Water Resources Department Tender

Excavation in hard soil including 50m lead and 1.5m lift with dressing. Supplying and laying of 35 sq. mm PVC insulated heavy duty cables (conforming to I.S. 1554.1964) 1100 volts, grade 3.5 core, armoured of approved make with Supplying and laying of cement concrete of approved type of cover over L.T. cable in trench complete with all lead and lifts, cost of all materials and as per directed by engineer in charge.

Supply and erection with test & trial of Electrically operated Rope Drum Hoist( with inbuilt manual operation) of 20 MT capacity Hoist as per IS: 6938-2005 including transportation to site. complete with all lead and lifts, cost of all materials and as per directed by engineer in charge.

Providing and fixing of G.I.pipe 19 mm diameter 3 meter long duly fixed on wall / masonry in an approved manner for service entries, including Supplying installation, testing and commissiong of 30 watt 230/250 volts street light fittings with all accessories like drive, heat sink made of die cast alliminium with IP 66 protectionand 15KV surge protection on pole bracket , including connection, earthing, seperatehousing for driver etc complete with ‘T’ joint box with glands,Miniature circuit breakers Supplying of approved make and accepted standard miniature circuit breakers, suitable for 240/415 volts 50 cycle, A.C. supply 6 Amp. To 16 Amp. Rating suitable for 2 core PVC insulated heavy duty cables duly installed including making joints, connections, filling in with cable compound , complete with all lead and lifts, cost of all materials and as per directed by engineer in charge.

Providing casting machining and assembling of Cast Steel Rollers assembly complete with testing,including cost of all materials as cast steel rollers, stainless steel eccentric pin/shaft with square cut shape in one end for adjustment, lock plate, bronze bush, cover plate, nut bolts, machinery, labour, cutting, aligning, welding, finishing, cleaning, applying one coat of zinc rich epoxy primer and two coats of cold applied coal tar epoxy paint, etc., complete as per specifications and approved drawings with all lead and lifts, tools and tackles, including packing and forwarding, transportation charges for structural steel components and other materials.

Supplying and laying Second class T.M. open bhatta or pajawa burnt brick masonry in superstructure in cement mortar 1:6 - for Foundation and Wall including finishing and curing complete with all leads and lifts,Transportaion, cost of all materials and as per directed by engineer in charge.

Steel work in Tubular Structures as per approved design consisting of columns trusses, roof and bottom purling, base Plates, Holding down wind ties, bracings (if required) bolts, nuts and washers for fastening etc complete including labour Charge in all respect with all leads, lifts and cost of all materials complete as per directed by Engineer- in-charge.

Excavation in hard soil including 50m lead and 1.5m lift with dressing providing and Fixing foundation bolts 600mm long in Cement concrete 1:3:6 with graded metal of maximum size - 40 mm. Supply and erection of hot dipped galvanized (in single dip to minimum 75 micron octogonal pole made of 3mm thick steel grade E-350 sheet having window and flush cover with locking arrangement at suitable height from base fo cable termination block, pole suitably reinforced with welded steel section a window cut section to make the strength of pole unaffected, with followin minimum specifications with 4 way terminal connector including 4mm thic anchor plate, 4 nos 20mm dia foundation bolts of ENB grade, and as per 15 2062 & BS EN: 10025. (designed for wind speed upto 180km/hr, IS: 87 Part 3)
6 metre high, dia 130mm at bottom and 90mm at top, base plate size 200x200x12mm, on existing cement concrete foundation having grouted bolts and nuts, aligning in true vertical position, including Supplying installation, testing and commissiong of 45 watt 230/250 volts street light fittings with all accessories like drive, heat sink made of die cast alliminium with IP 66 protectionand 15KV surge protection on pole bracket , including connection, earthing, seperatehousing for driver etc , ‘T’ joint box with glands,Miniature circuit breakers Supplying of approved make and accepted standard miniature circuit breakers, suitable for 240/415 volts 50 cycle, A.C. supply 6 Amp. To 16 Amp. Rating suitable for 2 core PVC insulated heavy duty cables duly installed including making joints, connections, filling in with cable compound, complete with all lead and lifts, cost of all materials and as per directed by engineer in charge.

Supplying and laying 40mm thick Damp proof course of 1:2:4 (with 20mm gauge graded metal) covered with bitumen and sand (1 kg bitumen per Sq. m) including finishing and curing complete with all leads and lifts, Transportaion,cost of all materials and as per directed by engineer in charge.

Providing of Saftey equipments like 6 kg fire extinguisher 2 nos, megger 1 nos, hydaulic jack 30 ton capacity 02 nos, 1.1 kv gloves 2 set, torch, umbrella, tools set (inc. hammer, pliers set, screw driver sets, measuring tape, wrench) , 6 - 32 no spanner set ( both ring and D ), tester, 48 inch pipe wrench 2 nos. , digitel Multimeter, tool box, rubber mat, gumboot, raincoat. at site complete with all lead and lifts, cost of all materials and as per directed by engineer in charge.

Supplying, drawing and laying of 2x4 sqmm PVC Insulated cable of approved make in existing rigid steel conduit. (Surface or concealed) with Supplying and laying of cement concrete of approved type of cover over L.T. cable in trench complete with all lead and lifts, cost of all materials and as per directed by engineer in charge.

Painting two or more coats (excluding primer coat) on new surface with ready mixed paint of approved brand and manufacture in all shades to give an even shade. etc complete including labour Charge in all respect with all leads, lifts and cost of all materials complete as per directed by Engineer- in-charge.

Cleaning, chipping, grinding in old welding joints between gate element & splice plate, providing new 6-12 mm fillet welding including machining and labour cost. all types of machineries, tools and tackles required complete with all lead and lifts and as per directed by engineer in charge.

Excavation in hard soil including 50m lead and 1.5m lift with dressing includuing Supplying and laying of 10 sq. mm PVC insulated heavy duty cables (conforming to I.S. 1554.1964) 1100 volts, grade 2 core, armoured of approved make with Supplying and laying of cement concrete of approved type of cover over L.T. cable in trench complete with all lead and lifts, cost of all materials and as per directed by engineer in charge.

Supplying of approved make and accept-ed standard sheet steel enclosures(dust protected) for SP & N distribution ‘boards, including bus bar, neutral link, din bar suitable for incorporating M.C.B.surface/flush mounting type -’
(i) Up to 4 M.C. Bs per pole

Proving and fixing earthing arrangement with 600x600x6.3 mm galvanized iron plate electrode, including packing of charcoal powder and salt as per
specification, watering pipe 19 mm dia G.I. connections, etc. complete with refilling the pit as required, but excluding the excavation of earth pit. complete with all lead and lifts, cost of all materials and as per directed by engineer in charge.

Providing and Laying Cement Concrete 1:2:4 with graded metal of maximum size 20 mm. etc complete including labour Charge in all respect with all leads, lifts and cost of all materials complete as per directed by Engineer- in-charge.

Excavation in hard soil including 50m lead and 1.5 lift with dressing. etc complete including labour Charge in all respect with all leads, lifts and cost of all materials complete as per directed by Engineer- in-charge.

Providing, fabrication, machining with straightening and Erection work of gates, any parts of gate's and any accessories of gate's, Guide Tee, Track, Sealing frame, Leaf frame or any part of gate's, complete as per drawing with testing, including cost of all materials, with machinery, labour, tools and tackles cutting,aligning, welding, finishing, cleaning, etc.,applying one coat of zinc rich epoxy primer and two coats of cold applied coal tar epoxy paint, etc., complete as per specifications and approved drawings with all lead and lifts, including packing and forwarding, transportation charges for structural steel components and other materials.as per directed by engineer in charge.

Removing , repairing and instalation of main rollers of gate dia 300 mm including reaming the existing roller to increase its internal dia if required so as remove any defect occured due to prolonged use of roller and providing cover plates,axial pin shaft,spacer ring,bearing,lock plate,oil seal etc. as per drawing as required to make them free to rotate complete with opening, fitting, machining oiling/greasing etc. complete with all leads and lifts, Transportaion, cost of all materials and as per directed by engineer in charge.

Painting of structural components of hoist including supporting structures and surfaces of hydraulic hoists unexposed to water as per IS:14177-1994, for which surface preparation by blast cleaning of class ‘B’, primer coat (two coats) of Zinc phosphate primer to give dry film thickness of 40 + 5 microns per coat and finish coat (one color) of alkyd based micaceious iron oxide paint to give dry film thickness of 65 +5 microns followed by two coats of synthetic enamel paint, using airless spray, to give dry film thickness of 25 + 5 microns per coats, at an interval of 24 hours. Thus, total dry film thickness of all the coats, including primer coating, should not be less than 175 micros. This will include expensed on mobilisation and demobilisation of equipments. For maintenance painting, the surface preparation shall be done by appropriate hand and power tool cleaning. Prior to hand and power tool cleaning, any heavy layer of rust should be removed by chipping. Visible oil, grease, dirt and other foreign material be cleaned using solvents like clean mineral spirits xylol or white gasoline. After hand and power tool cleaning, the surface should be cleaned of loose dust and debris and / or blast cleaned as laid down in Para 7.0 of IS Code 14177-1994. After the surface preparation, the primer and finishing coats shall be carried out as provided above for painting. (i) upto 1.5 m height Note: - The rates for item 1854 (i) & (ii) are applicable only for installed gates etc. For painting of non-installed gates etc., therates mentioned in 1854 (i) shall applicable with all leads and lifts and cost of all materials and as per specification and directed by Engineer in Charge.

Painting of spillway gates, sluice gates, canal gates (both vertical or radial) stop logs, exposed embedded parts and all unmachined ferrous surfaces (hoist cylinder, cylinder heads, hydraulic piping, pipe fittings, bonnet covers), exposed to water, as per IS 14177-94, for which surface preparation by blast cleaning of Class “B”, primer coat (one coat) of inorganic Zinc silicate (preferable airless spray) or alternatively, two coats of zinc rich primer (containing not less than 85% zinc on dry film), to give dry film thickness of 70 + 5 microns and finish coat (two coats) of solvent less coal tar epoxy paint, using airless spray, to provide dry film thickness of 150 + 5 microns per coat. Thus, total dry film thickness of all the coats, including primer coating, should not be less than 350 microns. This will include expenses on mobilisation & demobilisation of equipments. For maintenance painting, the surface preparation shall be done by appropriate hand and power tool cleaning. Prior to hand and power tool cleaning, any heavy layer of rust should be removed by chipping. Visible oil, grease, dirt and other foreign material be cleaned using solvents like clean mineral spirits xylol or white gasoline. After hand and power tool cleaning, the surface should be cleaned of loose dust and debris and / or blast cleaned as laid down in Para 7.0 of IS Code 14177-1994. After the surface preparation, the primer and finishing coats shall be carried out as provided above for painting. (ii) Beyond 1.5 m height Note: - The rates for item 1854 (i) & (ii) are applicable only for installed gates etc. For painting of non-installed gates etc., therates mentioned in 1854 (i) shall applicable with all leads and lifts and cost of all materials and as per specification and directed by Engineer in Charge.

Painting of unmachined surfaces, as per IS 14177-1994, for which surface preparation by blast cleaning of class ‘B’, primer coat (one coat) of chlorinated rubber based zinc phosphate primer, to provide a dry film thickness of 50 + 5 microns and finish coat (three coats) of vinyl resin/ chlorinated rubber, using airless spray, to provide a dry film thickness of 30 + 5 microns per coat. Thus, total dry film thickness of all coats including primer coat should not be less than 125 microns. This will include expenses on mobilization and demobilization of equipments. For maintenance painting, the surface preparation shall be done by appropriate hand and power tool cleaning. Prior to hand and power tool cleaning, any heavy layer of rust should be removed by chipping. Visible oil, grease, dirt and other foreign material be cleaned using solvents like clean mineral spirits xylol or white gasoline. After hand and power tool cleaning, the surface should be cleaned of loose dust and debris and / or blast cleaned as laid down in Para 7.0 of IS Code 14177-1994. After the surface preparation, the primer and finishing coats shall be carried out as provided above for painting. (i) upto 1.5 m height Note: - The rates for item 1854 (i) & (ii) are applicable only for installed gates etc. For painting of non-installed gates etc., therates mentioned in 1854 (i) shall applicable with all leads and lifts and cost of all materials and as per specification and directed by Engineer in Charge.

Supply Installation & comissioning of 10 KVA, 3 phase, AMF control panel, Liquid cooled Diesel Generator Set (make kirloskar/ mahindra/eicher) suitable for operating two gates at a time of 5 H.P. Motor & nearly 3 H.P. of lightning arrangement load including (Complete Operation from control room) testingcomplete with all lead and lifts, cost of all materials and as per directed by engineer in charge.

Window side hung

Painting of machinery, including gearing, housing, shafting, bearing, pedestals, oil tanks, control cabinets, hoist beams, pipe support, clams, ladders etc., of hoists and supporting structures, as per IS 14177-1994, for which surface preparation by blast cleaning of class ‘B’ Primer coat (one coat) of Zinc phosphate paint to give a minimum dry film thickness of 50 + 5 microns and finish coat (three coats) of aluminum paint to synthetic enamel paint, using airless spray, to provide a dry film thickness of 25+ 5 microns per coat. Thus, total dry film thickness of all the coats, including primer coat, should not be less than 125 microns. This will include expenses on mobilization and demobilization of equipments. For maintenance painting, the surface preparation shall be done by appropriate hand and power tool cleaning. Prior to hand and power tool cleaning, any heavy layer of rust should be removed by chipping. Visible oil, grease, dirt and other foreign material be cleaned using solvents like clean mineral spirits xylol or white gasoline. After hand and power tool cleaning, the surface should be cleaned of loose dust and debris and / or blast cleaned as laid down in Para 7.0 of IS Code 14177-1994. After the surface preparation, the primer and finishing coats shall be carried out as provided above for painting. (i) upto 1.5 m height Note: - The rates for item 1854 (i) & (ii) are applicable only for installed gates etc. For painting of non-installed gates etc., therates mentioned in 1854 (i) shall applicable with all leads and lifts and cost of all materials and as per specification and directed by Engineer in Charge.

Removing of existing old remote control system parts like main distribution board,remote control desk,local control panel,cable,cable tray,wire,dial indicator etc. and Supply, Installation & comissioning with test trial of PLC operation system complete with 02 nos Local control panel for PLC operation system suitable for remote control arrangement with all accessories like moisture control thermal heating system for panel and motor complete as per drawing for under sluice gates, 01 nos Main distribution panel (placed in control room) with all arrangements duly fixed change over switch for D.G. set, 01 nos Remote control desk (placed in control room) with all acceessories for individual gate control & with a provision for digital gate position indicators,02 nos of Gate position sensor with up/ldown out of limit switch ( including dial indicator assembly) and all arrangements required for the PLC operation system of bay, under sluice and HR gates including providing & laying of all types suitable power cables and signal wires with cable trays complete with all lead and lifts, cost of all materials and as per directed by engineer in charge.

Filling foundation & around masonry works with hard soil or soft moorum including watering and ramming complete with all leads and lifts, cost of all materials and as per directed by engineer in charge.

Excavation of hard soil including material 1.5 mtr. Lift with dressing complete with all leads and lifts, cost of all materials and as per directed by engineer in charge. (size 5.1×0.6×0.8) & (3×0.6×0.8)

Providing class 1 corrugated galvanized iron sheet roofing, fixed with G.I. J. or L Hooks, bolts & nuts 8mm dia with bitumen and G.I.J. Limpet washers or with G.I. limpet washers filled with white lead complete, excluding wind tiles, wooden scantling, hips & ridges with 0.80 mm thick sheet.etc complete including labour Charge in all respect with all leads, lifts and cost of all materials complete as per directed by Engineer- in-charge.

Supplying and fixing Flat rubber seals and stainless steel counter shunk bolts, nuts, washers of approved quality including cost of all materials, removing of existing wornout/damaged bulb type rubber seals from gates, clening surface making hole in new seals , Fixing new rubber seals/ bolts/nuts/washers tightly in position , scaffolding etc. complete. Size 76x12mm

Fabrication, supply and erection of fixed wheel/sliding type structural steel vertical lift gates for canal size 2.25 m x 1.5 m with gate leaf (complete with skin plate,stiffeners, guide etc.) embedded parts (first stage anchors sill beam fitted with S.S. plate, seal frame fitted with S.S. plate, guide tee etc). rubber seals as per IS: 4622 duly painted as per SOR item 1854 with screw hoist, hoisting rod, guide, hoist support structure etc. complete with all lead and lifts, cost of all materials and as per directed by engineer in charge.

Supplying and fixing bulb type (musical note) teflon cladded rubber seals and stainless steel counter shunk bolts, nuts, washers of approved quality including cost of all materials, removing of existing wornout/damaged bulb type rubber seals from gates, clening surface making hole in new seals , Fixing new rubber seals/ bolts/nuts/washers tightly in position , scaffolding etc. complete. Size 100x40x12mm

Supplying and laying Cement Concrete 1:3:6 with graded metal of maximum size 40 mm. in foundation including finishing and curing complete with all leads and lifts, Transportaion, cost of all materials and as per directed by engineer in charge. size (5.1×0.6×0.3) & (3×0.6×0.3)

Steel work in single section including forging and hoisting, fixing in position etc. complete (b) in angles,channals flats and tee complete with all lead and lifts, cost of all materials and as per directed by engineer in charge.

Supplying and laying 15mm thick cement plaster on brick work in C.M. 1:4 including finishing and curing complete with all leads and lifts, Transportaion,cost of all materials and as per directed by engineer in charge.

Filling in plinth the material obtained from spoils including watering and ramming in 15 cm layers including 50 m lead and 1.5 m lift complete with all leads and lifts, cost of all materials and as per directed by engineer in charge.

Dismantling structures like rolled steel, joists, I-section, T-section, Angles, channel sections etc. plates for beams, columns, All nuts and bolts should be stanchions, trusses, etc including stacking of serviceable materials and unserviceable materials separately and disposal of dismentaled items to specified place including all types of machineries, tools and tackles required complete with all lead and lifts and as per directed by engineer in charge.

Providing and fixing steel glazed doors, windows and ventilators of standard rolled steel sections, joints mitred and welded with 15x3 mm lugs 10cm long, with steel lugs, embedded in cement concrete blocks 1x15x10cm of 1:3:6 with 20mm graded metal or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required including providing and fixing of glass panes with glazing clips and special metal sash putty of approved make complete including Applying a priming coat of approved steel primer, excluding the cost of metal beading and other fittings except necessary hinges or pivots as required complete with all lead and lifts, cost of all materials and as per directed by engineer in charge.
Door