Drawer Tenders

Details: SET OF SEATS FOR L.H.B GS AMRIT BHARAT COACHES. FOLLOW CUSHIONING MATERIAL EITHER PU FOAM TO RDSO SPEC. RDSO/2007/CG-04 REV. 01 OR SILICON FOAM TO RDSO SPEC.RSDO/ 2013/CG-13 REV. 01 WITH FIRE PROPERTIES COMPLIANT TO R21 HL-3 OF EN45545 STANDARD AND U PHOLSTERY TO RDSO SPEC.RDSO/2008/CG-07 REV-NIL WITH AMENDMENT SLIP NO-5 WITH CORRIGEN DUM 1 OF MAY 2015. COLOUR SHADE TO BE FOLLOWED AS PER DESIGN LNO.MD46271 DATED 30.09. 24, as per Drawing: MPLSLSDD VERSION 1, Packing Instruction: ALL PROTRUDING PORTIONS OF SEAT/ BERTH SHOULD BE PROTECTED WITH ENVIRONMENT FRIENDLY PRE MOULDED THERMOCOL CAP OF R EQUISITE STRENGTH OR SILICON RUBBER CAP AS AN ALTERNATE OPTION. EACH INDIVIDUAL SEAT/BE RTH SHOULD BE COVERED WITH BIODEGRADABLE BUBBLE SHEET OF DIAMETER 10MM AND THICKNES S 30 MICRON ALL ROUND. FLAP OF BERTH SHOULD BE OUTSIDE THE BUBBLE SHEET PACKING LEAVIN G SEAT & BERTH MOUNTING UNCOVERED. THEN IT SHOULD BE WRAPPED ALL ROUND IN THICK LAMIN ATED JUTE FABRIC OF SUFFICIENT STRENGTH. THE ASSEMBLY SHOULD BE TIED WITH NYLON STRIPS. I T IS FURTHER WRAPPED WITH BIODEGRADABLE POLYTHENE ALL ROUND TO PREVENT INGRESS OF DU ST/WATER. FOR THE FOLLOWING ITEMS (IF COVERED UNDER S&B SET) THE ITEM-WISE PI (LATEST VER .) WILL BE AS UNDER : 1. CHAIR ANGLES, EXPANDED METAL PARTITION FRAME,SUSPENSION STRAPS, SUPPORTS AND MTG. BKT PI004 2. HARDWARE ITEMS PI019 3. ITEMS LIKE BEARING BKT, CHAIN BKT, C ATCH ARGGT, HINGE BKT AND SLEEVES ETC. PI020 4. LADDERS PI031, LUGGAGE RACKS PI042 A LIST SHOULD BE PASTED ON EACH BOX SHOWING PO NO, PL NO, DESCRIPTION, DRG NO, QTY, FIRM NAME & ADDRESS, DATE OF DISPATCH ETC NOTE : FIRMS HAVE OPTION TO PROVIDE QR CODE . THE ITEM S HELL CARRY A QR CODE ON CARDBOARD BOX NEAR THE MANUFACTURER NAME STICKER CONTAININ G THE DETAILS AS LISTED BELOW: " NAME OF THE MANUFACTURER " PURCHASE ORD ER NUMBER " PURCHASE ORDER DATE " UNIQUE SERIAL NUMBER (OR LOT NUMBE R FOR BULK ITEMS) OF THE MANUFACTURER OR " DATE OF MANUFACTUR E " DELIVERY CHALLAN NO. " DELIVERY CHALLAN DATE THE QR CODE SHALL BE AS PER ISO/IEC18004 MODEL2 AND THE DATA SHALL BE AVAILABLE AS XM L USING THE TAGS DETAILED ABOVE

Details: :seats For Lhb Non Ac Chair Car Coaches (108 Seater). Follow Cushioning Ma Terial Either Pu Foam To Rdso Spec. Rdso/2007/cg-04 Rev. 01 Or Silicon Foam To Rdso Spec . Rdso/2013/cg-13 Rev. 01 With Fire Properties Compliant To R21 Hl-3 Of En45545 Standard And Upholstery To Rdso Spec. Rdso/2008/cg-07 Rev-nil With Amendment Slip No-5 And Cor Rigendum 1 Of May 2015, As Per Drawing: Mdts-219 Rev.03 With Corrigendum No.1 Issued Vid E Letter No Md35131 Dt.31/01/22, Packing Instruction: Chair Car Seat( Ac & Nac ) : I. All Protr Uding Portions Of The Chair Car Seat Should Be Protected With Plastic Cover. 2.then Co Mplete Seat And Its Corners / Hand Rest/ Foot Rest Should Be Properly Wrapped With Bio Degradable Air Bubble Sheet Of Thickness 30 Micron And Bubble Diameter 10mm. 3. The Fu Ll Seat Should Be Further Wrapped With 3 Ply Corrugated Paper Sheet. 4. Each Individual Chair Should Be Covered All Around With Transparent, Plain, Biodegradable, Polythene Sheet To Prevent Ingress Of Dust/water. 5. The Seat Bottom Frame Portion Sh Ould Be Fitted With M.s Supports For Its Balancing, So That The Chair Can Rest On The Fl Oor Without Tilting On Any Side. 6. The Overall Packing Should Be Such That It Is Not Da Maged During Transportation Of The Material, The Seats Should Be Tied Up In Pairs Only. 7. All Hardware/accessories/loose Items In One Coach Set Should Be Separately Packed I N Wooden Box Having Sufficient Strength. 8. A List Should Be Pasted On Each Box Showi Ng Purchase Order No., Pl No., Description Of Item, Drg. No., Quantity, Firm Name, Addres S & Date Of Dispatch And Its Contents. Note : Qr Code Is To Be Affixed " Near Manufactur Er Name Plate On Each Seat " On Top Of Packed Seat As Per Pi Mentioned Above " On Top O F Wooden Box For Sr.no.7 Qr Code Having Details As Listed Below : 1 Name Of The Manufa Cturer 2 Purchase Order Number 3 Purchase Order Date 4 Unique Serial Number (or Lot Number For Bulk Items) Of The Manufacturer O R 5 Date Of Manufacture 6 Delivery Challan No. 7 Delivery Challan Date The Qr Code Shall Be As Per Iso/iec18004 Model2 And The Data Shall Be Available As Xml Using The Tags Detailed Above. Incase The Above Deta Ils Are Not Available, Or The Qr Codes Are Not Readable, The Supplied Material Is Liable To Be Rejected. [ Warranty Period: 84 Months After The Date Of Delivery ] ]

Description: BOQ ITEMS: Model showing relation of fimbriae and ovary, 9 day human blastocyst, 12 day human blastocyst, 13 day human blastocyst, Preovulatory follicle, Ovulation, Corpus luteum, Transverse sections through at various stages of development set of 3 models (A), Transverse sections through at various stages of development set of 3 models (B), Dorsal view of human embryo showing somites set of 2 models (A), Lateral view of human embryo showing bulging pericardial area set of 3 models(A), Lateral view of human embryo showing bulging pericardial area set of 3 models(C), Transverse section showing mesodermal germ layer set of 4 models (A), Transverse section showing mesodermal germ layer set of 4 models (B), Transverse section showing mesodermal germ layer set of 4 models (C), Ovum with board, Development human embryo 22nd days, Ovary with child, Development embryonic ovulation set of 5 models, Embryonic placenta previa set of 3 models, Embryo neural groove 26 days, Development embryo set of 10 models, Development of embryonic early blastocyst set of 4 models, The uterus at the time of implementation, Primordial follicle consisting of a primary oocytes surrounded by a layer of flattened epithelial cells on board (A) Primordial follicle, Primordial follicle consisting of a primary oocytes surrounded by a layer of flattened epithelial cells on board(B) Growing follicle , Type a spermatogonia derived from the spermatogonal stem cell population represent the firstcells in the process of spermatgenesis set of 43 models on board, Abnormal germ cells primordial follicle with two oocytes , Abnormal germ cells trinucleated oocytes , Abnormal germ cells various types of abnormal spermatozoa set of 5 models on board, Development of dizygotic twins normally each embryo has its own amnion chorion and placenta set of 8 models on board, Possible relations of fetal membranes in monozygotic twins set of 12 models on board, Fertilization pathway a succession of steps After a sperm binds to the zona pellucida set of five models on board, Development of embryo showing structures Passing through the primitive umbilical ring A) 5-week embryo , The intraembryonic coelom prior to body folding set of 5 model (3d), Successive stages in development of the respiratory four gut. (3d) a. at the end of the third week , uccessive stages in development of the respiratory four gut. (3d) forth week , Development of the chief branchi of the human lungs set of 6 models on board, Histological and functional , Various types of esophageal , Successive stages in development , Ventral view of coronal section of heart at level of atrioventricular canal showing development of veinous valves a, b, Development of conotruncal ridge & closure of interventricular foramen a , Development of viteline vein, umbilical vein a , c (2d), Development of viteline vein, umbilical vein a , b, c, d (3d), Development of inferior vena cava, Development of inferior vena cava, Development of inferior vena cava, Development heart 7 somites embryo, Development heart (set of 11 models) on the stand (3d), Transformation of the pericardioperitoneal canals into the pleural cavities set of 2 models (A), Embryonic aortic arch set of 3 models on stand (3d), Developments of the inferior vena cava azygos vein &superior (3d) vena cava Seventh week , Developments of the inferior vena cava azygos vein &superior (3d) vena cava The venous system at birth , Developments of the inferior vena cava azygos vein &superior (3d) vena cava Double inferior vena cava at the lumber level (clinical correlate) , Developments of the inferior vena cava azygos vein &superior (3d) Absent inferior vena cava (clinical correlate), Fetal circulation before birth (3D), Human circulation after birth (3D), Embryonic aortic arches 4th & 6th week a b, Embryonic aortic arch set of 3 models on board (2D), Primitive dosal & ventral mesentery (3d), Anterior view of intestinal loop showing coiling of small intestine set of 2 models, Rotation of midgut set of 7 models a, b, c, d, e, f, g, (big size) on stand (3d), Development of pancreas set of 5 models with stand, Development of embryo 4th and 5th weeks set of 2 models a b on stand (3d), Development stomuch embryo with pancreas and gall bladder (3d), Stomach nerve cutting section, Development of diaphragm set of 3 models A, Development of diaphragm set of 3 models B, Folding of caudal end of the embryo a b c, Body folding changes the shape of the intraembryonic coelom a, b, c, Separates the pericardial cavity from pleural cavity a, b, c, In the future thoracic region the septum transversum froms a ventral portion, Development of Digestive System , Intermediate mesoderm of pronephric, Relation of hindgut & cloaca (3d), Genital duct in male and female a, c with board, Sagittal section showing formation of uterus & vagina a b c, Vesico urethral portion of endodermal cloaca showing the sinus tubercle & fused paramesonephric duct (3d), Development of urogenital sinuss & formation of trigone of the bladder a, b, c, d (3d), Development of renal pelvis (kideny) set of 4 models a b d on stand (3d), Divisions of the cloaca into the urogenital sinus and ano rectal canal set of 3 models on stand (3d), The urethra is open on the ventral surface of the penis, Development of the external genitalia in the female & in the new born set of 2 models on board, Development of the external genitalia in the female on board., Development of the peritoneum (3d), Ascent of the kidney set of 3 models with stand a b c (3d), Indifferent stages of the external genitalia a b, Development of external genitalia in the male at 10 weeks set of 7 models, Hypospadias showing the various locations of abnormal urethral, Development of the external genitalia in the female at 5 months a b, Urorectal & rectovaginal fistulas set of 4 model, Pharyngeal arches with board, Frontal view of embryo showing stomodeum nasal placodes on frontonasal process A, Development of face a , c, d with board, Development of palate & roof of mouth set of 6 model (A,C,D,E,F), Frontal aspect of face showing nasal prominence maxillary prominence (A), Development of face cut section showing pharyngeal archs (3d), Development of the pharyngeal arches (a, b) , Thyroglossal cyst, Frontal section through the head of a 6.5 week embryo a b, Frontal section through the head of a 7.5 week embryo a b, Frontal section through the head of a 10 week embryo a b, Intermaxillary segment and maxillary processes a b, Development brain embryo -3D, Development of human brain (embryo) about mm (3d), Development brain (embryo) three month old(3d), Development brain (embryo) 13.6 mm long medial surface (3d), Development brain (embryo) about 10.2 mm (3d), Development brain (embryo) 13.6 mm long hind brain (3d), Development brain (embryo) set of 6 models (3d) A,B,D,E, Drawings illustration a variety of NTDS involving the spinal cord a b c d e, Neural crest cells penetrating the fetal cortex of the suprarenal gland a b, Sagittal section through the cephalic part of a 6 week embryo & 11TH & 16th week a b c, Formation of Ventral motor & dorsal sensory horns A B on board, Formation of the vertebral column at various stages of development a b c, Ventrolateral view of the optic cup & optic stalk of a 6 week embryo a b c

Description: BOQ ITEMS: Clearing jungle including uprooting of rank vegetation grass brush wood trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. , Demolishing R.C.C. work manually by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer in charge., Demolishing brick work manually by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer in charge. In cement mortar, Earth work in excavation by mechanical means Hydraulic excavator manual means in foundation trenches or drains not exceeding 1.5 m in width or 10 sqm on plan including dressing of sides and ramming of bottoms lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m. All kinds of soil., Excavation work by mechanical means Hydraulic excavator manual means in foundation trenches or drains not exceeding 1.5m in width or 10 sqm on plan including dressing of sides and ramming of bottoms lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soils as directed within a lead of 50 m Hard Rock, Filling available excavated earth excluding rock in trenches plinth sides of foundations etc. in layers not exceeding 20 cm in depth consolidating each deposited layer by ramming and watering lead up to 50 m and lift upto 1.5 m, Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering All work up to plinth level 1 isto 3 isto 6 where 1 Cement 3 coarse sand zoneIII 6 graded stone aggregate 20 mm nominal size, Supply mix place in position compact and cure cement concrete 1 isto 2 isto 4 1 cement 2 coarse sand 4 graded stone aggregate 20 mm nominal size below foundations walls wells pits trenches etc. and in basin lining as per specifications drawings and directions of the Engineer incharge and including cost of centring and shuttering and cement., Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering shuttering finishing and reinforcement All work up to plinth level 1 isto 1.5 isto 3 where 1 cement 1.5 coarse sand zoneIII 3 graded stone aggregate 20 mm nominal size , Brick work with common burnt clay F.P.S. non modular bricks of class designation 7.5 in foundation and plinth in Cement mortar 1 isto 6 1 cement 6 coarse sand, Centering and shuttering including strutting propping etc. and removal of form for Foundations footings bases of columns etc. for mass concrete, Steel reinforcement for R.C.C. work including straightening cutting bending placing in position and binding all complete upto plinth level Thermo Mechanically Treated bars of grade Fe500D or more, 15 mm cement plaster on the rough side of single or half brick wall of mix 1 isto 6 1 cement 6 fine sand Rates for external plastic are for height upto 10m from ground level in less otherwise stated, Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. for External work a. 15 mm dia nominal bore Preferable Make TATA or Jindal or as per direction of EIC, Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. for External work b. 20 mm dia nominal bore Preferable Make TATA or Jindal or as per direction of EIC, Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. for External work c. 25 mm dia nominal bore Preferable Make TATA or Jindal or as per direction of EIC, Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. for External work d. 50 mm dia nominal bore Preferable Make TATA or Jindal or as per direction of EIC, Providing and fixing gun metal gate valve with C.I. wheel of approved quality screwed end 20 mm nominal bore, Providing and fixing gun metal gate valve with C.I. wheel of approved quality screwed end 25 mm nominal bore, Providing and fixing gun metal gate valve with C.I. wheel of approved quality screwed end 50 mm nominal bore, Constructing masonry Chamber 30 into 30 into 50 cm inside in brick work in cement mortar 1 isto 4 1 cement 4 coarse sand for stop cock with C. I. surface box 100 into 100 into 75 mm inside with hinged cover fixed in cement concrete slab 1 isto 2 isto 4 mix 1 cement 2 coarse sand 4 graded stone aggregate 20 mm nominal size ic necessary excavation foundation concrete 1 isto 5 isto 10 1 cement 5 fine sand 10 graded stone aggregate 40mm nominal size and inside plastering with cement mortar 1 isto 3 1 cement 3 coarse sand 12mm thick finished with a floating coat of neat cement complete as per standard design With common burnt clay F.P.S. non modular bricks of class designation 7.5, Constructing masonry Chamber 60 isto 60 isto 75 cm inside in brick work in cement mortar 1 isto 4 1 cement 4 coarse sand for sluice valve with C.I. surface box 100mm top diameter 160 mm bottom diameter and 180 mm deep inside with chained lid and RCC top slab 1 isto 2 isto 4 mix 1 cement 2 coarse sand 4 graded stone aggregate 20mm nominal size ic necessary excavation foundation concrete 1 isto 5 isto 10 1 cement 5 fine sand 10 graded stone aggregate 40 mm nominal size and inside plastering with cement mortar 1 isto 3 1 cement 3 coarse sand 12 mm thick finished with a floating coat of neat cement complete as per standard design With common burnt clay F.P.S. non modular bricks of class designation 7.5, Constructing masonry Chamber 90 into 90 into 100 cm inside in brick work in cement mortar 1 isto 4 1 cement 4 coarse sand for sluice valve with C.I. surface box 100 mm top diameter 160 mm bottom diameter and 180 mm deep inside with chained lid and RCC top slab 1 isto 2 isto 4 mix 1 cement 2 coarse sand 4 graded stone aggregate 20 mm nominal size ic necessary excavation foundation concrete 1 isto 5 isto 10 1 cement 5 fine sand 10 graded stone aggregate 40 mm nominal size and inside plastering with cement mortar 1 isto 3 1 cement 3 coarse sand 12 mm thick finished with a floating coat of neat cement complete as per standard design With common burnt clay F.P.S. non modular bricks of class designation 7.5, Supply and laying of HDPE Pipe line 110mm dia complete in all respect as per direction of EIC