Tourism Department Tender

Filling with Gravel in trenches, sides of foundations and basement with initial lead in layers not exceeding 15 cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T & P etc., complete for finished item of work. (APSS NO. 309 & 310)

Supply, Laying and Fixing of precast concrete blocks for paving of M-40 grade and thickness not less than 80 mm for Medium traffic areas conforming to IS 15658:2006 in all shapes and designs as per the manufacturer's specification set over a base coat of 50mm thk sand bed including cost and conveyance of all materials like sand, water tiles etc.,to site, labour charges for loading & unloading, laying to desired lines and levels complete and Overheads & Contractor Profit etc. for finished item of work.

Construction of cement concrete kerb with channel with top and bottom width 115 and 165 mm respectively, 250 mm high in M 20 grade PCC on M10 grade foundation 150 mm thick, kerb channel 300 mm wide, 50 mm thick in PCCM20 grade, sloped towards the kerb, kerb stone with channel laid with kerb laying machine, foundation concrete laid manually, all complete as per clause 408 MORTH

Flooring with Lapothra finish Shahabad/ Tandur stone slabs of 20 to 25 mm thick size 600x600mmset over a base coat of CM (1:8) prop. 20mm thick over CC bed already laid or RCC roof slab , including neat cement slurry of honey like consistancy spread @ 3.3 kgs per Sqm. and jointed neately with white cement paste mixed with pigment of matching shade to match the shade of granite to full depth including cost and conveyance of all materials like cement, sand, water, granite, white cement etc., to site (excluding cost of C.C. bed), cost of base coat and all labour charges for mixing of cement mortar, laying granite to required slope as directed by the Engineer- in-charge, cost of overheads & contractors profit etc., complete for finished item of work . (APSS No.701 & 707)

Plain Cement concrete Grade M10 - Nominal Mix using 20mm metal, machine crushed granite from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, sales & other taxes on all materials and including all charges for machine mixing, laying concrete in foundations and under flooring bed, ramming in 15 cm layers finishing top surface to the required level curing etc.,and overheads & contractors profit complete for finished item of work.

A. DISMANTLING Roof Mangalore tiles clearing away and carefully stacking materials useful for reuse.

Providing impervious coat to exposed RCC roof slab surface with CM(1:3), 20mm thick with 1kg of water proof compound per bag of cement laid over roof when it is green including cost of all materials, seigniorage charges, excluding conveyance charges of materials and including all operational, incidental and labour charges for mixing mortar, laying, rendering smooth and thread lining, curing, rounding off junctions of wall and slab etc,, complete for finished item of work.

Painting to External wall faces with one coat of water based cement primer of exterior grade and two coats of acrylic emulsion paint with silicon additives having VOC (Volatile Organic Compound) content less than 50 grams/litre [total 3 coats] including cost and conveyance of all materials to site, sales & other taxes, incidental, operational and all labour charges etc complete for finished item of work in all floors.

Supply, Transportation, Installation, Testing and Commissioning of 160 KVA Transformer with all test reports. The Transformer shall be designed and manufactured as per Energy Efficiency Level - 2 at basic Insulation level conforming to ISS 2026 (Part- I to Part - II) with latest ammended,and as per IS 1180 Part-I : 2014 latest ammended, OCTC with initial filling of oil as per IS 335-1993. The basic details of the Transformer are as under. 1. Quantity : 1 2. Rated KVA : 500 KVA 3. Service & Location: Continuous Outdoor Distribution Transformer 4. Mounting : Plinth. 5. Wound : Copper Double wound 6. Type : Core type oil immersed 7. Cooling : ONAN 8. Temp Rise : 40⁰C in oil, 45⁰C by resistance 9. Vector Group: Dyn 11 10. Primary Connection : Delta 11. Nominal Voltage / Current : _ 12. Highest system Voltage: 12000V 13. Primary Frequency :50 HZ +/- 3% 14. Number of Phases : 3 15. Primary wires: 3 16. Secondary connection : Star 17. Secondary Volts / Current : 433V 18. Secondary phases : 3 19. Secondary wires: 4 20. Taps on primary winding for primary voltage variation : +5% to - 10% in steps of 2.5% of 7 position (6 Steps) 21. Terminal arrangement. a.HV: HT terminal box as per the sitecondition. b. LV: Cable box suitable to receive ------------Sq.mm XLPE cable 22. LV:One separate terminal for earthing. 23. Total Losses at 50% Loading [Watts] [Max] --- as per IS 24. Total Losses at 100% Loading [Watts] [Max]--- as per IS 25.Percentage Impedance at 75 deg. C at -----as per IS 26. No Load current: Less than 2% of full load current. 27. Standard Fittings & Accessories. a. Rating and terminal marking plate: One b. Lifting Lugs: Two c. Off-circuit tap switch :One d. Earthing Terminals :Two e. Radiators (Attachable): Adequate f. Explosion vent with Diaphragm :One g. Conservator with Drain plug: one h. Oil filling hole with cap :One i. Oil level indicator : One j. Dehydrating Silica gel Breather : One k. Terminal Arrangement: HV With TerminalBox l. Terminal Arrangement : LV Cable Box m. Separate Neutral Bushing : One n. Drain cum filter valve with blanking plate: One o. Air release device : One p. Thermometer Pocket : One q. Four :Unidirectional flat rollers r. One :10Cm dial thermometer (Rigid stemtype)

Supply Installation Testing And commissioning of 160 kVA at 0.8 pf 415V 50Hz 3-Ø DG Set complete with 1500 RPM Diesel Engine of suitable BHP & AC Brush less SPDP Alternator mounted on a common base Frame & coupled through a flexible coupling or close coupled. Alternator: It shall be self regulated, self excited and confirms to IS: 13364/1992 or latest version with regulation of +5% from No load to full load, IP23, with standard Alternator Protection ( Over voltage, over speed & under voltage). Diesel Engine: Itshall have residential silencer, up to 10 M exhaust piping , electronic / Mechanical governor, Manual & electric Start, Batteries, Fuel tank & piping, control panel (16 G) with SPN (For 5 KVA)/TPN MCCB of required rating (25/36/50 KA) with PLC based Engine controller supplied by OEM, Ammeter, Voltmeter, Frequency Meter or Multi function meter, Energy Meter & Hour Meter, Engine instruments panel,AVM and Automatic Voltage Regulator. The diesel engine shall be capable of providing 10% over load for 1 Hr for every 11 Hrs of continuious running at full load. The DG set shall be supplied with initial filling of fuel,lube oil, coolant oil as per OEM specifications and shall be tested at site. Accoustic Enclosure: Weatherproof, powder coated Accoustic enclosure for DG set for sound attenuation fabricated from 1.6 mm CRCA sheet steel (structure) with side wall fabricated from 1.6 mm CRCA sheet and filled with foam as per CPCB norms latest amendments & IS 8183 .The doors are fabricated from 1.6 mm CRCA sheet packed with accoustic material, floor of MS chequrred plate 5.0 mmthick, All doors/ opening are sealed with neoprene/ EPDN gaskets. The DG Set shall be maintained for two years after commissioning by the supplier including regular servicing, cost of consumables etc complete as specified by the OEM along with warranty for two years. The enclosure has built in fuel tank, residential silencer (isolated from main DG chamber) with protection and tripping of DG set against temperature of more than 50 °C. All controls for operation of DG set are from outside the enclosure with DG control panel having processor based genset monitoring and control system MCCB/ACB Ammeter, voltmeter, Pf meter, frequency meter, KWH meter, Ind. Lamps etc. mounted inside enclosure , visible and accessible from outside. The enclosure should be suitable for following capacity DG sets and alternator.Noise level is less than 75 db (A) at a distance of 1 Mtrs as per CPCB-II norms,complete in all respect of following capacity :

Bed preparation for Korean/Mexican: Dressing the surface to the desired shape, laying of 150 mm. (6”) thick fine red garden soil, covered with a thin layer of 10 mm thick sand, watering, rolling (compacting to 4" thickness by hand roller), including the cost of red garden soil, sand and labour charges etc., for complete bed preparation and laying and ramming of lawn mats / rolls in proper position on existing prepared bed by internal transportation from dumped place, including cost of labour for laying, ramming by hand roller / demesha, internal transportation and watering etc., complete for finished item of work excluding cost of grass, fertilizers and chemicals etc., for 1 Sqm (Red garden soil in this context it is defined as sandy loamy garden soil congenial for plant growth which shall be of light textured, crystalline, porous and friable, fertile, slightly acidic or neutral)