Directorate Of Technical Education Tender

The seat and back are made up of 1.2+/-0.1cm thick hot pressed plywood measured and upholstered with black leather cloth and moulded polyurethane foam The back foam is designed with contoured lumbar support for extra comfort.The High resilience polyurethane foam is moulded with density 45+/-2 kg/m3 and hardness load 16+/-2 kgf as per IS:7888 for 25% compression.The desklet is hinged type and made of medium densityfiberboard and bottom side provided with backing laminate.

The dimension of the table is 1199mm W x 590mm D x 750mm H. The worktop is made of 18mm Thick pre laminated board (PLB) and the worksurface edges are duly sealed with 2 mm thick Pre PVC Beading. The understructure is made of CRCA MS Sheet of 0.9mm Thick and the tubular frame is made of ERW Square tubes of size 25.4mm x 25.4mm x 1.2mm Thick. The modesty panel is made of 1.0mm Thick CRCA MS Sheet. The shell of the drawer unit is made of 0.5mm thick CRCA MS. There is one drawer .The drawer tray is made of 0.6mm thick CRCA MS and the drawer front is made of 0.8mm Thick CRCA MS Sheet. Manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and should have Green Guard Certification for few of its products.

The seat and back should be made from 1.2 +/- 0.1cm thick hot pressed plywood measured as per QA method and laminated with natural veneer in three different shades of teak and mahogany.Back size : 42 cm (W) x 45cm (H), merging down into seat.Seat size : 44cm (W) x 40cm (D) , merging up into back. The understructure should be made of MS tube of dia 1.9 +/-0.02cm x 0.16 +/-0.0128 cm thk , of black powder coated (DFT 40-60 microns). The understructure should be provided with PVC ferrules. Manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and should have Green Guard Certification for few of its products.

The main top should be 1800mm (W) x 795mm (D) of dimension. It should be made of 25 mm top +15 mm frame thick particle board with 0.45 mm PVC edge banding.The modesty panel should be of dimension 1100mm (W) x 405mm (D).The top of the modesty should be 18mm thk particle board with 0.45mm PVC edge banding. The drawer front should be of dimension 495mm (W) x 170mm(D), made of 18mm thk particle board with 0.8 mm PVC edge. The KBPT should be of dimension 580mm (W) x 285mm(D) , along with 18mm top thickness, with 0.45mm PVC edge banding.The ERU should be of dimension 1600mm(L) x 500mm(W)x 640mm(H).Overall Dimension : 2100mm (W) x 727mm (D) x 765mm (H). Manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and should have Green Guard Certification for few of its products.

It should be a desk-based system built for simplicity and flexibility. It is designed such that it looks minimal yet takes care of every little detail. Finish- - opaque finish like laminate or pre-laminate boards.Structure -The Understructure comprises of Leg Assemblies and Cross connectors. Over this matrix of Legs and Cross connectors, the work-surfaces are fixed.The ends of the work surface are chamfered.It should contain one right leg, one left leg and one shared leg, alon.Dimension :2100mm (W) X600mm (D)x750mm (H). Manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and should have Green Guard Certification for few of its products.

Big size almirahof 916mm W x 486mm D x 1981mm H made of 0.7mm thick CRCA MS epoxy powder coated with welded construction. The almirah should have 4 adjustable shalves made with 0.8mm thick CRCA MS. The doors should be metal door made with0.8mm thick CRCA MS having mozac handles with m10 screw type lever.The other components should be made from 0.9mm thick CRCA MS. The locking mechanism should be 3 way locking mechanism with shooting bolt.The shelves should be height wise shelf mounting. The finish of the almirah should be epoxy powder coated to the thickness of 50 microns.The minimum clear height between two adjacent shelves should be 355 mm. Manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and should have Green Guard Certification for few of its products.

Reading Table: Overall Size: : 1800mm W x 900mm D x 750mm H made of 25 mm Thick PLB Tops with 2mm Thick PVC Edge Beading, the table should have four legged understructure made of Dia. 38.1 x 1.6 mm thick M.S ERW tube. and 1.6 mm thick M.S Cframe Supporting the Top. Manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and should have Green Guard Certification for few of its products.

The table top thickness and drawer front thickness should be 15mm Medium density fibre .The thickness should be 14mm MDF for inner drawer left & right.The thickness should be 3mm for drawer bottom,15mm PB for other panels,0.18mm PVC vacuum laminating for surface of table top and drawer front, 0.4mm lipping forother panels. The Load bearing capacity of the table top should be :35 Kg.The Construction of the table should be Knock down fitting. The Color should be Granite black.Overall Dimension :Length 1000 mm,Width 480 mm,Height 720 mm. Manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and should have Green Guard Certification for few of its products.

The seat is made up of 1.2±0.1cm thick hot pressed plywood and upholstered with fabric or synthetic leather and moulded Polyurethane foam.the back is made up 1.2±0.1cm thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and mouldedp polyurethane foam.The back ply and foam is designed with contoured lumber support for comfortable seating posture.Back size:48cm(W) x 76 cm(H),seat size : 51cm(W) x 48cm(D).The high resilience polyurethane foam for seat and back is moulded with density 45±2kg/m³ and hardness load16±2 kgf as per IS:7888 for 25% compression.The armrest top is made of moulded polyurethane and mounted on to a drop lift height adjustable type M.S. Tubular armrest support chrome plated.The armrest height is adjustable upto 6.5±0.5cm. In 5 steps & also has swivel adjustment of 22°±2° on both sides.The mechanism is knee-tilt synchro mechanism with following features:360° revolving type,single point control,front pivot for tilt with feet resting on ground ensuring more comfort,tilt tension adjustment,4 position locking with anti-shock feature,seat/back tilting ratio of 1:2 and seat depth adjustment of 6.0±0.5cm can be locked in 6 positions.The backrest consists of a sliding up down mechanism,which can be adjusted in the range of 7.5±0.5cm and can be locked in 4 positions for correct position of lumber support.The pneumatic height adjustment has an adjustment of 9.0±0.3cm.The pedestal is fabricated from 0.2±0.02cm thick high resilience sheet(IS:DD 1079/HR skin pass),chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. Twin wheel castors.The pedestal is 66.0±0.05cm.Pitch center dia (76.0±1.0cm with castors).The twin wheel castors are injection moulded in black nylon. Manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and should have Green Guard Certification for few of its products.

Dimension: 1500 mm W x 750 mm D x750 mm H . Worktop:18mm thk. Pre Laminated Particle Board (PLB) All work surface edges are duly sealed with 2mm thick PVC Edgebanding. Modesty panel:18mm thk. Pre Laminated Particle Board (PLB) All work surface edges are duly sealed with 2mm thick PVC Edgebanding. Rectangular Frame: Fabricated component in 1.2mm thick CRCA (IS:513), Finish: Powder coat (Epoxy polyester.Plastic Cap for Cable travel: Injection Moulded Polypropylene. Darwer: Shell and Drawer tray :0.6mm thick CRCA (IS:513) , Finish: Powder coat (Epoxy polyester)

The seat assembly is circular type dia of 30.0 cm and made of 20BG thick CR Steel. It is welded to the understructure and black powder coated. The understructure is made of M S Tube dia 2.2 cm (7/8”) x 18BG thick MS E.R.W Tube. Its is welded to the MS Fabricated circular seat assembly and black powder coated . The understructure is provided with black PP injection moulded ferrules. Width : 47.3cm ; Depth : 47.3cm;Seating height : 46.5cm

The top should be  made from 25mm Thick Pre–laminated board with 2mm thick. PVC edge beading.The Side Panels should be made from 25mm Thick Pre–laminated Twinwith 2mm thick PVC Lipping of same color on sides  and0.8mm PVC Lipping of matching color on the bottom curve.Modesty panels shouldbe made from 18mm thick Pre­Laminated BoardWith 0.8mm PVC Lipping of matching color.These panels are made from 25mm thick Pre­Laminated Twin with 2mm PVC  Lipping of Matching Color on sides and  0.8mm PVC Lipping of matching color on the bottom curve.Overall dimension of the table : 2100W * 1200D * 750H

The seat and back should be made up of seasoned wood and plywood uholstered with black synthetic leather and polyurethane foam.The back and seat size should be 46cm x 27cm and 46 cm x 40 cm respectively.The armrest tube should be made up of Ø 2.54 ± 0.03 cm x 0.2 ± 0.016 cm thick M.S. E.R.W tube and powder caoted. Armrest should be gas assisted injection moulded from black polypropylene. The understructure assembly should be cantilever type frame made of Ø 2.54 ± 0.03 cm x 0.2 ± 0.016 cm thick M.S. E.R.W tube and powder coated.

– 6000x1500x900MM C-FRAME SYSTEM All C-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994. The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps should give maximum flexibility and modularity while making a layout. C-frame should be constructed from a rectangular pipe with a cross section of 60mm x 30mm and should be 2 mm thick and should be without a vertical front leg to give a clean look. This should provide more knee space or leg space. The C-frame legs should be supplied with adjustable feet (tolerance from -5mm to +20mm) to correct the unevenness of flooring. The tubular enclosed type construction should discourage dust accumulation and unwanted development of bacteria & fungus. Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. The structure should have a removable back panel to provide access for maintenance throughout the length of table. The C-frame should also have skirting at back bottom side. It should be of heights 900mm, depths1540mm. All frame-work is should be pre-treated with superior pure epoxy powder coated finish. HORIZONTAL MEMBERS These should be made from rectangular pipes of 2mm thickness. Cross-sectional dimensions of the pipe should be 60 x 30 x 2 mm. They should be made of CRCA MS and coated with pure epoxy powder. These connect two C-Frames together as shown using C-clamps/U-clamps. Together with the C-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. REAGENT SHELVES Fixed-Type reagent shelves should be provided. It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets.2 Nos ofSize 1500x300mm double sided with cutout for 6 module plates to be provided. WELDED UNDER-BENCH STORAGE CABINETS Welded cabinet body should be of flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should be of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Shelf should be eight bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front is of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Dimensions: W=450/600mm, D = 530mm, H = 635/485mm. Configurations: 2 Shutters + 1 Drawer, MOC: MSCRCA: IS – 513 (1994), Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel should be of 0.8mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel should be of 0.8mmthk. Finish: Powder coating pure epoxy, thickness 60-70 microns. Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm. Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit). Shutter should have provision of roller catch. 6 Nos to be provided. SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade including water faucets and gas valves LABORATORY SINK AND ACCESSORIES Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Standard bowl size (L x W x D) is 500 x 400 x 300 mm. Faucetshould be 1-way/3-way type faucet . 3 Nos to be provided. WORKTOP It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. Size of the worktop is 6000x1500mm.

Overall Dimensions: L x D x H: 1500 x 800 x 850- mm. (including TOP). Load bearing capacity: 1000 kg UDL. Complete with under structure frame, Multiplex top, 1 normal extension drawer & 1 connection bottom bar. Under structure Frame : Work bench under structure has H/C profile & made of prime quality HR/CR steel. The legs of the vertical frame is “C” shaped channel type with width of 80 mm. The Top of the leg has “Y” shaped runner crown to ensure wide support & to withstand shock load. dead load, & steady load. Multiplex Top: The multiplex worktop includes various layers of beech wood which are planed, glued, & pressed together. This makes the worktop non-deformable, load & wear resistant. The thickness of the top is 50 mm. Drawer: Overall dimension of the drawer is 565 x 725 x 255 (H)- mm. Load bearing capacity of the drawer is 60 kg. Connecting bottom bar: Connecting piece rests on frame bars to connect two frames at bottom. Pre treatment and surface finish: The raw material used in production of the unit provided is virgin steel.The same undergoes 7 steps anti rust and anti corrosion treatment with special hot oil treatment to safeguard against saline and humid conditions.The final product is Galvanized or powder coated to an average of 60 - 80 micron thickness with Epoxy Polyester blend and meet the following criteria.

Dimension: 1500W x 895 D x 750 H . Panel: The Desk panel, Seat Panel and Back are made from 18 mm thick Pre­ Laminated Boards with PVC edge banding on all sides. Understructure: The Understructure is made of 25.4 x 25.4 x 1.6 mm thick powder coated Electric Resistance Welding (ERW) tubes at base which are welded to the desk and seat supports that are made of 1.0 mm thick powder coated MS ‘C’ sections. Stiffeners that are provided between the 2 vertical frames at base and back of seat are made from 25.4 x 25.4 x 1.6 mm thick powder coated ERW tubes. The tubes are closed with plastic caps. Additional horizontal supports of 1.5 mm thick powder coated MS ‘C’ sections are placed below the desk and seat to add to the rigidity of the structure. Storage Shelf: The storage shelf is made from 0.8 mm thick powder coated MS sheet which is affixed below the desktop. Level adjustors are provided to take care of unevenness in floor. Manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and should have Green Guard Certification for few of its products.

ISO 9001:2008, ISO 14001:2004, ISO 18001:2007, BFIMA& Green Guard certified bed made of mild steel duly powder quoted. The square legs are made of 38.1mm x 1.2 mm thk MS tube having end cap. 2 square tubes of 25mm x 1 mm to be provided in the head board & leg board side. Top will be MS Perforated 1.2 mm thick. Underneath of the sheet there will be 4 supporting bars made of 50.8x25.4x1.2 mm thk MS Tube. The main structure frame will be made of 50.8x25.4x1.2 mm thk MS tube. A 100x100x3.2 mm thick support bracket welded with tube & bolted with bed frame with M8 Bolt. Overall size of bed 1980mm (L ) x 915mm (W)x 650mm (H) & bed stead height 400 mm. CO2 welding finish is required & no welding on the top edge. Good quality 12mm plywood should also be provided. Manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and should have Green Guard Certification for few of its products.

All Steel Book Rack Single Sided : Overall Size: 1890 mm H x 900mm W x 316 mm D: Construction and the material shpould be rigid knock down mechanism, panel are made up of CRCA 0.6 mm thickness and front frame should be made up of CRCA .8 mm thick. and should be 5 nos of rack ( 6 loading level). Each shelevs should have load bearing capacity of 40 kg UDL. Finishes: Epoxy Powder coated upto 50 micron. Manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and should have Green Guard Certification for few of its products.

C-FRAME SYSTEM 6000mm(W) x 1500mm(D)x 900mm(H).-Table 1 .All C-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994. The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps should give maximum flexibility and modularity while making a layout. C-frame should be constructed from a rectangular pipe with a cross section of 60mm x 30mm and should be 2 mm thick and should be without a vertical front leg to give a clean look. This should provide more knee space or leg space. The C-frame legs should be supplied with adjustable feet (tolerance from -5mm to +20mm) to correct the unevenness of flooring. The tubular enclosed type construction should discourage dust accumulation and unwanted development of bacteria & fungus.Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. The structure should have a removable back panel to provide access for maintenance throughout the length of table. The C-frame should also have skirting at back bottom side. It should be of heights 900mm, depths1540mm. All frame-work is should be pre-treated with superior pure epoxy powder coated finish. HORIZONTAL MEMBERS These should be made from rectangular pipes of 2mm thickness. Cross-sectional dimensions of the pipe should be 60 x 30 x 2 mm. They should be made of CRCA MS and coated with pure epoxy powder. These connect two C-Frames together as shown using C-clamps/U-clamps. Together with the C-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. WELDED UNDER-BENCH STORAGE CABINETS Welded cabinet body should be of flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should be of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Shelf should be eight bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front is of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Dimensions: W=450/600mm, D = 530mm, H = 635/485mm. Configurations: 2 Shutters + 1 Drawer, MOC: MSCRCA: IS – 513 (1994), Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel should be of 0.8mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel should be of 0.8mmthk. Finish: Powder coating pure epoxy, thickness 60-70 microns. Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm. Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit). Shutter should have provision of roller catch. 6 Nos to be provided. ELECTRICAL TRUNKING Used for housing electrical switches and sockets, data and voice points, its top panel, bottom panel of the trunking should be made from 0.8mm thick CRCA MS panel. It should be available in both, single sided and double sided configurations. It should be made from CRCA MS with pure epoxy powder coating. The front surface that houses the electrical points should have a slope. 2 Nos of Size 1500x260mm double sided with cutout for 6 module plates to be provided. WORKTOP It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. Size of the worktop is 6000x1500mm C-FRAME SYSTEM - 4500mm(W)X1500mm(D)X900mm(H). ( Table 2) All C-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994. The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps should give maximum flexibility and modularity while making a layout. C-frame should be constructed from a rectangular pipe with a cross section of 60mm x 30mm and should be 2 mm thick and should be without a vertical front leg to give a clean look. This should provide more knee space or leg space. The C-frame legs should be supplied with adjustable feet (tolerance from -5mm to +20mm) to correct the unevenness of flooring. The tubular enclosed type construction should discourage dust accumulation and unwanted development of bacteria & fungus. Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. The structure should have a removable back panel to provide access for maintenance throughout the length of table. The C-frame should also have skirting at back bottom side. It should be of heights 900mm, depths1540mm. All frame-work is should be pre-treated with superior pure epoxy powder coated finish. HORIZONTAL MEMBERS These should be made from rectangular pipes of 2mm thickness. Cross-sectional dimensions of the pipe should be 60 x 30 x 2 mm. They should be made of CRCA MS and coated with pure epoxy powder. These connect two C-Frames together as shown using C-clamps/U-clamps. Together with the C-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. WELDED UNDER-BENCH STORAGE CABINETS Welded cabinet body should be of flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should be of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Shelf should be eight bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front is of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Dimensions: W=450/600mm, D = 530mm, H = 635/485mm. Configurations: 2 Shutters + 1 Drawer, MOC: MSCRCA: IS – 513 (1994), Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel should be of 0.8mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel should be of 0.8mmthk. Finish: Powder coating pure epoxy, thickness 60-70 microns. Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm. Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit). Shutter should have provision of roller catch. 6 Nos to be provided. ELECTRICAL TRUNKING Used for housing electrical switches and sockets, data and voice points, its top panel, bottom panel of the trunking should be made from 0.8mm thick CRCA MS panel. It should be available in both, single sided and double sided configurations. It should be made from CRCA MS with pure epoxy powder coating. The front surface that houses the electrical points should have a slope. 2 Nos of Size 1500x260mm double sided with cutout for 6 module plates to be provided. WORKTOP It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. Size of the worktop is 4500x1500mm

The seat and back should be made from seasoned wood ,knitted with cane and finished with synthetic paint (black). Back size : 45.7cm (W) x 39.0cm (H).Seat size :45.7cm (W0 x 42.4cm (D).Cane is produced from blends of high and low density polyethylene. The cane high tensile strength at break =1400 kg/cm2 (min) & Elongation at break =54% maximum.The seat and back should be made of cane.The armrest tube should be made of dia 2.54 +/- 0.03 cm x 0.2 +/-0.2 +/-0.016cm thk MS ERW tube and power coated (DFT 40-60 microns).The armrest should be gas assisted injection moulded from black polypropylene.The understructure assembly should be a cantilever type frame made of dia 2.54 +/-0.03cm x 0.2 +/-0.016cm thk MS ERW tube and powder coated (DFT 40-60 microns). Manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and should have Green Guard Certification for few of its products.

The seat and back should be made of 0.12+/-0.0096 cm thk CR steelperforated sheets which are welded to a seat/back assembly. The armrest should be made of oblong tube of size 0.35+/-0.024cm x0.15 +/-0.015cm x0.16 +/-0.015cm thk and dia 0.15+/-0.02 cm bright bar weldedtp seat & back frame assembly.Overall seat size:39cm(W) x 41.5cm(D) and back size :39cm (W) x 21.5 cm (H) . Manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and should have Green Guard Certification for few of its products.

The top of the table should be made from 18mm thk pre laminated board.The Dimensions of the table should be : 830mm (W) x 630mm (D).The Understructure should be made from MS SQ tubes of 25mm x 1.6 cm thk.The table top should be inclined , such that height from the ground should be 870 mm from one side and 1000mm from the another.There should be storage shelf , made from 18mm thk pre laminated board at a height 650mm from the ground.There should be provision of hook .

12 x 5 ft

Chair should have pneumatic seat height adjustment facility. Height of the chair should be atleast 97cm. Depth and width of the chair should be at least 76cm. Seat height should be at least 54cm.Back size-47.5cmWx58cmH. The seat and back should be made up of 1.2±0.1 cm thick hot pressed plywood upholstered with fabric upholstery cover and moulded polyurethane foam .The back Foam should be designed with countered lumbar support for extra comfort. The High resilience polyurethane Foam should be moulded with density=45±2kg/m3 and hardness load 16±2 kgf. The armrest should be injection moulded from black Co polymer polprylene. It should have centre tilt mechanism with tilt tension adjustment, upright position locking, 360 degree revolving and seat back tilting ratio should be 1:3.The pedestal should be injection moulded in black 33% glass filled Nylon-66. The pedestal should also have 5 nos twin wheel castor..The seat end of the chair towards the legs should have a appearance as of waterfall edge. Manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and should have Green Guard Certification for few of its products.

It should have a rigid knock down construction made of prime quality CRCA steels with panel thickness of 0.6mm while front frame and shelf thickness of 0.8 mm. It should have full height steel hinged door with plastic reccesed handle cum cam lock. The lock should have 3 way locking mechanism with shooting bolt arrangment. The almirah should have 4 nos of height adjustable shelves with a uniformly distributed load capacity of 80 kg.Epoxy powder coated finish of thickness 50 microns (+/-10 ).Dimension: 1168 mmHx900mmWx450mmD. Manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and should have Green Guard Certification for few of its products.

Dimensions: 600mm(W) X 450mm(D) X 750mm(H). Top should be made of 18mm melamine face chipboard, others 15mm chipboard laminated with decorative paper .The Castor size should be 40mm x 45mm with 2 lockable and 2 unlockable.The construction should be knock down construction.It should be provided with KBPT. Manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and should have Green Guard Certification for few of its products.

Dining Table: Overall Size: : 1665mm W x 900mm D x 750mm H made of 25 mm Thick PLB Tops with 2mm Thick PVC Edge Beading, the table should have four legged understructure made of Dia. 38.1 x 1.6 mm thick M.S ERW tube. and 1.6 mm thick M.S Cframe Supporting the Top. Manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and should have Green Guard Certification for few of its products.

8 x 4 ft