Institute Of Genomics And Integrative Biology Tender

2 x 2.5 sq.mm + 1 x 2.5sq.mm earth wire

Supply and fixing suitable size G.I Box with modular plate and cover in front on surface/recessed including P/F 3 pin 5/6 Amps modular socket outlet and 5/6Amps modular switch including , connections painting etc as required

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item) : With Toughened glass of 8 mm thickness

Shifting of existing IT server fixed on wall by opening and reifing to nearest wall with the help of FASTENERS/NUT/BOLTS/SCREWS etc.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm

Providing & Installing working desk made of 25 mm thick commercial board with 1.00 mm thick mica on both inner and outer side, moulding/bidding on the edges all around, commercial board 25 mm thick along with mica on both sides shall be continued all along vertically on back side (6feet 5 inches) and left side (6 feet 4 inches) except the front side. The vertical support of the same material shall be provided on these two sides with 3 feet interval, whereas on front side it will be supported by a stainless steel pipe of 50 mm dia resting on the floor. The height of the table top shall be 2.5 feet. Necessary holes in the boards are to be made for fixing the electrical fixtures. A 3 drawer pedestal made of the same material with lock is to be provided fro placing below the table. The table is to be made as per the dimensions in the drawing attached as Annexure-A with necessary minor modifications if required at site. The sample of the mica is to be approved by Department.

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 2nd class teak wood : 50 x 20 mm

2 x 6 sq.mm + 1 x 6 sq.mm earth wire

Wiring for circuit /sub-main wiring along with earth wirewith the following size of FRLS PVC Insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit/casing capping as required

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required : In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Supplying and fixing following way single pol and neutral seat steel MCB distribution board 240 V on surface/recess complete with tinned copper bus bar, neutral bus bar , earth bar ,din bar , inter connections, powder painted including earthlingetc. as required (but without MCB/RCCB/ISOLATOR)6 way , Double door

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

2 x 4 sq.mm + 1 x 4 sq.mm earth wire

Supplying and fixing following size / modules GI box along with modular base and cover plate for modular switches in recess etc. as required

Opening of Existing six nos. Godrej make workstations fixed with each other by separating top portin, Vertical Frame etc all complete along with transpoting up to 100 metre lead.

Supply and fixing suitable size G.I Box with modular plate and cover in front on surface/recessed including P/F 6 pin 15/16 Amps and 5/6 Amps modular socket outlet and 15/16Amps modular switch including , connections painting etc as required

Providing and fixing 2nd class teak wood lipping/ moulded beading or taj beading of size 18X5 mm fixed with wooden adhesive of approved quality and screws/ nails on the edges of the Pre-laminated particle board as per direction of Engineer-in-charge

Providing & Fixing 12.5 mm thick tapered edge gypsum moisture resistant board in MS partition frames with C.P.brass/stainless steel screws etc. Complete as per architectural drawings and directions of engineer-in-charges.

6 pin 15/16 A socket

Stainless Steel Butt Hinges, 125 x64 x1.9mm, IS: 12817 marked

Double poll

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

15/16 A switch

Providing and fixing expandable fasteners of specified size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/ R.C.C. and making good etc. Complete : 50 mm long

Supplying and fixing 5A to 32A rating 240/415V 10 KA ‘C” curve Miniature circuit breaker suitable for inductive load of following polls in the existing MCB DB complete with connections , testing and commissioning etc. as required

5/6 A switch

Single poll

Taking down carefully old electric point wiring as required , sub-main, switch board, Power Points and electrical fitting &fixture including all other electrical items taken under renovation area of room no – 110 ISSH building and 2ndfloor of DG-1 building and shifting of old materials as required and cutting of suitable size zipsum fall ceiling making good the damages with POP etc after fixing of LED light 4 x 1 panel complete in all respect as directed by engineer –In charge

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete

12 module (200 mm x 150 mm)

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS: 1378) : 250x10 mm

3 pin 5/6 A socket

Supplying and fixing Environmental friendly, new generation, aesthetically designed, ultra-modern recess mounting luminaire with high brightness SMD LEDs as light source, suitable for Armstrong/Grid ceiling 30 watts of Havells make model PLUTO NEO PANEL 4X1 cat no. PLUTONEO4X1PLR30WLED840S or its equivalent of Philips/ Bajaj /Crompton

Providing & Fixing Book Shelf on the wall made of 25 mm thick commercial board with 1.00 mm mica both inside and outside of size 1.0 m X 0.40 M X 0.33 m with a partition in centre. Each partition shall be provided with two nos. door of same material with lock facility. The bookshelf is to be hanged with the help of FASTENERS/NUT/BOLTS/SCREWS etc.

Wiring for light points / fan points /exhaust fan point / call bell points with 1.5 sq.mm FRLS PVC Insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit/casing capping , with modular switch modular plate , suitable box, and earthling the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required for group C

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron)

Extra for providing and fixing steel beading of size 10 x 10 x 1.6 mm (box type), approved shape and section with screws instead of glazing clips and metal sash putty, in steel doors, windows, ventilators and composite units.

Providing & fixing transparent Lamination/Film on Glass