Institute Of Microbial Technology Tender

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.

Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required. 4 Zone

6 Zone

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 2850 lpm at 70 m Head Note: * The head of the pump is selected in a manner so as to give a minimum 3.5kgf/cm 2 pressure at the highest/farthest point.

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 450 lpm at 35 m Head

Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted/ Wall mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following Incoming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required :INCOMING: 400A, 50kA 4 Pole MCCB, Ics=100% Icu rating Digital Voltmeter 0-500V with selector switch Ammeter (0-400 A) with selector swtich & CTs etc. LED type RYB phase indicating lamps, ON, OFF, trip indicating lamps Set of Copper Bus Bar 500A Outgoings ( Note : All outgoing feeders for pumps should have digital Ammeter with selector switches, and LED type ON, OFF, trip indicating lamps) Main Fire Pump 200 A, 50kA TPN MCCB, Ics=100% Icu, with fully automatic Star/Delta starter suitable for 75 hp pump with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation, selector switch for local/remote, auto/manual/OFF operation. Jockey Pump 100 A, 50kA TPN MCCB, Ics=100% Icu, with suitable HP fully automatic Star/Delta starter with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation, selector switch for local/remote, auto/manual/OFF operation. Diesel Engine Control: Control for diesel engine comprising - Automatic/Manual selctor switch & 3 attempt starting device, timers and relays as required, push buttons, start/stop in manual mode Indicating lamp for high/ Low Lub. Oil pressure, High Water Temp and Engine on indication Battery charger suitbale for 12V/24 V DC with boost and trickle selector switch, 0-30 V DC volt meter, and 0- 20 A DC Ammeter All standard relays and accessories for automatic operation of diesel engine System Controller Designing, Supply, Installation, Testing and commissioning of system controller to control operation of main electric fire pump, diesel pump, Pressurization pump, Terrace pump in sequence as per specification consisting of relays, timers. Sensors, annunciation window for fault indication, complete as per specifications.Diesel Engine Control: Control for diesel engine comprising - Automatic/Manual selctor switch & 3 attempt starting device, timers and relays as required, push buttons, start/stop in manual mode Indicating lamp for high/ Low Lub. Oil pressure, High Water Temp and Engine on indication Battery charger suitbale for 12V/24 V DC with boost and trickle selector switch, 0-30 V DC volt meter, and 0- 20 A DC Ammeter All standard relays and accessories for automatic operation of diesel engine System Controller Designing, Supply, Installation, Testing and commissioning of system controller to control operation of main electric fire pump, diesel pump, Pressurization pump, Terrace pump in sequence as per specification consisting of relays, timers. Sensors, annunciation window for fault indication, complete as per specifications. SYSTEM CONTROLLER Designing, Supply, Installation, testing & commissioning of system controller to control operation of main electric fire pump, diesel pump, pressurization pump, Terrace pump in sequence as per specyfication consisting of relays, timers. Sensors, annunciation window for fault indication, complete as per specification.

Providing, laying, testing & commissioning of 'C' class (Jindal Hissar, Tata make) heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 25mm dia

50mm dia

65mm dia

80 mm dia

100 mm dia

150mm dia

200mm dia ( wall thickness 6.3mm)

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal Steel

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 50mm dia

80 mm dia

100mm dia

150mm dia

200mm dia

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required : 80mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required: 80mm dia

100 mm dia

150mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 80mm dia

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Gunmetal

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30m

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Supplying, installation, testing & commissioning of deluge valve (to be used for water curtains) UL listed with wet pilot basic trim assembly for DVA with test and alarm, drip and drain valve with water motor gong complete as required. 80mm dia

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in: Cement mortar 1:6 (1 cement : 6 coarse sand)

15 mm cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall.

Painting (two or more coats) on rain water, soil waste and vent pipes and fittings with synthetic enamel paint of approved brand (Asian, Nerolac, ICI Dulux) and manufacture and required colour over a priming coat of approved steel primer on new work. 100 mm diameter pipes

150 mm diameter pipes

Painting (one or more coats) on rain water, soil waste and vent pipes, fire pipes and fittings with synthetic enamel paint of approved brand (Asian, Nerolac, ICI Dulux) and manufacture and required colour on old work : 75 mm diameter pipes

100 mm diameter pipes

150 mm diameter pipes

Painting with synthetic enamel paint of approved brand (Asian, Nerolac, ICI Dulux) and manufacture of required colour to give an even shade: One or more coats on old work

Providing & fixing G.I. Pipes (Jindal hissar-B class, Tata-B class) complete with G.I. fittings & clamps,i/c cutting & making good the walls etc. 32mm dia nominal bore

40mm dia nominal bore

50mm dia nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing & fixing tee, including cutting & threading the pipe etc. complete. 25 to 40mm nominal bore

Providing & fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 32mm nominal bore

40mm nominal bore

50mm nominal bore

Providing and fixing ball valve(brass) of approved quality high or low pressure with plastic floats complete. 25mm dia

Painting G.I. Pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality. 32mm diameter pipe

40mm diameter pipe

50mm diameter pipe

Providing and fixing G.I. Union (SVW, UNIK make) in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 32mm nominal bore

40mm nominal bore

50mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.Make- Sintex, Diplast ISI mark)

Supplying, installation, testing & commissioning sector panel (Agni, Honeywell, Ases make) suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required. 16 Zone

Providing and fixing of fire evacuation layout plans (Exit plan of each floor) made up of 3mm thick Acrylic Sheet (photoluminescent type) fixed on walls at different levels of the building of size (600mm x 450mm) with suitable fasteners, nut bolts etc complete in all respect printing in blue and black or other colour combination including subject matter & instructions in bi-lingual ,symbols and borders as per the direction of Engineer-in-charge. (Area of acrylic sheet is to be measured for payment).

Providing & fixing first aid fire hose reel 30 mtr long high pressure Nylon braided thermoplastic hose ID 20mm as per IS: 12585 Type II, CM/L No. 8958212 with ISI Marked working : 10.2kg/cm, 6mm bore shut-off plastic nozzle, confirming to IS:884, with ISI marked with shut off nozle.

Providing & fixing Hose box, wall mounting type, made out of mild steel sheet 120swg, 30 inchx24 inchx 10 inch size to accommodate two 15mtr or 30 mtr length of delivery hose & a branch pipe, glass fronted Double door with lock, two keys & painted fire red outside & white inside complete in all respect as per the direction of Engineer-in-Charge.

Providing & fixing jublee clamp of required size including screws etc. complete in all respect as per the direction of Engineer-in-Charge.

Providing & fixing flexible pipe 1 to 1.5 mtr long connected with Co2 extinguisher etc. complete in all respect as per the direction of Engineer-incharge.

Providing & fixing Hose reel drum (Safegaurd/Minimax/ Firecon make) swinging wall mounting type, CM/L No.8958212 with ISI marked confirming to IS:884 complete in all respect as per the direction of Engineer-incharge.

Providing & fixing ball valve (brass) of approved quality (, high or low pressure, with plastic floats complete. 32mm nominal bore

Providing & fixing of four core Aluminium armoured cable of 16 sqmmx 4Core dia fitted with reqd size thimbles, Glands etc. complete in all respect for installation of pump set from the mains.

Supplying, laying, testing and commissioning of MS made cubicle panel made out of 1.6mm CRCA sheet powder coated with siemens color. The panel is design for wall mounting type with cable incoming and out goings from bottom. All the switchgear are from L&T /Schneider/Eaton Make MCB TP 32A, Contractor MNX-12A., Over load relay 4.5-7 5A, ON/OOF indication, STOP/START Push Button, Auto/Manual Switch, Terminal STRIP, MBC 1 POLE 6 Amp, Aux. Cont., SDS Timer, SPPR, Enclosure & accessories fabrication in 1.6mm. CRCA Sheet powder coating in Siemens Gray Shede, 75X40MM. Channel Base Frame, Cable Entry will be Top & Bottom Suitable for Cable Lock, Rubber Gasket, hardware etc. Wiring & Accessories Power & Control wiring will be (ISI 1100V) flamo smoke FRLS PVC Singte Core Copper Wire Copper Lugs, PVC Steeve, Ferruels Numbers, Hardware & Lbour etc. including Starter suitable for 7.5 Hp mortar.

Supply & installation CO2 type fire extinguisher 4.5kg capacity Fire extinguishers made From new seamless cylinder DOE & CCE Nagpur approved type Fitted with discharge hose & horn and wheel type valve with Initial charge as per IS: 15683 specification ISI Marked FIRE RATING 34B WORKING PRESSURE 60KGF/CM2 HYDRO PRESSURE 250KGF/CM2 BURSTING PRESSURE 600KGF/CM2

Supply & installation ABC Stored Pressure type fire extinguisher 2kg Capacity having Dry Chemical Powder(MAP 40%) IS: 4308 for Fighting A.B & C Class Fire rating, test pressure 30kg/cm2 mild steel body pressurized By Nitrogen Gas. The Extinguisher has pressure gauge for indicating inside Pressure with opening and closing Lever of squeeze grip valve with tamper Proof seal. Extinguisher is externally Epoxy coated as per IS: 5 Colors shadeNo.538 complete with wall Bracket. The Extinguisher will be manufactured strictly as per BIS: 15683 bearing ISI Marked. FIRE RATING 2A, 34B WORKING PRESSURE 15KGF/CM2 HYDRO PRESSURE 35KGF/CM2 BURSTING PRESSURE 55KGF/CM2

Supply & Installation ABC Stored Pressure type fire extinguisher 6kg Capacity (Safex, Minimax, Ceasefire make) having Dry Chemical Powder (MAP 40%) IS: 4308 for Fighting A.B & C Class Fire rating, test pressure 30kg/cm2 mild steel body pressurized By Nitrogen Gas. The Extinguisher has pressure gauge for indicating inside Pressure with opening and closing Lever of squeeze grip valve with tamper Proof seal. Extinguisher is externally Epoxy coated as per IS: 5 Colors shadeNo.538 complete with wall Bracket. The Extinguisher will be manufactured strictly as per BIS: 15683 bearing ISI Marked. FIRE RATING 4A, 89B WORKING PRESSURE 15KGF/CM2 HYDRO PRESSURE 35KGF/CM2 BURSTING PRESSURE 55KGF/CM2

Standard response standard spray Brass sprinklers with Nickel chrome plated finish - K 80 T - 68 deg.c, 1/2" end connection. (Make-HD/Viking/Tyco).

Supply, installation, testing & commissioning of High Velocity Water spray nozzles Brass MOC K-26, end connection 1/2" / 3/4" BSPT, 1000 angle with UL Listed.

Dismantling, re-installation, testing & re-commissioning of existing smoke detectors, manual call point & hooter etc. complete in all respect as per the direction of EIC.

Dismantling & buy back of existing Diesel engine control panel consisting of charger , Relays, fuses etc including termination of cables & glands installed at PUMP House of IMTECH including enclosure & all necessary accessories complete in all respect as per the direction of Engineer-in-Charge.

Dismantling & buy back of existing main pump control panel consisting of switch 250Amp, CT 200/5, Bus bar , ML-6 contactor, overload relay & timer etc. complete including termination of cables & glands installed at PUMP House of IMTECH including enclosure & all necessary accessories complete in all respect as per the direction of Engineer-in-Charge.

Dismantling & buy back of existing Jockey pump control panel consisting of FN switch 250Amp, Timer, ML-1 contactor, overload relay , Amp & Volt meter display etc. complete including termination of cables & glands installed at PUMP House of IMTECH including enclosure & all necessary accessories complete in all respect as per the direction of Engineer-in-Charge.

Dismantling & buy back of 62.5 KVA (Kirloskar make) old DG Set Model RB-66 installed at Pump House of IMTECH complete in all respect as per the direction of Engineer-in-Charge.