings And/or Operating And Maintenance Manuals As Specified In The Scc. 15.2. If The Contractor Does Not Provide The Drawings And/or Manuals By The Dates Stated Above, Or They Do Not Receive The Procuring Entity’s Representative’s Approval, The Procuring Entity’s Representative May Withhold The Amount Stated In The Scc From Payments Due To The Contractor. Section V. Special Conditions Of Contract Gcc Clause 2 As Per Construction Schedule/contract Period 3.1 The Procuring Entity Shall Give Possession Of All Parts Of The Site To The Contractor Upon Effectivity Of The Contracts. 6 No Further Instructions 7.2 [in Case Of Permanent Structures, Such As Buildings Of Types 4 And 5 As Classified Under The National Building Code Of The Philippines And Other Structures Made Of Steel, Iron, Or Concrete Which Comply With Relevant Structural Codes (e.g., Dpwh Standard Specifications), Such As, But Not Limited To, Steel/concrete Bridges, Flyovers, Aircraft Movement Areas, Ports, Dams, Tunnels, Filtration And Treatment Plants, Sewerage Systems, Power Plants, Transmission And Communication Towers, Railway System, And Other Similar Permanent Structures:] Fifteen (15) Years. 10 Dayworks Are Applicable At The Rate Shown In The Contractor’s Original Bid. 11.1 No Further Instructions 11.2 No Further Instructions 13 The Amount Of The Advance Shall Not Exceed 15% Of The Total Contract Price. 14 Materials And Equipment Delivered On The Site But Not Completely Put In Place Shall Not Be Included For Payment. 15.1 The Date By Which Operating And Maintenance Manuals Are Required Shall Be At Least 5 Days Before The Testing And Commissioning. The Date By Which “as Built” Drawings Are Required Shall Be At Least 10 Days Prior To The Final Billing. 15.2 The Amount To Be Withheld For Failing To Produce “as Built” Drawings And/or Operating And Maintenance Manuals By The Date Required Is 1% Of The Final Contract Amount. Section Vi. Specifications General Requirements All Works To Be Done Shall Be With First Class Workmanship And Shall Conform To The Plans And Specifications. All Materials To Be Used Shall Be Of Good Quality And Properly Inspected By The Authorized Representative Or The Engineer In-charge. The Provincial Agriculturist Is Reserved The Right To Rescind, Terminate, Suspend The Contract If He Deems Necessary And To The Best Interest Of The Government. The Contractor Shall Be Liable For All Damages That Will Occur During The Construction Of The Project. Scope Of Works The Works Include Furnishing Of Labor, Materials, Tools, Equipment And Other Incidentals Necessary To Complete The Project Such As Construction Of Swine Artificial Insemination Building And Biosecurity Building, Concrete Drainage Canal, And Powerhouse. General Condition A. The Works To Be Done Herein Shall Be The Construction Of Swine Artificial Insemination Building As Of Approved And Of Quality Materials Completed As Per Plans, Details And Specifications. Supervision Of The Work Shall Be Done Under The Responsibility Of The Project Engineer With The Help Of The Construction Foreman. B. All Materials Employed And To Be Used In The Construction Shall Be Brand New, Unless Otherwise Or As Directed And Approved By The Project Engineer. C. Skilled Workmen And Workmanship Subject To Project Engineer’s Approval Shall Perform Methods Of The Construction In The Most Acceptable Manner. D. The Drawings Referred To In The Specifications Including Supplementary One, To Be Furnished As The Work Progress Are Intended To Cooperate With The Specification And To Form Part Hereof. Where Figures Are Given, They Are To Be Followed In Performance To Measurement By Scale. E. The Assigned Engineer Or Construction Foreman Shall Lay – Out The Building In Accordance With The Drawings And Directions On Plans As He Shall Not Only Responsible But Liable For Any Failure To Comply In This Respect With The Said Drawings, Specifications And Directions For Its Due And Accurate Location On The Lot. Project Sign Board / Billboard The Contractor Shall Ensure That The Project Site Is Identified With Information Billboard Which Shall Be Erected At The Beginning And Ending Of The Proposed Project. The Layout Of The Billboard Shall Accord To The Specifications Pursuant To The Commission On Audit (coa) Circular No. 2013-004 Issued On January 30, 2013. Coa Billboard Pao Billboard The Billboard’s Specifications Shall Conform To The Following Requirements: A. Tarpaulin, White, 8ft X 8ft (coa) And 4ft X 8ft (pao): B. Resolution: 70 Dpi; C. Font: Helvetica; D. Font Size: Main Information – 3”; E. Sub-information – 1”; F. Font Color: Black; G. Suitable Frame: Rigid Wood Or Steel Frame With Post; And, H. Posting: Outside Display At The Project Location After Award Has Been Made. Measurement The Supply And Erection Of Project Billboard Shall Be In Accordance With Provisions Of This Specification. Basis Of Payment No Additional Payment Shall Be Made In This Regard. A) Swine Artificial Insemination Building & Biosecurity Building Clearing, Grubbing And Staking Clearing And Grubbing And Cutting Of Trees Shall Include Handling, Salvaging, Piling And Disposing Off The Cleared Materials With All Leads And Lifts. Trees Shall Be Cut In Sections From The Top Downwards. All Timber Shall Not Be Used By The Contractor For Any Purpose And Shall Remain The Property Of The Provincial Agriculture Office. Clearing Shall Consist Of The Cutting, Removing And Disposal Of All Trees, Bushes, Shrubs, Grass, Weeds, Other Vegetation, Anthills, Rubbish, Fences, Top Organic Soil And Rocks And Boulders Exposed Or Lying On The Surface. The Construction Site Shall Be Leveled According To The Plans And Cleared Of Rubbish, Roots And Other Perishable And Objectionable Matters To A Suitable Subgrade. All Such Unsuitable Materials Shall Be Removed From The Construction Site And Spread Uniformly Over The Areas Adjacent To The Proposed Building, Or Otherwise Disposed Of As Maybe Directed By The Architect/engineer In-charge Of The Construction. Materials Obtained From Clearing And Grubbing Shall Be Disposed Of In Borrow Pits Or Other Suitable Places And Be Covered Up With Soil Or Gravel As Directed By The Engineer. The Burning Of Combustible Materials Shall Not Be Permitted. Staking-out The Building Lines Shall Be Staked Out On The Lines And Grades Shown In The Drawings Established Before Any Excavation Is Started. Batter Boards And Reference Marks Shall Be Erected At Such Place Where They Will Not Be Disturbed During The Excavation Of The Building. During The Period Of Commencement Of Works, The Contractor Shall Survey The Construction Area And Confirm The Levels. He Shall Immediately Notify The Engineer Of Any Discrepancies And Shall Agree With The Engineer Any Amended Values On The Plan. All Stations And Reference Points Shall Be Clearly Marked And Protected To The Satisfaction Of The Engineer. All Working Benchmarks Shall Be Near Major/medium Structure Sites. Accurate Establishment Of The Centerlines Based On The Drawing Is Required. The Existing Profile And Cross-section Shall Be Jointly Taken With The Engineer. Excavation Works Foundation Trench Shall Be Dug To The Exact Width And Depth And Levels As Indicated In The Drawings. Sides Of The Trenches Shall Be Vertical. In Case Soil Does Not Permit Vertical Sides, The Contractor Shall Protect The Sides With Timber Shoring. Excavated Earth Shall Not Be Placed Within 1.5 Meter Of The Edge Of The Trench. No Excavation Or Foundation Work Shall Be Filled In Or Covered Up Before The Inspection And Approval Of The Project Engineer. Backfill, Embankment And Gravel Bedding Use Earth Or Sand Free From Waste And Objectionable Materials. Place Backfill And Embank In Uniform Horizontal Layer Not More 150mm Thick At A Time, Puddle And Tamper Each Layer As Required To Make Firm Adequate Compaction. Fill Bottom Of Excavation For Structured Foundation With At Least 100mm Thk Gravel Before Placing Reinforcing Steel Bars And Pouring Concrete. Concrete, Masonry And Plastering Works A. General: All Concrete Works To Be Done Herein Shall Be In Accordance With Aci Requirement And/ Or Standard Specifications As Adopted By The Government. B. Cement Shall Be Portland Cement (type1) With 40 Kgs/bag. C. Fine Aggregates Shall Be Clean Hold River Sand, Free From Injurious Amount Of Clay, Loam And Vegetable Matter. D. Coarse Aggregates Shall Be River Run Gravel Or Broken Stones. The Maximum Size Shall Be 1/5 Of The Nearest Dimensions Between Side Forms Of The Concrete Members Or ¾ The Maximum Clear Spacing Between Reinforcing Bars. E. Reinforcing Bars: Reinforcing Bars Shall Be Intermediate Grade And Deformed And Shall Have Minimum Yield Strength Of 275 Mpa (40,000 Psi) F. The Wires Shall Be Locally Produced G.i. Wire Gauge No. 16. G. Placing Reinforcement Provide Bars, Wire Fabrics, Wire Ties, Supports And Other Devices Necessary To Install And Secure Reinforcement. Reinforcement Shall Not Contain Rust, Scale Oil, Grease Clay And Foreign Substances That Would Reduce The Bond. Rusting Of Reinforcement Is A Basis Of Rejection If The Effective Cross-sectional Area Of The Normal Weight Per Foot Of The Reinforcement Has Been Reduced To Less Than Specified In Paragraph Entitled “reinforcing Bars”. Remove Loose Rust Prior To Placing Of Steel. Splices Shall Be Approved Prior To Use. Do Not Splice At Points Of Maximum Stress. Overlapped Welded Wire Fabric The Spacing Of The Cross Wires, Plus 50 Mm (2 Inches). H. Concrete Hollow Blocks: 1. For Walls And Partitions, Use Chb Or Its Equivalent. 2. Minimum Comprehensive Strength Shall Be 700 Psi. I. All Concrete Cured For Least Seven (7) Days To Twenty-eight (28) Days If Possible After Placement To Attain The Required Strength Of Concrete. J. Removal Of Forms: Forms Shall Be Removed In Such A Manner As Not To Impair The Safety And Serviceability Of The Structures. K. Mixture For Plastering: Thickness Of Plaster Shall Be 16mm Thick. A Mixture Of Washed Sand And Portland Cement. Roof & Roof Framing A. All Roofing Must Be 0.5mm Pre-painted Rib-type Long Span With Compatible Ridge Roll, Gutter And Fascia. B. All Trusses Shall Be ¼” Thick X 2” X 2” Angle Bars For Top And Bottom Chord And All Web Members. C. For Girt Use ¼” Thick X 2” X 2” Angle Bar For Top And Bottom Chord And All Web Members. D. For Fascia Frame Use 1/4” Thick X 1” X 1” Angle Bar With 1”x1/4” Thick Flat Bar Braces. E. Use 2” X 6” Light Gauge C-purlins. F. Fasten Framing Members Together By Welding Or By Using Bolts. Welding Shall Conform To Aws D1.3 Welding Procedure. G. All Metal Surfaces Must Be Metal Primer Red Oxide Painted. Ceiling Works All Materials Shall Be Of Kind And Size Specified On Plans. Interior And Exterior Ceiling Will Use 4” Spandrel Ceiling With A Carrying Channel, Metal Furring And Wall Angle For Corner As Main Frame. Use Blind Rivets To Fix The Spandrel To The Main Frame. Tile Works Tiles Should Be Installed In Biosecurity Building Using A 0.60mx0.60m Granite Tile. Shall Have Tile Trim At The Edges And Provide Tile Grout Between Tiles. It Should Be Done By A Tile Setter To Ensure Quality Workmanship. Doors And Windows With Complete Accessories For Swine Artificial Insemination Building: Use Wooden Panel Door 1.0m X 2.10m Dimension With Complete Accessories. For Biosecurity Building: Use 1.0m X 2.10m Wooden Panel Door For The Feed Warehouse And 0.90m X 2.10m Wooden Panel Door For The Lobby And Ai Laboratory And Pvc Door 0.70m X 2.10m Dimension With Complete Accessories At Comfort Room. For Biosecurity Building: Windows Are Analoc Sliding Glass Window With 1.20m X 1.20m Dimension Should Be Installed In Feed Warehouse And Ai Laboratory, Clear Awning Glass Window With 0.6m X 1.20m Dimension To Be Installed In Lobby, Clear Awning Glass Window With 0.6mx0.4m Dimension To Be Installed In Toilet And Shower Room And 0.3mx0.4m Clear Awning Glass Window, Dimension, Should Be Installed In Changing Room. Electrical Works The Electrical Installation Shall Be Done In Accordance With The Approved Plans And Under The Direct Supervision And Control Of A Professional Electrical Engineer And Or Registered Electrical Engineer. All Electrical Works And Materials Shall Conform To The Provisions Of The Latest Edition Of The Philippine National Electrical Code. The Type Of Electrical Services To Be Supplied To The Building Shall Be 240v, Ac Single Phase Or Three Phase. There Shall Only One Service To Be Dropped From The Nearest Or Local Electrical Company Pole For The Proposed Building. See Attached Plans For Specifications. Provide 3pcs- 3” Gi Pipe Schedule 40 With Concrete Foundation That Will Serve As Post For Electrical Wirings. Plumbing Works All Works Shall Be Done In Accordance With The Provisions Of The Latest Edition Of The Plumbing Code And Local Ordinance. All Works Shall Be Done Under The Direct Supervision Of A Duly Licensed Master Plumber. See Attached Plans For Specifications. Painting Works I. Complete Painting Covers All Concrete And Other Interior Parts Except Otherwise Specified. Ii. Apply Three (3) Coats As Paint Follows: 1st Coat = Sealer 2nd Coat = Primer 3rd Coat = Color Selected And Approved (2 Coats) Iii. Paint Shall Be Thoroughly Dry Before Applying The Succeeding Coat No Exterior Painting Shall Be Done With The Surface To Be Applied Is Damp Or During Rainy Weather Iv. Proper Works At All Times By Suitable Materials As Work Progress, Upon Completion Of Work, Remove All Paints Stains And Varnish Spots From Floors And Other Surfaces, Leave Work Clean And In Acceptable Condition. Installation Of Pig Pens For The Main Frame: Use 2-1/2”ø Schedule 40 Gi Pipe For The Vertical Grill: Use 1/2”ø Schedule 40 Gi Pipe Spaced At 0.15m On Center. For Pen Gate: Shall Be 0.6m Wide And Atleast 1m High. Use For The Dummy Sow : Shall Be 1.20m Height, Use 4” Ø Schedule 40 Gi Pipe Filled With Concrete Mixture Spaced At 0.20m On Center. Feeding Trough: Shall Be Atleast 0.30m And 0.25m Depth. Biogas Plant Excavation Shall Be Dug To The Exact Width And Depth And Levels As Indicated In The Drawings. Sides Of The Trenches Shall Be Vertical. In Case Soil Does Not Permit Vertical Sides, The Contractor Shall Protect The Sides With Timber Shoring. Excavated Earth Shall Not Be Placed Within 1.5 Meter Of The Edge Of The Trench. No Excavation Or Foundation Work Shall Be Filled In Or Covered Up Before The Inspection And Approval Of The Project Engineer. All Concrete Works To Be Done Herein Shall Be In Accordance With Aci Requirement And/ Or Standard Specifications As Adopted By The Government. Cement Shall Be Portland Cement (type1) With 40 Kgs/bag. Fine Aggregates Shall Be Clean Hold River Sand, Free From Injurious Amount Of Clay, Loam And Vegetable Matter. Coarse Aggregates Shall Be River Run Gravel Or Broken Stones. The Maximum Size Shall Be 1/5 Of The Nearest Dimensions Between Side Forms Of The Concrete Members Or ¾ The Maximum Clear Spacing Between Reinforcing Bars. Reinforcing Bars Shall Be Intermediate Grade And Deformed And Shall Have Minimum Yield Strength Of 275 Mpa (40,000 Psi). The Wires Shall Be Locally Produced G.i. Wire Gauge No. 16. Provide Bars, Wire Fabrics, Wire Ties, Supports And Other Devices Necessary To Install And Secure Reinforcement. Reinforcement Shall Not Contain Rust, Scale Oil, Grease Clay And Foreign Substances That Would Reduce The Bond. Rusting Of Reinforcement Is A Basis Of Rejection If The Effective Cross Sectional Area Of The Normal Weight Per Foot Of The Reinforcement Has Been Reduced To Less Than Specified In Paragraph Entitled “reinforcing Bars”. Remove Loose Rust Prior To Placing Of Steel. Splices Shall Be Approved Prior To Use. Do Not Splice At Points Of Maximum Stress. Overlapped Welded Wire Fabric The Spacing Of The Cross Wires, Plus 50 Mm (2 Inches). Concrete Hollow Blocks Minimum Comprehensive Strength Shall Be 700 Psi. All Concrete Cured For Least Seven (7) Days To Twenty-eight (28) Days If Possible After Placement To Attain The Required Strength Of Concrete. Removal Of Forms: Forms Shall Be Removed In Such A Manner As Not To Impair The Safety And Serviceability Of The Structures. All Connections From Collecting Pit To Earth Lagoon Must Use 150mmø Pvc Pipe S-1000. All Finished Concrete Walls And Slab Must Have Waterproofing. Tunnel Ventilating System With Installation See Attached Plans For Specifications. B) Concrete Drainage Canal Excavation Works Foundation Trench Shall Be Dug To The Exact Width And Depth And Levels As Indicated In The Drawings. Sides Of The Trenches Shall Be Vertical. In Case Soil Does Not Permit Vertical Sides, The Contractor Shall Protect The Sides With Timber Shoring. Excavated Earth Shall Not Be Placed Within 1.5 Meter Of The Edge Of The Trench. No Excavation Or Foundation Work Shall Be Filled In Or Covered Up Before The Inspection And Approval Of The Project Engineer. Concrete Works A. General: All Concrete Works To Be Done Herein Shall Be In Accordance With Aci Requirement And/ Or Standard Specifications As Adopted By The Government. B. Cement Shall Be Portland Cement (type1) With 40 Kgs/bag. C. Fine Aggregates Shall Be Clean Hold River Sand, Free From Injurious Amount Of Clay, Loam And Vegetable Matter. D. Coarse Aggregates Shall Be River Run Gravel Or Broken Stones. The Maximum Size Shall Be 1/5 Of The Nearest Dimensions Between Side Forms Of The Concrete Members Or ¾ The Maximum Clear Spacing Between Reinforcing Bars. E. Reinforcing Bars: Reinforcing Bars Shall Be Intermediate Grade And Deformed And Shall Have Minimum Yield Strength Of 275 Mpa (40,000 Psi) F. The Wires Shall Be Locally Produced G.i. Wire Gauge No. 16. G. Placing Reinforcement Provide Bars, Wire Fabrics, Wire Ties, Supports And Other Devices Necessary To Install And Secure Reinforcement. Reinforcement Shall Not Contain Rust, Scale Oil, Grease Clay And Foreign Substances That Would Reduce The Bond. Rusting Of Reinforcement Is A Basis Of Rejection If The Effective Cross-sectional Area Of The Normal Weight Per Foot Of The Reinforcement Has Been Reduced To Less Than Specified In Paragraph Entitled “reinforcing Bars”. Remove Loose Rust Prior To Placing Of Steel. Splices Shall Be Approved Prior To Use. Do Not Splice At Points Of Maximum Stress. Overlapped Welded Wire Fabric The Spacing Of The Cross Wires, Plus 50 Mm (2 Inches). H. All Concrete Cured For Least Seven (7) Days To Twenty-eight (28) Days If Possible After Placement To Attain The Required Strength Of Concrete. I. Removal Of Forms: Forms Shall Be Removed In Such A Manner As Not To Impair The Safety And C) Powerhouse Excavation Works Foundation Trench Shall Be Dug To The Exact Width And Depth And Levels As Indicated In The Drawings. Sides Of The Trenches Shall Be Vertical. In Case Soil Does Not Permit Vertical Sides, The Contractor Shall Protect The Sides With Timber Shoring. Excavated Earth Shall Not Be Placed Within 1.5 Meter Of The Edge Of The Trench. No Excavation Or Foundation Work Shall Be Filled In Or Covered Up Before The Inspection And Approval Of The Project Engineer. Backfill And Gravel Bedding Use Earth Or Sand Free From Waste And Objectionable Materials. Place Backfill And Embank In Uniform Horizontal Layer Not More 150mm Thick At A Time, Puddle And Tamper Each Layer As Required To Make Firm Adequate Compaction. Fill Bottom Of Excavation For Structured Foundation With At Least 100mm Thk Gravel Before Placing Reinforcing Steel Bars And Pouring Concrete. Concrete, Masonry And Plastering Works A. General: All Concrete Works To Be Done Herein Shall Be In Accordance With Aci Requirement And/ Or Standard Specifications As Adopted By The Government. B. Cement Shall Be Portland Cement (type1) With 40 Kgs/bag. C. Fine Aggregates Shall Be Clean Hold River Sand, Free From Injurious Amount Of Clay, Loam And Vegetable Matter. D. Coarse Aggregates Shall Be River Run Gravel Or Broken Stones. The Maximum Size Shall Be 1/5 Of The Nearest Dimensions Between Side Forms Of The Concrete Members Or ¾ The Maximum Clear Spacing Between Reinforcing Bars. E. Reinforcing Bars: Reinforcing Bars Shall Be Intermediate Grade And Deformed And Shall Have Minimum Yield Strength Of 275 Mpa (40,000 Psi) F. The Wires Shall Be Locally Produced G.i. Wire Gauge No. 16. G. Placing Reinforcement Provide Bars, Wire Fabrics, Wire Ties, Supports And Other Devices Necessary To Install And Secure Reinforcement. Reinforcement Shall Not Contain Rust, Scale Oil, Grease Clay And Foreign Substances That Would Reduce The Bond. Rusting Of Reinforcement Is A Basis Of Rejection If The Effective Cross-sectional Area Of The Normal Weight Per Foot Of The Reinforcement Has Been Reduced To Less Than Specified In Paragraph Entitled “reinforcing Bars”. Remove Loose Rust Prior To Placing Of Steel. Splices Shall Be Approved Prior To Use. Do Not Splice At Points Of Maximum Stress. Overlapped Welded Wire Fabric The Spacing Of The Cross Wires, Plus 50 Mm (2 Inches). H. Concrete Hollow Blocks: 1. For Walls And Partitions, Use Chb Or Its Equivalent. 2. Minimum Comprehensive Strength Shall Be 700 Psi. I. All Concrete Cured For Least Seven (7) Days To Twenty-eight (28) Days If Possible After Placement To Attain The Required Strength Of Concrete. J. Removal Of Forms: Forms Shall Be Removed In Such A Manner As Not To Impair The Safety And Serviceability Of The Structures. K. Mixture For Plastering: Thickness Of Plaster Shall Be 16mm Thick. A Mixture Of Washed Sand And Portland Cement. Roof & Roof Framing A. All Roofing Must Be 0.4mm Pre-painted Rib-type Long Span With Insulation And With Compatible Ridge Roll, Gutter And Fascia. B. All Rafter And Center Girt Shall Be 2” X 6” Light Gauge C-purlins With 10mm Diameter Web Member C. For Fascia Frame Use 3/16” Thick X 1” X 1” Flat Bar. D. Use 2” X 4” Light Gauge C-purlins With 12mm Diameter Bar Support. E. Fasten Framing Members Together By Welding Or By Using Bolts. Welding Shall Conform To Aws D1.3 Welding Procedure. F. All Metal Surfaces Must Be Metal Primer Red Oxide Painted. Doors And Windows With Complete Accessories For Entrance Door And Windows Use 2”ø Sched 40 Gi Pipe Frame Enclosed With #6 Steel Matting With 1” Thick Flat Bar Holder Welded To The Frame. Hinges And Locks Must Be Fabricated. Installation Of Generator Set Generator Set Power Rating: 55kva Phase: 3-phase Voltage: 230v Frequency: 60 Hz Engine: Diesel Engine Type: Silent Type Manual Transfer Switch Rating: 150 At Phase/pole: 3-phase/ 3-pole Voltage Capacity: 250vac Section Vii. Drawings Annex A – Architectural Design Annex B – Project Billboard Plan Section Viii. Bill Of Quantities Bid No. Agr- 24-932-b Item Description Quantity Unit Unit Cost Total Cost No. A. Swine Artificial Insemination Building And Biosecurity Building I. Clearing, Grubbing And Staking 675.00 Sq.m. Pesos And Ctvs. (p ) / Sq.m P Ii. Excavation Works 129.45 Cu.m. Pesos And Ctvs. (p ) / Cu.m P Iii. Backfilling Works 19.10 Cu.m. Pesos And Ctvs. (p ) / Cu.m P Iv. Embankment 2,091.00 Cu.m Pesos And Ctvs. (p ) / Cu.m V. Concrete Works A. Concreting 49.16 Cu.m Pesos And Ctvs. (p ) / Cu.m P B. Steel Works 3,818.48 Kg Pesos And Ctvs. (p ) / Kg P C. Form Works 263.05 Sq.m. Pesos And Ctvs. (p ) / Sq.m. P D. Gravel Bedding 18.00 Cu.m. Pesos And Ctvs. (p ) / Cu.m. P Vi. Masonry Works 384.00 Sq.m. Pesos And Ctvs. (p ) / Sq.m P Vii. Plastering Works 573.08 Sq.m Pesos And Ctvs. (p ) / Sq.m P Viii Roofing Works 311.00 Sq.m. Pesos And Ctvs. (p ) / Sq.m P Ix. Ceiling Works 203.79 Sq.m. Pesos And Ctvs. (p ) / Sq.m P X. Tile Works 64.11 Sq.m. Pesos And Ctvs. (p ) / Sq.m P Xi. Door And Windows With Complete Accessories 1.00 Lot Pesos And Ctvs. (p ) / Lot P Xii. Plumbing Works 1.00 Lot Pesos And Ctvs. (p ) / Lot P Xiii. Electrical Works 1.00 Lot Pesos And Ctvs. ) / Lot P Xiv. Painting Works 722.61 Sq.m. Pesos And Ctvs. (p ) / Sq.m P Xv. Installation Of Pig Pens 1.00 Lot Pesos And Ctvs P (p ) / Lot Xvi. Biogas Plant 1.00 Lot Pesos And Ctvs. (p ) / Lot P Xvii. Tunnel Ventilating System With Installation 1.00 Lot Pesos And Ctvs. (₱ ) / Lot P B. Concrete Drainage Canal I. Excavation 300.00 Cu.m Pesos And Ctvs. (₱ ) / Cu.m` P Ii. Concrete Works A. Concreting 91.00 Cu.m Pesos And Ctvs. (₱ ) / Cu.m` P B. Steel Works 5,874.00 Kg Pesos And Ctvs. (₱ ) / Kg P B. Form Works 1,380.00 Sq.m Pesos And Ctvs. (₱ ) / Sq.m P B. Gravel Bedding 15.00 Cu.m Pesos And Ctvs. (₱ ) / Cu.m P C. Powerhouse I. Excavation Works 6.40 Cu.m Pesos And Ctvs. (₱ ) / Cu.m P Ii. Backfilling Works 4.20 Cu.m Pesos And Ctvs. (₱ ) / Cu.m P Iii. Concrete Works A. Concreting 12.00 Cu.m Pesos And Ctvs. (₱ ) / Cu.m P B. Steel Works 1,141.00 Kg Pesos And Ctvs. (₱ ) / Kg P C. Form Works 23.52 Sq.m Pesos And Ctvs. (₱ ) / Sq.m P D. Gravel Bedding 4.00 Cu.m Pesos And Ctvs. (₱ ) / Cu.m P Iv. Masonry And Plastering Works 72.56 Sq.m Pesos And Ctvs. (₱ ) / Sq.m P V. Roofing Works 67.00 Sq.m Pesos And Ctvs. (₱ ) / Sq.m P Vi. Door And Windows With Complete Accessories 1.00 Lot Pesos And Ctvs. (₱ ) / Lot P Vii. Installation Of Generator Set 1.00 Lot Pesos And Ctvs. (₱ ) / Lot P Total Bid Cost In Figures P Total Bid Cost In Words Summary Of Costs Item No. Bid Amount A. Swine Artificial Insemination Building And Biosecurity Building I. Clearing, Grubbing And Staking ₽________________________________ Ii. Excavation Works ₽________________________________ Iii. Backfilling Works ₽________________________________ Iv. Embankment ₽________________________________ V. Concrete Works A. Concreting ₽________________________________ B. Steel Works ₽________________________________ C. Form Works ₽________________________________ D. Gravel Bedding ₽________________________________ Vi. Masonry Works ₽________________________________ Vii. Plastering Works ₽________________________________ Viii. Roofing Works ₽________________________________ Ix. Ceiling Works ₽________________________________ X. Tile Works ₽________________________________ Xi. Door And Windows With Complete Accessories ₽________________________________ Xii. Plumbing Works ₽________________________________ Xiii. Electrical Works ₽________________________________ Xiv. Painting Works ₽________________________________ Xv. Installation Of Pig Pens ₽________________________________ Xvi. Biogas Plant ₽________________________________ Xvii. Tunnel Ventilating System With Installation ₽________________________________ B. Concrete Drainage Canal I. Excavation ₽________________________________ Ii. Concrete Works A. Concreting ₽________________________________ B. Steel Works ₽________________________________ C. Form Works ₽________________________________ D. Gravel Bedding ₽________________________________ C. Powerhouse I. Excavation Works ₽________________________________ Ii. Backfilling Works ₽________________________________ Iii. Concrete Works A. Concreting ₽________________________________ B. Steel Works ₽________________________________ C. Form Works ₽________________________________ D. Gravel Bedding ₽________________________________ Iv. Masonry And Plastering Works ₽________________________________ V. Roofing Works Vi. Door And Windows With Complete Accessories ₽________________________________ Vii. Installation Of Generator Set ₽________________________________ Total Bid Amount ₽________________________________ Section Ix. Checklist Of Technical And Financial Documents I. Technical Component Envelope Class “a” Documents Legal Documents ⬜ (a) Valid Philgeps Registration Certificate (platinum Membership) (all Pages) In Accordance With Section 8.5.2 Of The Irr; Technical Documents ⬜ (b) Statement Of The Prospective Bidder Of All Its Ongoing Government And Private Contracts, Including Contracts Awarded But Not Yet Started, If Any, Whether Similar Or Not Similar In Nature And Complexity To The Contract To Be Bid; And ⬜ (c) Statement Of The Bidder’s Single Largest Completed Contract (slcc) Similar To The Contract To Be Bid, Except Under Conditions Provided Under The Rules; And ⬜ (d) Special Pcab License In Case Of Joint Ventures; And Registration For The Type And Cost Of The Contract To Be Bid; And ⬜ (e) Original Copy Of Bid Security. If In The Form Of A Surety Bond, Submit Also A Certification Issued By The Insurance Commission; Or Original Copy Of Notarized Bid Securing Declaration; And (f) Project Requirements, Which Shall Include The Following: ⬜ A. Organizational Chart For The Contract To Be Bid; ⬜ B. List Of Contractor’s Key Personnel (e.g., Project Manager, Project Engineers, Materials Engineers, And Foremen), To Be Assigned To The Contract To Be Bid, With Their Complete Qualification And Experience Data; ⬜ C. List Of Contractor’s Major Equipment Units, Which Are Owned, Leased, And/or Under Purchase Agreements, Supported By Proof Of Ownership Or Certification Of Availability Of Equipment From The Equipment Lessor/vendor For The Duration Of The Project, As The Case May Be; And ⬜ (g) Original Duly Signed Omnibus Sworn Statement (oss); And If Applicable, Original Notarized Secretary’s Certificate In Case Of A Corporation, Partnership, Or Cooperative; Or Original Special Power Of Attorney Of All Members Of The Joint Venture Giving Full Power And Authority To Its Officer To Sign The Oss And Do Acts To Represent The Bidder. Financial Documents ⬜ (h) The Prospective Bidder’s Computation Of Net Financial Contracting Capacity (nfcc). Class “b” Documents ⬜ (i) If Applicable, Duly Signed Joint Venture Agreement (jva) In Accordance With Ra No. 4566 And Its Irr In Case The Joint Venture Is Already In Existence; Or Duly Notarized Statements From All The Potential Joint Venture Partners Stating That They Will Enter Into And Abide By The Provisions Of The Jva In The Instance That The Bid Is Successful. Ii. Financial Component Envelope ⬜ (j) Original Of Duly Signed And Accomplished Financial Bid Form; And Other Documentary Requirements Under Ra No. 9184 ⬜ (k) Original Of Duly Signed Bid Prices In The Bill Of Quantities; And ⬜ (l) Duly Accomplished Detailed Estimates Form, Including A Summary Sheet Indicating The Unit Prices Of Construction Materials, Labor Rates, And Equipment Rentals Used In Coming Up With The Bid; And ⬜ Cash Flow By Quarter. Bid Form For The Procurement Of Infrastructure Projects [shall Be Submitted With The Bid] Bid Form Date : Project Identification No. : To: [name And Address Of Procuring Entity] Having Examined The Philippine Bidding Documents (pbds) Including The Supplemental Or Bid Bulletin Numbers [insert Numbers], The Receipt Of Which Is Hereby Duly Acknowledged, We, The Undersigned, Declare That: A. We Have No Reservation To The Pbds, Including The Supplemental Or Bid Bulletins, For The Procurement Project: [insert Name Of Contract]; B. We Offer To Execute The Works For This Contract In Accordance With The Pbds; C. The Total Price Of Our Bid In Words And Figures, Excluding Any Discounts Offered Below Is: [insert Information]; D. The Discounts Offered And The Methodology For Their Application Are: [insert Information]; E. The Total Bid Price Includes The Cost Of All Taxes, Such As, But Not Limited To: [specify The Applicable Taxes, E.g. (i) Value Added Tax (vat), (ii) Income Tax, (iii) Local Taxes, And (iv) Other Fiscal Levies And Duties], Which Are Itemized Herein And Reflected In The Detailed Estimates, F. Our Bid Shall Be Valid Within The A Period Stated In The Pbds, And It Shall Remain Binding Upon Us At Any Time Before The Expiration Of That Period; G. If Our Bid Is Accepted, We Commit To Obtain A Performance Security In The Amount Of [insert Percentage Amount] Percent Of The Contract Price For The Due Performance Of The Contract, Or A Performance Securing Declaration In Lieu Of The The Allowable Forms Of Performance Security, Subject To The Terms And Conditions Of Issued Gppb Guidelines12 For This Purpose; H. We Are Not Participating, As Bidders, In More Than One Bid In This Bidding Process, Other Than Alternative Offers In Accordance With The Bidding Documents; I. We Understand That This Bid, Together With Your Written Acceptance Thereof Included In Your Notification Of Award, Shall Constitute A Binding Contract Between Us, Until A Formal Contract Is Prepared And Executed; And J. We Understand That You Are Not Bound To Accept The Lowest Calculated Bid Or Any Other Bid That You May Receive. K. We Likewise Certify/confirm That The Undersigned, Is The Duly Authorized Representative Of The Bidder, And Granted Full Power And Authority To Do, Execute 12 Currently Based On Gppb Resolution No. 09-2020 And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For The [name Of Project] Of The [name Of The Procuring Entity]. L. We Acknowledge That Failure To Sign Each And Every Page Of This Bid Form, Including The Bill Of Quantities, Shall Be A Ground For The Rejection Of Our Bid. Name: Legal Capacity: Signature: Duly Authorized To Sign The Bid For And Behalf Of: Date: Bid Securing Declaration Form [shall Be Submitted With The Bid If Bidder Opts To Provide This Form Of Bid Security] Republic Of The Philippines) City Of ) S.s. Bid Securing Declaration Project Identification No.: [insert Number To: [insert Name And Address Of The Procuring Entity] I/we, The Undersigned, Declare That: 1. I/we Understand That, According To Your Conditions, Bids Must Be Supported By A Bid Security, Which May Be In The Form Of A Bid Securing Declaration. 2. I/we Accept That: (a) I/we Will Be Automatically Disqualified From Bidding For Any Procurement Contract With Any Procuring Entity For A Period Of Two (2) Years Upon Receipt Of Your Blacklisting Order; And, (b) I/we Will Pay The Applicable Fine Provided Under Section 6 Of The Guidelines On The Use Of Bid Securing Declaration, Within Fifteen (15) Days From Receipt Of The Written Demand By The Procuring Entity For The Commission Of Acts Resulting To The Enforcement Of The Bid Securing Declaration Under Sections 23.1(b), 34.2, 40.1 And 69.1, Except 69.1(f),of The Irr Of Ra No. 9184; Without Prejudice To Other Legal Action The Government May Undertake. 3. I/we Understand That This Bid Securing Declaration Shall Cease To Be Valid On The Following Circumstances: A. Upon Expiration Of The Bid Validity Period, Or Any Extension Thereof Pursuant To Your Request; B. I Am/we Are Declared Ineligible Or Post-disqualified Upon Receipt Of Your Notice To Such Effect, And (i) I/we Failed To Timely File A Request For Reconsideration Or (ii) I/we Filed A Waiver To Avail Of Said Right; And C. I Am/we Are Declared The Bidder With The Lowest Calculated Responsive Bid, And I/we Have Furnished The Performance Security And Signed The Contract. In Witness Whereof, I/we Have Hereunto Set My/our Hand/s This Day Of [month] [year] At [place Of Execution]. [insert Name Of Bidder Or Its Authorized Representative] [insert Signatory’s Legal Capacity] Affiant [jurat] [format Shall Be Based On The Latest Rules On Notarial Practice] Omnibus Sworn Statement (revised) [shall Be Submitted With The Bid] Republic Of The Philippines ) City/municipality Of ) S.s. Affidavit I, [name Of Affiant], Of Legal Age, [civil Status], [nationality], And Residing At [address Of Affiant], After Having Been Duly Sworn In Accordance With Law, Do Hereby Depose And State That: 1. [select One, Delete The Other:] [if A Sole Proprietorship:] I Am The Sole Proprietor Or Authorized Representative Of [name Of Bidder] With Office Address At [address Of Bidder]; [if A Partnership, Corporation, Cooperative, Or Joint Venture:] I Am The Duly Authorized And Designated Representative Of [name Of Bidder] With Office Address At [address Of Bidder]; 2. [select One, Delete The Other:] [if A Sole Proprietorship:] As The Owner And Sole Proprietor, Or Authorized Representative Of [name Of Bidder], I Have Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For [name Of The Project] Of The [name Of The Procuring Entity], As Shown In The Attached Duly Notarized Special Power Of Attorney; [if A Partnership, Corporation, Cooperative, Or Joint Venture:] I Am Granted Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For [name Of The Project] Of The [name Of The Procuring Entity], As Shown In The Attached [state Title Of Attached Document Showing Proof Of Authorization (e.g., Duly Notarized Secretary’s Certificate, Board/partnership Resolution, Or Special Power Of Attorney, Whichever Is Applicable;)]; 3. [name Of Bidder] Is Not “blacklisted” Or Barred From Bidding By The Government Of The Philippines Or Any Of Its Agencies, Offices, Corporations, Or Local Government Units, Foreign Government/foreign Or International Financing Institution Whose Blacklisting Rules Have Been Recognized By The Government Procurement Policy Board, By Itself Or By Relation, Membership, Association, Affiliation, Or Controlling Interest With Another Blacklisted Person Or Entity As Defined And Provided For In The Uniform Guidelines On Blacklisting; 4. Each Of The Documents Submitted In Satisfaction Of The Bidding Requirements Is An Authentic Copy Of The Original, Complete, And All Statements And Information Provided Therein Are True And Correct; 5. [name Of Bidder] Is Authorizing The Head Of The Procuring Entity Or Its Duly Authorized Representative(s) To Verify All The Documents Submitted; 6. [select One, Delete The Rest:] [if A Sole Proprietorship:] The Owner Or Sole Proprietor Is Not Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; [if A Partnership Or Cooperative:] None Of The Officers And Members Of [name Of Bidder] Is Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; [if A Corporation Or Joint Venture:] None Of The Officers, Directors, And Controlling Stockholders Of [name Of Bidder] Is Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; 7. [name Of Bidder] Complies With Existing Labor Laws And Standards; And 8. [name Of Bidder] Is Aware Of And Has Undertaken The Responsibilities As A Bidder In Compliance With The Philippine Bidding Documents, Which Includes: A. Carefully Examining All Of The Bidding Documents; B. Acknowledging All Conditions, Local Or Otherwise, Affecting The Implementation Of The Contract; C. Making An Estimate Of The Facilities Available And Needed For The Contract To Be Bid, If Any; And D. Inquiring Or Securing Supplemental/bid Bulletin(s) Issued For The [name Of The Project]. 9. [name Of Bidder] Did Not Give Or Pay Directly Or Indirectly, Any Commission, Amount, Fee, Or Any Form Of Consideration, Pecuniary Or Otherwise, To Any Person Or Official, Personnel Or Representative Of The Government In Relation To Any Procurement Project Or Activity. 10. In Case Advance Payment Was Made Or Given, Failure To Perform Or Deliver Any Of The Obligations And Undertakings In The Contract Shall Be Sufficient Grounds To Constitute Criminal Liability For Swindling (estafa) Or The Commission Of Fraud With Unfaithfulness Or Abuse Of Confidence Through Misappropriating Or Converting Any Payment Received By A Person Or Entity Under An Obligation Involving The Duty To Deliver Certain Goods Or Services, To The Prejudice Of The Public And The Government Of The Philippines Pursuant To Article 315 Of Act No. 3815 S. 1930, As Amended, Or The Revised Penal Code. In Witness Whereof, I Have Hereunto Set My Hand This Day Of , 20 At , Philippines. [insert Name Of Bidder Or Its Authorized Representative] [insert Signatory’s Legal Capacity] Affiant [jurat] [format Shall Be Based On The Latest Rules On Notarial Practice]

Details: Description Philippine Bidding Documents (as Harmonized With Development Partners) Improvement Of Gates, Perimeter Fence, Additional Culvert And Access Road At Art Center, Brgy. Nanga, Pototan, Iloilo Bid No. Agr-23-1089-b Iloilo Provincial Government Sixth Edition Table Of Contents Glossary Of Terms, Abbreviations, And Acronyms 4 Section I. Invitation To Bid 7 Section Ii. Instructions To Bidders 9 1. Scope Of Bid 9 2. Funding Information 9 3. Bidding Requirements 9 4. Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices 9 5. Eligible Bidders 10 6. Origin Of Associated Goods 10 7. Subcontracts 10 8. Pre-bid Conference 10 9. Clarification And Amendment Of Bidding Documents 10 10. Documents Comprising The Bid: Eligibility And Technical Components 11 11. Documents Comprising The Bid: Financial Component 11 12. Alternative Bids 11 13. Bid Prices 12 14. Bid And Payment Currencies 12 15. Bid Security 12 16. Sealing And Marking Of Bids 12 17. Deadline For Submission Of Bids 12 18. Opening And Preliminary Examination Of Bids 13 19. Detailed Evaluation And Comparison Of Bids 13 20. Post Qualification 13 21. Signing Of The Contract 13 Section Iii. Bid Data Sheet 14 Section Iv. General Conditions Of Contract 16 1. Scope Of Contract 16 2. Sectional Completion Of Works 16 3. Possession Of Site 16 4. The Contractor’s Obligations 17 5. Performance Security 17 6. Site Investigation Reports 17 7. Warranty 17 8. Liability Of The Contractor 18 9. Termination For Other Causes 18 10. Dayworks 18 11. Program Of Work 18 12. Instructions, Inspections And Audits 18 13. Advance Payment 19 14. Progress Payments 19 15. Operating And Maintenance Manuals 19 Section V. Special Conditions Of Contract 20 Section Vi. Specifications 21 Section Vii. Drawings 28 Section Viii. Bill Of Quantities 31 Section Ix. Checklist Of Technical And Financial Documents 41 Glossary Of Terms, Abbreviations, And Acronyms Abc – Approved Budget For The Contract. Arcc – Allowable Range Of Contract Cost. Bac – Bids And Awards Committee. Bid – A Signed Offer Or Proposal To Undertake A Contract Submitted By A Bidder In Response To And In Consonance With The Requirements Of The Bidding Documents. Also Referred To As Proposal And Tender. (2016 Revised Irr, Section 5[c]) Bidder – Refers To A Contractor, Manufacturer, Supplier, Distributor And/or Consultant Who Submits A Bid In Response To The Requirements Of The Bidding Documents. (2016 Revised Irr, Section 5[d]) Bidding Documents – The Documents Issued By The Procuring Entity As The Bases For Bids, Furnishing All Information Necessary For A Prospective Bidder To Prepare A Bid For The Goods, Infrastructure Projects, And/or Consulting Services Required By The Procuring Entity. (2016 Revised Irr, Section 5[e]) Bir – Bureau Of Internal Revenue. Bsp – Bangko Sentral Ng Pilipinas. Cda – Cooperative Development Authority. Consulting Services – Refer To Services For Infrastructure Projects And Other Types Of Projects Or Activities Of The Gop Requiring Adequate External Technical And Professional Expertise That Are Beyond The Capability And/or Capacity Of The Gop To Undertake Such As, But Not Limited To: (i) Advisory And Review Services; (ii) Pre-investment Or Feasibility Studies; (iii) Design; (iv) Construction Supervision; (v) Management And Related Services; And (vi) Other Technical Services Or Special Studies. (2016 Revised Irr, Section 5[i]) Contract – Refers To The Agreement Entered Into Between The Procuring Entity And The Supplier Or Manufacturer Or Distributor Or Service Provider For Procurement Of Goods And Services; Contractor For Procurement Of Infrastructure Projects; Or Consultant Or Consulting Firm For Procurement Of Consulting Services; As The Case May Be, As Recorded In The Contract Form Signed By The Parties, Including All Attachments And Appendices Thereto And All Documents Incorporated By Reference Therein. Contractor – Is A Natural Or Juridical Entity Whose Proposal Was Accepted By The Procuring Entity And To Whom The Contract To Execute The Work Was Awarded. Contractor As Used In These Bidding Documents May Likewise Refer To A Supplier, Distributor, Manufacturer, Or Consultant. Cpi – Consumer Price Index. Dole – Department Of Labor And Employment. Dti – Department Of Trade And Industry. Foreign-funded Procurement Or Foreign-assisted Project – Refers To Procurement Whose Funding Source Is From A Foreign Government, Foreign Or International Financing Institution As Specified In The Treaty Or International Or Executive Agreement. (2016 Revised Irr, Section 5[b]). Gfi – Government Financial Institution. Gocc – Government-owned And/or –controlled Corporation. Goods – Refer To All Items, Supplies, Materials And General Support Services, Except Consulting Services And Infrastructure Projects, Which May Be Needed In The Transaction Of Public Businesses Or In The Pursuit Of Any Government Undertaking, Project Or Activity, Whether In The Nature Of Equipment, Furniture, Stationery, Materials For Construction, Or Personal Property Of Any Kind, Including Non-personal Or Contractual Services Such As The Repair And Maintenance Of Equipment And Furniture, As Well As Trucking, Hauling, Janitorial, Security, And Related Or Analogous Services, As Well As Procurement Of Materials And Supplies Provided By The Procuring Entity For Such Services. The Term “related” Or “analogous Services” Shall Include, But Is Not Limited To, Lease Or Purchase Of Office Space, Media Advertisements, Health Maintenance Services, And Other Services Essential To The Operation Of The Procuring Entity. (2016 Revised Irr, Section 5[r]) Gop – Government Of The Philippines. Infrastructure Projects – Include The Construction, Improvement, Rehabilitation, Demolition, Repair, Restoration Or Maintenance Of Roads And Bridges, Railways, Airports, Seaports, Communication Facilities, Civil Works Components Of Information Technology Projects, Irrigation, Flood Control And Drainage, Water Supply, Sanitation, Sewerage And Solid Waste Management Systems, Shore Protection, Energy/power And Electrification Facilities, National Buildings, School Buildings, Hospital Buildings, And Other Related Construction Projects Of The Government. Also Referred To As Civil Works Or Works. (2016 Revised Irr, Section 5[u]) Lgus – Local Government Units. Nfcc – Net Financial Contracting Capacity. Nga – National Government Agency. Pcab – Philippine Contractors Accreditation Board. Philgeps - Philippine Government Electronic Procurement System. Procurement Project – Refers To A Specific Or Identified Procurement Covering Goods, Infrastructure Project Or Consulting Services. A Procurement Project Shall Be Described, Detailed, And Scheduled In The Project Procurement Management Plan Prepared By The Agency Which Shall Be Consolidated In The Procuring Entity's Annual Procurement Plan. (gppb Circular No. 06-2019 Dated 17 July 2019) Psa – Philippine Statistics Authority. Sec – Securities And Exchange Commission. Slcc – Single Largest Completed Contract. Un – United Nations. Republic Of The Philippines Iloilo Provincial Government Section I. Invitation To Bid For Improvement Of Gates, Perimeter Fence, Additional Culvert, And Access Road At Art Center, Brgy. Nanga, Pototan, Iloilo Bid No. Agr-23-1089-b 1. The Iloilo Provincial Government, Through The 20% Nta Development Fund Fy-2022 – Other Land Improvements Intends To Apply The Sum Of P1,800,000.00 Being The Approved Budget For The Contract (abc) To Payments Under The Contract For Agr-23-1089-b For The Improvement Of Gates, Perimeter Fence, Additional Culvert, And Access At Art Center, Brgy. Nanga, Pototan, Iloilo For The Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. 2. The Iloilo Provincial Government Now Invites Bids For The Above Procurement Project. Completion Of The Works Is Required Seventy-five (75) Calendar Days. Bidders Should Have Completed A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii (instructions To Bidders). 3. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) No. 9184. 4. Interested Bidders May Obtain Further Information From The Bids And Awards Committee Secretariat, 5th Floor, New Iloilo Provincial Capitol, Bonifacio Drive, Iloilo City, Philippines And Inspect The Bidding Documents At The Address Given Below From 8:00am To 5:00pm. 5. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders On December 15, 2023 From Given Address And Website/s Below And Upon Payment Of The Applicable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb, In The Amount Of Five Thousand Pesos (p5, 000.00). The Procuring Entity Shall Allow The Bidder To Present Its Proof Of Payment For The Fees In Person. 6. The Iloilo Provincial Government Will Hold A Pre-bid Conference On December 22, 2023 9:00 A.m. At Bids And Awards Committee Secretariat, 5th Floor, New Iloilo Provincial Capitol, Bonifacio Drive, Iloilo City, Philippines, And/or Through Videoconferencing/webcasting Via Zoom Conference Which Shall Be Open To Prospective Bidders. The Default Meeting Id And Password Shall Be: Meeting Id: 434 085 1724 // Password: 0922 7. Bids Must Be Duly Received By The Bac Secretariat Through Manual Submission At The Office Address At Ground Floor, Lobby, Iloilo Provincial Capitol, Iloilo City On Or Before January 10, 9:00 A.m.. Late Bids Shall Not Be Accepted. 8. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 16. 9. Bid Opening Shall Be On January 10, 9:00 A.m. At Bids And Awards Committee Secretariat, 5th Floor, New Iloilo Provincial Capitol, Bonifacio Drive, Iloilo City, Philippines. Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend The Activity. 10. The Iloilo Provincial Government Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Implementing Rules And Regulations (irr) Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 11. For Further Information, Please Refer To: Atty. Raemman M. Lagrada Head, Bac Secretariat 5f New Iloilo Provincial Capitol Bonifacio Drive, Iloilo City Tel. No. (33) 336-0736 Fax No. (33) 337-7731 Email:iph_bacs@yahoo.com 12. You May Visit The Following Websites: For Downloading Of Bidding Documents: Www.iloilo.gov.ph December 11, 2023 Atty. Dennis T. Ventilacion Bac Chairperson Section Ii. Instructions To Bidders 1. Scope Of Bid The Procuring Entity, Iloilo Provincial Government Invites Bids For The Improvement Of Gates, Perimeter Fence, Additional Culvert, And Access Road At Art Center, Brgy. Nanga, Pototan, Iloilo With Project Identification Number Agr-23-1089-b. The Procurement Project (referred To Herein As “project”) Is For The Construction Of Works, As Described In Section Vi (specifications). 2. Funding Information 2.1. The Gop Through The Source Of Funding As Indicated Below For 2022 In The Amount Of One Million Eight Hundred Thousand Pesos (p1,800,000.00) 2.2. The Source Of Funding Is: A. 20% Nta Development Fund Fy 2022 – Other Land Improvements 3. Bidding Requirements The Bidding For The Project Shall Be Governed By All The Provisions Of Ra No. 9184 And Its 2016 Revised Irr, Including Its Generic Procurement Manual And Associated Policies, Rules And Regulations As The Primary Source Thereof, While The Herein Clauses Shall Serve As The Secondary Source Thereof. Any Amendments Made To The Irr And Other Gppb Issuances Shall Be Applicable Only To The Ongoing Posting, Advertisement, Or Invitation To Bid By The Bac Through The Issuance Of A Supplemental Or Bid Bulletin. The Bidder, By The Act Of Submitting Its Bid, Shall Be Deemed To Have Inspected The Site, Determined The General Characteristics Of The Contracted Works And The Conditions For This Project, Such As The Location And The Nature Of The Work; (b) Climatic Conditions; (c) Transportation Facilities; (c) Nature And Condition Of The Terrain, Geological Conditions At The Site Communication Facilities, Requirements, Location And Availability Of Construction Aggregates And Other Materials, Labor, Water, Electric Power And Access Roads; And (d) Other Factors That May Affect The Cost, Duration And Execution Or Implementation Of The Contract, Project, Or Work And Examine All Instructions, Forms, Terms, And Project Requirements In The Bidding Documents. 4. Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices The Procuring Entity, As Well As The Bidders And Contractors, Shall Observe The Highest Standard Of Ethics During The Procurement And Execution Of The Contract. They Or Through An Agent Shall Not Engage In Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices Defined Under Annex “i” Of The 2016 Revised Irr Of Ra No. 9184 Or Other Integrity Violations In Competing For The Project. 5. Eligible Bidders 5.1. Only Bids Of Bidders Found To Be Legally, Technically, And Financially Capable Will Be Evaluated. 5.2. The Bidder Must Have An Experience Of Having Completed A Single Largest Completed Contract (slcc) That Is Similar To This Project, Equivalent To At Least Fifty Percent (50%) Of The Abc Adjusted, If Necessary, By The Bidder To Current Prices Using The Psa’s Cpi, Except Under Conditions Provided For In Section 23.4.2.4 Of The 2016 Revised Irr Of Ra No. 9184. A Contract Is Considered To Be “similar” To The Contract To Be Bid If It Has The Major Categories Of Work Stated In The Bds. 5.3. For Foreign-funded Procurement, The Procuring Entity And The Foreign Government/foreign Or International Financing Institution May Agree On Another Track Record Requirement, As Specified In The Bidding Document Prepared For This Purpose. 5.4. The Bidders Shall Comply With The Eligibility Criteria Under Section 23.4.2 Of The 2016 Irr Of Ra No. 9184. 6. Origin Of Associated Goods There Is No Restriction On The Origin Of Goods Other Than Those Prohibited By A Decision Of The Un Security Council Taken Under Chapter Vii Of The Charter Of The Un. 7. Subcontracts 7.1. The Bidder May Subcontract Portions Of The Project To The Extent Allowed By The Procuring Entity As Stated Herein, But In No Case More Than Fifty Percent (50%) Of The Project. The Procuring Entity Has Prescribed That: A. Subcontracting Is Not Allowed. 8. Pre-bid Conference The Procuring Entity Will Hold A Pre-bid Conference For This Project On The Specified Date And Time And Either At Its Physical Address At Bac Office, 5th Floor, New Iloilo Provincial Capitol, Iloilo City And/or Through Videoconferencing As Indicated In Paragraph 6 Of The Ib. 9. Clarification And Amendment Of Bidding Documents Prospective Bidders May Request For Clarification On And/or Interpretation Of Any Part Of The Bidding Documents. Such Requests Must Be In Writing And Received By The Procuring Entity, Either At Its Given Address Or Through Electronic Mail Indicated In The Ib, At Least Ten (10) Calendar Days Before The Deadline Set For The Submission And Receipt Of Bids. 10. Documents Comprising The Bid: Eligibility And Technical Components 10.1. The First Envelope Shall Contain The Eligibility And Technical Documents Of The Bid As Specified In Section Ix. Checklist Of Technical And Financial Documents. 10.2. If The Eligibility Requirements Or Statements, The Bids, And All Other Documents For Submission To The Bac Are In Foreign Language Other Than English, It Must Be Accompanied By A Translation In English, Which Shall Be Authenticated By The Appropriate Philippine Foreign Service Establishment, Post, Or The Equivalent Office Having Jurisdiction Over The Foreign Bidder’s Affairs In The Philippines. For Contracting Parties To The Apostille Convention, Only The Translated Documents Shall Be Authenticated Through An Apostille Pursuant To Gppb Resolution No. 13-2019 Dated 23 May 2019. The English Translation Shall Govern, For Purposes Of Interpretation Of The Bid. 10.3. In Joint Ventures, A Special Pcab License, And Registration For The Type And Cost Of The Contract For This Project, Shall Be Required. Any Additional Type Of Contractor License Or Permit Shall Be Indicated In The Bds. 10.4. A List Of Contractor’s Key Personnel (e.g., Project Manager, Project Engineers, Materials Engineers, And Foremen) Assigned To The Contract To Be Bid, With Their Complete Qualification And Experience Data Shall Be Provided. These Key Personnel Must Meet The Required Minimum Years Of Experience Set In The Bds. 10.5. A List Of Contractor’s Major Equipment Units, Which Are Owned, Leased, And/or Under Purchase Agreements, Supported By Proof Of Ownership, Certification Of Availability Of Equipment From The Equipment Lessor/vendor For The Duration Of The Project, As The Case May Be, Must Meet The Minimum Requirements For The Contract Set In The Bds. 11. Documents Comprising The Bid: Financial Component 11.1. The Second Bid Envelope Shall Contain The Financial Documents For The Bid As Specified In Section Ix. Checklist Of Technical And Financial Documents. 11.2. Any Bid Exceeding The Abc Indicated In Paragraph 1 Of The Ib Shall Not Be Accepted. 11.3. For Foreign-funded Procurement, A Ceiling May Be Applied To Bid Prices Provided The Conditions Are Met Under Section 31.2 Of The 2016 Revised Irr Of Ra No. 9184. 12. Alternative Bids Bidders Shall Submit Offers That Comply With The Requirements Of The Bidding Documents, Including The Basic Technical Design As Indicated In The Drawings And Specifications. Unless There Is A Value Engineering Clause In The Bds, Alternative Bids Shall Not Be Accepted. 13. Bid Prices All Bid Prices For The Given Scope Of Work In The Project As Awarded Shall Be Considered As Fixed Prices, And Therefore Not Subject To Price Escalation During Contract Implementation, Except Under Extraordinary Circumstances As Determined By The Neda And Approved By The Gppb Pursuant To The Revised Guidelines For Contract Price Escalation Guidelines. 14. Bid And Payment Currencies 14.1. Bid Prices May Be Quoted In The Local Currency Or Tradeable Currency Accepted By The Bsp At The Discretion Of The Bidder. However, For Purposes Of Bid Evaluation, Bids Denominated In Foreign Currencies Shall Be Converted To Philippine Currency Based On The Exchange Rate As Published In The Bsp Reference Rate Bulletin On The Day Of The Bid Opening. 14.2. Payment Of The Contract Price Shall Be Made In: A. Philippine Pesos. 15. Bid Security 15.1. The Bidder Shall Submit A Bid Securing Declaration Or Any Form Of Bid Security In The Amount Indicated In The Bds, Which Shall Be Not Less Than The Percentage Of The Abc In Accordance With The Schedule In The Bds. 15.2. The Bid And Bid Security Shall Be Valid Until November 5, 2022. Any Bid Not Accompanied By An Acceptable Bid Security Shall Be Rejected By The Procuring Entity As Non-responsive. 16. Sealing And Marking Of Bids Each Bidder Shall Submit One Copy Of The First And Second Components Of Its Bid. The Procuring Entity May Request Additional Hard Copies And/or Electronic Copies Of The Bid. However, Failure Of The Bidders To Comply With The Said Request Shall Not Be A Ground For Disqualification. If The Procuring Entity Allows The Submission Of Bids Through Online Submission To The Given Website Or Any Other Electronic Means, The Bidder Shall Submit An Electronic Copy Of Its Bid, Which Must Be Digitally Signed. An Electronic Copy That Cannot Be Opened Or Is Corrupted Shall Be Considered Non-responsive And, Thus, Automatically Disqualified. 17. Deadline For Submission Of Bids The Bidders Shall Submit On The Specified Date And Time And Either At Its Physical Address Or Through Online Submission As Indicated In Paragraph 7 Of The Ib. 18. Opening And Preliminary Examination Of Bids 18.1. The Bac Shall Open The Bids In Public At The Time, On The Date, And At The Place Specified In Paragraph 9 Of The Ib. The Bidders’ Representatives Who Are Present Shall Sign A Register Evidencing Their Attendance. In Case Videoconferencing, Webcasting Or Other Similar Technologies Will Be Used, Attendance Of Participants Shall Likewise Be Recorded By The Bac Secretariat. In Case The Bids Cannot Be Opened As Scheduled Due To Justifiable Reasons, The Rescheduling Requirements Under Section 29 Of The 2016 Revised Irr Of Ra No. 9184 Shall Prevail. 18.2. The Preliminary Examination Of Bids Shall Be Governed By Section 30 Of The 2016 Revised Irr Of Ra No. 9184. 19. Detailed Evaluation And Comparison Of Bids 19.1. The Procuring Entity’s Bac Shall Immediately Conduct A Detailed Evaluation Of All Bids Rated “passed” Using Non-discretionary Pass/fail Criteria. The Bac Shall Consider The Conditions In The Evaluation Of Bids Under Section 32.2 Of 2016 Revised Irr Of Ra No. 9184. 19.2. If The Project Allows Partial Bids, All Bids And Combinations Of Bids As Indicated In The Bds Shall Be Received By The Same Deadline And Opened And Evaluated Simultaneously So As To Determine The Bid Or Combination Of Bids Offering The Lowest Calculated Cost To The Procuring Entity. Bid Security As Required By Itb Clause 16 Shall Be Submitted For Each Contract (lot) Separately. 19.3. In All Cases, The Nfcc Computation Pursuant To Section 23.4.2.6 Of The 2016 Revised Irr Of Ra No. 9184 Must Be Sufficient For The Total Of The Abcs For All The Lots Participated In By The Prospective Bidder. 20. Post Qualification Within A Non-extendible Period Of Five (5) Calendar Days From Receipt By The Bidder Of The Notice From The Bac That It Submitted The Lowest Calculated Bid, The Bidder Shall Submit Its Latest Income And Business Tax Returns Filed And Paid Through The Bir Electronic Filing And Payment System (efps), And Other Appropriate Licenses And Permits Required By Law And Stated In The Bds. 21. Signing Of The Contract The Documents Required In Section 37.2 Of The 2016 Revised Irr Of Ra No. 9184 Shall Form Part Of The Contract. Additional Contract Documents Are Indicated In The Bds. Section Iii. Bid Data Sheet Itb Clause 5.2 For This Purpose, Contracts Similar To The Project Refer To Contracts Which Have The Same Major Categories Of Work, Which Shall Be: A) Structural Works 7.1 The Procuring Entity Has Prescribed That Subcontracting Is Not Allowed. 10.3 [specify If Another Contractor License Or Permit Is Required.] 10.4 The Key Personnel Must Meet The Required Minimum Years Of Experience Set Below: Key Personnel General Experience Relevant Experience 1-project Engineer 1 Year 1 Year 1-material Engineer 1 Year 1 Year 1-agricultural & Biosystems Engineer 1 Year 1 Year 1-health & Safety Officer 1 Year 1 Year 1-foreman 1 Year 1 Year 10.5 The Minimum Major Equipment Requirements Are The Following: Equipment Capacity Number Of Units Bar Cutter - 1 Generator - 1 Welding Machine - 1 Plate Compactor - 1 Motorized Road Grader - 1 One Bagger Mixer - 1 Concrete Vibrator - 1 12 Alternative Bids Are Not Allowed 15.1 The Bid Security Shall Be In The Form Of A Bid Securing Declaration Or Any Of The Following Forms And Amounts: A. The Amount Of Not Less Than Two Percent (2%) Of Abc, If Bid Security Is In Cash, Cashier’s/manager’s Check, Bank Draft/guarantee Or Irrevocable Letter Of Credit; B. The Amount Of Not Less Than Five Percent (5%) Of Abc If Bid Security Is In Surety Bond. 19.2 Partial Bid Is Not Allowed 20 No Further Instructions. 21 The Additional Contract Documents Relevant To The Project That Are Required By The Procuring Entity Are: A. Construction Schedule And S-curve; B. Manpower Schedule; C. Construction Methods; D. Equipment Utilization Schedule; E. Construction Safety And Health Program Approved By The Department Of Labor And Employment; And F. Pert/cpm Section Iv. General Conditions Of Contract 1. Scope Of Contract This Contract Shall Include All Such Items, Although Not Specifically Mentioned, That Can Be Reasonably Inferred As Being Required For Its Completion As If Such Items Were Expressly Mentioned Herein. All The Provisions Of Ra No. 9184 And Its 2016 Revised Irr, Including The Generic Procurement Manual, And Associated Issuances, Constitute The Primary Source For The Terms And Conditions Of The Contract, And Thus, Applicable In Contract Implementation. Herein Clauses Shall Serve As The Secondary Source For The Terms And Conditions Of The Contract. This Is Without Prejudice To Sections 74.1 And 74.2 Of The 2016 Revised Irr Of Ra No. 9184 Allowing The Gppb To Amend The Irr, Which Shall Be Applied To All Procurement Activities, The Advertisement, Posting, Or Invitation Of Which Were Issued After The Effectivity Of The Said Amendment. 2. Sectional Completion Of Works If Sectional Completion Is Specified In The Special Conditions Of Contract (scc), References In The Conditions Of Contract To The Works, The Completion Date, And The Intended Completion Date Shall Apply To Any Section Of The Works (other Than References To The Completion Date And Intended Completion Date For The Whole Of The Works). 3. Possession Of Site 4.1. The Procuring Entity Shall Give Possession Of All Or Parts Of The Site To The Contractor Based On The Schedule Of Delivery Indicated In The Scc, Which Corresponds To The Execution Of The Works. If The Contractor Suffers Delay Or Incurs Cost From Failure On The Part Of The Procuring Entity To Give Possession In Accordance With The Terms Of This Clause, The Procuring Entity’s Representative Shall Give The Contractor A Contract Time Extension And Certify Such Sum As Fair To Cover The Cost Incurred, Which Sum Shall Be Paid By Procuring Entity. 4.2. If Possession Of A Portion Is Not Given By The Above Date, The Procuring Entity Will Be Deemed To Have Delayed The Start Of The Relevant Activities. The Resulting Adjustments In Contract Time To Address Such Delay May Be Addressed Through Contract Extension Provided Under Annex “e” Of The 2016 Revised Irr Of Ra No. 9184. 4. The Contractor’s Obligations The Contractor Shall Employ The Key Personnel Named In The Schedule Of Key Personnel Indicating Their Designation, In Accordance With Itb Clause 10.3 And Specified In The Bds, To Carry Out The Supervision Of The Works. The Procuring Entity Will Approve Any Proposed Replacement Of Key Personnel Only If Their Relevant Qualifications And Abilities Are Equal To Or Better Than Those Of The Personnel Listed In The Schedule. 5. Performance Security 5.1. Within Ten (10) Calendar Days From Receipt Of The Notice Of Award From The Procuring Entity But In No Case Later Than The Signing Of The Contract By Both Parties, The Successful Bidder Shall Furnish The Performance Security In Any Of The Forms Prescribed In Section 39 Of The 2016 Revised Irr. 5.2. The Contractor, By Entering Into The Contract With The Procuring Entity, Acknowledges The Right Of The Procuring Entity To Institute Action Pursuant To Ra No. 3688 Against Any Subcontractor Be They An Individual, Firm, Partnership, Corporation, Or Association Supplying The Contractor With Labor, Materials And/or Equipment For The Performance Of This Contract. 6. Site Investigation Reports The Contractor, In Preparing The Bid, Shall Rely On Any Site Investigation Reports Referred To In The Scc Supplemented By Any Information Obtained By The Contractor. 7. Warranty 7.1. In Case The Contractor Fails To Undertake The Repair Works Under Section 62.2.2 Of The 2016 Revised Irr, The Procuring Entity Shall Forfeit Its Performance Security, Subject Its Property(ies) To Attachment Or Garnishment Proceedings, And Perpetually Disqualify It From Participating In Any Public Bidding. All Payables Of The Gop In His Favor Shall Be Offset To Recover The Costs. 7.2. The Warranty Against Structural Defects/failures, Except That Occasioned-on Force Majeure, Shall Cover The Period From The Date Of Issuance Of The Certificate Of Final Acceptance By The Procuring Entity. Specific Duration Of The Warranty Is Found In The Scc. 8. Liability Of The Contractor Subject To Additional Provisions, If Any, Set Forth In The Scc, The Contractor’s Liability Under This Contract Shall Be As Provided By The Laws Of The Republic Of The Philippines. If The Contractor Is A Joint Venture, All Partners To The Joint Venture Shall Be Jointly And Severally Liable To The Procuring Entity. 9. Termination For Other Causes Contract Termination Shall Be Initiated In Case It Is Determined Prima Facie By The Procuring Entity That The Contractor Has Engaged, Before, Or During The Implementation Of The Contract, In Unlawful Deeds And Behaviors Relative To Contract Acquisition And Implementation, Such As, But Not Limited To Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices As Stated In Itb Clause 4. 10. Dayworks Subject To The Guidelines On Variation Order In Annex “e” Of The 2016 Revised Irr Of Ra No. 9184, And If Applicable As Indicated In The Scc, The Dayworks Rates In The Contractor’s Bid Shall Be Used For Small Additional Amounts Of Work Only When The Procuring Entity’s Representative Has Given Written Instructions In Advance For Additional Work To Be Paid For In That Way. 11. Program Of Work 11.1. The Contractor Shall Submit To The Procuring Entity’s Representative For Approval The Said Program Of Work Showing The General Methods, Arrangements, Order, And Timing For All The Activities In The Works. The Submissions Of The Program Of Work Are Indicated In The Scc. 11.2. The Contractor Shall Submit To The Procuring Entity’s Representative For Approval An Updated Program Of Work At Intervals No Longer Than The Period Stated In The Scc. If The Contractor Does Not Submit An Updated Program Of Work Within This Period, The Procuring Entity’s Representative May Withhold The Amount Stated In The Scc From The Next Payment Certificate And Continue To Withhold This Amount Until The Next Payment After The Date On Which The Overdue Program Of Work Has Been Submitted. 12. Instructions, Inspections And Audits The Contractor Shall Permit The Gop Or The Procuring Entity To Inspect The Contractor’s Accounts And Records Relating To The Performance Of The Contractor And To Have Them Audited By Auditors Of The Gop Or The Procuring Entity, As May Be Required. 13. Advance Payment The Procuring Entity Shall, Upon A Written Request Of The Contractor Which Shall Be Submitted As A Contract Document, Make An Advance Payment To The Contractor In An Amount Not Exceeding Fifteen Percent (15%) Of The Total Contract Price, To Be Made In Lump Sum, Or At The Most Two Installments According To A Schedule Specified In The Scc, Subject To The Requirements In Annex “e” Of The 2016 Revised Irr Of Ra No. 9184. 14. Progress Payments The Contractor May Submit A Request For Payment For Work Accomplished. Such Requests For Payment Shall Be Verified And Certified By The Procuring Entity’s Representative/project Engineer. Except As Otherwise Stipulated In The Scc, Materials And Equipment Delivered On The Site But Not Completely Put In Place Shall Not Be Included For Payment. 15. Operating And Maintenance Manuals 15.1. If Required, The Contractor Will Provide “as Built” Drawings And/or Operating And Maintenance Manuals As Specified In The Scc. 15.2. If The Contractor Does Not Provide The Drawings And/or Manuals By The Dates Stated Above, Or They Do Not Receive The Procuring Entity’s Representative’s Approval, The Procuring Entity’s Representative May Withhold The Amount Stated In The Scc From Payments Due To The Contractor. Section V. Special Conditions Of Contract Gcc Clause 2 As Per Construction Schedule/contract Period 3.1 The Procuring Entity Shall Give Possession Of All Parts Of The Site To The Contractor Upon Effectivity Of The Contracts. 6 No Further Instructions 7.2 [in Case Of Permanent Structures, Such As Buildings Of Types 4 And 5 As Classified Under The National Building Code Of The Philippines And Other Structures Made Of Steel, Iron, Or Concrete Which Comply With Relevant Structural Codes (e.g., Dpwh Standard Specifications), Such As, But Not Limited To, Steel/concrete Bridges, Flyovers, Aircraft Movement Areas, Ports, Dams, Tunnels, Filtration And Treatment Plants, Sewerage Systems, Power Plants, Transmission And Communication Towers, Railway System, And Other Similar Permanent Structures:] Fifteen (15) Years. 10 Dayworks Are Applicable At The Rate Shown In The Contractor’s Original Bid. 11.1 No Further Instructions 11.2 No Further Instructions 13 The Amount Of The Advance Shall Not Exceed 15% Of The Total Contract Price. 14 Materials And Equipment Delivered On The Site But Not Completely Installed Or Constructed Shall Not Be Included For Payment. 15.1 The Date By Which Operating And Maintenance Manuals Are Required Shall Be At Least 5 Days Before The Testing And Commissioning. The Date By Which “as Built” Drawings Are Required Prior To The Final Billing. 15.2 The Amount To Be Withheld For Failing To Produce “as Built” Drawings And/or Operating And Maintenance Manuals By The Date Required Is 1% Of The Final Contract Amount. Section Vi. Specification General Requirements All Works To Be Done Shall Be With First Class Workmanship And Shall Conform To The Plans And Specifications. All Materials To Be Used Shall Be Of Good Quality And Properly Inspected By The Authorized Representative Or The Engineer In-charge. The Provincial Agriculturist Is Reserved The Interest Of The Government. The Contractor Shall Be Liable For All Damages That Will Occur During The Construction Of The Project. Scope Of Works The Works Include Furnishing Of Labor, Materials, Tools, Equipment And Other Incidentals Necessary To Complete The Project Such As: Improvement Of Gates: I. Concrete Works Ii. Steel Works Iii. Painting Works Construction Of Perimeter Fence (design 1 – 48m): I. Clearing, Grubbing, And Staking Ii. Excavation Works Iii. Backfill Iv. Concrete Works V. Steel Works Vi. Masonry Vii. Plastering Works Viii. Painting Works Ix. Stone Works Construction Of Perimeter Fence (design 2 – 48m): I. Clearing, Grubbing, And Staking Ii. Excavation Works Iii. Backfill Iv. Concrete Works V. Masonry Vi. Plastering Works Vii. Painting Works Construction Of Additional Culvert: I. Clearing, Grubbing, And Staking Ii. Demolition Works Iii. Excavation Works Iv. Backfill V. Embankment Vi. Concrete Works Vii. Plastering Works Construction Of Access Road: I. Clearing, Grubbing, And Staking Ii. Embankment General Condition A. The Works To Be Done Herein Shall Be The Improvement Of Gates, Perimeter Fence, Additional Culvert, And Access Road As Of Approved And Of Quality Materials Completed As Per Plans, Details And Specifications. Supervision Of The Work Shall Be Done Under The Responsibility Of The Project Engineer With The Help Of The Construction Foreman. B. All Materials Employed And To Be Used In The Construction Shall Be Brand New, Unless Otherwise Or As Directed And Approved By The Project Engineer. C. Skilled Workmen And Workmanship Subject To Project Engineer’s Approval Shall Perform Methods Of The Construction In The Most Acceptable Manner. D. The Drawings Referred To In The Specifications Including Supplementary One, To Be Furnished As The Work Progress Are Intended To Cooperate With The Specification And To Form Part Hereof. Where Figures Are Given, They Are To Be Followed In Performance To Measurement By Scale. E. The Assigned Engineer Or Construction Foreman Shall Lay – Out The Building In Accordance With The Drawings And Directions On Plans As He Shall Not Only Responsible But Liable For Any Failure To Comply In This Respect With The Said Drawings, Specifications And Directions For Its Due And Accurate Location On The Lot. Project Sign Board / Billboard The Contractor Shall Ensure That The Project Site Is Identified With Information Billboard Which Shall Be Erected At The Beginning And Ending Of The Proposed Project. The Layout Of The Billboard Shall Accord To The Specifications Pursuant To The Commission On Audit (coa) Circular No. 2013-004 Issued On January 30, 2013. Coa Billboard Pao Billboard The Billboard’s Specifications Shall Conform To The Following Requirements: A. Tarpaulin, White, 8ft X 8ft (coa) And 4ft X 8ft (pao): B. Resolution: 70 Dpi; C. Font: Helvetica; D. Font Size: Main Information – 3”; E. Sub-information – 1”; F. Font Color: Black; G. Suitable Frame: Rigid Wood Or Steel Frame With Post; And, H. Posting: Outside Display At The Project Location After Award Has Been Made. Measurement The Supply And Erection Of Project Billboard Shall Be In Accordance With Provisions Of This Specification. Basis Of Payment No Additional Payment Shall Be Made In This Regard. Clearing, Grubbing, And Staking Clearing And Grubbing And Cutting Of Trees Shall Include Handling, Salvaging, Piling And Disposing Off The Cleared Materials With All Leads And Lifts. Trees Shall Be Cut In Sections From The Top Downwards. All Timber Shall Not Be Used By The Contractor For Any Purpose And Shall Remain The Property Of The Provincial Agriculture Office. Clearing Shall Consist Of The Cutting, Removing And Disposal Of All Trees, Bushes, Shrubs, Grass, Weeds, Other Vegetation, Anthills, Rubbish, Fences, Top Organic Soil And Rocks And Boulders Exposed Or Lying On The Surface. The Construction Site Shall Be Leveled According To The Plans And Cleared Of Rubbish, Roots And Other Perishable And Objectionable Matters To A Suitable Subgrade. All Such Unsuitable Materials Shall Be Removed From The Construction Site And Spread Uniformly Over The Areas Adjacent To The Proposed Building, Or Otherwise Disposed Of As Maybe Directed By The Architect/engineer In-charge Of The Construction. Materials Obtained From Clearing And Grubbing Shall Be Disposed Off In Borrow Pits Or Other Suitable Places And Be Covered Up With Soil Or Gravel As Directed By The Engineer. The Burning Of Combustible Materials Shall Not Be Permitted. Staking-out The Building Lines Shall Be Staked Out On The Lines And Grades Shown In The Drawings Established Before Any Excavation Is Started. Batter Boards And Reference Marks Shall Be Erected At Such Place Where They Will Not Be Disturbed During The Excavation Of The Building. During The Period Of Commencement Of Works, The Contractor Shall Survey The Construction Area And Confirm The Levels. He Shall Immediately Notify The Engineer Of Any Discrepancies And Shall Agree With The Engineer Any Amended Values On The Plan. All Stations And Reference Points Shall Be Clearly Marked And Protected To The Satisfaction Of The Engineer. All Working Benchmarks Shall Be Near Major/medium Structure Sites. Accurate Establishment Of The Centerlines Based On The Drawing Is Required. The Existing Profile And Cross-section Shall Be Jointly Taken With The Engineer. Demolition Works A. Demolition Operations: Do Not Damage Building Elements And Improvements Indicated To Remain. Storage Or Sale Of Items At Project Site Is Prohibited. B. Occupied Spaces: Do Not Close Or Obstruct Streets, Walks, Drives Or Other Occupied Or Used Spaces Or Facilities Without The Written Permission Of The Owner And The Authorities Having Jurisdiction. Do Not Interrupt Utilities Serving Occupied Or Used Facilities Without The Written Permission Of The Owner And Authorities Having Jurisdiction. If Necessary, Provide Temporary Utilities. C. Operations: Cease Operations If Public Safety Or Remaining Structures Are Endangered. Perform Temporary Corrective Measures Until Operations Can Be Continued Properly. D. Security: Provide Adequate Protection Against Accidental Trespassing. Secure Project After Work Hours. E. Clearing Operations Include The Removal Of Demolished Materials And Objectionable Matter, Protection Of Existing Structures/facilities Left Functional And Clearing To Allow For New Construction Protection Necessary To Prevent Damage To Existing Structures And Facilities. Likewise, Disposal Of Materials, Trash And Debris In A Safe And Acceptable Manner In Accordance With Applicable Laws And Ordinances. Excavation Works Foundation Trench Shall Be Dug To The Exact Width And Depth And Levels As Indicated In The Drawings. Sides Of The Trenches Shall Be Vertical. In Case Soil Does Not Permit Vertical Sides, The Contractor Shall Protect The Sides With Timber Shoring. Excavated Earth Shall Not Be Placed Within 1.5 Meter Of The Edge Of The Trench. No Excavation Or Foundation Work Shall Be Filled In Or Covered Up Before The Inspection And Approval Of The Project Engineer. Backfill, Embankment With Compaction And Gravel Bedding Use Earth Or Sand Free From Waste And Objectionable Materials. Place Backfill And Embank In Uniform Horizontal Layer Not More 150mm Thick At A Time, Puddle And Tamper Each Layer As Required To Make Firm Adequate Compaction. Fill Bottom Of Excavation For Structured Foundation With At Least 100mm Thick Gravel Before Placing Reinforcing Steel Bars And Pouring Concrete. Concrete, Masonry, And Plastering Works A. General: All Concrete Works To Be Done Herein Shall Be In Accordance With Aci Requirement And/ Or Standard Specifications As Adopted By The Government. B. Cement Shall Be Portland Cement (type1) With 40 Kgs/bag. C. Fine Aggregates Shall Be Clean Hold River Sand, Free From Injurious Amount Of Clay, Loam And Vegetable Matter. D. Coarse Aggregates Shall Be River Run Gravel Or Broken Stones. The Maximum Size Shall Be 1/5 Of The Nearest Dimensions Between Side Forms Of The Concrete Members Or ¾ The Maximum Clear Spacing Between Reinforcing Bars. E. Reinforcing Bars: Reinforcing Bars Shall Be Intermediate Grade And Deformed And Shall Have Minimum Yield Strength Of 275 Mpa (40,000 Psi) F. The Wires Shall Be Locally Produced G.i. Wire Gauge No. 16. G. Placing Reinforcement Provide Bars, Wire Fabrics, Wire Ties, Supports And Other Devices Necessary To Install And Secure Reinforcement. Reinforcement Shall Not Contain Rust, Scale Oil, Grease Clay And Foreign Substances That Would Reduce The Bond. Rusting Of Reinforcement Is A Basis Of Rejection If The Effective Cross-sectional Area Of The Normal Weight Per Foot Of The Reinforcement Has Been Reduced To Less Than Specified In Paragraph Entitled “reinforcing Bars”. Remove Loose Rust Prior To Placing Of Steel. Splices Shall Be Approved Prior To Use. Do Not Splice At Points Of Maximum Stress. Overlapped Welded Wire Fabric The Spacing Of The Cross Wires, Plus 50 Mm (2 Inches). H. Concrete Hollow Blocks: 1. For Walls And Partitions, Use Chb Or Its Equivalent. 2. Minimum Comprehensive Strength Shall Be 700 Psi. I. All Concrete Cured For Least Seven (7) Days To Twenty-eight (28) Days If Possible After Placement To Attain The Required Strength Of Concrete. J. Removal Of Forms: Forms Shall Be Removed In Such A Manner As Not To Impair The Safety And Serviceability Of The Structures. K. Proportions Of All Materials Entering Into Concrete Shall Be Of Class “b”. L. Mixture For Concrete Slab: Thickness Of Slab Shall Be 100mm Thick. A Mixture Of Washed Sand, Screened Gravel And Portland Cement. M. Mixture For Plastering: Thickness Of Plaster Shall Be 16mm Thick. A Mixture Of Washed Sand And Portland Cement. Painting Works I. Complete Painting Covers All Concrete Surfaces And Other Interior Parts Except Otherwise Specified. Ii. Apply Two (2) Coats On All Metal Surfaces As Follows: 1st Coat = Neutralizer 2nd Coat = Epoxy Primer With Curing Agent (gray), Color Selected And Approved (2 Coats) Iii. Apply Two (2) Coats On All Concrete Surfaces As Follows: 1st Coat = Neutralizer 2nd Coat = Semi-gloss Latex, Color Selected And Approved (2 Coats) Iv. Paint Shall Be Thoroughly Dry Before Applying The Succeeding Coat No Exterior Painting Shall Be Done With The Surface To Be Applied Is Damp Or During Rainy Weather V. Proper Works At All Times By Suitable Materials As Work Progress, Upon Completion Of Work, Remove All Paints Stains And Varnish Spots From Floors And Other Surfaces, Leave Work Clean And In Acceptable Condition. Improvement Of Gates (3 Units) A. For Frame, Use 2" X 4" X 6m Tubular Steel. B. For Pickets, Use 2" X 3" X 6m Tubular Steel. C. Attach The Pickets To The Rails By Welding (fully-welded). Welding Shall Conform To Aws D1.3 Welding Procedure. D. The Pickets Are Spaced @ 0.0375m (1.5 Inches). E. For Guide Post, Use 2" X 4" X 6m Tubular Steel. F. For Top Guide Roller, Use 2pcs Of 50mm X 100mm Nylon Roller Bearing Guide Wheels G. For Wheels, Use 3pcs – 4"ø V-groove Sliding Gate Double Track Roller H. For Gate Track, Use ¼" X 2" Angle Bar Attached With 5pcs Of ¼" X 2" X 0.5m Angle Bar, Spot-welded I. Refer To Plan For Concreting Of Floor In Gate 1. Proportion Of Mixture Of Concrete Shall Be “class B”. I. For Logo, The Iloilo Provincial Government And Morprogres Logos Should Be Painted On A #26 Plain Gi Sheet. Ipg Logo Size Shall Be 0.85m Ø. The Morprogres Logo Shall Occupy The Other Side Of The Gate. All Colors Should Correspond To The Colors Of Both The Existing Logos. J. For The Swing Gate, Use 2pcs-heavy Duty Hinges And A Locally-fabricated Gate Lock. K. For Gate 2 & 3 (swing Gate), Attach The Gate Leaves To The Existing Post With Two (2) Heavy-duty Hinges And One (1) Drop Bolt On Each Leaf And A Locally-fabricated Gate Lock Placed Outside The Gate. L. For Column On Gate 3, Demolish Part Of The Existing Column And Leave Only 0.90m From The Natural Ground Line. The Main Bars Must Not Be Cut Down To Allow New Main Bars To Anchor To The Old Main Bars. M. Use 12mmø Rsb For Main Bars And 10mmø Rsb For Lateral Ties Spaced @ 0.20m. The New Main Bars Should Be Connected To The Existing Main Bars. N. The Surface Of The Existing Column Should Be Roughened To Ensure The Adhesion Of The New Concrete To Be Poured. Pouring Of New Concrete Should Start Above The Column Footing Of The Existing Column. Proportions For Concrete Materials For Roads Shall Be “class B” Construction Of Perimeter Fence (design 1 - 48m) A. The Perimeter Fence (design 1) Shall Have Sixteen (16) Spans In Total And The Last Span Shall Be Connected To The First Span Of Perimeter Fence (design 2). B. The Column Of The Perimeter Fence Shall Have A Distance Of 0.30m From The Edge Of The Concrete Access Road. C. For Stone Enclosure Mesh, Use 2" X 2" Steel Matting, Welded On An Angle Bar. D. For Stone Enclosure Frame, Use 3/16" X 1-½" Angle Bar, Fully-welded. E. For Stone Enclosure Reinforcement, Use 10mm Ø Reinforcement Steel Bar. F. For Stones, The Sizes Should Be 3-5" Ø. Placing Of Stones Shall Be Done After The Application Of Painting Materials Is Achieved. G. For Fence Mesh Frame, Use 2" Ø Gi Pipe With 3/16" X 1-½" Angle Bar Fully-welded To It. H. For Fence Mesh Screen, Use 2" X 2" Steel Matting, Welded On An Angle Bar. I. The Fence Top Decoration Shall Be Constructed As Per Specified In The Plan. Construction Of Perimeter Fence (design 2 – 48m) A. The Perimeter Fence (design 2) Shall Have Sixteen (16) Spans In Total And The First Span Shall Be Connected To The Last Span Of The Perimeter Fence (design 1). B. The Column Of Perimeter Fence Shall Have A Distance Of 5m From The Mohon/geodetic Monument C. The Fence Top Decoration Shall Be Constructed As Per Specified In The Plan. Construction Of Additional Culvert A. Tire Guard (existing Culvert), Portion Of Fence, And The Structure Beside The Fence Shall Be Demolished Prior To The Commencement Of Construction Of Culvert. Refer To Plan. B. Culvert Bed Shall Be Constructed Prior To The Construction Of Other Parts Of The Culvert. C. Culvert Bed Shall Rest For 24 Hours Prior To Placing Of The Rc Pipes. D. For Rc Pipes, Use 3pcs Of 910mm Ø Rc Pipe. E. The Connecting Edges Of Pipes Should Be Partially Sealed With Concrete. F. The Concrete Encasement Shall Be Poured 24 Hours After The Sealing Of Edges Of Pipe. G. The Head Wall Shall Be Constructed After The Concrete Encasement Has Rested For 24 Hours. H. Reinforcement Bars Of Wing Wall And Apron Shall Be Placed Prior To The Pouring Of Concrete Head Wall. I. Apron, Wing Wall, And Cut-off Wall Shall Then Be Placed After The Reinforcement Bars Have Been Placed. J. Backfill And Embankment With Compaction Shall Be Placed 7 Days After The Pouring Of Apron, Wing Wall, And Cut-off Wall. K. Concreting Of The Portion On Top Of The Embankment Above The Culvert Shall Take Place After Soil Has Been Graded. Refer To Plan. L. Proportion Of Mixture For Culvert And Floor Above The Culvert Shall Be “class A”. Construction Of Access Road A. The Roadway Width Shall Be 5 Meters (including Shoulders). B. The Shoulder Shall Reduce Seepage Adjacent To The Carriageway By Discharging Storm Water Towards The Ditch. C. Prior To Construction Of Embankment, All Necessary Clearing And Grubbing In That Area Shall Have Been Performed In Conformity With Item 100, Clearing And Grubbing D. Embankment Construction Shall Consist Of Constructing Roadway Embankments, Including Preparation Of The Areas Upon Which They Are To Be Placed; The Placing And Compacting Of Approved Material Within Roadway Areas Where Unsuitable Material Has Been Removed; And The Placing And Compacting Of Embankment Material In Holes, Pits, And Other Depressions Within The Roadway Area. E. Embankments And Backfills Shall Contain No Muck, Peat, Sod, Roots, Or Other Deleterious Matter. Rocks, Broken Concrete Or Other Solid, Bulky Materials Shall Not Be Placed In Embankment Areas Where Piling Is To Be Placed Or Driven. F. Where There Is Evidence Of Discrepancies On The Actual Elevations And That Shown On The Plans, A Preconstruction Survey Referred To The Datum Plane Used In The Approved Plan Shall Be Undertaken By The Contractor Under The Control Of The Engineer To Serve As The Basis For The Computation Of The Actual Volume Of The Embankment Materials. G. Effective Spreading Equipment Such As Motorized Road Grader Shall Be Used On Each Lift To Obtain Uniform Thickness As Determined In The Trial Section Prior To Compaction. As The Compaction Of Each Layer Progresses, Continuous Leveling And Manipulating Will Be Required To Assure Uniform Density. H. After The Roadbed Has Been Substantially Completed, The Full Width Shall Be Conditioned By Removing Any Soft Or Other Unstable Material That Will Not Compact Properly Or Serve The Intended Purpose. The Resulting Areas And All Other Low Sections, Holes Or Depressions Shall Be Brought To Grade With Suitable Selected Material. Scarifying, Blading, Dragging, Rolling, Or Other Methods Of Work Shall Be Performed Or Used As Necessary To Provide A Thoroughly Compacted Roadbed Shaped To The Grades And Cross-sections Shown On The Plans Or As Staked By The Engineer. Section Vii. Drawings Annex A – Architectural Design Annex B- Project Billboard Plan Section Viii. Bill Of Quantities Bid No. Agr- 23-1089-b Item Description Quantity Unit Unit Cost Total Cost No. A. Improvement Of Gates (3 Units) I. Concrete Works A. Concreting 10.14 Cu.m. Pesos And Ctvs. (p ) / Cu.m P B. Steel 23.00 Kgs Pesos And Ctvs. (p ) / Kgs P Ii. Steel Works 845.36 Kgs Pesos And Ctvs. (p ) / Kgs P Iii. Painting Works 20.48 Sq.m Pesos And Ctvs. (p ) /sq.m P B. Construction Of Perimeter Fence (design 1 – 48m) I. Clearing, Grubbing, And 200.00 Sq.m. Pesos Staking And Ctvs. (p ) /sq.m P Ii. Excavation Works 62.08 Cu.m. Pesos And Ctvs. (p ) / Cu.m P Iii. Backfill 46.16 Cu.m. Pesos And Ctvs. (p ) / Cu.m P Iv. Concrete Works A. Concreting 19.01 Cu.m. Pesos And Ctvs. (p ) / Cu.m P B. Gravel Bedding 1.22 Cu.m Pesos And Ctvs. (p ) / Cu.m P C. Steel 1,652.80 Kgs Pesos And Ctvs. (p ) / Kgs P D. Formworks 150.32 Sq.m Pesos And Ctvs. (p ) / Sq.m P V. Steel Works 2,145.86 Kgs Pesos And Ctvs. (p ) / Kgs P 8 Vi. Masonry 24.96 Sq.m. Pesos And Ctvs. (p ) / Sq.m P 8 Vii. Plastering Works 30.60 Sq.m. Pesos And Ctvs. (p ) / Sq.m P 8 Viii. Painting Works 72.54 Sq.m. Pesos And Ctvs. (p ) / Sq.m P 8 Ix. Stone Works 9.00 Cu.m. Pesos And Ctvs. (p ) / Cu.m P C. Construction Of Perimeter Fence (design 2 – 48m) I. Clearing, Grubbing, And 96.00 Sq.m. Pesos Staking And Ctvs. (p ) / Sq.m P Ii. Excavation Works 52.48 Cu.m. Pesos And Ctvs. (p ) / Cu.m P Iii. Backfill 18.91 Cu.m. Pesos And Ctvs. (p ) / Cu.m P Iv. Concrete Works A. Concreting 9.90 Cu.m. Pesos And Ctvs. (p ) / Cu.m P B. Gravel Bedding 1.22 Cu.m. Pesos And Ctvs. (p ) / Cu.m P C. Steel 1490.40 Kgs Pesos And Ctvs. (p ) / Kgs P D. Formworks 150.32 Sq.m. Pesos And Ctvs. (p ) / Sq.m P V. Masonry 124.80 Sq.m. Pesos And Ctvs. (p ) / Sq.m P Vi. Plastering Works 325.20 Sq.m. Pesos And Ctvs. (p ) / Sq.m P Vii. Painting Works 327.20 Sq.m. Pesos And Ctvs. (p ) / Sq.m P D. Construction Of Additional Culvert I. Clearing, Grubbing, And 65.60 Sq.m. Pesos Staking And Ctvs. (p ) / Sq.m P Ii. Demolition Works 34.58 Sq.m. Pesos And Ctvs. (p ) / Sq.m P Iii. Excavation Works 8.00 Cu.m. Pesos And Ctvs. (p ) / Cu.m P Iv. Backfill 2.40 Cu.m. Pesos And Ctvs. (p ) / Cu.m P V. Embankment 118.08 Cu.m. Pesos And Ctvs. (p ) / Cu.m P Vi. Concrete Works A. Concreting 28.53 Cu.m. Pesos And Ctvs. (p ) / Cu.m P B. Steel 53.00 Kgs Pesos And Ctvs. (p ) / Kgs P C. Formworks 32.00 Sq.m. Pesos And Ctvs. (p ) / Sq.m P Vii. Plastering Works 10.65 Sq.m. Pesos And Ctvs. (p ) / Sq.m P Viii. Pipe Laying 3.00 Ln.m Pesos And Ctvs. (p ) / Ln.m P E. Construction Of Access Road I. Clearing, Grubbing, And 65.60 Sq.m. Pesos Staking And Ctvs. (p ) / Sq.m P Ii. Embankment 180.00 Cu.m. Pesos And Ctvs. (p ) / Cu.m P Total Bid Cost In Figures P Total Bid Cost In Words Summary Of Costs Item No. Bid Amount A. Improvement Of Gates (3 Units) I. Concrete Works A. Concreting ₱ _____________________________ B. Steel ₱ _____________________________ Ii. Steel Works ₱ _____________________________ Iii. Painting Works ₱ _____________________________ B. Construction Of Perimeter Fence (design 1 – 48m) I. Clearing, Grubbing, And Staking ₱ _____________________________ Ii. Excavation Works ₱ _____________________________ Iii. Backfill ₱ _____________________________ Iv. Concrete Works A. Concreting ₱ _____________________________ B. Gravel Bedding ₱ _____________________________ C. Steel ₱ _____________________________ D. Formworks ₱ _____________________________ V. Steel Works ₱ _____________________________ Vi. Masonry ₱ _____________________________ Vii. Plastering Works ₱ _____________________________ Viii. Painting Works ₱ _____________________________ Ix. Stone Works ₱ _____________________________ C. Construction Of Perimeter Fence (design 2 – 48m) I. Clearing, Grubbing, And Staking ₱ _____________________________ Ii. Excavation Works ₱ _____________________________ Iii. Backfill ₱ _____________________________ Iv. Concrete Works A. Concreting ₱ _____________________________ B. Gravel Bedding ₱ _____________________________ C. Steel ₱ _____________________________ D. Formworks ₱ _____________________________ V. Masonry ₱ _____________________________ Vi. Plastering Works ₱ _____________________________ Vii. Painting Works ₱ _____________________________ D. Construction Of Additional Culvert I. Clearing, Grubbing, And Staking ₱ _____________________________ Ii. Demolition Works ₱ _____________________________ Iii. Excavation Works ₱ _____________________________ Iv. Backfill ₱ _____________________________ V. Embankment ₱ _____________________________ Vi. Concrete Works A. Concreting ₱ _____________________________ B. Steel ₱ _____________________________ C. Formworks ₱ _____________________________ Vii. Plastering Works ₱ _____________________________ Viii. Pipe Laying ₱ _____________________________ E. Construction Of Access Road I. Clearing, Grubbing, And Staking ₱ _____________________________ Ii. Embankment ₱ _____________________________ Total Bid Amount ₱ _____________________________ Section Ix. Checklist Of Technical And Financial Documents I. Technical Component Envelope Class “a” Documents Legal Documents ⬜ (a) Valid Philgeps Registration Certificate (platinum Membership) (all Pages) In Accordance With Section 8.5.2 Of The Irr; Technical Documents ⬜ (b) Statement Of The Prospective Bidder Of All Its Ongoing Government And Private Contracts, Including Contracts Awarded But Not Yet Started, If Any, Whether Similar Or Not Similar In Nature And Complexity To The Contract To Be Bid; And ⬜ (c) Statement Of The Bidder’s Single Largest Completed Contract (slcc) Similar To The Contract To Be Bid, Except Under Conditions Provided Under The Rules; And ⬜ (d) Special Pcab License In Case Of Joint Ventures; And Registration For The Type And Cost Of The Contract To Be Bid; And ⬜ (e) Original Copy Of Bid Security. If In The Form Of A Surety Bond, Submit Also A Certification Issued By The Insurance Commission; Or Original Copy Of Notarized Bid Securing Declaration; And (f) Project Requirements, Which Shall Include The Following: ⬜ A. Organizational Chart For The Contract To Be Bid; ⬜ B. List Of Contractor’s Key Personnel (e.g., Project Manager, Project Engineers, Materials Engineers, And Foremen), To Be Assigned To The Contract To Be Bid, With Their Complete Qualification And Experience Data; ⬜ C. List Of Contractor’s Major Equipment Units, Which Are Owned, Leased, And/or Under Purchase Agreements, Supported By Proof Of Ownership Or Certification Of Availability Of Equipment From The Equipment Lessor/vendor For The Duration Of The Project, As The Case May Be; And ⬜ (g) Original Duly Signed Omnibus Sworn Statement (oss); And If Applicable, Original Notarized Secretary’s Certificate In Case Of A Corporation, Partnership, Or Cooperative; Or Original Special Power Of Attorney Of All Members Of The Joint Venture Giving Full Power And Authority To Its Officer To Sign The Oss And Do Acts To Represent The Bidder. Financial Documents ⬜ (h) The Prospective Bidder’s Computation Of Net Financial Contracting Capacity (nfcc). Class “b” Documents ⬜ (i) If Applicable, Duly Signed Joint Venture Agreement (jva) In Accordance With Ra No. 4566 And Its Irr In Case The Joint Venture Is Already In Existence; Or Duly Notarized Statements From All The Potential Joint Venture Partners Stating That They Will Enter Into And Abide By The Provisions Of The Jva In The Instance That The Bid Is Successful. Ii. Financial Component Envelope ⬜ (j) Original Of Duly Signed And Accomplished Financial Bid Form; And Other Documentary Requirements Under Ra No. 9184 ⬜ (k) Original Of Duly Signed Bid Prices In The Bill Of Quantities; And ⬜ (l) Duly Accomplished Detailed Estimates Form, Including A Summary Sheet Indicating The Unit Prices Of Construction Materials, Labor Rates, And Equipment Rentals Used In Coming Up With The Bid; And ⬜ Cash Flow By Quarter. Bid Form For The Procurement Of Infrastructure Projects [shall Be Submitted With The Bid] Bid Form Date : Project Identification No. : To: [name And Address Of Procuring Entity] Having Examined The Philippine Bidding Documents (pbds) Including The Supplemental Or Bid Bulletin Numbers [insert Numbers], The Receipt Of Which Is Hereby Duly Acknowledged, We, The Undersigned, Declare That: A. We Have No Reservation To The Pbds, Including The Supplemental Or Bid Bulletins, For The Procurement Project: [insert Name Of Contract]; B. We Offer To Execute The Works For This Contract In Accordance With The Pbds; C. The Total Price Of Our Bid In Words And Figures, Excluding Any Discounts Offered Below Is: [insert Information]; D. The Discounts Offered And The Methodology For Their Application Are: [insert Information]; E. The Total Bid Price Includes The Cost Of All Taxes, Such As, But Not Limited To: [specify The Applicable Taxes, E.g. (i) Value Added Tax (vat), (ii) Income Tax, (iii) Local Taxes, And (iv) Other Fiscal Levies And Duties], Which Are Itemized Herein And Reflected In The Detailed Estimates, F. Our Bid Shall Be Valid Within The Period Stated In The Pbds, And It Shall Remain Binding Upon Us At Any Time Before The Expiration Of That Period; G. If Our Bid Is Accepted, We Commit To Obtain A Performance Security In The Amount Of [insert Percentage Amount] Percent Of The Contract Price For The Due Performance Of The Contract, Or A Performance Securing Declaration In Lieu Of The The Allowable Forms Of Performance Security, Subject To The Terms And Conditions Of Issued Gppb Guidelines12 For This Purpose; H. We Are Not Participating, As Bidders, In More Than One Bid In This Bidding Process, Other Than Alternative Offers In Accordance With The Bidding Documents; I. We Understand That This Bid, Together With Your Written Acceptance Thereof Included In Your Notification Of Award, Shall Constitute A Binding Contract Between Us, Until A Formal Contract Is Prepared And Executed; And J. We Understand That You Are Not Bound To Accept The Lowest Calculated Bid Or Any Other Bid That You May Receive. K. We Likewise Certify/confirm That The Undersigned, Is The Duly Authorized Representative Of The Bidder, And Granted Full Power And Authority To Do, Execute 12 Currently Based On Gppb Resolution No. 09-2020 And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For The [name Of Project] Of The [name Of The Procuring Entity]. L. We Acknowledge That Failure To Sign Each And Every Page Of This Bid Form, Including The Bill Of Quantities, Shall Be A Ground For The Rejection Of Our Bid. Name: Legal Capacity: Signature: Duly Authorized To Sign The Bid For And Behalf Of: Date: Bid Securing Declaration Form [shall Be Submitted With The Bid If Bidder Opts To Provide This Form Of Bid Security] Republic Of The Philippines) City Of ) S.s. Bid Securing Declaration Project Identification No.: [insert Number] To: [insert Name And Address Of The Procuring Entity] I/we, The Undersigned, Declare That: 1. I/we Understand That, According To Your Conditions, Bids Must Be Supported By A Bid Security, Which May Be In The Form Of A Bid Securing Declaration. 2. I/we Accept That: (a) I/we Will Be Automatically Disqualified From Bidding For Any Procurement Contract With Any Procuring Entity For A Period Of Two (2) Years Upon Receipt Of Your Blacklisting Order; And, (b) I/we Will Pay The Applicable Fine Provided Under Section 6 Of The Guidelines On The Use Of Bid Securing Declaration, Within Fifteen (15) Days From Receipt Of The Written Demand By The Procuring Entity For The Commission Of Acts Resulting To The Enforcement Of The Bid Securing Declaration Under Sections 23.1(b), 34.2, 40.1 And 69.1, Except 69.1(f),of The Irr Of Ra No. 9184; Without Prejudice To Other Legal Action The Government May Undertake. 3. I/we Understand That This Bid Securing Declaration Shall Cease To Be Valid On The Following Circumstances: A. Upon Expiration Of The Bid Validity Period, Or Any Extension Thereof Pursuant To Your Request; B. I Am/we Are Declared Ineligible Or Post-disqualified Upon Receipt Of Your Notice To Such Effect, And (i) I/we Failed To Timely File A Request For Reconsideration Or (ii) I/we Filed A Waiver To Avail Of Said Right; And C. I Am/we Are Declared The Bidder With The Lowest Calculated Responsive Bid, And I/we Have Furnished The Performance Security And Signed The Contract. In Witness Whereof, I/we Have Hereunto Set My/our Hand/s This Day Of [month] [year] At [place Of Execution]. [insert Name Of Bidder Or Its Authorized Representative] [insert Signatory’s Legal Capacity] Affiant [jurat] [format Shall Be Based On The Latest Rules On Notarial Practice] Omnibus Sworn Statement (revised) [shall Be Submitted With The Bid] Republic Of The Philippines ) City/municipality Of ) S.s. Affidavit I, [name Of Affiant], Of Legal Age, [civil Status], [nationality], And Residing At [address Of Affiant], After Having Been Duly Sworn In Accordance With Law, Do Hereby Depose And State That: 1. [select One, Delete The Other:] [if A Sole Proprietorship:] I Am The Sole Proprietor Or Authorized Representative Of [name Of Bidder] With Office Address At [address Of Bidder]; [if A Partnership, Corporation, Cooperative, Or Joint Venture:] I Am The Duly Authorized And Designated Representative Of [name Of Bidder] With Office Address At [address Of Bidder]; 2. [select One, Delete The Other:] [if A Sole Proprietorship:] As The Owner And Sole Proprietor, Or Authorized Representative Of [name Of Bidder], I Have Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For [name Of The Project] Of The [name Of The Procuring Entity], As Shown In The Attached Duly Notarized Special Power Of Attorney; [if A Partnership, Corporation, Cooperative, Or Joint Venture:] I Am Granted Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For [name Of The Project] Of The [name Of The Procuring Entity], As Shown In The Attached [state Title Of Attached Document Showing Proof Of Authorization (e.g., Duly Notarized Secretary’s Certificate, Board/partnership Resolution, Or Special Power Of Attorney, Whichever Is Applicable;)]; 3. [name Of Bidder] Is Not “blacklisted” Or Barred From Bidding By The Government Of The Philippines Or Any Of Its Agencies, Offices, Corporations, Or Local Government Units, Foreign Government/foreign Or International Financing Institution Whose Blacklisting Rules Have Been Recognized By The Government Procurement Policy Board, By Itself Or By Relation, Membership, Association, Affiliation, Or Controlling Interest With Another Blacklisted Person Or Entity As Defined And Provided For In The Uniform Guidelines On Blacklisting; 4. Each Of The Documents Submitted In Satisfaction Of The Bidding Requirements Is An Authentic Copy Of The Original, Complete, And All Statements And Information Provided Therein Are True And Correct; 5. [name Of Bidder] Is Authorizing The Head Of The Procuring Entity Or Its Duly Authorized Representative(s) To Verify All The Documents Submitted; 6. [select One, Delete The Rest:] [if A Sole Proprietorship:] The Owner Or Sole Proprietor Is Not Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; [if A Partnership Or Cooperative:] None Of The Officers And Members Of [name Of Bidder] Is Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; [if A Corporation Or Joint Venture:] None Of The Officers, Directors, And Controlling Stockholders Of [name Of Bidder] Is Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; 7. [name Of Bidder] Complies With Existing Labor Laws And Standards; And 8. [name Of Bidder] Is Aware Of And Has Undertaken The Responsibilities As A Bidder In Compliance With The Philippine Bidding Documents, Which Includes: A. Carefully Examining All Of The Bidding Documents; B. Acknowledging All Conditions, Local Or Otherwise, Affecting The Implementation Of The Contract; C. Making An Estimate Of The Facilities Available And Needed For The Contract To Be Bid, If Any; And D. Inquiring Or Securing Supplemental/bid Bulletin(s) Issued For The [name Of The Project]. 9. [name Of Bidder] Did Not Give Or Pay Directly Or Indirectly, Any Commission, Amount, Fee, Or Any Form Of Consideration, Pecuniary Or Otherwise, To Any Person Or Official, Personnel Or Representative Of The Government In Relation To Any Procurement Project Or Activity. 10. In Case Advance Payment Was Made Or Given, Failure To Perform Or Deliver Any Of The Obligations And Undertakings In The Contract Shall Be Sufficient Grounds To Constitute Criminal Liability For Swindling (estafa) Or The Commission Of Fraud With Unfaithfulness Or Abuse Of Confidence Through Misappropriating Or Converting Any Payment Received By A Person Or Entity Under An Obligation Involving The Duty To Deliver Certain Goods Or Services, To The Prejudice Of The Public And The Government Of The Philippines Pursuant To Article 315 Of Act No. 3815 S. 1930, As Amended, Or The Revised Penal Code. In Witness Whereof, I Have Hereunto Set My Hand This Day Of , 20 At , Philippines. [insert Name Of Bidder Or Its Authorized Representative] [insert Signatory’s Legal Capacity] Affiant [jurat] [format Shall Be Based On The Latest Rules On Notarial Practice]

Details: Description Philippine Bidding Documents (as Harmonized With Development Partners) Construction Of Warehouse At Art Center, Brgy. Nanga, Pototan, Iloilo Bid No. Agr-24-1528-b Iloilo Provincial Government Table Of Contents Glossary Of Terms, Abbreviations, And Acronyms 4 Section I. Invitation To Bid 7 Section Ii. Instructions To Bidders 9 1. Scope Of Bid 9 2. Funding Information 9 3. Bidding Requirements 9 4. Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices 9 5. Eligible Bidders 10 6. Origin Of Associated Goods 10 7. Subcontracts 10 8. Pre-bid Conference 10 9. Clarification And Amendment Of Bidding Documents 10 10. Documents Comprising The Bid: Eligibility And Technical Components 11 11. Documents Comprising The Bid: Financial Component 11 12. Alternative Bids 11 13. Bid Prices 11 14. Bid And Payment Currencies 12 15. Bid Security 12 16. Sealing And Marking Of Bids 12 17. Deadline For Submission Of Bids 12 18. Opening And Preliminary Examination Of Bids 12 19. Detailed Evaluation And Comparison Of Bids 13 20. Post Qualification 13 21. Signing Of The Contract 13 Section Iii. Bid Data Sheet 14 Section Iv. General Conditions Of Contract 16 1. Scope Of Contract 16 2. Sectional Completion Of Works 16 3. Possession Of Site 16 4. The Contractor’s Obligations 16 5. Performance Security 17 6. Site Investigation Reports 17 7. Warranty 17 8. Liability Of The Contractor 17 9. Termination For Other Causes 17 10. Dayworks 18 11. Program Of Work 18 12. Instructions, Inspections And Audits 18 13. Advance Payment 18 14. Progress Payments 18 15. Operating And Maintenance Manuals 18 Section V. Special Conditions Of Contract 20 Section Vi. Specifications 21 Section Vii. Drawings 25 Section Viii. Bill Of Quantities 31 Section Ix. Checklist Of Technical And Financial Documents 39 Glossary Of Terms, Abbreviations, And Acronyms Abc – Approved Budget For The Contract. Arcc – Allowable Range Of Contract Cost. Bac – Bids And Awards Committee. Bid – A Signed Offer Or Proposal To Undertake A Contract Submitted By A Bidder In Response To And In Consonance With The Requirements Of The Bidding Documents. Also Referred To As Proposal And Tender. (2016 Revised Irr, Section 5[c]) Bidder – Refers To A Contractor, Manufacturer, Supplier, Distributor And/or Consultant Who Submits A Bid In Response To The Requirements Of The Bidding Documents. (2016 Revised Irr, Section 5[d]) Bidding Documents – The Documents Issued By The Procuring Entity As The Bases For Bids, Furnishing All Information Necessary For A Prospective Bidder To Prepare A Bid For The Goods, Infrastructure Projects, And/or Consulting Services Required By The Procuring Entity. (2016 Revised Irr, Section 5[e]) Bir – Bureau Of Internal Revenue. Bsp – Bangko Sentral Ng Pilipinas. Cda – Cooperative Development Authority. Consulting Services – Refer To Services For Infrastructure Projects And Other Types Of Projects Or Activities Of The Gop Requiring Adequate External Technical And Professional Expertise That Are Beyond The Capability And/or Capacity Of The Gop To Undertake Such As, But Not Limited To: (i) Advisory And Review Services; (ii) Pre-investment Or Feasibility Studies; (iii) Design; (iv) Construction Supervision; (v) Management And Related Services; And (vi) Other Technical Services Or Special Studies. (2016 Revised Irr, Section 5[i]) Contract – Refers To The Agreement Entered Into Between The Procuring Entity And The Supplier Or Manufacturer Or Distributor Or Service Provider For Procurement Of Goods And Services; Contractor For Procurement Of Infrastructure Projects; Or Consultant Or Consulting Firm For Procurement Of Consulting Services; As The Case May Be, As Recorded In The Contract Form Signed By The Parties, Including All Attachments And Appendices Thereto And All Documents Incorporated By Reference Therein. Contractor – Is A Natural Or Juridical Entity Whose Proposal Was Accepted By The Procuring Entity And To Whom The Contract To Execute The Work Was Awarded. Contractor As Used In These Bidding Documents May Likewise Refer To A Supplier, Distributor, Manufacturer, Or Consultant. Cpi – Consumer Price Index. Dole – Department Of Labor And Employment. Dti – Department Of Trade And Industry. Foreign-funded Procurement Or Foreign-assisted Project – Refers To Procurement Whose Funding Source Is From A Foreign Government, Foreign Or International Financing Institution As Specified In The Treaty Or International Or Executive Agreement. (2016 Revised Irr, Section 5[b]). Gfi – Government Financial Institution. Gocc – Government-owned And/or –controlled Corporation. Goods – Refer To All Items, Supplies, Materials And General Support Services, Except Consulting Services And Infrastructure Projects, Which May Be Needed In The Transaction Of Public Businesses Or In The Pursuit Of Any Government Undertaking, Project Or Activity, Whether In The Nature Of Equipment, Furniture, Stationery, Materials For Construction, Or Personal Property Of Any Kind, Including Non-personal Or Contractual Services Such As The Repair And Maintenance Of Equipment And Furniture, As Well As Trucking, Hauling, Janitorial, Security, And Related Or Analogous Services, As Well As Procurement Of Materials And Supplies Provided By The Procuring Entity For Such Services. The Term “related” Or “analogous Services” Shall Include, But Is Not Limited To, Lease Or Purchase Of Office Space, Media Advertisements, Health Maintenance Services, And Other Services Essential To The Operation Of The Procuring Entity. (2016 Revised Irr, Section 5[r]) Gop – Government Of The Philippines. Infrastructure Projects – Include The Construction, Improvement, Rehabilitation, Demolition, Repair, Restoration Or Maintenance Of Roads And Bridges, Railways, Airports, Seaports, Communication Facilities, Civil Works Components Of Information Technology Projects, Irrigation, Flood Control And Drainage, Water Supply, Sanitation, Sewerage And Solid Waste Management Systems, Shore Protection, Energy/power And Electrification Facilities, National Buildings, School Buildings, Hospital Buildings, And Other Related Construction Projects Of The Government. Also Referred To As Civil Works Or Works. (2016 Revised Irr, Section 5[u]) Lgus – Local Government Units. Nfcc – Net Financial Contracting Capacity. Nga – National Government Agency. Pcab – Philippine Contractors Accreditation Board. Philgeps - Philippine Government Electronic Procurement System. Procurement Project – Refers To A Specific Or Identified Procurement Covering Goods, Infrastructure Project Or Consulting Services. A Procurement Project Shall Be Described, Detailed, And Scheduled In The Project Procurement Management Plan Prepared By The Agency Which Shall Be Consolidated In The Procuring Entity's Annual Procurement Plan. (gppb Circular No. 06-2019 Dated 17 July 2019) Psa – Philippine Statistics Authority. Sec – Securities And Exchange Commission. Slcc – Single Largest Completed Contract. Un – United Nations. Republic Of The Philippines Iloilo Provincial Government Section I. Invitation To Bid For Construction Of Warehouse At Art Center, Brgy. Nanga, Pototan, Iloilo Bid No. Agr-24-1528-b 1. The Iloilo Provincial Government, Through The 20% Nta Development Fund – Fy 2024 – Buildings Intends To Apply The Sum Of Twenty Million Pesos (p 20,000,000.00) Being The Approved Budget For The Contract (abc) To Payments Under The Contract For Agr-24-1528-b For The Construction Of Warehouse At Art Center, Brgy. Nanga, Pototan, Iloilo For The Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. 2. The Iloilo Provincial Government Now Invites Bids For The Above Procurement Project. Completion Of The Works Is Required One Eighty 180 Calendar Days. Bidders Should Have Completed A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii (instructions To Bidders). 3. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) No. 9184. 4. Interested Bidders May Obtain Further Information From The Bids And Awards Committee Secretariat, 5th Floor, New Iloilo Provincial Capitol, Bonifacio Drive, Iloilo City, Philippines And Inspect The Bidding Documents At The Address Given Below From 8:00am To 5:00pm. 5. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders On October 10, 2024 From Given Address And Website/s Below And Upon Payment Of The Applicable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb, In The Amount Of Ten Thousand Pesos (p10, 000.00). The Procuring Entity Shall Allow The Bidder To Present Its Proof Of Payment For The Fees In Person. 6. The Iloilo Provincial Government Will Hold A Pre-bid Conference On October 17, 2024, 9:00 A.m. At Bids And Awards Committee Secretariat, 5th Floor, New Iloilo Provincial Capitol, Bonifacio Drive, Iloilo City, Philippines, And/or Through Videoconferencing/webcasting Via Zoom Conference Which Shall Be Open To Prospective Bidders. The Default Meeting Id And Password Shall Be: Meeting Id: 4340851724 // Password: 0922 7. Bids Must Be Duly Received By The Bac Secretariat Through Manual Submission At The Office Address At Ground Floor, Lobby, Iloilo Provincial Capitol, Iloilo City On Or Before October 29, 2024, 9:00 A.m.. Late Bids Shall Not Be Accepted. 8. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 16. 9. Bid Opening Shall Be On October 29, 2024, 9:00 A.m. At Bids And Awards Committee Secretariat, 5th Floor, New Iloilo Provincial Capitol, Bonifacio Drive, Iloilo City, Philippines. Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend The Activity. 10. The Iloilo Provincial Government Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Implementing Rules And Regulations (irr) Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 11. For Further Information, Please Refer To: Atty. Raemman M. Lagrada Head, Bac Secretariat 5f New Iloilo Provincial Capitol Bonifacio Drive, Iloilo City Tel. No. (33) 336-0736 Fax No. (33) 337-7731 Email: Ipg_bacs@yahoo.com 12. You May Visit The Following Websites: For Downloading Of Bidding Documents: Www.iloilo.gov.ph October 8, 2024 Atty. Dennis T. Ventilacion Bac Chairperson Section Ii. Instructions To Bidders 1. Scope Of Bid The Procuring Entity, Iloilo Provincial Government Invites Bids For The Construction Of Warehouse At Art Center, Brgy. Nanga, Pototan, Iloilo, With Project Identification Number Agr-24-1528-b. The Procurement Project (referred To Herein As “project”) Is For The Construction Of Works, As Described In Section Vi (specifications). 2. Funding Information 2.1. The Gop Through The Source Of Funding As Indicated Below For 2024 In The Amount Of Twenty Million Pesos (p 20,000,000.00) 2.2. The Source Of Funding Is: A. 20% Nta Development Fund – Fy 2024 – Buildings 3. Bidding Requirements The Bidding For The Project Shall Be Governed By All The Provisions Of Ra No. 9184 And Its 2016 Revised Irr, Including Its Generic Procurement Manual And Associated Policies, Rules And Regulations As The Primary Source Thereof, While The Herein Clauses Shall Serve As The Secondary Source Thereof. Any Amendments Made To The Irr And Other Gppb Issuances Shall Be Applicable Only To The Ongoing Posting, Advertisement, Or Invitation To Bid By The Bac Through The Issuance Of A Supplemental Or Bid Bulletin. The Bidder, By The Act Of Submitting Its Bid, Shall Be Deemed To Have Inspected The Site, Determined The General Characteristics Of The Contracted Works And The Conditions For This Project, Such As The Location And The Nature Of The Work; (b) Climatic Conditions; (c) Transportation Facilities; (c) Nature And Condition Of The Terrain, Geological Conditions At The Site Communication Facilities, Requirements, Location And Availability Of Construction Aggregates And Other Materials, Labor, Water, Electric Power And Access Roads; And (d) Other Factors That May Affect The Cost, Duration And Execution Or Implementation Of The Contract, Project, Or Work And Examine All Instructions, Forms, Terms, And Project Requirements In The Bidding Documents. 4. Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices The Procuring Entity, As Well As The Bidders And Contractors, Shall Observe The Highest Standard Of Ethics During The Procurement And Execution Of The Contract. They Or Through An Agent Shall Not Engage In Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices Defined Under Annex “i” Of The 2016 Revised Irr Of Ra No. 9184 Or Other Integrity Violations In Competing For The Project. 5. Eligible Bidders 5.1. Only Bids Of Bidders Found To Be Legally, Technically, And Financially Capable Will Be Evaluated. 5.2. The Bidder Must Have An Experience Of Having Completed A Single Largest Completed Contract (slcc) That Is Similar To This Project, Equivalent To At Least Fifty Percent (50%) Of The Abc Adjusted, If Necessary, By The Bidder To Current Prices Using The Psa’s Cpi, Except Under Conditions Provided For In Section 23.4.2.4 Of The 2016 Revised Irr Of Ra No. 9184. A Contract Is Considered To Be “similar” To The Contract To Be Bid If It Has The Major Categories Of Work Stated In The Bds. 5.3. For Foreign-funded Procurement, The Procuring Entity And The Foreign Government/foreign Or International Financing Institution May Agree On Another Track Record Requirement, As Specified In The Bidding Document Prepared For This Purpose. 5.4. The Bidders Shall Comply With The Eligibility Criteria Under Section 23.4.2 Of The 2016 Irr Of Ra No. 9184. 6. Origin Of Associated Goods There Is No Restriction On The Origin Of Goods Other Than Those Prohibited By A Decision Of The Un Security Council Taken Under Chapter Vii Of The Charter Of The Un. 7. Subcontracts 7.1. The Bidder May Subcontract Portions Of The Project To The Extent Allowed By The Procuring Entity As Stated Herein, But In No Case More Than Fifty Percent (50%) Of The Project. The Procuring Entity Has Prescribed That: A. Subcontracting Is Not Allowed. 8. Pre-bid Conference The Procuring Entity Will Hold A Pre-bid Conference For This Project On The Specified Date And Time And Either At Its Physical Address At Bac Office, 5th Floor, New Iloilo Provincial Capitol, Iloilo City And/or Through Videoconferencing As Indicated In Paragraph 6 Of The Ib. 9. Clarification And Amendment Of Bidding Documents Prospective Bidders May Request For Clarification On And/or Interpretation Of Any Part Of The Bidding Documents. Such Requests Must Be In Writing And Received By The Procuring Entity, Either At Its Given Address Or Through Electronic Mail Indicated In The Ib, At Least Ten (10) Calendar Days Before The Deadline Set For The Submission And Receipt Of Bids. 10. Documents Comprising The Bid: Eligibility And Technical Components 10.1. The First Envelope Shall Contain The Eligibility And Technical Documents Of The Bid As Specified In Section Ix. Checklist Of Technical And Financial Documents. 10.2. If The Eligibility Requirements Or Statements, The Bids, And All Other Documents For Submission To The Bac Are In Foreign Language Other Than English, It Must Be Accompanied By A Translation In English, Which Shall Be Authenticated By The Appropriate Philippine Foreign Service Establishment, Post, Or The Equivalent Office Having Jurisdiction Over The Foreign Bidder’s Affairs In The Philippines. For Contracting Parties To The Apostille Convention, Only The Translated Documents Shall Be Authenticated Through An Apostille Pursuant To Gppb Resolution No. 13-2019 Dated 23 May 2019. The English Translation Shall Govern, For Purposes Of Interpretation Of The Bid. 10.3. In Joint Ventures, A Special Pcab License, And Registration For The Type And Cost Of The Contract For This Project, Shall Be Required. Any Additional Type Of Contractor License Or Permit Shall Be Indicated In The Bds. 10.4. A List Of Contractor’s Key Personnel (e.g., Project Manager, Project Engineers, Materials Engineers, And Foremen) Assigned To The Contract To Be Bid, With Their Complete Qualification And Experience Data Shall Be Provided. These Key Personnel Must Meet The Required Minimum Years Of Experience Set In The Bds. 10.5. A List Of Contractor’s Major Equipment Units, Which Are Owned, Leased, And/or Under Purchase Agreements, Supported By Proof Of Ownership, Certification Of Availability Of Equipment From The Equipment Lessor/vendor For The Duration Of The Project, As The Case May Be, Must Meet The Minimum Requirements For The Contract Set In The Bds. 11. Documents Comprising The Bid: Financial Component 11.1. The Second Bid Envelope Shall Contain The Financial Documents For The Bid As Specified In Section Ix. Checklist Of Technical And Financial Documents. 11.2. Any Bid Exceeding The Abc Indicated In Paragraph 1 Of The Ib Shall Not Be Accepted. 11.3. For Foreign-funded Procurement, A Ceiling May Be Applied To Bid Prices Provided The Conditions Are Met Under Section 31.2 Of The 2016 Revised Irr Of Ra No. 9184. 12. Alternative Bids Bidders Shall Submit Offers That Comply With The Requirements Of The Bidding Documents, Including The Basic Technical Design As Indicated In The Drawings And Specifications. Unless There Is A Value Engineering Clause In The Bds, Alternative Bids Shall Not Be Accepted. 13. Bid Prices All Bid Prices For The Given Scope Of Work In The Project As Awarded Shall Be Considered As Fixed Prices, And Therefore Not Subject To Price Escalation During Contract Implementation, Except Under Extraordinary Circumstances As Determined By The Neda And Approved By The Gppb Pursuant To The Revised Guidelines For Contract Price Escalation Guidelines. 14. Bid And Payment Currencies 14.1. Bid Prices May Be Quoted In The Local Currency Or Tradeable Currency Accepted By The Bsp At The Discretion Of The Bidder. However, For Purposes Of Bid Evaluation, Bids Denominated In Foreign Currencies Shall Be Converted To Philippine Currency Based On The Exchange Rate As Published In The Bsp Reference Rate Bulletin On The Day Of The Bid Opening. 14.2. Payment Of The Contract Price Shall Be Made In: A. Philippine Pesos. 15. Bid Security 15.1. The Bidder Shall Submit A Bid Securing Declaration Or Any Form Of Bid Security In The Amount Indicated In The Bds, Which Shall Be Not Less Than The Percentage Of The Abc In Accordance With The Schedule In The Bds. 15.2. The Bid And Bid Security Shall Be Valid Until February 6, 2025. Any Bid Not Accompanied By An Acceptable Bid Security Shall Be Rejected By The Procuring Entity As Non-responsive. 16. Sealing And Marking Of Bids Each Bidder Shall Submit One Copy Of The First And Second Components Of Its Bid. The Procuring Entity May Request Additional Hard Copies And/or Electronic Copies Of The Bid. However, Failure Of The Bidders To Comply With The Said Request Shall Not Be A Ground For Disqualification. If The Procuring Entity Allows The Submission Of Bids Through Online Submission To The Given Website Or Any Other Electronic Means, The Bidder Shall Submit An Electronic Copy Of Its Bid, Which Must Be Digitally Signed. An Electronic Copy That Cannot Be Opened Or Is Corrupted Shall Be Considered Non-responsive And, Thus, Automatically Disqualified. 17. Deadline For Submission Of Bids The Bidders Shall Submit On The Specified Date And Time And Either At Its Physical Address Or Through Online Submission As Indicated In Paragraph 7 Of The Ib. 18. Opening And Preliminary Examination Of Bids 18.1. The Bac Shall Open The Bids In Public At The Time, On The Date, And At The Place Specified In Paragraph 9 Of The Ib. The Bidders’ Representatives Who Are Present Shall Sign A Register Evidencing Their Attendance. In Case Videoconferencing, Webcasting Or Other Similar Technologies Will Be Used, Attendance Of Participants Shall Likewise Be Recorded By The Bac Secretariat. In Case The Bids Cannot Be Opened As Scheduled Due To Justifiable Reasons, The Rescheduling Requirements Under Section 29 Of The 2016 Revised Irr Of Ra No. 9184 Shall Prevail. 18.2. The Preliminary Examination Of Bids Shall Be Governed By Section 30 Of The 2016 Revised Irr Of Ra No. 9184. 19. Detailed Evaluation And Comparison Of Bids 19.1. The Procuring Entity’s Bac Shall Immediately Conduct A Detailed Evaluation Of All Bids Rated “passed” Using Non-discretionary Pass/fail Criteria. The Bac Shall Consider The Conditions In The Evaluation Of Bids Under Section 32.2 Of 2016 Revised Irr Of Ra No. 9184. 19.2. If The Project Allows Partial Bids, All Bids And Combinations Of Bids As Indicated In The Bds Shall Be Received By The Same Deadline And Opened And Evaluated Simultaneously So As To Determine The Bid Or Combination Of Bids Offering The Lowest Calculated Cost To The Procuring Entity. Bid Security As Required By Itb Clause 16 Shall Be Submitted For Each Contract (lot) Separately. 19.3. In All Cases, The Nfcc Computation Pursuant To Section 23.4.2.6 Of The 2016 Revised Irr Of Ra No. 9184 Must Be Sufficient For The Total Of The Abcs For All The Lots Participated In By The Prospective Bidder. 20. Post Qualification Within A Non-extendible Period Of Five (5) Calendar Days From Receipt By The Bidder Of The Notice From The Bac That It Submitted The Lowest Calculated Bid, The Bidder Shall Submit Its Latest Income And Business Tax Returns Filed And Paid Through The Bir Electronic Filing And Payment System (efps), And Other Appropriate Licenses And Permits Required By Law And Stated In The Bds. 21. Signing Of The Contract The Documents Required In Section 37.2 Of The 2016 Revised Irr Of Ra No. 9184 Shall Form Part Of The Contract. Additional Contract Documents Are Indicated In The Bds. Section Iii. Bid Data Sheet Itb Clause 5.2 For This Purpose, Contracts Similar To The Project Refer To Contracts Which Have The Same Major Categories Of Work, Which Shall Be: A) Construction Of Warehouse/buildings 7.1 The Procuring Entity Has Prescribed That Subcontracting Is Not Allowed. 10.3 [specify If Another Contractor License Or Permit Is Required.] 10.4 The Key Personnel Must Meet The Required Minimum Years Of Experience Set Below: Key Personnel General Experience Relevant Experience 1-project Engineer 1 Year 1 Year 1-materials Engineer 1 Year 1 Year 1-agricultural And Biosystems Engineer 1 Year 1 Year 1-health & Safety Officer 1 Year 1 Year 1-foreman 1 Year 1 Year 1-carpenter 1 Year 1 Year 1-steelman 1 Year 1 Year 1-mason 1 Year 1 Year 1-welder 1 Year 1 Year 1-electrician 1 Year 1 Year 1-plumber 1 Year 1 Year 1-painter 1 Year 1 Year 10.5 The Minimum Major Equipment Requirements Are The Following: Equipment Capacity Number Of Units Dump Truck - 1 Chainsaw - 1 Backhoe - 1 Pneumatic Tire Roller - 1 One Bagger Mixer - 1 Bar Cutter - 1 Welding Machine - 1 Electric Drill - 1 12 Alternative Bids Are Not Allowed 15.1 The Bid Security Shall Be In The Form Of A Bid Securing Declaration Or Any Of The Following Forms And Amounts: A. The Amount Of Not Less Than Two Percent (2%) Of Abc, If Bid Security Is In Cash, Cashier’s/manager’s Check, Bank Draft/guarantee Or Irrevocable Letter Of Credit; B. The Amount Of Not Less Than Five Percent (5%) Of Abc If Bid Security Is In Surety Bond. 19.2 Partial Bid Is Not Allowed 20 No Further Instructions. 21 The Additional Contract Documents Relevant To The Project That Are Required By The Procuring Entity Are: A. Construction Schedule And S-curve; B. Manpower Schedule; C. Construction Methods; D. Equipment Utilization Schedule; E. Construction Safety And Health Program Approved By The Department Of Labor And Employment; And F. Pert/cpm Section Iv. General Conditions Of Contract 1. Scope Of Contract This Contract Shall Include All Such Items, Although Not Specifically Mentioned, That Can Be Reasonably Inferred As Being Required For Its Completion As If Such Items Were Expressly Mentioned Herein. All The Provisions Of Ra No. 9184 And Its 2016 Revised Irr, Including The Generic Procurement Manual, And Associated Issuances, Constitute The Primary Source For The Terms And Conditions Of The Contract, And Thus, Applicable In Contract Implementation. Herein Clauses Shall Serve As The Secondary Source For The Terms And Conditions Of The Contract. This Is Without Prejudice To Sections 74.1 And 74.2 Of The 2016 Revised Irr Of Ra No. 9184 Allowing The Gppb To Amend The Irr, Which Shall Be Applied To All Procurement Activities, The Advertisement, Posting, Or Invitation Of Which Were Issued After The Effectivity Of The Said Amendment. 2. Sectional Completion Of Works If Sectional Completion Is Specified In The Special Conditions Of Contract (scc), References In The Conditions Of Contract To The Works, The Completion Date, And The Intended Completion Date Shall Apply To Any Section Of The Works (other Than References To The Completion Date And Intended Completion Date For The Whole Of The Works). 3. Possession Of Site 4.1. The Procuring Entity Shall Give Possession Of All Or Parts Of The Site To The Contractor Based On The Schedule Of Delivery Indicated In The Scc, Which Corresponds To The Execution Of The Works. If The Contractor Suffers Delay Or Incurs Cost From Failure On The Part Of The Procuring Entity To Give Possession In Accordance With The Terms Of This Clause, The Procuring Entity’s Representative Shall Give The Contractor A Contract Time Extension And Certify Such Sum As Fair To Cover The Cost Incurred, Which Sum Shall Be Paid By Procuring Entity. 4.2. If Possession Of A Portion Is Not Given By The Above Date, The Procuring Entity Will Be Deemed To Have Delayed The Start Of The Relevant Activities. The Resulting Adjustments In Contract Time To Address Such Delay May Be Addressed Through Contract Extension Provided Under Annex “e” Of The 2016 Revised Irr Of Ra No. 9184. 4. The Contractor’s Obligations The Contractor Shall Employ The Key Personnel Named In The Schedule Of Key Personnel Indicating Their Designation, In Accordance With Itb Clause 10.3 And Specified In The Bds, To Carry Out The Supervision Of The Works. The Procuring Entity Will Approve Any Proposed Replacement Of Key Personnel Only If Their Relevant Qualifications And Abilities Are Equal To Or Better Than Those Of The Personnel Listed In The Schedule. 5. Performance Security 5.1. Within Ten (10) Calendar Days From Receipt Of The Notice Of Award From The Procuring Entity But In No Case Later Than The Signing Of The Contract By Both Parties, The Successful Bidder Shall Furnish The Performance Security In Any Of The Forms Prescribed In Section 39 Of The 2016 Revised Irr. 5.2. The Contractor, By Entering Into The Contract With The Procuring Entity, Acknowledges The Right Of The Procuring Entity To Institute Action Pursuant To Ra No. 3688 Against Any Subcontractor Be They An Individual, Firm, Partnership, Corporation, Or Association Supplying The Contractor With Labor, Materials And/or Equipment For The Performance Of This Contract. 6. Site Investigation Reports The Contractor, In Preparing The Bid, Shall Rely On Any Site Investigation Reports Referred To In The Scc Supplemented By Any Information Obtained By The Contractor. 7. Warranty 7.1. In Case The Contractor Fails To Undertake The Repair Works Under Section 62.2.2 Of The 2016 Revised Irr, The Procuring Entity Shall Forfeit Its Performance Security, Subject Its Property(ies) To Attachment Or Garnishment Proceedings, And Perpetually Disqualify It From Participating In Any Public Bidding. All Payables Of The Gop In His Favor Shall Be Offset To Recover The Costs. 7.2. The Warranty Against Structural Defects/failures, Except That Occasioned-on Force Majeure, Shall Cover The Period From The Date Of Issuance Of The Certificate Of Final Acceptance By The Procuring Entity. Specific Duration Of The Warranty Is Found In The Scc. 8. Liability Of The Contractor Subject To Additional Provisions, If Any, Set Forth In The Scc, The Contractor’s Liability Under This Contract Shall Be As Provided By The Laws Of The Republic Of The Philippines. If The Contractor Is A Joint Venture, All Partners To The Joint Venture Shall Be Jointly And Severally Liable To The Procuring Entity. 9. Termination For Other Causes Contract Termination Shall Be Initiated In Case It Is Determined Prima Facie By The Procuring Entity That The Contractor Has Engaged, Before, Or During The Implementation Of The Contract, In Unlawful Deeds And Behaviors Relative To Contract Acquisition And Implementation, Such As, But Not Limited To Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices As Stated In Itb Clause 4. 10. Dayworks Subject To The Guidelines On Variation Order In Annex “e” Of The 2016 Revised Irr Of Ra No. 9184, And If Applicable As Indicated In The Scc, The Dayworks Rates In The Contractor’s Bid Shall Be Used For Small Additional Amounts Of Work Only When The Procuring Entity’s Representative Has Given Written Instructions In Advance For Additional Work To Be Paid For In That Way. 11. Program Of Work 11.1. The Contractor Shall Submit To The Procuring Entity’s Representative For Approval The Said Program Of Work Showing The General Methods, Arrangements, Order, And Timing For All The Activities In The Works. The Submissions Of The Program Of Work Are Indicated In The Scc. 11.2. The Contractor Shall Submit To The Procuring Entity’s Representative For Approval An Updated Program Of Work At Intervals No Longer Than The Period Stated In The Scc. If The Contractor Does Not Submit An Updated Program Of Work Within This Period, The Procuring Entity’s Representative May Withhold The Amount Stated In The Scc From The Next Payment Certificate And Continue To Withhold This Amount Until The Next Payment After The Date On Which The Overdue Program Of Work Has Been Submitted. 12. Instructions, Inspections And Audits The Contractor Shall Permit The Gop Or The Procuring Entity To Inspect The Contractor’s Accounts And Records Relating To The Performance Of The Contractor And To Have Them Audited By Auditors Of The Gop Or The Procuring Entity, As May Be Required. 13. Advance Payment The Procuring Entity Shall, Upon A Written Request Of The Contractor Which Shall Be Submitted As A Contract Document, Make An Advance Payment To The Contractor In An Amount Not Exceeding Fifteen Percent (15%) Of The Total Contract Price, To Be Made In Lump Sum, Or At The Most Two Installments According To A Schedule Specified In The Scc, Subject To The Requirements In Annex “e” Of The 2016 Revised Irr Of Ra No. 9184. 14. Progress Payments The Contractor May Submit A Request For Payment For Work Accomplished. Such Requests For Payment Shall Be Verified And Certified By The Procuring Entity’s Representative/project Engineer. Except As Otherwise Stipulated In The Scc, Materials And Equipment Delivered On The Site But Not Completely Put In Place Shall Not Be Included For Payment. 15. Operating And Maintenance Manuals 15.1. If Required, The Contractor Will Provide “as Built” Drawings And/or Operating And Maintenance Manuals As Specified In The Scc. 15.2. If The Contractor Does Not Provide The Drawings And/or Manuals By The Dates Stated Above, Or They Do Not Receive The Procuring Entity’s Representative’s Approval, The Procuring Entity’s Representative May Withhold The Amount Stated In The Scc From Payments Due To The Contractor. Section V. Special Conditions Of Contract Gcc Clause 2 As Per Construction Schedule/contract Period 3.1 The Procuring Entity Shall Give Possession Of All Parts Of The Site To The Contractor Upon Effectivity Of The Contracts. 6 No Further Instructions 7.2 [in Case Of Permanent Structures, Such As Buildings Of Types 4 And 5 As Classified Under The National Building Code Of The Philippines And Other Structures Made Of Steel, Iron, Or Concrete Which Comply With Relevant Structural Codes (e.g., Dpwh Standard Specifications), Such As, But Not Limited To, Steel/concrete Bridges, Flyovers, Aircraft Movement Areas, Ports, Dams, Tunnels, Filtration And Treatment Plants, Sewerage Systems, Power Plants, Transmission And Communication Towers, Railway System, And Other Similar Permanent Structures:] Fifteen (15) Years. 10 Dayworks Are Applicable At The Rate Shown In The Contractor’s Original Bid. 11.1 No Further Instructions 11.2 No Further Instructions 13 The Amount Of The Advance Shall Not Exceed 15% Of The Total Contract Price. 14 Materials And Equipment Delivered On The Site But Not Completely Installed Or Constructed Shall Not Be Included For Payment. 15.1 The Date By Which Operating And Maintenance Manuals Are Required Shall Be At Least 5 Days Before The Testing And Commissioning. The Date By Which “as Built” Drawings Are Required Prior To The Final Billing. 15.2 The Amount To Be Withheld For Failing To Produce “as Built” Drawings And/or Operating And Maintenance Manuals By The Date Required Is 1% Of The Final Contract Amount. Section Vi. Specification General Requirements All Works To Be Done Shall Be With First Class Workmanship And Shall Conform To The Plans And Specifications. All Materials To Be Used Shall Be Of Good Quality And Properly Inspected By The Authorized Representative Or The Engineer In-charge. The Provincial Agriculturist Is Reserved The Right To Rescind, Terminate, Suspend The Contract If He Deems Necessary And To The Best Interest Of The Government. The Contractor Shall Be Liable For All Damages That Will Occur During The Construction Of The Project. Scope Of Works The Works Include Furnishing Of Labor, Materials, Tools, Equipment And Other Incidentals Necessary To Complete The Project Such As Mobilization/demobilization, Clearing, Grubbing & Staking, Excavation Works, Backfilling, Embankment With Compaction, Concrete Works, Masonry Works, Plastering Works, Wall Installation, Roof Framing, Roofing Works, Ceiling Works, Tile Works, Door And Windows With Complete Accessories, Plumbing Works, Painting Works, Construction Of Catch Basin, Installation Of Logo & Installation Of Electrical Works And Fire Alarm System. General Condition A. The Works To Be Done Herein Shall Be The Construction Of Warehouse As Of Approved And Of Quality Materials Completed As Per Plans, Details And Specifications. Supervision Of The Work Shall Be Done Under The Responsibility Of The Project Engineer With The Help Of The Construction Foreman. B. All Materials Employed And To Be Used In The Construction Shall Be Brand New, Unless Otherwise Or As Directed And Approved By The Project Engineer. C. Skilled Workmen And Workmanship Subject To Project Engineer’s Approval Shall Perform Methods Of The Construction In The Most Acceptable Manner. D. The Drawings Referred To In The Specifications Including Supplementary One, To Be Furnished As The Work Progress Are Intended To Cooperate With The Specification And To Form Part Hereof. Where Figures Are Given, They Are To Be Followed In Performance To Measurement By Scale. E. The Assigned Engineer Or Construction Foreman Shall Lay – Out The Building In Accordance With The Drawings And Directions On Plans As He Shall Not Only Responsible But Liable For Any Failure To Comply In This Respect With The Said Drawings, Specifications And Directions For Its Due And Accurate Location On The Lot. Project Sign Board / Billboard The Contractor Shall Ensure That The Project Site Is Identified With Information Billboard Which Shall Be Erected At The Beginning And Ending Of The Proposed Project. The Layout Of The Billboard Shall Accord To The Specifications Pursuant To The Commission On Audit (coa) Circular No. 2013-004 Issued On January 30, 2013. Coa Billboard Pao Billboard The Billboard’s Specifications Shall Conform To The Following Requirements: A. Tarpaulin, White, 8ft X 8ft (coa) And 4ft X 8ft (pao): B. Resolution: 70 Dpi; C. Font: Helvetica; D. Font Size: Main Information – 3”; E. Sub-information – 1”; F. Font Color: Black; G. Suitable Frame: Rigid Wood Or Steel Frame With Post; And, H. Posting: Outside Display At The Project Location After Award Has Been Made. Measurement The Supply And Erection Of Project Billboard Shall Be In Accordance With Provisions Of This Specification. Basis Of Payment No Additional Payment Shall Be Made In This Regard. A. Construction Of Warehouse I. Mobilization/demobilization Mobilization And Demobilization The Work Consists Of The Mobilization And Demobilization Of The Contractor’s Forces And Equipment Necessary For Performing The Work Required Under The Contract. It Does Not Include Mobilization And Demobilization For Specific Items Of Work In Fulfilling The Contract Requirements For The Commencement Of Work. Equipment And Material Mobilization Shall Include All Activities And Associated Costs For Transportation Of Contractor’s Personnel, Equipment, And Operating Supplies To The Site; Establishment Of Offices, Buildings, And Other Necessary General Facilities For The Contractor’s Operations At The Site. Demobilization Demobilization Shall Include All Activities And Associated Costs For Transportation Of Personnel, Equipment, And Supplies Not Required Or Included In The Contract From The Site; Including The Disassembly, Removal, And Site Cleanup Of Offices, Buildings, And Other Facilities Assembled On The Site Specifically For This Contract. Ii. Clearing, Grubbing And Staking Clearing And Grubbing And Cutting Of Trees Shall Include Handling, Salvaging, Piling And Disposing Off The Cleared Materials With All Leads And Lifts. Trees Shall Be Cut In Sections From The Top Downwards. All Timber Shall Not Be Used By The Contractor For Any Purpose And Shall Remain The Property Of The Provincial Agriculture Office. Clearing Shall Consist Of The Cutting, Removing And Disposal Of All Trees, Bushes, Shrubs, Grass, Weeds, Other Vegetation, Anthills, Rubbish, Fences, Top Organic Soil And Rocks And Boulders Exposed Or Lying On The Surface. The Construction Site Shall Be Leveled According To The Plans And Cleared Of Rubbish, Roots And Other Perishable And Objectionable Matters To A Suitable Subgrade. All Such Unsuitable Materials Shall Be Removed From The Construction Site And Spread Uniformly Over The Areas Adjacent To The Proposed Building, Or Otherwise Disposed Of As Maybe Directed By The Architect/engineer In-charge Of The Construction. Materials Obtained From Clearing And Grubbing Shall Be Disposed Off In Borrow Pits Or Other Suitable Places And Be Covered Up With Soil Or Gravel As Directed By The Engineer. The Burning Of Combustible Materials Shall Not Be Permitted. Staking-out The Building Lines Shall Be Staked Out On The Lines And Grades Shown In The Drawings Established Before Any Excavation Is Started. Batter Boards And Reference Marks Shall Be Erected At Such Place Where They Will Not Be Disturbed During The Excavation Of The Building. During The Period Of Commencement Of Works, The Contractor Shall Survey The Construction Area And Confirm The Levels. He Shall Immediately Notify The Engineer Of Any Discrepancies And Shall Agree With The Engineer Any Amended Values On The Plan. All Stations And Reference Points Shall Be Clearly Marked And Protected To The Satisfaction Of The Engineer. All Working Benchmarks Shall Be Near Major/medium Structure Sites. Accurate Establishment Of The Centerlines Based On The Drawing Is Required. The Existing Profile And Cross-section Shall Be Jointly Taken With The Engineer. Iii. Excavation Foundation Trench Shall Be Dug To The Exact Width And Depth And Levels As Indicated In The Drawings. Sides Of The Trenches Shall Be Vertical. In Case Soil Does Not Permit Vertical Sides, The Contractor Shall Protect The Sides With Timber Shoring. Excavated Earth Shall Not Be Placed Within 1.5 Meter Of The Edge Of The Trench. No Excavation Or Foundation Work Shall Be Filled In Or Covered Up Before The Inspection And Approval Of The Project Engineer. Iv. Backfilling, Embankment With Compaction And Gravel Bedding Use Earth Or Sand Free From Waste And Objectionable Materials. Place Backfill And Embank In Uniform Horizontal Layer Not More 150mm Thick At A Time, Puddle And Tamper Each Layer As Required To Make Firm Adequate Compaction. Fill Bottom Of Excavation For Structured Foundation With At Least 100mm Thick Gravel Before Placing Reinforcing Steel Bars And Pouring Concrete. V. Concrete, Masonry And Plastering Works A. General: All Concrete Works To Be Done Herein Shall Be In Accordance With Aci Requirement And/ Or Standard Specifications As Adopted By The Government. B. Cement Shall Be Portland Cement (type1) With 40 Kgs/bag. C. Fine Aggregates Shall Be Clean Hold River Sand, Free From Injurious Amount Of Clay, Loam And Vegetable Matter. D. Coarse Aggregates Shall Be River Run Gravel Or Broken Stones. The Maximum Size Shall Be 1/5 Of The Nearest Dimensions Between Side Forms Of The Concrete Members Or ¾ The Maximum Clear Spacing Between Reinforcing Bars. E. Reinforcing Bars: Reinforcing Bars Shall Be Intermediate Grade And Deformed And Shall Have Minimum Yield Strength Of 275 Mpa (40,000 Psi) F. The Wires Shall Be Locally Produced G.i. Wire Gauge No. 16. G. Placing Reinforcement Provide Bars, Wire Fabrics, Wire Ties, Supports And Other Devices Necessary To Install And Secure Reinforcement. Reinforcement Shall Not Contain Rust, Scale Oil, Grease Clay And Foreign Substances That Would Reduce The Bond. Rusting Of Reinforcement Is A Basis Of Rejection If The Effective Cross-sectional Area Of The Normal Weight Per Foot Of The Reinforcement Has Been Reduced To Less Than Specified In Paragraph Entitled “reinforcing Bars”. Remove Loose Rust Prior To Placing Of Steel. Splices Shall Be Approved Prior To Use. Do Not Splice At Points Of Maximum Stress. Overlapped Welded Wire Fabric The Spacing Of The Cross Wires, Plus 50 Mm (2 Inches). H. Concrete Hollow Blocks: 1. For Walls And Partitions, Use Chb Or Its Equivalent. 2. Minimum Comprehensive Strength Shall Be 700 Psi. I. All Concrete Cured For Least Seven (7) Days To Twenty-eight (28) Days If Possible After Placement To Attain The Required Strength Of Concrete. J. Removal Of Forms: Forms Shall Be Removed In Such A Manner As Not To Impair The Safety And Serviceability Of The Structures. K. Proportions Of All Materials Entering Into Concrete Shall Be Of Class “a”. L. Mixture For Concrete Slab: Thickness Of Slab Shall Be 200mm Thick. A Mixture Of Washed Sand, Screened Gravel And Portland Cement. M. Mixture For Plastering: Thickness Of Plaster Shall Be 16mm Thick. A Mixture Of Washed Sand And Portland Cement. Vi. Wall Installation Use 0.5mm Thk G.i. Rib-type Longspan Prepainted For Wall Cladding And 2” X 4” X 1.5mm X 6m C-purlins For Wall Cladding Framing. Vii. Roofing Works And Framing A. Roofing Must Be 0.5mm Pre-painted Rib-type Long Span With Compatible Ridge Roll, And Fascia With Skylight Roof. B. For Full Truss 1 & 2 And Half Truss 1, Trusses And Rafter Shall Be 2” X 2” X 5mm Thk Angle Bars For Top And Bottom Chord And 1-1/2” X 1-1/2” X 4.5mm Thk Angle Bar For All Web Members. C. For Half Truss 2, Use 2” Ø G.i. Pipe Schedule 40 For All Members. D. For Girt Use 2” X 2” X 5mm Thk Angle Bars For Top And Bottom Chord And 1-1/2” X 1-1/2” X 4.5mm Thk Angle Bar For All Web Members. E. For Fascia Frame Use 1” X 1” X 3/16” Thk Angle Bar For All Members. F. Use 2” X 6” X 1.5mm Thk C-purlins. Please Refer To The Attached Plan For Specifications. G. Fasten Framing Members Together By Welding Or By Using Bolts. Welding Shall Conform To Aws D1.3 Welding Procedure. H. All Metal Surfaces Must Be Metal Primer Red Oxide Painted. Ix. Ceiling Works All Materials Shall Be Of Kind And Size Specified On Plans. Interior And Exterior Ceiling Will Use 0.4mm Thk Spandrel Ceiling With A Carrying Channel, Metal Furring And Wall Angle For Corner As Main Frame. Use Blind Rivets To Fix The Spandrel To The Main Frame. X. Tile Works Tiles Should Be Installed In Comfort Room Using A 0.60m X 0.60m Polished Tiles. For Wall Tiles, Height Should Be 1.5m From The Finished Floor Line. Shall Have Tile Trim At The Edges And Provide Tile Grout Between Tiles. It Should Be Done By A Tile Setter To Ensure Quality Workmanship. Xi. Installation Of Doors A. For Sliding Door, Use G.a. 18 Plain Sheet For Door And 2” Ø G.i. Pipe Schedule 40 For The Frame With Heavy Duty Rack And Complete Accessories Including Installation. B. For Louver Windows, Use 0.5mm Plain Sheet Bended Louver Panels And 2” X 4” Rectangular Tube Framing With Complete Accessories Including Installation. C. For Comfort Room, Use 0.7m X 2.1m Pvc Door With Complete Accessories, Louver, Dr Pad And Lockset, And Use 6mm Thk X 0.4m X 0.6m Clear Glass Window On Analok Aluminum Tubular Frame With Complete Accessories. D. Use 0.9m X 2.1m Swing Panel Door, Kiln Dried Panel Door With 3mm Thk Lead Sheet With Heavy Duty Door Knob And Hinges On 2” X 6” Wooden Door Jamb. E. For Doors And Windows, Use #6, 4.5mm Steel Matting 2” X 2” X 4’ X 8’ And Use 3/16” X 1” X 6m Flat Bar And 2” Ø G.i. Pipe Schedule 40 For Framing. Xii. Plumbing Works All Works Shall Be Done In Accordance With The Provisions Of The Latest Edition Of The Plumbing Code And Local Ordinance. All Works Shall Be Done Under The Direct Supervision Of A Duly Licensed Master Plumber. See Attached Plans For Specifications. A. Use 1"ø Pvc Blue X 3m With Fittings And Accessories For Connection From Main Source Of Water To The Building For The Operation Of Comfort Room. B. Use 1/2"ø Pvc Blue X 3m With Fittings And Accessories For Faucets. C. Use 2"ø Pvc Sanitary X 3m S1000 With Fittings And Accessories For Floor Drain. D. Use 4"ø Pvc Sanitary X 3m S1000 With Fittings And Accessories For Septic Tank. Xiii. Painting Works I. Complete Painting Covers All Concrete Surfaces And Other Interior Parts Except Otherwise Specified. Ii. Apply Three (3) Coats As Paint Follows: 1st Coat = Sealer 2nd Coat = Primers 3rd Coat = Color Selected And Approved (2 Coats) Iii. Paint Shall Be Thoroughly Dry Before Applying The Succeeding Coat No Exterior Painting Shall Be Done With The Surface To Be Applied Is Damp Or During Rainy Weather Iv. Proper Works At All Times By Suitable Materials As Work Progress, Upon Completion Of Work, Remove All Paints Stains And Varnish Spots From Floors And Other Surfaces, Leave Work Clean And In Acceptable Condition. B. Construction Of Catch Basin And Septic Tank I. Excavation Foundation Trench Shall Be Dug To The Exact Width And Depth And Levels As Indicated In The Drawings. Sides Of The Trenches Shall Be Vertical. In Case Soil Does Not Permit Vertical Sides, The Contractor Shall Protect The Sides With Timber Shoring. Excavated Earth Shall Not Be Placed Within 1.5 Meter Of The Edge Of The Trench. No Excavation Or Foundation Work Shall Be Filled In Or Covered Up Before The Inspection And Approval Of The Project Engineer. Ii. Concrete, Masonry And Plastering Works A. General: All Concrete Works To Be Done Herein Shall Be In Accordance With Aci Requirement And/ Or Standard Specifications As Adopted By The Government. B. Cement Shall Be Portland Cement (type1) With 40 Kgs/bag. C. Fine Aggregates Shall Be Clean Hold River Sand, Free From Injurious Amount Of Clay, Loam And Vegetable Matter. D. Coarse Aggregates Shall Be River Run Gravel Or Broken Stones. The Maximum Size Shall Be 1/5 Of The Nearest Dimensions Between Side Forms Of The Concrete Members Or ¾ The Maximum Clear Spacing Between Reinforcing Bars. E. Reinforcing Bars: Reinforcing Bars Shall Be Intermediate Grade And Deformed And Shall Have Minimum Yield Strength Of 275 Mpa (40,000 Psi) F. The Wires Shall Be Locally Produced G.i. Wire Gauge No. 16. G. Placing Reinforcement Provide Bars, Wire Fabrics, Wire Ties, Supports And Other Devices Necessary To Install And Secure Reinforcement. Reinforcement Shall Not Contain Rust, Scale Oil, Grease Clay And Foreign Substances That Would Reduce The Bond. Rusting Of Reinforcement Is A Basis Of Rejection If The Effective Cross-sectional Area Of The Normal Weight Per Foot Of The Reinforcement Has Been Reduced To Less Than Specified In Paragraph Entitled “reinforcing Bars”. Remove Loose Rust Prior To Placing Of Steel. Splices Shall Be Approved Prior To Use. Do Not Splice At Points Of Maximum Stress. Overlapped Welded Wire Fabric The Spacing Of The Cross Wires, Plus 50 Mm (2 Inches). H. Concrete Hollow Blocks: 1. For Walls And Partitions, Use Chb Or Its Equivalent. 2. Minimum Comprehensive Strength Shall Be 700 Psi. I. All Concrete Cured For Least Seven (7) Days To Twenty-eight (28) Days If Possible After Placement To Attain The Required Strength Of Concrete. J. Removal Of Forms: Forms Shall Be Removed In Such A Manner As Not To Impair The Safety And Serviceability Of The Structures. K. Proportions Of All Materials Entering Into Concrete Shall Be Of Class “b”. L. Mixture For Concrete Slab: Thickness Of Slab Shall Be 100mm Thick. A Mixture Of Washed Sand, Screened Gravel And Portland Cement. M. Mixture For Plastering: Thickness Of Plaster Shall Be 16mm Thick. A Mixture Of Washed Sand And Portland Cement. Iii. Pipings Use 6” Ø Pvc Sanitary Pipe X 3m S1000 With Complete Fittings And Accessories. It Should Be Installed By A Skilled Plumber To Ensure Quality Workmanship. Please Refer To The Attached Plan For Specifications. C. Installation Of Logo Use 1.5m Ø X 4” Thk Stainless 202 Round Logo For The Iloilo Provincial Government Seal With Installation. It Should Be Installed By A Skilled Worker To Ensure Quality Workmanship. Please Refer To The Attached Plan For Specifications. D. Installation Of Electrical Works And Fire Alarm System Electrical Works The Electrical Installation Shall Be Done In Accordance With The Approved Plans And Under The Direct Supervision And Control Of A Professional Electrical Engineer And Or Registered Electrical Engineer. 1. All Electrical Works And Materials Shall Conform To The Provisions Of The Latest Edition Of The Philippine National Electrical Code. The Rules, Regulations And Requirements Of The Local Authorities That Have Jurisdiction Over The Project, And Of The Local Utility Companies For Electrical And Communication. 2. Power Service To The Building Shall Be 230 Vac, 3ø + Ground, & 60hz 3. Unless Otherwise Indicated, All Wiring Method Shall Be Done In Rigid Steel Conduit (rsc), Condulet Fittings & Metal Boxes. 4. All Electrical Materials/equipment To Be Used Shall Be New And Of The Approved Type In Accordance With Drawings And Specifications For Both Location And Purpose. 5. Unless Otherwise Specified In The Plans, The Minimum Size Of The Wire And Conduit To Be Used Shall Be 3.5mm2 Thhn And 20mmø, Respectively. All Wires Shall Be Insulated For 600v And Except As Specified In The Plan. 6. All Non-current Carrying Metal Parts Of Electrical Equipments, Panel Board & Other Devices Shall Be Effectively Bonded To The Ground. 7. The Entire Electrical Works Herein Shall Be Done Under Direct Supervision Of A Competent Registered Electrical Engineer. 8. Where So Required, Provide All Fittings, Condulets/boxes For All Systems. 9. Use Wire With Color Red For Line 1, Yellow For Line 2, Blue For Line 3, And Green For Line Ground. 10. Electrical Works/system Shall Be Commissioned With The Present Of Project Engineer. Fire Alarm System 1. Installation Of Fire Detection And Alarm System (fdas) Will Be In Accordance With The National Fire Protection Association (nfpa) 72 And 70 And Local Fire Code Of The Philippines. 2. All Wiring Will Be In Accordance With Fdas Manufacturer’s Recommendations To Properly Conduct The Circuit Current: -awg #16 Tf Wire Signaling Line Circuit -awg #16 Tf Wire 24vdc Auxiliary Circuit 3. Smoke Detectors And Heat Detectors Are To Be Installed According To The Recommended Spacing As Per Nfpa 72 And Manufacturer’s Listing: -smoke Detector 9.1m (area Coverage 0.7 Times Listed Spacing) -heat Detector 13.9m (area Coverage 0.7 Times Listed Spacing) 4. All Audible Devices Is At Least 15dba Above The Average Ambient Sound 5. Wiring Method Will Be In Electrical Metal Tubing (imc) And All Electrical Box Are Galvanized Ga #16 Minimum. 6. All Materials To Be Used Are New And Will Be Installed In Application For Which They Are Intended. Section Vii. Drawings Annex A – Architectural Design Annex B- Project Billboard Plan Section Viii. Bill Of Quantities Bid No. Agr- 24-1528-b Item Description Quantity Unit Unit Cost Total Cost No. A. Construction Of Warehouse I. Mobilization/demobilization 1.00 L.s. Pesos And Ctvs. (p ) / L.s. P Ii. Clearing, Grubbing & Staking 1080.00 Sq.m. Pesos And Ctvs. (p ) / Sq.m P Iii. Excavation Works 265.90 Cu.m. Pesos And Ctvs. (p ) / Cu.m P Iv. Backfilling 155.38 Cu.m. Pesos And Ctvs. (p ) / Cu.m P V. Embankment With Compaction 2067.00 Cu.m. Pesos And Ctvs. (p ) / Cu.m P Vi. Concrete Works A. Concreting 349.07 Cu.m. Pesos And Ctvs. (p ) / Cu.m P Item Description Quantity Unit Unit Cost Total Cost No. B. Gravel Bedding 151.01 Cu.m. Pesos And Ctvs. (p ) / Cu.m. P C. Steelworks 28,624.00 Kgs. Pesos And Ctvs. (p ) / Kgs. P D. Formworks 1,415.66 Sq.m. Pesos And Ctvs. (p ) / Sq.m P Vii. Masonry Works 186.12 Sq.m. Pesos And Ctvs. (p ) / Sq.m P Viii. Plastering Works 1,249.04 Sq.m. Pesos And Ctvs. (p ) /sq.m. P Ix. Wall Installation 764.47 Sq.m. Pesos And Ctvs. (p ) /sq.m. P X. Roof Framing 17,556.15 Kgs. Pesos And Ctvs. (p ) /kgs. P Xi. Roofing Works 619.50 Sq.m. Pesos And Ctvs. (p ) /sq.m. P Xii. Ceiling Works 22.33 Sq.m. Pesos And Ctvs. (p ) /sq.m. P Xiii. Tile Works 14.38 Sq.m. Pesos And Ctvs. (p ) /sq.m. P Xiv. Installation Of Doors And Windows A. Sliding Door (4.95m X 4.8m, 3.00 Units Pesos G.a. 18 Plain Sheet And 2” Ø G.i. Pipe S-40) W/ Heavy Duty Rack And Complete Accessories With Installation And Ctvs. (p ) /unit P B. Louver Windows (4.7m X Tube 18.00 Units Pesos 0.6mm, 2” X 4” Rectangular Framing And 0.5mm Plain Sheet Bended Louver Panels) W/ Complete Accessories With And Ctvs. Installation (p ) /unit P C. Panel/pvc/steel Matting Door 13.65 Sq.m. Pesos And Window And Clear Glass Window Installation And Ctvs. (p ) /sq.m. P Xv. Plumbing Works 1.00 L.s. Pesos And Ctvs. (p ) /l.s. P Xvi. Painting Works 3,727.18 Sq.m. Pesos And Ctvs. (p ) /sq.m. P B. Construction Of Catch Basin And Septic Tank I. Excavation Works 16.86 Cu.m. Pesos And Ctvs. (p ) /cu.m. P Ii. Concrete Works A. Concreting 3.30 Cu.m. Pesos And Ctvs. (p ) /cu.m. P B. Steel Works 178.00 Kgs. Pesos And Ctvs. (p ) /kgs. P C. Formworks 21.90 Sq.m. Pesos And Ctvs. (p ) /sq.m. P Iii. Masonry Works 40.60 Sq.m. Pesos And Ctvs. (p ) /sq.m. P Iv. Plastering Works 77.90 Sq.m. Pesos And Ctvs. (p ) /sq.m. P V. Pipings 1.00 L.s. Pesos And Ctvs. (p ) /l.s. P C. Installation Of Logo (1.5m Ø X 4” Thk Stainless 202 Round Logo With Installation) 1.00 L.s. Pesos And Ctvs. (p ) /l.s. P D. Installation Of Electrical Works & Fire Alarm System I. Installation Of Primary Lines, & 1.00 L.s. Pesos Metering & Three (3) Units Of 25 Kva Distribution Transformers (ileco Ii Works Recommended Materials) And Ctvs. (p ) /l.s. P Ii. Secondary Power Distribution 1.00 L.s. Pesos System And Ctvs. (p ) /l.s. P Iii. Fire Alarm System 1.00 L.s. Pesos And Ctvs. (p ) /l.s. P Total Bid Cost In Figures P Total Bid Cost In Words Summary Of Costs Item No. Bid Amount A. Construction Of Warehouse I. Mobilization/demobilization ₱ _____________________________ Ii. Clearing, Grubbing & Staking ₱ _____________________________ Iii. Excavation Works ₱ _____________________________ Iv. Backfilling ₱ _____________________________ V. Embankment With Compaction ₱ _____________________________ Vi. Concrete Works A. Concreting ₱ _____________________________ B. Gravel Bedding ₱ _____________________________ C. Steelworks ₱ _____________________________ D. Formworks ₱ _____________________________ Vii. Masonry Works ₱ _____________________________ Viii. Plastering Works ₱ _____________________________ Ix. Wall Installation ₱ _____________________________ X. Roof Framing ₱ _____________________________ Xi. Roofing Works ₱ _____________________________ Xii. Ceiling Works ₱ _____________________________ Xiii. Tile Works ₱ _____________________________ Xiv. Installation Of Doors And Windows A. Sliding Door (4.95m X 4.8m, G.a. 18 Plain Sheet And 2"ø G.i. Pipe S-40) W/ Heavy Duty Rack And Complete Accessories With Installation ₱ _____________________________ B. Louver Windows (4.7m X 0.6m, 2" X 4" Rectangular Tube Framing And 0.5mm Plain Sheet Bended Louver Panels) W/ Complete Accessories With Installation ₱ _____________________________ C. Panel/pvc/steel Matting Door And Window And Clear Glass Window Installation ₱ _____________________________ Xv. Plumbing Works ₱ _____________________________ Xvi. Painting Works ₱ _____________________________ B. Construction Of Catch Basin And Septic Tank I. Excavation Works ₱ _____________________________ Ii. Concrete Works A. Concreting ₱ _____________________________ B. Steelworks ₱ _____________________________ C. Formworks ₱ _____________________________ Iii. Masonry Works ₱ _____________________________ Iv. Plastering Works ₱ _____________________________ V. Pipings ₱ _____________________________ C. Installation Of Logo ₱ _____________________________ D. Installation Of Electrical Works & Fire Alarm System I. Installation Of Primary Lines, Metering & Three (3) Units Of 25 Kva Distribution Transformers (ileco Ii Works & Recommended Materials) ₱ _____________________________ Ii. Secondary Power Distribution System ₱ _____________________________ Iii. Fire Alarm System ₱ _____________________________ Total Bid Amount ₱ _____________________________ Section Ix. Checklist Of Technical And Financial Documents I. Technical Component Envelope Class “a” Documents Legal Documents ⬜ (a) Valid Philgeps Registration Certificate (platinum Membership) (all Pages) In Accordance With Section 8.5.2 Of The Irr; Technical Documents ⬜ (b) Statement Of The Prospective Bidder Of All Its Ongoing Government And Private Contracts, Including Contracts Awarded But Not Yet Started, If Any, Whether Similar Or Not Similar In Nature And Complexity To The Contract To Be Bid; And ⬜ (c) Statement Of The Bidder’s Single Largest Completed Contract (slcc) Similar To The Contract To Be Bid, Except Under Conditions Provided Under The Rules; And ⬜ (d) Special Pcab License In Case Of Joint Ventures; And Registration For The Type And Cost Of The Contract To Be Bid; And ⬜ (e) Original Copy Of Bid Security. If In The Form Of A Surety Bond, Submit Also A Certification Issued By The Insurance Commission; Or Original Copy Of Notarized Bid Securing Declaration; And (f) Project Requirements, Which Shall Include The Following: ⬜ A. Organizational Chart For The Contract To Be Bid; ⬜ B. List Of Contractor’s Key Personnel (e.g., Project Manager, Project Engineers, Materials Engineers, And Foremen), To Be Assigned To The Contract To Be Bid, With Their Complete Qualification And Experience Data; ⬜ C. List Of Contractor’s Major Equipment Units, Which Are Owned, Leased, And/or Under Purchase Agreements, Supported By Proof Of Ownership Or Certification Of Availability Of Equipment From The Equipment Lessor/vendor For The Duration Of The Project, As The Case May Be; And ⬜ (g) Original Duly Signed Omnibus Sworn Statement (oss); And If Applicable, Original Notarized Secretary’s Certificate In Case Of A Corporation, Partnership, Or Cooperative; Or Original Special Power Of Attorney Of All Members Of The Joint Venture Giving Full Power And Authority To Its Officer To Sign The Oss And Do Acts To Represent The Bidder. Financial Documents ⬜ (h) The Prospective Bidder’s Computation Of Net Financial Contracting Capacity (nfcc). Class “b” Documents ⬜ (i) If Applicable, Duly Signed Joint Venture Agreement (jva) In Accordance With Ra No. 4566 And Its Irr In Case The Joint Venture Is Already In Existence; Or Duly Notarized Statements From All The Potential Joint Venture Partners Stating That They Will Enter Into And Abide By The Provisions Of The Jva In The Instance That The Bid Is Successful. Ii. Financial Component Envelope ⬜ (j) Original Of Duly Signed And Accomplished Financial Bid Form; And Other Documentary Requirements Under Ra No. 9184 ⬜ (k) Original Of Duly Signed Bid Prices In The Bill Of Quantities; And ⬜ (l) Duly Accomplished Detailed Estimates Form, Including A Summary Sheet Indicating The Unit Prices Of Construction Materials, Labor Rates, And Equipment Rentals Used In Coming Up With The Bid; And ⬜ Cash Flow By Quarter. Bid Form For The Procurement Of Infrastructure Projects [shall Be Submitted With The Bid] Bid Form Date : Project Identification No. : To: [name And Address Of Procuring Entity] Having Examined The Philippine Bidding Documents (pbds) Including The Supplemental Or Bid Bulletin Numbers [insert Numbers], The Receipt Of Which Is Hereby Duly Acknowledged, We, The Undersigned, Declare That: A. We Have No Reservation To The Pbds, Including The Supplemental Or Bid Bulletins, For The Procurement Project: [insert Name Of Contract]; B. We Offer To Execute The Works For This Contract In Accordance With The Pbds; C. The Total Price Of Our Bid In Words And Figures, Excluding Any Discounts Offered Below Is: [insert Information]; D. The Discounts Offered And The Methodology For Their Application Are: [insert Information]; E. The Total Bid Price Includes The Cost Of All Taxes, Such As, But Not Limited To: [specify The Applicable Taxes, E.g. (i) Value Added Tax (vat), (ii) Income Tax, (iii) Local Taxes, And (iv) Other Fiscal Levies And Duties], Which Are Itemized Herein And Reflected In The Detailed Estimates, F. Our Bid Shall Be Valid Within A Period Stated In The Pbds, And It Shall Remain Binding Upon Us At Any Time Before The Expiration Of That Period; G. If Our Bid Is Accepted, We Commit To Obtain A Performance Security In The Amount Of [insert Percentage Amount] Percent Of The Contract Price For The Due Performance Of The Contract, Or A Performance Securing Declaration In Lieu Of The Allowable Forms Of Performance Security, Subject To The Terms And Conditions Of Issued Gppb Guidelines12 For This Purpose; H. We Are Not Participating, As Bidders, In More Than One Bid In This Bidding Process, Other Than Alternative Offers In Accordance With The Bidding Documents; I. We Understand That This Bid, Together With Your Written Acceptance Thereof Included In Your Notification Of Award, Shall Constitute A Binding Contract Between Us, Until A Formal Contract Is Prepared And Executed; And J. We Understand That You Are Not Bound To Accept The Lowest Calculated Bid Or Any Other Bid That You May Receive. K. We Likewise Certify/confirm That The Undersigned, Is The Duly Authorized Representative Of The Bidder, And Granted Full Power And Authority To Do, Execute 12 Currently Based On Gppb Resolution No. 09-2020 And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For The [name Of Project] Of The [name Of The Procuring Entity]. L. We Acknowledge That Failure To Sign Each And Every Page Of This Bid Form, Including The Bill Of Quantities, Shall Be A Ground For The Rejection Of Our Bid. Name: Legal Capacity: Signature: Duly Authorized To Sign The Bid For And Behalf Of: Date: Bid Securing Declaration Form [shall Be Submitted With The Bid If Bidder Opts To Provide This Form Of Bid Security] Republic Of The Philippines) City Of ) S.s. Bid Securing Declaration Project Identification No.: [insert Number] To: [insert Name And Address Of The Procuring Entity] I/we, The Undersigned, Declare That: 1. I/we Understand That, According To Your Conditions, Bids Must Be Supported By A Bid Security, Which May Be In The Form Of A Bid Securing Declaration. 2. I/we Accept That: (a) I/we Will Be Automatically Disqualified From Bidding For Any Procurement Contract With Any Procuring Entity For A Period Of Two (2) Years Upon Receipt Of Your Blacklisting Order; And, (b) I/we Will Pay The Applicable Fine Provided Under Section 6 Of The Guidelines On The Use Of Bid Securing Declaration, Within Fifteen (15) Days From Receipt Of The Written Demand By The Procuring Entity For The Commission Of Acts Resulting To The Enforcement Of The Bid Securing Declaration Under Sections 23.1(b), 34.2, 40.1 And 69.1, Except 69.1(f),of The Irr Of Ra No. 9184; Without Prejudice To Other Legal Action The Government May Undertake. 3. I/we Understand That This Bid Securing Declaration Shall Cease To Be Valid On The Following Circumstances: A. Upon Expiration Of The Bid Validity Period, Or Any Extension Thereof Pursuant To Your Request; B. I Am/we Are Declared Ineligible Or Post-disqualified Upon Receipt Of Your Notice To Such Effect, And (i) I/we Failed To Timely File A Request For Reconsideration Or (ii) I/we Filed A Waiver To Avail Of Said Right; And C. I Am/we Are Declared The Bidder With The Lowest Calculated Responsive Bid, And I/we Have Furnished The Performance Security And Signed The Contract. In Witness Whereof, I/we Have Hereunto Set My/our Hand/s This Day Of [month] [year] At [place Of Execution]. [insert Name Of Bidder Or Its Authorized Representative] [insert Signatory’s Legal Capacity] Affiant [jurat] [format Shall Be Based On The Latest Rules On Notarial Practice] Omnibus Sworn Statement (revised) [shall Be Submitted With The Bid] Republic Of The Philippines ) City/municipality Of ) S.s. Affidavit I, [name Of Affiant], Of Legal Age, [civil Status], [nationality], And Residing At [address Of Affiant], After Having Been Duly Sworn In Accordance With Law, Do Hereby Depose And State That: 1. [select One, Delete The Other:] [if A Sole Proprietorship:] I Am The Sole Proprietor Or Authorized Representative Of [name Of Bidder] With Office Address At [address Of Bidder]; [if A Partnership, Corporation, Cooperative, Or Joint Venture:] I Am The Duly Authorized And Designated Representative Of [name Of Bidder] With Office Address At [address Of Bidder]; 2. [select One, Delete The Other:] [if A Sole Proprietorship:] As The Owner And Sole Proprietor, Or Authorized Representative Of [name Of Bidder], I Have Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For [name Of The Project] Of The [name Of The Procuring Entity], As Shown In The Attached Duly Notarized Special Power Of Attorney; [if A Partnership, Corporation, Cooperative, Or Joint Venture:] I Am Granted Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For [name Of The Project] Of The [name Of The Procuring Entity], As Shown In The Attached [state Title Of Attached Document Showing Proof Of Authorization (e.g., Duly Notarized Secretary’s Certificate, Board/partnership Resolution, Or Special Power Of Attorney, Whichever Is Applicable;)]; 3. [name Of Bidder] Is Not “blacklisted” Or Barred From Bidding By The Government Of The Philippines Or Any Of Its Agencies, Offices, Corporations, Or Local Government Units, Foreign Government/foreign Or International Financing Institution Whose Blacklisting Rules Have Been Recognized By The Government Procurement Policy Board, By Itself Or By Relation, Membership, Association, Affiliation, Or Controlling Interest With Another Blacklisted Person Or Entity As Defined And Provided For In The Uniform Guidelines On Blacklisting; 4. Each Of The Documents Submitted In Satisfaction Of The Bidding Requirements Is An Authentic Copy Of The Original, Complete, And All Statements And Information Provided Therein Are True And Correct; 5. [name Of Bidder] Is Authorizing The Head Of The Procuring Entity Or Its Duly Authorized Representative(s) To Verify All The Documents Submitted; 6. [select One, Delete The Rest:] [if A Sole Proprietorship:] The Owner Or Sole Proprietor Is Not Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; [if A Partnership Or Cooperative:] None Of The Officers And Members Of [name Of Bidder] Is Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; [if A Corporation Or Joint Venture:] None Of The Officers, Directors, And Controlling Stockholders Of [name Of Bidder] Is Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; 7. [name Of Bidder] Complies With Existing Labor Laws And Standards; And 8. [name Of Bidder] Is Aware Of And Has Undertaken The Responsibilities As A Bidder In Compliance With The Philippine Bidding Documents, Which Includes: A. Carefully Examining All Of The Bidding Documents; B. Acknowledging All Conditions, Local Or Otherwise, Affecting The Implementation Of The Contract; C. Making An Estimate Of The Facilities Available And Needed For The Contract To Be Bid, If Any; And D. Inquiring Or Securing Supplemental/bid Bulletin(s) Issued For The [name Of The Project]. 9. [name Of Bidder] Did Not Give Or Pay Directly Or Indirectly, Any Commission, Amount, Fee, Or Any Form Of Consideration, Pecuniary Or Otherwise, To Any Person Or Official, Personnel Or Representative Of The Government In Relation To Any Procurement Project Or Activity. 10. In Case Advance Payment Was Made Or Given, Failure To Perform Or Deliver Any Of The Obligations And Undertakings In The Contract Shall Be Sufficient Grounds To Constitute Criminal Liability For Swindling (estafa) Or The Commission Of Fraud With Unfaithfulness Or Abuse Of Confidence Through Misappropriating Or Converting Any Payment Received By A Person Or Entity Under An Obligation Involving The Duty To Deliver Certain Goods Or Services, To The Prejudice Of The Public And The Government Of The Philippines Pursuant To Article 315 Of Act No. 3815 S. 1930, As Amended, Or The Revised Penal Code. In Witness Whereof, I Have Hereunto Set My Hand This Day Of , 20 At , Philippines. [insert Name Of Bidder Or Its Authorized Representative] [insert Signatory’s Legal Capacity] Affiant [jurat] [format Shall Be Based On The Latest Rules On Notarial Practice]

Details: Description Philippine Bidding Documents Repair Of Lrp Motorpool (rebid) Government Of The Republic Of The Philippines Sixth Edition March 2024 Table Of Contents Glossary Of 4 Terms, Abbreviations, And Acronyms 4 Section I. Invitation To Bid 7 Section Ii. Instructions To Bidders 10 1. Scope Of Bid 11 2. Funding Information 11 3. Bidding Requirements 11 4. Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices 11 5. Eligible Bidders 12 6. Origin Of Associated Goods 12 7. Subcontracts 12 8. Pre-bid Conference 12 9. Clarification And Amendment Of Bidding Documents 12 10. Documents Comprising The Bid: Eligibility And Technical Components 13 11. Documents Comprising The Bid: Financial Component 13 12. Alternative Bids 13 13. Bid Prices 14 14. Bid And Payment Currencies 14 15. Bid Security 14 16. Sealing And Marking Of Bids 14 17. Deadline For Submission Of Bids 14 18. Opening And Preliminary Examination Of Bids 15 19. Detailed Evaluation And Comparison Of Bids 15 20. Post Qualification 15 21. Signing Of The Contract 15 Section Iii. Bid Data Sheet 16 Section Iv. General Conditions Of Contract 19 1. Scope Of Contract 20 2. Sectional Completion Of Works 20 3. Possession Of Site 20 4. The Contractor’s Obligations 20 5. Performance Security 21 6. Site Investigation Reports 21 7. Warranty 21 8. Liability Of The Contractor 21 9. Termination For Other Causes 21 10. Dayworks 22 11. Program Of Work 22 12. Instructions, Inspections And Audits 22 13. Advance Payment 22 14. Progress Payments 22 15. Operating And Maintenance Manuals 22 Section V. Special Conditions Of Contract 24 Section Vi. Specifications 26 Section Vii. Drawings 29 Section Viii. Bill Of Quantities 38 Section Ix. Checklist Of Technical And Financial Documents 43 Omnibus Sworn Statement 51 Certificate Of Net Financial Contracting Capacity 54 Bid Form 55 Glossary Of Terms, Abbreviations, And Acronyms Abc – Approved Budget For The Contract. Arcc – Allowable Range Of Contract Cost. Bac – Bids And Awards Committee. Bid – A Signed Offer Or Proposal To Undertake A Contract Submitted By A Bidder In Response To And In Consonance With The Requirements Of The Bidding Documents. Also Referred To As Proposal And Tender. (2016 Revised Irr, Section 5[c]) Bidder – Refers To A Contractor, Manufacturer, Supplier, Distributor And/or Consultant Who Submits A Bid In Response To The Requirements Of The Bidding Documents. (2016 Revised Irr, Section 5[d]) Bidding Documents – The Documents Issued By The Procuring Entity As The Bases For Bids, Furnishing All Information Necessary For A Prospective Bidder To Prepare A Bid For The Goods, Infrastructure Projects, And/or Consulting Services Required By The Procuring Entity. (2016 Revised Irr, Section 5[e]) Bir – Bureau Of Internal Revenue. Bsp – Bangko Sentral Ng Pilipinas. Cda – Cooperative Development Authority. Consulting Services – Refer To Services For Infrastructure Projects And Other Types Of Projects Or Activities Of The Gop Requiring Adequate External Technical And Professional Expertise That Are Beyond The Capability And/or Capacity Of The Gop To Undertake Such As, But Not Limited To: (i) Advisory And Review Services; (ii) Pre-investment Or Feasibility Studies; (iii) Design; (iv) Construction Supervision; (v) Management And Related Services; And (vi) Other Technical Services Or Special Studies. (2016 Revised Irr, Section 5[i]) Contract – Refers To The Agreement Entered Into Between The Procuring Entity And The Supplier Or Manufacturer Or Distributor Or Service Provider For Procurement Of Goods And Services; Contractor For Procurement Of Infrastructure Projects; Or Consultant Or Consulting Firm For Procurement Of Consulting Services; As The Case May Be, As Recorded In The Contract Form Signed By The Parties, Including All Attachments And Appendices Thereto And All Documents Incorporated By Reference Therein. Contractor – Is A Natural Or Juridical Entity Whose Proposal Was Accepted By The Procuring Entity And To Whom The Contract To Execute The Work Was Awarded. Contractor As Used In These Bidding Documents May Likewise Refer To A Supplier, Distributor, Manufacturer, Or Consultant. Cpi – Consumer Price Index. Dole – Department Of Labor And Employment. Dti – Department Of Trade And Industry. Foreign-funded Procurement Or Foreign-assisted Project – Refers To Procurement Whose Funding Source Is From A Foreign Government, Foreign Or International Financing Institution As Specified In The Treaty Or International Or Executive Agreement. (2016 Revised Irr, Section 5[b]). Gfi – Government Financial Institution. Gocc – Government-owned And/or –controlled Corporation. Goods – Refer To All Items, Supplies, Materials And General Support Services, Except Consulting Services And Infrastructure Projects, Which May Be Needed In The Transaction Of Public Businesses Or In The Pursuit Of Any Government Undertaking, Project Or Activity, Whether In The Nature Of Equipment, Furniture, Stationery, Materials For Construction, Or Personal Property Of Any Kind, Including Non-personal Or Contractual Services Such As The Repair And Maintenance Of Equipment And Furniture, As Well As Trucking, Hauling, Janitorial, Security, And Related Or Analogous Services, As Well As Procurement Of Materials And Supplies Provided By The Procuring Entity For Such Services. The Term “related” Or “analogous Services” Shall Include, But Is Not Limited To, Lease Or Purchase Of Office Space, Media Advertisements, Health Maintenance Services, And Other Services Essential To The Operation Of The Procuring Entity. (2016 Revised Irr, Section 5[r]) Gop – Government Of The Philippines. Infrastructure Projects – Include The Construction, Improvement, Rehabilitation, Demolition, Repair, Restoration Or Maintenance Of Roads And Bridges, Railways, Airports, Seaports, Communication Facilities, Civil Works Components Of Information Technology Projects, Irrigation, Flood Control And Drainage, Water Supply, Sanitation, Sewerage And Solid Waste Management Systems, Shore Protection, Energy/power And Electrification Facilities, National Buildings, School Buildings, Hospital Buildings, And Other Related Construction Projects Of The Government. Also Referred To As Civil Works Or Works. (2016 Revised Irr, Section 5[u]) Lgus – Local Government Units. Nfcc – Net Financial Contracting Capacity. Nga – National Government Agency. Pcab – Philippine Contractors Accreditation Board. Philgeps - Philippine Government Electronic Procurement System. Procurement Project – Refers To A Specific Or Identified Procurement Covering Goods, Infrastructure Project Or Consulting Services. A Procurement Project Shall Be Described, Detailed, And Scheduled In The Project Procurement Management Plan Prepared By The Agency Which Shall Be Consolidated In The Procuring Entity's Annual Procurement Plan. (gppb Circular No. 06-2019 Dated 17 July 2019) Psa – Philippine Statistics Authority. Sec – Securities And Exchange Commission. Slcc – Single Largest Completed Contract. Un – United Nations. Section I. Invitation To Bid Republic Of The Philippines Department Of Justice Bureau Of Corrections Leyte Regional Prison Abuyog, Leyte Invitation To Bid For Repair Of Lrp Motorpool (rebid) 1. The Leyte Regional Prison, Through The 2023 Continuing Funds Intends To Apply The Sum Of Two Million One Hundred Twenty-three Thousand Five Hundred Twenty-two Pesos & 10/100 (₱2,123,522.10) Being The Approved Budget Of The Contract (abc) To Payments Under The Contract For Repair Of Lrp Motorpool (rebid) With Identification Number Bid2024-001. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. 2. The Leyte Regional Prison, Now Invites Bids For The Above Procurement Project. Completion Of The Works Is Required Two Hundred Ten (210) Calendar Days From The Receipt Of Notice To Proceed (ntp) And Contract Agreement. Bidders Should Have Completed A Contract Similar To The Project Amounting To At Least Fifty Percent (50%) Of The Abc Within The Last Four (4) Years. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii (instructions To Bidders). 3. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) No. 9184. 4. Interested Bidders May Obtain Further Information From Leyte Regional Prison And Inspect The Bidding Documents At The Address Given Below From Monday To Friday From 8:00am To 5:00pm. 5. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders On March 14, 2024 8:00am - 5:00pm To April 3, 2024 8:00am – 8:55am From The Given Address And Website(s) Below. It May Also Be Downloaded Free Of Charge From The Website Of The Philippine Government Electronic Procurement System (philgeps) And The Website Of The Procuring Entity Bucor.gov.ph, Provided That Bidders Shall Pay The Applicable Fee Of Five Thousand Pesos Only (₱5,000.00) For The Bidding Documents Not Later Than The Submission Of Their Bids. The Procuring Entity Shall Allow The Bidder To Present Its Proof Of Payment For The Fees In Person. 6. The Leyte Regional Prison Will Hold A Pre-bid Conference On March 22, 2024 -9:00am At Lrp – Conference Room, Administration Building, Leyte Regional Prison, Which Shall Be Open To Prospective Bidders. 7. Bids Must Be Duly Received By The Bac Secretariat Through Manual Submission At The Office Address Indicated Below On Or Before April 3, 2024 – 8:55am. Late Bids Shall Not Be Accepted. 8. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 15. 9. Bid Opening Shall Be On April 3, 2024 – 9:00am At The Lrp – Conference Room, Administration Building, Leyte Regional Prison. Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend The Activity. 10. The Leyte Regional Prison Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Irr Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 11. For Further Information, Please Refer To: Jeruel Go Office Of The Bac Secretariat Leyte Regional Prison Abuyog, Leyte Cp # 09455311532 Email: Lrpbac@bucor.gov.ph 12. You May Visit The Following Websites: For Downloading Of Bidding Documents Bucor.gov.ph Date Of Issue: March 14, 2024 Section Ii. Instructions To Bidders 1. Scope Of Bid The Leyte Regional Prison Invite Bids For The Repair Of Lrp Motorpool (rebid), With Identification Number Bid2024-001. The Repair Of Lrp Motorpool (rebid) (referred To Herein As “project”) Is Composed Of Works, As Described In Section Vi (specifications). 2. Funding Information 2.1. The Gop Through The Source Of Funding As Indicated Below For Cy 2024 In The Amount Of Two Million One Hundred Twenty-three Thousand Five Hundred Twenty-two Pesos & 10/100 (₱2,123,522.10). 2.2. The Source Of Funding Is Nga, The General Appropriations Act Or Special Appropriations. 3. Bidding Requirements The Bidding For The Project Shall Be Governed By All The Provisions Of Ra No. 9184 And Its 2016 Revised Irr, Including Its Generic Procurement Manual And Associated Policies, Rules And Regulations As The Primary Source Thereof, While The Herein Clauses Shall Serve As The Secondary Source Thereof. Any Amendments Made To The Irr And Other Gppb Issuances Shall Be Applicable Only To The Ongoing Posting, Advertisement, Or Invitation To Bid By The Bac Through The Issuance Of A Supplemental Or Bid Bulletin. The Bidder, By The Act Of Submitting Its Bid, Shall Be Deemed To Have Inspected The Site, Determined The General Characteristics Of The Contracted Works And The Conditions For This Project, Such As The Location And The Nature Of The Work; (b) Climatic Conditions; (c) Transportation Facilities; (c) Nature And Condition Of The Terrain, Geological Conditions At The Site Communication Facilities, Requirements, Location And Availability Of Construction Aggregates And Other Materials, Labor, Water, Electric Power And Access Roads; And (d) Other Factors That May Affect The Cost, Duration And Execution Or Implementation Of The Contract, Project, Or Work And Examine All Instructions, Forms, Terms, And Project Requirements In The Bidding Documents. 4. Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices The Procuring Entity, As Well As The Bidders And Contractors, Shall Observe The Highest Standard Of Ethics During The Procurement And Execution Of The Contract. They Or Through An Agent Shall Not Engage In Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices Defined Under Annex “i” Of The 2016 Revised Irr Of Ra No. 9184 Or Other Integrity Violations In Competing For The Project. 5. Eligible Bidders 5.1. Only Bids Of Bidders Found To Be Legally, Technically, And Financially Capable Will Be Evaluated. 5.2. The Bidder Must Have An Experience Of Having Completed A Single Largest Completed Contract (slcc) That Is Similar To This Project, Equivalent To At Least Fifty Percent (50%) Of The Abc Adjusted, If Necessary, By The Bidder To Current Prices Using The Psa’s Cpi, Except Under Conditions Provided For In Section 23.4.2.4 Of The 2016 Revised Irr Of Ra No. 9184. A Contract Is Considered To Be “similar” To The Contract To Be Bid If It Has The Major Categories Of Work Stated In The Bds. 5.3. For Foreign-funded Procurement, The Procuring Entity And The Foreign Government/foreign Or International Financing Institution May Agree On Another Track Record Requirement, As Specified In The Bidding Document Prepared For This Purpose. 5.4. The Bidders Shall Comply With The Eligibility Criteria Under Section 23.4.2 Of The 2016 Irr Of Ra No. 9184. 6. Origin Of Associated Goods There Is No Restriction On The Origin Of Goods Other Than Those Prohibited By A Decision Of The Un Security Council Taken Under Chapter Vii Of The Charter Of The Un. 7. Subcontracts 7.1. The Bidder May Subcontract Portions Of The Project To The Extent Allowed By The Procuring Entity As Stated Herein, But In No Case More Than Fifty Percent (50%) Of The Project. The Procuring Entity Has Prescribed That Subcontracting Is Not Allowed. 8. Pre-bid Conference The Procuring Entity Will Hold A Pre-bid Conference For This Project On The Specified Date And Time And Either At Its Physical Address As Indicated In Paragraph 6 Of The Ib. 9. Clarification And Amendment Of Bidding Documents Prospective Bidders May Request For Clarification On And/or Interpretation Of Any Part Of The Bidding Documents. Such Requests Must Be In Writing And Received By The Procuring Entity, Either At Its Given Address Or Through Electronic Mail Indicated In The Ib, At Least Ten (10) Calendar Days Before The Deadline Set For The Submission And Receipt Of Bids. 10. Documents Comprising The Bid: Eligibility And Technical Components 10.1. The First Envelope Shall Contain The Eligibility And Technical Documents Of The Bid As Specified In Section Ix. Checklist Of Technical And Financial Documents. 10.2. If The Eligibility Requirements Or Statements, The Bids, And All Other Documents For Submission To The Bac Are In Foreign Language Other Than English, It Must Be Accompanied By A Translation In English, Which Shall Be Authenticated By The Appropriate Philippine Foreign Service Establishment, Post, Or The Equivalent Office Having Jurisdiction Over The Foreign Bidder’s Affairs In The Philippines. For Contracting Parties To The Apostille Convention, Only The Translated Documents Shall Be Authenticated Through An Apostille Pursuant To Gppb Resolution No. 13-2019 Dated 23 May 2019. The English Translation Shall Govern, For Purposes Of Interpretation Of The Bid. 10.3. A Valid Pcab License Is Required, And In Case Of Joint Ventures, A Valid Special Pcab License, And Registration For The Type And Cost Of The Contract For This Project. Any Additional Type Of Contractor License Or Permit Shall Be Indicated In The Bds. 10.4. A List Of Contractor’s Key Personnel (e.g., Project Manager, Project Engineers, Materials Engineers, And Foremen) Assigned To The Contract To Be Bid, With Their Complete Qualification And Experience Data Shall Be Provided. These Key Personnel Must Meet The Required Minimum Years Of Experience Set In The Bds. 10.5. A List Of Contractor’s Major Equipment Units, Which Are Owned, Leased, And/or Under Purchase Agreements, Supported By Proof Of Ownership, Certification Of Availability Of Equipment From The Equipment Lessor/vendor For The Duration Of The Project, As The Case May Be, Must Meet The Minimum Requirements For The Contract Set In The Bds. 11. Documents Comprising The Bid: Financial Component 11.1. The Second Bid Envelope Shall Contain The Financial Documents For The Bid As Specified In Section Ix. Checklist Of Technical And Financial Documents. 11.2. Any Bid Exceeding The Abc Indicated In Paragraph 1 Of The Ib Shall Not Be Accepted. 11.3. For Foreign-funded Procurement, A Ceiling May Be Applied To Bid Prices Provided The Conditions Are Met Under Section 31.2 Of The 2016 Revised Irr Of Ra No. 9184. 12. Alternative Bids Bidders Shall Submit Offers That Comply With The Requirements Of The Bidding Documents, Including The Basic Technical Design As Indicated In The Drawings And Specifications. Unless There Is A Value Engineering Clause In The Bds, Alternative Bids Shall Not Be Accepted. 13. Bid Prices All Bid Prices For The Given Scope Of Work In The Project As Awarded Shall Be Considered As Fixed Prices, And Therefore Not Subject To Price Escalation During Contract Implementation, Except Under Extraordinary Circumstances As Determined By The Neda And Approved By The Gppb Pursuant To The Revised Guidelines For Contract Price Escalation Guidelines. 14. Bid And Payment Currencies 14.1. Bid Prices May Be Quoted In The Local Currency Or Tradeable Currency Accepted By The Bsp At The Discretion Of The Bidder. However, For Purposes Of Bid Evaluation, Bids Denominated In Foreign Currencies Shall Be Converted To Philippine Currency Based On The Exchange Rate As Published In The Bsp Reference Rate Bulletin On The Day Of The Bid Opening. 14.2. Payment Of The Contract Price Shall Be Made In Philippine Pesos. 15. Bid Security 15.1. The Bidder Shall Submit A Bid Securing Declaration Or Any Form Of Bid Security In The Amount Indicated In The Bds, Which Shall Be Not Less Than The Percentage Of The Abc In Accordance With The Schedule In The Bds. 15.2. The Bid And Bid Security Shall Be Valid Until August 1, 2024. Any Bid Not Accompanied By An Acceptable Bid Security Shall Be Rejected By The Procuring Entity As Non-responsive. 16. Sealing And Marking Of Bids Each Bidder Shall Submit One Copy Of The First And Second Components Of Its Bid. The Procuring Entity May Request Additional Hard Copies And/or Electronic Copies Of The Bid. However, Failure Of The Bidders To Comply With The Said Request Shall Not Be A Ground For Disqualification. If The Procuring Entity Allows The Submission Of Bids Through Online Submission To The Given Website Or Any Other Electronic Means, The Bidder Shall Submit An Electronic Copy Of Its Bid, Which Must Be Digitally Signed. An Electronic Copy That Cannot Be Opened Or Is Corrupted Shall Be Considered Non-responsive And, Thus, Automatically Disqualified. 17. Deadline For Submission Of Bids The Bidders Shall Submit On The Specified Date And Time And Either At Its Physical Address Or Through Online Submission As Indicated In Paragraph 7 Of The Ib. 18. Opening And Preliminary Examination Of Bids 18.1. The Bac Shall Open The Bids In Public At The Time, On The Date, And At The Place Specified In Paragraph 9 Of The Ib. The Bidders’ Representatives Who Are Present Shall Sign A Register Evidencing Their Attendance. In Case Videoconferencing, Webcasting Or Other Similar Technologies Will Be Used, Attendance Of Participants Shall Likewise Be Recorded By The Bac Secretariat. In Case The Bids Cannot Be Opened As Scheduled Due To Justifiable Reasons, The Rescheduling Requirements Under Section 29 Of The 2016 Revised Irr Of Ra No. 9184 Shall Prevail. 18.2. The Preliminary Examination Of Bids Shall Be Governed By Section 30 Of The 2016 Revised Irr Of Ra No. 9184. 19. Detailed Evaluation And Comparison Of Bids 19.1. The Procuring Entity’s Bac Shall Immediately Conduct A Detailed Evaluation Of All Bids Rated “passed” Using Non-discretionary Pass/fail Criteria. The Bac Shall Consider The Conditions In The Evaluation Of Bids Under Section 32.2 Of 2016 Revised Irr Of Ra No. 9184. 19.2. If The Project Allows Partial Bids, All Bids And Combinations Of Bids As Indicated In The Bds Shall Be Received By The Same Deadline And Opened And Evaluated Simultaneously So As To Determine The Bid Or Combination Of Bids Offering The Lowest Calculated Cost To The Procuring Entity. Bid Security As Required By Itb Clause 16 Shall Be Submitted For Each Contract (lot) Separately. 19.3. In All Cases, The Nfcc Computation Pursuant To Section 23.4.2.6 Of The 2016 Revised Irr Of Ra No. 9184 Must Be Sufficient For The Total Of The Abcs For All The Lots Participated In By The Prospective Bidder. 20. Post Qualification Within A Non-extendible Period Of Five (5) Calendar Days From Receipt By The Bidder Of The Notice From The Bac That It Submitted The Lowest Calculated Bid, The Bidder Shall Submit Its Latest Income And Business Tax Returns Filed And Paid Through The Bir Electronic Filing And Payment System (efps), And Other Appropriate Licenses And Permits Required By Law And Stated In The Bds. 21. Signing Of The Contract The Documents Required In Section 37.2 Of The 2016 Revised Irr Of Ra No. 9184 Shall Form Part Of The Contract. Additional Contract Documents Are Indicated In The Bds. Section Iii. Bid Data Sheet Itb Clause Bid Data Sheet 5.2 For This Purpose, Contracts Similar To The Project Refer To Contracts Which Have The Same Major Categories Of Work, Which Shall Be: Electrical (residential, Commercial, Industrial, Maintenance, Installation, Construction) Works And Repair, Rehabilitation And Infrastructure/construction Works 7.1 Subcontracting Is Not Allowed 10.3 A Valid Pcab License Is Required, And In Case Of Joint Ventures, A Valid Special Pcab License, And Registration For The Type And Cost Of The Contract For This Project. 10.4 The Key Personnel Must Meet The Required Minimum Years Of Experience Set Below: Key Personnel General Experience Relevant Experience Project Manager Duly Licensed Civil Engineer/architect With At Least 5 Years’ Experience Similar Or Comparable Projects, With Knowledge In The Application Of Rapid Construction Foreman With At Least 5 Years’ Experience As Foreman Similar Or Comparable Projects, With Knowledge In The Application Of Rapid Construction 10.5 The Minimum Major Equipment Requirements Are The Following: Equipment Capacity Number Of Units Service Vehicle For Hauling Of Materials One (1) Cement Mixer 1 Bagger One (1) 12.0 No Further Instructions 15.1 The Bid Security Shall Be In The Form Of A Bid Securing Declaration, Or Any Of The Following Forms And Amounts: The Amount Of Not Less Than P42,470.44 Or Two Percent (2%) Of Abc, If Bid Security Is In Cash, Cashier’s/manager’s Check, Bank Draft/guarantee Or Irrevocable Letter Of Credit; Or The Amount Of Not Less Than 106,176.10 Or Five Percent (5%) Of Abc] If Bid Security Is In Surety Bond. 19.2 Partial Bids Are Not Allowed 20 Within A Non-extendible Period Of Five (5) Calendar Days From Receipt By The Bidder Of The Notice From The Bac That It Submitted The Lowest Calculated Bid, The Bidder Shall Submit The Following Documentary Requirements: • Conformity With The Technical Specifications (scope Of Work); And • Conformity With The Plans/drawings. • Each And Every Page Of The Bid Data Sheets And Special Conditions Of The Contract Shall Be Initialed By The Authorized Representative Of The Bidder. • The Prospective Bidder’s Audited Financial Statements, Showing, Among Others, The Prospective Bidder’s Total And Current Assets And Liabilities, Stamped “received” By The Bir Or Its Duly Accredited And Authorized Institutions, For The Preceding Calendar Year Which Should Not Be Earlier Than Two (2) Years From The Date Of Bid Submission. 21 Additional Contract Documents Relevant To The Project That May Be Required By Existing Laws And/or The Procuring Entity, Such As Construction Schedule And S-curve, Manpower Schedule, Construction Methods, Equipment Utilization Schedule, Construction Safety And Health Program Approved By The Dole, And Other Acceptable Tools Of Project Scheduling. Section Iv. General Conditions Of Contract 1. Scope Of Contract This Contract Shall Include All Such Items, Although Not Specifically Mentioned, That Can Be Reasonably Inferred As Being Required For Its Completion As If Such Items Were Expressly Mentioned Herein. All The Provisions Of Ra No. 9184 And Its 2016 Revised Irr, Including The Generic Procurement Manual, And Associated Issuances, Constitute The Primary Source For The Terms And Conditions Of The Contract, And Thus, Applicable In Contract Implementation. Herein Clauses Shall Serve As The Secondary Source For The Terms And Conditions Of The Contract. This Is Without Prejudice To Sections 74.1 And 74.2 Of The 2016 Revised Irr Of Ra No. 9184 Allowing The Gppb To Amend The Irr, Which Shall Be Applied To All Procurement Activities, The Advertisement, Posting, Or Invitation Of Which Were Issued After The Effectivity Of The Said Amendment. 2. Sectional Completion Of Works If Sectional Completion Is Specified In The Special Conditions Of Contract (scc), References In The Conditions Of Contract To The Works, The Completion Date, And The Intended Completion Date Shall Apply To Any Section Of The Works (other Than References To The Completion Date And Intended Completion Date For The Whole Of The Works). 3. Possession Of Site 3.1 The Procuring Entity Shall Give Possession Of All Or Parts Of The Site To The Contractor Based On The Schedule Of Delivery Indicated In The Scc, Which Corresponds To The Execution Of The Works. If The Contractor Suffers Delay Or Incurs Cost From Failure On The Part Of The Procuring Entity To Give Possession In Accordance With The Terms Of This Clause, The Procuring Entity’s Representative Shall Give The Contractor A Contract Time Extension And Certify Such Sum As Fair To Cover The Cost Incurred, Which Sum Shall Be Paid By Procuring Entity. 3.2 If Possession Of A Portion Is Not Given By The Above Date, The Procuring Entity Will Be Deemed To Have Delayed The Start Of The Relevant Activities. The Resulting Adjustments In Contract Time To Address Such Delay May Be Addressed Through Contract Extension Provided Under Annex “e” Of The 2016 Revised Irr Of Ra No. 9184. 4. The Contractor’s Obligations The Contractor Shall Employ The Key Personnel Named In The Schedule Of Key Personnel Indicating Their Designation, In Accordance With Itb Clause 10.3 And Specified In The Bds, To Carry Out The Supervision Of The Works. The Procuring Entity Will Approve Any Proposed Replacement Of Key Personnel Only If Their Relevant Qualifications And Abilities Are Equal To Or Better Than Those Of The Personnel Listed In The Schedule. 5. Performance Security 5.1. Within Ten (10) Calendar Days From Receipt Of The Notice Of Award From The Procuring Entity But In No Case Later Than The Signing Of The Contract By Both Parties, The Successful Bidder Shall Furnish The Performance Security In Any Of The Forms Prescribed In Section 39 Of The 2016 Revised Irr. 5.2. The Contractor, By Entering Into The Contract With The Procuring Entity, Acknowledges The Right Of The Procuring Entity To Institute Action Pursuant To Ra No. 3688 Against Any Subcontractor Be They An Individual, Firm, Partnership, Corporation, Or Association Supplying The Contractor With Labor, Materials And/or Equipment For The Performance Of This Contract. 6. Site Investigation Reports The Contractor, In Preparing The Bid, Shall Rely On Any Site Investigation Reports Referred To In The Scc Supplemented By Any Information Obtained By The Contractor. 7. Warranty 7.1. In Case The Contractor Fails To Undertake The Repair Works Under Section 62.2.2 Of The 2016 Revised Irr, The Procuring Entity Shall Forfeit Its Performance Security, Subject Its Property(ies) To Attachment Or Garnishment Proceedings, And Perpetually Disqualify It From Participating In Any Public Bidding. All Payables Of The Gop In His Favor Shall Be Offset To Recover The Costs. 7.2. The Warranty Against Structural Defects/failures, Except That Occasioned-on Force Majeure, Shall Cover The Period From The Date Of Issuance Of The Certificate Of Final Acceptance By The Procuring Entity. Specific Duration Of The Warranty Is Found In The Scc. 8. Liability Of The Contractor Subject To Additional Provisions, If Any, Set Forth In The Scc, The Contractor’s Liability Under This Contract Shall Be As Provided By The Laws Of The Republic Of The Philippines. If The Contractor Is A Joint Venture, All Partners To The Joint Venture Shall Be Jointly And Severally Liable To The Procuring Entity. 9. Termination For Other Causes Contract Termination Shall Be Initiated In Case It Is Determined Prima Facie By The Procuring Entity That The Contractor Has Engaged, Before, Or During The Implementation Of The Contract, In Unlawful Deeds And Behaviors Relative To Contract Acquisition And Implementation, Such As, But Not Limited To Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices As Stated In Itb Clause 4. 10. Dayworks Subject To The Guidelines On Variation Order In Annex “e” Of The 2016 Revised Irr Of Ra No. 9184, And If Applicable As Indicated In The Scc, The Dayworks Rates In The Contractor’s Bid Shall Be Used For Small Additional Amounts Of Work Only When The Procuring Entity’s Representative Has Given Written Instructions In Advance For Additional Work To Be Paid For In That Way. 11. Program Of Work 11.1. The Contractor Shall Submit To The Procuring Entity’s Representative For Approval The Said Program Of Work Showing The General Methods, Arrangements, Order, And Timing For All The Activities In The Works. The Submissions Of The Program Of Work Are Indicated In The Scc. 11.2. The Contractor Shall Submit To The Procuring Entity’s Representative For Approval An Updated Program Of Work At Intervals No Longer Than The Period Stated In The Scc. If The Contractor Does Not Submit An Updated Program Of Work Within This Period, The Procuring Entity’s Representative May Withhold The Amount Stated In The Scc From The Next Payment Certificate And Continue To Withhold This Amount Until The Next Payment After The Date On Which The Overdue Program Of Work Has Been Submitted. 12. Instructions, Inspections And Audits The Contractor Shall Permit The Gop Or The Procuring Entity To Inspect The Contractor’s Accounts And Records Relating To The Performance Of The Contractor And To Have Them Audited By Auditors Of The Gop Or The Procuring Entity, As May Be Required. 13. Advance Payment The Procuring Entity Shall, Upon A Written Request Of The Contractor Which Shall Be Submitted As A Contract Document, Make An Advance Payment To The Contractor In An Amount Not Exceeding Fifteen Percent (15%) Of The Total Contract Price, To Be Made In Lump Sum, Or At The Most Two Installments According To A Schedule Specified In The Scc, Subject To The Requirements In Annex “e” Of The 2016 Revised Irr Of Ra No. 9184. 14. Progress Payments The Contractor May Submit A Request For Payment For Work Accomplished. Such Requests For Payment Shall Be Verified And Certified By The Procuring Entity’s Representative/project Engineer. Except As Otherwise Stipulated In The Scc, Materials And Equipment Delivered On The Site But Not Completely Put In Place Shall Not Be Included For Payment. 15. Operating And Maintenance Manuals 15.1. If Required, The Contractor Will Provide “as Built” Drawings And/or Operating And Maintenance Manuals As Specified In The Scc. 15.2. If The Contractor Does Not Provide The Drawings And/or Manuals By The Dates Stated Above, Or They Do Not Receive The Procuring Entity’s Representative’s Approval, The Procuring Entity’s Representative May Withhold The Amount Stated In The Scc From Payments Due To The Contractor. Section V. Special Conditions Of Contract Special Conditions Of Contract Gcc Clause 2 Sectional Completion Is Not Applicable The Intended Completion Date Is Two Hundred Ten (210) Calendar Days From The Date Of Receipt Of The Ntp. 4.1 The Procuring Entity Shall Give Possession Of All Parts Of The Site To The Contractor From The Date Of The Receipt Of Notice To Proceed (ntp). 6 No Further Instructions 7.2 A Five (5) Year Warranty Against Structural Defects/failures, Except That Occasioned-on Force Majeure, Shall Cover The Period From The Date Of Issuance Of The Certificate Of Final Acceptance By The Procuring Entity. 10 No Day Works Are Applicable To The Contract. 11.1 The Contractor Shall Submit The Program Of Work To The Procuring Entity’s Representative Within Fourteen (14) Days Of Delivery Of The Notice Of Award. 11.2 The Amount To Be Withheld For Late Submission Of An Updated Program Of Work Is Fifty Thousand Pesos (p50,000.00). 13 The Amount Of The Advance Payment Is Fifteen Percent (15%) Of The Contract Price To Be Made In Lump Sum Upon Submission To And Acceptance By The Bureau Of Corrections Of An Irrevocable Standby Letter Of Credit Of Equivalent Value From A Commercial Bank, A Bank Guarantee Or A Surety Bond Callable Upon Demand Issued By A Surety Or Insurance Company Duly Licensed By The Insurance Commission And Confirmed By The Bureau Of Corrections. 14 Materials And Equipment Delivered On The Site But Not Completely Put In Place Shall Not Be Included For Payment. 15.1 The Date By Which Operating And Maintenance Manuals Are Required Is Upon Actual Completion Of The Project. The Date By Which “as Built” Drawings Are Required Is Upon Actual Completion Of The Project. 15.2 The Amount To Be Withheld For Failing To Produce “as Built” Drawings And/or Operating And Maintenance Manuals By The Date Required Is Equivalent To Five Percent (5%) Of The Contract Price. Section Vi. Specifications Scope Of Works Item No. Description Amount 1.0 Earthworks 130,100.00 Scope Of Work: 1. Clearing And Grubbing Of The Proposed Site For The Project. 2. To Provide Suitable Filling Materials To Level The Existing Ground. Proper Compaction Must Be Observed. 3. Excavation Works For Column Footing And Wall Footing 4. To Provide Gravel Bedding For All Structure Layed Against The Soil/ground. 5. Backfilling And Compaction Of Excavated Soil. 2.0 Formworks 92,015.00 Scope Of Work: 1. Fabrication And Installation Of Forms For Column Pedestals. 2. Installation Of Shoring And Flat Forms For Erection Of Steel Columns 3.0 Concrete Works 322,700.00 Scope Of Work: 1. Concreting Of All Structural Reinforced Concrete Members (footing, Column Pedestal, Approach Beam, Wall Footing & Slab-on-grade) 2. All Column Footing & Slab Shall Be Laid In A Well Compacted Soil. 3. Minimum Concrete Cover Should Be Observed & Applied To All Members. 4. Provide 6" Chb Plastered Wall For Areas To Be Elevated From The Existing Ground To Attain Leveled Ground Surface. 4.0 Steel Reinforcement 135,030.00 Scope Of Work: 1. Fabrication Of Steel Reinforcements For All Structural Members. 2. Observed Correct/appropriate Bar Splicing For Each Steel Reinforcement Installation. Contract Duration: 210 Calendar Days Conforme: ___________________________________________ Name Of Company In Print ___________________________________________ Signature Over Printed Name Of Authorized Representative Scope Of Works Item No. Description Amount 5.0 Masonry Works 241,759.00 Scope Of Work: 1. Installation Of 6" Chb For Concrete Parapet Wall At The Back Of Each Parking Space. 2. Plastering Of Installed Chb Wall And Structural Surfaces. 3. Provide 6" Chb Plastered Wall For Areas To Be Elevated From The Existing Ground To Attain Leveled Ground Surface. 6.0 Roofing, Trusses & Other Steel Works 655,490.50 1. Installation Of Schedule 40, 4" Diameter G.i. Pipe For Columns 2. Installation Of 6" C-channel Steel Rafter. 3. Provide Strut Lateral Support For Columns. See Strut Details. 4. Installation Of 0.5mm Thick Corrugated G.i. Sheet Framed With 2"x4"x1.5mm C-purlins 5. Installation Of Roofing Accessories. 7.0 Painting Works 70,014.00 1. Painting Of All Exposed Masonry Surfaces. 2. To Provide Black-yellow Zebra Paint For Concrete Pedestal & Concrete Zocallo. 3. Painting Of All Steel Frames With Epoxy Paint Primer, With Enamel Black Paint For Top Coat. 4. Paint Of Corrugated G.i. Sheet With Red Oxide With Chocolate Brown Roofguard Topcoat. 5. Provide Black-yellow Zebra Paint For Steel Columns. 8.0 Electrical Works 38,226.50 1. Installation Of Flexible Hose And Wirings For Lighting & Outlets 2. To Use Outdoor Unit Convenience Outlets With Cover Estimated Direct Cost (edc) 1,685,335.00 Overhead, Contingencies, Miscellaneous (ocm), 10% 168,533.50 Contractor's Profit (cp), 10% 168,533.50 Value Added Tax (vat), 5% 101,120.10 Approved Budget For The Contract (abc) 2,123,522.10 Contract Duration: 210 Calendar Days Conforme: ___________________________________________ Name Of Company In Print ___________________________________________ Signature Over Printed Name Of Authorized Representative Section Vii. Drawings Contract Duration: 210 Calendar Days Conforme: ___________________________________________ Name Of Company In Print ___________________________________________ Signature Over Printed Name Of Authorized Representative Contract Duration: 210 Calendar Days Conforme: ___________________________________________ Name Of Company In Print ___________________________________________ Signature Over Printed Name Of Authorized Representative Contract Duration: 210 Calendar Days Conforme: ___________________________________________ Name Of Company In Print ___________________________________________ Signature Over Printed Name Of Authorized Representative Contract Duration: 210 Calendar Days Conforme: ___________________________________________ Name Of Company In Print ___________________________________________ Signature Over Printed Name Of Authorized Representative Contract Duration: 210 Calendar Days Conforme: ___________________________________________ Name Of Company In Print ___________________________________________ Signature Over Printed Name Of Authorized Representative Contract Duration: 210 Calendar Days Conforme: ___________________________________________ Name Of Company In Print ___________________________________________ Signature Over Printed Name Of Authorized Representative Contract Duration: 210 Calendar Days Conforme: ___________________________________________ Name Of Company In Print ___________________________________________ Signature Over Printed Name Of Authorized Representative Contract Duration: 210 Calendar Days Conforme: ___________________________________________ Name Of Company In Print ___________________________________________ Signature Over Printed Name Of Authorized Representative Section Viii. Bill Of Quantities Republic Of The Philippines Department Of Justice Bureau Of Corrections Leyte Regional Prison Abuyog, Leyte Project: Repair Of Lrp Motorpool (rebid) Bill Of Materials Quantity Unit Materials Unit Cost Total Amount I. Earthworks Works : 150 Cu.m Earthfill (ready Mix Material) 450.00 67,500.00 30 Cu.m Gravel G1 (gravel Bedding) 1,000.00 30,000.00 Material Cost ₱ 97,500.00 45 Cu.m Excavation 280.00 12,600.00 1.00 Lot Gravel Bedding 10,000.00 10,000.00 1.00 Lot Backfilling And Compaction 10,000.00 10,000.00 Labor/equipment Cost ₱ 32,600.00 Sub-total (mat'l, Labor & Equipment Cost) ₱ 130,100.00 Ii. Formworks : 7 Pcs Ordinary Plywood, Local Made, 1/2" 800.00 5,600.00 200 Pcs Coco Lumber, 2" X 2" X 12' 120.00 24,000.00 70 Pcs Coco Lumber, 2" X 3" X 12' 180.00 12,600.00 70 Pcs Coco Lumber, 2" X 4" X 12' 240.00 16,800.00 25 Kgs Cwn #4 85.00 2,125.00 25 Kgs Cwn #3 85.00 2,125.00 15 Kgs Cwn # 2 1/2 90.00 1,350.00 10 Kgs Cwn # 1 1/2 90.00 900.00 5 Pcs Nylon #100 45.00 225.00 Material Cost ₱ 65,725.00 Labor Cost ₱ 26,290.00 Sub-total (mat'l & Labor Cost) ₱ 92,015.00 Iii. Concrete Works : 475 Bags Portland Cement Type 1 280.00 133,000.00 50 Cu.m 3/4" Gravel, Crushed 1,250.00 62,500.00 35 Cu.m Coarse Sand 1,000.00 35,000.00 Material Cost ₱ 230,500.00 Labor Cost ₱ 92,200.00 Sub-total (mat'l, Labor & Equipment Cost) ₱ 322,700.00 Contract Duration: 210 Calendar Days Conforme: ___________________________________________ Name Of Company In Print ___________________________________________ Signature Over Printed Name Of Authorized Representative Iv. Steel Reinforcement : 75 Pcs 16mmø Rsb 440.00 33,000.00 360 Pcs 10mmø Rsb 165.00 59,400.00 40 Kgs No. 16 Tie Wire 90.00 3,600.00 5 Pcs Hacksaw Blade 90.00 450.00 Material Cost ₱ 96,450.00 Labor Cost ₱ 38,580.00 Sub-total (mat'l, Labor & Equipment Cost) ₱ 135,030.00 V. Masonry Works : 2,040 Pcs 6" Chb, Standard 22.00 44,880.00 320 Bags Portland Cement 280.00 89,600.00 18 Cu.m Fine Sand 1,000.00 18,000.00 110 Pcs 10mm Ø Deformed Bar 165.00 18,150.00 12 Kgs No. 16 Tie Wire 90.00 1,080.00 5 Roll Nylon #100 45.00 225.00 8 Roll Nylon #30 45.00 360.00 3 Mtrs Wire Mesh (sand Screen) 130.00 390.00 Material Cost ₱ 172,685.00 Labor Cost ₱ 69,074.00 Sub-total (mat'l & Labor Cost) ₱ 241,759.00 Vi. Roofing, Trusses & Other Steel Works: 25 Pcs 4" G.i. Pipe, Sched 40. 8,800.00 220,000.00 10 Pcs C-channel, 50x150x4.0mm 2,500.00 25,000.00 5 Pcs Tubular Bar, 50x100x1.5mm 1,400.00 7,000.00 27 Pcs 1 1/2" X 1 1/2" X 4mm Angle Bar 900.00 24,300.00 80 Pcs 2"x4"x1.5mm C-purlins 800.00 64,000.00 16 Pcs Sag Rod, 12mm X 6m Plain Bar 260.00 4,160.00 25 Pcs 1" X 1" X 4mm Angle Bar 550.00 13,750.00 12 Pcs 1" X 4mm Flat Bar 350.00 4,200.00 32 Pcs Pre-painted Fascia Cover, 0.5mm X 2.4m 400.00 12,800.00 96 Pcs Corr. G.i. Sheet, 0.5mm X 12' 820.00 78,720.00 32 Pcs Corr. G.i. Sheet, 0.5mm X 10' 630.00 20,160.00 2,400 Pcs Tex Screw, 2 1/2" 3.50 8,400.00 4 Box Blind Rivets, 1" X 5/32" 550.00 2,200.00 4 Pcs Vulcaseal 640.00 2,560.00 5 Pcs Hacksaw Blade 90.00 450.00 20 Pcs Welding Rod 160.00 3,200.00 5 Pcs Cutting Disc, 14" (for Metal) 390.00 1,950.00 Material Cost ₱ 492,850.00 Labor Cost ₱ 162,640.50 Sub-total (mat'l, Labor & Equipment Cost) ₱ 655,490.50 Contract Duration: 210 Calendar Days Conforme: ___________________________________________ Name Of Company In Print ___________________________________________ Signature Over Printed Name Of Authorized Representative Vii. Painting Works : 3 Gals Epoxy Primer W/ Catalyst 1,000.00 3,000.00 2 Gals Epoxy Paint Reducer 650.00 1,300.00 3 Gals Enamel Paint, Black 800.00 2,400.00 1 Gals Enamel Paint, Yellow 800.00 800.00 10 Sheets Sanding Paper, #100 50.00 500.00 1 Pcs Roller Brush, 7" 140.00 140.00 2 Pcs Paint Brush, 2 1/2" 75.00 150.00 2 Pcs Paint Brush, 4" 110.00 220.00 18 Gals Red Oxide 700.00 12,600.00 15 Gals Lacquer Thinner 600.00 9,000.00 20 Gals Roof Guard, Chocolate Brown 800.00 16,000.00 2 Gals Flat Latex Paint, White 750.00 1,500.00 2 Gals Semi-gloss Latex Paint, Black 800.00 1,600.00 1 Gals Semi-gloss Latex Paint, Yellow 800.00 800.00 Material Cost ₱ 50,010.00 Labor Cost ₱ 20,004.00 Sub-total (mat'l & Labor Cost) ₱ 70,014.00 Viii. Electrical Works: 120 Mtrs Flexible Hose, 1/2" 30.00 3,600.00 30 Pcs Flexible Hose Connector With Clip 13.00 390.00 1 Pcs 3/4" Pvc Long Elbow 90° 55.00 55.00 1 Pc 3/4" Conduit Pipe 150.00 150.00 1 Pc Entrance Cap 3/4" Dia. 120.00 120.00 20 Pcs Junction Box W/ Cover And Screw, 4" X 4" 65.00 1,300.00 5 Pcs Utility Box Deep Type, 2" X 4" 60.00 300.00 1 Box 2.0 Sq. Mm. Thhn Stranded Wire @150m/box 4,000.00 4,000.00 1 Box 3.5 Sq. Mm. Thhn Stranded Wire @150m/box 5,000.00 5,000.00 2 Set 2-gang Switch 345.00 690.00 2 Pcs 2-gang Convenience Outlet, Outdoor Type 450.00 900.00 8 Pcs Led T8 Linear Light Box Type 2x18watts (1.2m) With Housing 1,000.00 8,000.00 1 Set 6 Holes Panel Board, Plug - In, 2 Wire + Ground 1 - 100at 2p Mccb 2 - 30at, 2p Mccb 1 - 15at, 2p Mccb 4,500.00 4,500.00 5 Rolls Electrical Tape (big) 80.00 400.00 Material Cost ₱ 29,405.00 Labor Cost ₱ 8,821.50 Sub-total (mat'l & Labor Cost) ₱ 38,226.50 Contract Duration: 210 Calendar Days Conforme: ___________________________________________ Name Of Company In Print ___________________________________________ Signature Over Printed Name Of Authorized Representative Estimated Direct Cost (edc) ₱ 1,685,335.00 Overhead, Contingencies, Miscellaneous (ocm), 10% ₱ 168,533.50 Contractor's Profit (cp), 10% ₱ 168,533.50 Value Added Tax (vat), 5% ₱ 101,120.10 Approved Budget For The Contract (abc) ₱ 2,123,522.10 Contract Duration: 210 Calendar Days Conforme: ___________________________________________ Name Of Company In Print ___________________________________________ Signature Over Printed Name Of Authorized Representative Section Ix. Checklist Of Technical And Financial Documents Checklist Of Technical And Financial Documents I. Technical Component Envelope Class “a” Documents Legal Documents ⬜ (a) Valid Philgeps Registration Certificate (platinum Membership) (all Pages) In Accordance With Section 8.5.2 Of The Irr; Technical Documents ⬜ (b) Statement Of The Prospective Bidder Of All Its Ongoing Government And Private Contracts, Including Contracts Awarded But Not Yet Started, If Any, Whether Similar Or Not Similar In Nature And Complexity To The Contract To Be Bid; And ⬜ (c) Statement Of The Bidder’s Single Largest Completed Contract (slcc) Similar To The Contract To Be Bid, Except Under Conditions Provided Under The Rules; And ⬜ (d) Special Pcab License In Case Of Joint Ventures And Registration For The Type And Cost Of The Contract To Be Bid; And ⬜ (e) Original Copy Of Bid Security. If In The Form Of A Surety Bond, Submit Also A Certification Issued By The Insurance Commission Or Original Copy Of Notarized Bid Securing Declaration; And (f) Project Requirements, Which Shall Include The Following: ⬜ A. Organizational Chart For The Contract To Be Bid; ⬜ B. List Of Contractor’s Key Personnel (e.g., Project Manager, Project Engineers, Materials Engineers, And Foremen), To Be Assigned To The Contract To Be Bid, With Their Complete Qualification And Experience Data; ⬜ C. List Of Contractor’s Major Equipment Units, Which Are Owned, Leased, And/or Under Purchase Agreements, Supported By Proof Of Ownership Or Certification Of Availability Of Equipment From The Equipment Lessor/vendor For The Duration Of The Project, As The Case May Be; And ⬜ (g) Original Duly Signed Omnibus Sworn Statement (oss) And If Applicable, Original Notarized Secretary’s Certificate In Case Of A Corporation, Partnership, Or Cooperative; Or Original Special Power Of Attorney Of All Members Of The Joint Venture Giving Full Power And Authority To Its Officer To Sign The Oss And Do Acts To Represent The Bidder. Financial Documents ⬜ (h) The Prospective Bidder’s Computation Of Net Financial Contracting Capacity (nfcc). Class “b” Documents ⬜ (i) If Applicable, Duly Signed Joint Venture Agreement (jva) In Accordance With Ra No. 4566 And Its Irr In Case The Joint Venture Is Already In Existence Or Duly Notarized Statements From All The Potential Joint Venture Partners Stating That They Will Enter Into And Abide By The Provisions Of The Jva In The Instance That The Bid Is Successful. Ii. Financial Component Envelope ⬜ (j) Original Of Duly Signed And Accomplished Financial Bid Form; And Other Documentary Requirements Under Ra No. 9184 ⬜ (k) Original Of Duly Signed Bid Prices In The Bill Of Quantities; And ⬜ (l) Duly Accomplished Detailed Estimates Form, Including A Summary Sheet Indicating The Unit Prices Of Construction Materials, Labor Rates, And Equipment Rentals Used In Coming Up With The Bid; And ⬜ (m) Cash Flow By Quarter. X. Bidding Forms Company Letterhead Statement Of Ongoing Government & Private Contracts Repair Of Lrp Motorpool (rebid) Bid Reference No.: Bid2024-001 Statement Of All Its Ongoing Government And Or Private Contracts Including Contracts Awarded But Not Yet Started, If Any Whether Similar Or Not Similar In Nature. Name Of Contract Date Of Contract Contract Duration Owner’s Name And Address Nature Of Work Contractor’s Role (whether Sole Contractor, Subcontractor, Or Partner In A Jv) And Percentage Of Participation Total Contract Value At Award Date Of Completion Or Estimated Completion Time Value Of Outstanding Works Certified Correct: Name And Signature Of Authorized Representative Position Date Company Letterhead Statement Of Single Largest Completed Contract Repair Of Lrp Motorpool (rebid) Bid Reference No.: Bid2024-001 Statement Of Single (1) Largest Completed Contract Of Similar In Nature Within The Last Four (4) Years From The Date Of Submission And Receipt Of Bids Amounting To At Least Fifty Percent (50%) Of The Approved Budget Of The Contract (abc) Name Of Contract Date Of Contract Contract Duration Owner’s Name And Address Nature Of Work Contractor’s Role (whether Sole Contractor, Subcontractor, Or Partner In A Jv) And Percentage Of Participation Total Contract Value At Award Date Of Completion Or Estimated Completion Time Certified Correct: Name And Signature Of Authorized Representative Position Date Company Letterhead Repair Of Lrp Motorpool (rebid) Bid Reference No.: Bid2024-001 Republic Of The Philippines) City Of _______________________) S.s. X------------------------------------------------------x Bid Securing Declaration Invitation To Bid: [insert Reference Number] To: Leyte Regional Prison I/we, The Undersigned, Declare That: 1. I/we Understand That, According To Your Conditions, Bids Must Be Supported By A Bid Security, Which May Be In The Form Of A Bid-securing Declaration. 2. I/we Accept That: (a) I/we Will Be Automatically Disqualified From Bidding For Any Contract With Any Procuring Entity For A Period Of Two (2) Years Upon Receipt Of Your Blacklisting Order; And, (b) I/we Will Pay The Applicable Fine Provided Under Section 6 Of The Guidelines On The Use Of Bid Securing Declaration, Within Fifteen (15) Days From Receipt Of The Written Demand By The Procuring Entity For The Commission Of Acts Resulting To The Enforcement Of The Bid Securing Declaration Under Sections 23.1(b), 34.2, 40.1 And 69.1, Except 69.1(f), Of The Irr Of Ra 9184; Without Prejudice To Other Legal Action The Government May Undertake. 3. I/we Understand That This Bid Securing Declaration Shall Cease To Be Valid On The Following Circumstances: (a) Upon Expiration Of The Bid Validity Period, Or Any Extension Thereof Pursuant To Your Request; (b) I Am/we Are Declared Ineligible Or Post-disqualified Upon Receipt Of Your Notice To Such Effect, And (i) I/we Failed To Timely File A Request For Reconsideration Or (ii) I/we Filed A Waiver To Avail Of Said Right; (c) I Am/we Are Declared The Bidder With The Lowest Calculated Responsive Bid, And I/we Have Furnished The Performance Security And Signed The Contract. In Witness Whereof, I/we Have Hereunto Set My/our Hand/s This ____ Day Of [month] [year] At [place Of Execution]. [insert Name Of Bidder’s Authorized Representative] [insert Signatory’s Legal Capacity] Affiant Subscribed And Sworn To Before Me This ___ Day Of [month] [year] At [place Of Execution], Philippines. Affiant/s Is/are Personally Known To Me And Was/were Identified By Me Through Competent Evidence Of Identity As Defined In The 2004 Rules On Notarial Practice (a.m. No. 02-8-13-sc). Affiant/s Exhibited To Me His/her [insert Type Of Government Identification Card Used], With His/her Photograph And Signature Appearing Thereon, With No. ________ And His/her Community Tax Certificate No. _______ Issued On ____ At ______. Witness My Hand And Seal This ___ Day Of [month] [year]. Name Of Notary Public Serial No. Of Commission _______________ Notary Public For _______ Until __________ Roll Of Attorneys No. __________________ Ptr No. ______ [date Issued], [place Issued] Ibp No. ______ [date Issued], [place Issued] Doc. No. _____ Page No. _____ Book No. _____ Series Of _____ Company Letterhead Repair Of Lrp Motorpool (rebid) Bid Reference No.: Bid2024-001 Omnibus Sworn Statement Republic Of The Philippines ) City/municipality Of ______ ) S.s. Affidavit I, [name Of Affiant], Of Legal Age, [civil Status], [nationality], And Residing At [address Of Affiant], After Having Been Duly Sworn In Accordance With Law, Do Hereby Depose And State That: 1. Select One, Delete The Other: If A Sole Proprietorship: I Am The Sole Proprietor Or Authorized Representative Of [name Of Bidder] With Office Address At [address Of Bidder]; If A Partnership, Corporation, Cooperative, Or Joint Venture: I Am The Duly Authorized And Designated Representative Of [name Of Bidder] With Office Address At [address Of Bidder]; 2. Select One, Delete The Other: If A Sole Proprietorship: As The Owner And Sole Proprietor, Or Authorized Representative Of [name Of Bidder], I Have Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For Repair Of Lrp Motorpool (rebid) Of The Leyte Regional Prison As Shown In The Attached Duly Notarized Special Power Of Attorney; If A Partnership, Corporation, Cooperative, Or Joint Venture: I Am Granted Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For The Repair Of Lrp Motorpool (rebid) Of The Leyte Regional Prison, As Shown In The Attached [state Title Of Attached Document Showing Proof Of Authorization (e.g., Duly Notarized Secretary’s Certificate, Board/partnership Resolution, Or Special Power Of Attorney, Whichever Is Applicable;)]; 3. [name Of Bidder] Is Not “blacklisted” Or Barred From Bidding By The Government Of The Philippines Or Any Of Its Agencies, Offices, Corporations, Or Local Government Units, Foreign Government/foreign Or International Financing Institution Whose Blacklisting Rules Have Been Recognized By The Government Procurement Policy Board By Itself Or By Relation, Membership, Association, Affiliation, Or Controlling Interest With Another Blacklisted Person Or Entity As Defined And Provided For In The Uniform Guidelines On Blacklisting ; 4. Each Of The Documents Submitted In Satisfaction Of The Bidding Requirements Is An Authentic Copy Of The Original, Complete, And All Statements And Information Provided Therein Are True And Correct; 5. [name Of Bidder] Is Authorizing The Head Of The Procuring Entity Or Its Duly Authorized Representative(s) To Verify All The Documents Submitted; 6. Select One, Delete The Rest: If A Sole Proprietorship: The Owner Or Sole Proprietor Is Not Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; If A Partnership Or Cooperative: None Of The Officers And Members Of [name Of Bidder] Is Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; If A Corporation Or Joint Venture: None Of The Officers, Directors, And Controlling Stockholders Of [name Of Bidder] Is Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; 7. [name Of Bidder] Complies With Existing Labor Laws And Standards; And 8. [name Of Bidder] Is Aware Of And Has Undertaken The Following Responsibilities As A Bidder: A) Carefully Examine All Of The Bidding Documents; B) Acknowledge All Conditions, Local Or Otherwise, Affecting The Implementation Of The Contract; C) Made An Estimate Of The Facilities Available And Needed For The Contract To Be Bid, If Any; And D) Inquire Or Secure Supplemental/bid Bulletin(s) Issued For The Repair Of Lrp Motorpool (rebid). 9. [name Of Bidder] Did Not Give Or Pay Directly Or Indirectly, Any Commission, Amount, Fee, Or Any Form Of Consideration, Pecuniary Or Otherwise, To Any Person Or Official, Personnel Or Representative Of The Government In Relation To Any Procurement Project Or Activity. 1. In Case Advance Payment Was Made Or Given, Failure To Perform Or Deliver Any Of The Obligations And Undertakings In The Contract Shall Be Sufficient Grounds To Constitute Criminal Liability For Swindling (estafa) Or The Commission Of Fraud With Unfaithfulness Or Abuse Of Confidence Through Misappropriating Or Converting Any Payment Received By A Person Or Entity Under An Obligation Involving The Duty To Deliver Certain Goods Or Services, To The Prejudice Of The Public And The Government Of The Philippines Pursuant To Article 315 Of Act No. 3815 S. 1930, As Amended, Or The Revised Penal Code. In Witness Whereof, I Have Hereunto Set My Hand This __ Day Of ___, 20__ At ____________, Philippines. _____________________________________ Bidder’s Representative/authorized Signatory Subscribed And Sworn To Before Me This ___ Day Of [month] [year] At [place Of Execution], Philippines. Affiant/s Is/are Personally Known To Me And Was/were Identified By Me Through Competent Evidence Of Identity As Defined In The 2004 Rules On Notarial Practice (a.m. No. 02-8-13-sc). Affiant/s Exhibited To Me His/her [insert Type Of Government Identification Card Used], With His/her Photograph And Signature Appearing Thereon, With No. ________ And His/her Community Tax Certificate No. _______ Issued On ____ At ______. Witness My Hand And Seal This ___ Day Of [month] [year]. Name Of Notary Public Serial No. Of Commission _______________ Notary Public For _______ Until __________ Roll Of Attorneys No. __________________ Ptr No. ______ [date Issued], [place Issued] Ibp No. ______ [date Issued], [place Issued] Doc. No. _____ Page No. _____ Book No. _____ Series Of _____ Company Letterhead Repair Of Lrp Motorpool (rebid) Bid Reference No.: Bid2024-001 Certificate Of Net Financial Contracting Capacity (please Show Figures At How You Arrived At The Nfcc) This Is To Certify That Our Net Financial Contracting Capacity (nfcc) Is _____________________(p____________) Which Is At Least Equal To The Total Ceiling Price We Are Bidding. The Amount Is Computed As Follows: (please Show Computation Of Nfcc) Nfcc = (ca-cl) (15) – C Where: Ca = Current Assets Cl = Current Liabilities C = Value Of All Outstanding Or Uncompleted Portions Of The Projects Under Going Contracts, Including Awarded Contracts Yet To Be Started Coinciding With The Contract For This Project Note: The Values Of The Bidder’s Current Assets And Current Liabilities Shall Be Based On The Data Submitted To The Bir, Through Its Electronic Filing And Payment System (efps). (per Gppb Resolution No. 20-2013, July 13, 2013) Latest Annual Tax Return Must Be Attached To The Nfcc Computation That Was Filed Thru Electronic Filing And Payment Systems (efps) And Must Be Duly Validated With The Tax Payments Made Thereon For The Preceding Tax Year Be It On A Calendar Of Fiscal Year Income Per Revenue Regulations 3-2005 Issued This _______day Of __________2024. _______________________________________________ Name & Signature Of Authorized Representative ____________________ Position _______________ Date Company Letterhead Repair Of Lrp Motorpool (rebid) Bid Reference No.: Bid2024-001 Bid Form Date: Invitation To Bid No: To: Bids And Awards Committee Leyte Regional Prison We, The Undersigned, Declare That: (a) We Have Examined And Have No Reservation To The Bidding Documents, Including Addenda, For The Contract Repair Of Lrp Motorpool (rebid) At Leyte Regional Prison; (b) We Offer To Execute The Works For This Contract In Accordance With The Bid And Bid Datasheet, General And Special Conditions Of Contract Accompanying This Bid; The Total Price Of Our Bid, Excluding Any Discounts Offered Below Is: ________________________________________₱_________________; The Discounts Offered And The Methodology For Their Application Are: [insert Information]; (c) Our Bid Shall Be Valid For A Period Of 120 Calendar Days From The Date Fixed For The Bid Submission Deadline In Accordance With The Bidding Documents, And It Shall Remain Binding Upon Us And May Be Accepted At Any Time Before The Expiration Of That Period; (d) If Our Bid Is Accepted, We Commit To Obtain A Performance Security In The Amount Of 30% Percent Of The Contract Price For The Due Performance Of The Contract; (e) Our Firm, Including Any Subcontractors Or Suppliers For Any Part Of The Contract, Have Nationalities From The Following Eligible Countries; (f) We Are Not Participating, As Bidders, In More Than One Bid In This Bidding Process, Other Than Alternative Offers In Accordance With The Bidding Documents; (g) Our Firm, Its Affiliates Or Subsidiaries, Including Any Subcontractors Or Suppliers For Any Part Of The Contract, Has Not Been Declared Ineligible By The Funding Source; (h) We Understand That This Bid, Together With Your Written Acceptance Thereof Included In Your Notification Of Award, Shall Constitute A Binding Contract Between Us, Until A Formal Contract Is Prepared And Executed; And (i) We Understand That You Are Not Bound To Accept The Lowest Calculated Bid Or Any Other Bid That You May Receive. (j) We Likewise Certify/confirm That The Undersigned, Is The Duly Authorized Representative Of The Bidder, And Granted Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For The Construction Of Dialysis Center At New Bilibid Prison Of The Bureau Of Corrections. (k) We Acknowledge That Failure To Sign Each And Every Page Of This Bid Form, Including The Bill Of Quantities, Shall Be A Ground For The Rejection Of Our Bid. Name:_____________________________________________________________ In The Capacity Of:____________________________________________________ Signed:____________________________________________________________ Duly Authorized To Sign The Bid For And On Behalf Of:________________________ Date: ___________ Republic Of The Philippines Department Of Justice Bureau Of Corrections Leyte Regional Prison Abuyog, Leyte Schedule Of Prices Repair Of Lrp Motorpool (rebid) Bid Reference No.: Bid2024-001 Quantity Unit Materials Unit Cost Total Amount I. Earthworks Works : 150 Cu.m Earthfill (ready Mix Material) 30 Cu.m Gravel G1 (gravel Bedding) Material Cost ₱ 45 Cu.m Excavation 1.00 Lot Gravel Bedding 1.00 Lot Backfilling And Compaction Labor/equipment Cost ₱ Sub-total (mat'l, Labor & Equipment Cost) ₱ Ii. Formworks : 7 Pcs Ordinary Plywood, Local Made, 1/2" 200 Pcs Coco Lumber, 2" X 2" X 12' 70 Pcs Coco Lumber, 2" X 3" X 12' 70 Pcs Coco Lumber, 2" X 4" X 12' 25 Kgs Cwn #4 25 Kgs Cwn #3 15 Kgs Cwn # 2 1/2 10 Kgs Cwn # 1 1/2 5 Pcs Nylon #100 Material Cost ₱ Labor Cost ₱ Sub-total (mat'l & Labor Cost) ₱ Iii. Concrete Works : 475 Bags Portland Cement Type 1 50 Cu.m 3/4" Gravel, Crushed 35 Cu.m Coarse Sand Material Cost ₱ Labor Cost ₱ Sub-total (mat'l, Labor & Equipment Cost) ₱ Conforme: ___________________________________________ Name Of Company In Print ___________________________________________ Signature Over Printed Name Of Authorized Representative Quantity Unit Materials Unit Cost Total Amount Iv. Steel Reinforcement : 75 Pcs 16mmø Rsb 360 Pcs 10mmø Rsb 40 Kgs No. 16 Tie Wire 5 Pcs Hacksaw Blade Material Cost ₱ Labor Cost ₱ Sub-total (mat'l, Labor & Equipment Cost) ₱ V. Masonry Works : 2,040 Pcs 6" Chb, Standard 320 Bags Portland Cement 18 Cu.m Fine Sand 110 Pcs 10mm Ø Deformed Bar 12 Kgs No. 16 Tie Wire 5 Roll Nylon #100 8 Roll Nylon #30 3 Mtrs Wire Mesh (sand Screen) Material Cost ₱ Labor Cost ₱ Sub-total (mat'l & Labor Cost) ₱ Vi. Roofing, Trusses & Other Steel Works: 25 Pcs 4" G.i. Pipe, Sched 40. 10 Pcs C-channel, 50x150x4.0mm 5 Pcs Tubular Bar, 50x100x1.5mm 27 Pcs 1 1/2" X 1 1/2" X 4mm Angle Bar 80 Pcs 2"x4"x1.5mm C-purlins 16 Pcs Sag Rod, 12mm X 6m Plain Bar 25 Pcs 1" X 1" X 4mm Angle Bar 12 Pcs 1" X 4mm Flat Bar 32 Pcs Pre-painted Fascia Cover, 0.5mm X 2.4m 96 Pcs Corr. G.i. Sheet, 0.5mm X 12' 32 Pcs Corr. G.i. Sheet, 0.5mm X 10' 2,400 Pcs Tex Screw, 2 1/2" 4 Box Blind Rivets, 1" X 5/32" 4 Pcs Vulcaseal 5 Pcs Hacksaw Blade 20 Pcs Welding Rod 5 Pcs Cutting Disc, 14" (for Metal) Material Cost ₱ Labor Cost ₱ Sub-total (mat'l, Labor & Equipment Cost) ₱ Conforme: ___________________________________________ Name Of Company In Print ___________________________________________ Signature Over Printed Name Of Authorized Representative Quantity Unit Materials Unit Cost Total Amount Vii. Painting Works : 3 Gals Epoxy Primer W/ Catalyst 2 Gals Epoxy Paint Reducer 3 Gals Enamel Paint, Black 1 Gals Enamel Paint, Yellow 10 Sheets Sanding Paper, #100 1 Pcs Roller Brush, 7" 2 Pcs Paint Brush, 2 1/2" 2 Pcs Paint Brush, 4" 18 Gals Red Oxide 15 Gals Lacquer Thinner 20 Gals Roof Guard, Chocolate Brown 2 Gals Flat Latex Paint, White 2 Gals Semi-gloss Latex Paint, Black 1 Gals Semi-gloss Latex Paint, Yellow Material Cost ₱ Labor Cost ₱ Sub-total (mat'l & Labor Cost) ₱ Viii. Electrical Works: 120 Mtrs Flexible Hose, 1/2" 30 Pcs Flexible Hose Connector With Clip 1 Pcs 3/4" Pvc Long Elbow 90° 1 Pc 3/4" Conduit Pipe 1 Pc Entrance Cap 3/4" Dia. 20 Pcs Junction Box W/ Cover And Screw, 4" X 4" 5 Pcs Utility Box Deep Type, 2" X 4" 1 Box 2.0 Sq. Mm. Thhn Stranded Wire @150m/box 1 Box 3.5 Sq. Mm. Thhn Stranded Wire @150m/box 2 Set 2-gang Switch 2 Pcs 2-gang Convenience Outlet, Outdoor Type 8 Pcs Led T8 Linear Light Box Type 2x18watts (1.2m) With Housing 1 Set 6 Holes Panel Board, Plug - In, 2 Wire + Ground 1 - 100at 2p Mccb 2 - 30at, 2p Mccb 1 - 15at, 2p Mccb 5 Rolls Electrical Tape (big) Material Cost ₱ Labor Cost ₱ Sub-total (mat'l & Labor Cost) ₱ Total Bid Price ₱_________________________ Total Bid Price In Words _____________________________________________________________ Material Cost ₱ Sub-total ₱

Tender Id: consultation architecturale ouverte n°02/2024 | Architectural Study and Monitoring of the Construction Work of a Covered Parking Lot in the City of Chefchaouen