Bandipora Tenders

CATEGORY: Dismantling of old worn out Wall paneling with frame structure of Transmitter Hall and Technical area, shifting and disposal of dismantled debris material from the outside of the office premises , Wall paneling treatment in Transmitter Hall and Technical area , Providing, fabrication and fixing of cedar or teak wooden skirting 125mm x 15mm in Transmitter Hall and Technical area , Providing, fabrication and fixing of cedar or teak wooden planks 75mm x 15mm in Transmitter Hall and Technical area , Dismantling of old worn out false ceiling material with frame structure of transmitter hall and technical area, shifting and disposal of debris material from the outside of the office premises. , Providing, fabrication and fixing of false ceiling in Transmitter Hall and Technical area at HPT TV site Gurez as per drawings and respective layout drawings. , Providing of 600mm x 600mm hinged flap flushed doors and fixing it on the ceiling as per requirement of site at Gurez , Providing, fabrication, fixing and polishing of wooden table for emergency studio with console table top 25mm thick wooden board or commercial ply with Sunmica sheet 1mm thick , Providing, fabrication, fixing and polishing of heavy duty wooden workshop table with top made up of 25mm thick wood plank on top and wooden batten frame with wooden beading and moulding , Providing and applying of wall finish, putty and POP on walls to make smooth finish for premium emulsion paint at Transmitter Hall and Technical area, after touching on corners etc , Providing and applying two coats of wall primer on gypsum false ceiling and walls etc transmitter hall and technical area, after touching on corners, joints and screw heads etc as required , Providing and applying two to three coats of water based luxury emulsion on gypsum false ceiling and walls surface , Wooden surface to be cleaned and wooden putty to be applied and after rubbing with appropriate sand paper to smooth the surface two or more coat of wooden polish to be applied in wainscot and doors , Providing and applying of 50mm x 50mm x 12mm wooden cornice as per approved profile at all around false ceiling in transmitter hall and technical area , Fixing with complete wiring of 2ft x 2ft recessed mounted LED lights , Fixing with complete wiring of 1ft x 1ft recessed mounted LED lights

CATEGORY: 3 Part Automated Hematology Analyzer (V2) (Q2)

BOQ ITEMS: DENSIMETER NO/NC 0.75MPA(ABS) GL316 1A2L , PRESSURE GAUGE -1 TO 9 BAR , SF6 GAS CYLINDER - 25 KG (AS PER IEC 60376), JOINT TORIQUE R12, BAGUE R21 NT1932 S667, JOINT TORIQUE R22 A29.3 D3.6, BAGUE R9 M146, RI 12.37 x 2.62 EPDM -50, O-RING D 31.4 D 0.62, O-RING D 23.4 D 3.53, BAGUE R82 NT1932 S667, SECURITY COVER GASKET, JOINT ISOLATEUR D316( for 245KV and above chamber insulator gasket), INSUALTOR GASKET D226(suppot insulators for 245KV and above), Trip/Close Coil, 220V DC, Trip Magnet Assy FK3-1 , Close Magnet Assy FK3-1 , Aux Contact Assy 16 NO+16 NC, Motor Limit Switch (4NO+ 4NC), Plastic Gear Assy With Bearings, Spring Charging Motor 220 VAC/DC, OPERATION COUNTER, Dashpot Assembly FK3-1CK, View Glass with Beading, Sealing Ring (Rain Sheild), Crank Wheel Assy FK 3-1 CK, Roller Lever Assy for FK 3-1 CK, Trip latch stage 1 with spring/FK3-1 CK, Trip Latch Assy Stage 2 for FK 3-1 CK, Close Latch for FK3-1 CK, Freewheel assembly with Bearing FK3-1CK, NRB Assy for FK3-1 CK, Manual Charging Gear Assy FK3-1CK, LOC-OFF-REM SWITCH LOCKABLE, AC CONTACTOR 230V 2NO+2NC, ADD ON BLOCK 1NO+1NC, DC CONTROL SWITCH, POLE DISCREPANCY RELAY- VTT11 , SIEMENS TIMER 0.05 to 100hrs -24 v 240 AC/DC, POLE/DISCREPANCY TIMER 3RP15 25-1BW30 8K, PUSH BUTTON (1 FULL SET), DC MCB 6A DP, Reinforced Rubber Beading for LCC(1CB 10 MTR), CONSUMABLE KIT, Each Kit Contains Molykote 111 (100 grams), Loctite 8103 (25grams) Molykote PG54 (25grams) Contactal Grease, Loctite 243 Thread Removable Locker (25ml) Loctite 262 Thread, mobilex bt3 (100grams) permanent Locker (25ml),, GLATTOL 4130 982 (Shell Alvania (200 Gm))

CATEGORY: Battery Charger 72 Volt ELAK , Soldering Iron 250 Watt , Soldering Iron 35 Watt , Wire Cutting Plier , Multi Meter , Round File 8 Inch , Small Socket Set , Oil filter Remover Spanner TATA 407 , Oil filter Remover Spanner TATA Sumo , Oil filter Remover Spanner TATA 1212 TC , Oil filter Remover Spanner Swaraj Mazda , Oil filter Remover Spanner TATA 1512 TC , Oil filter Remover Spanner TATA 1613 TC , TATA 407 Front AND Rear Check Nut Puller , TATA 407 Brake Adjuster Tools , Pipe Wrench 6 Inch , Medium Piston Ring Compressor New Type , Heavy Piston Ring Compressor New Type , Socket Set 8 to 32 , Bolero Front Wheel Check Nut Puller , Welding Cable Single Phase , Ball Chisel , Welding Cable Three Phase , Holder Heavy Duty , Chisel Assorted Size Set of 3 Pcs , Ball pin Hammer 100 Gm , Impact Screw Driver Set , Adjustable iron hand plane Anant 15 Inch , Hand Saw , Mortise Chisel Set of 5 Pcs , Hammer Drill Machine , Screw Driver Two in One 12 Inch , Measuring Tape , Hammer 200 Gm , File Flat 12 inch

C/o Tile Path From Ad Rashid Mir Onwards