Mask Tenders

Details: Description 1. The Department Of Education – Division Of Tangub City, Through The General Appropriations Act 2024 Intends To Apply The Sum Of Three Million Nine Hundred Seventy-eight Thousand One Hundred Six Pesos (php 3,978,106.00) Being The Approved Budget For The Contract (abc) To Payments Under The Contract For Second Procurement Of Learning Tools And Equipment For Technical Vocational Livelihood To Deped-public Schools With Identification Number Tvl - 2025 – Rx – Tangub City – 030.a. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. Quantity Unit Item Description Abc Lot 1. Lorenzo Tan National High School (caregiving Nc Ii)- Php 400,403.00 5 Piece Airpot 1.type: Water Heater 2. Outer Material: Hard Plastic, (pp) Polypropylene, Heat Resistant 3.cavity Material: Stainless Steel 4. Capacity: 2.5 Liters 5.voltage: 220/240/volts 6.ac 50/60 Hz. Power In Watts: 500 To 800 Watts 7.comes With English Manual That Contains: Users Guide, List Of Parts, Maintenance Guide, Safety Guide 8. The Item Must Be Branded And Good Quality. 10 Piece Apron 1.type: Bib Apron 2. Material: Polyester-cotton Fabric 3.length: 20 To 40 Inches (minimum) 4. With 2 To 3 Bottom Pockets; 5.color: Any 6.the Item Must Be Of Good Quality 2 Piece Bath Tub, Baby 1. Material: Hard/sturdy Plastic, (pp) Polypropylene 2. Color: Any 3.dimension: (l X W X H) 670 To 700 Mm X 400 To 420 Mm X 160 To 190 Mm (minimum) 4. Thickness: 3 Mm To 6 Mm (minimum) 5.color: The Item Must Be Of Good Quality 10 Piece Baby Blanket 1. Type: Blanket 2. Material: 100% Cotton 3.color: White 4. Dimension: (l Xw) 38 To 42 Inches X 28 To 32 Inches (minimum) 5. Washable 6. The Item Must Be Of Good Quality 20 Piece Basin (small) 1.material: Hard Plastic, (pp) Polypropylene 2. Color: Any 3.dimension: 280 - 320 Mm Diameter X 80 - 120 Mm Higher (mimimum) 4. Thickness: 2 Mm To 4 Mm (minimum) 5. The Item Must Be Of Good Quality 20 Piece Bath-towel, Towellete 1. Type: Bath Towel 2. Material: 100% Cotton 3.color: White 4. Dimension: ( L X W ) 120 - 125 Cm X 60 - 65 Cm (minimum) 5.washable 6.the Item Must Be Of Good Quality 5 Piece Bedpan 1.material: Hard Plastic, (ps) Polystyrene 2. Color: Any Color 3.dimension: ( L X W X H) 22 - 26 Cm X 27 - 32 Cm X 7 - 12 Cm (minimum) Approximate 4. Capacity: 1 Liter (minimum) 5.thickness: 2 To 5 Mm 6.saddle-shaped And Lightweight 7. The Item Must Be Of Good Quality 10 Piece Blanket 1. Type: Blanket 2. Material: Cotton 3.color: White 4. Dimension: (l X W) 80 - 90 Inches X 54 -64 Inches Approximate 5. Washable 6. The Item Must Be Of Good Quality 3 Piece Bottle Sterilizer, Electric 1. Type: Electric Steam Sterilizer 2. Material: Hard Plastic (p E) Polyethylene Or Its Equavalent 3.color: Any Color 4. Capacity: 6 Bottles (minimum) 5.sterilizes Bottle And Accessories By Steam 6. With Automatic Power Shut-off Function 7. Dimensions: 8. Power Supply: 220 V-240v Ac, 50/60 Hz. 9. The Item Must Be Of Good Quality 5 Piece Bread Toaster 1. Type: Electric Bread Toaster 2. Dimensions ( W X D X H): 25 - 30 Cm X 15 -20 Cm X 18 - 22 Cm (minimum) Approximate 3. Capacity: 2 Slices 4. Power Supply: 220v-240v Ac, 50/60 Hz. 5. 400 To 600 W (minimum) 6. The Item Must Be Of Good Quality 10 Piece Burping Cloth 1. Type: Burping Cloth 2. Material: 100% Cotton 3. Color: Any Color 4. Dimension: Length: 17 -19 Cm Width: 14 -16 Cm (minimum) 5.washable 6. The Item Must Be Of Good Quality 10 Piece Cane 1.type: Adjustable Offset-walking Cane 2. Material: Aluminum 3.tip Size: 18 4. Height Adjustment: 31 Inches To 39 Inches (with 1 Inch. Increment) 5.weight Capacity: 200 - 250 Lbs. (minimum) 6.with Rubber Handle; With Push-botton Height Adjustment 7. The Item Must Be Of Good Quality 5 Piece Carpet 4ft. X 8 Ft 1.material: Polyster 2. Color: Any Patterned Color 3.dimension:48 Inches X 96 Inches (minimum) 4.the Item Must Be Of Good Quality 5 Set China Ware 1.material: Porcelain 2. Fit To Be Used In Ovens And Microwaves 3.specific Dimensions: Dinner Plate Diameter: 10 Inches (minimum) 4. Salad Plate Diameter: 7 Inches (minimum) 5.bowl Diameter: 5 Inches (minimum) 6.mug: 12 Oz. (minimum) 7. The Item Must Be Of Good Quality 8. Set Includes: 1 Piece Dinner Plate, 1 Set Salad Plate, 1 Piece Bowl, 1 Piece Mug 10 Piece Clothes Brush 1. Type: Rectangular Clothes Brush 2. Handle Material: Wood 3. Bristle Material: Plastic Bristle 4. Color: Any Color 5.overall Dimension: ( L X W X H) 140 -160 Mm X 45- 60 Mm X 20 -30 Mm (minimum) 6. The Item Must Be Of Good Quality 10 Piece Clothes Hamper 1. Type: Square Hamper 2. Material: Polyester 3. Color: Any Color 5. Dimension: ( L X W X H) 32 To 34 Cm X 36 To 38 Cm X 56 To 58 Cm (minimum) 5. The Item Must Be Of Good Quality 2 Piece Clothes Rack 1.type: Single-pole Clothes Rack 2. Material: Stainless Steel 3. Dimension: ( L X W X H) 30 To 32 Inches X 14 To 38 Inches X 62 To 64 Inches (minimum) 4. Comes With 4 Caster Wheels 5. The Item Must Be Of Good Quality 3 Piece Comforter 1.type:comforter 2. Material: Polyester 3.color: Any Color 4. Dimension: ( L X W) 84 To 88 Inches X 62 To 65 Inches (minimum) 5.thickness: 20-30 Mm (minimum) 6.washable 7. The Item Must Be Of Good Quality 3 Piece Commode 1.type: Foldable Commode 2. Durable Plastic Snap- On Seat And Lid Withouot Pushing Buttons 3. Blue Powder-coated Steel-welded Construction 4. Plastic Arms For Added Comfort 5.comes Complete With 12 Qt. Commode Bucket With Carry Handle, Cover And Splash Shield 6. Specifications: Width 18 Inches Between Arms/ 22.5 Inches Outside Approximate 7. Set Dimensions: W 32 -36 Cm X D 35 -40 Cm, Height 38 -54 Cm Approximate 8. Weight 13 Lbs., Weitgh Limit 350 Lbs. 9. The Item Must Be Of Good Quality 5 Set Cooking Utensils 1. Material: Stainless Steel 2. The Set Is Comprised Of Ff:; 1 Pc. -16 X 9.5 Cm Sauce Pan With Glass Lid (minimum) 3. 1 Pc. - 16 X 95 Cm Casserole With One Glass Lid, (minimum) 4. 1 Pc. - 18 X 10.5 Cm Casserole With Glass Lid, (minimum) 5.1 Pc. - 20 X 11. 5 Cm Casserole With Glass Lid, (minimum) 6. The Item Must Be Of Good Quality 2 Piece Crutches, Adjustable 1.type: Adjustable Crutches 2. Set Includes: 3 Pcs./set 3.material: Aluminum Powder-coated 4. Color: Any Color 5.weight Capacity: 300 Lbs. (minimum) 6. Dimensions: Youth Size 7. User Heights: 4 Ft. 6 Inches To 5 Ft. 2 Inches 8. Underarm Height: 37 Inches To 46 Inches 9. Adult Size: User Heights: 5 Ft. 2 Inches To Ft. 10 Inches 10. Underam Heights: 45 Inches To 53 Inches 11. Tall Adult Size: User Heights: 5 To 10 Inches 12. Underam Height: 53 Inches To 61 Inches 13. The Item Must Be Of Good Quality 10 Piece Cutlery 1.material: Stainless Steel 2. 20 Pieces Set For 4 3. 4 Dinner Knives 4. 4 Dinner Forks 5. 4 Dinner Spoons 6. 4 Salad Forks 7. 4 Tea Spoons 8. The Item Must Be Of Good Quality 10 Piece Cutting Board, Plastic 1. Material: Polyethylene Plastic 2. Color: Any Color 3. Dimension: ( L X W X H) 240 - 260 Mm X 140 - 160 Mm X 10 - 15 Mm (minimum) 4. Reversible Cutting Surface 5. The Item Must Be Of Good Quality 10 Piece Digital Thermometer, 32 C-42.9 C (90.0f-109.9f 1. Case Material: Hard Plastic (pe) Polyethylene 2. Color: Any Color 3. Range: 32 C - 42.9 C (90.0f-109.9f) 4. Accuracy: + 0.1c 35.5c-42.0c(+ 0.2 F 95.9f-107.6f) 5. Battery Operated 6.memory: Last Measuring Reading 7.alarm: Approx. 10 Seconds Sound Signal When Peak Temperature Reached. 8. The Item Must Be Of Good Quality 2 Piece Dressing Trolley 1.material: Shelves: Powder-coated Steel Sheet 2. Dimensions: ( W X D X H) 48 - 50 Cm X 48 - 50 Cm X 83 - 85 Cm (minimum) 3.number Of Shelves: 2 4. With Four Revolving Castors, Two Lockable 5. The Item Must Be Of Good Quality 10 Piece Electric Knife 1. Type: Electric Knife 2. Material: Stainless Steel And Hard Plastic, (pe) Polyethylene 3. Power Supply: 220/240 Volts, Ac 50/60 Hz. 4. Dimensions: 4.25 X 2.75 X 11.88 Inches (minimum) 5.comes With Touch Button Control, Safety Lock And English User & 39;s Manual 6. Comes With English Manual That Contains: Users Guide, List Of Parts, Maintenance Guide, 7. The Item Must Be Of Good Quality 10 Piece Face Towel/towellete 1. Type: Face Towel 2. Material: 100% Cotton 3. Color: White 4. Dimension: ( L X W ) 28- 32 Cm X 28 -32 Cm (minimum) 5. Washable 6. The Item Must Be Of Good Quality 10 Piece Feeding Bottle Brush 1. Bristle Material: Nylon 2. Color: Any Color 3. Handle Material: Hard Plastic, (ps) Polystyrene 4. Total Length: 280 -320 Mm (minimum) 5. Fit With The Standard Feeding Bottle For The Baby 6.comes With Nipple Brush 7. Washable 8. The Item Must Be Of Good Quality 5 Set Feeding Utensils (child) 1.material: Hard Plastic, (ps) Polystyrene 2. Sets Includes: 6 Pcs./set 3. 1 Pc Knife 4. 1 Pc- Plate 5. 1 Pc. -bowl 6. 1 Pc. - Cup 7. 1 Pc. -fork 8.1 Pc. - Spoon 9. Color: Any 10. The Item Must Be Of Good Quality 7 Set First Aid Kit Type: Emergency Case; Contents: First Aid Quick Reference Guide, 1 Pc; Sterize Gauge Swab (4x 4 X 12 Ply) 100 Pcs/pack, 1 Pack; Adhesive Strips/band-aid, 50 Pcs/pack, 2 Packs; Gloves, Disposable, Medium Size, 2 Pairs; Hypo Allergenic Adhesive Tape, 5 Cm X 5 Cm, 2 Rolls; Triangular Bandage/arm Sling, Min 90 Cm X 90 Cm X 120 Cm, 2 Pcs; Safety Pins, 1 1/4 Inches, (12 Pcs), 1 3/4 Inches (12 Pcs); Stainless Steel Bandage Scissors, 2 Pcs; Betadine, 60ml, 2 -3 Years Expiration, 2 Bottles; Dust Mask, 2 Pcs; Hand Towels Or Face Towels, White Color, 6 Pcs; Gauze Bandage, Minimum 5 Cm X 4cm, 2 Rolls; Antiseptic Handwash/germicidal Soap, 60 Gms, 2 Pcs; Torniquet, 2 Pcs; Spirit Of Ammonia, 30ml, 2-3 Years Expiration, 1 Bottle; Burn Cream Ointment, 20g To 30g, 2-3 Years Expiration, 1 Tube; Medical Tweezers Min. 8 Cm, Plastic, 2 Pcs; Plastic Bags, Resealable, Minimum Of 24 Pcs, 100mm X 180mm, 24 Pcs, 150mm X 230mm; Cotton Balls, 50 Balls In A Sealed Package, 2 Packs; Hot And Cold Pack, Reusable, 1 Pack; Water Resistant And Sturdy Case W/ Handle That Can Accomodate All The Listed Items. 20 Piece Flat Sheet 1.type:bed Sheet 2. Material: 100% Cotton 3. Color: White 4. Dimension: Width - 137 - 145 Cm Length - 180 -200 Cm (minimum) 5. Washable 6. The Item Must Be Of Good Quality 10 Piece Garbage Bin Type: Swivel Lid Garbage Bin Body Shape: Round Material: Hard Plastic, Polypropylene Dimension: 4 Gallons ( Minimum) Removable Dome Shape Lid With Spring Return Swivel Preferably With Packing Case Color: Any Color Smooth And No Rough Surfaces 20 Box Gloves, Rubber (15 Mils) Medium Size (#8) Super Nitrile, Flocklined Interior (acid/solvent Resistant) Individually Packed For Hand Protection 10 Box Gloves, Surgical (disposable) 1.material: Latex 2. Color: White 3. Thickness: .09 Mm (minimum) 4. Disposable And Sterile 5. The Item Must Be Of Good Quality 20 Piece Gown (hospital) 1.type:unisex Hospital Gown 2. Material: Polyester- Cotton 3. Color: Any Color 4. Size: One Size Fits All 5. Comes With Overlap Back Closure 6. The Item Must Be Of Good Quality 5 Set Grooming Kit (hairbrush Comb, Nail Cutter, Nail Brush) 1. Set Includes: 6 Pcs./ Set (minimum) 2. Materials: Stainless Steel And Hard Plastic 3. 2 Nail Clippers/ Trimmers Of Different Sizes 4.1 Multipurpose Scissors 5. 1 Ear Pick 6. 1 Tweezer 7. 1 Comb 8. The Item Must Be Of Good Quality 10 Piece Hand Towel 1. Type: Hand Towel 2. Material: 100% Cotton 3. Color: Any Color 4. Dimension: ( L X W) 65 -75 Cm X 32 -42 Cm (minimum) 5. Washable 6. The Item Must Be Of Good Quality 3 Piece High Chair/booster Seat/ Portable Seat 1. Material: Foldable Powder Coated Steel Frame Or Its Equavalent 2. Phone Type: Corded 3. Polyester Harness, Seat/back Cushion 4. Overall Dimensions: ( L X W) 65 -75 Cm X 50 -60 Cm X 90 - 102 Cm (minimum) 5. Capacity: 40 Lbs. (minimum) 6. With 3-position Seat Recline 7. The Item Must Be Of Good Quality 10 Piece Hot Water Bag 1. Material: Rubber Or Its Equavalent 2. Color: Any Color 3. Overall Dimension: (lxw) 200- 300 Mm X 150 -200 Mm (minimum) 4. Leak-proof And Washable 5. The Item Must Be Of Good Quality 10 Piece Kettle 1. Material: Heat-resistant Hard Plastic 2. Capacity: 1- 1.5 Liters (minimum) 3. Height: 25-35 Cm (minimum) Approx 4. Voltage: 220/240 Volts, Ac 50/60 Hz 5. Power In Watts: 1000 To 1500 Watts 6.comes With Automatic Shut-off Feature And Permanent Water Level Indicator 7. Pitcher-type With Pouring. 8. Comes With English Manual That Contains: Users Guide, List Of Parts, Maintenance Guide, 9. The Item Must Be Of Good Quality 10 Set Measuring Cups .. 1/4, 13, 1/2 1 Cup Set 1. Materials: Stainless Steel 2. Set Includes: 4 Pcs./set; 3. 1 Pc. - 1/4 Cup (60 Ml) 4. 1 Pc- -1/3 Cup (80ml) 5. 1 Pc.- 1/2 Cup (125 Ml) 6. 1 Pc. - 1 Cup ( 250 Ml) 7. Thickness: .5 Mm To 1 Mm (minimum) 8. The Item Must Be Of Good Quality 10 Piece Medical Tray 1. Type: Tray 2. Material: Stainless Steel 3. Overall Dimension: (lxw X D) 300- 350 Mm X 200 -250 Mm X 12 - 19 Mm (minimum) 4. Thickness: .7 To 1 Mm (minimum) 5. The Item Must Be Of Good Quality 2 Set Mixing Bowl, Stainless, 6-piece Set 1. Material: Stainless Steel 2. Quantity Of Set: 6 Pcs./set 3. Dimension: 3/4 Qt., 1.5 Qt., 3 Qt., 4 Qt., 5 Qt., 8 Qt., 4. The Item Must Be Of Good Quality 10 Piece Pail, Plastic, 10 Liters 1. Material: Polyethylene Plastic 2. Dimension: 25-30 Cm Diameter X 23-27 Cm Depth (minimum) 3. Color: Any Color 4. Chromed Finished Handle 5. Capacity: 10 Liters (minimum) 6. Material Must Be Non-toxic 7. The Item Must Be Of Good Quality 10 Piece Pans 1. Type: Frying Pan 2. Material: Stainless Steel 3. Handle: With Hard Plastic Heat Insulation 4. Tempered Glass Lid With Steam Hole 5. Size 23 -26 Cm With Lid 6. The Item Must Be Of Good Quality 10 Piece Peeler 1. Type: Peeler 2. Blade Material: Stainless Steel 3. Handle Material: Stainless Steel 4. Overall Dimensions: 18 X 8 Cm (minimum) 5. Comes With Self-locking 6. The Item Must Be Of Good Quality 10 Piece Pick Up Forcep 1. Type: Curved Forceps 2. Material: Stainless Steel 3. Overall Length: 100-130 Mm (minimum) 4. Comes With Self-locking 5. The Item Must Be Of Good Quality 10 Piece Pillow 1. Material: Cotton 2. Color: Any Color 3. Dimensions: ( L X W) 50 - 56 Cm X 75 - 180 Cm (minimum) 4. With 4 Inches Hems 5. Washable 6. The Item Must Be Of Good Quality 20 Piece Pillow Case 1. Material: Cotton 2. Color: Any Color 3. Dimensions: ( L X W) 50 - 56 Cm X 75 - 180 Cm (minimum) 4. With 4 Inches Hems 5. Washable 6. The Item Must Be Of Good Quality 10 Piece Portable Mixer 1. Type: Portable Mixer 2. Material: Stainless Steel, Clear Acrylic 3. Capacity: 16-18 Oz. (minimum) 4. Size: 170 - 220 Mm X 75- 100 Mm 5. Requires 2 Aaa Batteries 6. Power In Watts: 250 To 300 Watts 7. The Item Must Be Of Good Quality 10 Piece Potato Masher 1. Type: Portable Masher 2. Material: Stainless Steel And Hard Plastic 3. Mesh Head Diameter: 70-90 Mm (minimum) 4. Overall Length: 250 - 270 Mm (minimum) 5. Handle Length: 120-140 Mm (minimum) 6. Washable 7. The Item Must Be Of Good Quality 5 Set Pots 1. Type: Cooking Pot 2. Material: Stainless Steel 3. Set Includes: 4 Pcs./set 4. 1 X Pot With Lid 5. 1 X Pan With Lid 6. 1 X Strainer 7. 1 X Egg Streamer 8. Size: (l X W X H) 40 To 42 Cm X 12 To 14 Cm X 26 To 28 Cm 9. The Item Must Be Of Good Quality 5 Piece Skillet 1. The Item Shall Have The Following Specifications. Material Including Handle: Cast Iron 2. Color: Any Color 3. Dimension ( Dia. X Depth): 250 - 320 Mm X 50 - 70 Mm (minimum) 4. Handle Casted With The Body And Having Plastic Or Rubber Heat Insulator 5. Body Thickness: 1.5 - 3 Mm (minimum) 6. Washable 7. The Item Must Be Branded And Have Good Quality. 5 Piece Sphygmomanometer 1. Type: Aneroid 2. Material: Nylon Cuff And Inflation Bag, Die - Cast Zinc Manometer 3. Package Inlcluded: 1 X Aneroid Sphygmomanometer. 4. Size: ( L X W X H Cm) = 18 To 20 Cm X 11 To 13 Cm X 11 13 Cm 5. Nylon Zippered Carrying Case 6. Capacity: 0 To 300 Mm Hg 7. The Item Must Have Good Quality. 5 Piece Stethoscope 1. Type: Dual Head Stethoscope 2. Material: Stainless Steel Chestpiece And Eartubes 3. Reinforced Pvc Tubing 4. Soft Pvc Eartips 5. Color: Any Color 6. Bell Diameter: 18-25 Mm Approx. 7. Diaphragm Diameter: 25-50 Mm Approx. 8. Overall Length: 66-75 Cm (minimum) 9. The Item Must Be Of Good Quality 5 Piece Urinal 1. Type: Unisex Portable Urinal 2. Material: Hard Plastic, (pp) Polypropylene 3. Color: Any Color 4. Total Capacity: 28 Oz. Minimum 5. Dimension: ( L X W X H) 270 To 290 Mm X 145 To 160 Mm X 70 To 80 Mm ( Minimum) 6. Thickness: 1 Mm To 3 Mm (minimum) 7. The Item Must Have Good Quality. 5 Piece Vacuum Cleaner 1. Material: Plastic (pp) Polypropylene Or Its Equavalent 2. Color: Any Color 3. Suction Power: 18 To 22 Kpa (minimum) 4. Tank Capacity: 24 Liters (minimum) 5. Vacuum Hose Length: 6 To 8 Ft. (minimum) 6. Power Supply: 220 V - 240 Ac , 50/60 Hz. 7. With Accesories: Extension Wand, Utility Nozzle, Standard Paper Filter 8. Comes With English Manual That Contains: Users Guide, List Of Parts, Maintenance Guide, Safety Guide 9. The Item Must Be Branded And Good Quality 3 Piece Wheel Chair 1. Type: Foldable Wheel Chair 2. Overall Dimensions: ( L X W X H) 40 - 44 Inches X 26 - 30 Inches X 34 - 38 Inches ( Minimum) 3. Folded Dimensions: ( L X W X H ) 40 To 44 Inches X 10 To 14 Inches X 34 To 38 Inches (minimum) 4. Capacity: 350 Lbs. (minimum) 5. With Padded Arm Rests; With Push-to-lock Wheel Brakes 6. The Item Must Be Of Good Quality Lot 2. Sta. Maria National High School (hairdressing Nc Ii)- Php 323,170.00 5 Pcs. Bowl, Mixing, Plastic With 10.5 Cm X 6cm 2 Pcs. Bowl, Shampoo, Stainless Steel Frame, Bowl Dimensions: 19 Inch X 20 Inch X 10 Inch With Hose Attachment Of 7 Ft. 5 Box Box, Hairpin, Metal With 3.5 X 4.5 X 0.5 Inches(100 Pcs Per Box) 5 Pcs. Brush, Applicator, Plastic With 70mm X 80mm 5 Pcs. Brush, Hair, Plastic Bristle And Wooden Handle, Width - 2 Inches 10 Pcs. Cap, Frosting, With Hook, Silicone With 31cm X 22cm,rounded Metal Hook 10 Pcs. Cap, Heating, Waterproof, Cordless With 21-24 Inches 10 Pcs. Cape, Polyester With 125 Cm X 140 Cm 5 Pcs. Chair,high, Metal Painted With Anti Rust With 15 Inches X 33 Inches, Synthetic Leather Seat 5 Pcs. Chair, Hydraulic, Metal Base With 59 Cm X 54 Cm X 51-78cm, 180kg, 360' Rotation 10 Pcs. Clamp, Plastic, Length:9.5cm, Thickness:10mm 10 Pcs. Clamp, Duck Bill, Metal, Length: 11 Cm, Elasticity Stainless Steel Spring 5 Pcs. Clipper, Hair, Body Material: Hard Plastic, Blade Material: Carbon Steel, 6 Watts 10 Pcs. Comb, Afro, Plastic, Length: 7 Inches, Width: 3.25 Inches, Number Of Teeth: 12 Teeth, Teeth Height: 2.5 Inches 10 Pcs. Comb, All Purpose, Plastic, 18 Cm Long , Has Both Fine And Medium Teeth Position On One Side Only, Height Of The Teeth: 2 Cm 10 Pcs. Comb, Haircutting, Hard Plastic, Length Including The Handle:180mm, Width: 30mm With Detachable Steel Blades And Blade Holder 10 Pcs. Comb, Large Toothed, Plastic, Size:15 Cm, Number Of Teeth: 10 Teeth, Gap Between Comb's Teeth: 0.4 To 0.5 Cm , Teeth Size: 0.3 Cm X 4cm 10 Pcs. Comb, Tail, Plastic, Size : 8 Inches X 1 Inches, Tail Length: 4 Inches Tooth Length: 3/4 Inch 10 Pcs. Comb, Teasing, Plastic,1st Row: Large Teeth 25 Mm Long, 2nd Row: Small Teeth 19 Mm, Over-all Size: 20cm X 3.8 Cm 5 Pcs. Comb, Wide Tooth, Plastic, Size:15 Cm, Number Of Teeth:10 Teeth, Gap Between Comb's Teeth:0.4 To 0.5 Cm, Teeth Size: 0.3cm X 4cm 8 Pcs. Crimpers, 25 Watts, Size:38 Cm X 15.5 Cm X 9 Cm, Maximum Temp.: 200 Degrees Centigrade, Rated Voltage:10 -230volts Ac 5 Pcs. Curling Iron, Ceramic, 65watts, 210-240volts Ac, Barrel Size: 1 Inch, Adjustable Heat Setting Of 200 Degrees Centigrade, Swivel Cord Up To 360 Degree 5 Pcs. Drip Pan, Hard Plastic, Size:17.5 X 25.8 X 1 Inches, Thickness: 1/8 Inch, Shallow Rectangular Type 5 Pcs. Dryer, Hair, 1000w, Rated Voltage: 220vac, 18.5cm X 16cm X 6.5cm With Plastic Handle Design 10 Box Gloves, Disposable, Size: 25cm X 23cm, 100 Pcs Per Box 5 Pouch Gloves, Rubber, Medium, Thickness: 4 Mil, Acid Resistant 5 Pouch Gown, Smock, Polyester, Sizes: Small (50inches X 56inches);medium (52inches X 58inches); Large (54 Inches X 60inches) 10 Pouch Hairclips, Metal, Size:67mm X 19mm 10 Pack Hairnet, Invisible, Nylon, Size: 55mm, Stretchable, Color: Black 10 Pc Headband, 6 Inches, Woven Crochet Tube 10 Pc Headband, Flannel, Cloth, Size : 45 Cm, Width: 8 Cm 6 Pc Infrared Iron, Ionic Ceramic Tourmaline-infused Plates And Abs Plastic Body, Power: 70 Watts, Power Rating: 220-240 Volts Ac; Over-all Size: 24 Cm, Heating Plate 50 Mm, Heating Time: Within 30 Seconds;variable Heat Settings: From 250 To 450 Degrees Fahrenheit 10 Pc Mirror, Hand, Plastic, Size 15 Cm Diameter, Frame Thickness: 6.5mm, Over-all Length With The Handle: 20 Cm 3 Pc Mirror, Modular, Plain Mirror, Mirror Material: Glass, Frame Material: Aluminum (cut To Fit), Dimensions: 75 Cm X 65 Cm, Mirror Thickness: 6mm 10 Pc Prong Clip, Double, Steel, Size: 45 Mm 10 Pc Prong Clip, Single,steel, Size: 55 Mm 10 Pc Razor, Straight, High Carbon Steel, Foldable Straight Razor, Replaceable Blade; Dimensions: 14 Cm X 2 Cm When Folded; Double-edged Razor Blades 3 Dz Roller Pins, Metal, Size: 60mm Long, Quantity By Dozen(12 Pieces) 10 Pc Rollers, Jumbo, Plastic 44mm In Diameter X 64mm 10 Pc Rollers, Large Sized, Plastic, Size: 40mm Diameter X 60mm Long 10 Pc Rollers, Medium Sized, Plastic; Diameter: 38 Mm ,length: 58mm 4 Pc Scissor, Cutting, Stainless Steel,length: 17cm,blade Width 10 Cm 4 Pc Scissor, Thinning, High Carbon Steel, Blade Length 6cm, Style: Right Handed Scissor, Length: 17cm 5 Pc Scoop, Plastic, Capacity:1/2 Cup, Rounded Edges With Handle Thickness: 1.5 Mm 5 Pc Shower Cap, Plastic, Size: One Size Fits All Or 30cm 5 Pc Spatula, Plastic, Dimension: 7.5 Cm X 1.5 Cm 5 Pc Spray Gun, Transparent Plastic, Capacity: 300ml, Dimension: Bottom Is 7 Cm And The Height Is 17cm 3 Pc Steamer, Hair, 450 Watts, 220 Volts/50-60hz, Hood Material: Polycarbonate, Hood 30 Cm Diameter Opening X 25 Cm, Timer Setting Is Up To 60 Minutes, 32 Ounce Water Reservoir, Adjustable Height 100- 150cm 30 Pcs. Stool, Metal, Electroplated, Load Capacity: 150kg, Design: Swivel Stool With Backrest With Hydraulic Lift To Adjust Height Freely Lot 3. Sta. Maria National High School (wellness Massage Nc Ii)-php 198,338.00 5 Pcs. Dummy, Anatomical, Plastic, 32" Tall, 27 Removable Parts That Are Held On By Metal Screws, Posts, And Hooks, Brain (2parts), Lungs (2 Parts), Heart (2 Parts, Liver, Intestines, Stomach, Base Is 13" X 9" (removable), Weighs 12 Lbs. 5 Pcs. Massage Bed/table, Hard Wood With Steel Bracings, Hardwood Frame, Marine, Plywood Deck; Color: Black, Dimensions: W:75 Cm X L:183 Cm X H: (adjustable) Height: Adjustable From 24 In. - 33in., Leg Thickness - 35mm, Cushion System: High Density Foam (7.5 Cm / 2.95") With Pu Leather Cover (1mm Thick), Weight Capacity: 250 Kg(minimum), Gross Weight: 21 Kg 2 Pcs. Massage Chair, Padded With 3" Thick, High-density, Small-cell Foam, Size: 14"-diameter Seat But Without Back And Arm Rest, With Metal Post And Hard Plastic Star, Pneumatic Spring Will Effortlessly Adjust The Height From 18" To 24" With The Pull Of A Lever, Five Heavy-duty, Smooth-rolling Wheels, Load Capacity: 265 Lbs / 120 Kg (maximum), Smooth Surface And No Sharp Edges 6 Pcs. Sphygmomanometer, 33 To 42 Cm Arm Diameters, Accuracy: ±3mm Hg;measurement Range : 0mm Hg To 300mm Hg; Smallest Scale: 1mm Hg Index And Range Markings On The Dial For Clear Readings, Nylon Cuff Is Durable And Stain Resistant With A Velcro Closure 6 Pcs. Stethoscope, Stainless Steel Double Chest Piece, Color: Black, Tubing Description: Y-tube Pvc, Uses Extra Soft Replaceable And Pivotable Ear Tips, The Binaural Is Chromium-plated, Chest-piece Diameter: 44 Mm And Non-chill Rim, Overall Length: 29" /74 Cm 6 Pcs. Talking Sphygmomanometer, Nylon Cuff Sizes: 33 To 42 Cm Arm Dia, Dimensions: 98mm*126mm*60mm, Measurement Range : 0mm Hg To 300mm Hg; Smallest Scale: 1mm Hg, Weight: 450g , Range: 20~280mmhg(0.4kpa-37.3kpa), Pressure Accuracy: ±3mmhg(±0.4kpa), Pulse Measurement Range: 40 ~199 Beats /min, Voltage: 4*aaa Alkaline Batteries 25 Pcs. Talking Thermometer, Hard Plastic, Sensing Unit: Thermistor, Measurement Range: 32 C - 42 C (89.6f-107.6f), Measurement Accuracy: ± 0.1c 32c-42.0c (± 0.2 F 89.6.9f-107.6f), Power Supply: 1.5v Dc, Lr41 Alkaline-magnesium Button Battery Real Voice, Temperature Display: 3-digit, +deg C (deg F) Display In 0.1 Degree Increment, Dimension Approx.: 2.0 (w) X 4.4 (h) X 1.2 (d) Inches / 51 (w) X 110 (h) X 30 (d) Mms 26 Pcs. Thermometer, Digital, Hard Plastic, Sensing Unit: Thermistor, Measurement Range: 32 C - 42 C (89.6f-107.6f), Measurement Accuracy: ± 0.1c 32c-42.0c (± 0.2 F 89.6.9f-107.6f) Power Supply: 1.5v Dc, 1 Lr41 Alkaline-magnesium Button Battery , Power Consumption: 0.1mw, Temperature Display: 3-digit, +deg C (deg F) Display In 0.1 Degree Increment, External Size (mm): 19.4(w) × 132.5 (l) × 10.0(d) 10 Pcs. White Board, White Formica Laminated, Board Size: Rectangular 1800mm W X 1000 To 1200mm H, Board Edges Secured With Aluminum Clip Edging 17 Mm Wih Plastic Corner Caps, The Stand And Frame Are Constructed With Aluminum Or Powder Coated Steel 25mm Square Tube , Sturdy, No Wobble With 4 Lockable Hard Plastic Caster Wheels, Height From Floor: 210 To 214cm Lot 4. Sumirap National High School And Tangub City National High School (bpp Nc Ii)-php 519,702.00 10 Set Air Compressor With Airbrush Cake Decorating Set(airbrush Gravity Feed Dual Action Airbrush Compressor Kit 0.2/0.3/0.5mm Needle Air Brush For Cake Decorating Painting. Material: Aluminum + Copper Type: Single Cylinder Piston Compressor Power: 1/5 Hp Plug Type: Eu Voltage: 220-240v/50hz Speed: 1450 Rpm Air Volume Per Minute/liter: 23l/min Maximum Pressure: 7bar (100psi) Working Pressure Of Spray Gun: 15-50psi Low Noise: ≤50db Accessories: Pressure Gauge, Pressure Gauge, Air Filter Automatic Stop, Starts At 2.8 Bar, Stops At 4 Bar (special Pressures Available) Connection: With Connection G 1/8" Bsp Cable: Approx. 1.8m / 6ft) 40 Pc Egg Beater(stainless Steel Semi-automatic Mixer/manual Whisk Egg Beater Kitchen Cooking Tool) 40 Set Board, Chopping ,6 Color( Type: Food Grade Body Shape: Rectangular Material: Plastic (polypropylene), Food Grade Board Size: Length: 38 Cm (minimum) Width: 30 Cm (minimum) Thickness: 1.27 Cm (minimum) Color-coded For Use With Different Types Of Food, Blue, Red, Yellow, Green, Brown And White, Preferably Packed In Set Comes With No Sharp Edges And With Hole For Storage Purposes) 10 Pc Double Boiler (material: Stainless Steel Thickness: 1/16 Inch (1.5 Mm) (minimum) Lid Material: Glass Rivetedhandle On Both Side Diameter: 9 1/2 Inches (minimum) Total Height: 9.4 Inches (minimum) Inset Bottom Diameter: 9 Inches (minimum) Inset Top Diameter: 9 Inches (minimum) Capacity: 2 Liters (minimum) Must Be A Set Which Includes One (1) Saucepan, One (1) Boiler, And One (1) Lid With Stainless Steel Handle And Smooth Surfaces With No Sharp Edges) 80 Set Bowl, Mixing Set Stainless (premium Stainless Steel Mixing Bowls Bowl Sizes Are: 5 Qt, 4 Qt, 3qt, 1.5qt, And ¾ Qt And They Each Fit Perfectly Within One Another) 70 Set Cake Pan, Round, Size: 4''x3'' (non-stick Aluminum Alloy Cake Round Pan) 30 Set Cake Stand, With Tier (type: Cake Stand With Tier, Food Grade Body Shape: Circular With 3 Tier Material: Hard Plastic, Polypropylene, 4 Mm Thick The Tier Consists Of The Following Sizes: Tier 1: 18 Cm Diameter (minimum) Tier 2: 25 Cm Diameter (minimum) Tier 3 : 30 Cm Diameter (minimum) Column Diameter: 20 To 30 Mm (solid) Distance Between Tiers: 15 Cm Over-all Length: 30 Cm (minimum) Assembled Column Is Used For Maximum Strength And Stability Of The Stand Must Be Packed In Set ) 60 Pc Cake Turn Table (type: Turn Table Body Shape : Circular Material: Cast Aluminum Plate.and Cast Iron Base Upper Plate: 30 Cm Diameter (minimum) And 1.4 Cm Thickness (minimum) Base Dimensions: 18 Cm (minimum); 1.4 Cm Thickness (minimum) Total Height: 10 Cm To 15 Cm Turntable With Ball Bearing To Turn Easier Preferably Packed In Any Kind Of Packaging Comes With No Sharp Edges To Rotate Smoothly In 360 Degrees Clockwise Or Counter Clockwise ) 30 Pc Coupler (type: Foood Grade Body Shape: Tubular Material: Hard Plastic, Polypropylene, Any Bright Color Height: 3cm (minimum) Top Diameter: 1.27 Cm (minimum) Bottom Diameter: 2.54 Cm (minimum) Preferably With Storage Case The Materials Used Must Be Non-toxic And Dishwasher Safe ) 50 Set Cup, Measuring (stainless Steel Measuring Cup Set For Dry Ingredients. Composed Of 1 Cup, 3/4 Cup, 1/2 Cup, 1/4 Cup, 1/8 Cup) 50 Set Cup, Measuring 250 Ml. For Liquid Glass (250 Ml Heat Resisting Measuring Glass) 40 Set Cup, Measuring 500 Ml. For Liquid Glass (500ml Heat Resisting Measuring Glass) 40 Pc Cutter, Dough (type: Scrapper Body Shape: Straight Blade Material: Stainless Steel Straight Blade With Stainless Steel Handle Blade Dimension: Lenght : 15 Cm X Width: 11 Cm X Thickness: 1.2 Mm(minimum) Handle Dimension: Length: 15 Cm X Diameter: 3 Cm (minimum) Preferably With Packing Case Food Grade And Dishwasher Safe Design Allows Item To Be Hung For Storage) 40 Pc Cutter, Pie (stainless Steel Rolling Knife/pizza Cutter) 30 Pc Flour Sifter,hand Cranked (type: Hand Cranked Body Shape: Round Shape Material: Stainless Steel Dimension: Diameter: 133.3 Mm ( Minimum) X Height: 165 Mm (minimum) Thickness: 0.79 Mm (minimum) (body) And Constructed With Stainless Steel Wire Mesh # 30 Bottom Volume Markings Should Be Seen Inside And Outside Of The Sifter Capacity: 5 Cups (1.18 Liter) Spring Action Squeeze Handle Stainless Steel Preferably With A Packing Case Dishwasher Safe) 40 Pc Grater (type: Four Sided Box Grater Body Shape: Box In Shape Material: Stainless Steel Blade And Plastic (polypropylene Handle) Grater Dimensions: Height- 25 Cm X Width-13 Cm X Depth-10 Cm (minimum) Side 1: Large-hole Shredder With 6 Mm Hole Side 2: Slicer Side 3: Small-hole Shredder With 3 Mm Hole Side 4: Grater With Strips About 1.27 Cm To 2.54 Cm Length Preferably With Packing Case Food Grade & Dishwashing Safe) 50 Pc Knife, Kitchen (premium Quality Stainless Steel Kitchen Knife, 6-8” In Length) 20 Pc Knife, Pallete (premium Quality Stainless Steel Pallete Knife Ideal For Butter.) 50 Pc Ladle, 3oz (premium Quality Stainless Steel Soup Ladle, 3oz) 40 Pc Loaf Pan, Big (carbon Steel Non-stick Loaf Pan, Size: L=32,w=13,h=7cm Minimum) 40 Pc Loaf Pan, Medium (carbon Steel Non-stick Loaf Pan, Size: L=28, W=15.5, H=7cm Minimum) 40 Pc Loaf Pan, Small (carbon Steel Non-stick Loaf Pan, Size: L=25.5, W=13.5, H=6cm Minimum) 40 Pc Muffin Pan, Big (carbon Steel Non-stick Muffin Pan, 12 Holes,3oz) 40 Pc Muffin Pan, Medium (carbon Steel Non-stick Muffin Pan, 9 Holes,3oz) 40 Pc Muffin Pan, Small (carbon Steel Non-stick Cupcake Pan, 6 Holes) 70 Pc Pie Pan, 10'' (premium Stainless Steel/aluminum Pie Plate. Thick And Durable, 10” In Diameter) 70 Pc Pie Pan, # 8 (premium Stainless Steel/aluminum Pie Plate. Thick And Durable, 8” In Diameter) 50 Set Pillars, Cake (premium Quality Acrylic Cake Support Pillar, 12cm In Diameter(minimum),straw Size Diameter ) 60 Pack Piping Bag (reusable Silicone Piping Bag, Biggest Size, 100pcs Per Pack) 40 Pc Rectangular Pan (carbon Steel Non-stick Rectangular Cake Pan. Size: L=10.8", W=7", H=1.5", Minimum) 70 Pc Rolling Pin, Plastic (non-stick Rolling Pin Made With Food Grade Nylon, Size:13") 100 Pc Rubber Scraper, Silicone (size: 21cm X 4.1cm, Material: Silicone) 40 Pc Sauce Pan Non Stick (non-stick Sauce Pan With Lid, Size: 20cm) 40 Pc Sheet Pan / Cookie Sheet (aluminum Baking Sheet, Size: 13x18”) 50 Set Spoon, Measuring (premium Quality Stainless Steel Measuring Spoon Set, Compost Of 1/8tsp, 1/4tsp, 1/2tsp, 1tsp, 1/4tbsp, 1/2tbsp, 1tbsp)) 70 Pc Spoon,wooden (premium Quality And Durable Long Handled Wooden Spoon/ladle. Length: 30.5cm Minimum) 40 Pc Strainer (stainless Steel, Fine Mesh Strainer, Size: 18cm) 40 Set Tip, Decorating, Large (type: Tube Tips Body Shape: Nozzles With Different Shape Material: Stainless Steel Tube Height: 3.5 Cm To 5 Cm Tube Diameter: 2 Cm To 3.5 Cm Thickness: 0.5 Mm (minimum) Tube Tip: Assorted Designs (create Swirls, Rosettes, Flowers, Roping,stars, Leaves And Other Designs Comes With 24 Different Shapes Of Nozzles Packed In Plastic Storage Box Smooth And Deformities Free Must Be Branded) 30 Pc Weighing Scale, 10 Kg. (kitchen Weighing Scale, 10kg Maximum) 40 Pc Weighing Scale, 5 Kg. Digital(digital Kitchen Weighing Scale, Digital Price Computing Weight Electronic Scale, Capacity Is At Least 5kilograms, Pan Size 34.5 X 23.5cm) 70 Pc Wire Whisk, Medium (stainless Steel Wire Whisk, Size: 14”) Lot 5. Sumirap National High School And Tangub City National High School ( Cookery Nc Ii )-php 1,405,964.00 30 Pcs. Apple Corer, Body Shape: Tubular Material: Stainless Steel Total Length: 18 Cm (minimum) Handle Material: Hard Plastic, Polypropylene Handle Dimension: Length-10 Cm X Diameter-2 Cm (minimum) Blade Size: Length-8cm X Diameter-2 Cm (minimum) Preferably With Packing Case Dishwasher Safe. 4 Pcs. Bain Marie, Table, (food Warmer) Body Shape: Rectangular Material: 304 Stainless Steel, 0.8 Mm Thick (minimum) Dimensions: Length-1500 Mm X Width-700mm X Height-800 Mm (minimum) Power Soiuce: Voltage: 220 Volts - 230 Volts, 50 Hz/ 60 Hz With Royal Cord 1.5 Meter Long With Attachment Standard Type A Male Plug Or Provide Plug Adopter 10a/220v 20 Pcs. Blender, Electric Heavy Duty, Body Shape: Round Jar Material Housing: Plastic (polypropylene) Jar Height : 25 Cm To 28 Cm Jar Thickness: 4 Mm To 8 Mm Heat Resistant Glass Jar With Cover Source Voltage: 220 Volts / 240 Volts,50 Hz / 60 Hz With Power Cord 1.5 Meter Long With Attachment Of Standard Type A Male Plug Or Provide Plug Adopter 10a/220v. Power Wattage: 300 To 700 Watts Blade: Stainless Steel, 3 To 4 Metal Blades 40 Pc Board, Chopping/ Cutting, Plastic, Body Shape: Rectangular Material: Plastic (polypropylene), Food Grade Board Size: Length: 15 Inches (minimum) Width: 12 Inches (minimum) Thickness: 0.5 Inch (minimum) With Hole For Storage Purposes Preferably With Packing Case Food Grade And Dishwasher Safe. 20 Pcs. Boiler, Double, Material: Stainless Steel Thickness: 1/16 Inch (1.5 Mm) (minimum) Lid Material: Glass Riveted Handle On Both Side Diameter: 9 1/2 Inches (minimum) Total Height: 9.4 Inches (minimum) Inset Bottom Diameter: 9 Inches (minimum) Inset Top Diameter: 9 Inches (minimum) Capacity: 2 Liters (minimum) 30 Pcs. Braising Pan, Medium, Body Shape: Round Material: Enameled Cast Iron And Stainless Steel Size: Diameter: 28 Cm X Height: 10 Cm (minimum) Capacity: 4 Liters (approximate) With Stainless Steel Cover, Solid Cast Stainless Steel Side Handles And Riveted Handle On Both Side: Length: 10 Cm (minimum) Handle Diameter: 8 Mm To 10 Mm 30 Pcs. Can Opener, Body Shape: Materials: Stainless Steel Dimension: Length-21 Cm X Width 10 Cm X Depth:2.5cm (minimum) Multi-use: 3 In 1 Can Opener Also Opens Bottle Tops- Can Lids And Tabs. 30 Pcs. Casserole,medium Pot, Body Shape:round Material:stainless Steel, 0.7 Mm Thick Dimension: Diameter- 24 Cm X Height -14 Cm (minimum) Tempered Glass Lid Welded Handle On Both Sides, Size: 7.5 Cm (minimum) Handle Diameter: 8 Mm To 10 Mm Preferably With Packing Case . 30 Pcs. Casserole,small Pot, Body Shape: Round Material: Stainless Steel, 0.7 Mm Thick Dimension: Diameter- 20 Cm X Height -12 Cm (minimum) Tempered Glass Lid Welded Handle On Both Sides, Size: 7.5 Cm (minimum) Handle Diameter: 8 Mm To 10 Mm. 20 Pcs. Colander, Medium, Medium Body Type: Round Material: 304 Stainless Steel Diameter: 30 Cm (minimum) Capacity: 8 Quarts (9 Liters) Welded Handle On Both Sides, Size: 7.5 Cm (minimum) Handle Diameter: 8 To 10 Mm Body Thickness: 0.8 Mm (minimum) 20 Pcs. Colander, Small, Body Shape: Round Material: 304 Stainless Steel Diameter: 26 Cm (minimum) Capacity: 5 Quarts (5.6 Liters) Welded Handle On Both Sides, Size: 7.5 Cm (minimum) Handle Diameter: 8 Mm To 10 Mm Body Thickness: 0.8 Mm (minimum) Full-ring Support Base, 15 Cm Diameter Preferably With Packing Case Food Grade And Dishwasher Safe 20 Set Cup,measuring( For Solid) Set Body Shape: Round Material: Stainless Steel, 0.7 Mm Thick (minimum) Each Set Contains The Following: 1 Pc - 1 Cup (237 Ml) 1 Pc - 1/2 Cup (118 Ml) 1 Pc - 1/3 Cup (79 Ml) 1 Pc - 1/4 Cup (59 Ml) Handle Dimension: Length-12 Cm X Width-1 Cm (minimum) Measuring Capacity Engraved On The Handle Strip Handles Have Provision For Hanging Preferably With Packing Case Smooth Surfaces And Dishwasher Safe 20 Pcs. Dispenser,paper Towel Body Shape: Rectangular Material: Abs Plastic Dimensions: Length =260 Mm X Width =100 Mm X Height = 211 Mm (minimum) Capacity: 200 Paper Paper Size: Length-20 Cm X Width- 8 Cm (approximate) Mounting Style: Wall Mounted Tissue Box 12 Pcs. Fan, Electric, Ceiling Material: Metal, Plastic Size/diameter: 18 Inches Power Rating: 70 Watts (minimum), 220 / 240 Vac, 50 / 60 Hz, Single Phase Rotation Angle: 90 Degrees Base: Stable, 16 Inches Diameter (approx.) Removable Metal Guard On Front And Rear 3-speed Settings Comes With 1.5 Meters Power Cord And With Molded Male Plug To Adapt Type A Outlet (or Providing 3a Minimum Plug Adapter Is An Option) Smooth Surface, No Sharp Edges Includes User's Manual In English Which Contains: A. A Diagram Of The Parts With Their Names 6 Pcs. Fire Extinguisher With Contents .for Type A, B, C Fire: Dry Chemicals (monoammonium Phosphate) 2.portable Type 3.capacity : 5 - 6 Kgs 4.rechargeable Cylinder Metal 5.working Pressure Of Cylinder : 400 Psi 6.brass Valve With Pressure Gage 7.with Rubberized Hose And Aluminum Nozzle Attached 8.with Squeeze Lever To Discharge And Safety Pin 10.painted With Metal Primer And Red Enamel Paint 20 Pcs. Fish Poacher,medium, Body Shape: Oval Pot For Poaching Material: Stainless Steel, 0.64 Mm Thick Dimensions (l X W X D): 45 Cm X 15 Cm X 12 Cm (minimum) Handle Material: Stainless Steel Riveted Looped Handles On Both Side, 7 Cm (minimum) Handle Diameter: 8 Mm To 10 Mm Includes Stainless Steel Lid With Handle And Removable Insert 20 Pcs. Fork, Carving Body Shape: Square Shape Prong Prong Material:high Carbon Stainless Steel Overall Length: 30 Cm (minimum) Blade Dimension: Length- 15 Cm X Width- 0.5 Cm X Thickness- 0.3 Cm (minimum) Number Of Prongs: 2 Prong Comes With Square- Shaped Prongs And Pointed Tips Abs Plastictriple-riveted Handle Preferably With Packing Case 400 Pcs. Fork, Kitchen Body Shape: Standard Material: Stainless Steel Dimension: Length - 32 Cm X Width- 3.5 Cm (minimum) Fork Size: Length: 8 Cm X Width -3.5 Cm (minimum) Handle :abs Plastic Number Of Tines: 2 Tines With Tapered End 36 Dozen Frying Pan, Large, Non Stick, Body Shape: Round Pan Material: Aluminum With Non-stick Coating Thickness: 3 Mm Thick (minimum) Dimension: Diameter-30 Cm (minimum) X Height- 5.5 Cm (minimum) 40 Pcs. Frying Pan, Medium, Non Stick, Body Shape: Round Pan Material: Aluminum With Non-stick Coating Thickness: 3 Mm Thick (minimum) Dimension: Diameter-24 Cm (minimum) X Height- 4.5 Cm (minimum) Handle Material: Stainless Steel With Silicone Riveted Handle: 19 Cm Long (minimum) Preferably With A Packing Case 30 Pcs. Frying Pan Small, Non Stick , Body Shape: Round Pan Material: Aluminum With Non-stick Coating Thickness: 3 Mm Thick (minimum) Dimension: Diameter-20 Cm (minimum) X Height- 3.8 Cm (minimum) Handle Material: Stainless Steel With Silicone Riveted Handle: 12 Cm Long (minimum) Preferably With A Packing Case Oven Safe Up To 250⁰f 22 Pcs. Funnel, S/s, Medium, Body Shape: Round Material: 304 Stainless Steel Dimension: Diameter-15 Cm (minimum) X Height- 15.8 Cm (minimum) Tube Diameter: 2 Cm X Length: 7.3 Cm (minimum) Comes With Handle For Easy Hanging Preferably With Packing Case Dishwasher Safe 22 Pcs. Funnel, S/s, Small, Body Shape: Round Material: 304 Stainless Steel Dimension: Diameter-11 Cm (minimum) X Height- 10 Cm (minimum) Tube Diameter: 1.5 Cm X Length: 5 Cm (minimum) Comes With Handle For Easy Hanging Preferably With A Packing Case Dishwasher Safe. 20 Pc Garbage Bin, Body Shape: Round Material: 304 Stainless Steel Dimension: Diameter-11 Cm (minimum) X Height- 10 Cm (minimum) Tube Diameter: 1.5 Cm X Length: 5 Cm (minimum) Comes With Handle For Easy Hanging Preferably With A Packing Case Dishwasher Safe. 20 Pc Glass Rack, Body Shape: Square Material: Polypropylene Plastic Overall Dimensions: Length - 19 1/2 Inches X Width - 19 1/2 Inches X Height - 4 Inches (minimum) Compartments: Full-size 25 Individual Compartment Glass Rack Compartment Dimensions: Length - 3 1/2 Inches X Width - 3 1/2 Inches X Height - 4 Inches (minimum) Easy Grip Handles Molded Into All Four Sides Preferably With A Packing Case 20 Pc Ice Cream Scoop, Stainless Steel Ice Cream Scoop 45mm. Simply Squeeze Handle. 30 Pc Knife,boning, Body Shape: Ergonomic Material: High Carbon Steel Overall Length: 28 Cm (minimum) Blade: Length-15 Cm X Width- 3 Cm (minimum), Pointed Tip Cutting Edge Angle From Tip To The Heel Is 13 To 14 Degrees Handle Length: 12 Cm (minimum) Handle Material: Hard Plastic Handle With Rivets Preferably Wiht Packing Case Dishwasher Safe 30 Pc Knife,chef, Body Shape: Flat Materials: Stainless Steel Overall Length: 30 Cm (minimum) Blade Size: Length - 20 Cm X Width-4 Cm (minimum) Blade Thickness: 2.5 Mm (minimum) 30 Pc Knife,cleaver, Cutting Edge: Straight, Pointed End Type: Cleaver Knife Body Shape: Flat Blade Material: Forged Stainless Steel Heavy Duty Blade Length: 17 Cm (minimum) Overall Length: 30 Cm (minimum Cutting Edge: Straight Handle Material: Ergonomic Wood Handle With Triple Rivets Blade Thickness: 3 Mm (minimum) 30 Pc Knife,oyster, Body Shape: Ergonomic Blade Material: Stainless Steel Blade Dimension: Length - 7 Cm (minimum) X Width - 2 Cm (minimum) Blade Thickness: 2 Mm (minimum) Handle Material: Smooth Wooded Handle Rounded Handle Size: Length-10 Cm X Diameter- 3.5 Cm (minimum) Total Length (from The Tip Of The Handle Up To Tip Of The Blade) :17 Cm (minimum) 4 Pc Light,emergency, 2 Heads Led Materials: Metal, Anti-rust Coated Duration Time (2 Heads): 5 Hours (minimum) Automatically Light Up During Power Outage Overcharge And Over- Discharge Protection Built - In Ac Charger, Power Cord Plug To Adapt Type A Outlet (or Providing 5a Minimum Plug Adapter Is An Option) Battery Test Switch - External Safety Fuse Head: White Led 1w (minimum) 3.5 " Dome Reflector 4 Pc Meat Slicer, Body Shape: Circular Housing Material: Die Cast Aluminum Alloy And Body Painted Dimensions: Width-40.5 Cm X Depth- 45.7 Cm X Height- 38 Cm (minimum) Stainless Steel Rotary Blade Diameter: 190 Mm (minimum) Power Source: 220 Volts-230 Volts, 60 Hz With Power Cord 1.5 Meter Long With Attachment Of Standard Type A Male Plug Or Provide Plug Adopter 10a/220v 30 Set Pastry Tube, Stainless Steel Pastry Tube 24, Big 40 Pc Peeler, Y -type, Rack Dimension: Length: 38 Cm X Width 23 Cm (minimum) Type: Y-type Peelers Body Shape: Ergonomic Material: Stainless Steel Overall Dimensions (l X W X H): 7 Inches X 2 1/4 Inches X 1 Inch (minimum) Blade Material: 304 Stainless Steel, 0.7 Mm Head Dimension: (l X W X H) 2 1/4 Inches X 2 1/4 Inches X 1 Inch (minimum) Handle Material: Stainless Steel Handle Length: 4 3/4 Inches X 1 Inch Diameter (minimum) 2 In 1 Design With 2 Blade Reel, Built In Potato Eye Remover And Hole For Hanger Preferably With A Packing Case 14 Set Pepper And Salt Mill Food Grade And Non-toxic Material. Mill Cookery Nc Ii Type: Pepper & Salt Mill Body Shape: Round Body Material: Wood Size: Diameter: 5 Cm X Height: 20 Cm (minimum) Carved Of Wood With Stainless Steel Grinding Mechanism 20 Pack Piping Bag, Body Shape: Triangular Material: Transparent Disposable Plastic For Dispensing Ingredients To Pastries Length: 9 Inches Minimum Width: 3 Inches (minimum) Volume: 500 Ml (approximate) 10 Pc Plate Rack Shape: Rectangular Material: 304 Stainless Steel Dimension: Length-475 Mm X Width- 290 Mm X Height- 380 Mm (minimum) 12 Set Preparation Table With Sink, Heavy Duty Wire Shelving, 2.6 Mm Diameter (minimum) Table With Sink Cookery Nc Ii Type: Preparation Table With Sink & Sheleves Body Shape: Rectangular Material: Stainless Steel, 1 Mm Thick (minimum) Dimensions: L-1200 Mm X W - 700 Mm X H - 850 Mm (minimum) Stainless Steel Table Top And Stainless Steel Under Shelf Fully Welded Construction Sink: Left Side Single Bowl Sink With Drainer 4 Inches & Faucet Provision Sink Dimension (l X W X D) 400 Mm X 500 Mmx 25 Mm (minimum) 4 Pc Pressure Cooker, Cooker Body Shape: Round Material: Polished Aluminum Dimension: Diameter: 32 Cm X Height: 25 Cm (minimum) Capacity: 10 Quarts (11.3 Liters) Side Handles For Secure Carrying Equipped With Safety Opening Mechanism, Spring Safety Valve, Rubber Seal Ring 24 Pc Roasting Pan , Body Shape:rectangular Material: Stainless Steel Dimension: Length: 40 Cm X Width-35 Cm X Height -7 1/2cm (minimum) Thickness: 1.5 Mm Thick (minimum) Welded Handles On Both Sides Removable Stainless Steel Wire Rack 40 Pc Scissor, Kitchen Type:kitchen Scissor Body Shape: Ergonomic Blade Material: Stainless Steel, 2 Mm Thick Handle Material Heavy Duty Acrylonitrile Butadiene Styrene (abs) Plastic Overall Length: 20 Cm (minimum ) Width: 7.5 Cm (minimum) 30 Pc Siever,small Type: Fine Mesh Siever Body Shape: Round Material: Stainless Steel Diameter: 20 Cm (minimum) Depth: 7 Cm (minimum) Twin Wire Handle: Length 20 Cm X 5 Mm Diameter (minimum) Fine Mesh: 0.7 Mm (1/32 Inch) (minimum) Preferably With A Packing Case 30 Pc Skimmer, Fine Type: Medium Fine Mesh Skimmer Body Shape: Round Material: Stainless Steel, Polished Overall Length: 34 Cm (minimum) Skimmer Head: Diameter -10 Cm X Depth- 4 Cm (minimum) Diameter Of Holes: 2 Mm (approx.) Handle: Length- 12 Cm X Diameter- 2 Cm (minimum) Handle Has Hole For Hanging Preferably With A Packing Case 30 Pcs. Skimmer,spider, Dishwashing Safe Type: Skimmer, Spider Body Shape: Round Material: Stainless Steel, Polished Overall Length: 35 Cm (minimum) Skimmer Head Diameter: 15 Cm X Depth 4 Cm (minimum) Handle Length: 12 Cm X 2 Cm Diameter (minimum) Preferably With A Packing Case Dishwasher Safe. 24 Pcs. Soup Cup, Rack Body Shape: Square Material: Polypropylene Plastic Dimension: Length: 50 Cm X Width: 50 Cm X Height: 10 Cm (minimum) Compartment Length: 11 Cm Compartment Width: 11 Cm Compartment /inside Height: 6.7 Cm No. Of Compartment: 16 Compartments 20 Pc Soup Ladle, 12oz Body Shape: Round Material: Stainless Steel Thickness: 1 Mm Thick (minimum) Handle Length: 34 Cm (minimum) Capacity: 12 Oz. (341 Ml) Ladle Type: Round Bottom Hooked Handle Design Allows It To Easily Sit On The Edge Of Pots. Preferably With A Packing Case Dishwasher Safe 20 Pc Soup Ladle, 3 Oz Body Shape: Round Material: Stainless Steel Thickness: 1 Mm Thick (minimum) Handle Length: 28 Cm (minimum) Capacity: 3 Oz. (85 Ml) Ladle Type: Round Bottom Hooked Handle Design Allows It To Easily Sit On The Edge Of Pots. Preferably With A Packing Case Dishwasher Safe Must Be Branded 20 Pc Soup Ladle 6 Oz. Body Shape: Round Material: Stainless Steel Thickness: 1 Mm Thick (minimum) Handle Length: 30 Cm (minimum) Capacity: 6 Oz. (170 Ml) Ladle Type: Round Bottom Hooked Handle Design Allows It To Easily Sit On The Edge Of Pots. Preferably With A Packing Case Dishwasher Safe 20 Pc Soup Ladle 8 Oz. Body Shape: Round Material: Stainless Steel Thickness: 1 Mm Thick (minimum) Handle Length: 30 Cm (minimum) Capacity: 8 Oz. (236 Ml) Ladle Type: Round Bottom Hooked Handle Design Allows It To Easily Sit On The Edge Of Pots. Preferably With A Packing Case 62 Pc Spatula, Type: Offset Spatula Body Shape: Flat Blade Material: Stainless Steel 316 Handle Material: Hardwood (smooth Finish) With Rivets Blade Dimension: Length= 7 .5 Inches X Width-1.5 Inches (minimum) Thickness Of Blade: 1.7 Mm Thick (minimum) Total Length = 12 To 14 Inches Preferably With A Packing Case Dishwasher Safe Must Be Branded. 400 Pc Spoon, Kitchen Body Shape: Oval Material: Stainless Steel, 1.5 Mm Thick Overall Length: 30.5 Cm X Width-7.5 Cm (minimum) Spoon Head Dimension (l X W) 9 Cm X 7.5 Cm (minimum) Handle: Abs Plastic Spoon Head: Oval Type Preferably With A Packing Case Heat Resistant Up To 220 ° C Dishwasher Safe Must Be Branded. 60 Pc Spoon, Kitchen (slotted) Kitchen Spoon Slotted Body Shape: Oval With Slot Material: Stainless Steel, 1.5 Mm Thick Overall Length: 30.5 Cm X Width-7.5 Cm (minimum) Spoon Head Dimension (l X W) 9 Cm X 7.5 Cm (minimum) 30 Set Spoon, Measuring Body Shape: Bowl In Shape Material: Stainless Steel, 0.7 Mm Thick (minimum) The Set Consists Of The Following Sizes: 1 Pc - 1 Tbsp. (15 Ml) 1 Pc - 1/2 Tbsp. ( 7.5 Ml) 1 Pc - 1 Tsp. (5 Ml) 1 Pc - 1/2 Tsp. (2.5 Ml) 40 Pcs. Spoon, Parisienne Body Shape: Round Double Headed Parisiennes Scoop Bar Tool Material: Stainless Steel, Polished Overall Length: 240 Mm (minimum) Scoop Diameter: 30 Mm And 24mm (minimum) With Plastic Handle (polypropylene), Size: 130 Mm X Width-20 Mm (minimum) Draining Small Hole In The Scoop 40 Pc Spoon, Serving Preferably With A Packing Case Type: Serving Spoon Body Shape: Oval Materials: Stainless Steel Dimension: Length: 23 Cm X Width: 5 Cm (minimum) Scoop Dimension (l X W X D): 7 Cm X 5 Cm X 0.9 Cm (minimum) Spoon Thickness: 1.6 Mm (minimum) Preferably With A Packing Case Dishwasher Safe Must Be Branded. 30 Pc Spoon,wooden Body Shape: Oval Material: Hardwood Dimensions: Length- 10 Inches X Width- 2 Inches (minimum) Bowl Dimension: Length -3 Inches X Width 2 Inches X Depth -3/4 Inches (minimum) Total Length: 10 Inches (minimum) Preferably With A Packing Case Smooth Surface Finished And No Sharp Edges 20 Pc Stock Pot,large . Body Shape: Round Material: Stainless Steel, 0.8 Mm Thick (minimum) Top Diameter: 30 Cm (minimum) Height: 31 Cm (minimum) 30 Pc Strainer, Chinois,small Body Shape: Conical Material: Stainless Steel Strainer Diameter: 20 Cm (minimum) Strainer Depth: 21.5 Cm (minimum) Handle Length: 20 Cm (minimum) With 2 Mm. (approx.) 30 Pc Strainer,chinois,medium Medium Body Shape: Conical Material: Stainless Steel Strainer Diameter: 20 Cm (minimum) Strainer Depth: 21.5 Cm (minimum) Handle Length: 20 Cm (minimum) With 2 Mm. (approx.) 26 Pc Strainer,medium,fine Body Shape: Round Material: Stainless Steel Strainer Diameter: 20 Cm (minimum) Strainer Depth: 7 Cm (minimum) Handle Length: 18 Cm (minimum) With 2 Mm. (approx.) 30 Pc Strainer, Small,fine Body Shape: Round Material: Stainless Steel Strainer Diameter: 13 Cm (minimum) Strainer Depth: 5 Cm (minimum) Handle Length: 13 Cm (minimum) With 1 Mm. (approx.) 30 Pc Tenderizer, Medium Aluminum Meat Tenderizer 16 Pc Thermometer,pocket/pin Pocket/pin Food Thermometer 20 Pc Tong,12'' Body Shape: Standard Material: Stainless Steel Size: 12 Inches Stainless-steel Arms With Soft, Comfortable Grips Nylon Heads Safe For Nonstick Cookware Heat-resistant Up To 400 Degrees Fahrenheit Tongs Lock Closed For Storage Preferably With A Packing Case Food Grade And Dishwasher-safe Must Be Branded 20 Pc Tong 8'' Stainless-steel Arms With Soft, Comfortable Grips Nylon Heads Safe For Nonstick Cookware Heat-resistant Up To 400 Degrees Fahrenheit Tongs Lock Closed For Storage Preferably With A Packing Case Food Grade And Dishwasher-safe Must Be Branded 30 Pc Tray,baking,small, Tray Body Shape: Rectangular Material: Stainless Steel Dimension: 20 Cm X 30 Cm X 3.7 Cm (minimum) 36 Pc Tray,utility,medium,plastic White Plastic, White Multi Purpose 13”x10”utility Tray 30 Pc Turner,3'x6'', Slotted Turner, 3" X 6" Type: Slotted Turner, 3" X 6" Body Shape: Straight Material: Stainless Steel Blade Size (lx W): 6 Inches X 3 Inches (minimum) Handle Length: 5 Inches (minimum) Overall Length: 13 Inches (minimum) Solid Turner With Straight Slotted Blade Wooden Handle With Triple Rivets Preferably With A Packing Case Dishwasher Safe Must Be Branded 4 Pc Utility Cart, Stainless Steel 3 Tier Trolley Cart 75x40x85. 20 Pc Weighing Scale 1 Kg. Digital Type: Digital Weighing Scale Body Shape: Rectangular Materials: Engineering Plastic And Stainless Steel Weighing Plate Capacity: 1 Kg Accuracy: 1 Gram Back Light Lcd Display With 15 Mm Minimum High Digits Weighing Units: Gram, Ounce, Pound Size: (l X W X H Mm ) 163 Mm X 245 Mm X 79 Mmm (minimum) 20 Set Weighing Scale 5kg. Type: Mechanical Weighing Scale Body Type: Circular Bowl Material: Stainless Steel Bowl And Metal Body (coated) Mechanism Type: Spring Lever Capacity: 5 Kg /11 Lb. Sensitivity/graduated By 10 Gm Measurement Units: Gram/kilogram Manual Setting On Zero, Must Be Accurate And Durable Calibrate The Scale Using The Adjustment Knob Preferably With A Packing Case Delivery Must Include Instruction Manual Written In Good English With Service Centers Located In The Major Cities In The Philippines Warranty Period Of 1 Year (parts And Service) Must Be Branded 40 Set Wire Skimmer Small, Type: Skimmer, Wire Mesh Body Shape: Round Material: Stainless Steel, Polished Overall Length: 40 Cm (minimum) Skimmer Head Diameter: 12 Cm (minimum) Diameter Of Holes: 2 Mm (approx.) Handle Has Hole For Hanging Preferably With A Packing Case Dishwashing Safe Must Be Branded. 40 Pc Wire Whisk Heavy Duty Type: Wire Whisk, Heavy Duty Body Shape: Ballon Material: Heavy Duty Stainless Steel Dimensions (l X W): 31.8 Cm X 7.6 Cm (minimum) Handle Length: 12 Cm (minimum) With Hanging Loop No. Of Wires: 8 Wires Wire Diameter: 2 Mm (minimum) Preferably With A Packing Case Dishwasher Safe Must Be Branded. 40 Pc Wire Whisk, Medium, Type Wire Whisk, Medium Body Shape: Ballon Material: Stainless Steel Wire Whisk Medium Dimensions (l X W): 25.4 Cm X 7 Cm (minimum) Handle Length: 10 Cm (minimum) With Hanging Loop No. Of Wires: 6 Wires Wire Diameter: 1.8 Mm (minimum) Preferably With A Packing Case Dishwasher Safe Must Be Branded. 40 Pc Wire Whisk,small, Type: Wire Whisk, Small Body Shape: Baloon Material: Stainless Steel Wire Whisk Medium Dimensions (l X W): 20.3 Cm X 6 Cm (minimum) Handle Length: 10 Cm (minimum) With Hanging Loop No. Of Wires: 6 Wires Wire Diameter: 1.8 Mm (minimum) Preferably With A Packing Case Dishwasher Safe Must Be Branded. 18 Pc Wok,medium Type: Wok, Medium Body Shape:round Material: Carbon Steel Thickness: 1.8 Mm Thick (minimum) Dimensions (dia. X H): 45 Cm X 14 Cm (minimum) Handle Material: Steel Riveted Convenient Both Side Handle 10 Cm (minimum) With Flat Bottom Preferably With A Packing Case Dishwashing Safe Must Be Branded 18 Pc Wok,small Type: Wok, Small Body Shape: Round Material: Carbon Steel Thickness: 1.5 Mm Thick (minimum) Dimensions (dia. X H): 36 Cm X 10 Cm (minimum) Handle Material: Steel Riveted Convenient Both Side Handle 8 Cm (minimum) With Flat Bottom Preferably With A Packing Case Dishwashing Safe Must Be Branded 12 Pc Working Table, Stainless, 4 Seaters Stainless Working Table , Two Layer (120x60x80) 30 Pc Zester, Type: Cheese Zester Body Shape: Standard Material: Stainless Steel Grating Surface Dimensions (l X W): 20.3 Cm X 4 Cm (minimum) Overall Length: 32.5 Cm (minimum) Handle Material: Plastic (polypropylene) Ergonomic Handle Preferably With A Packing Case Dishwasher Safe The Plastic Material Used Must Be Non-toxic Must Be Branded. Lot 6. Sumirap National High School (housekeeping Nc Ii)-php 326,452.00 1 Pc Alarm Clock Alarm Clock, Digital, Overall Dimensions: 13.5 X 8 X 4.5 Cm (approx.) Material: Plastic (pe/abs) Illuminated Lcd Digital Display: Time (12/24), Calendar (mm/dd), Temperature, Alarm Status (on/off), Snooze Display Size: 10 X 5 Cm (minimum), Time Can Be Read 30 Ft Day Time. Runs On Aaa Battery Which Come Together With The Item Smooth Surface, No Sharp Edges, Includes User's Manual Which Contains Operation Procedure, Name Of Parts, Safety Precautions, Trouble Shooting) 25 Pc Apron, Polyester-cotton (bib Apron, Sleeveless Adjustable Neck Loop Material : Polyester - Cotton Fabric Dimension : 70 To 60 Cm (minimum) With 2 Or 3 Pockets Uni-color, Dark No Sharp Edges And Loose Threads) 5 Pc Baskets, Laundry (3 - Bag Laundry Sorter, With Wheels Bag: Polyester, Rectangular Shape, Detachable From Frame With Metal Handle And Hanging Hook Bag Dimensions : Rectangular 22 X 15 X 8 Inch (minimum) Frame Material : Corrosion Resistant Steel, Sturdy No Wobble Frame Overall Dimensions : Rectangular, 31 X 30 X15 Inch (minimum) With Four Casters, 2 Inch Diameter (minimum) Smooth Surface, No Sharp Edges) 1 Set Bed, Queen (bed Set, Queen Size (60 X 75 Inch) Rectangular 1) Frame: Knock-down Type, All Steel, Powder Coated Including Head Board, Bare Weight: 20 Kg (minimum) No Wobble And Noise 2) Comes With Fabric Covered Foam 6 Inches Thick Foam Density: 29 -33 Kg/cu.m. 3) No Sharp Edges) 1 Set Bed, Single (bed, Single Size (w36 X L75 Inch) Rectangular 1) Frame: Knock-down Type, All Steel, Powder Coated Including Head Board, Bare Weight: 13 Kg (minimum) No Wobble And Noise 2) Comes With Fabric Covered Foam 6 Inches Thick Foam Density: 29 -33 Kg/cu.m. 3) No Sharp Edges) 10 Pc Board, Ironing (type: Foldable Type Ironing Board Body Shape : Standard Material : 25 Mm Tubing Approx., 0.8 Mm Thickness Board Size: 32 Inches (minimum ) Body Size :120 Cm X 30 Cm X 5 Cm Color : Any Comes With Box No Sharp Edges) 25 Pair Boots, Safety, Plastic (upper Material: Elastic Pvc Sizes: 7 Inches - 5pcs 8 Inches - 5pcs 9 Inches - 5pcs 10 Inches -5pcs 11 Inches - 5pcs Height: 13 To 14 Inches Plain Toe Type Of Boots: Unisex Rain Boots With Rugged Tractor Lug Outsole Packed With Carton Box Per Size) 15 Pc Brushes, For Housekeeping (brush, Floor Scrubbing, Angled Long Handle Bristle Material : Plastic, Stiff Handle Material : Metal Tubular Corrosion Reistant, Overall Length : 120 Cm. (minimum) Bristle Length : 5 Cm (=/- 1cm) Scrubbing Surface : 25 X 6 Cm (+/-1 Cm) No Sharp Edges) 10 Pc Buckets, Water (water Bucket Bucket Material : Hard Plastic, Round Body Capacity : 10 To 12 Liters Handle Material : Steel Smooth And Glossy Surface, No Sharp Edges) 10 Pc Caddy, Toilet (carrying Caddy For Toilet Cleaning Supplies Holds Spray Bottles And Other Cleaning Supplies, No. Of Compartments: 3 (minimum) Material :plastic Tray Depth: 11 Cm (approx.) Overall Dimension: 36 X 26 Cm (approx.) Smooth Surface, No Sharp Edges) 1 Unit Carpet Sweeper (carpet Sweeper, Cordless Electric Motorized Single Brush Roll (removable) Body Material : Hard Plastic ,(abs) Or Its Equivalent, Any Color Equipped With Rechargeable Battery (16 Minutes Run Time On Carpet), Removable Dirt Box Sweep Width : 8 Inches (minimum) Capacity (volume) : 0.35 Lit.(minimum) Handle: Metal, Powder- Coated, With Plastic/rubber Grip, Swivel Steering Assembled Height: 44 Inches (minimum) Comes With Battery Charger 220/240vac, 50/60hz With Plug To Adapt Type A Outlet (or Providing 3a Minimum Plug Adapter Is An Option) No Sharp Edges Includes User's Manual Which Contains Operation Procedure, Name Of Parts, Safety Precautions, Trouble Shooting.) 1 Unit Cart, For Housekeeping Nc Ii (housekeeping Cart Trolley, Equipped With Three-shelves With Steel/laminated Panels Single Door, Top Layer With Divider, Bag Holder, And 4 Wheels. Cart Frame: Steel, Powder Coated. Wheels: 2non-swivel 2 Swivel, 6 Inch Diameter, Non-markings. Overall Dimensions : Rectangular 90 X 48 X 1010 Cm (minimum) Comes With Accessory Linen Bag Smooth Surface, No Sharp Edges) 50 Pc Cleaning Cloth, Linth-free (lint Free Cleaning Cloths Material : Cotton Dimensions : Rectangular 16 X 26 Inch) 1 Unit Coffee Maker (coffee Maker, Electric Material: Metal, Plastic, Glass. Capacity: 6 Cups (minimum). Detachable Tank, With Water Level Indicator. Non-stick Warming Plate : Removable And Washable Filter Non-drip Valve : Lighted On/off Switch Power Supply: 220 V -240 V Ac 50/60 Hz , 500w Minimum Comes With A Heat Resistant Glass Pitcher. With A 1 Meter (minimum) Power Cord, Molded Male Plug To Adapt Type A Outlet (or Providing 5a Minimum Plug Adapter Is An Option). Smooth Surface, No Sharp Edges With Dti-bps Certification, Brand And Electrical Ratings Clearly And Permanently Mark On The Item. Comes With English Manual That Contains: Users Guide, List Of Parts, Maintenance Guide, Safety Guide. 1 Year Warranty Parts And Service With Service Centers Located In Major Cities In The Philippines) 5 Pc Dust Pan (dust Pan, Upright Standing Material: Plastic Overall Length: 65 Cm (minimum) Pan: Round Back, 24 X 26 X 9 Cm (minimum) Smooth Surface, No Sharp Edges) 5 Pc Duster, Anti-static (anti-static Duster Duster Material : Polypropylene Micro Fiber Duster: Length : 30 Cm (minimum), Overall Length: 50 Cm (minimum) Handle Material : Hard Plastic, No Sharp Edges) 7 Unit Fan, Electric ( Stand Fan, Electric Material: Metal, Plastic Size/diameter: 18 Inches Power Rating: 70 Watts (minimum), 220 / 240 Vac, 50 / 60 Hz, Single Phase Rotation Angle: 90 Degrees Base: Stable, 16 Inches Diameter (approx.) Removable Metal Guard On Front And Rear 3-speed Settings Comes With 1.5 Meters Power Cord And With Molded Male Plug To Adapt Type A Outlet (or Providing 3a Minimum Plug Adapter Is An Option) Smooth Surface, No Sharp Edges Includes User's Manual In English Which Contains: A. A Diagram Of The Parts With Their Names, B. Operating Procedures On How To Use The Equipment, C. Safety Precautions When Using The Equipment, D. Basic Troubleshooting And Maintenance Procedures With Dti-bps Certification, Brand And Electrical Ratings Clearly And Permanently Mark On The Item 1 Year Warranty Parts And Service) 3 Pc Fire Extinguisher(with Contents) (1.for Type A, B, C Fire: Dry Chemicals (monoammonium Phosphate) 2.portable Type 3.capacity : 5 - 6 Kgs 4.rechargeable Cylinder Metal 5.working Pressure Of Cylinder : 400 Psi 6.brass Valve With Pressure Gage 7.with Rubberized Hose And Aluminum Nozzle Attached 8.with Squeeze Lever To Discharge And Safety Pin 10.painted With Metal Primer And Red Enamel Paint 11.includes With User's Guide In English That Contains: A. Operating Procedure On How To Use The Equipment B. Safety Precaution When Using The Equipment 12.1 Year Warranty Parts And Service 13.the Item Must Be Branded And Have Good Quality) 10 Pc Flashlight (flashlight Led 1,000 Lumens (minimum), Color : White , Battery: Rechargeable, At Least 3,500 Mah , Can Be Used Also With 3 X Aaa Batteries; Body: Aluminum Alloy, No Sharp Edges Dimensions : 5 Inches X 1 Inch Diameter (minimum) Operating Duration Of Battery When Fully Charged : At Least 2 Hours; Includes 220/240vac, 50/60hz Power Adapter /charger And User's Manual In English Which Includes: A. A Diagram Of The Parts With Their Names, B. Operating Procedures On How To Use The Equipment, C. Safety Precautions When Using The Equipment, D. Basic Troubleshooting And Maintenance Procedures Branded, With 1 Year Warranty 10 Pc Flat Iron (clothes Flat Iron, Electric Material : Metal /plasic Body, Heat-resistant Plastic Handle, Aluminum Sole Overall Dimension : (l X W X H) 25 Cm X 12 Cm X 12 Cm (minimum) Power Rating : 220/240 Vac, 50/60 Hz; 1000 Watts (minimum) Equipped With Light Indicator, Variable Temperature Control, Overheat Protection, Power Cord And Plug To Adapt Type A Outlet (or Providing 10a Plug Adapter Is An Option) Smooth Surface, No Sharp Edges, Comes With English Manual That Contains : Users Guide, List Of Parts, Maintenance Guide, Safety Guide. The Item Must Be Branded, With Dti-bps Certification 1 Year Warranty Parts And Service With Service Centers Located In Major Cities In The Philippines.) 10 Pc Foam, Scrubbing (1. Material: Cellulose And A Scouring Pad On One Side 2. Dimension: Length : 140 - 180 Mm ; Width : 80 - 100 Mm ; Thickness : 12 - 20 Mm 3. The Item Must Be Of Good Quality) 4 Pc Garbage Receptacles (1.bucket / Tub Material : Hard Plastic, (ps) Polystyrene 2.bucket / Tub Color : Any Color 3.capacity (gallons) : 3 Gal. (minimum) Comes With A Cover 4.the Item Must Have Good Quality) 30 Pair Gloves, Rubber (1.heavy-duty Latex-free Vinyl Rubber Gloves 2.thickness : 4 Mil 3.color : Any Color 4.size : Medium 5.other Features: Acid/solvent Resistant. 6.the Item Must Be Of Good Quality) 15 Pc Goggles, Safety (safety Goggles, Clear Polycarbonate - One Piece Lens With 180° Panoramic View, Non-fog Size/dimension: L 17 - 18.5 Cm X W 8 Cm X D 5-7.5 Cm High Impact Resistant, Ansi "z87" Compliant Firm And Comfortable Seal Around Forehead, Cheeks, Nose And Temples Protects Against Splash, Chemicals, Dust Adjustable Head Strap Shall Bear Mark Z87 Embossed Or Engraved Or Etched On The Item. Smooth Surface, No Sharp Edges) 1 Pc Hairdryer( Electric Hairdryer, With Concentrator Nozzle Two Heat Setting And 1 Speed (minimum) Rating : 220/240 Vac, 1200 W (minimum) Body Length Including Nozzle: 20 Cm Folding Handle Design, With Hanging Ring Smooth Surface, No Sharp Edges Branded, Brand Name And Electric Rating Permanently Mark On The Item, With Dti-bps Certification With User's Manual Written In English That Contains Operating Procedure, Parts With Description, Safety Procedure, And Maintenance. With Service Centers Located In Major Cities In The Philippines. 1 Year Warranty(parts & Service) 2 Roll Hose, Water(water Hose Material: Pvc Fiber Reinforced, Three (3) Layers; Any Color; Hose Length: 50 Feet; Hose Diameter: 5/8 Inches; Pressure Capacity: 200 Pounds Per Square Inch (minimum); Fitted With Male And Female Brass Couplers (nh, 11.5 Tpi) For Spray Nozzle No Sharp Edges) 3 Pc Kettle, Electric(electric Kettle Cordless (with Pouring Spout), Hinged Lid, Detachable From And Can Rotate On Its Corded Base Material : Round Stainless Body, Plastic Handle, Lid And Base Capacity : 1.5 To 2 Liter Automatic Shut - Off, With Power Indicator Light Power Rating: 220//240vac, 50/60hz, 1000 -1600 Watts Base With A 50 Cm (minimum) Power Cord, Molded Male Plug To Adapt Type A Outlet (or Providing 10a Plug Adapter Is An Option) Smooth Surface, No Sharp Edges; Dti-bps Certified Comes With English Manual That Contains: Operation Procedure, Maintenance And Safety Guide. The Item Must Be Branded, Brand Name And Electrical Ratings Permanently Mark On The Item.) 5 Pc Laundry Sorter(3 - Bag Laundry Sorter, With Wheels Bag: Polyester, Rectangular Shape, Detachable From Frame With Metal Handle And Hanging Hook Bag Dimensions : Rectangular 22 X 15 X 8 Inch (minimum) Frame Material : Corrosion Resistant Steel, Sturdy No Wobble Frame Overall Dimensions : Rectangular, 31 X 30 X15 Inch (minimum) With Four Casters, 2 Inch Diameter (minimum) Smooth Surface, No Sharp Edges) 2 Pc Light, Emergency(emergency Light, 2 Heads Led Materials: Metal, Anti-rust Coated Duration Time (2 Heads): 5 Hours (minimum) Automatically Light Up During Power Outage Overcharge And Over- Discharge Protection Built - In Ac Charger, Power Cord Plug To Adapt Type A Outlet (or Providing 5a Minimum Plug Adapter Is An Option) Battery Test Switch - External Safety Fuse Head: White Led 1w (minimum) 3.5 " Dome Reflector Power Rating: 220 -240 Vac , 50/60 Hz 20-24 Hours Charge Time Dimensions: Rectangular 27 X 7 X 27 Cm (approx.) Sooth Surface, No Sharp Edges Includes User's Manual In English Which Contains: A. A Diagram Of The Parts With Their Names, B. Operating Procedures On How To Use The Equipment, C. Safety Precautions When Using The Equipment, D. Basic Troubleshooting And Maintenance Procedures The Item Must Be Branded, Brand Name And Electrical Ratings Permanently Mark On The Item.) 2 Pc Mirror Wall Mirror With Frame Flat Glass Mirror, 2 Mm Thick (minimum), Clear With No Distortion Frame: Wood Or Plastic Commercial Finish Rectangular Shape, 3600 Sq.cm (minimum) Includes Mounting Accessories Smooth Surface, No Sharp Edges) 20 Pc Mop (mop, Handle And Mop Head Set, Refillable Head Handle: Aluminum Or Anti-rust Coated Steel, With Hard/stiff Plastic Mop Head Holder, Clip Type With Tightening Knob Overall Handle Dimension: 130 X 19 Cm (minimum) Mop Head: Cotton Thread/yarn, Sewn Tailband, L 34 X 16 X 4 Cm (minimum), White Handle: Plated Steel Tube Or Wood, Length : 40 (minimum), No Sharp Edges 1 Set Polisher, Floor, Electric, With Accessories(electric Floor Polisher With Accessories Material: Stainless Steel, Aluminum Alloy Handle: Stainless Tube, Adjustable Height 1 Meter Long (approximate), With Dual Switch Lever Size/capacity :13 Inch (minimum) Diameter Power Supply: 220/240 Vac, 50/60 Hz. Power: 1/3 Hp (minimum) Rotation Speed : 160 Rpm (minimum) Heavy Duty (royal) Power Cord Length : 12 Meters (minimum) With Type A Plug (or Providing 10a Plug Adapter Is An Option) With Pair Of Rubber Wheels, Smooth Surface, No Sharp Edges Comes With Pad Holder, 2 Pcs - Polishing Brush And 3 Pcs - Floor Polishing Pads Includes User's Manual In English Which Contains: A. A Diagram Of The Parts With Their Names, B. Operating Procedures On How To Use The Equipment, C. Safety Precautions When Using The Equipment, D. Basic Troubleshooting And Maintenance Procedures Branded, Brand Name And Electric Rating Permanently Mark On The Item, With 1 Year Warranty Parts And Service The Offered Brand Of The Item Must Be An International Brand With At Least 5 Years Presence At The Local Market And Global Presence In The Usa, Europe Or In Japan Market.) 5 Pc Shelving(shelving, Open, Knockdown Type, Adjustable Shelves Metal Powder Coated Frame Number Of Shelves : 5 Overall Dimensions : 85 X 30 X 180 Cm(minimum) Sturdy Connection, No Wobble Smooth Surface, No Sharp Edges) 5 Pc Sign, Caution(caution Sign, A Shape-2 Panel Self Standing, With D-handle, Collapsible For Easy Storage Material : High Impact Plastic, Panel Dimension : Rectangular (lxw) 55-65 Cm X 25 X 61 0m (minimum), Panel Depth : 2 Cm (minimum) Color : Yellow Print Description : "caution: Wet Floor" On One Side "cleaning In Progress On The Other Side, Both Messages Provided With Graphics Printed In Black. Font Size: 100 -120 Mm X 50 -70 Mm, Arial Smooth Surface, No Sharp Edges) 10 Pc Sponges, Dish(dish Sponge, Cellulose, Non-scratch Dimensions : 5 X 3 X 1 Inch (minimum) Branded) 10 Pc Spray Gun, Water(barber/salon Spray Gun Material: Hdpe Transparent Plastic Capacity: 300 Ml.(minimum) Trigger Type Sprayer Dimension: Diameter :7 Cm. X Height: 16.3 Cm (minimum) Rotating Nozzle To Adjust Spray Patterns Smooth Surface, No Sharp Edges Must Be Branded) 10 Pc Squeegee(squeegee, Short Handle Head/blade Material: Stainless, Rubber Handle: Plastic Or Stainless Steel Blade Length: 25 - 30 Cm Overall Length (handle And Head) 20 - 32 Cm No Sharp Edges ) 5 Pc Squeezer, Mop(mop Bucket With Squeezer/wringer And Wheels Hand Lever To Squeeze, Made Of Metal, With Hand Grip Material : Hard Plastic, (ps) Polystyrene Or Its Equivalent Capacity : 30 L (minimum) Overall Dimension (excluding Handle: ( L X W X H ) 40 X 27 X 57 Cm (minimum) Color : Yellow With 3 Inches Non-marking Rubber Casters "caution" Printed In Black On Both Sides Of The Mop Bucket Smooth Surface, No Sharp Edges) 1 Pc Step Ladder(material: Aluminum U Channel Capacity: 250 Lbs (minimum) Type: Flatform Type Number Of Step: 6 (including Top Step) Reach Height: 6 To 8 Feet(minimum) Width: 15 Inches Minimum Spread: 4 Feet (minimum) Twin Steps With Gripped Treads To Prevent Slipping Step Braces On Top And Bottom Step Heavy Duty Aluminum Foot Bracket With Slip-resistant Foot Pad With User's Manual In English Which Includes: A. Parts Manual With Labels, B. Assembly Instructions, Brandedfeet(minimum) Width: 15 Inches Minimum Spread: 4 Feet (minimum)) 2 Pc Vacuum Cleaner, Dry And Wet(electric Vacuum Cleaner, Wet And Dry Function, Sucks Even Screws, With 4 Swivel Caster Wheels Material : Hard Plastic, (abs) Or Rust Proof Body Equivalent Power Supply : 220/240vac, 50/60hz, 1000 Watts (minimum) Auto Shut Off Tank Capacity : 20 Liters (minimum) Equipped With Complete Accessories I.e., Detachable Vacuum Hose Assembly (flexible Non-kink), Extension Tubes/wands, Carpet (long Square) Brush Nozzle, Wet And Dry Floor Brush Nozzle, Crevice Nozzle, Hepa Filter, Sponge Filter/washable Cloth Bag. Comes With 4 Meters (minimum) Heavy Duty (royal) Power Cord, Molded Male Plug To Adapt Type A Outlet (or Providing 10a Plug Adapter Is An Option) Smooth Surface, No Sharp Edges With User's Manual Written In English That Contains Operating Procedure, Parts With Description, Safety Procedure, And Maintenance. The Item Must Be Branded, Brand Name And Electric Rating Permanently Mark On The Item. 1 Year Warranty Parts And Service With Service Centers Located In Major Cities In The Philippines. The Offered Brand Of The Item Must Be An International Brand With At Least 5 Years Presence At The Local Market And Global Presence In The Usa, Europe Or In Japan Market.) 1 Unit Washer, Laundry(1. Front Load Electric Washer, Laundry 2. Electronic Control, Digital Indicator Display , Transparent Glass Door 3. Body Material : Steel, Powder Coated, Any Color 4. Dimensions (wxdxh): 590 Mm (minimum) X 490 Mm (minimum) X 820 Mm (minimum) 5. Drum Material : Stainless Steel 6. Capacity : 8 Kg (minimum) 7. Spin Speed : 1200 Rpm (minimum) 8. Power Rating: 220 /240vac, 50/60 Hz. 9. Comes With A 1 Meter (minimum) Heavy Duty Power Cord With Male Plug To Adapt Type A Outlet (or Providing 20a Plug Adapter Is An Option) 10. Smooth Surface, No Sharp Edges 11. With Dti-bps Certification, Brand And Electrical Ratings Clearly And Permanently Mark On The Item 9.includes User's Manual In English Which Contains: A. A Diagram Of The Parts With Their Names, B. Operating Procedures On How To Use The Equipment, C. Safety Precautions When Using The Equipment, D. Basic Troubleshooting And Maintenance Procedures 12.the Item Must Be Branded, Dti-bps Certified, 1 Year Warranty Parts And Service 13. With Service Centers Located In Major Cities In The Philippines. 14.the Offered Brand Of The Item Must Be An International Brand With At Least 5 Years Presence At The Local Market And Global Presence In The Usa, Europe Or In Japan Market.) 2 Pc White Board(white Board, Floor Standing, Rolling Board: White Formica Laminated, Plane Will Not Deform. Board Size: Rectangular 1800mm W X 1000 To 1200mm H, Board Edges Secured With Aluminum Clip Edging 17 Mm (minimum) Wih Plastic Corner Caps Comes With Metal Tray For Marker And Eraser The Stand And Frame Are Constructed With Aluminum Or Powder Coated Steel 25mm Square Tube (minimum), Sturdy, No Wobble With 4 Lockable Hard Plastic Caster Wheels Overall Height From Floor: 210 To 214cm Smooth Surface, No Sharp Edges) Lot 7. Tangub City National High School (food And Beverage Services Nc Ii) Php 571,245.00 50 Pcs Chair, Dining Type : Dining Side Chair Body Shape: Square Material : Metal (round Or Square) Dimesion: Total Height - 33" X 15" X15" (minimum) Capacity: 150 Kg. Black Colored Powder Coated Frame With Foam On Seat Packed In Carton Box The Item Must Have Good Quality 4 Pcs Coffee Pot, 2 Pints Type: Manual Drip Body Shape: Round Material : Stainless Steel With Cover Capacity : 2 Pints Outside Diameter : 90 -110 Mm Over-all Height : 200 - 230 Mm Thickness : 0.5 - 1 Mm With Handle And Spout Packed In Carton Box The Item Must Have Good Quality 6 Pcs Container, Creamer Design: Type: Porcelain With Spout Body Shape: Circular Material: Porcelain Diameter : 50 - 65 Mm Height : 80 - 105 Mm Color : White Appearance : Glossy White Packed In Carton Box The Item Must Have Good Quality 24 Set Cups Ans Saucers 5-6 Oz. 1. Material : Porcelain 2. Capacity : 5 Oz./140 Ml 3. Heatproof Up To 300 Deg. C 4. Color : White 5. The Item Must Be Of Good Quality 6. Packed In Carton Box 10 Pcs Folder, Menu Type: Leather Menu Folder Body Shape: Rectangular Material: Leather With 2 Partitions And 6 Inserts Size: 31.5cm X 24.5cm Color: Brown/black Applicable Paper Size: A4 50 Pcs Fork, Cocktail 1. Material/appearance: Stainless Steel, Highly Polished, W/ Plain Design 2. Type : Rounded Tip Handle 3. Over-all Length : 110 - 165 Mm 4. Width : 20 - 30 Mm (minimum) 5. Handle Thickness : 2 Mm To 4 Mm 6. Handle Length : 75 - 90 Mm 7. Small, 8. Color : Silver 9. The Item Must Be Branded And Have Good Quality. 50 Pcs Fork, Dessert Type : Dessert Fork Body Shape: Fork Shape, Round Tip Material/appearance : Stainless Steel, Highly Polished,with Plain Design, Rounded Tip Handle Length : 150 Mm - 175 Mmwidth : 20 - 30 Mmhandle Thickness : 1.5 Mm - 3 Mm Number Of Tines : 4 Handle : 130 Mm (minimum) Color : Silver Packed In Plastic Pouch The Item Must Be Of Good Quality 60 Pcs Fork, Dinner Type: Dinner Fork Body Shape: Fork Shape Material / Appearance : Stainless Steel, Highly Polished, With 4 Tines Over - All Length : 120 - 175 Mm Thickness Of Handle : 2 - 3 Mm Color : Silver Packed In Plastic Pouch The Item Must Be Of Good Quality 36 Pcs Fork, Fish Type : Fish Fork Body Shape: Fork Shape With Round Tip Material / Appearance : Stainless Steel, Highly Polished, With Plain Design Over-all Length : 180 - 215 Mm Fork Width : 1.5 Mm - 3 Mm Fork Thickness : 1 Mm - 2 Mm Number Of Tines : 4 Length Handle : 120 - 130 Mmhandle Thickness : 2 Mm - 3 Mm Color : Silver Packed In Plastic Pouch The Item Must Be Of Good Quality 36 Pcs Fork, Oyster Type: Oyster Fork Body Shape: Fork Shape Material: Stainless Steel, With High Polish Appearance, And With Plain Design Length: 90 - 120 Mm Thickness: 1 Mm - 3 Mm Silver Color With Three Short Wide Curved Tines Packed In Plastic Pouch The Item Must Be Of Good Quality 24 Pcs Glass, Champagne Flute Type : Flute Glass Body Shape: Round Material: Clear Crystal Glass Dimension : Height: 20 -24 Cm, Top Diameter: 50 -70 Mm, Bottom Diameter: 60 - 80 Mm Capacity: 250 Ml. (minimum) Thickness: 1.5 - 3 Mm Packed In Carton Box The Item Must Have Good Quality 36 Pcs Glass, Collins Type: Tumbler Body Shape: Round Material : Clear Glass Capacity : 10 Oz To 14 Oz Thickness : 1.5 -3 Mm (minimum) Packed In Carton Box The Item Must Have Good Quality 36 Pcs Glass, Juice/hi-ball 1. Material : Clear Glass 2. Type : Hi-ball 3. Height : 140 - 160 Mm 4. Bottom Diameter : 50 -70 Mm 5. Top Diameter : 50 - 70 Mm 6. Thickness : 2 - 4 (minimum) 7. Capacity : 8 Oz. To 10 Oz. 8. Diswasher Safe 9. The Item Must Be Branded And Good Quality 10. Packed In Carton Box 36 Pcs Glass ,pilsner(ice Tea Glass) Type:falired Rim,body Shape:round Slender Bowl,material:clear Glass Capacity:20 0z To 23 Oz With Flaired Rimand Slender Shape Packed In Carton Box.the Item Must Have Good Quality. 36 Pcs Glass, Red Wine Type: Royalty Body Shape: Balloon Shaped Bowl Material: Crystal Clear Glass Rim Diameter : 55 - 60 Mm Thickness : 1.5 Mm - 3 Mm Over - All Length : 200 -220 Mm Capacity : 250 -300 Ml Stem Diameter : 6 - 8 Mm Stem Length : 85 - 90 Mm Base Diameter : 75 - 85 Mm Base Thickness : 2 - 4 Mm 40 Pcs Glass, White Wine Type: Royalty Body Shape: Balloon Shaped Bowl Material: Crystal Clear Glass Rim Diameter : 55 - 60 Mm Thickness : 1.5 - 3 Mm Over -all Length : 200 -220 Mm Capacity : 270 - 300 Ml Stem Diameter : 6 - 8 Mm Stem Length : 75 - 85 Mm Base Diameter : 70 - 80 Mm Base Thickness : 2 - 5 Mm 4 Pcs Gravy Boats Type: Steel Type Body Shape: Boat Shape With Handle Material: Stainless Steel Capacity : 5 Oz. Appearance: Mirror Polish Finish Size :17cm X 7.3cm X 8.2 Cm / 6.7 X 2.9 X 3.2 Inches (minimum) The Item Must Have Good Quality Packed In Plastic Pouch 4 Pcs Ice Bucket, 2 Liters With Tongs Type: Steel Type Body Shape: Circular Set Includes: A. Ice Bucket Material : Stainless Steel Diameter : 140 - 180 Mm Height : 140 - 170 Mm Thickness Of Bucket : 0.7 - 2 Mm Capacity : 2 Liters (minimum) The Item Must Have Good Quality 24 Pcs Knife, Butter 1. Material : Stainless Steel W/ Highly Polished Appearance 2. Over-all Length : 140 Mm - 150 Mm 3. Handle Thickness : 3 Mm - 5 Mm 4. With Dull Edge And Rounded Tip 5. The Item Must Have Good Quality. 6. Packed In Carton Box 24 Pcs Knife, Dinner Type: Dinner Knife Body Shape: Flat With Round Tip Material / Appearance : Stainless Steel Blade Highly Polished Handle Material : Stainless Steel Overall Length : 160 - 190 Mm Blade Thickness : 2 - 4 Mmhandle Thickness : 3 - 6 Mm Serrated Blade With Rounded Tip Packed In Carton Box The Item Must Have Good Quality 24 Pcs Knife, Fish Type : Fish Knife Body Shape: Flat With Pointed Tip Material / Appearance : Stainless Steel, Highly Polished W/ Plain Design Overall Length : 200 - 220 Mm Width Blade : 20 - 25 Mm Thickness Of Blade : 2 Mm - 4 Mm Thickness Of Handle: 3 Mm - 6 Mm Wide Blade, Dull Edge, Tip Made With A Notched Point Color : Silver Packed In Carton Box The Item Must Have Good Quality 20 Pcs Napkin Holder (stainless) Type: Steel Type Body Shape: Rectangular Material : Stainless Steel With Highly Polished Appearance Dimension : Width : 70 - 90 Mm X Length : 150 - 170 Mm , Thickness : 0.7 Mm -2 Mm Packed In Plastic Pouch The Item Must Have Good Quality 20 Pcs Order Pads Type: Numbered Pads Body Shape: Rectangular Material : 80 Gsm Offset Paper Each Pad Comes With A 100 Sheets And Corresponding Copy Page Each Pad Has Sequentially Numbered Orders To Make It Easy To Keep Track With 100 Sheets Per Pad And 10 Pads Included Can Take 1000 Orders Before You Run Out Packed In A Plastic Pouch 12 Pc Pepper And Salt Mill Type: Pepper & Salt Mill Body Shape: Round Body Material: Wood Size: Diameter: 5 Cm X Height: 20 Cm (minimum) Carved Of Wood With Stainless Steel Grinding Mechanism Color: Natural Screw Cap At The Top Of The Mill To Adjust The Thickness Of Peeper Or Spices Preferably With A Packing Case Food Grade And Nontoxic Must Be Branded 50 Pc Plate Covers Type: Steel Type Body Shape: Circular Material: Stainless Steel, Mirror Polished Diameter: 10 1/4 Inches (minimum) Height: 2 7/8 Inches (minimum) Thickness: 1/16 Inch. (minimum) With Handle Packed In Plastic Pouch The Item Must Have Good Quality 50 Pc Plate, Dessert, 7" To 8" Type: Plain Type Body Shape: Circular Material: Porcelain Supply Must Be A Set, Consisting Of One (1) Of Each: 7 Inches And 8 Inches Plates Color : White Inner Diameter: 145 To 165 Mm Thickness : 3 To 6 Mm Smooth And Glossy Surfaces Packed In Carton Box The Item Must Have Good Quality 60 Pc Plate, Dinner, 10" Type: Plain Type Body Shape: Circular Material: Porcelain With No Design Color: White Inner Diameter : 200 Mm - 215 Mm Outer Diameter : 250 - 260 Mm Thickness : 3 Mm - 6 Mm Smooth And Glossy Surfaces Packed In Carton Box The Item Must Have Good Quality 50 Pcs Plate, Fish, 8" To 9" Type: Plain Type Body Shape: Circular Material : Porcelain With No Design Supply Shall Be A Set Consisting Of: One (1) Each 8 Inches And One (1) Each, 9 Inches Color : White Inner Diameter : 165 Mm - 190 Mm (minimum) Thickness : 3 Mm - 6 Mm Smooth And Glossy Surfaces Packed In Carton Box The Item Must Have Good Quality 10 Pcs Round Table (8's) Type: Foldable Body Shape: Round Material: High Density Polyethylene Table Top Powder Coated Steel Frame Size: 154cm X 74cm X4.5cm (minimum) Good For 8 To 10 Seater Capacity Tube Size : 28 Mm Diameter X 1 Mm Thickness Packed In A Carton Box The Item Must Have Good Quality 50 Pcs Salad Forks Type: Salad Fork Body Shape: Fork Shape Material/appearance: Stainless Steel, Highly Polished, With 4 Tines Length: 150 Mm - 175 Mm Thickness Of Handle : 2 Mm - 3 Mm Color: Silver Packed In Plastic Pouch The Item Must Be Of Good Quality 50 Pcs Salad Knife Type: Salad Knife Body Shape: Semi Rectangular Blade With Pointed Tip Material/appearance: Stainless Steel, Highly Polished, W/ Plain Design Overall Length: 145 -160 Mm Blade Thickness: 2 Mm To 4 Mm Handle Thickness: 4 Mm To 6 Mm Handle Material: Stainless Steel Rounded Tip Handle Packed In Carton Box The Item Must Have Good Quality 50 Pcs Salad Plates 7" To 8" Type: Plain Type Body Shape: Circular Material: Porcelain With No Design Supply Must Be A Set Consisting Of One (1) Each: 7 Inches And 8 Inches Plates Color: White Diameter (inner): 150 Mm - 165 Mm Thickness: 3 Mm - 6 Mm Smooth And Glossy Surfaces Packed In Carton Box The Item Must Have Good Quality 20 Pcs Salt And Pepper Shakers Type: Glass Type Body Shape: Square Material: Glass And Aluminum Over-all Height: 75 -90 Mm Length: 50 -60 Mm Width: 50 -60 Mm Aluminum Cover Packed In Carton Box The Item Must Have Good Quality 25 Pcs Sauce Laddles Type: Spouted Bowl Body Shape: Circular With Pouring Spout Material: Stainless Steel, Highly Polished Appearance Over-all Length: 220 -230 Mm Ladle Bowl Length: 60 -65 Mm Long Ladle Bowl Diameter: 65 -70 Mm Depth: 10 -15 Mm Handle Details: 150-155 Mm Long X 20 -30 Mm Wide X 2 - 4 Mm Thick Color: Silver With Hang Hole For Hanging And Easy Access Dishwasher Safe Packed In Plastic Pouch The Item Must Have Good Quality 50 Pcs Server, Cake 1. Material : Stainless Steel Blade , Highly Polished Appearance 2. Over-all Length : 220 To 270 Mm 3. Width : 60 - 80 Mm 4. Thickness : 1.5 Mm To 2 Mm 5. Handle : 120 -140 Mm Long, Non-toxic Plastic 6. Shape : Shovel-shaped 7. Color : Silver 8. The Item Must Have Good Quality 9. Packed In Carton Box 50 Pcs Service Forks Type : Service Fork Body Shape: Fork Shape Material/appearance: Stainless Steel, Highly Polished, W/ Palin Design Over-all Length: 220 Mm - 260 Mm Width: 20 - 25 Mm Handle Thickness: 1.5 Mm - 4 Mm Handle Length - 165 Mm - 185 Mm 4 Tines Color: Silver Packed In Plastic Pouch 25 Pcs Service Tray Type: Plastic Body Shape: Rectangular Material: Plastic (pp) Size : 14 Inches X 18 Inches X 1 Inch (minimum) Color : Any Packed In Plastic Pouch The Item Must Have Good Quality 25 Set Show/service/base Plates 11" To 14" Type: Plain Type Body Shape: Round Material: Porcelain With No Design Supply Must Be A Set Consisting (1) Of Each: - 11 Inches, - 12 Inches, - 13 Inches, And - 14 Inches Plates Color: White Diameter, Inner : 225 Mm - 250 Mm Thickness: 3 Mm - 6 Mm Smooth And Glossy Surfaces 50 Pcs Side Plates Or Bread Plates 6'' Type: Plain Type Body Shape: Round Material: Porcelain With No Design Color: White Inner Diameter: 95 Mm To 120 Mm Outer Diameter: 145 Mm To 170 Mm Thickness : 3 Mm - 6mm Smooth And Glossy Surfaces Packed In Carton Box The Item Must Have Good Quality 50 Pcs Side Towels Type: Chef's Towel Body Shape: Rectangular Material: Oxford Polyester Soft Cloth Over-all Length : 640 - 680 Mm Over-all Width : 420 -460 Mm Color : Plain White Packed In Plastic Pouch The Item Must Have Good Quality 25 Pcs Silver Platter Type: Steel Type Body Shape: Round Material: Stainless Steel Diameter: 300 -330 Mm Thickness: 1 - 2 Mm Packed In Plastic Pouch The Item Must Have Good Quality 50 Pc Soup Bowl Type: Plain With Two Handles Body Shape: Circular Material : Porcelain Capacity : 24 Oz. (minimum) Packed In Carton Box The Item Must Have Good Quality Packed In A Carton Box 25 Pc Soup Laddle Type: Steel Type Body Shape: Circular Material: Stainless Steel, Highly Polished Appearance Over-all Length : 220 -235 Mm Ladle Bowl Details : 60 -65 Mm Long, 60 -75 Mm Diameter, 10 -15 Mm Deep Handle Details : 145 - 155 Mm Long X 12 - 25 Mm Wide X 1.5 -3 Mm Thick Color : Silver With Hang Hole For Hanging And Easy Access 15 Pc Soup Tureen Type: Steel Body Shape: Round Material: Stainless Steel Capacity: 7 - 11 Quart Size : 60 X 35 X 32 Cm (minimum) Packed In Plastic Pouch The Item Must Have Good Quality 100 Pc Spoon, Dinner Type : Dessert Spoon Body Shape: Oval Material/appearance: Stainless Steel, Highly Polished With Plain Design Over-all Length : 175 To 190 Mm Thickness : 2 Mm - 3 Mm Shorter Handle : 120 -130 Mm Color : Silver Packed In Plastic Pouch The Item Must Have Good Quality 100 Pc Spoon, Dessert Type : Dessert Spoon Body Shape: Oval Material/appearance: Stainless Steel, Highly Polished With Plain Design Over-all Length : 175 To 190 Mm Thickness : 2 Mm - 3 Mm Shorter Handle : 120 -130 Mm Color : Silver Packed In Plastic Pouch The Item Must Have Good Quality 100 Pc Spoons, Service Type : Service Spoon Body Shape: Oval Material: Stainless Steel, Highly Polished, W/ Plain Design Over-all Length: 220 Mm - 250 Mm Width: 30 - 38 Mm Handle Thickness: 1.5 Mm - 4 Mm Handle Length - 165 Mm - 185 Mm Color: Silver Packed In Plastic Pouch The Item Must Have Good Quality 100 Pc Spoons, Soup (cream And Cosume) Type: Soup Spoon Body Shape: Round Material/appearance : Stainless Steel, Highly Polished, W/ Plain Design, Rounded Tip Handle Over-all Length : 165 Mm - 200 Mm Smaller Oval Shaped Spoon Bowl And Tapers Slightly To The Tip Shorter Handle : 110 Mm - 170 Mm Thickness : 1.5 Mm - 3 Mm Color : Silver Packed In Plastic Pouch 50 Pc Steak Knife Type: Steak Knife Body Shape: Flat With Serrated Edge Material: Stainless Steel Steel Blade With Wooden Handle Length: 170 Mm To 203 Mm Handle Wood Thickness: 10 - 14 Mm With Serrated Blade Packed In Carton Box The Item Must Have Good Quality 25 Pc Sugar Container Type: Glass Type Body Shape: Round Material: Glass With Brass Lid (or Equivalent) Diameter: 70 -80 Mm Height: 130 -140 Mm Capacity: 12 Oz. Packed In Carton Box The Item Must Have Good Quality 50 Pc Table Cloth, 54 X 54 Inches Type: Plain Cloth Body Shape: Square Material: Oxford Polyester Cloth Color: Plain White Dimension: L 54 Inches X W 54 Inches (minimum) Packed In Plastic Pouch The Item Must Have Good Quality 100 Pc Table Cloth, Rectangular Type: Plain Cloth Body Shape: Rectangle Material : Linen Size : 120cm X160cm (minimum) Color : Any Color But Not Black Feature: Washable Packed In A Plastic Pouch 100 Pc Table Napkins, Cloth, 16"x16" Type: Plain Cloth Body Shape: Square Material: Oxford Polyester Cloth Or Its Equivalent Size: L 16 Inches X W 16 Inches (minimum) Color: Plain White Packed In Plastic Pouch The Item Must Have Good Quality 80 Pcs Table Skirting Cloth 90" To 90" Type: Plain Cloth Body Shape: Square Material: American Cotton Twill Cloth Color: Any Color Except Black Dimension: 90 Inches X 90 Inches (minimum) Packed In Plastic Pouch The Item Must Have Good Quality 50 Pcs Table, Square/rectangular (4's Or 6's) Type: Foldable Plastic Body Shape: Square/rectangle Material: High Density Polyethylene Table Top Powder Coated Steel Frame Dimension: 37 - 39 X 37 - 39 Inches Color: White Good For 4 Persons Packed In Carton Box The Item Must Have Good Quality 20 Pcs Tea Pot, 2 Pints Type: Porcelain Type Body Shape: Round With Handle And Pouring Spout Material : Porcelain Capacity : (2 Pint) Color : White Packed In Carton Box The Item Must Be Of Good Quality 50 Pcs Teaspoon Type : Tea Spoon Body Shape: Oval Tip Material/appearance: Stainless Steel, Highly Polished, W/ Plain Design Over-all Length: 120 Mm To 140 Mm Handle Thickness: 2 Mm To 4 Mm Short Handle Length - 100 Mm (minimum) Color: Silver Packed In Plastic Pouch The Item Must Have Good Quality 15 Pcs Tong, 8 Inches Type: Tong, 8 Inches Body Shape: Standard Material: Stainless Steel Size: 8 Inches Stainless-steel Arms With Soft, Comfortable Grips Nylon Heads Safe For Nonstick Cookware Heat-resistant Up To 400 Degrees Fahrenheit Tongs Lock Closed For Storage Preferably With A Packing Case Food Grade And Dishwasher-safe Must Be Branded 30 Pcs Tooth Pick Holder Type: Steel Type Body Shape: Round Material: Stainless Steel, Highly Polished In Appearance Diameter: 30 -35 Mm Diameter (minimum) Height: 65 -75 Mm Capacity: 1.24 Oz. (minimum) Packed In Plastic Pouch The Item Must Have Good Quality 20 Pcs Tray Stand Type: Foldable Body Shape: Rectangular Material: Chrome Plated Metal Folding Tray Stand Length: 470 -490 Mm Width: 400 -440 Mm Height: 770 -790 Mm Packed In Plastic Pouch The Item Must Have Good Quality 30 Pcs Tray, Bill Folders/change 1. Material : Heavy Duty Plastic ( Abs ) Or Its Equivalent 2. Height : 190 - 220 Mm 3. Width : 120 -140 Mm 4. Thickness : 2 Mm To 3 Mm (minimum) 5. Color : Black 6. With Check And Pen Holder 7. The Item Must Have Good Quality 8. Packed In Plastic Pouch 20 Pcs Tray, Round (bar) Type: Plastic Body Shape: Round Material: ( Pe/abs) Plastic Rubberized Surface, Non-slip/grip Tight Over-all Diameter: 345 -360 Mm (minimum) Thickness: 2 - 4 Mm (minimum) Color: Black Packed In Plastic Pouch The Item Must Have Good Quality 50 Pcs Water Goblet Type: Water Goblet Body Shape: Balloon-shaped Bowl Material: Crystal Clear Glass Over-all Length: 200 -220 Mm Capacity: 270 Ml To 300 Ml Rim Diameter - 55 -65 Mm Thickness: 1 Mm To 3 Mm Stem Length : 75 -85 Mm Stem Diameter : 6 -8 Mm Base Thickness : 3 -4 Mm Base Diameter : 7 -80 Mm Packed In Carton Box The Item Must Have Good Quality 30 Pcs Water Pitcher (stainless) Type: Steel Type Body Shape: Circular Material: Stainless Steel, Highly Polished Appearance Height: 170 Mm To 220 Mm Top Diameter: 110 -120 Mm (approximate) Capacity: 1 - 1.5 Liter With Pour Spout Dishwasher Safe Packed In Plastic Pouch The Item Must Have Good Quality Lot 8. Tangub City National High School (front Office Services And Local Guiding Services) Php 232,832.00 50 Pcs Calculator Type: Simple Calculator, Non Scientific Body Material: Hard Plastic Minimum Size: 110mm Width X 140mm Long Lcd Display: At Least Font Size Is 8mm X 5mm With Dual Power; Solar Cell And Battery With At Least 8 Digits Display Includes Spare Battery Packed With Protective Carton Box User's Manual In English Which Includes: A. Parts Manual With Labels, B. Assembly Instructions C. Operating Procedures On How To Use The Equipment, 1 Pcs Cart, Bell Boy Type:hotel Luggage Trolley Capacity: At Least 450 Kilograms Minimum Dimensions: Length - 1000mm X Width - 600mm X Height - 1700mm Frame Material: Stainless Steel Tubing Stainless Tube Diameter: At Least 35mm Black Powder Coated Steel Platform With Carpeted Surface And Rubber Bumper At The Edge With 4 Pieces X 200mm Diameter Black Pneumatic Swivel Wheels Packed With Shipping Carton Box Branded 1 Pcs Cash Register With Drawer Printer: Width: 57mm (minimum) Speed: 2 Lines/sec (minimum) Lcd Display Size: 5cm Width X 10cm Long(minimum) With Drawer At Least 4 Bills And 5 Coins Compartments With Drawer Dimension At Least 410mm Width X 450mm Depth Input Method: Numeric 10-key Interface With At Least 2 Ports Power Source: 220-240volts Ac, 50/60hz; With Ac/dc Adapter Can Be Operated With Battery Programmable User's Manual In English Which Includes: A. Parts Manual With Labels, 1 Pcs Credit Card Imprinter Height Of The Imprinter 2 1/2 Inch (minimum) X Width 5 1/2 Inch (minimum) X Length 11 Inches (minimum) Carriage Material: Steel Body:plastic Color: Black 20 Characters Per Line Card Mounting Can Accepts At Least 0.030" Thick Size Credit Cards Plate Can Accommodate Up To 5 Lines, Manual Type With User's Manual In English Which Includes: A. Parts Manual With Labels, B. Assembly Instructions, C. Operating Procedures 30 Pc Credit Card Voucher Holder Material: 3 Mm Thick Clear, Acrylic, Dimensions: Height: At Least 255 Mm, Width: At Least 210 Mm, Thickness: At Least 70 Mm 1 Pcs Detector, Fake Bills Led Display; Led Display Size: At Least 5 Cm Width X 10 Cm Long; Hard Plastic Casing; Ultraviolet (uv) And Magnetic (mg) Sensors; Power Source: Built In Rechargeable Battery,12v Output And Ac 100- 240v Adapter; With Complete Detection; Accessories Includes: Tough Plastic Carrying Case, Power Cord, Cleaning Brush, And Power Charger; User's Manual In English Which Includes: A. Parts Manual With Labels, B. Assembly Instructions, 3 Pcs Guest Folio Rack Material: Hard Plastic; Accommodates At Least 50 Room Divider Indexes; With Divider Boards With Metal Tabs; A4 Size Divider; With Metal Sidings 1 Pc Hypercom Memory: 1 Mb Ram (minimum) Lcd Display; 160 X 80 Pixel Graphics (minimum) With Card Reader Magnetic Stripe Pin Pad Port: 4-wire, Rs485; With Peripheral Ports For Pc Connection; Electronic Cash Register Or Journal Printer; With At Least 2400bps Modem; Support Synchronous (sdlc) And Asynchronous, Lan Operation; With Pin Encryption; With Thermal Printer At Least 576 Dots Per Line; Thermal Paper – 2 Inches Wide X 3 Inches Roll Diameter (min.); Keypad: Membrane, 12 Keys, Water-resistant; 1 Pc Key Card Maker With Verifier Set Of Hotel Door Lock System With Management Software; A) 1 Unit - Card Type Door Lock With Inductive Distance At Least 4cm B) 1 Unit - Card Encoder Unit With 25 Pieces Door Room Key Cards Computer Software System For Door Lock And Making Cards With Complete Accessories Including The Usb Type A Cable Interface To The Computer User's Manual In English Which Includes: A. Parts Manual With Labels, B. Assembly Instructions C. Operating Procedures On How To Use The Equipment 1 Pcs Key Rack Rack Material: Wood Number Of Racks: Can Accommodate At Least 40 Key Cards Minimum Rack Size: 70mm Width X 110mm Height Depth Of The Rack At Least 50mm Any Color Paint Type:wall Mounted Rack Pack With Shipping Carton Box 1 Pc Safety Deposit Box Vault Material: Metal, Powder Coated, Solid Steel Door Thickness: 4mm(minimum) Body Thickness: 2mm(minimum) Minimum Outer Dimension: L: 30cm X H: 20cm X W: 20cm Electronic Lock System Battery Operated Digital Panel: Requires 4 X ‘aa’ Batteries User's Manual In English Which Includes: A. Parts Manual With Labels, B. Assembly Instructions, C. Operating Procedures On How To Use The Equipment, Branded 20 Pcs Speaker, Lapel Frequency At Least 500mhz With Audio Input Connector With Operation Range At Least 50meters Receiver/70ma Earphone Output Level: 32ohm, 65mw Operates With Energizer Battery With Minimum Powerconsumption Of Transmitter At Least 3v/70ma Receiver: 3v/70ma 25 Sets First Aid Kit Type: Emergency Case; Contents: First Aid Quick Reference Guide, 1pc; Sterize Gauge Swab(4 X4 X12 Ply) 100 Pcs/pack, 1 Pack; Adhesive Strips/band -aid, 50 Pcs/pack, 2 Packs; Gloves, Disposable, Medium Size, 2 Pairs; Hypo Allergenic Adhesive Tape, 5cm X 5cm, 2 Rolls; Triangular Bandage/arm Sling, Min 90cm X 90cmx 120cm, 2pcs; Safety Pins, 1 1/4 Inches, (12 Pcs), 1 3/4 Inches (12 Pcs); Stainless Steel Bandage Scissors, 2pcs; Betadine, 60ml, 2 -3 Years Expiration, 2 Bottles; Dust Mask, 2pcs; Hand Towels Or Face Towels, White Color, 6 Pcs; Gauze Bandage, Minimum 5cm X 4cm, 2 Rolls; Antiseptic Handwash/germicidal Soap, 60 Gms , 2pcs; Torniquet, 2 Pcs; Spirit Of Ammonia, 30ml, 2-3 Years Expiration, 1 Bottle; Burn Cream Ointment, 20g To 30g, 2- 3years Expiration, 1 Tube; Medical Tweezers Min. 8cm, Plastic, 2pcs; Plastic Bags, Resealable, Minimum Of 24pcs, 100mm X 180mm, 24pcs, 150mm X 230mm Cotton Balls , 50 Balls In A Sealed Package, 2 Packs Hot And Cold Pack, Reuseable, 1 Pack Water Resistant And Sturdy Case W/ Handle That Can Accommodate All The Listed Items. 4 Pcs Megaphone Battery Operated (4 Pcs - Size D Battery) With Built-in Siren Power Output: 20-watts (minimum) Range: 700 Meters (minimum) With Hand Grip And Carrying Strap Branded With Users Manual That Contains The Specification, List Of Parts, Instruction Guide, Troubleshooting, Safety Instruction. 100 Pcs Whistle Anodized Aluminum;size : Length - 6.5cm X 3cm Diameter; Handy And Lightweight; Loud Whistle Can Be Heard For Far Distance Of 100 Meters; With Key Ring For Attachment 2 Pcs White Board, Floor Standing, Rolling Board: White Formica Laminated, Plane Will Not Deform.board Size: Rectangular 1800mm W X 1000 To 1200mm H, Board Edges Secured With Aluminum Clip Edging 17 Mm (minimum) Wih Plastic Corner Capscomes With Metal Tray For Marker And Eraserthe Stand And Frame Are Constructed With Aluminum Or Powder Coated Steel 25mm Square Tube (minimum), Sturdy, No Wobblewith 4 Lockable Hard Plastic Caster Wheelsoverall Height From Floor: 210 To 214cmsmooth Surface, No Sharp Edges Total Abc 3,978,106.00 2. The Department Of Education – Division Of Tangub City Now Invites Bids For The Above Procurement Project. Second Procurement Of Learning Tools And Equipment For Technical Vocational Livelihood To Deped-public Schools. Bidders Should Have Completed A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii (instructions To Bidders). 3. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) No. 9184. 4. Interested Bidders May Obtain Further Information From Department Of Education – Division Of Tangub City And Inspect The Bidding Documents At The Address Given Below From 8:00 A.m. To 5:00 P.m. , Mondays To Fridays Except Holidays. 5. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders On January 8, 2025 From Given Address And Website/s Below And Upon Payment Of The Applicable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb, In The Amount Of: Lot 1 - Five Hundred Pesos (p500.00) Lot 2 - Five Hundred Pesos (p500.00) Lot 3 - Five Hundred Pesos (p500.00) Lot 4 – One Thousand Pesos (p1,000.00) Lot 5 - Five Thousand Pesos (p5,000.00) Lot 6 - Five Hundred Pesos (p500.00) Lot 7 – One Thousand Pesos (p1,000.00) Lot 8 - Five Hundred Pesos (p500.00) The Procuring Entity Shall Allow The Bidder To Present Its Proof Of Payment For The Fees To Be Presented In Person. 6. The Department Of Education – Division Of Tangub City Will Hold A Pre-bid Conference On January 20, 2025, 9:00 Am At Division Office Conference Hall Which Shall Be Open To Prospective Bidders. 7. Bids Must Be Duly Received By The Bac Secretariat Through Manual Submission At The Office Address As Indicated Below On Or Before 9:00 A.m. On February 4, 2025. Late Bids Shall Not Be Accepted. 8. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 16. 9. Bid Opening Shall February 4, 2025, 9:00 A.m. At The Given Address Below. Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend The Activity. 10. Bidders Or Its Authorized Representatives Are Encouraged To Attend The Pre-bid Conference To Ensure That They Fully Understand The Procuring Entity’s Requirements. 11. The Department Of Education – Division Of Tangub City Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Implementing Rules And Regulations (irr) Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 12. For Further Information, Please Refer To: Gina L. Mandawe Head, Bac Secretariat Deped, Division Of Tangub City, Anecito Siete St., Mantic, Tangub City 7214 (088) 530-5988 Depedtangub.bacsec@deped.gov.ph Https://tangub.deped.gov.ph/ 13. You May Visit The Following Websites: For Downloading Of Bidding Documents: Https://tangub.deped.gov.ph/ Erlinda G. Dael, Phd., Cese Assistant Schools Division Superintendent Bac Chair

Details: Description 1 1 Copy Advanced Marketing Management/abante, Etc/2024 2 1 Copy Advanced Local Government And Regional Administration Development/abante, Etc/2024 3 1 Copy Advanced Production And Operation Management/abante, Etc/2024 4 1 Copy Advanced Public Fiscal Management, Finance And /abante, Etc/2024 5 1 Copy Assessment Of Learning 1/manas/2024 6 1 Copy Banking And Financial Institutions/bairan/2024 7 1 Copy Capital Markets/bairan/2024 8 1 Copy Charater Formation 1-patrotism And Nationalism/adra, Etc/2024 9 1 Copy Character Formation 2-leadership Making , Management And Administration/adra, Etc/2024 10 1 Copy Character Formation 1- Patriotism And Nationalism 3rd Ed./rondina, Etc/2024 11 1 Copy Character Formation 2-leadership Making , Management And Administration 3rd Ed./literfal, Etc/2024 12 1 Copy Comparative Model In Policing 4th Ed./castillo, Jr./2024 13 1 Copy Comparative Models Of Policing And Philippine National Police Policing ( Based On Prc Tos)/depayso/2024 14 1 Copy Criminological Research 2nd Ed./chavez, Etc/2024 15 1 Copy Criminological Research A Self Study Guide/depayso/2024 16 1 Copy Dispute Resolutions And Crises/incident Management/cano, Etc/2024 17 1 Copy Essentials Of Risk Management/banaag/2024 18 1 Copy Evidence/gabao/2024 19 1 Copy Facilitating Student-centered Teaching & Learning/larioque. Etc/2024 20 1 Copy Financial Analysis And Reporting/bairan/2024 21 1 Copy Financial Markets/bairan/2024 22 1 Copy Forensic Examination On Questioned Documents 5th Ed./alvarez/2024 23 1 Copy Forensic Photography 6th Ed./bulan/magadia/2024 24 1 Copy Fundamentals Of Criminal Investigation And Intelligence/tad-awan/2024 25 1 Copy Handbook In Juvenile Deliquency And Violence Againts Women And Their Children/barican/dausan/abordo/2024 26 1 Copy Human Behavior And Victimology /depayso/2024 27 1 Copy Human Development-understanding Criminal Behavior And Victimology/togana/2024 28 1 Copy Inclusive Education In Early Childhood Settings/boholona, Et Al./2024 29 1 Copy Income & Business Taxation/bairan/2024 30 1 Copy Introduction To Consumer Behavior/pasahol/2024 31 1 Copy Introduction To Criminology /caballero/barican/2024 32 1 Copy Introduction To Criminology/cabrillas, Et Al/2024 33 1 Copy Introduction To Cybercrime & Basic Digital Investigative Analysis 3rd Ed/lagumen/lagumen/2024 34 1 Copy Introduction To Cybercrime Investigation And Environmental Laws And Protection/detran,et Al/2024 35 1 Copy Introduction To Industrial Security Concepts /depayso/2024 36 1 Copy Introduction To Industrial Security Concepts 4th Ed/bobier/2024 37 1 Copy Juvenile Delinquency And Juvenile Justice System 2nd Ed./detran/literal/2024 38 1 Copy Law Enforcement Operationss And Planning With Crime Mapping/tancangco/2024 39 1 Copy Non- Institutional Corrections 3rd Ed/chavez Et Al./2024 40 1 Copy Practical Methods On Roads-bridge & Drainage Structures Construction/porte/2024 41 1 Copy Retail And Wholesale Enterprises/bairan/2024 42 1 Copy Special Crime Investigation With Interview And Interrogation Protocols/domingo/2024 43 1 Copy Special Education Book 1/reyes, Pascual/2024 44 1 Copy Strategic Operations Management 2nd Ed./serrano/2024 45 1 Copy Survey Of Afro-asian Literature/escalada-cordova,uytico/2024 46 1 Copy Principles Of Total Quality Management/pasahol, Etc/2024 47 1 Copy The Contemporary World/mananay,etc/2024 48 1 Copy The Teacher And The School Curriculum/gallardo/ Mañas/ 2024 49 1 Copy Theories Of Crime Causation/salamanca, Et Al/2024 50 1 Copy Teaching And Assessment Of Grammar/manas/2024 51 1 Copy Therapeutic Modalities 3rd Ed./balares Et Al./2024 52 1 Copy The Teaching Profession In The 21st Century/sarandi, Babao/2024 53 1 Copy The Teaching Profession/fernando,et Al/2024 54 1 Copy Traffic Management & Accident Investigation With Driving 2nd Ed./apela, Et Al./2024 55 1 Copy Understanding Marketing Research/mutya/2024 56 1 Copy Vice And Drug Education And Control 4th Ed/cejes/libres/ 2024 57 1 Copy Vice And Drug Education And Control /tad-awan,et Al./2024 58 1 Copy Advance Management Information System/abante,et Al./2023 59 1 Copy Computer Fundamentals/revano/2023 60 1 Copy Data Analytics & Business Intelligence/abante,et Al/2023 61 1 Copy Dispute Resolution And Incident Management/capdos/lud-ayen/2023 62 1 Copy Information Management/cortez/2023 63 1 Copy Franchising/stevens/2024 64 1 Copy Advanced Management Information Management System (mis)/abante,et.al/2023 65 1 Copy Introduction To Application Development And Emerging Technologies/pomperada/2023 66 1 Copy Principles Of Foundation Engineering Based On The National Structural Code Of The Phils. 2015/castro/2023 67 1 Copy Simplified Steel Design Asd & Lrfd Based On Nscp 2015 & Aisc's Steel Construction And Manual 14e/2023/castro 68 2 Copy Teaching Science In The Elementary Grades Vol. 2: Physics, Earth And Space Obe- & Ppst Based/bilbao, Etc/2024 69 2 Copy The Teacher And The School Curriculum Obe Approach/otiner-gallardo/2024 70 2 Copy Theoretical And Practical Textbook On Lesson Planning/ Sanchez/2024 71 2 Copy Ang Bisa Ng Pag Uulit Sa Katutubong Panitikan/yapan, Alvin B./2023 98 2 Copy Introduksiyon Sa Pananaliksik Sa Wika At Panitikan (luzon)/alvarado Et Al/2022 99 2 Copy Introduksiyon Sa Pananaliksik Sa Wika At Panitikan (vizmin)/arbasto Et Al/2022 100 2 Copy Sangguniang Aklat Ng Gramatika At Pagbuo Ng Mapa/alvarado Et Al/2023 101 2 Copy Sinesosyedad: Panunuri Ng Piling Pelikulang Panlipunan/de Leon/2023 102 2 Copy Commissary Food Service/donray/2024 103 2 Copy Readings In Philippine History/dela Vega/2024 104 2 Copy Rizal And The Development Of Filipino Nationalism /garcia, Etc/2023 105 2 Copy Transcendence: Understanding Contemporary Global Dynamics, Issues, And Challenges/calilung And Coronacion/2024 106 1 Copy Environmental And Natural Resources Laws With Commentaries, Annotations… ( Hb)/claridades/2024 107 2 Copy Introduction To Philippine Politics & Governance ( With Basic Constitutional Provisions)/baes & Beler/2024 108 2 Copy Introduction To Philippine Government And Politics With Basic Constitutional Principles 2e/riodique/2024 109 2 Copy Mathematics In Modern World/reynoso, C./2024 110 1 Copy Indigenous Creative Arts/camboles, M./2024 111 1 Copy Understading The Self/vazquez, I./2024 112 1 Copy Understanding The Self: New Normal Edition/palean,et.al/2024 113 2 Copy Biological Chemistry Obe-based/chua,et.al/2022 114 2 Copy Earth Science: Quaternary Earth, The Age Of Humans, 2e/reyes/2023 115 1 Copy Physical Science/santos/2023 116 2 Copy Gender And Society/bacolod, Et Al. /2024 117 2 Copy The Revised Penal Code Book I - Understanding Criminal Law 2nd Edition/tulalian/2024 118 2 Copy Fundamentals Of Criminal Law - Revised Penal Code Book 1/abastillas /manlusoc/2023 119 2 Copy The Revised Penal Code Book Ii, Specific Crimes And Their Elements 2nd Edition/tulalian/2024 120 2 Copy Criminal Procedure A Handbook For Criminology Students 3rd Edition/gabao/ Tulalian/2024 121 2 Copy Basic Criminal Procedure/tulalian/2022 122 2 Copy Introduction To Criminology/magtaan/ Cabrillas/2024 123 2 Copy Introduction To Criminology - A Guidebook For Criminology Instructors And Students/caballero/ Barican/2024 124 2 Copy Introduction To Criminology/rectin/2023 125 2 Copy Theories Of Crime Causation - An Instruction And Learning Guide/caballero/ Barican/2024 126 2 Copy Human Behavior And Victimology/depayso/2024 127 2 Copy Human Development - Understanding Criminal Behavior And Victimology/togana/2024 128 2 Copy Handbook In Human Behavior And Victimology/dausan Et Al/2023 129 2 Copy Professional Conduct & Ethical Standards/lud-ayen/2023 130 2 Copy Police Professional Conduct And Ethical Standards With Police Community Relations/dascil /santos/2022 131 2 Copy Handbook In Juvenile Delinquency And Violence Against Women And Their Children/barican /dausan/ Abordo/2024 132 2 Copy Dispute Resolutions And Crises / Incident Management/caño/2024 133 2 Copy Dispute Resolution And Incident Management/capdos/ Lud-ayen/2023 134 2 Copy The Research Recipe - A Guide To Writing Research Proposals In Criminal Justice (first Serving)/donato/2024 135 2 Copy Criminological Research - A Self Study Guide/depayso/2024 136 2 Copy Criminological Research 2 - A Textbook For Criminology Students/caño/2023 137 2 Copy Comparative Models Of Policing And Philippine National Police Policing (based On Prc Tos 2022)/depayso/2024 138 2 Copy Comparative Models In Policing/moyao/2023 139 2 Copy Introduction To Industrial Security Concepts/depayso/2024 140 2 Copy Law Enforcement Operations And Planning With Crime Mapping/tancangco/2024 141 2 Copy Law Enforcement Operations And Planning With Crime Mapping/taynan /lopez/2023 142 2 Copy Law Enforcement (police) Operations And Planning With Crime Mapping/florendo/2023 143 2 Copy Fingerprint - Uniqueness And Persistency Of Friction Ridge Skin Volume 1/rocamora/2023 144 2 Copy Forensic Science 2 - Personal Identification Laboratory Manual/badua/2023 145 2 Copy Forensic Photography/tad-awan/2023 146 2 Copy Deceptive Minds - Unmasking The Art Of Lie Detection/moyao/2024 147 2 Copy Introduction To The Forensic Sciences/taduran/2024 148 2 Copy Fundamentals Of Criminal Investigation And Intelligence/ Lopez/ Taynan Jr./2024 149 2 Copy Fundamentals Of Criminal Investigation And Intelligence/tad-awan/2024 150 2 Copy Essentials In Criminal Investigation/tamayo/2023 151 2 Copy Fundamentals Of Criminal Investigation With Intelligence 2nd Edition/florendo/2023 152 1 Copy Specialized Crime Investigation With Legal Medicine/dascil /santos/2023 153 1 Copy Special Crime Investigation With Interview And Interrogation Protocols/domingo/2024 154 1 Copy Vice And Drug Education And Control/tad-awan/ Lud-ayen/2024 155 2 Copy Introduction To Cybercrime And Environmental Laws/tad-awan/2024 156 2 Copy Introduction To Cybercrime And Environmental Laws/caño/2023 157 2 Copy Institutional Correction For Criminology Students/villaluz/2024 158 2 Copy Institutional Correction (new Curriculum And Cle Tos Compliant)/tumitit/ Estoque/2023 159 1 Copy Non-institutional Correction (community-based Correction In The Philippines) For Criminology Students/villaluz/2023 160 1 Copy Non-institutional Corrections/danglosi/2023 161 1 Copy Therapeutic Community Modality 1/foronda/2023 162 1 Copy Moral Philosophy And Ethics/bacuyag/2024 163 1 Copy Guiness World Records 2024 164 1 Copy Introduction To Ethics/umali,et Al/2023 165 1 Copy Leisure And Recreation Management For Tourism And Hospitality Industry/cornell/2023 166 1 Copy Living In The Information Technology Era/abante/2023 167 1 Copy Management Science ( Quantitative Methods For Business Operations Research)/sirug/2023 168 1 Copy Methods Of Research In Business Education 2nd Edition/flores/2023 169 1 Copy Professional Conduct And Ethical Standards 2nd Ed./nabe/2023 170 1 Copy Professional Salesmanship/camillar-serrano/2023 Ppc Library 171 1 Copy Criminal Justice System The Philippine Context/atty. Tutalian, V./ 2022 172 1 Copy Introduction To Criminology - A Guidebook For Criminology Instructors And Students/caballero/ Barican/ 2024 173 1 Copy Introduction To Criminology And Psychology Of Crimes/leyaley/2021 174 1 Copy Comprehensive Correctional Administration Handbook With Therapeutic Modalities/apela/2019 175 1 Copy Crime Theories, Causes & Prevention/domingo, C./2023 176 1 Copy Law Enforcement Administration 3rd Edition/manwong / 2021 177 1 Copy Law Enforcement Organization And Administration Inter-agency Approach / Taynan /lopez / 2021 178 1 Copy Comparative Models In Policing/moyao/2021 179 1 Copy Comparative Models Of Policing And Philippine National Police Policing (based On Prc Tos 2022)/2024/depayso 180 1 Copy Comparative Models In Policing 3rd Ed./ Castillo / 2023 181 1 Copy Institutional Correction For Criminology Students/ Villaluz/2024 182 1 Copy Introduction To Industrial Security Concepts/ Depayso / 2024 183 1 Copy Introduction To Industrial Security Concepts 3rd Ed. D. Bobier/2023 184 2 Copy Special Crime Investigation 1 With Legal Medicine Instructional Modules/ Rogo, A./2022 185 2 Copy Special Crime Investigation With Interview And Interrogation Protocols/ Domnigo/ 2024 186 2 Copy Special Crime Investigation With Legal Medicine 2nd Ed./2023/pltcol Sabino-diangson 187 2 Copy Character Formation 2 - Leadership, Decision Making, Management And Administration 2nd Ed/b. Literal .et.al/2023 188 2 Copy Character Formation 1 Nationalism And Patriotism 2nd Edition/caballero/ Barican/2023 189 2 Copy Forensic Photography For Criminology Students And Practitioners With Laboratory Manual 3rd Edition/2022/villarba 190 2 Copy Forensic Photography 5th Ed./m.e. Bulan/m.e. Magadia/2023 191 2 Copy Fingerprint Uniqueness Abd Persistency Of Friction Ridge Skin Vol. 1/rocamora/ 2023 192 2 Copy Fingerprint Identification (do Fingerprints Lie?)/ Leyaley/2021 193 2 Copy Human Rights Education 2nd Ed. /l.c. Rondina/m. Seguido/2023 194 2 Copy Human Rights Education A Textbook Fro Criminal Justice Education Students And Law Enforcers/tantangco And Orlain, Jr./2022 195 2 Copy Police Professional Conduct And Ethical Standards With Police Community Relations/dascil & Santos/2022 196 2 Copy Technical English 1 & 2 (legal Forms) For Criminology Students/balares/2023 197 2 Copy Technical English ( Investigative Report Writing) For Criminology Students/zaspa & Manlangit/2022 198 2 Copy Therapeutic Community Modality 1/2023/foronda 199 1 Copy Compendium Of Laws On Taxation Revised Ed, Year 2023/dascil, R./2023 200 1 Copy Basic Approach To Income Taxation/ Dimaapao/2021 201 2 Copy Income & Business Taxation/ Basiran/2024 202 1 Copy Income Taxation Laws Principles And Applications 2023-2024 Edition. Banggawan/2023 203 1 Copy Introduction To Special Civil Action/tulalian, V.t./2021 204 2 Copy Introduction To Public Administration 2e/bihasa, Cr./2022 205 2 Copy Pricing Strategy Obe Approach/agustin-acierto, M/2022 206 2 Copy Administrative And Office Management 1e/ Magno, R./2024 207 2 Copy Basic Financial Management In The Philippine Setting Obe Approach/martin, M/2022 208 2 Copy Business Laws And Regulations /dela Cruz-cada/2021 209 2 Copy The Law On Obligations And Contracts/de Leon, H./2021 210 2 Copy Essentials Of Administrative Office Management/sergote/2022 211 2 Copy Executive Leadership Advisory & Development: A Comprehensive Guide For Graduate Program Students/2024 212 1 Copy Ethics In Public Service ( Hb)/ Aquino/2023 213 1 Copy Public Fiscal Policy And Administration (hb)/gupta, S./2023 214 1 Copy Destination Management & Marketing/arenas/2022 215 1 Copy Macro Perspective Of Tourism And Hospitality/yeung/2023 216 1 Copy Marketing For Tourism And Hospitality Obe Approach/camilar-serrano, A./2020 217 1 Copy Micro Perspective Of Tourism And Hospitality/bajao Et.al/2022 218 1 Copy Kitchen Essentials & Basic Food Preparation/remaneses, Et.al/2023 219 1 Copy Kitchen Essenttials And Basic Food Preparation 2e/velasquez/2024 220 1 Copy Cost Control In Hospitality Industry/fababaer,et.al/2020 221 1 Copy Strategic Management In Tourism And Hospitality Industry W/ Total Quality Mgt./vizconde Et. Al/2021 222 1 Copy Supply Chain Management In Hospitality Industry 2e/de Castro, K/2024 223 1 Copy Ergonomics And Facilities Planning For The Hospitality Industry 2e/ Mendoza/2024 224 1 Copy International Business & Trade /lopez-mariano, N/2023 225 1 Copy International Business & Trade Obe Approach/martin, M./2021 226 1 Copy Synergizing E-commerce, Social Media, And Dropshipping: Navigating The Path To Success & Customer Satisfaction Obe Approach/garcia,et.al/2023 227 1 Copy Total Quality Management Obe Approach 2e/camilar-serrano, A./2023 228 1 Copy Banking And Financial Institutions/ Bairan/2024 229 1 Copy Personal Finance 2022 Edition/cabrera/2022 230 1 Copy Financial Management 1e/yu/2024 231 1 Copy Foundations Of Special And Inclusive Education/aligada-halal,et.al/2020 232 1 Copy Transformissional Values Education/2020 233 1 Copy Rural Development (administration And Planning)/ 9789350147801/ Gautam/2024 234 1 Copy Encyclopedia Of Science And Technology/chandra/ 2023/ 9781774693872 235 1 Copy Public Administration: Partnerships In Public Service/edwards/2024/9781639878246 236 1 Copy Microeconomics/mcconnell/23rd/9781266107887 237 1 Copy Education, Social Reform And Philosophical Development: Evidence From The Past, Principles For The Future/pring/2022 238 1 Copy Government Budgeting/kumar/2022/9789394137134 239 1 Copy Entrepreneurship And Innovation/kaur/9789392407918 240 1 Copy Attitude Of Moral Values/balakrishnan/2022 241 1 Copy Fieldwork Training In Social Work/parkash/2022 Busuanga Library 242 2 Copy Risk Management W/ Haccp As Applied To Safety, Security And Sanitation 2nd Edition/mylene Yeung/2025 243 2 Copy Macro Perspective Of Tourism And Hospitality 2nd Edition/mylene Yeung/2025 244 2 Copy Micro Perspective Of Tourism And Hospitality 2nd Edition/mylene Yeung/2025 245 2 Copy Philippine Culture And Tourism Geography 3rd Edition/mylene Yeung/2025 246 2 Copy Quality Service Management In Tourism And Hospitality 3rd Edition/chester Arenas/2024 247 2 Copy Tourism And Hospitality Marketing 2nd Edition/chester Arenas/2025 248 2 Copy Professional Development And Applied Ethics /chester Arenas/2022 249 2 Copy Legal Aspect In Tourism And Hospitality 2nd Edition/melinda Bascos/2024 250 2 Copy Entrepreneurship In Tourism And Hospitality /chester Arenas/2022 251 2 Copy Multicultural Diversity In Workplace 2nd Edition/mylene Yeung/2025 252 2 Copy Introduction To Meetings, Incentives Conferences And Events Management/chester Arenas/2025 253 2 Copy Applied Business Tools And Technologies 3rd Ed/james Saycip/2025 254 2 Copy Supply Chain Management In Hospitality Industry 2nd Ed/ Kyla De Castro/2024 255 2 Copy Medical And Wellness Tourism/porbile/2024 256 2 Copy Fundamentals Of Culinary Arts/santillan/2024 257 2 Copy Bread And Pastry/portman/2025 258 2 Copy Cookery Ncii/villasis/2025 259 2 Copy Human Resource Management In Hospitality And Tourism Industry/escobar/2024 260 2 Copy Trends And Issues In The Hospitality Industry/2026 261 2 Copy Ergonomics And Facilities Planning For The Hospitality Industry 2nd Ed/lolita Mendoza/2024 262 2 Copy Global Culture And Tourism Geography 3rd Edition/marie Angeles/2025 263 2 Copy Tour And Travel Management 3rd Edition/sarah-po/2025 264 2 Copy Transportation Management 2nd Edition/james Saycip/2025 265 2 Copy Fundamentals In Food Service Operations/bryan D. Baliste/2023 266 2 Copy Fundamentals In Lodging Operations 3rd Edition/arenas/baliste/2025 267 2 Copy Sustainable Tourism 3rd Edition/marie Angeles/2025 268 2 Copy Tourism Policy Planning And Development/ Dino Et. Al/2022 269 2 Copy Research In Tourism And Hospitality 2nd Edition/lolita Mendoza/2025 270 2 Copy Foreign Language (french And Japanese)/karol Aquino/2025 271 2 Copy Strategic Management W/ Tqm In Tourism And Hospitality Industry/vizconde Et. Al/2023 272 2 Copy Operations Management For Tourism And Hospitality Industry 2nd Ed/vizconde Et. Al/2025 273 2 Copy Heritage Tourism/vizconde Et. Al/2023 274 2 Copy Tour Guiding/vizconde Et. Al/2022 275 2 Copy Cruise Tourism/vizconde Et. Al/2021 276 2 Copy Food And Beverage Labor Cost Control 2nd Edition/lyndsey Velasquez/2024 277 2 Copy Bread And Pastry/karol Aquino/2022 278 2 Copy Meat And Poultry Fabrication 2nd Ed/lolita Mendoza/2024 279 2 Copy Food Processing 2nd Edition/jamille Jaravata/2024 280 2 Copy Tourism Information Management/lyndsey Velasquez/2021 281 2 Copy Culinary Nutrition/ Lolita Mendoza/2023 282 2 Copy Asian Cuisine/jam Melchor/2022 283 2 Copy Philippine Regional Cuisine/jam Melchor/2024 284 2 Copy Gastronomic Tourism/vizconde Et. Al/2021 285 2 Copy Food And Beverage Services/vizconde Et. Al/2025 286 2 Copy Housekeeping Operations 2nd Edition/vizconde Et. Al/2024 287 2 Copy Bar And Beverage Management/vizconde Et. Al/2024 288 2 Copy Room Division Cost Control/arenas/2022 289 2 Copy Menu Design And Revenue Management 2nd Edition/chester Arenas/2024 290 2 Copy Destination Management And Marketing 2nd Edition/chester Arenas/2025 291 2 Copy Quantity Food Production: A Guide For Commercial Cooking Nc Iii/entrata Et. Al/2022 292 2 Copy Banquet And Catering Management/vizconde Et. Al/2025 293 2 Copy Front Desk Operations/vizconde Et. Al/2022 294 2 Copy Tourism Product Development/vizconde/2025 295 2 Copy Recreation And Leisure Management/etrata Et. Al/2022 296 2 Copy International Cuisine/victoriano Et.al/2022 297 2 Copy Food Styling And Design/etrata Et. Al/2025 298 2 Copy Cookery/etrata Et. Al/2022 299 2 Copy Travel Writing And Photography/vizconde Et. Al/2024 300 2 Copy Crowd And Crisis Management/vizconde Et. Al/2022 301 2 Copy Environmental Conservation In Tourism/vizconde Et. Al/2022 302 2 Copy Trends And Issues In Hospitality Industry/etrata Et. Al /2022 303 2 Copy Quick Food Service Operations/etrata/2022 304 2 Copy Culinary Mathematics/santiago/2023 305 2 Copy Data Analytics In Hospitality/jaravata/2024 306 2 Copy Fundamentals Of Food Science And Technology/valle/2024 307 2 Copy Butchery And Fish Mongerie/valle/2024 308 2 Copy Garde Manger/bonfor/2024 309 2 Copy Classical French Cuisine/caridad/2024 310 2 Copy Specialty Cuisine/rabor/2024 311 2 Copy Halal Cookery/marinez/2024 312 2 Copy Gastronomy (food And Culture)/alba/2024 313 2 Copy Oenology (making Of Wine And Spirits)/antomio/2024 314 2 Copy Revenue Management/isla/2024 315 2 Copy Franchising /stevens/2024 316 2 Copy Commissary Food Service/donray/2024 317 2 Copy Accommodation Operations And Management/medalye/2024 318 2 Copy Hospitality And Tourism Facilities Management And Design/gutang/2024 319 2 Copy Agritourism/medalye/2024 320 2 Copy Tourism Property Management And Development/victoria/2024 321 2 Copy Tourism Estate And Integrated Resort Industry/manzano/2024 322 1 Copy Events Management, 2nd Ed./dela Cruz/2024 323 1 Copy Essentials Of Risk Management/banaag/2024 324 1 Copy Facilities Planning & Management, 2nd Ed./serrano/2024 325 1 Copy Front Office System And Procedures, Rev. Ed./lago,lim/2024 326 1 Copy Introduction To Research/sergote/2024 327 1 Copy Learning Research The Easy Way Rev.ed/uriarte/2024 328 1 Copy Mastering Modern Supply Chain For Tourism And Hospitality Industry/maranan,et Al./2024 329 1 Copy Principles Of Total Quality Management/pasahol Et Al./2024 330 1 Copy Productivity And Quality Management 2nd Ed./serrano/2024 331 1 Copy Spanish For Beginners, 2nd Ed./perez,ramonito/2024 332 1 Copy Strategic Management/austria, Etc/2024 333 1 Copy Strategic Management In Tourism And Hospitality Industry/buenaventura,gutierrez/2024 334 1 Copy Strategic Operations Management 2nd Ed./serrano/2024 335 1 Copy Sustanable Tourism: A Comprehensive Guide To Promoting Responsible Travel/maranan, Etc/2024 336 1 Copy The Evolving Landscape Of Strategic Management And Leadership/perida, Arcadio/2024 337 1 Copy Bar And Beverage Management-a Book Of Drinks 2nd Ed./bajao/osorno/2023 338 1 Copy Boarding House/jaileen F. Jimeno/2023 339 1 Copy Ergonomics And Facilities Planning For The Hospitality Industry /buenaventura/2023 340 1 Copy Fundamentals In Lodging Operations/sarah Monson-po/2023 341 1 Copy Fundamentals Of Lodging Operations With Housekeeping Laboratory Manual/bajao/osorno/2023 342 1 Copy Kitchen Essentials And Basic Food Preparation/remaneses, Et Al./2023 343 1 Copy Operations Management In Tourism And Hospitality/buenaventura, Et Al./2023 344 1 Copy Practicum Manual For Tourism And Hospitality Management/taoing,cabugon/2023 345 1 Copy Professional Development And Applied Ethics/cabulay/2023 346 1 Copy Quality Service Management In Tourism And Hospitality/buslon/osorno/2023 347 1 Copy Professional Conduct & Ethical Standards/lud-ayen/moyao/2023 348 1 Copy Quantity Cookery And Catering Management ( A Guide To Students,leading To Commercial Cooking Nc Iii)/prades/2023 349 1 Copy Risk Management As Applied To Safety Security And Sanitation 2nd Ed/somoray/2023 350 1 Copy Sustainable Tourism/bajao/osorno/2023 351 1 Copy Sustainable Tourism/santos/2023 352 1 Copy Applied Business Tools And Technologies In Hotel And Restaurant Management (hrm)/gonzalo, Etc/2023 353 1 Copy Foreign Language I (basic French For Hospitality Management And Tourism I)/ Tomas/2022 354 1 Copy Foreign Language Ii (basic French For Hospitality Management And Tourism I)/tomas/2022 355 1 Copy Tourism Policy Planning And Development/cruz/2022 356 1 Copy Fundamentals In Food Service Operations/yao/2022 357 1 Copy Supply Chain Management In Hospitality Industry/baluyot/2022 358 1 Copy Assessment Of Learning 1/manas/2024 359 1 Copy Charater Formation 1-patrotism And Nationalism/adra/2024 360 1 Copy Character Formation 2-leadership Making , Management And Administration /adra/2024 361 1 Copy Character Formation 1- Patriotism And Nationalism 3rd Ed./rondina/2024 362 1 Copy Character Formation 2-leadership Making , Management And Administration 3rd Ed./literal/2024 363 1 Copy Entrepreneurial Behavior Growth Mindset And Fixed Mindset/pasahol/2024 364 1 Copy Entrepreneurial Management/ybanez/2024 365 1 Copy Facilitating Student-centered Teaching & Learning/larioque,et Al./2024 366 1 Copy First Aid, Rescue And Water Safety: A Self-regulated Learning Module /dogui-is/2024 367 1 Copy Gender And Society/bacolod, Et, Al./2024 368 1 Copy Inclusive Education In Early Childhood Settings/boholona, Et Al./2024 369 1 Copy Introduction To Criminology /caballero/barican/2024 370 1 Copy Introduction To Criminology/cabrillas, Et Al/2024 371 1 Copy Introduction To Research/sergote/2024 372 1 Copy Learning Research The Easy Way Rev.ed/uriarte/2024 373 1 Copy Moral Philosophy And Ethics/bacuyag/2024 374 1 Copy (path-fit 2) Physical Activity Towards Health And Fitness Rhytmic Dance And Social Activities/punzalan,habana/2024 375 1 Copy Promoting Community Change Through Civic Welfare Training Service 2/corpuz/2021 376 1 Copy Special Education Book 1/reyes,pascual/2024 377 1 Copy The Contemporary World/mananay/2024 378 1 Copy The Teacher And The School Curriculum/gallardo/mañas/2024 379 1 Copy Theories Of Crime Causation/salamanca, Et Al/2024 380 1 Copy Therapeutic Modalities 3rd Ed./balares Et Al./2024 381 1 Copy The Teaching Profession In The 21st Century/sarandi, Babao/2024 382 1 Copy The Teaching Profession/fernando,et Al/2024 383 1 Copy Understanding Society And Culture/riodique Iii/2024 384 1 Copy Upscaling Oral Communicationskills In The 21st Century Global Space/gutierrez, Et Al/2024 385 1 Copy Microeconomics Theories And Applications/marcelo/2023 386 1 Copy "technology For Teaching And Learning 1/ronato S. Ballado Marlo D. Alvarez, Alejandro L. Giray Jr./ 2023" 387 1 Copy Code Of Ethics Of Professional Teachers/estrada/2023 388 1 Copy A Course Module For Science In Early Childhood Education/joel Bernal Faustino , Eden Joy Pastor Alata, Antonnette Pawilen/2024 389 1 Copy A Course Module For Science In Early Childhood Education 1e/faustino/2024 390 2 Copy Fundamentals Of Criminal Investigation And Intelligence/tad-awan/2024 391 1 Copy Handbook In Juvenile Deliquency And Violence Againts Women And Their Children/barican/2024 392 1 Copy Human Behavior And Victimology /depayso/2024 393 2 Copy Human Development-understanding Criminal Behavior And Victimology/togana/2024 394 1 Copy Intelligent Leadership Resilience/perida/2024 395 1 Copy Introduction To Cybercrime & Basic Digital Investigative Analysis 3rd Ed/detrane/2024 396 1 Copy Introduction To Industrial Security Concepts /depayso//2024 397 1 Copy Introduction To Industrial Security Concepts 4th Ed/bobier/2024 398 1 Copy Introduction To Philippine Government & Politics With Basic Constitutional Provisions/baes/2024 399 1 Copy Juvenile Delinquency And Juvenile Justice System 2nd Ed./detran/2024 400 1 Copy Law Enforcement Operationss And Planning With Crime Mapping/tancangco/2024 401 1 Copy Learn And Enjoy Intermediate Statisitcs The Easy Way-advanced Volume 2 Rev. Ed/uriarte/2024 402 1 Copy Learn And Enjoy Statisitcs The Easy Way-basic Volume 1 Rev. Ed/uriarte/2024 403 1 Copy Microeconomics Numerical And Computational Approach/paurom/2024 404 1 Copy Non- Institutional Corrections 3rd Ed/chavez/2024 El Nido Library 405 1 Copy Introduction To Criminology/caballero/barican/2024 406 1 Copy Introduction To Criminology / Cabrillas, Et. Al/2024 407 1 Copy Facilities Planning & Management, 2nd Ed./serrano/2024 408 1 Copy Events Management, 2nd Ed./dela Cruz/2024 409 1 Copy Concepts And Approaches In Inventory Management And Control/banaag, Et.al/2024 410 1 Copy Entrepreneurial Behavior Growth Mindset And Fixed Mindset/pasahol, Et.al/2024 411 1 Copy Essentials Of Risk Management/banaag/2024 412 1 Copy Front Office System And Procedures, Rev. Ed./lago, Lim/2024 413 1 Copy Handbook In Juvenile Deliquency And Violence Againts Women And Their Children/boholona, Et. Al/2024 414 1 Copy Moral Philosophy And Ethics/bacuyag/2024 415 1 Copy Multicultural Diversity In The Tourism Hospitality Workplace: A Comprehensive Guide For Professionals/maranan, Et.al/2024 416 1 Copy (path-fit 2) Physical Activity Towards Health And Fitness Rhytmic Dance And Social Activities/punzalan, Habana/2024 417 1 Copy Promoting Community Change Through Civic Welfare Training Service 2/briones, Et.al/2024 418 1 Copy Strategic Management In Tourism And Hospitality Industry/buenaventura,gutierrez/2024 419 1 Copy Sustanable Tourism: A Comprehensive Guide To Promoting Responsible Travel/maranan, Et.al/2024 420 1 Copy The Teaching Profession In The 21st Century/sarandi, Babao/2024 421 1 Copy Teaching And Assessment Of Grammar/manas/2024 422 1 Copy Understanding Society And Culture/riodique Iii/2024 423 1 Copy Vice And Drug Education And Control /tad-awan,et Al./2024 424 1 Copy Juvenile Delinquency And Juvenile Justice System 2nd Ed./detran/2024 425 1 Copy Introduction To Philippine Government & Politics With Basic Constitutional Provisions/baes/2024 426 1 Copy Human Development-understanding Criminal Behavior And Victimology/togana/2024 Canique Library 427 1 Copy Entrepreneurial Behavior Growth Mindset And Fixed Mindset/pasahol, Et.al/2024 428 1 Copy An Eye For Art Appreciation: Perception And Expression,2nd Ed./sonsona, Et.al/2024 429 1 Copy Gender And Society/bacolod, Et.al/2024 430 1 Copy Introduction To Philippine Government & Politics With Basic Constitutional Provisions/baes/2024 431 1 Copy The Life And Works Of Rizal/sanchez, Et.al/2024 432 1 Copy The Contemporary World//mananay, Et.al/2024 433 1 Copy Understanding Society And Culture/riodique Iii/2024 434 1 Copy Upscaling Oral Communicationskills In The 21st Century Global Space/gutierrez, Et Al/2024 435 1 Copy Organic Farming/loreto/2021 436 1 Copy Organic Fungicides/loreto/2021 437 1 Copy Organic Gardening/loreto/2021 438 1 Copy Mathematics In Modern World/reynoso, C./2024 439 1 Copy Nstp 1 Guide In Civic Welfare Training Service/lonez/2023 440 1 Copy Physical Activity Towards Health & Fitness 1 (path-fit 1) Health & Wellness, Movement Education And Exercise Program/punzalan,et Al/2023 441 1 Copy Physical Activities Towards Health And Fitness( Pathfit 2) Combative Sports & Outdoor Recreational Activities/bulatao, Et Al/2023 442 1 Copy Biological Chemistry Obe-based/chua,et.al/2023 Culion Library 443 1 Copy Understanding Society And Culture/riodique Iii/2024 444 2 Copy Upscaling Oral Communicationskills In The 21st Century Global Space/gutierrez, Et Al/2024 445 1 Copy Organic Farming/loreto/2021 446 1 Copy Organic Fungicides/loreto/2021 447 1 Copy Organic Gardening/loreto/2021 448 1 Copy Mathematics In Modern World/reynoso, C./2024 449 1 Copy Nstp 1 Guide In Civic Welfare Training Service/lonez/2023 450 1 Copy Physical Activity Towards Health & Fitness 1 (path-fit 1) Health & Wellness, Movement Education And Exercise Program/punzalan,et Al/2023 451 1 Copy Physical Activities Towards Health And Fitness( Pathfit 2) Combative Sports & Outdoor Recreational Activities/bulatao, Et Al/2023 452 1 Copy Biological Chemistry Obe-based/chua,et.al/2023 453 1 Copy Entrepreneurial Behavior Growth Mindset And Fixed Mindset/pasahol, Et.al/2024 454 1 Copy An Eye For Art Appreciation: Perception And Expression,2nd Ed./sonsona, Et.al/2024 455 1 Copy Gender And Society/bacolod, Et.al/2024 456 1 Copy Introduction To Philippine Government & Politics With Basic Constitutional Provisions/baes/2024 457 1 Copy The Life And Works Of Rizal/sanchez, Et.al/2024 458 1 Copy The Contemporary World//mananay, Et.al/2024 Rio Tuba Library 459 1 Copy Mathematics In Modern World/reynoso, C./2024 460 1 Copy Art Appreciation 2e/sanchez,et.al/2023 461 1 Copy Art Appreciation For College Students/leano/2018 462 1 Copy Ethics/mondares,r/2024 463 1 Copy Understading The Self/vazquez, I./2024 464 1 Copy Environmental Science For All/cobar, L./2022 465 1 Copy Environmental Science/calimlim/2021 466 1 Copy Nstp 1 Guide In Civic Welfare Training Service/lonez/2023 467 1 Copy Physical Activity Towards Health & Fitness 1 (path-fit 1) Health & Wellness, Movement Education And Exercise Program/punzalan,et Al/2023 468 1 Copy Physical Activities Towards Health And Fitness( Pathfit 2) Combative Sports & Outdoor Recreational Activities/bulatao, Et Al/2023 469 2 Copy Physical Activities Towards Health And Fitness Pathfit 2( Exercise-based Fitness Activities/ballecer,et Al/2023 470 2 Copy Physical Activity Towards Health And Fitness 3 (path-fit 3 )menu Of Dance/punzalan, Et Al./2023 471 2 Copy Physical Activity Towards Health And Fitness ( Path-fit 4 Sports)individual/dual And Team Sports/bulatao, Et Al/2023

Details: Description S P E C I F I C A T I O N S B.5 Project Billboard The Contractor Shall Install One (1) Billboard Measuring 8 Ft. X 8 Ft. Tarpaulin, In Front Of The Project Site. Project Billboard Shall Be Installed For Government Information Projects To Inform The Public Of The Implementation Of The Project And To Advise The Road Users Of The On-going Construction. Upon Completion Of The Work, All Signs Installed Shall Be Removed From The Site. 102(1) Roadway Excavation Removal Of Unsuitable Material Where The Plans Show The Top Portion Of The Roadbed To Be Selected Topping, All Unsuitable Materials Shall Be Excavated To The Depth Necessary For Replacement Of The Selected Topping To The Required Compacted Thickness. Where Excavation To The Finished Graded Section Results In A Subgrade Or Slopes Of Unsuitable Soil, The Engineer May Require The Contractor To Remove The Unsuitable Material And Backfill To The Finished Graded Section With Approved Material. The Contractor Shall Conduct His Operations In Such A Way That The Engineer Can Take The Necessary Cross-sectional Measurements Before The Backfill Is Placed. The Excavation Of Muck Shall Be Handled In A Manner That Will Not Permit The Entrapment Of Muck Within The Backfill. The Material Used For Backfilling Up To The Ground Line Or Water Level, Whichever Is Higher, Shall Be Rock Or Other Suitable Granular Material Selected From The Roadway Excavation, If Available. If Not Available, Suitable Material Shall Be Obtained From Other Approved Sources. Unsuitable Material Removed Shall Be Disposed Off In Designated Areas Shown On The Plans Or Approved By The Engineer. Item 201 – Aggregate Base Course 201.1 Description This Item Shall Consist Of Furnishing, Placing And Compacting An Aggregate Base Course On A Prepared Sub-grade/sub-base In Accordance With This Specification And The Lines, Grades, Thickness And Typical Cross-sections Shown On The Plans, Or As Established By The Lgu Project Engineer. 201.2 Material Requirements Aggregate For Base Course Shall Consist Of Hard, Durable Particles Or Fragments Of Crushed Stone, Crushed Slag Or Crushed Or Natural Gravel And Filler Of Natural Or Crushed Sand Or Other Finely Divided Mineral Matter. The Composite Material Shall Be Free From Vegetable Matter And Lumps Or Balls Of Clay, And Shall Be Of Such Nature That It Can Be Compacted Readily To Form A Firm, Stable Base. In Some Areas Where The Conventional Base Course Materials Are Scarce Or Non-available, The Use Of 40% Weathered Limestone Blended With 60% Crushed Stones Or Gravel Shall Be Allowed, Provided That The Blended Materials Meet The Requirements Of This Item. The Base Course Material Shall Conform To Table 201.1, Whichever Is Called For In The Bill Of Quantities Table 201.1 – Grading Requirements Sieve Designation Mass Percent Passing Standard, Mm Alternate Us Standard Grading A Grading B 50 2” 100 37.5 1-1/2” - 100 25.0 1” 60 – 85 - 19.0 ¾” - 60 – 85 12.5 ½” 35 – 65 - 4.75 No. 4 20 – 50 30 – 55 0.425 No. 40 5 – 20 8 – 25 0.075 No. 200 0 – 12 2 – 14 The Fraction Passing The 0.075 Mm (no. 200) Sieve Shall Not Be Greater Than 0.66 (two Thirds) Of The Fraction Passing The 0.425 Mm (no. 40) Sieve. The Fraction Passing The 0.425 Mm (no. 40) Sieve Shall Have A Liquid Limit Not Greater Than 25 And Plasticity Index Not Greater Than 6 As Determined By Aashto T 89 And T 90, Respectively. The Coarse Portion, Retained On A 2.00 Mm (no. 10) Sieve Shall Have A Mass Percent Of Wear Not Exceeding 50 By The Los Angeles Abrasion Test Determined By Aashto T 96. The Material Passing The 19 Mm (3/4 Inch) Sieve Shall Have A Soaked Cbr Value Of Not Less Than 80% As Determined By Aashto T 193. The Cbr Value Shall Be Obtained At The Maximum Dry Density (mdd) As Determined By Aashto T 180, Method D. If Filler, In Addition To That Naturally Present, Is Necessary For Meeting The Grading Requirements Or For Satisfactory Bonding, It Shall Be Uniformly Blended With The Base Course Material On The Road Or In A Pug Mill Unless Otherwise Specified Or Approved. Filler Shall Be Taken From Sources Approved By The Lgu Project Engineer, Shall Be Free From Hard Lumps And Shall Not Contain More Than 15 Percent Of Material Retained On The 4.75 Mm (no. 4) Sieve. 201.3 Construction Requirements 201.3.1 Preparation Of Existing Surface The Existing Surface Shall Be Graded And Finished As Provided Under Item 105, Sub-grade Preparation, Before Placing The Base Material. 201.3.2 Placing It Shall Be In Accordance With All The Requirements Of Subsection 200.3.2, Placing. 201.3.3 Spreading And Compacting It Shall Be In Accordance With All The Requirements Of Subsection 200.3.3, Spreading And Compacting. 201.3.4 Additional Filler Additional Filler, When Required And When Not Added At The Screening Plant, Shall Be Spread In A Uniform Layer Over The Loosely Spread Base Material As Specified By The Lgu Project Engineer, Scarified By Appropriate Heavy Equipment And Then Watered And Mixed As Described Above. These Materials Are Incidental To The Work And No Payment Shall Be Made By The Project To The Contractor. 201.3.5 Trial Sections Trial Sections Shall Conform In All Respects To The Requirements Specified In Subsection 200.3.4. 201.3.6 Tolerances The Aggregate Base Course Shall Be Laid To The Designed Level And Transverse Slopes Shown On The Plans. The Allowable Tolerances Shall Be In Accordance With Following: Permitted Variation From Design Thickness Of Layer ± 10 Mm Permitted Variation From Design Level Of Surface + 5 Mm -10 Mm Permitted Surface Irregularity Measured By 3-m Straight-edge 5 Mm Permitted Variation From Design Crossfall Or Camber ± 0.2% Permitted Variation From Design Longitudinal Grade Over 25 M In Length ± 0.1% 201.4 Environmental Measures During The Course Of Hauling Operations, The Contractor Must At All Times Provide The Necessary Cover For The Dump Body Of The Hauling Equipment To Prevent Accidental Spoilage Of Earth Materials That Will Injure The Travelling Public Or People Living Near By. The Travel Route Of The Hauling Equipment’s Must Always Be Moist To Prevent Blowing Up Of Dusts Particles. Likewise, The Contractor Must Always Observe The Noise Level Of The Exhaust Mufflers Of The Heavy Equipment’s To Be At Minimum. Otherwise, Exhaust Muffler Must Be Provided With Silencers To Reduce Noise Levels Of The Hauling Equipment’s. Travelling Speed Of All Hauling Equipment’s Must Be Reduce When Passing Populated Areas Or At The School Site During School Days. Item 311 – Portland Cement Concrete Pavement 311.1 Description This Item Shall Consist Of Pavement Of Portland Cement Concrete, With Or Without Reinforcement, Constructed On The Prepared Base In Accordance With This Specification And In Conformity With Lines, Grades, Thickness And Typical Cross-section Shown On The Plans. 311.2 Material Requirements 311.2.1 Portland Cement Only Type I Portland Cement Shall Be Used Unless Otherwise Provided For In The Special Provisions. Different Brands Or The Same Brands From Different Mills Shall Not Be Mixed Nor Shall They Be Used Alternately Unless The Mix Is Approved By The Lgu Project Engineer. Cement Which For Any Reason Has Become Partially Set Or Which Contains Lumps Of Caked Cement Will Be Rejected. Cement Salvaged From Discarded Or Used Bags Shall Not Be Used. Samples Of Cement Shall Be Obtained In Accordance With Aashto T 127. 311.2.2 Fine Aggregate It Shall Consist Of Natural Sand, Stone Screenings Or Other Inert Materials With Similar Characteristics, Or Combinations Thereof, Having Hard, Strong And Durable Particles. Fine Aggregate From Different Sources Of Supply Shall Not Be Mixed Or Stored In The Same Pile Nor Used Alternately In The Same Class Of Concrete Without The Approval Of The Lgu Project Engineer. It Shall Not Contain More Than Three (3) Mass Percent Of Material Passing The 0.075 Mm (no. 200 Sieve) By Washing Nor More Than One (1) Mass Percent Each Of Clay Lumps Or Shale. The Use Of Beach Sand Will Not Be Allowed Without The Approval Of The Lgu Project Engineer. If The Fine Aggregate Is Subjected To Five (5) Cycles Of The Sodium Sulfate Soundness Test, The Weighted Loss Shall Not Exceed 10 Mass Percent. The Fine Aggregate Shall Be Free From Injurious Amounts Of Organic Impurities. If Subjected To The Colorimetric Test For Organic Impurities And A Color Darker Than The Standard Is Produced, It Shall Be Rejected. However, When Tested For The Effect Of Organic Impurities Of Strength Of Mortar By Aashto T 71, The Fine Aggregate May Be Used If The Relative Strength At 7 And 28 Days Is Not Less Than 95 Mass Percent. The Fine Aggregate Shall Be Well-graded From Coarse To Fine And Shall Conform To Table 311.1 Table 311.1 – Grading Requirements For Fine Aggregate Sieve Designation Mass Percent Passing 9.5 Mm (3/8 In) 100 4.75 Mm (no. 4) 95 – 100 2.36 Mm (no. 8) - 1.18 Mm (no. 16) 45 – 80 0.600 Mm (no. 30) - 0.300 Mm (no. 50) 5 – 30 0.150 Mm (no. 100) 0 – 10 311.2.3 Coarse Aggregate It Shall Consist Of Crushed Stone, Gravel, Blast Furnace Slag, Or Other Approved Inert Materials Of Similar Characteristics, Or Combinations Thereof, Having Hard, Strong, Durable Pieces And Free From Any Adherent Coatings. It Shall Contain Not More Than One (1) Mass Percent Of Material Passing The 0.075 Mm (no. 200) Sieve, Not More Than 0.25 Mass Percent Of Clay Lumps, Nor More Than 3.5 Mass Percent Of Soft Fragments. If The Coarse Aggregate Is Subjected To Five (5) Cycles Of The Sodium Sulfate Soundness Test, The Weighted Loss Shall Not Exceed 12 Mass Percent. It Shall Have A Mass Percent Of Wear Not Exceeding 40 When Tested By Aashto T 96. If The Slag Is Used, Its Density Shall Not Be Less Than 1120 Kg/m3 (70 Lb./cu. Ft.). The Gradation Of The Coarse Aggregate Shall Conform To Table 311.2. Only One Grading Specification Shall Be Used From Any One Source. Table 311.2 – Grading Requirement For Coarse Aggregate Sieve Designation Mass Percent Passing Standard Mm Alternate U. S. Standard Grading A Grading B Grading C 75.00 3 In. 100 - - 63.00 2-1/2 In. 90-100 100 100 50.00 2 In. - 90-100 95-100 37.5 1-1/2 In. 25-60 35-70 - 25.0 1 In. - 0-15 35-70 19.0 ¾ In. 0-10 - - 12.5 ½ In. 0-5 0-5 10-30 4.75 No. 4 - - 0-5 311.2.4 Water Water Used In Mixing, Curing Or Other Designated Application Shall Be Reasonably Clean And Free Of Oil, Salt, Acid, Alkali, Grass Or Other Substances Injurious To The Finished Product. Water Will Be Tested In Accordance With And Shall Meet The Requirements Of Item 714, Water. Water Which Is Drinkable May Be Used Without Test. Where The Source Of Water Is Shallow, The Intake Shall Be So Enclosed As To Exclude Silt, Mud, Grass Or Other Foreign Materials. 311.2.5 Reinforcing Steel It Shall Conform To The Requirements Of Item 404, Reinforcing Steel. Dowels And Tie Bars Shall Conform To The Requirements Of Aashto M 31 Or M 42, Except That Rail Steel Shall Not Be Used For Tie Bars That Are To Be Bent And Re-straightened During Construction. Tie Bars Shall Be Deformed Bars. Dowels Shall Be Plain Round Bars. Before Delivery To The Site Of Work, One-half Of The Length Of Each Dowel Shall Be Painted With One Coat Of Approved Lead Or Tar Paint. The Sleeves For Dowel Bars Shall Be Metal Of Approved Design To Cover 50 Mm ( 2 Inches), Plus Or Minus 5 Mm (1/4 Inch) Of The Dowel, With A Closed End, And With A Suitable Stop To Hold The End Of The Sleeve At Least 25 Mm (1 Inch) From The End Of The Dowel. Sleeves Shall Be Of Such Design That They Do Not Collapse During Construction. 311.2.6 Joint Fillers Poured Joint Fillers Shall Be Mixed Asphalt And Mineral Or Rubber Filler. Preformed Joint Filler Shall Conform To The Applicable Requirements. It Shall Be Punched To Admit The Dowels Where Called For In The Plans. The Filler For Each Joint Shall Be Furnished In A Single Piece For The Full Depth And Width Required For The Joint. 311.2.7 Admixtures Air-entraining Admixture Shall Conform To The Requirements Of Aashto M 154. Chemical Admixtures, If Specified Or Permitted, Shall Conform To The Requirements Of Aashto M 194. Fly Ash, If Specified Or Permitted As A Mineral Admixture And As 20% Partial Replacement Of Portland Cement In Concrete Mix Shall Conform To The Requirements Of Astm C 618. Admixture Should Be Added Only To The Concrete Mix To Produce Some Desired Modifications To The Properties Of Concrete Where Necessary, But Not As Partial Replacement Of Cement. 311.2.8 Curing Materials Curing Materials Shall Conform To The Following Requirements As Specified; A) Burlap Cloth - Aashto M 182 B) Liquid Membrane Forming Compounds - Aashto M 148 C) Sheeting (film) Materials - Aashto M 171 Cotton Mats And Water-proof Paper Can Be Used. 311.2.9 Calcium Chloride/calcium Nitrate It Shall Conform To Aashto M 144, If Specified Or Permitted By The Lgu Project Engineer, As Accelerator. 311.2.10 Storage Of Cement And Aggregate All Cement Shall Be Stored, Immediately Upon Delivery At The Site, In Weatherproof Building Which Will Protect The Cement From Dampness. The Floor Shall Be Raised From The Ground. The Buildings Shall Be Placed In Locations Approved By The Lgu Project Engineer. Provisions For Storage Shall Be Ample, And The Shipments Of Cement As Received Shall Be Separately Stored In Such A Manner As To Allow The Earliest Deliveries To Be Used First And To Provide Easy Access For Identification And Inspection Of Each Shipment. Storage Buildings Shall Have Capacity For Storage Of A Sufficient Quantity Of Cement To Allow Sampling At Least Twelve (12) Days Before The Cement Is To Be Used. Bulk Cement, If Used, Shall Be Transferred To Elevated Air Tight And Weatherproof Bins. Stored Cement Shall Meet The Test Requirements At Any Time After Storage When Retest Is Ordered By The Lgu Project Engineer. At The Time Of Use, All Cement Shall Be Free-flowing And Free Of Lumps. The Handling And Storing Of Concrete Aggregates Shall Be Such As To Prevent Segregation Or The Inclusion Of Foreign Materials. The Lgu Project Engineer May Require That Aggregates Be Stored On Separate Platforms At Satisfactory Locations. In Order To Secure Greater Uniformity Of Concrete Mix, The Lgu Project Engineer May Require That The Coarse Aggregate Be Separated Into Two Or More Sizes. Different Sizes Of Aggregate Shall Be Stored In Separate Bins Or In Separate Stockpiles Sufficiently Removed From Each Other To Prevent The Material At The Edges Of The Piles From Becoming Intermixed. 311.2.11 Proportioning, Consistency And Strength Of Concrete The Contractor Shall Prepare The Design Mix Based On The Absolute Volume Method As Outlined In The American Concrete Institute (aci) Standard 211.1, “recommended Practice For Selecting Proportions For Normal And Heavyweight Concrete”. It Is The Intent Of This Specification To Require At Least 364 Kg Of Cement Per Cubic Meter Of Concrete To Meet The Minimum Strength Requirements. The Lgu Project Engineer Shall Determine From Laboratory Tests Of The Materials To Be Used, The Cement Content And The Proportions Of Aggregate And Water That Will Produce Workable Concrete Having A Slump Of Between 40 And 75 Mm (1-1/2 And 3 Inches) If Not Vibrated Or Between 10 And 40 Mm (1/2 And 1-1/2 Inches) If Vibrated, And A Flexural Strength Of Not Less Than 3.8 Mpa (550 Psi) When Tested By The Third-point Method Or 4.5 Mps (650 Psi) When Tested By The Mid-point Method At Fourteen (14) Days In Accordance With Aashto T97 And T177, Respectively; Or A Compressive Strength Of 24.1 Mps (3500 Psi) For Cores Taken At Fourteen (14) Days And Tested In Accordance With Aashto T24. Slump Shall Be Determined Using Aashto T 119. The Designer Shall Consider The Use Of Lean Concrete (econcrete) Mixtures Using Local Materials Or Specifically Modified Conventional Concrete Mixes In Base Course And In The Lower Course Composite, Monolithic Concrete Pavements Using A Minimum Of 75 Mm (3 Inches) Of Conventional Concrete As The Surface Course. The Mix Design Shall Be Submitted To The Lgu Project Engineer For Approval And Shall Be Accompanied With Certified Test Data From An Approved Laboratory Demonstrating The Adequacy Of The Mix Design. A Change In The Source Of Materials During The Progress Of Work May Necessitate A New Design Mix. 311.3 Construction Requirements 311.3.1 Quality Control Of Concrete 1. General The Contractor Shall Be Responsible For The Quality Control Of All Materials During The Handling, Blending, And Mixing And Placement Operations. 2. Quality Control Plan The Contractor Shall Furnish The Lgu Project Engineer A Quality Control Plan Detailing His Production Control Procedures And The Type And Frequency Of Sampling And Testing To Insure That The Concrete Produces Complies With The Specifications. The Lgu Project Engineer Shall Be Provided Free Access To Recent Plant Production Records, And If Requested, Informational Copies Of Mix Design, Materials Certifications And Sampling And Testing Reports. 3. Qualification Of Workmen Experienced And Qualified Personnel Shall Perform All Batching Or Mixing Operation For The Concrete Mix, And Shall Be Present At The Plant And Job Site To Control The Concrete Productions Whenever The Plant Is In Operation. They Shall Be Identified And Duties Defined As Follows: A. Concrete Batcher. The Person Performing The Batching Or Mixing Operation Shall Be Capable Of Accurately Conducting Aggregate Surface Moisture Determination And Establishing Correct Scale Weights For Concrete Materials. He Shall Be Capable Of Assuring That The Proportioned Batch Weights Of Materials Are In Accordance With The Mix Design. B. Concrete Technician. The Person Responsible For Concrete Production Control And Sampling And Testing For Quality Control Shall Be Proficient In Concrete Technology And Shall Have A Sound Knowledge Of The Specifications As They Relate To Concrete Production. He Shall Be Capable Of Conducting Tests On Concrete And Concrete Materials In Accordance With These Specifications. He Shall Be Capable Of Adjusting Concrete Mix Designs For Improving Workability And Specification Compliance And Preparing Trial Mix Designs. He Shall Be Qualified To Act As The Concrete Batcher In The Batcher’s Absence. 4. Quality Control Testing The Contractor Shall Perform All Sampling, Testing And Inspection Necessary To Assure Quality Control Of The Component Materials And The Concrete. The Contractor Shall Be Responsible For Determining The Gradation Of Fine And Coarse Aggregates And For Testing The Concrete Mixture For Slump, Air Content, Water-cement Ratio And Temperature. He Shall Conduct His Operations So As To Produce A Mix Conforming To The Approved Mix Design. 5. Documentation The Contractor Shall Maintain Adequate Records Of All Inspections And Tests. The Records Shall Indicate The Nature And Number Of Observations Made, The Number And Type Of Deficiencies Found, The Quantities Approved And Rejected, And Nature Of Any Corrective Action Taken. The Lgu Project Engineer May Take Independent Assurance Samples At Random Location For Acceptance Purposes As He Deems Necessary. 311.3.2 Equipment Equipment And Tools Necessary For Handling Materials And Performing All Parts Of The Work Shall Be Approved By The Lgu Project Engineer As To Design, Capacity And Mechanical Condition. The Equipment Shall Be At The Jobsite Sufficiently Ahead Of The Start Of Construction Operations To Be Examined Thoroughly And Approved. 1. Batching Plant And Equipment A. General. The Batching Shall Include Bins, Weighing Hoppers, And Scales For The Fine Aggregate And For Each Size Of Coarse Aggregate. If Cement Is Used In Bulk, A Bin, A Hopper, And Separate Scale For Cement Shall Be Included. The Weighing Hopper Shall Be Properly Sealed And Vented To Preclude Dusting Operation. The Batch Plant Shall Be Equipped With A Suitable Non-resettable Batch Counter Which Will Correctly Indicate The Number Of Batches Proportioned. B. Bins And Hoppers. Bins With Adequate Separate Compartments For Fine Aggregate And For Each Size Of Coarse Aggregate Shall Be Provided In The Batching Plant. C. Scales. Scales For Weighing Aggregates And Cement Shall Be Of Either The Beam Type Or The Spring-less-dial Type. They Shall Be Accurate Within One-half Percent (0.5%) Throughout The Range Of Use. Poises Shall Be Designed To Be Locked In Any Position And To Prevent Unauthorized Change. Scales Shall Be Inspected And Sealed As Often As The Lgu Project Engineer May Deem Necessary To Assure Their Continued Accuracy. D. Automatic Weighing Devices. Unless Otherwise Allowed On The Contract, Batching Plants Shall Be Equipped With Automatic Weighing Devices Of An Approved Type To Proportion Aggregates And Bulk Cement. 2. Mixers. A. General. Concrete May Be Mixed At The Site Of Construction Or At A Central Plant, Or Wholly Or In Part In Truck Mixers. Each Mixer Shall Have A Manufacturer’s Plate Attached In A Prominent Place Showing The Capacity Of The Drum In Terms Of Volume Of Mixed Concrete And The Speed Of Rotation Of The Mixing Drum Or Blades. B. Mixers At Site Of Construction. Mixing Shall Be Done In An Approved Mixer Capable Of Combining The Aggregates, Cement And Water Into A Thoroughly Mixed And Uniform Mass Within The Specified Mixing Period And Discharging And Distributing The Mixture Without Segregation On The Prepared Grade. The Mixer Shall Be Equipped With An Approved Timing Device Which Will Automatically Lock The Discharge Lever When The Drum Has Been Charged And Released It At The End Of The Mixing Period. In Case Of Failure Of The Timing Device, The Mixer May Be Used For The Balance Of The Day While It Is Being Repaired, Provided That Each Batch Is Mixed 90 Seconds. The Mixer Shall Be Equipped With A Suitable Non-resettable Batch Counter Which Shall Correctly Indicate The Number Of The Batches Mixed. C. Truck Mixer And Truck Agitators. Truck Mixers Used For Mixing And Hauling Concrete, And Truck Agitators Used For Hauling Central-mixed Concrete, Shall Conform To The Requirements Of Aashto M 157. D. Non-agitator Truck. Bodies Of Non-agitating Hauling Equipment For Concrete Shall Be Smooth, Mortar-tight Metal Containers And Shall Be Capable Of Discharging The Concrete At A Satisfactory Controlled Rate Without Segregation. 3. Paving And Finishing Equipment The Concrete Shall Be Placed With An Approved Paver Designed To Spread, Consolidate, Screed And Float Finish The Freshly Placed Concrete In One Complete Pass Of The Machine In Such A Manner That A Minimum Of Hand Finishing Will Be Necessary To Provide A Dense And Homogeneous Pavement In Conformance With The Plans And Specifications. The Finishing Machine Shall Be Equipped With At Least Two (2) Oscillating Type Transverse Screed. Vibrators Shall Operate At A Frequency Of 8,300 To 9,600 Impulses Per Minute Under Load At A Maximum Spacing Of 60 Cm. 4. Concrete Saw The Contractor Shall Provide Sawing Equipment In Adequate Number Of Units And Power To Complete The Sawing With Water-cooled Diamond Edge Saw Blade Or An Abrasive Wheel To The Required Dimensions And At The Required Rate. He Shall Provide At Least One (1) Stand-by Saw In Good Working Condition And With An Ample Supply Of Saw Blades. 5. Forms Forms Shall Be Of Steel, Of An Approved Section, And Of Depth Equal To The Thickness Of The Pavement At The Edge. The Base Of The Forms Shall Be Of Sufficient Width To Provide Necessary Stability In All Directions. The Flange Braces Must Extend Outward On The Base To Not Less Than 2/3 The Height Of The Form. All Forms Shall Be Rigidly Supported On Bed Of Thoroughly Compacted Material During The Entire Operation Of Placing And Finishing The Concrete. Forms Shall Be Provided With Adequate Devices For Secure Setting So That When In Place, They Will Withstand, Without Visible Spring Or Settlement, The Impact And Vibration Of The Consolidation And Finishing Or Paving Equipment. 311.3.3 Preparation Of Grade After The Sub-grade Of Base Has Been Placed And Compacted To The Required Density, The Areas Which Will Support The Paving Machine And The Grade On Which The Pavement Is To Be Constructed Shall Be Trimmed To The Proper Elevation By Means Of A Properly Designed Machine Extending The Prepared Work Areas Compacted At Least 60 Cm Beyond Each Edge Of The Proposed Concrete Pavement. If Loss Of Density Results From The Trimming Operations, It Shall Be Restored By Additional Compaction Before Concrete Is Placed. If Any Traffic Is Allowed To Use The Prepared Sub-grade Or Base, The Surface Shall Be Checked And Corrected Immediately Ahead Of The Placing Concrete. The Sub-grade Or Base Shall Be Uniformly Moist When The Concrete Is Placed. 311.3.4 Setting Forms 1. Base Support. The Foundation Under The Forms Shall Be Hard And True To Grade So That The Form When Set Will Be Firmly In Contact For Its Whole Length And At The Specified Grade. (any Roadbed, Which At The Form Line Is Found Below Established Grade, Shall Be Filled With Approved Granular Materials To Grade In Lifts Of Three (3) Cm Or Less, And Thoroughly Re-rolled Or Tamped.) Imperfections Or Variations Above Grade Shall Be Corrected By Tamping Or By Cutting As Necessary. 2. Form Setting Forms Shall Be Set Sufficiently In Advance Of The Point Where Concrete Is Being Placed. After The Forms Have Been Set To Correct Grade, The Grade Shall Be Thoroughly Tamped, Mechanically Or By Hand, At Both The Inside And Outside Edges Of The Base Of The Forms. The Forms Shall Not Deviate From True Line Bv More Than One (1) Cm At Any Point. 3. Grade And Alignment The Alignment And Grade Elevations Of The Forms Shall Be Checked And Corrections Made By The Contractor Immediately Before Placing The Concrete. Testing As To Crown And Elevation, Prior To Placing Of Concrete Can Be Made By Means Of Holding An Approved Template In A Vertical Position And Moved Backward And Forward On The Forms. When Any Form Has Been Disturbed Or Any Grade Has Become Unstable, The Form Shall Be Reset And Rechecked. 311.3.5 Conditioning Of Sub-grade Or Base Course When Side Forms Have Been Securely Set To Grade, The Sub-grade Or Base Course Shall Be Brought To Proper Cross-section. High Areas Shall Be Trimmed To Proper Elevation. Low Areas Shall Be Filled And Compacted To A Condition Similar To That Of Surrounding Grade. The Finished Grade Shall Be Maintained In A Smooth And Compacted Condition Until The Pavement Is Placed. Unless Waterproof Sub-grade Or Base Course Cover Material Is Specified, The Sub-grade Or Base Course Shall Be Uniformly Moist When The Concrete Is Placed. If It Subsequently Becomes Too Dry, The Sub-grade Or Base Course Shall Be Sprinkled, But The Method Of Sprinkling Shall Not Be Such As To Form Mud Or Pools Of Water. 311.3.6 Handling, Measuring And Batching Materials The Batch Plant Site, Layout, Equipment And Provisions For Transporting Material Shall Be Such As To Assure A Continuous Supply Of Material To The Work. Stockpiles Shall Be Built Up In Layers Of Not More Than One (1) Meter In Thickness. Each Layer Shall Be Completely In Place Before Beginning The Next Which Shall Not Be Allowed To “cone” Down Over The Next Lower Layer. Aggregates From Different Sources And Of Different Grading Shall Not Be Stockpiled Together. All Washed Aggregates And Aggregates Produced Or Handled By Hydraulic Methods, Shall Be Stockpiled Or Binned For Draining At Least Twelve (12) Hours Before Being Batched. When Mixing Is Done At The Side Of The Work, Aggregates Shall Be Transported From The Batching Plant To The Mixer In Batch Boxes, Vehicle Bodies, Or Other Containers Of Adequate Capacity And Construction To Properly Carry The Volume Required. Partitions Separating Batches Shall Be Adequate And Effective To Prevent Spilling From One Compartment To Another While In Transit Or Being Dumped. When Bulk Cement Is Used, The Contractor Shall Use A Suitable Method Of Handling The Cement From Weighing Hopper To Transporting Container Or Into The Batch Itself For Transportation To The Mixer, With Chute, Boot Or Other Approved Device, To Prevent Loss Of Cement, And To Provide Positive Assurance Of The Actual Presence In Each Batch Of The Entire Cement Content Specified. Bulk Cement Shall Be Transported To The Mixer In Tight Compartments Carrying The Full Amount Of Cement Required For The Batch. However, If Allowed In The Special Provisions, It May Be Transported Between The Fine And Coarse Aggregate. When Cement Is Placed In Contact With The Aggregates, Batches May Be Rejected Unless Mixed Within 1-1/2 Hours Of Such Contact. Cement In Original Shipping Packages May Be Transported On Top Of The Aggregates, Each Batch Containing The Number Of Sacks Required By The Job Mix. The Mixer Shall Be Charged Without Loss Of Cement. Batching Shall Be So Conducted As To Result In The Weight To Each Material Required Within A Tolerance Of One (1) Percent For The Cement And Two (2) Percent For Aggregates. Water May Be Measured Either By Volume Or By Weight. The Accuracy Of Measuring The Water Shall Be Within A Range Of Error Of Not Over Than One (1) Percent. Unless The Water Is To Be Weighed, The Water-measuring Equipment Shall Include An Auxiliary Tank From Which The Measuring Tank Shall Be Equipped With An Outside Tap And Valve To Provide Checking The Setting, Unless Other Means Are Provided For Readily And Accurately Determining The Amount Of Water In The Tank. The Volume Of The Auxiliary Tank Shall Be At Least Equal To That Of The Measuring Tank. 311.3.7 Mixing Concrete The Concrete May Be Mixed At The Site Of The Work In A Central-mix Plant, Or In Truck Mixers. The Mixer Shall Be Of An Approved Type And Capacity. Mixing Time Will Be Measured From The Time All Materials, Except Water, Are In The Drum. Ready-mixed Concrete Shall Be Mixed And Delivered In Accordance With Requirements Of Aashto M 157, Except That The Minimum Required Revolutions At The Mixing Speed For Transit-mixed Concrete May Be Reduced To Not Less Than That Recommended By The Mixer Manufacturer. The Number Of Revolutions Recommended By The Mixer Manufacturer Shall Be Indicated On The Manufacturer’s Serial Plate Attached To The Mixer. The Contractor Shall Furnish Test Data Acceptable To The Lgu Project Engineer Verifying That The Make And Model Of The Mixer Will Produce Uniform Concrete Conforming To The Provision Of Aashto M 157 At The Reduced Number Of Revolutions Shown On The Serial Plate. When Mixed At The Site Or In A Central Mixing Plant, The Mixing Time Shall Not Be Less Than Fifty (50) Seconds Nor More Than Ninety (90) Seconds, Unless Mixer Performance Tests Prove Adequate Mixing Of The Concrete Is A Shorter Time Period. Four (4) Seconds Shall Be Added To The Specified Mixing Time If Timing Starts At The Instant The Skip Reaches Its Maximum Raised Positions. Mixing Time Ends When The Discharge Chute Opens. Transfer Time In Multiple Drum Mixers Is Included In Mixing Time. The Contents Of An Individual Mixer Drum Shall Be Removed Before A Succeeding Batch Is Emptied Therein. The Mixer Shall Be Operated At The Drum Speed As Shown On The Manufacturer’s Name Plate Attached On The Mixer. Any Concrete Mixed Less Than The Specified Time Shall Be Discarded And Disposed Off By The Contractor At His Expense. The Volume Of Concrete Mixed Per Batch Shall Not Exceed The Mixer’s Nominal Capacity In Cubic Metre, As Shown On The Manufacturer’s Standard Rating Plate On The Mixer, Except That An Overload Up To Ten (10) Percent Above The Mixer’s Nominal Capacity May Be Permitted Provided Concrete Test Data For Strength, Segregation, And Uniform Consistency Are Satisfactory, And Provided No Spillage Of Concrete Takes Place. The Batches Shall Be So Charged Into The Drum That A Portion Of The Mixing Water Shall Be Entered In Advance Of The Cement And Aggregates. The Flow Of Water Shall Be Uniform And All Water Shall Be In The Drum By The End Of The First Fifteen (15) Seconds Of The Mixing Period. The Throat Of The Drum Shall Be Kept Free Of Such Accumulations As May Restrict The Free Flow Of Materials Into The Drum. Mixed Concrete From The Central Mixing Plant Shall Be Transported In Truck Mixers, Truck Agitators Or Non-agitating Truck Specified In Subsection 311.3.2, Equipment. The Time Elapsed From The Time Water Is Added To The Mix Until The Concrete Is Deposited In Place At The Site Shall Not Exceed Forty Five (45) Minutes When The Concrete Is Hauled In Non-agitating Trucks, Nor Ninety (90) Minutes When Hauled In Truck Mixers Or Truck Agitators, Except That In Hot Weather Or Under Other Conditions Contributing To Quick Hardening Of The Concrete, The Maximum Allowable Time May Be Reduced By The Lgu Project Engineer. In Exceptional Cases And When Volumetric Measurements Are Authorized For Small Project Requiring Less Than 75 Cu.m. Of Concrete Per Day Of Pouring, The Weight Proportions Shall Be Converted To Equivalent Volumetric Proportions. In Such Cases, Suitable Allowance Shall Be Made For Variations In The Moisture Condition Of The Aggregates, Including The Bulking Effect In The Fine Aggregate. Batching And Mixing Shall Be In Accordance With Astm C 685, Section 6 Through 9. Concrete Mixing By Chute Is Allowed Provided That A Weighing Scale For Determining The Batch Weight Will Be Used. Retendering Concrete By Adding Water Or By Other Means Shall Not Be Permitted, Except That When Concrete Is Delivered In Truck Mixers, Additional Water May Be Added To The Batch Materials And Additional Mixing Performed To Increase The Slump To Meet The Specified Requirements, If Permitted By The Lgu Project Engineer, Provided All These Operations Are Performed Within Forty-five (45) Minutes After The Initial Mixing Operation And The Water-cement Ratio Is Not Exceeded. Concrete That Is Not Within The Specified Slump Limits At The Time Of Placement Shall Not Be Used. Admixtures For Increasing The Workability Or For Accelerating The Setting Of The Concrete Will Be Permitted Only When Specifically Approved By The Lgu Project Engineer. 311.3.8 Limitation Of Mixing No Concrete Shall Be Mixed, Placed Or Finished When Natural Light Is Insufficient, Unless An Adequate And Approved Artificial Lighting System Is Operated. During Hot Weather, The Lgu Project Engineer Shall Require That Steps Be Taken To Prevent The Temperature Of Mixed Concrete From Exceeding A Maximum Temperature Of (900f 320c). Concrete Not In Place Within Ninety (90) Minutes From The Time The Ingredients Were Charged Into The Mixing Drum Or That Has Developed Initial Set Shall Not Be Used. Retendering Of Concrete Or Mortar Which Has Partially Hardened, That Is Remixing With Or Without Additional Cement, Aggregate, Or Water, Shall Not Be Permitted. In Order That The Concrete May Be Properly Protected Against The Effects Of Rain Before The Concrete Is Sufficiently Hardened, The Contractor Will Be Required To Have Available At All Times Materials For The Protection Of The Edges And Surface Of The Unhardened Concrete. 311.3.9 Placing Concrete Concrete Shall Be Deposited In Such A Manner To Require Minimal Rehandling. Unless Truck Mixers Or Non-agitating Hauling Equipment Are Equipped With Means To Discharge Concrete Without Segregation Of The Materials, The Concrete Shall Be Unloaded Into An Approved Spreading Device And Mechanically Spread On The Grade In Such A Manner As To Prevent Segregation. Placing Shall Be Continuous Between Transverse Joints Without The Use Of Intermediate Bulkheads. Necessary Hand Spreading Shall Be Done With Shovels, Not Rakes. Workmen Shall Not Be Allowed To Walk In The Freshly Mixed Concrete With Boots Or Shoes Coated With Earth Or Foreign Substances. When Concrete Is To Be Placed Adjoining A Previously Constructed Lane And Mechanical Equipment Will Be Operated Upon The Existing Lane, That Previously Constructed Lane Shall Have Attained The Strength For Fourteen (14) Day Concrete. If Only Finishing Equipment Is Carried On The Existing Lane, Paving In Adjoining Lanes May Be Permitted After Three (3) Days. Concrete Shall Be Thoroughly Consolidated Against And Along The Faces Of All Forms And Along The Full Length And On Both Sides Of All Joint Assemblies, By Means Of Vibrators Inserted In The Concrete. Vibrators Shall Not Be Permitted To Come In Contact With A Joint Assembly, The Grade, Or A Side Form. In No Case Shall The Vibrator Be Operated Longer Than Fifteen (15) Seconds In Any One Location. Concrete Shall Be Deposited As Near As Possible To The Expansion And Contraction Joints Without Disturbing Them, But Shall Not Be Dumped From The Discharge Bucket Or Hopper Into A Joint Assembly Unless The Hopper Is Well Centered On The Joint Assembly. Should Any Concrete Material Fall On Or Be Worked Into The Surface Of A Complete Slab, It Shall Be Removed Immediately. 311.3.10 Test Specimens As Work Progresses, At Least One (1) Set Consisting Of Three (3) Concrete Beam Test Specimens, 150 Mm X 150 Mm X 525 Mm Or 900 Mm Shall Be Taken From Each 330 M2 Of Pavement, 230 Mm Depth, Or Fraction Thereof Placed Each Day. Test Specimens Shall Be Made Under The Supervision Of The Lgu Project Engineer, And The Contractor Shall Provide All Concrete And Other Facilities Necessary In Making The Test Specimens And Shall Protect Them From Damage By Construction Operations. Cylinder Samples Shall Not Be Used As Substitute For Determining The Adequacy Of The Strength Of Concrete. The Beams Shall Be Made, Cured, And Tested In Accordance With Aashto T 23 And T 97. 311.3.11 Strike-off Of Concrete And Placement Of Reinforcement Following The Placing Of The Concrete, It Shall Be Struck Off To Conform To The Cross-section Shown On The Plans And To An Elevation Such That When The Concrete Is Properly Consolidated And Finished, The Surface Of The Pavement Will Be At The Elevation Shown On The Plans. When Reinforced Concrete Pavement Is Placed In Two (2) Layers, The Bottom Layer Shall Be Struck Off And Consolidated To Such Length And Depth That The Sheet Of Fabric Or Bar Mat May Be Laid Full Length On The Concrete In Its Final Position Without Further Manipulation. The Reinforcement Shall Then Be Placed Directly Upon The Concrete, After Which The Top Layer Of The Concrete Shall Be Placed, Struck Off And Screened. Any Portion Of The Bottom Layer Of Concrete Which Has Been Placed More Than 30 Minutes Without Being Covered With The Top Layer Shall Be Removed And Replaced With Freshly Mixed Concrete At The Contractor’s Expense. When Reinforced Concrete Is Placed In One Layer, The Reinforcement May Be Firmly Positioned In Advance Of Concrete Placement Or It May Be Placed At The Depth Shown On The Plans In Plastic Concrete, After Spreading By Mechanical Or Vibratory Means. Reinforcing Steel Shall Be Free From Dirt, Oil, Paint, Grease, Mill Scale And Loose Or Thick Rust Which Could Impair Bond Of The Steel With The Concrete. 311.3.12 Joints Joints Shall Be Constructed Of The Type And Dimensions, And At The Locations Required By The Plans Or Special Provisions. All Joints Shall Be Protected From The Intrusion Of Injurious Foreign Material Until Sealed. 1. Longitudinal Joint Deformed Steel Tie Bars Of Specified Length, Size, Spacing And Materials Shall Be Placed Perpendicular To The Longitudinal Joints, They Shall Be Placed By Approved Mechanical Equipment Or Rigidly Secured By Chair Or Other Approved Supports To Prevent Displacement. Tie Bars Shall Not Be Painted Or Coated With Asphalt Or Other Materials Or Enclosed In Tubes Or Sleeves. When Shown On The Plans And When Adjacent Lanes Of Pavement Are Constructed Separately, Steel Side Forms Shall Be Used Which Will Form A Keyway Along The Construction Joint. Tie Bars, Except Those Made Of Rail Steel, May Be Bent At Right Angles Against The Form Of The First Lane Constructed And Straightened Into Final Position Before The Concrete Of The Adjacent Lane Is Placed, Or In Lieu Of Bent Tie Bars, Approved Two-piece Connectors May Be Used. Longitudinal Formed Joints Shall Consist Of A Groove Or Cleft, Extending Downward From And Normal To, The Surface Of The Pavement. These Joints Shall Be Effected Or Formed By An Approved Mechanically Or Manually Operated Device To The Dimensions And Line Indicated On The Plans And While The Concrete Is In A Plastic State. The Groove Or Cleft Shall Be Filled With Either A Premolded Strip Or Poured Material As Required. The Longitudinal Joints Shall Be Continuous, There Shall Be No Gaps In Either Transverse Or Longitudinal Joints At The Intersection Of The Joints. Longitudinal Sawed Joints Shall Be Cut By Means Of Approved Concrete Saws To The Depth, Width And Line Shown On The Plans. Suitable Guide Lines Or Devices Shall Be Used To Assure Cutting The Longitudinal Joint On The True Line. The Longitudinal Joint Shall Be Sawed Before The End Of The Curing Period Or Shortly Thereafter And Before Any Equipment Or Vehicles Are Allowed On The Pavement. The Sawed Area Shall Be Thoroughly Cleaned And, If Required, The Joint Shall Immediately Be Filled With Sealer. Longitudinal Pavement Insert Type Joints Shall Be Formed By Placing A Continuous Strip Of Plastic Materials Which Will Not React Adversely With The Chemical Constituent Of The Concrete. 2. Transverse Expansion Joint The Expansion Joint Filler Shall Be Continuous From Form To Form, Shaped To Sub-grade And To The Keyway Along The Form. Preformed Joint Filler Shall Be Furnished In Lengths Equal To The Pavement Width Or Equal To The Width Of One Lane. Damaged Or Repaired Joint Filler Shall Not Be Used. The Expansion Joint Filler Shall Be Held In A Vertical Position. An Approved Installing Bar, Or Other Device, Shall Be Used If Required To Secure Preformed Expansion Joint Filler At The Proper Grade And Alignment During Placing And Finishing Of The Concrete. Finished Joint Shall Not Deviate More Than 6 Mm From A Straight Line. If Joint Fillers Are Assembled In Sections, There Shall Be No Offsets Between Adjacent Units. No Plugs Of Concrete Shall Be Permitted Anywhere Within The Expansion Space. 3. Transverse Contraction Joint/weakened Joint When Shown On The Plans, It Shall Consist Of Planes Of Weakness Created By Forming Or Cutting Grooves In The Surface Of The Pavement And Shall Include Load Transfer Assemblies. The Depth Of The Weakened Plane Joint Should At All Times Not Be Less Than 50 Mm, While The Width Should Not Be More Than 6 Mm. A. Transverse Strip Contraction Joint. It Shall Be Formed By Installing A Parting Strip To Be Left In Place As Shown On The Plans. B. Formed Groove. It Shall Be Made By Depressing An Approved Tool Or Device Into The Plastic Concrete. The Tool Or Device Shall Remain In Place At Least Until The Concrete Has Attained Its Initial Set And Shall Then Be Removed Without Disturbing The Adjacent Concrete, Unless The Device Is Designed To Remain In The Joint. C. Sawed Contraction Joint. It Shall Be Created By Sawing Grooves In The Surface Of The Pavement Of The Width Not More Than 6 Mm, Depth Should At All Times Not Be Less Than 50 Mm, And At The Spacing And Lines Shown On The Plans, With An Approved Concrete Saw. After Each Joint Is Sawed, It Shall Be Thoroughly Cleaned Including The Adjacent Concrete Surface. Sawing Of The Joint Shall Commence As Soon As The Concrete Has Hardened Sufficiently To Permit Sawing Without Excessive Raveling, Usually 4 To 24 Hours. All Joints Shall Be Sawed Before Uncontrolled Shrinkage Cracking Takes Place. If Necessary, The Sawing Operations Shall Be Carried On During The Day Or Night, Regardless Of Weather Conditions. The Sawing Of Any Joint Shall Be Omitted If Crack Occurs At Or Near The Joint Location Prior To The Time Of Sawing. Sawing Shall Be Discounted When A Crack Develops Ahead Of The Saw. In General, All Joints Should Be Sawed In Sequence. If Extreme Condition Exist Which Make It Impractical To Prevent Erratic Cracking By Early Sawing, The Contraction Joint Groove Shall Be Formed Prior To Initial Set Of Concrete As Provided Above. 4. Transverse Construction Joint It Shall Be Constructed When There Is An Interruption Of More Than 30 Minutes In The Concreting Operations. No Transverse Joint Shall Be Constructed Within 1.50 M Of An Expansion Joint, Contraction Joint, Or Plane Of Weakness. If Sufficient Concrete Has Been Mixed At The Time Of Interruption To Form A Slab Of At Least 1.5 M Long, The Excess Concrete From The Last Preceding Joint Shall Be Removed And Disposed Off As Directed. 5. Load Transfer Device Dowel, When Used, Shall Be Held In Position Parallel To The Surface And Center Line Of The Slab By A Metal Device That Is Left In The Pavement. The Portion Of Each Dowel Painted With One Coat Of Lead Or Tar, In Conformance With The Requirements Of Item 404, Reinforcing Steel, Shall Be Thoroughly Coated With Approved Bituminous Materials, E.g., Mc-70, Or An Approved Lubricant, To Prevent The Concrete From Binding To That Portion Of The Dowel. The Sleeves For Dowels Shall Be Metal Designed To Cover 50 Mm Plus Or Minus 5 Mm (1/4 Inch), Of The Dowel, With A Watertight Closed End And With A Suitable Stop To Hold The End Of The Sleeves At Least 25 Mm (1 Inch) From The End Of The Dowel. In Lieu Of Using Dowel Assemblies At Contraction Joints, Dowel May Be Placed In The Full Thickness Of Pavement By A Mechanical Device Approved By The Lgu Project Engineer. 311.3.13 Final Strike-off (consolidation And Finishing) 1. Sequence The Sequence Of Operations Shall Be The Strike-off And Consolidation, Floating And Removal Of Laitance, Straight-edging And Final Surface Finish. Work Bridges Or Other Devices Necessary To Provide Access To The Pavement Surface For The Purpose Of Finishing Straight-edging, And Make Corrections As Hereinafter Specified, Shall Be Provided By The Contractor. In General, The Addition Of Water To The Surface Of The Concrete To Assist In Finishing Operations Will Not Be Permitted. If The Application Of Water To The Surface Is Permitted, It Shall Be Applied As Fog Spray By Means Of An Approve Spray Equipment. 2. Finishing Joints The Concrete Adjacent To Joints Shall Be Compacted Or Firmly Placed Without Voids Or Segregation Against The Joint Material Assembly, Also Under And Around All Load Transfer Devices, Joint Assembly Units, And Other Features Designed To Extend Into The Pavement. Concrete Adjacent To Joints Shall Be Mechanically Vibrated As Required In Subsection 311.3.9, Placing Concrete. After The Concrete Has Been Placed And Vibrated Adjacent To The Joints As Required In Subsection 311.3.9, The Finishing Machine Shall Be Brought Forward, Operating In A Manner To Avoid Damage Or Misalignment Of Joints. If Uninterrupted Operation Of The Finishing Machine, To Over And Beyond The Joints Causes Segregation Of Concrete, Damage To, Or Misalignment Of The Joints, The Finishing Machine Shall Be Stopped When The Front Screed Is Approximately 20 Cm (8 Inches) From The Joint. Segregated Concrete Shall Be Removed From In Front Of And Off The Joint. The Front Screed Shall Be Lifted And Set Directly On Top Of The Joint And The Forward Motion Of The Finishing Machine Resumed. When The Second Screed Is Close Enough To Permit The Excess Mortar In Front Of It To Flow Over The Joint, It Shall Be Lifted And Carried Over The Joint. Thereafter, The Finishing Machine May Be Run Over The Joint Without Lifting The Screeds, Provided There Is No Segregated Concrete Immediately Between The Joint And The Screed Or On Top Of The Joint. 3. Machine Finishing A. Non-vibratory Method. The Concrete Shall Be Distributed Or Spread As Soon As Placed. As Soon As The Concrete Has Been Placed, It Shall Be Struck Off And Screwed By An Approved Finishing Machine. The Machine Shall Go Over Each Area Of Pavement As Many Times And At Such Intervals As Necessary To Give The Proper Compaction And Leave A Surface Of Uniform Texture. Excessive Operation Over A Given Area Shall Be Avoided. The Tops Of The Forms Shall Be Kept Clean By An Effective Device Attached To The Machine And The Travel Of The Machine On The Forms Shall Be Maintained True Without Wobbling Or Other Variation Tending To Affect The Precision Finish. During The First Pass Of The Finishing Machine, A Uniform Ridge Of Concrete Shall Be Maintained Ahead Of The Front Screed In Its Entire Length. B. Vibratory Method. When Vibration Is Specified, Vibrators For Full Width Vibration Of Concrete Paving Slabs, Shall Meet The Requirements In Subsection 311.3.2, Equipment. If Uniform And Satisfactory Density Of The Concrete Is Not Obtained By The Vibratory Method At Joints, Along Forms, At Structures, And Throughout The Pavement, The Contractor Will Be Required To Furnish Equipment And Method Which Will Produce Pavement Conforming To The Specifications. All Provisions In Item (a) Above Not In Conflict With The Provisions For The Vibratory Method Shall Govern. 4. Hand Finishing Hand Finishing Methods May Only Be Used Under The Following Conditions: A. In The Event Of Breakdown Of The Mechanical Equipment, Hand Methods May Be Used To Finish The Concrete Already Deposited On The Grade. B. In Narrow Widths Or Areas Of Irregular Dimensions Where Operations Of The Mechanical Equipment Is Impractical, Hand Methods May Be Used. Concrete, As Soon As Placed, Shall Be Struck Off And Screeded. An Approved Portable Screed Shall Be Used. A Second Screed Shall Be Provided For Striking Off The Bottom Layer Of Concrete If Reinforcement Is Used. The Screed For The Surface Shall Be At Least 60 Cm (2 Feet) Longer Than The Maximum Width Of The Slab To Be Struck Off. It Shall Be Of Approved Design, Sufficiently Rigid To Retain Its Shape, And Constructed Either Of Metal Or Other Suitable Material Shod With Metal. Consolidation Shall Be Attained By The Use Of Suitable Vibrator Or Other Approved Equipment. In Operation, The Screed Shall Be Moved Forward On The Forms With A Combined Longitudinal And Transverse Shearing Motion, Moving Always In The Direction In Which The Work Is Progressing And So Manipulated That Neither End Is Raised From The Side Forms During The Striking Off Process. If Necessary, This Shall Be Repeated Until The Surface Is Of Uniform Texture, True To Grade And Cross-section, And Free From Porous Areas. 5. Floating After The Concrete Has Been Struck Off And Consolidated, It Shall Be Further Smoothed, Trued, And Consolidated By Means Of A Longitudinal Float, Either By Hand Or Mechanical Method. A. Hand Method. The Hand-operated Longitudinal Float Shall Be Not Less Than 365 Cm (12 Feet) In Length And 15 Cm (6 Inches) In Width, Properly Stiffened To Prevent Flexibility And Warping. The Longitudinal Float, Operated From Foot Bridges Resting On The Side Forms And Spanning But Not Touching The Concrete, Shall Be Worked With A Sawing Motion While Held In A Floating Position Parallel To The Road Center Line, And Moving Gradually From One Side Of The Pavement To The Other. Movement Ahead Along The Center Line Of The Pavement Shall Be In Successive Advances Of Not More Than One-half The Length Of The Float. Any Excess Water Or Soupy Material Shall Be Wasted Over The Side Forms On Each Pass. B. Mechanical Method. The Mechanical Longitudinal Float Shall Be Of A Design Approved By The Lgu Project Engineer, And Shall Be In Good Working Condition. The Tracks From Which The Float Operates Shall Be Accurately Adjusted To The Required Crown. The Float Shall Be Accurately Adjusted And Coordinated With The Adjustment Of The Transverse Finishing Machine So That A Small Amount Of Mortar Is Carried Ahead Of The Float At All Times. The Forward Screed Shall Be Adjusted So That The Float Will Lap The Distance Specified By The Lgu Project Engineer On Each Transverse Trip. The Float Shall Pass Over Each Areas Of Pavement At Least Two Times, But Excessive Operation Over A Given Area Will Not Be Permitted. Any Excess Water Or Soupy Material Shall Be Wasted Over The Side Forms On Each Pass. C. Alternative Mechanical Method. As An Alternative, The Contractor May Use A Machine Composed Of A Cutting And Smoothing Float Or Floats Suspended From And Guided By A Rigid Frame. The Frame Shall Be Carried By Four Or More Visible Wheels Riding On, And Constantly In Contact With The Side Forms. If Necessary, Following One Of The Preceding Method Of Floating, Long Handled Floats Having Blades Not Less Than 150 Cm (5 Feet) In Length And 15 Cm (6 Inches) In Width May Be Used To Smooth And Fill In Open-textured Areas In The Pavement. Long-handled Floats Shall Not Be Used To Float The Entire Surface Of The Pavement In Lieu Of, Or Supplementing, One Of The Preceding Methods Of Floating. When Strike Off And Consolidation Are Done By The Hand Method And The Crown Of The Pavement Will Not Permit The Use Of The Longitudinal Float, The Surface Shall Be Floated Transversely By Means Of The Long-handled Float. Care Shall Be Taken Not To Work The Crown Out Of The Pavement During The Operation. After Floating, Any Excess Water And Laitance Shall Be Removed From The Surface Of The Pavement By A 3-m Straight-edge Or More In Length. Successive Drags Shall Be Lapped One-half The Length Of The Blade. 6. Straight-edge Testing And Surface Correction After The Floating Has Been Completed And The Excess Water Removed, But While The Concrete Is Still Plastic, The Surface Of The Concrete Shall Be Tested For Trueness With A 300 Cm Long Straight-edge. For This Purpose, The Contractor Shall Furnish And Use An Accurate 300-cm Straight-edge Swung From Handles 100 Cm (3 Feet) Longer Than One-half The Width Of The Slab. The Straight-edge Shall Be Held In Contact With The Surface In Successive Positions Parallel To The Road Center Line And The Whole Area Gone Over From One Side Of The Slab To The Other As Necessary. Advances Along The Road Shall Be In Successive Stages Of Not More Than One-half The Length Of The Straight-edge. Any Depressions Found Shall Be Immediately Filled With Freshly Mixed Concrete, Struck Off, Consolidated And Refinished. High Areas Shall Be Cut Down And Refinished. Special Attention Shall Be Given To Assure That The Surface Across Joints Meets The Requirements For Smoothness. Straight-edge Testing And Surface Corrections Shall Continue Until The Entire Surface Is Found To Be Free From Observable Departures From The Straight-edge And The Slab Conforms To The Required Grade And Cross-section. 7. Final Finish If The Surface Texture Is Broom Finished, It Shall Applied When The Water Sheen Has Practically Disappeared. The Broom Shall Be Drawn From The Center To The Edge Of The Pavement With Adjacent Strokes Slightly Overlapping. The Brooming Operation Should Be So Executed That The Corrugations Produced In The Surface Shall Be Uniform In Appearance And Not More Than 1.5 Mm In Depth. Brooming Shall Be Completed Before The Concrete Is In Such Condition That The Surface Will Be Unduly Roughened By The Operation. The Surface Thus Finished Shall Be Free From Rough And Porous Areas, Irregularities, And Depressions Resulting From Improper Handling Of The Broom. Brooms Shall Be Of The Quality Size And Construction And Be Operated So As To Produce A Surface Finish Meeting The Approval Of The Lgu Project Engineer. Subject To Satisfactory Results Being Obtained And Approval Of The Lgu Project Engineer, The Contractor Will Be Permitted To Substitute Mechanical Brooming In Lieu Of The Manual Brooming Herein Described. If The Surface Texture Is Belt Finished, When Straight-edging Is Complete And Water Sheen Has Practically Disappeared And Just Before The Concrete Becomes Non-plastic, The Surface Shall Be Belted With 2-ply Canvass Belt Not Less Than 20 Cm Wide And At Least 100 Cm Longer Than The Pavement Width. Hand Belts Shall Have Suitable Handles To Permit Controlled, Uniform Manipulation. The Belt Shall Be Operated With Short Strokes Transverse To The Center Line And With A Rapid Advances Parallel To The Center Line. If The Surface Texture Is Drag Finished, A Drag Shall Be Used Which Consists Of A Seamless Strip Of Damp Burlap Or Cotton Fabric, Which Shall Produce A Uniform Of Gritty Texture After Dragging It Longitudinally Along The Full Width Of Pavement. For Pavement 5 M Or More In Width, The Drag Shall Be Mounted On A Bridge Which Travels On The Forms. The Dimensions Of The Drag Shall Be Such That A Strip Of Burlap Or Fabric At Least 100 Cm Wide Is In Contact With The Full Width Of Pavement Surface While The Drag Is Used. The Drag Shall Consist Of Not Less Than 2 Layers Of Burlap With The Bottom Layer Approximately 15 Cm Wider Than The Layer. The Drag Shall Be Maintained In Such Condition That The Resultant Surface Is Of Uniform Appearance And Reasonably Free From Grooves Over 1.5 Mm In Depth. Drag Shall Be Maintained Clean And Free From Encrusted Mortar. Drags That Cannot Be Cleaned Shall Be Discarded And New Drags Be Substituted. Regardless Of The Method Used For Final Finish, The Hardened Surface Of Pavement Shall Have A Coefficient Of Friction Of 0.25 Or More. Completed Pavement That Is Found To Have A Coefficient Of Friction Less Than 0.25 Shall Be Grounded Or Scored By The Contractor At His Expense To Provide The Required Coefficient Of Friction. 8. Edging At Forms And Joints After The Final Finish, But Before The Concrete Has Taken Its Initial Set, The Edges Of The Pavement Along Each Side Of Each Slab, And On Each Side Of Transverse Expansion Joints, Formed Joints, Transverse Construction Joints, And Emergency Construction Joints, Shall Be Worked With An Approved Tool And Rounded To The Radius Required By The Plans. A Well – Defined And Continuous Radius Shall Be Produced And A Smooth, Dense Mortar Finish Obtained. The Surface Of The Slab Shall Not Be Unduly Disturbed By Tilting The Tool During The Use. At All Joints, Any Tool Marks Appearing On The Slab Adjacent To The Joints Shall Be Eliminated By Brooming The Surface. In Doing This, The Rounding Of The Corner Of The Slab Shall Not Be Disturbed. All Concrete On Top Of The Joint Filler Shall Be Completely Removed. All Joints Shall Be Tested With A Straight-edge Before The Concrete Has Set And Correction Made If One Edge Of The Joint Is Higher Than The Other. 311.3.14 Surface Test As Soon As The Concrete Has Hardened Sufficiently, The Pavement Surface Shall Be Tested With A 3-m Straight-edge Or Other Specified Device. Areas Showing High Spots Of More Than 3 Mm But Not Exceeding 12 Mm In 3 M Shall Be Marked And Immediately Ground Down With An Approved Grinding Tool To An Elevation Where The Area Or Spot Will Not Show Surface Deviations In Excess Of 3 Mm When Tested With 3 M Straight-edge. Where The Departure From Correct Cross-section Exceeds 12 Mm, The Pavement Shall Be Removed And Replaced By And At The Expense Of The Contractor. Any Area Or Section So Removed Shall Be Not Less Than 1.5 M In Length And Not Less Than The Full Width Of The Lane Involved. When It Is Necessary To Remove And Replace A Section Of Pavement, Any Remaining Portion Of The Slab Adjacent To The Joints That Is Less Than 1.5 M In Length, Shall Also Be Removed And Replaced. 311.3.15 Curing Immediately After The Finishing Operations Have Been Completed And The Concrete Has Sufficiently Set, The Entire Surface Of The Newly Placed Concrete Shall Be Cured In Accordance With Either One Of The Methods Described Herein. Failure To Provide Sufficient Cover Material Of Whatever Kind The Contractor May Elect To Use, Or The Lack Of Water To Adequately Take Care Of Both Curing And Other Requirements, Shall Be A Cause For Immediate Suspension Of Concreting Operations. The Concrete Shall Not Be Left Exposed For More Than ½ Hour Between Stages Of Curing Or During The Curing Period. In All Congested Places, Concrete Works Should Be Designed So That The Designed Strength Is Attained. 1. Cotton Of Burlap Mats The Surface Of The Pavement Shall Be Entirely Covered With Mats. The Mats Used Shall Be Of Such Length (or Width) That As Laid They Will Extend At Least Twice The Thickness Of The Pavement Beyond The Edges Of The Slab. The Mat Shall Be Placed So That The Entire Surface And The Edges Of The Slab Are Completely Covered. Prior To Being Placed, The Mats Shall Be Saturated Thoroughly With Water. The Mat Shall Be So Placed And Weighted Down So As To Cause Them To Remain In Intimate Contact With The Covered Surface. The Mat Shall Be Maintained Fully Wetted And In Position For 72 Hours After The Concrete Has Been Placed Unless Otherwise Specified. 2. Waterproof Paper The Top Surface And Sides Of The Pavement Shall Be Entirely Covered With Waterproof Paper, The Units Shall Be Lapped At Least 45 Cm. The Paper Shall Be So Placed And Weighted Down So As To Cause It To Remain In Intimate Contact With The Surface Covered. The Paper Shall Have Such Dimension But Each Unit As Laid Will Extend Beyond The Edges Of The Slab At Least Twice The Thickness Of The Pavement, Or At Pavement Width And 60 Cm Strips Of Paper For The Edges. If Laid Longitudinally, Paper Not Manufactured In Sizes Which Will Provide This Width Shall Be Securely Sewed Or Cemented Together, The Joints Being Securely Sealed In Such A Manner That They Do Not Open Up Or Separate During The Curing Period. Unless Otherwise Specified, The Covering Shall Be Maintained In Place For 72 Hours After The Concrete Has Been Placed. The Surface Of The Pavement Shall Be Thoroughly Wetted Prior To The Placing Of The Paper. 3. Straw Curing When This Type Of Curing Is Used, The Pavement Shall Be Cured Initially With Burlap Or Cotton Mats, Until After Final Set Of The Concrete Or, In Any Case, For 12 Hours After Placing The Concrete. As Soon As The Mats Are Removed, The Surface And Sides Of The Pavement Shall Be Thoroughly Wetted And Covered With At Least 20 Cm Of Straw Or Hay, Thickness Of Which Is To Be Measured After Wetting. If The Straw Or Hay Covering Becomes Displaced During The Curing Period, It Shall Be Replaced To The Original Depth And Saturated. It Shall Be Kept Thoroughly Saturated With Water For 72 Hours And Thoroughly Wetted Down During The Morning Of The Fourth Day, And The Cover Shall Remain In Place Until The Concrete Has Attained The Required Strength. 4. Impervious Membrane Method The Entire Surface Of The Pavement Shall Be Sprayed Uniformly With White Pigmented Curing Compound Immediately After The Finishing Of The Surface And Before The Set Of The Concrete Has Taken Place, Or If The Pavement Is Cured Initially With Jute Or Cotton Mats, It May Be Applied Upon Removal Of The Mass. The Curing Compound Shall Not Be Applied During Rain. Curing Compound Shall Be Applied Under Pressure At The Rate 4 L To Not More Than 14 M2 By Mechanical Sprayers. The Spraying Equipment Shall Be Equipped With A Wind Guard. At The Time Of Use, The Compound Shall Be In A Thoroughly Mixed Condition With The Pigment Uniformly Dispersed Throughout The Vehicle. During Application, The Compound Shall Be Stirred Continuously By Effective Mechanical Means. Hand Spraying Of Odd Widths Or Shapes And Concrete Surface Exposed By The Removal Of Forms Will Be Permitted. Curing Compound Shall Not Be Applied To The Inside Faces Of Joints To Be Sealed, But Approved Means Shall Be Used To Insure Proper Curing At Least 72 Hours And To Prevent The Intrusion Of Foreign Material Into The Joint Before Sealing Has Been Completed. The Curing Compound Shall Be Of Such Character That The Film Will Harden Within 30 Minutes After Application. Should The Film Be Damaged From Any Cause Within The 72 Hour Curing Period, The Damaged Portions Shall Be Repaired Immediately With Additional Compound. 5. White Polyethylene Sheet The Top Surface And Sides Of The Pavement Shall Be Entirely Covered With Polyethylene Sheeting. The Units Used Shall Be Lapped At Least 45 Cm. The Sheeting Shall Be So Placed And Weighted Down So As To Cause It To Remain Intimate Contact With The Surface Covered. The Sheeting As Prepared For Use Shall Have Such Dimension That Each Unit As Laid Will Extend Beyond The Edges Of The Slab At Least Twice The Thickness Of The Pavement. Unless Otherwise Specified, The Covering Shall Be Maintained In Place For 72 Hours After The Concrete Has Been Placed. 311.3.16 Removal Of Forms After Forms For Concrete Shall Remain In Place Undisturbed For Not Less Than Twenty Four (24) Hours After Concrete Pouring. In The Removal Of Forms, Crowbars Should Be Used In Pulling Out Nails And Pins. Care Should Be Taken So As Not To Break The Edges Of The Pavement. In Case Portions Of The Concrete Are Spalled, They Shall Be Immediately Repaired With Fresh Mortar Mixed In The Proportion Of One Part Of Portland Cement And Two Parts Fine Aggregates. Major Honeycomb Areas Will Be Considered As Defective Work And Shall Be Removed And Replaced At The Expense Of The Contractor. Any Area Or Section So Removed Shall Not Be Less Than The Distance Between Weakened Plane Joint Nor Less Than The Full Width Of The Lane Involved. 311.3.17 Sealing Joints Joints Shall Be Sealed With Asphalt Sealant Soon After Completion Of The Curing Period And Before The Pavement Is Opened To Traffic, Including The Contractor’s Equipment. Just Prior To Sealing, Each Joint Shall Be Thoroughly Cleaned Of All Foreign Materials Including Membrane Curing Compound And The Joint Faces Shall Be Clean And Surface Dry When The Seal Is Applied. The Sealing Material Shall Be Applied To Each Joint Opening To Conform To The Details Shown On The Plans Or As Directed By The Lgu Project Engineer. Material For Seal Applied Hot Shall Be Stirred During Heating So That Localized Overheating Does Not Occur. The Pouring Shall Be Done In Such A Manner That The Material Will Not Be Spilled On The Exposed Surfaces Of The Concrete. The Use Of Sand Or Similar Material As A Cover For The Seal Will Not Be Permitted. Preformed Elastomeric Gaskets For Sealing Joints Shall Be Of The Cross-sectional Dimensions Shown On The Plans. Seals Shall Be Installed By Suitable Tools, Without Elongation And Secured In Placed With An Approved Lubricant Adhesive Which Shall Cover Both Sides Of The Concrete Joints. The Seals Shall Be Installed In A Compressive Condition And Shall At Time Of Placement Be Below The Level Of The Pavement Surface By Approximately 6 Mm. The Seals Shall Be In One Piece For The Full Width Of Each Transverse Joint. 311.3.18 Protection Of Pavement The Contractor Shall Protect The Pavement And Its Appurtenances Against Both Public Traffic And Traffic Caused By His Own Employees And Agents. This Shall Include Watchmen To Direct Traffic And The Erection Of And Maintenance Of Warning Signs, Lights, Pavement Bridges Or Cross-overs, Etc. The Plans Or Special Provisions Will Indicate The Location And Type Of Device Or Facility Required To Protect The Work And Provide Adequately For Traffic. All Boreholes After Thickness And/or Strength Determinations Of Newly Constructed Asphalt And Concrete Pavements Shall Be Immediately Filled/restored With The Prescribed Concrete/asphalt Mix After Completion Of The Drilling Works. Any Damage To The Pavement, Occurring Prior To Final Acceptance, Shall Be Repaired Or The Pavement Be Replaced. 311.3.19 Concrete Pavement – Slip Form Method If The Contract Calls For The Construction Of Pavement Without The Use Of Fixed Forms, The Following Provisions Shall Apply: 1. Grade After The Grade Or Base Has Been Placed And Compacted To The Required Density, The Areas Which Will Support The Paving Machine Shall Be Cut To The Proper Elevation By Means Of A Properly Designed Machine. The Grade On Which The Pavement Is To Be Constructed Shall Then Be Brought To The Proper Profile By Means Of Properly Designed Machine. If The Density Of The Base Is Disturbed By The Grading Operation, It Shall Be Corrected By Additional Compaction Before Concrete Is Placed. The Grade Should Be Constructed Sufficiently In Advance Of The Placing Of The Concrete. If Any Traffic Is Allowed To Use The Prepared Grade, The Grade Shall Be Checked And Corrected Immediately Before The Placing Of Concrete. 2. Placing Concrete The Concrete Shall Be Placed With An Approved Slip-form Paver Designed To Spread, Consolidate, Screed And Float-finish The Freshly Placed Concrete In One Complete Pass Of The Machine In Such A Manner That A Minimum Of Hand Finish Will Be Necessary To Provide A Dense And Homogenous Pavement In Conformance With The Plans And Specifications. The Machine Shall Vibrate The Concrete For The Full Width And Depth Of The Strip Of Pavement Being Placed. Such Vibration Shall Be Accompanied With Vibrating Tubes Or Arms Working In The Concrete Or With A Vibrating Screed Or Pan Operating On The Surface Of The Concrete. The Sliding Forms Shall Be Rigidly Held Together Laterally To Prevent Spreading Of The Forms. The Forms Shall Trail Behind The Paver For Such A Distance That No Appreciable Slumping Of The Concrete Will Occur, And That Necessary Final Finishing Can Be Accomplished While The Concrete Is Still Within The Forms. Any Edge Slump Of The Pavement, Exclusive Of Edge Rounding, In Excess Of 6 Mm Shall Be Corrected Before The Concrete Has Hardened. The Concrete Shall Be Held At A Uniform Consistency, Having A Slump Of Not More Than 40 Mm (1-12/ Inches). The Slip Form Paver Shall Be Operated With As Nearly As Possible A Continuous Forward Movement And That All Operations Of Mixing, Delivering And Spreading Concrete Shall Be Coordinated So As To Provide Uniform Progress With Stopping And Starting Of The Paver Held To A Minimum. If, For Any Reason, It Is Necessary To Stop The Forward Movement Of The Paver The Vibratory And Tamping Elements Shall Also Be Stopped Immediately. No Tractive Force Shall Be Applied To The Machine, Except That Which Is Controlled From The Machine. 3. Finishing The Surface Smoothness And Texture Shall Meet The Requirements Of Subsections 311.3.13 And 311.3.14. 4. Curing Unless Otherwise Specified, Curing Shall Be Done In Accordance With One Of The Methods Included In Subsection 311.3.15. The Curing Media Shall Be Applied At The Appropriate Time And Shall Be Applied Uniformly And Completely To All Surfaces And Edges Of The Pavement. 5. Joints All Joints Shall Be Constructed In Accordance With Subsection 311.3.12. 6. Protection Against Rain In Order That The Concrete May Be Properly Protected Against Rain Before The Concrete Is Sufficiently Hardened, The Contractor Will Be Required To Have Available At All Times, Materials For The Protection Of The Edges And Surface Of The Unhardened Concrete. Such Protective Materials Shall Consist Of Standard Metal Forms Or Wood Planks Having A Nominal Thickness Of Not Less Than 50 Mm (2 Inches) And A Nominal Width Of Not Less Than The Thickness Of The Pavement At Its Edge For The Protection Of The Pavement Edges, And Covering Material Such As Burlap Or Cotton Mats, Curing Paper Or Plastic Sheeting Materials For The Protection Of The Surface Of The Pavement. When Rain Appears Imminent, All Paving Operations Shall Stop And All Available Personnel Shall Begin Placing Forms Against The Sides Of The Pavement And Covering The Surface Of The Unhardened Concrete With The Protective Covering. 311.3.22 Acceptance Of Concrete The Strength Level Of The Concrete Will Be Considered Satisfactory If The Averages Of All Sets Of Three (3) Consecutive Strength Test Results Equal Or Exceed The Specified Strength, Fc’ And No Individual Strength Test Result Is Deficient By More Than 15% Of The Specified Strength, Fc’. Concrete Deemed To Be Not Acceptable Using The Above Criteria May Be Rejected Unless The Contractor Can Provide Evidence, By Means Of Core Tests, That The Quality Of Concrete Represented By Failed Test Results Is Acceptable In Place. At Least Three (3) Representative Cores Shall Be Taken From Each Member Or Area Of Concrete In Place That Is Considered Deficient. The Location Of Cores Shall Be Determined By The Engineer So That There Will Be At Least Impairment Of Strength Of The Structure. The Obtaining And Testing Of Drilled Cores Shall Be In Accordance With Aashto T 24. Concrete In The Area Represented By The Cores Will Be Considered Adequate If The Average Strength Of The Cores Is Equal To At Least 85% Of, And If No Single Core Is Less Than 75% Of, The Specified Strength, Fc’. If The Strength Of Control Specimens Does Not Meet The Requirements Of This Subsection, And It Is Not Feasible Or Not Advisable To Obtain Cores From The Structure Due To Structural Considerations, Payment Of The Concrete Will Be Made At An Adjusted Price Due To Strength Deficiency Of Concrete Specimens As Specified Hereunder: Deficiency In Strength Of Concrete Specimens, Percent (%) Percent (%) Of Contract Price Allowed Less Than 5 100 5 To Less Than 10 80 10 To Less Than 15 70 15 To Less Than 20 60 20 To Less Than 25 50 25 Or More 0 311.3.23 Opening To Traffic The Engineer Will Decide When The Pavement May Be Opened To Traffic. The Road Will Not Be Opened To Traffic Until Test Specimens Molded And Cured In Accordance With Aashto T 23 Have Attained The Minimum Strength Requirements In Subsection 311.2.11. If Such Tests Are Not Conducted Prior To The Specified Age The Pavement Shall Not Be Operated To Traffic Until 14 Days After The Concrete Was Placed. Before Opening To Traffic, The Pavement Shall Be Cleaned And Joint Sealing Completed. 311.3.24 Tolerance And Pavement Thickness 1. General The Thickness Of The Pavement Will Be Determined By Measurement Of Cores From The Completed Pavement In Accordance With Aashto T 148. The Completed Pavement Shall Be Accepted On A Lot Basis. A Lot Shall Be Considered As 1000 Linear Meters Of Pavement When A Single Traffic Lane Is Poured Or 500 Linear Meters When Two Lanes Are Poured Concurrently. The Last Unit In Each Slab Constitutes A Lot In Itself When Its Length Is At Least ½ Of The Normal Lot Length. If The Length Of The Last Unit Is Shorter Than ½ Of The Normal Lot Length, It Shall Be Included In The Previous Lot. Other Areas Such As Intersections, Entrances, Crossovers, Ramp, Etc., Will Be Grouped Together To Form A Lot. Small Irregular Areas May Be Included With Other Unit Areas To Form A Lot. Each Lot Will Be Divided Into Five (5) Equal Segments And One Core Will Be Obtained From Each Segment In Accordance With Aashto T 24. 2. Pavement Thickness It Is The Intent Of This Specification That The Pavement Has A Uniform Thickness As Called For On The Plans For The Average Of Each Lot As Defined. After The Pavement Has Met All Surface Smoothness Requirements, Cores For Thickness Measurements Will Be Taken. In Calculating The Average Thickness Of The Pavement, Individual Measurements Which Are In Excess Of The Specified Thickness By More Than 5 Mm Will Be Considered As The Specified Thickness Plus 5 Mm And Measurement Which Are Less Than The Specified Thickness By More Than 25 Mm Shall Not Be Included In The Average. When The Average Thickness For The Lot Is Deficient, The Contract Unit Price Will Be Adjusted For Thickness In Accordance With Paragraph (3 Below). Individual Areas Within A Segment Found Deficient In Thickness By More Than 25 Mm Shall Be Evaluated By The Lgu Project Engineer, And If In His Judgment, The Deficient Areas Warrant Removal, They Shall Be Removed And Replaced By The Contractor With Pavement Of The Specified Thickness At His Entire Expense. However, If The Evaluation Of The Lgu Project Engineer Is That The Deficient Area Should Not Be Removed And Replaced, Such Area Will Not Be Paid. When The Measurement Of Any Core Is Less Than The Specified Thickness By More Than 25 Mm, The Actual Thickness Of The Pavement In This Area Will Be Determined By Taking Additional Cores At No Less Than 5 M Intervals Parallel To The Center Line In Each Direction From The Affected Location Until A Core Is Found In Each Direction, Which Is Not Deficient In Thickness By More Than 25 Mm. The Area Of Slab For Which No Payment Will Be Made Shall Be The Product Of The Paving Width Multiplied By The Distance Along The Center Line Of The Road Between Transverse Sections Found Not Deficient In Thickness By More Than 25 Mm. The Thickness Of The Remainder Of The Segment To Be Used To Get The Average Thickness Of Each Lot Shall Be Determined By Taking The Average Thickness Of Additional Cores Which Are Not Deficient By More Than 25 Mm. 3. Adjustment For Thickness When The Average Thickness Of The Pavement Per Lot Is Deficient, Payment For The Lot Shall Be Adjusted As Follows: Deficiency In The Average Thickness Per Lot (mm) Percent (%) Of Contract Price Per Lot 0 – 5 100% Payment 6 – 10 95% Payment 11 – 15 85% Payment 16 – 20 70% Payment 21 – 25 50% Payment More Than 25 Remove And Replace/ No Payment No Acceptance And Final Payment Shall Be Made On Completed Pavement Unless Core Test For Thickness Determination Is Conducted 311.4 Environmental Measures In Loading Cement To The Truck And Unloading It To The Temporary Bodega, And From The Bodega To Batching Plant And During Concrete Work Operation Workers Doing This Job Shall Be Provided With Gears So As To Avoid Inhaling Cement Dust Particles That Could Affect Their Health. Workers In Construction Site Shall Be Provided With Working Gloves, Mask Boots And Clothing To Prevent Workers From Being Contaminated With Concrete Mix. The Contractor Shall See To It That The Noise Level Of The Exhaust Mufflers Of The Equipment Shall Be At The Minimum. Otherwise, The Contractor Must Replace All The Exhaust Mufflers Of The Equipment With A New One And Or Provide Muffler Silencers. All Roads Leading The Construction Site And Batching Plant Shall Be Moist During The Entire Works Operation To Prevent The Blowing Up Of Dust Particles. During Work Operation, Precautionary Signboards Shall Be Provided By The Contractor To Prevent Accidents And Damage To The Freshly Laid Concrete.

Details: Description Request For Quotation (rfq) 1 Lot Inks And Toners Rfq No. 2025-fad-002 The Department Of Environment And Natural Resources – Environmental Management Bureau – National Capital Region (denr-emb-ncr) Hereinafter Referred To As The “purchaser” Now Requests For Submission Of Price Quotations For The Procurement Of The Aforesaid Items Described In The Technical Specifications. The Denr-emb-ncr Intends To Apply The Sum Of Nine Hundred Fifty Thousand And Five Hundred Pesos Only (php 950,500.00) Being The 1 Lotinks And Toners, Rfq No. 2025-fad-002. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. A Set Of Technical Specifications Are Provided In Attachment 1. All Items Listed Under The Purchaser’s Specifications Must Be Complied With On A Pass-fail Basis. Failure To Meet Any One Of The Requirements May Result In Rejection Of The Quotation. Small-value Procurement/shopping Procedures Will Be Conducted In Accordance With The Provisions Of The Implementing Rules And Regulations (irr) Of Republic Act 9184. It Is The Intent Of The Purchaser To Evaluate The Bid/quotation On A Per Item Basis, And Award Will Be Made To The Bid/quotation Or Combination Of Quotations Resulting In The Lowest Evaluated Quotation Meeting The Purchaser’s Technical Specifications. Quotations Must Be Delivered At The Address Below Not Later Than 12:00 P.m. Of February 17 2025. Department Of Environment And Natural Resources Environmental Management Bureau National Capital Region National Ecology Center Compound, East Avenue Diliman, Quezon City Prices Must Be Quoted In Philippine Peso And Must Include The Unit Price And Total Price, Inclusive Of All Taxes To Be Paid And Other Incidental Cost To The Delivery Site/s If The Contract Is Awarded. Bid/quotation May Be Typewritten And May Be Placed In A Sealed Envelope Marked The 1 Lot Inks And Toners, Rfq No. 2025-fad-002. Or You May Send Your Bid- Quotation Through Fax (02-9313134) Or E-mail (emb.bacsec.ncr125@gmail.com). Bids/quotations Shall Be Valid For Sixty (60) Calendar Days From The Deadline Of Submission Of Bids. The Delivery Period Shall Be Within Fifteen (15) Calendar Days From Receipt Of The Purchase Order (p.o) And/or Job Order (j.o). The Supplier Should Inform The Purchaser At Least Three (3) Days Before The Date Of Delivery. The Delivery Will Be Made Only During Working Days And Hours. Delivery Sites: See Delivery Sites Enumerated In The Quotation Form Protect Environment | Protect Life Emb-ncr Building, National Ecology Center Compound, East Ave., Diliman, Quezon City 1100 Telephone No.: (02) 8931-1331 | E-mail: Recordsncr@emb.gov.ph | Ncrsupport@emb.gov.ph Website: Www.ncr.emb.gov.ph Department Of Environment And Natural Resources Environmental Management Bureau National Capital Region National Ecology Center Compound, East Avenue, Diliman, Quezon City The Applicable Rate For Late Deliveries Is One Tenth (1/10) Of One (1) Percent Of The Cost Of The Unperformed Portion Of The Contract For Every Day Of Delay. The Maximum Deduction Shall Be Ten Percent (10%) Of The Amount Of Contract. Once The Cumulative Amount Of Liquidated Damages Reaches Ten Percent (10%) Of The Contract Amount, The Purchaser Shall Rescind The Contract Without Prejudice To Other Courses Of Action And Remedies Open To It. The Purchaser Reserves The Right To Accept Or Reject Any Quotation, And To Annul The Bidding/shopping Process Or Reject All Quotations At Any Time Prior To Contract Award, Without Thereby Incurring Any Liability To The Affected Bidder/bidders. The Purchaser Also Reserves The Right To Waive Minor Deviations/defects Or Infirmities Therein. A Minor Deviation/defect Or Infirmity Is One That Does Not Materially Affect The Overall Functionality Of The Material And The Capability Of The Supplier To Perform The Contract. The Prospective Bidder Shall Submit The Following: Signed Quotation Form Goods- Technical Specifications And Certification From Regulatory Offices, If Applicable (dole Doh And Etc.) Food Services- Menu Civil Works- Plan, Layout, And Design Proof Of Philgeps Registration; Sec Registration/dti Certificate; Business Permit; Tax Clearance Annual Income Tax Return; Preferably With Proof That The Offered Products/items Are Manufactured By An Iso-9001 And Iso14001 Company Whose Certifications Are Valid On Opening Of Proposal; Preferably In Compliance With Philippine Green Public Procurement Roadmap Of Government Procurement Policy Board (gppb); Letter Of Authenticity Of Manufacturer’s Certification That The Supplier Is An Authorized Reseller/distributor And The Items Are Covered By The Manufacturer’s Warranty Failure To Follow The Above Requirements May Result In Outright Rejection Of Submitted Quotation/s. Awarded Bidder Should Sign The Conforme Within Three (3) Working Days Upon Receipt. Failure To Conform Shall Be The Basis In The Consideration Of Appropriate Responsiveness Of The Bidder, In Which The Procuring Entity Shall Proceed To The Next Lowest Calculated And Responsive Bid. Engr. Divina C. Camarao Bac, Chairperson Attachment 1 Technical Specifications No. Purchaser’s Specifications Quantity / Uom Abc Per Unit Total Abc Rfq No. 2025-fad-002 Hp Toner Cf510a, 204a, Black Hp Toner Cf511a, 204a, Cyan Hp Toner Cf512a, 204a, Yellow Hp Toner Cf513a, 204a, Magenta Hp Toner Cf2310a, 215a, Black Hp Toner Cf2311a, 215a, Cyan Hp Toner Cf2312a, 215a, Yellow Hp Toner Cf2313a, 215a, Magenta Hp680 Ink Black Hp680 Ink Tri Color Hp678 Ink Black Hp678 Ink Tri Color Canon Pg 810 Black, Genuine Canon Cl 811 Tri Color, Genuine 30 Cartridge 50 Cartridge 50 Cartridge 50 Cartridge 20 Cartridge 15 Cartridge 15 Cartridge 15 Cartridge 60 Cartridge 50 Cartridge 20 Cartridge 10 Cartridge 30 Cartridge 30 Cartridge ₱950,500.00 ₱950,500.00 Along With Your Signed Quotation Please Submit The Ff: Philgeps Certificate Dti/ Sec Mayor’s Permit Tax Clearance Annual Income Tax Return Preferably With Proof That The Offered Products / Items Are Manufactured By An Iso-9001 And Iso-14001 Company Whose Certifications Are Valid On The Opening On Proposal. Letter Of Authenticity Of Manufacturer’s Certification That The Supplier Is An Authorized Reseller/distributor And The Items Are Covered By The Manufacturer’s Warranty. Quotation Form Date: Rfq No. Attention: Fad-procurement And Property Management Unit Department Of Environment And Natural Resources Environmental Management Bureau-national Capital Region National Ecology Center Compound East Avenue, Diliman, Quezon City 1) Having Examined The Subject Request For Quotation (rfq) Including The Technical Specifications, We, The Undersigned Offer To Supply And Deliver The Following: No. Description Quantity / Uom Deliver Y Site Unit Price (php) Total Price (php) Rfq No. 2025-fad-002 Hp Toner Cf510a, 204a, Black Hp Toner Cf511a, 204a, Cyan Hp Toner Cf512a, 204a, Yellow Hp Toner Cf513a, 204a, Magenta 30 Cartridge 50 Cartridge 50 Cartridge 50 Cartridge Emb- Ncr Hp Toner Cf2310a, 215a, Black 20 Cartridge Hp Toner Cf2311a, 215a, Cyan 15 Cartridge Hp Toner Cf2312a, 215a, Yellow 15 Cartridge Hp Toner Cf2313a, 215a, Magenta 15 Cartridge Hp680 Ink Black 60 Cartridge Hp680 Ink Tri Color 50 Cartridge Hp678 Ink Black 20 Cartridge Hp678 Ink Tri Color 10 Cartridge Canon Pg 810 Black, Genuine 30 Cartridge Canon Cl 811 Tri Color, Genuine 30 Cartridge We Undertake, If Our Quotation Or Bid Is Accepted, To Deliver The Above Goods Within The Fifteen (15)-day Delivery Period From Receipt Purchase Order (p.o) Or Job Order (j.o). We Agree To Abide By This Quotation/bid For A Period Of Sixty (60) Days After The Deadline Of Submission Specified In The Rfq. We Understand That Payment For Items Delivered Will Be Made To The Winning Supplier After The Inspection And Acceptance Of Goods Delivered. Name Of Company : Postal Address : Email Address : Telephone & Fax No. : Supplier’s Representative : Signature Over Printed Name : Account Name And Branch : Preferably Landbank Account. In Case Of Other Banks, Charges May Apply. Omnibus Sworn Statement (revised) [shall Be Submitted With The Bid] Republic Of The Philippines ) City/municipality Of ) S.s. Affidavit I, [name Of Affiant], Of Legal Age, [civil Status], [nationality], And Residing At [address Of Affiant], After Having Been Duly Sworn In Accordance With Law, Do Hereby Depose And State That: [select One, Delete The Other:] [if A Sole Proprietorship:] I Am The Sole Proprietor Or Authorized Representative Of [name Of Bidder] With Office Address At [address Of Bidder]; [if A Partnership, Corporation, Cooperative, Or Joint Venture:] I Am The Duly Authorized And Designated Representative Of [name Of Bidder] With Office Address At [address Of Bidder]; [select One, Delete The Other:] [if A Sole Proprietorship:] As The Owner And Sole Proprietor, Or Authorized Representative Of [name Of Bidder], I Have Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For [name Of The Project] Of The [name Of The Procuring Entity], As Shown In The Attached Duly Notarized Special Power Of Attorney; [if A Partnership, Corporation, Cooperative, Or Joint Venture:] I Am Granted Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For [name Of The Project] Of The [name Of The Procuring Entity], As Shown In The Attached [state Title Of Attached Document Showing Proof Of Authorization (e.g., Duly Notarized Secretary’s Certificate, Board/partnership Resolution, Or Special Power Of Attorney, Whichever Is Applicable;)]; [name Of Bidder] Is Not “blacklisted” Or Barred From Bidding By The Government Of The Philippines Or Any Of Its Agencies, Offices, Corporations, Or Local Government Units, Foreign Government/foreign Or International Financing Institution Whose Blacklisting Rules Have Been Recognized By The Government Procurement Policy Board, By Itself Or By Relation, Membership, Association, Affiliation, Or Controlling Interest With Another Blacklisted Person Or Entity As Defined And Provided For In The Uniform Guidelines On Blacklisting; Each Of The Documents Submitted In Satisfaction Of The Bidding Requirements Is An Authentic Copy Of The Original, Complete, And All Statements And Information Provided Therein Are True And Correct; [name Of Bidder] Is Authorizing The Head Of The Procuring Entity Or Its Duly Authorized Representative(s) To Verify All The Documents Submitted; Consanguinity Or Affinity Up To The Third Civil Degree; [if A Partnership Or Cooperative:] None Of The Officers And Members Of [name Of Bidder] Is Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; [if A Corporation Or Joint Venture:] None Of The Officers, Directors, And Controlling Stockholders Of [name Of Bidder] Is Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; [name Of Bidder] Complies With Existing Labor Laws And Standards; And [name Of Bidder] Is Aware Of And Has Undertaken The Responsibilities As A Bidder In Compliance With The Philippine Bidding Documents, Which Includes: Carefully Examining All Of The Bidding Documents; Acknowledging All Conditions, Local Or Otherwise, Affecting The Implementation Of The Contract; Making An Estimate Of The Facilities Available And Needed For The Contract To Be Bid, If Any; And Inquiring Or Securing Supplemental/bid Bulletin(s) Issued For The [name Of The Project]. [name Of Bidder] Did Not Give Or Pay Directly Or Indirectly, Any Commission, Amount, Fee, Or Any Form Of Consideration, Pecuniary Or Otherwise, To Any Person Or Official, Personnel Or Representative Of The Government In Relation To Any Procurement Project Or Activity. In Case Advance Payment Was Made Or Given, Failure To Perform Or Deliver Any Of The Obligations And Undertakings In The Contract Shall Be Sufficient Grounds To Constitute Criminal Liability For Swindling (estafa) Or The Commission Of Fraud With Unfaithfulness Or Abuse Of Confidence Through Misappropriating Or Converting Any Payment Received By A Person Or Entity Under An Obligation Involving The Duty To Deliver Certain Goods Or Services, To The Prejudice Of The Public And The Government Of The Philippines Pursuant To Article 315 Of Act No. 3815 S. 1930, As Amended, Or The Revised Penal Code. In Witness Whereof, I Have Hereunto Set My Hand This Day Of , 20 At , Philippines. [insert Name Of Bidder Or Its Authorized Representative] [insert Signatory’s Legal Capacity] Affiant [jurat] [format Shall Be Based On The Latest Rules On Notarial] Purchase Request Appendix 60 Department Of Environment & Natural Resources Environmental Management Bureau National Capital Region Fund Cluster: Office/section: Fad-ppmu Pr No.: 2025-01-031 Responsibility Center Code : Date: January 20, 2025 Stock/ Property No. Unit Item Description Quantity Unit Cost Total Cost Cartridge Hp Toner Cf510a, 204a, Black 30 ₱ 3,200.00 ₱96,000.00 Cartridge Hp Toner Cf511a, 204a, Cyan 50 ₱ 3,400.00 ₱170,000.00 Cartridge Hp Toner Cf512a, 204a, Yellow 50 ₱ 3,400.00 ₱170,000.00 Cartridge Hp Toner Cf513a, 204a, Magenta 50 ₱ 3,400.00 ₱170,000.00 Cartridge Hp Toner Cf2310a, 215a, Black 20 ₱ 3,000.00 ₱60,000.00 Cartridge Hp Toner Cf2311a, 215a, Cyan 15 ₱ 3,200.00 ₱48,000.00 Cartridge Hp Toner Cf2312a, 215a, Yellow 15 ₱ 3,200.00 ₱48,000.00 Cartridge Hp Toner Cf2313a, 215a, Magenta 15 ₱ 3,200.00 ₱48,000.00 Cartridge Hp680 Ink Black 60 ₱ 500.00 ₱30,000.00 Cartridge Hp680 Ink Tri Color 50 ₱ 500.00 ₱25,000.00 Cartridge Hp678 Ink Black 20 ₱ 650.00 ₱13,000.00 Cartridge Hp678 Ink Tri Color 10 ₱ 650.00 ₱6,500.00 Cartridge Canon Pg 810 Black, Genuine 30 ₱ 1,000.00 ₱30,000.00 Cartridge Canon Cl 811 Tri Color, Genuine 30 ₱ 1,200.00 ₱36,000.00 Total ₱950,500.00 Charged To Gaa - Regular Fund Code: Funds Available: Christine Joy J. Acaban Unit Head, Budget Purpose: For Official Use Of Emb Ncr Requested By: Approved By: Signature: Printed Name: Gemma G. Carino Engr. Maria Dorica Naz-hipe, Ceso V Designation: Chief,fad Regional Director Date: Purchase Request Appendix 60 Department Of Environment & Natural Resources Environmental Management Bureau National Capital Region Fund Cluster: Office/section: Fad-ppmu Pr No.: 2025-01-031 Responsibility Center Code : Date: January 20, 2025 Stock/ Property No. Unit Item Description Quantity Unit Cost Total Cost Cartridge Hp Toner Cf510a, 204a, Black 30 ₱ 3,200.00 ₱96,000.00 Cartridge Hp Toner Cf511a, 204a, Cyan 50 ₱ 3,400.00 ₱170,000.00 Cartridge Hp Toner Cf512a, 204a, Yellow 50 ₱ 3,400.00 ₱170,000.00 Cartridge Hp Toner Cf513a, 204a, Magenta 50 ₱ 3,400.00 ₱170,000.00 Cartridge Hp Toner Cf2310a, 215a, Black 20 ₱ 3,000.00 ₱60,000.00 Cartridge Hp Toner Cf2311a, 215a, Cyan 15 ₱ 3,200.00 ₱48,000.00 Cartridge Hp Toner Cf2312a, 215a, Yellow 15 ₱ 3,200.00 ₱48,000.00 Cartridge Hp Toner Cf2313a, 215a, Magenta 15 ₱ 3,200.00 ₱48,000.00 Cartridge Hp680 Ink Black 60 ₱ 500.00 ₱30,000.00 Cartridge Hp680 Ink Tri Color 50 ₱ 500.00 ₱25,000.00 Cartridge Hp678 Ink Black 20 ₱ 650.00 ₱13,000.00 Cartridge Hp678 Ink Tri Color 10 ₱ 650.00 ₱6,500.00 Cartridge Canon Pg 810 Black, Genuine 30 ₱ 1,000.00 ₱30,000.00 Cartridge Canon Cl 811 Tri Color, Genuine 30 ₱ 1,200.00 ₱36,000.00 Total ₱950,500.00 Charged To Gaa - Regular Fund Code: Funds Available: Christine Joy J. Acaban Unit Head, Budget Purpose: For Official Use Of Emb Ncr Requested By: Approved By: Signature: Printed Name: Gemma G. Carino Engr. Maria Dorica Naz-hipe, Ceso V Designation: Chief,fad Regional Director Date: Engr. Christian Dale E. Formeloza App-cse 2025 Form - Other Items Annual Procurement Plan - Commom-use Supplies And Equipment (app-cse) 2025 Form - Other Items Agency Code/uacs: Contact Person: Agency Name: Designation: Organization Type: Email: Region: Contact Number: Address: Introduction: Reminders: This Form Shall Be Utilized By Government Agencies For Items That Are Not Available In The Ps-dbm Catalogue But Are Regularly Purchased From Other Sources. Information Given In This Form Will Serve As A Survey To Identify The Items That May Be Considered As Cse By The Ps-dbm. The App-cse 2025 Form - Other Items Must Be Accomplished Using Excel Only. The App-cse Form - Other Items Shall Be Deemed Incorrect Or Invalid If The Form Used Is In Other Than The Prescribed Format Which Can Be Downloaded In The Ps-dbm Website (www.ps-philgeps.gov.ph). All Information Must Be Provided Accurately. To Fill-out, Find The Item In The 'list Of Items - 1' Tab Of This File Then Type The Desired Product In The Search Bar (working Only For Mirosoft Excel 2013 Or Higher). Copy The Description, Right Click Then Paste As Values In The Dedicated Column Of The Form 'item Description". You May Also Use The 'list Of Items - 2' Then Press Ctrl + F To Find The Item. If It Is Necessary To Input The Details Of The Product, You May Type It In The 'specification' Column Provided Beside The Item Description.the First One Hundred (100) Rows Are Dedicated Only For This Procedure, While The Remaining Rows Is Open For Editing. You Can Insert Additional Rows After The First 100 If Necessary. Upload The App-cse 2025 Form - Other Items Through The Google Forms Link: Https://shorturl.at/adeqo For Further Assistance Or Clarification, Agencies May Contact The Marketing And Sales Division Of Ps-dbm Through Its Mobile Numbers 0918-2954426 (smart) Or 0962-8255199 (smart), Or Email Appcse.helpdesk@ps- Philgeps.gov.ph, Or Visit The Ps-dbm Website (www.ps-philgeps.gov.ph) For The Guide On How To Fill-out The App-cse The App-cse For Fy 2025 Must Be Submitted On Or Before July 31, 2024 No. Unspsc Item Description Specification (input Specific Features Or Composition Of The Item Such As Dimensions, Color, Or Functions) Unit Of Measure Monthly Quantity Requirement Total Quantity For The Year Price Total Amount For The Year Jan Feb Mar Q1 Q1 Amount April May June Q2 Q2 Amount July Aug Sept Q3 Q3 Amount Oct Nov Dec Q4 Q4 Amount Other Items Not Available At Ps-dbm But Are Regularly Purchased From Other Sources (note: Please Indicate Price Of Items) 1 - Ink Cartridge, Canon Pg-810 Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 990.00 0.00 2 - Ink Cartridge, Canon Cl-811 Tri-color Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,300.00 0.00 3 - Toner Cartridge, Canon 054h, 3028c001 Black Cart 1 0 1 2 13,000.00 0 1 0 1 6,500.00 1 1 0 2 13,000.00 0 0 0 0 0.00 5 6,500.00 32,500.00 4 - Toner Cartridge, Canon 054h, 3025c001 Yellow Cart 0 1 0 1 6,500.00 0 1 0 1 6,500.00 0 1 0 1 6,500.00 0 1 0 1 6,500.00 4 6,500.00 26,000.00 5 - Toner Cartridge, Canon 054h, 3026c001 Magenta Cart 0 1 0 1 6,500.00 0 1 0 1 6,500.00 0 1 0 1 6,500.00 0 1 0 1 6,500.00 4 6,500.00 26,000.00 6 - Toner Cartridge, Canon 054h, 3027c001 Cyan Cart 0 1 0 1 6,500.00 0 1 0 1 6,500.00 0 1 0 1 6,500.00 0 1 0 1 6,500.00 4 6,500.00 26,000.00 7 - Ink Bottle, Hp Gt53, 1vv22aa Black Bottle 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 8 - Ink Bottle, Hp Gt52, M0h54aa Cyan Bottle 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 9 - Ink Bottle, Hp Gt52, M0h55aa Magenta Bottle 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 10 - Ink Bottle, Hp Gt52, M0h56aa Yellow Bottle 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 11 - Toner Cartridge, Hp 202a, Cf500a Black Cart 2 2 1 5 21,000.00 2 2 1 5 21,000.00 2 2 1 5 21,000.00 2 2 1 5 21,000.00 20 4,200.00 84,000.00 12 - Toner Cartridge, Hp 202a, Cf501a Cyan Cart 2 2 1 5 25,000.00 2 2 1 5 25,000.00 2 2 1 5 25,000.00 2 2 1 5 25,000.00 20 5,000.00 100,000.00 13 - Toner Cartridge, Hp 202a, Cf502a Yellow Cart 2 2 1 5 25,000.00 2 2 1 5 25,000.00 2 2 1 5 25,000.00 2 2 1 5 25,000.00 20 5,000.00 100,000.00 14 - Toner Cartridge, Hp 202a, Cf503a Magenta Cart 2 2 1 5 25,000.00 2 2 1 5 25,000.00 2 2 1 5 25,000.00 2 2 1 5 25,000.00 20 5,000.00 100,000.00 15 - Toner Cartridge, Hp 204a, Cf510a Black Cart 10 10 10 30 96,000.00 10 10 10 30 96,000.00 5 5 5 15 48,000.00 5 5 5 15 48,000.00 90 3,200.00 288,000.00 16 - Toner Cartridge, Hp204a, Cf511a Cyan Cart 5 5 5 15 53,250.00 5 5 5 15 53,250.00 5 5 5 15 53,250.00 5 5 5 15 53,250.00 60 3,550.00 213,000.00 17 - Toner Cartridge, Hp204a, Cf512a Yellow Cart 5 5 5 15 53,250.00 5 5 5 15 53,250.00 5 5 5 15 53,250.00 5 5 5 15 53,250.00 60 3,550.00 213,000.00 18 - Toner Cartridge, Hp204a, Cf513a Magenta Cart 5 5 5 15 53,250.00 5 5 5 15 53,250.00 5 5 5 15 53,250.00 5 5 5 15 53,250.00 60 3,550.00 213,000.00 19 - Toner Cartridge, Hp 107a, W1107a Black Cart 0 5 5 10 25,000.00 0 5 5 10 25,000.00 0 5 5 10 25,000.00 0 5 5 10 25,000.00 40 2,500.00 100,000.00 20 - Toner Cartridge, Hp 85a, Ce285a Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 21 - Toner Cartridge, Hp 79a, Cf279a Black Cart 5 0 5 10 39,750.00 0 0 0 0 0.00 5 0 5 10 39,750.00 0 0 0 0 0.00 20 3,975.00 79,500.00 22 - Toner Cartridge, Hp 215a, W2310a Black Cart 5 5 2 12 37,200.00 5 5 2 12 37,200.00 5 5 2 12 37,200.00 5 5 2 12 37,200.00 48 3,100.00 148,800.00 23 - Toner Cartridge, Hp215a, W2311a Cyan Cart 5 5 2 12 39,600.00 5 5 2 12 39,600.00 5 5 2 12 39,600.00 5 5 2 12 39,600.00 48 3,300.00 158,400.00 24 - Toner Cartridge, Hp215a, W2312a Yellow Cart 5 5 2 12 39,600.00 5 5 2 12 39,600.00 5 5 2 12 39,600.00 5 5 2 12 39,600.00 48 3,300.00 158,400.00 25 - Toner Cartridge, Hp215a, W2313a Magenta Cart 5 5 2 12 39,600.00 5 5 2 12 39,600.00 5 5 2 12 39,600.00 5 5 2 12 39,600.00 48 3,300.00 158,400.00 26 - Ink Cartridge, Hp 678, Hpcz107aa Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 600.00 0.00 27 - Ink Cartridge, Hp 678, Hpcz108aa Tri-color Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 600.00 0.00 28 - Ink Cartridge, Hp 680, F6v27aa Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 600.00 0.00 29 - Ink Cartridge, Hp 680, F6v26aa Tri-color Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 600.00 0.00 30 - Ink Cartridge, Hp 955, L0s60aa Black Cart 1 1 1 3 4,200.00 1 1 1 3 4,200.00 1 1 1 3 4,200.00 1 1 1 3 4,200.00 12 1,400.00 16,800.00 31 - Ink Cartridge, Hp 955, L0s51aa Cyan Cart 1 1 1 3 3,300.00 1 1 1 3 3,300.00 1 1 1 3 3,300.00 1 1 1 3 3,300.00 12 1,100.00 13,200.00 32 - Ink Cartridge, Hp 955, L0s57aa Yellow Cart 1 1 1 3 3,300.00 1 1 1 3 3,300.00 1 1 1 3 3,300.00 1 1 1 3 3,300.00 12 1,100.00 13,200.00 33 - Ink Cartridge, Hp 955, L0s54aa Magenta Cart 1 1 1 3 3,300.00 1 1 1 3 3,300.00 1 1 1 3 3,300.00 1 1 1 3 3,300.00 12 1,100.00 13,200.00 34 - Toner, Epson Wf-c5790 (black, Cyan, Yellow, Magenta) Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 15,000.00 0.00 35 - Ink Cartridge, Epson T289 Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 36 - Ink Cartridge, Epson T290 Tri-color Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 37 - Ink Bottle, Epson 003, T00v100 Black Bottle 5 5 5 15 3,000.00 5 5 5 15 3,000.00 5 5 5 15 3,000.00 5 5 5 15 3,000.00 60 200.00 12,000.00 38 - Ink Bottle, Epson 003, T00v200 Cyan Bottle 5 0 5 10 2,000.00 5 0 5 10 2,000.00 5 0 5 10 2,000.00 5 0 5 10 2,000.00 40 200.00 8,000.00 39 - Ink Bottle, Epson 003, T00v300 Magenta Bottle 5 0 5 10 2,000.00 5 0 5 10 2,000.00 5 0 5 10 2,000.00 5 0 5 10 2,000.00 40 200.00 8,000.00 40 - Ink Bottle, Epson 003, T00v400 Yellow Bottle 5 0 5 10 2,000.00 5 0 5 10 2,000.00 5 0 5 10 2,000.00 5 0 5 10 2,000.00 40 200.00 8,000.00 41 - Ink Bottle, Epson 001, C13t03y100 Black Bottle 0 0 1 1 600.00 0 0 1 1 600.00 0 0 1 1 600.00 0 1 1 2 1,200.00 5 600.00 3,000.00 42 - Ink Bottle, Epson 001, C13t03y200 Cyan Bottle 0 0 1 1 400.00 0 0 1 1 400.00 0 0 1 1 400.00 0 1 1 2 800.00 5 400.00 2,000.00 43 - Ink Bottle, Epson 001, C13t03y300 Magenta Bottle 0 0 1 1 400.00 0 0 1 1 400.00 0 0 1 1 400.00 0 1 1 2 800.00 5 400.00 2,000.00 44 - Ink Bottle, Epson 001, C13t03y400 Yellow Bottle 0 0 1 1 400.00 0 0 1 1 400.00 0 0 1 1 400.00 0 1 1 2 800.00 5 400.00 2,000.00 45 - Ink Bottle, Epson 005, T03q100 Black Bottle 1 1 1 3 2,400.00 1 1 1 3 2,400.00 1 1 1 3 2,400.00 1 1 1 3 2,400.00 12 800.00 9,600.00 46 - Ink Bottle, Epson 664, C13t664100 Black Bottle 0 0 5 5 2,000.00 0 0 10 10 4,000.00 0 0 5 5 2,000.00 0 0 10 10 4,000.00 30 400.00 12,000.00 47 - Ink Bottle, Epson 664, C13t664200 Cyan Bottle 0 0 5 5 2,000.00 0 0 5 5 2,000.00 0 0 5 5 2,000.00 0 0 5 5 2,000.00 20 400.00 8,000.00 48 - Ink Bottle, Epson 664, C13t664300 Magenta Bottle 0 0 5 5 2,000.00 0 0 5 5 2,000.00 0 0 5 5 2,000.00 0 0 5 5 2,000.00 20 400.00 8,000.00 49 - Ink Bottle, Epson 664, C13t664400 Yellow Bottle 0 0 5 5 2,000.00 0 0 5 5 2,000.00 0 0 5 5 2,000.00 0 0 5 5 2,000.00 20 400.00 8,000.00 No. Unspsc Item Description Specification (input Specific Features Or Composition Of The Item Such As Dimensions, Color, Or Functions) Unit Of Measure Monthly Quantity Requirement Total Quantity For The Year Price Total Amount For The Year Jan Feb Mar Q1 Q1 Amount April May June Q2 Q2 Amount July Aug Sept Q3 Q3 Amount Oct Nov Dec Q4 Q4 Amount Other Items Not Available At Ps-dbm But Are Regularly Purchased From Other Sources (note: Please Indicate Price Of Items) 50 - Ink Bottle, Epson 673, T6731 Black Bottle 0 0 0 0 0.00 1 0 0 1 0.00 0 0 0 0 0.00 1 0 0 1 0.00 2 0.00 0.00 51 - Ink Bottle, Epson 673, T6732 Cyan Bottle 0 0 0 0 0.00 1 0 0 1 0.00 0 0 0 0 0.00 1 0 0 1 0.00 2 0.00 0.00 52 - Ink Bottle, Epson 673, T6733 Magenta Bottle 0 0 0 0 0.00 1 0 0 1 0.00 0 0 0 0 0.00 1 0 0 1 0.00 2 0.00 0.00 53 - Ink Bottle, Epson 673, T6734 Yellow Bottle 0 0 0 0 0.00 1 0 0 1 0.00 0 0 0 0 0.00 1 0 0 1 0.00 2 0.00 0.00 54 - Ink Bottle, Epson 673, T6735 Light Cyan Bottle 0 0 0 0 0.00 1 0 0 1 0.00 0 0 0 0 0.00 1 0 0 1 0.00 2 0.00 0.00 55 - Ink Bottle, Epson 673, T6736 Light Magenta Bottle 0 0 0 0 0.00 1 0 0 1 0.00 0 0 0 0 0.00 1 0 0 1 0.00 2 0.00 0.00 56 - Ribbon Cartridge, Epson Lx310, S015632 Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 57 - Ribbon Cartridge, Epson Lq2190, S015531/s015086 Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 58 - Toner Cartridge, Lexmark Network Printer, 58d3h00 Black Cart 0 0 3 3 54,000.00 0 0 0 0 0.00 0 0 3 3 54,000.00 0 0 0 0 0.00 6 18,000.00 108,000.00 59 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 60 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 61 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 62 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 63 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 64 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 65 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 66 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 67 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 68 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 69 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 70 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 71 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 72 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 73 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 74 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 75 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 76 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 77 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 78 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 79 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 80 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 81 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 82 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 83 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 84 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 85 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 86 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 87 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 88 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 89 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 90 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 91 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 92 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 93 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 94 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 95 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 96 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 97 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 98 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 99 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 100 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 No. Unspsc Item Description Specification (input Specific Features Or Composition Of The Item Such As Dimensions, Color, Or Functions) Unit Of Measure Monthly Quantity Requirement Total Quantity For The Year Price Total Amount For The Year Jan Feb Mar Q1 Q1 Amount April May June Q2 Q2 Amount July Aug Sept Q3 Q3 Amount Oct Nov Dec Q4 Q4 Amount Other Items Not Available At Ps-dbm But Are Regularly Purchased From Other Sources (note: Please Indicate Price Of Items) A. Total ₱ 2,480,000.00 B. Additional Provision For Inflation (10% Of Total) ₱ 248,000.00 C. Additional Provision For Transport And Freight Cost (if Applicable) ₱ - D. Grand Total (a + B+ C) ₱ 2,728,000.00 E. Approved Budget By The Agency Head In Figures And Words: We Hereby Warrant That The Total Amount Reflected In This Annual Procurement Plan To Procure The Listed Common-use Supplies, Materials, And Equipment Has Been Included In Or Is Within Our Approved Budget For The Year. Prepared By: Certified Funds Available / Certified Appropriate Funds Available: Approved By: Jodi Hani C. Leal / Cesar D. Tolentino Property/supply Officer Accountant / Budget Officer Date Prepared: Introduction: App-cse 2025 Form Annual Procurement Plan - Commom-use Supplies And Equipment (app-cse) 2025 Form This Form Contains The Common-use Supplies And Equipment (cse) Being Carried By The Procurement Service – Department Of Budget And Management (ps-dbm) That Shall Be Purchased By Government Agencies. Consistent With The Dbm Circular Letter Nos. 2011-6 And 2011-6-a Dated 25 August 2011 And 28 September 2011, Respectively, The App-cse Shall Serve As The Agency’s Annual Procurement Request For All Its Cse Requirements. Only Agencies With Uploaded App-cse In The Modernized Philippine Government Electronic Procurement System (mphilgeps) Will Be Able To Purchase Cse From The Ps-dbm. Note That The Items Listed On This Form Have Been Arranged In Accordance With The United Nations Standard Products And Services Code (unspsc). Reminders: 1.0 2.0 3.0 The App-cse Form Must Be Accomplished Using Microsoft Excel Format. The App-cse Shall Be Deemed Incorrect Or Invalid If The Form Used Is Other Than The Prescribed Format Which Is Downloadable From The Mphilgeps And Downloads Page Of Ps-dbm Website (www.ps-philgeps.gov.ph). All Information Must Be Provided Accurately. Kindly Refer To The Cse Catalogue On The Ps-dbm Website (www.ps-philgeps.gov.ph) Under The "what We Sell" Tab For The Detailed Technical Specifications And Sample Photo Of The Items. 4.0 Do Not Delete, Add, Or Revise Any Items Or Rows On This Form, Otherwise The Form Will Be Deemed Invalid. 5.0 6.0 7.0 8.0 For Items Not Included On The List Of Part Ii, A Separate File, With The File Name App-cse 2025 Form - Other Items, Can Be Downloaded From The Downloads Page Of Ps-dbm Website (www.ps-philgeps.gov.ph) And Must Be Submitted To Ps-dbm Through This Link: Https://shorturl.at/adeqo. Instructions On How To Fill-out Is Included In The Reminders Of The Form. Once Signed And Approved By The Property/supply Officer, Accountant/budget Officer, And Head Of The Agency/office, Kindly Upload The Soft Copy Of The App-cse In Microsoft Excel Format As Well As The Original Signed Copy In Portable Document Format (pdf) To The Agency's Mphilgeps Account On Or Before The Prescribed Period Or Deadline. Any App-cse Form That Is Unsigned Or Has Incomplete Signature Shall Be Deemed Invalid. Should There Be Changes In The Agency’s Cse Requirements, The Agency May Edit Their Uploaded App-cse Directly On Their Mphilgeps Account. However, The Agency Must Ensure That A Signed And Approved Copy Of The Supplemental App-cse Form Is Available. Note That All Cse Requirements In Excess Of The Quantities Indicated In The Original App-cse Form Will Not Be Served If Not Covered By A Supplemental App-cse. For Further Assistance Or Clarification, Agencies May Contact The Marketing And Sales Division Of Ps-dbm Through Its Mobile Numbers 0918-2954426 (smart) Or 0962-8255199 (smart), Or Email Appcse.helpdesk@ps-philgeps.gov.ph, Or Visit The Ps-dbm Website (www.ps-philgeps.gov.ph) For The Guide On How To Fill-out The App-cse. Environmental Management B Ncr Nec Cmpd., East Ave., Brgy. Central, Quezon City Joy Anne Marie A. Mancera Head, Ppmu Ppmudivision03@gmail.com 8931-13-31 Note: The App-cse For Fy 2025 Must Be Submitted On Or Before 31 July 2024. Department/bureau/office: Agency Code/uacs: Contact Person: Region: Organization Type: Position: Address: E-mail : Telephone/mobile Nos: Item & Specifications Unit Of Measure Monthly Quantity Requirement Total Quantity For The Year Price Total Amount For The Year Jan Feb Mar Q1 Q1 Amount April May June Q2 Q2 Amount July Aug Sept Q3 Q3 Amount Oct Nov Dec Q4 Q4 Amount Part I. Available At Ps-dbm (main Warehouse And Depots) Alcohol Or Acetone Based Antiseptics 1 12191601-al-e04 Alcohol, Ethyl, 500 Ml Bottle 0 0 0 0 0.00 70 70 70 210 10,590.30 0 0 0 0 0.00 70 70 70 210 10,590.30 420 50.43 21,180.60 2 12191601-al-e03 Alcohol, Ethyl, 1 Gallon Gallon 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 357.09 0.00 Arts And Crafts Equipment And Accessories And Supplies 3 60121413-cb-p01 Clearbook, A4 Size Piece 0 12 0 12 421.92 0 12 0 12 421.92 0 12 0 12 421.92 0 12 0 12 421.92 48 35.16 1,687.68 4 60121413-cb-p02 Clearbook, Legal Size Piece 0 12 0 12 436.32 0 12 0 12 436.32 0 12 0 12 436.32 0 12 0 12 436.32 48 36.36 1,745.28 5 60121534-er-p01 Eraser, Plastic/rubber Piece 0 10 0 10 82.60 0 10 0 10 82.60 0 10 0 10 82.60 0 10 0 10 82.60 40 8.26 330.40 6 60121524-sp-g01 Sign Pen, Extra Fine Tip, Black Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 22.20 0.00 7 60121524-sp-g04 Sign Pen, Fine Tip, Black Piece 30 30 30 90 4,024.80 30 30 30 90 4,024.80 30 30 30 90 4,024.80 30 30 30 90 4,024.80 360 44.72 16,099.20 8 60121524-sp-g07 Sign Pen, Medium Tip, Black Piece 30 30 30 90 5,148.00 30 30 30 90 5,148.00 30 30 30 90 5,148.00 30 30 30 90 5,148.00 360 57.20 20,592.00 9 60121524-sp-g02 Sign Pen, Extra Fine Tip, Blue Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 22.20 0.00 10 60121524-sp-g05 Sign Pen, Fine Tip, Blue Piece 50 50 50 150 6,708.00 50 50 50 150 6,708.00 50 50 50 150 6,708.00 50 50 50 150 6,708.00 600 44.72 26,832.00 11 60121524-sp-g08 Sign Pen, Medium Tip, Blue Piece 80 80 80 240 13,728.00 80 80 80 240 13,728.00 80 80 80 240 13,728.00 80 80 80 240 13,728.00 960 57.20 54,912.00 12 60121524-sp-g03 Sign Pen, Extra Fine Tip, Red Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 22.20 0.00 13 60121524-sp-g06 Sign Pen, Fine Tip, Red Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 45.76 0.00 14 60121524-sp-g09 Sign Pen, Medium Tip, Red Piece 12 12 12 36 2,059.20 12 12 12 36 2,059.20 12 12 12 36 2,059.20 12 12 12 36 2,059.20 144 57.20 8,236.80 15 60121124-wr-p01 Wrapping Paper Pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 161.20 0.00 Audio And Visual Equipment And Supplies 16 45121517-do-c03 Document Camera Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 23,623.60 0.00 17 45111609-mm-p01 Multimedia Projector Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 16,588.00 0.00 Batteries And Cells And Accessories 18 26111702-bt-a02 Battery, Dry Cell, Size Aa Pack 100 100 100 300 6,147.00 100 100 100 300 6,147.00 100 100 100 300 6,147.00 100 100 100 300 6,147.00 1200 20.49 24,588.00 19 26111702-bt-a01 Battery, Dry Cell, Size Aaa Pack 100 100 100 300 5,502.00 100 100 100 300 5,502.00 100 100 100 300 5,502.00 100 100 100 300 5,502.00 1200 18.34 22,008.00 Cleaning Equipment And Supplies 20 47131812-af-a01 Air Freshener Can 12 12 12 36 3,143.16 12 12 12 36 3,143.16 12 12 12 36 3,143.16 12 12 12 36 3,143.16 144 87.31 12,572.64 21 47131604-br-s01 Broom (walis Tambo) Piece 8 8 8 24 2,995.20 8 8 8 24 2,995.20 8 8 8 24 2,995.20 8 8 8 24 2,995.20 96 124.80 11,980.80 22 47131604-br-t01 Broom (walis Ting-ting) Piece 12 12 12 36 936.00 12 12 12 36 936.00 12 12 12 36 936.00 12 12 12 36 936.00 144 26.00 3,744.00 23 47131829-tb-c01 Cleaner, Toilet Bowl And Urinal Bottle 10 10 10 30 1,248.00 10 10 10 30 1,248.00 10 10 10 30 1,248.00 10 10 10 30 1,248.00 120 41.60 4,992.00 24 47131805-cl-p01 Cleanser, Scouring Powder Plastic Container 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 23.92 0.00 Item & Specifications Unit Of Measure Monthly Quantity Requirement Total Quantity For The Year Price Total Amount For The Year Jan Feb Mar Q1 Q1 Amount April May June Q2 Q2 Amount July Aug Sept Q3 Q3 Amount Oct Nov Dec Q4 Q4 Amount 25 47131811-de-b02 Detergent Bar Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 9.34 0.00 26 47131811-de-p02 Detergent Powder, All Purpose Pouch 35 35 35 105 5,678.40 35 35 35 105 5,678.40 35 35 35 105 5,678.40 35 35 35 105 5,678.40 420 54.08 22,713.60 27 47131803-ds-a01 Disinfectant Spray Can 12 12 12 36 5,036.04 12 12 12 36 5,036.04 12 12 12 36 5,036.04 12 12 12 36 5,036.04 144 139.89 20,144.16 28 47131601-du-p01 Dust Pan Piece 0 0 10 10 468.00 0 0 10 10 468.00 0 0 10 10 468.00 0 0 10 10 468.00 40 46.80 1,872.00 29 47131802-fw-p03 Floor Wax, Paste Type, Red Can 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 309.76 0.00 30 47131830-fc-a01 Furniture Cleaner Can 4 4 4 12 1,696.68 4 4 4 12 1,696.68 4 4 4 12 1,696.68 4 4 4 12 1,696.68 48 141.39 6,786.72 31 73101612-hs-l01 Hand Soap, Liquid, 500ml Bottle 40 40 40 120 5,154.00 40 40 40 120 5,154.00 40 40 40 120 5,154.00 40 40 40 120 5,154.00 480 42.95 20,616.00 32 47121804-mp-b01 Mop Bucket Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 2,288.00 0.00 33 47131501-rg-c01 Rags Kilo 0 0 0 0 0.00 0 0 0 0 0.00 0 12 0 12 833.64 0 12 0 12 833.64 24 69.47 1,667.28 34 47131602-sc-n01 Scouring Pad Pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 85.63 0.00 35 47121701-tb-p04 Trashbag, Xxl Size Roll/pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 130.00 0.00 36 47121701-tb-p05 Trashbag, Large Size Roll/pack 50 50 50 150 8,892.00 50 50 50 150 8,892.00 50 50 50 150 8,892.00 50 50 50 150 8,892.00 600 59.28 35,568.00 37 47121701-tb-p06 Trashbag, Xl Size Roll/pack 50 50 50 150 13,884.00 50 50 50 150 13,884.00 50 50 50 150 13,884.00 50 50 50 150 13,884.00 600 92.56 55,536.00 38 47121702-wb-p01 Wastebasket Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 43.68 0.00 Color Compounds And Dispersions 39 12171703-si-p01 Ink, For Stamp Pad Bottle 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 28.79 0.00 Consumer Electronics 40 52161535-dv-r02 Digital Voice Recorder Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 7,339.16 0.00 Films 41 13111203-ac-f01 Acetate Roll 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,243.84 0.00 42 13111201-cf-p02 Carbon Film, Legal Size Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 351.83 0.00 Fire Fighting Equipment 43 46191601-fe-m01 Fire Extinguisher, Dry Chemical Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,144.00 0.00 Flag Or Accessories 44 55121905-ph-f01 Philippine National Flag Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 1 0 1 284.84 0 0 0 0 0.00 1 284.84 284.84 Furniture And Furnishings 45 56101504-cm-b01 Monobloc Chair, Beige Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 341.12 0.00 46 56101504-cm-w01 Monobloc Chair, White Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 341.12 0.00 Heating And Ventilation And Air Circulation 47 40101604-ef-c01 Electric Fan, Ceiling Mount, Orbit Type Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,222.00 0.00 48 40101604-ef-g01 Electric Fan, Industrial, Ground Type Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,109.68 0.00 49 40101604-ef-s01 Electric Fan, Stand Type Unit 0 0 1 1 1,560.00 0 0 1 1 1,560.00 0 0 1 1 1,560.00 0 0 1 1 1,560.00 4 1,560.00 6,240.00 50 40101604-ef-w01 Electric Fan, Wall Mount Unit 0 0 1 1 901.68 0 0 1 1 901.68 0 0 1 1 901.68 0 0 1 1 901.68 4 901.68 3,606.72 Information And Communication Technology (ict) Equipment And Devices And Accessories 51 43211507-dsk003 Desktop, For Basic Users Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 24,793.60 0.00 52 43211507-dsk004 Desktop, For Mid-range Users Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 42,390.40 0.00 53 43201827-hd-x02 External Hard Drive Unit 5 0 5 10 30,149.60 5 0 5 10 30,149.60 5 0 5 10 30,149.60 5 0 5 10 30,149.60 40 3,014.96 120,598.40 54 43202010-fd-u04 Flash Drive Piece 5 5 5 15 2,291.10 5 5 5 15 2,291.10 5 5 5 15 2,291.10 5 5 5 15 2,291.10 60 152.74 9,164.40 55 43211503-lap004 Laptop Computer, For Mid-range Users Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 42,380.00 0.00 56 43211503-lap003 Laptop Computer, Lightweight Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 46,800.00 0.00 57 43211708-mo-o02 Computer Mouse, Wireless Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 161.92 0.00 58 43212105-pr-l01 Printer, Laser, Monochrome Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 2,636.89 0.00 Lighting And Fixtures And Accessories 59 39101628-lb-l01 Light-emitting Diode (led) Light Bulb, 7 Watts Piece 12 12 12 36 2,721.96 12 12 12 36 2,721.96 12 12 12 36 2,721.96 12 12 12 36 2,721.96 144 75.61 10,887.84 60 39101628-lt-l01 Light-emitting Diode (led) Linear Tube, 18 Watts Piece 30 30 30 90 18,523.80 30 30 30 90 18,523.80 30 30 30 90 18,523.80 30 30 30 90 18,523.80 360 205.82 74,095.20 Manufacturing Components And Supplies 61 31201610-gl-j02 Glue, All-purpose Bottle 0 0 10 10 621.40 0 0 10 10 621.40 0 0 10 10 621.40 0 0 10 10 621.40 40 62.14 2,485.60 62 31151804-sw-h01 Staple Wire, Heavy Duty (binder Type), 23/13 Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 36.40 0.00 63 31151804-sw-s01 Staple Wire, Standard Box 10 10 10 30 712.80 10 10 10 30 712.80 10 10 10 30 712.80 10 10 10 30 712.80 120 23.76 2,851.20 Item & Specifications Unit Of Measure Monthly Quantity Requirement Total Quantity For The Year Price Total Amount For The Year Jan Feb Mar Q1 Q1 Amount April May June Q2 Q2 Amount July Aug Sept Q3 Q3 Amount Oct Nov Dec Q4 Q4 Amount 64 31201502-ta-e02 Tape, Electrical Roll 0 0 20 20 389.00 0 0 20 20 389.00 0 0 20 20 389.00 0 0 20 20 389.00 80 19.45 1,556.00 65 31201503-ta-m01 Tape, Masking, 24mm Roll 30 30 30 90 5,011.20 30 30 30 90 5,011.20 30 30 30 90 5,011.20 30 30 30 90 5,011.20 360 55.68 20,044.80 66 31201503-ta-m02 Tape, Masking, 48 Mm Roll 50 50 50 150 18,174.00 50 50 50 150 18,174.00 50 50 50 150 18,174.00 50 50 50 150 18,174.00 600 121.16 72,696.00 67 31201517-ta-p01 Tape, Packaging, 48 Mm Roll 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 22.36 0.00 68 31201512-ta-t01 Tape, Transparent, 24mm Roll 0 0 30 30 530.40 0 0 30 30 530.40 0 0 30 30 530.40 0 0 30 30 530.40 120 17.68 2,121.60 69 31201512-ta-t02 Tape, Transparent, 48 Mm Roll 0 0 30 30 677.10 0 0 30 30 677.10 0 0 30 30 677.10 0 0 30 30 677.10 120 22.57 2,708.40 70 31151507-tw-p01 Twine, Plastic Roll 0 0 10 10 666.20 0 0 0 0 0.00 0 0 10 10 666.20 0 0 0 0 0.00 20 66.62 1,332.40 Measuring And Observing And Testing Equipment 71 41111604-ru-p02 Ruler, Plastic, 450mm Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 19.93 0.00 Office Equipment And Accessories And Supplies 72 44121612-bl-h01 Blade, For General Purpose Cutter/utility Knife Tube 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 16.37 0.00 73 44101602-pb-m01 Binding And Punching Machine Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 9,534.72 0.00 74 44122037-rb-p10 Binding Ring/comb, Plastic, 32 Mm Bundle 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 259.89 0.00 75 44101807-ca-c01 Calculator, Compact Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 235.77 0.00 76 44121710-ch-w01 Chalk, White Enamel Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 32.97 0.00 77 44122105-bf-c01 Clip, Backfold, 19mm Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 9.36 0.00 78 44122105-bf-c02 Clip, Backfold, 25mm Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 15.60 0.00 79 44122105-bf-c03 Clip, Backfold, 32mm Box 12 12 12 36 1,198.08 12 12 12 36 1,198.08 12 12 12 36 1,198.08 12 12 12 36 1,198.08 144 33.28 4,792.32 80 44122105-bf-c04 Clip, Backfold, 50mm Box 12 12 12 36 2,171.52 12 12 12 36 2,171.52 12 12 12 36 2,171.52 12 12 12 36 2,171.52 144 60.32 8,686.08 81 44121801-ct-r02 Correction Tape Piece 40 40 40 120 1,620.00 40 40 40 120 1,620.00 40 40 40 120 1,620.00 40 40 40 120 1,620.00 480 13.50 6,480.00 82 44121612-cu-h01 Cutter/utility Knife, For General Purpose Piece 0 0 5 5 158.60 0 0 5 5 158.60 0 0 5 5 158.60 0 0 5 5 158.60 20 31.72 634.40 83 44111515-df-b01 Data File Box Piece 0 0 10 10 1,458.90 0 0 10 10 1,458.90 0 0 10 10 1,458.90 0 0 10 10 1,458.90 40 145.89 5,835.60 84 44122011-df-f01 Data Folder Piece 50 50 50 150 12,451.50 50 50 50 150 12,451.50 50 50 50 150 12,451.50 50 50 50 150 12,451.50 600 83.01 49,806.00 85 44103202-ds-m01 Dater Stamp Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 434.95 0.00 86 44121506-en-d01 Envelope, Documentary, A4 Box 0 0 0 0 0.00 0 0 5 5 4,149.60 0 0 5 5 4,149.60 0 0 5 5 4,149.60 15 829.92 12,448.80 87 44121506-en-d02 Envelope, Documentary, Legal, Box 5 0 5 10 10,575.80 5 0 5 10 10,575.80 5 0 5 10 10,575.80 5 0 5 10 10,575.80 40 1,057.58 42,303.20 88 44121506-en-x01 Envelope, Expanding, Kraft Box 5 0 5 10 9,399.50 5 0 5 10 9,399.50 5 0 5 10 9,399.50 5 0 5 10 9,399.50 40 939.95 37,598.00 89 44121506-en-x02 Envelope, Expanding, Plastic Piece 0 0 0 0 0.00 0 0 10 10 304.90 0 0 10 10 304.90 0 0 10 10 304.90 30 30.49 914.70 90 44121506-en-m02 Envelope, Mailing Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 432.52 0.00 91 44121504-en-w02 Envelope, Mailing, With Window Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 512.72 0.00 92 44111912-er-b01 Eraser, Felt, For Blackboard/whiteboard Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 14.48 0.00 93 44122118-fa-p01 Fastener Box 30 30 30 90 8,517.60 30 30 30 90 8,517.60 30 30 30 90 8,517.60 30 30 30 90 8,517.60 360 94.64 34,070.40 94 44111515-fo-x01 File Organizer, Expanding, Plastic, Legal Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 90.20 0.00 95 44122018-ft-d01 File Tab Divider, A4 Set 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 11.13 0.00 96 44122018-ft-d02 File Tab Divider, Legal Set 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 14.23 0.00 97 44122011-fo-f01 Folder, Fancy With Slide, A4 Bundle 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 270.40 0.00 98 44122011-fo-f02 Folder, Fancy With Slide, Legal Bundle 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 291.20 0.00 99 44122011-fo-l01 Folder, L-type, A4 Pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 200.28 0.00 100 44122011-fo-l02 Folder, L-type, Legal Pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 249.08 0.00 101 44122027-fo-p01 Folder, Pressboard Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 952.64 0.00 102 44122011-fo-t01 Folder With Tab, A4 Pack 0 0 5 5 1,898.00 0 0 5 5 1,898.00 0 0 5 5 1,898.00 0 0 5 5 1,898.00 20 379.60 7,592.00 103 44122011-fo-t02 Folder With Tab, Legal Pack 0 0 10 10 4,139.20 0 0 10 10 4,139.20 0 0 10 10 4,139.20 0 0 10 10 4,139.20 40 413.92 16,556.80 104 44122008-it-t01 Index Tab Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 67.60 0.00 105 44121716-ma-f01 Marker, Flourescent Set 20 20 20 60 1,866.60 20 20 20 60 1,866.60 20 20 20 60 1,866.60 20 20 20 60 1,866.60 240 31.11 7,466.40 106 44121708-mp-b01 Marker, Permanent, Black Piece 60 60 60 180 1,488.60 60 60 60 180 1,488.60 60 60 60 180 1,488.60 60 60 60 180 1,488.60 720 8.27 5,954.40 107 44121708-mp-b02 Marker, Permanent, Blue Piece 60 60 60 180 1,488.60 60 60 60 180 1,488.60 60 60 60 180 1,488.60 60 60 60 180 1,488.60 720 8.27 5,954.40 108 44121708-mp-b03 Marker, Permanent, Red Piece 0 0 12 12 99.24 0 0 12 12 99.24 0 0 12 12 99.24 0 0 12 12 99.24 48 8.27 396.96 109 44121708-mw-b01 Marker, Whiteboard, Black Piece 15 15 15 45 434.25 15 15 15 45 434.25 15 15 15 45 434.25 15 15 15 45 434.25 180 9.65 1,737.00 110 44121708-mw-b02 Marker, Whiteboard, Blue Piece 15 15 15 45 434.25 15 15 15 45 434.25 15 15 15 45 434.25 15 15 15 45 434.25 180 9.65 1,737.00 Item & Specifications Unit Of Measure Monthly Quantity Requirement Total Quantity For The Year Price Total Amount For The Year Jan Feb Mar Q1 Q1 Amount April May June Q2 Q2 Amount July Aug Sept Q3 Q3 Amount Oct Nov Dec Q4 Q4 Amount 111 44121708-mw-b03 Marker, Whiteboard, Red Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 9.65 0.00 112 44122104-pc-g01 Paper Clip, Vinly/plastic Coated, 33mm Box 15 15 15 45 396.90 15 15 15 45 396.90 15 15 15 45 396.90 15 15 15 45 396.90 180 8.82 1,587.60 113 44122104-pc-j02 Paper Clip, Vinly/plastic Coated, Jumbo, 50mm Box 15 15 15 45 875.70 15 15 15 45 875.70 15 15 15 45 875.70 15 15 15 45 875.70 180 19.46 3,502.80 114 44101603-ps-m02 Paper Shredder Unit 0 0 1 1 18,718.96 0 0 0 0 0.00 0 0 1 1 18,718.96 0 0 0 0 0.00 2 18,718.96 37,437.92 115 44101601-pt-m02 Paper Trimmer/cutting Machine Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 9,297.60 0.00 116 44121706-pe-l01 Pencil, Lead/graphite, With Eraser Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 44.71 0.00 117 44121619-ps-m01 Pencil Sharpener Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 236.08 0.00 118 44101602-pu-p01 Puncher, Paper, Heavy Duty Piece 5 5 5 15 2,308.80 5 5 5 15 2,308.80 5 5 5 15 2,308.80 5 5 5 15 2,308.80 60 153.92 9,235.20 119 44122101-ru-b01 Rubber Band No. 18 Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 135.20 0.00 120 44121905-sp-f01 Stamp Pad, Felt Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 39.92 0.00 121 44121618-ss-s01 Scissors, Symmetrical/asymmetrical Pair 5 5 5 15 982.80 5 5 5 15 982.80 5 5 5 15 982.80 5 5 5 15 982.80 60 65.52 3,931.20 122 44121615-st-s01 Stapler, Standard Type Piece 0 0 10 10 1,976.00 0 0 10 10 1,976.00 0 0 10 10 1,976.00 0 0 10 10 1,976.00 40 197.60 7,904.00 123 44121615-st-b01 Stapler, Heavy Duty (binder) Unit 0 0 1 1 693.15 0 0 0 0 0.00 0 0 1 1 693.15 0 0 0 0 0.00 2 693.15 1,386.30 124 44121613-sr-p02 Staple Remover, Plier-type Piece 15 15 15 45 2,092.95 15 15 15 45 2,092.95 15 15 15 45 2,092.95 15 15 15 45 2,092.95 180 46.51 8,371.80 125 44121605-td-t01 Tape Dispenser, Table Top Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 77.58 0.00 Paper Materials And Products 126 14111525-ca-a01 Cartolina, Assorted Colors Pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 83.72 0.00 127 14111506-cf-l11 Computer Continuous Form, 1 Ply, 280mm X 241mm Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 945.36 0.00 128 14111506-cf-l12 Computer Continuous Form, 1 Ply, 280mm X 378mm Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,973.92 0.00 129 14111514-np-s02 Notepad, Stick-on, 50mm X 76mm Pad 30 30 30 90 3,335.40 30 30 30 90 3,335.40 30 30 30 90 3,335.40 30 30 30 90 3,335.40 360 37.06 13,341.60 130 14111514-np-s04 Notepad, Stick-on, 76mm X 100mm Pad 30 30 30 90 5,335.20 30 30 30 90 5,335.20 30 30 30 90 5,335.20 30 30 30 90 5,335.20 360 59.28 21,340.80 131 14111514-np-s03 Notepad, Stick-on, 76mm X 76mm Pad 30 30 30 90 4,680.00 30 30 30 90 4,680.00 30 30 30 90 4,680.00 30 30 30 90 4,680.00 360 52.00 18,720.00 132 14111514-nb-s02 Steno Notebook Piece 0 0 20 20 280.80 0 0 20 20 280.80 0 0 20 20 280.80 0 0 20 20 280.80 80 14.04 1,123.20 133 14111507-pp-m01 Paper, Multicopy A4 Ream 50 50 50 150 32,070.00 50 50 50 150 32,070.00 50 50 50 150 32,070.00 50 50 50 150 32,070.00 600 213.80 128,280.00 134 14111507-pp-m02 Paper, Multicopy Legal Ream 10 10 10 30 6,988.80 10 10 10 30 6,988.80 10 10 10 30 6,988.80 10 10 10 30 6,988.80 120 232.96 27,955.20 135 14111507-pp-c01 Paper, Multipurpose A4 Ream 50 50 50 150 20,661.00 50 50 50 150 20,661.00 50 50 50 150 20,661.00 50 50 50 150 20,661.00 600 137.74 82,644.00 136 14111507-pp-c02 Paper, Multipurpose Legal Ream 10 10 10 30 4,767.30 10 10 10 30 4,767.30 10 10 10 30 4,767.30 10 10 10 30 4,767.30 120 158.91 19,069.20 137 14111531-pp-r01 Pad Paper, Ruled Pad 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 34.82 0.00 138 14111503-pa-p01 Paper, Parchment Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 154.21 0.00 139 14111531-re-b01 Record Book, 300 Pages Book 10 10 10 30 2,751.00 10 10 10 30 2,751.00 10 10 10 30 2,751.00 10 10 10 30 2,751.00 120 91.70 11,004.00 140 14111531-re-b02 Record Book, 500 Pages Book 20 20 20 60 7,473.60 20 20 20 60 7,473.60 20 20 20 60 7,473.60 20 20 20 60 7,473.60 240 124.56 29,894.40 141 14111704-tt-p04 Tissue, Interfolded Paper Towel Pack 100 100 100 300 10,140.00 100 100 100 300 10,140.00 100 100 100 300 10,140.00 100 100 100 300 10,140.00 1200 33.80 40,560.00 142 14111704-tt-p02 Toilet Tissue Paper, 2 Ply Pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 99.84 0.00 Perfumes Or Colognes Or Fragrances 143 53131626-hs-s01 Hand Sanitizer Bottle 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 85.08 0.00 Pesticides Or Pest Repellents 144 10191509-in-a01 Insecticide Can 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 139.36 0.00 Printed Publications 145 55101524-ra-h01 Handbook On Philippine Government Procurement (ra 9184 And Its Irr) Book 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 37.21 0.00 Printer Or Facsimile Or Photocopier Supplies (consumables) 1 44103109-br-d05 Drum Cartridge, Brother Dr-3455, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 6,947.20 0.00 2 44103105-ca-c04 Ink Cartridge, Canon Cl-741, Colored Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,126.32 0.00 3 44103105-ca-c02 Ink Cartridge, Canon Cl-811, Colored Cart 10 10 10 30 35,349.60 10 10 10 30 35,349.60 10 10 10 30 35,349.60 10 10 10 30 35,349.60 120 1,178.32 141,398.40 4 44103105-ca-b04 Ink Cartridge, Canon Pg-740, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 861.12 0.00 5 44103105-ca-b02 Ink Cartridge, Canon Pg-810, Black Cart 20 20 20 60 53,539.20 20 20 20 60 53,539.20 20 20 20 60 53,539.20 20 20 20 60 53,539.20 240 892.32 214,156.80 6 44103105-ep-b17 Ink Cartridge, Epson C13t664100 (t6641), Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 231.90 0.00 7 44103105-ep-c17 Ink Cartridge, Epson C13t664200 (t6642), Cyan Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 242.20 0.00 8 44103105-ep-m17 Ink Cartridge, Epson C13t664300 (t6643), Magenta Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 242.20 0.00 9 44103105-ep-y17 Ink Cartridge, Epson C13t664400 (t6644), Yellow Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 242.20 0.00 Item & Specifications Unit Of Measure Monthly Quantity Requirement Total Quantity For The Year Price Total Amount For The Year Jan Feb Mar Q1 Q1 Amount April May June Q2 Q2 Amount July Aug Sept Q3 Q3 Amount Oct Nov Dec Q4 Q4 Amount 10 44103105-hp-b40 Ink Cartridge, Hp C2p04aa (hp62), Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 852.80 0.00 11 44103105-hp-t40 Ink Cartridge, Hp C2p06aa (hp62), Tri-color Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,048.32 0.00 12 44103105-hp-b09 Ink Cartridge, Hp C9351aa (hp21), Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 910.00 0.00 13 44103105-hp-t10 Ink Cartridge, Hp C9352aa (hp22), Tri-color Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,053.52 0.00 14 44103105-hp-b17 Ink Cartridge, Hp Cc640wa (hp60), Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 880.88 0.00 15 44103105-hp-t17 Ink Cartridge, Hp Cc643wa (hp60), Tri-color Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,047.28 0.00 16 44103105-hx-c40 Ink Cartridge, Hp Cd972aa (hp920xl), Cyan Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 823.68 0.00 17 44103105-hx-m40 Ink Cartridge, Hp Cd973aa (hp920xl), Magenta Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 823.68 0.00 18 44103105-hx-y40 Ink Cartridge, Hp Cd974aa (hp920xl), Yellow Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 823.68 0.00 19 44103105-hx-b40 Ink Cartridge, Hp Cd975aa (hp920xl), Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,541.28 0.00 20 44103105-hp-b20 Ink Cartridge, Hp Ch561wa (hp61), Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 865.28 0.00 21 44103105-hp-t20 Ink Cartridge, Hp Ch562wa (hp61), Tri-color Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,066.00 0.00 22 44103105-hx-b43 Ink Cartridge, Hp Cn045aa (hp950xl), Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,970.80 0.00 23 44103105-hx-c43 Ink Cartridge, Hp Cn046aa (hp951xl), Cyan Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,517.36 0.00 24 44103105-hx-m43 Ink Cartridge, Hp Cn047aa (hp951xl), Magenta Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,517.36 0.00 25 44103105-hx-y43 Ink Cartridge, Hp Cn048aa (hp951xl), Yellow Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,517.36 0.00 26 44103105-hp-b36 Ink Cartridge, Hp Cn692aa (hp704), Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 419.12 0.00 27 44103105-hp-t36 Ink Cartridge, Hp Cn693aa (hp704), Tri-color Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 419.12 0.00 28 44103105-hp-b33 Ink Cartridge, Hp Cz107aa (hp678), Black Cart 5 5 5 15 6,068.40 5 5 5 15 6,068.40 5 5 5 15 6,068.40 5 5 5 15 6,068.40 60 404.56 24,273.60 29 44103105-hp-t33 Ink Cartridge, Hp Cz108aa (hp678), Tri-color Cart 5 5 5 15 6,068.40 5 5 5 15 6,068.40 5 5 5 15 6,068.40 5 5 5 15 6,068.40 60 404.56 24,273.60 30 44103105-hp-t43 Ink Cartridge, Hp F6v26aa (hp680), Tri-color Cart 20 20 20 60 25,459.20 20 20 20 60 25,459.20 20 20 20 60 25,459.20 20 20 20 60 25,459.20 240 424.32 101,836.80 31 44103105-hp-b43 Ink Cartridge, Hp F6v27aa (hp680), Black Cart 25 25 25 75 31,824.00 25 25 25 75 31,824.00 25 25 25 75 31,824.00 25 25 25 75 31,824.00 300 424.32 127,296.00 32 44103105-hp-c50 Ink Cartridge, Hp L0s51aa (hp955), Cyan Original Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 982.80 0.00 33 44103105-hp-m50 Ink Cartridge, Hp L0s54aa (hp955), Magenta Original Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 982.80 0.00 34 44103105-hp-y50 Ink Cartridge, Hp L0s57aa (hp955), Yellow Original Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 982.80 0.00 35 44103105-hp-b50 Ink Cartridge, Hp L0s60aa (hp955), Black Original Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,294.80 0.00 36 44103105-hx-c48 Ink Cartridge, Hp L0s63aa (hp955xl), Cyan Original Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,339.52 0.00 37 44103105-hx-m48 Ink Cartridge, Hp L0s66aa (hp955xl), Magenta Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,339.52 0.00 38 44103105-hx-y48 Ink Cartridge, Hp L0s69aa (hp955xl), Yellow Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,339.52 0.00 39 44103105-hx-b48 Ink Cartridge, Hp L0s72aa (hp955xl), Black Original Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,817.92 0.00 40 44103105-hp-c51 Ink Cartridge, Hp T6l89aa (hp905), Cyan Original Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 468.00 0.00 41 44103105-hp-m51 Ink Cartridge, Hp T6l93aa (hp905), Magenta Original Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 468.00 0.00 42 44103105-hp-y51 Ink Cartridge, Hp T6l97aa (hp905), Yellow Original Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 468.00 0.00 43 44103105-hp-b51 Ink Cartridge, Hp T6m01aa (hp905), Black Original Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 774.80 0.00 44 44103112-ep-r05 Ribbon Cartridge, Epson C13s015516 (#8750), Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 77.43 0.00 45 44103112-ep-r13 Ribbon Cartridge, Epson C13s015632, Black Cart 4 4 4 12 935.28 4 4 4 12 935.28 4 4 4 12 935.28 4 4 4 12 935.28 48 77.94 3,741.12 46 44103112-ep-r07 Ribbon Cartridge, Epson C13s015531 (s015086) Cart 1 1 1 3 2,455.44 1 1 1 3 2,455.44 1 1 1 3 2,455.44 1 1 1 3 2,455.44 12 818.48 9,821.76 47 44103103-br-b09 Toner Cartridge, Brother Tn-3320, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 3,567.20 0.00 48 44103103-br-b11 Toner Cartridge, Brother Tn-3350, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 5,002.40 0.00 49 44103103-br-b15 Toner Cartridge, Brother Tn-3478, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 5,575.44 0.00 50 44103103-br-b16 Toner Cartridge, Brother Tn-456 Black, High Yield Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 4,564.56 0.00 51 44103103-br-c03 Toner Cartridge, Brother Tn-456 Cyan, High Yield Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 7,716.80 0.00 52 44103103-br-m03 Toner Cartridge, Brother Tn-456 Magenta, High Yield Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 7,716.80 0.00 53 44103103-br-y03 Toner Cartridge, Brother Tn-456 Yellow, High Yield Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 7,716.80 0.00 54 44103103-ca-b00 Toner Cartridge, Canon Crg-324 Ii Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 13,399.36 0.00 55 44103103-hp-b12 Toner Cartridge, Hp Cb435a, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 3,439.28 0.00 56 44103103-hp-b18 Toner Cartridge, Hp Ce255a, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 7,705.36 0.00 57 44103103-hp-b21 Toner Cartridge, Hp Ce278a, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 4,152.72 0.00 58 44103103-hp-b22 Toner Cartridge, Hp Ce285a (hp85a), Black Cart 10 10 0 20 71,968.00 10 10 0 20 71,968.00 10 10 0 20 71,968.00 10 10 0 20 71,968.00 80 3,598.40 287,872.00 Item & Specifications Unit Of Measure Monthly Quantity Requirement Total Quantity For The Year Price Total Amount For The Year Jan Feb Mar Q1 Q1 Amount April May June Q2 Q2 Amount July Aug Sept Q3 Q3 Amount Oct Nov Dec Q4 Q4 Amount 59 44103103-hp-b23 Toner Cartridge, Hp Ce310a, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 2,608.32 0.00 60 44103103-hp-c23 Toner Cartridge, Hp Ce311a, Cyan Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 2,897.44 0.00 61 44103103-hp-y23 Toner Cartridge, Hp Ce312a, Yellow Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 2,897.44 0.00 62 44103103-hp-m23 Toner Cartridge, Hp Ce313a, Magenta Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 2,897.44 0.00 63 44103103-hp-b28 Toner Cartridge, Hp Ce505a, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 4,495.92 0.00 64 44103103-hp-b52 Toner Cartridge, Hp Cf217a (hp17a), Black Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 3,194.88 0.00 65 44103103-hp-b53 Toner Cartridge, Hp Cf226a (hp26a), Black Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 5,822.96 0.00 66 44103103-hp-b56 Toner Cartridge, Hp Cf281a (hp81a), Black Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 8,658.00 0.00 67 44103103-hp-b57 Toner Cartridge, Hp Cf283a (hp83a), Laserjet Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 3,367.52 0.00 68 44103103-hp-b58 Toner Cartridge, Hp Cf287a (hp87), Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 10,908.56 0.00 69 44103103-hp-b60 Toner Cartridge, Hp Cf350a, Black Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 2,856.88 0.00 70 44103103-hp-c60 Toner Cartridge, Hp Cf351a, Cyan Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 2,943.20 0.00 71 44103103-hp-y60 Toner Cartridge, Hp Cf352a, Yellow Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 2,943.20 0.00 72 44103103-hp-m60 Toner Cartridge, Hp Cf353a, Magenta Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 2,943.20 0.00 73 44103103-hp-b61 Toner Cartridge, Hp Cf360a (hp508a), Black Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 7,803.12 0.00 74 44103103-hp-c61 Toner Cartridge, Hp Cf361a (hp508a), Cyan Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 9,783.28 0.00 75 44103103-hp-y61 Toner Cartridge, Hp Cf362a (hp508a), Yellow Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 9,783.28 0.00 76 44103103-hp-m61 Toner Cartridge, Hp Cf363a (hp508a), Magenta Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 9,783.28 0.00 77 44103103-hp-b62 Toner Cartridge, Hp Cf400a (hp201a), Black Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 3,439.28 0.00 78 44103103-hp-c62 Toner Cartridge, Hp Cf401a (hp201a), Cyan Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 4,063.28 0.00 79 44103103-hp-y62 Toner Cartridge, Hp Cf402a (hp201a), Yellow Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 4,063.28 0.00 80 44103103-hp-m62 Toner Cartridge, Hp Cf403a (hp201a), Magenta Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 4,063.28 0.00 81 44103103-hp-b63 Toner Cartridge, Hp Cf410a (hp410a), Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 4,328.48 0.00 82 44103103-hp-c63 Toner Cartridge, Hp Cf411a (hp410a), Cyan Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 5,592.08 0.00 83 44103103-hp-y63 Toner Cartridge, Hp Cf412a (hp410a), Yellow Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 5,592.08 0.00 84 44103103-hp-m63 Toner Cartridge, Hp Cf413a (hp410a), Magenta Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 5,592.08 0.00 85 44103103-hp-b34 Toner Cartridge, Hp Q2612a, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 4,155.84 0.00 86 44103103-hp-b48 Toner Cartridge, Hp Q7553a, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 4,680.00 0.00 Software 1 43231513-sft-001 Business Function Specific Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 2 43231602-sft-002 Finance Accounting And Enterprise Resource Planning Erp Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 3 43232004-sft-003 Computer Game Or Entertainment Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 4 43232107-sft-004 Content Authoring And Editing Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 5 43232202-sft-005 Content Management Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 6 43232304-sft-006 Data Management And Query Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 7 43232402-sft-007 Development Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 8 43232505-sft-008 Educational Or Reference Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 9 43232603-sft-009 Industry Specific Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 10 43233501-sft-016 Information Exchange Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 11 43232701-sft-010 Network Applications Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 12 43232802-sft-011 Network Management Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 13 43232905-sft-012 Networking Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 14 43233004-sft-013 Operating Environment Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 15 43233205-sft-014 Security And Protection Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 16 43233405-sft-015 Utility And Device Driver Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 Part Ii. Other Items Not Available At Ps-dbm But Are Regularly Purchased From Other Sources (note: Please Indicate Price Of Items) 1 80141505-ts-001 Ballpen Piece 100 100 100 300 3,900.00 100 100 100 300 3,900.00 100 100 100 300 3,900.00 100 100 100 300 3,900.00 1200 13.00 15,600.00 2 80141505-ts-002 Multifunction Printer Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 3 80141505-ts-003 Laminating Film Pack 5 5 5 15 6,000.00 5 5 5 15 6,000.00 5 5 5 15 6,000.00 5 5 5 15 6,000.00 60 400.00 24,000.00 Item & Specifications Unit Of Measure Monthly Quantity Requirement Total Quantity For The Year Price Total Amount For The Year Jan Feb Mar Q1 Q1 Amount April May June Q2 Q2 Amount July Aug Sept Q3 Q3 Amount Oct Nov Dec Q4 Q4 Amount 4 80141505-ts-004 Sticker Paper Pack 0 0 10 10 600.00 0 0 10 10 600.00 0 0 10 10 600.00 0 0 10 10 600.00 40 60.00 2,400.00 5 80141505-ts-005 Double Sided Tape Roll 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 6 80141505-ts-006 Photo Paper Pack 0 0 10 10 1,900.00 0 0 10 10 1,900.00 0 0 10 10 1,900.00 0 0 10 10 1,900.00 40 190.00 7,600.00 7 80141505-ts-007 Bleaching Solution Bottle 0 0 0 0 0.00 0 0 50 50 12,000.00 0 0 0 0 0.00 0 0 50 50 12,000.00 100 240.00 24,000.00 8 80141505-ts-008 Certificate Frame Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 9 80141505-ts-009 Certificate Holder Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 10 80141505-ts-010 Uninterruptible Power Supply Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 11 80141505-ts-011 Air Conditioning Unit Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 12 80141505-ts-012 Smart Television Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 13 80141505-ts-013 White Board Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 14 80141505-ts-014 Microphone Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 15 80141505-ts-015 Medal Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 16 80141505-ts-016 Dishwashing Liquid Bottle 10 10 10 30 9,900.00 10 10 10 30 9,900.00 10 10 10 30 9,900.00 10 10 10 30 9,900.00 120 330.00 39,600.00 17 80141505-ts-017 Plastic Fastener Box 10 10 10 30 1,410.00 10 10 10 30 1,410.00 10 10 10 30 1,410.00 10 10 10 30 1,410.00 120 47.00 5,640.00 18 80141505-ts-018 Steel Filing Cabinet Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 19 80141505-ts-019 Vellum Board Paper Pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 20 80141505-ts-020 Extension Cord Piece 0 0 0 0 0.00 5 5 5 15 18,000.00 0 0 0 0 0.00 5 5 5 15 18,000.00 30 1,200.00 36,000.00 21 80141505-ts-021 Paint Gallon 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 22 80141505-ts-022 Colored Paper Pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 23 80141505-ts-023 Bond Paper Ream 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 24 80141505-ts-024 Push Pin Pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 25 80141505-ts-025 Door Mat Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 26 80141505-ts-026 Glue Stick (paste) Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 27 80141505-ts-027 Glue Stick (for Glue Gun) Pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 28 80141505-ts-028 Deodorant Cake Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 29 80141505-ts-029 Disposable Gloves Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 30 80141505-ts-030 Office Chair Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 31 80141505-ts-031 Manila Paper Pack 0 0 10 10 800.00 0 0 0 0 0.00 0 0 10 10 800.00 0 0 0 0 0.00 20 80.00 1,600.00 32 80141505-ts-032 Automotive Batteries Piece 0 1 0 1 7,500.00 0 1 0 1 7,500.00 0 1 0 1 7,500.00 0 1 0 1 7,500.00 4 7,500.00 30,000.00 33 80141505-ts-033 Padlock Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 34 80141505-ts-034 Mobile Phone Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 35 80141505-ts-035 Compact Disc Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 36 80141505-ts-036 Amplifier Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 37 80141505-ts-037 Storage Box Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 38 80141505-ts-038 Plastic Envelope Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 39 80141505-ts-039 Document Scanner Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 40 80141505-ts-040 Water Dispenser Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 41 80141505-ts-041 Paracetamol Pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 42 80141505-ts-042 Glue Gun Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 43 80141505-ts-043 Inkjet Printer Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 44 80141505-ts-044 Speakers Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 45 80141505-ts-045 Povidone Iodine Bottle 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 46 80141505-ts-046 Keyboard Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 47 80141505-ts-047 Dslr Camera Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 48 80141505-ts-048 Steel Rack Set 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 49 80141505-ts-049 Laminating Machine Unit 0 0 1 1 5,000.00 0 0 0 0 0.00 0 0 1 1 5,000.00 0 0 0 0 0.00 2 5,000.00 10,000.00 50 80141505-ts-050 Fuel Filters Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 51 80141505-ts-051 Airline Tickets (domestic) Ticket 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 52 80141505-ts-052 Airline Tickets (international) Ticket 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 Item & Specifications Unit Of Measure Monthly Quantity Requirement Total Quantity For The Year Price Total Amount For The Year Jan Feb Mar Q1 Q1 Amount April May June Q2 Q2 Amount July Aug Sept Q3 Q3 Amount Oct Nov Dec Q4 Q4 Amount 53 80141505-ts-053 Car (sedan Or Hatchback) Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 46 80141505-ts-054 Multi-purpose Vehicle (mpv) Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 47 80141505-ts-055 Sports Utility Vehicle (suv) Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 48 80141505-ts-056 Passenger Van Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 49 80141505-ts-057 Van Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 50 80141505-ts-058 Tri-wheel Vehicle Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 51 80141505-ts-059 Pick-up Truck Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 52 80141505-ts-060 All-terrain Vehicle (atv) Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 53 80141505-ts-061 Assembled Owner-type Jeep Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 50 80141505-ts-062 Assembled Passenger Jeepney-type Vehicle Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 51 80141505-ts-063 Motorcycle Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 52 80141505-ts-064 Bus Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 53 80141505-ts-065 Mini Bus Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 A. Total ₱ 2,576,442.32 B. Additional Provision For Inflation (10% Of Total) ₱ 257,644.23 C. Additional Provision For Transport And Freight Cost (if Applicable) ₱ - D. Grand Total (a + B+ C) ₱ 2,834,086.55 E. Approved Budget By The Agency Head In Figures And Words: We Hereby Warrant That The Total Amount Reflected In This Annual Procurement Plan To Procure The Listed Common-use Supplies, Materials, And Equipment Has Been Included In Or Is Within Our Approved Budget For The Year. Prepared By: Certified Funds Available / Certified Appropriate Funds Available: Approved By: Property/supply Officer Date Prepared: Accountant / Budget Officer Head Of Office/agency