Water Proofing Tenders

Description: BOQ ITEMS: Earthwork in excavation in the following types of soil and rock up to and including 1.5 mtr. Lead including bailing pumping out any water accumulating inside the excavated trench, shoring strutting adequate protection to be taken during excavation drilling blasting transporting the excavated soil for all lead stacking selectively including disposing off the rubbish rock fragments excess spoils etc. lead upto 100 Mtrs. in the area as directed by the Engineer all complete as per drawing specification and direction of the Engineer.All types of soil , Earthwork in excavation in the following types of soil and rock up to and including 1.5 mtr. Lead including bailing pumping out any water accumulating inside the excavated trench shoring strutting adequate protection to be taken during excavation drilling blasting transporting the excavated soil for all lead stacking selectively including disposing off the rubbish rock fragments excess spoils etc. lead upto 100 Mtrs. in the area as directed by the Engineer all complete as per drawing, specification and direction of the Engineer. In Ordinary rock, Earth work in back filling with available earth including watering and compaction at all elevations around foundations walls wells tunnels pits culverts trenches road approaches and in plinth filling and area filling as per specifications and drawings and as directed by the Engineer with selected spoil within a lead of 100 mtr., Disposal carriage of rubbish waste rock earth etc.dumped stacked at site by mechanical means including loading unloading and dressing properly lead upto 5 Km. and up to any lift includind cost of all labours and equipments. , Surface dressing of the ground in all kinds of soil including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish lead up to 50 m and lift up to 1.5 m., Supply mix place in position compact cure cement concrete 1 cement 3 coarse sand 6 graded stone aggregate 20 mm nominal size below foundations walls wells pits trenches etc. and in basin lining as per specifications drawings and directions of the Engineer and including cost of centring and shuttering but excluding cost of cement., Supply mix place in position compact and cure including testing of concrete specimens finishing surfaces as per specifications drawings and directions of the Engineer of the following grades of concrete with 20mm and down graded stone aggregate and coarse sand in super structure or any level excluding cost of centring shuttering cement and reinforcement. M20 RCC PCC, Taking delivery from store departmental yard bend bind and place the following types of reinforcement in all types of reinforced concrete work at all elevations including cleaning straightening cutting bending and binding with 18 SWG annealed wire or with welding such as tack lap butt etc with approved electrodes providing concrete cover blocks pins chairs nails supports of reinforcement etc. with all materials and labour complete as per drawings specifications and directions of Engineer excluding cost of reinforcement. , Install dismantle and remove the form work of approved quality including splay recess corners haunch etc. scaffolding necessary rendering of concrete surfaces after exposure including cost of all material and labours at all elevations. , Supply and laying in position brick work with designate 75 bricks in super structure etc in cement coarse sand mortar including mixing mortar laying bricks raking joints curing etc complete with all materials and labour as per drawings and specifications excluding cost of cement. , Providing and fixing 125 into 63 mm M. S. Hinges of approved quality and make., Providing and fixing ISI marked anodised aluminium tower bolt black finish Barrel type with necessary screws etc. complete 300 into 10 mm, Providing and fixing ISI marked anodised aluminium tower bolt black finish Barrel type with necessary screws etc. complete 150 into 10 mm, Providing and fixing bright finished brass hanging type floor door stopper with necessary screws etc. complete., Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer having brand logo with IS 3564 embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm with double speed adjustment with necessary accessories and screws etc. complete., Providing and fixing aluminium handles ISI marked anodised anodic coating not less than grade AC 10 as per IS 1868 transparent or dyed to required colour or shade with necessary screws etc. complete 125 mm., Providing and fixing aluminium sliding door bolts ISI marked anodised anodic coating not less than grade AC 10 as per IS 1868 transparent or dyed to required colour or shade with nuts and screws etc. complete 300 into 16 mm, Cement concrete flooring 1 cement 2 coarse sand 4 graded stone aggregate finished with a floating coat of neat cement including cement slurry but excluding the cost of nosing of steps etc. Complete as per direction of Engineer in charge excluding cost of cement. 40 mm thick with 20 mm nominal size stone aggregate, Grading roof for water proofing treatment with Cement concrete 1 cement 2 coarse sand 4 graded stone aggregate 20 mm nominal size excluding cost of cement, 15mm thick minimum plastering with 1cement 6 coarse sand to all faces of walls channels in roof and other structures at various elevations including mixing laying finishing curing and necessary scaffolding work complete as per drawings specifications and instructions of the Engr. with all materials and labours excluding cement Including Making grove if required. Work will be done upto 10 m height., Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer specification., Applying neat cement punning including cost of all materials labours etc. Complete as per direction of Engineer in charge excluding cost of cement, Supplying and applying two or more coats of white wash with lime to walls ceiling etc. At various elevations including preparation of surfaces cleaning etc.complete with all materials labour scaffolding work as per specifications ., Supplying and applying two or more coats of approved water proof cement paint over a coat of primer to exterior surfaces of concrete masonry plastered surfaces etc.at all elevations and including preparation of surface necessary scaffolding work etc.complete with all materials and labour Application of paint should be made as per manufacturer specifications to give an even shade. , Drain cleaning including disposal of rubbish up to 5 km all complete as per direction of EIC, Cleanning of chajja roof RWDC Floor corner drains etc., Painting with synthetic enamel paint of approved brand and manufacturer of required colour to give an even shade two or more coats on new old work over a priming coat complete as per specification and direction of Engineer in charge. , Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators side top centre hung with beading and all members complete of standard rolled steel sections joints mitred and flash butt welded and sash bars tenoned and riveted including providing and fixing of hinges, pivots including priming coat of approved steel primer but excluding the cost of other fittings complete all as per approved design sectional weight of only steel members shall be measured for payment Fixing with 15 into 3 mm lugs 10 cm long embedded in cement concrete block 1 Cement 3 coarse sand 6 graded stone aggregate 20 mm nominal size, Taking delivery from store departmental yard fabrication and erection of Structural steel work riveted bolted or welded in built up sections trusses and framed work including cutting hoisting fixing in position and applying a priming coat of approved steel primer all complete., Providing and fixing bright finished brass casement window fastener with necessary screws etc. complete., Providing and fixing oxidised M.S. casement stays straight peg type with necessary screws etc. complete., Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc. 15 mm dia nominal bore, Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc 20 mm dia nominal bore, Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc 25 mm dia nominal bore, Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc 50 mm dia nominal bore, Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc 100 mm dia nominal bore G.I. CPVC.., Fixing of old G.I. pipes complete with G.I. fittings including trenching and refilling etc. 15 mm dia nominal bore, Fixing of old G.I. pipes complete with G.I. fittings including trenching and refilling etc. 20 mm dia nominal bore, Fixing of old G.I. pipes complete with G.I. fittings including trenching and refilling etc. 25 mm dia nominal bore, Providing and fixing C.P. brass bib cock Pillar Cock of approved quality conforming to IS8931. 15 mm nominal bore., Providing and fixing C.P. brass stop cock concealed of standard design and of approved make conforming to IS 8931. 15 mm nominal bore., Making pocket size 0.20 into 0.20 into 1.0m , Demolishing brick work in cement mortar manually by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer in charge., Demolishing R.C.C.PCC work manually by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer in charge., Dismantling G.I. pipes external work including excavation and refilling trenches after taking out the pipes manually by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer in charge upto 150 mm dia, Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS 12818 and making good the same etc. complete as per direction of Engineer in charge., Providing and fixing Renewing glass panes with putty and nails wherever necessary including racking out the old putty Float glass panes of thickness 5.5 mm, Renewing of old glass putty, Supplying laying in position stone masonary with Hard rock boulder with cement morter 1cement isto 6coarse sand morter finishing the top with PCC 1 isto 2 isto 4 reasonably smooth complete with curing and raking of joints including cost of all material equipments and labour excluding cost of cement. , Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete., Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade Old work one or more coats, Supplying Grouting with Anchor NSG as per manufactureres instruction at any level and any place as per direction of Engineer in charge., Providing and fixing 35 mm thick factory made PVC door shutters with frame 65mm into 55mm with wall thickness 2 mm all complete as per manufacturers specification and direction of Engineer in charge. , Providing and fixing ISI marked flush door shutters conforming IS2202 non decorative type core of block board construction with frame of 1st class hard wood and well matched comercial 3 plyveneering with vertical grains or cross bands and face veneers on both faces of shutters 30 mm thick including ISI marked stainless steel butt hinges with necessary screws., Providing and fixing precoated galvanised iron profile sheets of 0.50 mm total coated thickness with zinc coating 120 grams per sqm in 240 mpa steel grade 5 microns epoxy primer on both side of the sheet and polyester top coat 15 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer in charge. The sheet shall be fixed using self drilling self tapping screws of size 5.5 into 55 mm with EPDM seal complete upto any pitch in horizontal vertical or curved surfaces including ridges barge board etc excluding the cost of purlins rafters and trusses and including cutting to size and shape , Providing and fixing Following precoated galvanised steel sheet roofing accessories 0.50 mm total coated thickness Zinc coating 120 grams per sqm in 240 mpa steel grade 5 microns epoxy primer on both side of the sheet and polyester top coat 15 microns using self drilling self tapping screws complete Ridges plain 500 to 600mm, Providing and fixing Following precoated galvanised steel sheet roofing accessories 0.50 mm total coated thickness Zinc coating 120 grams per sqm in 240 mpa steel grade 5 microns epoxy primer on both side of the sheet and polyester top coat 15 microns using self drilling self tapping screws complete. Barge board up to 300mm, Providing and fixing Following precoated galvanised steel sheet roofing accessories 0.50 mm total coated thickness Zinc coating 120 grams per sqm in 240 mpa steel grade 5 microns epoxy primer on both side of the sheet and polyester top coat 15 microns using self drilling self tapping screws complete . Gutter 600 mm over all girth, Providing reinforced by organic fibres or inorganic synthetic fibres cement 6 mm thick corrugated sheets roofing up to any pitch and fixing with polymer coated J or L hooks bolts and nuts 8 mm dia. G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc. complete excluding the cost of purlins rafters and trusses including cutting sheets to size and shape wherever required. , Providing and fixing Following fibre cement high impact polypropylene reinforced roofing accessories in all colours with polymer coated J or L hooks bolts and nuts and or G.I. seam bolts and nut G.I. plain and bitumen washers or with self drilling fastener and EPDM washer etc. complete. Close fitting adjustable ridges, Providing and fixing Following fibre cement high impact polypropylene reinforced roofing accessories in all colours with polymer coated J or L hooks bolts and nuts and or G.I. seam bolts and nut G.I. plain and bitumen washers or with self drilling fastener and EPDM washer etc. complete. Barge boards , Providing fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch including fixing with polymer coated J or L hooks bolts nuts 8mm dia. G.I plain bitumen washers complete but excluding the cost of purlins rafters trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets.The sheets shall be opaque or translucent clear or pigmented textured or smooth as specified. 2 mm thick corrugated as directed by EIC, Repairing and maitenance of Rolling shutter in all respect including greasing repairing replacement of material to repairing of rolling shutter. Supply and fixing 27.5 cm long springs., Repairing and maitenance of Rolling shutter in all respect including greasing repairing replacement of material to repairing of rolling shutter. Supply and fixing ball bearing, Supply and fixing precast slab 0f M20 grade, Repairing of false floor including providing and fixing PVC rigid foam sheet 1 mm thick on existing false floor boards shutters using synthetic rubber based adhesive all complete as per direction of Engineer in charge. , Providing wood work in frames of false ceiling floor partitions etc. sawn and fixed in position Sal wood and 15 mm thick light weight integral densified micro look edged with PVC top matt false floor tiles of size 595 into 595 mm including cost of all materials labours and as per direction of Engineer in charge. , Aluminum work for shutters of doors windows ventilators including providing and fixing hinges pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber neoprene gasket required Fittings shall be paid for separately Polyester powder coated aluminium minimum thickness of polyester powder coating 50 micron, Providing and fixing water closet squatting pan Indian type W.C. pan with 100 mm sand cast Iron P or S trap 10 litre low level white P.V.C. flushing cistern including flush pipe with manually controlled device handle lever with all fittings and fixtures complete including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580 into 440 mm with integral type foot rests., Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 into 260 into 350 mm or 340 into 410 into 265 mm sizes respectively., Providing and fixing wash basin Kitchen Sink with C.I. brackets, 15 mm C.P. Brass pillar taps 32 mm C.P. brass waste of standard pattern including painting of fittings and brackets cutting and making good the walls wherever require White Vitreous China Wash basin size 630 into 450 mm with a single 15 mm C.P. brass pillar tap all complete as per direction of EIC., Providing and fixing white vitreous china water closet squatting pan Indian typeOrissa pattern W.C. pan of size 580 into 440 mm, Supply and fixing PVC connecting pipe 15 mm N B, Supply and fixing PVC flexible waste pipe 32/40 mm N B, Supply and fixing float ball valve 20 mm N B, Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25 into 25 mm made of G.I. wire of dia 3 mm including strengthening with 2 mm dia wire or nuts bolts and washers as required complete as per the direction of Engineer in charge. , Dismantling steel work in built up sections in angles tees flats and channels including all gusset plates bolts nuts cutting rivets welding etc. including dismembering and stacking within 50 metres lead., Dismantling following roofing including ridges hip valleys and gutters etc.and stacking the material within 50 metres lead of G.S. Sheet..., Dismantling following roofing including ridges hips valleys and gutters etc.and stacking the material within 50 metres lead of Asbestos cement sheet, Providing and fixing PTMT grating of approved quality and colour Circular type 125 mm nominal dia with 25 mm waste hole.

Description: BOQ ITEMS: Earth work in excavation ( exceeding 30cm in depth 1.5 Mtr. in width or 10 Sq.m. on plan ) by mech/manual means including dressing of sides and ramming of bottoms, lift upto 1.5 mtr including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 mtr. All kinds of soil , Cleaning Jungle including uprooting of rank vegetation, grass, brush wood, trees and sapling of girth upto 30cm. Measured at a height of 1 m above ground level and removal of rubbish upto a distance of 2KM out side the periphery of the area cleared by your own vehicle., Providing and laying in position Plain cement concrete 1- 3 - 6 ( 1 Cement - 3 Coarse - 6 Graded stone aggregates 20 mm nominal size) excluding the cost of centering, shuttering in foundation, footings, and bases of column as per specifications and drawings and direction of Engineer in charge, Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, - All work up to plinth level .Grade-1-2-4 (1 cement - 2 coarse sand - 4 graded stone aggregate 20mm nominal size), Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering,- All work above plinth level .Grade- 1-1.5-3 (1 cement - 1.5 coarse sand - 3 graded stone aggregate 20mm nominal size), Providing and laying Hire and labour rate for fixing centering shuttering for concrete works to anywhere at any level (including staging) including strutting, propping etc. and removal of form or striking out after completion of works as directed and specified by the Engineer-in-charge.(Material for shuttering to supplied by the contractor) - a) Foundations, footings, bases of columns plinth beam etc, b) Suspended floors, roofs, landings, balconies, shelves etc., Providing and laying for Fixing steel reinforcement for reinforced cement Concrete work including transporting , decoiling, straightening, cutting, derusting bending, placing in position at all height and binding with binding wire etc. complete as per drawing, specification and instruction of the Engineer-in-charge. , Brick work with bricks of class designation 75 in foundation and plinth in- Cement mortar 1-6 (1 Cement - 6 Coarse sand) . , Brick work with bricks of class designation 75 in superstructure with cement mortar 1-6 (1 cement - 6 course sand) including all materials, labour, scaffolding, racking out joints, curing as per specification and direction of the Engineer-in-charge. , Providing and fixing factory made solid core, commercial flush door shutters non-decorative type, core of block board construction with well seasoned chemically treated timber of moisture content, not exceeding 12 per cent and side styles, top and bottom rails of main width as per I.S. Code, well seasoned hard wood chemically treated and well matched commercial ply veneering with vertical grains on cross bends on both faces of shutters, hot pressed and banded with phenol formaldehyde synthetic resin conforming to I.S./ 2202 (part - I) / 1930. a) 35mm thick shutter with 100mm oxidized S.S. butt hinges with necessary screws for double or single leaf shutters complete., Providing and fixing aluminum (Heavy type) sliding door bolts with nuts and screws etc. complete. a) 300 x 16mm, Providing and fixing anodized aluminum tower bolt including necessary screws etc. complete.250 X 10mm, Providing and fixing anodized aluminum door handle including necessary screws etc. complete.a) 125mm, Providing and fixing Structural steel work reveted,bolted or welded in built up sections, trusses and framed work ,including cutting hoisting, fixing in position and applying a priming coat of approved steel primer. , Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS - 13592 Type A, including jointing with seal ring conforming to IS - 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes.110 mm diameter, 12 mm cement plaster of mix - 1- 6 (1 cement - 6 coarse sand ), White washing with lime to give an even shade - New work (three or more coats)., Finishing walls with Premium Acrylic Smooth exterior paint(Weather Coat) with Silicone additives of required shade- New work (Two or more coats applied at the rate of 1.43 Itr/10 sqm over and including priming coat of exterior primer applied at the rate of 2.20 kg/10 sqm), Supplying and Painting with synthetic enamel paint/ aluminum paint of approved brand and manufacture Two or more coats in new work..Two or more coats in new work., Providing & fixing White vitreous china water closet squatting pan (Indian type) along with S or P trap including dismantling of old WC seat and S or P trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge. Orissa pattern W.C Pan of size 580x440 mm, Fencing with angle iron post placed at required distance embedded in cement concrete blocks, provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately). Payment to be made per metre cost of total length of barbed wire used- With G.I Barbed wire, Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. Made of G.I. wire of dia 4 mm, Providing and fixing white vitreous china wash basin with C.I./ M.S. brackets, 15mm C.P.brass pillar tap (single) 32mm C.P. brass waste of standard Pattern, including PVC waste pipe and PVC connector pipe including painting of fitting and brackets , cutting and making good the walls wherever required.a)Wash basin size- 550 X 400mm., Providing and fixing low level 10 litres capacity white P.V.C. flushing cistern with manually controlled device conformed to IS - 7231 with all fittings and fixtures complete Make-Hindware, Providing and fixing 32 mm dia. P.V.C. flexible waste pipes for sinks and wash basins., Providing and laying for fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. (Internal work) free of cost. a)15mm dia Nominal bore , a)20mm dia Nominal bore , Providing and fixing heavy duty C.P brass bib cock of 15mm nominal bore as per approved sample (Brand--Jaquar)., Grading of roof for water proofing treatment with cement concrete 1-2-4 (1 cement - 2 coarse sand - 4 graded stone aggregate 12mm nominal size) mix with Sika Top Seal and Sikadur 32 in appropriate proportion

Description: BOQ ITEMS: Toner Cartridge for printer Laser Jet MFP M438 nda (335S), Pencil cell model A, Pencil cell model 23A 12V, Vegitable basket 5 kgs cap with Lid, Vegitable basket 5 kgs cap without Lid, Umbrella large size, Cotton Rope 8 mm for tent , Heat Piller 1500 W, Pedestral Fan, Broom Phool (Jadu), Temperature and Humidity meter, Rain measuring cylinder, Precast concrete pillar for fixing of station point, TBM, RL and Centre line, Tarpaulin HDPE heavy duty 18 feet x 24 feet 2mm thick edges binded , Tarpaulin HDPE heavy duty 24 feet x 24 feet 2mm thick edges binded, Tape metalliic 30 mtr length, Mason thread (Cotton only), Paint synthetic enamel white, Painting brush 4 inch, Writing brush 1 inch, MS wire nails 17 Gauge 2 inch long, Safety Jacket, Dah Iron 10 inch with handle, S K Oil stove 1.5 ltrs (04 burner), Tea container Stainless Steeel 5 ltrs cap, Tiffin carrier 04 container , Lime unslacked, Hand gloves, Computer Window 10 Pro intel (R) Core(TM) i5 CPU 10000 8 GB RAM 1TB HDD 24 Inches Monitor, Colour Printer (HP Office Jet Pro 9720), UPS Champion KVA 150/61500 BAH, Computer chair revolving, Plastic chair with Arms, Plotter paper roll (45 Mtrs long), Photostat paper A4 size, Photostat paper A3 size, Photostat paper legal size, Printer cartridge HP laser Jet P1020 plus, Refill Ink for Epson L3210 colour printer (black, yellow, cyan, Magenta), Deep Freezer, Almirah steel medium size, Food serving counter 6 feet long, Shamiyana water proof size 30 feet x 30 feet with all accessories, Electric press heavy duty, Microwave oven, Sofa Set, CCTV Camera with all accessories, Work Station 06 Cabin (03 cabin each side), Pre Painted CGI Sheets of size 10 feet x 4 feet, Liner Sheets of size 10 feet x 3 feet for wall both side & back side, PGI Sheets of size 10 feet x 4 feet, MS Squire pipe 3 inch x 3 inch vertical post, MS Pipe 50 mm dia x 06 mtr, Paint red Oxide, Welding Rod 3.5 mm dia, Screw, Work Station 04 Cabin for Main Office, Quick Setting Compound, Steel Jerricane 20 Ltrs cap, Water Storage Tank 1000 Ltrs cap, Water Storage Tank 1500 Ltrs cap, Water Storage Tank 2000 Ltrs cap, Water Storage Tank 500 Ltrs cap, Water Storage Tank 200 Ltrs cap, HDPE Barrels 200/210 Ltrs cap, Paint Synthetic Enamel Grey, Paint Synthetic Enamel Olive Green, Paint Synthetic Enamel P O Red, Paint Epoxy Red with Hardener, Base paint Grey, Paint Synthetic Enamel Yellow, Paint Synthetic Enamel Black, Paint Epoxy White with Hardener, Paint Epoxy Red with Hardener, Paint Terracotta Red, Thinner, Paint Synthetic Enamel White, Distemper White, Paint Red Oxide, Thermoplastic Paint White for Road Marking as per IS 164 1981, PVC Switch Board 8 inch x 4 inch, Socket with Switch 16 Amp, Socket with Switch 6 Amp, PVC Copper Wire 2 Sqm 90 mtr Roll, PVC Copper Wire 1.5 Sqm 90 mtr Roll, PVC Copper Wire 1 Sqm 90 mtr Roll, Insulation Tape 20 mm width 25 Mtr length, Led Tube Light 2 feet Long 20 W complete set, Almirah Double door small Size, Dust Bin 20 Ltrs Cap plastic, Besrah Niwar Black Rubber Door Mat, Turkey Cotton Towel White small for wash Room, LT Wire 6 MM 25 Mtr roll, LT Wire 4 MM 25 Mtr roll, LT Wire 2.5 MM 25 Mtr roll, LT Wire 2 MM 25 Mtr roll, LT Wire 1.5 MM 25 Mtr roll, LT Wire 1 MM 25 Mtr roll, LT Wire 0.75 MM 25 Mtr roll, Charpoy Bed with Ply top 6 feet 6 inch x 3 feet 6 inch, Mattress 6 feet 6 inch x 3 feet 6 inch, Dining Table wooden 6 seater for offr, Dining Table wooden 6 seater for JCO, Dining Table wooden normal 6 seater for ORs, Dining Chair wooden, Dining Chair plastic, RO Plant 50 L/Hr Cap, Executive Table for OC big, Executive Table for Offr Normal, Executive Chair for OC, Executive Chair for Offr Normal, Office Table Normal, Office Chair Non revolving, Almirah Steel Large size 78 inch x 36 inch x 19 inch, Visitors Chair, Heat Pillar 1500 W, Sofa Set (05 seater)

Description: CATEGORY: TMT Bar 10 mm , TMT Bar 12 mm , TMT Bar 8 mm , White Cement , Caping Casing , Casing Caping , False Ceiling 2 Ft x 2 Ft including all accessories , Ceiling Rose , Gypsum Bd False Ceiling 2 Ft x 2 Ft , Drapery Rod 25 mm with Socket and Bracket , Peg Stay of 6 hooks , Water Proof Plastic , Bullet Proof Glass 45 x 30 cm , Single Bunk with Cushion , CP Tap , LED Panel light 2 Ft x 2 Ft , Stainless Steel hand wash basin , Cloth Hanger , Cloth Hook , CP Cloth Hook , CP Cloth Hook with Six Hook , Curtain Rod , Cushion Chair Stainless Steel , Cushion for double bunk bed , Cushion with Ply , Door CGI Sheet , Door Glass , Double Bunk , Double Bunk with Cushion , Float Ball , Glass Putty , HDPE Jerrican 35 Ltr , Hessian Cloth , J Hook , LAIP 6 Ft , Lime Stone , M Seal , Mattress , Mattress for Bunk Bed with Ply , Mattress with Ply , Mesh Door , Mirror 48 x 44cm , MS Handle 150 mm , PBS Roll , PBS Roll with 20mtr Long , Ply board , Ply Board 4 ft x 8 ft and 12mm thick , Ply with Cushion , Plywood for false ceiling , Plywood , Plywood 4 Ftx 6 Ft , Plywood 6 x 4 x 12 , Plywood 6 Ft x 3 Ft with Cushion , Plywood 9 mm 8 Ft x 4 Ft , Plywood With Mattress , Primer Red , Single Bunk with cushion , Sleeping Double Bunk , Sleeping double bunk with cushion , SS Jali 4 inch Dia , Stainless Steel Chairs with arms fitted back cushion , Stainless Steel Dispenser , Steel Rack of size 1.20mx1.80x4 having three shelters , Steel Racks , Steel Writing Table of Size 1220x750x60mm with three drawer , Tarpin Oil , Thinner , Wall Putty , White Wash , Wooden Bed , Wooden Board 4 inchx6 inch , Wooden Cabinet 0.75x0.40x0.80m , Wooden Cabinet 0.75x0.40x0.80m with one shelf , Wooden Cabinet of size 1.75 x0.4 x0.80m with one shelf in middle comn , Wooden Table with drawer , Wooden Table 1.40m x 0.70 x 0.75m , Wooden Table of size 1.40 x 0.75m with drawer , Wooden Table with Drawer , Wood primer , White safeda , Angle Valve , Elbow , GI Pipe 0.5 Inch , CP Shower , GI Elbow 20 mm , Gate Valve 15 mm , Gate Valve 40 mm , Gate Valve , GI Elbow 15mm , GI Elbow 20mm , GI Pipe 1 inch , GI Pipe 0.5 inch , GI Pipe 20 mm , Hand Shower , L Angle MS 3 mm , MS Drainage , Nipple 15mm , Nipple 20 mm , GI Pipe 15 mm , Pipe Wrench , PVC Pipe , PVC pipe 110mm , PVC Pipe 20 feet 4 inch Dia , PVC Pipe 4 inch Dia , PVC Pipe T 2 inch , PVC Pipe T 3 inch , PVC Pipe 0.5 inch , PVC Round Block , GI Socket Reducer , Sockage Pit Cover , SS Soap Disk , Union 15 mm , Health Faucet , Union 20 mm , PVC Pipe 4 ft Dia , Aluminium Door , Apex Red Paint , Apex White Paint , Bus Green Paint , CGI Sheet 10 Ft long , Clamp for PVC Section Pipe 2 inch , Cutting Blade 14 inch , Cutting Blade 4 inch , Emery Paper , Float Ball 20 mm complete , GI Socket 20 mm , Grinding wheel 8 inch , Heavy Hinges , Malmal cloth , MS angle 1 inch x 1 inch 5 mm , MS Flat 15 mm x 3 mm , MS Pipe 1.5 inch x 1.5 inch x 5 mm , MS Sheet 8 Ft x 4 Ft , MS Square Pipe 1.5 inch x 1.5 inch x 3 mm , Paint Black , Paint Brown , Paint Red Oxide , Paint White , Punched Tape Concertina Coil , PVC Connection Pipe , PVC Section hose pipe 2 inch , Sand Paper , Sand Paper 60 Nos Roll , Self Tapping Screw 2 inch , Sliding Door , Square Pipe 1 inch x 1 inch , Square pipe 1.5 inch x 1.5 inch , Square Pipe 3 inch x 3 inch x 20 Ft long , Stop Cock 20 mm , T.T Oil , Touchwood Paint , Wall Putty 40 Kg , Wall Stainer 100 gm , Welding Rod , Wood Filler Putty , Wood Stain , Yellow Sienna , Socket 5 Amp , Socket 15 Amp , Switch 5 Amp , PVC Switch Bd 8 inch x 10 inch , Floor tiles 400 mm x 400 mm , Geyser 25 Ltrs , PVC Cable 16 sqmm 2 core Al Conductor

Description: Dismantling old and damaged cement concrere including cost of all labour T&P etc. complete in all respects , Dismantling old and damaged Brick Work including cost of all labour T&P etc. complete in all respects , Scraping old white or colour wash including disposal of refuse as directed by the Engineer in charge with in a distance of 60 meters., Supplying & Placing of Murga Jali on roof including cost of all material, labour T&P etc. complete in all respects, Cement Concrete 1 1.5 3 Over murga jali on roof with water proffing compound including cost of all material, labour T&P etc. complete in all respects, Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sqm. And under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including diposal of rubbish to the dumping ground all complete as per direction of Engineer in charge with cement mortar 1 4 (1 cement 4 coarse sand), Providinding and applying white cement based putty of average thickness 1 mm,of approved brand and manufacture, over the plastered wall surface to preparethe surface even smooth complete., Wall Painting with plastic emulsion paint of approved brand and manufacture to give an even shade one or more coats on old work. etc. including cost of materials, labour,T&P complete in all respects, Finshing walls with premium accrylic smooth exterior paint with silicon addetives of required shade old work over existing cement paint surface. etc. including cost of materials, labour,T&P complete in all respects, Providing and laying vitrified floor tiles in size 600mmx 600mm of approved make including joint filled with white cement etc. including cost of materials, labour,T&P complete in all respects , Renewal old putty of glass pans etc. including cost of materials, labour,T&P complete in all respects , Renewing glass pannes, with putty and nails whereever necessary including racking out the old putty. Float glass panns of nominal thickness 4 mm etc. including cost of materials, labour,T&P complete in all respects , Painting and Varnishing on iron works in small area approved suprior quality ready mixed paint of clear synthetic varnish including supply of material, labour and T&P etc for proper completion of work. , Dismantling of W.C pan of all size etc. including cost of materials, labour,T&P complete in all respects , Dismantling of tile work laid down cement mortar including upto 50 meter disposal including cost of all material, labour T&P etc. complete in all respects, Providing and laying ceremic glazed Floor Tiles of size 300x300 mm of Ist quality of approved make in colours laid on 20 mm thick cement mortor 1 4 jonting including the joint filling with white cement. including cost of all material, labour T&P etc. complete in all respects, Providing and fixing White Vitreous China Wall Mouting Water Closet squating pan (European type 780x370x690m pan) with low level white PVC flushig system, including flus pipe manually control device (handle lever) with all fitting and fixture complete, including cutting making wood the wall and floors wherver required.including cost of all material, labour T&P etc. complete in all respects , PVC Wall Panelling hot stamping and lamination,water proof ,temper proof on walls and celling etc including cost of materials, labour,T&P complete in all respects , Providing & Fixing 15mm Dia CPVC Pipes including cost of materials, labour,T&P complete in all respects., Providing & Fixing 15 mm Dia C.P. Brass Bib Cock including cost of materials, labour,T&P complete in all respects., Providing & Fixing 15 mm Dia C.P. Brass Stop Cock including cost of materials, labour,T&P complete in all respects. , Providing & Fixing 15 mm Dia C.P. Brass Angle Valve including cost of materials, labour,T&P complete in all respects., Providing & Fixing Wash Basin including cost of materials, labour,T&P complete in all respects., Providing & Fixing P.V.C. waste Pipe for wash basin including cost of materials, labour,T&P complete in all respects., Wiring point for light with 1.5 sq.mm P.V.C. insulated and P.V.C Sheathed T.R.S. single core cable with1.5 sq.mmP.V.C. insulatedT.R.S. single core cable Earth etc complete in all respects. , Wiring point for fan with 1.5 sq.mm P.V.C. insulated and P.V.C Sheathed T.R.S. single core cable with1.5 sq.mmP.V.C. insulatedT.R.S. single core cable etc complete in all respects. , Wiring point for Plug with 1.5 sq.mm P.V.C. insulated and P.V.C Sheathed T.R.S. single core cable with1.5 sq.mmP.V.C. insulatedT.R.S. single core etc complete in all respects. , Wiring point for call bell with 1.5 sq.mm P.V.C. insulated and P.V.C Sheathed T.R.S. single core cable with1.5 sq.mmP.V.C. insulatedT.R.S. single core etc complete in all respects.

Details: Description:- Supply, Installation, Testing, And Commissioning Of Exterior Bis Registered 36w 24v Dc Rgbw linear Led Wall Washer Luminaire For Facade Lighting With Extruded Aluminum Housing, Powder-coated Finish, And clear Toughened Glass. With All Leds On, Minimum System Lumen Efficacy Equal To Or Greater Than 62.9 Lm/w. the Luminaire Shall Be Capable Of Producing Dynamic Color-changing Light With 16 Million Colors As The Light Fixture should Be Programmable Using 8-bit Control Dmx512 Protocol / Ethernet-based Control. The Luminaire Should Be complete With A Dedicated Lens Made Up Of Ul/vde Approved Pc For Each Led, Offering Beam Angle Of Different types Such As Narrow, Medium, Wide, Or Elliptical As Per The Site Requirement. The Fixture Should Be Erected With the Necessary Required Brackets And Should Have Constant Locking Hinges For Simple Position Control From Various angles Without Special Tools. The Fixture Shall Be Suitable To Operate At An Ambient Temperature Range Of -30°c To 50°c And The Complete Luminaire Shall Be Ip66 And Ik07 Rated. Led Life Time Shall Be At Least L70@ 25c @ 50000burninghoursat25°c.ledshouldbeofnichia/osram/seoul/philips/ lumileds/cree/lednium/avago Make. The Product Should Be Bis Approved With R Number Mentioned On product Label. To Be Supported With Product Test Reports - Lm79, Bis Report And Leds Test Reports. Luminaire shall Be Conforming To Bis I.e. Is 10322 (part 5/sec 5) And Shall Be Complete With All Necessary Accessories required For Proper Working Of Fixture Including Weather Proof Connection Cables, Water Proof Connectors Etc. As required. This Includes Crane Charges If Any For Height Work.(warranty Period Of 5 Years). All Test Reports And technical Data Sheets To Be Submitted To The Competent Authority For Approval. After Installation, Assembling And commissioning Contractor Should Ensure That All Parts Of The Light Are Properly Fixed And Put It Into Running condition. The Entire Work Should Be Carried Out As Per The Instructions Of Site Engineer. Testing Of The Fixtures To be Done In The Presence Of Site Engineer For A Minimum Period Of 1 Week.

Details: Description:- Supply, Installation, Testing, And Commissioning Of Exterior Bis Registered 24w 24v Dc Rgbw linear Led Wall Washer Luminaire For Facade Lighting With Extruded Aluminum Housing, Powder-coated Finish, And clear Toughened Glass. With All Leds On, Minimum System Lumen Efficacy Equal To Or Greater Than 62.9 Lm/w.the luminaire Shall Be Capable Of Producing Dynamic Color-changing Light With 16 Million Colors As The Light Fixture should Be Programmable Using 8-bit Control Dmx512 Protocol / Ethernet Based Control. Luminaire Should Be complete With A Dedicated Lens Made Up Of Ul/vde Approved Pc For Each Led, Offering Beam Angle Of Different types Such As Narrow, Medium, Wide Or Elliptical As Per The Site Requirement. The Fixture Should Be Erected With the Necessary Required Brackets And Should Have Constant Locking Hinges For Simple Position Control From Various angles Without Special Tools. Fixture Shall Be Suitable To Operate At An Ambient Temperature Range Of -30°c To 50°c And Complete Luminaire Shall Be Ip66 And Ik07 Rated. Led Life Time Shall Be At Least L70@ 25c @ 50000 burning Hours At 25°c. Led Should Be Of Nichia/osram/seoul/philips/ Lumileds /cree /lednium / avago Make. The Product Should Be Bis Approved With R Number Mentioned On Product Label. To Be Supported with Product Test Reports - Lm79, Bis Report And Leds Test Reports. Luminaire Shall Be Conforming To Bis I.e. is10322 (part 5/sec 5) And Shall Be Complete With All Necessary Accessories Required For Proper Working Of Fixture including Weather Proof Connection Cables, Water Proof Connectors Etc. As Required. This Includes Crane Charges if Any For Height Work. (warranty Period Of 5 Years). All Test Reports And Technical Data Sheets To Be Submitted To the Competent Authority For Approval. After Installation, Assembling And Commissioning Contractor Should Ensure that All Parts Of The Light Are Properly Fixed And Put It Into Running Condition. The Entire Work Should Be Carried Out as Per The Instructions Of Site Engineer. Testing Of The Fixtures To Be Done In The Presence Of Site Engineer For A minimum Period Of 1 Week

Details: All The Extinguishers Shall Be Kept In Healthy Working Condition.check And Inspect The Condition / Operational Readiness Of Fire Extinguishers.check And Inspect Expiry Date On Fire Extinguishers.empty Cylinders And Expired Cylinders Shall Be Segregated And Listed For Refilling.carry Out The Refilling Works Of Co2,mechanical Foam,water Co2 And Abc Fire Extinguishers For Those Cylinders Which Are Empty And Crossed Expiry Date With Approval From Enginer In-charge And All Refilling Works Of Mechanical Foam,water Co2 And Dcp Shall Be Carried Out At Bhadra Generating Station Itself. Refilling Of Co2 And Abc Fire Extinguishers Shall Be Carried Out At Firm Works And Refilled Cylinders Shall Be Brought Back And Installed Within 07 Days.all Defective And Damaged Parts / Spares Of The Fire Extinguishers Shall Be Listed And Submitted. Such Damaged Parts / Spares Shall Be Supplied And Replaced With Approval From Engineer In-charge Within Reasonable Time. Check / Inspect And List Out Defective Fire Extinguishers And Issue Condemnation Certificate.carryout The Pressure Testing Of Water Co2, Mechanical Foam, Dcp, Abc And Co2 Type Fire Extinguishers Once In The Contract Period.carry Out Quarterly Over All Supervision And Maintenance Of The Fire Extinguishers System In A Year And Label The Cylinders For Healthiness And Next Due Date Of Maintenance. Water Proof Labels / Covers Shall Be Used For Outdoor Fire Extinguishers. Refilling / Recharging Shall Be Carried Out Using Quality Materials Only. The Spare For Fire Extinguishers Parts Shall Be Supplied By Kpcl.there Are 06 Fire Hydrant Points At Left Bank Power House And 02 Fire Hydrant Points At Right Bank Power House Of Bhadra Generating Station.carry Out Quarterly Over All Supervision And Maintenance Of The Fire Hydrant Systems In A Year And Report Shall Be Submitted For Healthiness Of The System. Carry Out Checks Of All The Fire Hydrants For Its Operational Readiness.checking Of Pipelines, Valves, Nozzles, Hoses, Hose Reel Drums And Couplings For Healthy Condition. Any Abnormalities In The System Shall Be Rectified With Approval From Engineer In-charge.the Firm Has To Conduct Fire Fighting Training In Theory, Practical And Panic Mock Drill Once In A Year. The Training Program Shall Be Conducted At Bhadra Generating Station. Time And Date Of The Training Program Shall Be Decided And Intimated By Engineer In-charge.

Details: Multi Positioning Portable Maintenance Lamp With Dual Mounting System ( powerful Magnetic + Normal Base For Floor Operation.) Fitted With 36 Watt Led Cob ( make Cree Or Similar) Hsn Code - 8413 Fitted With Battery Low Indicator . Fitted With Bis C ertified Powerful Lithium Battery (lasting Continuous Glowing 7-8 Hrs 24v, 14000 Mah. provided With Electric Charger. Make/brand - Om Energy Savers Or Similar.[ Technical S pecifications :- (1) Light Source :- Smd Led . (2) Light Power :- 36 Watt, 4000 Lumens. (3) Le d Type :- Smd Led Cluster .(4) Light Spectrum Colour :- White : 6000 Digree K Approx. (5) radiation Angle :- > 90 Digree. (6) Heat Dissipation Method :- Aluminium Diecast Fixture back With Fins . (7) Battery Type :- Lithium Ion. Bis Certified . (8) System Voltage :- 24v Sy stem .(9) Battery Certification :- Bis Certified Battery (govt. Of India) . (10)battery Ove r Charge Protection :-.(11)battery Deep Discharge Protection (12) Battery Short Cir cuit Protection (13) Thermal Cut-off Protection (14) Charging Type :- Electric.(15)cha tging Time :- 5-6 Hours Approx. (16) Backup Time /run Time :- High Mode : 7 To 8 Hours Med mode : 15 To 16 Hours . (17) Battery Low Indicator :- Provided + Buzzer Beep Warning. (1 8) Operating Modes :- High Mode, Mid Mode .(19) Rubber / Silicon Gasket :- Provided For water & Dust Resistance.(20)toughened Glass .(21) Sturdy Aluminium Enclosure (22) In gress Protection :- Ip65. (23) Single Switch Operation With One Additional Main Power switch Water Proof Switch .(24) Water Proff Switch 25)power Ful Magnet With Non -m agnetic Isolation Disc Capable Of Complete Weight. (26) Dual Mounting System :- (a) Ma gnetic Surface Mounting Capability (b) Base H Stand Mounting Capability. (27) Carry H andle With Cushioning For Carry Comfort.(28) Powder Coated Ms Base Stand & Carry handle . (29) Warranty :- 1 Year

Details: Ldl Cholestrol With Calibrator,2x30m,2x10ml , Hba1c With Calibrator Set,2x15ml,2x5ml , Xl Multical,4x3ml , Autowash, Ac,al, 5x4ml , Autowash Kit,10x100ml , Erba Norm Kit , Erba Path Kit , Urea 5x22ml,5x 6point8ml , Micro Albumin With Calibrator 1x5ml,2x25ml , Calcium 5x6ml , Creatinine,jaffes,5x44ml,5x11ml , Glucose,10x44ml , Triglycerides ,5x11ml,5x4ml , Cholesterol,5x11ml , Hdl Cholestrol With Calibrator, 4x30ml,4x10ml , Erba Norm 4x5ml , Erba Path 4x5ml , Multical 4x3ml , Erba H3 Control Hematology,qc , Director Ldl R1 2x30,r2 2x10 , Erba 180 Cuveette , Rotar , Erba Wash Solution System Pack 10,100ml , Alkaline Phosphatase R1 2x44,r2 , Sgot R1, 4x35ml,r2 4x18 Point1 Ml , Albumin R1 10x44ml , Direct Hdl R1-4x30ml,r2-4x10ml , Crp R1 1x40ml,rx 1x10ml , Aso 1x22,1.5x5 , Sgpt R1 4x35ml,r2 4x18point1ml , Plate Sealer, 100 Per Pk , Water Proof Temperature And Humidity Data Logger , Anti A,b,c,d Blood Grouping Kit , Anti H Lectin Antisera , Anti A1 Lectin Antisera