Modular Tenders

Description: CATEGORY: 3TX40012A , CONTACTOR RELAY TYPE 3TH30400APO M RATED CURRENT 10A COIL VOLTAGE 230V AC WITH 4 NO , AUX CONTACTOR TYPE 3TH30220BM4 10A COIL VOLTGE 220 DC 2NO and 2NC CONTACTS MAKE SIEMENS , FRONT DRIVE PROVIDED WITH DOOR INTERLOCKING DETECT AND PAD LOCKING ARRANGEMENT FOR 3KM52 CAT NO 8UC63 , Contact block for Push button Selector Key actuators Rear mounting 1NC Type 3SB54 00 0C Make Siemens , CONTACTOR RELAY 415V 2NO and 2NC COIL 230V TYPE 3TH30220AP0 MAKE SIEMENS , AC POWER CONTACTOR 3TF53 RATED CURRENT 205A AUXILIARY CONTACTS 2 NO and 2 NC COIL VOLTAGE 230V AC CAT NO 3TF53 02 OAPO Make Siemens , POWER CONTACTER TYPE 3TF56 , Power Contactor Siemens Make 3TS 51 for Blue Star make water cooled screw chiller , AUX CONTACTOR TYPE 3TH30 230V AC COIL SIEMENS MAKE WITH ADD ON AUX CONTACTS 2NO and 2NC EXTRA , CONTACT AUX BLOCK 1NO TYPE 3TX40102A COIL VOLT 220V 240V , 2 POLE ON or OFF SWITCH TYPE 3LAO2054YA RATING 25A 415 V , Voltmeter selector switch Type 3ST1 400 1RK08 Make Siemens , Modular push button actuator Opaque With holder for contact block Normal button Red colour button Type 3SB50 00 0AC01 Make Siemens , OVERLOAD RELAY 3US58008Y8K SIEMENS make for Blue Star make water cooled screw chiller , Bimetal Overload Relay 1 to 1.6 A Type no 3UA50001A MAKE SIEMENS , AUX CONTACT BLOCK 1NO TYPE 3TX40102A MAKE SIEMENS , AIR BREAK POWER CONTACTOR TYPE 3TF3400OAPO 32A IE AC3 AT 415V AC COIL VOTAGE 230V AC MAKE SIEMENS , 45A Power contactor with 2NO and 2NC aux cnt 110V AC Coil Size 3 Type 3TF4602 OAFO Make SIEMENS , MAIN CONTACT KIT FOR 3TF477 CONTACTOR MODEL NO 3TY74770YA , Contactor 09A Type 3TF30100BB4 Coil Voltage 24V DC , THERMAL OVER LOAD BIMETAL RELAY WITH SINGLE PHASING PROTECTION FOR CONTACTOR MOUNTING RANGE 1.25 to 2 AMPS TYPE 3UA50001B Make Siemens , POWER CONTACTOR TYPE 3TF31 230V AC COIL RATED CURRENT 12A WITH 2NO and 2NC AUX CONTACTS EXTRA SIEMENS MAKE , AUX CONTACT BLOCK 1NC TYPE 3TX40012A MAKE SIEMENS , THERMAL OVER LOAD BIMETAL RELAY WITH SINGLE PHASING PROTECTION FOR CONTACTOR MOUNTING RANGE 0.8 to 1.25 AMPS TYPE 3UA50000K Make Siemens , THERMAL OVER LOAD BIMETAL RELAY WITH SINGLE PHASING PROTECTION FOR CONTACTOR MOUNTING RANGE 10 to 16 AMPS TYPE 3UA52002A Make Siemens , AIR BREAK POWER CONTACTOR TYPE 3TF4702OAPOZAO1 AUX CONTACTS 2NO and 2NC 63A IE AC3 AT 415V AC COIL VOTAGE 230V AC MAKE SIEMENS , THERMAL OVER LOAD BIMETAL RELAY WITH SINGLE PHASING PROTECTION FOR CONTACTOR MOUNTING RANGE 16 to 25 AMPS TYPE 3UA52002C Make Siemens , Main Contact Kits For 3TF48 Contactor Type 3TY7 480 0YA , S Bimetal Overload Relay 2.5 to 4 A Type no 3UA52001 E MAKE SIEMENS , INDEPENDENT MOUNTING KIT TYPE 3UX1420 , POWER CONTACTOR 9A 1 NO 230V AC TYPE 3TF30100AP0 MAKE SIEMENS

Description: CATEGORY: Piano Type Modular Domestic Fan Regulator as per IS 11037 (Q3) , PVC back for hair verandah map as per drawing 4mm thick weight not less than 1 point 85 , Chair seat and back , Foam cushion size 16 x 17x75 mm thick 32 denscity duly covered with 12mm thick plywood at bottom and leather rexin mehroon , Prelaminated partical board 8 feet x 4 feet x 15mm , Foam cushion size 21 x 22x4 thick duly covered whithtapasty cloth , wooden beading patti 2 point to 3mtrs , wooden beading patti 1 point 5 point 6 to 2mtrs , furniture polish or waxes 100gm pkt , Tapasty cloth cover for foam cushion of size 21x22x4 as per sample , seat for chair , sofa cloth cover 46 , led bulb 12watt , led round warm white 15 divide 18w celling light , junction box for street light , cable copper standard round shaeathed 3 core 2 point 5 sqmm , cable coper standard round shaeathed 3 core 1 point 5 sqmm , straight through joint for xlpe cable 11kv of size 240 sqmm , indoor end joint for xlpe cable 11kv of size 240 sqmm , straight through joint for xlpe cable 11kv of size 300 sqmm , straight through joint for xlpe cable 11kv of size 95 sqmm , xlpe cable allminum conductor 3 point 5 core 35 sqmm 11kv , xlpe cable allminum conductor 3 point 5 core 70 sqmm , xlpe cable allminum conductor 3 point 5 core 50 sqmm 11 kv , straight through joint for xlpe cable of size 70 to 95 sqmm , theromostate for gyser free size , LED bulb 7 watt , LED bulb warm white 7 watt , Cable pvc insulated aluminum conductor 2 core 10 sqmm , cable pvc insulated aluminum conductor 2 core 6 sqmm , wall mounting fancy light fitting 14 watt , straight through joint for xlpe cable 11 kv of size 120 sqmm , Gun metal gate valve 50mm with iron wheel head , Non return valve 200mm , xlpe cable allminum conductor 2 core 25 sqmm 11 kv , xlpe cable allminum conductor 4 core 16 sqmm 11 kv , Indoor end joint kit for xlpe cable 11 kv of size 120 sqmm , Indoor end joint kit for xlpe cable 11 kv of size 185 sqmm , Gun metal gate valve 40 mm , Glass pan pin headed 3 point 5 mm 4 feet x 3 feet sheet , water tank cover suitable for tanks 500 divide 1000 ltrs , CP soop dish , forget valve 20 mm bore half turn , Oil putty , Holder for 25mm curtain rod , Stop cock PVC 15mm , Door stooper steel with single rubber , Recess mounting led luminaries 18 watt 1x1 , MCCB 4 pole 160amp 25 ka , Driver led 60 watt , led bulb 9 Watt , cable copper standard round sheathed 3 core 4 sqmm , Non return valve 80 mm , PVC casing 25 x 3 mtr , Tullu pump for desert cooler submersible , Alluminium sliding door bolt 300mm , Sluice valve 150mm , Xlpe cable 4 core 25 sqmm , MCB 3 pole 40 Amp , MCB single pole 10 Amp , MCB single Pole 32 Amp , MCCB 3 pole 100 amp , MCB single pole 16 Amp , Ding dong bell , Insulation tape 20 x 25 mtr , Glass pane frassen 4 x 4 x4mm , Glass pane plain 4x3x3mm , Glass pane frassen 4x4x3mm , 3pin plug ISI marked 16Amp , Sink coupling 100mm , PVC float valve 20mm , PVC connection 15mm x 24 inch , PVC connection 15mm x 18 inch

Details: (version 2) - Healthcare Institute; Prefabricated Walls and Ceiling Panels For Antibacterial Paint And Primer complte In All Aspect; Service Provider , Repair, maintenance, And Installation Of Plant/ Systems/equipments (version 2) - Healthcare Institute; Ot Light Complte In all Aspect; Service Provider , Repair, Maintenance, And installation Of Plant/ Systems/equipments (version 2) - healthcare Institute; Electrical Distribution Panel complte In All Aspect; Service Provider , Repair, maintenance, And Installation Of Plant/ Systems/equipments (version 2) - Healthcare Institute; Storage Unit complte In All Aspect; Service Provider , Repair, maintenance, And Installation Of Plant/ Systems/equipments (version 2) - Healthcare Institute; Other Misc Job Works in Modular Ots Complte In All Aspect; Service Provider , repair, Maintenance, And Installation Of Plant/ systems/equipments (version 2) - Healthcare Institute; cmc For Hermitically Sealed Door 1000x2100; Service provider , Repair, Maintenance, And Installation Of Plant/ systems/equipments (version 2) - Healthcare Institute; cmc For Hermitically Sealed Door 1800x2100; Service provider , Repair, Maintenance, And Installation Of Plant/ systems/equipments (version 2) - Healthcare Institute; cmc For Surgeon Control Panel; Service Provider , Repair, maintenance, And Installation Of Plant/ Systems/equipments (version 2) - Healthcare Institute; Cmc For Hatch Box; service Provider , Repair, Maintenance, And Installation Of plant/ Systems/equipments (version 2) - Healthcare institute; Cmc For Xray Viewing Screen; Service Provider , repair, Maintenance, And Installation Of Plant/ systems/equipments (version 2) - Healthcare Institute; cmc For Antistatic Flooring; Service Provider , Repair, maintenance, And Installation Of Plant/ Systems/equipments (version 2) - Healthcare Institute; Cmc For Pressure relief Damper P R D; Service Provider , Repair, maintenance, And Installation Of Plant/ Systems/equipments (version 2) - Healthcare Institute; Cmc For Scrub Sink unit; Service Provider , Repair, Maintenance, And installation Of Plant/ Systems/equipments (version 2) - healthcare Institute; Cmc For Ots Peripheral Led Lights; service Provider , Repair, Maintenance, And Installation Of plant/ Systems/equipments (version 2) - Healthcare institute; Cmc For Single Arm Ceiling Pendent; Service provider , Repair, Maintenance, And Installation Of Plant/ systems/equipments (version 2) - Healthcare Institute; cmc For Laminar Air Flow With Hepa Diffuser Cloth; Service provider , Repair, Maintenance, And Installation Of Plant/ systems/equipments (version 2) - Healthcare Institute; cmc For Prefabricated Walls And Ceiling Panels For antibacterial Paint And Primer; Service Provider , Repair, maintenance, And Installation Of Plant/ Systems/equipments (version 2) - Healthcare Institute; Cmc For Stryker Make ot Light; Service Provider , Repair, Maintenance, And installation Of Plant/ Systems/equipments (version 2) - healthcare Institute; Cmc For Electrical Distribution

Description: CATEGORY: Fuel Filter Genr Set 40 KVA , Fan Belt Alternator 45 No Genr Set 40 KVA , Oil Filter Genr Set 40 KVA , Fuel Feed Pump Genr Set 40 KVA , ABR 3 Phase Genr Set 40 KVA , High Pressure pipe Genr Set 40 KVA , Fuel Filter Genr Set 5 KVA , Fuel Filter Genr Set 30 KVA , Oil Filter Genr Set 30 KVA , Fan Belt Genr Set 30 KVA , Fuel Pipe Main Genr Set 30 KVA , Door Hinges Genr Set 30 KVA , Hours meter Genr Set 30 KVA , Emergency Stopper Genr Set 30 KVA , Bty Lid Negative and Positive Genr Set 30 KVA , Bty 12V 90AH Genr Set 30 KVA , Door Hinges Genr Set 40 KVA , Trinity VAF Meter Genr Set 40 KVA , Air Filter Genr Set 30 KVA , MCB 63 Amp 3 Phase Genr Set 30 KVA , Air Cleaner Genr Set 30 KVA , Oil Filter Element Genr Set 30 KVA , Change over Switch 63 Amp Genr Set 30 KVA , Flexible wire 2Sqmm 2 core Genr Set 30 KVA , Flexible Wire 1.5 Sqmm Single core Genr Set 30 KVA , Fuel Filter Genr Set 7.5 KVA , Fuel Filter pipe Genr Set 7.5 KVA , Oil Filter Genr Set 7.5 KVA , Air Filter Genr Set 7.5 KVA , Fan Belt Genr Set 7.5 KVA , Oil Filter Genr Set 25 KVA , Fuel Filter Genr Set 25 KVA , Fan Belt Genr Set 25 KVA , Benjo Bolt 19 mm Genr Set 25 KVA , Fuel Tank Cap Genr Set 25 KVA , Fuel Filter Genr Set 15 KVA , Oil Filter Genr Set 15 KVA , Fuel Pipe line Genr Set 15 KVA , Fan Belt Genr Set 15 KVA , Benjo Bolt Genr Set 15 KVA , Fan Belt Genr Set 36 KVA , Oil Filter Genr Set 36 KVA , Air Filter Genr Set 36 KVA , Fuel Filter Genr Set 36 KVA , Fuel pipe Genr Set 36 KVA , Over Flow Pipe Genr Set 36 KVA , MCB 63 Amp 3 Phase Genr Set 36 KVA , Change over Switch 63 Amp Genr Set 36 KVA , Fuel Pipe Genr Set 30 KVA , Fuel Filter Genr Set 1.4 KVA , Oil Filter Genr Set 1.4 KVA , Engine Oil Genr Set 1.4 KVA , Fuel Filter Genr Set 10 KVA , Oil Filter Genr Set 10 KVA , Engine Oil Genr Set 10 KVA , RO Chemical RO Plant 5000 LPD , Ro Wessel RO Plant 5000 LPD , Sand Carbon RO Plant 5000 LPD , Corel Sand RO Plant 5000 LPD , RO Membrane PC 250LPH RO Plant 5000 LPD , PP Spun Filter RO Plant 5000 LPD , MCB 63 Amp DP , MCB 32 Amp DP , MCB 16 Amp SP , Plywood 8 feet x 4 feet x 12mm , Maint of AC and Gas Filling , Water Tank 500 Ltrs , PVC Cable 2.5 Sqmm 2 core , Cement Bags , MCB Box 4 way , 15 Amp Switch Socket , 16 Amp Switch Socket , Plug 3 Pin 15 Amp , Hinges 100m Long , Window Glass 550x530x400 mm , LED Bulb 18 W , LED Tube Light 20W 4 feet Long , HDPE water tank Tank 200 ltr triple layer , Toilet Paper Stand Toilet Paper dispenser , PVC Plastic curtain 6 feet x 3 feet , PVC Door 6 feet x 3 feet , Sintex Loft Tank 500 ltrs , Looking Mirror 1 feet x 1.4 inch , Bib TAP 15mm , Curtain with Rod , Wash basin , Flush cistern 10 ltrs for Fd Toilet , Paint RFU Red , Paint RFU White , Paint RFU Black , Service Wire PVC 4 sqmm 2 core , Looking Mirror 1.5 feet x 2 feet , LED Bulb 9W , Shower Pipe , Wastage Pipe , Synthetic Enamel Paint Olive Green Colour , CFL 10W LED 12W , 15 Amp Switch , 16 Amp Socket , LED Bulb 5 W , Synthetic Enamel Paint brown Colour , Paint white , LED ceiling Light 10W , Sand Bag , CFL 11W , 5 Amp Modular Switch and Socket , Exhaust Fan , Welding Rod , Water Tank 1000L triple layer , Synthetic Enamel Paint Sand Colour , Synthetic Enamel Paint black colour

Description: CATEGORY: Cable XLPE LT UG Armd 2 x 6 Sqmm , Cable PVC 2x6 sq mm copper conductor , Cable PVC Almn SC 10 Sqmm , Cable PVC Almn TC 4 Sqmm , Cable PVC Almn TC 6 Sqmm , Cable PVC Copper SC 01 Sqmm , Cable PVC Copper SC 10 Sqmm , Cable XLPE LT UG Armd 4 x 16 Sqmm , Cable XLPE LT UG Armd 3.5 x35 Sqm , Capacitor running 15MFD 5 for AC , Capacitor running 45or 50MFD 2 for AC , Capacitor running 50 or 60MFD 4 for AC , Capacitor running 50MFD 5 for AC , Change over switch 100A TPN , Flood light 60W LED , Flood light 90W LED , Flood light 110W LED , Flood light 30W LED , Flood light 45W LED , Street light 110W LED , Street light 30W LED , Street light 90W LED , Fuse wire 14 SWG , Heat Shrinkable 120 Sqmm 3 core Joint kit , Heat Shrinkable 185 Sqmm 3 core Joint Kit , Heat Shrinkable 95 Sqmm 3 core Joint Kit , Isolator 100A 4 Pole , Isolator 100A TP , Lugs 10mm copper , Lugs 120mm Almn , Lugs 16mm copper , Lugs 185mm Almn , Lugs 240mm Almn , Lugs 25 mm Almn , Lugs 300mm Almn , Lugs 630mm Almn , Lugs 6mm copper , Lugs 95mm Almn , MCCB 100 Amp TP 25 KA or 36KA , MCCB 125 Amp TP 25 KA or 36KA , MCCB 160 Amp TP 16 KA , MCCB 160 Amp TP 25 KA or 36KA , MCCB 200Amp 3 pole 25 or 36 KA , MCCB 400 Amp TPN 36KA , MCCB 63 Amp TP 16 KA , Tape adhesive PVC 20 mm 15 Mtr long , Tape adhesive PVC 25 mm 15 Mtr long , AC Box with MCB 16 Amp SP , Bed switch piano type 5 or 6 Amp , Bipin holder , Cable flat PVC flex submerssible seathed 3 core 2.5sqmm , Cable flat sumerceble sheathed 3 core 6 Sqmm , Cable PVC Almn Two core 1.5 Sqmm , Cable PVC Almn 10 Sqmm TC , Cable PVC Almn SC 1.5 Sqmm , Cable PVC Almn SC 6 Sqmm , Cable PVC Almn two core 2.5 Sqmm , Cable PVC copper 3 core 48 .20mm , Cable PVC copper insulated multi strand Two core 1.5 Sqmm , Cable PVC Copper SC 2.5 Sqmm , Cable PVC Copper SC 4 Sqmm , Cable PVC copper SC 6 Sqmm , Call bell ding dong , Capacitor 2.5 MFD , Capacitor 4 MFD , Isolator 63A 4Pole , LED bulb 12 watt , LED Bulb 14W or 15W , LED Bulb 18W , LED bulb 5 watt , LED bulb 7 watt , LED bulb 9 watt , LED Panel 1x4 Feet 40 Watt , LED Panel 2x2 Feet 40 Watt , LED Tube light 18 W Batten , LED Tube light Rod 20 Watt , FTL Box type fitting 1x20 W LED in lieu of Florocent Tube Light , MCB DB 4 Way TPN double door , MCB SP 10 Amp , MCB SP 16 Amp , MCB SP 20 Amp , MCB SP 6 Amp , MCB SP 63 Amp , MCB SPN 16A , MCB SPN 20 A , MCB SPN 25 A , MCB SPN 32 A , MCB SPN 40 A , MCB SPN 63 A , MCB TP 63A , MCB TPN 63A , MCB TPN 32A , MCB TPN 40 A , Plug Top 16 Amp three pin , Plug Top 6 Amp three pin , Regulator electronic type for ceiling fan , Socket modular 16A 3 pin , Socket multi purpose 6 and 16 A 6 pin , Socket Piano type 16 Amp 3 and 5 pin , Socket Piano type 6 Amp 3 and 6 pin , Switch socket 15 Amps Box type , Switch Socket comb Box type 16 A 6 pin , Switch Socket comb. Box type 6 or 5 A 5 pin , Switch PT 16 Amp one way , Switch PT 6 Amp one way , Switch PT 6 Amp two way , Tape adhesive PVC 15 mm 15 Mtr long

Description: BOQ ITEMS: Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead, New plaster in Old dismentilling wall 12 mm cement plaster of mix 1 ratio 6 1 cement ratio 6 coarse sand, Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface Water thinnable cement primer, Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2 point 5 sq meters and under including cutting the patch in proper shape raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the duming ground within 50 metres lead With cement mortar 1 ratio 4 1 cement 4 fine sand, Providing and fixing water closet squatting pan Indian type W C pan with 100 mm sand cast Iron P or S trap 10 litre low level white P V C flushing cistern including flush pipe with manually controlled device handle lever conforming to IS 7231 with all fittings and fixtures complete including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W C pan of size 580 into 440mm with integral type foot rests, Providing and fixing white vitreous china pedestal type water closet European type W C pan with seat and lid 10 litre low level white P V C flushing cistern including flush pipe with manually controlled device handle lever conforming to IS 7231 with all fittings and fixtures complete including cutting and making good the walls and floors wherever required W C pan with ISI marked white solid plastic seat and lid, Providing and fixing Chlorinated Polyvinyl Chloride CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain brass threaded fittings fixing the pipe with clamps at 1 point 00 m spacing This includes jointing of pipes fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge Concealed work including cutting chases and making good the walls etc 20 mm nominal outer dia Pipes, Providing and fixing soil waste and vent pipes Centrifugally cast spun iron socket and spigot S and S pipe as per IS 3989 100 mm dia, Providing and fixing soil waste and vent pipes Centrifugally cast spun iron socket and spigot S and S pipe as per IS 3989 75 mm dia, Providing and filling the joints with spun yarn cement slurry and cement mortar 1ratio 2 1 cement 2 fine sand in S C I and C I Pipes 75 mm dia pipe , Providing and filling the joints with spun yarn cement slurry and cement mortar 1 ratio 2 1 cement ratio 2 fine sand in S C I and CI Pipes 100 mm dia pipe , Providing and fixing plain bend of required degree 100 mm dia Sand cast iron S and S as per IS 1729, Half brick masonry with common burnt clay F P S non modular bricks of class designation 7point 5 in superstructure above plinth level up to floor V level Cement mortar 1 ratio 3 1 cement ratio 3 coarse sand, Providing and laying cement concrete in retaining walls return walls walls any thickness including attached pilasters columns piers abutments pillars posts struts buttresses string or lacing courses parapets coping bed blocks anchor blocks plain window sills fillets sunken floor etc up to floor five level excluding the cost of centering shuttering and finishing 1ratio 1 and half ratio 3 1 cement ratio 1and half coarse sand 3 graded stone aggregate 20 mm nominal size, Providing and fixing plain bend of required degree 75mm dia Sand cast iron S and S as per IS 1729, Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead For thickness of tiles above 25 mm and up to 40 mm, Providing and fixing Chlorinated Polyvinyl Chloride CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1point 00 m spacing This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge 25 mm nominal dia Pipes, Providing and fixing double scaffolding system cup lock type on the exterior side up to seven story height made with 40 mm dia M S tube 1 point 5 m centre to centre horizontal and vertical tubes joining with cup and lock system with M S tubes M S tube challies M S clamps and M S staircase system in the scaffolding for working platform etc and maintaining it in a serviceable condition for the required duration as approved and removing it there after The scaffolding system shall be stiffened with bracings runners connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc complete as per directions and approval of Engineer in charge The elevational area of the scaffolding shall be measured for payment purpose The payment will be made once irrespective of duration of scaffolding, Reinforced cement concrete work in walls any thickness including attached pilaster buttresses plinth and string courses fillets columns pillars piers abutments posts and struts etc above plinth level up to floor five level excluding cost of centering shuttering finishing and reinforcement 1ratio1and half 3 1 cement 1and half coarse sandzone III derived from natu ral sources 3 graded stone aggregate 20 mm nominal size derived from natural sources, Centering and shuttering including strutting propping etc and removal of form for Suspended floors roofs landings balconies and access platform and , Distempering with 1st quality acrylic distemper ready mixed having VOC content less than 50 gms per litre of approved manufacturer of required shade and colour complete as per manufacturer specification, Finishing walls with Acrylic Smooth exterior paint of required shade Old work Two or more coat applied 1point 67 ltr per 10 sqm on existing cement paint surface

Description: BOQ ITEMS: Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead, New plaster in Old dismentilling wall 12 mm cement plaster of mix 1ratio 6 1 cement 6 coarse sand, Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface Water thinnable cement primer, Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2 point 5 sq meters and under including cutting the patch in proper shape raking out joints and preparing and plastering the surface of the walls complet including disposal of rubbish to the duming ground within 50 metres lead With cement mortar 1 ratio 4 1 cement 4 fine sand, Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS 15622 thickness to be specified by the manufacturer of approved make in all colours shades except burgundy bottle green black of any size as approved by Engineer in Charge in skirting risers of steps and dados over 12 mm thick bed of cement mortar 1 ratio 3 1 cement 3 coarse sand and jointing with grey cement slurry 3point 3kg per sqm including pointing in white cement mixed with pigment of matching shade complete, Providing and laying Ceramic glazed floor tiles of size 300 into 300 mm thickness to be specified by the manufacturer of 1st quality conforming to IS 15622 of approved make in colours such as White Ivory Grey Fume Red Brown laid on 20 mm thick cement mortar 1ratio 4 1 Cement 4 Coarse sand Jointing with grey cement slurry 3 point 3 kg per sqm including pointing the joints with white cement and matching pigment etc complete, Providing and fixing water closet squatting pan Indian type W C pan with 100 mm sand cast Iron P or S trap 10 litre low level white P V C flushing cistern including flush pipe with manually controlled device handle lever conforming to IS 7231 with all fittings and fixtures complete including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W C pan of size 580 into 440mm with integral type foot rests, Providing and fixing wash basin with CI brackets 15 mm C P brass pillar taps 32 mm C P brass waste of standard pattern including painting of fittings and brackets cutting and making good the walls wherever require White Vitreous China Flat back wash basin size 550 into 400 mm with single 15 mm CP brass pillar tap, Providing and fixing Chlorinated Polyvinyl Chloride CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings fixing the pipe with clamps at 1point 00 m spacing This includes jointing of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge Concealed work including cutting chases and making good the walls etc 20 mm nominal outer dia Pipes, Providing and fixing soil waste and vent pipes Centrifugally cast spun iron socket spigot pipe as per IS 3989 100 mm dia For waste water, Providing and fixing soil waste and vent pipes Centrifugally cast spun iron socket and spigot S and S pipe as per IS 3989 75 mm dia, Providing and filling the joints with spun yarn cement slurry and cement mortar 1 ratio 2 1 cement 2 fine sand in SCI andC I Pipes 75 mm dia pipe , Providing and filling the joints with spun yarn cement slurry and cement mortar 1ratio2 1 cement 2 fine sand in S C I and GI Pipes 100 mm dia pipe , Providing and fixing plain bend of required degree 100 mm dia Sand cast iron S and S as per IS 1729, Half brick masonry with common burnt clay F P S non modular bricks of class designation 7 point 5 in superstructure above plinth level up to floor V level Cement mortar 1ratio 3 1 cement 3 coarse sand, Providing and laying cement concrete in retaining walls return walls walls any thickness including attached pilasters columns piers abutments pillars posts struts buttresses string or lacing courses parapets coping bed blocks anchor blocks plain window sills fillets sunken floor etc up to floor five level excluding the cost of centering shuttering and finishing 1ratio 1 an d halfratio 3 1 cement 1 and half coarse sand 3 graded stone aggregate 20 mm nominal size, Providing and fixing 18 mm thick gang saw cut mirror polished premoulded and prepolished machine cut for kitchen platforms vanity counters window sills facias and similar locations of required size approved shade colour and texture laid over 20 mm thick base cement mortar 1ratio 4 1 cement 4 coarse sand joints treated with white cement mixed with matching pigment epoxy touch ups including rubbing curing moulding and polishing to edges to give high gloss finish etc complete at all levels Raj Nagar Plain white marble Udaipur green marble Zebra black marble Area of slab over 0 point 50 sqm, Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead, Providing and fixing 600 into 450 mm beveled edge mirror of superior glass of approved quality complete with 6 mm thick hard board ground fixed to wooden cleats with C P brass screws and washers complete, Providing and fixing P V C waste pipe for sink or wash basin and urinal including PV C waste fittings complete 32MM, Providing and fixing 100 mm sand cast Iron grating for gully trap, Providing and fixing uplasticised PVC connection pipe with brass 45 CM, Providing and fixing C P brass stop cock concealed of standard design and of approved make conforming to IS 8931 15 MM, Providing and fixing plain bend of required degree 75mm dia Sand cast iron S and S as per IS 1729, Providing and fixing C P brass angle valve 15mm nominal bore, Providing and fixing C P brass bib cock of approved quality conforming to 15 mm nominal bore, Providing and laying water proofing treatment in sunken portion of WCs bathroom etc by applying cement slurry mixed with water proofing cement compound consisting of applying a First layer of slurry of cement 0 point 488 kg per sqm mixed with water proofing cement compound 0 point 253 kg per sqm This layer will be allowed to air cure for 4 hours b Second layer of slurry of cement 0 point 242 kg per sqm mixed with water proofing cement compound 0 point 126 kg per sqm This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours The rate includes preparation of surface treatment and sealing of all joints corners junctions of pipes and masonry with polymer mixed slurry , Centering and shuttering including strutting propping etc and removal of form for Suspended floors roofs landings balconies and access platform and , Distempering with 1st quality acrylic distemper ready mixed having VOC content less than 50 gms per litre of approved manufacturer of required shade and colour complete as per manufacturer specification

Description: BOQ ITEMS: SOFA- Three Seater Seating Capacity- 3 Seater Sofa Frame Covering - Fully Upholstered Covering Material for Seat and Backrest - Fabric Frame Structure Material and size (Plus Minus 1 mm) - MILD STEEL STRUCTURE Frame Structure Material and size (Plus Minus 1 mm) any other wood of minimum 19 mm thickness. Seat Cusion Material - foam Length of Three Seater Units in mm (Plus Minus 10 mm) 2150 Depth of Sofa Units in mm (Plus Minus 10 mm) 700 Density of Cushion of Backrest Material (Kg/Cubic M) 40 Sofa Height (Without Back Cushion) Plus Minus 5 (mm) 700 millimeter Sofa Height (With Back Cushion) Plus Minus 5 mm 800 millimeter Arm Width Plus Minus 5 (mm) 200 millimeter Arm Height Plus Minus 5 (mm) 710 millimeter Thickness of Foam in arms Plus Minus 2 (mm) 50 Colour of Polish on exposed Wood frame wood colour Springs shall be of best quality and indian make and of size 6 Inch/7 Inch as required and minimum 12 nos per seat of sofa. Cloth shall be provided as approved by Enginee-in-Charge & shall be minimum Rs. 600 per meter if differs amount will be deducted as difference of rate with addition of 50% Contractor profit. Bottom portion of sofa will be sealed with markeen etc as directed by Engineer-In-Charge. All other material like jute/rubberpad etc. if and as required shall be of best quality. WARRANTY PERIOD IN NUMBER OF YEARS- 03 Years, SOFA- Single Seater Seating Capacity- 1 Seater Sofa Frame Covering - Fully Upholstered Covering Material for Seat and Backrest - Fabric Frame Structure Material and size (Plus Minus 1 mm) - MILD STEEL STRUCTURE Frame Structure Material and size (Plus Minus 1 mm) any other wood of minimum 19 mm thickness. Seat Cusion Material - foam Length of Single Seater Units in mm (Plus Minus 5 mm) 850 Depth of Sofa Units in mm (Plus Minus 10 mm) 850 Density of Cushion of Backrest Material (Kg/Cubic M) 40 Length of Single Seater Units in mm (Plus Minus 5 mm) -850 Sofa Height (Without Back Cushion) Plus Minus 5 (mm) 700 millimeter Sofa Height (With Back Cushion) Plus Minus 5 mm 800 millimeter Arm Width Plus Minus 5 (mm) 200 millimeter Arm Height Plus Minus 5 (mm) 710 millimeter Thickness of Foam in arms Plus Minus 2 (mm) 50 Colour of Polish on exposed Wood frame wood colour Springs shall be of best quality and indian make and of size 6 Inch/7 Inch as required and minimum 12 nos per seat of sofa. Cloth shall be provided as approved by Enginee-in-Charge & shall be minimum Rs. 600 per meter if differs amount will be deducted as difference of rate with addition of 50% Contractor profit. Bottom portion of sofa will be sealed with markeen etc as directed by Engineer-In-Charge. All other material like jute/rubberpad etc. if and as required shall be of best quality. WARRANTY PERIOD IN NUMBER OF YEARS- 03 Years, Providing Executive Revolving Chair (Medium Back Type) as per details below- Type of backrest support Backrest, backrest symmetrical lumbar support, Overall Chair Height - 920mm, Backrest Height - 460mm, Backrest Width - 480mm to 500mm, Seat Height - 450 mm (Plus Minus 15mm), Seat Width - 500mm to 520mm, Thickness of M S Plate Joining the under structure with Seat 0.3mm to 0.5mm, Wheel base made of MS covered with chrome polish, Thickness of Plywood used in Seat (Plus Minus 1 mm) - 15mm to 18mm, Thickness of Plywood used in Backrest (Plus Minus 1 mm) - 15mm to 18mm, Back size - Medium back chair, Colour - as per choice seat material PU Foam covered with Fabric or leatherite Arm Material - Propylene Warranty- 02 Years, Providing & Placing of mobile pedestal unit 400X450X650mm in size (with or without wheel) having 3 drawers with single locking arrangement and chrome finished mettalic handles, laminated in colour with matt finish 0.6 - 0.8 mm thickness. Warranty- 02 Years, Providing & Placing Steel Almirah (Big) as per details below- Providing steel almirah of size 1855X910X480mm (hxwxd) having 4 adjustable shelves making 5 compartments without locker fabrication almirah side, back top, bottom & shelves are made from mild steel sheet not less than 22 guage and without any burrs & dent. The shelves shall have lipped flange 25 mm width 15mm in depth. The shelves are fitted to rack strips made of mild steel sheet of 20 gauge thick with help of 4 brackets of 16 guage that for support and adjustment and are having load bearing capacity of 90 kg uniformity divide load per shelf. The doors are made of mild steel sheet not less than 20 guage and are having metal stiffener suitably spot welded to stiffen the door and fited with the body with the help of but type hinges made of mild sheet sheet not less that 18 guage thickness double folded for free & smooth movement of doors. Weight of Steel Almirah should be more than 60 Kg. Warranty - 02 Years, Closed Metal Shelving Rack (Big) Type of Rack - CLOSED FROM SIDES AND BACK Height - 1875mm (Plus Minus 20 mm), Width - 900mm (Plus Minus 20 mm), Depth - 400mm (Plus Minus 15 mm) , Shelves Material - 1.0 mm Thick MS Sheet Conforming to Commercial Quality CR-1, Grade 340 of IS 513, Sides, Back and Partition Wall Thickness (Minimum) (mm) - MS Sheet 0.8 mm, Angle Posts Material and size - Rolled steel angle posts of 40 X 40 X 4 mm, Number of Shelves/Compartments (Top / Ceiling Shelf - not to be counted) - Minimum 05 nos, Weight of shelf (complete) - 35 Kg (Min.) Finish - Powder Coated, Warranty - 02 Years, Providing Executive office table (1800X900X750mm) with side storage unit & mobile pedestal unit Length of Table - 1800mm (Plus Minus 15mm), Width of Table - 900mm (Plus Minus 15mm), Top of Table - 42mm thick (minimum), Length of side unit - 1200mm (Plus Minus 10mm), Width of side unit - 450mm (Plus Minus 10mm), Table Top Finish - Laminate in color with matt finish 0.6-0.8mm thickness of type S, F or P having index no.3.2.3 conforming to IS 2046/Latest with having balancing laminate of 0.5mm thick on another side Provision of Keyboard Tray - Yes, No. of cabinet / drawer - 02 No (lockable), No. of Shutter - 02 No (Lockable), Length of pedestal unit - 850mm (Plus Minus 10mm), Width of pedestal unit - 450mm (Plus Minus 10mm), No. of drawer in pedestal unit - 03 Nos, Thickness of frame material - 25mm (Plus Minus 0.5mm), Colour - as per requirement, Warranty- 02 Years, Providing Executive office table (1500X750X750mm) with computer table & mobile pedestal unit Length of Table - 1500mm (Plus Minus 15mm), Width of Table - 750mm (Plus Minus 10mm), Top of Table - 25mm thick (minimum), Length of side unit - 900mm (Plus Minus 10mm), Width of side unit - 450mm (Plus Minus 10mm), Type of Material - Prelaminated Particle Board, Provision of Keyboard Tray - Yes, No. of cabinet / drawer in computer table - 01 No (lockable), Length of pedestal unit - 450mm (Plus Minus 10mm), Width of pedestal unit - 450mm (Plus Minus 10mm), No. of drawer in pedestal unit - 03 Nos, Thickness of frame material - 18mm (Plus Minus 0.5mm), Colour - as per requirement, Warranty- 02 Years, Providing Executive office table (2100X900X750mm) with computer table & mobile pedestal unit Length of Table - 2100mm (Plus Minus 15mm), Width of Table - 900mm (Plus Minus 15mm), Top of Table - 42mm thick (minimum), Length of side unit - 1200mm (Plus Minus 10mm), Width of side unit - 450mm (Plus Minus 10mm), Type of Material - Prelaminated Particle Board, Provision of Keyboard Tray - Yes, No. of cabinet / drawer - 02 No (lockable), No. of Shutter - 02 No (Lockable) Length of pedestal unit - 850mm (Plus Minus 10mm), Width of pedestal unit - 450mm (Plus Minus 10mm), No. of drawer in pedestal unit - 03 Nos, Thickness of frame material - 25mm (Plus Minus 0.5mm), Colour - as per requirement, Warranty- 02 Years, Modular cabinet type side unit (Close Type) Length of Table - 1500mm (Plus Minus 15mm), Width - 450mm (Plus Minus 10mm), Height - 750mm (Plus Minus 10mm) Type of frame - Internal frame of 18mm thick prelaminated particle board added to 18mm thick external frame, Door Shutters - Yes (made up of prelaminated particle board), No. of Drawers - 03 Nos Drawers with 03 Nos Swing drawers, Locking arrangement - Yes, Top of table - 25mm thick post forming, Type of finish - laminated in required colour, Warranty- 02 Years, Providing Visitors Chair (Non-Revolving)-Leatherite as per details below- Type of backrest support Backrest, backrest symmetrical lumbar support, Type of Chair - Visitors Chair (Leatherite), Overall Chair Height - 950 mm (Plus Minus 15 mm), Backrest Height - 500mm to 570mm, Backrest Width - 500 mm (Plus Minus 10mm), Seat Height - 480 mm (Plus Minus 5 mm), Seat Width - 500 mm (Plus Minus 10 mm), Seat Depth - 500 mm (Plus Minus 10 mm), Chair Type - With Arms Thickness of plywood used in seat (Plus Minus 1mm)- 18 mm Arm length- 200 to 300mm Arm width- 30 mm Arm Material- CRCA Pipe Thickness of polyurethane foam used in Backrest in mm (Plus Minus 3mm) 40 mm frame material- Chrome on MS Warranty - 02 Years, Wooden Center Table 600x600mm with glass top Length of Table 600mm (Plus Minus 20mm), Width 600mm (Plus Minus 15mm), Height 460mm (Plus Minus 15mm) Type of frame- Wooden No. of Legs- 04 Nos of size 45mmx45mm Table should be polished as per required shade. Glass top should be of superior quality and required shade having thickness 10mm (+0.5mm) Warranty- 02 Years, Executive Revolving Chair (High Back Type) Type of backrest support Backrest, backrest symmetrical lumbar support, Overall Chair Height - 1025mm to 1125mm, Backrest Height - 630mm to 700mm, Backrest Width - 480mm to 500mm, Seat Height - 500 mm (Plus Minus 15mm), Seat Width - 500mm to 520mm, Thickness of M S Plate Joining the under structure with Seat 0.3mm to 0.5mm, Wheel base made of MS covered with chrome polish, Thickness of Plywood used in Seat (Plus Minus 1 mm) - 15mm to 18mm, Thickness of Plywood used in Backrest (Plus Minus 1 mm) - 15mm to 18mm, Back size - High back chair, Colour - as per choice seat material PU Foam covered with Fabric or leatherite Arm Material - Metal Arms finished with matching fabric / leatherite Warranty- 02 Years, Providing & Placing High Back Ergonomic Chair as per details below- Type of backrest support backrest with lumber support of polypropylene at multilevel across back & Ergonomic Seat Design, Backrest is made of two pcs injection moulded frame Overall Chair Height 1125 mm, Backrest Height Plus Minus 15mm 600 millimeter, Backrest Width 480 millimeter, Seat Height 520 mm, Seat Width 500 mm, Thickness of MS Plate Joining the under structure with Seat 0.5 millimeter, Wheel base made of MS covered with chrome polish, Thickness of Plywood used in Seat Plus Minus 1(mm) 12 mm, Colour - Black or as per requirement seat material PU Foam covered with Fabric or leatherite Arm Material - Propylene Warranty - 02 Years, Providing & Placing High Back Ergonomic Chair (Optima) as per details below- Type of backrest support backrest with lumber support of polypropylene at multilevel across back & Ergonomic Seat Design, Backrest is made of two pcs injection moulded frame Overall Chair Height 1125 mm, Backrest Height Plus Minus 15mm 600 millimeter, Backrest Width 480 millimeter, Seat Height 520 mm, Seat Width 500 mm, Thickness of MS Plate Joining the under structure with Seat 0.5 millimeter, Wheel base made of MS covered with chrome polish, Thickness of Plywood used in Seat Plus Minus 1(mm) 12 mm, Colour - Black or as per requirement seat material PU Foam covered with Fabric or leatherite Arm Material - Propylene Warranty - 02 Years, Modular cabinet type side unit (Close Type) Length of Table - 1500mm (Plus Minus 15mm), Width - 450mm (Plus Minus 10mm), Height - 750mm (Plus Minus 10mm) Type of frame - Internal frame of 18mm thick prelaminated particle board added to 18mm thick external frame, Table Top Finish - Laminate in color with matt finish 0.6-0.8mm thickness of type S, F or P having index no.3.2.3 conforming to IS 2046/Latest with having balancing laminate of 0.5mm thick on another side. Door Shutters - Yes (made up of prelaminated particle board), No. of Drawers - 03 Nos Drawers with 03 Nos Swing drawers, Locking arrangement - Yes, Top of table - 25mm thick post forming, Type of finish - laminated in required colour, Warranty- 02 Years, SOFA- Two Seater Seating Capacity- 2 Seater Sofa Frame Covering - Fully Upholstered Covering Material for Seat and Backrest - Fabric Frame Structure Material and size (Plus Minus 1 mm) - Wooden frame structure Frame Structure Material and size (Plus Minus 1 mm) any other wood of minimum 19 mm thickness. Seat Cusion Material - foam Length of Two Seater Units in mm (Plus Minus 10 mm) 1500 Depth of Sofa Units in mm (Plus Minus 10 mm) 700 Density of Cushion of Backrest Material (Kg/Cubic M) 40 Sofa Height (Without Back Cushion) Plus Minus 5 (mm) 700 millimeter Sofa Height (With Back Cushion) Plus Minus 5 mm 800 millimeter Thickness of Foam in arms Plus Minus 2 (mm) 50 Colour of Polish on exposed Wood frame wood colour Springs shall be of best quality and indian make and of size 6 Inch/7 Inch as required and minimum 12 nos per seat of sofa. Cloth shall be provided as approved by Enginee-in-Charge & shall be minimum Rs. 600 per meter if differs amount will be deducted as difference of rate with addition of 50% Contractor profit. Bottom portion of sofa will be sealed with markeen etc as directed by Engineer-In-Charge. All other material like jute/rubberpad etc. if and as required shall be of best quality. WARRANTY PERIOD IN NUMBER OF YEARS- 03 Years, Providing & Placing SOFA- Single Seater as per details below- Seating Capacity- 1 Seater Sofa Frame Covering - Fully Upholstered Covering Material for Seat and Backrest - Fabric Frame Structure Material and size (Plus Minus 1 mm) - Solid Seasoined Teak Wood frame structure of minimum 35mm thickness Seat Cusion Material - foam Length of Single Seater Units in mm (Plus Minus 5 mm) 850 Depth of Sofa Units in mm (Plus Minus 10 mm) 850 Density of Cushion of Backrest Material (Kg/Cubic M) 40 Length of Single Seater Units in mm (Plus Minus 25 mm) -850 Sofa Height (Without Back Cushion) Plus Minus 25 (mm) 800 millimeter Sofa Height (With Back Cushion) Plus Minus 5 mm 800 millimeter Thickness of Foam in arms Plus Minus 2 (mm) 50 Design - as per choice / architectural drawings, Colour of Polish - as per choice Springs shall be of best quality and indian make and of size 6 Inch/7 Inch as required and minimum 10 to 12 nos per seat of sofa. Cloth shall be provided as approved by Enginee-in-Charge & shall be minimum Rs. 1750 per meter if differs amount will be deducted as difference of rate with addition of 50% Contractor profit. Bottom portion of sofa will be sealed with markeen etc as directed by Engineer-In-Charge. All other material like jute/rubberpad etc. if and as required shall be of best quality. WARRANTY PERIOD IN NUMBER OF YEARS- 03 Years, Providing & Placing Wooden Center Table 1000x650mm with glass top as per details below- Length of Table 1000mm (Plus Minus 20mm), Width 650mm (Plus Minus 15mm), Height 460mm (Plus Minus 15mm) Type of frame- Wooden No. of Legs- 04 Nos of size 45mmx45mm Table should be polished as per required shade. Glass top should be of superior quality and required shade having thickness 10mm (+0.5mm) Warranty- 02 Years, Providing Wooden Almirah as per details below- Width - 1200mm (Plus Minus 10mm), Depth - 450mm (Plus Minus 10mm), Height - 1800mm (Plus Minus 15mm), No. of shelves - 05 Nos, No. of Door Shutters - 02 nos, No. of Cabinet Compartments - 02 Nos (Upper cabinet door shutters with glazed panelling and lower cabinet fully covered wooden door shutters) Thickness of material 18mm thick (Plus Minus 1 mm), Type of Veneer - Teak Wood, Locking arrangment - Yes, Colour and Polishing - as per requirement, Warranty- 02 Years, Providing Wooden Almirah as per details below- Width - 900mm (Plus Minus 10mm), Depth - 450mm (Plus Minus 10mm), Height - 1800mm (Plus Minus 15mm), No. of shelves - 05 Nos, No. of Door Shutters - 02 nos, No. of Cabinet Compartments - 02 Nos (Upper cabinet door shutters with glazed panelling and lower cabinet fully covered wooden door shutters) Thickness of material 18mm thick (Plus Minus 1 mm), Type of Veneer - Teak Wood, Locking arrangment - Yes, Colour and Polishing - as per requirement, Warranty- 02 Years, Providing & Placing Wooden Center Table 1200x600mm with glass top Length of Table 1200mm (Plus Minus 20mm), Width 600mm (Plus Minus 15mm), Height 460mm (Plus Minus 15mm) Type of frame- Wooden No. of Legs- 04 Nos of size 45mmx45mm Table should be polished as per required shade. Glass top should be of superior quality and required shade having thickness 10mm (+0.5mm) Warranty- 02 Years, Providing & Placing Wooden Podium as per details below- Podium top material- 18mm three layer prelaminated particle board, Length of Podium - 600 to 650mm, Depth of Podium - 50 to 525mm, Height of Podium - 1100 to 1200mm, Top position fixed, Type of finish - laminated in required colour, Warranty- 02 Years