Valve Tenders

Details: Description Specifications For Motor Vehicle - Pick - Up Body Type: Pick-up Truck No. Seats: 5 Fuel Type: Diesel Emission Standard: Euro 4 Fuel Capacity: 76l Transmission: Manual Max Output: (hp) 114 @3,600 Rpm - 140 Hp @ 3,600 Rpm Drive Train: Rear Wheel Drive Wheel Size: 16 Airbags: 1 Entertainment System: 2din Radio Connectivity: Am, Fm, Usb Engine Size: 2.8l Displacement: 2.798cc Number Of Cylinders: 4 Number Of Valves: 16 Auto Brake System Electronic Brake Distribution Electronic Door Locks Power Steering Power Windows Accessories: Emergency Light With Public Address System Lgu Decal Sticker

Details: (1) Bhusawal (drh): - Improvement To Doctor's Rooms, Officer's Special Ward, Chi Office, Opd Area, Various Wards, Front Facade, Medicine Room, Kitchen, Circulating Area & Parking Facilities, Drainage Arrangements Etc. In Divisional Railway Hospital At Bhusawal. (id No.01.01.64.23.1.50.003) (2)bhusawal(drh):- Improvement In Operation Theatres Of Divisional Railway Hospital Bhusawal. (rev-2024-25) (3)bhusawal(fp)- Repairs To Jack Well No.3 Along With Pipe Staging And Sluice Valves At Tapti Pump House.(rev-2024-25) (4) Bhusawal(fp)- Repairs To Road From Wssc School To Tapti Pump House And Back Side Road Of Wssc And Railway School. (rev-24-25)

Details: for Augmentation of water Supply Scheme Mohlowali & Malukwali Bif. Existing W/S Scheme Shahpur Jajjan Block Dera Baba Nanak, Distt. Gurdaspur, Under Head B.A.D.P.Supplying and laying of uPVC pipes 10kg cm2, valves and houdies, Development of water works Distribution System 6kg cm2, Dismantling and Removing of leakages, Providing & Installing Water connection and Carriage of Materials & Enviornment complete in all respects. Operation & Maintenance Cost excluding Electricity Charges) Operation and Maintenance water supply system for 3 Months including operating of machinery , repair of leakages, supplying of full time Pump Operator cum- Chowkidar, supply of Sodium Hypo Chlorite solution for disinfection for 3 months after completion.

Details: Description 1 Lot Repair Of Aircon Of Toyota Avanza P5-v610 Scope Of Work: * Pull-down Evaporator For General Cleaning And Leak Test * Add Capilla Oil * Vacuum Of Lines * Recharge Freon Gas R134a * Pull-down Condenser * Flushing Of System * Replace Expansion Valves Front And Rear * Replace Filter Drier * Replace Cabin Filter * Replace Cooling Coil Original * Replace Compressor – Original Toyota X-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x Please Email This Form To: Bbs_propertyprocurement@yahoo.com Or Fax To (02)8920-4353

Description: Public tender Vob/a Redesign of the Kallental sewage treatment plant and supply line to the Marsberg-Mitte sewage treatment plant. Structural part sewerage system approx. 25 m DN 150: PP-MD sewer approx. 195 m DN 200: PP-MD sewer approx. 11 m DN 200: PEHD sewer approx. 2 m DN 300: PP-MD sewer approx. 90 m DN 600: SB sewer approx. 13 ... More. Construction part Sewerage Approx. 25 M DN 150: PP-MD sewer Approx. 195 M DN 200: PP-MD sewer Approx. 11 M DN 200: PEHD sewer Approx. 2 M DN 300: PP-MD sewer Approx. 90 M DN 600: SB sewer Approx. 13 M DN 600: PEHD sewer Approx. 6 shaft structures, DN 1000 Approx. 2 shaft structures, DN 1200 Approx. 1 plug-in gate, DN 200 Approx. 1 plug-in gate, DN 600 Approx. 1 spindle gate, DN 600 Water pipe Approx. 10 M DN 50: PEHD pipe Approx. 40 M DN 80: PEHD pipe Fittings: Approx. 2 pieces Underground hydrant, Dn 80 Approx. 1 Kos slide valve, Dn 80 Cable conduits Approx. 195 M Dn 100: PEHD pipes Construction of the building including earthworks 1 rain overflow basin, round basin, V=460 M³, prefabricated construction 1 measuring/throttle shaft, prefabricated construction, Lxwxh = 4.25x2.00x2.35 M Il 1 bedload station/debris trap, prefabricated construction, Lxwxh = 2.70x1.80x2.50 M Il 1 rain retention basin construction in earthworks (in existing sewage pond) Conversion work on existing building Basin overflow: - Removal of old equipment Sand and floating material trap: - Removal of old equipment - Installation of filling concrete and manufacture of clinker channel Operating/screening building - Removal of door and installation of roller shutter system - Adjustments to floor coverings after screen installation Surface work Approx. 45 m³ topsoil supply Approx. 75 m³ frost protection material/fss Approx. 260 m³ water-bound surface incl. fss Approx. 105 m² paving 10/20/10 cm Approx. 155 m deep curbstones 8/25/100 cm Approx. 50 m deep curbstones 10/30/100 cm

Details: Description Republic Of The Philippines Region Xii Province Of Cotabato Municipal Government Of Antipas Request For Quotation The Municipal Government Of Antipas, Through Its Bids And Awards Committee (bac), Hereby Invites Interested Suppliers To Submit Price Quotation For Various Purchases Use For Diff. Vehicles With The Following Items With Abc Of P 83,670.00. Item No. Quantity Unit Description 1 1 Pc Clutch Disc 2 1 Pc Release Bearing 3 2 Pc Accelerator Cable W/installation 4 1 Pc Overhauling Gasket 5 1 Pc Piston Ring Std 6 5 Pc Sand Paper 7 6 Gal Oil-15w40 8 1 Set Grinding Compound 9 1 Pc Gasket 10 4 Pc Oring 11 1 Pc Camshaft Sensor 12 1 Pc Oil Seal 9123-gb5-726 13 1 Pc Oil Pan Gasket 14 1 Pc Timing Belt 15 1 Pc Vellumoid Gasket 16 2 Pc Brake Cleaner 17 1 Pc Carb Cleaner 18 1 Pc Circlip 19 6 Pc Nut And Washer 20 2 Gal Coolant 21 2 Pc Radiator Cap 22 2 Pc Thermostat 23 1 Pc Headlight Bulb 24 1 Pc Tail Light Bulb 25 1 Pc Wheel Align 26 2 Set Oil Seal 90311-45028 27 1 Pc Gasket 28 2 Pcs Suspension Arm 29 1 Set Tie Rod End 30 3 Pc Oring 31 1 Pc Oil Filter 32 1 Pc Parts Cleaner 33 2 Ft Vellumoid Gasket 34 1 Set Crankshaft Assy 35 1 Pc Gauge 36 1 Pc Main Bearing Std 37 1 Pc Trust Washer Std 38 1 Set Con Rod 39 1 Pc Con Rod Bearing Std 40 1 Set Piston Ring Std 41 1 Pc Crankshaft Oil Seal 42 3 Set Cement Gasket 43 1 Set Valve Seal 44 2 Pcs Oil Seal 45 1 Pc Cylinder Head Gasket 46 1 Pc Power Spray 47 1 Pc Oil Filter 48 1 Pc Pvc Valve 49 2 Pc Thermocap 50 2 Pc Exhaust Manifold Request For Quotation Form Can Be Obtained From Gso, Municipal Hall, Antipas, Cotabato On February 4-7, 2025 And The Deadline For Submission Of Sealed Quotation Is On February 7, 2025 At 9:00 A.m. Opening Of Sealed Quotation Is On February 7, 2025 A.m. At Mpdo, Antipas, Cotabato. Interested Suppliers Should Submit Their Sealed Quotations To The Bac Chairman, Lgu-antipas, Cotabato. Suppliers Are Required To Submit The Following: A) Valid Business Permit B) Philgeps Registration Certificate/number C) Omnibus Sworn Statement The Municipal Government Of Antipas Reserves The Right To Accept Or Reject Any Quotations, To Annul The Request For Quotation Process, And To Reject All Quotations At Any Time Prior To Contract Award, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. Noemi S. Reyes Bac Chairman

Description: Public tender (delivery service) Delivery of a mobile excavator for municipal use 1 Brief description of the service The municipality of Wehrheim intends to purchase a mobile excavator for the municipal depot. 2 Intended use The conditions of use are predominantly in the area of water supply, particularly for civil engineering work, pipe bursts and the replacement of valves and hydrants to maintain a functioning drinking water supply. The excavator is also used to prepare for heavy rain. This includes the maintenance and restoration of existing ditches and streams, including the clearing of washed-up rubbish after heavy rain. 3 General requirements 3.1 Offer documents The following documents must be enclosed with the offer for the products offered: - Brochure material - Data sheet / dimension sheet of the vehicle 3.2 Acceptance The acceptance of the vehicle and the superstructures and attachments takes place by the client at the following location: Municipality of Wehrheim, Zur Burg 32, 61273 Wehrheim, construction yard The costs of transporting the vehicle to the above location must be included in the final offer price. 3.3 Instruction When the vehicle is handed over, the contractor carries out an instruction at the delivery location Municipality of Wehrheim, Zur Burg 32, 61273 Wehrheim, construction yard. This is part of the scope of services.

Details: Description Item No. Unit Item Description Qty. Unit Cost Total Cost 1 Lot Complete Supply Of Labor, Tools And Equipment For The Pneumatic Testing Of Fire Sprinkler System Of Valenzuela Medical Center - Ids Building Scope Of Works: A.) Precautions: - Pneumatic Testing Involves The Hazard Of Released Energy Stored In Compressed Gas In The Event Of A Breach Of Containment. - Care Must Be Taken To Minimize The Chance Of Brittle Fracture During The Pneumatic Leak Test. Test Temperature Is Important In This Regard, As Low Temperatures Can Increase The Chance Brittle Fracture, And Must Be Considered When The Designer Chooses The Material For Construction. - Parts Of Mechanically Assembled Systems Must Not Be Adjusted While The System If Under Pressure. - Adequate Anchoring Shall Be Provided For Equipment To Be Tested. - Calibrated Pressure Gauges Shall Be Used During The Test. - Valves Shall Be Used To Isolate The System Equipment From The Pressure Source. B.) Testing Manifold And Pressure Relief Device (prd): - Any Supplementary Valves, Piping, Hoses, Etc. Required For The Test Shall Be Inspected And Accepted By The Valenzuela Medical Center Personnel. - A Prd Shall Be Provided. - The Set Point Of The Prd Shall Not Be Greater Than The Test Pressure, Plus The Lesser Of 345 Kpa (50psi) Or 10% Of The Test Pressure. C.) Test Fluid: - If Not Air, The Gas Shall Be Nonflammable And Nontoxic. D.) Test Pressure: - The Test Pressure Shall Be In Accordance With The Code Of Construction (usually 110% Of The Design Pressure) E.) Preparation: - The Safe Distance, As Identified In The Test Procedure, Shall Be Identified By Placing Appropriate Barriers. - All Staff Associated With Or Conducting A Pneumatic Pressure Test Shall Be Deemed Competent By The Organization Conducting The Test. - Removal Of Existing Fire Sprinkler Heads - A Pre-test Safety Meeting Should Be Conducted To Ensure All Personnel Present On The Site That May Be Exposed Are Aware Of The Hazards, Mitigations, And Emergency Response Plan. - All Visual Inspections And Non-destructive Examinations Required By The Code Of Construction Shall Be Completed And Evaluated As Acceptable. - A Pre-test Inspection Shall Be Made To All Connections To Verify Proper Assembly And Tightness, Positioning Of Valves, Overpressure Protection, And Control Of Test Medium. F.) Pressurization Procedure: - The Test Pressure Shall Be Gradually Increased Until The Pressure Reaches The Lesser Of 170kpa (25psi), Or 1/2 Of The Test Pressure. At This Time A Preliminary Check Shall Be Made. If Leaks Are Identified, Then The System Shall Be De-pressured And Repairs Made To Correct The Deficiency Prior To Proceeding. - Thereafter, The Pressure Shall Be Gradually Increased In Steps Until The Test Pressure Is Reached (i.e 25% 50%, 75% Of Mawp, Followed By Test Pressure). The Pressure Shall Be Held At Each Step Long Enough To Equalize The Piping Strains. The Safe Distance Identified In The Procedure Must Be Observed During This 'portion Of The Test. If Leaks Are Identified, The System Shall Be De-pressured And Repairs Made Prior To Proceeding Re-pressurization Must Follow All Of The Above Steps. - The Test Pressure Shall Then Be Reduced To The Design Pressure Before Examining For Leakage. G.) Installation Of Existing Fire Sprinkler Heads - After The Pneumatic Testing Conducted And Verify That The System Has No Leak, The Existing Fire Sprinkler Head Should Be Installed. H.) Testing And Commissioning - Conduct Testing And Commissioning I.) Removal Of Testing Manifold: - Any Supplementary Valves, Piping, Hoses, Etc. Required For The Test Shall Be Removed After Testing Is Complete. J.) Duration Of Work: 7 Days K.) Warranty: Three (3) Months On Supplies And Labor 1 177,883.33 177,883.33 Grand Total 177,883.33

Details: Description Republic Of The Philippines Region Xii Province Of Cotabato Municipal Government Of Antipas Request For Quotation The Municipal Government Of Antipas, Through Its Bids And Awards Committee (bac), Hereby Invites Interested Suppliers To Submit Price Quotation For Various Purchases Use For Diff. Vehicles With The Following Items With Abc Of P 83,670.00. Item No. Quantity Unit Description 1 1 Pc Clutch Disc 2 1 Pc Release Bearing 3 2 Pc Accelerator Cable W/installation 4 1 Pc Overhauling Gasket 5 1 Pc Piston Ring Std 6 5 Pc Sand Paper 7 6 Gal Oil-15w40 8 1 Set Grinding Compound 9 1 Pc Gasket 10 4 Pc Oring 11 1 Pc Camshaft Sensor 12 1 Pc Oil Seal 9123-gb5-726 13 1 Pc Oil Pan Gasket 14 1 Pc Timing Belt 15 1 Pc Vellumoid Gasket 16 2 Pc Brake Cleaner 17 1 Pc Carb Cleaner 18 1 Pc Circlip 19 6 Pc Nut And Washer 20 2 Gal Coolant 21 2 Pc Radiator Cap 22 2 Pc Thermostat 23 1 Pc Headlight Bulb 24 1 Pc Tail Light Bulb 25 1 Pc Wheel Align 26 2 Set Oil Seal 90311-45028 27 1 Pc Gasket 28 2 Pcs Suspension Arm 29 1 Set Tie Rod End 30 3 Pc Oring 31 1 Pc Oil Filter 32 1 Pc Parts Cleaner 33 2 Ft Vellumoid Gasket 34 1 Set Crankshaft Assy 35 1 Pc Gauge 36 1 Pc Main Bearing Std 37 1 Pc Trust Washer Std 38 1 Set Con Rod 39 1 Pc Con Rod Bearing Std 40 1 Set Piston Ring Std 41 1 Pc Crankshaft Oil Seal 42 3 Set Cement Gasket 43 1 Set Valve Seal 44 2 Pcs Oil Seal 45 1 Pc Cylinder Head Gasket 46 1 Pc Power Spray 47 1 Pc Oil Filter 48 1 Pc Pvc Valve 49 2 Pc Thermocap 50 2 Pc Exhaust Manifold Request For Quotation Form Can Be Obtained From Gso, Municipal Hall, Antipas, Cotabato On February 5-10, 2025 And The Deadline For Submission Of Sealed Quotation Is On February 10, 2025 At 9:00 A.m. Opening Of Sealed Quotation Is On February 10, 2025 A.m. At Mpdo, Antipas, Cotabato. Interested Suppliers Should Submit Their Sealed Quotations To The Bac Chairman, Lgu-antipas, Cotabato. Suppliers Are Required To Submit The Following: A) Valid Business Permit B) Philgeps Registration Certificate/number C) Omnibus Sworn Statement The Municipal Government Of Antipas Reserves The Right To Accept Or Reject Any Quotations, To Annul The Request For Quotation Process, And To Reject All Quotations At Any Time Prior To Contract Award, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. Noemi S. Reyes Bac Chairman

Details: Description Republic Of The Philippines Province Of Batanes Municipality Of Mahatao Mahatao, Batanes Bids And Awards Committee Invitation To Apply For Eligibility And To Bid The Municipal Government Of Mahatao Through The General Funds Intends To Apply The Sum Of Php 220,000.00 Being The Approved Budget For The Contract (abc) To Payments Under The Contract For The Procurement Of Supplies For The Improvement Of Tourist Sites & Facilities. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. Description Of Items Item No. Item Description Qty Unit 1 Portland Cement 35 Bags 2 10mm Dia X 9m Reinforced Steel Bars 15 Pcs 3 Tie Wire 8 Kgs 4 ½” Ordinary Plywood 2 Pcs 5 2”x4”x12’ Rough Lumber 6 Pcs 6 2”x3”x12’ Rough Lumber 4 Pcs 7 Cwn, 3” 10 Kgs 8 G.i. Top Flashing 1 Pc 9 Thermoplastic Roofing, Corrugated, 6ft, 2.0mm Thick 8 Pcs 10 Tekscrew, 2 ½” 100 Pcs 11 Rubber Washer 100 Pcs 12 700 X 2100m Panel Door With Jamb 2 Sets 13 600x2100m Panel Door With Jamb 1 Set 14 Jalousie Window, W600mmx H500mm, Smoke Glass 3 Sets 15 Glass Blocks, 150mm X 150mm Smoke 8 Pcs 16 300mm X 300mm Homogenous Floor Tiles, Nonskid, Design And Color For Approval 50 Pcs 17 300mm X 600mm Homogenous Wall Tiles, Design Pattern And Color For Approval 125 Pcs 18 Tile Adhesive, Abc 10 Bags 19 Water Closet, 2 Piece, Dual Flush Type, Water Saver Complete With Fittings & Accessories, For Approval Po221/hcg White 3 Sets 20 Water Closet, -seat Cover, Verify Model White 3 Sets 21 Lavatory, Counter Top, Wash Basin Complete With Fittings & Accessories, For Approval White 1 Pc 22 Urinal, Wall Hung, Complete With Fittings & Accessories For Approval 1 Pc 23 304 Stainless Steel Single Cold Shower Set, Wall-mounted, See Attached Photo 3 Pcs 24 Single Lever Lavatory Faucet, 304 Stainless Steel, Heavy Duty, 12”, For Countertop Type Lavatory, See Attached Photo 7 Pcs 25 Hand Bidet, 304 Stainless Steel 7 Pcs 26 Single Bowl Kitchen Sink, 304 Stainless Steel, Complete With Fittings & Accessories 2 Pcs 27 Flexible Hose Connector, ¾” X ½” 8 Pcs 28 Flexible Hose Connector, ½” X ½” 7 Pcs 29 Pvc Gate Valve ½” 5 Pcs 30 Double Angle Valve, ½”x ½” Ss 7 Pcs 31 Single Angle Valve, ½” Ss 8 Pcs 32 Bottle Trap For Lavatory, Ss 7 Pcs 33 Floor Drain, 4” X 4” Stainless Steel 2 Pcs 34 Teflon Tape 5 Pcs 35 Neltex Solvent, 100cc 3 Cans 36 Pvc Fittings Wye 45, 3” 3 Pcs 37 Pvc Fittings Clean Out, 3” 3 Pcs 38 Pvc Fittings Wye 45, 2” 4 Pcs 39 Pvc Fittings Elbow, 2” 2 Pcs 40 The Municipal Government Of Mahatao Now Invites Bids For The Procurement Of Supplies For The Improvement Of Tourist Sites & Facilities. Completion Of The Works Is 60 Calendar Days Upon Receipt Of Notice To Proceed. Bidders Should Have Completed, Within One (1) Year From The Date Of Submission And Receipt Of Bids, A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii. Instruction To Bidders. Interested Bidders May Obtain Further Information From The Municipal Local Government Of Mahatao And Inspect The Bidding Documents At The Address Below During 8:00 Am - 12:00 Nn And 1:00 Pm – 5:00 Pm, Monday To Friday. A Complete Set Of Bidding Documents May Be Purchased By The Interested Bidders At The Bac Secretariat Office, Municipality Of Mahatao, Province Of Batanes, Starting On January 9-22, 2025 Upon Payment Of Non-refundable Fee Of Php 500.00 For Each Set. Bids Must Be Duly Received By The Bac Secretariat At The Address Below On Or Before January 23, 2025, 10:00 A.m. At The Bac Office, Mahatao, Batanes. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 18. Bid Opening Shall Be On January 23, 2025, 2:00 P.m. At The Municipal Training Hall. Bids Will Be Opened In The Presence Of The Bidder’s Representatives Who Choose To Attend At The Address Below. Late Bids Shall Not Be Accepted. The Lgu Bac Of Mahatao, Batanes Reserves The Right To Accept And Reject Any Bid, Declare The Whole Bidding Process Null And Void Any Time Prior To The Awarding Of Contract Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. For Further Information, Please Refer To: Rechie G. Rareza Head – Bac Secretariat Municipality Of Mahatao Province Of Batanes Email Address: Lgumahatao.bac@gmail.com Deborah C. Villamor Bac Chairperson