Indian Institute Of Information Technology Tender

Supply and laying of incoming cable of suitable design required capacity and size for power supply to the flag mast pole feeder pillar from the Academic building through existing cable trench for a distance of 20m and through open trench upto the flag mast pole, including cost of all material, excavation, refilling, route markers, caution tape etc., supervisions charges complete as per theapproval and instruction of Engineer-in-charge.

Supply, Installation, Testing and commissioning of 25 meter high Flag mast pole as per the following specifications, including cost all materials, labor, lead, lift, transportation, supervision charges all complete as per approved design, make and as per the instruction of the Engineer- In-Charge; - Minimum 65 micron hot dip galvanized - 20 sided polygonal white PU coated - Suitable for wind speed of 50 m / s - Pole Top dia Min. 150 mm (A/F) - Pole Bottom dia Min 540 mm (A/F) - 4 Sections with sheet thickness of 4mm at Top ; 5 mm at middle and 6 mm at bottom - Base plate 670 mm dia ; 30 mmthick and PCD- 570MM - 12 No. M30 X 850 mm foundation bolts with nuts, washers’, template and anchor plate - Double drum winch, gear box belt, Gear Ratio 53:1, ; 3 Ph, 415V, AC motor of approved make, - 6mm (7/19 construction ) SS 304 grade wire rope. - Manual operating handle - Mounting plates for motor and Gear box - Lightning arrester and eaarthing spikes (GI) - Decorative GRP /FRP DOME. - LED low intensity, steady type aviation light with 3C X 2.5 Sqmm copper cable - Service door as specified size

Supply, Installation, testing & Commissioning of stand mounted IP55, 14SWG Powder coated, CRCA feeder pillar as per below specifications; Incomer : 1 No. 40 A, 4 P, MCB and 1 set of R,Y,B LED indication lamp Lighting Control: 1 No. 25 A, TP, Power contactor with 24 Hrs. single dial timer for the automatic switching of luminaires Power Tool Control: 2 No. 9A, TP, Power contactor and pendant push buttons with cable for raising & lowering of flagTerminals: 4 Nos 16 Sqmm Terminals for incomer, 4 Nos 10 Sqmm Terminals motor power supply & 4 Nos. 2.5 Sqmm Terminals for motor raise /lower control The cost should be inclusive of all material, labour, lead & lift, transportation, supervision charges and any requirement not specified for commissioning of the feeder pillar complete as per approval and instruction of Engineer-in- charge

Supply, installation, testing & commissioning of 350 W LED Flood light fitting, IP66, 350000lm, 6500 k complete including cost of all material, labour, lead, lift, transportation, supervision charges etc., as per approval and instruction of Engineer-in-charge

Supply, installation, testing & commissioning of Single Dome LED Aviation light of low intensity, steady type complete including cost of all material, labour, lead, lift, transportation, supervision charges etc., as per approval and instruction of Engineer-in-charge

Design, supply, installation, testing & commissioning of Earthing system as per IS 3043 including supply & fixing of 2.5 m long 40 mm Dia class-B GI pipe with clamps, nuts & bolts, including construction of earth pit PCC chamber size of 450 x 450 mm with steel frame CI cover. Providing Earth bus for interconnection & supply and filling the earth pit chamber with mixture of salt & charcoal complete including cost of all material, labour, lead, lift, transport, supervision charges etc., complete as per approval and instruction of Engineer-in-

Design, supply and erection of suitable RCC foundation suitable for 25 m high flag mast pole, considering the SBC of the site soil as 100 KN/SQM complete including cost of water proofing the foundation with approved material, cost of labour, lead, lift, formworks supervision charges etc., complete as per the approval and instruction of the Engineer-in-charge