Telangana Tenders

Aluminium Step Ladder 16 Feet Height.the Stiles Of The Ladder Should Be Made Of Alu-c-sections While The Steps Made Of Heavy Duty Aluminum Non-slippery.the Top And Bottom End Are Fitted With Rubber.steps Must Be Strong Enough To Support At A Time Weight Of 01 Men (80kg Total)with Warranty As Per Is4571/1977 Or Latest

Supply Of Pressurised Flushing System

Supply Of Cartridge Portable Oil Filtration Unit With Flow Rate 1200 Ltr/hr With Pump, Motor, Trolley Arrangement For Tm Division, Stage-ii/btps

Supply Of Impulse Lines And Accessories For Local Instruments Racks Towards Tg & Tg Aux Side Of C&i Division Of Stage-ii/btps

Hy8540340038 - Bearing Shell Assembly Dia 300mm Ptp - As Per Specification, Drawing And Pqc Attache

CATEGORY: Dismantling the cryogenic soldering contacts , Dismantling the vacuum chamber with probes , Dismantling the control unit the power supplies for magnets , Demounting the electromagnet , Dismantling the water chiller and pipe connections , Disconnecting the He compressor pipe lines , Assembling and reinstalling the Cryogenic probe station with magnet.

CATEGORY: Drawing Sheet , Cutting Wheel 4 inch , Cutting Wheel 14 inch , Grinding Wheel 4 inch , Buffing Wheel 4 inch Steel , Buffing Wheel 4 inch cotton , Hacksaw Blade 2 side 1 inch , Angle 3mm , Square Pipe 2mm , Flat Patti 3mm , Round Pipe 2mm , MS Sheet 18 gauge , MS Plate 6mm , Armr Plate 15mm , MS Sheet 24 gauge , MS Sheet 22 gauge , CGI Sheet Corrugated , Armr Rod Electrode , Welding Rod E 6013 , Tungsten Electrode Green , Tungsten Electrode Red , TIG Welding Torch Nozzle Kit , Refilling of Oxygen Gas , Refilling of Acetylene Gas 3CB , MS Copper Coated Filler Rod , Brass Filler Rod 1mm , Copper Filler Rod 2mm , Bronze Flux Powder , Copper Pipe Half Inches , Solder Soft , Zinc Chloric Acid , Zinc Sheet , Kerosine , Coal , Round Bar 12mm , MS Plate 1 inch , Pop Rivets 1 point 5 inch , Snap Rivets , A4 Sheet 75 GSM , J Hook 2 inch with nut and washer , Moulding Sand , Alluminium , Graphite Crucible , Drill Bits 2mm to 13mm

CATEGORY: Solid Carbide End Mill Dia 1mm 4 Flute Helix Angle 30 deg , Solid Carbide End Mill Dia 2mm 4 Flute Helix Angle 30 deg , Solid Carbide End Mill Dia 3mm 4 Flute Helix Angle 30 deg , Solid Carbide End Mill Dia 4mm 4 Flute Helix Angle 30 deg , Solid Carbide End Mill Dia 5mm 4 Flute Helix Angle 30 deg , Solid Carbide End Mill Dia 6mm 4 Flute Helix Angle 30 deg , Solid Carbide End Mill Dia 7mm 4 Flute Helix Angle 30 deg , Solid Carbide End Mill Dia 8mm 4 Flute Helix Angle 30 deg , Solid Carbide End Mill Dia 9mm 4 Flute Helix Angle 30 deg , Solid Carbide End Mill Dia 10mm 4 Flute Helix Angle 30 deg , Solid Carbide End Mill Dia 11mm 4 Flute Helix Angle 30 deg , Solid Carbide End Mill Dia 12mm 4 Flute Helix Angle 30 deg , Solid Carbide End Mill Dia 13mm 4 Flute Helix Angle 30 deg , Solid Carbide End Mill Dia 14mm 4 Flute Helix Angle 30 deg , Solid Carbide End Mill Dia 15mm 4 Flute Helix Angle 30 deg , Solid Carbide End Mill Dia 16mm 4 Flute Helix Angle 30 deg , Solid Carbide End Mill Dia 17mm 4 Flute Helix Angle 30 deg , Solid Carbide End Mill Dia 18mm 4 Flute Helix Angle 30 deg , Solid Carbide End Mill Dia 19mm 4 Flute Helix Angle 30 deg , Solid Carbide End Mill Dia 20mm 4 Flute Helix Angle 30 deg