Marine Products Export Development Authority Tender

Its size shall be 1650 Width x 700 Depth x 743 Height (Main Desk) 1000 Width X 450Depth X 743 Height (ERU).Top shall be of 18 mm thickness made of PLT board with 2 mm Edge banding. Wenge and savannah Maple PLT board shall be used. The Understructure shall be in pre-laminated panels made with PLT boards . 2- Drawerand 3 - Drawer storage units with different combinations to support tops made with 18 mm PLT boards of different colours.Modesty and back panels made with 18 mm PLT boards. The pedestals / storages shall be fitted with necessary locks.

Overall size shall be 3000 X 1150 X 740.Work top-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade, Edge banded with matching 2 mm thick PVC lipping. Access panels provided with soft closing hinges Understructure-The Under-structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for improving the aesthetics. The product has a knock-down construction. Wire Raiser-A wire raiser made of 0.8mm CRCA MS. It is epoxy polyester powder coated (DFT 40-60 microns) for flow of wires and cables. Cutout provision below Access flap at two locations for standard 8 module Anchor Roma is provided. Beside each cutout, an additional cutout with plate is provided for mounting Audio Visual Cables

Overall size shall be DIA-900 X 700 WORKTOP (PU) Worktop is made of 25mm MDF OSR with pu matt finish on top side. Hardness on top surface is 2H. The worktop is available in 5 shapes; viz.: Circle, Bite, Rectangle, Square & Face UNDER-STRUCTURE: The under-structure consists of an InnerTube Assembly with Top Plate, for Worktop Mounting, & an Outer Tube Assembly with Round/Rectangle/Square Bottom Plate. The Inner & Outer Tube Assemblies are telescopically connected. The Top Plate is made of 5mm thk HOT ROLLED Steel Plates (HR) & the bottom plate is made of 8mm thk HOT ROLLED Steel Plates (HR) . The Inner Tube Assembly is made of 082.5 x 2thk ROUND ELECTRIC RESISTANCE WELDED Tubes (ERW) and 8mm thk HOT ROLLED Steel Plates (HR) welded together using TUNGSTEN INERT GAS Welding. The Outer Tube Assembly is made of 089 x 2.5 thk and ROUND ELECTRIC RESISTANCE WELDED Tubes (ERW) and 8mm thk HOT ROLLED Steel Plates (HR) welded together using TUNGSTEN INERT GAS Welding. The whole structure is EPDXY POLYESTER Powder Coated (DFT 40-60 microns). The product has a knock-down construction. It is assembled using alloy steel hardware (blackened & coated with rust preventive oil).

SEAT FOAM : The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. BACK FOAM : The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. LEG ASSEMBLY : It should be welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. Width (W): 146.0 CM. Depth (D): 90.5 CM. Height (H): 85.5 CM. Seat Height (SH): 45.0 CM.

The Seat and Back should be made up of injection moulded indoor grade PolyPropylene compound SEAT SIZE : 52.5 cm. (W) x 53.2 cm. (D) BACK SIZE : 51.6 cm. (W) x 40.5 cm. (H) The powder coated ( DFT 50±10 microns ) welded tubular frame should be made from 0 2.22 ± 0.03 cm x 0.16 ± 0.0128 cm and 3.5 ± 0.03 cm x 1.5 ± 0.03 cm x 0.16 ± 0.0128 cm MSERW tube. The shoes should be made of indoor grade PolyPropylene compound and snap fitted with tubular frame. Overall Dimensions of Chair Seat Height - 45.0 cm. Height - 84.5cm. Width-52.5 cm and Depth-55.8 cm.

SEAT/BACK ASSEMBLY: The seat is made up of 1.5 ±0.1cm. thick hot-pressedplywood and upholstered with fabric upholstery covers and moulded Polyurethane foam.The seat has extra thick foam on front edge to give comfort to popliteal area. The Back is injection moulded in glass filled Polypropylene which is upholstered with Mesh fabric.The back consist of adjustable lumbar support made of injection mouldedPolypropylene having an adjustment of 5.0 ±0.1 cm. The chair seat & back size are *SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D)*MESH BACK SIZE 51.0 cm. (W) x 70.0 cm. (H) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45±2 kg/m³ and hardness 16±2 kgf for 25% compression. ARMRESTS :The adjustable armrest should designed with the following features :· Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon· Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism should designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment HEADREST: The Headrest sub-assembly is made up of injection moulded glass filledPolypropylene which is upholstered with moulded HR polyurethane foam and fabric. Ithas an adjustment of 4.0 ± 0.1cm & it is assembled over Thrill mesh back chair.The complete headrest assembly is retro fit to the main chair. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment with anadjustment stroke of 9.5 ± 0.3cm. PEDESTAL ASSEMBLY : The pedestal is injection moulded in glass-filled Nylon andfitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia.(76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 117.0 - 130.0 CM. SEAT HEIGHT (SH): 44.5 - 54.0 CM.

Seat Assembly: The Cushioned seat is made of Injection molded Plastic outer & inner. Plastic Inner is upholstered with leatherette and moulded High Resilience (HR) Polyurethane foam of Density 45+/-2 kg/m3, and hardness load 16 +/- 2 kgf for 25% compression Seat Size: 47.0 cm. (W) * 48.0 cm. (D) Back Assembly: The Cushioned back is made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9+/-0.03cm. * 0.16 +/- 0.0128cm. It is upholstered with Leatherette. High Back Size: 47.7 cm (W) * 76.4 cm. (D) Mid Back Size: 47.7 cm (W) * 60.1 cm. (D)

SEAT/BACK ASSEMBLY: The seat and back are made up of 1.2 ±0.1cm. thick hot-pressedplywood measured upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contouredlumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort topopliteal area. MID BACK SIZE 47.5 cm. (W) x 58.0 cm. (H). SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded withdensity = 45±2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS :The one-piece armrests are injection moulded from black Co-polymer Polypropylene. TUBULAR FRAME : The powder coated ( DFT 40-60 microns ) tubular frame iscantilever type & made of Ø 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. Overall Dimensions of Chair WIDTH (W): 61.4 CM. DEPTH (D): 64.5 CM. HEIGHT (H): 89.5 CM. SEAT HEIGHT (SH): 46.5 CM.

SEAT ASSEMBLY: The seat is made up of 1.5±0.1 cm thick hot-pressed plywood upholstered with fabric and moulded polyurethane foam. SEAT SIZE: 51.8cm (W) x 49.7cm (D) BACK ASSEMBLY: The Back is injection moulded in glass filled Polypropylene which is 2 upholstered with Mesh fabric. The back consist of adjustable Lumbar support made of injection moulded Polypropylene having an adjustment of 5.0 10.1 cm. BACK SIZE: 47.9 cm(W) x 66.9 cm (H) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45+/-2 kg/m and hardness 14 ± 2 kgf for 25% compression. ARMRESTS (ADJUSTABLE):The height adjustable armrest is made of Polypropylene and can be adjusted to 6.010.1cm height it also has swivel and To and Fro adjustment with moulded PU armtop ACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features 360° revolving type Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort Till tension adjustment can be operated in seating position 5 position Tilt limiter giving option of variable sit angle to the chair Seat/back tilting ratio of 1:2 The mechanism housing is made up of HPDC Aluminium & black powder coated (DFT 40 to 60 micron) HEADREST The Headrest sub-assembly is made up of injection moulded glass filed Polypropylene which is upholstered with moulded HR polyurethane loam and fabric has an adjustment of 3.00.1cm & it is assembled over GRETA 20F The complete headrest assembly is retro fic to the main chair PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment with an adjustment stroke of 10.0±0.3cm. PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is 166.1±0.5 cm.(76.1 ± 1.0 cm. with castors). TWIN WHEEL CASTORS: The twin wheel castors are Injection moulded in black Polyamide having 6.01 0.1cm wheel Diameter. WIDTH (W) - 76.0cm DEPTH (D) - 76.0cm HEIGHT (H) - 114.0 cm- 123.5cm SEAT HEIGHT - 43.5 - 54.0cm

SEAT/BACK A SSEMBLY: The seat is made up of 1.2 ± 0.1cm thk. hot pressed plywood measured..The Back is made up of injection mou1ded glass filled nylon & upholstered using Mesh fabric with high tenacity yarn. SEAT SIZE : 47.0 cm. (W) x 49.5 cm. (D) BACK SIZE : 45.0 cm. (W) x 65.3 cm. (H) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45+/-2 kg/m° and hardness 16 + 2 kgf for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features : • Up-Down adjustment— 8 steps (8 0+0.Scm range) • Height adjustable armrest structure which is Powder Coated & fitted with an armrest top. • Fixed Armrest Top is PU moulded over metal insert. LUMBAR SUPPORT ASSEMBLY: The Lumbar support consists of polypropylene pad with moulded polyurethane foam & covered with polyester fabric.The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pa6. Lumbar pad has an adjustment of 8.0 + 0.5 cm in height. FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features. • 360° revolving type. • Single point control. • Front-pivot for tilt with feet resting on ground ensuring more comfort. » Tilt tension adjustment. • 4-position locking with anti-shock feature. • Seat/back tilting ratio of 1:2. PNEUMATIC HEiGHT ADJUSTMENT. The pneumatic height adjustment has an adjustment stroke oi 10.0 + 0.3 cn°. Pedestal Assembly : the pedestal is injection moulded in black 30% glass filled nylon and fitted with 5 nos. twin wheel castors. H=The pedestal pitch center dia is 66.1+0.5 cm TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Nylon. NECKREST : The Neckrest assembly consist of polypropylene pad with moulded polyurethane foam & covered with polyester fabric Neckrest is fixed to Back Assembly through Neckrest connector Neckrest assembly has height adjustment of4.2 ± 0.5 cm and rotation adjustment of overall 76°+ 2°. The complete neckrest assembly is retro fit to the main chair

SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood , upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D). BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn. BACK SIZE : 46.5 cm (W) x 60.5 cm (H). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. CENTRE-TILT mechanism: The mechashould be m should be designed with the following features: • 360° revolving type. • 17° ±2° maximum tilt on pivot at centre • Upright position locking. • Tilt tension adjustment. . PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. TELESCOPIC BELLOW ASSY: The bellow should be 3 piece telescopic type and injection moulded in Black Polypropylene. PEDESTAL ASSEMBLY: The pedestal should be injection moulded in black 33% glass-filled Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors.) TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black nylon. Overall Dimensions of Chair Seat Height - min 43.3 to max 54.3cm. Height - min 89.5 to max 100.5cm. Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.

SEAT FOAM : The seat should be made with PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. BACK FOAM : The back should be made with PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. LEG ASSEMBLY : It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. Width (W): 206.0 CM. Depth (D): 90.5 CM. Height (H): 85.5 CM. Seat Height (SH): 45.0 CM.

CENTER TABLE TOP GLASS: It is 10 mm thick tempered clear glass with dimensions 1000 x 650 mm. CENTER TABLE BOTTOM GLASS : It is 6 mm thick tempered clear+frosty glass with dimensions 755 x 195 mm. TABLE LEGS: It is of 255mm thick Pre-laminated twin board of E1-P2 grade with PU walnut coating of size 70 x 70 mm.

Overall size shall be 4200 X 1500 X 740.Work top-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade, Edge banded with matching 2 mm thick PVC lipping. Access panels provided with soft closing hinges. Understructure-The Under-structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade, Edge banded withmatching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is addedat bottom edges for improving the aesthetics. The product has a knock-down construction. Wire Management-Bottom cabinet with door is provided for flow of wires and cables. Cutout provision below Access flap at four locations for standard 8 module Anchor Roma is provided. Beside eachcutout, an additional cutout with plate is provided for mounting Audio Visual Cables (eg.HDMI,VGA-A,etc).

Overall Size:Width : 88.1cm Depth : 54.8cm Height : 191cm Material:3 Body panels are made of 18 mm thick Prelaminated Particle Board 1S:12823 Class E1. All the exposed edges are edge banded with 0.8 mm thick PVC edge banding glued with Hot Melt EVA glue . Door are made of 18 mm thick Prelaminated Particle board IS:12823 Class E1 with all the exposed edges are edge banded with 0.8 mm thick PVC edge band glued with Hot Melt EVA glue.Drawer components are made of 18 mm thick Prelaminated Particle Board 1S:12823 Class E1. All the exposed edges are edge banded with 0.8 mm thick PVC edge banding glued with Hot Melt EVA glue.Body back and drawer bottom are made of 9 mm thick Prelaminated particle board IS: 12823 Class E1. Hardware:The high quality hardware used like Roller slides, Hinges , minifix, wooden dowels is of make Hettich.. Lock used for middle door is 3 way lock. Lock used for right hand door and drawer is cam lockConstruction :Knock Down construction. Packets : 4 packet.Finish :18 mm thick Prelaminated Particle Board 1S:12823 Class E1 is in Imperial Oak shade.Lipping shade is 299P MAKE REHAU

Overall Size :Depth — 461.0 mm Width — 460.0 mm Height — 510.0 mm Material:Body panels of Bed side table are made of 18 mm thick Prelaminated Particle Board 1S:12823 Class E1. All the exposed edges are edge banded with 0.8 mm thick PVC edge banding glued with Hot Melt EVA glue.Drawer front are made of 18 mm thick Prelaminated Particle board 1S:12823 Class E1. Hardware:The high quality hardware used like Roller slides, Hinges , minifix, dowels is of make Hettich.Construction:Knock Down construction. Packets :1 packet.Finish :.18 mm thick PrelaminatedParticle Board 1S:12823 Class E1 is in Imperial Oak shade.Lipping shade is 299P MAKE REHAU

Overall Size: Width- 970 mm Depth— 2046 mm Height -901 mm Material:Bed Structure conssst of metal frames made of M S. Channels in Imm Thickness.Horizontal plinths and bottom plinth are made of 25 mm Thick Prelaminated Particle Board 1S:12823 Class E1. Head board is made of 18 mm thick Prelaminated Particle board 1S:12823 Class E1 with all the exposed edges are edge banded with 0.8 mm thick PVC edge banding glued with Hot Melt EVA glue.Tailboard is made of 18 mm thick Prelaminated Particle board 1S:12823 Class E1. Side rail is made of 18 mm thick Prelaminated Particle board 1S:12823 Class E1. Mattress panels of Bed are made of 18 mm thick Prelaminated Particle Board IS: 12823 Class E1 with all the exposed edges are edge bandedwith 0.8 mm thick PVC edge banding glued with Hot Melt EVA glue.Hardware:The high quality hardware are used.Construction: Knock Down construction. Packets :2 packet.Finish :.18 mm thick Prelaminated Particle Board 1S:12823 Class E1 is in Imperial Oak shade. Lipping shade is 299P MAKE REHAU

Overall Size:Width - 1875 mm Depth — 2046 mm Height — 90.1 mm Material:3Bed Structure consist of metal frames made of M.S. Channels in 1.0mm Thickness. Horizontal plinths and bottom plinth are made of 25 mm Thick Prelaminated Particle Board 1S:12823 Class E1. Plinth support assembly is made of M.S. 25 mm square pipe in 1.2 mm thickness. Head board is made of 18 mm thick PrelaminatedParticle board IS:12823 Class E1 with 2mm edge banding glued with Hot Melt EVA glue. Tail board is made of 18 mm thick Prelaminated Particle board IS:12823 Class E1 with 0.8mm edge banding glued with Hot Melt EVA glue.Side rail is made of 18 mm thick Prelaminated Particle board 1S:12823 Class E1 with 0.8mm edge banding glued with Hot Melt EVA glue.Mattress panels of Bed are made of 18 mm thick Prelaminated Particle 1S:12823 Class E1 with 0.8mm edge banding glued with Hot Melt EVA glue. Hardware :The high quality hardware are used.Construction:Knock Down construction.Packets :2packet.Finish :.18 mm thick Prelaminated Particle Board 1S:12823 Class E1 is in Imperial Oak shade. Lipping shade is 299P MAKE REHAU

Its size shall be 1200 Width x 600 Depth x 743 Height.Top shall be of 18 mm thickness made of PLT board with 2 mm Edge banding. Wenge and savannah Maple PLT board shall be used. The Understructure shall be in pre-laminated panels made with PLT boards . Drawer storage units with different combinations to support tops made with 18 mm PLT boards of different colours.Modesty and back panels made with 18 mm PLT boards. The pedestals / storages shall be fitted with necessary locks.

Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and Edge banded with matching 2 mm thick PVC lipping. Access Flap along with a Gromett is provided on work surface for wire management Wire Management - Power box made with 0.8 mm thick CRCA , with switch plate (8+3 Module cut out provision for Anchor Roma) which is fixed with worktop along the width at Access Flap position. Modesty Panel & Side Skirting - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade, Edge banded with matching 2 mm thick PVC lipping. Understructure - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade, Edge banded with matching 2 mm thick PVC lipping TOP shelf - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade, Edge banded with matching 2 mm thick PVC lipping. Hinge Door + Drawer unit - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and Edge banded with matching 2 mm thick PVC lipping. **Drawer bottom is made of 5.5thk MDF whiteboard Handle is provided for ease of opening. HDU and Drawer is provided with cam lock for security. Essential Accessories - Wire Riser made of 0.8mm CRCA is provided for proper wire management. Organizer Plate made of 1.2mm CRCA is provided for magnetic sticky notes. Bag Hanger Hook made of 1.2mm CRCA is provided for bag hanging. Length - 2400mm Depth - 1770,870mm Height - 1080mm

Workstations - 1500W1 x 1500W2 x 600D Providing and placing panel based modular workstation in cluster of 4 workstations format, with partition thickness as 52.4 mm thk and ht - 1200 including powder coated aluminium trims. FIN: out of 22.5 mm thk panel formed out of blocks which are 18 mm thk PLB boards. Top block finished in fabric. Bottom block is finished in metal. HALF SCREEN (if applicable): out of 22.5 mm thk screen formed out of blocks which are 18 mm thk PLB boards. Screen finished in fabric tackable. Tiles: Combination of top tiles are fabric tackable and white board. Bottom tiles - Plain metal. Wire Management - Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. legs - metal powder coated legs at the shared condition. System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500W1 x 1500W2 x600D. The workstation should also include 3-drawer mobile storage unit, Keyboard tray, CPU trolley, Cable duct. Note: All partitions and side panels have levelling screws for adjustment in case of Uneven floor to take care of +/- 10-15 mm of uneven flooring.