Water Resources Department Tender

Supply of hydraulic oil grade 90 of approved make for operation of power pack including all lead and lifts and cost of all materials and as per directed by engineer in charge.complete with all leads and lifts and cost of all materials and as per directed by engineer in charge.

Supply Installation & comissioning of 10 KVA, 3 phase, AMF control panel, Liquid cooled Diesel Generator Set (make kirloskar/ mahindra/eicher) suitable for operating two gates at a time of 5 H.P. Motor & nearly 3 H.P. of lightning arrangement load including (Complete Operation from control room) testing complete with all lead and lifts transportation and as per directed by engineer in charge.

Supply & laying of all sizes of power cables required as per drawing for connecting between Main Distribution board, remote control desk and individual gate control panel situated above the gate hoist platform. All cables as per Is Standards of reputed made including testing, complete with all leads and lifts and cost of all materials and as per directed by engineer in charge.

Providing of Saftey equipments like 6 kg fire extinguisher 2 nos, megger 1 nos, hydaulic jack 30 ton capacity 02 nos, 1.1 kv gloves 2 set, torch, umbrella, tools set (inc. hammer, pliers set, screw driver sets, measuring tape, wrench) , 6 - 32 no spanner set ( both ring and D ), tester, 48 inch pipe wrench 2 nos. , digitel Multimeter, tool box, rubber mat, gumboot, raincoat. at site complete with all leads and lifts, transportation and cost of all materials and as per directed by engineer in charge.

Supplying, Installation, testing and commissioning of 40w, 80Wp Monocrystalline Panel - 12.8V 35 Ah Lithium Ferro Phsophate (LifePo4) battery hybrid solar street Iuminarie of housing made of extruded Aluminum and IP 65 ingress protection with street light pole bracket made out of 50 mm dia MS

Test & trial of individaul Gate after Overhauling/Greasing of rollers and their parts as required to make them free to rotate with its alignment & positioning work acccording to rubber seal/side guide roller/guide tee complete opening /fitting,nut bolt, lock plate etc. complete with all leads and lifts and cost of all materials and as per directed by engineer in charge. for 2 no. of under sluice gate

Painting of machinery, including gearing, housing, shafting, bearing, pedestals, oil tanks, control cabinets, hoist beams, pipe support, clams, ladders etc., of hoists and supporting structures, as per IS 14177-1994, for which surface preparation by blast cleaning of class ‘B’ Primer coat (one coat) of Zinc phosphate paint to give a minimum dry film thickness of 50 + 5 microns and finish coat (three coats) of aluminum paint to synthetic enamel paint, using airless spray, to provide a dry film thickness of 25+ 5 microns per coat. Thus, total dry film thickness of all the coats, including primer coat, should not be less than 125 microns. This will include expenses on mobilization and demobilization of equipments. For maintenance painting, the surface preparation shall be done by appropriate hand and power tool cleaning. Prior to hand and power tool cleaning, any heavy layer of rust should be removed by chipping. Visible oil, grease, dirt and other foreign material be cleaned using solvents like clean mineral spirits xylol or white gasoline. After hand and power tool cleaning, the surface should be cleaned of loose dust and debris and / or blast cleaned as laid down in Para 7.0 of IS Code 14177-1994. After the surface preparation, the primer and finishing coats shall be carried out as provided above for painting. (i) upto 1.5 m height Note: - The rates for item 1854 (i) & (ii) are applicable only for installed gates etc. For painting of non-installed gates etc., therates mentioned in 1854 (i) shall applicable with all leads and lifts and cost of all materials and as per specification and directed by Engineer in Charge.

Removing of old & damaged brake system. Providing & fixing of new 200 ø AC electro magnetic single phase brake 100% coil Rating class ''B'' insulation working on 400/440 V AC 50 Cycles/Sec for service and under sluice gates. complete with all leads and lifts and cost of all materials and as per directed by engineer in charge.

supply & laying of perforated cable trays (G.I.) with all supports, covers, bolts etc. including testing, complete with all leads and lifts and cost of all materials and as per directed by engineer in charge. Size 150x50 mm

Painting of unmachined surfaces, as per IS 14177-1994, for which surface preparation by blast cleaning of class ‘B’, primer coat (one coat) of chlorinated rubber based zinc phosphate primer, to provide a dry film thickness of 50 + 5 microns and finish coat (three coats) of vinyl resin/ chlorinated rubber, using airless spray, to provide a dry film thickness of 30 + 5 microns per coat. Thus, total dry film thickness of all coats including primer coat should not be less than 125 microns. This will include expenses on mobilization and demobilization of equipments. For maintenance painting, the surface preparation shall be done by appropriate hand and power tool cleaning. Prior to hand and power tool cleaning, any heavy layer of rust should be removed by chipping. Visible oil, grease, dirt and other foreign material be cleaned using solvents like clean mineral spirits xylol or white gasoline. After hand and power tool cleaning, the surface should be cleaned of loose dust and debris and / or blast cleaned as laid down in Para 7.0 of IS Code 14177-1994. After the surface preparation, the primer and finishing coats shall be carried out as provided above for painting. (i) upto 1.5 m height Note: - The rates for item 1854 (i) & (ii) are applicable only for installed gates etc. For painting of non-installed gates etc., therates mentioned in 1854 (i) shall applicable with all leads and lifts and cost of all materials and as per specification and directed by Engineer in Charge.

Providing and installation of 250 LPM/40 meter Head submersible moter pump in 150 mm. Dia bore with all material's suitable as per pump, pump/motor Delivery pipe, control Panel, M.S. clamp, Wooded panel board, Ammeter, Volt meter, Cable joint kit, G.I. bend, Earthing Kit and all misc item for installation of pump and moto complete with all leads and lifts, transportation and cost of all materials and as per directed by engineer in charge.

Designing and providing suitable RCC foundation in Cement Concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) including steel reinforcement form work, embeding 2 nos 50mm dia PVC pipe for cable entry in foundation, 4 nos 24mm dia foundation bolts of ENB grade 750mm long, excavation, disposal of surplus soil and curing etc. Supply and erection of 9 metre high, dia 155mm at bottom and 90mm at top, base plate size 260x260x16mm hot dipped galvanized (in single dip to minimum 75 micron octogonal pole made of 3mm thick steel grade E-350 sheet having window and flush cover with locking arrangement, 4 way terminal connector including 4mm thic anchor plate, and as per 15 2062 & BS EN: 10025. on RCC foundation duly Supplying, Installation, testing and commissioning of 06 Nos. - 60W, 90Wp Monocrystalline panel - 12.8V 52Ah Lithium Ferro Phosphate (LifePo4) battery hybrid solar street Iuminarie of housing made of extruded Aluminum and IP 65 ingress protection.with street light pole bracket on pole made out of 50 mm dia MS

Painting of structural components of hoist including supporting structures and surfaces of hydraulic hoists unexposed to water as per IS:14177-1994, for which surface preparation by blast cleaning of class ‘B’, primer coat (two coats) of Zinc phosphate primer to give dry film thickness of 40 + 5 microns per coat and finish coat (one color) of alkyd based micaceious iron oxide paint to give dry film thickness of 65 +5 microns followed by two coats of synthetic enamel paint, using airless spray, to give dry film thickness of 25 + 5 microns per coats, at an interval of 24 hours. Thus, total dry film thickness of all the coats, including primer coating, should not be less than 175 micros. This will include expensed on mobilisation and demobilisation of equipments. For maintenance painting, the surface preparation shall be done by appropriate hand and power tool cleaning. Prior to hand and power tool cleaning, any heavy layer of rust should be removed by chipping. Visible oil, grease, dirt and other foreign material be cleaned using solvents like clean mineral spirits xylol or white gasoline. After hand and power tool cleaning, the surface should be cleaned of loose dust and debris and / or blast cleaned as laid down in Para 7.0 of IS Code 14177-1994. After the surface preparation, the primer and finishing coats shall be carried out as provided above for painting. (i) upto 1.5 m height Note: - The rates for item 1854 (i) & (ii) are applicable only for installed gates etc. For painting of non-installed gates etc., therates mentioned in 1854 (i) shall applicable with all leads and lifts and cost of all materials and as per specification and directed by Engineer in Charge.

Dismantling structures like rolled steel, joists, I-section, T-section, Angles, channel sections etc. plates for beams, columns, All nuts and bolts should be stanchions, trusses, etc including stacking of serviceable materials and unserviceable materials separately and disposal of dismentaled items to specified place including all types of machineries, tools and tackles required complete with all lead and lifts and as per directed by engineer in charge.

Supplying and fixing Arrow type rubber seals and stainless steel counter shunk bolts, nuts, washers of approved quality including cost of all materials, removing of existing wornout/damaged Arrow type rubber seals from gates, clening surface making hole in new seals , Fixing new rubber seals/ bolts/nuts/washers tightly in position , scaffolding etc. complete with all leads and lifts and cost of all materials and as per directed by engineer in charge. Size As per sample size

Supply of Electric Hydraulic power pack (Motorized ) for operation of 20 MT emergency Hydraulic Hoist including compatible supply pipes as required at site complete with all lead and lifts and cost of all materials and as per directed by engineer in charge.

Cleaning, chipping, grinding in old welding joints and providing new welding joint including machining and labour cost. all types of machineries, tools and tackles required complete with all lead and lifts and as per directed by engineer in charge.

Providing and filling/ replacing gear oil of approved quality up to the required gauge level for Reduction gear unit of hoists/ gantry cranes including cost of all materials, machinery, labour etc. complete with all leads and lifts and cost of all materials and as per directed by engineer in charge. .

Supplying and fixing Z type rubber seals and stainless steel counter shunk bolts, nuts, washers of approved quality including cost of all materials, removing of existing wornout/damaged Z type rubber seals from gates, clening surface making hole in new seals , Fixing new rubber seals/ bolts/nuts/washers tightly in position , scaffolding etc. complete with all leads and lifts and cost of all materials and as per directed by engineer in charge. . Size 100x44x14mm

Removing , repairing and instalation of main rollers of gate dia 300 mm including reaming the existing roller to increase its internal dia if required so as remove any defect occured due to prolonged use of roller and providing cover plates,axial pin shaft,spacer ring,bearing,lock plate,oil seal etc. as per drawing as required to make them free to rotate complete with opening, fitting, machining oiling/greasing etc.complete with all leads and lifts and cost of all materials and as per directed by engineer in charge.

Supplying and fixing Flat rubber seals and stainless steel counter shunk bolts, nuts, washers of approved quality including cost of all materials, removing of existing wornout/damaged bulb type rubber seals from gates, clening surface making hole in new seals , Fixing new rubber seals/ bolts/nuts/washers tightly in position , scaffolding etc. complete with all leads and lifts and cost of all materials and as per directed by engineer in charge. . Size 76x12mm

Repairing of 20 MT emergency Hydraulic Hoist by Changing its O ring, Piston seals, Wear Rings cleaning barrel,cap port etc. complete with opening fitting including all lead and lifts and cost of all materials and as per directed by engineer in charge.

Providing and applying grease of approved quality to gate and hoist components requiring greasing as part of annual maintenance using grease gun wherever necessary including cost of all materials, machinery, labour, scaffolding etc. complete with all leads and lifts and cost of all materials and as per directed by engineer in charge. .

Providing and applying cardium compound of approved quality to wire ropes of hoists/ gantry cranes as part of annual maintenance including cost of all materials, machinery, labour etc. complete with all leads and lifts and cost of all materials and as per directed by engineer in charge. .

Supply & inatallation of Local control panel for PLC operation system suitable for remote control arrangement with all accessories like moisture control thermal heating system for panel and motor complete as per drawing for bay and under sluice gates (including providing & laying of all type suitable power cables & control signal wires with cable tray) suitable to mount outside at hoist plateform complete with all leads and lifts and cost of all materials and as per directed by engineer in charge.

Repairing of Hydraulic power pack for operation of 20 MT emergency Hydraulic Hoist by Changing its Pressure switch, pressure guage, Adaptor, valve, pump etc. complete with opening fitting including all lead and lifts and cost of all materials and as per directed by engineer in charge.

Painting of spillway gates, sluice gates, canal gates (both vertical or radial) stop logs, exposed embedded parts and all unmachined ferrous surfaces (hoist cylinder, cylinder heads, hydraulic piping, pipe fittings, bonnet covers), exposed to water, as per IS 14177-94, for which surface preparation by blast cleaning of Class “B”, primer coat (one coat) of inorganic Zinc silicate (preferable airless spray) or alternatively, two coats of zinc rich primer (containing not less than 85% zinc on dry film), to give dry film thickness of 70 + 5 microns and finish coat (two coats) of solvent less coal tar epoxy paint, using airless spray, to provide dry film thickness of 150 + 5 microns per coat. Thus, total dry film thickness of all the coats, including primer coating, should not be less than 350 microns. This will include expenses on mobilisation & demobilisation of equipments. For maintenance painting, the surface preparation shall be done by appropriate hand and power tool cleaning. Prior to hand and power tool cleaning, any heavy layer of rust should be removed by chipping. Visible oil, grease, dirt and other foreign material be cleaned using solvents like clean mineral spirits xylol or white gasoline. After hand and power tool cleaning, the surface should be cleaned of loose dust and debris and / or blast cleaned as laid down in Para 7.0 of IS Code 14177-1994. After the surface preparation, the primer and finishing coats shall be carried out as provided above for painting. (ii) Beyond 1.5 m height Note: - The rates for item 1854 (i) & (ii) are applicable only for installed gates etc. For painting of non-installed gates etc., therates mentioned in 1854 (i) shall applicable with all leads and lifts and cost of all materials and as per specification and directed by Engineer in Charge.