Fire Extinguisher Tenders

Details: Description I. Project Description The Project Involves The Design And Build Of A 3 Mld Water Treatment Facility, Inclusive Of A 3 Mld Water Treatment Plant (wtp), Raw Water Abstraction Facility, Raw Water Pipeline, Raw Water Impounding Lagoon, Product Pumping Station, 3 Phase Power Transmission Line And Product Water Transmission And Distribution Pipelines To Barangays Poblacion Norte And Poblacion Sur. It Also Includes One (1) Month Proving Period With Performance Guarantees On Specific Usages Of Power And Chemicals For The Production Of Potable Water That Meets The Philippine National Standards For Drinking Water. Ii. Conceptual Design The Project Concept Is To Construct A 3 Mld Water Treatment Facility Using Socon River As Raw Water Source. The Raw Water Will Undergo Series Of Processes To Remove Sediments, Microbes And Other Impurities To Ensure That The Water Reaching To The Consumers Complies With The Quality Set Forth In The Philippine National Standards For Drinking Water, Pnsdw. The Product Will Be Distributed To Barangays Poblacion Norte And Poblacion Sur. Iii. Proposed Project Components: 1. Raw Water Abstraction (intake) Facility 2. Raw Water Transmission Line 3. Impounding (raw Water) Lagoon 4. Lagoon Pumping Station 5. 3 Mld Water Treatment Plant 6. Residual Management Facility (sludge Lagoon) 7. Product Water Pumping Station 8. Power Supply 9. Product Water Transmission Line 10. Product Water Distribution Lines, Valves, Fittings And Other Appurtenances 11. Site Development • General Earthworks • Fence Below Are The Coordinates Of The Proposed Locations Of The Facilities: Table 1. Location Of The Proposed Facility Facilities Location Proposed Location Of The Facility 9°49’40” N, 124°12’43” E Iv. General Map Showing The Location Of The Proposed Water Treatment Facility V. Conceptual Design Of A 3 Mld Water Treatment Facility Vi. Approved Budget Of Contract The Total Capital Expenditure (capex) Requirement For This Project Is Php 115,000,000.00. The Project Is Financed Through A Term Loan Agreement With The Development Bank Of The Philippines. Progress Payments To The Contractor Shall Be Governed By The Terms And Conditions Set Forth In The Omnibus Term Loan Agreement And The Deed Of Undertaking, Duly Executed Between The Development Bank Of The Philippines And The Municipality Of Carmen, Bohol. Furthermore, These Payments Shall Adhere To The Pertinent Provisions Of The Implementing Rules And Regulations Of Republic Act No. 9184, The Relevant Coa Rules And Regulations, And Any Other Applicable Laws. These Terms And Conditions Are Hereby Formally Communicated To All Prospective Bidders Through This Provision. Table Below Summarizes The Component Cost Of The Capex. Capex Summary Component Cost, Php Site Development And Fencing Raw Water Abstraction Facility Raw Water Transmission Pipeline Raw Water Impounding Lagooon 3 Mld Water Treatment Plant Residual Management Facility Product Pumping Station Power Supply Product Water Transmission Pipeline Product Water Distribution Lines, Valves, Fittings And Other Appurtenances Engineering & Design Commissioning & Proving Period Temporary Facility Total Project Cost Php 115,000,000.00 Vii. Proposed Design & Construction Schedule The Project Must Be Completed Within One (1) Year From Receipt Of Notice To Proceed. Viii. Contractor’s Track Record And Performance Guarantee The Contractor Must Show Proof That It Has Previously Installed A Water Treatment Plant (“wtp”) With A Proven Capacity Of No Less Than 3.0 Mld Capable Of Treating River Water At Turbidity Level Up To 5,000 Ntu. The Said Wtp Should Demonstrate A Low Energy Consumption Not Exceeding 0.15 Kwh/m3 Within The Wtp Battery Limit. The Contractor Must Be Able To Successfully Demonstrate During The 7-day Performance Test That The Wtp Has Continuously Operated At A Production Rate Of No Less Than 3.0 Mld, Energy Consumption Not Exceeding 0.15 Kwh/m3 And Product Water Quality That Meets The Specifications Of The Philippine National Standard For Drinking Water. The Contractor Must Incorporate In The Design Of Its Wtp A Feature That Will Allow 100% Water Recovery And Zero Effluent Discharge. Ix. General Scope Of Works Of The Contractor The Contractor Is Required To Perform The Following Scope Of Works: 1. Review Of Existing Information Review The Basic Design Parameters And Detailed Scope Of Works. The Contractor Shall Ensure That It Has First-hand Information On The Site Development Plan, Construction Data, Geo-hazard Maps, Elevation And Other Gis Maps And Other Documents That Are Readily Available From The Project Owner. Such Will Be Used To Define Project Design Criteria And Serve As Basis For Any Changed Conditions And Establish Project Cost Estimates. Should Any Of These Data And Other Pertinent Data Be Unavailable, The Contractor Shall Carry Out The Needed Testing/investigation To Complete The Needed Design Data. 2. Field Survey And Site Inspection The Contractor Shall Conduct The Appropriate Site Survey Including Staking, Establishing Of Horizontal And Vertical Control Points, Benchmarks, Traverse And Profile Survey, And Stream Flow. 3. The Contractor Shall Have Inspected The Site And Its Surroundings And Orient Himself With The Following: A. Location And Nature Of Work; B. Climatic Conditions; C. Nature And Condition Of The Terrain; D. Geologic Conditions At The Site; E. Transportation And Communication Facilities; F. Availability Of Construction Materials, Labor, Water Services, Electric And Power Supply; G. Location And Extent Of Aggregate Sources; And H. Other Factors That May Affect The Cost, Duration And Execution Of The Work. 4. Pipeline And Structural Analysis The Contractor Shall Prepare The Necessary Structural Analyses, Calculations And Design Of Structural Members In Accordance With The National Building Code Of The Philippines, National Structural Code Of The Philippines And Other Relevant Codes. The Design Of The Main Structure And Its Appurtenances Shall Take Into Account Prevailing Conditions Of The Area To Attain The Optimum Safety Of The Whole Structure. The Contractor Shall Prepare The Pipeline Design On The Basis Of Data Obtained From Site Investigations And Survey Of The Proposed Water Source, Site For Water Treatment Plant, And The Location Of Pipelines, Materials And Other Investigations Necessary In Standard Engineering Practice To Ensure High Efficiency Of The Proposed Water System. 5. Hydraulic Analysis The Contractor Shall Make A Hydraulic Analysis That Form Part Of The Technical Documents To Be Submitted To Ascertain That The Water System Could Provide The Required Flow And Pressure Based On The Designed Population And Planning Period. At The End Of The Design Stage, The Contractor Is Expected To Produce The Appropriate Design And Construction Plans. 6. Permits And Licenses The Contractor Shall Be Responsible For The Application Of Necessary Permits, Clearances And Licenses From Local And National Agencies Having Jurisdiction Over The Project. No Commencement Of The Project Without First Securing The Said Documents. 7. Construction Works The Contractor Shall Perform The Following Construction Activities But Is Not Limited To The Following: A. Mobilization/demolition The Contractor Shall Mobilize And Bring Out Into Work, All Personnel, Plant And Equipment, In Accordance With His Approved Construction Program, Equipment Moving And Utilization Schedule And Manpower Schedule, From Its Regular Place Of Business To The Site To Undertake The Contract. Mobilization Shall Include The Obtaining And Transporting To Jobsite Of Equipment, Materials, Tools, Personnel, Constructional Plant And All Necessary Items For The Execution And Completion Of The Work And Shall Also Include The Setting Up And Verification Of All Equipment And Instruments Until It Is Rendered Operable. Demobilization Shall Include Dismantlement And Removal From The Site Of The Contractor’s Materials And Equipment And All Temporary Facilities. It Shall Also Include A Clean-up Of The Site After Completion Of The Contract As Well As Transportation From The Site Of The Contractor’s Personnel. B. Site Clearing And Proper Waste Disposal General Site Clearing Operations Include The Removal Of Demolished Materials And Objectionable Matter, Protection And Clearing To Allow For New Construction. The Contractor Is Obliged To Provide Barricades, Coverings, Or Other Types Of Protection Necessary To Prevent Damages. Likewise, He/she Is To Dispose Of Materials, Trash And Debris In A Safe And Acceptable Manner In Accordance With Applicable Laws And Ordinances. Burying And Burning Of Trash And Debris At The Site Will Not Be Permitted. Trash And Debris Shall Be Removed From The Site At Regular Intervals To Prevent These From Accumulating And Ultimately Delaying The Course Of The Work. Site Works B.1. Excavation, Foundations, Anchorage The Design And Quality Of Structural Materials To Be Used Shall Be In Conformity To The Governing Laws And To The Acceptable Engineering Practices. Footings, Foundation Elements And/or Anchorage Systems Shall Be Of The Appropriate Type, Of Adequate Size/s And Capacity In Order To Safely Sustain The Superimposed Loads Under Seismic Forces, Lateral Earth Pressure Or Any Condition Of External Forces That May Affect The Stability Of The Structure. Excavated Soil Shall Be Coordinated With The Lgu-carmen For Proper Disposal. C. Conduct Of Potability Test After Project Completion And Commissioning, The Contractor Should Conduct Water Potability Test With The Presence Of The Representative Of The End-user. X. Specifications & Parameters A. Scope Of Design And Build Of The Water Treatment Facility And Related Works The Necessary Works For The Design And Build Of The Water Treatment Plant Including Raw Water Abstraction Facility And Pipeline, Product Pumping Station, Potable Water Transmission Pipeline, Power Supply, Metering House And Interconnection At The Delivery Points Shall Include But Not Be Limited To The Following: 1. Design And Construct A 3 Mld Raw Water Abstraction Facility And Raw Water Transmission Pipeline. 2. Design And Construct A 30,000 Cubic Meter Raw Water Impounding Lagoon. 3. Design And Construct A Water Treatment Plant (wtp) That Can Treat Raw Water With A Turbidity Of Up To 5,000 Ntu With 100% Water Recovery And Zero Effluent Discharge. 4. Design And Install A Product Pumping System That Will Pump The Potable Water To The Target Areas. 5. Design And Construct The Power Supply System Needed To Run The Water Treatment Facilities Inclusive Of 3-phase Power Transmission Line, Transformers And Standby Generator Set. 6. Design And Install Product Water Transmission Line And Distribution Line For The Target Service Areas. 7. The Product Pumping And Pipe Sizing Must Be Designed That There Will Be At Least 10 Psi During Peak Hours. 8. Conduct Soil Investigation And Topographic Survey Of The Wtp Site. 9. Design And Construct Associated Civil Works Including Site Development For The Water Treatment Facilities, Site Utilities, Water Supply, Sewer And Drainage System. The Civil Works Shall Include But Not Be Limited To Foundation Works, Formworks, Concreting, Painting And Fencing. 10. Design, Supply And Install All Mechanical And Electrical Components Including Lightning Protection System For The Water Treatment Facilities, Instrumentation And Control Equipment And Accessories That May Be Deemed Necessary For The Efficient And Ease Of Operation Of The Water Treatment Facilities. 11. Provide Appropriate Electromagnetic (if Applicable) Flow Metering Devices For Inflow And Outflow Measurements. 12. Design And Construct Support Facilities Such As Chemical Storage & Control Room, Fence, Road Network, Etc. 13. Supervise Commissioning And Performance Testing Of The Wtp For One (1) Month Upon Issuance Of Mechanical Completion. 14. All Other Works Which May Be Reasonably Implied Or Nor Explicitly Described But Are Needed To Have A Complete And Efficiently Functioning Plant Shall Be Implemented/constructed By The Contractor At No Additional Cost To The Procuring Entity. B. Performance Specifications Of The Water Treatment Facilities And Related Works 1. Design Flowrates The Water Treatment Facilities Shall Be Designed For A Capacity Of 3 Mld. 2. Required Treatment Facilities And Performance Efficiency A. The Treatment Plant Shall Produce Treated Water Effluent Conforming To The 2017 Philippine National Standards For Drinking Water (pnsdw) As Shown In Table Below. The Wtp, Intake And Related Facilities Shall Be Designed With Expected Life Of 25 Years. Table 1. 2017 Philippine National Standards For Drinking Water Parameter Unit Analysis Taste Unobjectionable Odor Unobjectionable Color Apparent Tcu 10 True Tcu 5 Turbidity Ntu 5 Aluminum Mg/l 0.20 Chloride Mg/l 250 Copper Mg/l 1.0 Hardness Mg/l 300 As Caco3 Hydrogen Sulfide Mg/l 0.05 Iron Mg/l 1.0 Manganese Mg/l 0.4 Ph 6.5-8.5 Sodium Mg/l 200 Sulfate Mg/l 250 Total Dissolve Solids Mg/l 600 Zinc Mg/l 5 Arsenic Mg/l 0.01 Boron Mg/l 0.5 Cadmium Mg/l 0.003 Lead Mg/l 0.01 Benzene Mg/l 0.01 E. Coli Or Thermo Tolerant (fecal) Coliform Bacteria No./100 Ml Nil B. Design And Operate The Plant Free From Any Discernable Odor And Noise Louder Than 55 Decibels At The Site Boundary. C. The Contractor Must Incorporate In The Design Of Its Wtp A Feature That Will Allow 100% Water Recovery And Zero Effluent Discharge D. The Annual Average Chemical Usage Should Not Exceed Php 1.00/m3 E. The Power Unit Usage Within The Proposed Wtp Battery Limit (excluding Intake And Product Pumping) Should Not Be More Than 0.15 Kwh/m3. F. The Raw Water Pipeline And Product Water Pipelines Must Withstand A Pressure Of At Least 100 Psi. 3. Minimum Design Requirement The Water Treatment Facilities Must Be Designed To Prevent Total Plant Shutdown When Undergoing Pump Maintenance Works. As Such, There Should Be At Least One Duty And One Stand-by Item Of Equipment To Allow The Plant To Operate At Any Given Time With A Full Process Flow Capacity At The Desired Efficiency During Equipment Replacement/repair Or Maintenance Servicing Or Cleaning. Equipment Upon Which The Plant Is Dependent For Full Operation Must Also Be Provided With Standby. A. Design All Plant Structures To Withstand Pressures And Seismic Loading In Accordance With The National Structural Code Of The Philippines. However, For Structural Concrete, The 28-day Compressive Strength Shall Not Be Less Than 21 Mpa. B. The Minimum Design Requirement For All Buildings Shall Be Concrete Foundations And Floors, Concrete Structural Elements, Galvanized Steel Trusses And Roof Frame, Reinforced And Filled Concrete Block Walls With Rendering And Painting, Bonded-color Steel Roofing System, Suspended Ceilings, Tiled Floors For Office Areas, Ceramic Tiling For Showers, Toilets And Similar Areas, Concealed And Under-floor Service Conduits And Pipelines And Air Conditioning For Office Areas. C. Electrical Power Supply And Control System And Requirements I. The Electrical Power Supply And Control System Shall Include But Not Limited To The Main And Branch Circuit Overcurrent Protective Devices, Motor Controllers Including All Protective And Monitoring Relay Systems Required For The Complete Operation Of The Plant And All Necessary Wiring, Conduits And Grounding Systems. Electrical Power And Control System Shall Be Wired So That The Various Items Of Plant Equipment Can Be Operated Either Manual Or Automatic To Achieve The Intended Sequence Of Operation. Process Control Shall Be Situated At The Motor Control Centers (mcc). Ii. Factory Wired Plant Components Shall Be Interconnected So As To Be An Integral Part Of The Plant. Iii. Provide Surge Protection To Prevent Damage To Electric Motors And All Other Electrical And Electronic Components During Fluctuation Of Voltage, During Resumption Of Power Supply After A Power Interruption And From The Effects Of Lightning. 4. Facilities Description And Specifications All Processes And Facilities Shall Be Designed To Meet The Performance Requirements For The Proposed Project. The Inter-connectivity Between Various Plant, Support Services And Structures Must Be An Integrated Approach To Meet Operational Performance, Flexibility, Maintenance And Reliability Criteria. The Power Unit Usage Within The Battery Limit Of The Proposed Wtp Shall Not Be More Than 0.07 Kwh/m3. The Water Treatment Plant May Include But Not Be Limited To The Following Main Process System, Support Systems And Relevant Facilities: A. Raw Water Abstraction Facility The Raw Water Abstraction Facility And Pipeline Shall Have A Capacity Of 3 Mld. The Natural Flow Of The River Shall Not Be Obstructed Or Changed By Constructing A Dam, Weir, Or A Similar Structure That Could Result To Flooding Of The Nearby Properties. The Abstraction Facility Shall Consist Of The Following: • Intake Weir, Water Collection Channel And Water Collection Well • 2 Units Submersible Non Clog Pump (1 Running And 1 Spare) With Motors And Variable Frequency Drive • Pipe Lay-out • Electrical Systems And Controls B. Raw Water Pipeline The Raw Water Pipeline Must Be Made Of Spiral Welded Steel Pipe. Pipes To Be Used Must Pass The Required Test Set By The Appropriate Authority. Pipes Shall Be Laid At A Minimum Depth Of 60 Cm. Pipe Sizing Should Be In Conformance To The Hydraulic Analysis C. Raw Water Impounding Lagoon The Impounding Lagoon Have A Capacity Of A Least 30,000 M3 And Will Be Lined With Hdpe Geosynthetic Lining The Lagoon Will Also Be Installed With The Pumping System That Will Pump Water From The Lagoon To The Water Treatment Plant. The Lagoon Pumping Station Will Comprise Of 2 Units (1 Pump Running And 1 Pump Spare) Submersible, Non-clog Pumps, With A Capacity Of 3mld And A Head Of 15 Meters. D. Water Treatment Plant The 3mld Water Treatment Plant (wtp) Must Be Able To Handle And Process Incoming Raw Water With Turbidity Levels Up To 5,000 Ntu. The Wtp Shall Include But Not Limited To Receiving Well, Mixing Channel, Flocculation Basin, Sedimentation Basin, Rapid Sand Filters, Chlorination, Chemical Dosing Equipment, Clear Water Tank And Sludge Management. The Wtp Shall Be Able To Produce An Effluent That Meets The Parameters Prescribed In The 2017 Philippine National Standards For Drinking Water (pnsdw). The Wtp Should Make Use Of Gravity Flow To The Extent Possible Which Minimizes The Use Of Energy For Pumping Resulting In Low Operation Costs. It Shall Incorporate A Zero Effluent Discharge Design And Will Make Use Of An Activated Filter Media System. • Receiving Well Provide A Receiving Well At The Proposed Wtp (with A Flow Measurement Or Device) To Receive Raw Water From The Intake Facilities. Pre-chlorination And Coagulant Dosing Shall Be Done At The Receiving Well • Rapid Mix-flocculation-sedimentation Provide A 2-stage Flocculation Chamber With Agitators For Proper Dispersion And Formation Of Flocs And A Sedimentation Basin For The Separation Of The Flocs By Gravity Settling. It Shall Have Provision For Removal Of Sludge. It Should Minimize Hydraulic Head Losses Between Units To Allow Future Changes In Processes Without The Need For Re-pumping. Rapid Mix The Rapid Mix Shall Mean The Rapid Dispersion Of Chemical Through The Water To Be Treated, Using Violent Agitation. The Tanks Should Be Made Of Concrete, Equipped With Devices Capable Of Adequate Mixing For All Process Treatment Flowrates. The Retention Time Should Not Be More Than 10 Seconds. The Rapid Mix Shall Be Designed In Close Proximity With The Flocculation Tanks. Flocculation Flocculation Shall Mean The Agitation Of Water At Low Velocities For Long Periods Of Time. Inlet And Outlet Of The Tanks Shall Be Designed That It Will Minimize Short-circuiting And Destruction Of Flocs. The Tanks Shall Be Made Of Concrete And Waterproof From Wall To Wall. Drain Or Pump Shall Be Provided To Handle Dewatering And Sludge Removal In A Short Period Of Time, When Necessary. The Inlet And Outlet Velocity Should Be Between 0.15 M/s, And 0.45 M/s With A Detention Time For Flocs Formation Of At Least 20 Minutes. Sedimentation Sedimentation Shall Follow Flocculation. The Following Criteria Shall Apply To Conventional Sedimentation Units: - The Sedimentation Tank Shall Complete With Inlet And Outlet Structures, Sludge Collection And Removal Mechanism, Isolation Valves And Gates, Drainage And Safety Ladder, Catwalks And Manholes. - The Surface Overflow Or Settling Rate Should Not Be More Than 2.0 M/h. - Inlet Shall Be Designed To Distribute The Water Equally And Uniformly. The Inlet Velocity To The Sedimentation Tanks Should Not Be More Than 0.3 M/s. - Basins Should Be Provided With Sludge Collection And Removal Mechanism. Valves Shall Be Provided To Isolate For Maintenance Purposes. It Shall Be Designed To Eliminate Or Minimize Clogging. Cleaning Or Removal Of Sludge Through The Use Of Sludge Disposal Pump Shall Be Designed In Such A Way That It Could Be Facilitated/completed In A Short Period Of Time. The Sludge Shall Be Conveyed To The Sludge Lagoon Through The Drainage Facilities. • Filtration System The Filtration System Shall Serve As The Final Stage Of Treatment To Remove Suspended Solids And Colloids. It Shall Compose Of The Activate Media Filter System. The Proposed Filter Shall Also Include The Following: A Minimum Of 8 Units Of Filters With Capability To Meet Plant Capacity Even If One (1) Filter Is Taken Out For Service Or Backwashing; An Automatic Backwashing System Complete With Controls And Motorized Gates And Valves; Wash Water Collection System And An Underdrain System That Efficiently Collect The Filtered Water. Filter Run Time Should Be Between 24 And 72 Hours. Each Filter Bed Shall Be Designed For A Filtration Hydraulic Loading Rate Of Not More Than 12 M3/m2-hr When One Filter Is Out Of Service. The Multimedia Filter Shall Operate 24 Hours Per Day Whole Year Round At The Design Capacity Of 3 Mld Regardless Of The Quality Of The Raw Water. The Filter System Shall Be Designed Such That No Power Is Required During Normal Operation And During Backwash Time. The Production Capacity Of The Filtration System Should Not Be Affected And Remains The Same At 3 Mld Even When One Cell Is Undergoing Backwash Operation. - The Filtration System Shall Be Structurally Designed Sound And Safe, Made Of Reinforced Concrete, Complete With Vertical Walls Within The Filter With No Protrusion Of The Filter Walls Within The Filter Media; Head Room To Permit Normal Inspection And Operation; Walkways, Ladder Rungs And Manhole Covers Shall Be Provided As Necessary For Easy Access And Maintenance. Walkways Shall Be Provided With Stainless Steel Safely Handrails. - Appurtenances The Following Shall Be Provided For Each Filter Cell: Water Inflow Control, Backwashing Pipes And Valves, Underdrain That Will Allow Filtered Water To Flow By Gravity At Wtp Capacity And Reverse Flow During Backwashing By Gravity To Remove Accumulated Sludge. • Disinfection Facility The Disinfection Facility Shall Cover The Pre Chlorination And Post Chlorination Requirement Of The Water Treatment Plant. Provide A Disinfection System That Will Be Used To Kill Pathogenic Microorganisms. There Should Be Sufficient Excess Of Chlorine For Disinfection Including A Free Residual Chlorine Concentration Of 0.5 – 0.7 Mg/l. The Disinfection System Shall Include All Equipment Such As Chlorine Dosing Pump And Other Miscellaneous Items Necessary For Disinfection Using Granular Chlorine. The Chemical Dosing System Shall Be Located Near The Receiving Well. A Storage Area Of Capable Of Handling At Least 30 Days Of Chemical Shall Be Provided. The Disinfection Facility Shall Be Capable Of Applying The Following Dosages At The Plant’s Design Flow Rate: Minimum Dose 0.30 Ppm Average Dose 1.00 Ppm Maximum Dose 5.00 Ppm • Chemical Feeding System Provide Complete Chemical Feeding System For Dissolving And Injecting Various Chemicals To Support The Rapid Mix And Coagulation Process. Include Batch Tanks, Storage Tanks, Mechanical Mixers, Metering Screws, Pipe Work, Valves, Fittings And Associated Equipment. The Feeding Systems Shall Be Located Inside The Chemical Building. The System Shall Be Arranged To Accept Chemical Supply In Both Liquid And Powder Forms. Equip The System With Ladders, Walkways, Platforms, Handrails And Cages To Allow Safe Access To The Equipment For Operations Staff. Locate Standpipes And Hoses Near The Equipment For Maintenance. E. Sludge Lagoon The Sludge Lagoon, Or The Residual Management Facility Must Have A Capacity Of At Least 500 M3. This Must Be Designed That There Is 100% Water Recovery And Zero Effluent Discharge. F. Product Pumping Station The Treated Potable Water Will Be Pumped To The Target Service Areas With A Residual Pressure Of No Less Than 10 Psi During Peak Hours. Two Units Of Centrifugal Pump Should Be Installed (1 Running And 1 Spare) Capable Of Delivering The Requirement 3 Mld. G. Power Supply Power Supply Facility Is Inclusive But Not Limited To The Following: • 3- Phase Line With Primary Voltage Recloser (depending On Electric Cooperative Requirement) • Distribution Transformer • Stand By Generator Set With Automatic Transfer Switch The Specifications Of The Transformers And Generator Set Must Be Based On The Calculations On The Total Load Of The Whole Water Treatment Facility. H. Product Water Transmission Pipeline The Potable Water Pipeline Must Be Made Of Hdpe Pipe. Pipes To Be Used Must Pass The Required Test Set By The Appropriate Authority. Pipes Shall Be Laid At A Minimum Depth Of 60 Cm. Pipe Sizing Should Be In Conformance To The Hydraulic Analysis. Quality Assurance For Buttfuse Works Must Be Performed To Ensure That There Will Be No Leaking During Operation. The Pipes Must Be Able To Withstand A Pressure Of No Less Than 100 Psi. Estimated Length Are As Follows: Description Length 10” Mm Ø 2,058 Meters 8” Mm Ø 1,254 Meters 6” Mm Ø 3,882 Meters 4” Mm Ø 464 Meters I. Product Water Distribution Lines, Valves, Fittings And Other Appurtenances The Potable Water Pipeline Must Be Made Of Hdpe Pipe. Pipes To Be Used Must Pass The Required Test Set By The Appropriate Authority. Pipes Shall Be Laid At A Minimum Depth Of 60 Cm. Pipe Sizing Should Be In Conformance To The Hydraulic Analysis. Quality Assurance For Buttfuse Works Must Be Performed To Ensure That There Will Be No Leaking During Operation. The Pipes Must Be Able To Withstand A Pressure Of No Less Than 100 Psi. Corresponding Valves And Fittings Ang Interconnection To The Main Transmission Line Must Be Installed. Estimated Length Are As Follows: Description Length 3” Mm Ø 3,756 Meters 2” Mm Ø 6,900 Meters J. Auxiliary Facilities I. Chemical Storage The Storage Area Should Be Able To Handle Various Chemicals For 30 Days Plant Operation At Full Capacity. The Building Should Satisfy And Follow All The Necessary Safety Requirements In The Operation Of The Chemical Building. Ii. Fence Provide Inter-link Fence Around Entire Parameter Of The Plant Site. Locate Fence To The Correct Boundary And Provide Certified Survey Of Fence After Installation. Include Vehicular Gate At Entrance Roadway And An Adjacent Personnel Gate With Gate Restraints, Chains And Locks. Perimeter Lighting Shall Also Be Provided. Iii. Road Provide Paved Road Network Servicing All Areas Of The Plant And Incorporating Geometric Design And Traffic Management Features To Ensure A Free Flow Of Vehicles. Iv. Support Systems Potable Water Supply System Provide A Complete Potable Water Supply System For Drinking Water, Staff Amenities, Chemical Dilution, Cleaning, Toilets, Lavatories, Essential Process Requirements, Fire Lighting And All Other Applications. Water Shall Come From The Product Water Tank. Drainage System Provide Complete Drainage System (to Flow By Gravity) For All The Buildings, Road Networks, Water Treatment Perimeter, And Essential Area. A Separate Drainage System Shall Be Provided To Convey (by Gravity) The Sludge From The Sedimentation Basin And The Backwash Water From The Rapid Sand Filler And Other Waste Water From The Proposed Wtp Into The Sludge Lagoon Located At The Nearby Existing Wtp. Electrical Power And Control System Provide A Complete Electrical And Control System For The Plant Including The Site. Fire Control & Alarm System Provide A Complete Fire Protection Such As Smoke Detector And Alarm System In All Buildings, Control Room, Laboratory And Related Facilities And Shall Be Complying With The National Building Code Of The Philippines. Provide Fire Extinguishers At Strategic Location Inside The Plant And Support Structures. The Alarm System Shall Be Designed Audible To A Minimum Distance Of 30 Meters. Lightning Protection And Grounding System V. Miscellaneous Items That Are Deemed Necessary Provide All Necessary Items/works To Have A Complete And Efficiently Functioning Plant. 5. Process Performance Test And Guarantee, Proving And Warrantees A. After The Issuance Of The Certificate Of Completion, The Contractor Shall Supervise The Performance Testing Of The Wtp And Training Of The Procuring Entity Personnel Within A Period Of One (1) Month. The Procuring Entity Shall Supply The Operation And Maintenance Manpower And All Materials, Utilities Including Power, Fuel, Lubricants, Chemicals, Facilities, Services And Other Items Needed To Operate And Maintain The Plant. The Contractor Shall Be Responsible For The Cost Of Parts Or The Facility That May Have To Be Replaced During The Proving Period. B. The Contractor Shall For Thirty (30) Consecutive Day Demonstrate That The Completed Wtp Shall Operate In Accordance To Stated Performance Specifications And Parameters. C. The Contractor Shall Be Responsible For Making All Remedial Measures To Bring The Plant Performance And Efficiency To The Specified Level. Failure Of The Contractor To Complete All Remedial Measures Shall Authorize The Procuring Entity To Confiscate The Performance Security Or The Performance Guarantee Bond As The Case May Be And To Retain All Monies Due To The Contractor Without Prejudice To Procuring Entity's Right To File A Damage Suit. D. The Power Unit Cost Per Cubic Meter Of Treated Water At The Proposed Wtp Battery Limit Should Not Be More Than 0.15 Kwh/m3 E. The Annual Average Chemical Usage Should Not Exceed Php 1.00/m3 F. The Contractor Shall Provide One (1) Year Mechanical Warranty. G. The Contractor Shall Provide Lifetime Technical Advisory Service To The Procuring Entity. Xi. Bid Proposal Inclusions In The Preparation Of The Proposal, The Bidder Should Ensure That The Following Are Included In The Submission: 1. Technical Drawings A) Process Flow Diagram And P&id B) Site Development Plan C) Key Components Lay-out Plan D) Electrical Sld And Estimated Energy Requirement E) Conceptual Drawings And 3d Rendition Of The Water Treatment Plant And Other Facilities 2. Schedules A) Pert/cpm Network And Bar Chart/s-curve Schedule (design Stage And Construction Stage Should Be Well Defined In The Schedule. B) Manpower And Equipment Schedule C) Financial Periodic Cash Requirement 3. Capital Expenditures Proposal The Bid Should Have A Detailed Cost Breakdown Of The Components Of The Project: A) Detailed Engineering Design B) Water Treatment Plant C) Support Facilities D) Wastewater And Sludge Management Facility E) Utility Power Supply Including Transformers And Transformer Pad. F) Site Development (fencing, Road Network, Lightings, Drainage, Etc.) G) Commissioning And Testing H) Proving Period Cost Of The Inclusions Such As Hydrological And Geotechnical Studies, Site Surveys, And Insurances, May Be Individually Included In The Cost Breakdown Of The Components Where It Will Be Used. Proposal Should Also Include The Cost Of One (1) Month Of Testing And Commissioning. Cost Of Electricity And Chemicals To Be Used During The One-month Period Of Proof Of System Operations And De-bugging Must Be Become By The Bidder 4. Operations Expenditures Breakdown A Detailed Breakdown Of The Operations Expense Should Be Submitted With The Following Specifications: A) Power: • Include The Estimated Electric Consumption Starting From The Intake And The Wtp Process – Including Wastewater And Sludge Management Facility; • Electric Consumption Should Be Stated In Kwh Per Cubic Meter; • Electric Consumption Should Also Be Stated As A Philippine Peso Value Per Cubic Meter Using Php 9.00 Per Kwh As The Electric Cost. B) Chemicals: • Breakdown Of Chemical Consumption Per Cubic Meter Should Be Presented; • Chemical Consumption Per Cubic Meter Should Be Stated In Philippine Peso Value; Xii. Ded Submittal 1. Design Report, Construction And Shop Drawings A. The Design Report Shall Contain All Engineering Design Details Related To The Project Including Electrical And Mechanical Design, Structural Design And Bill Of Materials. All Design Calculations Shall Be Orderly Compiled And Submitted To The Procuring Entity As An Integral Part Of The Design Report. B. The Technical Specifications Of The Major Equipment Should Be Submitted C. The Drawings Shall Show The Complete Assembly Of The Plant With All The Equipment And Appurtenant Components. The Layout Shall Indicate The Relative Location Of The Plant With Respect To The Boundary Of The Lot. D. The Drawings Shall Show Complete Construction Details For Each Component, Piece Of Equipment, Support Structure And Access Facilities. 2. Drawings A. Drawings For Approval Drawings To Be Submitted By The Winning Bidder For Approval Shall Be Of Size A3. 3. Operation & Maintenance Manuals And List Of Spare Parts Prepare And Submit Draft Operation And Maintenance Manual With Lists Of Spare Parts For The Plant Including All Equipment, Thirty (30) Calendar Days Before The Intended Completion Date. Submit The Completed Operation And Maintenance Manual Within Two Weeks Of Receiving Review Comments In The Form Of Two Digital Copies On Cd And Four Hard Copies Using The Latest Versions Of Word And Autocad With Supplementary Drawing And Image Files In Pdf Format. Manuals Shall Be In Metric, A4 In Size With Three Ring Binders With Durable Hard Covers. Drawings Shall Be In Metric, A3 Size Covers And Held Together Using Three Removable Brass Male/female Screws. All Drawings Shall Be In A3 Size. The Operation And Maintenance Manuals Shall: I. Cover All Aspects Of The Works Ii. Provide 'general Principles Of Operation' For The Plant. The General Principles Of Operation Shall Be Prepared By The Designers And Should Include The Necessary Information For Operators To Effectively Operate And Maintain The Works. Iii. Incorporate Safety, Environmental And Quality Issues. Iv. Have Detailed Indexes And Cross Referencing. V. The Operations Manual And The Maintenance Manual Shall Be Bounded Separately. A. Operation Manual A Single Operation Manual Shall Be Provided For The Operation Of The Plant. The Manual Shall Include But Not Be Limited To: I. Title Page: Project, Procuring Entity's And Contractor’s Name, Address And Telephone Number And Contract Number. Ii. Index: Include A Comprehensive Index Iii. General Description • Location • Site Layout, Process And Instrumentation Diagrams, Hydraulic Profile • Description Of Process And Effluent Criteria • Design Criteria Iv. Safety Management V. Environmental Management Vi. Detail Operation (for Each Process Unit) • Describe Each Process Unit Including Size And Number Of Mechanical/ Electrical Units • Mode Of Operation (start, Shutdown, Manual And Auto Control) • Performance Criteria For Each Process Unit/facility • Sampling Points • Troubleshooting • Record Keeping Requirements • Duty Statements (for Operators) • Operating Procedures (covering Safely And Environmental Procedures) • Environmental And Emergency Response • Sampling And Monitoring Requirements - Include Performance Criteria For Each Process Unit - Monitoring Of The Receiving Environment (waterways, Noise And Odors) • Cross Reference To Maintenance Manuals - Provide Maintenance Manuals To Support This Operations Manual For All Mechanical And Electrical Equipment. B. Maintenance Manual Prepare Maintenance Manuals For All Individual Items Of Equipment. The Manuals Shall Include But Not Be Limited To: I. Title Page: Project, Procuring Entity's Name, Address And Telephone Number, Contractor's Name, Address And Telephone Number And Contract Number. Ii. Index: Include A Comprehensive Index. Iii. Description: A Full Description Of The Equipment With A Tabulation Of Dimensions And Performance Ratings. Iv. Principles Of Operation: Basic Working Description, Including Novel Features And Any Automatic Control. V. Operating Instructions: A Step-by-step Procedure Organized In Sections Containing The Following: • Pre-start Check-up • Starting • Continuous Operation • Stopping • Emergency Stopping • Abnormal Operation (as Applicable) Vi. Installation And Commissioning Instructions: Details Of Standards And Procedures For Transporting And Installing The Equipment. Including A Step-by-step Procedure For Mounting Or Erecting, Wiring And Lubricating The Equipment. Alignment Tolerances And Check Requirements Shall Be Stated. Vii. The Commissioning Instructions Shall Include Step By Step Procedures Before And During Start-up, After Starting And Operational Tests During Continuous Operation. Viii. Routine Maintenance - Step By Step Procedure For Preventive Maintenance Work Carried Out At Intervals Of 2 Weeks Or Less. Ix. Periodic Maintenance: Step By Step Procedure For Fault Correction And Preventive Maintenance Carried Out At Intervals In Excess Of Two Weeks, Involving Replacement Of Spare Parts And Consumables. A List Of Special Tools Shall Be Included. X. Test Data And Troubleshooting: Instructions To Qualified Tradesmen For Assessing The Operational Performance Of The Equipment. Xi. Spare Parts List: Illustrations And Schedules For Identification And Specifications Of All Items In The Equipment. Exploded Diagrams Are Required. The Recommended Spare Parts Stock For One Year Shall Be Indicated. Xiii. Personnel & Equipment Requirement The Bidder Must Demonstrate That It Has Designed And Constructed Similar Water Treatment Facilities And Has The Personnel For The Key Positions That Meet The Following Requirements: Item Position Total Work Experience (years) Similar Work Experience (years) 1 Project Manager 10 5 Design 2 Water Treatment Specialist (chemical Engineer) 5 3 3 Sanitary Engineer 5 2 4 Professional Mechanical Engineer 5 3 5 Professional Electrical Engineer 5 3 6 Structural Engineer 5 2 Build 7 Project Engineer 5 3 8 Civil Engineer 5 3 9 Mechanical Engineer 5 3 10 Electrical Engineer 5 3 11 Safety Officer 5 2 The Contractor Shall Provide Details Of The Proposed Personnel And Their Experience Records. C. Equipment The Contractor Must Demonstrate That It Will Have Access To The Key Equipment Listed Hereafter: Item Equipment Type And Characteristics Quantity 1 Dump Truck 1 2 Backhoe 1 3 Roller Compactor 1 4 Concrete Vibrator 1 5 Bagger Mixer 2 6 Bar Cutter 1 7 Welding Machine 1 8 Boom Truck 1

Details: Description Bids And Awards Committee Iloilo Provincial Government Procurement Of Agricultural Equipment Bid No. Agr-25-223-b Philippine Bidding Documents Sixth Edition July 2020 Table Of Contents Section I. Invitation To Bid 3 Section Ii. Instructions To Bidders 5 1. Scope Of Bid 5 2. Funding Information 5 3. Bidding Requirements 5 4. Corrupt, Fraudulent, Collusive, And Coercive Practices 5 5. Eligible Bidders 5 6. Origin Of Goods 6 7. Subcontracts 7 8. Pre-bid Conference 7 9. Clarification And Amendment Of Bidding Documents 7 10. Documents Comprising The Bid: Eligibility And Technical Components 7 11. Documents Comprising The Bid: Financial Component 7 12. Bid Prices 8 13. Bid And Payment Currencies 8 14. Bid Security 8 15. Sealing And Marking Of Bids 9 16. Deadline For Submission Of Bids 9 17. Opening And Preliminary Examination Of Bids 9 18. Domestic Preference 9 19. Detailed Evaluation And Comparison Of Bids 9 20. Post-qualification 10 21. Signing Of The Contract 10 Section Iii. Bid Data Sheet 11 Section Iv. General Conditions Of Contract 12 1. Scope Of Contract 12 2. Advance Payment And Terms Of Payment 12 3. Performance Security 12 4. Inspection And Tests 12 5. Warranty 13 6. Liability Of The Supplier 13 Section V. Special Conditions Of Contract 14 Section Vi. Schedule Of Requirements 16 Section Vii. Technical Specifications 17 Section Viii. Checklist Of Technical And Financial Documents 19 Section I. Invitation To Bid Purchase Of Agricultural Equipment Bid No. Agr-25-223-b 1. The Iloilo Provincial Government Through The 20% Nta Development Fund Fy-2025 Intends To Apply The Sum Of Three Million Eight Hundred Thousand Pesos (php 3,800,000.00) Being The Abc To Payments Under The Contract For The Purchase Of Agricultural Equipment. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. 2. The Iloilo Provincial Government Now Invites Bids For The Above Procurement Project. Delivery Of The Goods Is Required By Within 45 Days Upon Receipt Of The Notice To Proceed (ntp). Bidders Should Have Completed, Within Three (3) Years From The Date Of Submission And Receipt Of Bids, A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii (instructions To Bidders). 3. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using A Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) No. 9184. Bidding Is Restricted To Filipino Citizens/sole Proprietorships, Partnerships, Or Organizations With At Least Sixty Percent (60%) Interest Or Outstanding Capital Stock Belonging To Citizens Of The Philippines, And To Citizens Or Organizations Of A Country The Laws Or Regulations Of Which Grant Similar Rights Or Privileges To Filipino Citizens, Pursuant To Ra No. 5183. 4. Prospective Bidders May Obtain Further Information From The Bids And Awards Committee Secretariat Of The Iloilo Provincial Government And Inspect The Bidding Documents At The Address Given Below During 8:00 A.m. To 5:00 P.m. 5. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders On March 20, 2025 From The Given Address And Website(s) Below And Upon Payment Of The Applicable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb, In The Amount Of Five Thousand Pesos (php 5,000.00). The Procuring Entity Shall Allow The Bidder To Present Its Proof Of Payment For The Fees In Person. 6. The Iloilo Provincial Government Will Hold A Pre-bid Conference On March 27, 2025 At 9:00 A.m. At The N/a And/or Through Video Conferencing Or Webcasting, Upon Request At Least Three (3) Days Before The Pre-bid Conference, Via Zoom Or Other Videoconferencing Portals, Which Shall Be Open To Prospective Bidders. 7. Bids Must Be Duly Received By The Bac Secretariat Through Manual Submission At The 5th Floor, Bac Secretariat Office, Iloilo Provincial Capitol, Iloilo City On Or Before April 10, 2025 At 9:00 A.m. Late Bids Shall Not Be Accepted. 8. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 14. 9. Bid Opening Shall Be On April 10, 2025 At 9:01 A.m.at The 5th Floor, Bac Secretariat Office, Iloilo Provincial Capitol, Iloilo City Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend The Activity. 10. A. The Participating Bidder/supplier Or Its Authorized Representative Must Indicate In Any Of The Eligibility Documents, An Email Address Or A Working Fax Number. The Absence Of Which Shall Be A Ground For Disqualification. Notice To The Bidder/supplier Through The Use Of Either Of These Means (email/fax) Is Considered Sufficient Notice. The Date Of Filing Of Reconsideration And All Communications With The Bac Shall Be Its (bac) Date Of Receipt. B. The Bidder(s)/awardee(s) Or Its Authorized Representative Must Conform To The Notice Of Award Within Three (3) Calendar Days From Receipt Of Such Notice And The Winning Bidder Shall Post The Required Performance Security And Enter Into Contract With The Procuring Entity Within Ten (10) Calendar Days From Receipt By The Winning Bidder Of The Notice Of Award In Accordance With Section 37.2.1 Of The Revised Irr Of R.a. No. 9184. C. The Bidder/supplier Must Have No Pending Unaccepted Notice To Proceed Three (3) Days From The Date Of Acceptance And Signing Of The Purchase Order. Otherwise, It Shall Be A Ground For Disqualification And The Bidder Will Be Rated "failed" During The Preliminary Examination Of Bids And/or Its Bid Shall Be Declared As "non-responsive" During Post-qualification. D. The Bidder/supplier Must Have No Notice Of Award Pending Its Conformity Three (3) Days From The Date Of Its Receipt Of The Notice Of Award. Otherwise, It Shall Be Aground For Disqualification And The Bidder Will Be Rated "failed" During The Preliminary Examination Of Bids And/or Its Bid Shall Be Declared As "non-responsive" During Post-qualification. E. The Bidder/supplier Shall Submit A List Of All Its Ongoing And Completed Projects With The Iloilo Provincial Government Indicating The Delivery Periods And Accomplishments Of Such Projects. F. The Bidder/supplier At The Time Of The Bidding Must Have No Pending Unposted Performance Or Warranty Security, As The Case May Be, Beyond The Period Allowed In The Notice Of Award. Otherwise, It Shall Be A Ground For Disqualification And The Bidder Will Be Rated "failed" During The Preliminary Examination Of Bids And/or Its Bid Shall Be Declared As "non-responsive" During Post-qualification. 11. The Iloilo Provincial Government Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Irr Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 12. For Further Information, Please Refer To: Atty. Raemman M. Lagrada Bac Secretariat Head 5th Floor, Bids And Awards Committee Iloilo Provincial Capitol Email Address: Ipg_bacs@yahoo.com Website: Iloilo.gov.ph Telephone Number: (033) 336-0736 13. You May Visit The Following Websites For Downloading Of Bidding Documents: Ipg.gov.ph And/or Philgeps.com March 7, 2025 Atty. Dennis T. Ventilacion Chairman, Bids And Awards Committee Section Ii. Instructions To Bidders 1. Scope Of Bid The Procuring Entity, Iloilo Provincial Government Wishes To Receive Bids For The Purchase Of Agricultural Equipment With Bid No. Agr-25-223-b. The Procurement Project (referred To Herein As “project”) Is Composed Of One (1) Item(s), The Details Of Which Are Described In Section Vii (technical Specifications). 2. Funding Information 2.1. The Gop Through The Source Of Funding As Indicated Below For 2025 In The Amount Of Three Million Eight Hundred Thousand Pesos (php 3,800,000.00) 2.2. The Source Of Funding Is: Lgus, The Annual Or Supplemental Budget, As Approved By The Sanggunian. 3. Bidding Requirements The Bidding For The Project Shall Be Governed By All The Provisions Of Ra No. 9184 And Its 2016 Revised Irr, Including Its Generic Procurement Manuals And Associated Policies, Rules And Regulations As The Primary Source Thereof, While The Herein Clauses Shall Serve As The Secondary Source Thereof. Any Amendments Made To The Irr And Other Gppb Issuances Shall Be Applicable Only To The Ongoing Posting, Advertisement, Or Ib By The Bac Through The Issuance Of A Supplemental Or Bid Bulletin. The Bidder, By The Act Of Submitting Its Bid, Shall Be Deemed To Have Verified And Accepted The General Requirements Of This Project, Including Other Factors That May Affect The Cost, Duration And Execution Or Implementation Of The Contract, Project, Or Work And Examine All Instructions, Forms, Terms, And Project Requirements In The Bidding Documents. 4. Corrupt, Fraudulent, Collusive, And Coercive Practices The Procuring Entity, As Well As The Bidders And Suppliers, Shall Observe The Highest Standard Of Ethics During The Procurement And Execution Of The Contract. They Or Through An Agent Shall Not Engage In Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices Defined Under Annex “i” Of The 2016 Revised Irr Of Ra No. 9184 Or Other Integrity Violations In Competing For The Project. 5. Eligible Bidders 5.1. Only Bids Of Bidders Found To Be Legally, Technically, And Financially Capable Will Be Evaluated. 5.2. A. Foreign Ownership Exceeding Those Allowed Under The Rules May Participate Pursuant To: I. When A Treaty Or International Or Executive Agreement As Provided In Section 4 Of The Ra No. 9184 And Its 2016 Revised Irr Allow Foreign Bidders To Participate; Ii. Citizens, Corporations, Or Associations Of A Country, Included In The List Issued By The Gppb, The Laws Or Regulations Of Which Grant Reciprocal Rights Or Privileges To Citizens, Corporations, Or Associations Of The Philippines; Iii. When The Goods Sought To Be Procured Are Not Available From Local Suppliers; Or Iv. When There Is A Need To Prevent Situations That Defeat Competition Or Restrain Trade. 5.3. Pursuant To Section 23.4.1.3 Of The 2016 Revised Irr Of Ra No.9184, The Bidder Shall Have An Slcc That Is At Least One (1) Contract Similar To The Project The Value Of Which, Adjusted To Current Prices Using The Psa’s Cpi, Must Be At Least Equivalent To: A. For The Procurement Of Non-expendable Supplies And Services: The Bidder Must Have Completed A Single Contract That Is Similar To This Project, Equivalent To At Least Fifty Percent (50%) Of The Abc. B. For The Procurement Of Expendable Supplies: The Bidder Must Have Completed A Single Contract That Is Similar To This Project, Equivalent To At Least Twenty-five Percent (25%) Of The Abc. C. For Procurement Where The Procuring Entity Has Determined, After The Conduct Of Market Research, That Imposition Of Either (a) Or (b) Will Likely Result To Failure Of Bidding Or Monopoly That Will Defeat The Purpose Of Public Bidding: The Bidder Should Comply With The Following Requirements: [select Either Failure Or Monopoly Of Bidding Based On Market Research Conducted] I. Completed At Least Two (2) Similar Contracts, The Aggregate Amount Of Which Should Be Equivalent To At Least Fifty Percent (50%) In The Case Of Non-expendable Supplies And Services Or Twenty-five Percent (25%) In The Case Of Expendable Supplies] Of The Abc For This Project; And Ii. The Largest Of These Similar Contracts Must Be Equivalent To At Least Half Of The Percentage Of The Abc As Required Above. 5.4. The Bidders Shall Comply With The Eligibility Criteria Under Section 23.4.1 Of The 2016 Irr Of Ra No. 9184. 6. Origin Of Goods There Is No Restriction On The Origin Of Goods Other Than Those Prohibited By A Decision Of The Un Security Council Taken Under Chapter Vii Of The Charter Of The Un, Subject To Domestic Preference Requirements Under Itb Clause 18. 7. Subcontracts 7.1. The Bidder May Subcontract Portions Of The Project To The Extent Allowed By The Procuring Entity As Stated Herein, But In No Case More Than Twenty Percent (20%) Of The Project. The Procuring Entity Has Prescribed That: Subcontracting Is Not Allowed. 8. Pre-bid Conference The Procuring Entity Will Hold A Pre-bid Conference For This Project On The Specified Date And Time And Either At Its Physical Address As Indicated In Paragraph 6 Of The Ib. 9. Clarification And Amendment Of Bidding Documents Prospective Bidders May Request For Clarification On And/or Interpretation Of Any Part Of The Bidding Documents. Such Requests Must Be In Writing And Received By The Procuring Entity, Either At Its Given Address Or Through Electronic Mail Indicated In The Ib, At Least Ten (10) Calendar Days Before The Deadline Set For The Submission And Receipt Of Bids. 10. Documents Comprising The Bid: Eligibility And Technical Components 10.1. The First Envelope Shall Contain The Eligibility And Technical Documents Of The Bid As Specified In Section Viii (checklist Of Technical And Financial Documents). 10.2. The Bidder’s Slcc As Indicated In Itb Clause 5.3 Should Have Been Completed Within Three (3) Years Prior To The Deadline For The Submission And Receipt Of Bids. 10.3. If The Eligibility Requirements Or Statements, The Bids, And All Other Documents For Submission To The Bac Are In Foreign Language Other Than English, It Must Be Accompanied By A Translation In English, Which Shall Be Authenticated By The Appropriate Philippine Foreign Service Establishment, Post, Or The Equivalent Office Having Jurisdiction Over The Foreign Bidder’s Affairs In The Philippines. Similar To The Required Authentication Above, For Contracting Parties To The Apostille Convention, Only The Translated Documents Shall Be Authenticated Through An Apostille Pursuant To Gppb Resolution No. 13-2019 Dated 23 May 2019. The English Translation Shall Govern, For Purposes Of Interpretation Of The Bid. 11. Documents Comprising The Bid: Financial Component 11.1. The Second Bid Envelope Shall Contain The Financial Documents For The Bid As Specified In Section Viii (checklist Of Technical And Financial Documents). 11.2. If The Bidder Claims Preference As A Domestic Bidder Or Domestic Entity, A Certification Issued By Dti Shall Be Provided By The Bidder In Accordance With Section 43.1.3 Of The 2016 Revised Irr Of Ra No. 9184. 11.3. Any Bid Exceeding The Abc Indicated In Paragraph 1 Of The Ib Shall Not Be Accepted. 11.4. For Foreign-funded Procurement, A Ceiling May Be Applied To Bid Prices Provided The Conditions Are Met Under Section 31.2 Of The 2016 Revised Irr Of Ra No. 9184. 12. Bid Prices 12.1. Prices Indicated On The Price Schedule Shall Be Entered Separately In The Following Manner: A. For Goods Offered From Within The Procuring Entity’s Country: I. The Price Of The Goods Quoted Exw (ex-works, Ex-factory, Ex-warehouse, Ex-showroom, Or Off-the-shelf, As Applicable); Ii. The Cost Of All Customs Duties And Sales And Other Taxes Already Paid Or Payable; Iii. The Cost Of Transportation, Insurance, And Other Costs Incidental To Delivery Of The Goods To Their Final Destination; And Iv. The Price Of Other (incidental) Services, If Any, Listed In E. B. For Goods Offered From Abroad: I. Unless Otherwise Stated In The Bds, The Price Of The Goods Shall Be Quoted Delivered Duty Paid (ddp) With The Place Of Destination In The Philippines As Specified In The Bds. In Quoting The Price, The Bidder Shall Be Free To Use Transportation Through Carriers Registered In Any Eligible Country. Similarly, The Bidder May Obtain Insurance Services From Any Eligible Source Country. Ii. The Price Of Other (incidental) Services, If Any, As Listed In Section Vii (technical Specifications). 13. Bid And Payment Currencies 13.1. For Goods That The Bidder Will Supply From Outside The Philippines, The Bid Prices May Be Quoted In The Local Currency Or Tradeable Currency Accepted By The Bsp At The Discretion Of The Bidder. However, For Purposes Of Bid Evaluation, Bids Denominated In Foreign Currencies, Shall Be Converted To Philippine Currency Based On The Exchange Rate As Published In The Bsp Reference Rate Bulletin On The Day Of The Bid Opening. 13.2. Payment Of The Contract Price Shall Be Made In: Philippine Pesos. 14. Bid Security 14.1. The Bidder Shall Submit A Bid Securing Declaration Or Any Form Of Bid Security In The Amount Indicated In The Bds, Which Shall Be Not Less Than The Percentage Of The Abc In Accordance With The Schedule In The Bds. 14.2. The Bid And Bid Security Shall Be Valid Until One Hundred Twenty (120) Days. Any Bid Not Accompanied By An Acceptable Bid Security Shall Be Rejected By The Procuring Entity As Non-responsive. 15. Sealing And Marking Of Bids Each Bidder Shall Submit One Copy Of The First And Second Components Of Its Bid. The Procuring Entity May Request Additional Hard Copies And/or Electronic Copies Of The Bid. However, Failure Of The Bidders To Comply With The Said Request Shall Not Be A Ground For Disqualification. 16. Deadline For Submission Of Bids 16.1. The Bidders Shall Submit On The Specified Date And Time At Its Physical Address As Indicated In Paragraph 7 Of The Ib. 17. Opening And Preliminary Examination Of Bids 17.1. The Bac Shall Open The Bids In Public At The Time, On The Date, And At The Place Specified In Paragraph 9 Of The Ib. The Bidders’ Representatives Who Are Present Shall Sign A Register Evidencing Their Attendance. In Case Videoconferencing, Webcasting Or Other Similar Technologies Will Be Used, Attendance Of Participants Shall Likewise Be Recorded By The Bac Secretariat. In Case The Bids Cannot Be Opened As Scheduled Due To Justifiable Reasons, The Rescheduling Requirements Under Section 29 Of The 2016 Revised Irr Of Ra No. 9184 Shall Prevail. 17.2. The Preliminary Examination Of Bids Shall Be Governed By Section 30 Of The 2016 Revised Irr Of Ra No. 9184. 18. Domestic Preference 18.1. The Procuring Entity Will Grant A Margin Of Preference For The Purpose Of Comparison Of Bids In Accordance With Section 43.1.2 Of The 2016 Revised Irr Of Ra No. 9184. 19. Detailed Evaluation And Comparison Of Bids 19.1. The Procuring Bac Shall Immediately Conduct A Detailed Evaluation Of All Bids Rated “passed,” Using Non-discretionary Pass/fail Criteria. The Bac Shall Consider The Conditions In The Evaluation Of Bids Under Section 32.2 Of The 2016 Revised Irr Of Ra No. 9184. 19.2. If The Project Allows Partial Bids, Bidders May Submit A Proposal On Any Of The Lots Or Items, And Evaluation Will Be Undertaken On A Per Lot Or Item Basis, As The Case Maybe. In This Case, The Bid Security As Required By Itb Clause 15 Shall Be Submitted For Each Lot Or Item Separately. 19.3. The Descriptions Of The Lots Or Items Shall Be Indicated In Section Vii (technical Specifications), Although The Abcs Of These Lots Or Items Are Indicated In The Bds For Purposes Of The Nfcc Computation Pursuant To Section 23.4.2.6 Of The 2016 Revised Irr Of Ra No. 9184. The Nfcc Must Be Sufficient For The Total Of The Abcs For All The Lots Or Items Participated In By The Prospective Bidder. 19.4. The Project Shall Be Awarded As Follows: Complete Bid - One Project Having Several Items That Shall Be Awarded As One Contract In Case Of Complete Bid. Line Bidding/partial Bidding - One Project Having Several Items, Which Shall Be Awarded As Separate Contracts Per Item 19.5. Except For Bidders Submitting A Committed Line Of Credit From A Universal Or Commercial Bank In Lieu Of Its Nfcc Computation, All Bids Must Include The Nfcc Computation Pursuant To Section 23.4.1.4 Of The 2016 Revised Irr Of Ra No. 9184, Which Must Be Sufficient For The Total Of The Abcs For All The Lots Or Items Participated In By The Prospective Bidder. For Bidders Submitting The Committed Line Of Credit, It Must Be At Least Equal To Ten Percent (10%) Of The Abcs For All The Lots Or Items Participated In By The Prospective Bidder. 20. Post-qualification Within A Non-extendible Period Of Five (5) Calendar Days From Receipt By The Bidder Of The Notice From The Bac That It Submitted The Lowest Calculated Bid, The Bidder Shall Submit Its Latest Income And Business Tax Returns Filed And Paid Through The Bir Electronic Filing And Payment System (efps) And Other Appropriate Licenses And Permits Required By Law And Stated In The Bds. 21. Signing Of The Contract 21.1. The Documents Required In Section 37.2 Of The 2016 Revised Irr Of Ra No. 9184 Shall Form Part Of The Contract. Additional Contract Documents Are Indicated In The Bds. Section Iii. Bid Data Sheet Itb Clause 5.3 For This Purpose, Contracts Similar To The Project Shall Be: A. Refers To The Contracts To Be Bid Or The Object Of The Contract; B. Completed Within Three (3) Years Prior To The Deadline For The Submission And Receipt Of Bids. 7.1 Subcontracting Is Not Allowed. 12 The Price Of The Goods Shall Be Quoted Ddp Art Center, Nanga, Pototan, Iloilo Or The Applicable International Commercial Terms (incoterms) For This Project. 14.1 The Bid Security Shall Be In The Form Of A Bid Securing Declaration, Or Any Of The Following Forms And Amounts: A. The Amount Of Not Less Than Two Percent (2%) Of Abc, If Bid Security Is In Cash, Cashier’s/manager’s Check, Bank Draft/guarantee Or Irrevocable Letter Of Credit; Or B. The Amount Of Not Less Than Five Percent (5%) Of Abc, If Bid Security Is In Surety Bond. 15 Bidders Shall Prepare An Original Of The First (eligibility And Technical) And Second (financial) Envelopes. In Addition, Bidders Shall Submit Separate Copies Of The First And Second Envelopes (copy 1, Copy 2) And Each Set Of Documents Must Clearly Indicate Whether The Same Is Original, Copy 1, Or Copy 2. In The Event Of Any Discrepancy Between The Original And The Copies, The Original Shall Prevail. 19.3 No Further Instructions. 20.2 For The Procurement Of Drugs And Medicines And Medical Equipment/supplies, The Bidder Shall Submit The Following: A. Certificate Of Product Registration From Food And Drug Administration (fda) For Easy Validation During The Post-qualification; B. Certificate If Good Manufacturing Practice From Fda, For Easy Validation During The Post-qualification; C. Batch Release Certificate From Fda, For Easy Validation During The Post-qualification; D. If The Supplier Is Not The Manufacturer, Certification From The Manufacturer That The Supplier Is An Authorized Distributor/ Dealer Of The Products / Items For Easy Validation During The Post-qualification; E. For The Procurement Of Regulated Drugs, The Applicable Type Of S-license: S-1, S-3 (retailer) S-4 (wholesaler) S-5c (manufacturer) S-5d (bulk Depot/storage) S-5e S-5i (importer); F. License To Operate (lto) Issued By Fda, If Applicable; G. After-sales Services/parts, If Applicable; H. Manpower Requirements, If Applicable. 21.2 No Further Instructions. Section Iv. General Conditions Of Contract 1. Scope Of Contract This Contract Shall Include All Such Items, Although Not Specifically Mentioned, That Can Be Reasonably Inferred As Being Required For Its Completion As If Such Items Were Expressly Mentioned Herein. All The Provisions Of Ra No. 9184 And Its 2016 Revised Irr, Including The Generic Procurement Manual, And Associated Issuances, Constitute The Primary Source For The Terms And Conditions Of The Contract, And Thus, Applicable In Contract Implementation. Herein Clauses Shall Serve As The Secondary Source For The Terms And Conditions Of The Contract. This Is Without Prejudice To Sections 74.1 And 74.2 Of The 2016 Revised Irr Of Ra No. 9184 Allowing The Gppb To Amend The Irr, Which Shall Be Applied To All Procurement Activities, The Advertisement, Posting, Or Invitation Of Which Were Issued After The Effectivity Of The Said Amendment. Additional Requirements For The Completion Of This Contract Shall Be Provided In The Special Conditions Of Contract (scc). 2. Advance Payment And Terms Of Payment 2.1. Advance Payment Of The Contract Amount Is Provided Under Annex “d” Of The Revised 2016 Irr Of Ra No. 9184. 2.2. The Procuring Entity Is Allowed To Determine The Terms Of Payment On The Partial Or Staggered Delivery Of The Goods Procured, Provided Such Partial Payment Shall Correspond To The Value Of The Goods Delivered And Accepted In Accordance With Prevailing Accounting And Auditing Rules And Regulations. The Terms Of Payment Are Indicated In The Scc. 3. Performance Security Within Ten (10) Calendar Days From Receipt Of The Notice Of Award By The Bidder From The Procuring Entity But In No Case Later Than Prior To The Signing Of The Contract By Both Parties, The Successful Bidder Shall Furnish The Performance Security In Any Of The Forms Prescribed In Section 39 Of The 2016 Revised Irr Of Ra No. 9184. 4. Inspection And Tests The Procuring Entity Or Its Representative Shall Have The Right To Inspect And/or To Test The Goods To Confirm Their Conformity To The Project Specifications At No Extra Cost To The Procuring Entity In Accordance With The Generic Procurement Manual. In Addition To Tests In The Scc, Section Iv (technical Specifications) Shall Specify What Inspections And/or Tests The Procuring Entity Requires, And Where They Are To Be Conducted. The Procuring Entity Shall Notify The Supplier In Writing, In A Timely Manner, Of The Identity Of Any Representatives Retained For These Purposes. All Reasonable Facilities And Assistance For The Inspection And Testing Of Goods, Including Access To Drawings And Production Data, Shall Be Provided By The Supplier To The Authorized Inspectors At No Charge To The Procuring Entity. 5. Warranty 6.1. In Order To Assure That Manufacturing Defects Shall Be Corrected By The Supplier, A Warranty Shall Be Required From The Supplier As Provided Under Section 62.1 Of The 2016 Revised Irr Of Ra No. 9184. 6.2. The Procuring Entity Shall Promptly Notify The Supplier In Writing Of Any Claims Arising Under This Warranty. Upon Receipt Of Such Notice, The Supplier Shall, Repair Or Replace The Defective Goods Or Parts Thereof Without Cost To The Procuring Entity, Pursuant To The Generic Procurement Manual. 6. Liability Of The Supplier The Supplier’s Liability Under This Contract Shall Be As Provided By The Laws Of The Republic Of The Philippines. If The Supplier Is A Joint Venture, All Partners To The Joint Venture Shall Be Jointly And Severally Liable To The Procuring Entity. Section V. Special Conditions Of Contract Gcc Clause 1 Delivery And Documents – For Purposes Of The Contract, “exw,” “fob,” “fca,” “cif,” “cip,” “ddp” And Other Trade Terms Used To Describe The Obligations Of The Parties Shall Have The Meanings Assigned To Them By The Current Edition Of Incoterms Published By The International Chamber Of Commerce, Paris. The Delivery Terms Of This Contract Shall Be As Follows: [for Goods Supplied From Within The Philippines, State:] “the Delivery Terms Applicable To This Contract Are Delivered To Art Center, Nanga, Pototan, Iloilo. Risk And Title Will Pass From The Supplier To The Procuring Entity Upon Receipt And Final Acceptance Of The Goods At Their Final Destination.” Delivery Of The Goods Shall Be Made By The Supplier In Accordance With The Terms Specified In Section Vi (schedule Of Requirements). For Purposes Of This Clause The Procuring Entity’s Representative At The Project Site Is The Authorized Employee/official Of The Iloilo Provincial Government. Incidental Services – The Supplier Is Required To Provide All Of The Following Services, Including Additional Services, If Any, Specified In Section Vi. Schedule Of Requirements: A. Performance Or Supervision Of On-site Assembly And/or Start-up Of The Supplied Goods; B. Furnishing Of Tools Required For Assembly And/or Maintenance Of The Supplied Goods; C. Furnishing Of A Detailed Operations And Maintenance Manual For Each Appropriate Unit Of The Supplied Goods; The Contract Price For The Goods Shall Include The Prices Charged By The Supplier For Incidental Services And Shall Not Exceed The Prevailing Rates Charged To Other Parties By The Supplier For Similar Services. Packaging – The Supplier Shall Provide Such Packaging Of The Goods As Is Required To Prevent Their Damage Or Deterioration During Transit To Their Final Destination, As Indicated In This Contract. The Packaging Shall Be Sufficient To Withstand, Without Limitation, Rough Handling During Transit And Exposure To Extreme Temperatures, Salt And Precipitation During Transit, And Open Storage. Packaging Case Size And Weights Shall Take Into Consideration, Where Appropriate, The Remoteness Of The Goods’ Final Destination And The Absence Of Heavy Handling Facilities At All Points In Transit. The Packaging, Marking, And Documentation Within And Outside The Packages Shall Comply Strictly With Such Special Requirements As Shall Be Expressly Provided For In The Contract, Including Additional Requirements, If Any, Specified Below, And In Any Subsequent Instructions Ordered By The Procuring Entity. The Outer Packaging Must Be Clearly Marked On At Least Four (4) Sides As Follows: Name Of The Procuring Entity Name Of The Supplier Contract Description Final Destination Gross Weight Any Special Lifting Instructions Any Special Handling Instructions A Packaging List Identifying The Contents And Quantities Of The Package Is To Be Placed On An Accessible Point Of The Outer Packaging If Practical. If Not Practical The Packaging List Is To Be Placed Inside The Outer Packaging But Outside The Secondary Packaging. Transportation – Where The Supplier Is Required Under Contract To Deliver The Goods Cif, Cip, Or Ddp, Transport Of The Goods To The Port Of Destination Or Such Other Named Place Of Destination In The Philippines, As Shall Be Specified In This Contract, Shall Be Arranged And Paid For By The Supplier, And The Cost Thereof Shall Be Included In The Contract Price. Where The Supplier Is Required Under This Contract To Transport The Goods To A Specified Place Of Destination Within The Philippines, Defined As The Project Site, Transport To Such Place Of Destination In The Philippines, Including Insurance And Storage, As Shall Be Specified In This Contract, Shall Be Arranged By The Supplier, And Related Costs Shall Be Included In The Contract Price. Where The Supplier Is Required Under Contract To Deliver The Goods Cif, Cip Or Ddp, Goods Are To Be Transported On Carriers Of Philippine Registry. In The Event That No Carrier Of Philippine Registry Is Available, Goods May Be Shipped By A Carrier Which Is Not Of Philippine Registry Provided That The Supplier Obtains And Presents To The Procuring Entity Certification To This Effect From The Nearest Philippine Consulate To The Port Of Dispatch. In The Event That Carriers Of Philippine Registry Are Available But Their Schedule Delays The Supplier In Its Performance Of This Contract The Period From When The Goods Were First Ready For Shipment And The Actual Date Of Shipment The Period Of Delay Will Be Considered Force Majeure. The Procuring Entity Accepts No Liability For The Damage Of Goods During Transit Other Than Those Prescribed By Incoterms For Ddp Deliveries. In The Case Of Goods Supplied From Within The Philippines Or Supplied By Domestic Suppliers Risk And Title Will Not Be Deemed To Have Passed To The Procuring Entity Until Their Receipt And Final Acceptance At The Final Destination. 2.2 Partial Payment Is Not Allowed. 4 The Inspections And Tests That Will Be Conducted Are Through Physical Inspection. Section Vi. Schedule Of Requirements The Delivery Schedule Expressed As Weeks/months Stipulates Hereafter A Delivery Date Which Is The Date Of Delivery To The Project Site. Item Number Description Quantity Total Delivered, Weeks/months 1 Heated Mechanical Grain Dryer-recirculating Batch Dryer 1 1 ___________________________________ Signature Over Printed Name Section Vii. Technical Specifications Bid No.: Agr-25-223-b Item Specification Statement Of Compliance [bidders Must State Here Either “comply” Or “not Comply” Against Each Of The Individual Parameters Of Each Specification Stating The Corresponding Performance Parameter Of The Equipment Offered. Statements Of “comply” Or “not Comply” Must Be Supported By Evidence In A Bidders Bid And Cross-referenced To That Evidence. Evidence Shall Be In The Form Of Manufacturer’s Un-amended Sales Literature, Unconditional Statements Of Specification And Compliance Issued By The Manufacturer, Samples, Independent Test Data Etc., As Appropriate. A Statement That Is Not Supported By Evidence Or Is Subsequently Found To Be Contradicted By The Evidence Presented Will Render The Bid Under Evaluation Liable For Rejection. A Statement Either In The Bidder’s Statement Of Compliance Or The Supporting Evidence That Is Found To Be False Either During Bid Evaluation, Post-qualification Or The Execution Of The Contract May Be Regarded As Fraudulent And Render The Bidder Or Supplier Liable For Prosecution Subject To The Applicable Laws And Issuances.] 1. Heated Mechanical Grain Dryer-recirculating Batch Dryer *drying System 6 Tons Capacity With Programmable In-line Monitoring System With Control Panel Prime Mover: Electric Motor *heating System 1 Petroleum Based Fuel Flame Sensor Electronic Ignition System Automatic Fuel Shut-off Adjustable Fuel Vaporizer Elevated Non-corrosive And Heat Resistant Fuel Container At 200 Liters Capacity Prime Mover: Electric Motor Heating System 2 Biomass Fuel Heat Exchanger: Stainless/fire Tubes Burning Chamber: Made Of Refractory Bricks Temperature Control Prime Mover: Electric Motor Pre-cleaner Dust Collection System Generator Set Power Rating (kva): 25 Kva (minimum) Portable Handheld Moisture Meter Standard Heavy Duty Tools: Made Of Tempered Steel And Chrome Vanadium 1 Set Socket Wrench (no. 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 22, 23, 24, 27, 30, 32 Min.) 1 Set Open Wrench (no. 8, 10, 12, 14, 16, 18, 20, 22, 24 Min.) Electrical Plier: 200mm Screwdriver: Philips And Flatheld, 300mm Grease Gun: 250mm Mechanical Pliers: 200mm Heavy Duty Toolbox And Roll-up Tools Holder Vacuum Cleaner Fire Extinguisher Automatic Portable Bag/sack Closer/sewer Terms And Conditions: (for Post-qua) 3. Item Must Have With Valid Agricultural Machinery Testing And Evaluation Center (amtec) Test Result 11. Winning Bidder Must Have A Service Center And Should Have Available Spare Parts And Technicians Within Lloilo City Or Iloilo Province 13. Technical Specification Of The Items In Bidding Documents Must Be Prepared, Signed And Sealed By An Agricultural And Biosystem Engineer 14. Winning Bidder Must Have A Permit To Operate Issued By The Department Of Agriculture (da) - Bureau Of Agricultural And Biosystems Engineering (bafe) 15. Winning Bidder Must Have A Certificate Of Accreditation Issued By The Department Of Agriculture Philippine Council For Agriculture And Fisheries (da-pcaf) And The National Agricultural And Fisheries Machinery Assemblers, Manufacturers, Importers, Distributors And Dealers Accreditation And Classification (namdac) Board 16. Winning Bidder Must Have A Certificate Of Conformity Issued By Department Of Agriculture (dao- Bureau Of Agricultural And Fisheries Engineering (bafe) Terms & Conditions: (for Delivery) 1. The Item Must Be Delivered At Art Center, Nanga, Pototan, Iloilo 2. The Item Must Be Delivered Within 45 Days Upon Receipt Of Notice To Proceed (ntp) 4. Laminated Reflectorized Vinyl Sticker Of Morprogres And Province Of Iloilo *6 Inches Diameter (minimum) For The Province Of Iloilo *2 Feet By 6 Inches (minimum) Morpogres 5. With Complete Set Of Operation Manual For Drying Unit, Drying System, Electric Motor, Generator Set And Portable Handheld Moisture Meter Written In English/filipino/vernacular 6. Project Signage/marker 7. Brand Of Engine Offered Must Be Available In The Philippine Market For Atleast 15 Years 8. Winning Bidder Must Installed The Item At Specified Site For Free 9. Item Must Conducted For Test Run 10. Item Must Have A Warranty Period Of Atleast 1 Year From The Date Of Acceptance By The End-user/recipient/beneficiary 12. Winning Bidder Must Provide Training As To The Proper Operation Of The Item 17. Item Must Be Delivered At Its Best Best Quality And Condition 18. Winning Bidder Must Coordinate With The Provincial Agriculture Office- Agricultural Engineering Division Prior To The Delivery Of Item Listed Above ___________________________________ Signature Over Printed Name Section Viii. Checklist Of Technical And Financial Documents I. Technical Component Envelope Class “a” Documents Legal Documents ⬜ (a) Valid Philgeps Registration Certificate (platinum Membership) (all Pages); Or ⬜ (b) Registration Certificate From Securities And Exchange Commission (sec), Department Of Trade And Industry (dti) For Sole Proprietorship, Or Cooperative Development Authority (cda) For Cooperatives Or Its Equivalent Document, And ⬜ (c) Mayor’s Or Business Permit Issued By The City Or Municipality Where The Principal Place Of Business Of The Prospective Bidder Is Located, Or The Equivalent Document For Exclusive Economic Zones Or Areas; And ⬜ (d) Tax Clearance Per E.o. No. 398, S. 2005, As Finally Reviewed And Approved By The Bureau Of Internal Revenue (bir). Technical Documents ⬜ (e) Statement Of The Prospective Bidder Of All Its Ongoing Government And Private Contracts, Including Contracts Awarded But Not Yet Started, If Any, Whether Similar Or Not Similar In Nature And Complexity To The Contract To Be Bid; And ⬜ (f) Statement Of The Bidder’s Single Largest Completed Contract (slcc) Similar To The Contract To Be Bid, Except Under Conditions Provided For In Sections 23.4.1.3 And 23.4.2.4 Of The 2016 Revised Irr Of Ra No. 9184, Within The Relevant Period As Provided In The Bidding Documents; And ⬜ (g) Original Copy Of Bid Security. If In The Form Of A Surety Bond, Submit Also A Certification Issued By The Insurance Commission; Or Original Copy Of Notarized Bid Securing Declaration; And ⬜ (h) Conformity With The Technical Specifications, Which May Include Production/delivery Schedule, Manpower Requirements, And/or After-sales/parts, If Applicable; And ⬜ (i) Original Duly Signed Omnibus Sworn Statement (oss); And If Applicable, Original Notarized Secretary’s Certificate In Case Of A Corporation, Partnership, Or Cooperative; Or Original Special Power Of Attorney Of All Members Of The Joint Venture Giving Full Power And Authority To Its Officer To Sign The Oss And Do Acts To Represent The Bidder. Financial Documents ⬜ (j) The Supplier’s Audited Financial Statements, Showing, Among Others, The Supplier’s Total And Current Assets And Liabilities, Stamped “received” By The Bir Or Its Duly Accredited And Authorized Institutions, For The Preceding Calendar Year Which Should Not Be Earlier Than Two (2) Years From The Date Of Bid Submission; And ⬜ (k) The Prospective Bidder’s Computation Of Net Financial Contracting Capacity (nfcc); Or A Committed Line Of Credit From A Universal Or Commercial Bank In Lieu Of Its Nfcc Computation. Class “b” Documents ⬜ (l) If Applicable, A Duly Signed Joint Venture Agreement (jva) In Case The Joint Venture Is Already In Existence; Or Duly Notarized Statements From All The Potential Joint Venture Partners Stating That They Will Enter Into And Abide By The Provisions Of The Jva In The Instance That The Bid Is Successful. Ii. Financial Component Envelope ⬜ (m) Original Of Duly Signed And Accomplished Financial Bid Form; And ⬜ (n) Original Of Duly Signed And Accomplished Price Schedule(s). Other Documentary Requirements Under Ra No. 9184 (as Applicable) ⬜ (o) [for Foreign Bidders Claiming By Reason Of Their Country’s Extension Of Reciprocal Rights To Filipinos] Certification From The Relevant Government Office Of Their Country Stating That Filipinos Are Allowed To Participate In Government Procurement Activities For The Same Item Or Product. ⬜ (p) Certification From The Dti If The Bidder Claims Preference As A Domestic Bidder Or Domestic Entity.   Bid Form Date: _____________________ Bid No.: ___________________ To: Bids And Awards Committee Iloilo Provincial Government Iloilo Provincial Capitol Bonifacio Drive, Iloilo City Having Examined The Philippine Bidding Documents (pbds) Including The Supplemental Or Bid Bulletin Numbers __________, The Receipt Of Which Is Hereby Duly Acknowledged, We, The Undersigned, Offer To Supply/deliver/perform _________________________________________ [description Of The Goods] In Conformity With The Said Pbds For The Sum Of _______________________________________, (php _______________________) [total Bid Amount In Words And Figures] Or The Total Calculated Bid Price, As Evaluated And Corrected For Computational Errors, And Other Bid Modifications In Accordance With The Price Schedules Attached Herewith And Made Part Of This Bid. The Total Bid Price Includes The Cost Of All Taxes, Such As, But Not Limited To: Value Added Tax (vat), Income Tax, Local Taxes, And Other Fiscal Levies And Duties, As Applicable, Which Are Itemized Herein Or In The Price Schedules, If Our Bid Is Accepted, We Undertake: A. To Deliver The Goods In Accordance With The Delivery Schedule Specified In The Schedule Of Requirements Of The Philippine Bidding Documents (pbds); B. To Provide A Performance Security In The Form, Amounts, And Within The Times Prescribed In The Pbds; C. To Abide By The Bid Validity Period Specified In The Pbds And It Shall Remain Binding Upon Us At Any Time Before The Expiration Of That Period. Until A Formal Contract Is Prepared And Executed, This Bid, Together With Your Written Acceptance Thereof And Your Notice Of Award, Shall Be Binding Upon Us. We Understand That You Are Not Bound To Accept The Lowest Calculated Bid Or Any Bid You May Receive. We Certify/confirm That We Comply With The Eligibility Requirements Pursuant To The Pbds. The Undersigned Is Authorized To Submit The Bid On Behalf Of ____________________________________________________ As Evidenced By The Attached [name Of The Bidder] ______________________________________. [state The Written Authority]. We Acknowledge That Failure To Sign Each And Every Page Of This Bid Form, Including The Schedule Of Prices, Shall Be A Ground For The Rejection Of Our Bid. Name: Legal Capacity: Signature: Duly Authorized To Sign The Bid For And Behalf Of: Date: Republic Of The Philippines) City Of ____________________) S.s. Bid Securing Declaration Bid No.: ___________________________ To: Bids And Awards Committee Iloilo Provincial Government Iloilo Provincial Capitol Bonifacio Drive, Iloilo City I/we, The Undersigned, Declare That: 1. I/we Understand That, According To Your Conditions, Bids Must Be Supported By A Bid Security, Which May Be In The Form Of A Bid Securing Declaration. 2. I/we Accept That: (a) I/we Will Be Automatically Disqualified From Bidding For Any Procurement Contract With Any Procuring Entity For A Period Of Two (2) Years Upon Receipt Of Your Blacklisting Order; And, (b) I/we Will Pay The Applicable Fine Provided Under Section 6 Of The Guidelines On The Use Of Bid Securing Declaration, Within Fifteen (15) Days From Receipt Of The Written Demand By The Procuring Entity For The Commission Of Acts Resulting To The Enforcement Of The Bid Securing Declaration Under Sections 23.1(b), 34.2, 40.1 And 69.1, Except 69.1(f),of The Irr Of Ra No. 9184; Without Prejudice To Other Legal Action The Government May Undertake. 3. I/we Understand That This Bid Securing Declaration Shall Cease To Be Valid On The Following Circumstances: A. Upon Expiration Of The Bid Validity Period, Or Any Extension Thereof Pursuant To Your Request; B. I Am/we Are Declared Ineligible Or Post-disqualified Upon Receipt Of Your Notice To Such Effect, And (i) I/we Failed To Timely File A Request For Reconsideration Or (ii) I/we Filed A Waiver To Avail Of Said Right; And C. I Am/we Are Declared The Bidder With The Lowest Calculated Responsive Bid, And I/we Have Furnished The Performance Security And Signed The Contract. In Witness Whereof, I/we Have Hereunto Set My/our Hand/s This ______ __ At ___________________________. _________________________________________________ [signature Over Printed Name Of Bidder Or Its Authorized Representative] [insert Signatory’s Legal Capacity] Subscribed And Sworn To Before Me, _______________________ In The _____________________. Affiant Exhibited To Me His Valid Identification Card With Id No. _________________ Issued By: ___________________. Doc No.:______; Page No. _____; Book No.:_____; Series Of: _____; Republic Of The Philippines) City Of _____________________) S.s. Omnibus Sworn Statement (for Sole Proprietorship) I, _______________________________________of Legal Age, Single/married/widow, Filipino, And Residing At ________________________________________, Philippines, After Having Been Duly Sworn In Accordance With Law, Do Hereby Depose And State That: 1. I Am The Sole Proprietor Or Authorized Representative Of ______________________________________ With Office Address At ______________________________________; 2. As The Owner And Sole Proprietor, Or Authorized Representative Of _____________________________________, I Have Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For ___________________________________________ [name Of The Project] Of The Iloilo Provincial Government, As Shown In The Attached Duly Notarized Special Power Of Attorney; 3. __________________________________________ Is Not “blacklisted” Or Barred From Bidding By The Government Of The Philippines Or Any Of Its Agencies, Offices, Corporations, Or Local Government Units, Foreign Government/foreign Or International Financing Institution Whose Blacklisting Rules Have Been Recognized By The Government Procurement Policy Board, By Itself Or By Relation, Membership, Association, Affiliation, Or Controlling Interest With Another Blacklisted Person Or Entity As Defined And Provided For In The Uniform Guidelines On Blacklisting; 4. Each Of The Documents Submitted In Satisfaction Of The Bidding Requirements Is An Authentic Copy Of The Original, Complete, And All Statements And Information Provided Therein Are True And Correct; 5. __________________________________________ Is Authorizing The Head Of The Procuring Entity Or Its Duly Authorized Representative(s) To Verify All The Documents Submitted; 6. The Owner Or Sole Proprietor Is Not Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; 7. ___________________________________________ Complies With Existing Labor Laws And Standards; And 8. ___________________________________________ Is Aware Of And Has Undertaken The Responsibilities As A Bidder In Compliance With The Philippine Bidding Documents, Which Includes: A. Carefully Examining All Of The Bidding Documents; B. Acknowledging All Conditions, Local Or Otherwise, Affecting The Implementation Of The Contract; C. Making An Estimate Of The Facilities Available And Needed For The Contract To Be Bid, If Any; And D. Inquiring Or Securing Supplemental/bid Bulletin(s) Issued For The ______________________________________. [name Of The Project] 9. _________________________________________ Did Not Give Or Pay Directly Or Indirectly, Any Commission, Amount, Fee, Or Any Form Of Consideration, Pecuniary Or Otherwise, To Any Person Or Official, Personnel Or Representative Of The Government In Relation To Any Procurement Project Or Activity. 10. In Case Advance Payment Was Made Or Given, Failure To Perform Or Deliver Any Of The Obligations And Undertakings In The Contract Shall Be Sufficient Grounds To Constitute Criminal Liability For Swindling (estafa) Or The Commission Of Fraud With Unfaithfulness Or Abuse Of Confidence Through Misappropriating Or Converting Any Payment Received By A Person Or Entity Under An Obligation Involving The Duty To Deliver Certain Goods Or Services, To The Prejudice Of The Public And The Government Of The Philippines Pursuant To Article 315 Of Act No. 3815 S. 1930, As Amended, Or The Revised Penal Code. In Witness Whereof, I/we Have Hereunto Set My/our Hand/s This ______ __ At ___________________________. ________________________________________________ [signature Over Printed Name Of Bidder Or Its Authorized Representative] [insert Signatory’s Legal Capacity] Subscribed And Sworn To Before Me, _______________________ In The _____________________. Affiant Exhibited To Me His Valid Identification Card With Id No. _________________ Issued By: ___________________. Doc No.:______; Page No. _____; Book No.:_____; Series Of: _____; Republic Of The Philippines) City Of ____________________) S.s. Omnibus Sworn Statement (for A Partnership Or Cooperative) I, _______________________________________of Legal Age, Single/married/widow, Filipino, And Residing At ________________________________________, Philippines, After Having Been Duly Sworn In Accordance With Law, Do Hereby Depose And State That: 1. I Am The Duly Authorized And Designated Representative Of ______________________________ With Office Address At ___________________________________; 2. I Am Granted Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For __________________________________ Of The Iloilo Provincial Government, As Shown [name Of The Project] In The Attached _________________________________________________; [state Title Of Attached Document Showing Proof Of Authorization (e.g., Duly Notarized Secretary’s Certificate, Board/partnership Resolution, Or Special Power Of Attorney, Whichever Is Applicable;] 3. _____________________________________ Is Not “blacklisted” Or Barred From Bidding By The Government Of The Philippines Or Any Of Its Agencies, Offices, Corporations, Or Local Government Units, Foreign Government/foreign Or International Financing Institution Whose Blacklisting Rules Have Been Recognized By The Government Procurement Policy Board, By Itself Or By Relation, Membership, Association, Affiliation, Or Controlling Interest With Another Blacklisted Person Or Entity As Defined And Provided For In The Uniform Guidelines On Blacklisting; 4. Each Of The Documents Submitted In Satisfaction Of The Bidding Requirements Is An Authentic Copy Of The Original, Complete, And All Statements And Information Provided Therein Are True And Correct; 5. _____________________________________ Is Authorizing The Head Of The Procuring Entity Or Its Duly Authorized Representative(s) To Verify All The Documents Submitted; 6. None Of The Officers And Members Of _____________________________________ Is Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; 7. _____________________________________ Complies With Existing Labor Laws And Standards; And 8. _____________________________________ Is Aware Of And Has Undertaken The Responsibilities As A Bidder In Compliance With The Philippine Bidding Documents, Which Includes: A. Carefully Examining All Of The Bidding Documents; B. Acknowledging All Conditions, Local Or Otherwise, Affecting The Implementation Of The Contract; C. Making An Estimate Of The Facilities Available And Needed For The Contract To Be Bid, If Any; And D. Inquiring Or Securing Supplemental/bid Bulletin(s) Issued For The ______________________________________. [name Of The Project] 9. _____________________________________ Did Not Give Or Pay Directly Or Indirectly, Any Commission, Amount, Fee, Or Any Form Of Consideration, Pecuniary Or Otherwise, To Any Person Or Official, Personnel Or Representative Of The Government In Relation To Any Procurement Project Or Activity. 10. In Case Advance Payment Was Made Or Given, Failure To Perform Or Deliver Any Of The Obligations And Undertakings In The Contract Shall Be Sufficient Grounds To Constitute Criminal Liability For Swindling (estafa) Or The Commission Of Fraud With Unfaithfulness Or Abuse Of Confidence Through Misappropriating Or Converting Any Payment Received By A Person Or Entity Under An Obligation Involving The Duty To Deliver Certain Goods Or Services, To The Prejudice Of The Public And The Government Of The Philippines Pursuant To Article 315 Of Act No. 3815 S. 1930, As Amended, Or The Revised Penal Code. In Witness Whereof, I/we Have Hereunto Set My/our Hand/s This ______ __ At ___________________________. _________________________________________________ [signature Over Printed Name Of Bidder Or Its Authorized Representative] [insert Signatory’s Legal Capacity] Subscribed And Sworn To Before Me, _______________________ In The _____________________. Affiant Exhibited To Me His Valid Identification Card With Id No. _________________ Issued By: ___________________. Doc No.:______; Page No. _____; Book No.:_____; Series Of: _____; Republic Of The Philippines) City Of _____________________) S.s. Omnibus Sworn Statement (for A Corporation Or Joint Venture) I, _______________________________________of Legal Age, Single/married/widow, Filipino, And Residing At ________________________________________, Philippines, After Having Been Duly Sworn In Accordance With Law, Do Hereby Depose And State That: 1. I Am The Duly Authorized And Designated Representative Of ______________________________ With Office Address At ___________________________________; 2. I Am Granted Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For __________________________________ Of The Iloilo Provincial Government, As Shown [name Of The Project] In The Attached _________________________________________________; [state Title Of Attached Document Showing Proof Of Authorization (e.g., Duly Notarized Secretary’s Certificate, Board/partnership Resolution, Or Special Power Of Attorney, Whichever Is Applicable;] 3. _____________________________________ Is Not “blacklisted” Or Barred From Bidding By The Government Of The Philippines Or Any Of Its Agencies, Offices, Corporations, Or Local Government Units, Foreign Government/foreign Or International Financing Institution Whose Blacklisting Rules Have Been Recognized By The Government Procurement Policy Board, By Itself Or By Relation, Membership, Association, Affiliation, Or Controlling Interest With Another Blacklisted Person Or Entity As Defined And Provided For In The Uniform Guidelines On Blacklisting; 4. Each Of The Documents Submitted In Satisfaction Of The Bidding Requirements Is An Authentic Copy Of The Original, Complete, And All Statements And Information Provided Therein Are True And Correct; 5. _____________________________________ Is Authorizing The Head Of The Procuring Entity Or Its Duly Authorized Representative(s) To Verify All The Documents Submitted; 6. None Of The Officers, Directors, And Controlling Stockholders Of _____________________________________is Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; 7. _____________________________________ Complies With Existing Labor Laws And Standards; And 8. _____________________________________ Is Aware Of And Has Undertaken The Responsibilities As A Bidder In Compliance With The Philippine Bidding Documents, Which Includes: E. Carefully Examining All Of The Bidding Documents; F. Acknowledging All Conditions, Local Or Otherwise, Affecting The Implementation Of The Contract; G. Making An Estimate Of The Facilities Available And Needed For The Contract To Be Bid, If Any; And H. Inquiring Or Securing Supplemental/bid Bulletin(s) Issued For The ______________________________________. [name Of The Project] 9. _____________________________________ Did Not Give Or Pay Directly Or Indirectly, Any Commission, Amount, Fee, Or Any Form Of Consideration, Pecuniary Or Otherwise, To Any Person Or Official, Personnel Or Representative Of The Government In Relation To Any Procurement Project Or Activity. 10. In Case Advance Payment Was Made Or Given, Failure To Perform Or Deliver Any Of The Obligations And Undertakings In The Contract Shall Be Sufficient Grounds To Constitute Criminal Liability For Swindling (estafa) Or The Commission Of Fraud With Unfaithfulness Or Abuse Of Confidence Through Misappropriating Or Converting Any Payment Received By A Person Or Entity Under An Obligation Involving The Duty To Deliver Certain Goods Or Services, To The Prejudice Of The Public And The Government Of The Philippines Pursuant To Article 315 Of Act No. 3815 S. 1930, As Amended, Or The Revised Penal Code. In Witness Whereof, I/we Have Hereunto Set My/our Hand/s This ______ __ At ___________________________. ________________________________________________ [signature Over Printed Name Of Bidder Or Its Authorized Representative] [insert Signatory’s Legal Capacity] Subscribed And Sworn To Before Me, _______________________ In The _____________________. Affiant Exhibited To Me His Valid Identification Card With Id No. _________________ Issued By: ___________________. Doc No.:______; Page No. _____; Book No.:_____; Series Of: _____; Republic Of The Philippines) City Of ____________________) S.s. Performance Securing Declaration Bid No: ____________________ To: Bids And Awards Committee Iloilo Provincial Government Iloilo Provincial Capitol Bonifacio Drive, Iloilo City I/we, The Undersigned, Declare That: 1. I/we Understand That, According To Your Conditions, To Guarantee The Faithful Performance By The Supplier/distributor/manufacturer/contractor/consultant Of Its Obligations Under The Contract, I/we Shall Submit A Performance Securing Declaration Within A Maximum Period Of Ten (10) Calendar Days From The Receipt Of The Notice Of Award Prior To The Signing Of The Contract. 2. I/we Accept That: I/we Will Be Automatically Disqualified From Bidding For Any Procurement Contract With Any Procuring Entity For A Period Of One (1) Year For The First Offense, Or Two (2) Years For The Second Offense, Upon Receipt Of Your Blacklisting Order If I/we Have Violated My/our Obligations Under The Contract; 3. I/we Understand That This Performance Securing Declaration Shall Cease To Be Valid Upon: A. Issuance By The Procuring Entity Of The Certificate Of Final Acceptance, Subject To The Following Conditions: I. Procuring Entity Has No Claims Filed Against The Contract Awardee; Ii. It Has No Claims For Labor And Materials Filed Against The Contractor; And Iii. Other Terms Of The Contract; Or B. Replacement By The Winning Bidder Of The Submitted Psd With A Performance Security In Any Of The Prescribed Forms Under Section 39.2 Of The 2016 Revised Irr Of Ra No. 9184 As Required By The End-user. In Witness Whereof, I/we Have Hereunto Set My/our Hand/s This ______ __ At ___________________________. _________________________________________________ [signature Over Printed Name Of Bidder Or Its Authorized Representative] [insert Signatory’s Legal Capacity] Subscribed And Sworn To Before Me, _______________________ In The _____________________. Affiant Exhibited To Me His Valid Identification Card With Id No. _________________ Issued By: ___________________. Doc No.:______; Page No. _____; Book No.:_____; Series Of: _____; Email Address: ______________________________________ Statement Of Single Largest Completed Contract (slcc) Similar To The Contract To Be Bid Bidder’s Name: Email Address: Bidder’s Address: Fax Number: Tel. Number: Name Of Project Amount Of Contract Date Of Contract Effectivity Owner’s Name And Address Delivery Period Date Of Delivery Date Of Acceptance Signature Over Printed Name Attachments: 1. Purchase Order (po) 2. Acceptance And Inspection Report (air) Statement Of All On-going Government And Private Contracts (including Contracts Awarded But Not Yet Started, If Any, Whether Similar Or Not Similar In Nature And Complexity To The Contract To Be Bid) Bidder’s Name: Email Address: Bidder’s Address: Fax Number: Tel. Number: Name Of Project/s Amount Of Contract Date Of Contract Effectivity Owner’s Names And Address Delivery Period (indicate All Delivery Periods If Staggered Delivery Allowed) End Of Delivery Period Value Of Outstanding Contracts (indicate If Partial Delivery Allowed) No. Of Days From End Of Delivery Period Days Of Approved Extension/ Suspension, If Any Total Value Of Outstanding Contracts (php) Signature Over Printed Name Fill Up All The Columns Accordingly Disclaimer: Non-disclosure Of All On-going Contracts And Details Thereof Is Grounds For Ineligibility And Disqualification.

Details: Description Invitation To Bid Pb-01-2025 Supply And Delivery Of Technical Vocational Livelihood (tvl) Equipment Packages For Public Senior High Schools 1. The Department Of Education, Schools Division Of Ilocos Sur Through The Republic Act No. 11975 – Fy 2024 Gaa (sub-allotment Release Order No. Roi-24-1175) Intends To Apply The Sum Of Two Million Three Hundred Thirty Six Thousand Two Hundred Eighty Pesos (p2,336,280.00) Being The Approved Budget For The Contract (abc) To Payments Under The Contract For The Project Supply And Delivery Of Vocational Livelihood (tvl) Equipment Packages For Public Senior High Schools. Bids Received Higher Than The Abc Shall Be Automatically Rejected At Bid Opening. Item No. Project Description Qty. Unit Unit Cost Abc For The Project (in Php) Tvl Tools & Equipment (bread And Pastry Production) 1 Air Compressor With Airbrush Cake Decorating Set (medium) Pc 1 2,414.00 2,414.00 2 Beater (standard) Pc 6 287.00 1,722.00 3 Board, Chopping, 6 Color Rectangular Material: Plastic (polypropylene), Food Grade Board Size: Length: 38 Cm (minimum) Width: 30 Cm (minimum) Thickness: 1.27 Cm (minimum) Color-coded For Use With Different Types Of Food, Blue, Red, Yellow, Green, Brown And White, Preferably Packed In Set Set 6 920.00 5,520.00 4 Boiler, Double (material: Stainless Steel Thickness: 1/16 Inch (1.5 Mm) (minimum) Lid Material: Glass Riveted Handle On Both Side Diameter: 9 1/2 Inches (minimum) Total Height: 9.4 Inches (minimum) Inset Bottom Diameter: 9 Inches (minimum) Inset Top Diameter: 9 Inches (minimum) Capacity: 2 Liters (minimum) Must Be A Set Which Includes One (1) Saucepan, One (1) Boiler, And One (1) Lid With Stainless Steel Handle And Smooth Surfaces With No Sharp Edges) Set 1 1,955.00 1,955.00 5 Bowl, Mixing (6 Pcs/set) Pc 12 2,415.00 28,980.00 6 Cake Pans, Round #4, #6, #8, #10, #12, #14, #16 Pc 6 1,725.00 10,350.00 7 Cake Stand, With Tier (type: Cake Stand With Tier, Food Grade Body Shape: Circular With 3 Tiers Material: Hard Plastic, Polypropylene, 4 Mm Thick The Tier Consists Of The Following Sizes: Tier 1: 18 Cm Diameter (minimum) Tier 2: 25 Cm Diameter (minimum) Tier 3: 30 Cm Diameter (minimum) Column Diameter: 20 To 30 Mm (solid) Distance Between Tiers: 15 Cm Over-all Length: 30 Cm (minimum) Pc 6 1,725.00 10,350.00 8 Cake Turn Table (body Shape: Circular Material: Cast Aluminum Plate. And Cast-iron Base Upper Plate: 30 Cm Diameter (minimum) And 1.4 Cm Thickness (minimum) Base Dimensions: 18 Cm (minimum); 1.4 Cm Thickness (minimum) Total Height: 10 Cm To 15 Cm) Pc 3 1,265.00 3,795.00 9 Coupler (tubular Material: Hard Plastic, Polypropylene, Any Bright Color Height: 3cm (minimum) Top Diameter: 1.27 Cm (minimum) Bottom Diameter: 2.54 Cm (minimum) Preferably With Storage Case) Pc 13 207.00 2,691.00 10 Cup, Measuring (for Solid) The Standard 4 Measuring Cup Sizes Are: 1 Cup, 1/2 Cup, 1/3 Cup And 1/4 Cup Set 12 977.00 11,724.00 11 Cup, Measuring, 250 Ml For Liquid Pc 12 632.00 7,584.00 12 Cup, Measuring, 500ml For Liquid Pc 12 747.00 8,964.00 13 Cutter, Dough (stainless Steel Straight Blade With Stainless Steel Handle Blade Dimension: Length: 15 Cm X Width: 11 Cm X Thickness: 1.2mm(minimum) Handle Dimension: Length: 15 Cm X Diameter: 3 Cm (minimum) Preferably With Packing Case Food Grade And Dishwasher Safe Design Allows Item To Be Hung For Storage) Pc 1 402.00 402.00 14 Cutter, Pie (medium) Pc 6 460.00 2,760.00 15 Flour Sifter, Hand Cranked (standard) Round Shape Material: Stainless Steel Dimension: Diameter: 133.3 Mm (minimum) X Height: 165 Mm (minimum) Thickness: 0.79 Mm (minimum) (body) And Constructed With Stainless Steel Wire Mesh #30 Bottom Volume Markings Should Be Seen Inside And Outside Of The Sifter Capacity: 5 Cups (1.18 Liter) Pc 6 747.00 4,482.00 16 Grater 4 Sided (s) Pc 6 402.00 2,412.00 17 Knife, Kitchen (s) Pc 6 747.00 4,482.00 18 Knife, Pallet (s) Pc 6 573.00 3,438.00 19 Ladle, 3 0z Pc 6 241.00 1,446.00 20 Loaf Pan Big Pc 6 862.00 5,172.00 21 Loaf Pan, Medium Pc 6 517.00 3,102.00 22 Loaf Pan, Small Pc 6 126.00 756.00 23 Muffin Pan, Big Pc 6 448.00 2,688.00 24 Muffin Pan, Medium Pc 6 414.00 2,484.00 25 Muffin Pan, Small Pc 6 322.00 1,932.00 26 Pie Pan, 10 Inches Diameter Pc 6 517.00 3,102.00 27 Pie Pan, # 6, #8, #10 Set 6 1,265.00 7,590.00 28 Pillars, Cake (big) Pc 6 517.00 3,102.00 29 Piping Bag (100 Pcs Per Pack) (m) Pack 25 241.00 6,025.00 30 Rectangular Pan, (7” X 11”) Pc 4 263.00 1,052.00 31 Rolling Pins (3cm X 10 Cm) Pc 12 402.00 4,824.00 32 Rubber Scraper (m) Pc 12 207.00 2,484.00 33 Sauce Pan 22cm Pc 13 632.00 8,216.00 34 Sheet Pan (m) Pc 15 517.00 7,755.00 35 Spoon, Measuring (plastic) ¼ Teaspoon, ½ Teaspoon, 1 Teaspoon, And 1 Tablespoon Set 26 287.00 7,462.00 36 Spoon, Wooden (s) Pc 15 92.00 1,380.00 37 Strainer Stainless (m) Pc 15 212.00 3,180.00 38 Tip, Decorating X 24 (small To Large) Set 23 632.00 14,536.00 39 Weighing Scale, 10 Kgs (digital) Pc 13 2,875.00 37,375.00 40 Weighing Scale,5 Kgs, (digital) Pc 13 1,265.00 16,445.00 41 Wire Whisk, Medium Ballon Material: Heavy Duty Stainless Steel Dimensions (l X W): 31.8 Cm X 7.6 Cm (minimum) Handle Length: 12 Cm (minimum) With Hanging Loop No. Of Wires: 8 Wires Wire Diameter: 2 Mm (minimum) Preferably With A Packing Case Pc 13 286.00 3,718.00 Sub Total 259,851.00 Tvl Tools & Equipment (computer System Servicing) 42 Allen Wrench (set Of 10 Pieces: 1.5 Mm, 2 Mm, 2.5 Mm, 3 Mm, 4 Mm, 5 Mm, 5.5 Mm, 6 Mm, 8 Mm, 10 Mm;) Set 50 450.00 22,500.00 43 Anti-static Device (anti-static Wrist Strap) Adjustable And Elastic Wristband With Integrated 1 Mega Ohm Resistor Pc 50 250.00 12,500.00 44 Combination Pliers, 8" Pc 50 350.00 17,500.00 45 Crimping Tool (rj 11/45) Pc 52 450.00 23,400.00 46 Desoldering Pump (plastic Or Aluminum Housing) Pc 52 250.00 13,000.00 47 Electric Drill, Portable (rated Voltage: 220 / 240 Volts, Ac 60 Hz Power In Watts: 550 To 650 Watts) Pc 4 4,000.50 16,002.00 48 External Optical Drive Cd-r Dvd-r (interface: Usb 3.0 Or Better; 2. Compatibility: Windows 2000, Xp, Vista, 7, 8, 10, Apple Mac, Linux Or Better; 3. Read Speed: At Least 8x Dvd, At Least 24x Cd; 4. Write Speed: At Least 4x Dvd, At Least 16x Cd) Pc 6 1,000.00 6,000.00 49 Flash Drive (1tb) Pc 52 850.00 44,200.00 50 Flashlight, Head-mounted (rechargeable) Minimum Of 160 Lumens; Beam Distance: Minimum Of 150 Meters; Includes 220 V Ac Charger/power Adaptor (or Equivalent) Pc 50 550.00 27,500.00 51 Hub / Switch ( Standards And Protocols: Ieee 802.3, Ieee802.3u, Ieee802.3x Csma/cd Interface: 8 10/100mbps Ports, Auto-negotiation, Auto-mdi/mdix External Power Supply Adapter: 100-240vac,50/60hz Fanless Data Rates: 10/100mbps At Half Duplex; 20/200mbps At Full Duplex Led Indicator: Power, 1, 2, 3, 4, 5, 6, 7, 8 Dimensions: 5.3 X 3.1 X 0.9 In. (134.5 X 79 X 22.5mm) (approx.) Pc 42 2,000.00 84,000.00 52 Lan Cable Tester (1. Package Contents: 8-port 10/100mbps Desktop Switch, Power) Pc 50 252.00 12,600.00 53 Long Nose Pliers, 8" Pc 50 200.00 10,000.00 54 Multimeter, Digital (auto Range/data Hold/back Light/ Led Lamp/diode Test/triode Test/continuity/ Overload Protection/low Battery Indication/auto Power Off/short-circuit Protection. Display: True Rms, 6000 Counts, 3 5/6 Digits Overload Display: Display Ol Dc Voltage:600mv/6v/60v/600v(0.5%+3), 1000v (0.5%+3) Ac Voltage:600mv/6v/60v/600v/750v (0.8%+5) Dc Current:600a/6000a/60ma/600ma/10a (1.2%+3) Ac Current:600a/6000a/60ma/600ma/10a (1.5%+3) Resistance:600/6k/60k/600k/(1.0%+3) ,6m/60m (1.5%+3) Capacitance: 10nf/100nf/1000nf/10uf/100uf/1000uf (4.0%+5), 10mf/100mf(5.0%+5 Pc 40 800.00 32,000.00 55 Patch Panel (48 Ports) Cat6 Cable Material: Abs Plastic Application: Utp(unshielded) Certification: Rohs, Iso, Ce Rj45 Connector: Two Rows (1-24 Ports & 25-48 Ports) Transport Package: 1pcs/box Pc 50 2,500.00 125,000.00 56 Pc Video Camera (5.0 Mega Pixel Web Camera, Usb-type; With Microphone For Laptop And Desktop Pc Use; Resolution: At Least 640 X 480; Support Windows Xp/7/8/equivalent Mac Os Or Later Versions) Pc 20 500.00 10,000.00 57 Phillip’s Screwdriver, 8" Insulated Pc 50 250.00 12,500.00 58 Precision Screwdriver Set (1 Set Comes With The Following: 3 X Phillips Tip No. 00, 0, And 1; 6 X Standard Tip No. 1, 1.2, 1.4, 1.8, 2.4, And 3.0; 1 X Awl; 1 X Magnet; Plastic Storage Case;) Set 50 500.00 25,000.00 59 Soldering Iron, 60w Pc 50 250.00 12,500.00 60 Standard Screwdriver (flat), 8” Insulated Pc 50 250.00 12,500.00 61 Uninterruptible Power Supply (ups) Battery (included): Lithium-ion Battery Or Maintenance-free Sealed Lead-acid Battery With Suspended Electrolyte: Leakproof Voltage: Nominal Input Voltage: 230v, 50/60hz Output Power Capacity: 600va (minimum) Pc 40 4,000.00 160,000.00 62 Usb External Hd 1tb Pc 10 3,500.00 35,000.00 63 Wire Stripper (10 Awg To 24 Awg Length: 7 Inches (minimum) Pc 54 250.00 13,500.00 64 Wireless Access Point ( Access Point Dual Band Wi-fi Band / Data Transfer Rate: 867 Mbps At 5 Ghz And 300 Mbps At 2.4ghz Band Operating Modes: Access Point (ap), Bridge, Wireless Client, Repeater Interface: One 10/100m Ethernet Port(rj45), Support Passive Poe Power On/off Button And Reset Button Comes With External Power Supply: 5vdc-12vdc / 0.5a-1.0a Dimensions ( L X W X D ): (76-191 ×47-125 ×30-68mm) Pc 50 1,500.00 75,000.00 Subtotal 802,202.00 Tvl Tools & Equipment (cookery) 65 Apple Corer (material: Stainless Steel Total Length: 18 Cm (minimum) Handle Material: Hard Plastic, Polypropylene Handle Dimension: Length-10 Cm X Diameter-2 Cm (minimum) Blade Size: Length-8cm X Diameter-2 Cm (minimum) Pc 10 444.00 4,440.00 66 Bain Marie, Table ( Type: Bain Marie Table (food Warmer) Body Shape: Rectangular Material: 304 Stainless Steel, 0.8 Mm Thick (minimum) Dimensions: Length-1500 Mm X Width-700mm X Height-800 Mm (minimum) Power Source: Voltage: 220 Volts - 230 Volts, 50 Hz/ 60hz With Royal Cord 1.5 Meter Long With Attachment Standard Type A Male Plug Or Provide Plug Adopter 10a/220v) Pc 4 20,700.00 82,800.00 67 Blender, Electric (material Housing: Plastic (polypropylene) Jar Height: 25 Cm To 28 Cm Jar Thickness: 4 Mm To 8 Mm Heat Resistant Glass Jar With Cover Source Voltage: 220volts/ 240volts, 50hz/ 60hz With Power Cord 1.5 Meter Long With Attachment Of Standard Type A Male Plug Or Provide Plug Adopter 10a/220v. Power Wattage: 300 To 700 Watts Blade: Stainless Steel, 3 To 4 Metal Blades) Pc 4 2,875.00 11,500.00 68 Board, Chopping/cutting, Plastic (board Size: Length: 15 Inches (minimum) Width: 12 Inches (minimum) Thickness: 0.5 Inch (minimum) Pc 20 289.00 5,780.00 69 Boiler, Double (stainless Steel Thickness: 1/16 Inch (1.5 Mm) (minimum) Lid Material: Glass Riveted Handle On Both Sides Diameter: 9 1/2 Inches (minimum) Total Height: 9.4 Inches (minimum) Inset Bottom Diameter: 9 Inches (minimum) Inset Top Diameter: 9 Inches (minimum) Capacity: 3 Liters (minimum) Pc 2 2,128.00 4,256.00 70 Braising Pan, Medium Pc 10 1,494.00 14,940.00 71 Can Opener (stainless Steel Dimension: Length-21 Cm X Width 10 Cm X Depth:2.5cm (minimum) Pc 4 242.00 968.00 72 Casserole, Medium Pc 10 702.00 7,020.00 73 Casserole, Small Pc 12 669.00 8,028.00 74 Colander, Medium Pc 10 340.00 3,400.00 75 Colander, Small Pc 10 303.00 3,030.00 76 Cup, Measuring (for Solid) (cup, 1/2 Cup, 1/3 Cup, 1/4 Cup And 1/8 Cup.) Set 10 518.00 5,180.00 77 Dispenser, Paper Towel (abs Plastic Dimensions: Length =260 Mm X Width =100 Mm X Height = 211 Mm (minimum) Capacity: 200 Paper Paper Size: Length-20 Cm X Width- 8 Cm (approximate) Pc 10 403.00 4,030.00 78 Stand Fan, Electric (metal, Plastic Size/diameter: 18 Inches Power Rating: 70 Watts (minimum), 220/240 Vac, 50 / 60 Hz, Single Phase Rotation Angle: 90 Degrees Base: Stable, 16 Inches Diameter (approx.) Pc 5 1,495.00 7,475.00 79 Fire Extinguisher (with Contents) Capacity 5 - 6 Kgs Rechargeable Cylinder Metal Working Pressure Of Cylinder : 400 Psi Pc 1 2,875.00 2,875.00 80 Fish Poacher, Medium (oval Pot For Poaching Material: Stainless Steel, 0.64 Mm Thick Dimensions (l X W X D): 45 Cm X 15 Cm X 12cm (minimum) Handle Material: Stainless Steel Riveted Looped Handles On Both Side, 7 Cm (minimum) Handle Diameter: 8 Mm To 10 Mm) Pc 10 2,076.00 20,760.00 81 Fork, Carving (square Shape Prong Prong Material: High Carbon Stainless Steel Overall Length: 30 Cm (minimum) Blade Dimension: Length- 15 Cm X Width- 0.5 Cm X Thickness- 0.3 Cm (minimum) Number Of Prongs: 2 Prongs Comes With Square - Shaped Prongs And Pointed Tips Abs Plastic Triple-riveted Handle) Pc 10 593.00 5,930.00 82 Fork, Kitchen (body Shape: Standard Material: Stainless Steel Dimension: Length - 32 Cm X Width- 3.5 Cm (minimum) Fork Size: Length: 8 Cm X Width -3.5 Cm (minimum) Handle: Abs Plastic Number Of Tines: 2 Tines With Tapered End Pc 10 248.00 2,480.00 83 Frying Pan, Large Pc 10 438.00 4,380.00 84 Frying Pan, Medium Pc 10 334.00 3,340.00 85 Frying Pan, Small Pc 12 296.00 3,552.00 86 Funnel, S/s, Medium Pc 10 242.00 2,420.00 87 Funnel, S/s, Small Pc 10 207.00 2,070.00 88 Garbage Bin (material: Hard Plastic, Polypropylene Dimension: Diameter-26 Cm X Height-47 Cm (minimum) Capacity: 4 Gallons (minimum) Removable Dome Shape Lid With Spring Return Swivel) Pc 4 863.00 3,452.00 89 Glass Rack (body Shape: Square Material: Polypropylene Plastic Overall Dimensions: Length - 19 1/2 Inches X Width - 19 1/2 Inches X Height - 4 Inches (minimum) Compartments: Full-size 25 Individual Compartment Glass Rack Compartment Dimensions: Length - 3 ½ Inches X Width - 3 1/2 Inches X Height - 4 Inches (minimum) Easy Grip Handles Molded Into All Four Sides Preferably With A Packing Case ) Pc 12 817.00 9,804.00 90 Ice Cream Scooper (medium) Pc 2 288.00 576.00 91 Knife, Boning (28 Cm (minimum) Blade: Length-15 Cm X Width- 3 Cm (minimum), Pointed Tip Cutting Edge Angle From Tip To The Heel Is 13 To 14 Degrees Handle Length: 12 Cm (minimum) Handle Material: Hard Plastic Handle With Rivets) Pc 10 564.00 5,640.00 92 Knife, Chef (chef's Knife Body Shape: Flat Materials: Stainless Steel Overall Length: 30 Cm (minimum) Blade Size: Length - 20 Cm X Width-4 Cm (minimum) Blade Thickness: 2.5 Mm (minimum) Pc 10 449.00 4,490.00 93 Knife, Cleaver (forged Stainless Steel Heavy Duty Blade Length: 17 Cm (minimum) Overall Length: 30 Cm (minimum Cutting Edge: Straight Handle Material: Ergonomic Wood Handle With Triple Rivets) Pc 10 552.00 5,520.00 94 Knife, Oyster (stainless Steel Blade Dimension: Length - 7 Cm (minimum) X Width - 2 Cm (minimum) Blade Thickness: 2 Mm (minimum) Handle Material: Smooth Wooded Handle Rounded Handle Size: Length-10 Cm X Diameter- 3.5 Cm (minimum) Total Length (from The Tip Of The Handle Up To Tip Of The Blade) :17 Cm (minimum) Pc 10 547.00 5,470.00 95 Light, Emergency (metal, Anti-rust Coated Duration Time (2 Heads): 5 Hours (minimum) Automatically Light Up During Power Outage Overcharge And Over- Discharge Protection Built - In Ac Charger, Power Cord Plug To Adapt Type A Outlet (or Providing 5a Minimum Plug Adapter Is An Option) Battery Test Switch - External Safety Fuse Head: White Led 1w (minimum) 3.5 " Dome Reflector ) Pc 1 2,013.00 2,013.00 96 Meat Slicer (die Cast Aluminum Alloy And Body Painted Dimensions: Width-40.5 Cm X Depth- 45.7 Cm X Height- 38 Cm (minimum) Stainless Steel Rotary Blade Diameter: 190 Mm (minimum) Power Source: 220 Volts-230 Volts, 60 Hz With Power Cord 1.5 Meter Long With Attachment Of Standard Type A Male Plug Or Provide Plug Adopter 10a/220v) Pc 10 3,220.00 32,200.00 97 Pastry Tube (standard) Pc 10 633.00 6,330.00 98 Peeler, Y-type (stainless Steel Overall Dimensions (l X W X H): 7 Inches X 2 1/4 Inches X 1 Inch (minimum) Blade Material: 304 Stainless Steel, 0.7 Mm Head Dimension: (l X W X H) 2 1/4 Inches X 2 1/4 Inches X 1 Inch (minimum) Pc 10 275.00 2,750.00 99 Pepper And Salt Mill (round Body Material: Wood Size: Diameter: 5 Cm X Height: 20 Cm (minimum) Carved Of Wood With Stainless Steel Grinding Mechanism Color: Natural Screw Cap At The Top Of The Mill To Adjust The Thickness Of Peeper Or Spices) Pc 10 1,380.00 13,800.00 100 Piping Bag (transparent Disposable Plastic For Dispensing Ingredients To Pastries Length: 9 Inches Minimum Width: 3 Inches (minimum) Volume: 500 Ml (approximate) Pc 10 242.00 2,420.00 101 Plate Rack (body Shape: Rectangular Material: 304 Stainless Steel Dimension: Length-475 Mm X Width- 290 Mm X Height- 380 Mm (minimum) Pc 12 2,099.00 25,188.00 102 Preparation Table With Sink (stainless Steel, 1 Mm Thick (minimum) Dimensions: L-1200 Mm X W - 700 Mm X H - 850 Mm (minimum) Stainless Steel Tabletop And Stainless Steel Under Shelf Fully Welded Construction Sink: Left Side Single Bowl Sink With Drainer 4 Inches & Faucet Provision Sink Dimension (l X W X D) 400 Mm X 500 Mmx 25 Mm (minimum) Pc 10 4,485.00 44,850.00 103 Pressure Cooker (polished Aluminum Dimension: Diameter: 32 Cm X Height: 25 Cm (minimum) Capacity: 10 Quarts (11.3 Liters) Side Handles For Secure Carrying Equipped With Safety Opening Mechanism, Spring Safety Valve, Rubber Seal Ring) Pc 2 5,520.00 11,040.00 104 Roasting Pan (medium) Pc 10 1,840.00 18,400.00 105 Scissor, Kitchen (body Shape: Ergonomic Blade Material: Stainless Steel, 2 Mm Thick Handle Material Heavy Duty Acrylonitrile Butadiene Styrene (abs) Plastic Overall Length: 20 Cm (minimum) Width: 7.5 Cm (minimum) Pc 10 448.00 4,480.00 106 Siever, Small (stainless Steel Diameter: 20 Cm (minimum) Depth: 7 Cm (minimum) Twin Wire Handle: Length 20 Cm X 5 Mm Diameter (minimum) Fine Mesh: 0.7 Mm (1/32 Inch) (minimum) Pc 10 677.00 6,770.00 107 Skimmer, Fine (stainless Steel, Polished Overall Length: 34 Cm (minimum) Skimmer Head: Diameter -10 Cm X Depth- 4 Cm (minimum) Diameter Of Holes: 2 Mm (approx.) Handle: Length- 12 Cm X Diameter- 2 Cm (minimum) Pc 10 758.00 7,580.00 108 Skimmer, Spider (stainless Steel, Polished Overall Length: 35 Cm (minimum) Skimmer Head Diameter: 15 Cm X Depth 4 Cm(minimum) Handle Length: 12 Cm X 2 Cm Diameter (minimum) Pc 10 472.00 4,720.00 109 Soup Cup Rack (polypropylene Plastic Dimension: Length: 50 Cm X Width: 50 Cm X Height: 10 Cm (minimum) Compartment Length: 11 Cm Compartment Width: 11 Cm Compartment /inside Height: 6.7 Cm) Pc 12 1,553.00 18,636.00 110 Soup Ladle, 12 Oz Pc 10 472.00 4,720.00 111 Soup Ladle, 3 Oz Pc 10 300.00 3,000.00 112 Soup Ladle, 6 Oz Pc 10 403.00 4,030.00 113 Soup Ladle, 8 Oz Pc 10 455.00 4,550.00 114 Spatula (stainless Steel 316 Handle Material: Hardwood (smooth Finish) With Rivets Blade Dimension: Length= 7 .5 Inches X Width-1.5 Inches (minimum) Thickness Of Blade: 1.7 Mm Thick (minimum) Total Length = 12 To 14 Inches) Pc 8 294.00 2,352.00 115 Spoon, Kitchen (stainless Steel, 1.5 Mm Thick Overall Length: 30.5 Cm X Width-7.5 Cm (minimum) Spoon Head Dimension (l X W) 9 Cm X 7.5 Cm (minimum) Handle: Abs Plastic Spoon Head: Oval Type) Pc 8 403.00 3,224.00 116 Spoon, Kitchen (slotted) Oval With Slot Material: Stainless Steel, 1.5 Mm Thick Overall Length: 30.5 Cm X Width-7.5 Cm (minimum) Spoon Head Dimension (l X W) 9 Cm X 7.5 Cm (minimum) Handle: Abs Plastic Spoon Head: Oval Type With Slot At Least 6 Rectangular Slots Preferably With A Packing Case Heat Resistant Up To 220 ° C Pc 8 386.00 3,088.00 117 Spoon, Measuring (body Shape: Bowl In Shape Material: Stainless Steel, 0.7 Mm Thick (minimum) The Set Consists Of The Following Sizes: 1 Pc - 1 Tbsp. (15 Ml) 1 Pc - 1/2 Tbsp. (7.5 Ml) 1 Pc - 1 Tsp. (5 Ml) 1 Pc - 1/2 Tsp. (2.5 Ml) Set 8 291.00 2,328.00 118 Spoon, Parisienne Stainless Steel, Polished Overall Length: 240 Mm (minimum) Scoop Diameter: 30 Mm And 24mm (minimum) With Plastic Handle (polypropylene), Size: 130 Mm X Width-20 Mm (minimum) Pc 8 301.00 2,408.00 119 Spoon, Serving (stainless Steel Dimension: Length: 23 Cm X Width: 5 Cm (minimum) Scoop Dimension (l X W X D): 7 Cm X 5 Cm X 0.9 Cm (minimum) Spoon Thickness: 1.6 Mm (minimum) Pc 24 365.00 8,760.00 120 Spoon, Wooden Hardwood Dimensions: Length- 10 Inches X Width- 2 Inches (minimum) Bowl Dimension: Length -3 Inches X Width 2 Inches X Depth -3/4 Inches (minimum) Total Length: 10 Inches (minimum) Pc 8 92.00 736.00 121 Stock Pot, Large (stainless Steel, 0.8 Mm Thick (minimum) Top Diameter: 30 Cm (minimum) Height: 31 Cm (minimum) Capacity: 20 Quarts (22.7 Liters) Oven Safe To 350⁰f And Dishwasher Safe. Pc 5 2,703.00 13,515.00 122 Strainer Chinois, Small Stainless Steel Strainer Diameter: 20 Cm (minimum) Strainer Depth: 21.5 Cm (minimum) Handle Length: 20 Cm (minimum) With 2 Mm. (approx.) Fine Mesh Handle Has Provision For Hanging Preferably With A Packing Case Pc 5 380.00 1,900.00 123 Strainer Chinois, Medium (stainless Steel Strainer Diameter: 14 Cm (minimum) Strainer Depth: 13 Cm (minimum) Handle Length: 15 Cm (minimum) With 1 Mm (approx.) Fine Mesh Handle Has Provision For Hanging Pc 5 420.00 2,100.00 124 Strainer Medium, Fine Stainless Steel Strainer Diameter: 20 Cm (minimum) Strainer Depth: 7 Cm (minimum) Handle Length: 18 Cm (minimum) With 2 Mm. (approx.) Fine Mesh Strainer’s Two Layers Of Tightly Woven Mesh Catches Handle Has Provision For Hanging Pc 8 248.00 1,984.00 125 Strainer Small, Fine Stainless Steel Strainer Diameter: 13 Cm (minimum) Strainer Depth: 5 Cm (minimum) Handle Length: 13 Cm (minimum) With 1 Mm. (approx.) Fine Mesh Pc 8 240.00 1,920.00 126 Tenderizer, Medium Cast Aluminum Overall Length: 26 Cm (minimum) Dual-sided Hammer, Square Head: 6 Cm X 6 Cm (minimum) Ridged Surface With Rows Of Dull, Pyramid-shaped Spikes Weight: 250 Grams To 500 Grams Pc 8 559.00 4,472.00 127 Thermometer, Pocket /pin Tubular Pen Style Digital Thermometer Product Size: 100 Mm X 40 Mm X 14 Mm (minimum) Display Size: 40 Mm X 20 Mm (minimum) Prove Length: 200 Mm (minimum) Measuring Range: -50 °c To 300 °c (-58 ⁰f To 372 ⁰f) Resolution: 0.1 °c / 0.2 °f Pc 10 880.00 8,800.00 128 Tong, 12 Inches Stainless-steel Arms With Soft, Comfortable Grips Nylon Heads Safe For Nonstick Cookware Heat-resistant Up To 400 Degrees Fahrenheit Pc 10 322.00 3,220.00 129 Tong, 8 Inches Stainless-steel Arms With Soft, Comfortable Grips Nylon Heads Safe For Nonstick Cookware Heat-resistant Up To 400 Degrees Fahrenheit Tongs Lock Closed For Storage Preferably With A Packing Case Pc 10 291.00 2,910.00 130 Tray, Baking, Small Rectangular Material: Stainless Steel Dimension: 20 Cm X 30 Cm X 3.7 Cm (minimum) Body Thickness: 0.7- 1.0 Mm Pc 10 548.00 5,480.00 131 Tray, Utility Rectangular Material: Stainless Steel Dimension: Length- 48 Cm X Width-32 Cm X Height-2.5 Cm (minimum) Reinforced Edges Pc 12 644.00 7,728.00 132 Turner 3" X 6" Pc 10 541.00 5,410.00 133 Utility Cart Plastic, Polypropylene(pp) Dimension: (l X W X H) 84 Cm X 43 Cm X 95 Cm (minimum) Capacity: 330 Lbs (150 Kg) Loads (minimum) Three (3) Shelving With At Least 25 Cm Distance Between Shelves Tub Shelf Measure (l X W X D) 84 Cm X 43 Cm X 7 Cm (minimum) With Four (4) Swivel Caster, 10 Cm Diameter, Two Which Have Locking Brakes Pc 2 14,713.00 29,426.00 134 Weighing Scale, 1 Kg, Digital Engineering Plastic And Stainless-steel Weighing Plate Capacity: 1 Kg Accuracy: 1 Gram Back Light Lcd Display With 15 Mm Minimum High Digits Weighing Units: Gram, Ounce, Pound Size: (l X W X H Mm) 163 Mm X 245 Mm X 79 Mmm (minimum) Pc 6 1,630.00 9,780.00 135 Weighing Scale, 5 Kg Circular Bowl Material: Stainless Steel Bowl And Metal Body (coated) Mechanism Type: Spring Lever Capacity: 5 Kg /11 Lb. Sensitivity/graduated By 10 Gm Measurement Units: Gram/kilogram Manual Setting On Zero, Must Be Accurate And Durable Calibrate The Scale Using The Adjustment Knob Preferably With A Packing Case Pc 10 1,794.00 17,940.00 136 Wire Skimmer, Small Round Material: Stainless Steel, Polished Overall Length: 40 Cm (minimum) Skimmer Head Diameter: 12 Cm (minimum) Diameter Of Holes: 2 Mm (approx.) Handle Has Hole For Hanging Pc 10 408.00 4,080.00 137 Wire Whisk, Heavy Duty: Ballon Material: Heavy Duty Stainless Steel Dimensions (l X W): 31.8 Cm X 7.6 Cm (minimum) Handle Length: 12 Cm (minimum) With Hanging Loop No. Of Wires: 8 Wires Wire Diameter: 2 Mm (minimum) Pc 2 564.00 1,128.00 138 Wire Whisk, Medium Ballon Material: Stainless Steel Wire Whisk Medium Dimensions (l X W): 25.4 Cm X 7 Cm (minimum) Handle Length: 10 Cm (minimum) With Hanging Loop No. Of Wires: 6 Wires Wire Diameter: 1.8 Mm (minimum) Pc 10 488.00 4,880.00 139 Wire Whisk, Small Balloon Material: Stainless Steel Wire Whisk Medium Dimensions (l X W): 20.3 Cm X 6 Cm (minimum) Handle Length: 10 Cm (minimum) With Hanging Loop No. Of Wires: 6 Wires Wire Diameter: 1.8 Mm (minimum) Pc 10 372.00 3,720.00 140 Wok, Medium: Round Material: Carbon Steel Thickness: 1.8 Mm Thick (minimum) Dimensions (dia. X H): 45 Cm X 14 Cm (minimum) Handle Material: Steel Riveted Convenient Both Side Handle 10 Cm (minimum) With Flat Bottom Pc 10 771.00 7,710.00 141 Wok, Small Round Material: Carbon Steel Thickness: 1.5 Mm Thick (minimum) Dimensions (dia. X H): 36 Cm X 10 Cm (minimum) Handle Material: Steel Riveted Convenient Both Side Handle 8 Cm (minimum) With Flat Bottom Pc 10 679.00 6,790.00 142 Working Table Rectangular Material: 304 Stainless Steel, 1.29 Mm Thick (gauge 16) Minimum Length: 1220 Mm (minimum) Width: 700 Mm (minimum) Height: 850 Mm (minimum) Tubular Stainless Steel Legs, 38mm (minimum) With 4 Adjustable Bullet Feet Pc 5 13,628.00 68,140.00 143 Zester Standard Material: Stainless Steel Grating Surface Dimensions (l X W): 20.3 Cm X 4 Cm (minimum) Overall Length: 32.5 Cm (minimum) Handle Material: Plastic (polypropylene) Ergonomic Handle Preferably With A Packing Case Dishwasher Safe Pc 10 397.00 3,970.00 Sub Total 702,982.00 Tvl Tools & Equipment ( Food And Beverages Services) 144 Chair, Dining Side Chair Body Shape: Square Material : Metal (round Or Square) Dimension: Total Height - 33" X 15" X15" (minimum) Capacity: 150 Kg. Black Colored Powder Coated Frame With Foam On Seat Packed In Carton Box Pc 50 1,955.00 97,750.00 145 Coffee Pot, 2 Pints Round Material: Stainless Steel With Cover Capacity: 2 Pints Outside Diameter: 90 -110 Mm Over-all Height: 200 - 230 Mm Thickness: 0.5 - 1 Mm Pc 4 1,139.00 4,556.00 146 Container, Creamer Porcelain With Spout Body Shape: Circular Material: Porcelain Diameter: 50 - 65 Mm Height: 80 - 105 Mm Color: White Pc 10 288.00 2,880.00 147 Cups And Saucers 5-6 Oz. 1. Material: Porcelain 2. Capacity: 5 Oz./140 Ml 3. Heatproof Up To 300 Deg. C 4. Color: White 5. The Item Must Be Of Good Quality Packed In Carton Box Pc 24 403.00 9,672.00 148 Fork, Cocktail Material/appearance: Stainless Steel, Highly Polished, W/ Plain Design Type: Rounded Tip Handle Over-all Length: 110 - 165 Mm Width: 20 - 30 Mm (minimum) Handle Thickness: 2 Mm To 4 Mm Handle Length: 75 - 90 Mm Small, Colo: Silver The Item Must Be Branded And Have Good Quality. Pc 24 173.00 4,152.00 149 Fork, Dessert Fork Body Shape: Fork Shape, Round Tip Material/appearance: Stainless Steel, Highly Polished, With Plain Design, Rounded Tip Handle Length: 150 Mm - 175 Mm Width: 20 – 30mm Handle Thickness: 1.5mm - 3 Mm Number Of Tines: 4 Handle: 130 Mm (minimum) Color: Silver Pc 24 173.00 4,152.00 150 Fork, Dinner Fork Body Shape: Fork Shape Material / Appearance: Stainless Steel, Highly Polished, With 4tines Over - All Length: 120 - 175 Mm Thickness Of Handle: 2 - 3 Mm Color: Silver Packed In Plastic Pouch The Item Must Be Of Good Quality Pc 24 196.00 4,704.00 151 Fork, Fish Fork Body Shape: Fork Shape With Round Tip Material / Appearance: Stainless Steel, Highly Polished, With Plain Design Over-all Length: 180 - 215 Mm Fork Width: 1.5 Mm - 3 Mm Fork Thickness: 1 Mm - 2 Mm Number Of Tines: 4 Length Handle: 120 - 130 Mm Handle Thickness: 2 Mm - 3 Mm Color: Silver Packed In Plastic Pouch Pc 24 288.00 6,912.00 152 Fork, Oyster (4 To 5-1/2 Inches In Overall Length.) Pc 24 173.00 4,152.00 153 Glass, Champagne Flute Oyster Fork Body Shape: Fork Shape Material: Stainless Steel, With High Polish Appearance, And With Plain Design Length: 90 - 120 Mm Thickness: 1 Mm - 3 Mm Silver Color With Three Short Wide Curved Tines Pc 24 288.00 6,912.00 154 Glass, Collins Tumbler Body Shape: Round Material: Clear Glass Capacity: 10 Oz To 14 Oz Thickness: 1.5 -3 Mm (minimum) Packed In Carton Box Pc 24 173.00 4,152.00 155 Glass, Juice / Hi- Ball Material: Clear Glass Type: Hi-ball Height: 140 - 160 Mm Bottom Diameter: 50 -70 Mm Top Diameter: 50 - 70 Mm Thickness: 2 - 4 (minimum) Capacity: 8 Oz. To 10 Oz. Dishwasher Safe The Item Must Be Branded And Good Quality Pc 24 518.00 12,432.00 156 Glass, Pilsner (iced Tea Glass) Type: Flared Rim Body Shape: Round Slender Material: Clear Glass Capacity: 20 Oz. To 23 Oz. Over-all Length: 22 -25 Cm Thickness Of Glass: 1 -3 Mm With Flared Rim And Slender Shape Packed In Carton Box The Item Must Have Good Quality Pc 24 288.00 6,912.00 157 Glass, Red Wine Balloon Shaped Bowl Material: Crystal Clear Glass Rim Diameter: 55 - 60 Mm Thickness: 1.5 Mm - 3 Mm Over - All Length : 200 -220 Mm Capacity: 250 -300 Ml Stem Diameter: 6 - 8 Mm Stem Length: 85 - 90 Mm Base Diameter: 75 - 85 Mm Base Thickness: 2 - 4 Mm Pc 24 403.00 9,672.00 158 Glass, White Wine Balloon Shaped Bowl Material: Crystal Clear Glass Rim Diameter: 55 - 60 Mm Thickness: 1.5 - 3 Mm Over -all Length: 200 -220 Mm Capacity: 270 - 300 Ml Stem Diameter: 6 - 8 Mm Stem Length: 75 - 85 Mm Base Diameter: 70 - 80 Mm Base Thickness: 2 - 5 Mm Pc 24 443.00 10,632.00 159 Gravy Boats Boat Shape With Handle Material: Stainless Steel Capacity: 5 Oz. Appearance: Mirror Polish Finish Size :17cm X 7.3cm X 8.2 Cm / 6.7 X 2.9 X 3.2 Inches (minimum) The Item Must Have Good Quality Pc 4 225.00 900.00 160 Ice Bucket, 2 Liters With Tongs Circular Set Includes: Ice Bucket Material: Stainless Steel Diameter: 140 - 180 Mm Height: 140 - 170 Mm Thickness Of Bucket : 0.7 - 2 Mm Capacity: 2 Liters (minimum) Pc 5 471.00 2,355.00 161 Knife, Butter Stainless Steel W/ Highly Polished Appearance Over-all Length: 140 Mm - 150 Mm Handle Thickness: 3 Mm - 5 Mm With Dull Edge And Rounded Tip Pc 24 127.00 3,048.00 162 Knife, Dinner Flat With Round Tip Material / Appearance: Stainless Steel Blade Highly Polished Handle Material: Stainless Steel Overall Length: 160 - 190 Mm Blade Thickness: 2 - 4 Mm Handle Thickness: 3 - 6 Mm Pc 24 213.00 5,112.00 163 Knife, Fish Flat With Pointed Tip Material / Appearance: Stainless Steel, Highly Polished W/ Plain Design Overall Length: 200 - 220 Mm Width Blade: 20 - 25 Mm Thickness Of Blade: 2 Mm - 4 Mm Thickness Of Handle: 3 Mm - 6 Mm Pc 24 207.00 4,968.00 164 Menu Folder (a4 (297mm X 210 Mm) And A5 (210 Mm X 148 Mm) Pc 5 518.00 2,590.00 165 Napkin Holder Rectangular Material: Stainless Steel With Highly Polished Appearance Dimension: Width: 70 - 90 Mm X Length : 150 - 170 Mm Thickness: 0.7 Mm -2 Mm Packed In Plastic Pouch Pc 6 247.00 1,482.00 166 Order Pads Rectangular Material: 80gsm Offset Paper Each Pad Comes With A 100 Sheets And Corresponding Copy Page Each Pad Has Sequentially Numbered Orders To Make It Easy To Keep Track With 100 Sheets Per Pad And 10 Pads Included Pc 5 58.00 290.00 167 Pepper And Salt Mill: Round Body Material: Wood Size: Diameter: 5 Cm X Height: 20 Cm (minimum) Carved Of Wood With Stainless Steel Grinding Mechanism Color: Natural Pc 20 1,380.00 27,600.00 168 Plate Covers Circular Material: Stainless Steel, Mirror Polished Diameter: 10 1/4 Inches (minimum) Height: 2 7/8 Inches (minimum) Thickness: 1/16 Inch. (minimum) With Handle Pc 8 305.00 2,440.00 169 Plate, Dessert, 7”to 8” Circular Material: Porcelain Supply Must Be A Set, Consisting Of One (1) Of Each: 7 Inches And 8 Inches Plates Color: White Inner Diameter: 145 To 165 Mm Thickness: 3 To 6 Mm Pc 24 207.00 4,968.00 170 Plate, Dinner, 10” Circular Material: Porcelain With No Design Color: White Inner Diameter: 200 Mm - 215 Mm Outer Diameter: 250 - 260 Mm Thickness: 3 Mm - 6 Mm Pc 24 437.00 10,488.00 171 Plate, Fish, 8” To 9” Circular Material: Porcelain With No Design Supply Shall Be A Set Consisting Of: One (1) Each 8 Inches And One (1) Each, 9 Inches Color: White Inner Diameter: 165 Mm - 190 Mm(minimum) Thickness: 3 Mm - 6 Mm Pc 24 207.00 4,968.00 172 Round Table (8's) (54” Or 60”) Pc 10 9,034.00 90,340.00 173 Salad Forks (6” Long) Pc 24 127.00 3,048.00 174 Salad Knife 8” Pc 24 207.00 4,968.00 175 Salad Plates 7” To 8” Pc 24 242.00 5,808.00 176 Salt And Pepper Shakers Square Material: Glass And Aluminum Over-all Height: 75 -90 Mm Length: 50 -60 Mm Width: 50 -60 Mm Pc 4 207.00 828.00 177 Sauce Ladles Circular With Pouring Spout Material: Stainless Steel, Highly Polished Appearance Over-all Length: 220 -230 Mm Ladle Bowl Length: 60 -65 Mm Long Ladle Bowl Diameter: 65 -70 Mm Depth: 10 -15 Mm Handle Details: 150-155 Mm Long X 20 -30 Mm Wide X 2 - 4 Mm Thick Pc 10 403.00 4,030.00 178 Server, Cake Stainless Steel Blade, Highly Polished Appearance 2. Over-all Length: 220 To 270 Mm 3. Width: 60 - 80 Mm 4. Thickness: 1.5 Mm To 2 Mm 5. Handle: 120 -140 Mm Long, Non-toxic Plastic 6. Shape: Shovel-shaped 7. Color: Silver Pc 10 571.00 5,710.00 179 Service Forks : Fork Shape Material/appearance: Stainless Steel, Highly Polished, W/ Palin Design Over-all Length: 220 Mm - 260 Mm Width: 20 - 25mm Handle Thickness: 1.5 Mm - 4 Mm Handle Length - 165 Mm - 185 Mm 4 Tines Color: Silver Pc 6 207.00 1,242.00 180 Service Tray: Rectangular Material: Plastic (pp) Size: 14 Inches X 18 Inches X 1 Inch (minimum) Colo: Any Pc 6 518.00 3,108.00 181 Show/service/ Base Plates 11” To 14” Round Material: Porcelain With No Design Supply Must Be A Set Consisting (1) Of Each: - 11 Inches, - 12 Inches, - 13 Inches, And - 14 Inches Plates Color: White Diameter, Inner : 225 Mm - 250 Mm Thickness: 3 Mm - 6 Mm Set 6 1,208.00 7,248.00 182 Side Plates Or Bread Plates 6” Round Material: Porcelain With No Design Color: White Inner Diameter: 95 Mm To 120 Mm Outer Diameter: 145 Mm To 170 Mm Thickness: 3 Mm - 6mm Pc 24 242.00 5,808.00 183 Side Towels Rectangular Material: Oxford Polyester Soft Cloth Over-all Length: 640 - 680 Mm Over-all Width: 420 -460 Mm Color: Plain White Pc 10 349.00 3,490.00 184 Silver Platter Round Material: Stainless Steel Diameter: 300 -330 Mm Thickness: 1 - 2 Mm Pc 10 570.00 5,700.00 185 Soup Bowl Circular Material: Porcelain Capacity: 24 Oz. (minimum) Pc 24 437.00 10,488.00 186 Soup Ladle Circular Material: Stainless Steel, Highly Polished Appearance Over-all Length: 220 -235 Mm Ladle Bowl Details: 60 -65 Mm Long, 60 -75 Mm Diameter, 10 -15 Mm Deep Pc 10 366.00 3,660.00 187 Soup Tureen Round Material: Stainless Steel Capacity: 7 - 11 Quart Size: 60 X 35 X 32 Cm (minimum) Pc 10 695.00 6,950.00 188 Spoon, Dessert Oval Material/appearance: Stainless Steel, Highly Polished With Plain Design Over-all Length: 175 To 190 Mm Thickness: 2 Mm - 3 Mm Shorter Handle: 120 -130 Mm Color: Silver Pc 24 125.00 3,000.00 189 Spoons, Service Oval Material: Stainless Steel, Highly Polished, W/ Plain Design Over-all Length: 220 Mm - 250 Mm Width: 30 - 38 Mm Handle Thickness: 1.5 Mm - 4 Mm Handle Length - 165 Mm - 185 Mm Color: Silver Pc 6 136.00 816.00 190 Spoons, Soup (cream And Consume) Round Material/appearance: Stainless Steel, Highly Polished, W/ Plain Design, Rounded Tip Handle Over-all Length: 165 Mm - 200 Mm Smaller Oval Shaped Spoon Bowl And Tapers Slightly To The Tip Pc 24 160.00 3,840.00 191 Steak Knife (5”) Pc 24 251.00 6,024.00 192 Sugar Container Round Material: Glass With Brass Lid (or Equivalent) Diameter: 70 -80 Mm Height: 130 -140 Mm Capacity: 12 Oz. Pc 10 288.00 2,880.00 193 Tablecloth, 54 X 54 Inches Rectangle Material: Linen Color: Any Color But Not Black Feature: Washable Pc 10 942.00 9,420.00 194 Tablecloth, 64x64 Inches Rectangular Rectangle Material: Linen Color: Any Color But Not Black Feature: Washable Pc 10 1,208.00 12,080.00 195 Table Napkins, Cloth, 16” X 16” Plain Cloth Body Shape: Square Material: Oxford Polyester Cloth Or Its Equivalent Color: Plain White Pc 60 424.00 25,440.00 196 Table Skirting Cloth Square Material: American Cotton Twill Cloth Color: Any Color Except Black Dimension: 90 Inches X 90 Inches (minimum) Packed In Plastic Pouch Pc 10 2,185.00 21,850.00 197 Table, Square/rectangular (4's Or 6's) Square/rectangle Materia: High Density Polyethylene Tabletop Powder Coated Steel Frame Dimension: 37 - 39 X 37 - 39 Inches Color: White Pc 4 5,382.00 21,528.00 198 Tea Pot, 2 Pints Porcelain Type Body Shape: Round With Handle And Pouring Spout Material: Porcelain Capacity: (2 Pint) Color: White Pc 10 1,139.00 11,390.00 199 Teaspoon Tea Spoon Body Shape: Oval Tip Material/appearance: Stainless Steel, Highly Polished, W/ Plain Design Over-all Length: 120 Mm To 140 Mm Handle Thickness: 2 Mm To 4 Mm Short Handle Length - 100 Mm (minimum) Color: Silver Pc 24 92.00 2,208.00 200 Tong, 8 Inches Standard Material: Stainless Steel Stainless-steel Arms With Soft, Comfortable Grips Nylon Heads Safe For Nonstick Cookware Heat-resistant Up To 400 Degrees Fahrenheit Pc 7 291.00 2,037.00 201 Tooth Pick Holder Round Material: Stainless Steel, Highly Polished In Appearance Diameter: 30 -35 Mm Diameter (minimum) Height: 65 -75 Mm Capacity: 1.24 Oz. (minimum) Packed In Plastic Pouch Pc 10 101.00 1,010.00 202 Tray Stand Rectangular Material: Chrome Plated Metal Folding Tray Stand Length: 470 -490 Mm Width: 400 -440 Mm Height: 770 -790 Mm Pc 5 2,282.00 11,410.00 203 Tray, Bill Folders/ Change Height: 190 - 220 Mm 3. Width: 120 -140 Mm 4. Thickness: 2 Mm To 3 Mm (minimum) 5. Color: Black Pc 5 271.00 1,355.00 204 Tray, Round (bar) Round Material: (pe/abs) Plastic Rubberized Surface, Non-slip/grip Tight Over-all Diameter: 345 -360 Mm (minimum) Thickness: 2 - 4 Mm (minimum) Color: Black Pc 8 443.00 3,544.00 205 Water Goblet Balloon-shaped Bowl Material: Crystal Clear Glass Over-all Length: 200 -220 Mm Capacity: 270 Ml To 300 Ml Rim Diameter - 55 -65 Mm Thickness: 1 Mm To 3 Mm Stem Length : 75 -85 Mm Stem Diameter : 6 -8 Mm Base Thickness : 3 -4 Mm Base Diameter : 7 -80 Mm Pc 24 124.00 2,976.00 206 Water Pitcher Stainless Steel, Highly Polished Appearance Height: 170 Mm To 220 Mm Top Diameter: 110 -120 Mm (approximate) Capacity: 1 - 1.5 Liter With Pour Spout Pc 10 516.00 5,160.00 Sub Total 571,245.00 Total Amount 2,336,280.00 2. The Department Of Education, Schools Division Of Ilocos Sur Now Invites Bids For The Above Procurement Project. Delivery Of The Goods Is Required Within Thirty (30) Calendar Days. Bidders Must Have Completed, Within 10 Years From The Date Of Submission And Receipt Of Bids, A Contract Similar To The Project Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii (instructions To Bidders). 3. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using Non-discretionary “pass/fail” Criteria As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) No. 9184. Bidding Is Restricted To Filipino Citizens/sole Proprietorships, Or Organizations With At Least Sixty Percent (60%) Interest Or Outstanding Capital Stock Belonging To Citizens Or Organizations Of A Country The Laws Or Regulations Of Which Grant Similar Rights Or Privileges To Filipino Citizens, Pursuant To Ra No. 5183. 4. Prospective Bidders May Obtain Further Information From Deped, Schools Division Of Ilocos Sur, And Inspect The Bidding Documents At The Address Given Below From 8:00 A.m. Until 5:00 P.m. 5. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders On February 28-march 18, 2025 (until 9:00 A.m.) From The Given Address And Website/s Below And Upon Payment Of The Applicable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb Amounting To Five Thousand Pesos (p5,000.00). The Procuring Entity Shall Allow The Bidder To Present Its Proof Of Payment For The Fees In Person, By Facsimile, Or Through Electronic Means. 6. The Deped, Schools Division Of Ilocos Sur Will Hold A Pre-bid Conference On March 7, 2025, At 10:00 A.m. At The Schools Division Office, Bantay, Ilocos Sur, And/or Through Videoconferencing/webcasting Via Google Meet Using The Link: Https://meet.google.com/tjb-zntu-yys Which Shall Be Open To Prospective Bidders. 7. Bids Must Be Duly Received By The Bac Secretariat Through Manual Submission At The Office Address As Indicated Below, On Or Before March 19, 2025, 9:00 A.m. Late Bids Shall Not Be Accepted. 8. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 16. 9. Bid Opening Shall Be On March 19, 2025, At 9:01 A.m. At The Given Address Below And/or Through And/or Virtual. Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend The Activity. 10. The Deped, Schools Division Of Ilocos Sur Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Before Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Implementing Rules And Regulations (irr) Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 11. For Further Information, Please Refer To: Marillac D. Quinsaat Head – Bac Secretariat Department Of Education, Schools Division Of Ilocos Sur Zone V, Bantay, Ilocos Sur, 2727 Email Address: Ilocos.sur@deped.gov.ph 12. You May Visit The Website/s: For Downloading Of Bidding Documents: Depedilocossur.info Date Of Issue: February 28, 2025 Joye D. Madalipay, Ceso Vi Chairperson, Bids And Awards Committee

Details: Description 1. The Department Of Education – Division Of Tangub City, Through The General Appropriations Act 2024 Intends To Apply The Sum Of Three Million Nine Hundred Seventy-eight Thousand One Hundred Six Pesos (php 3,978,106.00) Being The Approved Budget For The Contract (abc) To Payments Under The Contract For Second Procurement Of Learning Tools And Equipment For Technical Vocational Livelihood To Deped-public Schools With Identification Number Tvl - 2025 – Rx – Tangub City – 030.a. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. Quantity Unit Item Description Abc Lot 1. Lorenzo Tan National High School (caregiving Nc Ii)- Php 400,403.00 5 Piece Airpot 1.type: Water Heater 2. Outer Material: Hard Plastic, (pp) Polypropylene, Heat Resistant 3.cavity Material: Stainless Steel 4. Capacity: 2.5 Liters 5.voltage: 220/240/volts 6.ac 50/60 Hz. Power In Watts: 500 To 800 Watts 7.comes With English Manual That Contains: Users Guide, List Of Parts, Maintenance Guide, Safety Guide 8. The Item Must Be Branded And Good Quality. 10 Piece Apron 1.type: Bib Apron 2. Material: Polyester-cotton Fabric 3.length: 20 To 40 Inches (minimum) 4. With 2 To 3 Bottom Pockets; 5.color: Any 6.the Item Must Be Of Good Quality 2 Piece Bath Tub, Baby 1. Material: Hard/sturdy Plastic, (pp) Polypropylene 2. Color: Any 3.dimension: (l X W X H) 670 To 700 Mm X 400 To 420 Mm X 160 To 190 Mm (minimum) 4. Thickness: 3 Mm To 6 Mm (minimum) 5.color: The Item Must Be Of Good Quality 10 Piece Baby Blanket 1. Type: Blanket 2. Material: 100% Cotton 3.color: White 4. Dimension: (l Xw) 38 To 42 Inches X 28 To 32 Inches (minimum) 5. Washable 6. The Item Must Be Of Good Quality 20 Piece Basin (small) 1.material: Hard Plastic, (pp) Polypropylene 2. Color: Any 3.dimension: 280 - 320 Mm Diameter X 80 - 120 Mm Higher (mimimum) 4. Thickness: 2 Mm To 4 Mm (minimum) 5. The Item Must Be Of Good Quality 20 Piece Bath-towel, Towellete 1. Type: Bath Towel 2. Material: 100% Cotton 3.color: White 4. Dimension: ( L X W ) 120 - 125 Cm X 60 - 65 Cm (minimum) 5.washable 6.the Item Must Be Of Good Quality 5 Piece Bedpan 1.material: Hard Plastic, (ps) Polystyrene 2. Color: Any Color 3.dimension: ( L X W X H) 22 - 26 Cm X 27 - 32 Cm X 7 - 12 Cm (minimum) Approximate 4. Capacity: 1 Liter (minimum) 5.thickness: 2 To 5 Mm 6.saddle-shaped And Lightweight 7. The Item Must Be Of Good Quality 10 Piece Blanket 1. Type: Blanket 2. Material: Cotton 3.color: White 4. Dimension: (l X W) 80 - 90 Inches X 54 -64 Inches Approximate 5. Washable 6. The Item Must Be Of Good Quality 3 Piece Bottle Sterilizer, Electric 1. Type: Electric Steam Sterilizer 2. Material: Hard Plastic (p E) Polyethylene Or Its Equavalent 3.color: Any Color 4. Capacity: 6 Bottles (minimum) 5.sterilizes Bottle And Accessories By Steam 6. With Automatic Power Shut-off Function 7. Dimensions: 8. Power Supply: 220 V-240v Ac, 50/60 Hz. 9. The Item Must Be Of Good Quality 5 Piece Bread Toaster 1. Type: Electric Bread Toaster 2. Dimensions ( W X D X H): 25 - 30 Cm X 15 -20 Cm X 18 - 22 Cm (minimum) Approximate 3. Capacity: 2 Slices 4. Power Supply: 220v-240v Ac, 50/60 Hz. 5. 400 To 600 W (minimum) 6. The Item Must Be Of Good Quality 10 Piece Burping Cloth 1. Type: Burping Cloth 2. Material: 100% Cotton 3. Color: Any Color 4. Dimension: Length: 17 -19 Cm Width: 14 -16 Cm (minimum) 5.washable 6. The Item Must Be Of Good Quality 10 Piece Cane 1.type: Adjustable Offset-walking Cane 2. Material: Aluminum 3.tip Size: 18 4. Height Adjustment: 31 Inches To 39 Inches (with 1 Inch. Increment) 5.weight Capacity: 200 - 250 Lbs. (minimum) 6.with Rubber Handle; With Push-botton Height Adjustment 7. The Item Must Be Of Good Quality 5 Piece Carpet 4ft. X 8 Ft 1.material: Polyster 2. Color: Any Patterned Color 3.dimension:48 Inches X 96 Inches (minimum) 4.the Item Must Be Of Good Quality 5 Set China Ware 1.material: Porcelain 2. Fit To Be Used In Ovens And Microwaves 3.specific Dimensions: Dinner Plate Diameter: 10 Inches (minimum) 4. Salad Plate Diameter: 7 Inches (minimum) 5.bowl Diameter: 5 Inches (minimum) 6.mug: 12 Oz. (minimum) 7. The Item Must Be Of Good Quality 8. Set Includes: 1 Piece Dinner Plate, 1 Set Salad Plate, 1 Piece Bowl, 1 Piece Mug 10 Piece Clothes Brush 1. Type: Rectangular Clothes Brush 2. Handle Material: Wood 3. Bristle Material: Plastic Bristle 4. Color: Any Color 5.overall Dimension: ( L X W X H) 140 -160 Mm X 45- 60 Mm X 20 -30 Mm (minimum) 6. The Item Must Be Of Good Quality 10 Piece Clothes Hamper 1. Type: Square Hamper 2. Material: Polyester 3. Color: Any Color 5. Dimension: ( L X W X H) 32 To 34 Cm X 36 To 38 Cm X 56 To 58 Cm (minimum) 5. The Item Must Be Of Good Quality 2 Piece Clothes Rack 1.type: Single-pole Clothes Rack 2. Material: Stainless Steel 3. Dimension: ( L X W X H) 30 To 32 Inches X 14 To 38 Inches X 62 To 64 Inches (minimum) 4. Comes With 4 Caster Wheels 5. The Item Must Be Of Good Quality 3 Piece Comforter 1.type:comforter 2. Material: Polyester 3.color: Any Color 4. Dimension: ( L X W) 84 To 88 Inches X 62 To 65 Inches (minimum) 5.thickness: 20-30 Mm (minimum) 6.washable 7. The Item Must Be Of Good Quality 3 Piece Commode 1.type: Foldable Commode 2. Durable Plastic Snap- On Seat And Lid Withouot Pushing Buttons 3. Blue Powder-coated Steel-welded Construction 4. Plastic Arms For Added Comfort 5.comes Complete With 12 Qt. Commode Bucket With Carry Handle, Cover And Splash Shield 6. Specifications: Width 18 Inches Between Arms/ 22.5 Inches Outside Approximate 7. Set Dimensions: W 32 -36 Cm X D 35 -40 Cm, Height 38 -54 Cm Approximate 8. Weight 13 Lbs., Weitgh Limit 350 Lbs. 9. The Item Must Be Of Good Quality 5 Set Cooking Utensils 1. Material: Stainless Steel 2. The Set Is Comprised Of Ff:; 1 Pc. -16 X 9.5 Cm Sauce Pan With Glass Lid (minimum) 3. 1 Pc. - 16 X 95 Cm Casserole With One Glass Lid, (minimum) 4. 1 Pc. - 18 X 10.5 Cm Casserole With Glass Lid, (minimum) 5.1 Pc. - 20 X 11. 5 Cm Casserole With Glass Lid, (minimum) 6. The Item Must Be Of Good Quality 2 Piece Crutches, Adjustable 1.type: Adjustable Crutches 2. Set Includes: 3 Pcs./set 3.material: Aluminum Powder-coated 4. Color: Any Color 5.weight Capacity: 300 Lbs. (minimum) 6. Dimensions: Youth Size 7. User Heights: 4 Ft. 6 Inches To 5 Ft. 2 Inches 8. Underarm Height: 37 Inches To 46 Inches 9. Adult Size: User Heights: 5 Ft. 2 Inches To Ft. 10 Inches 10. Underam Heights: 45 Inches To 53 Inches 11. Tall Adult Size: User Heights: 5 To 10 Inches 12. Underam Height: 53 Inches To 61 Inches 13. The Item Must Be Of Good Quality 10 Piece Cutlery 1.material: Stainless Steel 2. 20 Pieces Set For 4 3. 4 Dinner Knives 4. 4 Dinner Forks 5. 4 Dinner Spoons 6. 4 Salad Forks 7. 4 Tea Spoons 8. The Item Must Be Of Good Quality 10 Piece Cutting Board, Plastic 1. Material: Polyethylene Plastic 2. Color: Any Color 3. Dimension: ( L X W X H) 240 - 260 Mm X 140 - 160 Mm X 10 - 15 Mm (minimum) 4. Reversible Cutting Surface 5. The Item Must Be Of Good Quality 10 Piece Digital Thermometer, 32 C-42.9 C (90.0f-109.9f 1. Case Material: Hard Plastic (pe) Polyethylene 2. Color: Any Color 3. Range: 32 C - 42.9 C (90.0f-109.9f) 4. Accuracy: + 0.1c 35.5c-42.0c(+ 0.2 F 95.9f-107.6f) 5. Battery Operated 6.memory: Last Measuring Reading 7.alarm: Approx. 10 Seconds Sound Signal When Peak Temperature Reached. 8. The Item Must Be Of Good Quality 2 Piece Dressing Trolley 1.material: Shelves: Powder-coated Steel Sheet 2. Dimensions: ( W X D X H) 48 - 50 Cm X 48 - 50 Cm X 83 - 85 Cm (minimum) 3.number Of Shelves: 2 4. With Four Revolving Castors, Two Lockable 5. The Item Must Be Of Good Quality 10 Piece Electric Knife 1. Type: Electric Knife 2. Material: Stainless Steel And Hard Plastic, (pe) Polyethylene 3. Power Supply: 220/240 Volts, Ac 50/60 Hz. 4. Dimensions: 4.25 X 2.75 X 11.88 Inches (minimum) 5.comes With Touch Button Control, Safety Lock And English User & 39;s Manual 6. Comes With English Manual That Contains: Users Guide, List Of Parts, Maintenance Guide, 7. The Item Must Be Of Good Quality 10 Piece Face Towel/towellete 1. Type: Face Towel 2. Material: 100% Cotton 3. Color: White 4. Dimension: ( L X W ) 28- 32 Cm X 28 -32 Cm (minimum) 5. Washable 6. The Item Must Be Of Good Quality 10 Piece Feeding Bottle Brush 1. Bristle Material: Nylon 2. Color: Any Color 3. Handle Material: Hard Plastic, (ps) Polystyrene 4. Total Length: 280 -320 Mm (minimum) 5. Fit With The Standard Feeding Bottle For The Baby 6.comes With Nipple Brush 7. Washable 8. The Item Must Be Of Good Quality 5 Set Feeding Utensils (child) 1.material: Hard Plastic, (ps) Polystyrene 2. Sets Includes: 6 Pcs./set 3. 1 Pc Knife 4. 1 Pc- Plate 5. 1 Pc. -bowl 6. 1 Pc. - Cup 7. 1 Pc. -fork 8.1 Pc. - Spoon 9. Color: Any 10. The Item Must Be Of Good Quality 7 Set First Aid Kit Type: Emergency Case; Contents: First Aid Quick Reference Guide, 1 Pc; Sterize Gauge Swab (4x 4 X 12 Ply) 100 Pcs/pack, 1 Pack; Adhesive Strips/band-aid, 50 Pcs/pack, 2 Packs; Gloves, Disposable, Medium Size, 2 Pairs; Hypo Allergenic Adhesive Tape, 5 Cm X 5 Cm, 2 Rolls; Triangular Bandage/arm Sling, Min 90 Cm X 90 Cm X 120 Cm, 2 Pcs; Safety Pins, 1 1/4 Inches, (12 Pcs), 1 3/4 Inches (12 Pcs); Stainless Steel Bandage Scissors, 2 Pcs; Betadine, 60ml, 2 -3 Years Expiration, 2 Bottles; Dust Mask, 2 Pcs; Hand Towels Or Face Towels, White Color, 6 Pcs; Gauze Bandage, Minimum 5 Cm X 4cm, 2 Rolls; Antiseptic Handwash/germicidal Soap, 60 Gms, 2 Pcs; Torniquet, 2 Pcs; Spirit Of Ammonia, 30ml, 2-3 Years Expiration, 1 Bottle; Burn Cream Ointment, 20g To 30g, 2-3 Years Expiration, 1 Tube; Medical Tweezers Min. 8 Cm, Plastic, 2 Pcs; Plastic Bags, Resealable, Minimum Of 24 Pcs, 100mm X 180mm, 24 Pcs, 150mm X 230mm; Cotton Balls, 50 Balls In A Sealed Package, 2 Packs; Hot And Cold Pack, Reusable, 1 Pack; Water Resistant And Sturdy Case W/ Handle That Can Accomodate All The Listed Items. 20 Piece Flat Sheet 1.type:bed Sheet 2. Material: 100% Cotton 3. Color: White 4. Dimension: Width - 137 - 145 Cm Length - 180 -200 Cm (minimum) 5. Washable 6. The Item Must Be Of Good Quality 10 Piece Garbage Bin Type: Swivel Lid Garbage Bin Body Shape: Round Material: Hard Plastic, Polypropylene Dimension: 4 Gallons ( Minimum) Removable Dome Shape Lid With Spring Return Swivel Preferably With Packing Case Color: Any Color Smooth And No Rough Surfaces 20 Box Gloves, Rubber (15 Mils) Medium Size (#8) Super Nitrile, Flocklined Interior (acid/solvent Resistant) Individually Packed For Hand Protection 10 Box Gloves, Surgical (disposable) 1.material: Latex 2. Color: White 3. Thickness: .09 Mm (minimum) 4. Disposable And Sterile 5. The Item Must Be Of Good Quality 20 Piece Gown (hospital) 1.type:unisex Hospital Gown 2. Material: Polyester- Cotton 3. Color: Any Color 4. Size: One Size Fits All 5. Comes With Overlap Back Closure 6. The Item Must Be Of Good Quality 5 Set Grooming Kit (hairbrush Comb, Nail Cutter, Nail Brush) 1. Set Includes: 6 Pcs./ Set (minimum) 2. Materials: Stainless Steel And Hard Plastic 3. 2 Nail Clippers/ Trimmers Of Different Sizes 4.1 Multipurpose Scissors 5. 1 Ear Pick 6. 1 Tweezer 7. 1 Comb 8. The Item Must Be Of Good Quality 10 Piece Hand Towel 1. Type: Hand Towel 2. Material: 100% Cotton 3. Color: Any Color 4. Dimension: ( L X W) 65 -75 Cm X 32 -42 Cm (minimum) 5. Washable 6. The Item Must Be Of Good Quality 3 Piece High Chair/booster Seat/ Portable Seat 1. Material: Foldable Powder Coated Steel Frame Or Its Equavalent 2. Phone Type: Corded 3. Polyester Harness, Seat/back Cushion 4. Overall Dimensions: ( L X W) 65 -75 Cm X 50 -60 Cm X 90 - 102 Cm (minimum) 5. Capacity: 40 Lbs. (minimum) 6. With 3-position Seat Recline 7. The Item Must Be Of Good Quality 10 Piece Hot Water Bag 1. Material: Rubber Or Its Equavalent 2. Color: Any Color 3. Overall Dimension: (lxw) 200- 300 Mm X 150 -200 Mm (minimum) 4. Leak-proof And Washable 5. The Item Must Be Of Good Quality 10 Piece Kettle 1. Material: Heat-resistant Hard Plastic 2. Capacity: 1- 1.5 Liters (minimum) 3. Height: 25-35 Cm (minimum) Approx 4. Voltage: 220/240 Volts, Ac 50/60 Hz 5. Power In Watts: 1000 To 1500 Watts 6.comes With Automatic Shut-off Feature And Permanent Water Level Indicator 7. Pitcher-type With Pouring. 8. Comes With English Manual That Contains: Users Guide, List Of Parts, Maintenance Guide, 9. The Item Must Be Of Good Quality 10 Set Measuring Cups .. 1/4, 13, 1/2 1 Cup Set 1. Materials: Stainless Steel 2. Set Includes: 4 Pcs./set; 3. 1 Pc. - 1/4 Cup (60 Ml) 4. 1 Pc- -1/3 Cup (80ml) 5. 1 Pc.- 1/2 Cup (125 Ml) 6. 1 Pc. - 1 Cup ( 250 Ml) 7. Thickness: .5 Mm To 1 Mm (minimum) 8. The Item Must Be Of Good Quality 10 Piece Medical Tray 1. Type: Tray 2. Material: Stainless Steel 3. Overall Dimension: (lxw X D) 300- 350 Mm X 200 -250 Mm X 12 - 19 Mm (minimum) 4. Thickness: .7 To 1 Mm (minimum) 5. The Item Must Be Of Good Quality 2 Set Mixing Bowl, Stainless, 6-piece Set 1. Material: Stainless Steel 2. Quantity Of Set: 6 Pcs./set 3. Dimension: 3/4 Qt., 1.5 Qt., 3 Qt., 4 Qt., 5 Qt., 8 Qt., 4. The Item Must Be Of Good Quality 10 Piece Pail, Plastic, 10 Liters 1. Material: Polyethylene Plastic 2. Dimension: 25-30 Cm Diameter X 23-27 Cm Depth (minimum) 3. Color: Any Color 4. Chromed Finished Handle 5. Capacity: 10 Liters (minimum) 6. Material Must Be Non-toxic 7. The Item Must Be Of Good Quality 10 Piece Pans 1. Type: Frying Pan 2. Material: Stainless Steel 3. Handle: With Hard Plastic Heat Insulation 4. Tempered Glass Lid With Steam Hole 5. Size 23 -26 Cm With Lid 6. The Item Must Be Of Good Quality 10 Piece Peeler 1. Type: Peeler 2. Blade Material: Stainless Steel 3. Handle Material: Stainless Steel 4. Overall Dimensions: 18 X 8 Cm (minimum) 5. Comes With Self-locking 6. The Item Must Be Of Good Quality 10 Piece Pick Up Forcep 1. Type: Curved Forceps 2. Material: Stainless Steel 3. Overall Length: 100-130 Mm (minimum) 4. Comes With Self-locking 5. The Item Must Be Of Good Quality 10 Piece Pillow 1. Material: Cotton 2. Color: Any Color 3. Dimensions: ( L X W) 50 - 56 Cm X 75 - 180 Cm (minimum) 4. With 4 Inches Hems 5. Washable 6. The Item Must Be Of Good Quality 20 Piece Pillow Case 1. Material: Cotton 2. Color: Any Color 3. Dimensions: ( L X W) 50 - 56 Cm X 75 - 180 Cm (minimum) 4. With 4 Inches Hems 5. Washable 6. The Item Must Be Of Good Quality 10 Piece Portable Mixer 1. Type: Portable Mixer 2. Material: Stainless Steel, Clear Acrylic 3. Capacity: 16-18 Oz. (minimum) 4. Size: 170 - 220 Mm X 75- 100 Mm 5. Requires 2 Aaa Batteries 6. Power In Watts: 250 To 300 Watts 7. The Item Must Be Of Good Quality 10 Piece Potato Masher 1. Type: Portable Masher 2. Material: Stainless Steel And Hard Plastic 3. Mesh Head Diameter: 70-90 Mm (minimum) 4. Overall Length: 250 - 270 Mm (minimum) 5. Handle Length: 120-140 Mm (minimum) 6. Washable 7. The Item Must Be Of Good Quality 5 Set Pots 1. Type: Cooking Pot 2. Material: Stainless Steel 3. Set Includes: 4 Pcs./set 4. 1 X Pot With Lid 5. 1 X Pan With Lid 6. 1 X Strainer 7. 1 X Egg Streamer 8. Size: (l X W X H) 40 To 42 Cm X 12 To 14 Cm X 26 To 28 Cm 9. The Item Must Be Of Good Quality 5 Piece Skillet 1. The Item Shall Have The Following Specifications. Material Including Handle: Cast Iron 2. Color: Any Color 3. Dimension ( Dia. X Depth): 250 - 320 Mm X 50 - 70 Mm (minimum) 4. Handle Casted With The Body And Having Plastic Or Rubber Heat Insulator 5. Body Thickness: 1.5 - 3 Mm (minimum) 6. Washable 7. The Item Must Be Branded And Have Good Quality. 5 Piece Sphygmomanometer 1. Type: Aneroid 2. Material: Nylon Cuff And Inflation Bag, Die - Cast Zinc Manometer 3. Package Inlcluded: 1 X Aneroid Sphygmomanometer. 4. Size: ( L X W X H Cm) = 18 To 20 Cm X 11 To 13 Cm X 11 13 Cm 5. Nylon Zippered Carrying Case 6. Capacity: 0 To 300 Mm Hg 7. The Item Must Have Good Quality. 5 Piece Stethoscope 1. Type: Dual Head Stethoscope 2. Material: Stainless Steel Chestpiece And Eartubes 3. Reinforced Pvc Tubing 4. Soft Pvc Eartips 5. Color: Any Color 6. Bell Diameter: 18-25 Mm Approx. 7. Diaphragm Diameter: 25-50 Mm Approx. 8. Overall Length: 66-75 Cm (minimum) 9. The Item Must Be Of Good Quality 5 Piece Urinal 1. Type: Unisex Portable Urinal 2. Material: Hard Plastic, (pp) Polypropylene 3. Color: Any Color 4. Total Capacity: 28 Oz. Minimum 5. Dimension: ( L X W X H) 270 To 290 Mm X 145 To 160 Mm X 70 To 80 Mm ( Minimum) 6. Thickness: 1 Mm To 3 Mm (minimum) 7. The Item Must Have Good Quality. 5 Piece Vacuum Cleaner 1. Material: Plastic (pp) Polypropylene Or Its Equavalent 2. Color: Any Color 3. Suction Power: 18 To 22 Kpa (minimum) 4. Tank Capacity: 24 Liters (minimum) 5. Vacuum Hose Length: 6 To 8 Ft. (minimum) 6. Power Supply: 220 V - 240 Ac , 50/60 Hz. 7. With Accesories: Extension Wand, Utility Nozzle, Standard Paper Filter 8. Comes With English Manual That Contains: Users Guide, List Of Parts, Maintenance Guide, Safety Guide 9. The Item Must Be Branded And Good Quality 3 Piece Wheel Chair 1. Type: Foldable Wheel Chair 2. Overall Dimensions: ( L X W X H) 40 - 44 Inches X 26 - 30 Inches X 34 - 38 Inches ( Minimum) 3. Folded Dimensions: ( L X W X H ) 40 To 44 Inches X 10 To 14 Inches X 34 To 38 Inches (minimum) 4. Capacity: 350 Lbs. (minimum) 5. With Padded Arm Rests; With Push-to-lock Wheel Brakes 6. The Item Must Be Of Good Quality Lot 2. Sta. Maria National High School (hairdressing Nc Ii)- Php 323,170.00 5 Pcs. Bowl, Mixing, Plastic With 10.5 Cm X 6cm 2 Pcs. Bowl, Shampoo, Stainless Steel Frame, Bowl Dimensions: 19 Inch X 20 Inch X 10 Inch With Hose Attachment Of 7 Ft. 5 Box Box, Hairpin, Metal With 3.5 X 4.5 X 0.5 Inches(100 Pcs Per Box) 5 Pcs. Brush, Applicator, Plastic With 70mm X 80mm 5 Pcs. Brush, Hair, Plastic Bristle And Wooden Handle, Width - 2 Inches 10 Pcs. Cap, Frosting, With Hook, Silicone With 31cm X 22cm,rounded Metal Hook 10 Pcs. Cap, Heating, Waterproof, Cordless With 21-24 Inches 10 Pcs. Cape, Polyester With 125 Cm X 140 Cm 5 Pcs. Chair,high, Metal Painted With Anti Rust With 15 Inches X 33 Inches, Synthetic Leather Seat 5 Pcs. Chair, Hydraulic, Metal Base With 59 Cm X 54 Cm X 51-78cm, 180kg, 360' Rotation 10 Pcs. Clamp, Plastic, Length:9.5cm, Thickness:10mm 10 Pcs. Clamp, Duck Bill, Metal, Length: 11 Cm, Elasticity Stainless Steel Spring 5 Pcs. Clipper, Hair, Body Material: Hard Plastic, Blade Material: Carbon Steel, 6 Watts 10 Pcs. Comb, Afro, Plastic, Length: 7 Inches, Width: 3.25 Inches, Number Of Teeth: 12 Teeth, Teeth Height: 2.5 Inches 10 Pcs. Comb, All Purpose, Plastic, 18 Cm Long , Has Both Fine And Medium Teeth Position On One Side Only, Height Of The Teeth: 2 Cm 10 Pcs. Comb, Haircutting, Hard Plastic, Length Including The Handle:180mm, Width: 30mm With Detachable Steel Blades And Blade Holder 10 Pcs. Comb, Large Toothed, Plastic, Size:15 Cm, Number Of Teeth: 10 Teeth, Gap Between Comb's Teeth: 0.4 To 0.5 Cm , Teeth Size: 0.3 Cm X 4cm 10 Pcs. Comb, Tail, Plastic, Size : 8 Inches X 1 Inches, Tail Length: 4 Inches Tooth Length: 3/4 Inch 10 Pcs. Comb, Teasing, Plastic,1st Row: Large Teeth 25 Mm Long, 2nd Row: Small Teeth 19 Mm, Over-all Size: 20cm X 3.8 Cm 5 Pcs. Comb, Wide Tooth, Plastic, Size:15 Cm, Number Of Teeth:10 Teeth, Gap Between Comb's Teeth:0.4 To 0.5 Cm, Teeth Size: 0.3cm X 4cm 8 Pcs. Crimpers, 25 Watts, Size:38 Cm X 15.5 Cm X 9 Cm, Maximum Temp.: 200 Degrees Centigrade, Rated Voltage:10 -230volts Ac 5 Pcs. Curling Iron, Ceramic, 65watts, 210-240volts Ac, Barrel Size: 1 Inch, Adjustable Heat Setting Of 200 Degrees Centigrade, Swivel Cord Up To 360 Degree 5 Pcs. Drip Pan, Hard Plastic, Size:17.5 X 25.8 X 1 Inches, Thickness: 1/8 Inch, Shallow Rectangular Type 5 Pcs. Dryer, Hair, 1000w, Rated Voltage: 220vac, 18.5cm X 16cm X 6.5cm With Plastic Handle Design 10 Box Gloves, Disposable, Size: 25cm X 23cm, 100 Pcs Per Box 5 Pouch Gloves, Rubber, Medium, Thickness: 4 Mil, Acid Resistant 5 Pouch Gown, Smock, Polyester, Sizes: Small (50inches X 56inches);medium (52inches X 58inches); Large (54 Inches X 60inches) 10 Pouch Hairclips, Metal, Size:67mm X 19mm 10 Pack Hairnet, Invisible, Nylon, Size: 55mm, Stretchable, Color: Black 10 Pc Headband, 6 Inches, Woven Crochet Tube 10 Pc Headband, Flannel, Cloth, Size : 45 Cm, Width: 8 Cm 6 Pc Infrared Iron, Ionic Ceramic Tourmaline-infused Plates And Abs Plastic Body, Power: 70 Watts, Power Rating: 220-240 Volts Ac; Over-all Size: 24 Cm, Heating Plate 50 Mm, Heating Time: Within 30 Seconds;variable Heat Settings: From 250 To 450 Degrees Fahrenheit 10 Pc Mirror, Hand, Plastic, Size 15 Cm Diameter, Frame Thickness: 6.5mm, Over-all Length With The Handle: 20 Cm 3 Pc Mirror, Modular, Plain Mirror, Mirror Material: Glass, Frame Material: Aluminum (cut To Fit), Dimensions: 75 Cm X 65 Cm, Mirror Thickness: 6mm 10 Pc Prong Clip, Double, Steel, Size: 45 Mm 10 Pc Prong Clip, Single,steel, Size: 55 Mm 10 Pc Razor, Straight, High Carbon Steel, Foldable Straight Razor, Replaceable Blade; Dimensions: 14 Cm X 2 Cm When Folded; Double-edged Razor Blades 3 Dz Roller Pins, Metal, Size: 60mm Long, Quantity By Dozen(12 Pieces) 10 Pc Rollers, Jumbo, Plastic 44mm In Diameter X 64mm 10 Pc Rollers, Large Sized, Plastic, Size: 40mm Diameter X 60mm Long 10 Pc Rollers, Medium Sized, Plastic; Diameter: 38 Mm ,length: 58mm 4 Pc Scissor, Cutting, Stainless Steel,length: 17cm,blade Width 10 Cm 4 Pc Scissor, Thinning, High Carbon Steel, Blade Length 6cm, Style: Right Handed Scissor, Length: 17cm 5 Pc Scoop, Plastic, Capacity:1/2 Cup, Rounded Edges With Handle Thickness: 1.5 Mm 5 Pc Shower Cap, Plastic, Size: One Size Fits All Or 30cm 5 Pc Spatula, Plastic, Dimension: 7.5 Cm X 1.5 Cm 5 Pc Spray Gun, Transparent Plastic, Capacity: 300ml, Dimension: Bottom Is 7 Cm And The Height Is 17cm 3 Pc Steamer, Hair, 450 Watts, 220 Volts/50-60hz, Hood Material: Polycarbonate, Hood 30 Cm Diameter Opening X 25 Cm, Timer Setting Is Up To 60 Minutes, 32 Ounce Water Reservoir, Adjustable Height 100- 150cm 30 Pcs. Stool, Metal, Electroplated, Load Capacity: 150kg, Design: Swivel Stool With Backrest With Hydraulic Lift To Adjust Height Freely Lot 3. Sta. Maria National High School (wellness Massage Nc Ii)-php 198,338.00 5 Pcs. Dummy, Anatomical, Plastic, 32" Tall, 27 Removable Parts That Are Held On By Metal Screws, Posts, And Hooks, Brain (2parts), Lungs (2 Parts), Heart (2 Parts, Liver, Intestines, Stomach, Base Is 13" X 9" (removable), Weighs 12 Lbs. 5 Pcs. Massage Bed/table, Hard Wood With Steel Bracings, Hardwood Frame, Marine, Plywood Deck; Color: Black, Dimensions: W:75 Cm X L:183 Cm X H: (adjustable) Height: Adjustable From 24 In. - 33in., Leg Thickness - 35mm, Cushion System: High Density Foam (7.5 Cm / 2.95") With Pu Leather Cover (1mm Thick), Weight Capacity: 250 Kg(minimum), Gross Weight: 21 Kg 2 Pcs. Massage Chair, Padded With 3" Thick, High-density, Small-cell Foam, Size: 14"-diameter Seat But Without Back And Arm Rest, With Metal Post And Hard Plastic Star, Pneumatic Spring Will Effortlessly Adjust The Height From 18" To 24" With The Pull Of A Lever, Five Heavy-duty, Smooth-rolling Wheels, Load Capacity: 265 Lbs / 120 Kg (maximum), Smooth Surface And No Sharp Edges 6 Pcs. Sphygmomanometer, 33 To 42 Cm Arm Diameters, Accuracy: ±3mm Hg;measurement Range : 0mm Hg To 300mm Hg; Smallest Scale: 1mm Hg Index And Range Markings On The Dial For Clear Readings, Nylon Cuff Is Durable And Stain Resistant With A Velcro Closure 6 Pcs. Stethoscope, Stainless Steel Double Chest Piece, Color: Black, Tubing Description: Y-tube Pvc, Uses Extra Soft Replaceable And Pivotable Ear Tips, The Binaural Is Chromium-plated, Chest-piece Diameter: 44 Mm And Non-chill Rim, Overall Length: 29" /74 Cm 6 Pcs. Talking Sphygmomanometer, Nylon Cuff Sizes: 33 To 42 Cm Arm Dia, Dimensions: 98mm*126mm*60mm, Measurement Range : 0mm Hg To 300mm Hg; Smallest Scale: 1mm Hg, Weight: 450g , Range: 20~280mmhg(0.4kpa-37.3kpa), Pressure Accuracy: ±3mmhg(±0.4kpa), Pulse Measurement Range: 40 ~199 Beats /min, Voltage: 4*aaa Alkaline Batteries 25 Pcs. Talking Thermometer, Hard Plastic, Sensing Unit: Thermistor, Measurement Range: 32 C - 42 C (89.6f-107.6f), Measurement Accuracy: ± 0.1c 32c-42.0c (± 0.2 F 89.6.9f-107.6f), Power Supply: 1.5v Dc, Lr41 Alkaline-magnesium Button Battery Real Voice, Temperature Display: 3-digit, +deg C (deg F) Display In 0.1 Degree Increment, Dimension Approx.: 2.0 (w) X 4.4 (h) X 1.2 (d) Inches / 51 (w) X 110 (h) X 30 (d) Mms 26 Pcs. Thermometer, Digital, Hard Plastic, Sensing Unit: Thermistor, Measurement Range: 32 C - 42 C (89.6f-107.6f), Measurement Accuracy: ± 0.1c 32c-42.0c (± 0.2 F 89.6.9f-107.6f) Power Supply: 1.5v Dc, 1 Lr41 Alkaline-magnesium Button Battery , Power Consumption: 0.1mw, Temperature Display: 3-digit, +deg C (deg F) Display In 0.1 Degree Increment, External Size (mm): 19.4(w) × 132.5 (l) × 10.0(d) 10 Pcs. White Board, White Formica Laminated, Board Size: Rectangular 1800mm W X 1000 To 1200mm H, Board Edges Secured With Aluminum Clip Edging 17 Mm Wih Plastic Corner Caps, The Stand And Frame Are Constructed With Aluminum Or Powder Coated Steel 25mm Square Tube , Sturdy, No Wobble With 4 Lockable Hard Plastic Caster Wheels, Height From Floor: 210 To 214cm Lot 4. Sumirap National High School And Tangub City National High School (bpp Nc Ii)-php 519,702.00 10 Set Air Compressor With Airbrush Cake Decorating Set(airbrush Gravity Feed Dual Action Airbrush Compressor Kit 0.2/0.3/0.5mm Needle Air Brush For Cake Decorating Painting. Material: Aluminum + Copper Type: Single Cylinder Piston Compressor Power: 1/5 Hp Plug Type: Eu Voltage: 220-240v/50hz Speed: 1450 Rpm Air Volume Per Minute/liter: 23l/min Maximum Pressure: 7bar (100psi) Working Pressure Of Spray Gun: 15-50psi Low Noise: ≤50db Accessories: Pressure Gauge, Pressure Gauge, Air Filter Automatic Stop, Starts At 2.8 Bar, Stops At 4 Bar (special Pressures Available) Connection: With Connection G 1/8" Bsp Cable: Approx. 1.8m / 6ft) 40 Pc Egg Beater(stainless Steel Semi-automatic Mixer/manual Whisk Egg Beater Kitchen Cooking Tool) 40 Set Board, Chopping ,6 Color( Type: Food Grade Body Shape: Rectangular Material: Plastic (polypropylene), Food Grade Board Size: Length: 38 Cm (minimum) Width: 30 Cm (minimum) Thickness: 1.27 Cm (minimum) Color-coded For Use With Different Types Of Food, Blue, Red, Yellow, Green, Brown And White, Preferably Packed In Set Comes With No Sharp Edges And With Hole For Storage Purposes) 10 Pc Double Boiler (material: Stainless Steel Thickness: 1/16 Inch (1.5 Mm) (minimum) Lid Material: Glass Rivetedhandle On Both Side Diameter: 9 1/2 Inches (minimum) Total Height: 9.4 Inches (minimum) Inset Bottom Diameter: 9 Inches (minimum) Inset Top Diameter: 9 Inches (minimum) Capacity: 2 Liters (minimum) Must Be A Set Which Includes One (1) Saucepan, One (1) Boiler, And One (1) Lid With Stainless Steel Handle And Smooth Surfaces With No Sharp Edges) 80 Set Bowl, Mixing Set Stainless (premium Stainless Steel Mixing Bowls Bowl Sizes Are: 5 Qt, 4 Qt, 3qt, 1.5qt, And ¾ Qt And They Each Fit Perfectly Within One Another) 70 Set Cake Pan, Round, Size: 4''x3'' (non-stick Aluminum Alloy Cake Round Pan) 30 Set Cake Stand, With Tier (type: Cake Stand With Tier, Food Grade Body Shape: Circular With 3 Tier Material: Hard Plastic, Polypropylene, 4 Mm Thick The Tier Consists Of The Following Sizes: Tier 1: 18 Cm Diameter (minimum) Tier 2: 25 Cm Diameter (minimum) Tier 3 : 30 Cm Diameter (minimum) Column Diameter: 20 To 30 Mm (solid) Distance Between Tiers: 15 Cm Over-all Length: 30 Cm (minimum) Assembled Column Is Used For Maximum Strength And Stability Of The Stand Must Be Packed In Set ) 60 Pc Cake Turn Table (type: Turn Table Body Shape : Circular Material: Cast Aluminum Plate.and Cast Iron Base Upper Plate: 30 Cm Diameter (minimum) And 1.4 Cm Thickness (minimum) Base Dimensions: 18 Cm (minimum); 1.4 Cm Thickness (minimum) Total Height: 10 Cm To 15 Cm Turntable With Ball Bearing To Turn Easier Preferably Packed In Any Kind Of Packaging Comes With No Sharp Edges To Rotate Smoothly In 360 Degrees Clockwise Or Counter Clockwise ) 30 Pc Coupler (type: Foood Grade Body Shape: Tubular Material: Hard Plastic, Polypropylene, Any Bright Color Height: 3cm (minimum) Top Diameter: 1.27 Cm (minimum) Bottom Diameter: 2.54 Cm (minimum) Preferably With Storage Case The Materials Used Must Be Non-toxic And Dishwasher Safe ) 50 Set Cup, Measuring (stainless Steel Measuring Cup Set For Dry Ingredients. Composed Of 1 Cup, 3/4 Cup, 1/2 Cup, 1/4 Cup, 1/8 Cup) 50 Set Cup, Measuring 250 Ml. For Liquid Glass (250 Ml Heat Resisting Measuring Glass) 40 Set Cup, Measuring 500 Ml. For Liquid Glass (500ml Heat Resisting Measuring Glass) 40 Pc Cutter, Dough (type: Scrapper Body Shape: Straight Blade Material: Stainless Steel Straight Blade With Stainless Steel Handle Blade Dimension: Lenght : 15 Cm X Width: 11 Cm X Thickness: 1.2 Mm(minimum) Handle Dimension: Length: 15 Cm X Diameter: 3 Cm (minimum) Preferably With Packing Case Food Grade And Dishwasher Safe Design Allows Item To Be Hung For Storage) 40 Pc Cutter, Pie (stainless Steel Rolling Knife/pizza Cutter) 30 Pc Flour Sifter,hand Cranked (type: Hand Cranked Body Shape: Round Shape Material: Stainless Steel Dimension: Diameter: 133.3 Mm ( Minimum) X Height: 165 Mm (minimum) Thickness: 0.79 Mm (minimum) (body) And Constructed With Stainless Steel Wire Mesh # 30 Bottom Volume Markings Should Be Seen Inside And Outside Of The Sifter Capacity: 5 Cups (1.18 Liter) Spring Action Squeeze Handle Stainless Steel Preferably With A Packing Case Dishwasher Safe) 40 Pc Grater (type: Four Sided Box Grater Body Shape: Box In Shape Material: Stainless Steel Blade And Plastic (polypropylene Handle) Grater Dimensions: Height- 25 Cm X Width-13 Cm X Depth-10 Cm (minimum) Side 1: Large-hole Shredder With 6 Mm Hole Side 2: Slicer Side 3: Small-hole Shredder With 3 Mm Hole Side 4: Grater With Strips About 1.27 Cm To 2.54 Cm Length Preferably With Packing Case Food Grade & Dishwashing Safe) 50 Pc Knife, Kitchen (premium Quality Stainless Steel Kitchen Knife, 6-8” In Length) 20 Pc Knife, Pallete (premium Quality Stainless Steel Pallete Knife Ideal For Butter.) 50 Pc Ladle, 3oz (premium Quality Stainless Steel Soup Ladle, 3oz) 40 Pc Loaf Pan, Big (carbon Steel Non-stick Loaf Pan, Size: L=32,w=13,h=7cm Minimum) 40 Pc Loaf Pan, Medium (carbon Steel Non-stick Loaf Pan, Size: L=28, W=15.5, H=7cm Minimum) 40 Pc Loaf Pan, Small (carbon Steel Non-stick Loaf Pan, Size: L=25.5, W=13.5, H=6cm Minimum) 40 Pc Muffin Pan, Big (carbon Steel Non-stick Muffin Pan, 12 Holes,3oz) 40 Pc Muffin Pan, Medium (carbon Steel Non-stick Muffin Pan, 9 Holes,3oz) 40 Pc Muffin Pan, Small (carbon Steel Non-stick Cupcake Pan, 6 Holes) 70 Pc Pie Pan, 10'' (premium Stainless Steel/aluminum Pie Plate. Thick And Durable, 10” In Diameter) 70 Pc Pie Pan, # 8 (premium Stainless Steel/aluminum Pie Plate. Thick And Durable, 8” In Diameter) 50 Set Pillars, Cake (premium Quality Acrylic Cake Support Pillar, 12cm In Diameter(minimum),straw Size Diameter ) 60 Pack Piping Bag (reusable Silicone Piping Bag, Biggest Size, 100pcs Per Pack) 40 Pc Rectangular Pan (carbon Steel Non-stick Rectangular Cake Pan. Size: L=10.8", W=7", H=1.5", Minimum) 70 Pc Rolling Pin, Plastic (non-stick Rolling Pin Made With Food Grade Nylon, Size:13") 100 Pc Rubber Scraper, Silicone (size: 21cm X 4.1cm, Material: Silicone) 40 Pc Sauce Pan Non Stick (non-stick Sauce Pan With Lid, Size: 20cm) 40 Pc Sheet Pan / Cookie Sheet (aluminum Baking Sheet, Size: 13x18”) 50 Set Spoon, Measuring (premium Quality Stainless Steel Measuring Spoon Set, Compost Of 1/8tsp, 1/4tsp, 1/2tsp, 1tsp, 1/4tbsp, 1/2tbsp, 1tbsp)) 70 Pc Spoon,wooden (premium Quality And Durable Long Handled Wooden Spoon/ladle. Length: 30.5cm Minimum) 40 Pc Strainer (stainless Steel, Fine Mesh Strainer, Size: 18cm) 40 Set Tip, Decorating, Large (type: Tube Tips Body Shape: Nozzles With Different Shape Material: Stainless Steel Tube Height: 3.5 Cm To 5 Cm Tube Diameter: 2 Cm To 3.5 Cm Thickness: 0.5 Mm (minimum) Tube Tip: Assorted Designs (create Swirls, Rosettes, Flowers, Roping,stars, Leaves And Other Designs Comes With 24 Different Shapes Of Nozzles Packed In Plastic Storage Box Smooth And Deformities Free Must Be Branded) 30 Pc Weighing Scale, 10 Kg. (kitchen Weighing Scale, 10kg Maximum) 40 Pc Weighing Scale, 5 Kg. Digital(digital Kitchen Weighing Scale, Digital Price Computing Weight Electronic Scale, Capacity Is At Least 5kilograms, Pan Size 34.5 X 23.5cm) 70 Pc Wire Whisk, Medium (stainless Steel Wire Whisk, Size: 14”) Lot 5. Sumirap National High School And Tangub City National High School ( Cookery Nc Ii )-php 1,405,964.00 30 Pcs. Apple Corer, Body Shape: Tubular Material: Stainless Steel Total Length: 18 Cm (minimum) Handle Material: Hard Plastic, Polypropylene Handle Dimension: Length-10 Cm X Diameter-2 Cm (minimum) Blade Size: Length-8cm X Diameter-2 Cm (minimum) Preferably With Packing Case Dishwasher Safe. 4 Pcs. Bain Marie, Table, (food Warmer) Body Shape: Rectangular Material: 304 Stainless Steel, 0.8 Mm Thick (minimum) Dimensions: Length-1500 Mm X Width-700mm X Height-800 Mm (minimum) Power Soiuce: Voltage: 220 Volts - 230 Volts, 50 Hz/ 60 Hz With Royal Cord 1.5 Meter Long With Attachment Standard Type A Male Plug Or Provide Plug Adopter 10a/220v 20 Pcs. Blender, Electric Heavy Duty, Body Shape: Round Jar Material Housing: Plastic (polypropylene) Jar Height : 25 Cm To 28 Cm Jar Thickness: 4 Mm To 8 Mm Heat Resistant Glass Jar With Cover Source Voltage: 220 Volts / 240 Volts,50 Hz / 60 Hz With Power Cord 1.5 Meter Long With Attachment Of Standard Type A Male Plug Or Provide Plug Adopter 10a/220v. Power Wattage: 300 To 700 Watts Blade: Stainless Steel, 3 To 4 Metal Blades 40 Pc Board, Chopping/ Cutting, Plastic, Body Shape: Rectangular Material: Plastic (polypropylene), Food Grade Board Size: Length: 15 Inches (minimum) Width: 12 Inches (minimum) Thickness: 0.5 Inch (minimum) With Hole For Storage Purposes Preferably With Packing Case Food Grade And Dishwasher Safe. 20 Pcs. Boiler, Double, Material: Stainless Steel Thickness: 1/16 Inch (1.5 Mm) (minimum) Lid Material: Glass Riveted Handle On Both Side Diameter: 9 1/2 Inches (minimum) Total Height: 9.4 Inches (minimum) Inset Bottom Diameter: 9 Inches (minimum) Inset Top Diameter: 9 Inches (minimum) Capacity: 2 Liters (minimum) 30 Pcs. Braising Pan, Medium, Body Shape: Round Material: Enameled Cast Iron And Stainless Steel Size: Diameter: 28 Cm X Height: 10 Cm (minimum) Capacity: 4 Liters (approximate) With Stainless Steel Cover, Solid Cast Stainless Steel Side Handles And Riveted Handle On Both Side: Length: 10 Cm (minimum) Handle Diameter: 8 Mm To 10 Mm 30 Pcs. Can Opener, Body Shape: Materials: Stainless Steel Dimension: Length-21 Cm X Width 10 Cm X Depth:2.5cm (minimum) Multi-use: 3 In 1 Can Opener Also Opens Bottle Tops- Can Lids And Tabs. 30 Pcs. Casserole,medium Pot, Body Shape:round Material:stainless Steel, 0.7 Mm Thick Dimension: Diameter- 24 Cm X Height -14 Cm (minimum) Tempered Glass Lid Welded Handle On Both Sides, Size: 7.5 Cm (minimum) Handle Diameter: 8 Mm To 10 Mm Preferably With Packing Case . 30 Pcs. Casserole,small Pot, Body Shape: Round Material: Stainless Steel, 0.7 Mm Thick Dimension: Diameter- 20 Cm X Height -12 Cm (minimum) Tempered Glass Lid Welded Handle On Both Sides, Size: 7.5 Cm (minimum) Handle Diameter: 8 Mm To 10 Mm. 20 Pcs. Colander, Medium, Medium Body Type: Round Material: 304 Stainless Steel Diameter: 30 Cm (minimum) Capacity: 8 Quarts (9 Liters) Welded Handle On Both Sides, Size: 7.5 Cm (minimum) Handle Diameter: 8 To 10 Mm Body Thickness: 0.8 Mm (minimum) 20 Pcs. Colander, Small, Body Shape: Round Material: 304 Stainless Steel Diameter: 26 Cm (minimum) Capacity: 5 Quarts (5.6 Liters) Welded Handle On Both Sides, Size: 7.5 Cm (minimum) Handle Diameter: 8 Mm To 10 Mm Body Thickness: 0.8 Mm (minimum) Full-ring Support Base, 15 Cm Diameter Preferably With Packing Case Food Grade And Dishwasher Safe 20 Set Cup,measuring( For Solid) Set Body Shape: Round Material: Stainless Steel, 0.7 Mm Thick (minimum) Each Set Contains The Following: 1 Pc - 1 Cup (237 Ml) 1 Pc - 1/2 Cup (118 Ml) 1 Pc - 1/3 Cup (79 Ml) 1 Pc - 1/4 Cup (59 Ml) Handle Dimension: Length-12 Cm X Width-1 Cm (minimum) Measuring Capacity Engraved On The Handle Strip Handles Have Provision For Hanging Preferably With Packing Case Smooth Surfaces And Dishwasher Safe 20 Pcs. Dispenser,paper Towel Body Shape: Rectangular Material: Abs Plastic Dimensions: Length =260 Mm X Width =100 Mm X Height = 211 Mm (minimum) Capacity: 200 Paper Paper Size: Length-20 Cm X Width- 8 Cm (approximate) Mounting Style: Wall Mounted Tissue Box 12 Pcs. Fan, Electric, Ceiling Material: Metal, Plastic Size/diameter: 18 Inches Power Rating: 70 Watts (minimum), 220 / 240 Vac, 50 / 60 Hz, Single Phase Rotation Angle: 90 Degrees Base: Stable, 16 Inches Diameter (approx.) Removable Metal Guard On Front And Rear 3-speed Settings Comes With 1.5 Meters Power Cord And With Molded Male Plug To Adapt Type A Outlet (or Providing 3a Minimum Plug Adapter Is An Option) Smooth Surface, No Sharp Edges Includes User's Manual In English Which Contains: A. A Diagram Of The Parts With Their Names 6 Pcs. Fire Extinguisher With Contents .for Type A, B, C Fire: Dry Chemicals (monoammonium Phosphate) 2.portable Type 3.capacity : 5 - 6 Kgs 4.rechargeable Cylinder Metal 5.working Pressure Of Cylinder : 400 Psi 6.brass Valve With Pressure Gage 7.with Rubberized Hose And Aluminum Nozzle Attached 8.with Squeeze Lever To Discharge And Safety Pin 10.painted With Metal Primer And Red Enamel Paint 20 Pcs. Fish Poacher,medium, Body Shape: Oval Pot For Poaching Material: Stainless Steel, 0.64 Mm Thick Dimensions (l X W X D): 45 Cm X 15 Cm X 12 Cm (minimum) Handle Material: Stainless Steel Riveted Looped Handles On Both Side, 7 Cm (minimum) Handle Diameter: 8 Mm To 10 Mm Includes Stainless Steel Lid With Handle And Removable Insert 20 Pcs. Fork, Carving Body Shape: Square Shape Prong Prong Material:high Carbon Stainless Steel Overall Length: 30 Cm (minimum) Blade Dimension: Length- 15 Cm X Width- 0.5 Cm X Thickness- 0.3 Cm (minimum) Number Of Prongs: 2 Prong Comes With Square- Shaped Prongs And Pointed Tips Abs Plastictriple-riveted Handle Preferably With Packing Case 400 Pcs. Fork, Kitchen Body Shape: Standard Material: Stainless Steel Dimension: Length - 32 Cm X Width- 3.5 Cm (minimum) Fork Size: Length: 8 Cm X Width -3.5 Cm (minimum) Handle :abs Plastic Number Of Tines: 2 Tines With Tapered End 36 Dozen Frying Pan, Large, Non Stick, Body Shape: Round Pan Material: Aluminum With Non-stick Coating Thickness: 3 Mm Thick (minimum) Dimension: Diameter-30 Cm (minimum) X Height- 5.5 Cm (minimum) 40 Pcs. Frying Pan, Medium, Non Stick, Body Shape: Round Pan Material: Aluminum With Non-stick Coating Thickness: 3 Mm Thick (minimum) Dimension: Diameter-24 Cm (minimum) X Height- 4.5 Cm (minimum) Handle Material: Stainless Steel With Silicone Riveted Handle: 19 Cm Long (minimum) Preferably With A Packing Case 30 Pcs. Frying Pan Small, Non Stick , Body Shape: Round Pan Material: Aluminum With Non-stick Coating Thickness: 3 Mm Thick (minimum) Dimension: Diameter-20 Cm (minimum) X Height- 3.8 Cm (minimum) Handle Material: Stainless Steel With Silicone Riveted Handle: 12 Cm Long (minimum) Preferably With A Packing Case Oven Safe Up To 250⁰f 22 Pcs. Funnel, S/s, Medium, Body Shape: Round Material: 304 Stainless Steel Dimension: Diameter-15 Cm (minimum) X Height- 15.8 Cm (minimum) Tube Diameter: 2 Cm X Length: 7.3 Cm (minimum) Comes With Handle For Easy Hanging Preferably With Packing Case Dishwasher Safe 22 Pcs. Funnel, S/s, Small, Body Shape: Round Material: 304 Stainless Steel Dimension: Diameter-11 Cm (minimum) X Height- 10 Cm (minimum) Tube Diameter: 1.5 Cm X Length: 5 Cm (minimum) Comes With Handle For Easy Hanging Preferably With A Packing Case Dishwasher Safe. 20 Pc Garbage Bin, Body Shape: Round Material: 304 Stainless Steel Dimension: Diameter-11 Cm (minimum) X Height- 10 Cm (minimum) Tube Diameter: 1.5 Cm X Length: 5 Cm (minimum) Comes With Handle For Easy Hanging Preferably With A Packing Case Dishwasher Safe. 20 Pc Glass Rack, Body Shape: Square Material: Polypropylene Plastic Overall Dimensions: Length - 19 1/2 Inches X Width - 19 1/2 Inches X Height - 4 Inches (minimum) Compartments: Full-size 25 Individual Compartment Glass Rack Compartment Dimensions: Length - 3 1/2 Inches X Width - 3 1/2 Inches X Height - 4 Inches (minimum) Easy Grip Handles Molded Into All Four Sides Preferably With A Packing Case 20 Pc Ice Cream Scoop, Stainless Steel Ice Cream Scoop 45mm. Simply Squeeze Handle. 30 Pc Knife,boning, Body Shape: Ergonomic Material: High Carbon Steel Overall Length: 28 Cm (minimum) Blade: Length-15 Cm X Width- 3 Cm (minimum), Pointed Tip Cutting Edge Angle From Tip To The Heel Is 13 To 14 Degrees Handle Length: 12 Cm (minimum) Handle Material: Hard Plastic Handle With Rivets Preferably Wiht Packing Case Dishwasher Safe 30 Pc Knife,chef, Body Shape: Flat Materials: Stainless Steel Overall Length: 30 Cm (minimum) Blade Size: Length - 20 Cm X Width-4 Cm (minimum) Blade Thickness: 2.5 Mm (minimum) 30 Pc Knife,cleaver, Cutting Edge: Straight, Pointed End Type: Cleaver Knife Body Shape: Flat Blade Material: Forged Stainless Steel Heavy Duty Blade Length: 17 Cm (minimum) Overall Length: 30 Cm (minimum Cutting Edge: Straight Handle Material: Ergonomic Wood Handle With Triple Rivets Blade Thickness: 3 Mm (minimum) 30 Pc Knife,oyster, Body Shape: Ergonomic Blade Material: Stainless Steel Blade Dimension: Length - 7 Cm (minimum) X Width - 2 Cm (minimum) Blade Thickness: 2 Mm (minimum) Handle Material: Smooth Wooded Handle Rounded Handle Size: Length-10 Cm X Diameter- 3.5 Cm (minimum) Total Length (from The Tip Of The Handle Up To Tip Of The Blade) :17 Cm (minimum) 4 Pc Light,emergency, 2 Heads Led Materials: Metal, Anti-rust Coated Duration Time (2 Heads): 5 Hours (minimum) Automatically Light Up During Power Outage Overcharge And Over- Discharge Protection Built - In Ac Charger, Power Cord Plug To Adapt Type A Outlet (or Providing 5a Minimum Plug Adapter Is An Option) Battery Test Switch - External Safety Fuse Head: White Led 1w (minimum) 3.5 " Dome Reflector 4 Pc Meat Slicer, Body Shape: Circular Housing Material: Die Cast Aluminum Alloy And Body Painted Dimensions: Width-40.5 Cm X Depth- 45.7 Cm X Height- 38 Cm (minimum) Stainless Steel Rotary Blade Diameter: 190 Mm (minimum) Power Source: 220 Volts-230 Volts, 60 Hz With Power Cord 1.5 Meter Long With Attachment Of Standard Type A Male Plug Or Provide Plug Adopter 10a/220v 30 Set Pastry Tube, Stainless Steel Pastry Tube 24, Big 40 Pc Peeler, Y -type, Rack Dimension: Length: 38 Cm X Width 23 Cm (minimum) Type: Y-type Peelers Body Shape: Ergonomic Material: Stainless Steel Overall Dimensions (l X W X H): 7 Inches X 2 1/4 Inches X 1 Inch (minimum) Blade Material: 304 Stainless Steel, 0.7 Mm Head Dimension: (l X W X H) 2 1/4 Inches X 2 1/4 Inches X 1 Inch (minimum) Handle Material: Stainless Steel Handle Length: 4 3/4 Inches X 1 Inch Diameter (minimum) 2 In 1 Design With 2 Blade Reel, Built In Potato Eye Remover And Hole For Hanger Preferably With A Packing Case 14 Set Pepper And Salt Mill Food Grade And Non-toxic Material. Mill Cookery Nc Ii Type: Pepper & Salt Mill Body Shape: Round Body Material: Wood Size: Diameter: 5 Cm X Height: 20 Cm (minimum) Carved Of Wood With Stainless Steel Grinding Mechanism 20 Pack Piping Bag, Body Shape: Triangular Material: Transparent Disposable Plastic For Dispensing Ingredients To Pastries Length: 9 Inches Minimum Width: 3 Inches (minimum) Volume: 500 Ml (approximate) 10 Pc Plate Rack Shape: Rectangular Material: 304 Stainless Steel Dimension: Length-475 Mm X Width- 290 Mm X Height- 380 Mm (minimum) 12 Set Preparation Table With Sink, Heavy Duty Wire Shelving, 2.6 Mm Diameter (minimum) Table With Sink Cookery Nc Ii Type: Preparation Table With Sink & Sheleves Body Shape: Rectangular Material: Stainless Steel, 1 Mm Thick (minimum) Dimensions: L-1200 Mm X W - 700 Mm X H - 850 Mm (minimum) Stainless Steel Table Top And Stainless Steel Under Shelf Fully Welded Construction Sink: Left Side Single Bowl Sink With Drainer 4 Inches & Faucet Provision Sink Dimension (l X W X D) 400 Mm X 500 Mmx 25 Mm (minimum) 4 Pc Pressure Cooker, Cooker Body Shape: Round Material: Polished Aluminum Dimension: Diameter: 32 Cm X Height: 25 Cm (minimum) Capacity: 10 Quarts (11.3 Liters) Side Handles For Secure Carrying Equipped With Safety Opening Mechanism, Spring Safety Valve, Rubber Seal Ring 24 Pc Roasting Pan , Body Shape:rectangular Material: Stainless Steel Dimension: Length: 40 Cm X Width-35 Cm X Height -7 1/2cm (minimum) Thickness: 1.5 Mm Thick (minimum) Welded Handles On Both Sides Removable Stainless Steel Wire Rack 40 Pc Scissor, Kitchen Type:kitchen Scissor Body Shape: Ergonomic Blade Material: Stainless Steel, 2 Mm Thick Handle Material Heavy Duty Acrylonitrile Butadiene Styrene (abs) Plastic Overall Length: 20 Cm (minimum ) Width: 7.5 Cm (minimum) 30 Pc Siever,small Type: Fine Mesh Siever Body Shape: Round Material: Stainless Steel Diameter: 20 Cm (minimum) Depth: 7 Cm (minimum) Twin Wire Handle: Length 20 Cm X 5 Mm Diameter (minimum) Fine Mesh: 0.7 Mm (1/32 Inch) (minimum) Preferably With A Packing Case 30 Pc Skimmer, Fine Type: Medium Fine Mesh Skimmer Body Shape: Round Material: Stainless Steel, Polished Overall Length: 34 Cm (minimum) Skimmer Head: Diameter -10 Cm X Depth- 4 Cm (minimum) Diameter Of Holes: 2 Mm (approx.) Handle: Length- 12 Cm X Diameter- 2 Cm (minimum) Handle Has Hole For Hanging Preferably With A Packing Case 30 Pcs. Skimmer,spider, Dishwashing Safe Type: Skimmer, Spider Body Shape: Round Material: Stainless Steel, Polished Overall Length: 35 Cm (minimum) Skimmer Head Diameter: 15 Cm X Depth 4 Cm (minimum) Handle Length: 12 Cm X 2 Cm Diameter (minimum) Preferably With A Packing Case Dishwasher Safe. 24 Pcs. Soup Cup, Rack Body Shape: Square Material: Polypropylene Plastic Dimension: Length: 50 Cm X Width: 50 Cm X Height: 10 Cm (minimum) Compartment Length: 11 Cm Compartment Width: 11 Cm Compartment /inside Height: 6.7 Cm No. Of Compartment: 16 Compartments 20 Pc Soup Ladle, 12oz Body Shape: Round Material: Stainless Steel Thickness: 1 Mm Thick (minimum) Handle Length: 34 Cm (minimum) Capacity: 12 Oz. (341 Ml) Ladle Type: Round Bottom Hooked Handle Design Allows It To Easily Sit On The Edge Of Pots. Preferably With A Packing Case Dishwasher Safe 20 Pc Soup Ladle, 3 Oz Body Shape: Round Material: Stainless Steel Thickness: 1 Mm Thick (minimum) Handle Length: 28 Cm (minimum) Capacity: 3 Oz. (85 Ml) Ladle Type: Round Bottom Hooked Handle Design Allows It To Easily Sit On The Edge Of Pots. Preferably With A Packing Case Dishwasher Safe Must Be Branded 20 Pc Soup Ladle 6 Oz. Body Shape: Round Material: Stainless Steel Thickness: 1 Mm Thick (minimum) Handle Length: 30 Cm (minimum) Capacity: 6 Oz. (170 Ml) Ladle Type: Round Bottom Hooked Handle Design Allows It To Easily Sit On The Edge Of Pots. Preferably With A Packing Case Dishwasher Safe 20 Pc Soup Ladle 8 Oz. Body Shape: Round Material: Stainless Steel Thickness: 1 Mm Thick (minimum) Handle Length: 30 Cm (minimum) Capacity: 8 Oz. (236 Ml) Ladle Type: Round Bottom Hooked Handle Design Allows It To Easily Sit On The Edge Of Pots. Preferably With A Packing Case 62 Pc Spatula, Type: Offset Spatula Body Shape: Flat Blade Material: Stainless Steel 316 Handle Material: Hardwood (smooth Finish) With Rivets Blade Dimension: Length= 7 .5 Inches X Width-1.5 Inches (minimum) Thickness Of Blade: 1.7 Mm Thick (minimum) Total Length = 12 To 14 Inches Preferably With A Packing Case Dishwasher Safe Must Be Branded. 400 Pc Spoon, Kitchen Body Shape: Oval Material: Stainless Steel, 1.5 Mm Thick Overall Length: 30.5 Cm X Width-7.5 Cm (minimum) Spoon Head Dimension (l X W) 9 Cm X 7.5 Cm (minimum) Handle: Abs Plastic Spoon Head: Oval Type Preferably With A Packing Case Heat Resistant Up To 220 ° C Dishwasher Safe Must Be Branded. 60 Pc Spoon, Kitchen (slotted) Kitchen Spoon Slotted Body Shape: Oval With Slot Material: Stainless Steel, 1.5 Mm Thick Overall Length: 30.5 Cm X Width-7.5 Cm (minimum) Spoon Head Dimension (l X W) 9 Cm X 7.5 Cm (minimum) 30 Set Spoon, Measuring Body Shape: Bowl In Shape Material: Stainless Steel, 0.7 Mm Thick (minimum) The Set Consists Of The Following Sizes: 1 Pc - 1 Tbsp. (15 Ml) 1 Pc - 1/2 Tbsp. ( 7.5 Ml) 1 Pc - 1 Tsp. (5 Ml) 1 Pc - 1/2 Tsp. (2.5 Ml) 40 Pcs. Spoon, Parisienne Body Shape: Round Double Headed Parisiennes Scoop Bar Tool Material: Stainless Steel, Polished Overall Length: 240 Mm (minimum) Scoop Diameter: 30 Mm And 24mm (minimum) With Plastic Handle (polypropylene), Size: 130 Mm X Width-20 Mm (minimum) Draining Small Hole In The Scoop 40 Pc Spoon, Serving Preferably With A Packing Case Type: Serving Spoon Body Shape: Oval Materials: Stainless Steel Dimension: Length: 23 Cm X Width: 5 Cm (minimum) Scoop Dimension (l X W X D): 7 Cm X 5 Cm X 0.9 Cm (minimum) Spoon Thickness: 1.6 Mm (minimum) Preferably With A Packing Case Dishwasher Safe Must Be Branded. 30 Pc Spoon,wooden Body Shape: Oval Material: Hardwood Dimensions: Length- 10 Inches X Width- 2 Inches (minimum) Bowl Dimension: Length -3 Inches X Width 2 Inches X Depth -3/4 Inches (minimum) Total Length: 10 Inches (minimum) Preferably With A Packing Case Smooth Surface Finished And No Sharp Edges 20 Pc Stock Pot,large . Body Shape: Round Material: Stainless Steel, 0.8 Mm Thick (minimum) Top Diameter: 30 Cm (minimum) Height: 31 Cm (minimum) 30 Pc Strainer, Chinois,small Body Shape: Conical Material: Stainless Steel Strainer Diameter: 20 Cm (minimum) Strainer Depth: 21.5 Cm (minimum) Handle Length: 20 Cm (minimum) With 2 Mm. (approx.) 30 Pc Strainer,chinois,medium Medium Body Shape: Conical Material: Stainless Steel Strainer Diameter: 20 Cm (minimum) Strainer Depth: 21.5 Cm (minimum) Handle Length: 20 Cm (minimum) With 2 Mm. (approx.) 26 Pc Strainer,medium,fine Body Shape: Round Material: Stainless Steel Strainer Diameter: 20 Cm (minimum) Strainer Depth: 7 Cm (minimum) Handle Length: 18 Cm (minimum) With 2 Mm. (approx.) 30 Pc Strainer, Small,fine Body Shape: Round Material: Stainless Steel Strainer Diameter: 13 Cm (minimum) Strainer Depth: 5 Cm (minimum) Handle Length: 13 Cm (minimum) With 1 Mm. (approx.) 30 Pc Tenderizer, Medium Aluminum Meat Tenderizer 16 Pc Thermometer,pocket/pin Pocket/pin Food Thermometer 20 Pc Tong,12'' Body Shape: Standard Material: Stainless Steel Size: 12 Inches Stainless-steel Arms With Soft, Comfortable Grips Nylon Heads Safe For Nonstick Cookware Heat-resistant Up To 400 Degrees Fahrenheit Tongs Lock Closed For Storage Preferably With A Packing Case Food Grade And Dishwasher-safe Must Be Branded 20 Pc Tong 8'' Stainless-steel Arms With Soft, Comfortable Grips Nylon Heads Safe For Nonstick Cookware Heat-resistant Up To 400 Degrees Fahrenheit Tongs Lock Closed For Storage Preferably With A Packing Case Food Grade And Dishwasher-safe Must Be Branded 30 Pc Tray,baking,small, Tray Body Shape: Rectangular Material: Stainless Steel Dimension: 20 Cm X 30 Cm X 3.7 Cm (minimum) 36 Pc Tray,utility,medium,plastic White Plastic, White Multi Purpose 13”x10”utility Tray 30 Pc Turner,3'x6'', Slotted Turner, 3" X 6" Type: Slotted Turner, 3" X 6" Body Shape: Straight Material: Stainless Steel Blade Size (lx W): 6 Inches X 3 Inches (minimum) Handle Length: 5 Inches (minimum) Overall Length: 13 Inches (minimum) Solid Turner With Straight Slotted Blade Wooden Handle With Triple Rivets Preferably With A Packing Case Dishwasher Safe Must Be Branded 4 Pc Utility Cart, Stainless Steel 3 Tier Trolley Cart 75x40x85. 20 Pc Weighing Scale 1 Kg. Digital Type: Digital Weighing Scale Body Shape: Rectangular Materials: Engineering Plastic And Stainless Steel Weighing Plate Capacity: 1 Kg Accuracy: 1 Gram Back Light Lcd Display With 15 Mm Minimum High Digits Weighing Units: Gram, Ounce, Pound Size: (l X W X H Mm ) 163 Mm X 245 Mm X 79 Mmm (minimum) 20 Set Weighing Scale 5kg. Type: Mechanical Weighing Scale Body Type: Circular Bowl Material: Stainless Steel Bowl And Metal Body (coated) Mechanism Type: Spring Lever Capacity: 5 Kg /11 Lb. Sensitivity/graduated By 10 Gm Measurement Units: Gram/kilogram Manual Setting On Zero, Must Be Accurate And Durable Calibrate The Scale Using The Adjustment Knob Preferably With A Packing Case Delivery Must Include Instruction Manual Written In Good English With Service Centers Located In The Major Cities In The Philippines Warranty Period Of 1 Year (parts And Service) Must Be Branded 40 Set Wire Skimmer Small, Type: Skimmer, Wire Mesh Body Shape: Round Material: Stainless Steel, Polished Overall Length: 40 Cm (minimum) Skimmer Head Diameter: 12 Cm (minimum) Diameter Of Holes: 2 Mm (approx.) Handle Has Hole For Hanging Preferably With A Packing Case Dishwashing Safe Must Be Branded. 40 Pc Wire Whisk Heavy Duty Type: Wire Whisk, Heavy Duty Body Shape: Ballon Material: Heavy Duty Stainless Steel Dimensions (l X W): 31.8 Cm X 7.6 Cm (minimum) Handle Length: 12 Cm (minimum) With Hanging Loop No. Of Wires: 8 Wires Wire Diameter: 2 Mm (minimum) Preferably With A Packing Case Dishwasher Safe Must Be Branded. 40 Pc Wire Whisk, Medium, Type Wire Whisk, Medium Body Shape: Ballon Material: Stainless Steel Wire Whisk Medium Dimensions (l X W): 25.4 Cm X 7 Cm (minimum) Handle Length: 10 Cm (minimum) With Hanging Loop No. Of Wires: 6 Wires Wire Diameter: 1.8 Mm (minimum) Preferably With A Packing Case Dishwasher Safe Must Be Branded. 40 Pc Wire Whisk,small, Type: Wire Whisk, Small Body Shape: Baloon Material: Stainless Steel Wire Whisk Medium Dimensions (l X W): 20.3 Cm X 6 Cm (minimum) Handle Length: 10 Cm (minimum) With Hanging Loop No. Of Wires: 6 Wires Wire Diameter: 1.8 Mm (minimum) Preferably With A Packing Case Dishwasher Safe Must Be Branded. 18 Pc Wok,medium Type: Wok, Medium Body Shape:round Material: Carbon Steel Thickness: 1.8 Mm Thick (minimum) Dimensions (dia. X H): 45 Cm X 14 Cm (minimum) Handle Material: Steel Riveted Convenient Both Side Handle 10 Cm (minimum) With Flat Bottom Preferably With A Packing Case Dishwashing Safe Must Be Branded 18 Pc Wok,small Type: Wok, Small Body Shape: Round Material: Carbon Steel Thickness: 1.5 Mm Thick (minimum) Dimensions (dia. X H): 36 Cm X 10 Cm (minimum) Handle Material: Steel Riveted Convenient Both Side Handle 8 Cm (minimum) With Flat Bottom Preferably With A Packing Case Dishwashing Safe Must Be Branded 12 Pc Working Table, Stainless, 4 Seaters Stainless Working Table , Two Layer (120x60x80) 30 Pc Zester, Type: Cheese Zester Body Shape: Standard Material: Stainless Steel Grating Surface Dimensions (l X W): 20.3 Cm X 4 Cm (minimum) Overall Length: 32.5 Cm (minimum) Handle Material: Plastic (polypropylene) Ergonomic Handle Preferably With A Packing Case Dishwasher Safe The Plastic Material Used Must Be Non-toxic Must Be Branded. Lot 6. Sumirap National High School (housekeeping Nc Ii)-php 326,452.00 1 Pc Alarm Clock Alarm Clock, Digital, Overall Dimensions: 13.5 X 8 X 4.5 Cm (approx.) Material: Plastic (pe/abs) Illuminated Lcd Digital Display: Time (12/24), Calendar (mm/dd), Temperature, Alarm Status (on/off), Snooze Display Size: 10 X 5 Cm (minimum), Time Can Be Read 30 Ft Day Time. Runs On Aaa Battery Which Come Together With The Item Smooth Surface, No Sharp Edges, Includes User's Manual Which Contains Operation Procedure, Name Of Parts, Safety Precautions, Trouble Shooting) 25 Pc Apron, Polyester-cotton (bib Apron, Sleeveless Adjustable Neck Loop Material : Polyester - Cotton Fabric Dimension : 70 To 60 Cm (minimum) With 2 Or 3 Pockets Uni-color, Dark No Sharp Edges And Loose Threads) 5 Pc Baskets, Laundry (3 - Bag Laundry Sorter, With Wheels Bag: Polyester, Rectangular Shape, Detachable From Frame With Metal Handle And Hanging Hook Bag Dimensions : Rectangular 22 X 15 X 8 Inch (minimum) Frame Material : Corrosion Resistant Steel, Sturdy No Wobble Frame Overall Dimensions : Rectangular, 31 X 30 X15 Inch (minimum) With Four Casters, 2 Inch Diameter (minimum) Smooth Surface, No Sharp Edges) 1 Set Bed, Queen (bed Set, Queen Size (60 X 75 Inch) Rectangular 1) Frame: Knock-down Type, All Steel, Powder Coated Including Head Board, Bare Weight: 20 Kg (minimum) No Wobble And Noise 2) Comes With Fabric Covered Foam 6 Inches Thick Foam Density: 29 -33 Kg/cu.m. 3) No Sharp Edges) 1 Set Bed, Single (bed, Single Size (w36 X L75 Inch) Rectangular 1) Frame: Knock-down Type, All Steel, Powder Coated Including Head Board, Bare Weight: 13 Kg (minimum) No Wobble And Noise 2) Comes With Fabric Covered Foam 6 Inches Thick Foam Density: 29 -33 Kg/cu.m. 3) No Sharp Edges) 10 Pc Board, Ironing (type: Foldable Type Ironing Board Body Shape : Standard Material : 25 Mm Tubing Approx., 0.8 Mm Thickness Board Size: 32 Inches (minimum ) Body Size :120 Cm X 30 Cm X 5 Cm Color : Any Comes With Box No Sharp Edges) 25 Pair Boots, Safety, Plastic (upper Material: Elastic Pvc Sizes: 7 Inches - 5pcs 8 Inches - 5pcs 9 Inches - 5pcs 10 Inches -5pcs 11 Inches - 5pcs Height: 13 To 14 Inches Plain Toe Type Of Boots: Unisex Rain Boots With Rugged Tractor Lug Outsole Packed With Carton Box Per Size) 15 Pc Brushes, For Housekeeping (brush, Floor Scrubbing, Angled Long Handle Bristle Material : Plastic, Stiff Handle Material : Metal Tubular Corrosion Reistant, Overall Length : 120 Cm. (minimum) Bristle Length : 5 Cm (=/- 1cm) Scrubbing Surface : 25 X 6 Cm (+/-1 Cm) No Sharp Edges) 10 Pc Buckets, Water (water Bucket Bucket Material : Hard Plastic, Round Body Capacity : 10 To 12 Liters Handle Material : Steel Smooth And Glossy Surface, No Sharp Edges) 10 Pc Caddy, Toilet (carrying Caddy For Toilet Cleaning Supplies Holds Spray Bottles And Other Cleaning Supplies, No. Of Compartments: 3 (minimum) Material :plastic Tray Depth: 11 Cm (approx.) Overall Dimension: 36 X 26 Cm (approx.) Smooth Surface, No Sharp Edges) 1 Unit Carpet Sweeper (carpet Sweeper, Cordless Electric Motorized Single Brush Roll (removable) Body Material : Hard Plastic ,(abs) Or Its Equivalent, Any Color Equipped With Rechargeable Battery (16 Minutes Run Time On Carpet), Removable Dirt Box Sweep Width : 8 Inches (minimum) Capacity (volume) : 0.35 Lit.(minimum) Handle: Metal, Powder- Coated, With Plastic/rubber Grip, Swivel Steering Assembled Height: 44 Inches (minimum) Comes With Battery Charger 220/240vac, 50/60hz With Plug To Adapt Type A Outlet (or Providing 3a Minimum Plug Adapter Is An Option) No Sharp Edges Includes User's Manual Which Contains Operation Procedure, Name Of Parts, Safety Precautions, Trouble Shooting.) 1 Unit Cart, For Housekeeping Nc Ii (housekeeping Cart Trolley, Equipped With Three-shelves With Steel/laminated Panels Single Door, Top Layer With Divider, Bag Holder, And 4 Wheels. Cart Frame: Steel, Powder Coated. Wheels: 2non-swivel 2 Swivel, 6 Inch Diameter, Non-markings. Overall Dimensions : Rectangular 90 X 48 X 1010 Cm (minimum) Comes With Accessory Linen Bag Smooth Surface, No Sharp Edges) 50 Pc Cleaning Cloth, Linth-free (lint Free Cleaning Cloths Material : Cotton Dimensions : Rectangular 16 X 26 Inch) 1 Unit Coffee Maker (coffee Maker, Electric Material: Metal, Plastic, Glass. Capacity: 6 Cups (minimum). Detachable Tank, With Water Level Indicator. Non-stick Warming Plate : Removable And Washable Filter Non-drip Valve : Lighted On/off Switch Power Supply: 220 V -240 V Ac 50/60 Hz , 500w Minimum Comes With A Heat Resistant Glass Pitcher. With A 1 Meter (minimum) Power Cord, Molded Male Plug To Adapt Type A Outlet (or Providing 5a Minimum Plug Adapter Is An Option). Smooth Surface, No Sharp Edges With Dti-bps Certification, Brand And Electrical Ratings Clearly And Permanently Mark On The Item. Comes With English Manual That Contains: Users Guide, List Of Parts, Maintenance Guide, Safety Guide. 1 Year Warranty Parts And Service With Service Centers Located In Major Cities In The Philippines) 5 Pc Dust Pan (dust Pan, Upright Standing Material: Plastic Overall Length: 65 Cm (minimum) Pan: Round Back, 24 X 26 X 9 Cm (minimum) Smooth Surface, No Sharp Edges) 5 Pc Duster, Anti-static (anti-static Duster Duster Material : Polypropylene Micro Fiber Duster: Length : 30 Cm (minimum), Overall Length: 50 Cm (minimum) Handle Material : Hard Plastic, No Sharp Edges) 7 Unit Fan, Electric ( Stand Fan, Electric Material: Metal, Plastic Size/diameter: 18 Inches Power Rating: 70 Watts (minimum), 220 / 240 Vac, 50 / 60 Hz, Single Phase Rotation Angle: 90 Degrees Base: Stable, 16 Inches Diameter (approx.) Removable Metal Guard On Front And Rear 3-speed Settings Comes With 1.5 Meters Power Cord And With Molded Male Plug To Adapt Type A Outlet (or Providing 3a Minimum Plug Adapter Is An Option) Smooth Surface, No Sharp Edges Includes User's Manual In English Which Contains: A. A Diagram Of The Parts With Their Names, B. Operating Procedures On How To Use The Equipment, C. Safety Precautions When Using The Equipment, D. Basic Troubleshooting And Maintenance Procedures With Dti-bps Certification, Brand And Electrical Ratings Clearly And Permanently Mark On The Item 1 Year Warranty Parts And Service) 3 Pc Fire Extinguisher(with Contents) (1.for Type A, B, C Fire: Dry Chemicals (monoammonium Phosphate) 2.portable Type 3.capacity : 5 - 6 Kgs 4.rechargeable Cylinder Metal 5.working Pressure Of Cylinder : 400 Psi 6.brass Valve With Pressure Gage 7.with Rubberized Hose And Aluminum Nozzle Attached 8.with Squeeze Lever To Discharge And Safety Pin 10.painted With Metal Primer And Red Enamel Paint 11.includes With User's Guide In English That Contains: A. Operating Procedure On How To Use The Equipment B. Safety Precaution When Using The Equipment 12.1 Year Warranty Parts And Service 13.the Item Must Be Branded And Have Good Quality) 10 Pc Flashlight (flashlight Led 1,000 Lumens (minimum), Color : White , Battery: Rechargeable, At Least 3,500 Mah , Can Be Used Also With 3 X Aaa Batteries; Body: Aluminum Alloy, No Sharp Edges Dimensions : 5 Inches X 1 Inch Diameter (minimum) Operating Duration Of Battery When Fully Charged : At Least 2 Hours; Includes 220/240vac, 50/60hz Power Adapter /charger And User's Manual In English Which Includes: A. A Diagram Of The Parts With Their Names, B. Operating Procedures On How To Use The Equipment, C. Safety Precautions When Using The Equipment, D. Basic Troubleshooting And Maintenance Procedures Branded, With 1 Year Warranty 10 Pc Flat Iron (clothes Flat Iron, Electric Material : Metal /plasic Body, Heat-resistant Plastic Handle, Aluminum Sole Overall Dimension : (l X W X H) 25 Cm X 12 Cm X 12 Cm (minimum) Power Rating : 220/240 Vac, 50/60 Hz; 1000 Watts (minimum) Equipped With Light Indicator, Variable Temperature Control, Overheat Protection, Power Cord And Plug To Adapt Type A Outlet (or Providing 10a Plug Adapter Is An Option) Smooth Surface, No Sharp Edges, Comes With English Manual That Contains : Users Guide, List Of Parts, Maintenance Guide, Safety Guide. The Item Must Be Branded, With Dti-bps Certification 1 Year Warranty Parts And Service With Service Centers Located In Major Cities In The Philippines.) 10 Pc Foam, Scrubbing (1. Material: Cellulose And A Scouring Pad On One Side 2. Dimension: Length : 140 - 180 Mm ; Width : 80 - 100 Mm ; Thickness : 12 - 20 Mm 3. The Item Must Be Of Good Quality) 4 Pc Garbage Receptacles (1.bucket / Tub Material : Hard Plastic, (ps) Polystyrene 2.bucket / Tub Color : Any Color 3.capacity (gallons) : 3 Gal. (minimum) Comes With A Cover 4.the Item Must Have Good Quality) 30 Pair Gloves, Rubber (1.heavy-duty Latex-free Vinyl Rubber Gloves 2.thickness : 4 Mil 3.color : Any Color 4.size : Medium 5.other Features: Acid/solvent Resistant. 6.the Item Must Be Of Good Quality) 15 Pc Goggles, Safety (safety Goggles, Clear Polycarbonate - One Piece Lens With 180° Panoramic View, Non-fog Size/dimension: L 17 - 18.5 Cm X W 8 Cm X D 5-7.5 Cm High Impact Resistant, Ansi "z87" Compliant Firm And Comfortable Seal Around Forehead, Cheeks, Nose And Temples Protects Against Splash, Chemicals, Dust Adjustable Head Strap Shall Bear Mark Z87 Embossed Or Engraved Or Etched On The Item. Smooth Surface, No Sharp Edges) 1 Pc Hairdryer( Electric Hairdryer, With Concentrator Nozzle Two Heat Setting And 1 Speed (minimum) Rating : 220/240 Vac, 1200 W (minimum) Body Length Including Nozzle: 20 Cm Folding Handle Design, With Hanging Ring Smooth Surface, No Sharp Edges Branded, Brand Name And Electric Rating Permanently Mark On The Item, With Dti-bps Certification With User's Manual Written In English That Contains Operating Procedure, Parts With Description, Safety Procedure, And Maintenance. With Service Centers Located In Major Cities In The Philippines. 1 Year Warranty(parts & Service) 2 Roll Hose, Water(water Hose Material: Pvc Fiber Reinforced, Three (3) Layers; Any Color; Hose Length: 50 Feet; Hose Diameter: 5/8 Inches; Pressure Capacity: 200 Pounds Per Square Inch (minimum); Fitted With Male And Female Brass Couplers (nh, 11.5 Tpi) For Spray Nozzle No Sharp Edges) 3 Pc Kettle, Electric(electric Kettle Cordless (with Pouring Spout), Hinged Lid, Detachable From And Can Rotate On Its Corded Base Material : Round Stainless Body, Plastic Handle, Lid And Base Capacity : 1.5 To 2 Liter Automatic Shut - Off, With Power Indicator Light Power Rating: 220//240vac, 50/60hz, 1000 -1600 Watts Base With A 50 Cm (minimum) Power Cord, Molded Male Plug To Adapt Type A Outlet (or Providing 10a Plug Adapter Is An Option) Smooth Surface, No Sharp Edges; Dti-bps Certified Comes With English Manual That Contains: Operation Procedure, Maintenance And Safety Guide. The Item Must Be Branded, Brand Name And Electrical Ratings Permanently Mark On The Item.) 5 Pc Laundry Sorter(3 - Bag Laundry Sorter, With Wheels Bag: Polyester, Rectangular Shape, Detachable From Frame With Metal Handle And Hanging Hook Bag Dimensions : Rectangular 22 X 15 X 8 Inch (minimum) Frame Material : Corrosion Resistant Steel, Sturdy No Wobble Frame Overall Dimensions : Rectangular, 31 X 30 X15 Inch (minimum) With Four Casters, 2 Inch Diameter (minimum) Smooth Surface, No Sharp Edges) 2 Pc Light, Emergency(emergency Light, 2 Heads Led Materials: Metal, Anti-rust Coated Duration Time (2 Heads): 5 Hours (minimum) Automatically Light Up During Power Outage Overcharge And Over- Discharge Protection Built - In Ac Charger, Power Cord Plug To Adapt Type A Outlet (or Providing 5a Minimum Plug Adapter Is An Option) Battery Test Switch - External Safety Fuse Head: White Led 1w (minimum) 3.5 " Dome Reflector Power Rating: 220 -240 Vac , 50/60 Hz 20-24 Hours Charge Time Dimensions: Rectangular 27 X 7 X 27 Cm (approx.) Sooth Surface, No Sharp Edges Includes User's Manual In English Which Contains: A. A Diagram Of The Parts With Their Names, B. Operating Procedures On How To Use The Equipment, C. Safety Precautions When Using The Equipment, D. Basic Troubleshooting And Maintenance Procedures The Item Must Be Branded, Brand Name And Electrical Ratings Permanently Mark On The Item.) 2 Pc Mirror Wall Mirror With Frame Flat Glass Mirror, 2 Mm Thick (minimum), Clear With No Distortion Frame: Wood Or Plastic Commercial Finish Rectangular Shape, 3600 Sq.cm (minimum) Includes Mounting Accessories Smooth Surface, No Sharp Edges) 20 Pc Mop (mop, Handle And Mop Head Set, Refillable Head Handle: Aluminum Or Anti-rust Coated Steel, With Hard/stiff Plastic Mop Head Holder, Clip Type With Tightening Knob Overall Handle Dimension: 130 X 19 Cm (minimum) Mop Head: Cotton Thread/yarn, Sewn Tailband, L 34 X 16 X 4 Cm (minimum), White Handle: Plated Steel Tube Or Wood, Length : 40 (minimum), No Sharp Edges 1 Set Polisher, Floor, Electric, With Accessories(electric Floor Polisher With Accessories Material: Stainless Steel, Aluminum Alloy Handle: Stainless Tube, Adjustable Height 1 Meter Long (approximate), With Dual Switch Lever Size/capacity :13 Inch (minimum) Diameter Power Supply: 220/240 Vac, 50/60 Hz. Power: 1/3 Hp (minimum) Rotation Speed : 160 Rpm (minimum) Heavy Duty (royal) Power Cord Length : 12 Meters (minimum) With Type A Plug (or Providing 10a Plug Adapter Is An Option) With Pair Of Rubber Wheels, Smooth Surface, No Sharp Edges Comes With Pad Holder, 2 Pcs - Polishing Brush And 3 Pcs - Floor Polishing Pads Includes User's Manual In English Which Contains: A. A Diagram Of The Parts With Their Names, B. Operating Procedures On How To Use The Equipment, C. Safety Precautions When Using The Equipment, D. Basic Troubleshooting And Maintenance Procedures Branded, Brand Name And Electric Rating Permanently Mark On The Item, With 1 Year Warranty Parts And Service The Offered Brand Of The Item Must Be An International Brand With At Least 5 Years Presence At The Local Market And Global Presence In The Usa, Europe Or In Japan Market.) 5 Pc Shelving(shelving, Open, Knockdown Type, Adjustable Shelves Metal Powder Coated Frame Number Of Shelves : 5 Overall Dimensions : 85 X 30 X 180 Cm(minimum) Sturdy Connection, No Wobble Smooth Surface, No Sharp Edges) 5 Pc Sign, Caution(caution Sign, A Shape-2 Panel Self Standing, With D-handle, Collapsible For Easy Storage Material : High Impact Plastic, Panel Dimension : Rectangular (lxw) 55-65 Cm X 25 X 61 0m (minimum), Panel Depth : 2 Cm (minimum) Color : Yellow Print Description : "caution: Wet Floor" On One Side "cleaning In Progress On The Other Side, Both Messages Provided With Graphics Printed In Black. Font Size: 100 -120 Mm X 50 -70 Mm, Arial Smooth Surface, No Sharp Edges) 10 Pc Sponges, Dish(dish Sponge, Cellulose, Non-scratch Dimensions : 5 X 3 X 1 Inch (minimum) Branded) 10 Pc Spray Gun, Water(barber/salon Spray Gun Material: Hdpe Transparent Plastic Capacity: 300 Ml.(minimum) Trigger Type Sprayer Dimension: Diameter :7 Cm. X Height: 16.3 Cm (minimum) Rotating Nozzle To Adjust Spray Patterns Smooth Surface, No Sharp Edges Must Be Branded) 10 Pc Squeegee(squeegee, Short Handle Head/blade Material: Stainless, Rubber Handle: Plastic Or Stainless Steel Blade Length: 25 - 30 Cm Overall Length (handle And Head) 20 - 32 Cm No Sharp Edges ) 5 Pc Squeezer, Mop(mop Bucket With Squeezer/wringer And Wheels Hand Lever To Squeeze, Made Of Metal, With Hand Grip Material : Hard Plastic, (ps) Polystyrene Or Its Equivalent Capacity : 30 L (minimum) Overall Dimension (excluding Handle: ( L X W X H ) 40 X 27 X 57 Cm (minimum) Color : Yellow With 3 Inches Non-marking Rubber Casters "caution" Printed In Black On Both Sides Of The Mop Bucket Smooth Surface, No Sharp Edges) 1 Pc Step Ladder(material: Aluminum U Channel Capacity: 250 Lbs (minimum) Type: Flatform Type Number Of Step: 6 (including Top Step) Reach Height: 6 To 8 Feet(minimum) Width: 15 Inches Minimum Spread: 4 Feet (minimum) Twin Steps With Gripped Treads To Prevent Slipping Step Braces On Top And Bottom Step Heavy Duty Aluminum Foot Bracket With Slip-resistant Foot Pad With User's Manual In English Which Includes: A. Parts Manual With Labels, B. Assembly Instructions, Brandedfeet(minimum) Width: 15 Inches Minimum Spread: 4 Feet (minimum)) 2 Pc Vacuum Cleaner, Dry And Wet(electric Vacuum Cleaner, Wet And Dry Function, Sucks Even Screws, With 4 Swivel Caster Wheels Material : Hard Plastic, (abs) Or Rust Proof Body Equivalent Power Supply : 220/240vac, 50/60hz, 1000 Watts (minimum) Auto Shut Off Tank Capacity : 20 Liters (minimum) Equipped With Complete Accessories I.e., Detachable Vacuum Hose Assembly (flexible Non-kink), Extension Tubes/wands, Carpet (long Square) Brush Nozzle, Wet And Dry Floor Brush Nozzle, Crevice Nozzle, Hepa Filter, Sponge Filter/washable Cloth Bag. Comes With 4 Meters (minimum) Heavy Duty (royal) Power Cord, Molded Male Plug To Adapt Type A Outlet (or Providing 10a Plug Adapter Is An Option) Smooth Surface, No Sharp Edges With User's Manual Written In English That Contains Operating Procedure, Parts With Description, Safety Procedure, And Maintenance. The Item Must Be Branded, Brand Name And Electric Rating Permanently Mark On The Item. 1 Year Warranty Parts And Service With Service Centers Located In Major Cities In The Philippines. The Offered Brand Of The Item Must Be An International Brand With At Least 5 Years Presence At The Local Market And Global Presence In The Usa, Europe Or In Japan Market.) 1 Unit Washer, Laundry(1. Front Load Electric Washer, Laundry 2. Electronic Control, Digital Indicator Display , Transparent Glass Door 3. Body Material : Steel, Powder Coated, Any Color 4. Dimensions (wxdxh): 590 Mm (minimum) X 490 Mm (minimum) X 820 Mm (minimum) 5. Drum Material : Stainless Steel 6. Capacity : 8 Kg (minimum) 7. Spin Speed : 1200 Rpm (minimum) 8. Power Rating: 220 /240vac, 50/60 Hz. 9. Comes With A 1 Meter (minimum) Heavy Duty Power Cord With Male Plug To Adapt Type A Outlet (or Providing 20a Plug Adapter Is An Option) 10. Smooth Surface, No Sharp Edges 11. With Dti-bps Certification, Brand And Electrical Ratings Clearly And Permanently Mark On The Item 9.includes User's Manual In English Which Contains: A. A Diagram Of The Parts With Their Names, B. Operating Procedures On How To Use The Equipment, C. Safety Precautions When Using The Equipment, D. Basic Troubleshooting And Maintenance Procedures 12.the Item Must Be Branded, Dti-bps Certified, 1 Year Warranty Parts And Service 13. With Service Centers Located In Major Cities In The Philippines. 14.the Offered Brand Of The Item Must Be An International Brand With At Least 5 Years Presence At The Local Market And Global Presence In The Usa, Europe Or In Japan Market.) 2 Pc White Board(white Board, Floor Standing, Rolling Board: White Formica Laminated, Plane Will Not Deform. Board Size: Rectangular 1800mm W X 1000 To 1200mm H, Board Edges Secured With Aluminum Clip Edging 17 Mm (minimum) Wih Plastic Corner Caps Comes With Metal Tray For Marker And Eraser The Stand And Frame Are Constructed With Aluminum Or Powder Coated Steel 25mm Square Tube (minimum), Sturdy, No Wobble With 4 Lockable Hard Plastic Caster Wheels Overall Height From Floor: 210 To 214cm Smooth Surface, No Sharp Edges) Lot 7. Tangub City National High School (food And Beverage Services Nc Ii) Php 571,245.00 50 Pcs Chair, Dining Type : Dining Side Chair Body Shape: Square Material : Metal (round Or Square) Dimesion: Total Height - 33" X 15" X15" (minimum) Capacity: 150 Kg. Black Colored Powder Coated Frame With Foam On Seat Packed In Carton Box The Item Must Have Good Quality 4 Pcs Coffee Pot, 2 Pints Type: Manual Drip Body Shape: Round Material : Stainless Steel With Cover Capacity : 2 Pints Outside Diameter : 90 -110 Mm Over-all Height : 200 - 230 Mm Thickness : 0.5 - 1 Mm With Handle And Spout Packed In Carton Box The Item Must Have Good Quality 6 Pcs Container, Creamer Design: Type: Porcelain With Spout Body Shape: Circular Material: Porcelain Diameter : 50 - 65 Mm Height : 80 - 105 Mm Color : White Appearance : Glossy White Packed In Carton Box The Item Must Have Good Quality 24 Set Cups Ans Saucers 5-6 Oz. 1. Material : Porcelain 2. Capacity : 5 Oz./140 Ml 3. Heatproof Up To 300 Deg. C 4. Color : White 5. The Item Must Be Of Good Quality 6. Packed In Carton Box 10 Pcs Folder, Menu Type: Leather Menu Folder Body Shape: Rectangular Material: Leather With 2 Partitions And 6 Inserts Size: 31.5cm X 24.5cm Color: Brown/black Applicable Paper Size: A4 50 Pcs Fork, Cocktail 1. Material/appearance: Stainless Steel, Highly Polished, W/ Plain Design 2. Type : Rounded Tip Handle 3. Over-all Length : 110 - 165 Mm 4. Width : 20 - 30 Mm (minimum) 5. Handle Thickness : 2 Mm To 4 Mm 6. Handle Length : 75 - 90 Mm 7. Small, 8. Color : Silver 9. The Item Must Be Branded And Have Good Quality. 50 Pcs Fork, Dessert Type : Dessert Fork Body Shape: Fork Shape, Round Tip Material/appearance : Stainless Steel, Highly Polished,with Plain Design, Rounded Tip Handle Length : 150 Mm - 175 Mmwidth : 20 - 30 Mmhandle Thickness : 1.5 Mm - 3 Mm Number Of Tines : 4 Handle : 130 Mm (minimum) Color : Silver Packed In Plastic Pouch The Item Must Be Of Good Quality 60 Pcs Fork, Dinner Type: Dinner Fork Body Shape: Fork Shape Material / Appearance : Stainless Steel, Highly Polished, With 4 Tines Over - All Length : 120 - 175 Mm Thickness Of Handle : 2 - 3 Mm Color : Silver Packed In Plastic Pouch The Item Must Be Of Good Quality 36 Pcs Fork, Fish Type : Fish Fork Body Shape: Fork Shape With Round Tip Material / Appearance : Stainless Steel, Highly Polished, With Plain Design Over-all Length : 180 - 215 Mm Fork Width : 1.5 Mm - 3 Mm Fork Thickness : 1 Mm - 2 Mm Number Of Tines : 4 Length Handle : 120 - 130 Mmhandle Thickness : 2 Mm - 3 Mm Color : Silver Packed In Plastic Pouch The Item Must Be Of Good Quality 36 Pcs Fork, Oyster Type: Oyster Fork Body Shape: Fork Shape Material: Stainless Steel, With High Polish Appearance, And With Plain Design Length: 90 - 120 Mm Thickness: 1 Mm - 3 Mm Silver Color With Three Short Wide Curved Tines Packed In Plastic Pouch The Item Must Be Of Good Quality 24 Pcs Glass, Champagne Flute Type : Flute Glass Body Shape: Round Material: Clear Crystal Glass Dimension : Height: 20 -24 Cm, Top Diameter: 50 -70 Mm, Bottom Diameter: 60 - 80 Mm Capacity: 250 Ml. (minimum) Thickness: 1.5 - 3 Mm Packed In Carton Box The Item Must Have Good Quality 36 Pcs Glass, Collins Type: Tumbler Body Shape: Round Material : Clear Glass Capacity : 10 Oz To 14 Oz Thickness : 1.5 -3 Mm (minimum) Packed In Carton Box The Item Must Have Good Quality 36 Pcs Glass, Juice/hi-ball 1. Material : Clear Glass 2. Type : Hi-ball 3. Height : 140 - 160 Mm 4. Bottom Diameter : 50 -70 Mm 5. Top Diameter : 50 - 70 Mm 6. Thickness : 2 - 4 (minimum) 7. Capacity : 8 Oz. To 10 Oz. 8. Diswasher Safe 9. The Item Must Be Branded And Good Quality 10. Packed In Carton Box 36 Pcs Glass ,pilsner(ice Tea Glass) Type:falired Rim,body Shape:round Slender Bowl,material:clear Glass Capacity:20 0z To 23 Oz With Flaired Rimand Slender Shape Packed In Carton Box.the Item Must Have Good Quality. 36 Pcs Glass, Red Wine Type: Royalty Body Shape: Balloon Shaped Bowl Material: Crystal Clear Glass Rim Diameter : 55 - 60 Mm Thickness : 1.5 Mm - 3 Mm Over - All Length : 200 -220 Mm Capacity : 250 -300 Ml Stem Diameter : 6 - 8 Mm Stem Length : 85 - 90 Mm Base Diameter : 75 - 85 Mm Base Thickness : 2 - 4 Mm 40 Pcs Glass, White Wine Type: Royalty Body Shape: Balloon Shaped Bowl Material: Crystal Clear Glass Rim Diameter : 55 - 60 Mm Thickness : 1.5 - 3 Mm Over -all Length : 200 -220 Mm Capacity : 270 - 300 Ml Stem Diameter : 6 - 8 Mm Stem Length : 75 - 85 Mm Base Diameter : 70 - 80 Mm Base Thickness : 2 - 5 Mm 4 Pcs Gravy Boats Type: Steel Type Body Shape: Boat Shape With Handle Material: Stainless Steel Capacity : 5 Oz. Appearance: Mirror Polish Finish Size :17cm X 7.3cm X 8.2 Cm / 6.7 X 2.9 X 3.2 Inches (minimum) The Item Must Have Good Quality Packed In Plastic Pouch 4 Pcs Ice Bucket, 2 Liters With Tongs Type: Steel Type Body Shape: Circular Set Includes: A. Ice Bucket Material : Stainless Steel Diameter : 140 - 180 Mm Height : 140 - 170 Mm Thickness Of Bucket : 0.7 - 2 Mm Capacity : 2 Liters (minimum) The Item Must Have Good Quality 24 Pcs Knife, Butter 1. Material : Stainless Steel W/ Highly Polished Appearance 2. Over-all Length : 140 Mm - 150 Mm 3. Handle Thickness : 3 Mm - 5 Mm 4. With Dull Edge And Rounded Tip 5. The Item Must Have Good Quality. 6. Packed In Carton Box 24 Pcs Knife, Dinner Type: Dinner Knife Body Shape: Flat With Round Tip Material / Appearance : Stainless Steel Blade Highly Polished Handle Material : Stainless Steel Overall Length : 160 - 190 Mm Blade Thickness : 2 - 4 Mmhandle Thickness : 3 - 6 Mm Serrated Blade With Rounded Tip Packed In Carton Box The Item Must Have Good Quality 24 Pcs Knife, Fish Type : Fish Knife Body Shape: Flat With Pointed Tip Material / Appearance : Stainless Steel, Highly Polished W/ Plain Design Overall Length : 200 - 220 Mm Width Blade : 20 - 25 Mm Thickness Of Blade : 2 Mm - 4 Mm Thickness Of Handle: 3 Mm - 6 Mm Wide Blade, Dull Edge, Tip Made With A Notched Point Color : Silver Packed In Carton Box The Item Must Have Good Quality 20 Pcs Napkin Holder (stainless) Type: Steel Type Body Shape: Rectangular Material : Stainless Steel With Highly Polished Appearance Dimension : Width : 70 - 90 Mm X Length : 150 - 170 Mm , Thickness : 0.7 Mm -2 Mm Packed In Plastic Pouch The Item Must Have Good Quality 20 Pcs Order Pads Type: Numbered Pads Body Shape: Rectangular Material : 80 Gsm Offset Paper Each Pad Comes With A 100 Sheets And Corresponding Copy Page Each Pad Has Sequentially Numbered Orders To Make It Easy To Keep Track With 100 Sheets Per Pad And 10 Pads Included Can Take 1000 Orders Before You Run Out Packed In A Plastic Pouch 12 Pc Pepper And Salt Mill Type: Pepper & Salt Mill Body Shape: Round Body Material: Wood Size: Diameter: 5 Cm X Height: 20 Cm (minimum) Carved Of Wood With Stainless Steel Grinding Mechanism Color: Natural Screw Cap At The Top Of The Mill To Adjust The Thickness Of Peeper Or Spices Preferably With A Packing Case Food Grade And Nontoxic Must Be Branded 50 Pc Plate Covers Type: Steel Type Body Shape: Circular Material: Stainless Steel, Mirror Polished Diameter: 10 1/4 Inches (minimum) Height: 2 7/8 Inches (minimum) Thickness: 1/16 Inch. (minimum) With Handle Packed In Plastic Pouch The Item Must Have Good Quality 50 Pc Plate, Dessert, 7" To 8" Type: Plain Type Body Shape: Circular Material: Porcelain Supply Must Be A Set, Consisting Of One (1) Of Each: 7 Inches And 8 Inches Plates Color : White Inner Diameter: 145 To 165 Mm Thickness : 3 To 6 Mm Smooth And Glossy Surfaces Packed In Carton Box The Item Must Have Good Quality 60 Pc Plate, Dinner, 10" Type: Plain Type Body Shape: Circular Material: Porcelain With No Design Color: White Inner Diameter : 200 Mm - 215 Mm Outer Diameter : 250 - 260 Mm Thickness : 3 Mm - 6 Mm Smooth And Glossy Surfaces Packed In Carton Box The Item Must Have Good Quality 50 Pcs Plate, Fish, 8" To 9" Type: Plain Type Body Shape: Circular Material : Porcelain With No Design Supply Shall Be A Set Consisting Of: One (1) Each 8 Inches And One (1) Each, 9 Inches Color : White Inner Diameter : 165 Mm - 190 Mm (minimum) Thickness : 3 Mm - 6 Mm Smooth And Glossy Surfaces Packed In Carton Box The Item Must Have Good Quality 10 Pcs Round Table (8's) Type: Foldable Body Shape: Round Material: High Density Polyethylene Table Top Powder Coated Steel Frame Size: 154cm X 74cm X4.5cm (minimum) Good For 8 To 10 Seater Capacity Tube Size : 28 Mm Diameter X 1 Mm Thickness Packed In A Carton Box The Item Must Have Good Quality 50 Pcs Salad Forks Type: Salad Fork Body Shape: Fork Shape Material/appearance: Stainless Steel, Highly Polished, With 4 Tines Length: 150 Mm - 175 Mm Thickness Of Handle : 2 Mm - 3 Mm Color: Silver Packed In Plastic Pouch The Item Must Be Of Good Quality 50 Pcs Salad Knife Type: Salad Knife Body Shape: Semi Rectangular Blade With Pointed Tip Material/appearance: Stainless Steel, Highly Polished, W/ Plain Design Overall Length: 145 -160 Mm Blade Thickness: 2 Mm To 4 Mm Handle Thickness: 4 Mm To 6 Mm Handle Material: Stainless Steel Rounded Tip Handle Packed In Carton Box The Item Must Have Good Quality 50 Pcs Salad Plates 7" To 8" Type: Plain Type Body Shape: Circular Material: Porcelain With No Design Supply Must Be A Set Consisting Of One (1) Each: 7 Inches And 8 Inches Plates Color: White Diameter (inner): 150 Mm - 165 Mm Thickness: 3 Mm - 6 Mm Smooth And Glossy Surfaces Packed In Carton Box The Item Must Have Good Quality 20 Pcs Salt And Pepper Shakers Type: Glass Type Body Shape: Square Material: Glass And Aluminum Over-all Height: 75 -90 Mm Length: 50 -60 Mm Width: 50 -60 Mm Aluminum Cover Packed In Carton Box The Item Must Have Good Quality 25 Pcs Sauce Laddles Type: Spouted Bowl Body Shape: Circular With Pouring Spout Material: Stainless Steel, Highly Polished Appearance Over-all Length: 220 -230 Mm Ladle Bowl Length: 60 -65 Mm Long Ladle Bowl Diameter: 65 -70 Mm Depth: 10 -15 Mm Handle Details: 150-155 Mm Long X 20 -30 Mm Wide X 2 - 4 Mm Thick Color: Silver With Hang Hole For Hanging And Easy Access Dishwasher Safe Packed In Plastic Pouch The Item Must Have Good Quality 50 Pcs Server, Cake 1. Material : Stainless Steel Blade , Highly Polished Appearance 2. Over-all Length : 220 To 270 Mm 3. Width : 60 - 80 Mm 4. Thickness : 1.5 Mm To 2 Mm 5. Handle : 120 -140 Mm Long, Non-toxic Plastic 6. Shape : Shovel-shaped 7. Color : Silver 8. The Item Must Have Good Quality 9. Packed In Carton Box 50 Pcs Service Forks Type : Service Fork Body Shape: Fork Shape Material/appearance: Stainless Steel, Highly Polished, W/ Palin Design Over-all Length: 220 Mm - 260 Mm Width: 20 - 25 Mm Handle Thickness: 1.5 Mm - 4 Mm Handle Length - 165 Mm - 185 Mm 4 Tines Color: Silver Packed In Plastic Pouch 25 Pcs Service Tray Type: Plastic Body Shape: Rectangular Material: Plastic (pp) Size : 14 Inches X 18 Inches X 1 Inch (minimum) Color : Any Packed In Plastic Pouch The Item Must Have Good Quality 25 Set Show/service/base Plates 11" To 14" Type: Plain Type Body Shape: Round Material: Porcelain With No Design Supply Must Be A Set Consisting (1) Of Each: - 11 Inches, - 12 Inches, - 13 Inches, And - 14 Inches Plates Color: White Diameter, Inner : 225 Mm - 250 Mm Thickness: 3 Mm - 6 Mm Smooth And Glossy Surfaces 50 Pcs Side Plates Or Bread Plates 6'' Type: Plain Type Body Shape: Round Material: Porcelain With No Design Color: White Inner Diameter: 95 Mm To 120 Mm Outer Diameter: 145 Mm To 170 Mm Thickness : 3 Mm - 6mm Smooth And Glossy Surfaces Packed In Carton Box The Item Must Have Good Quality 50 Pcs Side Towels Type: Chef's Towel Body Shape: Rectangular Material: Oxford Polyester Soft Cloth Over-all Length : 640 - 680 Mm Over-all Width : 420 -460 Mm Color : Plain White Packed In Plastic Pouch The Item Must Have Good Quality 25 Pcs Silver Platter Type: Steel Type Body Shape: Round Material: Stainless Steel Diameter: 300 -330 Mm Thickness: 1 - 2 Mm Packed In Plastic Pouch The Item Must Have Good Quality 50 Pc Soup Bowl Type: Plain With Two Handles Body Shape: Circular Material : Porcelain Capacity : 24 Oz. (minimum) Packed In Carton Box The Item Must Have Good Quality Packed In A Carton Box 25 Pc Soup Laddle Type: Steel Type Body Shape: Circular Material: Stainless Steel, Highly Polished Appearance Over-all Length : 220 -235 Mm Ladle Bowl Details : 60 -65 Mm Long, 60 -75 Mm Diameter, 10 -15 Mm Deep Handle Details : 145 - 155 Mm Long X 12 - 25 Mm Wide X 1.5 -3 Mm Thick Color : Silver With Hang Hole For Hanging And Easy Access 15 Pc Soup Tureen Type: Steel Body Shape: Round Material: Stainless Steel Capacity: 7 - 11 Quart Size : 60 X 35 X 32 Cm (minimum) Packed In Plastic Pouch The Item Must Have Good Quality 100 Pc Spoon, Dinner Type : Dessert Spoon Body Shape: Oval Material/appearance: Stainless Steel, Highly Polished With Plain Design Over-all Length : 175 To 190 Mm Thickness : 2 Mm - 3 Mm Shorter Handle : 120 -130 Mm Color : Silver Packed In Plastic Pouch The Item Must Have Good Quality 100 Pc Spoon, Dessert Type : Dessert Spoon Body Shape: Oval Material/appearance: Stainless Steel, Highly Polished With Plain Design Over-all Length : 175 To 190 Mm Thickness : 2 Mm - 3 Mm Shorter Handle : 120 -130 Mm Color : Silver Packed In Plastic Pouch The Item Must Have Good Quality 100 Pc Spoons, Service Type : Service Spoon Body Shape: Oval Material: Stainless Steel, Highly Polished, W/ Plain Design Over-all Length: 220 Mm - 250 Mm Width: 30 - 38 Mm Handle Thickness: 1.5 Mm - 4 Mm Handle Length - 165 Mm - 185 Mm Color: Silver Packed In Plastic Pouch The Item Must Have Good Quality 100 Pc Spoons, Soup (cream And Cosume) Type: Soup Spoon Body Shape: Round Material/appearance : Stainless Steel, Highly Polished, W/ Plain Design, Rounded Tip Handle Over-all Length : 165 Mm - 200 Mm Smaller Oval Shaped Spoon Bowl And Tapers Slightly To The Tip Shorter Handle : 110 Mm - 170 Mm Thickness : 1.5 Mm - 3 Mm Color : Silver Packed In Plastic Pouch 50 Pc Steak Knife Type: Steak Knife Body Shape: Flat With Serrated Edge Material: Stainless Steel Steel Blade With Wooden Handle Length: 170 Mm To 203 Mm Handle Wood Thickness: 10 - 14 Mm With Serrated Blade Packed In Carton Box The Item Must Have Good Quality 25 Pc Sugar Container Type: Glass Type Body Shape: Round Material: Glass With Brass Lid (or Equivalent) Diameter: 70 -80 Mm Height: 130 -140 Mm Capacity: 12 Oz. Packed In Carton Box The Item Must Have Good Quality 50 Pc Table Cloth, 54 X 54 Inches Type: Plain Cloth Body Shape: Square Material: Oxford Polyester Cloth Color: Plain White Dimension: L 54 Inches X W 54 Inches (minimum) Packed In Plastic Pouch The Item Must Have Good Quality 100 Pc Table Cloth, Rectangular Type: Plain Cloth Body Shape: Rectangle Material : Linen Size : 120cm X160cm (minimum) Color : Any Color But Not Black Feature: Washable Packed In A Plastic Pouch 100 Pc Table Napkins, Cloth, 16"x16" Type: Plain Cloth Body Shape: Square Material: Oxford Polyester Cloth Or Its Equivalent Size: L 16 Inches X W 16 Inches (minimum) Color: Plain White Packed In Plastic Pouch The Item Must Have Good Quality 80 Pcs Table Skirting Cloth 90" To 90" Type: Plain Cloth Body Shape: Square Material: American Cotton Twill Cloth Color: Any Color Except Black Dimension: 90 Inches X 90 Inches (minimum) Packed In Plastic Pouch The Item Must Have Good Quality 50 Pcs Table, Square/rectangular (4's Or 6's) Type: Foldable Plastic Body Shape: Square/rectangle Material: High Density Polyethylene Table Top Powder Coated Steel Frame Dimension: 37 - 39 X 37 - 39 Inches Color: White Good For 4 Persons Packed In Carton Box The Item Must Have Good Quality 20 Pcs Tea Pot, 2 Pints Type: Porcelain Type Body Shape: Round With Handle And Pouring Spout Material : Porcelain Capacity : (2 Pint) Color : White Packed In Carton Box The Item Must Be Of Good Quality 50 Pcs Teaspoon Type : Tea Spoon Body Shape: Oval Tip Material/appearance: Stainless Steel, Highly Polished, W/ Plain Design Over-all Length: 120 Mm To 140 Mm Handle Thickness: 2 Mm To 4 Mm Short Handle Length - 100 Mm (minimum) Color: Silver Packed In Plastic Pouch The Item Must Have Good Quality 15 Pcs Tong, 8 Inches Type: Tong, 8 Inches Body Shape: Standard Material: Stainless Steel Size: 8 Inches Stainless-steel Arms With Soft, Comfortable Grips Nylon Heads Safe For Nonstick Cookware Heat-resistant Up To 400 Degrees Fahrenheit Tongs Lock Closed For Storage Preferably With A Packing Case Food Grade And Dishwasher-safe Must Be Branded 30 Pcs Tooth Pick Holder Type: Steel Type Body Shape: Round Material: Stainless Steel, Highly Polished In Appearance Diameter: 30 -35 Mm Diameter (minimum) Height: 65 -75 Mm Capacity: 1.24 Oz. (minimum) Packed In Plastic Pouch The Item Must Have Good Quality 20 Pcs Tray Stand Type: Foldable Body Shape: Rectangular Material: Chrome Plated Metal Folding Tray Stand Length: 470 -490 Mm Width: 400 -440 Mm Height: 770 -790 Mm Packed In Plastic Pouch The Item Must Have Good Quality 30 Pcs Tray, Bill Folders/change 1. Material : Heavy Duty Plastic ( Abs ) Or Its Equivalent 2. Height : 190 - 220 Mm 3. Width : 120 -140 Mm 4. Thickness : 2 Mm To 3 Mm (minimum) 5. Color : Black 6. With Check And Pen Holder 7. The Item Must Have Good Quality 8. Packed In Plastic Pouch 20 Pcs Tray, Round (bar) Type: Plastic Body Shape: Round Material: ( Pe/abs) Plastic Rubberized Surface, Non-slip/grip Tight Over-all Diameter: 345 -360 Mm (minimum) Thickness: 2 - 4 Mm (minimum) Color: Black Packed In Plastic Pouch The Item Must Have Good Quality 50 Pcs Water Goblet Type: Water Goblet Body Shape: Balloon-shaped Bowl Material: Crystal Clear Glass Over-all Length: 200 -220 Mm Capacity: 270 Ml To 300 Ml Rim Diameter - 55 -65 Mm Thickness: 1 Mm To 3 Mm Stem Length : 75 -85 Mm Stem Diameter : 6 -8 Mm Base Thickness : 3 -4 Mm Base Diameter : 7 -80 Mm Packed In Carton Box The Item Must Have Good Quality 30 Pcs Water Pitcher (stainless) Type: Steel Type Body Shape: Circular Material: Stainless Steel, Highly Polished Appearance Height: 170 Mm To 220 Mm Top Diameter: 110 -120 Mm (approximate) Capacity: 1 - 1.5 Liter With Pour Spout Dishwasher Safe Packed In Plastic Pouch The Item Must Have Good Quality Lot 8. Tangub City National High School (front Office Services And Local Guiding Services) Php 232,832.00 50 Pcs Calculator Type: Simple Calculator, Non Scientific Body Material: Hard Plastic Minimum Size: 110mm Width X 140mm Long Lcd Display: At Least Font Size Is 8mm X 5mm With Dual Power; Solar Cell And Battery With At Least 8 Digits Display Includes Spare Battery Packed With Protective Carton Box User's Manual In English Which Includes: A. Parts Manual With Labels, B. Assembly Instructions C. Operating Procedures On How To Use The Equipment, 1 Pcs Cart, Bell Boy Type:hotel Luggage Trolley Capacity: At Least 450 Kilograms Minimum Dimensions: Length - 1000mm X Width - 600mm X Height - 1700mm Frame Material: Stainless Steel Tubing Stainless Tube Diameter: At Least 35mm Black Powder Coated Steel Platform With Carpeted Surface And Rubber Bumper At The Edge With 4 Pieces X 200mm Diameter Black Pneumatic Swivel Wheels Packed With Shipping Carton Box Branded 1 Pcs Cash Register With Drawer Printer: Width: 57mm (minimum) Speed: 2 Lines/sec (minimum) Lcd Display Size: 5cm Width X 10cm Long(minimum) With Drawer At Least 4 Bills And 5 Coins Compartments With Drawer Dimension At Least 410mm Width X 450mm Depth Input Method: Numeric 10-key Interface With At Least 2 Ports Power Source: 220-240volts Ac, 50/60hz; With Ac/dc Adapter Can Be Operated With Battery Programmable User's Manual In English Which Includes: A. Parts Manual With Labels, 1 Pcs Credit Card Imprinter Height Of The Imprinter 2 1/2 Inch (minimum) X Width 5 1/2 Inch (minimum) X Length 11 Inches (minimum) Carriage Material: Steel Body:plastic Color: Black 20 Characters Per Line Card Mounting Can Accepts At Least 0.030" Thick Size Credit Cards Plate Can Accommodate Up To 5 Lines, Manual Type With User's Manual In English Which Includes: A. Parts Manual With Labels, B. Assembly Instructions, C. Operating Procedures 30 Pc Credit Card Voucher Holder Material: 3 Mm Thick Clear, Acrylic, Dimensions: Height: At Least 255 Mm, Width: At Least 210 Mm, Thickness: At Least 70 Mm 1 Pcs Detector, Fake Bills Led Display; Led Display Size: At Least 5 Cm Width X 10 Cm Long; Hard Plastic Casing; Ultraviolet (uv) And Magnetic (mg) Sensors; Power Source: Built In Rechargeable Battery,12v Output And Ac 100- 240v Adapter; With Complete Detection; Accessories Includes: Tough Plastic Carrying Case, Power Cord, Cleaning Brush, And Power Charger; User's Manual In English Which Includes: A. Parts Manual With Labels, B. Assembly Instructions, 3 Pcs Guest Folio Rack Material: Hard Plastic; Accommodates At Least 50 Room Divider Indexes; With Divider Boards With Metal Tabs; A4 Size Divider; With Metal Sidings 1 Pc Hypercom Memory: 1 Mb Ram (minimum) Lcd Display; 160 X 80 Pixel Graphics (minimum) With Card Reader Magnetic Stripe Pin Pad Port: 4-wire, Rs485; With Peripheral Ports For Pc Connection; Electronic Cash Register Or Journal Printer; With At Least 2400bps Modem; Support Synchronous (sdlc) And Asynchronous, Lan Operation; With Pin Encryption; With Thermal Printer At Least 576 Dots Per Line; Thermal Paper – 2 Inches Wide X 3 Inches Roll Diameter (min.); Keypad: Membrane, 12 Keys, Water-resistant; 1 Pc Key Card Maker With Verifier Set Of Hotel Door Lock System With Management Software; A) 1 Unit - Card Type Door Lock With Inductive Distance At Least 4cm B) 1 Unit - Card Encoder Unit With 25 Pieces Door Room Key Cards Computer Software System For Door Lock And Making Cards With Complete Accessories Including The Usb Type A Cable Interface To The Computer User's Manual In English Which Includes: A. Parts Manual With Labels, B. Assembly Instructions C. Operating Procedures On How To Use The Equipment 1 Pcs Key Rack Rack Material: Wood Number Of Racks: Can Accommodate At Least 40 Key Cards Minimum Rack Size: 70mm Width X 110mm Height Depth Of The Rack At Least 50mm Any Color Paint Type:wall Mounted Rack Pack With Shipping Carton Box 1 Pc Safety Deposit Box Vault Material: Metal, Powder Coated, Solid Steel Door Thickness: 4mm(minimum) Body Thickness: 2mm(minimum) Minimum Outer Dimension: L: 30cm X H: 20cm X W: 20cm Electronic Lock System Battery Operated Digital Panel: Requires 4 X ‘aa’ Batteries User's Manual In English Which Includes: A. Parts Manual With Labels, B. Assembly Instructions, C. Operating Procedures On How To Use The Equipment, Branded 20 Pcs Speaker, Lapel Frequency At Least 500mhz With Audio Input Connector With Operation Range At Least 50meters Receiver/70ma Earphone Output Level: 32ohm, 65mw Operates With Energizer Battery With Minimum Powerconsumption Of Transmitter At Least 3v/70ma Receiver: 3v/70ma 25 Sets First Aid Kit Type: Emergency Case; Contents: First Aid Quick Reference Guide, 1pc; Sterize Gauge Swab(4 X4 X12 Ply) 100 Pcs/pack, 1 Pack; Adhesive Strips/band -aid, 50 Pcs/pack, 2 Packs; Gloves, Disposable, Medium Size, 2 Pairs; Hypo Allergenic Adhesive Tape, 5cm X 5cm, 2 Rolls; Triangular Bandage/arm Sling, Min 90cm X 90cmx 120cm, 2pcs; Safety Pins, 1 1/4 Inches, (12 Pcs), 1 3/4 Inches (12 Pcs); Stainless Steel Bandage Scissors, 2pcs; Betadine, 60ml, 2 -3 Years Expiration, 2 Bottles; Dust Mask, 2pcs; Hand Towels Or Face Towels, White Color, 6 Pcs; Gauze Bandage, Minimum 5cm X 4cm, 2 Rolls; Antiseptic Handwash/germicidal Soap, 60 Gms , 2pcs; Torniquet, 2 Pcs; Spirit Of Ammonia, 30ml, 2-3 Years Expiration, 1 Bottle; Burn Cream Ointment, 20g To 30g, 2- 3years Expiration, 1 Tube; Medical Tweezers Min. 8cm, Plastic, 2pcs; Plastic Bags, Resealable, Minimum Of 24pcs, 100mm X 180mm, 24pcs, 150mm X 230mm Cotton Balls , 50 Balls In A Sealed Package, 2 Packs Hot And Cold Pack, Reuseable, 1 Pack Water Resistant And Sturdy Case W/ Handle That Can Accommodate All The Listed Items. 4 Pcs Megaphone Battery Operated (4 Pcs - Size D Battery) With Built-in Siren Power Output: 20-watts (minimum) Range: 700 Meters (minimum) With Hand Grip And Carrying Strap Branded With Users Manual That Contains The Specification, List Of Parts, Instruction Guide, Troubleshooting, Safety Instruction. 100 Pcs Whistle Anodized Aluminum;size : Length - 6.5cm X 3cm Diameter; Handy And Lightweight; Loud Whistle Can Be Heard For Far Distance Of 100 Meters; With Key Ring For Attachment 2 Pcs White Board, Floor Standing, Rolling Board: White Formica Laminated, Plane Will Not Deform.board Size: Rectangular 1800mm W X 1000 To 1200mm H, Board Edges Secured With Aluminum Clip Edging 17 Mm (minimum) Wih Plastic Corner Capscomes With Metal Tray For Marker And Eraserthe Stand And Frame Are Constructed With Aluminum Or Powder Coated Steel 25mm Square Tube (minimum), Sturdy, No Wobblewith 4 Lockable Hard Plastic Caster Wheelsoverall Height From Floor: 210 To 214cmsmooth Surface, No Sharp Edges Total Abc 3,978,106.00 2. The Department Of Education – Division Of Tangub City Now Invites Bids For The Above Procurement Project. Second Procurement Of Learning Tools And Equipment For Technical Vocational Livelihood To Deped-public Schools. Bidders Should Have Completed A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii (instructions To Bidders). 3. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) No. 9184. 4. Interested Bidders May Obtain Further Information From Department Of Education – Division Of Tangub City And Inspect The Bidding Documents At The Address Given Below From 8:00 A.m. To 5:00 P.m. , Mondays To Fridays Except Holidays. 5. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders On January 8, 2025 From Given Address And Website/s Below And Upon Payment Of The Applicable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb, In The Amount Of: Lot 1 - Five Hundred Pesos (p500.00) Lot 2 - Five Hundred Pesos (p500.00) Lot 3 - Five Hundred Pesos (p500.00) Lot 4 – One Thousand Pesos (p1,000.00) Lot 5 - Five Thousand Pesos (p5,000.00) Lot 6 - Five Hundred Pesos (p500.00) Lot 7 – One Thousand Pesos (p1,000.00) Lot 8 - Five Hundred Pesos (p500.00) The Procuring Entity Shall Allow The Bidder To Present Its Proof Of Payment For The Fees To Be Presented In Person. 6. The Department Of Education – Division Of Tangub City Will Hold A Pre-bid Conference On January 20, 2025, 9:00 Am At Division Office Conference Hall Which Shall Be Open To Prospective Bidders. 7. Bids Must Be Duly Received By The Bac Secretariat Through Manual Submission At The Office Address As Indicated Below On Or Before 9:00 A.m. On February 4, 2025. Late Bids Shall Not Be Accepted. 8. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 16. 9. Bid Opening Shall February 4, 2025, 9:00 A.m. At The Given Address Below. Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend The Activity. 10. Bidders Or Its Authorized Representatives Are Encouraged To Attend The Pre-bid Conference To Ensure That They Fully Understand The Procuring Entity’s Requirements. 11. The Department Of Education – Division Of Tangub City Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Implementing Rules And Regulations (irr) Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 12. For Further Information, Please Refer To: Gina L. Mandawe Head, Bac Secretariat Deped, Division Of Tangub City, Anecito Siete St., Mantic, Tangub City 7214 (088) 530-5988 Depedtangub.bacsec@deped.gov.ph Https://tangub.deped.gov.ph/ 13. You May Visit The Following Websites: For Downloading Of Bidding Documents: Https://tangub.deped.gov.ph/ Erlinda G. Dael, Phd., Cese Assistant Schools Division Superintendent Bac Chair

Details: Description Invitation To Bid Project No: 005 – 2025 1. The Department Of Education Through The Fy 2024 Gaa Intends To Apply The Sum Of Seven Million Three Hundred Thirty-eight Thousand Five Hundred Seven And 00/100 (7,338,507.00) Being The Approved Budget For The Contract (abc) Described Below For The Procurement Of Assistive Devices, Equipment, Supplies And Materials For Inclusive Learning Resource Centers. Bids Received In Excess Of Abc Shall Be Automatically Rejected At The Bid Opening. Unit Description Qty Cost Abc (vat Inclusive) 1 Lot Procurement Of Assistive Devices, Equipment, Supplies And Materials For Inclusive Learning Resource Centers 1 1 Unit Learners'/clients' Chart Materials A4 Size 8-1/4 X 11-3/4 Inches Or 210 X 297 Mm Or 29.7 X 21 Cm Laminated Full Color High Quality Print Photopaper 10 70.00 700.00 2 Set Anatomical Model-human Torso Model Size: 1/2 Life Size Material: Pvc, Includes: Stand 1 62,918.00 62,918.00 3 Unit Blood Pressure-blood Pressure Monitor Type: Upper-arm Monitor Type: Digital Cuff Size: 32cm Dimension (w X H X D): 145 X 466 X 145mm Weight: 250g Power Supply: Battery Type: Li-polymer Smart App Availability: Yes, Automatic Shut Off: Wi-fi: No 5 6,560.00 32,800.00 4 Unit Stethoscope: Dual Tube Stethoscope Weight: 185g, Length: 80cm Product Material: Polymer Diaphragm, Listener Material: High-density Stainless Steel Product Composition: Eartip, Ear Hooks, Leaf Spring, Hose Heads, Diaphragms 2 1,380.00 2,760.00 5 Piece Tape Measure-material: Pvc It Has Centimeter Scale On Reverse Side Which Is Up To 300cm Large, Easy To Read Marking Measures Up To 120 Inches 10 300.00 3,000.00 6 Piece Hand Dynamometer - Hand Dynamometer Type: Electronic Counting Gripper Function: Comprehensive Fitness Exercise Material: Abs Size: 15cm/5.90""x10.5cm/4.13""x2cm/0.79"" 10 1,900.00 19,000.00 7 Packs Ice Massage Caps- Size: 2 Count (pack Of 1) Measuring 2.9” In Diameter, The Ice Cup Massager Holder Also Fits Comfortably In The Hand. Material: Polyethylene 10 700.00 7,000.00 8 Unit Balance Board- Balance Board Type: Rocker Board Dimensions: 32.28 X 11.81 X 0.59 Inches Weight Capacity: 100 Kg Material: Beech Wood Anti-skid Feature: Not Specified 5 3,700.00 18,500.00 9 Unit Treatment Table- Top Shelf With Guard Rail And Formica Material. Down Shelf, Material Plain Sheet. Mounted On 4 Swivel Caster Rubber Wheels 2″ With 2 Pieces Lock. Size: Lxwxh (28″x20″x34.5″) Painted White 1 17,400.00 17,400.00 10 Unit Exercise Steps-aerobic Step Board 69 X 28 X 15cm. Dimension: 69 X 28 X 15cm Length: 27" Width: 10.5" Adjustable Height Up To 10cm To 15cm. Offers A Secure, Nonslip Surface For Your Workout Routine, Nonskid, Feet Provide Stability & Protect Floors. 5 1,934.00 9,670.00 11 Pair Pediatric Examination Gowns- Assorted For Kids And Adult Pediatric Examination Gowns Opening: Full Open Back. Style: Child Size Color: Jellybean Print. Made With High Quality, 100% Cotton Comfortable, Durable, Washable, And Reusable Hook And Loop Closures At Neck And Mid-back. 10 700.00 7,000.00 12 Piece Towels- Material: High Quality 100% Cotton Terry. 500gm2. Size: 90 X 180cm. 20 300.00 6,000.00 13 Piece Bed Sheets- Material: Cotton + Polyester, Packaging Content: 2 Pcs Pillowcase, 1 Pc Fitted Sheet, Single Size:36"*75"+7.8", Pillowcase Size: 18'*28", Garterized Corners 20 2,000.00 40,000.00 14 Piece Pillows- Pillows, Plain White, Soft Pillow, Size:18x28 Inches 10 900.00 9,000.00 15 Piece Pillowcase- Length: 50 Cm (20 ") Pillowcase Quantity: 1 Piece Width: 80 Cm (31 ") 100 % Polyester 20 180.00 3,600.00 16 Piece Blankets- Length: 160 Cm White Sheet Soft Texture, High Quality Fabric Size: 52 X 90 Inch 20 450.00 9,000.00 17 Unit Step Stools - Step Stools Double Steel Caravan Step. Rubber Non- Slip Steps. Leg Distance Front To Back 65 Cm. Width 42 Cm. Top Step Height 38 Cm. Bottom Step 20 Cm. 5 3,600.00 18,000.00 18 Unit Therapist Stools On Wheels-adjustable Height Of 19 - 24". It Comes With A 3" Hi-density Cushion With Multi-layered Padding, And A 14" Seat Diameter. Built With 5 Casters Made Of Plastic Easy To Clean. Color: Black 5 4,950.00 24,750.00 19 Piece Kinesiology Tape-ultra-strong And Sticky-hypoallergenic Adhesive Water Resistant. 97% Cotton, 3% Nylon. 180% Stretch For Full Range Of Motion Latex And Zinc Free Sticks 2-7 Days 5-10 Applications Per Roll Each Is 2""x 16.4"" (5cmx5cm) 20 2,100.00 42,000.00 20 Set Splinting Materials - Rescue Padded Board Splint. 6 Paddes Wood Splint (different Sizes) Sizes: 35"", 25"" And 15". Velcro Straps Color: Blue. 20 4,200.00 84,000.00 21 Unit Paraffin Bath- Large Opening Design: Inner Pot Allows For Hands, Feet, And Elbows To Be Dipped Into The Melted Wax. Alloy Heating Pot Melts Paraffin Wax Blocks In 0.5 Hours. Adjustable Heating Ranges From 86-158°f. Timer: Settable From 1 To 99 Minutes. (free Installation) 2 32,340.00 64,680.00 22 Set Dumbbells Sets- Weight: 37kg Type: Medical Rehabilitation Equipment Total 18 Dumbbells 1 Lb / Piece, 2 Pieces 2 Lbs / Piece, 4 Pieces 3 Lbs / Piece, 4 Pieces 4 Lbs / Piece, 4 Pieces 5 Lbs / Piece, 4 Pieces 3 25,000.00 75,000.00 23 Set Goniometers- Protractor Goniometer With 360 Degrees Coverage To Measure Joint And Compare The Changes In Joint Angles Material: Clear Plastic 3 Goniometer: 12-inch, 8 Inch And 6 Inch 3 600.00 1,800.00 24 Set Reflex Hammer-features: Pointed Babinski-style Tip Zinc Alloy Comfortable Handle Grip Control, Hammer For High Elastic Pvc Rubber Material: Zinc Alloy + Pvc; Color: Black Package Size: 27*11*3.5cm/10.6*4.3*1.3-inch Package Weight: 140g/4.9oz. 1 8,100.00 8,100.00 25 Piece Thermometer - Body Temperature Measurement: 34.0-42.9°c / 93.2-109.2°f. Material: Abs Plastic. Accuracy: (+/-)0.2°c. Auto-shutdown Time: About 18s Power Supply: 2 * 1.5v Aaa Batteries (not Included). 1 Year Warranty 5 1,600.00 8,000.00 26 Unit Multiple Mode Electrical Stimulator-1 Second Measuring Time. 3 Color Backlight Fever Reminders Auto Shut Off At 18 Seconds Store 50 Sets Of Data. Body Temperature Measurement: 34.0-42.9°c / 93.2-109.2°f. 3 9,884.00 29,652.00 27 Piece Foam Rolls- Material: Expanded Polypropylene Foam Item Weight: 0.42 Pounds Size: 18 Inches 3 4,000.00 12,000.00 28 Piece Mobilization Belts And Devices- Size 8 Feet Specific Uses For Product. Use For Legs, Hips, Arms, Back, Whole Body - High-quality Nylon Mobilization Belt Features A Plastic Side-release Buckle And Is Designed For Durability And Patient Safety. 5 2,850.00 14,250.00 29 Piece Gait Belt-1x Transfer Gait Belt Measurement Length: 60 Inches Width: 2 Inches 5 1,458.00 7,290.00 30 Set Theraband -4 Resistance Levels, Including Yellow, Red, Green, And Blue Supplied In Lay Flat Length Of 8", 12" And 18" Latex Rubber Weight Level: Yellow: 3 Lbs-4.3 Lbs Red: 3.7 Lbs-5.5 Lbs Green: 4.6 Lbs-6.7 Lbs Blue: 5.8 Lbs-8.6 Lbs 5 10,100.00 50,500.00 31 Piece Wedge Bolsters- A Firm And Breathable Bed Wedge Pillow Stays Cool, And Its Measurements Are 25″l X 25″w X 12″h Inches. / Breathable & Washable Cover / Designed To Provide Higher Body Support. 5 6,998.00 34,990.00 32 Piece Round Bolsters-weight：0-0.5 Kg Shape：column Feature：memory Filling：microfiber Material：100% Fiber Size:8" X 36" Color：white - Ideal For Hugging, Cylindrical Pillow, Great For Side Sleepers. 5 4,800.00 24,000.00 33 Piece Core Peak Bolsters- An All-purpose Positioning Aid • Provides Support Under The Legs, Arms, Feet, And Other Areas Of The Body. Fits Standard Treatment Tables • 18" In Length With At Least 6" In Diameter. 5 9,006.00 45,030.00 34 Piece Round Bolsters-weight：0-0.5 Kg Shape：column Feature：memory Filling：microfiber Material：100% Fiber Size:8" X 36" Color：white - Ideal For Hugging, Cylindrical Pillow, Great For Side Sleepers. 5 1,500.00 7,500.00 35 Piece Core Peak Bolsters- An All-purpose Positioning Aid • Provides Support Under The Legs, Arms, Feet, And Other Areas Of The Body. Fits Standard Treatment Tables • 18" In Length With At Least 6" In Diameter. 4 1,100.00 4,400.00 36 Piece Walking Cane-adjustable Aluminum Cane With Wooden Handle, Anodized Finish And Rubber Tip. The Tube Has A Spring Lock Pin For Adjusting Handle Height From 58-94 Cm. 5 1,320.00 6,600.00 37 Piece Quad Cane -stable Structure, Thickened Stainless Steel Material. Abs Non-slip Handle, Ergonomic Design, Comfortable Grip. Spring Button For Easy Height Adjustment. Firm Lock Hoops To Stabilize The Body. 4 2,740.00 10,960.00 38 Piece Wheelchair - Front Wheel Size: 6 Inches Expanded Size: 82 * 58 * 87cmseat Depth: 38cmrear Wheel Size: 16 Inches Back Height: 42cmfolded Size: 70 * 25 * 72cmhandrail Spacing: 55cmseat Width: 45cmnet Weight: 11kgnet Weight Of All Aluminum Alloy Frame: 11kg 10 5,600.00 56,000.00 39 Piece Pediatric Walker- Height-adjustable Frame Sizes. 360-degree Swivel Front Casters For Versatile And Flexible Mobility. Foot-operating Locking Mechanism On Front Casters. Rubber Tire Design 5 13,200.00 66,000.00 40 Set Communication Boards. Measures 9"x7.5". Binder Comes With 5 Different Colorful 10 Mil Poly Dividers, 3 Hard Strips (hook) Attached On Each Side To Hold 30 Cards. Each Card Measures 1.5 X 1.5. Inch Mounted With 1/2-inch Soft Dot (loop), And Round Corner Cut. 10 6,172.00 61,720.00 41 Set Dry Erase Sleeves. Reusable Dry Erase Pockets. Colors: Blue, Pink, Yellow, Red, Green, Purple. Size: 25.5*35.5cm(1pcs). Quantity: 12pcs Package Including: 6 X Dry Erase Pockets 6 Pens 10 796.00 7,960.00 42 Set Wind Up Toys. Category: Clockwork Engineering Road Roller Material: Plastic Size: 9.9*6.5*5.3(cm) Color: Three-color Random Hair Ages: 3+ 10 440.00 4,400.00 43 Set Wordless Picture Books. A Wordless Book About Dealing With Big Emotions Like Fear, Grief, Loss, Sadness, And Anger Hardcover | 36 Pages Product Dimension: Approx. W1cm X L22.2cm X H22.2cm Product Weight: Approx. .28kg 10 1,998.00 19,980.00 44 Piece File Folders. (black Or White) Model: Minimum Of 100 Pages Capacity Size: 310*235mm Suitable For School And Office Supply 10 280.00 2,800.00 45 Set Articulation Cards. Genre: Children's Learning & Education Sub-genre: Society & Culture Label: Scholastic Teaching Resources Language: English Publisher: Scholastic Teaching Resources 10 3,913.00 39,130.00 46 Set Basic Vocabulary Board. Each Unit Comes With: Flashcards Smash Mat Trace And Color Cut And Glue Flipbook Black And White Versions Of All Activities 10 10,150.00 101,500.00 47 Set Phonics Phones. Specifications - Each Pack Includes Two Durable Whisper Phones, One In Vibrant Blue And One In Eye-catching Red. 10 536.00 5,360.00 48 Piece Taekwondo Mats. Thickened 1 Meter X 1 Meter X 2 Cm Interlocking Mats. Color Blue. 30 1,750.00 52,500.00 49 Set Vestibular Balls- (3 Pieces) Material: Synthetic Material Size: 55.0 / 65.0 / 75.0 Cm. Weight: 1100.0 / 1400.0 / 1700.0 G. Color: Violet / Blue / Black 3 6,200.00 18,600.00 50 Unit Monkey Bar With Platform For Swing- Materials: 7/8-inch Plywood 3.5’x2, Washable Mat, 1/2-inch Braided Ropes, Stainless Steel Carabiners Dimensions: 47 X 27.5 Inches; Maximum Rope Length - 7 Feet, Weight Limit: 100 Kilos (free Installation) 1 42,000.00 42,000.00 51 Set Trampoline With Handrails 40-inch Jumping Surface Area, Handrail Adjusts From 28.5"" To 36.5""h 16lbs. Holds Up To 300 Lbs 2 11,580.00 23,160.00 52 Unit Tumble Barrels-inside Diameter: 18"-24”, Outside Diameter: 24", Weight: 250lbs. (free Installation) 1 40,695.00 40,695.00 53 Set Wall Bars- 6-hole Design Pull Up Bar. The Maximum Weight Is 200kg. Solid Steel Bar With Black Powder Coating To Prevent Rust And Corrosion And Prolong Service Life, With Soft Cushions. 2 2,598.00 5,196.00 54 Set Adl Board - 6 Colors, 6 Different Dressing Skills Training. A Quiet Skill Book Made Of Cardboard And Non- Woven Fabric. Suitable For Children 2-7 Years Old. Package Dimensions: 11.73 X 9.76 X 2.28 Inches Item Weight: 1.28 Pounds" 10 494.00 4,940.00 55 Unit Pediatric Walker - 360-degree Swivel Front Casters For Versatile And Flexible Mobility. Total Height: 75-90cm Side Wheel Width: 70cm. Front And Rear Track Width: 75cm. Left And Right Wheel Track: 40cm Suitable Height: 85-120cm. Weight: About 12kg 4 17,998.00 71,992.00 56 Set Assessment Tool Set Of Assessment Tools For Behavioral, Psychological, Intellectual, Motor, Socio- Emotional (1 Copies Per Set) Like: Ravens Progressive Matrices Tests, Goodenough-draw A Person Test 2 48,000.00 96,000.00 57 Set Assessment Tool Set Of Assessment Tools For Behavioral, Psychological, Intellectual, Motor, Socio- Emotional (1 Copies Per Set) Like: Wechsler Intelligence Scales For Children (wisc-v) 2 48,000.00 96,000.00 58 Pcs Reading Stand - High-grade Steel (iron). Color: Black. Dimensions: 26 Cm X 21 Cm X 16 Cm (folded) Adjustability: Multiple Notches For Adjustable Height And Angle. 1 Rotary Page Clip To Hold Pages Securely. 10 1,050.00 10,500.00 59 Unit Braille Translator- Supports Translation Of Print (word, Html, Daisy And Others) To Braille For Over 130 Languages. Drives All Major Braille Embossers. (with 6 Months Warranty) 1 136,800.00 136,800.00 60 Unit Laptop 15.5" – 17" Monitor, Processor: Between 2.0- 2.8ghz 512gb Ssd, 8gb Ram (3 Mos. Warranty) 36 39,000.00 1,404,000.00 61 Cord Hdmi Cord 5 Meters 5 600.00 3,000.00 62 Cord Hdmi Cord 10 Meters 5 900.00 4,500.00 63 Set Connector Cord. Cord With Male Plug To Connect From Cellphone/ Laptop To Sound Systems Microphone Port. 5 500.00 2,500.00 64 Unit Augmentative Communication Systems. Package Dimensions 9.13 X 3.03 X 1.1 Inches Batteries 2 Aaa Batteries Required. (included) Preprogrammed Commands Wide Variety- Travel Bag- Aac Device 10 3,702.00 37,020.00 65 Unit Call Lights. Receiver Working Voltage: 110-260v Transmitter Battery: 12v 23a Alkaline Battery Working Distance: 1000 Feet In Open Area. [packing List]. 3 Receivers 2 Transmitters. 2 X Double-sided Tape. 1 X User Manual. 2 X 12v 23a Batteries. 10 1,536.00 15,360.00 66 Unit External Hard Drive. 1tb External Hard Drive Usb 3.0 5 3,500.00 17,500.00 67 Unit Audio Voice Recorder. Built-in 375mah Battery, Specification: Recording Time: 512kbps， 32gb: About 144 Hours. Storage Media: Tf Card, 32gb, Battery Capacity: 375mah, Package Size: 15.2x7.8x3.7cm/5.9x3x1.4in, Package Weight: 135g – 140g/4.7oz 10 2,674.00 26,740.00 68 Unit Portable Reading Camera -macro Focus Range 10 Cm Shooting Modes Easy, Macro, Automatic Exposure Control Type Automatic Color; White Video Capture Resolution; 1080p, 2448p 5 10,260.00 51,300.00 69 Unit Laser Printer. Computer Printers Using Powder - Based For Swell Paper. 2 20,000.00 40,000.00 70 Unit 3 In Printer - Print, Scan, Copy, Fax With Adf, Flatbed Color Image Scanner, A4, Ltr, 8.5 X 13’, Folio 9 19,080.00 171,720.00 71 Unit Projector -5,000 Ansi Lumens (standard). Wxga 1,280 X 800) Dlp Type Projector. With Built-in Speaker X 16,000 Hours (standard), 10,000 Hours (eco), 15,000 Hours (extreme Eco) Lamp Life Wireless Projection Hdmi Cable, Bag 2 Years Warranty" 1 25,000.00 25,000.00 72 Unit Projection Screen. Specs: 120 Inch Projector Screen With Tripod Stand Home Outdoor Screens Cinema Portable 1 6,490.00 6,490.00 73 Pcs Calculator. Basic Calculator Big Calculator. Office Supplies. Dimension: 160.4x164.5x44.2mm. Color White. Dual Power Supply. Aaa Battery With Solar Panel. Inner Concave Buttons. 5 500.00 2,500.00 74 Unit Touch Screen Tv – Not Less Than 55" Android Tv (free Installation) 1-year Service Warranty 1 61,000.00 61,000.00 75 Pcs Cork Bulletin Board (20x30cm Cork Board With Black Wooden Frame) 1 430.00 430.00 76 Pcs Convertible Drawing And Drafting Table (manual Lift Dimension W-7.75 X D 24x H22" To 31.5") 3 8,400.00 25,200.00 77 Pcs Table. Desk Painting Easel (wooden Easel Stand For Painting 1.75m Complimentary Screws Firm And Strong) 5 454.00 2,270.00 78 Pcs Gauze Bandage (sterile Gauze Bandage 3x10 Per Box) 2 300.00 600.00 79 Pcs Povidine-iodine 120ml (antiseptic Wound Solution) 5 250.00 1,250.00 80 Pcs Artist Taboret (35 ½" H X 17 ½" W X 14 ½" D+9/cm X 44cm X 37 Cm 1 26,784.00 26,784.00 81 Pcs Medicine Cabinet Large. Dimension: 29 X16.5x16 Cm 2 1,500.00 3,000.00 82 Pcs Sewing Machine (zigzagger) Power：90w, Rated Voltage：220v, Number Of Stiches：23, Automatic Winding. Presser Foot Pressure Adjustable (free Installation) 1 25,000.00 25,000.00 83 Pcs Sewing Machine (electric) (portable Sewing Machine With 23 Stitches (free Installation) 2 15,000.00 30,000.00 84 Pcs Tailors’ Scissors (10") Heavy Duty 5 1,500.00 7,500.00 85 Pcs Glue Gun (20w High Temperature) 5 111.00 555.00 86 Pcs Acrylic Color (set 12 Pc X 12 Ml) 5 368.00 1,840.00 87 Pcs Scissors, 5" Blunted Scissors, Plastic Handle. 5 112.00 560.00 88 Pcs Cutters. Snap Off Blade Knife Blade, Refill 9 Mm 5 13.00 65.00 89 Pcs Watercolors (50 Color Solid Watercolors Tin Box (202'82'33mm) 5 441.00 2,205.00 90 Pcs Art Paper (assorted Colors, Short Size) 5 270.00 1,350.00 91 Pcs Paint Brushes (12 Pcs Fine Detail Paint Brush) 5 246.00 1,230.00 92 Pcs Yarn (yarn Hand Knitting And Crochet Single Color (5 Colors) 5 30.00 150.00 93 Pcs Glue (1 Bottle 240g) 5 126.00 630.00 94 Pcs Colored Pencils (colored Pencils 12/set) 5 190.00 950.00 95 Pcs Colored Pens (fine Line Colored Marker 24 Colors In Pvc Bag) 5 90.00 450.00 96 Pcs Sewing Pins (sewing Pins 40 Pcs/set0 5 10.00 50.00 97 Pcs Sewing Needles(hand) (sewing Needles Big And Small) 5 18.00 90.00 98 Pcs Rotary Cutter (45mm) 5 169.00 845.00 99 Pcs Tape Measure (body Tape Measuring Ruler Tailoring) 5 16.00 80.00 100 Pcs Crochet Hooks (100 Pcs Crochet Hook) 5 286.00 1,430.00 101 Pcs Knitting Needles (2 Pcs/set (35cm) Knitting Sweater Stick Needle Bamboo Sweater Needle Knitting Scarf Tool) 5 144.00 720.00 102 Pcs Crochet Thread (thread Yarn 175 M) 5 46.00 230.00 103 Pcs Sewing Thread (polyester 1000 M) 5 42.00 210.00 104 Pcs Painting Easel. Studio/ (90/150 Cm Easel Wooden Standard Painting Display) 5 569.00 2,845.00 105 Pcs Manual Pencil Sharpener (one -hole Sharpener Tub) 5 68.00 340.00 106 Pcs Doll Mannequin. Whole Body With Stand Decor Body Dress Full Body Display 5 411.00 2,055.00 107 Pcs Transparent Edge T- Square (hand Tool Inch Metric Ruler 6") 5 535.00 2,675.00 108 Pcs Wood Carving Set. Carpentry Tools (professional 12/set Manual Wood Carving) 5 1,670.00 8,350.00 109 Pcs Staple Gun. (gun Tacker/ Staple Gun Length-18cm Width -12cm H-3cm, Color- Silver Head T50) 5 226.00 1,130.00 110 Pcs Slope Sink. (single Bowl Stainless Steel Kitchen Sink Box 15" Single Bowl Kitchen Sink Sus 304) 5 21,892.00 109,460.00 111 Pcs Roofing Square. Dual Marking Right Angle Picture Framing Carpenter Ruler (wadlow Stainless Steel Angle Ruler Aluminum Alloy Body Heavy Duty Tool) 5 216.00 1,080.00 112 Pcs Professional Compound Mitre Box & Saw (mitre Box And Box Saw Set 12 Inch) Miter Box Will Handle Stock 7 1/4" High, 8" Wide At 90°, And 5" Wide At 45°. The Saw Can Be Set At Any Angle And Has Automatic Stops For 90°, 45°, And For 5, 6, 8 And 12-sided Frames. 1 1,510.00 1,510.00 113 Pcs Drawing Lamp (metal Adjustable Arm Work Desk Lamp) 5 373.00 1,865.00 114 Pcs Chisel Rack For Wood Carving (professional 12-piece Wood Carving Chisel Set With Black Case Sharp Hand Tools For Beginners) 5 1,299.00 6,495.00 115 Pcs Corner Clamp (90-degree Single Swing Jaw Corer Clamp 68 Mm) 5 258.00 1,290.00 116 Pcs Decorative Realistic Artificial Fruits (realistic Artificial Fruit Such As Apples, Orange, Lemon, Pineapple And Banana) 5 293.00 1,465.00 117 Pcs Geometric Shapes Set (wooden Montessori Learning Geometric Building Blocks) 5 1,176.00 5,880.00 118 Pcs Geometric Designer Templates (multi -functional Geometric Ruler) 5 118.00 590.00 119 Pcs Stack Rack (toy Origami Rack Shelves) 5 1,477.00 7,385.00 120 Pcs Picture Frame And Miter Clamp (90 Degree Right Angle Clip Picture Frame) 5 710.00 3,550.00 121 Pcs Heat Gun (heat Gun With Accessories 2000 W) 5 1,725.00 8,625.00 122 Pcs Tape Dispenser (tape Dispenser 1") 5 114.00 570.00 123 Pcs Multi- Function Three - Hole Puncher (multi-dimensional 3 -hole Puncher) 5 4,176.00 20,880.00 124 Pcs Metric Scale (technical Triangular Scale. Set Of 45, 90 Degrees) 5 68.00 340.00 125 Pcs Steel Tape Measure (tape Measure 8m/20) 5 470.00 2,350.00 126 Pcs Heavy Duty Circular Saw (7-¼" 1600w) 5 4,104.00 20,520.00 127 Pcs Abrasive Disc Cutter Machine (ssc22 14-inch Cut Off Saw Machine 2200w) 5 7,577.00 37,885.00 128 Pcs Manual Canvas Pliers (industry Line Combination Plier Insulated Pliers) 5 416.00 2,080.00 129 Pcs Jet-bow Beam Compass Drawing Set. The Set Includes 6" Speed Compass With Inter-changeable Pen, Pencil, Divider Parts, And Replaceable Needle Points. 4½" Bow Compass With Inter-changeable Pen, Pencil, And Divider Parts. 5 1,169.00 5,845.00 130 Pcs Human Head Model(2 Pack 17" Foam Head Female Wig Head 5 4,791.00 23,955.00 131 Pcs Screw Drivers Set( 9 Pcs Multi-purpose Magnetic Screwdriver Set 5 226.00 1,130.00 132 Pcs Pliers. Pliers And Grip Set (premium 4 Pcs Insulated Pliers Set) 5 2,904.00 14,520.00 133 Pcs Artist Stool With Wheels (stainless Steel Stool Bar) 5 1,991.00 9,955.00 134 Pcs Screen Print Squeegee (curved Aluminum Handle Squeegee 75) 5 308.00 1,540.00 135 Pcs Mixing Paint Palette (paint Mixing Palette 10 Well Plastic) 5 45.00 225.00 136 Pcs Carving Chisels For Wood (wood Chisel 4 Pcs/set) 5 798.00 3,990.00 137 Pcs Files Set For Wood Carving, Craft Metal, And Glass Stone (10-piece Needle File Set For Jewelries) 5 191.00 955.00 138 Pcs Heavy Duty Multi- Purpose Bench Vise (8") Mounted On A Steel Platform. 2 15,000.00 30,000.00 139 Pcs Anvil (15 Kg) With Steel Mounting Platform 2 12,000.00 24,000.00 140 Unit Electric Angle Grinder. Heavy Duty 4" 1000w Professional Power Tools Grinders Variable-speed 3 2,500.00 7,500.00 141 Box Cutting Disc For Steel. Ultra-thin Cutting Disc 4 (25pcs) For Stainless 5 2,000.00 10,000.00 142 Pcs Cutting Discs For Masonry. 4”-inch Professional Diamond Cutting Disc Continuous Eco For Tile / Ceramic 20 300.00 6,000.00 143 Set Drill Bits.3-12mm Multifunctional Triangle Glass Metal Drill Bit Set Diamond Ceramic Tile Concrete Brick Wood Punching Hole Drill Bits 5 500.00 2,500.00 144 Set Drill Bits. 13pc Cobalt High Speed Steel Twist Drill Bit Set 1.5mm-6.5mm For Drilling Metal Wood Stainless Steel 5 500.00 2,500.00 145 Set Drill Bits For Wood. 7pc X Long Wood Drill Bit Set 4mm 5mm 6mm 7mm 8mm 10mm 12mm X 300mm Brad Point Auger Drill Bits Wood 5 500.00 2,500.00 146 Set Electric Wood Power Planer. Wood Planer For Woodworking. 1200 Watts. 1300 Rpm. 50 Hz. 80mm Wide. With Accessories. With Warranty 3 3,000.00 9,000.00 147 Unit Impact Drill 13mm Hammer Electric Drill Heavy Duty 220v Household Power Tools Industrial Screwdriver. 7.5 Amp Copper Motor, 700w, 3300rpm. With Warranty 3 3,000.00 9,000.00 148 Box Welding Rod Special N-6013 (2.5) (3/32 X 13”) 10kg Per Box 4 2,500.00 10,000.00 149 Unit Electric Welding Machine. Portable Igbt Inverter Welding Machine (dc Inverter Welding) With Accessories. With 3 Mos. Warranty 3 5,000.00 15,000.00 150 Pcs Welding Protective Suite (genuine Whole Leader Welding Apron) 5 2,362.00 11,810.00 151 Pcs Welding Hood Cape (standard Size) 5 311.00 1,555.00 152 Pcs Welding Gloves 5 186.00 930.00 153 Pcs Welding Protective Visor Glasses, Standard 5 420.00 2,100.00 154 Pcs Welding Mask (welding Helmet Auto Darkening Adjustable) 5 465.60 2,328.00 155 Pcs Hard Hat (heavy Duty Safety Helmet With Chin Strap) 5 291.00 1,455.00 156 Pcs Compact Electric Kilns (quick Fire A Kiln Controller) 2 39,305.00 78,610.00 157 Pcs Heat Press Transfer Machine (multi-function Heat Press Machine Flatbed: 30 Cm X 38 Cm) 2 11,808.00 23,616.00 158 Pcs Hammer For Carpentry. Claw Hammer /16oz 5 300.00 1,500.00 159 Set Hacksaw Frame With Blade For Metal 12" 300mm Heavy Duty 5 350.00 1,750.00 160 Pcs Wooden Hand Saw. 18" High Quality Metal Blade With Plastic And Rubber Handle 5 350.00 1,750.00 161 Pcs Steel Measuring Tape. Fluorescerous Tape 10m Portable Self Lock Tape Measure Meter Tape Tools 5 350.00 1,750.00 162 Pcs Tri Square. High Quality Metal Frame 12" With Clear Markings 5 750.00 3,750.00 163 Pcs Level Bar. Aluminum Level Bar With Magnet Heavy Duty 80cm 2 2,000.00 4,000.00 164 Pcs Plumb Bob / Hulog. With String 350g 5 250.00 1,250.00 165 Set Rachet. Combination Wrench Steel Chrome Vanadium 8-24mm (per Piece) 5 500.00 2,500.00 166 Set Ratchet Wrench. 12pcs 1/2 1/4-inch Drive Ratchet Wrench Cr-v Socket Kits Mechanic Spanner Car Motorcycle Repair Tool 5 700.00 3,500.00 167 Pcs Adjustable Wrench. Industrial Adjustable Wrench (12") 300mm Made Of High-quality Steel. 5 350.00 1,750.00 168 Set Back Wrench. Set Of Heavy-duty Double Ring Spanner Wrench (metric 28mm - 32mm) Cr-v 5 500.00 2,500.00 169 Set Combination Wrench Tool Set 16pcs (8-32mm Professional Dual Purpose 5 700.00 3,500.00 170 Set Magnetic Screwdriver Set Professional Cushion Grip 5 Flat Head And 4 Phillips Tips Screwdriver Non-slip 5 1,000.00 5,000.00 171 Set Allen Wrench. Short Arm Hex Allen Key Set With Carbon Steel Material. (1.5 To 6 Mm 7 Pcs Set) 5 100.00 500.00 172 Set Heavy Duty Pliers. 8"standard Pliers Cutter Longnose Combinations 8"pliers 5 500.00 2,500.00 173 Pcs Water Pipe Wrench 18” Liyabe Tubo Yabe Hand Tools 5 500.00 2,500.00 174 Set Chisel For Wood. 90 Mm Wooden Handle. 12pcs Professional Manual Wood Carving Hand Chisel Carving Tool Set, 8mm-14 Mm High Quality Steel Blade. 5 900.00 4,500.00 175 Set Wood Planer Set -katam. Locally Manufactured 8 Inches 2 500.00 1,000.00 176 Pcs Rubber Mallet (16 Oz) 5 258.00 1,290.00 177 Pcs Ball Peen Hammer (½ Lb. (80 Oz) 5 376.00 1,880.00 178 Pcs Cutting Mat 6680412 5 268.00 1,340.00 179 Pcs Heavy Duty Extension Wire (10-meter Wire: 162 C, Plug: 15a, 25 V, Maximum Wattage:3750 W., At Least 4 Outlets) 5 900.00 4,500.00 180 Set Microphone With 5-meter Cord, Anti-interference, Anti-whistling. 2 1,500.00 3,000.00 181 Pcs Portable Sound System With Microphone ( Active Portable Trolley Speaker , 600w Max Power, Bluetooth + Tws, Usb & Sd Playback, Fm Radio, Line-in & Line -out, 2 Guitar Input, 2 Wired Mic Input, 180 Channels, Mic Priority, High Quality Lead Acid 12ah Battery, 12 Dc Input, Dimensions: (l) 36.5cm (w) 40 Cm (h) 67.5 Cm, 2 Fee Wireless Mic) 2 20,000.00 40,000.00 182 Pcs Camera Flash. 92 Ft./28 M) 2 13,800.00 27,600.00 183 Pcs Camera Lens (18-200mm F/3.5-5.6 Lens 2 40,336.00 80,672.00 184 Pcs Camera Tripod (aluminum Tripod Digital Camera Tripod Mobile Phone Selfie Stands) 2 2,500.00 5,000.00 185 Pcs Studio Lights (soft Light) 4 10,200.00 40,800.00 186 Hdmi Cord. Hdmi Male To Male Cable Hd104 10110 10 Meter. 4k/60hz 2 1,500.00 3,000.00 187 Hdmi Cord. 5 Meters. Two-color Injection Plug Double Shielded Cable Body. Hdmi2.0 Version. Resolution: 0.75m-3m Support 4k 60hz; 5m Support 4k 30hz Only. Awg:30awg (0.75m-5m) 5 600.00 3,000.00 188 Pcs Soft Box Stand And Reflector Holder (50x70 Cm Soft Box Lighting Kit) 2 442.00 884.00 189 Pcs Monolights (200 W) 2 3,931.00 7,862.00 190 Pcs Reflector With Holder (holder /arm Stand Kit) 2 2,891.00 5,782.00 191 Pcs Boom Light Stand And Reflector Holder (420 Lb. Light Boom Stand With Weight Bag Up To 5kg Maximum Lead Capacity) 3 5,508.00 16,524.00 192 Pcs Background (4.22 M Background Paper 1.36 X 10m) 3 1,438.00 4,314.00 193 Pcs Display Panel Board (display Parallel Board) 1 14,290.00 14,290.00 194 Pcs Offline Mini Compressor (air Compressor Kwv550 9l Oil Less 3 4,558.00 13,674.00 195 Pcs Styrofoam Cutter (electric Foam Cutter Hot Wire Pen Portable) 5 238.00 1,190.00 196 Pcs Potter's Wheel/ Electric Potter's Wheel / Cutter (220 Volts Pottery Wheel) 1 6,228.00 6,228.00 197 Pcs Fire Blanket (with Pvc Pouch 1.2m X 1.2 M) 3 624.00 1,872.00 198 Pcs Smoke Detector X-sense Xs01 Mini Smoke Detector- Stand Alone 3 1,799.00 5,397.00 199 Pcs Disposal Bins (trash Bins 75 L) 3 1,804.00 5,412.00 200 Pcs Dressing Mirror (whole Body Mirror With 4 Wheels Height 5ft. Width 14 Inches) 1 1,500.00 1,500.00 201 Pcs Dish Towels (10 Pc. Per Set 25 Cm X 25 Cm Microfiber Super Absorbent) 10 993.00 9,930.00 202 Pcs Steamer. 3 Layer Steamer 32cm Stainless Steel Cooking Pots Cookware Steam High Quality 3 1,156.00 3,468.00 203 Pcs Soap Dish (dual Soap Case With Cover & Handle- Bathroom Soap Dish / Soap Case) 50 70.00 3,500.00 204 Pcs Detergent (detergent Powder Set 6 Kilos-i Kilo X 6 Pouches) 50 288.00 14,400.00 205 Pcs Hand Soap (liquid Hand Soap Antibac 1 Gallon) 50 216.00 10,800.00 206 Pcs Pots (extra Size #4 (26cm Diameter 16 Cm In Height) 20 673.00 13,460.00 207 Pcs Pans (nonstick) 5 194.00 970.00 208 Pcs Toilet Paper Holder (wall Mounted Bathroom Toilet Paper Holder Tissue) 2 238.00 476.00 209 Pcs Dipper (plastic Dipper L 11" X W 36"x H 41" 2 15.00 30.00 210 Pcs Pail (utility Pail With Metal Handle 10l/26x27 Cm) 2 111.00 222.00 211 Pcs Trash Can (with Plastic Swing Lid L-27 Cm, W- 17.5cm, H- 40.5 Cm) 2 260.00 520.00 212 Pcs Toothbrush (extra Clean Toothbrush 5 Pk -soft) 20 182.00 3,640.00 213 Pcs Hairbrush (natural Wood Hairbrush Comb) 20 120.00 2,400.00 214 Pcs Comb (1 Dozen Suklay 3-hole X Sz-28 Big) 20 90.00 1,800.00 215 Pcs Toothpaste (red 100 Ml) 20 60.00 1,200.00 216 Pcs Plastic Tumbler 20 300.00 6,000.00 217 Pcs Razor (twin Blade Disposable Razors) 20 120.00 2,400.00 218 Pcs Nail Clipper (stainless Nail Clippers H-8 Cm Wt-0.046 Kg) 20 100.00 2,000.00 219 Pcs Nail File (12 Pcs Red Nail File (medium) 20 50.00 1,000.00 220 Pcs Deodorant (roll On 50 Ml Bottle) 20 150.00 3,000.00 221 Pcs Face Towel (basic Face Towel - Free Size) 20 100.00 2,000.00 222 Pcs Feminine Napkin (silk Floss 12 Pcs) 200 50.00 10,000.00 223 Pcs Dust Catcher With Broom (2n1 Broom Dustpan Set Windproof Floor Sweeper With Broom) 5 170.00 850.00 224 Pcs Feather Duster (soft Magic Feather Duster Long Size And Colorful Colors (plastic) 5 150.00 750.00 225 Pcs Wash Rags (round Rags) 5 30.00 150.00 226 Pcs Floor Map (magic Spin Mop With Bucket 360° Rotating Floor Cleaning Plastic Liner) 5 264.00 1,320.00 227 Pcs Garbage Can (super Convenient Mini Flip Lid Trash Can (plastic) 10 150.00 1,500.00 228 Pcs Sponge (high Density Double-sided Dishwashing Sponge 7x10x3 Cm) 10 30.00 300.00 229 Pcs Spray Bottle (garden Sprayer Capacity: 500ml) 10 170.00 1,700.00 230 Pcs Table Napkin (1 Ply 40s Sheets Folded) 10 21.00 210.00 231 Pcs Place Mat (table Placemat Pvc Anti-slip Placemat Washable Durable Kitchen S:30x45cm) 10 25.00 250.00 232 Dozen Plates (12 Pcs Plates 8-inch Melamine White) 6 358.00 2,148.00 233 Set Drinking Glass (drinking Glass 10 Oz Tall Clear Tumblers Set Of 6 L=5.5cm H-12 Cm) 6 510.00 3,060.00 234 Pcs Pitcher (durable Crystal-clear Glass 1.5l) 6 258.00 1,548.00 235 Pcs Bowl (serving Bowls, Clear Glass 20 Cm Diameter) 6 72.00 432.00 236 Pcs Water Dispenser. Hot And Cold Water/drinking Household Multifunctional Top Loading. Stainless Steel Casing Color White. Dimension: 85x29x29 Cm. Large Bottom Locker. 3 3,000.00 9,000.00 237 Pcs Electric Hand Drier (free Installation) 1 5,000.00 5,000.00 238 Pcs Water Pail. (utility Pail With Metal Handle 10l Color: Red/ Blue L-27cm, W-27cm, H-26 Cm 6 335.00 2,010.00 239 Bot Dish Washing Liquid. Kalamansi Lemon Antibac Hygiene 780ml Bottle 10 350.00 3,500.00 240 Pack Laundry Powder Soap. 5 Kg Supra Clean, Natural Scent 10 600.00 6,000.00 241 Pcs Laundry Bar Soap (scrubber Bar 125g) 120 18.00 2,160.00 242 Pcs Clothesline (1 Pc Nonslip Clothesline 35 M) 20 10.80 216.00 243 Pcs Clothes Pin (laundry Clothes Pins Spring Clips 24 Pcs Plastic) 20 48.00 960.00 244 Pcs Wash Basin (laundry Basin 23 Inch) 10 504.00 5,040.00 245 Pcs Laundry Bag Set (4 Pcs/set Laundry Washing Bag- 1 Pc M(30cmx40cm) 1pc L (40cmx50cm) 1pc Xl (50x60 Cm) 10 150.00 1,500.00 246 Pcs Ironing Board (ironing Board With Stand Portable 43"iron Board (70cm To 86 Cm) 5 1,300.00 6,500.00 247 Pcs Flat Iron (non-stick Teflon Saleplate Spray Function Ht & Width 251x170x120mm 5 870.00 4,350.00 248 Pcs Mono Bock Chair, Standard Size. White. Load Capacity 200kg. 20 600.00 12,000.00 249 Pcs Curtain Rod (steel +anti-rust Coating, Adjustable Size: Large 120 Inches) 10 1,200.00 12,000.00 250 Pcs Curtain (1pc 5x7 Ft. Window Curtain With 8-hole Grommet Rings For Bedroom And Living Room) 10 714.00 7,140.00 251 Dozen Hangers (12 Pcs. Plastic Hanger) 2 150.00 300.00 252 Pcs Washing Machine. 7.0 Kg Digital Inverter Fully Automatic Top Load Washing Machine (water Level: 5, Gross Weight: 31kg, Net Weight: 27 Kg Gross Dimension: (wxhxd)=580x890x600mm Net Dimension: (wxhxd)= 540x857x568mm) 2 20,000.00 40,000.00 253 Pcs Vacuum Cleaner (heavy Duty Gas 12-25 Pl Wet And Dry Vacuum Cleaner/ Extractor With Power Socket System 1,250 W Weight-9kg, Max Input Power- 1,250 W, Max Vacuum Power-200 Mbar) 5 11,547.00 57,735.00 254 Pcs Socks (cotton Socks Unisex High Street Socks Sixe:38-44 2 50.00 100.00 255 Pcs Dress (sleeve Ruffle Hem Plain Elegant) 1 500.00 500.00 256 Pcs Slippers (sizes 10, Flipflop Brand Light Weight And Durable 2 132.00 264.00 257 Pcs Mattress (for Single Size Bed Size Polyester 3.5 Inch Thick 6 4,440.00 26,640.00 258 Bed Foam (for Single Bed, 3 Inches Thick) 3 3,500.00 10,500.00 259 Pcs Pillows (foam Pillow 4x12x20) 3 426.00 1,278.00 260 Pcs Bedsheets (cotton Full Garterize 3n1 Bed Sheets, L-60in Ww-75in (for Single Bed Size) 3 300.00 900.00 261 Pcs Alarm Clock (3-inch Retro Mute Quartz Bell Alarm Clock Movement Bedside With Night Light And Loud Alarm) 1 450.00 450.00 262 Pcs Handheld Rechargeable Pool Vacuum. • Strong Built-in 4v 2ah Ni-mh Rechargeable Batteries • Suitable For Use With All Purespas And Above Ground Pools Up To 18 Feet Or 5.49 Meters In Diameter • 0.21 Gal (0.8 Liters) Quick Release Transparent Debris Container • 12 Gal/min. (45 Liters/minute) Water Suction For Efficient Debris Collection • 94 Inches (2.39m) Lightweight Telescoping Aluminum Pole • Two Interchangeable Brush Heads • Automatic Shut-off Feature When Vacuum Is Not Submerged In Water • Ipx8 Waterproof Switch For Added Protection • 5-6 Hour Charge Time / 50 Minutes Maximum Running Time • Usb Charging Cable Included For Convenient Recharging (plug Not Included) 3 9,998.00 29,994.00 263 Pcs Swimming Pool Leaf Skimmer. Purpose: Used For Cleaning Swimming Pool And Salvaging Pool Water Garbage. Material: Pp Plastic. Size: 420*280*30mm/16.54*11.02*1.18". 5 376.00 1,880.00 264 Pcs Pack Of 300 Pcs Chlorine Tablet For Swimming Pool. Adjustable Chlorine Dispenser 8 Inchin Combination With Mont, 3-inch Chlorine Tablets Adjust The Water Flow Rate And Hereby The Amount Of Chlorine Dissolved In Your Pool Package Included:1*chlorine Dispenser +300pcs Pool Cleaning Tablet Or 300pcs Pool Cleaning Tablet 20 500.00 10,000.00 265 Pcs Adaptive Swim Life Jacket For Disabled. Keeps The User’s Face Out Of The Water. Stops The Tension Of The Neck. Upright Position. Back Support. Therapist Hands Free! Double Harness Distributes Tension’s Adjustment. Possibility To Add The Harness Pad (or “cuissard” In French) No Latex. 5 11,000.00 55,000.00 266 Pcs Bakery Display Rack (estante). Made Of Glass And Aluminum Frame. 4 Layer Of Glass (transparent) Or Acrylic With Partition. Rubber Wheels With Lock. At Least 2ftx 5ftx 4 Ft 2 40,000.00 80,000.00 267 Pcs Bread Rack. Made Of 12 Mm Steel. 24"x5ftx5ft. Can Hold Up To 10 Trays (lagayan Ng Plantsa Ng Tinapay) 2 10,000.00 20,000.00 268 Pcs Cookery Cabinets (made With Carbon Steel 5 Layers, Size: H: 144cm, W: 55cm) 3 3,621.00 10,863.00 269 Set Housekeeping Cart. Multi-functional Movable Cleaning Cart Housekeeping Property Cleaning Tool Cart Special Trolley. Standard For Housekeeping Work. 5 5,000.00 25,000.00 270 Set Shopping Cart Utility Cart Trolley Grocery Cart For Warehouse Garden Supermarket 5 6,000.00 30,000.00 271 Pcs Kitchen Carts (2 Layer Stainless Steel Carts With Two Brake Wheels; Size: 400mm X 500mm X 860mm) 2 3,019.00 6,038.00 272 Pcs Weighing Scale Digital. Display Mode: Led/lcd+light. Weighing Range :40kg. Accuracy: 2g. Product Size: 35x33x14cm 3 Lcd Display On The Operator’s Side Of The Scale As Well As 3 Lcd Display On The Customer’s Side. Minimum Capacity Is 2g. Maximum Capacity Is 40kg Power Source: Built In Rechargeable Battery With Usb Cable Battery Powered Or Connect Usb Cable. Battery Powered Or Connect Usb Cable To Use Weight Platform/tray Material Is Stainless Steel. 4 7,000.00 28,000.00 273 Pcs Measuring Cup. Measuring Cup Sizes: 1 Cup (250ml). 1/2 Cup (125ml). 1/4 Cup (60ml); 1/8 Cup (30ml). Materials. Plastic (abs) 6 500.00 3,000.00 274 Pcs Measuring Spoon 1tbsp 15ml 1/2tbsp 7.5ml Ltsp 5ml 1/2tsp 2.5mlmaterial: Stainless Steel+pp Packing: Pp Bag 6 400.00 2,400.00 275 Pcs Measuring Urn - Glass, Capacity: 100 Ml. (with 10 Ml Increments), Metric And English System Of Measurement; With Handle And Spout, Clear, Non- Porous, Tempered Glass 6 450.00 2,700.00 276 Pcs Wire Whisk - Length: 30 Cm (12 ") Material Stainless Steel 6 320.00 1,920.00 277 Pcs Chef's Knife (stainless Steel) 33cm X 4.5cm X 2cm 6 750.00 4,500.00 278 Pcs Boning Knife (stainless Steel) 24.4cm X 1.9cm X 1.7cm 6 492.00 2,952.00 279 Pcs Oysters Knife (stainless Steel) 15.5com X 6.5cm X 3cm 6 187.00 1,122.00 280 Pcs Cleaver Knife (stainless Steel) 7 Inches Or 2.5mm 6 1,074.00 6,444.00 281 Pcs Tenderizer (pin Tenderizer) Stainless Steel Diameter: 5cm, Height: 19cm 6 119.00 714.00 282 Pcs Tenderizer Mallet. (tenderizer) Stainless Steel 12.6 Inches X 11.5x4cm 6 240.00 1,440.00 283 Pcs Skimmer, Fine (stainless Steel) 7.3cm X 5cm X 21.5cm 6 160.00 960.00 284 Pcs Wire Skimmer, Small (stainless Steel) Handle: 14; Radius: 14 6 105.00 630.00 285 Pcs Skimmers, Spider (stainless Steel) Handle: 14; Radius: 20 6 115.00 690.00 286 Pcs Strainer, Small, Fine (stainless Steel) Diameter:14cm; Length: 29cm; Depth: 5.5cm 6 160.00 960.00 287 Pcs Colander Strainer (stainless Steel) 48cm X 20cm X 12cm 6 298.00 1,788.00 288 Pcs Siever, Small (stainless Steel) 14 Cm 6 188.00 1,128.00 289 Pcs Strainer, Medium, Fine (stainless Steel) Diameter:16cm; Length: 30.5cm; Depth: 5.9cm 6 180.00 1,080.00 290 Pcs Turner (stainless) Dimension: 34.5 X 9.8 X 4.4 Cm 6 280.00 1,680.00 291 Pcs Spatula (silicon) 27.2 X 5.5 X 1.5cm 6 169.00 1,014.00 292 Pcs Wooden Spoon (made With Beech Wood 10cm X 34cm X 2cm) 6 244.00 1,464.00 293 Pcs Parisienne Scoop (stainless Steel Blade With Plastic Handle) Scoop Diameter: 30mm And 27mm; Total Length: 170mm 6 216.00 1,296.00 294 Pcs Fruit Juicer, Standard Type 6 1,500.00 9,000.00 295 Pcs Zester (stainless Steel) Length: 30cm/11.81 Inches 8 268.00 2,144.00 296 Pcs Piping Bag (disposable Bag Size: 24.5cm X 17cm 8 208.00 1,664.00 297 Pcs Pastry Tubes (stainless Steel) 3cm X 3cm X 6.1cm 8 142.00 1,136.00 298 Pcs Strainer, Chinois, Small (stainless Steel) 16cm Handle: 5.5inches 8 198.00 1,584.00 299 Pcs Filling Funnel (stainless Steel) Upper Diameter: 10.5cm, Lower Diameter: 3.7cm, Height: 4.5cm 4 212.00 848.00 300 Pcs Measuring Spoon (1set: 1tbsp, 1/2tbsp, 1tsp, 1/2tsp, 1/3tsp, 1/4tsp) 6 245.00 1,470.00 301 Pcs Tongs (stainless Steel) 9 Inches 10 110.00 1,100.00 302 Pcs Tongs (stainless Steel) 12 Inches 8 179.00 1,432.00 303 Pcs Ice Cream Scoop (stainless Steel) Diameter: 4.5cm, Length: 18cm 6 208.00 1,248.00 304 Pcs Cheese Cloth (made From Cotton) 101 X 270cm 10 223.00 2,230.00 305 Pcs Serving Spoon (heavy-duty Stainless Steel) Length: 22.5cm; Width: 6cm 24 102.00 2,448.00 306 Pcs Pepper And Salt Grinder (made With Stainless Steel, Glass And Ceramic) Approx. 19x6.5cm 6 296.00 1,776.00 307 Pcs Core Seed Remover (stainless Steel; Approx: 1.4x21.5cm) 8 229.00 1,832.00 308 Pcs Wire Whisk, Small (stainless Steel+plastic Handle; 8 Inches) 8 180.00 1,440.00 309 Pcs Wire Whisk, Medium (stainless Steel+plastic Handle; 10.2 Inches) 8 189.00 1,512.00 310 Pcs Wire Whisk, Heavy Duty (stainless Steel+plastic Handle; 14 Inches) 2 258.00 516.00 311 Pcs Can Opener (stainless Steel Blade; Length: 17cm High) 1 370.00 370.00 312 Pcs Muti-purpose Kitchen Scissors/ Shears (scissors Length: 21.5cm; Blade Length: 10cm; Handle Length: 11.5cm; Handle Width: 9.5cm; Blade Thickness: 0.4cm Weight: 200grams) 8 368.00 2,944.00 313 Pcs Soup Ladle, 4 Oz (stainless Steel; Size: 7.5cm X 30 Cm) 8 124.00 992.00 314 Pcs Soup Ladle, 6 Oz (stainless Steel; Size: 7.5cm X 30 Cm) 8 194.00 1,552.00 315 Pcs Soup Ladle, 8 Oz (stainless Steel And Wooden Handle: 10 X 51 Cm) 3 290.00 870.00 316 Pcs Soup Ladle, 12 Oz (stainless Steel And Wooden Handle: 15 X 51 Cm) 2 360.00 720.00 317 Pcs Kitchen Spoon (stainless Steel; Size: 8cmx6.5cmx21cm) 8 86.00 688.00 318 Pcs Kitchen Spoon, Slotted (material: Plastic; Size: 7x3x43cm) 8 289.00 2,312.00 319 Pcs Kitchen Fork (stainless Steel; Size: 7cmx4cmx21cm) 4 72.00 288.00 320 Pcs Carving Fork (stainless Steel; Size: 13 Inches Long) 3 162.00 486.00 321 Pcs Digital Kitchen Thermometer (cooking/food Temperature; Size 34mm X 270mm) 2 486.00 972.00 322 Pcs Muti-function Vegetable Fruit Peeler Slicer Cutter Chopper (material: Abs + Stainless Steel) 2 429.00 858.00 323 Pcs Stock Pot, Big (with Glass Cover; Size: 34.5 X 27.9 Cm X 16.6 Cm) 2 798.00 1,596.00 324 Pcs Frying Pan, Small (scratch Resistant And Non-stick; Size: 20cm) 4 233.00 932.00 325 Pcs Frying Pan, Medium (scratch Resistant And Non-stick; Size: 24cm) 4 380.00 1,520.00 326 Pcs Frying Pan, Large (scratch Resistant And Non-stick; Size: 28cm) 2 578.00 1,156.00 327 Pcs Colander, Small (stainless Steel; Size: 24cm X 22cm) 3 204.00 612.00 328 Pcs Colander, Medium (stainless Steel; Size: 28cm X 22cm) 2 298.00 596.00 329 Pcs Cutting Board (material: Bamboo; Size: 34x24x1.8cm/750g) 4 209.00 836.00 330 Pcs Heavy Duty Electric Grill Machine 2 10,000.00 20,000.00 331 Pcs Portable And Foldable Charcoal Barbeque Grill 25"x30"x27" 2 2,000.00 4,000.00 332 Unit Cotton Candy Machine, Power 950 Watts, Speed 3600 Rpm, Pre Heating Time 1 To 3 Minutes, 515 Mm Diameter Stainless Drum. 1 5,000.00 5,000.00 333 Pcs Fish Poacher, Medium (stainless Steel With Tempered Glass Cover; Size: 24cm X 38.7cm X 10cm) 1 983.00 983.00 334 Pcs Casserole, Small (stainless Steel: 2.1 Liter; Size: 12cm X 15cm) 6 599.00 3,594.00 335 Pcs Casserole, Medium (stainless Steel: 3.9 Liter; Size: 12.5cm X 20cm) 4 689.00 2,756.00 336 Pcs Wok, Small (nonstick Carbon Steel; Size: 32cm) 4 389.00 1,556.00 337 Pcs Wok, Medium (nonstick Carbon Steel; Size: 36cm) 1 401.00 401.00 338 Pcs Double Boiler, Medium (stainless Steel; Size: 27x14x6cm) 1 389.00 389.00 339 Pcs Paella (heavy Duty Carbon Steel; Size 25cm) 8 581.00 4,648.00 340 Pcs Glass Rack (plastic-coated Metal; Capacity: 24pcs Glass; Dimension: L:52cm; W: 36cm; H:8cm) 2 461.00 922.00 341 Pcs Soup Cup Rack (2 Layered Rack; Size: 35 X 25 X 28cm) 3 899.00 2,697.00 342 Pcs Plate Rack (stainless Steel; Size: 30cmx22.8cmx12.9cm) 2 492.00 984.00 343 Pcs Baking Tray, Small (stainless Steel; Size Details: 23cm X 17cm) 8 258.00 2,064.00 344 Pcs Utility Tray (stainless Steel: Stain Resistant; Size: 45cm X 35cm X 4.8cm) 12 189.00 2,268.00 345 Pcs Roasting Pan (stainless Steel; Size: 31.5 X 24.5 X 2.5 Cm) 4 378.00 1,512.00 346 Pcs Dish Towels (highly Absorbent Cloth With 3pcs Per Pack) 8 98.00 784.00 347 Pcs Cooler, 2.5ft X 2.5 Ft X 3ft Plastic, With Good Insulation 1 3,000.00 3,000.00 348 Pcs Plastic Silverware Or Real Silverware (stainless Steel; 18pcs Utensils Set Includes: 6 Dinner Fork, 6 Dinner Spoons And 6 Dinner Teaspoons) 2 415.00 830.00 349 Pcs Glasses. Dining Glasses (6pcs. Thick Clear Glass: W: 3inches And H: 4inches) 6 265.00 1,590.00 350 Pcs Teacups (ceramic White; Capacity: 250ml) 2 188.00 376.00 351 Pcs Small Plate / Saucers (ceramic With Size: 6 Inches And 6pcs Per Set) 6 140.00 840.00 352 Pcs Cabinet Dish Organizer (2 Layered Metal Dish; Size:41.5cm X 30cm X 47cm) 1 2,499.00 2,499.00 353 Pcs Sponge And Soap Holder For Kitchen (stainless Steel) 18x 10 X 9cm 3 418.00 1,254.00 354 Pcs 11-piece Pots/pans (stainless Steel) 1 5,158.00 5,158.00 355 Pcs Silicone Kitchenware Set. Composed Of Slotted Spoon 12". Soup Ladle 12". Solid Turner 12". Tongs 10". Whisk 9.5". Basting Brush 10.8". Pasta Server 12.5". Round Spatula 12". Spoon 12.5" Spatula 12.6" And Utensils Holder. 6 647.50 3,885.00 356 Pcs Rotary Eggbeater (stainless Steel) 31cm /12.2", W:9.5cm/3.74" 2 340.00 680.00 357 Pcs Dough Scraper (stainless Steel) 16x12x2cm 3 178.00 534.00 358 Pcs Gas Range And Oven (1 Turbo, 1 Large And 2 Medium Burners) 33x42x39.5, (49 Liters ) 1 46,162.00 46,162.00 359 Pcs Refrigerator (7 Cubic Feet, Stainless Look) Two Door Direct Cool 1 15,717.00 15,717.00 360 Pcs Kitchen Cupboards (7 Doors, 3 Drawers) 120x 40x90 Cm 2 13,198.00 26,396.00 361 Pcs Cooking Brush (silicone) Heat Resistant 3 82.00 246.00 362 Pcs Blender. (9 In1 Food Processor, Good For Chopping, Slicing,grating,shredding, Whisking)18x18x38cm 3 3,742.00 11,226.00 363 Pcs Mechanical Microwave Oven (countertop,20 Liters) 700w - 1200w 3 5,075.00 15,225.00 364 Pcs Kitchen Scale Food (manual) 5 Kilogram 2 252.00 504.00 365 Pcs Measuring Spoons (stainless Steel, 6pcs Heavy Duty) 3 258.00 774.00 366 Pcs Measuring Cups (12 Pieces, Bpa -free Plastic Long Lasting Used) Large And Medium Cups 3 2,208.00 6,624.00 367 Pcs Kitchen Shears (stainless Steel) 9 Inches/ 225mm 3 357.00 1,071.00 368 Pcs Potato Masher With Soft Grip Handle (stainless Steel) 9.5x27x8cm 3 357.00 1,071.00 369 Pcs Medium Graters (stainless Steel) 18/8 3 430.00 1,290.00 370 Pcs Funnel (stainless Steel) 22x14.5cm 3 715.00 2,145.00 371 Pcs Can Opener (automatic) 16.3x 1.5cm 3 698.00 2,094.00 372 Pcs Cast Iron Pots And Pans (ceramic, Non-stick) 21.85x 13.19x12.80inch 3 7,180.00 21,540.00 373 Pcs Gas Stove. 2 Burner Built In Gas Stove ( Stainless Steel) 73x41x9cm With Hose And Safety Regulator. 5 3,640.00 18,200.00 374 Pcs Lpg Tank 11kg 6 5,000.00 30,000.00 375 Unit Electric Stove. Stainless Frame. Multifunctional Induction Cooker Inverter Electric Stove Heavy Duty Energy-saving 3500w 220v. All Copper Heating Coil. Five Speed Power Adjustment. Explosion Proof. With Digital Display Panel. 5 2,500.00 12,500.00 376 Pcs Double Broiler Steamer (stainless Steel) 30 Cm Diameter 3 2,730.00 8,190.00 377 Pcs Kitchen Knife Set (stainless Steel And Poly Propylene Plastic Handle) 15x7.5x34cm 3 840.00 2,520.00 378 Pcs Meat Slicer (electric Machine Stainless Steel) 418x 293x 325mm 3 2,494.00 7,482.00 379 Pcs Bread Toaster (stainless Steel Top Plate) 25x 14.6x16.8cm 3 1,059.00 3,177.00 380 Pcs Cookie Press (stainless Steel With 13 Disc And 8 Icing Tips 25x 14.5cm 3 462.00 1,386.00 381 Pcs Cake Decorating Kit. Piping Tips Set ( Stainless Steel, Multicolor) 3 279.00 837.00 382 Pcs Serving Bread Tray (stainless Steel) 45cmx2.8cm 6 1,229.00 7,374.00 383 Pcs Hot Plate Single Electric Stove (1000 W) 8.8x8.8x1.4 Inch 2 583.00 1,166.00 384 Pcs Electric Oven. Height (cm): 32.5. Highlights. Width (cm): 37.5. Warranty: 1 Year Warranty On Electrical Parts And Lifetime Free Service. Net Weight (kg): 7.3. Capacity: 2.8 Liters Length (cm): 49. Gross Weight (kg): 8.2. 5 11,000.00 55,000.00 385 Pcs Oven. Four Plates Oven For Bread (stainless Steel) 530x595x570mm. Lpg Type 1 48,924.00 48,924.00 386 Pcs Bread Plates (stainless Steel) 40x 60cm 20 1,027.00 20,540.00 387 Pcs Bread Rack (stainless Steel)15 Layers 40x60cm Heavy Duty 1 20,000.00 20,000.00 388 Pcs Electric Burger Griddle. Large Size Heavy Duty. Size: 73cmx52cmx10cm. Bigger Waster Oil Container. Stainless Steel, Solid Gritty. Food Grade Material. 2 11,475.00 22,950.00 389 Pcs Food Warmer Display Cabinet. Commercial Food Heater Glass Display Cabinet Heavy-duty Curved Deli Cabinet With Lighting. Constant Temperature Heating Display Counter Ideal For Fried Chicken Burger And Cooked Food. Size: Red+3 Compartments: 96x45x60cm. Rated Power: 300w. Rated Voltage: 220v.number Of Internal Layers: Three. Layers. Temperature Range: 30-80°c. Product Weight: 18kg. Built-in Energy-saving Warm Color Lamp, Improve The Display Effect 2 9,125.00 18,250.00 390 Pcs Frying Pan (non-stick, 28 Cm) 3 1,690.00 5,070.00 391 Pcs Measuring Spoon. 1tbsp 15ml. 1/2tbsp 7.5ml. Ltsp 5ml. 1/2tsp 2.5mlmaterial: Stainless Steel+pp. Packing: Pp Bag. 3 400.00 1,200.00 392 Pcs Measuring Cups (12 Pieces, Bpa -free Plastic Long Lasting Used) Large And Medium Cups 3 2,209.00 6,627.00 393 Pcs Measuring Urn. Glass, Capacity: 100 Ml. (with 10 Ml Increments), Metric And English System Of Measurement; With Handle And Spout, Clear, Non- Porous, Tempered Glass 3 450.00 1,350.00 394 Pcs Mixing Bowl: 30 Cm L30xw27.5xh11.4 Cm Thickness: 0.04 Cm. Material: Stainless Steel 12 900.00 10,800.00 395 Pcs Baking Sheet 11x15 Inches 011 Thickness Heavy Duty Aluminum 10 360.00 3,600.00 396 Pcs Wire Whisk Length: 30 Cm (12 ") Material Stainless Steel 5 320.00 1,600.00 397 Pcs Muffin Pan Non-stick Muffin Pan Dimension: 26.5x35x3cm Capacity: 12 Cup Color: Black Non-stick Surface For Easy Release And Quick Cleanup Dishwasher Safe Ideal For Baking Muffins, Cupcakes, And More Nonstick Coating Helps Ensure Effortless Food Release 5 700.00 3,500.00 398 Set Measuring Spoon 1tbsp 15ml 1/2tbsp 7.5ml Ltsp 5ml 1/2tsp 2.5mlmaterial: Stainless Steel+pp Packing: Pp Bag 6 400.00 2,400.00 399 Set Measuring Cups (12 Pieces, Bpa -free Plastic Long Lasting Used) Large And Medium Cups 6 2,209.00 13,254.00 400 Pcs Measuring Urn Glass, Capacity: 100 Ml. (with 10 Ml Increments), Metric And English System Of Measurement; With Handle And Spout, Clear, Non- Porous, Tempered Glass 6 490.00 2,940.00 401 Pcs Mixing Bowl 30 Cm L30xw27.5xh11.4 Cm Thickness: 0.04 Cm Material Stainless Steel 6 900.00 5,400.00 402 Pcs Baking Sheet 11x15 Inches 011 Thickness Heavy Duty Aluminum 10 360.00 3,600.00 403 Pcs Wire Whisk Length: 30 Cm (12 ") Material Stainless Steel 5 320.00 1,600.00 404 Pcs Electric Stove, 1000 Watts, 12" Diameter, Stainless Steel. With Safety Regulator And Power Indicator. 6 1,500.00 9,000.00 405 Pcs Weighing Scale, Digital "display Mode: Led/lcd+light Weighing Range :40kg Accuracy: 2g Product Size : 35x33x14cm 3 Lcd Display On The Operator’s Side Of The Scale As Well As 3 Lcd Display On The Customer’s Side Minimum Capacity Is 2g. Maximum Capacity Is 40kg Power Source: Built In Rechargeable Battery With Usb Cable Battery Powered Or Connect Usb Cable. Battery Powered Or Connect Usb Cable To Use Weight Platform/tray Material Is Stainless Steel." 4 7,500.00 30,000.00 406 Pcs Scraper(rubber) 30cm X11cmx6.8cm 5 130.00 650.00 407 Pcs Hand Mixer (stainless Steel Bowl) 270x165x290mm, 2.8 Liters Capacity 5 1,755.00 8,775.00 408 Pcs Revolving Cake Stand (aluminum) 12 Inches 5 850.00 4,250.00 409 Pcs Electric Stand Mixer 5.5 Liter(1.9kg) With Bowl And 3 Whisk 6 Speed Setting Dough, Rotating Bowl, Speed Control 3 11,500.00 34,500.00 410 Pcs Rolling Pin Stainless Steel Pressing Stick Pizza Dough Non-stick Dough Roller, (29.5 Cm) 6 300.00 1,800.00 411 Pcs Dough Roller Pin, Wooden. 29.5cm Non-stick Silicone Rolling Pin Pastry Baking Decorating Tool 6 300.00 1,800.00 412 Set Deep Fryer Dimensions (w X H X D) 477 X 318 X 235 Weight 3.81kg Body Material Stainless Steel Color Silver Technical Details Power Consumption 2000w Volume 4l Features Temperature Control Yes 6 7,200.00 43,200.00 413 Pcs Ice Crusher Machine. Electric Stainless Steel Heavy Duty Portable Automatic Rotated Speed: 1500rpm Power:250 Size: 275x190x210mm Capacity: 2 Liter 2 3,900.00 7,800.00 414 Pcs Chest Freezer (inverter) Dual Function Technology (freeze Or Chiller) Solid Top With Glass Cover Inside Digital Temperature Control W/ Lcd Display Dimension: 85:112:70cm 1 28,535.00 28,535.00 415 Set Electric Takoyaki Machine And Double Pan 56 Holes Stainless Steel Size: 437x 435x180mm 6 2,600.00 15,600.00 416 Pcs Waffle Iron Pan 4 Interchangeable Plates 750 Watts 6 1,800.00 10,800.00 417 Pcs Revolving Cake Stand. Nonslip Top And Base. Diameter: 23.5 Cm. Height 14cm. Material: Food Grade Pp. 6 1,076.00 6,456.00 418 Pcs Stainless 4-gas Burner, 55l Gas Oven Hybrid Electric And Lpg 1 40,000.00 40,000.00 419 Pcs Electric Kettle 1.5l 3 900.00 2,700.00 420 Pcs Stand-up Kitchen Mixer-standard (4 Liters Stainless Steel Bowl With Cover) Tilting Mixing Arm. Accessories: Beater, Dough Hook, Whisk. 12 Speed Setting. 2 10,000.00 20,000.00 421 Pcs Hand Mixer. Powerful 180w Motor And 7 Speeds Including Turbo Setting Made Of Stainless-steel Abs. Multifunctional With Chrome Accessories: X2 Beaters, X2 Dough Hooks 5 2,500.00 12,500.00 422 Unit Rice Cooker Standard 2l Home Multifunctional Home Cooking 220v. Fast Cooking, Keep Warm Function, Non-stick Coating, Stainless Steel Cover. Input Voltage. 220v. Power Consumption 400w. Volume Capacity 2l Dimension (l X W X H) 215*215*215 3 2,500.00 7,500.00 423 Unit Electric Rice Cooker 10l 2 5,000.00 10,000.00 424 Pcs Blender 1.5 Liter 5 700.00 3,500.00 425 Pcs Pressure Cooker 3.5 Liter 2 1,200.00 2,400.00 426 Pcs Gas Stove Rack. Plain Sheet With Steel Frame. With Cooking Platform At The Top. Kitchen Heavy Duty Gas Tank Holder Kitchen Organizer Stainless. Made Of Carbon Steel 45cmx45cmx90cm. Made Of Carbon Steel Color Black With Partition For 11kg Gasul Tank And For Cooking Materials. 4 5,500.00 22,000.00 427 Pcs Chef's Knife, 8" Stainless Steel 6 350.00 2,100.00 428 Pcs Bread Knife, 8" Stainless Steel 6 350.00 2,100.00 429 Pcs Clever Knife/ Butcher Knife To Chop Bones 20 Cm Blade, 31 Cm From Tip To Handle 6 350.00 2,100.00 430 Pcs Kitchen Scissors 9" Stainless Steel 6 350.00 2,100.00 431 Pcs Utility Knife 61mmx19mm 6 350.00 2,100.00 432 Pcs Boning Knife, 8" Japanese High Carbon Steel 6 350.00 2,100.00 433 Pcs Paring Knife 4" German Stainless Steel 6 350.00 2,100.00 434 Pcs Stainless Peeler For Vegetables 15cmx6cm 6 80.00 480.00 435 Pcs White Cutting Board (for Bread And Pastry) 25.5cmx34cm, Plastic 6 460.00 2,760.00 436 Pcs Green Cutting Board (for Fruits And Vege)25.5cmx34cm, Plastic 6 460.00 2,760.00 437 Pcs Red Cutting Board (raw Meat)25.5cmx34cm, Plastic 6 460.00 2,760.00 438 Pcs Blue Cutting Board (raw Fish)25.5cmx34cm, Plastic 6 460.00 2,760.00 439 Pcs Yellow Cutting Board (cooked Meat) 25.5cmx34cm, Plastic 6 460.00 2,760.00 440 Pcs Brown Cutting Board (raw Crops) 25.5cmx34cm, Plastic 6 460.00 2,760.00 441 Pcs Weighing Scale (dial/analog. 25kg) 1 400.00 400.00 442 Pcs Digital Kitchen Scale 3kg/0.1g And 500g/0.1g 3 690.00 2,070.00 443 Pcs Measuring Cups (1 Set) 6 95.00 570.00 444 Pcs Plastic Measuring Pitcher Jug With Measurement(set) Maximum Of 1 Liter 6 126.00 756.00 445 Pcs Measuring Spoon, Plastic (set) 6 60.00 360.00 446 Pcs Deep Fry Thermometer, Deed Fried Pot Thermometer Oil Temperature Gauge 6 320.00 1,920.00 447 Pcs Meat Thermometer, Brifit Waterproof Kitchen Meat Thermometer, Foldable Digital Instant Read Food Thermometer 6 400.00 2,400.00 448 Pcs Oven Thermometer 6 389.00 2,334.00 449 Pcs Tenderizer, Wooden Circular-50mm Diameter, 3cm Spikes, 190mm Long (flashlight Design) 6 280.00 1,680.00 450 Pcs Skimmer, Fine Mesh Strainer Oil-frying Filter 7cm Diameter, 32 Long 5 80.00 400.00 451 Pcs Wire Skimmer 18cm Diameter, Stainless Steel 5 80.00 400.00 452 Pcs Strainer, Stainless Steel Multi-purpose Food Strainer, Fine Mesh Long Handle 20cm Diameter X 28cm (fine) 5 109.00 545.00 453 Pcs Siever 17.5x12x11.5cm, Stainless Steel Mesh Stainer 6 68.00 408.00 454 Pcs Strainer Medium 20cm Diameter X 28cm (fine) 6 90.00 540.00 455 Pcs Strainer Large 25cm Diameter X 30cm Long, Stainless Steel 6 120.00 720.00 456 Pcs Wooden Turner, Wooden Sandok Kitchen Spatula Spoon Turner Cooking, 3" Width Of Sandok, 10" Long 6 65.00 390.00 457 Pcs Wooden Spatula 9cm Sandok, 34 Cm Long 6 65.00 390.00 458 Pcs Parisienne Spoon, Double-ended Headed Fruit Ice-cream Ball 6 50.00 300.00 459 Pcs Wooden Ladle/spoon 6cm Pang Sandok 30 Cm Long 6 120.00 720.00 460 Pcs Zester, Four-sided Stainless-steel Grater 9-inch Kitchen Multipurpose Grater For Parmesan Cheese, Ginger Vegetables 6 79.00 474.00 461 Pcs Reusable Piping Bags. 26 Pcs/set Silicone Pastry Bag Tips Kitchen Diy Icing Piping Cream 24 73.00 1,752.00 462 Pcs Stainless Funnel Small 4.5cm Opening Diameter, 3.7cm Height, 0.6cm Tube Diameter 6 60.00 360.00 463 Pcs Stainless Funnel Small 5.5cm Opening Diameter, 5cm Height, 0.9cm Tube Diameter 6 70.00 420.00 464 Pcs Stainless Funnel Small 7.5cm Opening Diameter, 6.7cm Height, 1.2cm Tube Diameter 6 60.00 360.00 465 Pcs 8" Tongs 6 89.00 534.00 466 Pcs 12" Tongs 6 120.00 720.00 467 Pcs Pepper Mill, 5-inch Wooden Peeper Grinder 6 60.00 360.00 468 Pcs Salt Mill 5-inch Wooden Salt Grinder 6 60.00 360.00 469 Pcs Wire Whisks 12 Inches 6 80.00 480.00 470 Pcs Wire Whisks 8 Inches 6 89.00 534.00 471 Pcs Can Opener 6 120.00 720.00 472 Pcs Bottle Opener 6 79.00 474.00 473 Pcs Soup Ladle 3oz 6 140.00 840.00 474 Pcs Soup Ladle 6oz 6 160.00 960.00 475 Pcs Soup Ladle 8oz 6 160.00 960.00 476 Pcs Soup Ladle 12oz 6 180.00 1,080.00 477 Pcs Stock Pot, 30cm High Quality Stainless Steel 10 1,500.00 15,000.00 478 Pcs Stock Pot 24cm High Quality Stainless Steel 10 999.00 9,990.00 479 Pcs Frying Pan 22cm Marble Frypan 10 500.00 5,000.00 480 Pcs Frying Pan 28cm Marble Frypan 48.2x28x5.7cm 10 600.00 6,000.00 481 Pcs Casserole 18 Cm Aluminum, Double Handle, Rust Free 10 250.00 2,500.00 482 Pcs Casserole 20 Cm Aluminum, Double Handle, Rust Free 10 300.00 3,000.00 483 Pcs Casserole 28 Cm Aluminum, Double Handle, Rust Free 10 600.00 6,000.00 484 Pcs Wok 40 Cm Chinese Nonstick Wok Pan 10 500.00 5,000.00 485 Pcs Double Broiler 28 Cm Stainless Steel Two-layer Double Soup Steamed Dual Purpose 10 280.00 2,800.00 486 Pcs Glass Rack. 25-compartment Gray Full-size Glass Rack With 2 Blue Extenders 2 2,500.00 5,000.00 487 Pcs Plate Rack. Microwire 24 Compartment Catering Plate Rack For Plates Up To 11" - Wash, Store, Transport 3 3,000.00 9,000.00 488 Pcs Baking Tray 15"x17" 5 180.00 900.00 489 Pcs Roasting Tray 15"x17'' 5 180.00 900.00 490 Pcs Braising Pan 32cm Stainless Steel Nonstick Pan 5 350.00 1,750.00 491 Pcs Hanging Cabinet With Glass, Std. 2.5'x 3' X 5ft (free Installation) 3 10,000.00 30,000.00 492 Pcs Floor Mops (broom Type) Using Cotton Absorbent Strips 10 180.00 1,800.00 493 Pcs Broom (walis Tambo) 10 80.00 800.00 494 Pcs Dustpan (plastic) 11"x10" Pan, 24" Handle 10 120.00 1,200.00 495 Pcs Garbage Bin (4 Gals.) 10 300.00 3,000.00 496 Pcs Paper Towel Dispenser 10 200.00 2,000.00 497 Pcs First Aid Cabinet, Plastic Box 30cmx12cmx30co With Transparent Cover (free Installation) 2 1,500.00 3,000.00 498 Pcs Fire Extinguisher 3lbs Abc Dry Chemical Refillable (free Installation) 4 2,000.00 8,000.00 499 Pcs Mixing Bowl Small, Stainless Steel Mixing Bowl 20cm 12 80.00 960.00 500 Pcs Mixing Bowl Medium, Stainless Steel Mixing Bowl 30cm 12 130.00 1,560.00 501 Pcs Stainless Steel Basin, 45 Cm Diameter 5 180.00 900.00 502 Pcs Stainless Steel Basin, 38 Cm Diameter 5 120.00 600.00 503 Pcs Baking/ Pastry Brush, Heat Resistant, Standard Size 10 35.00 350.00 504 Pcs Plastic Containers, Microwavable Round Canister, Food Storage Container (400 Ml) 40 20.00 800.00 505 Pcs Multipurpose Plastic Pail 2.5 Gallons Capacity 4 120.00 480.00 506 Pcs Food Grade Silicone High Temperature Resistant Baking Mat Oven Baking (to Match Baking Pan), Browns Silicone Baking Oven Mat Liner, Non-stick For Pastry Cookies Dough 12 90.00 1,080.00 507 Pcs Non-slip Doormat 75x45 Cm Rubber 18 500.00 9,000.00 508 Pcs White Hand Towels Hanging Kitchen Hand Dry 20cmx30cm 12 30.00 360.00 509 Pcs Potholder, Basahan Bilog 6 Inches Diameter 12 15.00 180.00 510 Pcs Round Cake Molder 4, 6, 8 Inches Set 5 161.00 805.00 511 Pcs Square Cake Molder 9, 11, 13 Inches Set 5 160.00 800.00 512 Pcs Baguette Bake Mold Pan 34.5 Cmx 24cm (6cm Molder) Nonstick 10 399.00 3,990.00 513 Pcs Meat Processing Machine (meat Grinder Manual) 1 5,000.00 5,000.00 514 Set Stainless Icing Tip (set-12pcs) Cake Decorating Kit Stainless. Icing Piping Nozzles Pastry Tips Cake. 10 499.00 4,990.00 515 Pcs Cupcake Molder Tray Of 6 12 Holes Baking Pan Muffin Cup Cake 10 89.00 890.00 516 Pcs Large Wooden Turner For Large Oven. Kitchen Turner Flat Spatula Scraper, Acacia Wood 10.5 Inches Long And 2.75 Inches Turner 3 200.00 600.00 517 Pcs Dressing Mirror (whole Body Mirror With 4 Wheels Height 5ft. Width 14 Inches) 1 1,500.00 1,500.00 518 Set Dish Towels (10 Pc. Per Set 25 Cm X 25 Cm Microfiber Super Absorbent) 5 993.00 4,965.00 519 Pcs Soap Dish (dual Soap Case With Cover & Handle- Bathroom Soap Dish / Soap Case) 50 70.00 3,500.00 520 Pcs Detergent (detergent Powder Set 6 Kilos-i Kilo X 6 Pouches) 50 288.00 14,400.00 521 Pcs Hand Soap (liquid Hand Soap Antibac 1 Gallon) 10 216.00 2,160.00 522 Pcs Pots (extra Size #4 (26cm Diameter 16 Cm In Height) 20 673.20 13,464.00 523 Pcs Pans (nonstick 12") 5 195.00 975.00 524 Pcs Toilet Paper Holder (wall Mounted Bathroom Toilet Paper Holder Tissue) 2 238.00 476.00 525 Pcs Dipper (plastic Dipper L 11" X W 36"x H 41" 5 100.00 500.00 526 Pcs Pail (utility Pail With Metal Handle 10l/26x27 Cm) 8 250.00 2,000.00 527 Pcs Trash Can (with Plastic Swing Lid L-27, W- 17., H- 40.5 Cm) 5 350.00 1,750.00 528 Pcs Toothbrush (extra Clean Toothbrush 5 Pk -soft) 20 182.40 3,648.00 529 Pcs Hairbrush (natural Wood Hairbrush Comb) 20 120.00 2,400.00 530 Pcs Comb (1 Dozen Suklay 3-hole X Sz-28 Big) 20 90.00 1,800.00 531 Pcs Toothpaste (red 100 Ml) 20 58.20 1,164.00 532 Pcs Plastic Tumbler 20 300.00 6,000.00 533 Pcs Razor (twin Blade Disposable Razors) 20 120.00 2,400.00 534 Pcs Nail Clipper (stainless Nail Clippers H-8 Cm Wt-0.046 Kg) 20 84.00 1,680.00 535 Pcs Nail File (12 Pcs Red Nail File (medium) 20 50.00 1,000.00 536 Pcs Deodorant (roll On 50 Ml Bottle) 20 150.00 3,000.00 537 Pcs Face Towel (basic Face Towel - Free Size) 20 110.00 2,200.00 538 Pcs Feminine Napkin (silk Floss 12 Pcs) 50 45.00 2,250.00 539 Pcs Dust Catcher With Broom (2n1 Broom Dustpan Set Windproof Floor Sweeper With Broom) 10 350.00 3,500.00 540 Pcs Feather Duster (soft Magic Feather Duster Long Size And Colorful Colors (plastic) 10 110.00 1,100.00 541 Pcs Wash Rags (round Rags) 10 30.00 300.00 542 Pcs Floor Mop (magic Spin Mop With Bucket 360° Rotating Floor Cleaning Plastic Liner) 10 900.00 9,000.00 543 Pcs Garbage Can (super Convenient Mini Flip Lid Trash Can (plastic) 10 150.00 1,500.00 544 Pcs Sponge (high Density Double-sided Dishwashing Sponge 7x10x3 Cm) 10 118.00 1,180.00 545 Pcs Spray Bottle (garden Sprayer Capacity: 500ml) 10 155.00 1,550.00 546 Pcs Table Napkin (1 Ply 40s Sheets Folded) 10 50.00 500.00 547 Pcs Place Mat (table Placemat Pvc Anti-slip Placemat Washable Durable Kitchen S:30x45cm) 10 50.00 500.00 548 Set Plates (12 Pcs Plates 8-inch Melamine White) 3 634.00 1,902.00 549 Set Drinking Glass (drinking Glass 10 Oz Tall Clear Tumblers Set Of 6 L=5.5cm H-12 Cm) 1 718.00 718.00 550 Pcs Pitcher (durable Crystal-clear Glass 1.5 L) 2 300.00 600.00 551 Pcs Bowl (serving Bowls, Clear Glass 20 Cm) 2 130.00 260.00 552 Pcs Water Pail (utility Pail With Metal Handle 10l Color: Red/ Blue L-27cm, W-27cm, H-26 Cm 4 350.00 1,400.00 553 Pcs Laundry Bar Soap (scrubber Bar 125g) 120 20.00 2,400.00 554 Pcs Clothesline (1 Pc Nonslip Clothesline 35 M) 20 140.00 2,800.00 555 Pcs Clothes Pin (laundry Clothes Pins Spring Clips 24 Pcs Plastic) 20 100.00 2,000.00 556 Pcs Wash Basin Plastic (laundry Basin 23 Inch) 5 250.00 1,250.00 557 Pcs Laundry Bag Set (4 Pcs/set Laundry Washing Bag- 1 Pc M(30cmx40cm) 1pc L (40cmx50cm) 1pc Xl (50x60 Cm) 10 200.00 2,000.00 558 Pcs Ironing Board (ironing Board With Stand Portable 36"iron Board (70cm To 86 Cm) 5 1,600.00 8,000.00 559 Pcs Flat Iron (non-stick Teflon Saleplate Spray Function Ht &width 251x170x120mm 5 1,000.00 5,000.00 560 Pcs Pants. Standard Slacks Medium Size 3 1,000.00 3,000.00 561 Pcs Polo. Public School Uniform Type. Medium Size 3 500.00 1,500.00 562 Pcs Blouse. Public School Uniform Type. Medium Size 3 500.00 1,500.00 563 Pcs Skirt. Commonly Used In Public School Type. Medium 3 600.00 1,800.00 564 Pcs Long Sleeves. Cotton, Medium Size 3 1,000.00 3,000.00 565 Pcs T-shirt With Collar. Cotton, Medium Size 3 800.00 2,400.00 566 Pcs T-shirt Without Collar. Cotton, Medium Size 3 500.00 1,500.00 567 Pcs Maong Pants. Medium Size, Female Cut, Medium 3 1,000.00 3,000.00 568 Pcs Maong Pants. Medium Size, Female Cut, Medium 3 1,000.00 3,000.00 569 Pcs Maleta. 7kg Hand Carry Luggage Travel Bag. 360 Universal Wheels. Divided Internal Space. 57 Liters Capacity. 40 X 57 X25 Cm Dimension. 3 1,500.00 4,500.00 570 Pcs Chef’s Hat. Chef Cap For Men Women Chef Head Cap Breathable Hat Fast Food Restaurant Coffee Shop Work Wear. Large Size. Black 20 250.00 5,000.00 571 Chef’s Hat. Chef Cap For Men Women Chef Head Cap Breathable Hat Fast Food Restaurant Coffee Shop Work Wear. Medium Size. White 20 250.00 5,000.00 572 Pcs Chef’s Hat. Chef Cap For Men Women Chef Head Cap Breathable Hat Fast Food Restaurant Coffee Shop Work Wear. Small Size. White 20 250.00 5,000.00 573 Pcs Chef’s Apron. Black Apron With 2 Large Pockets Adjustable Apron Halter Neck Unisex Dirt And Stain Resistant. Large 20 450.00 9,000.00 574 Pcs Chef’s Apron. Black Apron With 2 Large Pockets Adjustable Apron Halter Neck Unisex Dirt And Stain Resistant. Medium 20 450.00 9,000.00 575 Pcs Chef’s Apron. Black Apron With 2 Large Pockets Adjustable Apron Halter Neck Unisex Dirt And Stain Resistant. Small 20 450.00 9,000.00 576 Pcs Hair Net. Unisex Hair Net Cap Hair Mesh Weaving Wig Cap Hair Styling Tools Nylon Hair Nets Hollow Out High. Black 300 30.00 9,000.00 577 Dozen Hangers (12 Pcs. Plastic Hanger) 1 181.00 181.00 578 Pcs Wash Basin. Aluminum 32" Diameter. 6 1,500.00 9,000.00 579 Pcs Washing Machine. 7.0 Kg Digital Inverter Fully Automatic Top Load Washing Machine (water Level: 5, Gross Weight: 31kg, Net Weight: 27 Kg Gross Dimension: (wxhxd) 580x890x600mm Net Dimension: (wxhxd)= 540x857x568mm) 3 25,000.00 75,000.00 580 Pcs Vacuum Cleaner (heavy Duty Gas 12-25 Pl Wet And Dry Vacuum Cleaner/ Extractor With Power Socket System 1,250 W Weight-9kg, Max Input Power- 1,250 W, Max Vacuum Power-200 Mbar) 2 12,000.00 24,000.00 581 Pcs Socks (cotton Socks Unisex High Street Socks Sixe:38-44 5 200.00 1,000.00 582 Pcs Dress (sleeve Ruffle Hem Plain Elegant Red Small, Medium, Large) 3 500.00 1,500.00 583 Pcs Slippers (sizes 7-10, Flipflop Brand Light Weight And Durable 5 150.00 750.00 584 Pcs Mattress For Single Bed (30x75 Single Size Polyester 3.5 Inch Thick) 5 4,440.00 22,200.00 585 Pcs Pillows (foam Pillow 4x12"x20") 5 426.00 2,130.00 586 Pcs Bedsheets (cotton Full Garterize 3n1 Bed Sheets, For Single Bed Size) 5 1,100.00 5,500.00 587 Pcs Alarm Clock (stopwatch, Digital Timer) 5 850.00 4,250.00 588 Pcs Goalball, Standard Size And Weight, Blue 2 20,000.00 40,000.00 589 Pcs Basketball, Standard Size 2 2,000.00 4,000.00 590 Pcs Soccer Ball, Standard Size 2 1,500.00 3,000.00 591 Set Bocce Balls, 100mm Diameter, 4 Balls Colored Red, 4 Balls Colored Green, With Palena Ball Color White. Set With Bag. 2 20,000.00 40,000.00 592 Piece White Cane For Adults- Foldable Aluminum With White Anodized Finish And Plastic Tip. The Tube Has A Spring Lock Pin For Adjusting Handle Height From 58-94 Cm. 10 1,500.00 15,000.00 593 Piece White Cane For Kids- Foldable Aluminum With White Anodized Finish. The Tube Has A Spring Lock Pin For Adjusting Handle Height From 58-94 Cm. 10 1,150.00 11,500.00 594 Set Chess Board For Blind. Plastic Pieces With Special Markings, Board With Pattern To Distinguish White And Black Squares With Slots To Hold The Pieces. At Least 12"x24" Plastic Board. 4 5,000.00 20,000.00 595 Set Scrabble Board For Blind. Made Of Plastic With Special Markings On Tiles And Board. At Least 18"x18" Board. 5 4,000.00 20,000.00 596 Set Dolch Basic Sight Words. (bitay Max). Printed On White Tarpaulin 2 Ftx 3 Ft Binded With Two Wooden Sticks. With String (sabitan). Words At Least 2" Height Black, Arial Font Style. 5 1,500.00 7,500.00 597 Pcs Meter Stick, 100cm Stainless Steel Ruler 5 500.00 2,500.00 598 Box Braille Paper. White Fanfold Tractor-feed Braille Transcribing Paper: 8.5 X 11 Inches, 3-hole And 19-hole Punch. Dimensions:10.1 × 11.5 × 5.4 Inches. 1000 Sheets 7 10,000.00 70,000.00 599 Box Braille Paper. 11.5"x 8.5". 1000 Sheets 5 7,000.00 35,000.00 600 Box Swell-touch Paper 11 X 11.5-in- 100 Sheets 1 10,000.00 10,000.00 601 Unit Braille Machine, Standard. With Leather Cover. With Warranty On Parts. 2 49,500.00 99,000.00 602 Pcs Braille Slate. 27 Lines, 30 Cells Per Row, Black 25 1,000.00 25,000.00 603 Pcs Braille Contraction Pamphlet. Unified Contraction Pamphlet 4"x6". 25 600.00 15,000.00 604 Pcs Contraction Pamphlet. Nemeth Code. 4"x6". 25 600.00 15,000.00 605 Pcs Cranmer Abacus 25 650.00 16,250.00 606 Pcs Braille Stylus. Round Or Y Shape 25 200.00 5,000.00 607 Set Geometric Measurement. Set Of Protractor, Ruler And Triangles Made Of Plastic With Embossed Marking For The Blind, Standard Size. 24 1,000.00 24,000.00 Delivery Terms: Within 30 Days Drop Off Points: General Santos City Sped Integrated School – Quezon Avenue, Brgy. West, Gsc (ilrc) Payment Terms: Payment To The Service Provider Shall Be Made Through Philippine Veterans Bank Lddap-ada / Mds. In The Case Of Accounts Maintained In Other Bank, Bank Transfer Fees Shall Be Chargeable Against The Creditor’s Account. ***nothing Follows*** Grand Total 7,338,507.00 2. The Deped Now Invites A Bid For The Above Procurement Project. Bidders Must Have Completed, Within Three (3) Years From The Date Of Submission And Receipt Of Bids, A Contract Similar To The Project With An Amount Of At Least 50% Of The Abc To Be Bid For Non-expendable And 25% Of The Abc For Expendable. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, I.e., In Section Ii, Instructions To Bidders. Bids Received That Exceed The Abc Per Lot Shall Be Rejected At Bid Opening. The Department Of Education, Division Of General Santos City Division Through Its Bids And Awards Committee (bac) Now Invites Bids For The Herein-mentioned Goods. Delivery Of The Goods Is Required On The Expected Delivery Date(s) Stated Herein. 3. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using A Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) 9184, Otherwise Known As The “government Procurement Reform Act.” Bidding Is Restricted To Filipino Citizens/sole Proprietorships, Partnerships, Or Organizations With At Least Sixty Percent (60%) Interest Or Outstanding Capital Stock Belonging To Citizens Of The Philippines, And To Citizens Or Organizations Of A Country The Laws Or Regulations Of Which Grant Similar Rights Or Privileges To Filipino Citizens, Pursuant To Ra 5183. 4. A Complete Set Of Bidding Documents In Soft Copy Only May Be Purchased At Deped-division Of General Santos City Bac Secretariat, Located At Tiongson St., Lagao, General Santos City Upon Submission Of A Letter Of Intent, And Payment In Cash On A Non-refundable Fee By Interested Bidders To The Deped Division Cashier. Only Bidders Who Purchased The Bidding Documents Provided Below Shall Be Allowed To Submit Bid/bids Not Later Than The Scheduled Receipt And Opening Of Bids. Bidding Document Price Lot Number Price Lot No. 1 P 10,000.00 5. It May Be Viewed Or Downloaded After Payment From The Website Of The Philippine Government Electronic Procurement System (philgeps), Www.philgeps.gov.ph. The Schedule And Venue Of The Procuring Activities Are As Follows: Activity Date And Time Venue Pre-bid Conference February 19, 2025 2:00 P.m. (wednesday) Sds Conference And Online Via Google Meet Issuance Of Bidding Documents Until March 5, 2025 9:00 A.m (wednesday) To Be Sent To Bidder’s Email Address After Payment Of The Bidding Documents Receipt And Opening Of Bids March 5, 2025 10:00 A.m. (wednesday) Division Office/google Meet Prospective Bidders Are Strongly Encouraged To Order Or Download The Electronic Copy Of The Bidding Documents From The Philgeps Website: Www.philgeps.gov.ph, For Them To Be Included In The Document Request List Of The Project. The Pre-bid Conference Is Open To All Interested Parties Who May Have Or Have Not Bought The Bidding Documents. 6. Bids Must Be Physically Delivered To The Address And On The Date And Time Stated Herein. Submission Of Digital Copy Of The Bidding Documents Shall Not Be Accepted. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 18. A Valid Bid Securing Declaration Must Accompany The Bid(s) In Lieu Of Bid Security. Bids Will Be Opened In The Presence Of The Bidder’s Representatives Who Choose To Attend The Opening Of Bids At The Address, Date And Stated Herein. Late Bids Shall Not Be Accepted. 7. The Deped-division Of General Santos City Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Not Award The Contract(s), Or Annul The Bidding Process Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 8. For Further Information, Please Refer To: Ofelia S. Panes Michael Jhon A. Del Sol Administrative Officer Iv (records) Administrative Assistant Ii Bac Secretariat Head Bac Secretariat Member Email: Ofelia.panes@deped.gov.ph Email: Bac.depedgensan@deped.gov.ph Cell No. 09692673871 Cell No. 09278865516 Approved By: Mervie Y. Seblos, Cese Oic – Assistant Schools Division Superintendent Bac Chairperson Bacsec/mds

Details: Description Subject : Design And Build Of Dedvmh Nutrition And Dietetics Service Facilities Location : Dedvmh Compound, Bood, Ubay, Bohol Terms Of Reference I. Background Don Emilio Del Valle Memorial Hospital (dedvmh) Is A Licensed Level 2 General Hospital Located In Ubay, Bohol With 200 Authorized Bed Capacity Which Aims To Provide Highly Specialized Quality Healthcare Services To All Where Human Dignity Is Valued And Respected By Competent And Committed Personnel. In Accordance With The Provisions Of And Related Issuances Of Doh Administrative Order No. 2019-0056 Increasing The Bed Capacity Of Dedvmh From 50 Beds To 300 Beds And R.a. No. 11223, Or The “universal Health Care Act”, The Hospital Shall Provide Promotive, Preventive, Diagnostic, Curative, And Palliative Care Services, And Research, Professional Teaching And Training Programs And Shall Be Fully Equipped With The State-of-the Art Equipment And Facilities, Complemented By Adequately Trained And Competent Human Resources For Health Appropriate For A Licensed And Accredited Tertiary General Hospital. Dedvmh Shall Strengthen Its Existing Basic Services, And Aim For The Improvement Of Its Service Capability And Capacity Serving As Referral Hospital In The Northeastern Section Of The Bohol Province, Complementing Local Health Systems And Providers Of Municipalities In The Area. In Order To Fulfill This Mandate, Dedvmh Is Upgrading Its Services To Become A Level Iii Hospital To Provide Better And Quality Healthcare Services Especially In The Northeastern Part Of Bohol, Its Catchment Areas And Nearby Provinces. The Increase In The Bed Capacity And Expansion Of Services And Capability Are Consistent With The Dedvmh’s Hospital Development Plan (hdp) And Philippine Health Facility Development Plan (phfdp) 2020-2040. Ii. Objectives As Food Preparation Is Part Of The Critical Functions In Delivering Quality Healthcare Service, It Is Important That Its Site Be Given Adequate Repair And Renovation. The Objective Is To Repair And Expand The Existing Dietary Area Resulting To A More Spacious, Comfortable And Hygienic Station For Its End-users To Work Around. The Improvement Is Expected To Evoke A Less Stressful Environment And Increased Productivity Among Workers. The Design Must Also Conform To The Standards Of Set By In Accordance To The Manual On Technical Guidelines For Hospitals Planning And Design (level 3) And Doh Green And Safe Health Facilities Manual To Develop Climate Smart Health Facilities That Address And Adapt To The Impacts On The Environment. The Winning Bidder Shall Design For This Project With The Approval Of The Medical Center Including The Approved Detailed Estimates, Bill Of Quantities, Technical Specifications, And Methodology Of Construction And Scope Of Works Of The Project. Iii. Conceptual Design The Design Concept Of The Project Was Governed By The Planning And Design Standards Of Level 3 Service Capability Hospital Facility As Prescribed By The Latest Requirements Of The Department Of Health And Other Concerned Agencies. Building Design Shall Conform To The Provisions Of The National Building Code Of The Philippines (pd 1096), Accessibility Law (bp 344), Architecture Law (ra 9266), National Structural Code Of The Philippines, Electrical Engineering Law (ra 7920), Mechanical Engineering Law (ra 5336), Plumbing Code (ra 1378, 1993-1994 Revisions), Fire Code (ra 9514) And Other Laws And Regulations Covering Environmental Concerns And Local Ordinances And Regulations. The As-built Plan And Proposed Schematic Lay-out/call-out Will Be Provided As Basis Reference In The Development Of Preliminary Conceptual Design Plans To Be Submitted As Part Of The Technical Proposal. However, It Is The Responsibility Of The Bidder To Verify Actual Site Conditions And Dimensions. The Preliminary Conceptual Design Plans And Perspectives Shall Be Included Construed Part Of The Technical Proposal As Follows: Preliminary Conceptual Design Plans Required Specified Degree Of Details 1. Schematic Floor Plans: A. Ground Floor All Schematic Plans Shall Be At Least A3 Size Paper And Shall Meet The Minimum Space Requirements And Planning/design Guidelines Of Level 3 Hospital For: - Existing Dietary Complex Expansion And Improvement - Into Nutrition And Dietetics Service Facilities Preliminary Conceptual Design Plans Required Specified Degree Of Details A. Aerial Perspective View All Perspective / Plans Shall Be At Least A3 Size Paper In Colored Printed And Shall Conform With The Preliminary Conceptual Plans And At Least 3d Rendered. B. Man’s Eye / Worm’s Eye Perspective View All Perspective / Plans Shall Be At Least A3 Size Paper In Colored Printed And Shall Conform With The Preliminary Conceptual Plans And At Least 3d Rendered. C. Front Perspective View All Perspective / Plans Shall Be At Least A3 Size Paper In Colored Printed And Shall Conform With The Preliminary Conceptual Plans And At Least 3d Rendered. D. Rear Perspective View In Conformance With The Preliminary Conceptual Plans And At Least 3d Rendered. E. Left & Right-side Perspective View All Perspective / Plans Shall Be At Least A3 Size Paper In Colored Printed And Shall Conform With The Preliminary Conceptual Plans And At Least 3d Rendered F. Longitudinal And Transverse Section Plans At Least One Longitudinal And One Transverse Section Plans In At Least A3 Size Paper The Conceptualization Of The Design Including Its Specifications And Space Requirements Shall Complement And/or Supplement With The Existing Site Conditions And Specification Of The Existing Dietary Area At Ground Floor. Proponent’s Input, Suggestion And Recommendations With Regard To The Identification Of The Scope Or Physical Components And Structures, Specific Outputs And Requirements And Proposed Construction Methods Shall Be Considered. Iv. Performance Specifications And Parameters Site And Space Planning Were Governed By The Standards, Rules And Regulations On The Design Of Level 3 Hospitals As Prescribed By The Department Of Health And Other Concerned Agencies. Building Design Shall Conform To The Provisions Of The National Building Code Of The Philippines (pd 1096), Accessibility Law (bp 344), Architectural Law (ra 9266), Civil Engineering Law (ra 544), National Structural Code Of The Philippines, Electrical Engineering Law (ra 7920), Mechanical Engineering Law (ra5336), Plumbing Code (ra 1378, 1993-1994 Revisions), Fire Code (ra 9514) And Other Laws And Regulations Covering Environmental Concerns And Local Ordinances And Regulations. A. Pre-detailed Design 1. Engineering Surveys And Investigations 1.1 Surveys And Investigations Of The Site Includes Elevations And Contours (at 0.5m Interval), Soil Tests, Location, Dimension, Floor Elevations And Other Pertinent Data On Existing Buildings And Improvements (roads, Parking Areas, Mature Trees) And Existing Utility Lines (e.g. Water, Power, Telephone). 2. Preliminary Conceptual Design Plans/perspective 2.1 Preparation Of The Following Drawings For Design Development Based On The As Built Plan And Schematic Lay-out/call-out Prepared By The Procuring Entity. Please Refer To Section Iii. Conceptual Design. B. Detailed Design Preparation Of Final Design Concept And Detailed Architecture And Engineering Design Shall Be In Accordance With The Schematic Plans For Hospital Building And Design Conceptualization Duly Approved By The Dedvmh. In Determining The Final Design Concept And Detailed Architecture And Engineering Design, The Implementing Unit Together With The Design And Build Contractor Shall Initiate The Coordination Meeting With The Concerned Stakeholders In The Following Schedule: First Session - The Design And Build Contractor Shall Present The First Schematic Plan And Design Concept For Deliberation, Consultation And Inputs By The Proponents Within Ten (10) Calendar Days From The Effectivity Of Notice To Proceed Second Session - The Design And Build Contractor Shall Present The First Revision Of Schematic Plan And Design Concept For Deliberation, Consultation And Inputs By The Proponents, If There Any, Within Twenty (20) Calendar Days From The Effectivity Of Notice To Proceed Third Session - The Design And Build Contractor Shall Present The Second Revision Of Schematic Plan And Design Concept For Deliberation, Consultation And Inputs By The Proponents, If There Any, Within Thirty (30) Calendar Days From The Effectivity Of Notice To Proceed Upon Approval Of The Final Schematic Plan And Design Concept, The Design And Build Contractor Shall Then Proceed For The Design Phase, Enumerated As Follows: 1. Preparation Of The Following Detailed Design Drawings Of Entire Building (see Doh Checklist Of Drawings Requirements) Based On The Design Development Drawings And Design Parameters Including Any Revisions And Refinements As Approved And Required By The Dedvmh: A. Detailed Architectural Plans (refer To Checklist Of Drawings Requirements And Design Parameters). B. Detailed Structural Plans (refer To Checklist Of Drawings Requirements And Design Parameters). C. Detailed Electrical Plans (refer To Checklist Of Drawings Requirements And Design Parameters). D. Detailed Storm Drain, Sanitary And Plumbing Plans (refer To Checklist Of Drawings Requirements And Design Parameters). E. Detailed Mechanical Plans (refer To Checklist Of Drawings Requirements And Design Parameters). F. Structural Computations, Including Soil Boring Test Results And Seismic Analysis And Electrical Design Computations. G. General Notes And Technical Specifications Describing Type And Quality Of Materials And Equipment To Be Used, Manner Of Construction And The General Conditions Under Which The Project Is To Be Constructed. H. Detailed Cost Estimates, Detailed Bill Of Qualities, Bill Of Quantities, And Program Of Works Including A Summary Sheet Indicating The Unit Prices Of Construction Materials, Labor Rates And Equipment Rentals. I. Summary Of Works J. All Design Output Shall Include The Following: Particulars Design Required Output Hard Copy Printed In Standard Size Paper 40 X 30 Printed And Hardbound Catalog For All Perspective Views, Architectural Finishes, Electrical Fixtures, Sanitary/plumbing Fixtures Utilizing Standard A4 Size Photo Paper Electronic Copy Electronic Copies In Standard Formats: - Designplansfile.pdf; - Designplanscadfile.dwg; - Design3dfile.skp/dwg/etc; - Powerpointpresentation.ppt; - 3d Animations (walkthrough.mp4/avi/mov/etc.) Design And Build Contractor Shall Compile All The Files And To Be Stored In 1tb External Drive Fourth And Final Session - The Design And Build Contractor Shall Submit The Completed Detailed Design Drawings Of The Entire Building, Within Sixty (60) Calendar Days From The Effectivity Of Notice To Proceed. C. Green Building 1. Design Development Shall Consider At Least Basic Requirements For Green Building Applied To Hospital Facilities In Building Component Systems Such As Architectural, Structural, Electrical, Mechanical, And Sanitary. D. 3d Animation And Walkthrough Presentations Designer Shall Prepare A 3d Walkthrough, That Is, Taking A Virtual Tour Of The Proposed Project/structure In Any Design Platform. It Shall Be Produced From Digital 3d Models That Have Been Visualized To A Photo-realistic Standard That Will Showcase All The Design Elements, Both Externally And Internally Of A Property Development And Its Spaces. Minimum Expected Output Shall Include But Not Limited To: - 3d Walkthrough Presentation That Will Show From The Main Entrance Of The Hospital Compound, Going Through The Site Where The Project Is To Be Located. From The Site, It Should Walk Through The Main Facade And Entrance Of The Ground Floor Of The Building Up To The Third Floor Showing All The Respective Floors, Its Lobbies, Hallways, Rooms And Other Support Facilities. - In Addition, The 3d Walkthrough Presentation Shall Include The Exterior Views / Facade Of The Building With Its Adjoining Structures. E. Pre-construction Pre-construction Meeting Shall Be Scheduled On The Next Day That The Completed Detailed Design Drawings Are Submitted. Key Stakeholders—including The Dedvmh, And The Design And Build Contractor (architects, Engineers, Consultants, And Contractor—must Attend). The Meeting Will Serve To:  Review And Confirm The Submitted Design Documents.  Ensure That The Designs Comply With The Project’s Specifications, Budget, And Schedule.  Address Any Necessary Adjustments Or Clarifications Before Construction Commences. After The Pre-construction Meeting, The Design And Build Contractor Shall Finalize And Submit The Following Documents For The Approval Of Dedvmh: 1. Duly Signed Construction Schedule And S-curve 2. Duly Signed Manpower Schedule 3. Duly Signed Construction Methods 4. Duly Signed Pert Cpm And Ghannt Chart Showing Per Item Of Works Of Individual Projects 5. Log Book This Submission Should Encompass All Architectural, Structural, And Mepfs Plans, Specifications, And Any Amendments From The Meeting. These Documents Will Form The Basis For Construction. Upon The Dedvmh’s Approval Of The Submitted Construction Documents, A Notice To Commence Will Be Issued. Construction Activities May Only Begin Following The Issuance Of This Notice. F. Construction As A Rule, Contract Implementation Guidelines For Procurement Of Infrastructure Projects Shall Comply With Annex “e” And Guidelines For The Implementation Of Contracts For Design And Build Infrastructure Projects Shall Comply With Annex “g” Of Irr, Ra 9184. The Following Provisions Shall Supplement These Procedures: 1. Scope Of Works: Supply Of Materials, Labor, Tools And Equipment Necessary To Complete The Execution Of Architectural, Structural And Electrical And Mechanical Works. Includes All Other Necessary Works That Complete For The Fully Operational Building But Limited To The Following Work Items; A) Site Works - Provision Of Temporary Perimeter Fence - Demolition Of Existing Building/structure, Includes Hauling Of Debris Within The Hospital Compound - All Materials, Debris, Etc. Identified As Garbage As Directed By Hospital Management Shall Be Disposed Off-site - Excavation And Grading Provide Necessary Soil Protection On Excavated Portion. - Soil Poisoning And Termite Control B) Foundation Works - Foundation Of The Entire Building Includes Column Footings, Wall Footings And Other Sub-structures As Specified In The Approved Plan. C) Concrete Works - From New Foundation; Includes Slabs, Beams And Girders D) Architectural Works I) Exterior Walls – All Exterior Wall At Ground Floor Ii) Interior Walls – All Interior Wall At Functional Floors Complete With Wall Finishes Iii) Ceiling Works – All Functional Floors As Determined By Procuring Entity Iv) Floor Finish – All Functional Floors As Determined By Procuring Entity V) Doors And Windows– All Exterior Doors And Windows As Per Plan And Specifications Vi) Doors And Windows – All Functional Areas As Determined By Procuring Entity Vii) Painting Works – All Exterior Walls; Interior Walls At Functional Areas Viii) Façade And Signage E) Electrical Works I) Roughing-ins – All Necessary Roughing-ins Including Riser Conduits Including Ii) Cable Tray Iii) Panel Boards And Breakers – Main Breaker; Panel Boards From Ground Floor To Third Floor Iv) Wires And Cables – All Wires And Cables At Functional Floors Includes Installation Of Main Feeder Lines Tap To Existing Power House Including Connections To All Panel Board And Breakers V) Electrical Fixtures And Devices – All Fixtures And Wiring Devices At Functional Areas. Provision Of Usb Ready Outlets To Every Rooms. Vi) Application Of Electrical Connections/permits Shall Be Shouldered By The Contractor F) Mechanical Works I) Installation Of Automatic Fire Protection System At Functional Areas Ii) Installation Air Condition Units At Functional Areas As Determined By Professional Mechanical Engineer G) Plumbing And Sanitary Works I) Installation Of Plumbing And Sanitary System At Functional Areas, Includes; - Water Supply Pipelines - Waste Water Pipelines - Plumbing Fixtures And Accessories - Necessary Riser Pipes - Fiber Glass Pressure Tank - Provision Of Water Softener I) Electronics / Auxiliary Works - At Functional Areas: Public Address / Voice Evacuation Systems (paging Systems), Cctv, And Or Integrated Information And Communication Systems, Installation Of Fire Detection And Alarm System (fdas) At Functional Floors J) Other Works - At Dietary: Lpg Pipelines 1. No Works Shall Commence Unless The Contractor Has Submitted The Prescribed Documentary Requirements And The Dedvmh Has Given Written Approval. Work Execution Shall Be In Accordance With Reviewed And Approved Documents. The Contractor Shall Process The Approval Of Permit To Construct (ptc) Form Doh – Central Visayas Regional Office, Cebu City. In Addition To, The Contractor Shall Process The All-necessary Permits (i.e., Building Permit, Occupancy Permit And All Prerequisite Permits) Chargeable Against The Project. 2. The Contractor Shall Be Responsible For Obtaining All Necessary Information As To Risks, Contingencies And Other Circumstances Which May Affect The Works And Shall Prepare And Submit All Necessary Documents Specified By The Concerned Building Officials To Meet All Regulatory Approvals As Specified In The Contract Documents. 3. Any Errors, Omissions, Inconsistencies, Inadequacies Or Failure Submitted By The Contractor That Do Not Comply With The Requirements Shall Be Rectified, Resubmitted And Reviewed At The Contractor’s Cost. If The Contractor Wishes To Modify And Design Or Document Which Has Been Previously Submitted, Reviewed And Approved, The Contractor Shall Notify The Hospital Management And The Procuring Entity Within A Reasonable Period Of Time And Shall Shoulder The Cost Of Such Changes. 4. As A Rule, Changes In Design And Construction Requirements Shall Be Limited Only To Those That Have Not Been Anticipated In The Contract Documents Prior To Contract Signing And Approval. The Following Guidelines Shall Govern Approval For Change Or Variation Orders: A. Change Orders Resulting From Design Errors, Omissions Or Non-conformance With The Performance Specifications And Parameters And The Contract Documents By The Contractor Shall Be Implemented By The Contractor At No Additional Cost To The Procuring Entity. B. Provided That The Contractor Suffers Delay And/or Incurs Costs Due To Changes Or Errors In The Dedvmh Performance Specifications And Parameters, The Contractor Shall Be Entitled To Either One Of The Following: 1. An Extension Of Time For Any Such Delays Under Section 10 Of Annex “e” Of Irr (ra 9184); Or 2. Payment For Such Costs As Specified In The Contract Documents, Provided, That The Cumulative Amount Of The Variation Order Does Not Exceed Ten Percent (10%) Of The Original Project Cost. C. The Contract Documents Shall Include The Manner And Schedule Of Payment Specifying The Estimated Contract Amount And Installments In Which The Contract Will Be Paid. D. The Contractor Shall Be Entitled To Advance Payment Subject To The Provisions Of Section 4 Of Annex “e”, Irr (ra 9184). B. The Dedvmh Shall Define The Quality Control Procedures For The Design And Construction In Accordance With The Doh Guidelines And Shall Issue The Proper Certificates Of Acceptance For Sections Of The Works Or Whole Of The Works As Provided For In The Contract Documents. C. The Contractor Shall Provide All Necessary Equipment, Personnel, Instruments, Documents And Others To Carry Out Specified Tests. D. This Design And Build Projects Shall Have A Minimum Defects Liability Period Of One (1) Year After Contract Completion Or As Provided For In The Contract Documents. This Is Without Prejudice To The Liabilities Imposed Upon The Engineer/architect Who Drew Up The Plans And Specification For Building Sanctioned Under Section 1723 Of The New Civil Code Of The Philippines. E. The Contractor Shall Be Held Liable For Design And Structural Defects And/or Failure Of The Completed Project Within The Warranty Period Of 15 Years For Permanent Structures/buildings As Specified In Section 62.2.3.2 Of The Irr (ra 9184) V. Implementation Arrangement A. Reporting Protocol Contact Person I. Nelson A. Elle, Md, Dtmph, Mscih Office Of The Medical Center Chief Ii Don Emilio Del Valle Memorial Hospital Bood, Ubay, Bohol Ii. Joan V. Kadusale, Cpa Supervising Administrative Officer Don Emilio Del Valle Memorial Hospital Bood, Ubay, Bohol Iii. Leomel R. Labitad, Ce Engineer Iii Don Emilio Del Valle Memorial Hospital Bood, Ubay, Bohol Iv. Allana Jane C. Dacoylo, Uap Architect Ii Don Emilio Del Valle Memorial Hospital Bood, Ubay, Bohol Vi. Elegibility Requirements A. Basic 1. The Eligibility Requirements For Design And Build Scheme Shall Comply With The Applicable Provisions Of Sections 23-24 Of Irr Of Ra 9184. 2. A Modified Set Of Requirements Integrating Eligibility Documents And Criteria For Infrastructure Project And Consulting Services Shall Be Adopted In Accordance With Annex G - Guidelines For The Procurement And Implementation Of Contracts For Design And Build Infrastructure Projects Of Irr Of Ra 9184. 3. Pcab Classification Under “general Building”; License Category B “medium A” 4. Contractor Must Have Similar Project In The Amount At Least Fifty Percent (50%) Of The Abc Within The Past Five (5) Years. 5. Similar Projects With The Following But Not Limited To:  Low-rise Hospital Facility Project, Must Have Ongoing Or Completed Project At Least 2-storey Building.  Supply And Installation Of Hvac System. B. Specialized 1. For Pre-design And Design Phase Of The Contract, The Bidder Shall Comply The Following Professionals To Be Assigned: I. Project Coordinator • Licensed Architect Or Engineer With At Least 10 Years’ Experience In Hospital-related Project Management. • Superb Oral And Written Communication Skills, Organization Skills And Excellent Administrative Abilities. Ii. Architect • The Architect Must Be A Registered And Licensed Architects (rla), With An Updated Professional Identification Card And Must Be A Member In Good Standing Of The Integrated And Accredited Professional Organization Of Architects (iapoa). • Should Have At Least 5 Years’ Experience In Hospital-related Project. Iii. Structural Engineer • Licensed Structural Engineer With At Least 5 Years’ Experience In Hospital-related Project Management. • Must Be A Member Of Accredited Structural Engineer Associations. Iv. Mechanical Engineer • Licensed Professional Mechanical Engineer With At Least 5 Years’ Experience In Hospital-related Project. V. Electrical Engineer • Licensed Professional Electrical Engineer With At Least 5 Years’ Experience In Hospital-related Project. Vi. Sanitary Engineer • Licensed Sanitary Engineer With At Least 5 Years’ Experience In Hospital-related Project. Vii. Cad Operator (at Least One For Architecture And One For Each Engineering Specialty) • At Least Bachelor’s Degree In Architecture, Engineering, And/or Industrial Technology Major In Drafting • Proficient In Autocad Software Viii. Administrative Support Staff 2. For The Construction Phase Of The Contract, The Contractor Shall Assign Technical Personnel With The Following Qualification: I. Project Manager • Licensed Architect Or Engineer With At Least 10 Years’ Experience In Medium Rise Hospital-related Project • Superb Oral And Written Communication Skills, Organization Skills And Excellent Administrative Abilities. Ii. Project Engineer (civil) • Licensed Civil Engineer With At Least 5 Years’ Experience As Project Engineer In Medium Rise Hospital-related Project Iii. Project Engineer (mechanical) • Registered Mechanical Engineer With At Least 5 Years’ Experience As Project Engineer In Medium Rise Hospital-related Project Iv. Project Engineer (electrical) • Registered Electrical Engineer With At Least 5 Years’ Experience As Project Engineer In Medium Rise Hospital-related Project V. Cad Operator (at Least One For Architecture And One For Each Engineering Specialty) • At Least Bachelor’s Degree In Architecture, Engineering, And/or Industrial Technology Major In Drafting • Proficient In Autocad Software Vi. General Foreman (all Discipline) • With At Least 5 Years’ Experience As General Foreman In Medium Rise Project Vii. Skilled Workers (all Discipline) • With At Least 3 Years’ Experience In Medium Rise Project Viii. Administrative Support Staff Vii. Approved Budget Cost Project Description Approved Budget Cost Design Of Dedvmh Nutrition And Dietetics Service Facilities 5%-6% Of Abc Construction Of Dedvmh Nutrition And Dietetics Service Facilities 94%-95% Of Abc Total Abc Php 15,000,000.00 The Approved Budget For The Design-build Contract Is Fifteen Million Pesos (php 15,000,000.00) Which Is Identified As The Design And Build Of Don Emilio Del Valle Memorial Hospital Nutrition And Dietetics Service Facilities. Detailed Architectural And Engineering Design Services Shall Not Seven Percent (7%) Of The Approved Budget Cost (as Per Prboa Resolution No. 6 Series Of 2016 - Architect’s Guidelines For Standards Of Professional Practice Compliances On The Methods Of Compensation And Schedule Of Fees, Pursuant To Republic Act No.9266, Published In The Official Gazette, September 19, 2016 Issue) Of The Entire Building Inclusive Of Taxes And Duties. Proposals Exceeding The Approved Budget Shall Be Automatically Rejected. Viii. Estimated Duration Of Engagement The Duration Of The Contract Is Three Hundred Sixty (240) Calendar Days From The Design Phase Up To The Completion Of The Project From The Date Of Effectivity: I. Pre-design And Design Phase - 60 Calendar Days Ii. Construction Phase - 180 Calendar Days Ix. Minimum Requirements For Construction Safety And Health A. General Requirements No Contractor Or Subcontractor Shall Require Any Employee To Work In Surroundings Or Under Working Conditions That Are Unsanitary, Hazardous, Or Dangerous To His Health Or Safety. In Order To Meet This General Requirement, The Contractor Must: 1. Initiate And Maintain Programs (written Or Otherwise) To Comply With This General Requirement. 2. Provide Frequent And Regular Inspections Of The Job Sites By Competent Persons.  Competent Person Means One Who Is Capable Of Identifying Existing And Predictable Hazards In The Surroundings Or Working Conditions Which Are Unsanitary, Hazardous, Or Dangerous To Employees, And Who Has Authorization To Prompt Corrective Measures To Eliminate Them. 3. Prohibit The Use Of Any Machinery, Tool, Material, Or Equipment That Is Not In Compliance With Applicable Requirements. 4. Permit Only Those Employees Adequately Trained To Operate Machinery Or Equipment. 5. Provide Training For All Employees In:  Recognition And Avoidance Of Unsafe Conditions  Workplace Safety And Health Requirements  Applicable Hazards, Safe Handling, And Personal Protective Equipment Necessary For Handling Poisons, Caustics, Flammables, And Other Harmful Substances Relevant To Their Job Duties.  Specific Hazards And Procedures For Entering Confined Spaces If Applicable 6. Provide Provisions For Medical Care And First Aid. 7. Develop An Effective Fire Protection And Prevention Plan. 8. Ensure Appropriate Housekeeping Measures Including Clear Walkways And Removal Of Combustible Scrap And Debris. 9. Require The Wearing Of Appropriate Personal Protective Equipment Such As Hard Hats, Safety Glasses, Steel Toe Shoes, Or Other Appropriate Protective Equipment In All Operations Where There Is An Exposure To Hazardous Conditions. 10. Develop An Emergency Action Plan Covering Designated Actions Employers And Employees Must Take To Ensure Employees Safety From Fire And Other Emergency.  Plan Must Be In Writing For Employers With Greater Than 10 Employees  All Employees Must Be Trained Upon Initial Assignment On The Parts Of The Plan The Employee Needs To Know In The Event Of An Emergency. 11. Provide Access To Hand Washing Facilities, Toilets, And An Adequate Supply Of Drinking Water. 12. Provide Safety And Health Signs That Are Clearly Visible To Construction Workers And Public. 13. Conduct Regular Safety Meetings. Source: Colorado State University Occupational Health And Safety Section Department Of Environmental Health Fort Collins, Colorado X. Design Technical Specifications And Requirements The Bidder Shall Submit The Following Design Deliverables In Accordance With The Design Specifications, Parameters And Drawing Checklist But Not Limited To The Following: Activity Reports And Documents Required 1. Pre-design Phase 1.1 Master Site Development Plans And Conceptual 3d Design Five (5) Sets Duly Signed And Seal Master Site Development Plans In Hard Copy (at Least 20 X 30 Paper Size In Desired Minimum Scale) And Softcopy (editable File.dwg And 3d Model.skp/cad/etc) Powerpoint Presentation And/or Walkthrough Presentation 2. Design Phase 2.1 Detailed Architecture And Engineering Designs/plans Including Applicable And/or Approved Revisions To The Satisfaction Of The Procuring Entity Five (5) Sets Duly Signed And Seal Detailed Architecture And Engineering Plans/drawing In Hard Copy (at Least 20 X 30 Paper Size In Desired Minimum Scale) And Softcopy (editable File.dwg And 3d Model.skp/cad/etc) (refer To Design Parameters And Drawing Checklists) 2.2 Construction Technical Specifications Five (5) Sets Duly Signed And Seal Construction Technical Specifications In Hard Bound Xi. Space Requirements General Floors:  Ceiling Height Should Be At Least Three Meters Clear Height For 2nd Floor And Up. Ground Floor Lobby Must Be Of Higher Ceiling.  Provision Of Utility Room Enough To House Trolley And Dirty Utilities With Floor Drain  All Floors Shall Have Direct Access To Ramp  Both Stairs Are For Service And Emergency Use  External Window At Second Floor And Up Shall Be Of Awning Type.  Provision Of Electrical Room  Ramp For Wheelchair Access (with A Clear Width Of At Least 1.22 M. 4 Ft.).  Minimum Of Two (2) Exits, Remote From Each Other, For Each Floor Of The Building.  Exits Restricted To The Following Types: Door Leading Directly Outside The Building, Interior Stair, Ramp And Exterior Stair.  Exits Terminate Directly At Open Space To The Outside Of The Building. Ground Floor – Nutrition And Dietetics Service Facilities • Hospital Staff Dining Room - This Area Is Where Hospital Staff Diners Take Their Meals. - Planning Relationships: A. Close To Serving And Food Assembly Area B. Close To Dishwashing Area - Lighting System: C. For General Illumination, Provide At Least 250 Lux. - Power System: D. Provide At Least Four (4) Units Of Outlet With Specifications Of 15a, 2p, 240v, Duplex, Grounding Type And Universal Slots. Also, Provide At Least One (1) Unit Of Outlet For Emergency Light With Specifications Of 15a, 2p, And 240v, Single. - Auxiliary System: E. Provide And Install The Following Auxiliary System: • Communication System  Telephone System – Provide At Least One (1) Unit Telephone Outlet.  Local Area Network System – Provide At Least One (1) Unit Data Outlet.  Public Address Paging System – Provide At Least One (1) Unit Paging System - Fire Alarm System: F. Provide At Least Two (2) Units Smoke Detector. - Air Conditioning System: G. Provide Air Conditioning System. • Cooking And Baking Area - This Area Is Dedicated For Cooking And Baking Food, With High Pressure Gas Piping System. Equipment And Accessory Checklist: • Hood, Exhaust • Drainage Key Furniture/fixture Checklist: • Counter, 900mm High • Stainless Steel Grade 304 Sink, Single Compartment With Drainboard; 350-400mm Deep • Stainless Steel Grade 304 Sink, Double Compartment With Drainboard; 350-400mm Deep • Shelves, Overhead • Drain, Trench Grating • Concealed Floor Drain - Planning Relationships: A. Adjacent To Staff Dining Room B. Close To Dietitian’s Office - Lighting System: C. For General Illumination, Provide At Least 500 Lux. - Power System: D. Provide At Least Thirteen (13) Units Of Outlet With Specifications Of 15a, 2p, 240v, Duplex, Grounding Type And Universal Slots. Provide At Least Two (2) Units Ground Fault Circuit Interrupter. Also, Provide At Least One (1) Unit Of Outlet For Emergency Light And Two (2) Units For Exhaust Fan With Specifications Of 15a, 2p, And 240v, Single. - Standby/emergency System: E. Provide And Install Adequate Life Safety And Critical Emergency Branch Circuit For Lighting And Utilization Equipment Connected To The Alternate Power Source. - Auxiliary System: F. Provide And Install The Following Auxiliary System: • Communication System  Public Address Paging System – Provide At Least One (1) Unit Paging System - Fire Alarm System: G. Provide At Least Three (3) Units Smoke Detector. - Gas Piping System: H. Provide High Pressure Gas Piping System. - Equipment And Accessories: I. Provide Hood, Exhaust J. Provide Range With Oven K. Provide Range With Broiler - Air Conditioning System: L. Provide Air Conditioning System. • Food Preparation Area W/ Special Diet Preparation Area - This Area Is Where Food Service Workers Prepare Food Vegetables, Slice And Cut Meat And Fish, Segregate Food, Set-up And Assemble Cooked Food, Place Food Trays And Containers On Food Conveyors To Be Taken To Wards. This Is Also Where Dietitian Puts Tags On Prepared Trays For Pay Patients. This Also Includes Space For Special Diet Preparation Area Key Furniture/fixture Checklist: • Counter, Work; Stainless Steel Grade 304 • Stainless Steel Grade 304 Sink, Single Compartment, With Drainboard; 350-400mm Deep • Stainless Steel Grade 304 Sink, Double Compartment, With Drainboard; 350-400mm Deep • Counter, Food Preparation; Stainless Steel Grade 304 • Counter, Tray Set-up; Stainless Steel Grade 304 • Shelves, Overhead • Drain, Trench Grating; Stainless Steel - Planning Relationships: A. Adjacent To Staff Dining B. Close To Dietitian’s Office - Lighting System: C. For General Illumination, Provide At Least 500 Lux. - Power System: D. Provide At Least Seven (7) Units Of Outlet With Specifications Of 15a, 2p, 240v, Duplex, Grounding Type And Universal Slots. Provide At Least One (1) Unit Ground Fault Circuit Interrupter Also, Provide At Least One (1) Unit Of Outlet For Emergency Light With Specifications Of 15a, 2p, And 240v, Single. - Auxiliary System: E. Provide And Install The Following Auxiliary System: • Communication System  Telephone System – Provide At Least One (1) Unit Telephone Outlet.  Local Area Network System – Provide At Least One (1) Unit Data Outlet.  Public Address Paging System – Provide At Least One (1) Unit Paging System - Fire Alarm System: F. Provide At Least One (1) Unit Smoke Detector. - Air Conditioning System: G. Provide Air Conditioning System. • Blenderized And Tube Feeding Area - This Area Is Where Preparation Of Food And Equipment Needed For Blenderized And Tube Feeding. Key Furniture/fixture Checklist: • Counter, Work; Stainless Steel Grade 304, With Cabinets Above And Shelves Below • Stainless Steel Grade 304 Sink, Single Compartment, With Drainboard; 350-400mm Deep • Stool, Adjustable Height • Concealed Floor Drain - Planning Relationships: A. Adjacent To Special Diet Preparation Area B. Close To Dietitian/nutritionist’s Office - Lighting System: C. For General Illumination, Provide At Least 250 Lux. - Power System: D. Provide At Least Three (3) Units Of Outlet With Specifications Of 15a, 2p, 240v, Duplex, Grounding Type And Universal Slots. Provide At Least Three (3) Units Ground Fault Circuit Interrupter Also, Provide At Least One (1) Unit Of Outlet For Emergency Light With Specifications Of 15a, 2p, And 240v, Single. - Fire Alarm System: E. Provide At Least One (1) Unit Smoke Detector (ionization Type). - Air Conditioning System: F. Provide Air Conditioning System. • Serving And Food Assembly Area - This Area Is Where Food Service Workers Set Up And Assemble Cooked Food, And Place Food Trays And Containers On Food Conveyors To Be Taken To Wards. Key Furniture/fixture Checklist: • Counter, Work; Stainless Steel Grade 304 • Stainless Steel Grade 304 Sink, Single Compartment, With Drainboard; 350-400mm Deep • Stool, Adjustable Height • Concealed Floor Drain - Planning Relationships: A. Adjacent To Staff Dining Room B. Close To Dietitian/nutritionist’s Office - Lighting System: C. For General Illumination, Provide At Least 500 Lux. - Power System: D. Provide At Least One (1) Unit Of Outlet With Specifications Of 15a, 2p, 240v, Duplex, Grounding Type And Universal Slots. Provide At Least One (1) Unit Ground Fault Circuit Interrupter Also, Provide At Least One (1) Unit Of Outlet For Emergency Light With Specifications Of 15a, 2p, And 240v, Single. - Fire Alarm System: E. Provide At Least One (1) Unit Smoke Detector (ionization Type). - Air Conditioning System: F. Provide Air Conditioning System. • Food Conveyor Parking - This Space Is For Transit Station For Food Tray Truck/conveyor. - Planning Relationships: A. Close To Dishwashing Area B. Adjacent To Food Assembly/tray Set-up Area - Lighting System: C. For General Illumination, Provide At Least 250 Lux. - Power System: D. Provide At Least One (1) Unit Of Outlet With Specifications Of 15a, 2p, 240v, Duplex, Grounding Type And Universal Slots. Provide At Least One (1) Unit Ground Fault Circuit Interrupter Also, Provide At Least One (1) Unit Of Outlet For Emergency Light With Specifications Of 15a, 2p, And 240v, Single. - Fire Alarm System: E. Provide At Least One (1) Unit Smoke Detector (ionization Type). - Ventilation System: F. Provide One (1) Unit Orbit Fan. • Cold Storage - This Area Is For Storage Of Poultry, Meat And Dairy Products Procured, Food That Easily Spoils (egg, Vegetables, Fruits), And Of Leftover Cooked Food That Are Still Edible Equipment And Accessory Checklist: • Refrigerator, 20 Cu. Ft. • Freezer, 20 Cu. Ft. • Chiller, 20 Cu. Ft., Reach-in Key Furniture/fixture Checklist: • Table; Stainless Steel Grade 304; 750 X 1200mm • Concealed Floor Drain - Planning Relationships: A. Adjacent To Dry Storage Room B. Close To Receiving Area C. Adjacent To Dietitian’s Office - Lighting System: D. For General Illumination, Provide At Least 150 Lux. - Power System: E. Provide At Least Ten (10) Units Of Outlet With Specifications Of 15a, 2p, 240v, Duplex, Grounding Type And Universal Slots. Provide At Least One (1) Unit Ground Fault Circuit Interrupter Also, Provide At Least One (1) Unit Of Outlet For Emergency Light With Specifications Of 15a, 2p, And 240v, Single. - Fire Alarm System: F. Provide At Least One (1) Unit Smoke Detector (ionization Type). - Ventilation System: G. Provide One (1) Unit Exhaust Fan. • Dry Storage - This Area Is For Storage Of Food Procured, Food Intended For The Next Two Meals, Of Excess Supplies For Future Use, And Of Food That Does Not Spoil Easily. Key Furniture/fixture Checklist: • Counter, Work • Shelves, 400 Mm Deep • Cabinet, Lockable - Planning Relationships: A. Adjacent To Cold Storage Room - Lighting System: B. For General Illumination, Provide At Least 150 Lux. - Power System: C. Provide At Least Three (3) Unit Of Outlet With Specifications Of 15a, 2p, 240v, Duplex, Grounding Type And Parallel Slots. Provide At Least One (1) Unit Ground Fault Circuit Interrupter Also, Provide At Least One (1) Unit Of Outlet For Emergency Light With Specifications Of 15a, 2p, And 240v, Single. - Fire Alarm System: D. Provide At Least One (1) Unit Smoke Detector (ionization Type). - Ventilation System: E. Provide One (1) Unit Orbit Fan. • Storage For Utensils/silverware - This Area Is For Storage Of Kitchen Utensils And Silverware Key Furniture/fixture Checklist: • Shelves, Open, 600mm Deep - Planning Relationships: A. Close To Dietitian’s Office - Lighting System: B. For General Illumination, Provide At Least 150 Lux. - Power System: C. Provide At Least Two (2) Unit Of Outlet With Specifications Of 15a, 2p, 240v, Duplex, Grounding Type And Universal Slots. Provide At Least One (1) Unit Ground Fault Circuit Interrupter Also, Provide At Least One (1) Unit Of Outlet For Emergency Light With Specifications Of 15a, 2p, And 240v, Single. - Ventilation System: D. Provide One (1) Unit Orbit Fan. • Delivery Receiving Area - This Area With Exhaust Fan Is Dedicated For Dietitian On Duty And Auditor Witness Weighing Of Food Delivered By Supplier, And Where Auditor Inspects And Checks Quality Of Food Items Purchased From The Market And Those Delivered By The Supplier. Key Furniture/fixture Checklist: • Counter, Stainless Steel • Sink, Single Compartment With Drainboard; 350-400mm Deep • Counter, Tiled • Shelves, Open • Concealed Floor Drain - Planning Relationships: A. Adjacent To Dietitian’s Office B. Close To Cold And Dry Storage Rooms - Lighting System: C. For General Illumination, Provide At Least 150 Lux. - Power System: D. Provide At Least One (1) Unit Of Outlet With Specifications Of 15a, 2p, 240v, Duplex, Grounding Type And Universal Slots. Also, Provide At Least One (1) Unit Of Outlet For Emergency Light With Specifications Of 15a, 2p, And 240v, Single. - Ventilation System: E. Provide At Least One (1) Unit Orbit Fan. • Dishwashing And Pots Washing Area - This Area Is For Washing Of Pots, Pans, Trays, Dishes And Other Kitchen Utensils, And Where Food Service Workers Perform Other Clean-up Activities. Equipment And Accessory Checklist: • Dishwashing Machine, Floor Unit • Wash Container, 380 Mm Dia. • Waste Bin With Black Lining Key Furniture/fixture Checklist: • Counter, Stainless Steel Grade 304 • Stainless Steel Sink Grade 304, Double Compartment With Drainboard • Grease Trap • Counter, With Upturned Edge • Shelves, Open • Table, Feeder, Stainless Steel 700 X 1200mm • Table, Work, Stainless Steel 700 X 2400mm • Concealed Floor Drain - Planning Relationships: A. Close To Food Preparation Area B. Close To Dietitian’s Office - Lighting System: C. For General Illumination, Provide At Least 250 Lux. - Power System: D. Provide At Least Six (6) Units Of Outlet With Specifications Of 15a, 2p, 240v, Duplex, Grounding Type And Parallel Slots. Provide At Least One (1) Unit Ground Fault Circuit Interrupter Also, Provide At Least One (1) Unit Of Outlet For Emergency Light With Specifications Of 15a, 2p, And 240v, Single. - Fire Alarm System: E. Provide At Least One (1) Unit Smoke Detector (ionization Type). - Ventilation System: F. Provide At Least Two (2) Units Orbit Fan. • Waste Holding Area - This Area Is For Food Service Workers Sort Garbage Accordingly, Pack Garbage And/or Place Sorted Garbage Into Proper Bins/container, And Where Garbage Generated For A Day Or Two Is Temporarily Stationed Prior To Being Collected For Transfer To The Waste Management Service. Equipment And Accessory Checklist: • Garbage Bin Containers • Faucet With Hose Bibb Key Furniture/fixture Checklist: • Floor Drain - Planning Relationships: A. Located In The Perimeter Of The Dietetics Area - Lighting System: B. For General Illumination, Provide At Least 150 Lux. - Power System: C. Provide At Least One (1) Unit Ground Fault Circuit Interrupter (gfci). Also, Provide At Least One (1) Unit Of Outlet For Emergency Light With Specifications Of 15a, 2p, And 240v, Single. - Fire Alarm System: D. Provide At Least One (1) Unit Smoke Detector (ionization Type). - Ventilation System: E. Provide At Least One (1) Unit Orbit Fan. • Dietitian’s Office / Staff Office - This Room Area Is Where The Chief Dietitian Calls Meetings With Staff For The Preparation Of Monthly Menu, Where Chief Dietitian And Staffs Reads, Writes And Uses Telephone In His Work Station, Dietitian And Staff Receive Visitors, Dietitian And Staff Store, File And Retrieves Records. - Planning Relationships: A. Located In The Kitchen Where It Shall Give The Dietitian Extensive/elevated View Of Work Areas And Control Over Possible Pilferage Of Dietary Supplies And Equipment. - Lighting System: B. For General Illumination, Provide At Least 500 Lux. - Power System: C. Provide At Least Twelve (12) Units Of Outlet With Specifications Of 15a, 2p, 240v, Duplex, Grounding Type And Universal Slots. Provide At Least One (1) Unit Ground Fault Circuit Interrupter Also, Provide At Least One (1) Unit Of Outlet For Emergency Light With Specifications Of 15a, 2p, And 240v, Single. - Auxiliary System: D. Provide And Install The Following Auxiliary System: • Communication System  Telephone System – Provide At Least One (1) Unit Telephone Outlet.  Local Area Network System – Provide At Least One (1) Unit Data Outlet.  Public Address Paging System – Provide At Least One (1) Unit Paging System - Fire Alarm System: E. Provide At Least Two (2) Units Smoke Detector (ionization Type). - Air Conditioning System: F. Provide Air Conditioning System • Staff’s Dressing, Lockers, Toilet And Bath - This Room/space Is Equipped With Secure Lockers, Private Dressing Rooms, And Accessible Toilets And Showers To Support Hygiene And Comfort For Male And Female Staff. This Space, With Its Own Separate Staff Entrance, Allows For Efficient Staff Flow. - Planning Relationships: A. Close To Dishwashing Area B. Adjacent To Food Assembly/tray Set-up Area - Lighting System: C. For General Illumination, Provide At Least 150 Lux. - Power System: D. Provide At Least One (1) Unit Of Outlet With Specifications Of 15a, 2p, 240v, Duplex, Grounding Type And Universal Slots. Also, Provide At Least One (1) Unit Of Outlet For Emergency Light With Specifications Of 15a, 2p, And 240v, Single. • Storage/closet - This Area Is For Storing Cleaning Materials Such As Detergents, Disinfectants, Brushes, Mops, And Other Sanitation Tools Used In Dietary Operations. - Planning Relationships: A. Located Within Patients Dishwashing Area. - Lighting System: B. For General Illumination, Provide At Least 150 Lux. - Power System: C. Also, Provide At Least One (1) Unit Of Outlet For Emergency Light With Specifications Of 15a, 2p, And 240v, Single. • Lpg Storage Area - This Area Is Well-ventilated Space Designed For The Safe Storage Of Lpg Tanks Used In Kitchen Operations. The Area Will Be Located Away From Open Flames, Heat Sources, And High-traffic Zones To Ensure Safety. It Will Feature Non-combustible Walls, A Fire Extinguisher, Proper Signage, And Adequate Lighting. The Space Will Also Include Provisions For Leak Detection, An Accessible Emergency Shut-off Valve, And Ground-level Storage To Prevent Accidental Tipping Of Lpg Tanks. - Lighting System: A. For General Illumination, Provide At Least 250 Lux. - Power System: B. Also, Provide At Least One (1) Unit Of Outlet For Emergency Light With Specifications Of 15a, 2p, And 240v, Single. • All Gender / Pwd Toilet & Bath - This Area Is Designed To Be Inclusive, Complying With The Updates To The Amended Irr Of Bp 344. It Ensures Accessibility For All Genders And Persons With Disabilities (pwd), Featuring Wide Doors, Support Bars, Urinal And Spacious Layout To Meet The Latest Standards For Accessibility And Comfort. - Planning Relationships: A. Accessible To All Staffs. B. Minimum Of One (1) Toilet On Each Floor Accessible To Disabled. - Lighting System: C. For General Illumination, Provide At Least 150 Lux. - Fire Alarm System: D. Provide At Least One (1) Unit Smoke Detector. • Electrical Room - Located On The Ground Floor In The Staff Hallway, It Is Strategically Placed To Maintain Separation And Safety While Ensuring Easy Access For Maintenance And Operation. - Lighting System: A. For General Illumination, Provide At Least 250 Lux. - Fire Alarm System: B. Provide At Least One (1) Unit Smoke Detector. - Power System: C. Provide At Least One (1) Units Of Outlet With Specifications Of 15a, 2p, 240v, Duplex, Grounding Type And Universal Slots. Also, Provide At Least One (1) Unit Of Outlet For Emergency Light With Specifications Of 15a, 2p, And 240v, Single. • Common Toilet With Sink (female And Male Toilet Cubicle) - This Area, Featuring Separate Female And Male Toilet Cubicles, Will Serve Both The Dietitians/staff Office And The Hospital Staff Dining Room. It Will Be Designed For Accessibility And Include Standard Fixtures, Such As Sinks, Mirrors, And Hand Dryers Or Paper Towel Dispensers. The Space Will Prioritize Hygiene And Ease Of Maintenance With Durable, Easy-to-clean Surfaces, Adequate Lighting, And Ventilation. - Planning Relationships: A. In Between Dietitians/staff Office And Hospital Staff Dining - Lighting System: B. For General Illumination, Provide At Least 150 Lux. - Fire Alarm System: C. Provide At Least One (1) Unit Smoke Detector. Xiv. Design Parameters (architectural) A. Codes And Standards The Architectural Works Shall Be In Accordance With The Following Laws, Codes And Standards.  Laws And Codes: 1. National Building Code Of The Philippines And Its Latest And Amended Irr 2. Ra 9266 Or Architecture Law And Its Latest And Amended Irr 3. Ra 4226 Or Hospital Licensing Act And Its Latest And Amended Irr 4. Bp 344 Or Accessibility Law And Its Latest And Amended Irr 5. Ao 35, S. 1994 Or Ao Pertaining To The Control Of Radiation Hazards 6. Ra 9514 Fire Code Of The Philippines 7. Existing Local Codes And Ordinances. 8. And Other Laws That Applies To The Projects  Standards: 1. Bureau Of Product Standards (bps) 2 Underwriters Laboratory (ul) 2. Doh Technical Guidelines For Hospital & Health Facilities Planning And Design – Level 3 B. General Drawing Guidelines 1. General  All Drawings Shall Be Computer-drafted. Drawings Shall Be Submitted Both In Printed And Electronic Copies.  Keep The Same Orientation For All Plans. The North Orientation Shall Be Indicated In All Architectural Floor Plans. The Orientation Of The Architectural Plans Shall Be Consistent With All The Engineering Plans.  Existing Buildings And New Works Shall Be Clearly Indicated And Labeled In The Site Plans.  Detailed Plans Shall Have A Scale Not Smaller Than 1:50 Meters.  Spot Detailed Plans, Elevations, And Sections Shall Have A Scale Not Smaller Than 1:10 Meters.  Avoid Notes Such As ‘see Architectural Detail’ Or ‘see Structural’. Always Refer With A Callout To The Specific Detail Drawing And Sheet Number. 2. Site Plans  The Site Plans Shall Have A Scale Not Smaller Than 1:500 Meters. 3. Floor Plans  All Plans Shall Be 1:100 Meters. The Same Scale Shall Be Used For The Rest Of The Architectural, Structural, Sanitary, Plumbing, Electrical And Mechanical Plans, Except For Each Trade’s Site Plan, Detailed Plans And Spot Details.  Elevation Callouts Shall Be Indicated On The Floor Plans And Shall Be Consistent With The Elevation Drawing.  Section Line Callouts On The Floor Plans Shall Be Consistent With The Section Drawing.  Floor Plans Shall Be Indicated With Boxed Room Callout Numbers, Including The Callout For Floor Finishes And Wall Finishes.  Floor Elevations Shall Be Indicated In The Floor Plans. This Shall Be In Reference To The Natural Grade Line Or The Established Finished Floor Lines Of The Adjoining Existing Buildings.  The Location Of Mechanical Equipment, E.g. Air Conditioning Shall Be Indicated In The Floor Plans. This Shall Be Consistent With The Mechanical And Electrical Plans.  Door Callouts Shall Be Circles With The Proper Numbering, E.g. D-01.  Window Callouts Shall Be Hexagons With The Proper Numbering, E.g. W-01. 4. Elevations And Sections  Finish Floor Lines And Top Of Truss Lines Shall Be Consistent In All The Elevations, Sections And Structural Plans And Details. 5. Reflected Ceiling Plans  Reflected Ceiling Plans Shall Be Indicated With Boxed Room Callout Numbers, Including The Callout For Ceiling Finishes And Lighting Fixtures.  Ceiling Height Relative And In Reference To The Finish Floor Line Shall Be Indicated In The Reflected Ceiling Plans In Each Room With Boxed Dimensions. This Is To Ensure That The Ceiling Heights Of All Rooms Are Established Whether Or Not Reflected In The Sections.  The Description And Location Of The Fixtures, E.g. Lighting, Smoke Detectors, Air Condition Vents, Exhaust Fans, In The Reflected Ceiling Plans Shall Be Consistent With The Electrical And Mechanical Plans. 6. Roof Plans  Location Of All Downspouts Shall Be Indicated In The Roof Plans. 7. Doors And Windows  Door And Window Schedules Shall Indicate The Type Of Door Or Window, The Number Of Sets, The Location/s Of The Door Or Window, The Materials And Accessories Included And Other Special Specifications, E.g. Color Or Finish. All Windows Above Ground Floor Should Be Of Awning With An 45 Deg. Opening Angle. 8. Details  Provide A Minimum Of One (1) Bay Section Of A Scale Not Smaller Than 1:50 Meters For Each Major Building Preferably Cut Along The Area With Special Construction Design.  Provide Spot Detail Plans, Elevations And Sections Of A Scale Not Smaller Than 1:10 Meters For Special Designs With Aesthetic Treatment And Ornamentation.  Provide Detailed Plans Of A Scale Not Smaller Than 1:50 For All Areas Needing Tile Pattern, E.g. Lobby, Corridor, Entrance Walk, Showing The Position And Pattern Of Tiles.  Centerline Location Of Plumbing Fixtures Shall Be Indicated In Detailed Plans With Lines Of Reference And Its Corresponding Dimensions. This Is To Indicate The Exact Locations Of The Plumbing/sanitary Roughing-ins. C. Site Works 1. The Master Site Development Plan Of The Hospital Shall Include The Following:  Contour And Survey Of The Lot, Including Bearing And Distance Of The Property Line  Road Network And Curbs And Sidewalks  Parking Spaces  Reference Location Of Existing Trees  Reference Location And Footprint Of Existing Buildings, With The Corresponding Building Names And Dimensions, Including Distances Between Adjacent Buildings, And Distances Between Buildings And The Nearest Property Line  Reference Location Of Utilities, E.g. Water Reservoirs, Septic Tank, Wastewater Treatment Plant, Powerhouse, Transformers, Waste Storage Area, Security Outposts 2. The Layout Of The Buildings On The Site Shall Be Zoned According To The Service It Provides:  The Outer Zone Shall Include All Front-line Services, E.g. Emergency, Out-patient, X-ray, Laboratory And Other Ancillary Departments.  The Inner Zone Shall Include The Wards.  The Deep Zone Shall Include Services Like The Operating Room, Delivery Room, Nursery, Intensive Care Unit And Other Sensitive Hospital Services.  The Service Zone Shall Include Non-medical Services But Are Essential To Hospital Operations, E.g. Staff Lounge And Lockers.  There Shall Be A Separate Road Network And Entry/exit For The Public And The Service Vehicles, E.g. Ambulance, Waste Collection Vans, Delivery Trucks.  In Limited Lot Areas, Buildings Should At Least Be Spaced Four (4) Meters Apart To Allow Natural Light And Ventilation.  Covered Walkways Shall Be Provided For Access And Connection To All The Buildings.  Ramps Shall Be Provided In All Main Entrances Of The Buildings And Other Access Openings To Walkways Leading To Other Buildings. D. Building Architectural Works 1. Floor Plans  The Structural, Sanitary, Plumbing, Electrical And Mechanical Designs Are Required To Refer To The Architectural Plans And Specifications In Case Of Discrepancies. If An Engineering Design Will Have Any Possible Conflict Or Interference On The Architectural Design, The Latter May Be Adjusted Provided That The Aesthetic Value Will Not Be Compromised.  The Architectural And Engineering Plans Shall Be Consistent All Throughout In Terms Of Dimensions And Locations Of Columns, Beams, Walls, Roof Line, Conduits, Ducts, Pipes, And Fixtures, Among Others. Column And Beam Grid Lines Shall Also Be Consistent In All The Architectural And Engineering Plans.  Verify And Coordinate Floor Plans With The Mechanical, Electrical And Sanitary Design With Regard To The Requirements For Mechanical Rooms, Ahu Rooms, Electrical Rooms, Pipe Chase, And Other Engineering Requirements.  Public Toilets Shall Have Provisions And Fixtures For Persons With Disability As Required By Bp 344. If Enough Space Allows, Toilets Specially Made And Designated For Persons With Disability Is Preferable. 2. Walls  Exterior Walls Shall Be 200mm. Thick, While Interior Walls Shall Be 150mm. Thick. This Is Indicative Of The Finished Wall Thickness Including The Plastering And Tile Works.  Used Soundproofed Wall Materials For Areas With Indicated “soundproofed”. Walls With An Stc Rating Of At Least 45-50 Is Recommended. In Areas Where High Confidentiality Or Privacy Is Required (e.g., Patient Rooms, Doctor’s Offices Near Noisy Zones), Consider An Stc Rating Of 55-60.  Double Layer Of Drywall: Use Two Layers Of Drywall On Either Side Of A Metal Or Wood Stud Frame For Enhanced Soundproofing.  Acoustic Insulation: Use High-density Insulation Like Mineral Wool Or Acoustic Fiberglass In Wall Cavities To Absorb Sound.  Higher Mass: Increase The Wall's Mass With Materials Like Masonry Or High-density Concrete, Which Can Significantly Reduce Sound Transmission.  Toilet Wall Tiles Shall Be 300mm. X 300mm. For Areas Of Six (6) Square Meters Or Below. Toilet Wall Tiles Shall Be 300mm. X 600mm. For Areas Above Six (6) Square Meters.  Layout And Work On Wall And Floor Tiles Must Be Aligned, Plumb, Level, And Square.  All Edges, Corners And Intersections Of Toilet Tiles, Including The Top-most Tile Not Reaching The Ceiling Shall Be Provided With Polyvinyl Chloride Tile Trims.  Tile Color And Design Shall Be Approved First Before Installation. 3. Floors  If Floor Tiles In Two Adjacent Rooms With Different Material, Color Or Design Meet At The Door Opening, The Cut Shall Be Located Middle Of The Door Thickness When In A Closed Position. Provide Details In The Floor Pattern Design.  Floors At The Openings Of Toilets For Persons With Disability Shall Be Sloping. Indicate In The Plans And Sections.  The Size Of The Toilet Floor Tiles Shall Be 300mm. X 300mm. For Areas Of Six (6) Square Meters Or Below. Toilet Floor Tiles Shall Be 300mm. X 600mm. For Areas Above Six (6) Square Meters. Indicate The Tile Pattern.  The Size Of The Pantry/lounge Floor Tiles Shall Be 600mm. X 600mm. Indicate The Tile Pattern.  The Size Of The Floor Tiles Of The Offices And Wards Shall Be 600mm. X 600mm, Or Bigger Depending On The Proportion To The Size Of The Room. Indicate The Tile Pattern.  The Size Of The Floor Tiles Of The Lobby And Corridor Shall Not Be Less Than 400mm. X 400mm. The Tile Size Of 600mm. X 600mm. Is Recommended For Bigger Areas. Indicate The Tile Pattern.  Layout And Work On Wall And Floor Tiles Must Be Aligned, Plumb, Level, And Square.  All Edges, Corners And Intersections Of Toilet Tiles, Shall Be Provided With Polyvinyl Chloride Tile Trims.  Tile Color And Design Shall Be Approved First Before Installation. 4. Ceiling Works  Ceiling Height For Areas With Special Aesthetic Treatment, E.g. Lobby, Major Conference Room, Auditorium, Executive Office, Shall Be Proportional To The Area Or Room Or As Required By The Designer. However, This Shall Not Be Lower Than 2700mm. Provide Details.  If Acoustic Boards On Aluminum T-runners Would Be Used For The Ceiling, Layout Should Be On Center And Avoiding Cut Pieces. If The Remaining Perimeter Of The Ceiling Is Less Than 600mm. Wide, It Shall Be Designed Complimentary With Fiber Cement Boards On Light Gauge Metal Furring. Likewise With Acoustic Boards In Big Areas, E.g. Offices, And Wards, Shall Be Designed In A Way To Break The Redundancy. Provide Details.  Soffit Of Exterior Beams And Slabs Shall Have Drip Moulds To Prevent Damage Due To Water Sipping Into The Eaves Or Ceiling. Section Details Shall Be Required To Show The Drip-mould.  Acoustic Panels: Adding Absorptive Finishes, Such As Fabric-covered Acoustic Panels, Can Help To Dampen Internal Reflections And Improve Sound Quality Within Rooms, Although These Don’t Block Sound But Reduce Reverberation.  Non-cove Light Placement: Instead Of Cove Lighting, Use Flush-mounted Lighting Directly In The Ceiling With Sealed Housings That Prevent Dust Buildup. Fixtures Should Be Durable, Non-reflective, And Easy To Clean Without Requiring Special Maintenance Procedures. 5. Doors And Windows  Major Rooms That Require Security Shall Have Sturdy Doors E.g. Wood Panel, And Metal.  Minor Rooms That Do Not Require Security Shall At Least Have Wood Flush Doors.  Toilets And Other Wet Areas Shall Have Steel Doors.  Heavy-use Doors, E.g. Operating Rooms, Delivery Rooms, Should Be Provided With Stainless Steel Kick Or Push Plates And Door Closers.  Fire Escape Doors Should Be Provided With Panic Hardware And Door Closers, And Shall Conform With The Requirements Of The Fire Code Of The Philippines.  Aluminum Frames Of Glass Doors Shall Be Powder-coated.  Door Finish And Color Shall Be Approved First Before Application.  Window Sills Shall Be Slightly Sloped Outwards To Prevent Damage To Windows And Paint Due To Water Seepage. Section Details Shall Be Required To Show This Slope.  All Doors Of A High-occupancy Room Shall Swing Outwards And As Required By The Fire Code Of The Philippines.  Door Jambs With No Moulding/casing Installed On Concrete Walls Shall Have Construction Grooves All Around. Provide Details.  All Doors And Windows Shall Have Reinforced Concrete Lintel Beams. Provide Details.  Door Seals And Frames: For Soundproofed Rooms, Also Use Solid-core Doors With Perimeter Seals To Prevent Sound From Leaking Through Door Frames. 6. Stairs, Ramps And Corridors  Ramps For Persons With Disability Shall Have A Slope Not Higher Than 1:12. Handrails And Clearances Shall Conform With The Requirements Of Bp 344.  Regular Stairs Shall Have Risers At 150mm. High And Treads At 300mm. Wide. Fire Stairs Could Have A Maximum Riser At 200mm. And Tread At 250mm. Handrails Shall Be 1100mm. High. Clearances Shall Conform With The Requirements Of The Fire Code Of The Philippines.  Corridors Shall Have A Minimum Unobstructed Width Of 2450mm. This Shall Be Measured Clear From The Surface Of The Finished Wall And Not On-center Of The Rough Chb Wall.  Corridors Shall Not Be Areas For Temporary Or Permanent Storage Of Stretchers, Wheelchairs, Trolleys, Food Carts, Oxygen Tanks Or Other Movable Hospital Equipment. Storage Or Parking Spaces Shall Be Provided For These.  Corridors And Exit Doors Shall Conform With The Requirements Of The Fire Code Of The Philippines. 7. Fixtures And Accessories  Three-way Electrical Light Switches Shall Be Provided At The Foot And The Top Of The Stairs Per Floor. Likewise, At Both Ends Of A Long Corridor.  Electrical Light Switches Shall Be Located By The Knob Side Of The Door.  Electrical Switches And Outlets Shall Be Installed Plumb And Level.  Public Toilets Shall Always Be Provided With Heavy-duty Soap Dispensers And Electric Hand Dryers.  Public Toilets Shall Always Be Provided With Stainless Steel Handrails In Conformity To The Requirements Of Bp 344.  A Drainage Line Shall Be Provided For Window-type Air Conditioners. Likewise, Split-type Air Conditioners Located In The Interior Part Of The Building Shall Be Located Adjacent To Areas With Drainage Lines, E.g. Toilets, Downspouts, Balconies.  Seal Gaps And Openings: Ensure All Joints, Gaps, And Penetrations (e.g., Electrical Outlets, Ducts) Are Sealed With Acoustical Caulk Or Gaskets To Prevent Sound Leakage.  Sterile Area Lighting Type: Use Sealed, Recessed, Or Surface-mounted Led Fixtures That Are Flush With The Ceiling Surface To Prevent Dust Accumulation. 8. Roofing Works  The Section Of The Roof Gutters Shall Be Designed, In Case Of A Clogged Downspout, So That The Overflow Of Water Will Be Directed Outside Of The Building And Not Towards The Eaves Or Interior Ceiling To Prevent Any Damage. Provide Details.  Avoid Valley Or Inside Gutters In Roof Design. But In Cases Required In Aesthetic Design, Valley Or Inside Gutters Shall Be In Stainless Steel Or Concrete Gutters With Membrane-type Waterproofing, And The Section Shall Be Designed With A Capacity For Big Volume To Prevent Any Damage Due To Overflow. Provide Details.  Parapets, Designed As A Roof Protection From The Winds, Must Be Designed To Satisfy The Preceding Parameters. Provide Details.  The Slope Of The Roof Shall Not Be Less Than 30 Degrees. 9. Painting  Painted Ceiling Shall Be In Flat Latex Finish, While Cornices And Mouldings Shall Be In Gloss Enamel Finish.  Painted Interior Wall Shall Be At Least In Semi-gloss Latex Finish For Ordinary Rooms, E.g. Offices, Unless Specified To A Higher Type Of Paint.  Patient-related Rooms, E.g. Emergency Rooms, Out-patient Departments And Wards, Shall Be In Anti-bacterial And Odor-absorbent Paint Finish.  Special Rooms, E.g. Operating Rooms, Delivery Rooms, And Laboratories Shall Also Be In Anti-bacterial And Odor-absorbent Paint Finish.  Painted Exterior Wall Shall Be At Least In Moisture-resistant/water-repellent Solvent-based Paint Finish, Textured Or Smooth, Unless Otherwise Specified.  Paint Color And Shade Shall Be Approved First Before Application. D. Specific Requirements 1. Provide Spot Detail Plans And Sections Of The Following:  Gutter, Eaves, And Parapet  Ceiling - Covelight, Special Connections And Design, Mouldings, Valances  Stairs - Handrail, And Baluster Design  Ramps - Handrail Design And Floor Pattern  Doors, Windows And Gates - Grille Works,  Special Architectural Treatment And Design, E.g. Façade Design, Special Window And Door, Counters  Special Carpentry Works, E.g. Partitions, Cabinetry  Building And Room Signages And Wayfinding Systems  All Pwd Toilets Shall Be Labelled “all Gender / Pwd Toilet”  Other Details As May Be Required 2. Provide Room Data Sheets, Including Detail Floor Plan, Ceiling Plan And Sections Of The Following Rooms, In Coordination With The Requirements Of The Electrical, Sanitary And Mechanical Designs: A. Cooking Area, Including Furniture And Equipment With Specific Dimensions Of The Location Of Fixtures And Accessories, And In Coordination With The Requirements Of The Electrical And Mechanical Engineering Design. B. Hospital Staff Dining C. D. (all Blanks Shall Be Filled As Required By Or Applicable To The Project.) E. Summary Of Materials  Materials To Be Used Shall Be Fire-resistant, Non-toxic, Moisture-resistant And Termite-resistant, E.g. Fiber Cement Board, Light-gauge Steel Frame, Polyvinyl Chloride Ceiling Panels.  Wet Areas, E.g. Toilets, And Pantry/lounge Shall Use Non-skid/non-slip Vitrified Ceramic Floor Tiles.  Heavy Traffic Areas, E.g. Lobby, And Corridor Shall Use Heavy-duty Seamless Granite Floor Tiles Or A Higher Type Of Floor Material.  Ramps And Stairs Shall Use Non-skid/non-slip Floor Tiles, Materials As Specified.  Aluminum T-runners Shall Be Powder Coated.  Metal Rod Hangers With Adjustable Clips, And Not Galvanized Iron Wires, Shall Be Used To Support And Suspend The Aluminum T-runners And Light Gauge Metal Furrings.  Roofing Sheets Shall Be Ga.# 24 Aluminum-coated, Pre-painted, And Pre-formed. F. Drawing Requirements: See Attached Doh Checklist Of Drawings. -end Of Architectural Design Parameters- Xv. Design Parameters (structural/civil Works) A. Codes And Standards The Civil/structural Design Shall Be In Accordance With The Following Codes And Standards  Codes 1. National Structural Code Of The Philippines (nscp) 2010 2. National Building Code Of The Philippines And Its Revised Irr 3. Accessibility Law 4. Local Codes And Ordinances  Standards 7. Bureau Of Product Standards (bps) 8. Philippine National Standards (pns) 9. Dpwh Blue Book 10. American Concrete Institute (aci) 11. American Society For Testing Materials (astm) 12. American Welding Society (aws) B. Site Works Based On The Master Site Development Plan Of The Hospital, Provide Where Applicable Complete Design And Details Of Hospital Road (concrete With Curb And Gutter, Including Drainage) Network, Walkways, Parking Areas And Fencing. 1. The Main Hospital Road Shall Be Capable Of Two-way Traffic (at Least 6mts. Width) With A Minimum Thickness Of 150mm (8 Inches). Concrete Strength Should Be At Least 3000psi. Interior Roads (leading To Support Facilities) Shall Be Designed To Accommodate Delivery Vehicles, And Fire Trucks In Case Of Emergency. 2. Walkway Should Be At Least 100mm Thk. With Concrete Strength Of 2500psi. Ramps Should Be Provided, Instead Of Steps, For Any Change In Elevations. 3. Parking Area Slabs Should Be At Least 150mm Thk. With Concrete Strength Of 3000psi. 4. Fences Should Be Seen Through In Front Of The Hospital While The Tree (3) Other Sides Should Be Concrete Hollow Blocks With Minimum Height Of 2 Meters And To Be Provided With Perimeter Lighting. See-through Fence Design Will Be Made Of 32mm Square Bars Spaced At 100mm On Center And Provided With Three (3) Concrete Hollow Blocks (45mm High) Zocalo Walls. C. Buildings 1. The Hospital Buildings Should Be Designed Using A Seismic Importance Factor Of 1.5 For The Immediate Occupancy Category. Buildings Should Be Designed In Accordance With Nscp Requirements Up To Magnitude 7 For Those Near Seismic Source Type A. Seismic Gaps Between Buildings (old And New) Should Be Properly Observed. 2. The Hospital Buildings Should Be Designed Also Using Wind Importance Factor Of 1.15 (especially For Design Of Trusses/roofing System). Concrete Gutters And Parapet Walls Should Be Provided As Additional Protection To The Roofing System During Strong Typhoons. Wind Velocity Of 300-350 Kph Shall Be Considered Upon The Recommendation Of Structural Engineer 3. The Structural Designer Should Verify With Philippine Volcanology And Seismology (phivolcs) The Distance Of The Proposed Hospital To Nearest Active Fault Lines And With The Denr For Geo-hazard Mapping. 4. Soil Investigation (at Least Three Boreholes) Should Be Conducted To Determine Soil Bearing Capacity And Recommended Foundation Design (applicable Even For One Storey Structure). 5. The Structural Designer Is Encouraged To Use Fire-resistive And Non-toxic Materials. D. Details – The Following Shall Be Provided: 1. Connection Details Of Beams And Columns Following The Requirements Of Nscp On Confined Areas. 2. Connection Of Trusses To Beams And Columns. 3. Splicing Details Of Reinforcing Bars On Columns And Beams And The Required Bar Cut-off Points. 4. Details For Connection Of New Construction & Old Construction Structural Members Such As Expansions Joints For Thermal Expansion/contraction. 5. Include Thermal Expansion/contraction Prevention Methodologies Specifically On Soft Joints Areas Between Structural And Architectural Members. E. Summary Of Materials 1. Concrete Shall Be Portland Cement And Conforming To Astm Specification C150, Type I To Type Ii 2. Coarse Aggregates Shall Consist Of Washed Gravel, Crushed Stone Or Rock Or A Combination Thereof Conforming To Astm C33 3. Concrete Hollow Blocks Shall Be A Standard Product Of Recognized Manufacturer Conforming To Pns 16 With At Least 350psi Strength. 4. Reinforcing Bars Shall Conform With Pns Grade 60 For 16mm Dia. And Above And Pns Grade 40 For 12mm Dia And Below. 5. Structural Steel Shall Conform With Astm A36/a6m 6. Bolts And Studs Shall Conform With Astm A 325 7. Welding Electrodes Shall Be E60 Or E 70 And Conform With Aws F. Drawing Requirements: See Attached Checklist -end Of Structural/civil Works Design Parameters- Xvi. Design Parameters (sanitary/plumbing Works) A. Codes And Standards The Sanitary/plumbing Design Shall Be In Accordance With The Following Codes And Standards.  Codes: 1. National Building Code Of The Philippines And Its New Irr 2. Fire Code Of The Philippines 3. National Plumbing Code Of The Philippines (npcp) 4. Sanitation Code Of The Philippines 5. Existing Local Codes And Ordinances.  Standards: 1. Bureau Of Product Standards (bps) 2. Philippine National Standards For Drinking-water 3. Underwriters Laboratory (ul) 4. Doh National \ Laboratory (nrl) 5. Doh Health Care Waste Management Manual 6. National Water Resources Board (nwrb) 7. National Plumbers Association Of The Philippines (nampap) 8. Philippine Society Of Sanitary Engineers, Inc. (psse) B. Site Works  Based On The Master Site Development Of The Hospital, The Site Works Shall Provide Complete Layout Of The Following: 1. Storm Drainage Network, Indicating Drainage Manholes And Pipe Culvert; 2. Sewerage Pipe Network, Indicating Sewage Manholes, Sewage Pipes And The Location Of The Proposed Sewage Treatment Plant; And 3. Water Supply Network, Indicating The Location Of Water Service Entrance, Cisterns, Elevated Water Tank And Proposed Pump House.  The Storm Drainage Network Shall Accommodate The Magnitude Of Peak Rates Of Surface Run-off Including Drainage Coming From The Buildings. The System Shall Be Capable Of Handling The Design Flows Routing To The Designated Outfall; For Rainfall Calculation And Sizing Of Drainage Pipes, Refer To Table-d2, Appendix-d, National Plumbing Code Of The Philippines And Current Rainfall Record From Pagasa.  The Sewerage Pipe Network Design Shall Accommodate All Sewage Coming From All The Facilities, Conveyed By Gravitational Flow Leading To The Sewage Treatment Plant; Per Capita Wastewater Demand: 100-130 Gal/capita/day Per Bed C. Building Facilities Sanitary/plumbing System 1. Sewer Line And Vent System  Provide Complete Sewer Line And Vent System From All (domestic) Plumbing Fixtures And Floor Drains, Laid By Gravity Flow Leading To The Sewage Treatment Plant (stp);  For Demand Weight Of Fixtures In Fixture Units; Refer To Appendix A, Table A-2, Npcp 2. Wastewater Line And Vent System  For All Wash Areas Dealing And Generating With Oil/grease, Provide Separate Wasteline And Vent System And Solely Tap To The Proposed Grease Trap And Then Connect Its Effluent To The Sewage Treatment Plant.  For Estimated Demand Weight Of Fixtures In Fixture Units; Refer To Appendix A, Table A-2, Npcp Waterline System  Provide Complete Cold Water Supply Pipes To All Plumbing Fixtures. From The Main Water Source, The Water Shall Be Pumped To The Elevated Water Tank (ewt) And Conveyed To The Fixtures By Gravity System And Or Distributed To Fixtures By Transfer Pumped With Constant Pressure Through A Pneumatic Storage Tank, Whichever Is Feasible. 4. Storm Drainage System  Complete Storm Drainage System Shall Be Provided For All Roofs, Canopies, Concrete Ledges And Balconies Including Condensate Drains Laid For Gravity Flow Connected To A Leader/pipe Line Leading To The Natural Ground Level Storm Drainage Network. D. Specific Requirements  Provide Details Of The Following: 1. Grease Trap (for Dietary) 2. Provision Of Water Softener 3. Fiberglass Pressure Tank E. Summary Of Materials  Sewer And Vent Pipes; Unplasticized Polyvinyl Chloride (upvc) Extra Series 1000 (conforming To Iso 3633 Astm D2729 Including Trims And Fittings)  Storm Drainage Pipes; Downspouts, Unplasticized Polyvinyl Chloride (upvc) Extra Series 1000 (conforming To Iso 3633 Astm D2729 Including Trims And Fittings, Bps Certified)  Drainage Pipes; 250mm Dia. And Below, Non-reinforced Concrete Pipe (nrcdp)  300mm Dia. And Above, Reinforced Concrete Pipe (rcdp)  Drainage Manholes; Street Inlet, Curb Inlet, Traffic Type Reinforced Concrete Area Drain/catch Basin, Reinforced Load Bearing Chb  Sewage Manholes; Traffic Type Reinforced Concrete With Standard Steel Brass Cover  Wastewater Pipeline; Extra Heavy (xh) Single Hub, Hub Less Cast Iron Pipes And Fittings (cip) Conforming To Astm Standard 888  Cleanouts; Cast Iron Brass With Countersunk Plug (bps Certified)  Floor Drains/deck Drains; Cast Iron Brass (bps Certified)  Gutter Drains; Cast Iron Dome Type Brass (bps Certified)  Cold Waterline Pipes; For Buildings, Polypropylene Pn10 Fusion Weld Pipes Including Trims And Fittings (bps Certified)  Hot Waterline System; For Buildings, Polypropylene Pn20 Fusion Weld Pipes Including Trims And Fittings (bps Certified)  Trench Grating; Galvanized/stainless Steel Iron Grates  Plumbing Fixtures Including Trims, Fittings And Accessories; (bps Certified)  Water Closet-tank Type Push Button Flush  Lavatory - (pedestal/counter Type) With C-spout Spray Faucet  Kitchen Sink-ga#16 Stainless Steel Seamless Bowl With Gooseneck Faucet  Urinal-wall Hung Flush Valve Type  Plumbing Fixtures At Sterile Areas; A. Scrub-up Sink-ga#16 Stainless Steel (single/double Bowl) Compartment With Knee Operated And Or Censor Controlled Spay Faucet B. Surgical Soap Dispenser-ga#16 Stainless Steel Foot Operated C. Laboratory Sink-ga# 16 Stainless Steel Deep Seated Seamless Bowl Compartment With C-spout Spray Faucet F. Drawing Requirements: See Attached Doh Checklist Standards Based On Revised Irr Of The National Building Code Of The Philippines (pd 1096) -end Of Sanitary/plumbing Works Design Parameters- Xvii. Design Parameters (mechanical Works) A. Codes And Standards The Mechanical Design Shall Be In Accordance With The Following Codes And Standards.  Codes: 1. National Building Code Of The Philippines And Its New Irr 2. Fire Code Of The Philippines 3. Mechanical Engineering Code Of The Philippines (me Code) 4. Existing Local Government Codes And Ordinances.  Standards: 1. Bureau Of Product Standards (bps) 2. Philippine National Standards (pns) 3. Underwriters Laboratory (ul) And Factory Mutual (fm) 4. International Electrotechnical Commission (iec) 1988 5. National Fire Protection Association (nfpa) 6. National Fire Protection Association (nfpa) 99 Standard For Health Care Facilities. 7. American Society Of Heating, Refrigeration And Air Conditioning Engineers (ashrae). 8. Center For Disease Control And Prevention (cdc) Manual. B. Automatic Fire Sprinkler System  The Automatic Fire Sprinkler System Shall Be Composed Of Complete Plans And Drawings Of The Following: 1. Site Development Plan And Vicinity Map, Indicating The Location Of The Buildings, Firewater Reserve Tank, Firewater Line, Yard Loop And Private Fire Hydrant. 2. General Notes, Legends And Symbols Including Schematic Diagram Of The Fire Sprinkler System And Schematic Diagram Of Alarm Monitoring System. 3. Floor Layout And Isometric Layout Of The Automatic Fire Sprinkler System Indicating Pipe Sizes And The Location Of The Pipes, Valves, Sprinkler Heads, Riser Nipples, Fire Hose Cabinets, Sprinkler Main Riser, Drain Pipes, Cross Mains, Branch Lines, Inspector’s Test Connections, Hangers And Sway Braces. 4. Equipment Schedule, Detail Drawings, Fire Pump And Jockey Pump Layout. 5. Architectural, Structural, Electrical And Plumbing Drawings Of The Firewater Tank And Pumphouse.  An Automatic Fire Sprinkler Shall Be Provided In All Hospital Building Except For Those Fire Resistive One-storey Hospital Building.  Hazard Classification Shall Be Light Hazard Occupancy.  Area Of Coverage Shall Be 146 Square Meters And Water Density Shall Be 4.07 Lps/sq. M.  Protection Area Per Sprinkler Head Shall Be 20 Square Meters At 2.2 Meters Minimum Distance Between Sprinklers And 4.2 Meters Maximum Spacing.  All Floor Control Valves Shall Be Equipped With Supervisory Switch, Water Flow Detector And Drain System.  Water Supply Shall Be Horizontal Split Case Centrifugal Fire Pump With Diesel Engine Or Ac Motor And A Vertical In-line Jockey Pump With Controller.  Firewater Reserve Tank Shall Be Ground Level Monolithic Concrete Tank Sized For A Minimum Of 30 Minutes.  Hydraulic Calculations Report Shall Be Based On Npfa-13 Format. C. Ventilation And Air Conditioning System  The Ventilation And Air Conditioning System Shall Be Composed Of Complete Plans And Drawings Of The Following: 1. General Notes, Legends And Symbols Including Schematic Diagram Of The Ventilation And Air Conditioning System. 2. Floor Layout Of The Ventilation And Air Conditioning System Indicating The Capacity And Location Of The Air Conditioners And Fans. 3. Duct Layout Indicating Duct Sizes, Route And Location Of The Dampers, Diffusers, Return Air Register, Hangers And Sway Braces. 4. Refrigerant Piping Layout Indicating Pipe Sizes, Location Of Valves, Hangers And Sway Braces. 5. Equipment Schedule And Details Drawings Of Air Conditioners And Ventilating System.  Air Conditioning System Shall Be Provided In All Patient’s Private Rooms, Operating Rooms, Delivery Rooms, Offices And Other Areas Where Conditioned Air Is Necessary.  Cooling Load Calculations Report Shall Be Manual Or Computer Generated, Hourly Analysis Program Which Includes Heat Transmission Coefficients, Solar Heat Gain Factors And Corrected Cooling Load Temperature Difference Calculations.  Split Type Air Conditioners Will Be Used At Areas With Larger Capacities.  Window Type Air Conditioners Shall Be Used In Areas With Exterior Wall Exposure.  Centralized Air Conditioning Will Be Used As Indicated On Space Requirements (e.g. Sterile Hallways).  Maintain An Air Change Rate Greater Than Or Equal To 12 Air Changes Per Hour Or 145 Liters Per Second Per Patient.  Ceiling Cassette Type Exhaust Fans With Integral Air Diffuser Shall Be Provided In All Toilets.  Ceiling Fans, Orbit Type With 360° Oscillation Shall Be Provided In All Non-air-conditioned Rooms, As Mentioned On Space Requirements. D. Specific Requirements  Provide Details Of The Following: 1. Lpg Pipeline 2. Kitchenhood And Smokestack E. Summary Of Materials 1. Automatic Fire Sprinkler System A. The Fire Pump Shall Be Ul Listed/fm Approved, Diesel Engine Or Electric Motor Driven, Designed Specifically Intended For An Automatic Water Sprinkler Protection System. B. The Jockey Pump Shall Be Ul Listed/fm Approved, Electric Motor Driven, 220v, 3-phase, 60 Hertz, And Electric Power Connection. C. Sprinkler Head Shall Be Ul Listed/fm Approved, Pendant, Upright Or Sidewall Unit, 83 Lpm Flow Capacity Per Head And Temperature Fusing At 57.5° C To 74°c. D. The Alarm Assembly Shall Be Ul Listed/fm Approved, Constructed And Installed That Any Flow Of Water From The Sprinkler System Equal To Or Greater Than That From The Single Automatic Head Shall Result In An Audible And Visual Sign In The Vicinity Of The Building. E. Alarm And Supervision System Of The Automatic Water Sprinkler Shall Include The Monitoring Water Flow Switch At Each Floor Of The Building, Fire Pump And Jockey Pump Running Condition And Power Supplies, Level Of Water In The Reservoir And Control Valves. F. Pipes Shall Be B.i. Schedule 40. Screw Fittings Shall Be Used For Inside Piping. 2. Air Conditioning And Refrigeration System A. Refrigerant Pipes Shall Be Copper Tubing, Type L Or K Black Steel Pipe, Schedule 40 For Size Of 100mm Diameter And Smaller. Pipe Over 100mm Shall Be Black Steel Pipe Schedule 40. B. Black Steel Pipes Shall Be Standard Seamless, Lap-welded, Or Electric Resistant Welded For Size Of 50mm Diameter And Larger, Screw Type For Size 38mm Diameter And Smaller, Fittings For Copper Tubing Shall Be Cast Bronze Fitting Designed Expressly For Brazing. C. Pipe Insulation Shall Be Performed Fiberglass Or Its Equivalent. The Insulating Materials Shall Be Covered With 100mm X. 13mm Thick Polyethelene Film, Which Shall Be Overlapped Not Less Than 50mm. D. Ducts Shall Be Galvanized Sheet Steel Of Standard Gauges. E. Ductwork Insulation Materials Shall Be Rigid Board Made Of Styropor Or Equivalent 25mm Thick For Ground And Top Floor, 13mm Thick For Intermediate Floor. -end Of Mechanical Works Design Parameters- Xviii. Design Parameters (electrical/auxiliary Works) A. Codes And Standards The Electrical System Design Parameters Shall Be In Accordance With The Following Codes And Standards.  Codes: 1. Philippine Electrical Code 2. National Electrical Code 3. Fire Code Of The Philippines 4. National Building Code Of The Philippines And Its New Irr 5. Existing Local Codes And Ordinances  Standards: 1. Bureau Of Product Standards (bps) 2. Underwriters Laboratory (ul) 3. National Fire Protection Association 4. International Electrotechnical Commission (iec) 5. Illumination Engineering Society (ies) 6. National Electrical Manufacturer’s Association (nema) 7. Doh Manual On Technical Guidelines For Hospital And Health Facilities Planning And Design B. Building Facilities Electrical System 1. Lighting System  Provide And Install Adequate Normal Branch Circuits For Lighting System To All Areas Using The Standard Lighting Design Analysis. Utilize The Standard Illumination Requirements Per Area Of Concern Using The Preferred Particular Type Of Luminaires. 2. Power System  Provide And Install Adequate Normal Branch Circuits For The Power System. 3. Standby/emergency System  Provide And Install Adequate Life Safety And Critical Emergency Branch Circuits For Lighting Or Utilization Equipment Connected To The Alternate Power Source. 4. Auxiliary System Provide And Install The Following Auxiliary System:  Communication System A. Telephone System B. Local Area Network System C. Public Address Paging System D. Private Branch Exchange (pabx) E. Master Or Cable Antenna Television  Fire Alarm System  Security System 5. Lightning Protection System  The Building Lightning Protection System Shall Include Roof-mounted Air Terminals Grounding Conductors, Ground Rods, Conduits, Clamps, And Auxiliary Equipment As Required For A Complete And Operational Lightning Protection System. 6. Provide Details Of The Following:  Lighting Fixtures/luminaires  Panelboard And Circuit Breakers  Switchgear And Other Metering Devices  Electrical And Hospital Equipment  Installation And Termination Of Auxiliary And Other Special Devices And Equipment  Power And Telephone Handholes (as May Be Required)  Pedestal And Service Entrance To Bldg.  Grounding System Layout  Substation/power House And Electrical Room  Transformer And Generator Mounting  Others As May Be Required. C. Summary Of Materials  General Lighting Luminaries: Fixtures Type Shall Be As Indicated On The Lighting Layout Plan. 1. Fluorescent Lamp Shall Be Linear, Circular Or Self-ballasted Compact Fluorescent Lamps. 2. Fluorescent Lamps Shall Be Cool Or Warm White And 3. Lamp Holders Shall Be Made Of Thermosetting Plastic. 4. Fluorescent Ballast: Magnetic Or Electronic Type With High Power Factor Or High Frequency Energy Saving Type. 5. Fluorescent Fixture Housing Shall Be Steel Sheet With High Reflectance Powder Coat Paint Finish. 6. Downlights And Pin Lights Shall Be Of Heavy Gauge Spun Aluminum Equipped With Lamp As Indicated On The Drawings. 7. Other Special Lighting Requirements Shall Be As Approved By The Implementing Agency. 8. Sterile Areas/zones Lighting Specifications: A. Type: Use Sealed, Recessed, Or Surface-mounted Led Fixtures That Are Flush With The Ceiling Surface To Prevent Dust Accumulation. B. Lux Level: Aim For 300-500 Lux For General Sterile Areas; 1000 Lux Or More May Be Needed In Surgical Suites Or Examination Zones Or As Specified On Manual Of Technical Guidelines For Hospital Planning And Design (level 3)  Wiring Devices: Wiring Devices Shall Be Non-automatic Control Devices, The Contact Is Guaranteed By The Pressure Of The Special Spiral Springs. 1. Switches Shall Be Of 15a, 250v Or 300v Except As Otherwise Noted And Approved. Terminals Shall Be Screw-type Or Quick-connected Type. 2. General Use Receptacle Shall Be 15a, 240v Grounding Type Unless Otherwise Indicated On The Drawings. 3. Special Purpose Receptacles Shall Be As Called For On The Drawings. 4. Matching Plugs Shall Be Supplied.  Panelboards And Circuit Breakers: The Panelboard And Circuit Breakers Shall Be Equipped With Molded-case Circuit Breakers And Shall Be The Type As Indicated In The Panelboard Schedule And Details. 1. Provide Molded-case Circuit Breakers Of Frame, Trip Rating And Interrupting Capacity As Shown On The Drawings. The Circuit Breakers Shall Be Quick-make, Quick Break, Thermal-magnetic, Trip-indicating And Shall Have Common Trip On All Multiple Breakers With Internal Trip Mechanism. 2. All Current-carrying Parts Of The Panelboards Shall Be Plated. Provide Solid Neutral (s/n) Assembly When Required. The Assembly Shall Be Isolated From The Enclosure.  Electrical Conduits, Boxes And Fittings: All Conduits, Boxes And Fittings Shall Be Standard Rigid Steel, Zinc Coated Or Galvanized. 1. Rigid Steel Conduits (rsc) 2. Rigid Metal Conduits (rmc) 3. Intermediate Metal Conduits (imc) 4. Electrical Metallic Tubing (emt) 5. Unplasticized Polyvinyl Chloride (upvc) If Required Shall Be Schedule 40.  Conductors: Wires And Cables Shall Be Of The Approved Type And Unless Specified Or Indicated Otherwise, All Power And Lighting Conductors Shall Be Insulated For 600 Volts. 1. The Conductors Used In The Wiring System Shall Be Of Soft-annealed Copper Having A Conductivity Of Not Less Than 98% Of That Of Pure Copper And Insulated For 60° C Temperatures. 2. All Conduits Of Convenience Outlets And Wire-ways For Lighting Branch Circuit Home-runs Shall Be Wired With A Minimum Of 3.5 Mm Square In Size.  Master Antenna Television (matv) And Cable Television (catv) System: 1. Two Sources Of Tv Signals Shall Be Provided To The Building. One (1) Shall Be From A Master Antenna Installed At The Roof Or Within A Suitable Area Of The Building And The Other Will Be From A Commercial Cable Television Service. 2. The Master Antenna System Shall Consist Of Fm, Vhf And Uhf Antennas, Combiner, Distribution Amplifier, Coaxial Cables, Splitters, Tap-offs And Tv Outlets. 3. There Shall Be Individual Trunking For Master Antenna And Cable Television Rising In The Building.  Structured Cabling & Telephone System: 1. A Minimum Provision For Estimated 500 Mixed Pabx Extension And Direct Telephone Lines Shall Be Required For Tertiary Hospitals. 2. Final Details Of The System Shall Follow Specific Requirements, Quantity And Type Of Service.  Fire Detection And Alarm System: 1. The Fire Detection And Alarm System Shall Be Of Multiplex, Microprocessor- Controlled Addressable Or Zonal Conventional Fire Detection, Alarm And Communication System. 2. The System Shall Consist Of Full Integration Automatic Fire Detection, Voice Alarm Communication And Fire Fighters Telephone System. 3. The System Shall Consist Of Control Station, Mimic Panel Initiating And Indicating Devices, Control Modules And System Of Wirings. 4. Actuation Of The Protective Signaling System Shall Occur By Manual Pull Station, Automatic Smoke Or Heat Detector, Sprinkler Flow Switch And Tamper Switch. 5. The System Shall Be Able To Monitors The Status Of Flow Switches And Supervisory Switches Installed At The Sprinkler System Risers. These Monitoring Points Are Also Addressable Or The Conventional Zonal In The Same Way As The Detectors Are Making Them Easily Recognizable At The Control Panel. 6. Occupant Notification Shall Be Accomplished Automatically. Notification Will Be General, Audible Alarm Type Complying With Appropriate Section Of Nfpa. 7. The System Shall Be Installed With Provisions For Future Connection To The Nearest Fire Services Station In The Locality.  Security System: 1. The Security System Shall Include Intrusion Detection And Alarm, Cctv, Access Control Or As Maybe Required.  Ventilation And Air Conditioning System The Ventilation And Air Conditioning System Shall Be Composed Of Complete Plans And Drawings Of The Following: 1. General Notes, Legends And Symbols Including Schematic Diagram Of The Ventilation And Air Conditioning System. 2. Floor Layout Of The Ventilation And Air Conditioning System Indicating The Capacity And Location Of The Air Conditioners And Fans. 3. Duct Layout Indicating Duct Sizes, Route And Location Of The Dampers, Diffusers, Return Air Register, Hangers And Sway Braces. 4. Refrigerant Piping Layout Indicating Pipe Sizes, Location Of Valves, Hangers And Sway Braces. 5. Equipment Schedule And Details Drawings Of Air Conditioners And Ventilating System. A) Air Conditioning System Shall Be Provided In All Patient’s Private Rooms, Radiologic And Imaging Area, Operating Rooms, Delivery Rooms, Laboratories, Critical Care Areas, Offices And Other Areas Where Conditioned Air Is Necessary. B) Cooling Load Calculations Report Shall Be Manual Or Computer Generated, Hourly Analysis Program Which Includes Heat Transmission Coefficients, Solar Heat Gain Factors And Corrected Cooling Load Temperature Difference Calculations. C) Split Type Air Conditioners Will Be Used At Areas With Larger Capacities. D) Window Type Air Conditioners Shall Be Used In Areas With Exterior Wall Exposure. E) Centralized Air Conditioning Will Be Used Only If Feasible. F) Design Of All Critical Areas Shall Be Laminar Or Positive Pressure, Wherein The Supply Air Is 10% More Than Exhaust Air. G) All Infectious Isolation Rooms, Such As Tb And Sars, Shall Be Negative Pressure, Wherein The Exhaust Air Is More Than 10% Of The Supply Air. H) Maintain An Air Change Rate Greater Than Or Equal To 12 Air Changes Per Hour Or 145 Liters Per Second Per Patient. I) Ceiling Cassette Type Exhaust Fans With Integral Air Diffuser Shall Be Provided In All Toilets. J) Ceiling Fans, Orbit Type With 360° Oscillation Shall Be Provided In All Non-air-conditioned Rooms, Such As Patient Wards, Work Areas, Etc.  Air Conditioning And Refrigeration System 1. Refrigerant Pipes Shall Be Copper Tubing, Type L Or K Black Steel Pipe, Schedule 40 For Size Of 100mm Diameter And Smaller. Pipe Over 100mm Shall Be Black Steel Pipe Schedule 40. 2. Black Steel Pipes Shall Be Standard Seamless, Lap-welded, Or Electric Resistant Welded For Size Of 50mm Diameter And Larger, Screw Type For Size 38mm Diameter And Smaller, Fittings For Copper Tubing Shall Be Cast Bronze Fitting Designed Expressly For Brazing. 3. Pipe Insulation Shall Be Performed Fiberglass Or Its Equivalent. The Insulating Materials Shall Be Covered With 100mm X. 13mm Thick Polyethylene Film, Which Shall Be Overlapped Not Less Than 50mm. 4. Ducts Shall Be Galvanized Sheet Steel Of Standard Gauges. 5. Ductwork Insulation Materials Shall Be Rigid Board Made Of Styropor Or Equivalent 25mm Thick For Ground And Top Floor, 13mm Thick For Intermediate Floor. -end Of Electrical Works Design Parameters- Xix. Design Parameters (green And Safe Health Facilities)  Codes And Standards Green And Safe Health Facilities Shall Be In Accordance With The Following Laws, Codes And Standards.  Global Initiatives & Developments: 1. World Health Assembly Resolution On Universal Health Care (2019) 2. World Health Resolution On Climate Change And Health (2008) 3. Un Resolution On Sustainable Development Goals (2015) 4. Global Action On Patients’ Safety  Laws And Codes: 1. Sanitation Code Of The Philippines Irr Of Chapter Xvii 2. The Local Government Code Of 1991 3. Clean Water Act Of 2004 4. National Building Code Of The Philippines (pd 1096) 5. General Appropriation Act Fiscal Year 2021 (ra 11518) 6. Occupational Safety And Health (ra 11058) 7. Safe Hospital Initiative (2011) 8. Universal Health Care Act (ra 11285) 9. Implementing Rules And Regulations Of Accessibility Law (ra 344) 10. Ecological Solid Waste Management Act Of 2000 (ra 9003) 11. Climate Change Act Of 2009 (ra 9729) 12. Other Related Standards A. Guidelines The Green And Safe Hf Initiative Represents A Climate Smart Paradigm Shift, Away From Traditional Disaster Response To One That Proactively Seeks To Minimize The Health Impact Of Disasters And Emergencies Through Climate Adaptation And Mitigation Measures (including Climate-proofing And Reduction Of The Environmental Footprint), And Preparedness. Consequently, It Is Essential That This Green Manual Is Incorporated Into The Hospital And Hf Development Agenda That Are Backed With Earmarked Resources In The National Budget, And That Has Governance And Support From The Highest Levels Of Government.  The Department Of Health Shall, As Much As Possible, Promote The Greening Of Hospitals And Health Facilities, Including The Improvement Of Energy And Water Efficiency And Conservation, Sustainable Cooling Systems, And Sustainable Healthcare Waste Management In Hospitals.  In Line With Its Continuing Efforts In Green And Safe Hfs, The Doh Shall Encourage National And Local Government Hospitals And Other Hfs To Seek Green Certifications From Green Building Rating System/s For Their New Construction Or Expansion, Repair And Renovation Projects. B. Criteria And Compliance System For Outstanding Green And Safe (climate Smart) Health Facilities.  Criterion Compliance 1. Governance – Leadership And Management, Trainings, Proper Implementation, Commitment 2. Energy Efficiency – Reduction Of Energy Consumption, Use Of Renewable And Clean Energies 3. Water Efficiency, Sanitation And Hygiene – Adequate Water, Water Reuse/recycling, Water Conservation, Rainwater Harvesting. Safe Drinking Water, Proper Use And Maintenance Of Sanitary Toilet Facilities 4. Health Care Waste Management Waste – Segregation, Collection, Storage, Transport, Treatment, Proper Waste Disposal, Recycling 5. Environmentally Resilient Health Facility – Structural Member, Non-structural Member, Emergency And Disaster Preparedness Plan 6. Site Sustainability – Healing Gardens Within, Fresh Air, Herbal Plants, Accessibility, Existence Of Alternative Routes 7. Material Sustainability – Use Of Sustainable Materials, Procurement Of Sustainable And Recyclable Products, Less Use Of Hazardous And Toxic Substances 8. Indoor Environmental Quality – Lighting, Ventilation, Interior Design, Air Quality Management C. Energy Efficiency  Orientate Building & Façade Design To Mitigate Heat Gain. The East And West Facades Receive The Greatest Solar Radiation, And Should Be Designed To Avoid Direct Sun.  Use Of Glass/glazing With A Lower U-value And Shading Coefficient Reduce Solar Heat Gain.  Allow Provision For Easy Access For Maintenance And Cleaning Especially For Curtain Wall System.  Consider Lifespan, Durability And Life Cycle-costing When Selecting Façade Materials.  Install And Use Energy-efficient Lighting Fixtures I.e. Led, Cfl, Slim Type Fluorescent, Etc.  Skylights (if Applicable) And Windows To Maximize Natural Lighting And Ventilation On Selected Areas. Utilizing Daylight As Possible.  Use Of Appliance With Inverter Technology With Variable Frequency Drive Technology.  Window And Door Assemblies Shall Have Complete Gaskets, Weather Stripping, Door Bottom Sweeps And Seals.  All Operable Windows Shall Be Provided With Safety Features For Protection Against Strong Winds, Water Penetration And Protection For Building Occupants Including Child Safety And Security.  Specific Air Exchange Rates Are Usually Attained Through Artificial Ventilation. Adequate Ventilation Throughout The Facility Contributes To Maintaining A Hygienic Environment. Presence Of Functional Windows And Doors, That Allow At Least 6-8 Air Changes Per Hour For Natural Ventilation. For Airborne Infection Isolation Room/s And Er/triage Areas, Greater Or More Than 12 Air Changes Per Hour Is Recommended, While Up To 15 Air Changes Per Hour May Be Recommended For Operating Procedure, Or Delivery Rooms.  Light-colored Building Envelopes Is Also Recommended To Reduce Heat Transfer From The Outside To Inside Of The Building By Having Surfaces With High Solar Reflectance Index (sri). D. Water Efficiency, Sanitation And Hygiene  Optimize Water Conservation Through Installation Of Rainwater Harvesting Cistern Tank  Use Of Waterless Urinals And Dual Flush Water Closets.  Use Of Low-flow & Water Efficient Faucet And Hand-held Bidets.  Use Of Water-saving Shower Heads  For Hospitals, There Must Be At Least One Water Closet For Every Eight Patients In Compliance With Ra 4226 – Hospital Licensure Act.  A Separate Toilet For Male And Female Is Preferred, And Shall Be Pwd Accessible. And, A Separate Toilet For The Staff, With A Provision Of One Toilet For Every Fifteen Personnel Shall Be Applied.  Waterless Urinals Must Be Provided For Male Toilets.  There Should Be Sufficient And Functional Hand-washing Facilities. E. Environmentally Resilient Health Facility  Ground Floor Must Be Above Ground Line And Anticipated Flood Level. F. Material Sustainability  Building Materials, If Applicable, Must Be Locally Sourced To Minimize Carbon Footprint.  Rapidly Renewable And Sustainable Materials Are Also Recommended. Refer To Sec. 16.3.4 Of Doh Green And Safe Health Facilities Manual For List Of Sustainable Construction Materials That Can Be Used.  Use Of Materials (specifically Wet-applied Materials) That Are Low In Vocs (volatile Organic Compounds) G. Site Sustainability  Adopt The Development Controls Indicated In The National Building Code Of The Philippines To Establish The Extent Of The Health Facility Site Can Develop.  Biophilic Design Is Recommended To Help Reduce Stress, Improve Cognitive Function And Creativity, Improve Patients’ Well-being And Expedite Healing.  Porous Pavement Is Recommended At The Site Development To Alleviate Flooding. Landscape Swales Is Also One Solution. H. Indoor Environmental Quality  Harvest Natural Daylight If Applicable.  Acoustic Quality, Especially In Areas/rooms That Needs To Be Soundproofed, Shall Be Maintained.  Use Of Acoustic Privacy Partitions Is Required.  Separate Entrances For Ambulances And Walk-in Patients.  In Procedure Rooms With Windowless Areas, Backlit Photomurals Or Artificially Illuminated Glass Artwork Can Alleviate Feeling Of Claustrophobia.  In Wards And Recovery Rooms, Provide Windows And Natural Illumination As Much As Possible.  Provide Acoustic Privacy In Patient Rooms, Offices, And Examination Rooms With Partitions Of Sound Transmission Class (stc) Of 45.  Noise Level In The Operational Rooms Must Follow The Minimum Noise Standards In Accordance To The Doh Manual Of The Technical Guidelines For Hospital Planning And Design (level 3) Drawing Requirements: See Doh Standard Checklist Based On Revised Irr Of The National Building Code Of The Philippines (pd 1096). Checklist Of Drawing Requirements In The Preparation/evaluation/approval Of Detailed Architectural And Engineering Plans And Other Documents For Infrastructure Project Implementation. -end Of Green And Safe Health Facilities Design Parameters- Xx. Build Aspect Furnish Labour, Materials, Equipment, Paint, Tools And Other Facilities To Complete The Entire Building Including Architectural, Structural/ Civil, Electrical, Mechanical, Sanitary, Communication, Fire Protection, And Other Related Works To Complete The Scope As Specified And/or As Shown On Drawings And Plans 1. General Requirement  Contractor’s Temporary Facility And Lay Down Yard.  Communication And Transmittal, Reproduction, Tarpaulin/billboard And Photos  Material Testing (rsb, Chb, Concrete, Steel)  Safety Requirements (warning Signs, Hardhat, Etc.)  As Built Plan  Demolition, Clearing Work, Permits And Licenses 2. Other Items Of Work  Demolition Of Existing Structures In Affected Areas Or Where The Proposed Project Shall Be Situated, Clearing And Disposal Of All Debris Generated During Construction.  All Serviceable Materials Shall Be Turn Over To Doh-dedvmh Through Its Representative  Soil Excavation And Soil Treatment  Restoration Of Any Damaged Properties During The Construction  Permit Fees, And Other Necessary Documents For The Project Shall Be Shouldered By The Contractor  Temporary Facilities Shall Be Provided During The Construction Period, To Be Constructed Within The Hospital Compound, Which Shall Serve As The Field Office, Storage Of Materials And Bunkhouse For The Workers.  No Implementation Of The Project Without An Approved Plan And Other Related Documents.  Strict Implementation Of (dole Guidelines And Other Standards Applicable) Health And Safety Rules.  Shall Abide By The Medical Center Hospital House Rules  Conduct Weekly Progress And Coordinative Report To The Agency Or Its Representative  Other Items Of Work Not Mentioned Herewith But It Is Very Necessary For Execution And Completion Or Works Shall Be Included And Charge To The Contractor 3. Pre-installation Requirements  All Tests To Be Conducted Shall Be Witnessed By The Hospital Representatives.  Soil Investigation  Concrete Strength Testing  Reinforcing Bar Strength Testing  Concrete Masonry Unit (cmu) Testing  All Plumbing And Sanitary System  Automatic Fire Sprinkler System  Ventilation And Air Conditioning System  All Electrical System  And Other Tests That Necessary To Perform To Ensure The Quality Of The Project  All Certifications And Reports Under Post-installation Requirement Shall Be Submitted To The Hospital Representatives.  The Contractor Shall Submit A Sample Of Materials For Approval Of The Medical Center Chief Prior To Installation.  No Implementation Or Execution Of Work In Any Discipline Without The Approval Of Medical Center Chief Or Through Its Representative  Any Request For Inspection, Approval, Concrete Pouring, Testing And Commissioning Must Be Address To Medical Center Chief Or Must Adhere To The Reporting Protocol As Mentioned Above. -end Of Build Aspect- Checklist Of Drawing Requirements In The Preparation/evaluation/approval Of Detailed Architectural And Engineering Plans And Other Documents For Infrastructure Project Implementation Reference: Revised Implementing Rules And Regulations Of The National Building Code Of The Philippines (pd 1096) Project : Location : Sheet Number Sheet Contents Remarks* Architectural Drawings (as Applicable) A – 1 (a…n) Perspective, Site Development Plan, Vicinity Map/location Plan (2.00 Kms. Radius) Table Of Contents A – 2 (a…n) Floor Plans (scale 1:100m Minimum) Including Furniture Layout When Necessary A – 3 (a…n) Four (4) Elevations (scale 1:100m Minimum) A – 4 (a…n) Two (2) Sections (scale 1:100m Minimum) Including Spot Details When Necessary A – 5 (a…n) Roof Plan/s Showing Downspouts (scale 1:100m Minimum), Including Detail Of Gutter, Downspout, Etc. A – 6 (a…n) Reflected Ceiling Plan/s (scale 1:100m Minimum), Including Details A – 7 (a…n) Details Of Stairs, Fire Escapes/exits, Accessible Ramps, Etc. (scale 1:50m), Including Details Of Railings, Treads, Risers, Etc., In The Form Of Plans, Elevation/section A – 8 (a…n) Details Of Toilets (1:50 M) Including Accessible Toilets In The Form Of Plans, Elevation/section A – 9 (a…n) Details Of Specialized Design Features (scale 1:50 M) Such As Partitions, Cabinets, Etc. And Accessible Design Features A – 10 (a…n) Detail Of Typical Bay Section From Ground To Roof (scale 1:50 M) A – 11 (a…n) Details Of Special Elevations/section Rooms (1:50m) In Form Of Plans, A – 12 (a…n) Schedule Of Doors, Gates, Emergency Exits, Etc. (scale 1:50 M), Including Specifications For Materials And Hardware A – 13 (a…n) Schedule Of Windows (scale 1:50 M), Including Specifications For Materials And Hardware A – 14 (a…n) Schedule Of Finishes For Interior And Exterior Floors, Walls, Ceilings Architectural Technical Specifications Architectural Scope Of Works Architectural Bill Of Quantities * To Be Marked As Either Complying Or Non-complying/complete Or Incomplete By The Evaluator Or To Be Filled With Supporting Comments (use Additional Sheets If Necessary) Evaluated By: ____________________________________________________________ Page 1 Of 6 Checklist Of Drawing Requirements In The Preparation/evaluation/approval Of Detailed Architectural And Engineering Plans And Other Documents For Infrastructure Project Implementation Reference: Revised Implementing Rules And Regulations Of The National Building Code Of The Philippines (pd 1096) Project : Location : Sheet Number Sheet Contents Remarks* Architectural Interior Design Drawings (as Applicable) Aid – 1 (a…n) Floor Plans Showing Layout Of Floor Finishes (scale 1:100m Minimum) Aid – 2 (a…n) Floor Plans Showing Layout Of Furniture/finishing Partitions, Cabinets, Etc. (scale 1:100m Minimum) Aid – 3 (a…n) Interior Elevations And Sections Showing Wall Patterns, Ceiling Sections, Etc. (scale 1:100m Minimum) Aid – 4 (a…n) Details Of Partitions, Cabinets, Furniture, Ceiling And Other Interior Design Features (scale 1:100m Minimum) Aid – 5 (a…n) Architectural Interior Perspective/s Architectural Interior Design Technical Specifications Architectural Interior Design Scope Of Works Architectural Interior Design Bill Of Quantities * To Be Marked As Either Complying Or Non-complying/complete Or Incomplete By The Evaluator Or To Be Filled With Supporting Comments (use Additional Sheets If Necessary) Evaluated By: ____________________________________________________________ Page 2 Of 6 Checklist Of Drawing Requirements In The Preparation/evaluation/approval Of Detailed Architectural And Engineering Plans And Other Documents For Infrastructure Project Implementation Reference: Revised Implementing Rules And Regulations Of The National Building Code Of The Philippines (pd 1096) Project : Location : Sheet Number Sheet Contents Remarks* Structural Drawings (as Applicable) S – 1 (a…n) General Notes And Construction Standards S – 2 (a…n) Site Development Plan S – 3 (a…n) Foundation Plan/s (scale 1:100m Minimum) S – 4 (a…n) Floor Framing Plan/s (scale 1:100m Minimum) S – 5 (a…n) Roof Framing Plan (scale 1:100m Minimum) S – 6 (a…n) Schedule And Detail Of Footings And Columns S – 7 (a…n) Schedule And Detail Of Beams And Floor Slabs S – 8 (a…n) Detail Of Trusses S – 9 (a…n) Details Of Stairs, Ramps, Fire Exits S – 10 (a…n) Other Spot Details Structural Analysis And Design (for 2 Storey Building And Higher) Boring And Land Test Results (for 3 Storey Building And Higher) Seismic Analysis Structural Technical Specifications Structural Scope Of Works Structural Bill Of Quantities * To Be Marked As Either Complying Or Non-complying/complete Or Incomplete By The Evaluator Or To Be Filled With Supporting Comments (use Additional Sheets If Necessary) Evaluated By: ____________________________________________________________ Page 3 Of 6 Checklist Of Drawing Requirements In The Preparation/evaluation/approval Of Detailed Architectural And Engineering Plans And Other Documents For Infrastructure Project Implementation Reference: Revised Implementing Rules And Regulations Of The National Building Code Of The Philippines (pd 1096) Project : Location : Sheet Number Sheet Contents Remarks* Electrical Drawings (as Applicable) E – 1 (a…n) General Notes And Legends E – 2 (a…n) Location And Site Plan E – 3 (a…n) Lighting Layout (scale 1:100m Minimum) Including Details E – 4 (a…n) Power Layout (scale 1:100m Minimum) Including Details E – 5 (a…n) Auxiliary System Layout (scale 1:100m Minimum) Including E – 6 (a…n) Schedule And Detail Of Loads E – 7 (a…n) Riser Diagram E – 8 (a…n) Other Detail Electrical Computation Design Analysis Electrical Technical Specifications Electrical Scope Of Works Electrical Bill Of Quantities * To Be Marked As Either Complying Or Non-complying/complete Or Incomplete By The Evaluator Or To Be Filled With Supporting Comments (use Additional Sheets If Necessary) Evaluated By: ____________________________________________________________ Page 4 Of 6 Electronics/auxiliary System Ready For Integrated Communications 1. Telephone System 2. Paging System 3. Lan System 4. Fire Alarm System 5. Security System Cctv 6. Integrated Communications And Systems Checklist Of Drawing Requirements In The Preparation/evaluation/approval Of Detailed Architectural And Engineering Plans And Other Documents For Infrastructure Project Implementation Reference: Revised Implementing Rules And Regulations Of The National Building Code Of The Philippines (pd 1096) Project : Location : Sheet Number Sheet Contents Remarks* Plumbing/sanitary Drawings (as Applicable) P – 1 (a…n) General Notes And Legends P – 2 (a…n) Location And Site Plan P – 3 (a…n) Storm Drainage Layout (scale 1:100m Minimum) Including Actual Length Of Tapping Line To Main Drainage Line P – 4 (a…n) Waterline Layout (scale 1:100m Minimum) Including Actual Length Of Tapping Line From Main Water Source When Applicable P – 5 (a…n) Sewerline Layout (scale 1:100m Minimum) Including Actual Length Of Tapping Line To Septic Tank Or Existing Sewerline P – 6 (a…n) Isometric Layout, Showing Waterline, Sewerline And Drainage Line P – 7 (a…n) Detail Of Connections, Catch Basins, Downspouts, Etc. P – 8 (a…n) Detail Of Septic Tank/sewer Treatment Plant Design Analysis Sanitary Technical Specifications Sanitary Scope Of Works Sanitary Bill Of Quantities * To Be Marked As Either Complying Or Non-complying/complete Or Incomplete By The Evaluator Or To Be Filled With Supporting Comments (use Additional Sheets If Necessary) Evaluated By: ____________________________________________________________ Page 5 Of 6 Checklist Of Drawing Requirements In The Preparation/evaluation/approval Of Detailed Architectural And Engineering Plans And Other Documents For Infrastructure Project Implementation Reference: Revised Implementing Rules And Regulations Of The National Building Code Of The Philippines (pd 1096) Project : Location : Sheet Number Sheet Contents Remarks* Mechanical Drawings (as Applicable) M – 1 (a…n) General Notes And Legends, Site Development Plan, Location Plans M – 2 (a…n) Floor Plans/isometric Drawings (scale 1:100m Minimum) Showing Ventilation And Air Conditioning Systems And Other Installations M – 3 (a…n) Floor Plans/isometric Drawings (scale 1:100m Minimum) Of Gas Pipeline System And Details M – 4 (a…n) Floor Plans/isometric Drawings (scale 1:100m Minimum) Of Air-conditioning Systems And Details M – 5 (a…n) Floor Plans/isometric Drawings (scale 1:100m Minimum) Of Fire Suppression Systems, Fire Sprinkler System, Wet Stand Pipe, Dry Standpipe And Other Installation M – 6 (a…n) Details Water Tank, Flow Diagram (scale 1:50m) M – 7 (a…n) Details Of Firewater Supply Sytem (scale 1:50m) M – 8 (a…n) Detail Of Elevators, Escalators, Dumbwaiters, Etc. (scale 1:50m) M – 9 (a…n) Detail Of Other Machinery/equipment (scale 1:50) M – 10 (a…n) Longitudinal And Transverse Section Of Building (scale 1:100m) Showing Manner Of Support Of Machines/equipment Mechanical Technical Specifications Mechanical Scope Of Works Mechanical Bill Of Quantities * To Be Marked As Either Complying Or Non-complying/complete Or Incomplete By The Evaluator Or To Be Filled With Supporting Comments (use Additional Sheets If Necessary) Evaluated By: ____________________________________________________________ Page 6 Of 6 General Guidelines • All Construction Works Shall Be Undertaken By Contractor In Accordance With Existing Laws And All Other Applicable Rules And Regulations. • The Contractor Shall Be Responsible In Setting Out Reference Lines, Elevations (lines And Grades) Prior And During The Execution Of The Works. All References Shall Be Maintained And Protected By The Contractor At His Own Expense. Disturbed References Shall Be Restored To Its Original Position Without Extra Cost To Devmh. • The Contractor Shall Carry Out The Works Properly And In Accordance With This Contract. The Contractor Shall Provide All Supervision, Labor, Materials, Plant And Equipment, Which May Be Required. • The Contractor Shall Commence Execution Of The Works On The Start Date And Shall Carry Out The Works In Accordance With The Approved Pert/cpm Network Diagram Submitted By The Contractor, As Updated With The Approval Of The Procuring Entity’s Representative, And Shall Complete The Works By The Intended Completion Date. • The Contractor Shall Be Responsible For The Safety Of All Activities On The Site. • During On-going Construction And Before The Turn-over Of The Project, Engineering & Facilities Management Staff, End-users, Twg And Bac Shall Inspect The Works Undertaken By Contractor. Hospital Engineers And End-users Discover Any Deviations By Contractor From The Approved Construction Plans, Contractor Shall Be Required To Rectify All Such Deviations, Within Such Period Required By Client. • Contractor Shall Have Full Responsibility For Any And All Damages To Existing Hospital Facilities, Utilities, And/or Any Portion Of The Hospital’s Common Area, Due To The Works Undertaken By Contractor, Whether Accidental Or Intentional. • No Variation Order Shall Be Undertaken Unless Verified By Hospital Engineer And Approved By Executive Committee. • Contractor Shall Not Cover Or Block Stub-outs (cleanouts, Water Source, Exhaust, Sewer, Drainage, Etc.) When Not Utilized. Said Stub-outs Shall At All Times Be Free Of Obstructions And Easily Accessible. • Contractor Shall Secure A Utility Tapping Permit Prior To Tapping From Utility Provision. • Electricity And Water Consumed During Construction Shall Be Charged To Contractor. • End-users Reserves The Right To Inspect The Works At Any Time. • Contractor Shall Insure And Hold Client, Its Affiliates, Officers, Directors, Stockholders, Employees, Agents, And/or Representatives, Free And Harmless From And Against Any Injury, Losses, Claims, Damages, Liabilities, Expenses, And/or Costs Of Litigation, Resulting From Or Arising Out Of The Works Undertaken By Contractor. • In Event Of Force Majeure, The Contractor Shall Rectify, Replace Or Build The Unfinished Projects When It Is Not Yet Completed And Accepted W/o Additional Cost For The Procuring Entity. • Contractor Shall Comply With The Construction House Rules Of This Hospital.

Details: Description Invitation To Bid Project No: 005 – 2025 - Rb 1. The Department Of Education Through The Fy 2025 Gaa Intends To Apply The Sum Of Seven Million Three Hundred Thirty-eight Thousand Five Hundred Seven And 00/100 (7,338,507.00) Being The Approved Budget For The Contract (abc) For Lots 1 And 2 For The Procurement Of Assistive Devices, Equipment, Supplies And Materials For Inclusive Learning Resource Centers. Bids Received In Excess Of Abc Shall Be Automatically Rejected At The Bid Opening. Unit Description Qty Cost Abc (vat Inclusive) 1 Lot Procurement Of Assessment Tools For Inclusive Learning Resource Centers 1 Set Adaptive Behavior Scale (specs: Vineland-3; Manual; Interview Form, Teacher Form, Parent Form 1 40,000.00 40,000.00 2 Set Autism Checklist (specs: Childhood Autism Rating Scale For 2 Yrs Old And Above: 1manual,25 Standard Rating Booklet,25 High Functioning Rating Booklet For Parents And Caregivers) 1 35,000.00 35,000.00 3 Piece Intelligence Test Booklet (specs: Raven's Standard Intelligence Test For 12 Yrs Old And Above) 10 3,500.00 35,000.00 4 Set Non-verbal Intelligence Test (specs: Raven’s Colored Intelligence Test For 4-11 Yrs Old: 1 Manual, 1 Test Booklet, Answer Key) 1 49,900.00 49,900.00 5 Set Non-verbal Intelligence Test (specs: Raven’s Standard Intelligence Test For 12 Yrs Old And Above: 1 Manual, 1 Test Booklet, Answer Key) 1 49,900.00 49,900.00 6 Set Psychomotor Speed, Visual Search And Sequencing, And Attention Test (specs: Comprehensive Trail-making Test: 1 Manual, 10 Record Booklets, And A Storage Box) 1 20,000.00 20,000.00 7 Set Trauma And Posttraumatic Stress In Children Test (trauma Symptom Checklist By Dr. John Briere For 8-17 Yrs Old: 25 Piece. Screening Form And Technical Paper 1 12,000.00 12,000.00 8 Set Verbal Intelligence Test (specs: Slosson Intelligence Test For 5 Yrs Old And Above: 1 Manual, 25 Score Sheets And Stimulus Item For The Blind) 1 35,000.00 35,000.00 9 Set Verbal Intelligence Test Score Sheets (specs: Slosson Intelligence Test For 5 Yrs Old And Above: 25 Piece) 1 12,200.00 12,200.00 With License Delivery Terms: Within 30 Days Drop Off Points: General Santos City Sped Integrated School – Quezon Avenue, Brgy. West, Gsc (ilrc) Payment Terms: Payment To The Service Provider Shall Be Made Through Philippine Veterans Bank Lddap-ada / Mds. In The Case Of Accounts Maintained In Other Bank, Bank Transfer Fees Shall Be Chargeable Against The Creditor’s Account. Subtotal P 289,000.00 2 Lot Procurement Of Assistive Devices, Equipment, Supplies And Materials For Inclusive Learning Resource Centers 1 Unit 2hp Split Type Aircon, Inverter (free Installation) At Least 2 Years Warranty After Sales Service 1 49,000.00 49,000.00 2 Piece 8.1cu. Ft. Bottom Freezer Inverter Ref (specs: Net Weight 66kg, Net Dimension 23.6x72.8x26.8 Inches, Color White) At Least 2 Years Warranty After Sales Service 1 30,000.00 30,000.00 3 Unit Android Smart Television 55" 4k Uhd Bluetooth Connectivity, Mobile Screen Mirroring, Netflix, Wireless Connectivity, Youtube Audio Out (mini Jack), Component In (y/pb/pr), Composite In (av), Ethernet (lan), Hdmi, 220v Free Installation At Least 1 Year Warranty With After Sales Service 4 35,000.00 140,000.00 4 Set Cctv - 16ch-dvr 8 Irpf Bullet Camera 8 Irpf Dome Camera 16 Rolls (20meters) Siamese Cables, 35-bng 20-male Head 12v20a18ch Centralized Power Supply Free Installation At Least 1 Year Warranty With After Sales Service 1 49,000.00 49,000.00 5 Piece Solid Top Chest Freezer, 22 Cubic Ft. 355watts, Hxwxd (91cmx198cmx73cm) Dual Function Freezer And Chiller, Roller Feet Galvanized Inner Lining, 2-basket, 2-grip Handles At Least 1 Year Warranty With After Sales Service 1 40,000.00 40,000.00 6 Piece Vacuum Cleaner (heavy Duty Gas 12-25 Pl Wet And Dry Vacuum Cleaner/ Extractor With Power Socket System 1,250 W Weight-9kg, Max Input Power- 1,250 W, Max Vacuum Power-200 Mbar) At Least 1 Year Warranty With After Sales Service 4 12,000.00 48,000.00 7 Piece Washing Machine. 10.5 Kg Digital Inverter Fully Automatic Front Load Washing Machine (total Capacity: 10.5kg Rated Washing Power: Water Pressure: 0.02-1 Mpa Spin Speed: 1400 Rpm Gross Weight: 67 Kg Warranty: 1 Year Parts & Labor / 10 Year Motor Dimension (wxdxh): 595mm X 520mm X 850mm At Least 1 Year Warranty With After Sales Service 1 30,000.00 30,000.00 8 Piece Water Dispenser. Hot And Cold Water/drinking Household Multifunctional Top Loading. Stainless Steel Casing Color White. Dimension: 85x29x29 Cm. Large Bottom Locker. At Least 1 Year Warranty With After Sales Service 9 8,000.00 72,000.00 9 Unit 1500va Ups (black) Input Voltage: 220vac Frequency: 50hz – 60hz, Output Voltage: 220vac Capacity Va/wattage: 1500va/1050watts Transfer Time: ≤10ms Including Direction Time At Least 1 Year Warranty With After Sales Service 2 4,000.00 8,000.00 10 Set All In One Personal Desktop Computer 23" Display Monitor Processor: 2.5 To 3.8 Ghz Ram Memory: 16 Gb Storage: 1 Tb Ssd Wifi Ready, Hdmi, Usb 2.0 Or 3.2 Slots With Graphics Card For Editing Photos And Videos, With Mouse, Mousepad And Keyboard At Least 1 Year Warranty With After Sales Service 3 49,500.00 148,500.00 11 Piece Laptop - 16"-17"" Monitor Processor: 2.5 Ghz To 3.5 Ghz Ram: 16gb Storage: 1tb Ssd With Graphics Card With Bag, Mouse, And Mouse Pad At Least 1 Year Warranty With After Sales Service 13 49,000.00 637,000.00 12 Unit Svc 1500w Automatic Voltage Regulator1500va Avrservo Motor Typeinput Voltage: 140v-260vacoutput Voltage : 110v/220v Output Overvoltage : 246±4voutput Voltage Precision : <±4% Frequency : 50/60hz Temperature Rise : <80k Efficiency : >92%regulation Time : <1s(when Variation Of Input Voltage Is 10%) At Least 1 Year Warranty With After Sales Service 1 4,000.00 4,000.00 13 Unit Svc 3000w Automatic Voltage Regulator 3000va Avr Servo Motor Type Input Voltage : 140v-260vac Output Voltage : 110v/220v Output Overvoltage : 246±4v Output Voltage Precision : <±4% Frequency : 50/60hz Temperature Rise : <80k Efficiency : >92% Regulation Time : <1s(when Variation Of Input Voltage Is 10%) At Least 1 Year Warranty With After Sales Service 1 5,000.00 5,000.00 14 Unit 3in1 Printer (print, Scan, Copy) Dye Ink, A4 (black / Color) (cyan, Magenta, Yellow) Paper Sizes: Legal (8.5 X 14"), Indian-legal (215 X 345 Mm), 8.5 X 13", Letter, A4, 16k (195 X 270 Mm), B5, A5, B6, A6, Hagaki (100 X 148 Mm), 5 X 7", 5 X 8", 4 X 6", Envelopes: #10, Dl, C6 Maximum Paper Size: 215.9 X 1200 Mm Dimensions (w X D X H): 375 X 347 X 179mm, Weight: 3.9 Kg Ac 220-240 V, 50-60 Hz, Usb 2.0 At Least 1 Year Warranty With After Sales Service 8 15,000.00 120,000.00 15 Bottle Printer Dye Ink Color Black 65 Ml 50 300.00 15,000.00 16 Bottle Printer Dye Ink Color Cyan 65 Ml 50 300.00 15,000.00 17 Bottle Printer Dye Ink Color Magenta 65 Ml 50 300.00 15,000.00 18 Bottle Printer Dye Ink Color Yellow 65 Ml 50 300.00 15,000.00 19 Unit A3 Size Ink Tank Printer, Inkjet, 30ppm 4 Colors (cyan, Magenta, Yellow, Black) Integrated Ink Tank System, Usb 2.0 Paper Size: A3 (297mm X 420mm), A4 (210mm X 297mm), A5 (148mm X 210mm), A6 (105mm X 148mm) Resolution: 1400dpi At Least 1 Year Warranty With After Sales Service 1 30,000.00 30,000.00 20 Bottle Sublimation Ink - 100ml (black) 10 350.00 3,500.00 21 Bottle Sublimation Ink - 100ml (cyan) 10 350.00 3,500.00 22 Bottle Sublimation Ink - 100ml (light Cyan) 10 350.00 3,500.00 23 Bottle Sublimation Ink - 100ml (light Magenta) 10 350.00 3,500.00 24 Bottle Sublimation Ink - 100ml (magenta) 10 350.00 3,500.00 25 Bottle Sublimation Ink - 100ml (yellow) 10 350.00 3,500.00 26 Unit Laser Printer Compact Mono Laser Multi-function Laser Printer A4 Print Speed Up To 34 Ppm (black) Wifi, Airprint, Mopria, Wifi Direct, Lan, Usb 2.0 Full Capacity Toner Included. Yield Up To 1200 Pages (black)* Auto 2-sided (duplex) Printing, 50 Sheets Auto-document Feeder (adf), 2-line Lcd Dimensions: 410 Mm × 399 Mm × 319 Mm Up To 250 Sheets Of 80 Gsm Plain Paper Paper Size: A4, Letter, B5 (jis), B5 (iso), A5, A5 (long Edge), B6 (jis), A6, Executive, 16k (195x270 Mm), A4 Short (270mm Paper), Com-10, Dl, C5, Monarch, Legal And Folio At Least 1 Year Warranty With After Sales Service 1 16,000.00 16,000.00 27 Piece Toner Ink For Laser Printer Color Black 10 2,500.00 25,000.00 28 Unit Wireless Printer 6 Colors (cyan, Light Cyan, Magenta, Light Magenta, Yellow, Black) Printing Technology: Micropiezo Printhead Pvc/id Card Printing: Yes Printer Borderless 300 Gsm Wi-fi A4 (210mm X 297mm) Usb: Usb 2.0 Network: Wi-fi Ieee 802.11b/g/n, Wi-fi Direct Network Protocol: Tcp/ipv4, Tcp/ipv6 Network Management Protocols: Snmp, Http, Dhcp, Apipa, Ping, Ddns, Mdns, Slp, Wsd, Lltd Compact Integrated Tank Design Replaceable Maintenance Box High Yield Ink Bottles Ultra-high Page Yield Of 2,100 Pages (colour) Rated Voltage: Ac 220-240 V Rated Frequency: 50 - 60 Hz, Operating: 19 At Least 1 Year Warranty With After Sales Service 1 23,000.00 23,000.00 29 Bottle Universal Pigment Ink - 1liter (black) 2 1,500.00 3,000.00 30 Bottle Universal Pigment Ink - 1liter (cyan) 2 1,500.00 3,000.00 31 Bottle Universal Pigment Ink - 1liter (light Cyan) 2 1,500.00 3,000.00 32 Bottle Universal Pigment Ink - 1liter (light Magenta) 2 1,500.00 3,000.00 33 Bottle Universal Pigment Ink - 1liter (magenta) 2 1,500.00 3,000.00 34 Bottle Universal Pigment Ink - 1liter (yellow) 2 1,500.00 3,000.00 35 Unit Photocopier 28 Copies Per Minute Direct Usb Printing/scanning Copier/printer/colored Scanner Enlarger/reducer Automatic Back-to-back/duplex Printing Touchscreen Operating Panel Original Size Up To 11x17 A3 At Least 1 Year Warranty With After Sales Service 1 49,200.00 49,200.00 36 Piece Toner Ink For Photocopier 20 1,800.00 36,000.00 37 Piece A3/a4 Laminator Machine Hot/cold/reverse 220v Heavy Duty Product Size: 450*175*92mm Product Weight: About 4.5kg Temperature Range: 80-180℃ Film Thickness: ≤1mm Over-plastic Width: ≤330mm At Least 1 Year Warranty 3 5,000.00 15,000.00 38 Unit A4/a3 Sliding Paper Cutter Heavy Duty Metal Base Paper Trimmer For Photo/vinyl/card Rolling Blade Dimensions: 441mm X 169mm (a4) / 580mm X 169mm (a3) Maximum Cutting Width: 318mm (a4) / 450mm (a3) Materials: Aluminum Alloy, High-carbon Steel, Plastic Maximum Sheets Per Cut: 10 Sheets Of 70g Standard Copy Paper At Least 1 Year Warranty With After Sales Service 2 2,000.00 4,000.00 39 Unit Electric Paper Shredder Machine Automatic Heavy Duty Black Paper Cutter Shredder, Weight:17.55kg Size & Spec.: Shred Capacity: 16 Sheets; Shred Size: 4x40mm; Security Level:4 Can Shred: Cd/dvd, Paper, Card, Paper Clip, Staple Continuous Run Time: 30min, Bin Capacity: 31l Machine Noise: 58db Machine Power: 240w, Dimensions:390x302x615mm At Least 1 Year Warranty With After Sales Service 2 20,000.00 40,000.00 40 Piece Portable Sound System With Microphone ( Active Potable Trolley Speaker , 600w Max Power, Bluetooth + Tws, Usb & Sd Playback, Fm Radio, Line-in & Line -out, 2 Guitar Input, 2 Wired Mic Input, 180 Channels, Mic Priority, High Quality Lead Acid 12ah Battery, 12 Dc Input, Dimensions: (l) 36.5cm (w) 40 Cm (h) 67.5 Cm, 2 Fee Wireless Mic) At Least 1 Year Warranty With After Sales Service 2 20,000.00 40,000.00 41 Unit Price Labeler Size & Spec.: 230x130x55mm, With Ink Wheel And Price Label Sticker Color: Black, Material: Abs 1 1,500.00 1,500.00 42 Unit A3 Size Heavy Duty Digital Heat Press Machine 15x18 Inches Flatbed Auto-open Drawer Type *auto-open Heat Press *15x17.75inches Flatbed Working Area *watts: 1800 Watts At Least 1 Year Warranty With After Sales Service 1 20,000.00 20,000.00 43 Unit Cap Press Machine For Sublimation Printing Watts: 450 Press Handle Digital Controller Aluminum Heating Plate Pressure Knob At Least 1 Year Warranty With After Sales Service 1 6,000.00 6,000.00 44 Unit Digital Mug Press Heavy Duty, 220volts, 280watts 11oz Built In Heating Pad Replaceable Heating Pad At Least 1 Year Warranty With After Sales Service 2 6,000.00 12,000.00 45 Piece Acoustic Guitar, Glossy Finish, Body Shape: Redondo Scale Length: 25.6" No. Of Frets: 20, Fret Size: 2.4mm Material Made: Bod, Back & Neck (mahogany) Fingerboard Radius: 15.75", Nut Width: 1.69" With Pickup Tuner And Preamp System Electronics: Controls Volume, Bass, Treble 3 6,050.00 18,150.00 46 Unit Brailler Machine - Metal Carrying Handle Paper Size Maximum: 11.5 X 14 In (29.2 X 35.6 Cm) Weight: 10.6 Lb (4.8 Kg), Recommended Paper Weight: 90 Lb Includes Leather Dust Cover, Audible Bell Sound Seven Spaces Before End Of Line Dot Height: .019 In (.5 Mm), Dot Diameter: .057 (1.4 Mm) Dot Spacing: .09 In (2.3 Mm), Character Spacing: .24 In (6 Mm) Line Spacing: .4 In (10 Mm) 3 49,500.00 148,500.00 47 Unit Mirrorless Camera With Rf-s 18-45mm F/4.5-6.3 Is Stm Lens Kit 24.2mp Aps-c Cmos Sensor Digic X Image Processor Uhd 4k 30p Video Recording Dual Pixel Cmos Af Ii With 651 Points 2.36m-dot Electronic Viewfinder 3.0"" 1.62m-dot Vari-angle Touchscreen 15 Fps Electronic Shutter Movie For Close-up Demos Mode Vertical Movie Mode, Multi-function Shoe, Wi-fi & Bluetooth At Least 1 Year Warranty With After Sales Service 1 49,000.00 49,000.00 48 Unit 18-35mm F/1.8 Dc Hsm Art Lens Dimensions (diameter × Length): Φ78mm × 121mm / Φ3.1in. × 4.8") Weight:810g / 28.6oz. Petal Type Lens Hood Lh780-06 Front Cap Lcf-72mm Iii, Rear Cap Lcr Ii 1 40,000.00 40,000.00 49 Set Speedlite Flash Ttl For Camera Built-in 2.4ghz X Wireless Radio System Compatible With Canon E-ttl / E-ttl Ii Guide Number: 118' At Iso 100 And 105mm Zoom Range: 24-105mm (14mm With Panel) Tilts From -7 To 90°, Rotates 270° Wireless Master/slave Ttl Functionality Recycle Time: 0.1-2.2 Second At Least 1 Year Warranty With After Sales Service 1 5,000.00 5,000.00 50 Unit Portable Camera Tripod (heavy Duty Aluminum) 22lbs Load 67”/1.7m With Detachable Monopod For Dslr, Military Magnesium Aluminum Alloy, Corrosion Resistance Weight: 1.5kg, 28mm Metal Ball Head, 360 Degrees Rotation 5 Sections Tube Leg, Max Diameter: 25mm Height Without Column: 51", Height With 2 Sections Center Column: 67" 1 5,000.00 5,000.00 51 Unit 2.4ghz Wireless Microphone System Transmitter 2.4ghz Frequency Hopping System 200meters Wireless Range Lithium Battery Parameters: 3.7v ⎓ 140mah, 0.518wh 24h All Day Recording Intelligent Noise Cancellation Dynamic Range:86db, Type-c Input, Net Weight: 12g Dimensions: 48mmx22mmx16mm (1.89”x0.87”x0.63”) At Least 1 Year Warranty With After Sales Service 1 3,000.00 3,000.00 52 Unit 2.4ghz Wireless Microphone System Receiver 2.4ghz Frequency Hopping System 200meters Wireless Range, Type-c Input Lithium Battery Parameters: 3.8v ⎓ 200mah, 0.76wh, 5v ⎓ 200ma Dimensions: 48mmx28mmx15mm (1.89”x1.10”x0.59”) Net Weight: 16g At Least 1 Year Warranty With After Sales Service 2 3,000.00 6,000.00 53 Unit Studio Lighting Softbox 50 * 70cm With 2m Light Stand And 45w Light Bulb Max Height: 200cm / 78" Collapsible Height: 65cm / 32" 2 1,500.00 3,000.00 54 Unit 16port Desktop/rackmount Switch Network Switch Hub 16 Port 1 4,000.00 4,000.00 55 Unit 4k Hdmi To Hdmi Wire (10 Meters) 9 1,000.00 9,000.00 56 Unit Audio Voice Recorder. Built-in 375mah Battery, Specification: Recording Time: 512kbps， 32gb: About 144 Hours. Storage Media: Tf Card, 32gb, Battery Capacity: 375mah, Package Size: 15.2x7.8x3.7cm/5.9x3x1.4in, Package Weight: 135g/4.7oz At Least 1 Year Warranty With After Sales Service 3 2,674.00 8,022.00 57 Piece Calculator. Basic Calculator Big Calculator. Office Supplies. Dimension: 160.4x164.5x44.2mm. Color White. Dual Power Supply. Aaa Battery With Solar Panel. Inner Concave Buttons. 10 500.00 5,000.00 58 Box Cat5e, Utp Cable, Box ~305mtrs, Pn: 25awg (lan Cable) 2 6,000.00 12,000.00 59 Unit Dual Band Wifi 6 Router Dimensions Wxdxh: - 10.2 × 5.3 ×1.5 In (260.2 × 135.0 × 38.6 Mm) 2 3,000.00 6,000.00 60 Set Heavy Duty 3.5mm Jack Plug Male To 2 Rca Stereo Aux Audio Cable Line, 10 Meters 9 900.00 8,100.00 61 Unit Network Cable Tester Rj45 Rj11 Rj45 Network Lan Ethernet & Networking Tool Network Repair Dimensions: 10cm*5cm*3cm Two Power Supply Methods: 9v Battery & Type-c Charging 2 600.00 1,200.00 62 Piece Offline Mini Compressor (air Compressor Kwv550 9l) 1 4,558.00 4,558.00 63 Piece Presentation Clicker. Slide Deck Presentation 2.4ghz Wireless Usb Ppt Flip Pen Pointer Clicker Presenter With Red Light Remote Control, Color Black 9 900.00 8,100.00 64 Unit Rj45 Crimping Tool Ethernet Network Lan Cable Crimper Cutter Stripper Plier Modular 8p Rj45 And 6p Rj12 Rj11 2 400.00 800.00 65 Unit Usb Headset Headphone With Noise Cancelling, Unidirectional Microphone, Wired Connection Cable Length: 200 Cm, Port: Usb, Speaker Unit: 40mm Hd Driver Frequency Response: 20 Hz - 20 Khz Sensitivity: 105 Db, Impedance: 32 Ohms 16 1,000.00 16,000.00 66 Set Wired Handheld Microphone, 70 Hz → 14 Khz With 10-meter Cord, Anti-interference, Anti-whistling. 2 1,500.00 3,000.00 67 Piece Abrasive Disc Cutter Machine (ssc22 14-inch Cut Off Saw Machine 2200w) 5 7,577.00 37,885.00 68 Unit Electric Angle Grinder. Heavy Duty 4" 1000w Professional Power Tools Grinders Variable-speed 2 2,500.00 5,000.00 69 Piece Electric Heat Gun (shrink Gun With Accessories 2000 W) 5 1,725.00 8,625.00 70 Piece Sewing Machine Electric Built-in 4-step Buttonhole Stitch And 22 Patterns Shuttle Hook System And Front Loading Bobbin Sturdy But Light Aluminum Casting Housing Big Needle Plate With Seam Guide Line, Metal Hook Cover Pressure Regulator Button, Snap-on Presser Feet Stitch Length And Width Dial, Manual Reverse Stitch Button Built-in Led Light, Needle Position At Mid Or Left Drop Feed, Treadle Or Motor Options At Least 1 Year Warranty With After Sales Service 2 20,000.00 40,000.00 71 Piece Sewing Machine (zigzagger) Power：90w, Rated Voltage：220v, Number Of Stiches：23, Automatic Winding. Presser Foot Pressure Adjustable (free Installation) At Least 1 Year Warranty With After Sales Service 1 25,000.00 25,000.00 72 Set Electric Wood Power Planer. Wood Planer For Woodworking. 1200 Watts. 1300 Rpm. 50 Hz. 80mm Wide. With Accessories. With Warranty 2 3,000.00 6,000.00 73 Piece Handheld Rechargeable Pool Vacuum. • Strong Built-in 4v 2ah Ni-mh Rechargeable Batteries Suitable For Use With All Purpose And Above Ground Pools Up To 18 Feet Or 5.49 Meters In Diameter 0.21 Gal (0.8 Liters) Quick Release Transparent Debris Container 12 Gal/min. (45 Liters/minute) Water Suction For Efficient Debris Collection 94 Inches (2.39m) Lightweight Telescoping Aluminum Pole Two Interchangeable Brush Heads Automatic Shut-off Feature When Vacuum Is Not Submerged In Water Ipx8 Waterproof Switch For Added Protection 5-6 Hour Charge Time / 50 Minutes Maximum Running Time Usb Charging Cable Included For Convenient Recharging (plug Not Included) At Least 1 Year Warranty With After Sales Service 2 9,998.00 19,996.00 74 Piece Heavy Duty Automatic Electric Hand Dryer, Color: White Features: Cold And Hot Air Sensing Range: 12 + 3cm Hot Air Temperature: 40c - 54c Action Duration: 40s - 1 Min Water Power Source Voltage: Ac 220v 50/60 Hz Heating Power: 1800w Motor Speed: 2800r / Min At Least 1 Year Warranty With After Sales Service 2 5,000.00 10,000.00 75 Piece Heavy Duty Wood Circular Saw 7" Rated Power Input: 1500w Rated Frequency: 60hz Rated Voltage: 220v No- Load Speed: 5300r / Min Max. Disc Diameter: 185mm At Least 1 Year Warranty With After Sales Service 5 4,104.00 20,520.00 76 Unit Impact Drill 13mm Hammer Electric Drill Heavy Duty 220v Household Power Tools Industrial Screwdriver. 7.5 Amp Copper Motor, 700w, 3300rpm. With Warranty At Least 1 Year Warranty With After Sales Service 2 3,000.00 6,000.00 77 Unit Portable Generator With Electric Start, 10,000 Watt Starting Power & 8,000 Watt Running Power, Large Fuel Tank For Extended Run Time Powerful 420cc Ohv 4-stroke Engine Large 10.5-gallon Fuel Tank For Extended Run Time 120vac / 240vac / 60hz & 12vdc Includes Large 9.5" Wheels (free Installation) At Least 1 Year Warranty With After Sales Service 1 48,000.00 48,000.00 78 Unit Electric Welding Machine. Portable Igbt Inverter Welding Machine (dc Inverter Welding) With Accessories. With 3 Mos. Warranty 500w At Least 1 Year Warranty With After Sales Service 2 7,000.00 14,000.00 79 Piece Adjustable Wrench. Industrial Adjustable Wrench (12") 300mm Made Of High-quality Steel. 2 700.00 1,400.00 80 Set Allen Wrench. Short Arm Hex Allen Key Set With Carbon Steel Material. (1.5 To 6 Mm 7-piece Set) 2 100.00 200.00 81 Piece Anvil (15 Kg) With Steel Mounting Platform 2 12,000.00 24,000.00 82 Set Back Wrench. Set Of Heavy-duty Double Ring Spanner Wrench (metric 28mm - 32mm) Cr-v 2 700.00 1,400.00 83 Piece Ball Peen Hammer (½ Lb (80 Oz) 2 400.00 800.00 84 Piece Carving Chisels For Wood (wood Chisel 4 Piece/set) 2 798.00 1,596.00 85 Piece Chisel Rack For Wood Carving (professional 12-piece Wood Carving Chisel Set With Black Case Sharp Hand Tools For Beginners) 5 1,299.00 6,495.00 86 Set Combination Wrench Tool Set 16piece (8-32mm Professional Dual Purpose 2 700.00 1,400.00 87 Piece Corner Clamp (90-degree Single Swing Jaw Corer Clamp 68 Mm) 5 500.00 2,500.00 88 Piece Cutting Discs For Masonry. 4”-inch Professional Diamond Cutting Disc Continuous Eco For Tile / Ceramic 20 300.00 6,000.00 89 Box Cutting Disc For Steel. Ultra-thin Cutting Disc 4 (25piece) For Stainless 5 2,000.00 10,000.00 90 Set Drill Bits For Wood. 7pc X Long Wood Drill Bit Set 4mm 5mm 6mm 7mm 8mm 10mm 12mm X 300mm Brad Point Auger Drill Bits Wood 5 500.00 2,500.00 91 Set Drill Bits. 13pc Cobalt High Speed Steel Twist Drill Bit Set 1.5mm-6.5mm For Drilling Metal Wood Stainless Steel 5 500.00 2,500.00 92 Set Drill Bits.3-12mm Multifunctional Triangle Glass Metal Drill Bit Set Diamond Ceramic Tile Concrete Brick Wood Punching Hole Drill Bits 5 500.00 2,500.00 93 Piece Files Set For Wood Carving, Craft Metal, And Glass Stone (10-piece Needle File Set For Jewelries) 2 191.00 382.00 94 Piece Geometric Designer Templates (multi -functional Geometric Ruler) 5 118.00 590.00 95 Piece Geometric Shapes Set (wooden Montessori Learning Geometric Building Blocks) 5 1,176.00 5,880.00 96 Set Hacksaw Frame With Blade For Metal 12" 300mm Heavy Duty 3 350.00 1,050.00 97 Piece Hammer For Carpentry. Claw Hammer /16oz 3 300.00 900.00 98 Piece Hard Hat (heavy Duty Safety Helmet With Chin Strap) 3 300.00 900.00 99 Piece Heavy Duty Extension Wire (10-meter Wire: # 162 C, Plug: 15a, 25 V, Maximum Wattage:3750 W., At Least 4 Outlets) 12 1,500.00 18,000.00 100 Piece Heavy Duty Multi- Purpose Bench Vise (8") Mounted On A Steel Platform. 2 10,000.00 20,000.00 101 Set Heavy Duty Pliers. 8" Standard Pliers Cutter Longnose Combinations 8" Pliers 2 500.00 1,000.00 102 Unit Industrial Li-ion Cordless Laser Level 20v (12 Lines) 1pc Black Nylon Stand, 90mm Lift Adjustable; Front And Rear 55mm Adjustable Gap; 1/4″ And 5/8″ Copper Threaded Holes On Bottom; Strong Magnet On Side 1pc Sheet Metal Clip, Wavelength: 520nm Green Light Beam Accuracy: H/v Line ±3mm/10m Laser Intensity: Class Ii, <1mw Self Leveling: 0-4°, Expanded Angle: H&v 360° Max. Working Distance: 30m (without Detector) Maximum Drop Height: 1.5m, Function Mode: 1c, 2c, 3c At Least 1 Year Warranty With After Sales Service 1 15,000.00 15,000.00 103 Piece Jet-bow Beam Compass Drawing Set. The Set Includes 6" Speed Compass With Inter-changeable Pen, Pencil, Divider Parts, And Replaceable Needle Points. 4½" Bow Compass With Inter-changeable Pen, Pencil, And Divider Parts. 5 1,169.00 5,845.00 104 Piece Level Bar. Aluminum Level Bar With Magnet Heavy Duty 80cm 2 2,000.00 4,000.00 105 Set Magnetic Screwdriver Set Professional Cushion Grip 5 Flat Head And 4 Phillips Tips Screwdriver Non-slip 2 1,000.00 2,000.00 106 Piece Manual Canvas Pliers (industry Line Combination Plier Insulated Pliers) 5 416.00 2,080.00 107 Piece Metric Scale (technical Triangular Scale. Set Of 45, 90 Degrees) 5 1,000.00 5,000.00 108 Piece Mixing Paint Palette (paint Mixing Palette 10 Well Plastic) 2 45.00 90.00 109 Piece Picture Frame And Miter Clamp (90 Degree Right Angle Clip Picture Frame) 5 710.00 3,550.00 110 Piece Plumb Bob / Hulog. With String 350g 2 250.00 500.00 111 Piece Professional Compound Mitre Box & Saw (mitre Box And Box Saw Set 12 Inch) Miter Box Will Handle Stock 7 1/4" High, 8" Wide At 90°, And 5" Wide At 45°. The Saw Can Be Set At Any Angle And Has Automatic Stops For 90°, 45°, And For 5, 6, 8 And 12-sided Frames. 1 1,510.00 1,510.00 112 Set Rachet. Combination Wrench Steel Chrome Vanadium 8-24mm(per Piece) 2 2,500.00 5,000.00 113 Set Ratchet Wrench. 12piece 1/2 1/4 Inch Drive Ratchet Wrench Cr-v Socket Kits Mechanic Spanner Car Motorcycle Repair Tool 2 2,500.00 5,000.00 114 Piece Roofing Square. Dual Marking Right Angle Picture Framing Carpenter Ruler (stainless Steel Angle Ruler Aluminum Alloy Body Heavy Duty Tool) 10 500.00 5,000.00 115 Piece Rubber Mallet (16 Oz) 2 400.00 800.00 116 Piece Screen Print Squeegee (curved Aluminum Handle Squeegee 75) 2 310.00 620.00 117 Piece Staple Gun. Heavy Duty (gun Tacker/ Staple Gun Length-18cm Width -12cm H-3cm, Color- Silver Head T50) 2 2,000.00 4,000.00 118 Piece Steel Tape Measure (tape Measure 8m/20) 5 470.00 2,350.00 119 Piece Styrofoam Cutter (electric Foam Cutter Hot Wire Pen Portable) 1 1,500.00 1,500.00 120 Piece Swimming Pool Leaf Skimmer. Purpose: Used For Cleaning The Swimming Pool And Salvaging Pool Water Garbage. Material: Pp Plastic. Size: 420*280*30mm/16.54*11.02*1.18". 2 376.00 752.00 121 Piece Tape Measure-material: Pvc Centimeter Scale On Reverse Side Which Is Up To 300cm Large, Easy To Read Marking Measures Up To 120 Inches 3 300.00 900.00 122 Piece Toilet Paper Holder (wall Mounted Bathroom Toilet Paper Holder Tissue) 7 300.00 2,100.00 123 Piece Transparent Edge T- Square (hand Tool Inch Metric Ruler 6") 5 535.00 2,675.00 124 Piece Tri Square. High Quality Metal Frame 12" With Clear Markings 2 750.00 1,500.00 125 Piece Water Pipe Wrench 18" Liyabe Tubo Yabe Hand Tools 2 700.00 1,400.00 126 Piece Welding Mask (welding Helmet Auto Darkening Adjustable) 3 1,500.00 4,500.00 127 Piece Welding Protective Visor Glasses, Standard 3 420.00 1,260.00 128 Box Welding Rod Special N-6013 (2.5) (3/32 X 13”) 10kg Per Box 5 2,500.00 12,500.00 129 Piece Wood Carving Set. Carpentry Tools (professional 12/set Manual Wood Carving) 5 1,670.00 8,350.00 130 Set Wood Planer Set -katam. Locally Manufactured 8 Inches 2 500.00 1,000.00 131 Piece Wooden Hand Saw. 18" High Quality Metal Blade With Plastic And Rubber Handle 3 350.00 1,050.00 132 Piece Blender 1.5 Liter Material: Glass Input Voltage:220v Power Consumption:250w Stainless Steel Blade At Least 1 Year Warranty 5 700.00 3,500.00 133 Unit Blender. (9 In1 Food Processor, Good For Chopping, Slicing, Grating, Shredding, Whisking)18x18x38cm At Least 1 Year Warranty 1 3,742.00 3,742.00 134 Piece Bread Toaster (stainless Steel Top Plate) 25x 14.6x16.8cm At Least 1 Year Warranty 2 1,059.00 2,118.00 135 Unit Popcorn Maker/machine - Commercial Heavy Duty Power Supply：~220v 50hz, Power：1.3kw, Weight：21kg Size:560x420x680mm, Box Size：64*49*78cm At Least 1 Year Warranty 1 5,000.00 5,000.00 136 Set Deep Fryer Dimensions (w X H X D) 477 X 318 X 235, Weight 3.81kg Body Material Stainless Steel, Color Silver Power Consumption 2000w, Volume 4 With Temperature Control At Least 1 Year Warranty 2 7,200.00 14,400.00 137 Piece Electric Burger Griddle. Large Size Heavy Duty. Size:73cmx52cmx10cm. Bigger Waster Oil Container. Stainless Steel, Solid Gritty. Food Grade Material. At Least 1 Year Warranty 1 11,475.00 11,475.00 138 Piece Electric Kettle 1.5l At Least 1 Year Warranty 3 1,000.00 3,000.00 139 Unit Electric Rice Cooker 10l At Least 1 Year Warranty 2 5,000.00 10,000.00 140 Piece Electric Stand Mixer 5.5 Liter(1.9kg) With Bowl And 3 Whisk 6 Speed Setting Dough, Rotating Bowl, Speed Control At Least 1 Year Warranty 2 11,500.00 23,000.00 141 Unit Electric Steamer, 10.1-liter Capacity, 1.3 Liters Water Tank Capacity, 3 Layer Transparent And Collapsible Steamer Grids And Trays 90-minute Timer At Least 6months Warranty 1 2,500.00 2,500.00 142 Set Electric Takoyaki Machine And Double Pan 56 Holes Stainless Steel, Size: 437x 435x180mm At Least 6 Months Warranty 5 2,600.00 13,000.00 143 Unit Espresso Machine, 20 Bar Cappuccino Machines For Home, Latte Machine With Automatic Milk Frothier, Coffee Maker With Dual Wall Water Tank: 1300ml Milk Box: 700ml Power:1350w, Supply Voltage:220-240v Rated Frequency:50-60hz Maximum Pressure:20bar Weight:4.9kg, Packaging Weight:6.3kg At Least 1 Year Warranty 1 10,000.00 10,000.00 144 Unit Food Processor, 550watts, 12 Cup Capacity (96 Oz), 3 Processing Speed, Stainless Steel Weight: 6kg, Wxhxd (13in X 21in X 11in) At Least 1 Year Warranty 1 10,000.00 10,000.00 145 Piece Food Warmer Display Cabinet. Commercial Food Heater Glass Display Cabinet Heavy-duty Curved Deli Cabinet With Lighting. Constant Temperature Heating Display Counter Ideal For Fried Chicken Burger And Cooked Food. Size: Red+3 Compartments: 96x45x60cm. Rated Power: 300w. Rated Voltage: 220v.number Of Internal Layers: Three. Layers. Temperature Range: 30-80°c. Product Weight: 18kg. Built-in Energy-saving Warm Color Lamp, Improve The Display Effect At Least 1 Year Warranty 1 9,125.00 9,125.00 146 Piece Gas Range And Oven (1 Turbo, 1 Large Electric, And 2 Medium Burners) 33x42x39.5, (49 Liters) At Least 1 Year Warranty With After Sales Service 1 46,162.00 46,162.00 147 Piece Heavy Duty Electric Grill Machine Rated Power: 1000w Temperature Range: 60-200 Degrees Time Range: 0-30 Minutes Product Size: 380 * 250 * 188mm Material: Stainless Steel At Least 1 Year Warranty With After Sales Service 2 10,000.00 20,000.00 148 Piece Ice Crusher Machine Electric Stainless Steel Heavy Duty Portable Automatic Rotated Speed: 1500rpm Power:250 Size: 275x190x210mm Capacity: 2 Liter At Least 6 Months Warranty With After Sales Service 2 3,900.00 7,800.00 149 Unit Impulse Plastic Sealer Machine Plastic Sealing Machine (100mm | 150mm | 200mm | 250mm | 300 Mm) Weight: 1.06 Kg | 1.4 Kg | 1.3 Kg | 1.3 Kg | 1.58 Kg Size: (item Size) 100mm | 150mm | 200mm | 250mm | 300 Mm Power: 220v Sealing Width: 2 Mm Colour: Transparent Materials: Abs 2 1,500.00 3,000.00 150 Piece Large 18l Capacity Stainless Steel Electric Heating Tea Coffee Water Bucket Commercial Insulated Bucket Heating Barrel Boiled Water Bucket Material: Stainless Steel Adjustable Temperature：30-110° Rated Voltage：220v/50hz 2 3,000.00 6,000.00 151 Piece Meat Slicer (electric Machine Stainless Steel) 418x 293x 325mm 2 2,494.00 4,988.00 152 Piece Mechanical Microwave Oven (countertop,20 Liters) 700w- 1200w 1 5,075.00 5,075.00 153 Piece Oven. Four Plates Oven For Bread (stainless Steel) 530x595x570mm. Lpg Type At Least 1 Year Warranty With After Sales Service 1 48,924.00 48,924.00 154 Piece Portable And Foldable Charcoal Barbeque Bbq Grill 25"x30"x27" 1 4,000.00 4,000.00 155 Unit Rice Cooker Standard 2l Home Multifunctional Home Cooking 220v. Fast Cooking, Keep Warm Function, Non-stick Coating, Stainless Steel Cover. Input Voltage. 220v. Power Consumption 400w. Volume Capacity 2l Dimension (l X W X H) 215*215*215 At Least 1 Year Warranty 2 2,500.00 5,000.00 156 Piece Waffle Iron Pan 4 Interchangeable Plates 750 Watts At Least 1 Year Warranty 5 1,800.00 9,000.00 157 Piece Baguette Bake Mold Pan 34.5 Cmx 24cm (6cm Molder) Nonstick At Least 1 Year Warranty 10 399.00 3,990.00 158 Piece Bakery Display Rack (estante). Made Of Glass And Aluminum Frame. 4 Layer Of Glass (transparent) Or Acrylic With Partition. Rubber Wheels With Lock. At Least 2ftx 5ftx 4 Ft 1 40,000.00 40,000.00 159 Piece Baking Sheet 11x15 Inches 011 Thickness Heavy Duty Aluminum 10 360.00 3,600.00 160 Piece Baking Tray, Small (stainless Steel; Size Details: 23cm X 17cm) 8 258.00 2,064.00 161 Piece Baking/ Pastry Brush, Heat Resistant, Standard Size 10 35.00 350.00 162 Piece Blue Cutting Board (raw Fish)25.5cmx34cm, Plastic 5 460.00 2,300.00 163 Piece Boning Knife (stainless Steel) 24.4cm X 1.9cm X 1.7cm 3 492.00 1,476.00 164 Piece Bowl (serving Bowls, Clear Glass 20 Cm Diameter) 6 150.00 900.00 165 Piece Bread Plates (stainless Steel) 40x 60cm 20 1,027.00 20,540.00 166 Piece Bread Rack (stainless Steel)15 Layers 40x60cm Heavy Duty 1 20,000.00 20,000.00 167 Piece Bread Rack. Made Of 12 Mm Steel. 24"x5ftx5ft. Can Hold Up To 10 Trays (lagayan Ng Plantsa Ng Tinapay) 1 10,000.00 10,000.00 168 Piece Brown Cutting Board (raw Crops) 25.5cmx34cm, Plastic 5 460.00 2,300.00 169 Set Cake Decorating Kit. Piping Tips Set ( Stainless Steel,multicolor) 5 279.00 1,395.00 170 Piece Can Opener (stainless Steel Blade; Length: 17cm High) 4 500.00 2,000.00 171 Piece Carving Fork (stainless Steel; Size: 13 Inches Long) 3 162.00 486.00 172 Piece Casserole, Medium (stainless Steel: 3.9 Liter; Size: 12.5cm X 20cm) 4 689.00 2,756.00 173 Piece Casserole, Small (stainless Steel: 2.1 Liter; Size: 12cm X 15cm) 4 599.00 2,396.00 174 Piece Cast Iron Pots And Pans (ceramic, Non-stick) 21.85x 13.19x12.80inch 3 7,180.00 21,540.00 175 Piece Cheese Cloth (made From Cotton) 101 X 270cm 10 223.00 2,230.00 176 Piece Chef’s Apron. Black Apron With 2 Large Pockets Adjustable Apron Halter Neck Unisex Dirt And Stain Resistant, Size: Large 20 450.00 9,000.00 177 Piece Chef’s Apron. Black Apron With 2 Large Pockets Adjustable Apron Halter Neck Unisex Dirt And Stain Resistant, Size: Medium 20 450.00 9,000.00 178 Piece Chef’s Apron. Black Apron With 2 Large Pockets Adjustable Apron Halter Neck Unisex Dirt And Stain Resistant, Size: Small 20 450.00 9,000.00 179 Piece Chef’s Hat/cap For Men & Women, Breathable Hat Color White Fast Food Restaurant Coffee Shop Work Wear, Size: Large 20 250.00 5,000.00 180 Piece Chef’s Hat/cap For Men & Women, Breathable Hat Color White Fast Food Restaurant Coffee Shop Work Wear, Size: Medium 20 250.00 5,000.00 181 Piece Chef’s Hat/cap For Men & Women, Breathable Hat Color White Fast Food Restaurant Coffee Shop Work Wear, Size: Small 20 250.00 5,000.00 182 Piece Chef's Knife (stainless Steel) 33cm X 4.5cm X 2cm 3 750.00 2,250.00 183 Piece Cleaver Knife (stainless Steel) 7 Inches Or 2.5mm 3 1,074.00 3,222.00 184 Piece Colander, Medium (stainless Steel; Size: 28cm X 22cm) 3 298.00 894.00 185 Piece Colander, Small (stainless Steel; Size: 24cm X 22cm) 3 204.00 612.00 186 Piece Cookery Cabinets (made With Carbon Steel 5 Layers, Size: H: 144cm, W: 55cm) 1 3,621.00 3,621.00 187 Piece Cookie Press - Stainless Steel With 13 Disc And 8 Icing Tips, Dimension: 25x 14.5cm 3 462.00 1,386.00 188 Piece Cooler, 2.5ft X 2.5 Ft X 3ft Plastic, With Good Insulation 1 3,000.00 3,000.00 189 Piece Core Seed Remover (stainless Steel; Approx: 1.4x21.5cm) 4 229.00 916.00 190 Piece Cupcake Molder Tray Of 6 12 Holes Baking Pan Muffin Cup Cake 10 89.00 890.00 191 Piece Cutting Board (material: Bamboo; Size: 34x24x1.8cm/750g) 4 209.00 836.00 192 Piece Deep Fry Thermometer, Oil Temperature Gauge 3 320.00 960.00 193 Piece Digital Kitchen Thermometer (cooking/food Temperature; Size 34mm X 270mm) 3 486.00 1,458.00 194 Piece Double Boiler, Medium (stainless Steel; Size: 27x14x6cm) 1 389.00 389.00 195 Piece Dough Roller Pin, Wooden. 29.5cm Non-stick Silicone Rolling Pin Pastry Baking Decorating Tool 6 300.00 1,800.00 196 Piece Dough Scraper (stainless Steel) 16x12x2cm 3 178.00 534.00 197 Set Drinking Glass 10 Oz Tall Clear Tumbler Set Of 6 (dimensions: Lengthxheight: 5.5cmx12 Cm) 6 510.00 3,060.00 198 Piece Filling Funnel (stainless Steel) Upper Diameter: 10.5cm, Lower Diameter: 3.7cm, Height: 4.5cm 4 212.00 848.00 199 Piece Food Grade Silicone High Temperature Resistant Baking Mat Oven Baking (to Match Baking Pan), Browns Silicone Baking Oven Mat Liner, Non-stick For Pastry Cookies Dough 12 90.00 1,080.00 200 Piece Fruit Juicer, Standard Type 3 1,500.00 4,500.00 201 Piece Frying Pan, Large (scratch Resistant And Non-stick; Size: 28cm) 4 578.00 2,312.00 202 Piece Frying Pan, Medium (scratch Resistant And Non-stick; Size: 24cm) 4 380.00 1,520.00 203 Piece Frying Pan, Small (scratch Resistant And Non-stick; Size: 20cm ) 4 233.00 932.00 204 Piece Funnel (stainless Steel) 22x14.5cm 3 715.00 2,145.00 205 Piece Glass Rack (plastic-coated Metal; Capacity: 24piece Glass; Dimension: L:52cm; W: 36cm; H:8cm) 2 461.00 922.00 206 Set Glasses. Dining Glasses (6piece. Thick Clear Glass: W: 3inches And H: 4inches) 5 265.00 1,325.00 207 Piece Green Cutting Board (for Fruits And Vege)25.5cmx34cm, Plastic 5 460.00 2,300.00 208 Piece Hair Net. Unisex Hair Net Cap Hair Mesh Weaving Wig Cap Hair Styling Tools Nylon Hair Nets Hollow Out High. Black 300 30.00 9,000.00 209 Piece Hand Mixer (stainless Steel Bowl) 270x165x290mm, 2.8 Liters Capacity 3 1,755.00 5,265.00 210 Piece Ice Cream Scoop (stainless Steel) Diameter: 4.5cm, Length: 18cm 6 208.00 1,248.00 211 Piece Kitchen Carts (2 Layer Stainless Steel Carts With Two Brake Wheels; Size: 400mm X 500mm X 860mm) 2 3,019.00 6,038.00 212 Piece Kitchen Fork (stainless Steel; Size: 7cmx4cmx21cm) 5 72.00 360.00 213 Piece Kitchen Scale Food (manual) 5 Kilogram 2 300.00 600.00 214 Piece Kitchen Spoon (stainless Steel; Size: 8cmx6.5cmx21cm) 5 86.00 430.00 215 Piece Kitchen Spoon, Slotted (material: Plastic; Size: 7x3x43cm) 5 289.00 1,445.00 216 Piece Large Wooden Turner For Large Oven. Kitchen Turner Flat Spatula Scraper, Acacia Wood 10.5 Inches Long And 2.75 Inches Turner 3 200.00 600.00 217 Piece Lpg Tank 11kg 4 4,500.00 18,000.00 218 Set Measuring Cup. Measuring Cup Sizes: 1 Cup (250ml). 1/2 Cup (125ml). 1/4 Cup (60ml) ; 1/8 Cup (30ml). Materials. Plastic (abs) 3 500.00 1,500.00 219 Set Measuring Spoon 1tbsp 15ml, 1/2tbsp 7.5ml, 1tsp 5ml, 1/2tsp 2.5m Material: Stainless Steel 3 400.00 1,200.00 220 Piece Meat Thermometer, Brifit Waterproof Kitchen Meat Thermometer, Foldable Digital Instant Read Food Thermometer 3 400.00 1,200.00 221 Piece Medium Graters (stainless Steel) 18/8 2 430.00 860.00 222 Piece Mixing Bowl: 30 Cm L30xw27.5xh11.4 Cm Thickness: 0.04 Cm. Material: Stainless Steel 10 900.00 9,000.00 223 Piece Muffin Pan Non-stick Dimension: 26.5x35x3cm, Capacity: 12 Cup, Color: Black Non-stick Surface For Easy Release And Quick Cleanup Dishwasher Safe, Ideal For Baking Muffins, Cupcakes Nonstick Coating Helps Ensure Effortless Food Release 5 700.00 3,500.00 224 Piece Muti-function Vegetable Fruit Peeler Slicer Cutter Chopper (material: Abs + Stainless Steel) 4 429.00 1,716.00 225 Piece Muti-purpose Kitchen Scissors/ Shears (scissors Length: 21.5cm; Blade Length: 10cm; Handle Length: 11.5cm; Handle Width: 9.5cm; Blade Thickness: 0.4cm Weight: 200grams) 8 500.00 4,000.00 226 Piece Oven Thermometer 3 389.00 1,167.00 227 Piece Oysters Knife (stainless Steel) 15.5com X 6.5cm X 3cm 3 187.00 561.00 228 Piece Parisienne Scoop (stainless Steel Blade With Plastic Handle) Scoop Diameter: 30mm And 27mm; Total Length: 170mm 3 216.00 648.00 229 Piece Pastry Tubes (stainless Steel) 3cm X 3cm X 6.1cm 8 142.00 1,136.00 230 Piece Pepper And Salt Grinder (made With Stainless Steel, Glass, And Ceramic) Approx. 19x6.5cm 6 296.00 1,776.00 231 Piece Piping Bag (disposable Bag Size: 24.5cm X 17cm) 50 208.00 10,400.00 232 Piece Pitcher (durable Crystal-clear Glass 1.5l) 6 300.00 1,800.00 233 Piece Place Mat (table Placemat Pvc Anti-slip Placemat Wasahble Durable Kitchen S:30x45cm) 10 250.00 2,500.00 234 Piece Plastic Containers, Microwavable Round Canister, Food Storage Container (400 Ml) 40 20.00 800.00 235 Piece Plastic Measuring Pitcher Jug With Measurement(set) Maximum Of 1 Liter 3 126.00 378.00 236 Set Plastic Silverware Or Real Silverware (stainless Steel; 18piece Utensils Set Includes: 6 Dinner Fork, 6 Dinner Spoons And 6 Dinner Teaspoons) 2 415.00 830.00 237 Piece Plate Rack (stainless Steel; Size: 30cmx22.8cmx12.9cm) 3 492.00 1,476.00 238 Dozen Plates (12 Piece Plates 8-inch Melamine White) 6 700.00 4,200.00 239 Piece Pot Holder, Basahan Bilog 6 Inches Diameter 12 15.00 180.00 240 Piece Potato Masher With Soft Grip Handle (stainless Steel) 9.5x27x8cm 2 357.00 714.00 241 Piece Pressure Cooker 3.5 Liter 2 1,200.00 2,400.00 242 Piece Red Cutting Board (raw Meat)25.5cmx34cm, Plastic 5 460.00 2,300.00 243 Piece Revolving Cake Stands (aluminum)12 Inches 5 850.00 4,250.00 244 Piece Rolling Pin Stainless Steel Pressing Stick Pizza Dough Non-stick Dough Roller, (29.5 Cm) 6 300.00 1,800.00 245 Piece Round Cake Molder 4, 6, 8 Inches Set 5 161.00 805.00 246 Piece Scraper(rubber) 30cm X11cmx6.8cm 5 130.00 650.00 247 Piece Serving Bread Tray (stainless Steel) 45cmx2.8cm 6 1,229.00 7,374.00 248 Piece Serving Spoon (heavy-duty Stainless Steel) Length: 22.5cm; Width: 6cm 24 102.00 2,448.00 249 Piece Siever, Small (stainless Steel) 14 Cm 3 188.00 564.00 250 Piece Skimmer, Fine (stainless Steel) 7.3cm X 5cm X 21.5cm 3 160.00 480.00 251 Piece Skimmers, Spider (stainless Steel) Handle: 14; Radius: 20 3 115.00 345.00 252 Set Small Plate / Saucers (ceramic With Size: 6 Inches And 6piece Per Set) 2 150.00 300.00 253 Piece Soup Cup Rack (2 Layered Rack; Size: 35 X 25 X 28cm) 3 899.00 2,697.00 254 Piece Soup Ladle, 12 Oz (stainless Steel And Wooden Handle: 15 X 51 Cm) 5 360.00 1,800.00 255 Piece Soup Ladle, 4 Oz (stainless Steel; Size: 7.5cm X 30 Cm) 5 124.00 620.00 256 Piece Soup Ladle, 6 Oz (stainless Steel; Size: 7.5cm X 30 Cm) 5 194.00 970.00 257 Piece Soup Ladle, 8 Oz (stainless Steel And Wooden Handle: 10 X 51 Cm) 5 290.00 1,450.00 258 Piece Spatula (silicon) 27.2 X 5.5 X 1.5cm 3 169.00 507.00 259 Piece Square Cake Molder 9, 11, 13 Inches Set 5 160.00 800.00 260 Set Stainless Icing Tip (set-12piece) Cake Decorating Kit Stainless. Icing Piping Nozzles Pastry Tips Cake. 10 499.00 4,990.00 261 Unit Steamer. 3 Layer Steamer 34cm Stainless Steel Cooking Pots Cookware Steam High Quality 2 6,499.00 12,998.00 262 Piece Stock Pot, Big (with Glass Cover; Size: 34.5 X 27.9 Cm X 16.6 Cm) 2 798.00 1,596.00 263 Piece Strainer, Chinois, Small (stainless Steel) 16cm Handle: 5.5inches 3 198.00 594.00 264 Piece Strainer, Medium, Fine (stainless Steel) Diameter:16cm; Length: 30.5cm; Depth: 5.9cm 3 180.00 540.00 265 Piece Strainer, Small, Fine (stainless Steel) Diameter:14cm; Length: 29cm; Depth: 5.5cm 3 160.00 480.00 266 Set Teacups (ceramic White; Capacity: 250ml) (6piece. /set) 2 400.00 800.00 267 Piece Tenderizer (pin Tenderizer) Stainless Steel Diameter: 5cm, Height: 19cm 3 119.00 357.00 268 Piece Tenderizer Mallet. (tenderizer) Stainless Steel 12.6 Inches X 11.5x4cm 3 240.00 720.00 269 Piece Tongs (stainless Steel) 12 Inches 4 179.00 716.00 270 Piece Tongs (stainless Steel) 9 Inches 4 110.00 440.00 271 Piece Turner (stainless) Dimension: 34.5 X 9.8 X 4.4 Cm 3 280.00 840.00 272 Piece Utility Tray (stainless Steel: Stain Resistant; Size: 45cm X 35cm X 4.8cm) 12 189.00 2,268.00 273 Piece Weighing Scale Digital. Display Mode: Led/lcd+light . Weighing Range :40kg. Accuracy: 2g. Product Size: 35x33x14cm 3 Lcd Display On The Operator’s Side Of The Scale As Well As 3 Lcd Display On The Customer’s Side. Minimum Capacity Is 2g. Maximum Capacity Is 40kg Power Source: Built In Rechargeable Battery With Usb Cable Battery Powered Or Connect Usb Cable. Battery Powered Or Connect Usb Cable To Use Weight Platform/tray Material Is Stainless Steel. 1 5,000.00 5,000.00 274 Piece White Cutting Board (for Bread And Pastry) 25.5cmx34cm, Plastic 5 460.00 2,300.00 275 Piece Wire Skimmer, Small (stainless Steel) Handle: 14; Radius: 14 3 105.00 315.00 276 Piece Wire Whisk - Length: 30 Cm (12 ") Material Stainless Steel 4 320.00 1,280.00 277 Piece Wire Whisk, Heavy Duty (stainless Steel+plastic Handle; 14 Inches) 4 258.00 1,032.00 278 Piece Wire Whisk, Medium (stainless Steel+plastic Handle; 10.2 Inches) 4 189.00 756.00 279 Piece Wok, Medium (nonstick Carbon Steel; Size: 36cm) 1 401.00 401.00 280 Piece Wok, Small (nonstick Carbon Steel; Size: 32cm) 4 389.00 1,556.00 281 Piece Wooden Spatula 9cm Sandok, 34 Cm Long 4 65.00 260.00 282 Piece Wooden Spoon (made With Beech Wood 10cm X 34cm X 2cm) 6 244.00 1,464.00 283 Piece Wooden Turner, Wooden Sandok Kitchen Spatula Spoon Turner Cooking, 3" Width Of Sandok, 10" Long 4 65.00 260.00 284 Piece Yellow Cutting Board (cooked Meat) 25.5cmx34cm, Plastic 5 460.00 2,300.00 285 Piece Zester (stainless Steel) Length: 30cm/11.81 Inches 3 268.00 804.00 286 Set 4 Inflatable Tools/ Speech Therapy Tools Package, Blowing Flute/pin Wheel Whistle, Made Of Plastic 20 150.00 3,000.00 287 Set Adl Board - 6 Colors, 6 Different Dressing Skills Training. A Quiet Skill Book Made Of Cardboard And Non- Woven Fabric. Suitable For Children 2-7 Years Old. Package Dimensions: 11.73 X 9.76 X 2.28 Inches Item Weight: 1.28 Pounds" 10 700.00 7,000.00 288 Unit Balance Board- Balance Board Type: Rocker Board Dimensions: 32.28 X 11.81 X 0.59 Inches Weight Capacity: 100 Kg Material: Beech Wood Anti-skid Feature: Not Specified 3 3,700.00 11,100.00 289 Set Balance Steppingstone/balancing Coordination Obstacle Course Therapy (specs: Good For 20-40kls, Assorted Color) 1 3,000.00 3,000.00 290 Piece Core Peak Bolsters- An All-purpose Positioning Aid • Provides Support Under The Legs, Arms, Feet, And Other Areas Of The Body. Fits Standard Treatment Tables • 18" In Length With At Least 6" In Diameter. 2 9,006.00 18,012.00 291 Set Dry Erase Sleeves. Reusable Dry Erase Pockets. Colors: Blue, Pink, Yellow, Red, Green, Purple. Size: 25.5*35.5cm(1piece). Quantity: 12piece Package Including: 6 X Dry Erase Pockets 6 Pens 10 796.00 7,960.00 292 Unit Electrical Stimulator. Multiple Mode Electrical Stimulator-1 Second Measuring Time. 3 Color Backlight Fever Reminders Auto Shut Off At 18 Seconds Store 50 Sets Of Data. Body Temperature Measurement: 34.0-42.9°c / 93.2-109.2°f. At Least 1 Year Warranty With After Sales Service 2 9,884.00 19,768.00 293 Unit Exercise Steps-aerobic Step Board 69 X 28 X 15cm. Dimension: 69 X 28 X 15cm Length: 27" Width: 10.5" Adjustable Height Up To 10cm To 15cm. Offers A Secure, Nonslip Surface For Your Workout Routine, Nonskid, Feet Provide Stability & Protect Floors. 5 1,934.00 9,670.00 294 Piece Foot Reflexology Machine Power Source:220 – 240v; Power Consumption: 50w; Dimensions (l X W X H) :410mm X 390mm X261mm At Least 1 Year Warranty With After Sales Service 2 25,000.00 50,000.00 295 Piece Gait Belt-1x Transfer Gait Belt Measurement Length: 60 Inches, Width: 2 Inches 3 1,458.00 4,374.00 296 Packs Ice Massage Caps- Size: 2 Count (pack Of 1) Measuring 2.9” In Diameter, The Ice Cup Massager Holder Also Fits Comfortably In The Hand. Material: Polyethylene 10 700.00 7,000.00 297 Piece Interlocking Rubber Mat-size 1x1 Meter X 25 Mm Color Red, Hardness: 55 To 60 Shore, High Density 38 1,750.00 66,500.00 298 Piece Kinesiology Tape-ultra-strong And Sticky-hypoallergenic Adhesive Water Resistant. 97% Cotton, 3% Nylon. 180% Stretch For Full Range Of Motion Latex And Zinc Free Sticks 2-7 Days 5-10 Applications Per Roll Each Is 2""x 16.4"" (5cmx5cm) 10 2,100.00 21,000.00 299 Set Medicine Ball, Set Contains 6lb, 8lb, 10lb, And 15lb Medicine Balls. Medicine Ball Exercise Ball Workout Dumbbell Set Slam Ball 1 4,000.00 4,000.00 300 Piece Mobilization Belts And Devices- Size 8 Feet Specific Uses For Product. Use For Legs, Hips, Arms, Back, Whole Body - High-quality Nylon Mobilization Belt Features A Plastic Side-release Buckle And Is Designed For Durability And Patient Safety. 3 2,850.00 8,550.00 301 Unit Paraffin Bath- Large Opening Design: Inner Pot Allows For Hands, Feet, And Elbows To Be Dipped Into The Melted Wax. Alloy Heating Pot Melts Paraffin Wax Blocks In 0.5 Hours. Adjustable Heating Ranges From 86-158°f. Timer: Settable From 1 To 99 Minutes. Free Installation At Least 1 Year Warranty With After Sales Service 1 32,340.00 32,340.00 302 Piece Pool Noodles 60 Inch 2 300.00 600.00 303 Piece Pull Buoy Swim Training Leg Float 2 600.00 1,200.00 304 Piece Quad Cane -stable Structure, Material: Stainless Steel, Abs Non-slip Handle, Ergonomic Design, Comfortable Grip. Spring Button For Easy Height Adjustment. Firm Lock Hoop To Stabilize The Body. 2 2,740.00 5,480.00 305 Set Reflex Hammer-features: Pointed Babinski-style Tip Zinc Alloy Comfortable Handle Grip Control, Hammer For High Elastic Pvc Rubber Material: Zinc Alloy + Pvc; Color: Black Package Size: 27*11*3.5cm/10.6*4.3*1.3-inch Package Weight: 140g/4.9oz. 1 8,100.00 8,100.00 306 Piece Rocker Boards. Dimensions: 28 X 28 Inches, 7 Inches Height; Materials: European Birch Plywood, Water-based Finish With Slip-resistant Rug; Hold Up To 85 Kilos. 5 9,900.00 49,500.00 307 Piece Round Bolsters-weight：0-0.5 Kg Shape: Column, Feature: Memory, Filling: Microfiber Material:100% Fiber, Size:8" X 36", Color: White Ideal For Hugging, Cylindrical Pillow, Great For Side Sleepers. 2 1,760.00 3,520.00 308 Set Rubber Mat (specs: 30x30cm,36 Piece.) 2 500.00 1,000.00 309 Piece Scooter Boards. 12" X 12" Heavy Duty Plastic Board, Non-marring Double Ball-bearing Swivel Casters And Molded Plastic Built-in Handles On Each Side, Holds Up To 150 Lbs. 2 24,990.00 49,980.00 310 Piece Sensory Cushion: Circular Shape, Rubberized. Size: 35cm X 5.5cm. Free Air Pump Pin, (red, Blue, Violet, Ot Pink) Tactile For Balance And Motor Coordination Fidget Massage Yoga Training Exercise 2 1,100.00 2,200.00 311 Set Sensory Floor Tiles 6pc Sensory Stimulation Walk Crawl Massage (specs: Rubber 1ft X 1ft Per Tile, Assorted Color) 2 2,000.00 4,000.00 312 Piece Slant Board. 12" X 16”, Adjustable Angles (20 To 32 Degrees), With Heavy-duty Metal Clip 5 4,500.00 22,500.00 313 Set Splinting Materials- Rescue Padded Board Splint. 6 Paddes Wood Splint (different Sizes) Sizes: 35"", 25"" And 15". Velcro Straps Color: Blue. 10 4,200.00 42,000.00 314 Set Stationary Bike. Spin Bike Exercise Bike Fitness Home Equipment Spinning Bike Fitness Bike. With Digital Information, Free Installation. Stationary Bike-flywheel Resistance Is 18 Kg./20kg. Maximum Bearing Capacity 300 Kg. 6 49,990.00 299,940.00 315 Unit Step Stools- Step Stools Double Steel Caravan Step. Rubber Non- Slip Steps. Leg Distance Front To Back 65 Cm. Width 42 Cm. Top Step Height 38 Cm. Bottom Step 20 Cm. 2 3,600.00 7,200.00 316 Set Theraband -4 Resistance Levels, Including Yellow, Red, Green, And Blue Supplied In Lay Flat Length Of 8", 12" And 18" Latex Rubber Weight Level: Yellow: 3 Lbs-4.3 Lbs Red: 3.7 Lbs-5.5 Lbs Green: 4.6 Lbs-6.7 Lbs Blue: 5.8 Lbs-8.6 Lbs 3 10,100.00 30,300.00 317 Unit Therapist Stools On Wheels-adjustable Height Of 19 - 24". It Comes With A 3" Hi-density Cushion With Multi-layered Padding, And A 14" Seat Diameter. Built With 5 Casters Made Of Plastic Easy To Clean. Color: Black 2 4,950.00 9,900.00 318 Piece Therapy Putty. Set Of Four Colors. Finger Training Putty Like Squeeze, Pinch, Stretch And Twist. Decompression Toy Mud Grip Hand Strengthening Exercise 8 Grams Putty, 4.5cmx7cm Plastic Container 40 300.00 12,000.00 319 Set Trampoline With Handrails 40-inch Jumping Surface Area, Handrail Adjusts From 28.5"" To 36.5""h 16lbs. Holds Up To 300 Lbs At Least 1 Year Warranty With After Sales Service 2 11,580.00 23,160.00 320 Set Treadmill. Heavy Duty Electric 139cm Long Portable Treadmill With Digital Indicators Like Timer And Speed Selector. Free Installation. At Least 1 Year Warranty With After Sales Service 4 49,950.00 199,800.00 321 Unit Tumble Barrels-inside Diameter: 18"-24”, Outside Diameter: 24", Weight: 250lbs. (free Installation) At Least 1 Year Warranty With After Sales Service 1 40,695.00 40,695.00 322 Set Vestibular Balls- (3 Pieces) Material: Synthetic Material Size: 55.0 / 65.0 / 75.0 Cm. Weight: 1100.0 / 1400.0 / 1700.0 G. Color: Violet / Blue / Black 1 6,460.00 6,460.00 323 Piece Vestibular Ball-size 45-90 Cm Pvc Material, Anti-burst And Non-slip Bearing 200 Kg., Color Blue, Weight 900 G. 2 800.00 1,600.00 324 Piece Wedge Bolsters- A Firm And Breathable Bed Wedge Pillow Stays Cool, And Its Measurements Are 25″l X 25″w X 12″h Inches. / Breathable & Washable Cover / Designed To Provide Higher Body Support. 2 6,998.00 13,996.00 325 Piece Weighted Vest. Breathable Cotton Denim; Removable ¼-pound Weights; Chest 28"-30", Shoulder-to-waist 16", Includes 8 Weights (¼ Lb Each) 5 3,500.00 17,500.00 326 Piece Wheelchair Sports. Materials: Lightweight Aluminum Frame: Pneumatic Wheels; Padded Seat; Built-in Back Wheel Casters For Stability; Wheelchair Width Including Wheels: 62cm Wheelchair Seat Width: 38cm; Wheel Diameter: 60cm; Seat Depth: 36cm; Backrest Height: 28cm; Weight Capacity: 100kg 9 40,000.00 360,000.00 327 Piece Wheelchair Standard Heavy Duty Foldable (spes: Folded Dimension:95x86x29cm; Seat Width:49cm; Aluminum Footrest, Fixed Arm Rest And Leg Rest, Front 8" Pvc Castor Wheels, Rear 24" Pu Spoke Wheels) 10 6,000.00 60,000.00 328 Piece Wheelchair- Front Wheel Size: 6 Inches Net Weight Of All Aluminum Alloy Frame: 11kg, Net Weight: 11kg Expanded Size: (82x58x87 In Cm), Seat Depth: 38cm Rear Wheel Size: 16 Inches, Back Height: 42cm, Seat Width: 45cm Folded Size:(70x25x72 In Cm), Handrail Spacing: 55cm 3 7,000.00 21,000.00 329 Piece Wiggle Cushion (inflatable) With Hand Pump. Diameter 10.75" / 27 Cm, One Side Features Flexible Nubs, Other Has Smaller Bumps. 5 1,500.00 7,500.00 330 Set Wooden Hammering Ball (specs: 4 Balls Red,blue,green,yellow; 1 Hammer; 1 Bench) 5 300.00 1,500.00 331 Piece Aqua Dumbbells Large (6"x12.5") Thickness:4" 2 500.00 1,000.00 332 Piece Aqua Dumbbells Medium (6"x10.5") Thickness:3" 2 500.00 1,000.00 333 Piece Aqua Dumbbells Small (6"x8") Thickness:2" 2 500.00 1,000.00 334 Set Dumbbells Sets- Weight: 37kg With Rack Type: Medical Rehabilitation Equipment, Total 18 Dumbbells 1 Lb / Piece, 2 Pieces 2 Lbs / Piece, 4 Pieces 3 Lbs / Piece, 4 Pieces 4 Lbs / Piece, 4 Pieces 5 Lbs / Piece, 4 Pieces 1 25,000.00 25,000.00 335 Unit Augmentative Communication Systems. Package Dimensions 9.13 X 3.03 X 1.1 Inches Batteries 2 Aaa Batteries Required. (included) Preprogrammed Commands Wide Variety- Travel Bag- Aac Device 10 3,702.00 37,020.00 336 Unit Call Lights. Receiver Working Voltage: 110-260v Transmitter Battery: 12v 23a Alkaline Battery Working Distance: 1000 Feet In Open Area. 3 Receivers, 2 Transmitters. 2 X Double-sided Tape. 1 X User Manual. 2 X 12v 23a Batteries. 10 1,536.00 15,360.00 337 Piece Chewy Tubes Are Innovative Oral Motor Devices Designed To Provide A Resilient, Nonfood, Chewable Surface For Practicing Biting And Chewing Skills. Material: Thermos Elastic Polymer, 8cm Long Hollow Stem And 6cm Wide Top 50 200.00 10,000.00 338 Box Wooden Tongue Depressor Sterile (sure-guard). Disposable (lxw) 120-160mmx14-18mm, Thickness:1.8-2.2mm, Singleuse,nonsterile 10 200.00 2,000.00 339 Unit Blood Pressure-blood Pressure Monitor Type: Upper-arm Monitor Type: Digital Cuff Size: 32cm Dimension (w X H X D): 145 X 466 X 145mm Weight: 250g Power Supply: Battery Type: Li-polymer Smart App Availability: Yes Automatic Shut Off: 1 6,560.00 6,560.00 340 Unit Stethoscope: Dual Tube Stethoscope Weight: 185g, Length: 80cm Product Material: Polymer Diaphragm, Listener Material: High-density Stainless Steel Product Composition: Ear Tip, Ear Hooks, Leaf Spring, Hose Heads, Diaphragms 1 1,380.00 1,380.00 341 Piece Thermometer- Body Temperature Measurement: 34.0-42.9°c / 93.2-109.2°f. Material: Abs Plastic. Accuracy: (+/-)0.2°c. Auto-shutdown Time: About 18s Power Supply: 2 * 1.5v Aaa Batteries 1 Year Warranty 5 1,600.00 8,000.00 342 Piece Braille Contraction Pamphlet. Unified Contraction Pamphlet 4"x6". 25 600.00 15,000.00 343 Piece Braille Slate. 27 Lines, 30 Cells Per Row, Black 25 1,000.00 25,000.00 344 Piece Braille Stylus. Round Or Y Shape 25 200.00 5,000.00 345 Set Chess Board For Blind. Plastic Pieces With Special Markings, Board With Pattern To Distinguish White And Black Squares With Slots To Hold The Pieces. At Least 12"x24" Plastic Board. 4 5,000.00 20,000.00 346 Set Communication Boards. Measures 9"x7.5". Binder Comes With 5 Different Colorful 10 Mil Poly Dividers, 3 Hard Strips (hook) Attached On Each Side To Hold 30 Cards. Each Card Measures 1.5 X 1.5. Inch Mounted With 1/2-inch Soft Dot (loop), And Round Corner Cut. 10 6,172.00 61,720.00 347 Piece Contraction Pamphlet. Nemeth Code. 4"x6". 25 600.00 15,000.00 348 Piece Cranmer Abacus 25 650.00 16,250.00 349 Box Fidgets. Contain A Variety Of Quiet Devices That You Can Roll, Pop, Zip, And Squeeze 5 1,800.00 9,000.00 350 Set Geometric Measurement. Set Of Protractor, Ruler And Triangles Made Of Plastic With Embossed Marking For The Blind, Standard Size. 15 1,000.00 15,000.00 351 Set Goniometers- Protractor Goniometer With 360 Degrees Coverage To Measure Joint And Compare The Changes In Joint Angles Material: Clear Plastic 3 Goniometer: 12-inch, 8 Inch And 6 Inches 2 600.00 1,200.00 352 Piece Hand Dynamometer - Hand Dynamometer Type: Electronic Counting Gripper Function: Comprehensive Fitness Exercise Material: Abs Size: 15cm/5.90""x10.5cm/4.13""x2cm/0.79"" 1 1,900.00 1,900.00 353 Set Jaw Exercisers, Reusable Speech Therapy Tools- Color: Red, Packing Single Loaded, Function: Teether, Material: Silicone, Shape: Tube, Material Feature: Bpa Free, Item Code: 759057460, Category: Soothers & Teethers 10 650.00 6,500.00 354 Set Jaw Grading Bite Blocks- Color: Purple, Brand: Talktools, Item Weight: 0.16 Kilograms, Shape: Teething Block 20 350.00 7,000.00 355 Unit Pediatric Walker - 360-degree Swivel Front Casters For Versatile And Flexible Mobility. Total Height: 75-90cm Side Wheel Width: 70cm. Front And Rear Track Width: 75cm. Left And Right Wheel Track: 40cm Suitable Height: 85-120cm. Weight: About 12kg 2 17,998.00 35,996.00 356 Piece Pediatric Walker- Height-adjustable Frame Sizes. 360-degree Swivel Front Casters For Versatile And Flexible Mobility. Foot-operating Locking Mechanism On Front Casters. Rubber Tire Design 3 13,200.00 39,600.00 357 Set Phonics Phones. Specifications - Each Pack Includes Two Durable Whisper Phones, One In Vibrant Blue And One In Eye-catching Red. 10 536.00 5,360.00 358 Set Scrabble Board For Blind. Made Of Plastic With Special Markings On Tiles And Board. At Least 18"x18" Board. 5 4,000.00 20,000.00 359 Piece Small Silicone Food Tongs/tweezer For Kids (specs: 5-6 Inches Long, Assorted Color, Silicone Or Plastic) 10 100.00 1,000.00 360 Piece Walking Cane-adjustable Aluminum Cane With Wooden Handle, Anodized Finish, And Rubber Tip. The Tube Has A Spring Lock Pin For Adjusting Handle Height From 58-94 Cm. 2 1,320.00 2,640.00 361 Piece White Cane For Adults- Foldable Aluminum With White Anodized Finish And Plastic Tip. The Tube Has A Spring Lock Pin For Adjusting Handle Height From 58-94 Cm. 20 1,500.00 30,000.00 362 Set Articulation Cards. Genre: Children's Learning & Education Sub-genre: Society & Culture Label: Scholastic Teaching Resources Language: English Publisher: Scholastic Teaching Resources 10 3,913.00 39,130.00 363 Set Basic Vocabulary Board. Each Unit Comes With: Flashcards Smash Mat Trace And Color Cut And Glue Flipbook Black And White Versions Of All Activities 10 10,150.00 101,500.00 364 Piece Building Block Set With 96 Pegs In Board For Color Recognition Sorting & Counting. Assembled Product Dimensions (l X W X H) 0.72 X 0.49 X 0.39 Feet. Width-0.49 Ft 5 2,000.00 10,000.00 365 Set Busy Board Sensory Toys For Learning Fine Motor Skills (specs:1ftx1ft : Book-type With Different Fine Motor Activities: Felt Paper, Plastic And Cloth Materials) 3 800.00 2,400.00 366 Set Dolch Basic Sight Words. (bitay Max). Printed On White Tarpaulin 2 Ftx 3 Ft Binded With Two Wooden Sticks. With String (sabitan). Words At Least 2" Height Black, Arial Font Style. 10 1,500.00 15,000.00 367 Set Felt Large Story Board (specs: 2ft X 3ft, Thick Felt Material With Felt Piece Such As Vehicles, Planets For Story Telling) 2 1,000.00 2,000.00 368 Flash Card. Picture And Words Laminated In Thick Plastic Wrapper. New Design Phonics Flashcards Cvc Short Vowel Sounds Word List With Pictures Jumbo Size 14 350.00 4,900.00 369 Piece Kids Play Tunnel (specs Made Of Polyester Cloth Collapsible) 3 1,000.00 3,000.00 370 Set Plastic Puzzle Blocks- Mixed Sized -250 Piece -23x15x10 Cm 260 Piece. -22.2x16.8x10.3 Cm; 520 Piece., 22.2x16.8x16.3 Cm 2 700.00 1,400.00 371 Set Toy Blocks. 160piece Waffle Blocks House Building Blocks Educational Toys For 4 Years Old Kids. 2.16"x2.16" Multi-colored Plastic Blocks. Non-toxic And Odorless. 9 500.00 4,500.00 372 Set Wind Up Toys. Category: Clockwork Engineering Road Roller Material: Plastic, Size: 9.9*6.5*5.3(cm) Color: Three-color Random Hair, Ages: 3+ 10 440.00 4,400.00 373 Set Wooden Building Blocks (specs: 2x3x1 Inches, Assorted Shapes, And Colors: 10-15 Piece) 2 1,000.00 2,000.00 374 Set The Wooden Castle Made Of Colorful Blocks On Carpet In The Playroom. Size Max 6720x4480px • 56.9cm X 37.9cm 5 3,000.00 15,000.00 375 Set Wordless Picture Books. A Wordless Book About Dealing With Big Emotions Like Fear, Grief, Loss, Sadness, And Anger Hardcover | 36 Pages Product Dimension: Approx. W1cm X L22.2cm X H22.2cm Product Weight: Approx. .28kg 20 1,998.00 39,960.00 376 Piece 7kg Hand Carry Luggage Travel Bag. 360 Universal Wheels. Divided Internal Space. 57 Liters Capacity. 40 X 57 X25 Cm Dimension. 3 3,500.00 10,500.00 377 Pack Clothes Pin (laundry Clothes Pins Spring Clips 24 Piece Plastic ) 5 150.00 750.00 378 Piece Comb (1 Dozen Suklay 3-hole X Sz-28 Big) 20 90.00 1,800.00 379 Piece Dipper (plastic Dipper L 11" X W 36"x H 41" 8 150.00 1,200.00 380 Piece Disposal Bins (trash Bins 75 L) 3 2,000.00 6,000.00 381 Piece Dressing Mirror (whole Body Mirror With 4 Wheels Height 5ft. Width 14 Inches) 1 1,500.00 1,500.00 382 Piece Drying Rack (78cmx46cmx185cm) 2 2,500.00 5,000.00 383 Piece Dust Catcher With Broom (2n1 Broom Dustpan Set Windproof Floor Sweeper With Broom) 10 170.00 1,700.00 384 Piece Feather Duster (soft Magic Feather Duster Long Size And Colorful Colors (plastic) 10 150.00 1,500.00 385 Piece First Aid Cabinet, Plastic Box 30cmx12cmx30co With Transparent Cover (free Installation) 2 1,500.00 3,000.00 386 Piece Flat Iron (non-stick Teflon Sole Plate Spray Function Ht &width 251x170x120mm) 3 1,500.00 4,500.00 387 Piece Floor Mop (magic Spin Mop With Bucket 360° Rotating Floor Cleaning Plastic Liner) 10 1,000.00 10,000.00 388 Piece Hair Razor (twin Blade Disposable Razors) 100 30.00 3,000.00 389 Dozen Hangers (12 Piece. Plastic Hanger) 2 300.00 600.00 390 Set Housekeeping Cart. Multi-functional Movable Cleaning Cart Housekeeping Property Cleaning Tool Cart Special Trolley. Standard For Housekeeping Work. 2 5,000.00 10,000.00 391 Piece Ironing Board (ironing Board With Stand Portable 43"iron Board (70cm To 86 Cm) 3 1,300.00 3,900.00 392 Set Laundry Bag Set (4 Piece/set Laundry Washing Bag- 1 Pc M(30cmx40cm) 1pc L (40cmx50cm) 1pc Xl (50x60 Cm) 5 150.00 750.00 393 Piece Nail Clipper (stainless Nail Clippers H-8 Cm Wt-0.046 Kg) 20 100.00 2,000.00 394 Set Nail File (12-piece Red Nail File (medium) 20 50.00 1,000.00 395 Piece Non-slip Doormat 75x45 Cm Rubber 18 500.00 9,000.00 396 Piece Pail (utility Pail With Metal Handle 10l/26x27 Cm) 7 300.00 2,100.00 397 Set Shopping Cart Utility Cart Trolley Grocery Cart For Warehouse Garden Supermarket 2 6,000.00 12,000.00 398 Piece Sponge (high Density Double-sided Dishwashing 7x10x3 Cm) 20 30.00 600.00 399 Piece Spray Bottle (garden Sprayer Capacity: 500ml) 10 170.00 1,700.00 400 Piece Trash Can (with Plastic Swing Lid L-27 Cm, W- 17.5cm, H- 40.5 Cm) 8 260.00 2,080.00 401 Piece Wash Basin (laundry Basin 23-inch, Aluminum Made) 3 300.00 900.00 402 Piece Adaptive Swim Life Jacket For Disabled Keeps The User’s Face Out Of The Water Stops The Tension Of The Neck, Upright Position Back Support, Therapist Hands Free, No Latex Double Harness Distributes Tension’s Adjustment. Possibility To Add The Harness Pad (or “cuissard” In French) 2 11,000.00 22,000.00 403 Piece Bed Foam (for Single Bed, 3 Inches Thick) 1 3,500.00 3,500.00 404 Piece Bed Sheets- Material: Cotton+polyester, Packaging Content: 2-piece Pillowcase, 1 Pc Fitted Sheet, Single Size:36"*75"+7.8", Pillowcase Sice: 18'*28", Gartered Corners 10 2,000.00 20,000.00 405 Piece Bedsheets (cotton Full Gartered 3n1 Bed Sheets, L-60in Ww-75in (for Single Bed Size) 10 300.00 3,000.00 406 Piece Blanket (cotton Full Gartered 3n1 Bed Sheets, L-60in Ww-75in (for Single Bed Size) 10 300.00 3,000.00 407 Piece Blankets- Length: 160 Cm White Sheet Soft Texture, High Quality Fabric Size: 52 X 90 Inch 20 450.00 9,000.00 408 Piece Cervical Pillow. Memory Foam Pillows Contour Memory Foam Pillow For Neck Pain Relief, Orthopedic Neck Bed Pillow For Side Sleepers Back And Stomach With Pillowcase, Removable, Washable 2 2,000.00 4,000.00 409 Set Dish Towels (10 Pc. Per Set 25 Cm X 25 Cm Microfiber Super Absorbent) 20 1,000.00 20,000.00 410 Piece Dri-fit T-shirt, Color White For Sublimation Printing, Size: Extra Large 150 150.00 22,500.00 411 Piece Dri-fit T-shirt, Color White For Sublimation Printing, Size: Extra Small 150 150.00 22,500.00 412 Piece Dri-fit T-shirt, Color White For Sublimation Printing, Size: Large 200 150.00 30,000.00 413 Piece Dri-fit T-shirt, Color White For Sublimation Printing, Size: Medium 200 150.00 30,000.00 414 Piece Dri-fit T-shirt, Color White For Sublimation, Size: Small 150 150.00 22,500.00 415 Piece Face Towel (basic Face Towel - Free Size) 20 100.00 2,000.00 416 Piece Foam Rolls- Material: Expanded Polypropylene Foam Item Weight: 0.42 Pounds, Size: 18 Inches X 8ft. 5 4,000.00 20,000.00 417 Piece Foam. Size:36"x75"; Materials: Polycotton; Thickness: 6" 10 7,000.00 70,000.00 418 Piece Life Jackets For Kids’ Premium Neoprene Safety Life Jacket 5 600.00 3,000.00 419 Pair Pediatric Examination Gowns- Assorted For Kids And Adult Pediatric Examination Gowns Opening: Full Open Back. Style: Child Size Color: Jellybean Print. Made With High Quality, 100% Cotton Comfortable, Durable, Washable, And Reusable Hook And Loop Closures At Neck And Mid-back. 10 700.00 7,000.00 420 Piece Pillowcase- Length: 50 Cm (20 ") Pillowcase Quantity: 1 Piece Width: 80 Cm (31 ") 100 % Polyester 20 180.00 3,600.00 421 Piece Pillows- Pillows, Plain White, Soft Pillow, Size:18x28 Inches 10 900.00 9,000.00 422 Piece Socks (cotton Socks Unisex High Street Socks Sixe:38-44) 5 100.00 500.00 423 Piece Towels- Material: High Quality 100% Cotton Terry. 500gm2. Size: 90 X 180cm. 20 300.00 6,000.00 424 Piece Wash Rags (round Rags) 20 30.00 600.00 425 Piece Welding Gloves 3 500.00 1,500.00 426 Piece Welding Hood Cape (standard Size) 3 500.00 1,500.00 427 Piece Welding Protective Suite (genuine Whole Leader Welding Apron) 3 2,362.00 7,086.00 428 Set Doll Mannequin Kid: Female Material: Plastic Age Group: Children- 3 To 6 Years Old Mannequin Type : Full Body Base : Glass Base Style : Stand Size:height:107cm.shoulder-29cm.chest:57cm, Waist 53cm Packing: Wrapped 1pc/carton Color: Skin Tone Color 2 4,000.00 8,000.00 429 Set Doll Mannequin Kid: Male Material: Plastic Age Group: Children- 3 To 6 Years Old Mannequin Type : Full Body Base : Glass Base Style : Stand Size:height:107cm.shoulder-29cm.chest:57cm, Waist 53cm Packing: Wrapped 1pc/carton Color: Skin Tone Color 2 4,000.00 8,000.00 430 Set Doll Mannequin. Plastic Whole Body With Stand Decor Body Dress Full Body Display Female Height:185cm 2 5,000.00 10,000.00 431 Set Doll Mannequin. Plastic Whole Body With Stand Decor Body Dress Full Body Display Male Height:185cm 2 5,000.00 10,000.00 432 Piece Povidine-iodine 120ml (antiseptic Wound Solution) 5 250.00 1,250.00 433 Piece Deodorant (roll On 50 Ml Bottle) 5 200.00 1,000.00 434 Pack Detergent Powder 3kgs 5 500.00 2,500.00 435 Pack Feminine Napkin (silk Floss 12 Piece) 10 50.00 500.00 436 Piece Gauze Bandage (sterile Gauze Bandage 3x10 Per Box) 2 300.00 600.00 437 Gal. Liquid Soap, Paraben-free, Sulfate-free, Anti-aging, Anti-bacterial, Moisturizing, 1 Gallon 5 500.00 2,500.00 438 Piece Chlorine Tablet For Swimming Pool, Pack Of 300-piece 3-inch Tablet Adjustable Chlorine Dispenser 8 Inch In Combination With Mont Package Included:1*chlorine Dispenser +300 Piece Cleaning Tablet 20 500.00 10,000.00 439 Piece Table Napkin (2 Ply 40s Sheets Folded) 10 50.00 500.00 440 Roll Artificial Grass. 2mx25m Simulation Lawn Carpet Grass Garden Outdoor Rug Synthetic Thick Lawn 30mm Thick 4 20,000.00 80,000.00 441 Piece Fire Extinguisher 3lbs Abc Dry Chemical Refillable (free Installation) 4 3,000.00 12,000.00 442 Piece Artist Stool With Wheels (stainless Steel Stool Bar) 2 1,991.00 3,982.00 443 Piece Artist Taboret (35 ½" H X 17 ½" W X 14 ½" D+9/cm X 44cm X 37 Cm) 1 24,728.00 24,728.00 444 Piece Convertible Drawing And Drafting Table (manual Lift Dimension W-7.75 X D 24x H22" To 31.5") 3 8,400.00 25,200.00 445 Piece Drawing Lamp (metal Adjustable Arm Work Desk Lamp) 5 500.00 2,500.00 446 Piece Medicine Cabinet Large. Dimension: 29 X16.5x16 Cm 2 1,500.00 3,000.00 447 Piece Monoblock Chairs Color Green 200kg Capacity Size (39.5 Cmx86.5 Cmx39.5 Cm) 50 700.00 35,000.00 448 Piece Monoblock Chairs For Kids (specs: Color White, Dimension: Seat Height:212mm, Seat Width:256mm, Seat Depth:200mm) 15 300.00 4,500.00 449 Piece Multi-layer Wooden Bookshelf For Toddler (specs: 1m H X 1.5m W; Premium Cotton Canvass Material And Made Of Wood) 1 2,000.00 2,000.00 450 Piece Rectangular Table For Kids (specs: 77x55 Cm,color Red) 8 1,500.00 12,000.00 451 Piece Stack Rack (toy Origami Rack Shelves) 5 1,477.00 7,385.00 452 Piece Storage Box With Handle, Material: Plastic, Capacity: 20 L , Color: Transparent Clear( Lxwxh) 44x 31x22 29 300.00 8,700.00 453 Unit Treatment Table- Top Shelf With Guard Rail And Formica Material. Down Shelf, Material Plain Sheet. Mounted On 4 Swivel Caster Rubber Wheels 2″ With 2 Pieces Lock. Size: Lxwxh (28″x20″x34.5″), Painted White 1 17,400.00 17,400.00 454 Ream Art Paper (assorted Colors, 8.5"x11") 5 270.00 1,350.00 455 Piece Binder Clip 2" 200 20.00 4,000.00 456 Ream Bond Paper 13x8.5" Subs. 20 50 320.00 16,000.00 457 Ream Bond Paper A4 Subs. 20 50 300.00 15,000.00 458 Piece Clear Book, Long 8.5"x13", Color Violet 100 150.00 15,000.00 459 Piece Clip Board Long (specs: 23x35cm, Plastic Or Wooden) 30 200.00 6,000.00 460 Set Colored Pencils (colored Pencils 12/set) 5 190.00 950.00 461 Set Colored Pens (fine Line Colored Marker 24 Colors In Pvc Bag) 5 90.00 450.00 462 Piece Cork Bulletin Board (20x30cm Cork Board With Black Wooden Frame) 3 800.00 2,400.00 463 Set Crochet Hooks (100-piece Crochet Hook) 10 300.00 3,000.00 464 Roll Crochet Thread Hand Knitting, Crochet Single Color (blue) 5ply 50g 10 80.00 800.00 465 Roll Crochet Thread Hand Knitting, Crochet Single Color (green) 5ply 50g 10 80.00 800.00 466 Roll Crochet Thread Hand Knitting, Crochet Single Color (orange) 5ply 50g 10 80.00 800.00 467 Roll Crochet Thread Hand Knitting, Crochet Single Color (white) 5ply 50g 10 80.00 800.00 468 Roll Crochet Thread Hand Knitting, Crochet Single Color (yellow) 5ply 50g 10 80.00 800.00 469 Roll Crochet Thread Hand Knitting, Crochet Single Color (black) 5ply 50g 10 80.00 800.00 470 Roll Crochet Thread Hand Knitting, Crochet Single Color (red) 5ply 50g 10 80.00 800.00 471 Piece Cutter - Snap Off Blade Knife Blade, Refill 9 Mm 20 13.00 260.00 472 Set Double Deadbolt Door Lock Chassis: Stainless Steel Latch Or Bolt: Stainless Steel Cylinder Housing: Steel Backset: 60mm Or 70mm Door Thickness: 35-50 Mm For Essential Double Lock - Use Keys To Open/lock With 3 Keys 25 1,500.00 37,500.00 473 Piece Easel For Painting (wooden Easel Stand For Painting 1.75m Complimentary Screws Firm And Strong) 5 454.00 2,270.00 474 Set Envelop Long Brown (100 Piece) 8.5"x13" 310 300.00 93,000.00 475 Piece Expanded Envelope, Long Color Brown 100 60.00 6,000.00 476 Piece File Folders. (black Or White) Model: Minimum Of 100 Pages Capacity Size: 310*235mm, Suitable For School And Office Supply 20 500.00 10,000.00 477 Piece Glue Gun. 3.6v Cordless Hot Melt Glue Gun Rechargeable Fast Glue Gun Kit With 20-piece Glue Stick Automatic-power-off 15 1,600.00 24,000.00 478 Box Jumbo Crayons (pack Of 8) 160 200.00 32,000.00 479 Piece Knitting Needles (2 Piece/set (35cm) Knitting Sweater Stick Needle Bamboo Sweater Needle Knitting Scarf Tool) 5 200.00 1,000.00 480 Pack Laminating Pouches Long 13", 250 Micron, 100 Pouches Size: 222mmx337mm 7 2,000.00 14,000.00 481 Unit Learners'/clients' Chart Materials- A4 Size 8-1/4 X 11-3/4 Inches Or 210 X 297 Mm Or 29.7 X 21 Cm Laminated Full Color High Quality Print Photopaper 20 80.00 1,600.00 482 Piece Magnetic Aluminum Whiteboard (specs:35x50cm) 5 300.00 1,500.00 483 Piece Meter Stick, 100cm Stainless Steel Ruler 5 500.00 2,500.00 484 Gal. Multi-purpose White Glue 1 Gal. 5 1,000.00 5,000.00 485 Box Paper Clips (vinyl Coated Assorted Size By 100piece) 40 250.00 10,000.00 486 Piece Paper Tray (specs: 5layer, Long Bond Paper Rack,39x28x7cm) 3 500.00 1,500.00 487 Piece Pencil No. 2 400 10.00 4,000.00 488 Piece Pencil Sharpener Heavy Duty (item Dimension: Stainless Steel Body, 11.5x6.5x6.5) 11 500.00 5,500.00 489 Piece Permanent Marker (specs: Black, Broad And Fine) 220 50.00 11,000.00 490 Pack Pvc Cards Sheets, 50 Sets (100 Pvc Films And 50 Pvc Cards) Size: 200mmx300mm 30 3,000.00 90,000.00 491 Piece Record Book. 8.5"x13" By 200 Pages 12 300.00 3,600.00 492 Piece Sand Eraser For Ink And Pencil E-330 300 15.00 4,500.00 493 Piece Scissors, 5" Blunted Scissors, Plastic Handle. 20 200.00 4,000.00 494 Set Sewing Thread (polyester 1000 M) Assorted Color 10 200.00 2,000.00 495 Piece Sign Pen (assorted Color, Number 0.5) 250 20.00 5,000.00 496 Unit Spiral Binding Machine F4 Size S40m 40 Holes Heavy Duty [long/legal], Binding Form: Spiral / Coil , Pitch: 4:1 Size: F4 / Long / Legal Maximum Punching: 15 Sheets (70gsm Paper) Per Manual Punch Maximum Binding Capacity: 450 Sheets (70 Gsm Paper) Adjustment Margins: 2.5, 4.5, 6.5mm Number Of Holes: 40 Holes , Hole Distance: 8.47mm Size Of Machine: 425x230x270mm , Net Weight: 5.5kg 1 7,000.00 7,000.00 497 Unit Stapler Heavy Duty (ds-425) 20 150.00 3,000.00 498 Piece Sublimation Coated White Mug 11oz Sublimation Printable (blank) 500 60.00 30,000.00 499 Piece Sublimation Plain Trucker Mesh Net Cap 200 60.00 12,000.00 500 Piece Tailor’s Scissors (10") Heavy Duty 5 1,500.00 7,500.00 501 Piece Tape Dispenser Size:1" 10 1,500.00 15,000.00 502 Piece Tape Measure (body Tape Measuring Ruler Tailoring) 5 50.00 250.00 503 Piece Watercolors (50 Color Solid Watercolors Tin Box (202'82'33mm) 5 441.00 2,205.00 504 Pack Whiteboard Marker, Black. 3piece Per Pack (refillable) 100 150.00 15,000.00 505 Piece Whiteboard Marker (specs: Blue, Red And Black, Fine) 170 70.00 11,900.00 506 Roll Yarn (yarn Hand Knitting And Crochet Single Color (blue) 5ply 50g 50 80.00 4,000.00 507 Roll Yarn (yarn Hand Knitting And Crochet Single Color (green) 5ply 50g 50 80.00 4,000.00 508 Roll Yarn (yarn Hand Knitting And Crochet Single Color (orange) 5ply 50g 50 80.00 4,000.00 509 Piece Yarn (yarn Hand Knitting And Crochet Single Color (red) 5ply 50g 50 80.00 4,000.00 510 Roll Yarn (yarn Hand Knitting And Crochet Single Color (white) 5ply 50g 50 80.00 4,000.00 511 Piece Yarn (yarn Hand Knitting And Crochet Single Color (yellow) 5ply 50g 50 80.00 4,000.00 512 Box Braille Paper. 11.5"x 8.5". 1000 Sheets 5 7,000.00 35,000.00 513 Box Braille Paper. White Fanfold Tractor-feed Braille Transcribing Paper: 11.5 X 11.5 Inches, 3-hole, And 19-hole Punch. Dimensions:10.1 × 11.5 × 5.4 Inches. 1000 Sheets 5 10,000.00 50,000.00 514 Box Swell-touch Paper 11 X 11.5-in- 100 Sheets 2 10,000.00 20,000.00 515 Piece Basketball, Standard Size 2 2,000.00 4,000.00 516 Set Bocce Balls, 100mm Diameter, 4 Balls Colored Red, 4 Balls Colored Green, With Palena Ball Color White. Set With Bag. 2 20,000.00 40,000.00 517 Piece Goalball, Standard Size, And Weight, Blue 2 20,000.00 40,000.00 Assistive Devices And Equipment Shall Be Provided With At Least 1 Year Warranty And After-sales Service. Delivery Terms: Within 30 Days Drop Off Points: General Santos City Sped Integrated School – Quezon Avenue, Brgy. West, Gsc (ilrc) Payment Terms: Payment To The Service Provider Shall Be Made Through Philippine Veterans Bank Lddap-ada / Mds. In The Case Of Accounts Maintained In Other Bank, Bank Transfer Fees Shall Be Chargeable Against The Creditor’s Account. ***nothing Follows*** Subtotal 7,049,507.00 Grand Total 7,338,507.00 2. Deped Sdo Of General Santos City, Through Its Bids And Awards Committee (bac), Now Invites Bids For The Above Procurement Project. 3. Bidding Will Be Conducted Through Competitive Bidding Procedures Using A Non-discretionary “pass/fail” Criterion As Specified In The Implementing Rules And Regulations (irr) Of Republic Act (ra) 12009, Otherwise Known As The “new Government Procurement Act” With The Following Eligibility Requirements: A. Valid And Updated Philgeps Certification (platinum) From The Sole Proprietorships, Partnerships, Corporations, Cooperatives And Persons/entities In The Form Of Joint Venture; B. Statement Of The Bidder Of All Its Ongoing Government And Private Contracts; C. Statement Of The Bidder’s Slcc Similar To The Procurement Project Which Is 50% Of The Abc Or A Combination Of Contacts: (i) At Least One (1) Similar Contract Amounting To At Least 25% Of The Abc And (ii) Other Contracts, Whether Similar Or Not, With An Aggregate Amount Of At Least 25% Of The Abc, Provided Their Total Value Is At Least 50% Of The Abc. D. The Bidder’s Computation Of Nfcc Which Is Equal To The Abc Or A Committed Line Of Credit From A Bank With At Least 10% Of The Abc; E. Jva Or The Duly Notarized Statement In Accordance With Section 52.1(b) Of The Irr, If Applicable; F. Bid Security In The Prescribed Form, Amount And Validity Period; G. Technical Specifications H. Omnibus Sworn Statement I. Original And Signed Copy Of The Bid Form 4. The Contract Will Be Awarded To The Supplier Determined To Have The Single Or Lowest Calculated And Responsive Bid (s/lcrb) Based On The Above Final Technical And Financial Requirements. 5. A Complete Set Of Bidding Documents In Soft Copy Only May Be Purchased At Deped-division Of General Santos City Bac Secretariat, Located At Tiongson St., Lagao, General Santos City Upon Submission Of A Letter Of Intent, And Payment In Cash On A Non-refundable Fee By Interested Bidders To The Deped Division Cashier. Only Bidders Who Purchased The Bidding Documents Provided Below Shall Be Allowed To Submit Bid/bids Not Later Than The Scheduled Receipt And Opening Of Bids Bidding Document Price Lot Number Price Lot No. 1 P 500.00 Lot No. 2 P 10,000.00 6. It May Be Viewed Or Downloaded After Payment From The Website Of The Philippine Government Electronic Procurement System (philgeps), Www.philgeps.gov.ph. The Schedule And Venue Of The Procuring Activities Are As Follows: Activity Date And Time Venue Pre-bid Conference April 21, 2025 2:00 P.m. (monday) Sds Conference And Online Via Google Meet Issuance Of Bidding Documents Until May 5, 2025 1:00 P.m. (monday) To Be Sent To Bidder’s Email Address After Payment Of The Bidding Documents Receipt And Opening Of Bids May 5, 2025 2:00 P.m. (monday) Division Office/google Meet The Pre-bid Conference Is Open To All Interested Parties Who May Have Or Have Not Bought The Bidding Documents. 7. Bids Must Be Physically Delivered To The Address And On The Date And Time Stated Herein. Submission Of Digital Copy Of The Bidding Documents Shall Not Be Accepted. All Bids In Modes Of Procurement That Are Competitive In Nature Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Section 56.2 Of The Irr. 8. Bids Will Be Opened In The Presence Of The Bidder’s Representatives Who Choose To Attend The Opening Of Bids At The Address, Date And Stated Herein. Late Bids Shall Not Be Accepted. 9. For Further Information, Please Refer To: Ofelia S. Panes Michael Jhon A. Del Sol Administrative Officer Iv (records) Administrative Assistant Ii Bac Secretariat Head Bac Secretariat Member Email: Ofelia.panes@deped.gov.ph Email: Bac.depedgensan@deped.gov.ph Cell No. 09692673871 Cell No. 09278865516 Approved By: Mervie Y. Seblos, Cese Oic – Assistant Schools Division Superintendent Bac Chairperson Bacsec/mds

Details: Description Invitation To Bid For The Procurement Of Technical-vocational- Livelihood (tvl) Equipment Packages To Public Senior High Schools Of The Division Of Surigao Del Sur With Approved Budget For Contract Worth Sixteen Million, Five Hundred Eighty Thousand And Twenty Seven Pesos (16,580,027.00) Stock No. Unit Item Description Quantity Unit Total Cost Cost Lot A: Cookery 1 Apple Corer Type: Apple Corer Body Shape: Tubular Material: Stainless Steel Total Length: 18 Cm (minimum) Handle Material: Hard Plastic, Polypropylene Handle Dimension: Length-10 Cm X Diameter-2 Cm (minimum) Blade Size: Length-8cm X Diameter-2 Cm (minimum) Preferably With Packing Case Dishwasher Safe 44 834 36,696.00 2 Pc Bain Marie,table Type: Bain Marie Table (food Warmer) Body Shape: Rectangular Material: 304 Stainless Steel, 0.8 Mm Thick (minimum) Dimensions: Length-1500 Mm X Width-700mm X Height-800 Mm (minimum) Power Soiuce: Voltage: 220 Volts - 230 Volts, 50 Hz/ 60 Hz With Royal Cord 1.5 Meter Long With Attachment Standard Type A Male Plug Or Provide Plug Adopter 10a/220v 11 15099 166,089.00 3 Pc Blender, Electric Type: Blender Machine Body Shape: Round Jar Material Housing: Plastic (polypropylene) Jar Height : 25 Cm To 28 Cm Jar Thickness: 4 Mm To 8 Mm Heat Resistant Glass Jar With Cover Source Voltage: 220 Volts / 240 Volts,50 Hz / 60 Hz With Power Cord 1.5 Meter Long With Attachment Of Standard Type A Male Plug Or Provide Plug Adopter 10a/220v. Power Wattage: 300 To 700 Watts Blade: Stainless Steel, 3 To 4 Metal Blades 11 5,000 55,000.00 4 Pc Board, Chopping/cutting, Plastic Type: Cutting Board Body Shape: Rectangular Material: Plastic (polypropylene), Food Grade Board Size: Length: 15 Inches (minimum) Width: 12 Inches (minimum) Thickness: 0.5 Inch (minimum) With Hole For Storage Purposes Preferably With Packing Case Food Grade And Dishwasher Safe 176 310 54,560.00 5 Pc Boiler, Double Material: Stainless Steel Thickness: 1/16 Inch (1.5 Mm) (minimum) Lid Material: Glass Rivetedhandle On Both Side Diameter: 9 1/2 Inches (minimum) Total Height: 9.4 Inches (minimum) Inset Bottom Diameter: 9 Inches (minimum) Inset Top Diameter: 9 Inches (minimum) Capacity: 2 Liters (minimum) 11 11000 121,000.00 6 Pc Braising Pan, Medium Type: Braising Pan Body Shape: Round Material: Enameled Cast Iron And Stainless Steel Size: Diameter: 28 Cm X Height: 10 Cm (minimum) Capacity: 4 Liters (approximate) With Stainless Steel Cover, Solid Cast Stainless Steel Side Handles And Riveted Handle On Both Side: Length: 10 Cm (minimum) Handle Diameter: 8 Mm To 10 Mm 88 438 38,544.00 7 Pc Can Opener Type: Can Opener Body Shape: Materials: Stainless Steel Dimension: Length-21 Cm X Width 10 Cm X Depth:2.5cm (minimum) Multi-use: 3 In 1 Can Opener Also Opens Bottle Tops- Can Lids And Tabs 11 465 5,115.00 8 Pc Casserole, Medium Type: Casserole Pot Body Shape:round Material:stainless Steel, 0.7 Mm Thick Dimension: Diameter- 24 Cm X Height -14 Cm (minimum) Tempered Glass Lid Welded Handle On Both Sides, Size: 7.5 Cm (minimum) Handle Diameter: 8 Mm To 10 Mm Preferably With Packing Case 44 6399 281,556.00 9 Pc Casserole, Small Type: Casserole Pot Body Shape: Round Material: Stainless Steel, 0.7 Mm Thick Dimension: Diameter- 20 Cm X Height -12 Cm (minimum) Tempered Glass Lid Welded Handle On Both Sides, Size: 7.5 Cm (minimum) Handle Diameter: 8 Mm To 10 Mm 132 3709 489,588.00 10 Pc Colander, Medium Type: Colander, Medium Body Type: Round Material: 304 Stainless Steel Diameter: 30 Cm (minimum) Capacity: 8 Quarts (9 Liters) Welded Handle On Both Sides, Size: 7.5 Cm (minimum) Handle Diameter: 8 To 10 Mm Body Thickness: 0.8 Mm (minimum) 22 579 12,738.00 11 Pc Colander, Small Type: Colander (small) Body Shape: Round Material: 304 Stainless Steel Diameter: 26 Cm (minimum) Capacity: 5 Quarts (5.6 Liters) Welded Handle On Both Sides, Size: 7.5 Cm (minimum) Handle Diameter: 8 Mm To 10 Mm Body Thickness: 0.8 Mm (minimum) Full-ring Support Base, 15 Cm Diameter Preferably With Packing Case Food Grade And Dishwasher Safe 44 438 19,272.00 12 Pc Cup, Measuring (for Solid) Type: Measuring Cup Set Body Shape: Round Material: Stainless Steel, 0.7 Mm Thick (minimum) Each Set Contains The Following: 1 Pc - 1 Cup (237 Ml) 1 Pc - 1/2 Cup (118 Ml) 1 Pc - 1/3 Cup (79 Ml) 1 Pc - 1/4 Cup (59 Ml) Handle Dimension: Length-12 Cm X Width-1 Cm (minimum) Measuring Capacity Engraved On The Handle Strip Handles Have Provision For Hanging Preferably With Packing Case Smooth Surfaces And Dishwasher Safe 88 490 43,120.00 13 Pc Dispenser, Paper Towel Type Paper Towel Dispenser Body Shape: Rectangular Material: Abs Plastic Dimensions: Length =260 Mm X Width =100 Mm X Height = 211 Mm (minimum) Capacity: 200 Paper Paper Size: Length-20 Cm X Width- 8 Cm (approximate) Mounting Style: Wall Mounted Tissue Box 44 250 11,000.00 14 Pc Fan, Electricfan Stand Fan, Electric Material: Metal, Plastic Size/diameter: 18 Inches Power Rating: 70 Watts (minimum), 220 / 240 Vac, 50 / 60 Hz, Single Phase Rotation Angle: 90 Degrees Base: Stable, 16 Inches Diameter (approx.) Removable Metal Guard On Front And Rear 3-speed Settings Comes With 1.5 Meters Power Cord And With Molded Male Plug To Adapt Type A Outlet (or Providing 3a Minimum Plug Adapter Is An Option) Smooth Surface, No Sharp Edges Includes User's Manual In English Which Contains: A. A Diagram Of The Parts With Their Names, 11 5200 57,200.00 15 Pc Fire Extinguisher (with Contents) 1.for Type A, B, C Fire: Dry Chemicals (monoammonium Phosphate) 2.portable Type 3.capacity : 5 - 6 Kgs 4.rechargeable Cylinder Metal 5.working Pressure Of Cylinder : 400 Psi 6.brass Valve With Pressure Gage 7.with Rubberized Hose And Aluminum Nozzle Attached 8.with Squeeze Lever To Discharge And Safety Pin 10.painted With Metal Primer And Red Enamel Paint 11 8000 88,000.00 16 Pc Fish Poacher, Medium Type: Fish Poacher Body Shape: Oval Pot For Poaching Material: Stainless Steel, 0.64 Mm Thick Dimensions (l X W X D): 45 Cm X 15 Cm X 12 Cm (minimum) Handle Material: Stainless Steel Riveted Looped Handles On Both Side, 7 Cm (minimum) Handle Diameter: 8 Mm To 10 Mm Includes Stainless Steel Lid With Handle And Removable Insert 11 3745 41,195.00 17 Pc Fork, Carving Type: Carving Fork Body Shape: Square Shape Prong Prong Material:high Carbon Stainless Steel Overall Length: 30 Cm (minimum) Blade Dimension: Length- 15 Cm X Width- 0.5 Cm X Thickness- 0.3 Cm (minimum) Number Of Prongs: 2 Prong Comes With Square- Shaped Prongs And Pointed Tips Abs Plastictriple-riveted Handle Preferably With Packing Case 33 812 26,796.00 18 Pc Fork, Kitchen Type: Kitchen Fork Body Shape: Standard Material: Stainless Steel Dimension: Length - 32 Cm X Width- 3.5 Cm (minimum) Fork Size: Length: 8 Cm X Width -3.5 Cm (minimum) Handle :abs Plastic Number Of Tines: 2 Tines With Tapered End 88 435 38,280.00 19 Pc Frying Pan, Large Type: Frying Pan (large) Body Shape: Round Pan Material: Aluminum With Non-stick Coating Thickness: 3 Mm Thick (minimum) Dimension: Diameter-30 Cm (minimum) X Height- 5.5 Cm (minimum) Handle Material: Stainless Steel With Silicone Riveted Handle: 20 Cm Long (minimum) Preferably With A Packing Case Oven Safe Up To 250⁰f 22 5499 120,978.00 20 Pc Frying Pan, Medium Type: Frying Pan (medium) Body Shape: Round Pan Material: Aluminum With Non-stick Coating Thickness: 3 Mm Thick (minimum) Dimension: Diameter-24 Cm (minimum) X Height- 4.5 Cm (minimum) Handle Material: Stainless Steel With Silicone Riveted Handle: 19 Cm Long (minimum) Preferablywith A Packing Case 88 3299 290,312.00 21 Pc Frying Pan, Small Type: Frying Pan (small) Body Shape: Round Pan Material: Aluminum With Non-stick Coating Thickness: 3 Mm Thick (minimum) Dimension: Diameter-20 Cm (minimum) X Height- 3.8 Cm (minimum) Handle Material: Stainless Steel With Silicone Riveted Handle: 12 Cm Long (minimum) Preferably With A Packing Case Oven Safe Up To 250⁰f 132 2,499.00 329,868.00 22 Pc Funnel, S/s,, Medium Type:stainless Steel Funnel Body Shape: Round Material: 304 Stainless Steel Dimension: Diameter-15 Cm (minimum) X Height- 15.8 Cm (minimum) Tube Diameter: 2 Cm X Length: 7.3 Cm (minimum) Comes With Handle For Easy Hanging Preferably With Packing Case Dishwasher Safe 44 356.00 15,664.00 23 Pc Funnel, S/s, Small Type: Stanless Steel Funnel Body Shape: Round Material: 304 Stainless Steel Dimension: Diameter-11 Cm (minimum) X Height- 10 Cm (minimum) Tube Diameter: 1.5 Cm X Length: 5 Cm (minimum) Comes With Handle For Easy Hanging Preferably With A Packing Case Dishwasher Safe 44 246.00 10,824.00 24 Pc Garbage Bin Type: Swivel Lid Garbage Bin Body Shape: Round Material: Hard Plastic, Polypropylene Dimension: Diameter-26 Cm X Height-47 Cm (minimum) Capacity: 4 Gallons (minimum) Removable Dome Shape Lid With Spring Return Swivel Preferably With A Packing Case Color: Any Color 44 432.00 19,008.00 25 Pc Glass Rack Type: Glass Rack Body Shape: Square Material: Polypropylene Plastic Overall Dimensions: Length - 19 1/2 Inches X Width - 19 1/2 Inches X Height - 4 Inches (minimum) Compartments: Full-size 25 Individual Compartment Glass Rack Compartment Dimensions: Length - 3 1/2 Inches X Width - 3 1/2 Inches X Height - 4 Inches (minimum) Easy Grip Handles Molded Into All Four Sides Preferably With A Packing Case 132 3,093.00 408,276.00 26 Pc Ice Cream Scooper Type: Ice Cream Scooper Body Shape: Round Material: Stainless Steel Scoop: Diameter- 5 Cm X Deep-2.5 Cm (minimum) Handle Length: 10 To 12 Cm With Trigger Spring Handle And Scoop Scraper Mechanism 22 374.00 8,228.00 27 Pc Knife, Boning Type: Flexible Boning Knife Body Shape: Ergonomic Material: High Carbon Steel Overall Length: 28 Cm (minimum) Blade: Length-15 Cm X Width- 3 Cm (minimum), Pointed Tip Cutting Edge Angle From Tip To The Heel Is 13 To 14 Degrees Handle Length: 12 Cm (minimum) Handle Material: Hard Plastic Handle With Rivets Preferably Wiht Packing Case Dishwasher Safe 88 459.00 40,392.00 28 Pc Knife, Chef Type: Chef's Knife Body Shape: Flat Materials: Stainless Steel Overall Length: 30 Cm (minimum) Blade Size: Length - 20 Cm X Width-4 Cm (minimum) Blade Thickness: 2.5 Mm (minimum) 110 808.00 88,880.00 29 Pc Knife, Cleaver Type: Cleaver Knife Body Shape: Flat Blade Material: Forged Stainless Steel Heavy Duty Blade Length: 17 Cm (minimum) Overall Length: 30 Cm (minimum Cutting Edge: Straight Handle Material: Ergonomic Wood Handle With Triple Rivets 22 1,274.00 28,028.00 30 Pc Knife, Oyster Type: Oyster Knife Body Shape: Ergonomic Blade Material: Stainless Steel Blade Dimension: Length - 7 Cm (minimum) X Width - 2 Cm (minimum) Blade Thickness: 2 Mm (minimum) Handle Material: Smooth Wooded Handle Rounded Handle Size: Length-10 Cm X Diameter- 3.5 Cm (minimum) Total Length (from The Tip Of The Handle Up To Tip Of The Blade) :17 Cm (minimum) 44 514.00 22,616.00 31 Pc Light, Emergency Emergency Light, 2 Heads Led Materials: Metal, Anti-rust Coated Duration Time (2 Heads): 5 Hours (minimum) Automatically Light Up During Power Outage Overcharge And Over- Discharge Protection Built - In Ac Charger, Power Cord Plug To Adapt Type A Outlet (or Providing 5a Minimum Plug Adapter Is An Option) Battery Test Switch - External Safety Fuse Head: White Led 1w (minimum) 3.5 " Dome Reflector 11 1,141.00 12,551.00 32 Pc Meat Slicer Type: Meat Slicer Body Shape: Circular Housing Material: Die Cast Aluminum Alloy And Body Painted Dimensions: Width-40.5 Cm X Depth- 45.7 Cm X Height- 38 Cm (minimum) Stainless Steel Rotary Blade Diameter: 190 Mm (minimum) Power Source: 220 Volts-230 Volts, 60 Hz With Power Cord 1.5 Meter Long With Attachment Of Standard Type A Male Plug Or Provide Plug Adopter 10a/220v 11 18,000.00 198,000.00 33 Pc Pastry Tool Must Be Branded. Tube, Pastry Cookery Nc Ii Type: Pastry Tubes Body Shape: Tube In Different Shape Of Nozzles Material: Stainless Steel Set Contain: 24 Different Shapes Of Nozzles (minimum) Tube Height: 3.5 Cm To 5 Cm Tube Diameter: 2 Cm To 3.5 Cm Thickness: 0.5 Mm (minimum) Tube Tip: Assorted Designs (create Swirls, Rosettes, Flowers, Stars, Leaves And Other Designs 88 301.00 26,488.00 34 Pc Peeler, Y-type Type: Y-type Peelers Body Shape: Ergonomic Material: Stainless Steel Overall Dimensions (l X W X H): 7 Inches X 2 1/4 Inches X 1 Inch (minimum) Blade Material: 304 Stainless Steel, 0.7 Mm Head Dimension: (l X W X H) 2 1/4 Inches X 2 1/4 Inches X 1 Inch (minimum) Handle Material: Stainless Steel Handle Length: 4 3/4 Inches X 1 Inch Diameter (minimum) 2 In 1 Design With 2 Blade Reel, Built In Potato Eye Remover And Hole For Hanger Preferably With A Packing Case 88 245.00 21,560.00 35 Pc Pepper And Salt Mill Food Grade And Non-toxic Body Shape: Round Body Material: Wood Size: Diameter: 5 Cm X Height: 20 Cm (minimum) Carved Of Wood With Stainless Steel Grinding Mechanism Color: Natural Screw Cap At The Top Of The Mill To Adjust The Thickness Of Peeper Or Spices Preferably With A Packing Case 88 605.00 53,240.00 36 Pc Piping Bag Type : Piping Bag Body Shape: Triangular Material: Transparent Disposable Plastic For Dispensing Ingredients To Pastries Length: 9 Inches Minimum Width: 3 Inches (minimum) Volume: 500 Ml (approximate) 88 312.00 27,456.00 37 Pc Plate Rack Type: Plate Rack Body Shape: Rectangular Material: 304 Stainless Steel Dimension: Length-475 Mm X Width- 290 Mm X Height- 380 Mm (minimum) 132 1,760.00 232,320.00 38 Pc Preparation Table With Sink Heavy Duty Wire Shelving, 2.6 Mm Diameter (minimum) Body Shape: Rectangular Material: Stainless Steel, 1 Mm Thick (minimum) Dimensions: L-1200 Mm X W - 700 Mm X H - 850 Mm (minimum) Stainless Steel Table Top And Stainless Steel Under Shelf Fully Welded Construction Sink: Left Side Single Bowl Sink With Drainer 4 Inches & Faucet Provision Sink Dimension (l X W X D) 400 Mm X 500 Mmx 25 Mm (minimum) 55 30,000.00 1,650,000.00 39 Pc Pressure Cooker Type: Pressure Cooker Body Shape: Round Material: Polished Aluminum Dimension: Diameter: 32 Cm X Height: 25 Cm (minimum) Capacity: 10 Quarts (11.3 Liters) Side Handles For Secure Carrying Equipped With Safety Opening Mechanism, Spring Safety Valve, Rubber Seal Ring 11 17,309.00 190,399.00 40 Pc Roasting Pan Type: Roasting Pan Body Shape:rectangular Material: Stainless Steel Dimension: Length: 40 Cm X Width-35 Cm X Height -7 1/2cm (minimum) Thickness: 1.5 Mm Thick (minimum) Welded Handles On Both Sides Removable Stainless Steel Wire Rack 44 339.00 14,916.00 41 Pc Scissor, Kitchen Dishwasher Safe Scissor, Kitchen Cookery Nc Ii Type:kitchen Scissor Body Shape: Ergonomic Blade Material: Stainless Steel, 2 Mm Thick Handle Material Heavy Duty Acrylonitrile Butadiene Styrene (abs) Plastic Overall Length: 20 Cm (minimum ) Width: 7.5 Cm (minimum) 88 219.00 19,272.00 42 Pc Siever, Small Type: Fine Mesh Siever Body Shape: Round Material: Stainless Steel Diameter: 20 Cm (minimum) Depth: 7 Cm (minimum) Twin Wire Handle: Length 20 Cm X 5 Mm Diameter (minimum) Fine Mesh: 0.7 Mm (1/32 Inch) (minimum) Preferably With A Packing Case 88 328.00 28,864.00 43 Pc Skimmer, Fine Type: Medium Fine Mesh Skimmer Body Shape: Round Material: Stainless Steel, Polished Overall Length: 34 Cm (minimum) Skimmer Head: Diameter -10 Cm X Depth- 4 Cm (minimum) Diameter Of Holes: 2 Mm (approx.) Handle: Length- 12 Cm X Diameter- 2 Cm (minimum) Handle Has Hole For Hanging Preferably With A Packing Case 88 129.00 11,352.00 44 Pc Skimmer, Spider Type: Skimmer, Spider Body Shape: Round Material: Stainless Steel, Polished Overall Length: 35 Cm (minimum) Skimmer Head Diameter: 15 Cm X Depth 4 Cm (minimum) Handle Length: 12 Cm X 2 Cm Diameter (minimum) Preferably With A Packing Case Dishwasher Safe 88 105.00 9,240.00 45 Pc Soup Cup Rack Type: Soup Cup Rack Body Shape: Square Material: Polypropylene Plastic Dimension: Length: 50 Cm X Width: 50 Cm X Height: 10 Cm (minimum) Compartment Length: 11 Cm Compartment Width: 11 Cm Compartment /inside Height: 6.7 Cm No. Of Compartment: 16 Compartments 132 360.00 47,520.00 46 Pc Soup Ladle, 12oz Type: Soup Ladle Body Shape: Round Material: Stainless Steel Thickness: 1 Mm Thick (minimum) Handle Length: 34 Cm (minimum) Capacity: 12 Oz. (341 Ml) Ladle Type: Round Bottom Hooked Handle Design Allows It To Easily Sit On The Edge Of Pots. Preferably With A Packing Case Dishwasher Safe 22 347.00 7,634.00 47 Pc Soup Ladle, 3 Oz Type: Soup Ladle Body Shape: Round Material: Stainless Steel Thickness: 1 Mm Thick (minimum) Handle Length: 28 Cm (minimum) Capacity: 3 Oz. (85 Ml) Ladle Type: Round Bottom Hooked Handle Design Allows It To Easily Sit On The Edge Of Pots. Preferably With A Packing Case Dishwasher Safe Must Be Branded 88 198.00 17,424.00 48 Pc Soup Ladle, 6 Oz Type: Soup Ladle Body Shape: Round Material: Stainless Steel Thickness: 1 Mm Thick (minimum) Handle Length: 30 Cm (minimum) Capacity: 6 Oz. (170 Ml) Ladle Type: Round Bottom Hooked Handle Design Allows It To Easily Sit On The Edge Of Pots. Preferably With A Packing Case Dishwasher Safe 88 209.00 18,392.00 49 Pc Soup Ladle, 8 Oz Type: Soup Ladle Body Shape: Round Material: Stainless Steel Thickness: 1 Mm Thick (minimum) Handle Length: 30 Cm (minimum) Capacity: 8 Oz. (236 Ml) Ladle Type: Round Bottom Hooked Handle Design Allows It To Easily Sit On The Edge Of Pots. Preferably With A Packing Case 33 135.00 4,455.00 50 Pc Spatula Type: Offset Spatula Body Shape: Flat Blade Material: Stainless Steel 316 Handle Material: Hardwood (smooth Finish) With Rivets Blade Dimension: Length= 7 .5 Inches X Width-1.5 Inches (minimum) Thickness Of Blade: 1.7 Mm Thick (minimum) Total Length = 12 To 14 Inches Preferably With A Packing Case Dishwasher Safe Must Be Branded. 88 249.00 21,912.00 51 Pc Spoon, Kitchen Type: Kitchen Spoon Body Shape: Oval Material: Stainless Steel, 1.5 Mm Thick Overall Length: 30.5 Cm X Width-7.5 Cm (minimum) Spoon Head Dimension (l X W) 9 Cm X 7.5 Cm (minimum) Handle: Abs Plastic Spoon Head: Oval Type Preferably With A Packing Case Heat Resistant Up To 220 ° C Dishwasher Safe Must Be Branded. 88 109.00 9,592.00 52 Pc Spoon, Kitchen (slotted) Type: Kitchen Spoon Slotted Body Shape: Oval With Slot Material: Stainless Steel, 1.5 Mm Thick Overall Length: 30.5 Cm X Width-7.5 Cm (minimum) Spoon Head Dimension (l X W) 9 Cm X 7.5 Cm (minimum) Handle: Abs Plastic Spoon Head: Oval Type With Slot At Least 6 Rectangular Slots Preferably With A Packing Case Heat Resistant Up To 220 ° C Dishwasher Safe 88 236.00 20,768.00 53 Pc Spoon, Measuring Must Be Branded. Spoon, Measuringcookery Nc Ii Type: Measuring Spoon Body Shape: Bowl In Shape Material: Stainless Steel, 0.7 Mm Thick (minimum) The Set Consists Of The Following Sizes: 1 Pc - 1 Tbsp. (15 Ml) 1 Pc - 1/2 Tbsp. ( 7.5 Ml) 1 Pc - 1 Tsp. (5 Ml) 1 Pc - 1/2 Tsp. (2.5 Ml) 88 198.00 17,424.00 54 Pc Spoon, Parisienne Type: Parisiennes Spoon Body Shape: Round Double Headed Parisiennes Scoop Bar Tool Material: Stainless Steel, Polished Overall Length: 240 Mm (minimum) Scoop Diameter: 30 Mm And 24mm (minimum) With Plastic Handle (polypropylene), Size: 130 Mm X Width-20 Mm (minimum) Draining Small Hole In The Scoop 88 281.00 24,728.00 55 Pc Spoon, Serving Type: Serving Spoon Body Shape: Oval Materials: Stainless Steel Dimension: Length: 23 Cm X Width: 5 Cm (minimum) Scoop Dimension (l X W X D): 7 Cm X 5 Cm X 0.9 Cm (minimum) Spoon Thickness: 1.6 Mm (minimum) Preferably With A Packing Case Dishwasher Safe Must Be Branded. 264 223.00 58,872.00 56 Pc Spoon, Wooden Type: Wooden Spoon Body Shape: Oval Material: Hardwood Dimensions: Length- 10 Inches X Width- 2 Inches (minimum) Bowl Dimension: Length -3 Inches X Width 2 Inches X Depth -3/4 Inches (minimum) Total Length: 10 Inches (minimum) Preferably With A Packing Case Smooth Surface Finished And No Sharp Edges 88 150.00 13,200.00 57 Pc Stock Pot, Large Type: Stock Pot, Large Body Shape: Round Material: Stainless Steel, 0.8 Mm Thick (minimum) Top Diameter: 30 Cm (minimum) Height: 31 Cm (minimum) Capacity: 20 Quarts (22.7 Liters) Oven Safe To 350⁰f And Dishwasher Safe. With Aluminum Disc Layer In Bottom For Even Heat (5 Mm Aluminum) 22 7,800.00 171,600.00 58 Pc Strainer Chinois, Small Strainer Chinois, Small Body Shape: Conical Material: Stainless Steel Strainer Diameter: 14 Cm (minimum) Strainer Depth: 13 Cm (minimum) Handle Length: 15 Cm (minimum) With 1 Mm (approx.) Fine Mesh Handle Has Provision For Hanging Preferably With A Packing Case Dishwasher Safe Must Be Branded 33 667.00 22,011.00 59 Pc Strainer Chinois, Small Strainer Chinois, Small Body Shape: Conical Material: Stainless Steel Strainer Diameter: 14 Cm (minimum) Strainer Depth: 13 Cm (minimum) Handle Length: 15 Cm (minimum) With 1 Mm (approx.) Fine Mesh Ha 22 1073 23,606.00 60 Pc Strainer Medium, Fine Type: Strainer, Medium Fine Body Shape: Round Material: Stainless Steel Strainer Diameter: 20 Cm (minimum) Strainer Depth: 7 Cm (minimum) Handle Length: 18 Cm (minimum) With 2 Mm. (approx.) Fine Mesh Strainer’s Two Layers Of Tightly Woven Mesh Catches Handle Has Provision For Hanging Preferably With A Packing Case Dishwasher Safe Must Be Branded. 88 410.00 36,080.00 61 Pc Strainer Small, Fine Type: Strainer, Small Fine Body Shape: Round Material: Stainless Steel Strainer Diameter: 13 Cm (minimum) Strainer Depth: 5 Cm (minimum) Handle Length: 13 Cm (minimum) With 1 Mm. (approx.) Fine Mesh Handle Has Provision For Hanging Preferably With A Packing Case Dishwasher Safe Must Be Branded. 88 253.00 22,264.00 62 Pc Tenderizer, Medium Type: Tenderizer Body Shape: Ergonomic Material: Cast Aluminum Overall Length: 26 Cm (minimum) Dual-sided Hammer, Square Head: 6 Cm X 6 Cm (minimum) Ridged Surface With Rows Of Dull, Pyramid-shaped Spikes Weight: 250 Grams To 500 Grams Preferably With A Packing Case Dishwasher Safe Must Be Branded 88 550.00 48,400.00 63 Pc Thermometer, Pocket/pin Type: Tenderizer Body Shape: Ergonomic Material: Cast Aluminum Overall Length: 26 Cm (minimum) Dual-sided Hammer, Square Head: 6 Cm X 6 Cm (minimum) Ridged Surface With Rows Of Dull, Pyramid-shaped Spikes Weight: 250 Grams To 500 Grams Preferably With A Packing Case Dishwasher Safe Must Be Branded 33 236.00 7,788.00 64 Pc Tong, 12 Inches Type: Tong , 12 Inches Body Shape: Standard Material: Stainless Steel Size: 12 Inches Stainless-steel Arms With Soft, Comfortable Grips Nylon Heads Safe For Nonstick Cookware Heat-resistant Up To 400 Degrees Fahrenheit Tongs Lock Closed For Storage Preferably With A Packing Case Food Grade And Dishwasher-safe Must Be Branded 88 319.00 28,072.00 65 Pc Tong, 8 Inches Type: Tong, 8 Inches Body Shape: Standard Material: Stainless Steel Size: 8 Inches Stainless-steel Arms With Soft, Comfortable Grips Nylon Heads Safe For Nonstick Cookware Heat-resistant Up To 400 Degrees Fahrenheit Tongs Lock Closed For Storage Preferably With A Packing Case Food Grade And Dishwasher-safe 110 289.00 31,790.00 66 Pc Tray, Baking, Small Type: Baking Tray Body Shape: Rectangular Material: Stainless Steel Dimension: 20 Cm X 30 Cm X 3.7 Cm (minimum) Body Thickness: 0.7- 1.0 Mm Preferably With Packing Case Dishwasher Safe Must Be Branded. 88 897.00 78,936.00 67 Pc Tray, Utility Type: Utility Tray Body Shape: Rectangular Material: Stainless Steel Dimension: Length- 48 Cm X Width-32 Cm X Height-2.5 Cm (minimum) Reinforced Edges Finish: Polished Preferably With A Packing Case Washable And Oven Safe 132 536.00 70,752.00 68 Pc Turner 3"x6" Type: Slotted Turner, 3" X 6" Body Shape: Straight Material: Stainless Steel Blade Size (lx W): 6 Inches X 3 Inches (minimum) Handle Length: 5 Inches (minimum) Overall Length: 13 Inches (minimum) Solid Turner With Straight Slotted Blade Wooden Handle With Triple Rivets Preferably With A Packing Case Dishwasher Safe Must Be Branded 88 299.00 26,312.00 69 Pc Utility Cart Type: Utility Cart Body Shape: Rectangular Material: Plastic, Polypropylene(pp) Dimension: (l X W X H) 84 Cm X 43 Cm X 95 Cm (minimum) Capacity: 330 Lbs (150 Kg) Loads (minimum) Three (3) Shelving With At Least 25 Cm Distance Between Shelves Tub Shelf Measure (l X W X D) 84 Cm X 43 Cm X 7 Cm (minimum) With Four (4) Swivel Caster, 10 Cm Diameter, Two Which Have Locking Brakes Preferably With A Packing Case Easy Grip Handles On Each End Of Cart 11 5,564.00 61,204.00 70 Pc Weighing Scale, 1kg, Digital Type: Digital Weighing Scale Body Shape: Rectangular Materials: Engineering Plastic And Stainless Steel Weighing Plate Capacity: 1 Kg Accuracy: 1 Gram Back Light Lcd Display With 15 Mm Minimum High Digits Weighing Units: Gram, Ounce, Pound Size: (l X W X H Mm ) 163 Mm X 245 Mm X 79 Mmm (minimum) 44 1,584.00 69,696.00 71 Pc Wighing Scale, 5kg Type: Mechanical Weighing Scale Body Type: Circular Bowl Material: Stainless Steel Bowl And Metal Body (coated) Mechanism Type: Spring Lever Capacity: 5 Kg /11 Lb. Sensitivity/graduated By 10 Gm Measurement Units: Gram/kilogram Manual Setting On Zero, Must Be Accurate And Durable Calibrate The Scale Using The Adjustment Knob Preferably With A Packing Case Delivery Must Include Instruction Manual Written In Good English With Service Centers Located In The Major Cities In The Philippines Warranty Period Of 1 Year (parts And Service) Must Be Branded 22 2,329.00 51,238.00 72 Pc Wire Skimmer, Small Type: Skimmer, Wire Mesh Body Shape: Round Material: Stainless Steel, Polished Overall Length: 40 Cm (minimum) Skimmer Head Diameter: 12 Cm (minimum) Diameter Of Holes: 2 Mm (approx.) Handle Has Hole For Hanging Preferably With A Packing Case Dishwashing Safe Must Be Branded. 88 399.00 35,112.00 73 Pc Wire Whisk, Heavy Duty Type: Wire Whisk, Heavy Duty Body Shape: Ballon Material: Heavy Duty Stainless Steel Dimensions (l X W): 31.8 Cm X 7.6 Cm (minimum) Handle Length: 12 Cm (minimum) With Hanging Loop No. Of Wires: 8 Wires Wire Diameter: 2 Mm (minimum) Preferably With A Packing Case Dishwasher Safe Must Be Branded. 22 440.00 9,680.00 74 Pc Wire Whisk, Medium Type Wire Whisk, Medium Body Shape: Ballon Material: Stainless Steel Wire Whisk Medium Dimensions (l X W): 25.4 Cm X 7 Cm (minimum) Handle Length: 10 Cm (minimum) With Hanging Loop No. Of Wires: 6 Wires Wire Diameter: 1.8 Mm (minimum) Preferably With A Packing Case Dishwasher Safe Must Be Branded. 88 454.75 40,018.00 75 Pc Wire Whisk, Small Type Wire Whisk, Medium Body Shape: Ballon Material: Stainless Steel Wire Whisk Medium Dimensions (l X W): 25.4 Cm X 7 Cm (minimum) Handle Length: 10 Cm (minimum) With Hanging Loop No. Of Wires: 6 Wires Wire Diameter: 1.8 Mm (minimum) Preferably With A Packing Case Dishwasher Safe Must Be Branded. 88 378.00 33,264.00 76 Pc Wok, Medium Type: Wok, Medium Body Shape:round Material: Carbon Steel Thickness: 1.8 Mm Thick (minimum) Dimensions (dia. X H): 45 Cm X 14 Cm (minimum) Handle Material: Steel Riveted Convenient Both Side Handle 10 Cm (minimum) With Flat Bottom Preferably With A Packing Case Dishwashing Safe Must Be Branded 11 4,099.00 45,089.00 77 Pc Wok, Small Type: Wok, Small Body Shape: Round Material: Carbon Steel Thickness: 1.5 Mm Thick (minimum) Dimensions (dia. X H): 36 Cm X 10 Cm (minimum) Handle Material: Steel Riveted Convenient Both Side Handle 8 Cm (minimum) With Flat Bottom Preferably With A Packing Case Dishwashing Safe Must Be Branded 44 3,194.00 140,536.00 78 Pc Working Table Type: Working Table, Stainless Steel Body Shape: Rectangular Material: 304 Stainless Steel, 1.29 Mm Thick (gauge 16) Minimum Length: 1220 Mm (minimum) Width: 700 Mm (minimum) Height: 850 Mm (minimum) Tubular Stainless Steel Legs, 38mm (minimum) With 4 Adjustable Bullet Feet Fully Welded Construction Thickness:gauge 16 (1.29 Mm Thick) Minimum Stainless Steel Table Top With Stainless Steel Undershelf Distance Between Table Top And Undershelf Is 650 Mm (minimum) Preferably With A Packing Case Or Crate No Sharp Edges And Rough Surfaces Must Be Branded. 22 41,720.00 917,840.00 79 Pc Zester Type: Cheese Zester Body Shape: Standard Material: Stainless Steel Grating Surface Dimensions (l X W): 20.3 Cm X 4 Cm (minimum) Overall Length: 32.5 Cm (minimum) Handle Material: Plastic (polypropylene) Ergonomic Handle Preferably With A Packing Case Dishwasher Safe The Plastic Material Used Must Be Non-toxic Must Be Branded. 88 399.00 35,112.00 Total 7,732,802.00 Lot B: Bread And Pastry Production 1 Pc Air Compressor With Airbrush Cake Decorating Set Ultra-compact Airbrush Compressor Designed For Quiet Operation Oil-less, Maintenance-free Design (safe For Food Applications) Delivers Up To 25 Psi (0.4 Cfm) Of Consistent Airflow Uses Standard 1/8″ Bsp Male Outlet To Connect To The Air Hose Operates On 12v Dc Power (ac Adapter Provided) Designed For Intermittent Use (30 Minutes Of Operation Followed By A 15-minute Cooldown) Includes A Nylon Air Hose With Standard 1/8″ Bsp Fittings 8 24600 196,800.00 2 Pc Beater Type: Beater Main Material: Plastic + Stainless Steel Color: White Wide Operating Voltage Range: 0-250v Rated Voltage: 220v Rated Frequency: 50hz Speed Selection: 0-7 Gear Rated Power: 100w Hand Mixer Size: 180 * 70 * 130mm/7.09 * 2.76 * 5.12in 48 960 46,080.00 3 Pc Board, Chopping, 6 Color Type: Cutting Board Body Shape: Rectangular Material: Plastic (polypropylene), Food Grade Board Size: Length: 15 Inches (minimum) Width: 12 Inches (minimum) Thickness: 0.5 Inch (minimum) With Hole For Storage Purposes Preferably With Packing Case Food Grade And Dishwasher Safe 48 659 31,632.00 4 Pc Boiler, Double Material: Stainless Steel Thickness: 1/16 Inch (1.5 Mm) (minimum) Lid Material: Glass Rivetedhandle On Both Side Diameter: 9 1/2 Inches (minimum) Total Height: 9.4 Inches (minimum) Inset Bottom Diameter: 9 Inches (minimum) Inset Top Diameter: 9 Inches (minimum) Capacity: 2 Liters (minimum) 8 8700 69,600.00 5 Pc Bowl, Mixing (6 Pcs/set) Material: Stainless Steel / Food-grade Plastic Sizes: Assorted (small To Large) 96 911 87,456.00 6 Pc Cake Pans, Round #4,#6, #8, #10, #12, #14, #16 Material: Aluminum Or Non-stick Carbon Steel Sizes: #4: 4-inch Diameter #6: 6-inch Diameter #8: 8-inch Diameter #10: 10-inch Diameter #12: 12-inch Diameter #14: 14-inch Diameter #16: 16-inch Diameter 48 937 44,976.00 7 Pc Cake Stand, With Tier Type: Cake Stand With Tier, Food Grade Body Shape: Circular With 3 Tier Material: Hard Plastic, Polypropylene, 4 Mm Thick The Tier Consists Of The Following Sizes: Tier 1: 18 Cm Diameter (minimum) Tier 2: 25 Cm Diameter (minimum) Tier 3 : 30 Cm Diameter (minimum) Column Diameter: 20 To 30 Mm (solid) Distance Between Tiers: 15 Cm Over-all Length: 30 Cm (minimum) Assembled Column Is Used For Maximum Strength And Stability Of The Stand Must Be Packed In Set Smooth And No Sharp Edges 48 5589 268,272.00 8 Pc Cake Turn Table Type: Turn Table Body Shape : Circular Material: Cast Aluminum Plate.and Cast Iron Base Upper Plate: 30 Cm Diameter (minimum) And 1.4 Cm Thickness (minimum) Base Dimensions: 18 Cm (minimum); 1.4 Cm Thickness (minimum) Total Height: 10 Cm To 15 Cm Turntable With Ball Bearing To Turn Easier Preferably Packed In Any Kind Of Packaging Comes With No Sharp Edges To Rotate Smoothly In 360 Degrees Clockwise Or Counter Clockwise 24 3500 84,000.00 9 Pc Coupler Type: Foood Grade Body Shape: Tubular Material: Hard Plastic, Polypropylene, Any Bright Color Height: 3cm (minimum) Top Diameter: 1.27 Cm (minimum) Bottom Diameter: 2.54 Cm (minimum) Preferably With Storage Case The Materials Used Must Be Non-toxic And Dishwasher Safe 104 250 26,000.00 10 Pc Cup, Measuring (for Solid) Type: Measuring Cup Set Body Shape: Round Material: Stainless Steel, 0.7 Mm Thick (minimum) Each Set Contains The Following: 1 Pc - 1 Cup (237 Ml) 1 Pc - 1/2 Cup (118 Ml) 1 Pc - 1/3 Cup (79 Ml) 1 Pc - 1/4 Cup (59 Ml) Handle Dimension: Length-12 Cm X Width-1 Cm (minimum) Measuring Capacity Engraved On The Handle Strip Handles Have Provision For Hanging Preferably With Packing Case Smooth Surfaces And Dishwasher Safe 96 300 28,800.00 11 Pc Cup, Measuring, 250 Ml For Liquid Type: Glass V-shaped Nozzle High Quality 3.3 Borosilicate0ml (2oz)high Borosilicate Glass Measuring Cup-v-shaped Spout 120ml (4oz)high Borosilicate Glass Measuring Cup-v-shaped Spout 250ml (8oz)high Borosilicate Glass Measuring Cup-v-shaped Spout 96 289 27,744.00 12 Pc Cup, Measuring, 500ml For Liquid Material: Food-grade Plastic Or Stainless Steel Capacity: 500ml (16.9 Oz) Graduation Markings: Clearly Marked In Milliliters (ml) And Ounces (oz) For Precise Measurement Handle: Ergonomic, Heat-resistant Handle For Easy Pouring 96 394 37,824.00 13 Pc Cutter, Dough Type: Scrapper Body Shape: Straight Blade Material: Stainless Steel Straight Blade With Stainless Steel Handle Blade Dimension: Lenght : 15 Cm X Width: 11 Cm X Thickness: 1.2 Mm(minimum) Handle Dimension: Length: 15 Cm X Diameter: 3 Cm (minimum) Preferably With Packing Case Food Grade And Dishwasher Safe Design Allows Item To Be Hung For Storage 8 214 1,712.00 14 Pc Cutter, Pie Type: Cutter Product Dimensions 8.8"l X 0.8"w Blade Material Stainless Steel Handle Material Plastic Or Stainless Steel Or Silicone Or Bamboo 48 473 22,704.00 15 Pc Flour Sifter, Hand Cranked Type: Hand Cranked Body Shape: Round Shape Material: Stainless Steel Dimension: Diameter: 133.3 Mm ( Minimum) X Height: 165 Mm (minimum) Thickness: 0.79 Mm (minimum) (body) And Constructed With Stainless Steel Wire Mesh # 30 Bottom Volume Markings Should Be Seen Inside And Outside Of The Sifter Capacity: 5 Cups (1.18 Liter) Spring Action Squeeze Handle Stainless Steel Preferably With A Packing Case Dishwasher Safe 24 323 7,752.00 16 Pc Grater Type: Four Sided Box Grater Body Shape: Box In Shape Material: Stainless Steel Blade And Plastic (polypropylene Handle) Grater Dimensions: Height- 25 Cm X Width-13 Cm X Depth-10 Cm (minimum) Side 1: Large-hole Shredder With 6 Mm Hole Side 2: Slicer Side 3: Small-hole Shredder With 3 Mm Hole Side 4: Grater With Strips About 1.27 Cm To 2.54 Cm Length Preferably With Packing Case Food Grade & Dishwashing Safe 48 518 24,864.00 17 Pc Knife, Kitchen Material: Stainless Steel Blade With Non-slip Handle Blade Length: 8-10 Inches Purpose: General Food Preparation 48 519 24,912.00 18 Pc Knife, Pallet Material: Stainless Steel Blade With Plastic/wood Handle Blade Length: 8-12 Inches Type: Offset Or Straight Blade Purpose: Spreading, Smoothing, And Decorating Cakes 48 286 13,728.00 19 Pc Ladle , 3 0z Material: Stainless Steel With Heat-resistant Handle Capacity: 3 Oz (90 Ml) Purpose: Portioning Liquid Ingredients Such As Batters, Sauces, And Glazes 48 396 19,008.00 20 Pc Loaf Pan Big Material: Aluminum Or Non-stick Carbon Steel Sizes: Big: 9 X 5 X 3 Inches 48 598 28,704.00 21 Pc Loaf Pan, Medium Material: Aluminum Or Non-stick Carbon Steel Medium: 8 X 4 X 3 Inches 48 478.00 22,944.00 22 Pc Loaf Pan, Small Material: Aluminum Or Non-stick Carbon Steel Small: 7 X 3 X 2.5 Inches 48 325.00 15,600.00 23 Pc Muffin Pan, Big Material: Non-stick Carbon Steel Or Aluminum Sizes & Capacity: Big: 6-cup Jumbo Muffin Size (3.5-inch Diameter Per Cup) 48 649.00 31,152.00 24 Pc Muffin Pan, Medium Material: Non-stick Carbon Steel Or Aluminum Sizes & Capacity: Medium: 12-cup Standard Muffin Size (2.75-inch Diameter Per Cup) 48 814.00 39,072.00 25 Pc Muffin Pan, Small Material: Non-stick Carbon Steel Or Aluminum Sizes & Capacity: Small: 24-cup Mini Muffin Size (1.5-inch Diameter Per Cup) 48 1,429.00 68,592.00 26 Pc Pie Pan , 10 Inches Diameter Material: Aluminum Or Non-stick Carbon Steel Diameter: 10 Inches 48 995.00 47,760.00 27 Pc Pie Pan, # 6, #8, #10 Type: Pie Pan Depth: ~1 To 1.5 Inches Material Options: Aluminum, Non-stick Coated Steel, Glass, Ceramic, Depth: ~1.25 To 1.75 Inches Material Options: Aluminum, Stainless Steel, Glass, Ceramic, Depth: ~1.5 To 2 Inches Material Options: Heavy-duty Aluminum, Glass, Ceramic 48 850.00 40,800.00 28 Pc Pillars, Cake Material: Food-grade Plastic Or Acrylic Height: 3-10 Inches (various Sizes) Type: Round 48 790.00 37,920.00 29 Pc Piping Bag Type : Piping Bag Body Shape: Triangular Material: Transparent Disposable Plastic For Dispensing Ingredients To Pastries Length: 9 Inches Minimum Width: 3 Inches (minimum) Volume: 500 Ml (approximate) 200 312.00 62,400.00 30 Pc Rectangular Pan, 1 X 8 Material: Aluminum Or Non-stick Carbon Steel Sizes: #6: 6-inch Diameter (small Pies) #8: 8-inch Diameter (medium Pies) #10: 10-inch Diameter (large Pies) 32 594.00 19,008.00 31 Pc Rolling Pins Classic Wooden (rod Or Handle Type) Standard: 10-18 Inches Mini: 7-10 Inches (for Smaller Pastries) Large: 18+ Inches (for Heavy-duty Baking) 48 425.00 20,400.00 32 Pc Rubber Scraper Type: Flat Scraper Small (6-8 Inches) – Ideal For Small Bowls And Precise Scraping. Medium (9-12 Inches) – General Baking And Mixing. Large (12+ Inches) – Good For Big Batches And Cooking. 48 525.00 25,200.00 33 Pc Sauce Pan Type: Sauce Pan Body Shape: Round Material: Stainless Steel, 0.8 Mm Thick (minimum) Top Diameter: 30 Cm (minimum) Height: 31 Cm (minimum) Capacity: 20 Quarts (22.7 Liters) Oven Safe To 350⁰f And Dishwasher Safe. With Aluminum Disc Layer In Bottom For Even Heat (5 Mm Aluminum 48 3,590.00 172,320.00 34 Pc Sheet Pan Oven Safe Up To 450 Degrees F; Dishwasher-safe For Easy Cleaning 17.7 X 12.4 X 1.1 Inches (lxwxh, Baking Sheet); 16.7 X 11.7 Inches (lxw, Cooling Rack) 48 721.00 34,608.00 35 Pc Spoon, Measuring Must Be Branded. Spoon, Measuringcookery Nc Ii Type: Measuring Spoon Body Shape: Bowl In Shape Material: Stainless Steel, 0.7 Mm Thick (minimum) The Set Consists Of The Following Sizes: 1 Pc - 1 Tbsp. (15 Ml) 1 Pc - 1/2 Tbsp. ( 7.5 Ml) 1 Pc - 1 Tsp. (5 Ml) 1 Pc - 1/2 Tsp. (2.5 Ml) 200 508.00 101,600.00 36 Pc Spoon, Wooden Type: Wooden Spoon Body Shape: Oval Material: Hardwood Dimensions: Length- 10 Inches X Width- 2 Inches (minimum) Bowl Dimension: Length -3 Inches X Width 2 Inches X Depth -3/4 Inches (minimum) Total Length: 10 Inches (minimum) Preferably With A Packing Case Smooth Surface Finished And No Sharp Edges 48 190.00 9,120.00 37 Pc Strainer Type: Strainer Body Shape: Round Material: Stainless Steel Strainer Diameter: 20 Cm (minimum) Strainer Depth: 7 Cm (minimum) Handle Length: 18 Cm (minimum) With 2 Mm. (approx.) Fine Mesh Strainer’s Two Layers Of Tightly Woven Mesh Catches Handle Has Provision For Hanging Preferably With A Packing Case Dishwasher Safe Must Be Branded 48 394.00 18,912.00 38 Pc Tip, Decorating Stainless Steel Color Silver 160 120.00 19,200.00 39 Pc Weighing Scale, 10 Kgs Black And Silver Recommended Uses For Product Kitchen Special Feature Lightweight Display Type Analog 48 2,540.00 121,920.00 40 Pc Weighing Scale,5 Kgs, Digital Type: Mechanical Weighing Scale Body Type: Circular Bowl Material: Stainless Steel Bowl And Metal Body (coated) Mechanism Type: Spring Lever Capacity: 5 Kg /11 Lb. Sensitivity/graduated By 10 Gm Measurement Units: Gram/kilogram Manual Setting On Zero, Must Be Accurate And Durable Calibrate The Scale Using The Adjustment Knob Preferably With A Packing Case Delivery Must Include Instruction Manual Written In Good English With Service Centers Located In The Major Cities In The Philippines Warranty Period Of 1 Year (parts And Service) Must Be Branded 48 1,198.00 57,504.00 41 Pc Wire Whisk, Medium Type Wire Whisk, Medium Body Shape: Ballon Material: Stainless Steel Wire Whisk Medium Dimensions (l X W): 25.4 Cm X 7 Cm (minimum) Handle Length: 10 Cm (minimum) With Hanging Loop No. Of Wires: 6 Wires Wire Diameter: 1.8 Mm (minimum) Preferably With A Packing Case Dishwasher Safe Must Be Branded. 48 421.00 20,208.00 Total 2,078,808.00 Lot C: Computer Systems Servicing 1 Pcs Allen Wrench 1. Material: Chrome Vanadium Steel, Hrc 38 To 60; 2. Set Of 10 Pieces: 1.5 Mm, 2 Mm, 2.5 Mm, 3 Mm, 4 Mm, 5 Mm, 5.5 Mm, 6 Mm, 8 Mm, 10 Mm; 3. With Holder/ring To Keep The Set Intact; 4. Label Of Sizes Engraved In Each Allen Wrench; 5. Smooth Surfaces And No Sharp Edges6. Plastic Pack By Set 10 ₱962.00 ₱9,620.00 2 Pcs Anti-static Device (anti-static Wrist Strap) Consists Of: A) Adjustable And Elastic Wristband With Integrated 1 Mega Ohm Resistor, B) Banana Plug With Alligator Clip For Connecting To Ground (or Equivalent), C) At Least 59" Long Coiled Cord; D) Non Toxic Materiale) Carton Box Or Plastic Pouch Packaging 10 ₱184.80 ₱1,848.00 3 Pcs Combination Pliers, 8" Type: Combination Pliers; Body Shape: Square Nose Material: Chrome Vanadium/forged Steel Length: 9 Inches (minimum) Insulation Range: 1000 Volts (etched On The Handle) Design: Square Nose With Serrated Jaw Comes With Nickel Plated Finish, Side Cutter And Insulated Handle Must Be Branded (brand Must Etched Either In The Head Or On The Handle) 10 ₱187.00 ₱1,870.00 4 Pcs Crimping Tool (rj 11/45) 1. Ratchet Crimp Tool 2. All-in-one Tool That Can Strip, Cut, And Crimp 3. Lightweight Steel Frame 4. Rj-11/45 Compatible 5. Positions For 8p/8c, 6p/6c And 4c Connectors 6. Lightweight, Compact, And Durable 7. Smooth Surface And No Sharp Edges Except Cutting Edges 8. Carton Box Packaging 30 ₱532.00 ₱15,960.00 5 Pcs Desoldering Pump 1. Material : Plastic Or Aluminum Housing; 2. Replaceable Heat-resistant Plastic Tip; 3. Length : Minimum Of 6 Inches; 4. Effective In Removing Solder; 5. Smooth Surface And No Sharp Edges 6. Carton Or Plastic Packaging 10 ₱75.00 ₱750.00 6 Pcs Electric Drill, Portable Type: Electric Power Material: Hard Plastic Rated Voltage: 220 / 240 Volts, Ac 60 Hz Power In Watts: 550 To 650 Watts Speed: Variable Speed Chuck Capacity: 2 To 13 Mm Power Cord Must Have Flat Blade Attachment Plug (type A Plug) Comes With Hss Drill Bits: 2mm 4pcs. 4 Mm 4pcs. 6 Mm 4pcs. 8 Mm 4pcs. 10 Mm 4pcs. 12 Mm 4pcs. 12.5 Mm 4pcs. Total- (28 Pcs) Masonry Drill Bits; 4 Mm 2pcs. 6 Mm 2pcs.8 Mm 2pcs. 10 Mm 2pcs. 12 Mm 2pcs. Total- (10 Pcs.) With Hammer Function For Concrete Drilling Comes With English User's Manual Includes Of The Following: A. A Diagram Of The Parts With Label; B. Assembly Instructions; C. Operating Procedures; D. Safety Precautions When Using The Equipment; E. Basic Troubleshooting And Maintenance Procedures. Warranty Period Of Parts And Service: 1 Year 1 ₱1,644.00 ₱1,644.00 7 Pcs External Optical Drive 1. Interface: Usb 3.0 Or Better; 2. Compatibility: Windows 2000, Xp, Vista, 7, 8, 10, Apple Mac, Linux Or Better; 3. Read Speed: At Least 8x Dvd, At Least 24x Cd; 4. Write Speed: At Least 4x Dvd, At Least 16x Cd; 5. Package Includes: A) 1 X External Optical Drive, B) 1 X Usb Power Cable, C) 1 X Usb Data Cable, 6. Item Size: 5.4"x 5.51"x0.63"(l X W X H) Approximate 7. Metal Or Hard Plastic Casing 8. Smooth Surface And No Sharp Edges 9. Carton Box Packaging 10. With User's Manual In English Which Includes: A. A Diagram Of The Parts With Their Names, B. Operating Procedures 11. With Service Centers Located In Major Cities In The Philippines. 2 ₱1,700.00 ₱3,400.00 8 Pcs Flash Drive 1. Capacity: 32 Gb ; 2. Connectivity: Usb 3.0, Backward-compatible With Usb 2.0, Plug And Play ; 3. Device/os Compatibility: Windows Vista, Windows 7, 8, 10, Mac Os 10.6+ Or Later Versions; 4. Form: Swivel Type Or With Cover; 5. Dimension: 0.40 X 0.80 X 2.31 In. (10.16 X 20.32 X 58.67 Mm) Approximate 6. Metal Or Hard Plastic Casing 7. Smooth Surface And No Sharp Edges 8. Carton And/or Plastic Packaging 9. User's Guide On Name Of Parts, Connection Guide, Maintenence And Safety Precautions. 30 ₱509.00 ₱15,270.00 9 Pcs Flashlight, Head-mounted 1. Type: Rechargeable, Head Mounted Led Flashlight; 2. Minimum Of 160 Lumens; 3. Beam Distance: Minimum Of 150 Meters; 4. Includes 220 V Ac Charger/power Adaptor (or Equivalent); 5. Charging Time: 3-6 Hours; 6. Provides Up To 30 Hours (minimum) Of Constant Light On A Single Full Charge; 7. Approximate Size: 60x 30mm 8. Smooth Surface And No Sharp Edges 9. Carton Box Or Plastic Pouch Packaging. 10. With User's Manual In English Which Includes: A. A Diagram Of The Parts With Their Names, B. Operating Procedures C. Safety Precautions When Using The Equipment, D. Basic Troubleshooting And Maintenance Procedures 5 ₱480.00 ₱2,400.00 10 Pcs Hub / Switch 1. Standards And Protocols: Ieee 802.3, Ieee802.3u, Ieee802.3x Csma/cd 2. Interface: 8 10/100mbps Ports, Auto-negotiation, Auto-mdi/mdix 3. External Power Supply Adapter: 100-240vac,50/60hz 4. Fanless 5. Data Rates: 10/100mbps At Half Duplex ; 20/200mbps At Full Duplex 6.led Indicator: Power, 1, 2, 3, 4, 5, 6, 7, 8 7.dimensions: 5.3 X 3.1 X 0.9 In. (134.5 X 79 X 22.5mm) (approx.) 8. Transfer Method: Store And Forward 9. Advance Functions: Green Technology, Saving Power Up To 73%; 802.3x Flow Control, Back Pressure; Auto-uplink Every Port 10. Certification: Fcc, Ce, Rohs11. 30 ₱3,030.00 ₱90,900.00 11 Pcs Lan Cable Tester 1 Cable Tester With Led Indication For Rj12, Rj11, Rj45, Cat5e, Cat5, 10/100 Base-t; 2 Main Tester: 1-2-3-4-5-6-7-8-g; 3 Remote Tester: 1-4-3-2-5-6-7-8-g; 4 Power Supply: 9 V Battery (included); 5 Capable Of Testing Crossover, Straight-through, And Rollover Cables; 6 Includes Plastic Case Or Pouch; 7 With User's Manual In English Which Includes: A. A Diagram Of The Parts With Their Names, B. Operating Procedures C. Safety Precautions When Using The Equipment, 5 ₱300.00 ₱1,500.00 12 Pcs Long Nose Pliers, 8" 1 Material: Chrome Vanadium Steel, Hrc 38 To 60; 2 Length: 7 Inches (minimum); 3 Handle Type: Curved Handle With Rubber Cushion For Easy Grip; 4 Jaws Type: Knurled And Long Tempered; 5 Comes With Hardened Cutting Edges And Chrome-nickel Finish. 6. Smooth Surface And No Sharp Edges 7. Carton Or Plastic Packaging 10 ₱665.00 ₱6,650.00 13 Pcs Multimeter, Digital Material: Plastic Casing Main Functions: Auto Range/data Hold/back Light/ Led Lamp/diode Test/triode Test/continuity/ Overload Protection/low Battery Indication/auto Power Off/short-circuit Protection. Display: True Rms, 6000 Counts, 3 5/6 Digits Overload Display: Display Oldc Voltage:600mv/6v/60v/600v(0.5%+3), 1000v (0.5%+3) Ac Voltage:600mv/6v/60v/600v/750v (0.8%+5) Dc Current:600a/6000a/60ma/600ma/10a (1.2%+3) Ac Current:600a/6000a/60ma/600ma/10a (1.5%+3) Resistance:600/6k/60k/600k/(1.0%+3) ,6m/60m (1.5%+3) Capacitance: 10nf/100nf/1000nf/10uf/100uf/1000uf (4.0%+5), 10mf/100mf(5.0%+5) 11 ₱1,700.00 ₱18,700.00 14 Pcs Patch Panel (48 Ports) 1. Network Patch Panel 2. 48 Port Patch Panel 3. Cat6 Cable 4. Material: Abs Plastic 5. Application: Utp(unshielded) 6. Certification: Rohs, Iso, Ce 7. Rj45 Connector: Two Rows (1-24 Ports & 25-48 Ports) 8. Transport Package: 1pcs/box 9. Smooth Surface And No Sharp Edges 20 ₱4,363.00 ₱87,260.00 15 Pcs Pc Video Camera 1) 5.0 Mega Pixel Web Camera, Usb-type; 2) With Microphone For Laptop And Desktop Pc Use; 3) Resolution: At Least 640 X 480; 4) Support Windows Xp/7/8/equivalent Mac Os Or Later Versions; 5) With User's Manual In English Which Includes: A) A Diagram Of The Parts With Their Names, B) Operating Procedures C) Basic Troubleshooting And Maintenance Procedures. 6) Hard Plastic Or Metal Casing 7) Smooth Surface And No Sharp Edges 1 ₱1,389.00 ₱1,389.00 16 Pcs Phillip’s Screwdriver, 8" Insulated 1. Shank Material: Chrome Vanadium Steel, Hrc 38 To 60; 2. Handle Material: Molded Plastic 3. Overall Length: 8 Inches (minimum) 4. Insulation Protection (including Shank): 1000vac/ 1500vdc, Vde Certified (or Its Equivalent) 5.nonslip Handle Design6. Carton Or Plastic Packaging 10 ₱1,842.00 ₱18,420.00 17 Pcs Precision Screwdriver Set 1. Material: Hardened And Tempered Steel. 2. 1 Set Comes With The Following: A) 3 X Phillips Tip No. 00, 0, And 1; B) 6 X Standard Tip No. 1, 1.2, 1.4, 1.8, 2.4, And 3.0; C) 1 X Awl; D) 1 X Magnet; E) Plastic Storage Case; 3. Non Slip Design Handle 5 ₱3,204.00 ₱16,020.00 18 Pcs Soldering Iron, 60w 1. Type: Iron Rod 2. Voltage: 220/240vac, 60hz, Single Phase; 3. Power: 60w (minimum); 4. Body Length: 8.3 Inches (21 Cm) Approximate 5. Cord Length: 1.5 Meters (minimum) 6. Handle: Plastic; (non-slip Handle) 7. With User's Manual Written In English That Contains User's Guide, Operating Procedure, Parts With Description, Safety Procedure, And Maintenance; 8. Interchangeable Copper Tip; 9. Should Have Available Spare Parts Nationwide For A Minimum Period Of 5 Years; 10. Carton And/or Plastic Packaging 10 ₱378.00 ₱3,780.00 19 Pcs Standard Screwdriver (flat), 8” Insulated 1. Shank Material: Chrome Vanadium Steel, Hrc 38 To 60; 2. Handle Material: Molded Plastic 3. Overall Length: 8 Inches (minimum) 4. Insulation Protection (including Shank): 1000v, Vde Certified (or Its Equivalent) 5.nonslip Handle Design 6. Carton Or Plastic Packaging 10 ₱1,011.00 ₱10,110.00 20 Pcs Uninterruptible Power Supply (ups) The Item Shall Have The Following Specifications: 1. Type: Battery (included): Lithium Ion Battery Or Maintenance-free Sealed Lead-acid Battery With Suspended Electrolyte: Leakproof 2. Voltage: Nominal Input Voltage: 230v, 50/60 Hz 3. Output Power Capacity: 600va (minimum) 4. Output Connections:2 Universal Receptacle (minimum) 5. Cord Length: 1 Meter (minimum) 20 ₱2,200.00 ₱44,000.00 21 Pcs Usb External Hd 1) 1tb Portable/external Hard Drive 2) Application: Laptop / Desktop Pc 3) Interface Type: Sataii 4) Installation: Mobile 5) Formatted Capacity: 1000gb (windows Display About 298gb) 6) Size(mm): 14.29 X 80.01 X 17.60 (approx.) 7) Metal Casing 2 ₱3,200.00 ₱6,400.00 22 Pcs Wire Stripper Type: Spring-loaded Self Opening; Body Shape: Long Jaw With Slot Blade Material: Hardened Alloy Steel (sharp Edges To Strip And Cut The Wires) Wires To Be Stripped: 10 Awg To 24 Awg Length: 7 Inches (minimum) Comes With Automatic Self- Adjusting Spring, Crimping Slot, And Hard Plastic Hand 6 ₱1,335.00 ₱8,010.00 23 Pcs Wireless Access Point Type: Wireless Access Point Dual Band Wifi Band / Datatransfer Rate: 867 Mbps At 5 Ghz And 300 Mbps At 2.4 Ghz Band Operating Modes: Access Point (ap), Bridge, Wireless Client, Repeater Interface: One 10/100m Ethernet Port(rj45), Support Passive Poe Power On/off Button And Reset Button Comes With External Power Supply: 5vdc-12vdc / 0.5a-1.0a Dimensions ( L X W X D ): (76-191 ×47-125 ×30-68mm) 32 ₱1,100.00 ₱35,200.00 Total ₱401,101.00 Lot D: Food And Bevarage Services 1 Pc Chair, Dining Type : Dining Side Chair Body Shape: Square Material : Metal (round Or Square) Dimesion: Total Height - 33" X 15" X15" (minimum) Capacity: 150 Kg. Black Colored Powder Coated Frame With Foam On Seat Packed In Carton Box The Item Must Have Good Quality 288 3099 892,512.00 2 Pc Coffee Pot, 2 Pints Type: Manual Drip Body Shape: Round Material : Stainless Steel With Cover Capacity : 2 Pints Outside Diameter : 90 -110 Mm Over-all Height : 200 - 230 Mm Thickness : 0.5 - 1 Mm With Handle And Spout Packed In Carton Box The Item Must Have Good Quality 16 2500 40,000.00 3 Pc Container, Creamer Design: Type: Porcelain With Spout Body Shape: Circular Material: Porcelain Diameter : 50 - 65 Mm Height : 80 - 105 Mm Color : White Appearance : Glossy White Packed In Carton Box The Item Must Have Good Quality 40 537 21,480.00 4 Pc Cups And Saucers 5-6 Oz 1. Material : Porcelain 2. Capacity : 5 Oz./140 Ml 3. Heatproof Up To 300 Deg. C 4. Color : White 5. The Item Must Be Of Good Quality 6. Packed In Carton Box 192 315 60,480.00 5 Pc Fork, Cocktail 1. Material/appearance: Stainless Steel, Highly Polished, W/ Plain Design 2. Type : Rounded Tip Handle 3. Over-all Length : 110 - 165 Mm 4. Width : 20 - 30 Mm (minimum) 5. Handle Thickness : 2 Mm To 4 Mm 6. Handle Length : 75 - 90 Mm 7. Small, 8. Color : Silver 9. The Item Must Be Branded And Have Good Quality. 192 279 53,568.00 6 Pc Fork, Dessert Type : Dessert Fork Body Shape: Fork Shape, Round Tip Material/appearance : Stainless Steel, Highly Polished,with Plain Design, Rounded Tip Handle Length : 150 Mm - 175 Mmwidth : 20 - 30 Mmhandle Thickness : 1.5 Mm - 3 Mm Number Of Tines : 4 Handle : 130 Mm (minimum) Color : Silver Packed In Plastic Pouch The Item Must Be Of Good Quality 192 271 52,032.00 7 Pc Fork, Dinner Type: Dinner Fork Body Shape: Fork Shape Material / Appearance : Stainless Steel, Highly Polished, With 4 Tines Over - All Length : 120 - 175 Mm Thickness Of Handle : 2 - 3 Mm Color : Silver Packed In Plastic Pouch The Item Must Be Of Good Quality 192 235 45,120.00 8 Pc Fork, Fish Type : Fish Fork Body Shape: Fork Shape With Round Tip Material / Appearance : Stainless Steel, Highly Polished, With Plain Design Over-all Length : 180 - 215 Mm Fork Width : 1.5 Mm - 3 Mm Fork Thickness : 1 Mm - 2 Mm Number Of Tines : 4 Length Handle : 120 - 130 Mmhandle Thickness : 2 Mm - 3 Mm Color : Silver Packed In Plastic Pouch The Item Must Be Of Good Quality 192 223 42,816.00 9 Pc Fork, Oyster Type: Oyster Fork Body Shape: Fork Shape Material: Stainless Steel, With High Polish Appearance, And With Plain Design Length: 90 - 120 Mm Thickness: 1 Mm - 3 Mm Silver Color With Three Short Wide Curved Tines Packed In Plastic Pouch The Item Must Be Of Good Quality 192 223 42,816.00 10 Pc Glass, Champagne Flute Type : Flute Glass Body Shape: Round Material: Clear Crystal Glass Dimension : Height: 20 -24 Cm, Top Diameter: 50 -70 Mm, Bottom Diameter: 60 - 80 Mm Capacity: 250 Ml. (minimum) Thickness: 1.5 - 3 Mm Packed In Carton Box The Item Must Have Good Quality 192 264 50,688.00 11 Pc Glass, Collins Type: Tumbler Body Shape: Round Material : Clear Glass Capacity : 10 Oz To 14 Oz Thickness : 1.5 -3 Mm (minimum) Packed In Carton Box The Item Must Have Good Quality 192 299 57,408.00 12 Pc Glass, Juice / Hi- Ball 1. Material : Clear Glass 2. Type : Hi-ball 3. Height : 140 - 160 Mm 4. Bottom Diameter : 50 -70 Mm 5. Top Diameter : 50 - 70 Mm 6. Thickness : 2 - 4 (minimum) 7. Capacity : 8 Oz. To 10 Oz. 8. Diswasher Safe 9. The Item Must Be Branded And Good Quality 10. Packed In Carton Box 192 309 59,328.00 13 Pc Glass, Pilsner (ice Tea Glass) Type: Flaired Rim Body Shape: Round Slender Material: Clear Glass Capacity: 20 Oz. To 23 Oz. Over-all Length: 22 -25 Cm Thickness Of Glass : 1 -3 Mm With Flaired Rim And Slender Shape Packed In Carton Box The Item Must Have Good Quality 192 309 59,328.00 14 Pc Glass, Red Wine Type: Royalty Body Shape: Balloon Shaped Bowl Material: Crystal Clear Glass Rim Diameter : 55 - 60 Mm Thickness : 1.5 Mm - 3 Mm Over - All Length : 200 -220 Mm Capacity : 250 -300 Ml Stem Diameter : 6 - 8 Mm Stem Length : 85 - 90 Mm Base Diameter : 75 - 85 Mm Base Thickness : 2 - 4 Mm 192 391 75,072.00 15 Pc Glass, White Wine Packed In Carton Box Glass, White Wine Food And Beverage Services Nc Ii Type: Royalty Body Shape: Balloon Shaped Bowl Material: Crystal Clear Glass Rim Diameter : 55 - 60 Mm Thickness : 1.5 - 3 Mm Over -all Length : 200 -220 Mm Capacity : 270 - 300 Ml Stem Diameter : 6 - 8 Mm Stem Length : 75 - 85 Mm Base Diameter : 70 - 80 Mm Base Thickness : 2 - 5 Mm 192 321 61,632.00 16 Pc Gravy Boats Type: Steel Type Body Shape: Boat Shape With Handle Material: Stainless Steel Capacity : 5 Oz. Appearance: Mirror Polish Finish Size :17cm X 7.3cm X 8.2 Cm / 6.7 X 2.9 X 3.2 Inches (minimum) The Item Must Have Good Quality Packed In Plastic Pouch 192 815 156,480.00 17 Pc Ice Bucket, 2 Liters With Tongs Type: Steel Type Body Shape: Circular Set Includes: A. Ice Bucket Material : Stainless Steel Diameter : 140 - 180 Mm Height : 140 - 170 Mm Thickness Of Bucket : 0.7 - 2 Mm Capacity : 2 Liters (minimum) The Item Must Have Good Quality C34 16 312 4,992.00 18 Pc Knife, Butter 1. Material : Stainless Steel W/ Highly Polished Appearance 2. Over-all Length : 140 Mm - 150 Mm 3. Handle Thickness : 3 Mm - 5 Mm 4. With Dull Edge And Rounded Tip 5. The Item Must Have Good Quality. 6. Packed In Carton Box 192 260 49,920.00 19 Pc Knife, Dinner Type: Dinner Knife Body Shape: Flat With Round Tip Material / Appearance : Stainless Steel Blade Highly Polished Handle Material : Stainless Steel Overall Length : 160 - 190 Mm Blade Thickness : 2 - 4 Mmhandle Thickness : 3 - 6 Mm Serrated Blade With Rounded Tip Packed In Carton Box The Item Must Have Good Quality 192 234 44,928.00 20 Pc Knife, Fish Type : Fish Knife Body Shape: Flat With Pointed Tip Material / Appearance : Stainless Steel, Highly Polished W/ Plain Design Overall Length : 200 - 220 Mm Width Blade : 20 - 25 Mm Thickness Of Blade : 2 Mm - 4 Mm Thickness Of Handle: 3 Mm - 6 Mm Wide Blade, Dull Edge, Tip Made With A Notched Point Color : Silver Packed In Carton Box The Item Must Have Good Quality 192 279 53,568.00 21 Pc Menu Folder Type : Dining Side Chair Body Shape: Square Material : Metal (round Or Square) Dimesion: Total Height - 33" X 15" X15" (minimum) Capacity: 150 Kg. Black Colored Powder Coated Frame With Foam On Seat Packed In Carton Box The Item Must Have Good Quality 16 259.00 4,144.00 22 Pc Napkin Holder Type: Steel Type Body Shape: Rectangular Material : Stainless Steel With Highly Polished Appearance Dimension : Width : 70 - 90 Mm X Length : 150 - 170 Mm , Thickness : 0.7 Mm -2 Mm Packed In Plastic Pouch The Item Must Have Good Quality 48 499.00 23,952.00 23 Pc Order Pads Type: Numbered Pads Body Shape: Rectangular Material : 80 Gsm Offset Paper Each Pad Comes With A 100 Sheets And Corresponding Copy Page Each Pad Has Sequentially Numbered Orders To Make It Easy To Keep Track With 100 Sheets Per Pad And 10 Pads Included Can Take 1000 Orders Before You Run Out Packed In A Plastic Pouch 16 299.00 4,784.00 24 Pc Pepper And Salt Mill Type: Pepper & Salt Mill Body Shape: Round Body Material: Wood Size: Diameter: 5 Cm X Height: 20 Cm (minimum) Carved Of Wood With Stainless Steel Grinding Mechanism Color: Natural Screw Cap At The Top Of The Mill To Adjust The Thickness Of Peeper Or Spices Preferably With A Packing Case Food Grade And Nontoxic Must Be Branded 16 405.00 6,480.00 25 Pc Plate Covers Type: Steel Type Body Shape: Circular Material: Stainless Steel, Mirror Polished Diameter: 10 1/4 Inches (minimum) Height: 2 7/8 Inches (minimum) Thickness: 1/16 Inch. (minimum) With Handle Packed In Plastic Pouch The Item Must Have Good Quality 64 332.00 21,248.00 26 Pc Plate, Dessert, 7”to 8” Type: Plain Type Body Shape: Circular Material: Porcelain Supply Must Be A Set, Consisting Of One (1) Of Each: 7 Inches And 8 Inches Plates Color : White Inner Diameter: 145 To 165 Mm Thickness : 3 To 6 Mm Smooth And Glossy Surfaces Packed In Carton Box The Item Must Have Good Quality 192 315.00 60,480.00 27 Pc Plate, Dinner, 10” Type: Plain Type Body Shape: Circular Material: Porcelain With No Design Color: White Inner Diameter : 200 Mm - 215 Mm Outer Diameter : 250 - 260 Mm Thickness : 3 Mm - 6 Mm Smooth And Glossy Surfaces Packed In Carton Box The Item Must Have Good Quality 192 373.75 71,760.00 28 Pc Plate, Fish, 8” To 9” Type: Plain Type Body Shape: Circular Material : Porcelain With No Design Supply Shall Be A Set Consisting Of: One (1) Each 8 Inches And One (1) Each, 9 Inches Color : White Inner Diameter : 165 Mm - 190 Mm (minimum) Thickness : 3 Mm - 6 Mm Smooth And Glossy Surfaces Packed In Carton Box The Item Must Have Good Quality 192 310.00 59,520.00 29 Pc Round Table (8's) Type : Dining Side Chair Body Shape: Square Material : Metal (round Or Square) Dimesion: Total Height - 33" X 15" X15" (minimum) Capacity: 150 Kg. Black Colored Powder Coated Frame With Foam On Seat Packed In Carton Box The Item Must Have Good Quality 16 20,000.00 320,000.00 30 Pc Salad Forks Type: Salad Fork Body Shape: Fork Shape Material/appearance: Stainless Steel, Highly Polished, With 4 Tines Length: 150 Mm - 175 Mm Thickness Of Handle : 2 Mm - 3 Mm Color: Silver Packed In Plastic Pouch The Item Must Be Of Good Quality 192 345.00 66,240.00 31 Pc Salad Knife Type: Salad Knife Body Shape: Semi Rectangular Blade With Pointed Tip Material/appearance: Stainless Steel, Highly Polished, W/ Plain Design Overall Length: 145 -160 Mm Blade Thickness: 2 Mm To 4 Mm Handle Thickness: 4 Mm To 6 Mm Handle Material: Stainless Steel Rounded Tip Handle Packed In Carton Box The Item Must Have Good Quality 192 329.00 63,168.00 32 Pc Salad Plates 7” To 8” Type: Plain Type Body Shape: Circular Material: Porcelain With No Design Supply Must Be A Set Consisting Of One (1) Each: 7 Inches And 8 Inches Plates Color: White Diameter (inner): 150 Mm - 165 Mm Thickness: 3 Mm - 6 Mm Smooth And Glossy Surfaces Packed In Carton Box The Item Must Have Good Quality 192 342.00 65,664.00 33 Pc Salt And Pepper Shakers Type: Glass Type Body Shape: Square Material: Glass And Aluminum Over-all Height: 75 -90 Mm Length: 50 -60 Mm Width: 50 -60 Mm Aluminum Cover Packed In Carton Box The Item Must Have Good Quality 32 379.00 12,128.00 34 Pc Sauce Ladles Type: Spouted Bowl Body Shape: Circular With Pouring Spout Material: Stainless Steel, Highly Polished Appearance Over-all Length: 220 -230 Mm Ladle Bowl Length: 60 -65 Mm Long Ladle Bowl Diameter: 65 -70 Mm Depth: 10 -15 Mm Handle Details: 150-155 Mm Long X 20 -30 Mm Wide X 2 - 4 Mm Thick Color: Silver With Hang Hole For Hanging And Easy Access Dishwasher Safe Packed In Plastic Pouch The Item Must Have Good Quality 16 409.00 6,544.00 35 Pc Server, Cake 1. Material : Stainless Steel Blade , Highly Polished Appearance 2. Over-all Length : 220 To 270 Mm 3. Width : 60 - 80 Mm 4. Thickness : 1.5 Mm To 2 Mm 5. Handle : 120 -140 Mm Long, Non-toxic Plastic 6. Shape : Shovel-shaped 7. Color : Silver 8. The Item Must Have Good Quality 9. Packed In Carton Box 16 421.00 6,736.00 36 Pc Service Forks Type : Service Fork Body Shape: Fork Shape Material/appearance: Stainless Steel, Highly Polished, W/ Palin Design Over-all Length: 220 Mm - 260 Mm Width: 20 - 25 Mm Handle Thickness: 1.5 Mm - 4 Mm Handle Length - 165 Mm - 185 Mm 4 Tines Color: Silver Packed In Plastic Pouch 48 499.00 23,952.00 37 Pc Service Tray Type: Plastic Body Shape: Rectangular Material: Plastic (pp) Size : 14 Inches X 18 Inches X 1 Inch (minimum) Color : Any Packed In Plastic Pouch The Item Must Have Good Quality 48 542.00 26,016.00 38 Pc Show/service/ Base Plates 11” To 14” Type: Plain Type Body Shape: Round Material: Porcelain With No Design Supply Must Be A Set Consisting (1) Of Each: - 11 Inches, - 12 Inches, - 13 Inches, And - 14 Inches Plates Color: White Diameter, Inner : 225 Mm - 250 Mm Thickness: 3 Mm - 6 Mm Smooth And Glossy Surfaces 48 509.00 24,432.00 39 Pc Side Plates Or Bread Plates 6” Type: Plain Type Body Shape: Round Material: Porcelain With No Design Color: White Inner Diameter: 95 Mm To 120 Mm Outer Diameter: 145 Mm To 170 Mm Thickness : 3 Mm - 6mm Smooth And Glossy Surfaces Packed In Carton Box The Item Must Have Good Quality 192 306.00 58,752.00 40 Pc Side Towels Type: Chef's Towel Body Shape: Rectangular Material: Oxford Polyester Soft Cloth Over-all Length : 640 - 680 Mm Over-all Width : 420 -460 Mm Color : Plain White Packed In Plastic Pouch The Item Must Have Good Quality 32 270.00 8,640.00 41 Pc Silver Platter Type: Steel Type Body Shape: Round Material: Stainless Steel Diameter: 300 -330 Mm Thickness: 1 - 2 Mm Packed In Plastic Pouch The Item Must Have Good Quality 64 422.00 27,008.00 42 Pc Soup Bowl Type: Plain With Two Handles Body Shape: Circular Material : Porcelain Capacity : 24 Oz. (minimum) Packed In Carton Box The Item Must Have Good Quality Packed In A Carton Box 192 499.00 95,808.00 43 Pc Soup Ladle Type: Steel Type Body Shape: Circular Material: Stainless Steel, Highly Polished Appearance Over-all Length : 220 -235 Mm Ladle Bowl Details : 60 -65 Mm Long, 60 -75 Mm Diameter, 10 -15 Mm Deep Handle Details : 145 - 155 Mm Long X 12 - 25 Mm Wide X 1.5 -3 Mm Thick Color : Silver With Hang Hole For Hanging And Easy Access 16 347.00 5,552.00 44 Pc Soup Tureen Type: Steel Body Shape: Round Material: Stainless Steel Capacity: 7 - 11 Quart Size : 60 X 35 X 32 Cm (minimum) Packed In Plastic Pouch The Item Must Have Good Quality 32 1,835.00 58,720.00 45 Pc Spoon, Dessert Type : Dessert Spoon Body Shape: Oval Material/appearance: Stainless Steel, Highly Polished With Plain Design Over-all Length : 175 To 190 Mm Thickness : 2 Mm - 3 Mm Shorter Handle : 120 -130 Mm Color : Silver Packed In Plastic Pouch The Item Must Have Good Quality 192 358.00 68,736.00 46 Pc Spoons, Service Type : Service Spoon Body Shape: Oval Material: Stainless Steel, Highly Polished, W/ Plain Design Over-all Length: 220 Mm - 250 Mm Width: 30 - 38 Mm Handle Thickness: 1.5 Mm - 4 Mm Handle Length - 165 Mm - 185 Mm Color: Silver Packed In Plastic Pouch The Item Must Have Good Quality 48 354.00 16,992.00 47 Pc Spoons, Soup (cream And Consume) Type: Soup Spoon Body Shape: Round Material/appearance : Stainless Steel, Highly Polished, W/ Plain Design, Rounded Tip Handle Over-all Length : 165 Mm - 200 Mm Smaller Oval Shaped Spoon Bowl And Tapers Slightly To The Tip Shorter Handle : 110 Mm - 170 Mm Thickness : 1.5 Mm - 3 Mm Color : Silver Packed In Plastic Pouch 192 289.00 55,488.00 48 Pc Steak Knife Type: Steak Knife Body Shape: Flat With Serrated Edge Material: Stainless Steel Steel Blade With Wooden Handle Length: 170 Mm To 203 Mm Handle Wood Thickness: 10 - 14 Mm With Serrated Blade Packed In Carton Box The Item Must Have Good Quality 192 387.00 74,304.00 49 Pc Sugar Container The Item Must Have Good Quality Sugar Container Food And Beverage Services Nc Ii Type: Glass Type Body Shape: Round Material: Glass With Brass Lid (or Equivalent) Diameter: 70 -80 Mm Height: 130 -140 Mm Capacity: 12 Oz. Packed In Carton Box The Item Must Have Good Quality 40 537.00 21,480.00 50 Pc Table Cloth, 54 X 54 Inches Type: Plain Cloth Body Shape: Square Material: Oxford Polyester Cloth Color: Plain White Dimension: L 54 Inches X W 54 Inches (minimum) Packed In Plastic Pouch The Item Must Have Good Quality 24 2,800.00 67,200.00 51 Pc Table Cloth, Rectangular Type: Plain Cloth Body Shape: Rectangle Material : Linen Size : 120cm X160cm (minimum) Color : Any Color But Not Black Feature: Washable Packed In A Plastic Pouch 16 2,500.00 40,000.00 52 Pc Table Napkins, Cloth, 16” X 16” Type: Plain Cloth Body Shape: Square Material: Oxford Polyester Cloth Or Its Equivalent Size: L 16 Inches X W 16 Inches (minimum) Color: Plain White Packed In Plastic Pouch The Item Must Have Good Quality 240 120.00 28,800.00 53 Pc Table Skirtingcloth 90”x90” Ttype: Plain Cloth Body Shape: Square Material: American Cotton Twill Cloth Color: Any Color Except Black Dimension: 90 Inches X 90 Inches (minimum) Packed In Plastic Pouch The Item Must Have Good Quality 16 3,200.00 51,200.00 54 Pc Table, Square/rectangular (4's Or 6's) Type: Foldble Plastic Body Shape: Square/rectangle Materia: High Density Polyethylene Table Top Powder Coated Steel Frame Dimension: 37 - 39 X 37 - 39 Inches Color: White Good For 4 Persons Packed In Carton Box The Item Must Have Good Quality 32 20,000.00 640,000.00 55 Pc Tea Pot, 2 Pints Type: Porcelain Type Body Shape: Round With Handle And Pouring Spout Material : Porcelain Capacity : (2 Pint) Color : White Packed In Carton Box The Item Must Be Of Good Quality 16 1,997.00 31,952.00 56 Pc Teaspoon Type : Tea Spoon Body Shape: Oval Tip Material/appearance: Stainless Steel, Highly Polished, W/ Plain Design Over-all Length: 120 Mm To 140 Mm Handle Thickness: 2 Mm To 4 Mm Short Handle Length - 100 Mm (minimum) Color: Silver Packed In Plastic Pouch The Item Must Have Good Quality 124 239.00 29,636.00 57 Pc Tong, 8 Inches Type: Tong, 8 Inches Body Shape: Standard Material: Stainless Steel Size: 8 Inches Stainless-steel Arms With Soft, Comfortable Grips Nylon Heads Safe For Nonstick Cookware Heat-resistant Up To 400 Degrees Fahrenheit Tongs Lock Closed For Storage Preferably With A Packing Case Food Grade And Dishwasher-safe Must Be Branded 16 289.00 4,624.00 58 Pc Tooth Pick Holder Type: Steel Type Body Shape: Round Material: Stainless Steel, Highly Polished In Appearance Diameter: 30 -35 Mm Diameter (minimum) Height: 65 -75 Mm Capacity: 1.24 Oz. (minimum) Packed In Plastic Pouch The Item Must Have Good Quality 24 715.00 17,160.00 59 Pc Tray Stand Type: Foldable Body Shape: Rectangular Material: Chrome Plated Metal Folding Tray Stand Length: 470 -490 Mm Width: 400 -440 Mm Height: 770 -790 Mm Packed In Plastic Pouch The Item Must Have Good Quality 16 7500 120,000.00 60 Pc Tray, Bill Folders/ Change 1. Material : Heavy Duty Plastic ( Abs ) Or Its Equivalent 2. Height : 190 - 220 Mm 3. Width : 120 -140 Mm 4. Thickness : 2 Mm To 3 Mm (minimum) 5. Color : Black 6. With Check And Pen Holder 7. The Item Must Have Good Quality 8. Packed In Plastic Pouch 16 384.00 6,144.00 61 Pc Tray, Round (bar) Type: Plastic Body Shape: Round Material: ( Pe/abs) Plastic Rubberized Surface, Non-slip/grip Tight Over-all Diameter: 345 -360 Mm (minimum) Thickness: 2 - 4 Mm (minimum) Color: Black Packed In Plastic Pouch The Item Must Have Good Quality 40 2,990.00 119,600.00 62 Pc Water Goblet Type: Water Goblet Body Shape: Balloon-shaped Bowl Material: Crystal Clear Glass Over-all Length: 200 -220 Mm Capacity: 270 Ml To 300 Ml Rim Diameter - 55 -65 Mm Thickness: 1 Mm To 3 Mm Stem Length : 75 -85 Mm Stem Diameter : 6 -8 Mm Base Thickness : 3 -4 Mm Base Diameter : 7 -80 Mm Packed In Carton Box The Item Must Have Good Quality 184 399.00 73,416.00 63 Pc Water Pitcher Type: Steel Type Body Shape: Circular Material: Stainless Steel, Highly Polished Appearance Height: 170 Mm To 220 Mm Top Diameter: 110 -120 Mm (approximate) Capacity: 1 - 1.5 Liter With Pour Spout Dishwasher Safe Packed In Plastic Pouch The Item Must Have Good Quality 40 1,433.30 57,332.00 Total 4,569,960.00 Lot E: Fron Desk Office 1 Pack First Aide Kit (bandages,antiseptic Wipes, Gauze Pads,tape,gloves And Pain Reliever) 5 ₱1,000.00 5,000.00 2 Pcs Megaphone (long Range Megaphone) Siren, Aux Input,usb/sd Port, Voice Recorder, Handy And Light Weight, 60w , 60 Meters Range 2 ₱5,045.00 10,090.00 3 Pcs Whistle Whistle Plus Echo Whistle Black 2 ₱500.00 ₱1,000.00 4 Pcs White Board Magnetic 30x45(cm) 4 ₱1,000.00 ₱4,000.00 5 Sets Camera 4k Digital Camera For Photography And Video, Autofocus Anti-shake 48mp Vlogging Camera, 3” 180 Flip Screen Camera With Flash 16x Zoom, Digital Camera With 32gb Card Battery Charger Black 1 ₱3,000.00 ₱3,000.00 6 Sets Calculator Mh-16 Bk(black) 30 ₱825.00 24,750.00 7 Sets Cart, Bell Boy Large-1340(l) X 680 (w) X 1930 (h)mm 2 ₱10,000.00 20,000.00 8 Sets Cash Register With Drawer Logicowl Oj-405c Full Metal Pos Cash Drawer Heavy Duty With Rj11 Interface 2 ₱5,500.00 11,000.00 9 Sets Credit Card Imprinter 4850 Flatbed Imprinter 1 ₱5,492.00 5,492.00 10 Sets Credit Card Voucher Holder 5 ₱3,000.00 15,000.00 11 Sets Detector, Fake Bills Philippine Counterfeit Currency Detector Cash Count Statistical Amounts With Led Display Automatic 2 ₱5,000.00 10,000.00 12 Pcs Guest Follo Rack 10 1,000.00 10,000.00 13 Unit Hypercom T7p T Pos Credit Card Terminal With Original Power Supply And Box 2 2,000.00 4,000.00 14 Unit Key Card Marker With Verifier 2 2,000.00 4,000.00 15 Sets Safety Deposit Box/drop Vault With Lcd Electronic Lock & 2 Backup Keys 2 4,000.00 8,000.00 16 Unit Speaker Lapel Original Trident Tp-638 Rechargeable Lapel Mini Speaker With Mic 65 1,500.00 97,500.00 Total ₱232,832.00 Lot F: Hairdressing 1 Pc Body Brush Prosthetic Material: Stiff Nylon Bristle Size: At Least 41.8 Cm X 6.5 Cm (over-all Size) Brush Height: 8mm(minimum) With Wooden Handle" 30 65 1,950.00 2 Pc Bowl, Mixing Plastic Material: Plastic Inner Diameter: 10.5 Cm (minimum) Height: 6cm (minimum) Thickness Is 2mm (minimum) Any Color Non Toxic 54 75 4,050.00 3 Set Bowl, Shampoo Bowl Material: Abs Plastic With Adjustable Stand (height: 39 Inches To 54 Inches) Minimum Bowl Dimensions: 19 Inches(l) X 20 Inches(w) X 10 Inches(h); With Sealed Foam Rubber Neck Rest For Shampoo Bowls With Hose Attachment Of 7 Ft. Long(minimum) Stainless Steel Frame Portable Type Packed With Shipping Carton Boх Branded 12 7,000 84,000.00 4 Brush Applicator Material: Plastic Non Toxic Size: Small=190mm Length Medium=270mm Large=300mm Handle Width:70mm (minimum) Width Of Tip: 80mm (minimum) With Hair Coloring Dyeing Board Packed With Plastic Pouch 60 50 3,000.00 5 Brush Hair Material: Plastic Bristle Paddle Brush Type Wooden Handle Minimum Width: 2 Inches Non Toxic Packed With Protective Carton Box 60 100 6,000.00 6 Cap Frosting, With Hook Cap Material: Silicone Type:reusable, Perforated Cap One Size Fits All Or At Least 31cm X 22cm With Pre-cut Tipping Guides With Bleed Proof Inher Liner With A Rounded Metal Hook To Pull Hair Through The Ready Made Perforations Packed With Plastic Pouch 33 210 6,930.00 7 Waterproof Cloth Cordless Type To Fit An Average Size Head (21-24 Inches) Stretch Unisex Up To 29 Inches Hair Care Treatment Styling Reversible And Reusable, Non Toxіс Includes With User's Guide In English That Contains: A. Diagram Of The Parts With Their Names B. Operating Procedure On How To Use The Equipment C. Safety Precaution When Using The Equipment D. Basic Troubleshooting And Maintenance Procedure 30 510 15,300.00 8 Cape Polyester Cloth Size: At Least 125 Cm X 140 Cm Hairstyling Type Non Toxic Packed With Plastic Pouch 30 250 7,500.00 9 Chair, Hydraulic Material:metal Base Size:length59 Cm, Width54 Cm, Height From 51-78cm Hydraulic Pump Can Be Up And Down By Pedaling Load Capacity:180kg Hydraulic Styling Chair Type Heavy Duty Hydraulic Pump For Height Adjustable And 360 Rotation Hydraulic Pump Build In For Adjusting The Seating Height. With Foot Rest 30 7550 226,500.00 10 Clamp Material: Plastic Overall Length: 9.5cm Thickness:10mm(mini Mum) Hairstyling Clamp Type 60 50 3,000.00 11 Clamp, Duck Bill Material: Metal Length: 11 Cm (minimum) High Elasticity Stainless Steel Spring. Non Slip Handle Packed With Plastic Pouch Branded 60 60 3,600.00 12 Hair Clipper Body Material:hard Plastic Blade Materíal: Carbon Steel Capacity:6 Watts (minimum) Complete With Blade Guard And 4 Comb Attachments (#1, #2, #3, #4) Motor:magnetic Typе, Corded,12v Ac/dc Adaptor Delivers 1,400 Strokes Per Minute, With Complete Accessories Including The Cleaning Brush With Cord 2 Meters Length Minimum With User's Manual In English Which Includes: A. Parts Manual With Labels, B. Assembly Instructions, C. Operating Procedures, Packed With Protective Carton Box Branded 30 2580 77,400.00 13 Pc. Comb, Afro Material: Plastic Size: Over All Length At Least 7 Inches Width: 3.25 Inches(minimum) Number Of Teeth: 12 Teeth (minimum); Teeth Height: 2.5 10 Inches Long (minimum) 30 85 2,550.00 14 Pc. Comb, All Purpose Material:plastic Size#3 Or At Least 18 Cm Long (minimum) Has Both Fine And Medium Teeth Position On One Side Only Height Of The Teeth: 2 Cm (minimum) Non Toxic Packed With Plastic Pouch 30 35 1,050.00 15 Pc. Comb, Haircutting Material: Hard Plastic Length Including The Handle:180mm (minimum) Width: 30mm ( Minimum) With Detachable Steel Blades And Blade Holder With Two Sides For Different Cuts With Extra Blades 30 25 750.00 16 Pc. Comb, Large Toothed Material: Plastic Size: At Least 15 Cm Number Of Teeth: 10 Teeth (minimum) Gap Between Comb's Teeth: 0.4 To 0.5 Cm Gap From One Another Teeth Size:at Least 0.3 Cm In Width X 4cm In Length Non Toxic Packed With Plastic Pouch 30 25 750.00 17 Pc. Comb, Tail Material:plastic Size: 8 Inches(l)minimum X 1 Inches (w) Minimum Tail Length: 4 Inches(minimum) Tooth Length: 3/4 Inch(minimum) Packed With Plastic Pouch 30 25 750.00 18 Pc. Comb, Teasing Material:plastic With 2 Rows Of Teeth 1st Row:large Teeth With At Least 25 Mm Long 2nd Row: Small Teeth With At Least 19 Mm Long Over-all Comb Size: 20 Cm (l) Minimum X 3.8 Cm (w) Minimum Non Toxic Packed With Plastic Pouch 30 25 750.00 19 Pc. Comb, Wide Tooth Material: Plastic Size: At Least 15 Cm Number Of Teeth: 10 Teeth (minimum) Gap Between Comb's Teeth: 0.4 To 0.5 Cm Gap From One Another Teeth Size:at Least 0.3 Cm In Width X 4cm In Length 30 25 750.00 20 Pc. Crimpers Power: 25 Watts(minimum) Size: At Least 38 Cm X 15.5 Cm X 9 Cm Maximum Temperature: 200 Degrees Centigrade With Variable Heat Setting. With On/off Switch Button Rated Voltage: 110- 230volts Ac With Power Cord With Plastic Handle 30 1850 55,500.00 21 Pc. Curling Iron Ceramic Curling Iron Capacity: 65watts Voltage: 210-240volts Ac With Power Cord Barrel Size: 1 Inch (minimum) Adjustable Heat Setting With Maximum Temperature Of 200 Degrees Centigrade. Swivel Cord Up To 360 Degree 12 2,550.00 30,600.00 22 Pc. Drip Pan Material: 25-02-022 Hard Plastic Size: At Least 17.5 X 25.8 X 1 Inches Thickness: 1/8 Inch (minimum) Shallow Rectangular Type Packed With Carton Box 15 260.00 3,900.00 23 Pc. Dryer Hair Power: 1000w Rated Voltage: 220vac At Least (l X W X H): 18.5cm X 16cm X 6.5cm With Plastic Handle Design Packed With Carton Box With Styrofoam Holder With User's Manual In English Which Includes: A. Parts Manual With Labels, B. Assembly Instructions 21 260.00 5,460.00 24 Pc Gloves, Disposable Material: Plastic 10 Size: At Least 25cm X 23cm Packaging Is 100 Pcs Per Box 12 103.00 1,236.00 25 Pc Gloves Rubber Size: Medium Thickness: 4 Mil Acid Resistant Packed With Plastic Pouch In Pairs. 30 270.00 8,100.00 26 Pc Gown Smock Material: Polyester Sizes: 1 Piece = Small Size At Least (50 Inches X 56 Inches); 1 Piece= Medium Size,at Least (52 Inches X 58 Inches); 1 Piece= Large Size, At Least (54 Inches X 60 Inches); Packed With Plstic Pouch Per Size 24 260.00 6,240.00 27 Pc Hairclips Material: Metal Size:at Least 67mm X 25-02-027 19mm Non Corrosive Packed With Plastic Pouch 18 420.00 7,560.00 28 Pc Hairnet Invisible Material:nylon Size: 55mm Type (minimum) Stretchable And Unisex Color: Black Non Toxic Packed With Plastic Pouch 15 240.00 3,600.00 29 Pc Headband Size: 6 Inches (minimum) Woven Crochet Tube Top Headband Very Stretchy, Soft Material, Comfortable And Breathable 21 75.00 1,575.00 30 Pc Headband Flannel Flannel Cloth Size: At Least 45 Cm (unstretched Circumference) Width: 8 Cm (minimum) 21 75.00 1,575.00 31 Pc Mirror Hand Mirror Size 15 Cm Diameter (minimum) Frame Thickness Including Mirror Glass: 6.5mm(minimum) Over-all Length With The Handle Is 20 Cm (minimum) Clear Mirror With No Distortion (minimum) Frame And Handle Are Made Of Plastic Plane Mirror Type Packed With Carton Box With Styrofoam Protection 15 75.00 1,125.00 32 Pc Mirror Modular Mirror Type: Plain Imirror Mirror Material: Glass Frame Material: Aluminum (cut To Fit) Dimensions (hxw): 75 Cm X 65 Cm (minimym) Mirror Thickness: 6mm (minimum) 15 21.20 318.00 33 Pc Prong Clip Double Material: Steel Nickel Or Chrome Base Plated Size: 45 Mm Minimum Hairstyling Clip Type Packed With Plastic Handle 18 45.00 810.00 34 Pc Prong Clip Single Material: Steel, Plated Size: 55 Mm (minimum) Type: Single-prong Clip Packed With Plastic Pouch 18 65.00 1,170.00 35 Pc Razor Straight Blade Material: High Carbon Steel Type: Foldable Straight Razor, Replaceable Blade; Dimensions (lxw): 14 Cm X 2 Cm (minimum) When Folded; Compatible With Double-edged Razor Blades; Package Includes 10 Pieces Blade/box Non Corrosive Branded 30 90.00 2,700.00 36 Pc Roller Pins Material: Metal Size: 60mm Long (minimum) Application: Hair Roller Pins Quantity By Dozen(12 Pieces) Non Corrosive Packed With Plastic Pouch 30 60.00 1,800.00 37 Pc Rollers Large Sized Material: Plastic Size: At Least 40mm Diameter X 60mm Long Hairstyling Type Packed With Plastic Pouch 30 225.00 6,750.00 38 Pc Rollers Medium Material: Plastic;diameter: 38mm (minimum) Length: 58mm (minimum) Hairstyling Type Packed With Plastic Pouch 30 210.00 6,300.00 39 Pc Rollers,jumbo Material:plastic Approximately 44mm In Diameter X 64mm Long 30 250.00 7,500.00 40 Pc Scissor Cutting Material:stainless Steel Total Length: 17cm (minimum) Blade Width At Least 10 Cm Non Corrosive Packed With Plastic Pouch Branded 36 250.00 9,000.00 41 Pc Scoop Material: Plastic Capacity:1/2 Cup (minimum) Rounded Edges With Handle Thickness: 1.5 Mm (minimum) 36 175.00 6,300.00 42 Pc Shower Cap Material: Plastic Size: One Size Fits All Or 30cm Reusable And Waterproof Packed With Plastic Pouch 60 45.00 2,700.00 43 Pc Spatula Material:plastic Dimension: Over-all Length Of 7.5 Cm Long, X 1.5 Cm Wide (minimum) Application:hair Waxing Removal Packed With Plastic Pouch 60 90.00 5,400.00 44 Pc Spray Bottle Material: Transparent Plastic Capacity: 300ml (minimum) Trigger Type Sprayer Dimension: At Least Diameter Of Bottom Is 7 Cm And The Height Is 17cm 60 75.00 4,500.00 45 Unit Steamer Hair Power 450 Watts (minimum) Rating Is 220 Volts/50- 60hz Hood Material: Polycarbonate Hood Has At Least 30 Cm Diameter Opening X 25 Cm Deep Timer Setting Is Up To 60 Minutes With At Least 32 Ounce Water Reservoir Adjustable Height From 100 To 150cm With At Least 5 Swivel Caster With User's Manual In English Which Includes: A. Parts Manual With Labels, B. Assembly Instructions, C. Operating Procedures, Branded 15 7,200.00 108,000.00 46 Pc Stool Material: Metal, Electroplated Load Capacity: 150kg Design: Swivel Stool With Backrest With Hydraulic Lift To Adjust Height Freely. With Thick Sponge Cushion. With At Least Four Caster Wheels. With Thick Sponge Cushion. Swivel Stool With Backrest No Sharp Edges Branded 60 1,820.00 109,200.00 47 Unit Infrared Iron Material: Lonic Ceramic Tourmaline-infused Plates And Abs Plastic Body Power: 70 Watts (minimum) Power Rating: 220-240 Volts Ac; Over-all Size: 24 Cm Long (minimum) Heating Plate Size Up To 50 Mm Heating Time: Within 30 Seconds; Variable Heat Settings: From 250 To 450 Degrees Fahrenheit With Digital Temperature Control Safety Mode: Auto Shut Off After 60 Minutes; With Swivel Cord Comes With Storage Pouch Branded 27 4,593.00 124,011.00 Total 969,510.00 1 Unit Dummy,anatomical 1. Half Life-size Muscular Figure Measures 32" Tall (minimum). 2. This Model Features 27 Removable Parts That Are Held On By Metal, Screws, Posts And Hooks. 3. It Shows The Muscular System With Numbered Parts That Comes With A Corresponding Key. 4. It Has Removable Arms, A Calvarium, And A Removable Chest Plate That Hides The Individual Numbered Organs Of The Digestive—system. 5.detachable Muscles Include: Deltoid, Brachioradialis With Extensor Carpi Radialis Longus And Brevis, Biceps Brachii, Pronator Teres With Palmaris Longus And Flexor Carpi Radialis, Sartorius Muscle, Rectus Femoris, Extensor Digitorum Longus, Tensor Faciae Latae, Gluteus Maximus, Biceps Femoris, Semitendinosus, Gastrocnemius, Soleus. 6. Removable Organs Include: Brain (2parts), Lungs (2 Pacts), Heart (2) , Liver, Intestines, Stomach 7. Base Is 13" X 9" (removable) 8. Weighs 12 Lbs. (approximately) 9. Plastic Material 10. Non Toxic Material 11. Carton Box Packaging 3 4800 14,400.00 2 Unit Massage Bed/table Materials: Hard Wood With Steel Bracings, Hardwood Frame, Marine Plywood Deck; Color: Black Dimensions: W:75 Cm X L:183 Cm X H: (adjustable) Height: Adjustable From 24 In. - 33in. Leg Thickness - 35mm (minimum) Cushion System: High Density Foam (7.5 Cm / 2.95") Minimum With Pu Leather Cover (1mm Thick) Finishing: Round Corner Weight Capacity: 250 Kg(minimum) Gross Weight: 21 Kg (approximate) 2 End Support Bearer To Strengthen The Base And Increase Weight Capacity Accessories - Aluminum Headrest (adjustable) + Face Plug + Armrest + Arm Sling + Carry Case Portable And Foldable 30 5500 165,000.00 3 Set Massage Chair 1. Padded With 3" Thick, High-density, Small-cell Foam 2. Size: 14"-diameter Seat (minimum) But Without Back And Arm Rest, With Metal Post And Hard Plastic Star. 3. Pneumatic Spring Will Effortlessly Adjust The Height From 18" To 24" With The Pull Of A Lever 4. Five Heavy-duty, Smooth-rolling Wheels 5. Load Capacity: 265 Lbs / 120 Kg (maximum) 6. Smooth Surface And No Sharp Edges 7. Any Color With One Color Only For Whole Lot 30 6,000 180,000.00 4 Pc Sphygmomanometer Aneroid Type; (for Adult Use) Large Cuff Sizes: 33 To 42 Cm Arm Diameters Accuracy: ±3mm Hg; Measurement Range : 0mm Hg To 300mm Hg; Smallest Scale: 1mm Hgindex And Range Markings On The Dial For Clear Readings Nylon Cuff Is Durable And Stain Resistant With A Velcro Closure Inflation System Is Latex Free And Has An Easy-release Deflation Valve Chrome-plated Brass Air Release Valve; Set Includes: 1 Unit Sphygmomanometer; 1 Zippered Nylon Carrying Case Smooth Surface And Edges, Non Toxic Material 30 2000 60,000.00 5 Pc Stethoscope Chest-piece Description: Stainless Steel Double Chest Piece Color: Black Tubing Description: Y-tube Pvc Uses Extra Soft Replaceable And Pivotable Ear Tips The Binaural Is Chromium-plated Chest-piece Diameter: 44 Mm (minimum) And Has Non-chill Rim Overall Length: 29" /74 Cm (minimum) The Stethoscope Is Latex-free Comes With A Pair Of Replacement Ear Tips, A Replacement Membrane, And A Name Plate Smooth Surface And No Sharp Edges 30 2000 60,000.00 6 Pc Talking Sphygmomanometer Type: Arm Type Blood Pressure Monitor (talking English), Nylon Cuff Sizes: 33 To 42 Cm Arm Dia. Lcd Digital Display: Systolic, Diastolic, Pulse Rate With Real Voice, Loud And Clear, Announcing Blood Pressure Automatically When Reading Is Detected And Displayed Simultaneously Dimensions: 98mm*126mm*60mm (approximate) Hard Plastic Casing, Smooth Surface And No Sharp Edges, Non Toxic Materials Measurement Range : 0mm Hg To 300mm Hg; Smallest Scale: 1mm Hg Weight: 450g (approximate) Pressure Measurement Range: 20~280mmhg(0.4kpa-37.3kpa) Pressure Accuracy: ±3mmhg(±0.4kpa) Pulse Measurement Range: 40 ~199 Beats /min Voltage: 4*aaa Alkaline Batteries Or Power Adapter Certificate: Ce Rohs Intelligent Automatic Pressurization And Decompression Incorrect Prompting Function Automatic Shutdown: 1 Min After Last Operation Carton Box Packaging 30 1500 45,000.00 7 Pc Talking Thermometer Case Material: Hard Plastic Sensing Unit: Thermistor Measurement Method: Actual Measurement Measurement Range: 32 C - 42 C (89.6f-107.6f) Measurement Accuracy: ± 0.1c 32c-42.0c (± 0.2 F 89.6.9f-107.6f) Power Supply: 1.5v Dc, Lr41 Alkaline-magnesium Button Battery Real Voice (loud And Clear In English) Announces Temperature Automatically When Reading Is Detected Temperature Display: 3-digit, +deg C (deg F) Display In 0.1 Degree Increment Dimension Approx.: 2.0 (w) X 4.4 (h) X 1.2 (d) Inches (not Including Probe) / 51 (w) X 110 (h) X 30 (d) Mms (not Including Probe) Choices In Degrees Celsius Or Fahrenheit Talk Button Repeats Last Temperature Reading Last Reading Memory Auto Switch Off Accessories: Protective Case, 5 Probe Covers, Instruction Sheet Paddle Shape With Sensor On Small End 30 1400 42,000.00 8 Pc Thermometer, Digital Case Material: Hard Plastic Sensing Unit: Thermistor Measurement Method: Actual Measurement Measurement Range: 32 C - 42 C (89.6f-107.6f) Measurement Accuracy: ± 0.1c 32c-42.0c (± 0.2 F 89.6.9f-107.6f) Power Supply: 1.5v Dc, 1 Lr41 Alkaline-magnesium Button Battery When Measured At A Standard Room Temperature Of 23 Deg C (73.4 Deg F) In A Test Tank Held At Constant Temperature Power Consumption: 0.1mw Low Battery Indication: Battery Symbol Displayed Temperature Display: 3-digit, +deg C (deg F) Display In 0.1 Degree Increment Memory: Last Measuring Reading Beeper Function: 1 Beep When Power On 3 Beeps After Measurement Completed External Size (mm): 19.4(w) × 132.5 (l) × 10.0(d) Accessories: Protective Case, Test Battery, 5 Probe Covers, Instruction Sheet Paddle Shape With Sensor On Small End 30 350 10,500.00 9 Pc White Board White Board, Floor Standing, Rolling Board: White Formica Laminated, Plane Will Not Deform. Board Size: Rectangular 1800mm W X 1000 To 1200mm H, Board Edges Secured With Aluminum Clip Edging 17 Mm (minimum) Wih Plastic Corner Caps Comes With Metal Tray For Marker And Eraser The Stand And Frame Are Constructed With Aluminum Or Powder Coated Steel 25mm Square Tube (minimum), Sturdy, No Wobble With 4 Lockable Hard Plastic Caster Wheels Overall Height From Floor: 210 To 214cm Smooth Surface, No Sharp Edges 3 6038 18,114.00 Total 595,014.00 Over -all Total 16,580,027.00 Bids Received In Excess Of The Abc For Each Lot Shall Be Automatically Rejected At Bid Opening. 1. The Deped, Through The Bids And Awards Committee (bac), Now Invites Bids For The Above Procurement Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii (instructions To Bidders). 2. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) No. 9184. 3. Bidding Is Restricted To Filipino Citizens/sole Proprietorships, Cooperatives, And Partnerships Or Organizations With At Least Seventy Five Percent (75%) Interest Or Outstanding Capital Stock Belonging To Citizens Of The Philippines. 4. Interested Bidders May Obtain Further Information From The Deped Schools Division Office Surigao Del Sur At Telephone/cellphone No. 09853432707 And Inspect The Bidding Documents At The Address Indicated Herein For Issuance Of Bidding Documents During Office Hours. 5. For Those Who Are Interested To Purchase The Bidding Documents, A Complete Set Of Bidding Documents Shall Be Acquired From April 30, 2025 To May 14, 2025 By Interested Bidders From The Bids And Awards Committee Secretariat Deped Sdo –surigao Del Sur Only, Upon Accomplishing A Bidder’s Information Sheet And Payment Of A Non-refundable Fee For The Bidding Documents To The Deped Cashier. Amount Of Bidding Documents Shall Be As Follows: Lot A- Php. 10,000.00 Lot B- Php. 5,000.00 Lot C- Php. 500.00 Lot D- Php. 5,000.00 Lot E- Php. 500.00 Lot F- Php. 1,000.00 Lot G- Php. 1,000.00 6. The Department Of Education - Surigao Del Sur Division Will Hold A Pre-bid Conference On April 30, 2024 (wednesday) 10:00 Pm; 3rd Floor, Division Office Conference Hall, Balilahan, Mabua, Tandag City And Through Video Conferencing Or Webcasting Via Https://tinyurl.com/24ptf4ph Which Shall Be Open To Prospective Bidders. 7. Prospective Bidders Who Intend To Participate Are Required To Communicate With The Bac Secretariat Through Email At Surigaodelsur.procurement@deped.gov.ph For Confirmation And Accomplish The Online Pre-bid Conference Form Provided (annex B) On Or Before April 30, 2024 (wednesday) 10:00 Pm Upon Receipt Of This Form, The Bac Secretariat Will Send The Link Of The Meeting. 8. Submission Of Bids Must Be Dropped At The Drop Box Provided At 3rd Floor Conference Hall Deped Surigao Del Sur Division, Balilahan, Mabua, Tandag City May 14, 2025 (wednesday), At Exactly 1:30 Pm, Philippine Standard Time. Late Bids Shall Not Be Accepted. 9. Drop Off Point Of All Items Should Be In 27 District Offices Of Deped Surigao Del Sur With Free Delivery Cost. 10. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 14. 11. Bid Opening Shall Be On May 14, 2025 (wednesday), At Exactly 1:30 Pm; 3rd Floor, Division Office Conference Hall, Balilahan, Mabua, Tandag City. Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend The Activity And Also Via Microsoft Teams Https://tinyurl.com/mututj7w For The Purpose Of Constituting A Quorum, Both The Physical And Virtual Presence Of The Bac And Twg Members Shall Be Considered Pursuant To Gppb Resolution No. 09-2020. 12. The Deped - Surigao Del Sur Division Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Irr Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 13. For Further Information, Please Refer To: Bac Secretariat Balilahan, Mabua, Tandag City Surigaodelsur.procurement@deped.gov.ph 09853432707 Depedsurigaodelsur.com 14. You May Visit The Following Websites: For Downloading Of Bidding Documents: Https://notices.philgeps.gov.ph/ Https://www.deped.gov.ph/ Date: April 22, 2025 Laila F. Danaque, Edd, Ceso Vi (sgd) Chairperson

Details: Description Request For Quotation (rfq) 1 Lot Inks And Toners Rfq No. 2025-fad-002 The Department Of Environment And Natural Resources – Environmental Management Bureau – National Capital Region (denr-emb-ncr) Hereinafter Referred To As The “purchaser” Now Requests For Submission Of Price Quotations For The Procurement Of The Aforesaid Items Described In The Technical Specifications. The Denr-emb-ncr Intends To Apply The Sum Of Nine Hundred Fifty Thousand And Five Hundred Pesos Only (php 950,500.00) Being The 1 Lotinks And Toners, Rfq No. 2025-fad-002. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. A Set Of Technical Specifications Are Provided In Attachment 1. All Items Listed Under The Purchaser’s Specifications Must Be Complied With On A Pass-fail Basis. Failure To Meet Any One Of The Requirements May Result In Rejection Of The Quotation. Small-value Procurement/shopping Procedures Will Be Conducted In Accordance With The Provisions Of The Implementing Rules And Regulations (irr) Of Republic Act 9184. It Is The Intent Of The Purchaser To Evaluate The Bid/quotation On A Per Item Basis, And Award Will Be Made To The Bid/quotation Or Combination Of Quotations Resulting In The Lowest Evaluated Quotation Meeting The Purchaser’s Technical Specifications. Quotations Must Be Delivered At The Address Below Not Later Than 12:00 P.m. Of February 17 2025. Department Of Environment And Natural Resources Environmental Management Bureau National Capital Region National Ecology Center Compound, East Avenue Diliman, Quezon City Prices Must Be Quoted In Philippine Peso And Must Include The Unit Price And Total Price, Inclusive Of All Taxes To Be Paid And Other Incidental Cost To The Delivery Site/s If The Contract Is Awarded. Bid/quotation May Be Typewritten And May Be Placed In A Sealed Envelope Marked The 1 Lot Inks And Toners, Rfq No. 2025-fad-002. Or You May Send Your Bid- Quotation Through Fax (02-9313134) Or E-mail (emb.bacsec.ncr125@gmail.com). Bids/quotations Shall Be Valid For Sixty (60) Calendar Days From The Deadline Of Submission Of Bids. The Delivery Period Shall Be Within Fifteen (15) Calendar Days From Receipt Of The Purchase Order (p.o) And/or Job Order (j.o). The Supplier Should Inform The Purchaser At Least Three (3) Days Before The Date Of Delivery. The Delivery Will Be Made Only During Working Days And Hours. Delivery Sites: See Delivery Sites Enumerated In The Quotation Form Protect Environment | Protect Life Emb-ncr Building, National Ecology Center Compound, East Ave., Diliman, Quezon City 1100 Telephone No.: (02) 8931-1331 | E-mail: Recordsncr@emb.gov.ph | Ncrsupport@emb.gov.ph Website: Www.ncr.emb.gov.ph Department Of Environment And Natural Resources Environmental Management Bureau National Capital Region National Ecology Center Compound, East Avenue, Diliman, Quezon City The Applicable Rate For Late Deliveries Is One Tenth (1/10) Of One (1) Percent Of The Cost Of The Unperformed Portion Of The Contract For Every Day Of Delay. The Maximum Deduction Shall Be Ten Percent (10%) Of The Amount Of Contract. Once The Cumulative Amount Of Liquidated Damages Reaches Ten Percent (10%) Of The Contract Amount, The Purchaser Shall Rescind The Contract Without Prejudice To Other Courses Of Action And Remedies Open To It. The Purchaser Reserves The Right To Accept Or Reject Any Quotation, And To Annul The Bidding/shopping Process Or Reject All Quotations At Any Time Prior To Contract Award, Without Thereby Incurring Any Liability To The Affected Bidder/bidders. The Purchaser Also Reserves The Right To Waive Minor Deviations/defects Or Infirmities Therein. A Minor Deviation/defect Or Infirmity Is One That Does Not Materially Affect The Overall Functionality Of The Material And The Capability Of The Supplier To Perform The Contract. The Prospective Bidder Shall Submit The Following: Signed Quotation Form Goods- Technical Specifications And Certification From Regulatory Offices, If Applicable (dole Doh And Etc.) Food Services- Menu Civil Works- Plan, Layout, And Design Proof Of Philgeps Registration; Sec Registration/dti Certificate; Business Permit; Tax Clearance Annual Income Tax Return; Preferably With Proof That The Offered Products/items Are Manufactured By An Iso-9001 And Iso14001 Company Whose Certifications Are Valid On Opening Of Proposal; Preferably In Compliance With Philippine Green Public Procurement Roadmap Of Government Procurement Policy Board (gppb); Letter Of Authenticity Of Manufacturer’s Certification That The Supplier Is An Authorized Reseller/distributor And The Items Are Covered By The Manufacturer’s Warranty Failure To Follow The Above Requirements May Result In Outright Rejection Of Submitted Quotation/s. Awarded Bidder Should Sign The Conforme Within Three (3) Working Days Upon Receipt. Failure To Conform Shall Be The Basis In The Consideration Of Appropriate Responsiveness Of The Bidder, In Which The Procuring Entity Shall Proceed To The Next Lowest Calculated And Responsive Bid. Engr. Divina C. Camarao Bac, Chairperson Attachment 1 Technical Specifications No. Purchaser’s Specifications Quantity / Uom Abc Per Unit Total Abc Rfq No. 2025-fad-002 Hp Toner Cf510a, 204a, Black Hp Toner Cf511a, 204a, Cyan Hp Toner Cf512a, 204a, Yellow Hp Toner Cf513a, 204a, Magenta Hp Toner Cf2310a, 215a, Black Hp Toner Cf2311a, 215a, Cyan Hp Toner Cf2312a, 215a, Yellow Hp Toner Cf2313a, 215a, Magenta Hp680 Ink Black Hp680 Ink Tri Color Hp678 Ink Black Hp678 Ink Tri Color Canon Pg 810 Black, Genuine Canon Cl 811 Tri Color, Genuine 30 Cartridge 50 Cartridge 50 Cartridge 50 Cartridge 20 Cartridge 15 Cartridge 15 Cartridge 15 Cartridge 60 Cartridge 50 Cartridge 20 Cartridge 10 Cartridge 30 Cartridge 30 Cartridge ₱950,500.00 ₱950,500.00 Along With Your Signed Quotation Please Submit The Ff: Philgeps Certificate Dti/ Sec Mayor’s Permit Tax Clearance Annual Income Tax Return Preferably With Proof That The Offered Products / Items Are Manufactured By An Iso-9001 And Iso-14001 Company Whose Certifications Are Valid On The Opening On Proposal. Letter Of Authenticity Of Manufacturer’s Certification That The Supplier Is An Authorized Reseller/distributor And The Items Are Covered By The Manufacturer’s Warranty. Quotation Form Date: Rfq No. Attention: Fad-procurement And Property Management Unit Department Of Environment And Natural Resources Environmental Management Bureau-national Capital Region National Ecology Center Compound East Avenue, Diliman, Quezon City 1) Having Examined The Subject Request For Quotation (rfq) Including The Technical Specifications, We, The Undersigned Offer To Supply And Deliver The Following: No. Description Quantity / Uom Deliver Y Site Unit Price (php) Total Price (php) Rfq No. 2025-fad-002 Hp Toner Cf510a, 204a, Black Hp Toner Cf511a, 204a, Cyan Hp Toner Cf512a, 204a, Yellow Hp Toner Cf513a, 204a, Magenta 30 Cartridge 50 Cartridge 50 Cartridge 50 Cartridge Emb- Ncr Hp Toner Cf2310a, 215a, Black 20 Cartridge Hp Toner Cf2311a, 215a, Cyan 15 Cartridge Hp Toner Cf2312a, 215a, Yellow 15 Cartridge Hp Toner Cf2313a, 215a, Magenta 15 Cartridge Hp680 Ink Black 60 Cartridge Hp680 Ink Tri Color 50 Cartridge Hp678 Ink Black 20 Cartridge Hp678 Ink Tri Color 10 Cartridge Canon Pg 810 Black, Genuine 30 Cartridge Canon Cl 811 Tri Color, Genuine 30 Cartridge We Undertake, If Our Quotation Or Bid Is Accepted, To Deliver The Above Goods Within The Fifteen (15)-day Delivery Period From Receipt Purchase Order (p.o) Or Job Order (j.o). We Agree To Abide By This Quotation/bid For A Period Of Sixty (60) Days After The Deadline Of Submission Specified In The Rfq. We Understand That Payment For Items Delivered Will Be Made To The Winning Supplier After The Inspection And Acceptance Of Goods Delivered. Name Of Company : Postal Address : Email Address : Telephone & Fax No. : Supplier’s Representative : Signature Over Printed Name : Account Name And Branch : Preferably Landbank Account. In Case Of Other Banks, Charges May Apply. Omnibus Sworn Statement (revised) [shall Be Submitted With The Bid] Republic Of The Philippines ) City/municipality Of ) S.s. Affidavit I, [name Of Affiant], Of Legal Age, [civil Status], [nationality], And Residing At [address Of Affiant], After Having Been Duly Sworn In Accordance With Law, Do Hereby Depose And State That: [select One, Delete The Other:] [if A Sole Proprietorship:] I Am The Sole Proprietor Or Authorized Representative Of [name Of Bidder] With Office Address At [address Of Bidder]; [if A Partnership, Corporation, Cooperative, Or Joint Venture:] I Am The Duly Authorized And Designated Representative Of [name Of Bidder] With Office Address At [address Of Bidder]; [select One, Delete The Other:] [if A Sole Proprietorship:] As The Owner And Sole Proprietor, Or Authorized Representative Of [name Of Bidder], I Have Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For [name Of The Project] Of The [name Of The Procuring Entity], As Shown In The Attached Duly Notarized Special Power Of Attorney; [if A Partnership, Corporation, Cooperative, Or Joint Venture:] I Am Granted Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For [name Of The Project] Of The [name Of The Procuring Entity], As Shown In The Attached [state Title Of Attached Document Showing Proof Of Authorization (e.g., Duly Notarized Secretary’s Certificate, Board/partnership Resolution, Or Special Power Of Attorney, Whichever Is Applicable;)]; [name Of Bidder] Is Not “blacklisted” Or Barred From Bidding By The Government Of The Philippines Or Any Of Its Agencies, Offices, Corporations, Or Local Government Units, Foreign Government/foreign Or International Financing Institution Whose Blacklisting Rules Have Been Recognized By The Government Procurement Policy Board, By Itself Or By Relation, Membership, Association, Affiliation, Or Controlling Interest With Another Blacklisted Person Or Entity As Defined And Provided For In The Uniform Guidelines On Blacklisting; Each Of The Documents Submitted In Satisfaction Of The Bidding Requirements Is An Authentic Copy Of The Original, Complete, And All Statements And Information Provided Therein Are True And Correct; [name Of Bidder] Is Authorizing The Head Of The Procuring Entity Or Its Duly Authorized Representative(s) To Verify All The Documents Submitted; Consanguinity Or Affinity Up To The Third Civil Degree; [if A Partnership Or Cooperative:] None Of The Officers And Members Of [name Of Bidder] Is Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; [if A Corporation Or Joint Venture:] None Of The Officers, Directors, And Controlling Stockholders Of [name Of Bidder] Is Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; [name Of Bidder] Complies With Existing Labor Laws And Standards; And [name Of Bidder] Is Aware Of And Has Undertaken The Responsibilities As A Bidder In Compliance With The Philippine Bidding Documents, Which Includes: Carefully Examining All Of The Bidding Documents; Acknowledging All Conditions, Local Or Otherwise, Affecting The Implementation Of The Contract; Making An Estimate Of The Facilities Available And Needed For The Contract To Be Bid, If Any; And Inquiring Or Securing Supplemental/bid Bulletin(s) Issued For The [name Of The Project]. [name Of Bidder] Did Not Give Or Pay Directly Or Indirectly, Any Commission, Amount, Fee, Or Any Form Of Consideration, Pecuniary Or Otherwise, To Any Person Or Official, Personnel Or Representative Of The Government In Relation To Any Procurement Project Or Activity. In Case Advance Payment Was Made Or Given, Failure To Perform Or Deliver Any Of The Obligations And Undertakings In The Contract Shall Be Sufficient Grounds To Constitute Criminal Liability For Swindling (estafa) Or The Commission Of Fraud With Unfaithfulness Or Abuse Of Confidence Through Misappropriating Or Converting Any Payment Received By A Person Or Entity Under An Obligation Involving The Duty To Deliver Certain Goods Or Services, To The Prejudice Of The Public And The Government Of The Philippines Pursuant To Article 315 Of Act No. 3815 S. 1930, As Amended, Or The Revised Penal Code. In Witness Whereof, I Have Hereunto Set My Hand This Day Of , 20 At , Philippines. [insert Name Of Bidder Or Its Authorized Representative] [insert Signatory’s Legal Capacity] Affiant [jurat] [format Shall Be Based On The Latest Rules On Notarial] Purchase Request Appendix 60 Department Of Environment & Natural Resources Environmental Management Bureau National Capital Region Fund Cluster: Office/section: Fad-ppmu Pr No.: 2025-01-031 Responsibility Center Code : Date: January 20, 2025 Stock/ Property No. Unit Item Description Quantity Unit Cost Total Cost Cartridge Hp Toner Cf510a, 204a, Black 30 ₱ 3,200.00 ₱96,000.00 Cartridge Hp Toner Cf511a, 204a, Cyan 50 ₱ 3,400.00 ₱170,000.00 Cartridge Hp Toner Cf512a, 204a, Yellow 50 ₱ 3,400.00 ₱170,000.00 Cartridge Hp Toner Cf513a, 204a, Magenta 50 ₱ 3,400.00 ₱170,000.00 Cartridge Hp Toner Cf2310a, 215a, Black 20 ₱ 3,000.00 ₱60,000.00 Cartridge Hp Toner Cf2311a, 215a, Cyan 15 ₱ 3,200.00 ₱48,000.00 Cartridge Hp Toner Cf2312a, 215a, Yellow 15 ₱ 3,200.00 ₱48,000.00 Cartridge Hp Toner Cf2313a, 215a, Magenta 15 ₱ 3,200.00 ₱48,000.00 Cartridge Hp680 Ink Black 60 ₱ 500.00 ₱30,000.00 Cartridge Hp680 Ink Tri Color 50 ₱ 500.00 ₱25,000.00 Cartridge Hp678 Ink Black 20 ₱ 650.00 ₱13,000.00 Cartridge Hp678 Ink Tri Color 10 ₱ 650.00 ₱6,500.00 Cartridge Canon Pg 810 Black, Genuine 30 ₱ 1,000.00 ₱30,000.00 Cartridge Canon Cl 811 Tri Color, Genuine 30 ₱ 1,200.00 ₱36,000.00 Total ₱950,500.00 Charged To Gaa - Regular Fund Code: Funds Available: Christine Joy J. Acaban Unit Head, Budget Purpose: For Official Use Of Emb Ncr Requested By: Approved By: Signature: Printed Name: Gemma G. Carino Engr. Maria Dorica Naz-hipe, Ceso V Designation: Chief,fad Regional Director Date: Purchase Request Appendix 60 Department Of Environment & Natural Resources Environmental Management Bureau National Capital Region Fund Cluster: Office/section: Fad-ppmu Pr No.: 2025-01-031 Responsibility Center Code : Date: January 20, 2025 Stock/ Property No. Unit Item Description Quantity Unit Cost Total Cost Cartridge Hp Toner Cf510a, 204a, Black 30 ₱ 3,200.00 ₱96,000.00 Cartridge Hp Toner Cf511a, 204a, Cyan 50 ₱ 3,400.00 ₱170,000.00 Cartridge Hp Toner Cf512a, 204a, Yellow 50 ₱ 3,400.00 ₱170,000.00 Cartridge Hp Toner Cf513a, 204a, Magenta 50 ₱ 3,400.00 ₱170,000.00 Cartridge Hp Toner Cf2310a, 215a, Black 20 ₱ 3,000.00 ₱60,000.00 Cartridge Hp Toner Cf2311a, 215a, Cyan 15 ₱ 3,200.00 ₱48,000.00 Cartridge Hp Toner Cf2312a, 215a, Yellow 15 ₱ 3,200.00 ₱48,000.00 Cartridge Hp Toner Cf2313a, 215a, Magenta 15 ₱ 3,200.00 ₱48,000.00 Cartridge Hp680 Ink Black 60 ₱ 500.00 ₱30,000.00 Cartridge Hp680 Ink Tri Color 50 ₱ 500.00 ₱25,000.00 Cartridge Hp678 Ink Black 20 ₱ 650.00 ₱13,000.00 Cartridge Hp678 Ink Tri Color 10 ₱ 650.00 ₱6,500.00 Cartridge Canon Pg 810 Black, Genuine 30 ₱ 1,000.00 ₱30,000.00 Cartridge Canon Cl 811 Tri Color, Genuine 30 ₱ 1,200.00 ₱36,000.00 Total ₱950,500.00 Charged To Gaa - Regular Fund Code: Funds Available: Christine Joy J. Acaban Unit Head, Budget Purpose: For Official Use Of Emb Ncr Requested By: Approved By: Signature: Printed Name: Gemma G. Carino Engr. Maria Dorica Naz-hipe, Ceso V Designation: Chief,fad Regional Director Date: Engr. Christian Dale E. Formeloza App-cse 2025 Form - Other Items Annual Procurement Plan - Commom-use Supplies And Equipment (app-cse) 2025 Form - Other Items Agency Code/uacs: Contact Person: Agency Name: Designation: Organization Type: Email: Region: Contact Number: Address: Introduction: Reminders: This Form Shall Be Utilized By Government Agencies For Items That Are Not Available In The Ps-dbm Catalogue But Are Regularly Purchased From Other Sources. Information Given In This Form Will Serve As A Survey To Identify The Items That May Be Considered As Cse By The Ps-dbm. The App-cse 2025 Form - Other Items Must Be Accomplished Using Excel Only. The App-cse Form - Other Items Shall Be Deemed Incorrect Or Invalid If The Form Used Is In Other Than The Prescribed Format Which Can Be Downloaded In The Ps-dbm Website (www.ps-philgeps.gov.ph). All Information Must Be Provided Accurately. To Fill-out, Find The Item In The 'list Of Items - 1' Tab Of This File Then Type The Desired Product In The Search Bar (working Only For Mirosoft Excel 2013 Or Higher). Copy The Description, Right Click Then Paste As Values In The Dedicated Column Of The Form 'item Description". You May Also Use The 'list Of Items - 2' Then Press Ctrl + F To Find The Item. If It Is Necessary To Input The Details Of The Product, You May Type It In The 'specification' Column Provided Beside The Item Description.the First One Hundred (100) Rows Are Dedicated Only For This Procedure, While The Remaining Rows Is Open For Editing. You Can Insert Additional Rows After The First 100 If Necessary. Upload The App-cse 2025 Form - Other Items Through The Google Forms Link: Https://shorturl.at/adeqo For Further Assistance Or Clarification, Agencies May Contact The Marketing And Sales Division Of Ps-dbm Through Its Mobile Numbers 0918-2954426 (smart) Or 0962-8255199 (smart), Or Email Appcse.helpdesk@ps- Philgeps.gov.ph, Or Visit The Ps-dbm Website (www.ps-philgeps.gov.ph) For The Guide On How To Fill-out The App-cse The App-cse For Fy 2025 Must Be Submitted On Or Before July 31, 2024 No. Unspsc Item Description Specification (input Specific Features Or Composition Of The Item Such As Dimensions, Color, Or Functions) Unit Of Measure Monthly Quantity Requirement Total Quantity For The Year Price Total Amount For The Year Jan Feb Mar Q1 Q1 Amount April May June Q2 Q2 Amount July Aug Sept Q3 Q3 Amount Oct Nov Dec Q4 Q4 Amount Other Items Not Available At Ps-dbm But Are Regularly Purchased From Other Sources (note: Please Indicate Price Of Items) 1 - Ink Cartridge, Canon Pg-810 Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 990.00 0.00 2 - Ink Cartridge, Canon Cl-811 Tri-color Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,300.00 0.00 3 - Toner Cartridge, Canon 054h, 3028c001 Black Cart 1 0 1 2 13,000.00 0 1 0 1 6,500.00 1 1 0 2 13,000.00 0 0 0 0 0.00 5 6,500.00 32,500.00 4 - Toner Cartridge, Canon 054h, 3025c001 Yellow Cart 0 1 0 1 6,500.00 0 1 0 1 6,500.00 0 1 0 1 6,500.00 0 1 0 1 6,500.00 4 6,500.00 26,000.00 5 - Toner Cartridge, Canon 054h, 3026c001 Magenta Cart 0 1 0 1 6,500.00 0 1 0 1 6,500.00 0 1 0 1 6,500.00 0 1 0 1 6,500.00 4 6,500.00 26,000.00 6 - Toner Cartridge, Canon 054h, 3027c001 Cyan Cart 0 1 0 1 6,500.00 0 1 0 1 6,500.00 0 1 0 1 6,500.00 0 1 0 1 6,500.00 4 6,500.00 26,000.00 7 - Ink Bottle, Hp Gt53, 1vv22aa Black Bottle 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 8 - Ink Bottle, Hp Gt52, M0h54aa Cyan Bottle 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 9 - Ink Bottle, Hp Gt52, M0h55aa Magenta Bottle 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 10 - Ink Bottle, Hp Gt52, M0h56aa Yellow Bottle 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 11 - Toner Cartridge, Hp 202a, Cf500a Black Cart 2 2 1 5 21,000.00 2 2 1 5 21,000.00 2 2 1 5 21,000.00 2 2 1 5 21,000.00 20 4,200.00 84,000.00 12 - Toner Cartridge, Hp 202a, Cf501a Cyan Cart 2 2 1 5 25,000.00 2 2 1 5 25,000.00 2 2 1 5 25,000.00 2 2 1 5 25,000.00 20 5,000.00 100,000.00 13 - Toner Cartridge, Hp 202a, Cf502a Yellow Cart 2 2 1 5 25,000.00 2 2 1 5 25,000.00 2 2 1 5 25,000.00 2 2 1 5 25,000.00 20 5,000.00 100,000.00 14 - Toner Cartridge, Hp 202a, Cf503a Magenta Cart 2 2 1 5 25,000.00 2 2 1 5 25,000.00 2 2 1 5 25,000.00 2 2 1 5 25,000.00 20 5,000.00 100,000.00 15 - Toner Cartridge, Hp 204a, Cf510a Black Cart 10 10 10 30 96,000.00 10 10 10 30 96,000.00 5 5 5 15 48,000.00 5 5 5 15 48,000.00 90 3,200.00 288,000.00 16 - Toner Cartridge, Hp204a, Cf511a Cyan Cart 5 5 5 15 53,250.00 5 5 5 15 53,250.00 5 5 5 15 53,250.00 5 5 5 15 53,250.00 60 3,550.00 213,000.00 17 - Toner Cartridge, Hp204a, Cf512a Yellow Cart 5 5 5 15 53,250.00 5 5 5 15 53,250.00 5 5 5 15 53,250.00 5 5 5 15 53,250.00 60 3,550.00 213,000.00 18 - Toner Cartridge, Hp204a, Cf513a Magenta Cart 5 5 5 15 53,250.00 5 5 5 15 53,250.00 5 5 5 15 53,250.00 5 5 5 15 53,250.00 60 3,550.00 213,000.00 19 - Toner Cartridge, Hp 107a, W1107a Black Cart 0 5 5 10 25,000.00 0 5 5 10 25,000.00 0 5 5 10 25,000.00 0 5 5 10 25,000.00 40 2,500.00 100,000.00 20 - Toner Cartridge, Hp 85a, Ce285a Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 21 - Toner Cartridge, Hp 79a, Cf279a Black Cart 5 0 5 10 39,750.00 0 0 0 0 0.00 5 0 5 10 39,750.00 0 0 0 0 0.00 20 3,975.00 79,500.00 22 - Toner Cartridge, Hp 215a, W2310a Black Cart 5 5 2 12 37,200.00 5 5 2 12 37,200.00 5 5 2 12 37,200.00 5 5 2 12 37,200.00 48 3,100.00 148,800.00 23 - Toner Cartridge, Hp215a, W2311a Cyan Cart 5 5 2 12 39,600.00 5 5 2 12 39,600.00 5 5 2 12 39,600.00 5 5 2 12 39,600.00 48 3,300.00 158,400.00 24 - Toner Cartridge, Hp215a, W2312a Yellow Cart 5 5 2 12 39,600.00 5 5 2 12 39,600.00 5 5 2 12 39,600.00 5 5 2 12 39,600.00 48 3,300.00 158,400.00 25 - Toner Cartridge, Hp215a, W2313a Magenta Cart 5 5 2 12 39,600.00 5 5 2 12 39,600.00 5 5 2 12 39,600.00 5 5 2 12 39,600.00 48 3,300.00 158,400.00 26 - Ink Cartridge, Hp 678, Hpcz107aa Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 600.00 0.00 27 - Ink Cartridge, Hp 678, Hpcz108aa Tri-color Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 600.00 0.00 28 - Ink Cartridge, Hp 680, F6v27aa Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 600.00 0.00 29 - Ink Cartridge, Hp 680, F6v26aa Tri-color Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 600.00 0.00 30 - Ink Cartridge, Hp 955, L0s60aa Black Cart 1 1 1 3 4,200.00 1 1 1 3 4,200.00 1 1 1 3 4,200.00 1 1 1 3 4,200.00 12 1,400.00 16,800.00 31 - Ink Cartridge, Hp 955, L0s51aa Cyan Cart 1 1 1 3 3,300.00 1 1 1 3 3,300.00 1 1 1 3 3,300.00 1 1 1 3 3,300.00 12 1,100.00 13,200.00 32 - Ink Cartridge, Hp 955, L0s57aa Yellow Cart 1 1 1 3 3,300.00 1 1 1 3 3,300.00 1 1 1 3 3,300.00 1 1 1 3 3,300.00 12 1,100.00 13,200.00 33 - Ink Cartridge, Hp 955, L0s54aa Magenta Cart 1 1 1 3 3,300.00 1 1 1 3 3,300.00 1 1 1 3 3,300.00 1 1 1 3 3,300.00 12 1,100.00 13,200.00 34 - Toner, Epson Wf-c5790 (black, Cyan, Yellow, Magenta) Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 15,000.00 0.00 35 - Ink Cartridge, Epson T289 Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 36 - Ink Cartridge, Epson T290 Tri-color Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 37 - Ink Bottle, Epson 003, T00v100 Black Bottle 5 5 5 15 3,000.00 5 5 5 15 3,000.00 5 5 5 15 3,000.00 5 5 5 15 3,000.00 60 200.00 12,000.00 38 - Ink Bottle, Epson 003, T00v200 Cyan Bottle 5 0 5 10 2,000.00 5 0 5 10 2,000.00 5 0 5 10 2,000.00 5 0 5 10 2,000.00 40 200.00 8,000.00 39 - Ink Bottle, Epson 003, T00v300 Magenta Bottle 5 0 5 10 2,000.00 5 0 5 10 2,000.00 5 0 5 10 2,000.00 5 0 5 10 2,000.00 40 200.00 8,000.00 40 - Ink Bottle, Epson 003, T00v400 Yellow Bottle 5 0 5 10 2,000.00 5 0 5 10 2,000.00 5 0 5 10 2,000.00 5 0 5 10 2,000.00 40 200.00 8,000.00 41 - Ink Bottle, Epson 001, C13t03y100 Black Bottle 0 0 1 1 600.00 0 0 1 1 600.00 0 0 1 1 600.00 0 1 1 2 1,200.00 5 600.00 3,000.00 42 - Ink Bottle, Epson 001, C13t03y200 Cyan Bottle 0 0 1 1 400.00 0 0 1 1 400.00 0 0 1 1 400.00 0 1 1 2 800.00 5 400.00 2,000.00 43 - Ink Bottle, Epson 001, C13t03y300 Magenta Bottle 0 0 1 1 400.00 0 0 1 1 400.00 0 0 1 1 400.00 0 1 1 2 800.00 5 400.00 2,000.00 44 - Ink Bottle, Epson 001, C13t03y400 Yellow Bottle 0 0 1 1 400.00 0 0 1 1 400.00 0 0 1 1 400.00 0 1 1 2 800.00 5 400.00 2,000.00 45 - Ink Bottle, Epson 005, T03q100 Black Bottle 1 1 1 3 2,400.00 1 1 1 3 2,400.00 1 1 1 3 2,400.00 1 1 1 3 2,400.00 12 800.00 9,600.00 46 - Ink Bottle, Epson 664, C13t664100 Black Bottle 0 0 5 5 2,000.00 0 0 10 10 4,000.00 0 0 5 5 2,000.00 0 0 10 10 4,000.00 30 400.00 12,000.00 47 - Ink Bottle, Epson 664, C13t664200 Cyan Bottle 0 0 5 5 2,000.00 0 0 5 5 2,000.00 0 0 5 5 2,000.00 0 0 5 5 2,000.00 20 400.00 8,000.00 48 - Ink Bottle, Epson 664, C13t664300 Magenta Bottle 0 0 5 5 2,000.00 0 0 5 5 2,000.00 0 0 5 5 2,000.00 0 0 5 5 2,000.00 20 400.00 8,000.00 49 - Ink Bottle, Epson 664, C13t664400 Yellow Bottle 0 0 5 5 2,000.00 0 0 5 5 2,000.00 0 0 5 5 2,000.00 0 0 5 5 2,000.00 20 400.00 8,000.00 No. Unspsc Item Description Specification (input Specific Features Or Composition Of The Item Such As Dimensions, Color, Or Functions) Unit Of Measure Monthly Quantity Requirement Total Quantity For The Year Price Total Amount For The Year Jan Feb Mar Q1 Q1 Amount April May June Q2 Q2 Amount July Aug Sept Q3 Q3 Amount Oct Nov Dec Q4 Q4 Amount Other Items Not Available At Ps-dbm But Are Regularly Purchased From Other Sources (note: Please Indicate Price Of Items) 50 - Ink Bottle, Epson 673, T6731 Black Bottle 0 0 0 0 0.00 1 0 0 1 0.00 0 0 0 0 0.00 1 0 0 1 0.00 2 0.00 0.00 51 - Ink Bottle, Epson 673, T6732 Cyan Bottle 0 0 0 0 0.00 1 0 0 1 0.00 0 0 0 0 0.00 1 0 0 1 0.00 2 0.00 0.00 52 - Ink Bottle, Epson 673, T6733 Magenta Bottle 0 0 0 0 0.00 1 0 0 1 0.00 0 0 0 0 0.00 1 0 0 1 0.00 2 0.00 0.00 53 - Ink Bottle, Epson 673, T6734 Yellow Bottle 0 0 0 0 0.00 1 0 0 1 0.00 0 0 0 0 0.00 1 0 0 1 0.00 2 0.00 0.00 54 - Ink Bottle, Epson 673, T6735 Light Cyan Bottle 0 0 0 0 0.00 1 0 0 1 0.00 0 0 0 0 0.00 1 0 0 1 0.00 2 0.00 0.00 55 - Ink Bottle, Epson 673, T6736 Light Magenta Bottle 0 0 0 0 0.00 1 0 0 1 0.00 0 0 0 0 0.00 1 0 0 1 0.00 2 0.00 0.00 56 - Ribbon Cartridge, Epson Lx310, S015632 Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 57 - Ribbon Cartridge, Epson Lq2190, S015531/s015086 Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 58 - Toner Cartridge, Lexmark Network Printer, 58d3h00 Black Cart 0 0 3 3 54,000.00 0 0 0 0 0.00 0 0 3 3 54,000.00 0 0 0 0 0.00 6 18,000.00 108,000.00 59 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 60 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 61 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 62 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 63 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 64 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 65 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 66 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 67 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 68 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 69 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 70 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 71 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 72 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 73 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 74 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 75 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 76 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 77 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 78 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 79 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 80 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 81 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 82 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 83 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 84 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 85 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 86 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 87 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 88 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 89 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 90 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 91 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 92 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 93 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 94 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 95 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 96 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 97 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 98 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 99 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 100 - 0 0.00 0 0.00 0 0.00 0 0.00 0 0.00 0.00 No. Unspsc Item Description Specification (input Specific Features Or Composition Of The Item Such As Dimensions, Color, Or Functions) Unit Of Measure Monthly Quantity Requirement Total Quantity For The Year Price Total Amount For The Year Jan Feb Mar Q1 Q1 Amount April May June Q2 Q2 Amount July Aug Sept Q3 Q3 Amount Oct Nov Dec Q4 Q4 Amount Other Items Not Available At Ps-dbm But Are Regularly Purchased From Other Sources (note: Please Indicate Price Of Items) A. Total ₱ 2,480,000.00 B. Additional Provision For Inflation (10% Of Total) ₱ 248,000.00 C. Additional Provision For Transport And Freight Cost (if Applicable) ₱ - D. Grand Total (a + B+ C) ₱ 2,728,000.00 E. Approved Budget By The Agency Head In Figures And Words: We Hereby Warrant That The Total Amount Reflected In This Annual Procurement Plan To Procure The Listed Common-use Supplies, Materials, And Equipment Has Been Included In Or Is Within Our Approved Budget For The Year. Prepared By: Certified Funds Available / Certified Appropriate Funds Available: Approved By: Jodi Hani C. Leal / Cesar D. Tolentino Property/supply Officer Accountant / Budget Officer Date Prepared: Introduction: App-cse 2025 Form Annual Procurement Plan - Commom-use Supplies And Equipment (app-cse) 2025 Form This Form Contains The Common-use Supplies And Equipment (cse) Being Carried By The Procurement Service – Department Of Budget And Management (ps-dbm) That Shall Be Purchased By Government Agencies. Consistent With The Dbm Circular Letter Nos. 2011-6 And 2011-6-a Dated 25 August 2011 And 28 September 2011, Respectively, The App-cse Shall Serve As The Agency’s Annual Procurement Request For All Its Cse Requirements. Only Agencies With Uploaded App-cse In The Modernized Philippine Government Electronic Procurement System (mphilgeps) Will Be Able To Purchase Cse From The Ps-dbm. Note That The Items Listed On This Form Have Been Arranged In Accordance With The United Nations Standard Products And Services Code (unspsc). Reminders: 1.0 2.0 3.0 The App-cse Form Must Be Accomplished Using Microsoft Excel Format. The App-cse Shall Be Deemed Incorrect Or Invalid If The Form Used Is Other Than The Prescribed Format Which Is Downloadable From The Mphilgeps And Downloads Page Of Ps-dbm Website (www.ps-philgeps.gov.ph). All Information Must Be Provided Accurately. Kindly Refer To The Cse Catalogue On The Ps-dbm Website (www.ps-philgeps.gov.ph) Under The "what We Sell" Tab For The Detailed Technical Specifications And Sample Photo Of The Items. 4.0 Do Not Delete, Add, Or Revise Any Items Or Rows On This Form, Otherwise The Form Will Be Deemed Invalid. 5.0 6.0 7.0 8.0 For Items Not Included On The List Of Part Ii, A Separate File, With The File Name App-cse 2025 Form - Other Items, Can Be Downloaded From The Downloads Page Of Ps-dbm Website (www.ps-philgeps.gov.ph) And Must Be Submitted To Ps-dbm Through This Link: Https://shorturl.at/adeqo. Instructions On How To Fill-out Is Included In The Reminders Of The Form. Once Signed And Approved By The Property/supply Officer, Accountant/budget Officer, And Head Of The Agency/office, Kindly Upload The Soft Copy Of The App-cse In Microsoft Excel Format As Well As The Original Signed Copy In Portable Document Format (pdf) To The Agency's Mphilgeps Account On Or Before The Prescribed Period Or Deadline. Any App-cse Form That Is Unsigned Or Has Incomplete Signature Shall Be Deemed Invalid. Should There Be Changes In The Agency’s Cse Requirements, The Agency May Edit Their Uploaded App-cse Directly On Their Mphilgeps Account. However, The Agency Must Ensure That A Signed And Approved Copy Of The Supplemental App-cse Form Is Available. Note That All Cse Requirements In Excess Of The Quantities Indicated In The Original App-cse Form Will Not Be Served If Not Covered By A Supplemental App-cse. For Further Assistance Or Clarification, Agencies May Contact The Marketing And Sales Division Of Ps-dbm Through Its Mobile Numbers 0918-2954426 (smart) Or 0962-8255199 (smart), Or Email Appcse.helpdesk@ps-philgeps.gov.ph, Or Visit The Ps-dbm Website (www.ps-philgeps.gov.ph) For The Guide On How To Fill-out The App-cse. Environmental Management B Ncr Nec Cmpd., East Ave., Brgy. Central, Quezon City Joy Anne Marie A. Mancera Head, Ppmu Ppmudivision03@gmail.com 8931-13-31 Note: The App-cse For Fy 2025 Must Be Submitted On Or Before 31 July 2024. Department/bureau/office: Agency Code/uacs: Contact Person: Region: Organization Type: Position: Address: E-mail : Telephone/mobile Nos: Item & Specifications Unit Of Measure Monthly Quantity Requirement Total Quantity For The Year Price Total Amount For The Year Jan Feb Mar Q1 Q1 Amount April May June Q2 Q2 Amount July Aug Sept Q3 Q3 Amount Oct Nov Dec Q4 Q4 Amount Part I. Available At Ps-dbm (main Warehouse And Depots) Alcohol Or Acetone Based Antiseptics 1 12191601-al-e04 Alcohol, Ethyl, 500 Ml Bottle 0 0 0 0 0.00 70 70 70 210 10,590.30 0 0 0 0 0.00 70 70 70 210 10,590.30 420 50.43 21,180.60 2 12191601-al-e03 Alcohol, Ethyl, 1 Gallon Gallon 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 357.09 0.00 Arts And Crafts Equipment And Accessories And Supplies 3 60121413-cb-p01 Clearbook, A4 Size Piece 0 12 0 12 421.92 0 12 0 12 421.92 0 12 0 12 421.92 0 12 0 12 421.92 48 35.16 1,687.68 4 60121413-cb-p02 Clearbook, Legal Size Piece 0 12 0 12 436.32 0 12 0 12 436.32 0 12 0 12 436.32 0 12 0 12 436.32 48 36.36 1,745.28 5 60121534-er-p01 Eraser, Plastic/rubber Piece 0 10 0 10 82.60 0 10 0 10 82.60 0 10 0 10 82.60 0 10 0 10 82.60 40 8.26 330.40 6 60121524-sp-g01 Sign Pen, Extra Fine Tip, Black Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 22.20 0.00 7 60121524-sp-g04 Sign Pen, Fine Tip, Black Piece 30 30 30 90 4,024.80 30 30 30 90 4,024.80 30 30 30 90 4,024.80 30 30 30 90 4,024.80 360 44.72 16,099.20 8 60121524-sp-g07 Sign Pen, Medium Tip, Black Piece 30 30 30 90 5,148.00 30 30 30 90 5,148.00 30 30 30 90 5,148.00 30 30 30 90 5,148.00 360 57.20 20,592.00 9 60121524-sp-g02 Sign Pen, Extra Fine Tip, Blue Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 22.20 0.00 10 60121524-sp-g05 Sign Pen, Fine Tip, Blue Piece 50 50 50 150 6,708.00 50 50 50 150 6,708.00 50 50 50 150 6,708.00 50 50 50 150 6,708.00 600 44.72 26,832.00 11 60121524-sp-g08 Sign Pen, Medium Tip, Blue Piece 80 80 80 240 13,728.00 80 80 80 240 13,728.00 80 80 80 240 13,728.00 80 80 80 240 13,728.00 960 57.20 54,912.00 12 60121524-sp-g03 Sign Pen, Extra Fine Tip, Red Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 22.20 0.00 13 60121524-sp-g06 Sign Pen, Fine Tip, Red Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 45.76 0.00 14 60121524-sp-g09 Sign Pen, Medium Tip, Red Piece 12 12 12 36 2,059.20 12 12 12 36 2,059.20 12 12 12 36 2,059.20 12 12 12 36 2,059.20 144 57.20 8,236.80 15 60121124-wr-p01 Wrapping Paper Pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 161.20 0.00 Audio And Visual Equipment And Supplies 16 45121517-do-c03 Document Camera Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 23,623.60 0.00 17 45111609-mm-p01 Multimedia Projector Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 16,588.00 0.00 Batteries And Cells And Accessories 18 26111702-bt-a02 Battery, Dry Cell, Size Aa Pack 100 100 100 300 6,147.00 100 100 100 300 6,147.00 100 100 100 300 6,147.00 100 100 100 300 6,147.00 1200 20.49 24,588.00 19 26111702-bt-a01 Battery, Dry Cell, Size Aaa Pack 100 100 100 300 5,502.00 100 100 100 300 5,502.00 100 100 100 300 5,502.00 100 100 100 300 5,502.00 1200 18.34 22,008.00 Cleaning Equipment And Supplies 20 47131812-af-a01 Air Freshener Can 12 12 12 36 3,143.16 12 12 12 36 3,143.16 12 12 12 36 3,143.16 12 12 12 36 3,143.16 144 87.31 12,572.64 21 47131604-br-s01 Broom (walis Tambo) Piece 8 8 8 24 2,995.20 8 8 8 24 2,995.20 8 8 8 24 2,995.20 8 8 8 24 2,995.20 96 124.80 11,980.80 22 47131604-br-t01 Broom (walis Ting-ting) Piece 12 12 12 36 936.00 12 12 12 36 936.00 12 12 12 36 936.00 12 12 12 36 936.00 144 26.00 3,744.00 23 47131829-tb-c01 Cleaner, Toilet Bowl And Urinal Bottle 10 10 10 30 1,248.00 10 10 10 30 1,248.00 10 10 10 30 1,248.00 10 10 10 30 1,248.00 120 41.60 4,992.00 24 47131805-cl-p01 Cleanser, Scouring Powder Plastic Container 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 23.92 0.00 Item & Specifications Unit Of Measure Monthly Quantity Requirement Total Quantity For The Year Price Total Amount For The Year Jan Feb Mar Q1 Q1 Amount April May June Q2 Q2 Amount July Aug Sept Q3 Q3 Amount Oct Nov Dec Q4 Q4 Amount 25 47131811-de-b02 Detergent Bar Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 9.34 0.00 26 47131811-de-p02 Detergent Powder, All Purpose Pouch 35 35 35 105 5,678.40 35 35 35 105 5,678.40 35 35 35 105 5,678.40 35 35 35 105 5,678.40 420 54.08 22,713.60 27 47131803-ds-a01 Disinfectant Spray Can 12 12 12 36 5,036.04 12 12 12 36 5,036.04 12 12 12 36 5,036.04 12 12 12 36 5,036.04 144 139.89 20,144.16 28 47131601-du-p01 Dust Pan Piece 0 0 10 10 468.00 0 0 10 10 468.00 0 0 10 10 468.00 0 0 10 10 468.00 40 46.80 1,872.00 29 47131802-fw-p03 Floor Wax, Paste Type, Red Can 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 309.76 0.00 30 47131830-fc-a01 Furniture Cleaner Can 4 4 4 12 1,696.68 4 4 4 12 1,696.68 4 4 4 12 1,696.68 4 4 4 12 1,696.68 48 141.39 6,786.72 31 73101612-hs-l01 Hand Soap, Liquid, 500ml Bottle 40 40 40 120 5,154.00 40 40 40 120 5,154.00 40 40 40 120 5,154.00 40 40 40 120 5,154.00 480 42.95 20,616.00 32 47121804-mp-b01 Mop Bucket Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 2,288.00 0.00 33 47131501-rg-c01 Rags Kilo 0 0 0 0 0.00 0 0 0 0 0.00 0 12 0 12 833.64 0 12 0 12 833.64 24 69.47 1,667.28 34 47131602-sc-n01 Scouring Pad Pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 85.63 0.00 35 47121701-tb-p04 Trashbag, Xxl Size Roll/pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 130.00 0.00 36 47121701-tb-p05 Trashbag, Large Size Roll/pack 50 50 50 150 8,892.00 50 50 50 150 8,892.00 50 50 50 150 8,892.00 50 50 50 150 8,892.00 600 59.28 35,568.00 37 47121701-tb-p06 Trashbag, Xl Size Roll/pack 50 50 50 150 13,884.00 50 50 50 150 13,884.00 50 50 50 150 13,884.00 50 50 50 150 13,884.00 600 92.56 55,536.00 38 47121702-wb-p01 Wastebasket Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 43.68 0.00 Color Compounds And Dispersions 39 12171703-si-p01 Ink, For Stamp Pad Bottle 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 28.79 0.00 Consumer Electronics 40 52161535-dv-r02 Digital Voice Recorder Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 7,339.16 0.00 Films 41 13111203-ac-f01 Acetate Roll 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,243.84 0.00 42 13111201-cf-p02 Carbon Film, Legal Size Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 351.83 0.00 Fire Fighting Equipment 43 46191601-fe-m01 Fire Extinguisher, Dry Chemical Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,144.00 0.00 Flag Or Accessories 44 55121905-ph-f01 Philippine National Flag Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 1 0 1 284.84 0 0 0 0 0.00 1 284.84 284.84 Furniture And Furnishings 45 56101504-cm-b01 Monobloc Chair, Beige Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 341.12 0.00 46 56101504-cm-w01 Monobloc Chair, White Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 341.12 0.00 Heating And Ventilation And Air Circulation 47 40101604-ef-c01 Electric Fan, Ceiling Mount, Orbit Type Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,222.00 0.00 48 40101604-ef-g01 Electric Fan, Industrial, Ground Type Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,109.68 0.00 49 40101604-ef-s01 Electric Fan, Stand Type Unit 0 0 1 1 1,560.00 0 0 1 1 1,560.00 0 0 1 1 1,560.00 0 0 1 1 1,560.00 4 1,560.00 6,240.00 50 40101604-ef-w01 Electric Fan, Wall Mount Unit 0 0 1 1 901.68 0 0 1 1 901.68 0 0 1 1 901.68 0 0 1 1 901.68 4 901.68 3,606.72 Information And Communication Technology (ict) Equipment And Devices And Accessories 51 43211507-dsk003 Desktop, For Basic Users Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 24,793.60 0.00 52 43211507-dsk004 Desktop, For Mid-range Users Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 42,390.40 0.00 53 43201827-hd-x02 External Hard Drive Unit 5 0 5 10 30,149.60 5 0 5 10 30,149.60 5 0 5 10 30,149.60 5 0 5 10 30,149.60 40 3,014.96 120,598.40 54 43202010-fd-u04 Flash Drive Piece 5 5 5 15 2,291.10 5 5 5 15 2,291.10 5 5 5 15 2,291.10 5 5 5 15 2,291.10 60 152.74 9,164.40 55 43211503-lap004 Laptop Computer, For Mid-range Users Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 42,380.00 0.00 56 43211503-lap003 Laptop Computer, Lightweight Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 46,800.00 0.00 57 43211708-mo-o02 Computer Mouse, Wireless Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 161.92 0.00 58 43212105-pr-l01 Printer, Laser, Monochrome Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 2,636.89 0.00 Lighting And Fixtures And Accessories 59 39101628-lb-l01 Light-emitting Diode (led) Light Bulb, 7 Watts Piece 12 12 12 36 2,721.96 12 12 12 36 2,721.96 12 12 12 36 2,721.96 12 12 12 36 2,721.96 144 75.61 10,887.84 60 39101628-lt-l01 Light-emitting Diode (led) Linear Tube, 18 Watts Piece 30 30 30 90 18,523.80 30 30 30 90 18,523.80 30 30 30 90 18,523.80 30 30 30 90 18,523.80 360 205.82 74,095.20 Manufacturing Components And Supplies 61 31201610-gl-j02 Glue, All-purpose Bottle 0 0 10 10 621.40 0 0 10 10 621.40 0 0 10 10 621.40 0 0 10 10 621.40 40 62.14 2,485.60 62 31151804-sw-h01 Staple Wire, Heavy Duty (binder Type), 23/13 Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 36.40 0.00 63 31151804-sw-s01 Staple Wire, Standard Box 10 10 10 30 712.80 10 10 10 30 712.80 10 10 10 30 712.80 10 10 10 30 712.80 120 23.76 2,851.20 Item & Specifications Unit Of Measure Monthly Quantity Requirement Total Quantity For The Year Price Total Amount For The Year Jan Feb Mar Q1 Q1 Amount April May June Q2 Q2 Amount July Aug Sept Q3 Q3 Amount Oct Nov Dec Q4 Q4 Amount 64 31201502-ta-e02 Tape, Electrical Roll 0 0 20 20 389.00 0 0 20 20 389.00 0 0 20 20 389.00 0 0 20 20 389.00 80 19.45 1,556.00 65 31201503-ta-m01 Tape, Masking, 24mm Roll 30 30 30 90 5,011.20 30 30 30 90 5,011.20 30 30 30 90 5,011.20 30 30 30 90 5,011.20 360 55.68 20,044.80 66 31201503-ta-m02 Tape, Masking, 48 Mm Roll 50 50 50 150 18,174.00 50 50 50 150 18,174.00 50 50 50 150 18,174.00 50 50 50 150 18,174.00 600 121.16 72,696.00 67 31201517-ta-p01 Tape, Packaging, 48 Mm Roll 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 22.36 0.00 68 31201512-ta-t01 Tape, Transparent, 24mm Roll 0 0 30 30 530.40 0 0 30 30 530.40 0 0 30 30 530.40 0 0 30 30 530.40 120 17.68 2,121.60 69 31201512-ta-t02 Tape, Transparent, 48 Mm Roll 0 0 30 30 677.10 0 0 30 30 677.10 0 0 30 30 677.10 0 0 30 30 677.10 120 22.57 2,708.40 70 31151507-tw-p01 Twine, Plastic Roll 0 0 10 10 666.20 0 0 0 0 0.00 0 0 10 10 666.20 0 0 0 0 0.00 20 66.62 1,332.40 Measuring And Observing And Testing Equipment 71 41111604-ru-p02 Ruler, Plastic, 450mm Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 19.93 0.00 Office Equipment And Accessories And Supplies 72 44121612-bl-h01 Blade, For General Purpose Cutter/utility Knife Tube 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 16.37 0.00 73 44101602-pb-m01 Binding And Punching Machine Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 9,534.72 0.00 74 44122037-rb-p10 Binding Ring/comb, Plastic, 32 Mm Bundle 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 259.89 0.00 75 44101807-ca-c01 Calculator, Compact Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 235.77 0.00 76 44121710-ch-w01 Chalk, White Enamel Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 32.97 0.00 77 44122105-bf-c01 Clip, Backfold, 19mm Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 9.36 0.00 78 44122105-bf-c02 Clip, Backfold, 25mm Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 15.60 0.00 79 44122105-bf-c03 Clip, Backfold, 32mm Box 12 12 12 36 1,198.08 12 12 12 36 1,198.08 12 12 12 36 1,198.08 12 12 12 36 1,198.08 144 33.28 4,792.32 80 44122105-bf-c04 Clip, Backfold, 50mm Box 12 12 12 36 2,171.52 12 12 12 36 2,171.52 12 12 12 36 2,171.52 12 12 12 36 2,171.52 144 60.32 8,686.08 81 44121801-ct-r02 Correction Tape Piece 40 40 40 120 1,620.00 40 40 40 120 1,620.00 40 40 40 120 1,620.00 40 40 40 120 1,620.00 480 13.50 6,480.00 82 44121612-cu-h01 Cutter/utility Knife, For General Purpose Piece 0 0 5 5 158.60 0 0 5 5 158.60 0 0 5 5 158.60 0 0 5 5 158.60 20 31.72 634.40 83 44111515-df-b01 Data File Box Piece 0 0 10 10 1,458.90 0 0 10 10 1,458.90 0 0 10 10 1,458.90 0 0 10 10 1,458.90 40 145.89 5,835.60 84 44122011-df-f01 Data Folder Piece 50 50 50 150 12,451.50 50 50 50 150 12,451.50 50 50 50 150 12,451.50 50 50 50 150 12,451.50 600 83.01 49,806.00 85 44103202-ds-m01 Dater Stamp Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 434.95 0.00 86 44121506-en-d01 Envelope, Documentary, A4 Box 0 0 0 0 0.00 0 0 5 5 4,149.60 0 0 5 5 4,149.60 0 0 5 5 4,149.60 15 829.92 12,448.80 87 44121506-en-d02 Envelope, Documentary, Legal, Box 5 0 5 10 10,575.80 5 0 5 10 10,575.80 5 0 5 10 10,575.80 5 0 5 10 10,575.80 40 1,057.58 42,303.20 88 44121506-en-x01 Envelope, Expanding, Kraft Box 5 0 5 10 9,399.50 5 0 5 10 9,399.50 5 0 5 10 9,399.50 5 0 5 10 9,399.50 40 939.95 37,598.00 89 44121506-en-x02 Envelope, Expanding, Plastic Piece 0 0 0 0 0.00 0 0 10 10 304.90 0 0 10 10 304.90 0 0 10 10 304.90 30 30.49 914.70 90 44121506-en-m02 Envelope, Mailing Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 432.52 0.00 91 44121504-en-w02 Envelope, Mailing, With Window Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 512.72 0.00 92 44111912-er-b01 Eraser, Felt, For Blackboard/whiteboard Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 14.48 0.00 93 44122118-fa-p01 Fastener Box 30 30 30 90 8,517.60 30 30 30 90 8,517.60 30 30 30 90 8,517.60 30 30 30 90 8,517.60 360 94.64 34,070.40 94 44111515-fo-x01 File Organizer, Expanding, Plastic, Legal Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 90.20 0.00 95 44122018-ft-d01 File Tab Divider, A4 Set 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 11.13 0.00 96 44122018-ft-d02 File Tab Divider, Legal Set 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 14.23 0.00 97 44122011-fo-f01 Folder, Fancy With Slide, A4 Bundle 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 270.40 0.00 98 44122011-fo-f02 Folder, Fancy With Slide, Legal Bundle 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 291.20 0.00 99 44122011-fo-l01 Folder, L-type, A4 Pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 200.28 0.00 100 44122011-fo-l02 Folder, L-type, Legal Pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 249.08 0.00 101 44122027-fo-p01 Folder, Pressboard Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 952.64 0.00 102 44122011-fo-t01 Folder With Tab, A4 Pack 0 0 5 5 1,898.00 0 0 5 5 1,898.00 0 0 5 5 1,898.00 0 0 5 5 1,898.00 20 379.60 7,592.00 103 44122011-fo-t02 Folder With Tab, Legal Pack 0 0 10 10 4,139.20 0 0 10 10 4,139.20 0 0 10 10 4,139.20 0 0 10 10 4,139.20 40 413.92 16,556.80 104 44122008-it-t01 Index Tab Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 67.60 0.00 105 44121716-ma-f01 Marker, Flourescent Set 20 20 20 60 1,866.60 20 20 20 60 1,866.60 20 20 20 60 1,866.60 20 20 20 60 1,866.60 240 31.11 7,466.40 106 44121708-mp-b01 Marker, Permanent, Black Piece 60 60 60 180 1,488.60 60 60 60 180 1,488.60 60 60 60 180 1,488.60 60 60 60 180 1,488.60 720 8.27 5,954.40 107 44121708-mp-b02 Marker, Permanent, Blue Piece 60 60 60 180 1,488.60 60 60 60 180 1,488.60 60 60 60 180 1,488.60 60 60 60 180 1,488.60 720 8.27 5,954.40 108 44121708-mp-b03 Marker, Permanent, Red Piece 0 0 12 12 99.24 0 0 12 12 99.24 0 0 12 12 99.24 0 0 12 12 99.24 48 8.27 396.96 109 44121708-mw-b01 Marker, Whiteboard, Black Piece 15 15 15 45 434.25 15 15 15 45 434.25 15 15 15 45 434.25 15 15 15 45 434.25 180 9.65 1,737.00 110 44121708-mw-b02 Marker, Whiteboard, Blue Piece 15 15 15 45 434.25 15 15 15 45 434.25 15 15 15 45 434.25 15 15 15 45 434.25 180 9.65 1,737.00 Item & Specifications Unit Of Measure Monthly Quantity Requirement Total Quantity For The Year Price Total Amount For The Year Jan Feb Mar Q1 Q1 Amount April May June Q2 Q2 Amount July Aug Sept Q3 Q3 Amount Oct Nov Dec Q4 Q4 Amount 111 44121708-mw-b03 Marker, Whiteboard, Red Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 9.65 0.00 112 44122104-pc-g01 Paper Clip, Vinly/plastic Coated, 33mm Box 15 15 15 45 396.90 15 15 15 45 396.90 15 15 15 45 396.90 15 15 15 45 396.90 180 8.82 1,587.60 113 44122104-pc-j02 Paper Clip, Vinly/plastic Coated, Jumbo, 50mm Box 15 15 15 45 875.70 15 15 15 45 875.70 15 15 15 45 875.70 15 15 15 45 875.70 180 19.46 3,502.80 114 44101603-ps-m02 Paper Shredder Unit 0 0 1 1 18,718.96 0 0 0 0 0.00 0 0 1 1 18,718.96 0 0 0 0 0.00 2 18,718.96 37,437.92 115 44101601-pt-m02 Paper Trimmer/cutting Machine Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 9,297.60 0.00 116 44121706-pe-l01 Pencil, Lead/graphite, With Eraser Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 44.71 0.00 117 44121619-ps-m01 Pencil Sharpener Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 236.08 0.00 118 44101602-pu-p01 Puncher, Paper, Heavy Duty Piece 5 5 5 15 2,308.80 5 5 5 15 2,308.80 5 5 5 15 2,308.80 5 5 5 15 2,308.80 60 153.92 9,235.20 119 44122101-ru-b01 Rubber Band No. 18 Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 135.20 0.00 120 44121905-sp-f01 Stamp Pad, Felt Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 39.92 0.00 121 44121618-ss-s01 Scissors, Symmetrical/asymmetrical Pair 5 5 5 15 982.80 5 5 5 15 982.80 5 5 5 15 982.80 5 5 5 15 982.80 60 65.52 3,931.20 122 44121615-st-s01 Stapler, Standard Type Piece 0 0 10 10 1,976.00 0 0 10 10 1,976.00 0 0 10 10 1,976.00 0 0 10 10 1,976.00 40 197.60 7,904.00 123 44121615-st-b01 Stapler, Heavy Duty (binder) Unit 0 0 1 1 693.15 0 0 0 0 0.00 0 0 1 1 693.15 0 0 0 0 0.00 2 693.15 1,386.30 124 44121613-sr-p02 Staple Remover, Plier-type Piece 15 15 15 45 2,092.95 15 15 15 45 2,092.95 15 15 15 45 2,092.95 15 15 15 45 2,092.95 180 46.51 8,371.80 125 44121605-td-t01 Tape Dispenser, Table Top Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 77.58 0.00 Paper Materials And Products 126 14111525-ca-a01 Cartolina, Assorted Colors Pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 83.72 0.00 127 14111506-cf-l11 Computer Continuous Form, 1 Ply, 280mm X 241mm Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 945.36 0.00 128 14111506-cf-l12 Computer Continuous Form, 1 Ply, 280mm X 378mm Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,973.92 0.00 129 14111514-np-s02 Notepad, Stick-on, 50mm X 76mm Pad 30 30 30 90 3,335.40 30 30 30 90 3,335.40 30 30 30 90 3,335.40 30 30 30 90 3,335.40 360 37.06 13,341.60 130 14111514-np-s04 Notepad, Stick-on, 76mm X 100mm Pad 30 30 30 90 5,335.20 30 30 30 90 5,335.20 30 30 30 90 5,335.20 30 30 30 90 5,335.20 360 59.28 21,340.80 131 14111514-np-s03 Notepad, Stick-on, 76mm X 76mm Pad 30 30 30 90 4,680.00 30 30 30 90 4,680.00 30 30 30 90 4,680.00 30 30 30 90 4,680.00 360 52.00 18,720.00 132 14111514-nb-s02 Steno Notebook Piece 0 0 20 20 280.80 0 0 20 20 280.80 0 0 20 20 280.80 0 0 20 20 280.80 80 14.04 1,123.20 133 14111507-pp-m01 Paper, Multicopy A4 Ream 50 50 50 150 32,070.00 50 50 50 150 32,070.00 50 50 50 150 32,070.00 50 50 50 150 32,070.00 600 213.80 128,280.00 134 14111507-pp-m02 Paper, Multicopy Legal Ream 10 10 10 30 6,988.80 10 10 10 30 6,988.80 10 10 10 30 6,988.80 10 10 10 30 6,988.80 120 232.96 27,955.20 135 14111507-pp-c01 Paper, Multipurpose A4 Ream 50 50 50 150 20,661.00 50 50 50 150 20,661.00 50 50 50 150 20,661.00 50 50 50 150 20,661.00 600 137.74 82,644.00 136 14111507-pp-c02 Paper, Multipurpose Legal Ream 10 10 10 30 4,767.30 10 10 10 30 4,767.30 10 10 10 30 4,767.30 10 10 10 30 4,767.30 120 158.91 19,069.20 137 14111531-pp-r01 Pad Paper, Ruled Pad 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 34.82 0.00 138 14111503-pa-p01 Paper, Parchment Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 154.21 0.00 139 14111531-re-b01 Record Book, 300 Pages Book 10 10 10 30 2,751.00 10 10 10 30 2,751.00 10 10 10 30 2,751.00 10 10 10 30 2,751.00 120 91.70 11,004.00 140 14111531-re-b02 Record Book, 500 Pages Book 20 20 20 60 7,473.60 20 20 20 60 7,473.60 20 20 20 60 7,473.60 20 20 20 60 7,473.60 240 124.56 29,894.40 141 14111704-tt-p04 Tissue, Interfolded Paper Towel Pack 100 100 100 300 10,140.00 100 100 100 300 10,140.00 100 100 100 300 10,140.00 100 100 100 300 10,140.00 1200 33.80 40,560.00 142 14111704-tt-p02 Toilet Tissue Paper, 2 Ply Pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 99.84 0.00 Perfumes Or Colognes Or Fragrances 143 53131626-hs-s01 Hand Sanitizer Bottle 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 85.08 0.00 Pesticides Or Pest Repellents 144 10191509-in-a01 Insecticide Can 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 139.36 0.00 Printed Publications 145 55101524-ra-h01 Handbook On Philippine Government Procurement (ra 9184 And Its Irr) Book 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 37.21 0.00 Printer Or Facsimile Or Photocopier Supplies (consumables) 1 44103109-br-d05 Drum Cartridge, Brother Dr-3455, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 6,947.20 0.00 2 44103105-ca-c04 Ink Cartridge, Canon Cl-741, Colored Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,126.32 0.00 3 44103105-ca-c02 Ink Cartridge, Canon Cl-811, Colored Cart 10 10 10 30 35,349.60 10 10 10 30 35,349.60 10 10 10 30 35,349.60 10 10 10 30 35,349.60 120 1,178.32 141,398.40 4 44103105-ca-b04 Ink Cartridge, Canon Pg-740, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 861.12 0.00 5 44103105-ca-b02 Ink Cartridge, Canon Pg-810, Black Cart 20 20 20 60 53,539.20 20 20 20 60 53,539.20 20 20 20 60 53,539.20 20 20 20 60 53,539.20 240 892.32 214,156.80 6 44103105-ep-b17 Ink Cartridge, Epson C13t664100 (t6641), Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 231.90 0.00 7 44103105-ep-c17 Ink Cartridge, Epson C13t664200 (t6642), Cyan Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 242.20 0.00 8 44103105-ep-m17 Ink Cartridge, Epson C13t664300 (t6643), Magenta Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 242.20 0.00 9 44103105-ep-y17 Ink Cartridge, Epson C13t664400 (t6644), Yellow Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 242.20 0.00 Item & Specifications Unit Of Measure Monthly Quantity Requirement Total Quantity For The Year Price Total Amount For The Year Jan Feb Mar Q1 Q1 Amount April May June Q2 Q2 Amount July Aug Sept Q3 Q3 Amount Oct Nov Dec Q4 Q4 Amount 10 44103105-hp-b40 Ink Cartridge, Hp C2p04aa (hp62), Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 852.80 0.00 11 44103105-hp-t40 Ink Cartridge, Hp C2p06aa (hp62), Tri-color Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,048.32 0.00 12 44103105-hp-b09 Ink Cartridge, Hp C9351aa (hp21), Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 910.00 0.00 13 44103105-hp-t10 Ink Cartridge, Hp C9352aa (hp22), Tri-color Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,053.52 0.00 14 44103105-hp-b17 Ink Cartridge, Hp Cc640wa (hp60), Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 880.88 0.00 15 44103105-hp-t17 Ink Cartridge, Hp Cc643wa (hp60), Tri-color Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,047.28 0.00 16 44103105-hx-c40 Ink Cartridge, Hp Cd972aa (hp920xl), Cyan Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 823.68 0.00 17 44103105-hx-m40 Ink Cartridge, Hp Cd973aa (hp920xl), Magenta Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 823.68 0.00 18 44103105-hx-y40 Ink Cartridge, Hp Cd974aa (hp920xl), Yellow Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 823.68 0.00 19 44103105-hx-b40 Ink Cartridge, Hp Cd975aa (hp920xl), Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,541.28 0.00 20 44103105-hp-b20 Ink Cartridge, Hp Ch561wa (hp61), Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 865.28 0.00 21 44103105-hp-t20 Ink Cartridge, Hp Ch562wa (hp61), Tri-color Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,066.00 0.00 22 44103105-hx-b43 Ink Cartridge, Hp Cn045aa (hp950xl), Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,970.80 0.00 23 44103105-hx-c43 Ink Cartridge, Hp Cn046aa (hp951xl), Cyan Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,517.36 0.00 24 44103105-hx-m43 Ink Cartridge, Hp Cn047aa (hp951xl), Magenta Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,517.36 0.00 25 44103105-hx-y43 Ink Cartridge, Hp Cn048aa (hp951xl), Yellow Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,517.36 0.00 26 44103105-hp-b36 Ink Cartridge, Hp Cn692aa (hp704), Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 419.12 0.00 27 44103105-hp-t36 Ink Cartridge, Hp Cn693aa (hp704), Tri-color Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 419.12 0.00 28 44103105-hp-b33 Ink Cartridge, Hp Cz107aa (hp678), Black Cart 5 5 5 15 6,068.40 5 5 5 15 6,068.40 5 5 5 15 6,068.40 5 5 5 15 6,068.40 60 404.56 24,273.60 29 44103105-hp-t33 Ink Cartridge, Hp Cz108aa (hp678), Tri-color Cart 5 5 5 15 6,068.40 5 5 5 15 6,068.40 5 5 5 15 6,068.40 5 5 5 15 6,068.40 60 404.56 24,273.60 30 44103105-hp-t43 Ink Cartridge, Hp F6v26aa (hp680), Tri-color Cart 20 20 20 60 25,459.20 20 20 20 60 25,459.20 20 20 20 60 25,459.20 20 20 20 60 25,459.20 240 424.32 101,836.80 31 44103105-hp-b43 Ink Cartridge, Hp F6v27aa (hp680), Black Cart 25 25 25 75 31,824.00 25 25 25 75 31,824.00 25 25 25 75 31,824.00 25 25 25 75 31,824.00 300 424.32 127,296.00 32 44103105-hp-c50 Ink Cartridge, Hp L0s51aa (hp955), Cyan Original Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 982.80 0.00 33 44103105-hp-m50 Ink Cartridge, Hp L0s54aa (hp955), Magenta Original Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 982.80 0.00 34 44103105-hp-y50 Ink Cartridge, Hp L0s57aa (hp955), Yellow Original Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 982.80 0.00 35 44103105-hp-b50 Ink Cartridge, Hp L0s60aa (hp955), Black Original Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,294.80 0.00 36 44103105-hx-c48 Ink Cartridge, Hp L0s63aa (hp955xl), Cyan Original Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,339.52 0.00 37 44103105-hx-m48 Ink Cartridge, Hp L0s66aa (hp955xl), Magenta Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,339.52 0.00 38 44103105-hx-y48 Ink Cartridge, Hp L0s69aa (hp955xl), Yellow Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,339.52 0.00 39 44103105-hx-b48 Ink Cartridge, Hp L0s72aa (hp955xl), Black Original Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 1,817.92 0.00 40 44103105-hp-c51 Ink Cartridge, Hp T6l89aa (hp905), Cyan Original Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 468.00 0.00 41 44103105-hp-m51 Ink Cartridge, Hp T6l93aa (hp905), Magenta Original Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 468.00 0.00 42 44103105-hp-y51 Ink Cartridge, Hp T6l97aa (hp905), Yellow Original Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 468.00 0.00 43 44103105-hp-b51 Ink Cartridge, Hp T6m01aa (hp905), Black Original Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 774.80 0.00 44 44103112-ep-r05 Ribbon Cartridge, Epson C13s015516 (#8750), Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 77.43 0.00 45 44103112-ep-r13 Ribbon Cartridge, Epson C13s015632, Black Cart 4 4 4 12 935.28 4 4 4 12 935.28 4 4 4 12 935.28 4 4 4 12 935.28 48 77.94 3,741.12 46 44103112-ep-r07 Ribbon Cartridge, Epson C13s015531 (s015086) Cart 1 1 1 3 2,455.44 1 1 1 3 2,455.44 1 1 1 3 2,455.44 1 1 1 3 2,455.44 12 818.48 9,821.76 47 44103103-br-b09 Toner Cartridge, Brother Tn-3320, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 3,567.20 0.00 48 44103103-br-b11 Toner Cartridge, Brother Tn-3350, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 5,002.40 0.00 49 44103103-br-b15 Toner Cartridge, Brother Tn-3478, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 5,575.44 0.00 50 44103103-br-b16 Toner Cartridge, Brother Tn-456 Black, High Yield Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 4,564.56 0.00 51 44103103-br-c03 Toner Cartridge, Brother Tn-456 Cyan, High Yield Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 7,716.80 0.00 52 44103103-br-m03 Toner Cartridge, Brother Tn-456 Magenta, High Yield Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 7,716.80 0.00 53 44103103-br-y03 Toner Cartridge, Brother Tn-456 Yellow, High Yield Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 7,716.80 0.00 54 44103103-ca-b00 Toner Cartridge, Canon Crg-324 Ii Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 13,399.36 0.00 55 44103103-hp-b12 Toner Cartridge, Hp Cb435a, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 3,439.28 0.00 56 44103103-hp-b18 Toner Cartridge, Hp Ce255a, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 7,705.36 0.00 57 44103103-hp-b21 Toner Cartridge, Hp Ce278a, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 4,152.72 0.00 58 44103103-hp-b22 Toner Cartridge, Hp Ce285a (hp85a), Black Cart 10 10 0 20 71,968.00 10 10 0 20 71,968.00 10 10 0 20 71,968.00 10 10 0 20 71,968.00 80 3,598.40 287,872.00 Item & Specifications Unit Of Measure Monthly Quantity Requirement Total Quantity For The Year Price Total Amount For The Year Jan Feb Mar Q1 Q1 Amount April May June Q2 Q2 Amount July Aug Sept Q3 Q3 Amount Oct Nov Dec Q4 Q4 Amount 59 44103103-hp-b23 Toner Cartridge, Hp Ce310a, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 2,608.32 0.00 60 44103103-hp-c23 Toner Cartridge, Hp Ce311a, Cyan Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 2,897.44 0.00 61 44103103-hp-y23 Toner Cartridge, Hp Ce312a, Yellow Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 2,897.44 0.00 62 44103103-hp-m23 Toner Cartridge, Hp Ce313a, Magenta Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 2,897.44 0.00 63 44103103-hp-b28 Toner Cartridge, Hp Ce505a, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 4,495.92 0.00 64 44103103-hp-b52 Toner Cartridge, Hp Cf217a (hp17a), Black Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 3,194.88 0.00 65 44103103-hp-b53 Toner Cartridge, Hp Cf226a (hp26a), Black Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 5,822.96 0.00 66 44103103-hp-b56 Toner Cartridge, Hp Cf281a (hp81a), Black Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 8,658.00 0.00 67 44103103-hp-b57 Toner Cartridge, Hp Cf283a (hp83a), Laserjet Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 3,367.52 0.00 68 44103103-hp-b58 Toner Cartridge, Hp Cf287a (hp87), Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 10,908.56 0.00 69 44103103-hp-b60 Toner Cartridge, Hp Cf350a, Black Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 2,856.88 0.00 70 44103103-hp-c60 Toner Cartridge, Hp Cf351a, Cyan Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 2,943.20 0.00 71 44103103-hp-y60 Toner Cartridge, Hp Cf352a, Yellow Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 2,943.20 0.00 72 44103103-hp-m60 Toner Cartridge, Hp Cf353a, Magenta Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 2,943.20 0.00 73 44103103-hp-b61 Toner Cartridge, Hp Cf360a (hp508a), Black Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 7,803.12 0.00 74 44103103-hp-c61 Toner Cartridge, Hp Cf361a (hp508a), Cyan Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 9,783.28 0.00 75 44103103-hp-y61 Toner Cartridge, Hp Cf362a (hp508a), Yellow Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 9,783.28 0.00 76 44103103-hp-m61 Toner Cartridge, Hp Cf363a (hp508a), Magenta Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 9,783.28 0.00 77 44103103-hp-b62 Toner Cartridge, Hp Cf400a (hp201a), Black Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 3,439.28 0.00 78 44103103-hp-c62 Toner Cartridge, Hp Cf401a (hp201a), Cyan Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 4,063.28 0.00 79 44103103-hp-y62 Toner Cartridge, Hp Cf402a (hp201a), Yellow Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 4,063.28 0.00 80 44103103-hp-m62 Toner Cartridge, Hp Cf403a (hp201a), Magenta Laserjet Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 4,063.28 0.00 81 44103103-hp-b63 Toner Cartridge, Hp Cf410a (hp410a), Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 4,328.48 0.00 82 44103103-hp-c63 Toner Cartridge, Hp Cf411a (hp410a), Cyan Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 5,592.08 0.00 83 44103103-hp-y63 Toner Cartridge, Hp Cf412a (hp410a), Yellow Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 5,592.08 0.00 84 44103103-hp-m63 Toner Cartridge, Hp Cf413a (hp410a), Magenta Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 5,592.08 0.00 85 44103103-hp-b34 Toner Cartridge, Hp Q2612a, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 4,155.84 0.00 86 44103103-hp-b48 Toner Cartridge, Hp Q7553a, Black Cart 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 4,680.00 0.00 Software 1 43231513-sft-001 Business Function Specific Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 2 43231602-sft-002 Finance Accounting And Enterprise Resource Planning Erp Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 3 43232004-sft-003 Computer Game Or Entertainment Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 4 43232107-sft-004 Content Authoring And Editing Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 5 43232202-sft-005 Content Management Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 6 43232304-sft-006 Data Management And Query Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 7 43232402-sft-007 Development Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 8 43232505-sft-008 Educational Or Reference Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 9 43232603-sft-009 Industry Specific Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 10 43233501-sft-016 Information Exchange Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 11 43232701-sft-010 Network Applications Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 12 43232802-sft-011 Network Management Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 13 43232905-sft-012 Networking Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 14 43233004-sft-013 Operating Environment Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 15 43233205-sft-014 Security And Protection Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 16 43233405-sft-015 Utility And Device Driver Software License 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 Part Ii. Other Items Not Available At Ps-dbm But Are Regularly Purchased From Other Sources (note: Please Indicate Price Of Items) 1 80141505-ts-001 Ballpen Piece 100 100 100 300 3,900.00 100 100 100 300 3,900.00 100 100 100 300 3,900.00 100 100 100 300 3,900.00 1200 13.00 15,600.00 2 80141505-ts-002 Multifunction Printer Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 3 80141505-ts-003 Laminating Film Pack 5 5 5 15 6,000.00 5 5 5 15 6,000.00 5 5 5 15 6,000.00 5 5 5 15 6,000.00 60 400.00 24,000.00 Item & Specifications Unit Of Measure Monthly Quantity Requirement Total Quantity For The Year Price Total Amount For The Year Jan Feb Mar Q1 Q1 Amount April May June Q2 Q2 Amount July Aug Sept Q3 Q3 Amount Oct Nov Dec Q4 Q4 Amount 4 80141505-ts-004 Sticker Paper Pack 0 0 10 10 600.00 0 0 10 10 600.00 0 0 10 10 600.00 0 0 10 10 600.00 40 60.00 2,400.00 5 80141505-ts-005 Double Sided Tape Roll 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 6 80141505-ts-006 Photo Paper Pack 0 0 10 10 1,900.00 0 0 10 10 1,900.00 0 0 10 10 1,900.00 0 0 10 10 1,900.00 40 190.00 7,600.00 7 80141505-ts-007 Bleaching Solution Bottle 0 0 0 0 0.00 0 0 50 50 12,000.00 0 0 0 0 0.00 0 0 50 50 12,000.00 100 240.00 24,000.00 8 80141505-ts-008 Certificate Frame Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 9 80141505-ts-009 Certificate Holder Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 10 80141505-ts-010 Uninterruptible Power Supply Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 11 80141505-ts-011 Air Conditioning Unit Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 12 80141505-ts-012 Smart Television Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 13 80141505-ts-013 White Board Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 14 80141505-ts-014 Microphone Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 15 80141505-ts-015 Medal Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 16 80141505-ts-016 Dishwashing Liquid Bottle 10 10 10 30 9,900.00 10 10 10 30 9,900.00 10 10 10 30 9,900.00 10 10 10 30 9,900.00 120 330.00 39,600.00 17 80141505-ts-017 Plastic Fastener Box 10 10 10 30 1,410.00 10 10 10 30 1,410.00 10 10 10 30 1,410.00 10 10 10 30 1,410.00 120 47.00 5,640.00 18 80141505-ts-018 Steel Filing Cabinet Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 19 80141505-ts-019 Vellum Board Paper Pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 20 80141505-ts-020 Extension Cord Piece 0 0 0 0 0.00 5 5 5 15 18,000.00 0 0 0 0 0.00 5 5 5 15 18,000.00 30 1,200.00 36,000.00 21 80141505-ts-021 Paint Gallon 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 22 80141505-ts-022 Colored Paper Pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 23 80141505-ts-023 Bond Paper Ream 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 24 80141505-ts-024 Push Pin Pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 25 80141505-ts-025 Door Mat Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 26 80141505-ts-026 Glue Stick (paste) Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 27 80141505-ts-027 Glue Stick (for Glue Gun) Pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 28 80141505-ts-028 Deodorant Cake Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 29 80141505-ts-029 Disposable Gloves Box 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 30 80141505-ts-030 Office Chair Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 31 80141505-ts-031 Manila Paper Pack 0 0 10 10 800.00 0 0 0 0 0.00 0 0 10 10 800.00 0 0 0 0 0.00 20 80.00 1,600.00 32 80141505-ts-032 Automotive Batteries Piece 0 1 0 1 7,500.00 0 1 0 1 7,500.00 0 1 0 1 7,500.00 0 1 0 1 7,500.00 4 7,500.00 30,000.00 33 80141505-ts-033 Padlock Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 34 80141505-ts-034 Mobile Phone Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 35 80141505-ts-035 Compact Disc Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 36 80141505-ts-036 Amplifier Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 37 80141505-ts-037 Storage Box Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 38 80141505-ts-038 Plastic Envelope Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 39 80141505-ts-039 Document Scanner Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 40 80141505-ts-040 Water Dispenser Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 41 80141505-ts-041 Paracetamol Pack 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 42 80141505-ts-042 Glue Gun Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 43 80141505-ts-043 Inkjet Printer Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 44 80141505-ts-044 Speakers Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 45 80141505-ts-045 Povidone Iodine Bottle 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 46 80141505-ts-046 Keyboard Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 47 80141505-ts-047 Dslr Camera Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 48 80141505-ts-048 Steel Rack Set 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 49 80141505-ts-049 Laminating Machine Unit 0 0 1 1 5,000.00 0 0 0 0 0.00 0 0 1 1 5,000.00 0 0 0 0 0.00 2 5,000.00 10,000.00 50 80141505-ts-050 Fuel Filters Piece 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 51 80141505-ts-051 Airline Tickets (domestic) Ticket 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 52 80141505-ts-052 Airline Tickets (international) Ticket 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 Item & Specifications Unit Of Measure Monthly Quantity Requirement Total Quantity For The Year Price Total Amount For The Year Jan Feb Mar Q1 Q1 Amount April May June Q2 Q2 Amount July Aug Sept Q3 Q3 Amount Oct Nov Dec Q4 Q4 Amount 53 80141505-ts-053 Car (sedan Or Hatchback) Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 46 80141505-ts-054 Multi-purpose Vehicle (mpv) Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 47 80141505-ts-055 Sports Utility Vehicle (suv) Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 48 80141505-ts-056 Passenger Van Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 49 80141505-ts-057 Van Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 50 80141505-ts-058 Tri-wheel Vehicle Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 51 80141505-ts-059 Pick-up Truck Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 52 80141505-ts-060 All-terrain Vehicle (atv) Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 53 80141505-ts-061 Assembled Owner-type Jeep Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 50 80141505-ts-062 Assembled Passenger Jeepney-type Vehicle Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 51 80141505-ts-063 Motorcycle Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 52 80141505-ts-064 Bus Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 53 80141505-ts-065 Mini Bus Unit 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0 0 0 0.00 0 0.00 0.00 A. Total ₱ 2,576,442.32 B. Additional Provision For Inflation (10% Of Total) ₱ 257,644.23 C. Additional Provision For Transport And Freight Cost (if Applicable) ₱ - D. Grand Total (a + B+ C) ₱ 2,834,086.55 E. Approved Budget By The Agency Head In Figures And Words: We Hereby Warrant That The Total Amount Reflected In This Annual Procurement Plan To Procure The Listed Common-use Supplies, Materials, And Equipment Has Been Included In Or Is Within Our Approved Budget For The Year. Prepared By: Certified Funds Available / Certified Appropriate Funds Available: Approved By: Property/supply Officer Date Prepared: Accountant / Budget Officer Head Of Office/agency

Details: Description Philippine Bidding Documents (as Harmonized With Development Partners) Improvement Of Perimeter Fence At Art Center, Brgy. Nanga, Pototan, Iloilo Bid No. Agr-25-219-b Iloilo Provincial Government Sixth Edition Table Of Contents Glossary Of Terms, Abbreviations, And Acronyms 4 Section I. Invitation To Bid 6 Section Ii. Instructions To Bidders 8 1. Scope Of Bid 8 2. Funding Information 8 3. Bidding Requirements 8 4. Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices 8 5. Eligible Bidders 9 6. Origin Of Associated Goods 9 7. Subcontracts 9 8. Pre-bid Conference 9 9. Clarification And Amendment Of Bidding Documents 9 10. Documents Comprising The Bid: Eligibility And Technical Components 10 11. Documents Comprising The Bid: Financial Component 10 12. Alternative Bids 10 13. Bid Prices 11 14. Bid And Payment Currencies 11 15. Bid Security 11 16. Sealing And Marking Of Bids 11 17. Deadline For Submission Of Bids 11 18. Opening And Preliminary Examination Of Bids 12 19. Detailed Evaluation And Comparison Of Bids 12 20. Post Qualification 12 21. Signing Of The Contract 12 Section Iii. Bid Data Sheet 13 Section Iv. General Conditions Of Contract 15 1. Scope Of Contract 15 2. Sectional Completion Of Works 15 3. Possession Of Site 15 4. The Contractor’s Obligations 15 5. Performance Security 16 6. Site Investigation Reports 16 7. Warranty 16 8. Liability Of The Contractor 16 9. Termination For Other Causes 16 10. Dayworks 17 11. Program Of Work 17 12. Instructions, Inspections And Audits 17 13. Advance Payment 17 14. Progress Payments 17 15. Operating And Maintenance Manuals 17 Section V. Special Conditions Of Contract 18 Section Vi. Specifications 19 Section Vii. Drawings 27 Section Viii. Bill Of Quantities 49 Section Ix. Checklist Of Technical And Financial Documents 52 Glossary Of Terms, Abbreviations, And Acronyms Abc – Approved Budget For The Contract. Arcc – Allowable Range Of Contract Cost. Bac – Bids And Awards Committee. Bid – A Signed Offer Or Proposal To Undertake A Contract Submitted By A Bidder In Response To And In Consonance With The Requirements Of The Bidding Documents. Also Referred To As Proposal And Tender. (2016 Revised Irr, Section 5[c]) Bidder – Refers To A Contractor, Manufacturer, Supplier, Distributor And/or Consultant Who Submits A Bid In Response To The Requirements Of The Bidding Documents. (2016 Revised Irr, Section 5[d]) Bidding Documents – The Documents Issued By The Procuring Entity As The Bases For Bids, Furnishing All Information Necessary For A Prospective Bidder To Prepare A Bid For The Goods, Infrastructure Projects, And/or Consulting Services Required By The Procuring Entity. (2016 Revised Irr, Section 5[e]) Bir – Bureau Of Internal Revenue. Bsp – Bangko Sentral Ng Pilipinas. Cda – Cooperative Development Authority. Consulting Services – Refer To Services For Infrastructure Projects And Other Types Of Projects Or Activities Of The Gop Requiring Adequate External Technical And Professional Expertise That Are Beyond The Capability And/or Capacity Of The Gop To Undertake Such As, But Not Limited To: (i) Advisory And Review Services; (ii) Pre-investment Or Feasibility Studies; (iii) Design; (iv) Construction Supervision; (v) Management And Related Services; And (vi) Other Technical Services Or Special Studies. (2016 Revised Irr, Section 5[i]) Contract – Refers To The Agreement Entered Into Between The Procuring Entity And The Supplier Or Manufacturer Or Distributor Or Service Provider For Procurement Of Goods And Services; Contractor For Procurement Of Infrastructure Projects; Or Consultant Or Consulting Firm For Procurement Of Consulting Services; As The Case May Be, As Recorded In The Contract Form Signed By The Parties, Including All Attachments And Appendices Thereto And All Documents Incorporated By Reference Therein. Contractor – Is A Natural Or Juridical Entity Whose Proposal Was Accepted By The Procuring Entity And To Whom The Contract To Execute The Work Was Awarded. Contractor As Used In These Bidding Documents May Likewise Refer To A Supplier, Distributor, Manufacturer, Or Consultant. Cpi – Consumer Price Index. Dole – Department Of Labor And Employment. Dti – Department Of Trade And Industry. Foreign-funded Procurement Or Foreign-assisted Project – Refers To Procurement Whose Funding Source Is From A Foreign Government, Foreign Or International Financing Institution As Specified In The Treaty Or International Or Executive Agreement. (2016 Revised Irr, Section 5[b]). Gfi – Government Financial Institution. Gocc – Government-owned And/or –controlled Corporation. Goods – Refer To All Items, Supplies, Materials And General Support Services, Except Consulting Services And Infrastructure Projects, Which May Be Needed In The Transaction Of Public Businesses Or In The Pursuit Of Any Government Undertaking, Project Or Activity, Whether In The Nature Of Equipment, Furniture, Stationery, Materials For Construction, Or Personal Property Of Any Kind, Including Non-personal Or Contractual Services Such As The Repair And Maintenance Of Equipment And Furniture, As Well As Trucking, Hauling, Janitorial, Security, And Related Or Analogous Services, As Well As Procurement Of Materials And Supplies Provided By The Procuring Entity For Such Services. The Term “related” Or “analogous Services” Shall Include, But Is Not Limited To, Lease Or Purchase Of Office Space, Media Advertisements, Health Maintenance Services, And Other Services Essential To The Operation Of The Procuring Entity. (2016 Revised Irr, Section 5[r]) Gop – Government Of The Philippines. Infrastructure Projects – Include The Construction, Improvement, Rehabilitation, Demolition, Repair, Restoration Or Maintenance Of Roads And Bridges, Railways, Airports, Seaports, Communication Facilities, Civil Works Components Of Information Technology Projects, Irrigation, Flood Control And Drainage, Water Supply, Sanitation, Sewerage And Solid Waste Management Systems, Shore Protection, Energy/power And Electrification Facilities, National Buildings, School Buildings, Hospital Buildings, And Other Related Construction Projects Of The Government. Also Referred To As Civil Works Or Works. (2016 Revised Irr, Section 5[u]) Lgus – Local Government Units. Nfcc – Net Financial Contracting Capacity. Nga – National Government Agency. Pcab – Philippine Contractors Accreditation Board. Philgeps - Philippine Government Electronic Procurement System. Procurement Project – Refers To A Specific Or Identified Procurement Covering Goods, Infrastructure Project Or Consulting Services. A Procurement Project Shall Be Described, Detailed, And Scheduled In The Project Procurement Management Plan Prepared By The Agency Which Shall Be Consolidated In The Procuring Entity's Annual Procurement Plan. (gppb Circular No. 06-2019 Dated 17 July 2019) Psa – Philippine Statistics Authority. Sec – Securities And Exchange Commission. Slcc – Single Largest Completed Contract. Un – United Nations. Republic Of The Philippines Iloilo Provincial Government Section I. Invitation To Bid For Improvement Of Perimeter Fence At Art Center, Brgy. Nanga, Pototan, Iloilo Bid No. Agr-25-219-b The Iloilo Provincial Government, Through The 20% Nta Development Fund Fy-2025 Intends To Apply The Sum Of Five Million Pesos (p5,000,000.00) Being The Approved Budget For The Contract (abc) To Payments Under The Contract For Agr-25-219-b For The Improvement Of Perimeter Fence At Art Center, Brgy. Nanga, Pototan, Iloilo For The Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. The Iloilo Provincial Government Now Invites Bids For The Above Procurement Project. Completion Of The Works Is Required Ninety (90) Calendar Days. Bidders Should Have Completed A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii (instructions To Bidders). Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) No. 9184. Interested Bidders May Obtain Further Information From The Bids And Awards Committee Secretariat, 5th Floor, New Iloilo Provincial Capitol, Bonifacio Drive, Iloilo City, Philippines And Inspect The Bidding Documents At The Address Given Below From 8:00am To 5:00pm. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders On March 28, 2025 From Given Address And Website/s Below And Upon Payment Of The Applicable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb, In The Amount Of Five Thousand Pesos (p5, 000,00). The Procuring Entity Shall Allow The Bidder To Present Its Proof Of Payment For The Fees In Person. The Iloilo Provincial Government Will Hold A Pre-bid Conference On April 8, 2025, 9:00 A.m. At Bids And Awards Committee Secretariat, 5th Floor, New Iloilo Provincial Capitol, Bonifacio Drive, Iloilo City, Philippines, And/or Through Videoconferencing/webcasting Via Zoom Conference Which Shall Be Open To Prospective Bidders. The Default Meeting Id And Password Shall Be: Meeting Id: 4340851724 // Password: 0922 Bids Must Be Duly Received By The Bac Secretariat Through Manual Submission At Bids And Awards Committee Secretariat, 5th Floor, New Iloilo Provincial Capitol, Bonifacio Drive, Iloilo City On Or Before April 22, 2025, 9:00 A.m. Late Bids Shall Not Be Accepted. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 16. Bid Opening Shall Be On April 22, 2025, 9:01 A.m. At Bids And Awards Committee Secretariat, 5th Floor, New Iloilo Provincial Capitol, Bonifacio Drive, Iloilo City, Philippines. Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend The Activity. The Iloilo Provincial Government Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Implementing Rules And Regulations (irr) Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. For Further Information, Please Refer To: Atty. Raemman M. Lagrada Head, Bac Secretariat 5f New Iloilo Provincial Capitol Bonifacio Drive, Iloilo City Tel. No. (33) 336-0736 Fax No. (33) 337-7731 Email: Ipg_bacs@yahoo.com You May Visit The Following Websites: For Downloading Of Bidding Documents: Www.iloilo.gov.ph March 17, 2025 Atty. Dennis T. Ventilacion Bac Chairperson Section Ii. Instructions To Bidders Scope Of Bid The Procuring Entity, Iloilo Provincial Government Invites Bids For The Improvement Of Perimeter Fence At Art Center, Brgy. Nanga, Pototan, Iloilo With Project Identification Number Agr-25-219-b. The Procurement Project (referred To Herein As “project”) Is For The Construction Of Works, As Described In Section Vi (specifications). Funding Information The Gop Through The Source Of Funding As Indicated Below For 2025 In The Amount Of Five Million Pesos (p5,000,000.00) The Source Of Funding Is: A. Lgu’s, 20% Nta Development Fund Fy 2025 As Approved By The Sanggunian. Bidding Requirements The Bidding For The Project Shall Be Governed By All The Provisions Of Ra No. 9184 And Its 2016 Revised Irr, Including Its Generic Procurement Manual And Associated Policies, Rules And Regulations As The Primary Source Thereof, While The Herein Clauses Shall Serve As The Secondary Source Thereof. Any Amendments Made To The Irr And Other Gppb Issuances Shall Be Applicable Only To The Ongoing Posting, Advertisement, Or Invitation To Bid By The Bac Through The Issuance Of A Supplemental Or Bid Bulletin. The Bidder, By The Act Of Submitting Its Bid, Shall Be Deemed To Have Inspected The Site, Determined The General Characteristics Of The Contracted Works And The Conditions For This Project, Such As The Location And The Nature Of The Work; (b) Climatic Conditions; (c) Transportation Facilities; (c) Nature And Condition Of The Terrain, Geological Conditions At The Site Communication Facilities, Requirements, Location And Availability Of Construction Aggregates And Other Materials, Labor, Water, Electric Power And Access Roads; And (d) Other Factors That May Affect The Cost, Duration And Execution Or Implementation Of The Contract, Project, Or Work And Examine All Instructions, Forms, Terms, And Project Requirements In The Bidding Documents. Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices The Procuring Entity, As Well As The Bidders And Contractors, Shall Observe The Highest Standard Of Ethics During The Procurement And Execution Of The Contract. They Or Through An Agent Shall Not Engage In Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices Defined Under Annex “i” Of The 2016 Revised Irr Of Ra No. 9184 Or Other Integrity Violations In Competing For The Project. Eligible Bidders Only Bids Of Bidders Found To Be Legally, Technically, And Financially Capable Will Be Evaluated. The Bidder Must Have An Experience Of Having Completed A Single Largest Completed Contract (slcc) That Is Similar To This Project, Equivalent To At Least Fifty Percent (50%) Of The Abc Adjusted, If Necessary, By The Bidder To Current Prices Using The Psa’s Cpi, Except Under Conditions Provided For In Section 23.4.2.4 Of The 2016 Revised Irr Of Ra No. 9184. A Contract Is Considered To Be “similar” To The Contract To Be Bid If It Has The Major Categories Of Work Stated In The Bds. For Foreign-funded Procurement, The Procuring Entity And The Foreign Government/foreign Or International Financing Institution May Agree On Another Track Record Requirement, As Specified In The Bidding Document Prepared For This Purpose. The Bidders Shall Comply With The Eligibility Criteria Under Section 23.4.2 Of The 2016 Irr Of Ra No. 9184. Origin Of Associated Goods There Is No Restriction On The Origin Of Goods Other Than Those Prohibited By A Decision Of The Un Security Council Taken Under Chapter Vii Of The Charter Of The Un. Subcontracts The Bidder May Subcontract Portions Of The Project To The Extent Allowed By The Procuring Entity As Stated Herein, But In No Case More Than Fifty Percent (50%) Of The Project. The Procuring Entity Has Prescribed That: Subcontracting Is Not Allowed. Pre-bid Conference The Procuring Entity Will Hold A Pre-bid Conference For This Project On The Specified Date And Time And Either At Its Physical Address At Bac Office, 5th Floor, New Iloilo Provincial Capitol, Iloilo City And/or Through Videoconferencing As Indicated In Paragraph 6 Of The Ib. Clarification And Amendment Of Bidding Documents Prospective Bidders May Request For Clarification On And/or Interpretation Of Any Part Of The Bidding Documents. Such Requests Must Be In Writing And Received By The Procuring Entity, Either At Its Given Address Or Through Electronic Mail Indicated In The Ib, At Least Ten (10) Calendar Days Before The Deadline Set For The Submission And Receipt Of Bids. Documents Comprising The Bid: Eligibility And Technical Components The First Envelope Shall Contain The Eligibility And Technical Documents Of The Bid As Specified In Section Ix. Checklist Of Technical And Financial Documents. If The Eligibility Requirements Or Statements, The Bids, And All Other Documents For Submission To The Bac Are In Foreign Language Other Than English, It Must Be Accompanied By A Translation In English, Which Shall Be Authenticated By The Appropriate Philippine Foreign Service Establishment, Post, Or The Equivalent Office Having Jurisdiction Over The Foreign Bidder’s Affairs In The Philippines. For Contracting Parties To The Apostille Convention, Only The Translated Documents Shall Be Authenticated Through An Apostille Pursuant To Gppb Resolution No. 13-2019 Dated 23 May 2019. The English Translation Shall Govern, For Purposes Of Interpretation Of The Bid. In Joint Ventures, A Special Pcab License, And Registration For The Type And Cost Of The Contract For This Project, Shall Be Required. Any Additional Type Of Contractor License Or Permit Shall Be Indicated In The Bds. A List Of Contractor’s Key Personnel (e.g., Project Manager, Project Engineers, Materials Engineers, And Foremen) Assigned To The Contract To Be Bid, With Their Complete Qualification And Experience Data Shall Be Provided. These Key Personnel Must Meet The Required Minimum Years Of Experience Set In The Bds. A List Of Contractor’s Major Equipment Units, Which Are Owned, Leased, And/or Under Purchase Agreements, Supported By Proof Of Ownership, Certification Of Availability Of Equipment From The Equipment Lessor/vendor For The Duration Of The Project, As The Case May Be, Must Meet The Minimum Requirements For The Contract Set In The Bds. Documents Comprising The Bid: Financial Component The Second Bid Envelope Shall Contain The Financial Documents For The Bid As Specified In Section Ix. Checklist Of Technical And Financial Documents. Any Bid Exceeding The Abc Indicated In Paragraph 1 Of The Ib Shall Not Be Accepted. For Foreign-funded Procurement, A Ceiling May Be Applied To Bid Prices Provided The Conditions Are Met Under Section 31.2 Of The 2016 Revised Irr Of Ra No. 9184. Alternative Bids Bidders Shall Submit Offers That Comply With The Requirements Of The Bidding Documents, Including The Basic Technical Design As Indicated In The Drawings And Specifications. Unless There Is A Value Engineering Clause In The Bds, Alternative Bids Shall Not Be Accepted. Bid Prices All Bid Prices For The Given Scope Of Work In The Project As Awarded Shall Be Considered As Fixed Prices, And Therefore Not Subject To Price Escalation During Contract Implementation, Except Under Extraordinary Circumstances As Determined By The Neda And Approved By The Gppb Pursuant To The Revised Guidelines For Contract Price Escalation Guidelines. Bid And Payment Currencies Bid Prices May Be Quoted In The Local Currency Or Tradeable Currency Accepted By The Bsp At The Discretion Of The Bidder. However, For Purposes Of Bid Evaluation, Bids Denominated In Foreign Currencies Shall Be Converted To Philippine Currency Based On The Exchange Rate As Published In The Bsp Reference Rate Bulletin On The Day Of The Bid Opening. Payment Of The Contract Price Shall Be Made In: Philippine Pesos. Bid Security The Bidder Shall Submit A Bid Securing Declaration Or Any Form Of Bid Security In The Amount Indicated In The Bds, Which Shall Be Not Less Than The Percentage Of The Abc In Accordance With The Schedule In The Bds. The Bid And Bid Security Shall Be Valid Until August 20, 2025. Any Bid Not Accompanied By An Acceptable Bid Security Shall Be Rejected By The Procuring Entity As Non-responsive. Sealing And Marking Of Bids Each Bidder Shall Submit One Copy Of The First And Second Components Of Its Bid. The Procuring Entity May Request Additional Hard Copies And/or Electronic Copies Of The Bid. However, Failure Of The Bidders To Comply With The Said Request Shall Not Be A Ground For Disqualification. If The Procuring Entity Allows The Submission Of Bids Through Online Submission To The Given Website Or Any Other Electronic Means, The Bidder Shall Submit An Electronic Copy Of Its Bid, Which Must Be Digitally Signed. An Electronic Copy That Cannot Be Opened Or Is Corrupted Shall Be Considered Non-responsive And, Thus, Automatically Disqualified. Deadline For Submission Of Bids The Bidders Shall Submit On The Specified Date And Time And Either At Its Physical Address Or Through Online Submission As Indicated In Paragraph 7 Of The Ib. Opening And Preliminary Examination Of Bids The Bac Shall Open The Bids In Public At The Time, On The Date, And At The Place Specified In Paragraph 9 Of The Ib. The Bidders’ Representatives Who Are Present Shall Sign A Register Evidencing Their Attendance. In Case Videoconferencing, Webcasting Or Other Similar Technologies Will Be Used, Attendance Of Participants Shall Likewise Be Recorded By The Bac Secretariat. In Case The Bids Cannot Be Opened As Scheduled Due To Justifiable Reasons, The Rescheduling Requirements Under Section 29 Of The 2016 Revised Irr Of Ra No. 9184 Shall Prevail. The Preliminary Examination Of Bids Shall Be Governed By Section 30 Of The 2016 Revised Irr Of Ra No. 9184. Detailed Evaluation And Comparison Of Bids The Procuring Entity’s Bac Shall Immediately Conduct A Detailed Evaluation Of All Bids Rated “passed” Using Non-discretionary Pass/fail Criteria. The Bac Shall Consider The Conditions In The Evaluation Of Bids Under Section 32.2 Of 2016 Revised Irr Of Ra No. 9184. If The Project Allows Partial Bids, All Bids And Combinations Of Bids As Indicated In The Bds Shall Be Received By The Same Deadline And Opened And Evaluated Simultaneously So As To Determine The Bid Or Combination Of Bids Offering The Lowest Calculated Cost To The Procuring Entity. Bid Security As Required By Itb Clause 16 Shall Be Submitted For Each Contract (lot) Separately. In All Cases, The Nfcc Computation Pursuant To Section 23.4.2.6 Of The 2016 Revised Irr Of Ra No. 9184 Must Be Sufficient For The Total Of The Abcs For All The Lots Participated In By The Prospective Bidder. Post Qualification Within A Non-extendible Period Of Five (5) Calendar Days From Receipt By The Bidder Of The Notice From The Bac That It Submitted The Lowest Calculated Bid, The Bidder Shall Submit Its Latest Income And Business Tax Returns Filed And Paid Through The Bir Electronic Filing And Payment System (efps), And Other Appropriate Licenses And Permits Required By Law And Stated In The Bds. Signing Of The Contract The Documents Required In Section 37.2 Of The 2016 Revised Irr Of Ra No. 9184 Shall Form Part Of The Contract. Additional Contract Documents Are Indicated In The Bds. Section Iii. Bid Data Sheet Itb Clause 5.2 For This Purpose, Contracts Similar To The Project Refer To Contracts Which Have The Same Major Categories Of Work, Which Shall Be: Structural Works 7.1 The Procuring Entity Has Prescribed That Subcontracting Is Not Allowed. 10.3 [specify If Another Contractor License Or Permit Is Required.] 10.4 The Key Personnel Must Meet The Required Minimum Years Of Experience Set Below: Key Personnel General Experience Relevant Experience 1-project Engineer 1 Year 1 Year 1-material Engineer 1 Year 1 Year 1-health & Safety Officer 1 Year 1 Year 1-foreman 1 Year 1 Year 10.5 The Minimum Major Equipment Requirements Are The Following: Equipment Capacity Number Of Units Bar Cutter & Bar Bender - 1 Concrete Vibrator - 1 One-bagger Mixer - 1 Generator - 1 12 Alternative Bids Are Not Allowed 15.1 The Bid Security Shall Be In The Form Of A Bid Securing Declaration Or Any Of The Following Forms And Amounts: The Amount Of Not Less Than Two Percent (2%) Of Abc, If Bid Security Is In Cash, Cashier’s/manager’s Check, Bank Draft/guarantee Or Irrevocable Letter Of Credit; The Amount Of Not Less Than Five Percent (5%) Of Abc If Bid Security Is In Surety Bond. 16 Bidders Shall Prepare An Original Of The First (eligibility And Technical) And Second (financial) Envelopes. In Addition, Bidders Shall Submit Separate Copies Of The First And Second Envelopes (copy 1, Copy 2) And Each Set Of Documents Must Clearly Indicate Whether The Same Is Original, Copy 1, Or Copy 2. In The Event Of Any Discrepancy Between The Original And The Copies, The Original Shall Prevail. Itb Clause 16 All Envelopes Shall: A. Contain The Name Of The Contract To Be Bid In Capital Letters: “improvement Of Perimeter Fence At Art Center, Brgy. Nanga, Pototan, Iloilo” B. Bear The Name And Address Of The Bidder In Capital Letters; Addressed To: Atty. Dennis T. Ventilacion, Chairperson, Bids And Awards Committee: D. Bear The Specific Identification Of This Procurement: “agr-25-219-b” E. Bear A Warning “do Not Open Before April 22, 2025” Indicating The Date And Time For The Submission Of Bids On The Blank: Bid Envelopes That Are Not Properly Sealed And Marked, As Required In The Bidding Documents, Shall Not Be Rejected, But The Bidder Or Its Duly Authorized Representative Shall Acknowledge Such Condition Of The Bid As Submitted. The Bac Or The Procuring Entity Shall Assume No Responsibility For The Misplacement Of The Contents Of The Improperly Sealed Or Marked Bid, Or For Its Premature Opening. Any Interlineations, Erasures, Or Overwriting Shall Be Valid Only If They Are Signed Or Initialed By The Duly Authorized Representative/s Of The Bidder 19.2 Partial Bid Is Not Allowed 20 No Further Instructions. 21 The Additional Contract Documents Relevant To The Project That Are Required By The Procuring Entity Are: A. Construction Schedule And S-curve; B. Manpower Schedule; C. Construction Methods; D. Equipment Utilization Schedule; E. Construction Safety And Health Program Approved By The Department Of Labor And Employment; And F. Pert/cpm Section Iv. General Conditions Of Contract Scope Of Contract This Contract Shall Include All Such Items, Although Not Specifically Mentioned, That Can Be Reasonably Inferred As Being Required For Its Completion As If Such Items Were Expressly Mentioned Herein. All The Provisions Of Ra No. 9184 And Its 2016 Revised Irr, Including The Generic Procurement Manual, And Associated Issuances, Constitute The Primary Source For The Terms And Conditions Of The Contract, And Thus, Applicable In Contract Implementation. Herein Clauses Shall Serve As The Secondary Source For The Terms And Conditions Of The Contract. This Is Without Prejudice To Sections 74.1 And 74.2 Of The 2016 Revised Irr Of Ra No. 9184 Allowing The Gppb To Amend The Irr, Which Shall Be Applied To All Procurement Activities, The Advertisement, Posting, Or Invitation Of Which Were Issued After The Effectivity Of The Said Amendment. Sectional Completion Of Works If Sectional Completion Is Specified In The Special Conditions Of Contract (scc), References In The Conditions Of Contract To The Works, The Completion Date, And The Intended Completion Date Shall Apply To Any Section Of The Works (other Than References To The Completion Date And Intended Completion Date For The Whole Of The Works). Possession Of Site The Procuring Entity Shall Give Possession Of All Or Parts Of The Site To The Contractor Based On The Schedule Of Delivery Indicated In The Scc, Which Corresponds To The Execution Of The Works. If The Contractor Suffers Delay Or Incurs Cost From Failure On The Part Of The Procuring Entity To Give Possession In Accordance With The Terms Of This Clause, The Procuring Entity’s Representative Shall Give The Contractor A Contract Time Extension And Certify Such Sum As Fair To Cover The Cost Incurred, Which Sum Shall Be Paid By Procuring Entity. If Possession Of A Portion Is Not Given By The Above Date, The Procuring Entity Will Be Deemed To Have Delayed The Start Of The Relevant Activities. The Resulting Adjustments In Contract Time To Address Such Delay May Be Addressed Through Contract Extension Provided Under Annex “e” Of The 2016 Revised Irr Of Ra No. 9184. The Contractor’s Obligations The Contractor Shall Employ The Key Personnel Named In The Schedule Of Key Personnel Indicating Their Designation, In Accordance With Itb Clause 10.3 And Specified In The Bds, To Carry Out The Supervision Of The Works. The Procuring Entity Will Approve Any Proposed Replacement Of Key Personnel Only If Their Relevant Qualifications And Abilities Are Equal To Or Better Than Those Of The Personnel Listed In The Schedule. Performance Security Within Ten (10) Calendar Days From Receipt Of The Notice Of Award From The Procuring Entity But In No Case Later Than The Signing Of The Contract By Both Parties, The Successful Bidder Shall Furnish The Performance Security In Any Of The Forms Prescribed In Section 39 Of The 2016 Revised Irr. The Contractor, By Entering Into The Contract With The Procuring Entity, Acknowledges The Right Of The Procuring Entity To Institute Action Pursuant To Ra No. 3688 Against Any Subcontractor Be They An Individual, Firm, Partnership, Corporation, Or Association Supplying The Contractor With Labor, Materials And/or Equipment For The Performance Of This Contract. Site Investigation Reports The Contractor, In Preparing The Bid, Shall Rely On Any Site Investigation Reports Referred To In The Scc Supplemented By Any Information Obtained By The Contractor. Warranty In Case The Contractor Fails To Undertake The Repair Works Under Section 62.2.2 Of The 2016 Revised Irr, The Procuring Entity Shall Forfeit Its Performance Security, Subject Its Property(ies) To Attachment Or Garnishment Proceedings, And Perpetually Disqualify It From Participating In Any Public Bidding. All Payables Of The Gop In His Favor Shall Be Offset To Recover The Costs. The Warranty Against Structural Defects/failures, Except That Occasioned-on Force Majeure, Shall Cover The Period From The Date Of Issuance Of The Certificate Of Final Acceptance By The Procuring Entity. Specific Duration Of The Warranty Is Found In The Scc. Liability Of The Contractor Subject To Additional Provisions, If Any, Set Forth In The Scc, The Contractor’s Liability Under This Contract Shall Be As Provided By The Laws Of The Republic Of The Philippines. If The Contractor Is A Joint Venture, All Partners To The Joint Venture Shall Be Jointly And Severally Liable To The Procuring Entity. Termination For Other Causes Contract Termination Shall Be Initiated In Case It Is Determined Prima Facie By The Procuring Entity That The Contractor Has Engaged, Before, Or During The Implementation Of The Contract, In Unlawful Deeds And Behaviors Relative To Contract Acquisition And Implementation, Such As, But Not Limited To Corrupt, Fraudulent, Collusive, Coercive, And Obstructive Practices As Stated In Itb Clause 4. Dayworks Subject To The Guidelines On Variation Order In Annex “e” Of The 2016 Revised Irr Of Ra No. 9184, And If Applicable As Indicated In The Scc, The Dayworks Rates In The Contractor’s Bid Shall Be Used For Small Additional Amounts Of Work Only When The Procuring Entity’s Representative Has Given Written Instructions In Advance For Additional Work To Be Paid For In That Way. Program Of Work The Contractor Shall Submit To The Procuring Entity’s Representative For Approval The Said Program Of Work Showing The General Methods, Arrangements, Order, And Timing For All The Activities In The Works. The Submissions Of The Program Of Work Are Indicated In The Scc. The Contractor Shall Submit To The Procuring Entity’s Representative For Approval An Updated Program Of Work At Intervals No Longer Than The Period Stated In The Scc. If The Contractor Does Not Submit An Updated Program Of Work Within This Period, The Procuring Entity’s Representative May Withhold The Amount Stated In The Scc From The Next Payment Certificate And Continue To Withhold This Amount Until The Next Payment After The Date On Which The Overdue Program Of Work Has Been Submitted. Instructions, Inspections And Audits The Contractor Shall Permit The Gop Or The Procuring Entity To Inspect The Contractor’s Accounts And Records Relating To The Performance Of The Contractor And To Have Them Audited By Auditors Of The Gop Or The Procuring Entity, As May Be Required. Advance Payment The Procuring Entity Shall, Upon A Written Request Of The Contractor Which Shall Be Submitted As A Contract Document, Make An Advance Payment To The Contractor In An Amount Not Exceeding Fifteen Percent (15%) Of The Total Contract Price, To Be Made In Lump Sum, Or At The Most Two Installments According To A Schedule Specified In The Scc, Subject To The Requirements In Annex “e” Of The 2016 Revised Irr Of Ra No. 9184. Progress Payments The Contractor May Submit A Request For Payment For Work Accomplished. Such Requests For Payment Shall Be Verified And Certified By The Procuring Entity’s Representative/project Engineer. Except As Otherwise Stipulated In The Scc, Materials And Equipment Delivered On The Site But Not Completely Put In Place Shall Not Be Included For Payment. Operating And Maintenance Manuals If Required, The Contractor Will Provide “as Built” Drawings And/or Operating And Maintenance Manuals As Specified In The Scc. If The Contractor Does Not Provide The Drawings And/or Manuals By The Dates Stated Above, Or They Do Not Receive The Procuring Entity’s Representative’s Approval, The Procuring Entity’s Representative May Withhold The Amount Stated In The Scc From Payments Due To The Contractor. Section V. Special Conditions Of Contract Gcc Clause 2 As Per Construction Schedule/contract Period 3.1 The Procuring Entity Shall Give Possession Of All Parts Of The Site To The Contractor Upon Effectivity Of The Contracts. 6 No Further Instructions 7.2 [in Case Of Permanent Structures, Such As Buildings Of Types 4 And 5 As Classified Under The National Building Code Of The Philippines And Other Structures Made Of Steel, Iron, Or Concrete Which Comply With Relevant Structural Codes (e.g., Dpwh Standard Specifications), Such As, But Not Limited To, Steel/concrete Bridges, Flyovers, Aircraft Movement Areas, Ports, Dams, Tunnels, Filtration And Treatment Plants, Sewerage Systems, Power Plants, Transmission And Communication Towers, Railway System, And Other Similar Permanent Structures:] Fifteen (15) Years. 10 Dayworks Are Applicable At The Rate Shown In The Contractor’s Original Bid. 11.1 No Further Instructions 11.2 No Further Instructions 13 The Amount Of The Advance Shall Not Exceed 15% Of The Total Contract Price. 14 Materials And Equipment Delivered On The Site But Not Completely Installed Or Constructed Shall Not Be Included For Payment. 15.1 The Date By Which Operating And Maintenance Manuals Are Required Shall Be At Least 5 Days Before The Testing And Commissioning. The Date By Which “as Built” Drawings Are Required Prior To The Final Billing. 15.2 The Amount To Be Withheld For Failing To Produce “as Built” Drawings And/or Operating And Maintenance Manuals By The Date Required Is 1% Of The Final Contract Amount. Section Vi. Specification Scope Of Works The Works Include Furnishing Of Labor, Materials, Tools, Equipment And Other Incidentals Necessary To Complete The Project Such As: Clearing, Grubbing, And Staking, Excavation Works, Backfill, Concrete Works (concreting, Gravel Bedding, Steel Works, And Formworks), Masonry Works, And Plastering Works. Other General Requirements B.4 - Construction Survey And Staking B.4.1 Description This Item Shall Consist Of Furnishing The Necessary Equipment And Material To Survey, Stake, Calculate, And Record Data For The Control Of Work In Accordance With This Specification And In Conformity With The Lines, Grades And Dimensions Shown On The Plans Or As Established By The Engineer. B.4.2 Construction Requirements B.4.2.1 General Staking Activities Shall Be Included In The Construction Schedule To Be Submitted By The Contractor. Dates And Sequence Of Each Staking Activity Shall Be Included. The Engineer Shall Set Initial Reference Lines, Horizontal And Vertical Control Points, And Shall Furnish The Data For Use In Establishing Control For The Completion Of Each Element Of The Work. Data Relating To Horizontal And Vertical Alignments, Theoretical Slope Stake Catch Points, And Other Design Data Shall Be Furnished. The Contractor Shall Be Responsible For The True Settling Of The Works Or Improvements And For Correctness Of Positions, Levels, Dimensions And Alignment Of All Parts Of The Works. He Shall Provide All Necessary Instruments, Appliances, Materials And Supplies, And Labor In Connection Therewith. The Contractor Shall Provide A Survey Crew Supervisor At The Project Site Whenever Surveying/staking Activity Is In Progress. Prior To Construction, The Engineer Shall Be Notified Of Any Missing Initial Reference Lines, Controls, Points, Or Stakes. The Engineer Shall Reestablish Missing Initial Reference Lines, Controls, Points, Or Stakes. The Contractor For Convenient Use Of Government-furnished Data Shall Perform Additional Calculations. Immediate Notification Of Apparent Errors In The Initial Staking Or In The Furnished Data Shall Be Provided. All Initial Reference And Control Points Shall Be Preserved. At The Start Of Construction, All Destroyed Or Disturbed Initial Reference Or Control Points Necessary To The Work Shall Be Replaced. Before Surveying And Staking, The Contractor Shall Discuss And Coordinate The Following With The Engineer: 1. Surveying And Staking Methods 2. Stake Marking/concrete Monuments 3. Grade Control For Courses Of Material 4. Referencing 5. Structure Control 6. Any Other Procedures And Controls Necessary For The Work Established Controls Shall Be Within The Tolerances Shown In Table 1. Table 1: Construction Survey And Staking Tolerances (1) Staking Phase Horizontal Vertical Existing Government Network Control Points ±20mm ±8mm X √k ² Local Supplemental Control Points Set From Existing Government Network Points ±10mm ±3mm X √n³ Centerline Points (4) - (pc), (pt), (pot), And (pac) Including References ±10mm ±10mm Other Centerline Points ±50mm ±50mm Cross-section Points And Slope Stakes (5) ±50mm ±50mm Slope Stakes References ±50mm ±50mm Culverts, Ditches, And Minor Drainage Structures ±50mm ±20mm Retaining Walls And Curb And Gutter ±20mm ±10mm Bridge Substructures ±10mm (6) ±10mm Bridge Superstructures ±10mm (6) ±10mm Clearing And Grubbing Limits ±500mm Roadway Subgrade Finish Stakes (7) ±50mm ±10mm Roadway Finish Grade Stakes (7) ±50mm ±10mm (1) At 95% Confidence Level. Tolerances Are Relative To Existing Government Network Control Points. (2) K Is The Distance In Kilometers. (3) N Is The Number Of Instrument Setups. (4) Centerline Points: Pc - Point Of Curve, Pt - Point Of Tangent, Pot - Point On Tangent, Poc - Point On Curve (5) Take The Cross-sections Normal To The Centerline + 1 Degree. (6) Bridge Control Is Established As Local Network And The Tolerances Are Relative To That Network. (7) Include Pave Ditches. The Contractor Shall Prepare Field Notes In An Approved Format. All Field Notes And Supporting Documentation Shall Become The Property Of The Government Upon Completion Of The Work. Work Shall Only Be Started After Staking For The Affected Work Is Accepted. The Construction Survey And Staking Work May Be Spot-checked By The Engineer For Accuracy, And Unacceptable Portions Of Work May Be Rejected. Rejected Work Shall Be Resurveyed, And Work That Is Not Within The Tolerances Specified In Table 1 Shall Be Corrected. Acceptance Of The Construction Staking Shall Not Relieve The Contractor Of Responsibility For Correcting Errors Discovered During The Work And For Bearing All Additional Costs Associated With The Error, Unless Such Error Is Based On Incorrect Data Supplied In Writing By The Engineer, In Which Case, The Expense In Rectifying The Same Shall Be At The Expense Of The Government. In The Case Of "change" Or "changed Conditions" Which Involve Any Change In Stakeout, The Contractor Shall Coordinate With The Engineer And Facilitate The Prompt Reestablishment Of The Field Control For The Altered Or Adjusted Work. All Flagging, Lath, Stakes, And Other Staking Materials Shall Be Removed And Disposed After The Project Is Completed. B.4.2.2 Equipment Survey Instruments And Supporting Equipment Capable Of Achieving The Specified Tolerances Shall Be Furnished. Acceptable Tools, Supplies, And Stakes Of The Type And Quality Normally Used In Highway Survey Work And Suitable For The Intended Use Shall Be Furnished. Stakes And Hubs Of Sufficient Length To Provide A Solid Set In The Ground With Sufficient Surface Area Above Ground For Necessary Legible Markings Shall Also Be Furnished. B.4.2.3 Survey And Staking Requirements All Survey, Staking, Recording Of Data, And Calculations Necessary To Construct The Project From The Initial Layout To Final Completion Shall Be Performed. Stakes Shall Be Reset As Many Times As Necessary To Construct The Work. 1. Control Points Established Initial Horizontal And Vertical Control Points In Conflict With Construction Shall Be Relocated To Areas That Will Not Be Disturbed By Construction Operations. The Coordinates And Elevations For The Relocated Points Shall Be Furnished Before The Initial Points Are Disturbed. 2. Roadway Cross-sections Roadway Cross-sections Shall Be Taken Normal Or Perpendicular To The Centerline. When The Centerline Horizontal Curve Radius Is Less Than Or Equal To 150 Meters And Vertical Parabolic Curve Radius Is Less Than Or Equal To 100 Meters, Cross-sections Shall Be Taken At A Maximum Centerline Spacing Of 10 Meters. When The Centerline Horizontal Curve Radius Is Greater Than 150 Meters And Vertical Parabolic Curve Radius Is Greater Than 100 Meters, Cross-sections Shall Be Taken At A Maximum Centerline Spacing Of 20 Meters. Additional Cross-sections Shall Be Taken At Significant Breaks In Topography And At Changes In The Typical Roadway Section Including Transition Change To Super Elevated Sections. Along Each Cross-section, Points Shall Be Measured And Recorded At Breaks In Topography And At Changes In Typical Roadway Section Including Transition Change To Super Elevated Sections And Shall Be No Further Apart Than 5 Meters. Points Shall Be Measured And Recorded To At Least The Anticipated Slope Stake And Reference Locations. All Cross-section Distances Shall Be Reduced To Horizontal Distances From Centerline. 3. Slope Stakes And References Slope Stakes And References Shall Be Set On Both Sides Of Centerline At The Cross-section Locations. Slope Stakes Shall Be Established In The Field As The Actual Point Of Intersection Of The Design Roadway Slope With The Natural Ground Line. Slope Stake References Shall Be Set Outside The Clearing Limits. All Reference Point And Slope Stake Information Shall Be Included On The Reference Stakes. When Initial References Are Provided, Slope Stakes May Be Set From These Points With Verification Of The Slope Stake Location With Field Measurements. Slope Stakes On Any Section That Do Not Match With The Staking Report Within The Tolerances Established In Table 1 Shall Be Recatched. Roadway Cross-section Data Shall Be Taken Between Centerline And The New Slope Stake Location. Additional References Shall Be Set Even When The Initial References Are Provided. 4. Clearing And Grubbing Limits Clearing And Grubbing Limits Shall Be Set On Both Sides Of Centerline At Roadway Cross-section Locations, Extending One (1) Meter Beyond The Toe Of The Fill Slopes Or Beyond Rounding Of Cut Slopes As The Case Maybe For The Entire Length Of The Project Unless Otherwise Shown On The Plans Or As Directed By The Engineer. 5. Centerline Reestablishment Centerline Shall Be Reestablished From Instrument Control Points. The Maximum Spacing Between Centerline Points Shall Be 10 Meters When The Centerline Horizontal Curve Radius Is Less Than Or Equal To 150 Meters And Vertical Parabolic Curve Radius Is Less Than Or Equal To 100 Meters. When The Centerline Horizontal Curve Radius Is Greater Than 150 Meters And Vertical Parabolic Curve Radius Is Greater Than 100 Meters, The Maximum Distance Between Centerline Points Shall Be 20 Meters. 6. Grade Finishing Stakes Grade Finishing Stakes Shall Be Set For Grade Elevations And Horizontal Alignment, At The Centerline And At Each Shoulder Of Roadway Cross-section Locations. Stakes Shall Be Set At The Top Of Subgrade And The Top Of Each Aggregate Course. Where Turnouts Are Constructed, Stakes Shall Be Set At The Centerline, At Each Normal Shoulder, And At The Shoulder Of The Turnout. In Parking Areas, Hubs Shall Be Set At The Center And Along The Edges Of The Parking Area. Stakes Shall Be Set At All Ditches To Be Paved. The Maximum Longitudinal Spacing Between Stakes Shall Be 10 Meters When The Centerline Horizontal Curve Radius Is Less Than Or Equal To 150 Meters And Vertical Parabolic Curve Radius Is Less Than Or Equal To 100 Meters. When The Centerline Horizontal Curve Radius Is Greater Than 150 Meters And Vertical Parabolic Curve Radius Is Greater Than 100 Meters, The Maximum Longitudinal Spacing Between Stakes Shall Be 20 Meters. The Maximum Transverse Spacing Between Stakes Shall Be 5 Meters. Brushes Or Guard Stakes Shall Be Used At Each Stake. 7. Culverts Culverts Shall Be Staked To Fit Field Conditions. The Location Of Culverts May Differ From The Plans. The Following Shall Be Performed: A. Survey And Record The Ground Profile Along The Culvert Centerline Including Inlet And Outlet Channel Profile Of At Least 10 Meters And As Additionally Directed By The Engineer So As To Gather All Necessary Data For The Preparation Of Pipe Projection Plan. B. Determine The Slope Catch Points At The Inlet And Outlet. C. Set The Reference Points And Record Information Necessary To Determine Culvert Length And End Treatments. D. Plot Into Scale The Profile Along The Culvert Centerline Reflecting The Natural Ground Elevation, Invert Elevation, The Flow Line, The Roadway Section, And The Size, Length And The Degree Of Elbow Of Culvert, End Treatments, Grade And Other Appurtenances. E. Plot Into Scale The Cross-section Of Inlet And Outlet Channel At Not More Than 5 Meters Interval. F. Submit The Plotted Pipe Projection Plan For Approval Of Final Culvert Length, Alignment And Headwall. G. When The Pipe Projection Plan Has Been Approved, Set Drainage Culvert Structure Survey And Reference Stakes, And Stake Inlet And Outlet To Make The Structure Functional. 8. Retaining Walls And Other Types Of Slope Protection Works Profile Measurements Along The Face Of The Proposed Wall And 2 Meters In Front Of The Wall Face Shall Be Surveyed And Recorded. Cross-sections Shall Be Taken Within The Limits Designated By The Engineer At Every 5 Meters Along The Length Of The Wall And All Major Breaks In Terrain. For Each Cross-section, Points Shall Be Measured And Recorded Every 5 Meters And At All Major Breaks In Terrain. Adequate References And Horizontal And Vertical Control Points Shall Be Set. 9. Borrow And Waste Sites The Work Essential For Initial Layout And Measurement Of The Borrow Or Waste Site Shall Be Performed. A Referenced Baseline, Site Limits, And Clearing Limits Shall Be Established. Initial And Final Cross-sections Shall Be Surveyed And Recorded. 10. Permanent Monuments And Markers All Survey And Staking Necessary To Establish Permanent Monuments And Markers Shall Be Performed. 11. Miscellaneous Survey And Staking All Surveying, Staking, And Recording Of Data Essential For Establishing The Layout And Control Of The Following Shall Be Performed, As Applicable: A. Approach Roads And Trails B. Road Right Of Way And Construction Limit In Accordance With The Approved Parcellary Plan. C. Curb And Gutter D. Guardrail E. Parking Areas F. Paved Waterways And Outfall Structures G. Lined Canals And Other Ditches H. Chutes And Spillways I. Turf Establishment-s J. Utilities K. Signs, Delineators, And Object 9 Markers I. Pavement Markings B.4.3 Method Of Measurement Construction Survey And Staking Shall Be Measured By The Kilometer. Slope, Reference, And Clearing And Grubbing Stakes Shall Be Measured By The Kilometer. Centerline Establishment Shall Be Measured By The Kilometer. Centerline Reestablishment Shall Be Measured Only One Time. Culvert Survey And Staking Shall Be Measured By The Each. Grade Finishing Stakes Shall Be Measured By The Kilometer. Subgrade Shall Be Measured One Time And Each Aggregate Course Shall Also Be Measured One Time. Permanent Monuments And Markers Shall Be Measured By Each Unit Placed And Installed At The Proper Locations. Miscellaneous Survey And Staking Shall Be Measured By The Hour Of Survey Work Ordered Or By The Lump Sum. For Miscellaneous Survey And Staking Paid By The Hour, The Minimum Survey Crew Size Shall Be 2 Persons. Time Spent In Making Preparations, Travelling To And From The Project Site, Performing Calculations, Plotting Cross Sections And Other Data, Processing Computer Data, And Other Efforts Necessary To Successfully Accomplish Construction Survey And Staking Shall Not Be Measured Separately But Deemed Included As Subsidiary For Each Of The Pay Item. Project Sign Board / Billboard The Contractor Shall Ensure That The Project Site Is Identified With Information Billboard Which Shall Be Erected At The Beginning And Ending Of The Proposed Project. The Layout Of The Billboard Shall Accord To The Specifications Pursuant To The Commission On Audit (coa) Circular No. 2013-004 Issued On January 30, 2013. Coa Billboard Pao Billboard The Billboard’s Specifications Shall Conform To The Following Requirements: Tarpaulin, White, 8ft X 8ft (coa) And 4ft X 8ft (pao): Resolution: 70 Dpi; Font: Helvetica; Font Size: Main Information – 3”; Sub-information – 1”; Font Color: Black; Suitable Frame: Rigid Wood Or Steel Frame With Post; And, Posting: Outside Display At The Project Location After Award Has Been Made. Measurement The Supply And Erection Of Project Billboard Shall Be In Accordance With Provisions Of This Specification And Shall Be Measured For Payment. Basis Of Payment Payment Shall Be In Accordance With All The Cost Associated With The Compliance Of This Specification And Shall Be Included In The Contractor’s Bid Price. No Additional Or Separate Payment Will Be Made In This Regard As Well As For The Maintenance Of The Billboard. Pay Item Number Description Unit Of Measurement B.5 Project Billboard Each Part C – Earthwork Item 100 – Clearing And Grubbing 100.1 Description This Item Shall Consist Of Clearing, Grubbing, Removing And Disposing All Vegetation And Debris As Designated In The Contract, Except Those Objects That Are Designated To Remain In Place Or Are To Be Removed In Consonance With Other Provisions Of This Specification. The Work Shall Also Include The Preservation From Injury Or Defacement Of All Objects Designated To Remain. 100.2 Construction Requirements 100.2.1 General The Engineer Will Establish The Limits Of Work And Designate All Trees, Shrubs, Plants And Other Things To Remain. The Contractor Shall Preserve All Objects Designated To Remain. Paint Required For Cut Or Scarred Surface Of Trees Or Shrubs Selected For Retention Shall Be An Approved Asphaltum Base Paint Prepared Especially For Tree Surgery. Clearing Shall Extend One (1) Meter Beyond The Toe Of The Fill Slopes Or Beyond Rounding Of Cut Slopes As The Case Maybe For The Entire Length Of The Project Unless Otherwise Shown On The Plans Or As Directed By The Engineer And Provided It Is Within The Right Of Way Limits Of The Project, With The Exception Of Trees Under The Jurisdiction Of The Forest Management Bureau (fmb). 100.2.2 Clearing And Grubbing All Surface Objects And All Trees, Stumps, Roots And Other Protruding Obstructions, Not Designated To Remain, Shall Be Cleared And/or Grubbed, Including Mowing As Required, Except As Provided Below: (1) Removal Of Undisturbed Stumps And Roots And Nonperishable Solid Objects With A Minimum Depth Of One (1) Meter Below Subgrade Or Slope Of Embankment Will Not Be Required. (2) In Areas Outside Of The Grading Limits Of Cut And Embankment Areas, Stumps And Nonperishable Solid Objects Shall Be Cut Off Not More Than 150 Mm (6 Inches) Above The Ground Line Or Low Water Level. (3) In Areas To Be Rounded At The Top Of Cut Slopes, Stumps Shall Be Cut Off Flush With Or Below The Surface Of The Final Slope Line. (4) Grubbing Of Pits, Channel Changes And Ditches Will Be Required Only To The Depth Necessitated By The Proposed Excavation Within Such Areas. (5) In Areas Covered By Cogon/talahib, Wild Grass And Other Vegetations, Top Soil Shall Be Cut To A Maximum Depth Of 150 Mm Below The Original Ground Surface Or As Designated By The Engineer, And Disposed Outside The Clearing And Grubbing Limits As Indicated In The Typical Roadway Section. Except In Areas To Be Excavated, Stump Holes And Other Holes From Which Obstructions Are Removed Shall Be Backfilled With Suitable Material And Compacted To The Required Density. If Perishable Material Is Burned, It Shall Be Burned Under The Constant Care Of Component Watchmen At Such Times And In Such A Manner That The Surrounding Vegetation, Other Adjacent Property, Or Anything Designated To Remain On The Right Of Way Will Not Be Jeopardized. If Permitted, Burning Shall Be Done In Accordance With Applicable Laws, Ordinances, And Regulation. The Contractor Shall Use High Intensity Burning Procedures, (i.e., Incinerators, High Stacking Or Pit And Ditch Burning With Forced Air Supplements) That Produce Intense Burning With Little Or No Visible Smoke Emission During The Burning Process. At The Conclusion Of Each Burning Session, The Fire Shall Be Completely Extinguished So That No Smoldering Debris Remains. In The Event That The Contractor Is Directed By The Engineer Not To Start Burning Operations Or To Suspend Such Operations Because Of Hazardous Weather Conditions, Material To Be Burned Which Interferes With Subsequent Construction Operations Shall Be Moved By The Contractor To Temporary Locations Clear Of Construction Operations And Later, If Directed By The Engineer, Shall Be Placed On A Designated Spot And Burned. Materials And Debris Which Cannot Be Burned And Perishable Materials May Be Disposed Off By Methods And At Locations Approved By The Engineer, On Or Off The Project. If Disposal Is By Burying, The Debris Shall Be Placed In Layers With The Material So Disturbed To Avoid Nesting. Each Layer Shall Be Covered Or Mixed With Earth Material By The Land-fill Method To Fill All Voids. The Top Layer Of Material Buried Shall Be Covered With At Least 300 Mm (12 Inches) Of Earth Or Other Approved Material And Shall Be Graded, Shaped And Compacted To Present A Pleasing Appearance. If The Disposal Location Is Off The Project, The Contractor Shall Make All Necessary Arrangements With Property Owners In Writing For Obtaining Suitable Disposal Locations Which Are Outside The Limits Of View From The Project. The Cost Involved Shall Be Included In The Unit Bid Price. A Copy Of Such Agreement Shall Be Furnished To The Engineer. The Disposal Areas Shall Be Seeded, Fertilized And Mulched At The Contractor’s Expense. Woody Material May Be Disposed Off By Chipping. The Wood Chips May Be Used For Mulch, Slope Erosion Control Or May Be Uniformly Spread Over Selected Areas As Directed By The Engineer. Wood Chips Used As Mulch For Slope Erosion Control Shall Have A Maximum Thickness Of 12 Mm (1/2 Inch) And Faces Not Exceeding 3900 Mm2 (6 Square Inches) On Any Individual Surface Area. Wood Chips Not Designated For Use Under Other Sections Shall Be Spread Over The Designated Areas In Layers Not To Exceed 75 Mm (3 Inches) Loose Thickness. Diseased Trees Shall Be Buried Or Disposed Off As Directed By The Engineer. All Merchantable Timber In The Clearing Area Which Has Not Been Removed From The Right Of Way Prior To The Beginning Of Construction, Shall Become The Property Of The Contractor, Unless Otherwise Provided. Low Hanging Branches And Unsound Or Unsightly Branches On Trees Or Shrubs Designated To Remain Shall Be Trimmed As Directed. Branches Of Trees Extending Over The Roadbed Shall Be Trimmed To Give A Clear Height Of 6 M (20 Feet) Above The Roadbed Surface. All Trimming Shall Be Done By Skilled Workmen And In Accordance With Good Tree Surgery Practices. Timber Cut Inside The Area Staked For Clearing Shall Be Felled Within The Area To Be Cleared. 100.2.3 Individual Removal Of Trees Or Stumps Individual Trees Or Stumps Designated By The Engineer For Removal And Located In Areas Other Than Those Established For Clearing And Grubbing And Roadside Cleanup Shall Be Removed And Disposed Off As Specified Under Subsection 100.2.2 Except Trees Removed Shall Be Cut As Nearly Flush With The Ground As Practicable Without Removing Stumps. 100.3 Method Of Measurement Measurement Will Be By One Or More Of The Following Alternate Methods: 1. Area Basis. The Work To Be Paid For Shall Be The Number Of Hectares And Fractions Thereof Acceptably Cleared And Grubbed Within The Limits Indicated On The Plans Or As May Be Adjusted In Field Staking By The Engineer. Areas Not Within The Clearing And Grubbing Limits Shown On The Plans Or Not Staked For Clearing And Grubbing Will Not Be Measured For Payment. 2. Lump-sum Basis. When The Bill Of Quantities Contains A Clearing And Grubbing Lump-sum Item, No Measurement Of Area Will Be Made For Such Item. 3. Individual Unit Basis (selective Clearing). The Diameter Of Trees Will Be Measured At A Height Of 1.4 M (54 Inches) Above The Ground. Trees Less Than 150 Mm (6 Inches) In Diameter Will Not Be Measured For Payment. When Bill Of Quantities Indicates Measurement Of Trees By Individual Unit Basis, The Units Will Be Designated And Measured In Accordance With The Following Schedule Of Sizes: Diameter At Height Of 1.4 M Pay Item Designation Over 150 Mm To 900 Mm Small Over 900 Mm Large 100.4 Basis Of Payment The Accepted Quantities, Measured As Prescribed In Section 100.3, Shall Be Paid For At The Contract Unit Price For Each Of The Pay Items Listed Below That Is Included In The Bill Of Quantities, Which Price And Payment Shall Be Full Compensation For Furnishing All Labor, Equipment, Tools And Incidentals Necessary To Complete The Work Prescribed In This Item. Payment Will Be Made Under: Pay Item Number Description Unit Of Measurement 100 (1) Clearing And Grubbing Hectare 100 (2) Clearing And Grubbing Lump Sum 100 (3) Individual Removal Of Trees, Small Each 100 (4) Individual Removal Of Trees, Large Each Item 103 - Structure Excavation 103.1 Description This Item Shall Consist Of The Necessary Excavation For Foundation Of Bridges, Culverts, Underdrains, And Other Structures Not Otherwise Provided For In The Specifications. Except As Otherwise Provided For Pipe Culverts, The Backfilling Of Completed Structures And The Disposal Of All Excavated Surplus Materials, Shall Be In Accordance With These Specifications And In Reasonably Close Conformity With The Plans Or As Established By The Engineer. This Item Shall Include Necessary Diverting Of Live Streams, Bailing, Pumping, Draining, Sheeting, Bracing, And The Necessary Construction Of Cribs And Cofferdams, And Furnishing The Materials Therefore, And The Subsequent Removal Of Cribs And Cofferdams And The Placing Of All Necessary Backfill. It Shall Also Include The Furnishing And Placing Of Approved Foundation Fill Material To Replace Unsuitable Material Encountered Below The Foundation Elevation Of Structures. No Allowance Will Be Made For Classification Of Different Types Of Material Encountered. 103.2 Construction Requirements 103.2.1 Clearing And Grubbing Prior To Starting Excavation Operations In Any Area, All Necessary Clearing And Grubbing In That Area Shall Have Been Performed In Accordance With Item 100, Clearing And Grubbing. 103.2.2 Excavation (1) General, All Structures. The Contractor Shall Notify The Engineer Sufficiently In Advance Of The Beginning Of Any Excavation So That Cross-sectional Elevations And Measurements May Be Taken On The Undisturbed Ground. The Natural Ground Adjacent To The Structure Shall Not Be Disturbed Without Permission Of The Engineer. Trenches Or Foundation Pits For Structures Or Structure Footings Shall Be Excavated To The Lines And Grades Or Elevations Shown On The Plans Or As Staked By The Engineer. They Shall Be Of Sufficient Size To Permit The Placing Of Structures Or Structure Footings Of The Full Width And Length Shown. The Elevations Of The Bottoms Of Footings, As Shown On The Plans, Shall Be Considered As Approximate Only And The Engineer May Order, In Writing, Such Changes In Dimensions Or Elevations Of Footings As May Be Deemed Necessary, To Secure A Satisfactory Foundation. Boulders, Logs, And Other Objectionable Materials Encountered In Excavation Shall Be Removed. After Each Excavation Is Completed, The Contractor Shall Notify The Engineer To That Effect And No Footing, Bedding Material Or Pipe Culvert Shall Be Placed Until The Engineer Has Approved The Depth Of Excavation And The Character Of The Foundation Material. (2) Structures Other Than Pipe Culverts. All Rock Or Other Hard Foundation Materials Shall Be Cleaned Of All Loose Materials, And Cut To A Firm Surface, Either Level, Stepped, Or Serrated As Directed By The Engineer. All Seams Or Crevices Shall Be Cleaned And Grouted. All Loose And Disintegrated Rocks And Thin Strata Shall Be Removed. When The Footing Is To Rest On Material Other Than Rock, Excavation To Final Grade Shall Not Be Made Until Just Before The Footing Is To Be Placed. When The Foundation Material Is Soft Or Mucky Or Otherwise Unsuitable, As Determined By The Engineer, The Contractor Shall Remove The Unsuitable Material And Backfill With Approved Granular Material. This Foundation Fill Shall Be Placed And Compacted In 150 Mm Layers Up To The Foundation Elevation. When Foundation Piles Are Used, The Excavation Of Each Pit Shall Be Completed Before The Piles Are Driven And Any Placing Of Foundation Fill Shall Be Done After The Piles Are Driven. After The Driving Is Completed, All Loose And Displaced Materials Shall Be Removed, Leaving A Smooth, Solid Bed To Receive The Footing. (3) Pipe Culverts. The Width Of The Pipe Trench Shall Be Sufficient To Permit Satisfactory Jointing Of The Pipe And Thorough Tamping Of The Bedding Material Under And Around The Pipe. Where Rock, Hardpan, Or Other Unyielding Material Is Encountered, It Shall Be Removed Below The Foundation Grade For A Depth Of At Least 300 Mm Or 4 Mm For Each 100 Mm Of Fill Over The Top Of Pipe, Whichever Is Greater, But Not To Exceed Three-quarters Of The Vertical Inside Diameter Of The Pipe. The Width Of The Excavation Shall Be At Least 300 Mm Greater Than The Horizontal Outside Diameter Of The Pipe. The Excavation Below Grade Shall Be Backfilled With Selected Fine Compressible Material, Such As Silty Clay Or Loam, And Lightly Compacted In Layers Not Over 150 Mm In Uncompacted Depth To Form A Uniform But Yielding Foundation. Where A Firm Foundation Is Not Encountered At The Grade Established, Due To Soft, Spongy, Or Other Unstable Soil, Such Unstable Soil Under The Pipe And For A Width Of At Least One Diameter On Each Side Of The Pipe Shall Be Removed To The Depth Directed By The Engineer And Replaced With Approved Granular Foundation Fill Material Properly Compacted To Provide Adequate Support For The Pipe, Unless Other Special Construction Methods Are Called For On The Plans. The Foundation Surface Shall Provide A Firm Foundation Of Uniform Density Throughout The Length Of The Culvert And If Directed By The Engineer, Shall Be Cambered In The Direction Parallel To The Pipe Centerline. Where Pipe Culverts Are To Be Placed In Trenches Excavated In Embankments, The Excavation Of Each Trench Shall Be Performed After The Embankment Has Been Constructed To A Plane Parallel To The Proposed Profile Grade And To Such Height Above The Bottom Of The Pipe As Shown On The Plans Or Directed By The Engineer. 103.2.3 Utilization Of Excavated Materials All Excavated Materials, So Far As Suitable, Shall Be Utilized As Backfill Or Embankment. The Surplus Materials Shall Be Disposed Of In Such Manner As Not To Obstruct The Stream Or Otherwise Impair The Efficiency Or Appearance Of The Structure. No Excavated Materials Shall Be Deposited At Any Time So As To Endanger The Partly Finished Structure. 103.2.4 Cofferdams Suitable And Practically Watertight Cofferdams Shall Be Used Wherever Water-bearing Strata Are Encountered Above The Elevation Of The Bottom Of The Excavation. If Requested, The Contractor Shall Submit Drawings Showing His Proposed Method Of Cofferdam Construction, As Directed By The Engineer. Cofferdams Or Cribs For Foundation Construction Shall In General, Be Carried Well Below The Bottoms Of The Footings And Shall Be Well Braced And As Nearly Watertight As Practicable. In General, The Interior Dimensions Of Cofferdams Shall Be Such As To Give Sufficient Clearance For The Construction Of Forms And The Inspection Of Their Exteriors, And To Permit Pumping Outside Of The Forms. Cofferdams Or Cribs Which Are Tilted Or Moved Laterally During The Process Of Sinking Shall Be Righted Or Enlarged So As To Provide The Necessary Clearance. When Conditions Are Encountered Which, As Determined By The Engineer, Render It Impracticable To Dewater The Foundation Before Placing The Footing, The Engineer May Require The Construction Of A Concrete Foundation Seal Of Such Dimensions As He May Consider Necessary, And Of Such Thickness As To Resist Any Possible Uplift. The Concrete For Such Seal Shall Be Placed As Shown On The Plans Or Directed By The Engineer. The Foundation Shall Then Be Dewatered And The Footing Placed. When Weighted Cribs Are Employed And The Mass Is Utilized To Overcome Partially The Hydrostatic Pressure Acting Against The Bottom Of The Foundation Seal, Special Anchorage Such As Dowels Or Keys Shall Be Provided To Transfer The Entire Mass Of The Crib To The Foundation Seal. When A Foundation Seal Is Placed Under Water, The Cofferdams Shall Be Vented Or Ported At Low Water Level As Directed. Cofferdams Shall Be Constructed So As To Protect Green Concrete Against Damage From Sudden Rising Of The Stream And To Prevent Damage To The Foundation By Erosion. No Timber Or Bracing Shall Be Left 30 In Cofferdams Or Cribs In Such A Way As To Extend Into Substructure Masonry, Without Written Permission From The Engineer. Any Pumping That May Be Permitted From The Interior Of Any Foundation Enclosure Shall Be Done In Such A Manner As To Preclude The Possibility Of Any Portion Of The Concrete Material Being Carried Away. Any Pumping Required During The Placing Of Concrete, Or For A Period Of At Least 24 Hours Thereafter, Shall Be Done From A Suitable Sump Located Outside The Concrete Forms. Pumping To Dewater A Sealed Cofferdam Shall Not Commence Until The Seal Has Set Sufficiently To Withstand The Hydrostatic Pressure. Unless Otherwise Provided, Cofferdams Or Cribs, With All Sheeting And Bracing Involved Therewith, Shall Be Removed By The Contractor After The Completion Of The Substructure. Removal Shall Be Effected In Such Manner As Not To Disturb Or Mar Finished Masonry. 103.2.5 Preservation Of Channel Unless Otherwise Permitted, No Excavation Shall Be Made Outside Of Caissons, Cribs, Cofferdams, Or Sheet Piling, And The Natural Stream Bed Adjacent To Structure Shall Not Be Disturbed Without Permission From The Engineer. If Any Excavation Or Dredging Is Made At The Side Of The Structure Before Caissons, Cribs, Or Cofferdams Are Sunk In Place, The Contractor Shall, After The Foundation Base Is In Place, Backfill All Such Excavations To The Original Ground Surface Or Stream Bed With Material Satisfactory To The Engineer. 103.2.6 Backfill And Embankment For Structures Other Than Pipe Culverts Excavated Areas Around Structures Shall Be Backfilled With Free Draining Granular Material Approved By The Engineer And Placed In Horizontal Layers Not Over 150 Mm In Thickness, To The Level Of The Original Ground Surface. Each Layer Shall Be Moistened Or Dried As Required And Thoroughly Compacted With Mechanical Tampers. In Placing Backfills Or Embankment, The Material Shall Be Placed Simultaneously In So Far As Possible To Approximately The Same Elevation On Both Sides Of An Abutment, Pier, Or Wall. If Conditions Require Placing Backfill Or Embankment Appreciably Higher On One Side Than On The Opposite Side, The Additional Material On The Higher Side Shall Not Be Placed Until The Masonry Has Been In Place For 14 Days, Or Until Tests Made By The Laboratory Under The Supervision Of The Engineer Establishes That The Masonry Has Attained Sufficient Strength To Withstand Any Pressure Created By The Methods Used And Materials Placed Without Damage Or Strain Beyond A Safe Factor. Backfill Or Embankment Shall Not Be Placed Behind The Walls Of Concrete Culverts Or Abutments Or Rigid Frame Structures Until The Top Slab Is Placed And Cured. Backfill And Embankment Behind Abutments Held At The Top By The Superstructure, And Behind The Sidewalls Of Culverts, Shall Be Carried Up Simultaneously Behind Opposite Abutments Or Sidewalls. All Embankments Adjacent To Structures Shall Be Constructed In Horizontal Layers And Compacted As Prescribed In Subsection 104.3.3 Except That Mechanical Tampers May Be Used For The Required Compaction. Special Care Shall Be Taken To Prevent Any Wedging Action Against The Structure, And Slopes Bounding Or Within The Areas To Be Filled Shall Be Benched Or Serrated To Prevent Wedge Action. The Placing Of Embankment And The Benching Of Slopes Shall Continue In Such A Manner That At All Times There Will Be Horizontal Berm Of Thoroughly Compacted Material For A Distance At Least Equal To The Height Of The Abutment Or Wall To Be Backfilled Against Except Insofar As Undisturbed Material Obtrudes Upon The Area. Broken Rock Or Coarse Sand And Gravel Shall Be Provided For A Drainage Filter At Weepholes As Shown On The Plans. 103.2.7 Bedding, Backfill, And Embankment For Pipe Culverts Bedding, Backfill And Embankment For Pipe Culverts Shall Be Done In Accordance With Item 500, Pipe Culverts And Storm Drains. 103.3 Method Of Measurement 103.3.1 Structure Excavation The Volume Of Excavation To Be Paid For Will Be The Number Of Cubic Meters Measured In Original Position Of Material Acceptably Excavated In Conformity With The Plans Or As Directed By The Engineer, But In No Case, Except As Noted, Will Any Of The Following Volumes Be Included In The Measurement For Payment: (1) The Volume Outside Of Vertical Planes 450 Mm Outside Of And Parallel To The Neat Lines Of Footings And The Inside Walls Of Pipe And Pipe-arch Culverts At Their Widest Horizontal Dimensions. (2) The Volume Of Excavation For Culvert And Sections Outside The Vertical Plane For Culverts Stipulated In (1) Above. (3) The Volume Outside Of Neat Lines Of Underdrains As Shown On The Plans, And Outside The Limits Of Foundation Fill As Ordered By The Engineer. (4) The Volume Included Within The Staked Limits Of The Roadway Excavation, Contiguous Channel Changes, Ditches, Etc., For Which Payment Is Otherwise Provided In The Specification. (5) Volume Of Water Or Other Liquid Resulting From Construction Operations And Which Can Be Pumped Or Drained Away. (6) The Volume Of Any Excavation Performed Prior To The Taking Of Elevations And Measurements Of The Undisturbed Ground. (7) The Volume Of Any Material Rehandled, Except That Where The Plans Indicate Or The Engineer Directs The Excavation After Embankment Has Been Placed And Except That When Installation Of Pipe Culverts By The Imperfect Trench Method Specified In Item 500 Is Required, The Volume Of Material Reexcavated As Directed Will Be Included. (8) The Volume Of Excavation For Footings Ordered At A Depth More Than 1.5 M Below The Lowest Elevation For Such Footings Shown On The Original Contract Plans, Unless The Bill Of Quantities Contains A Pay Item For Excavation Ordered Below The Elevations Shown On The Plans For Individual Footings. Item 404 – Reinforcing Steel Description This Item Shall Consist Of Furnishing, Bending, Fabricating And Placing Of Steel Reinforcement Of The Type, Size, Shape And Grade Required In Accordance With This Specification And In Conformity With The Requirements Shown On The Plans Or As Directed By The Engineer. Strictly Implement The Usage Of Grade 40 Reinforcing Steel. Material Requirements Reinforcing Steel Shall Meet The Requirements Of Item 710, Reinforcing Steel And Wire Rope. Construction Requirements 404.3.1 Order Lists Before Materials Are Ordered, All Order Lists And Bending Diagrams Shall Be Furnished By The Contractor, For Approval Of The Engineer. The Approval Of Order Lists And Bending Diagrams By The Engineer Shall In No Way Relieve The Contractor Of Responsibility For The Correctness Of Such Lists And Diagrams. Any Expense Incident To The Revisions Of Materials Furnished In Accordance With Such Lists And Diagrams To Make Them Comply With The Plans Shall Be Borne By The Contractor. 404.3.2 Protection Of Material Steel Reinforcement Shall Be Stored Above The Surface Of The Ground Upon Platforms, Skids, Or Other Supports And Shall Be Protected As Far As Practicable From Mechanical Injury And Surface Deterioration Caused By Exposure To Conditions Producing Rust. When Placed In The Work, Reinforcement Shall Be Free From Dirt, Detrimental Rust, Loose Scale, Paint, Grease, Oil, Or Other Foreign Materials. Reinforcement Shall Be Free From Injurious Defects Such As Cracks And Laminations. Rust, Surface Seams, Surface Irregularities Or Mill Scale Will Not Be Cause For Rejection, Provided The Minimum Dimensions, Cross Sectional Area And Tensile Properties Of A Hand Wire Brushed Specimen Meets The Physical Requirements For The Size And Grade Of Steel Specified. Bending All Reinforcing Bars Requiring Bending Shall Be Cold-bent To The Shapes Shown On The Plans Or Required By The Engineer. Bars Shall Be Bent Around A Circular Pin Having The Following Diameters (d) In Relation To The Diameter Of The Bar (d): Nominal Diameter, D, Mm Pin Diameter (d) 10 To 20 25 To 28 32 And Greater 6d 8d 10d Bends And Hooks In Stirrups Or Ties May Be Bent To The Diameter Of The Principal Bar Enclosed Therein. Placing And Fastening All Steel Reinforcement Shall Be Accurately Placed In The Position Shown On The Plans Or Required By The Engineer And Firmly Held There During The Placing And Setting Of The Concrete. Bars Shall Be Tied At All Intersections Except Where Spacing Is Less Than 300mm In Each Directions, In Which Case, Alternate Intersections Shall Be Tied. Ties Shall Be Fastened On The Inside. Distance From The Forms Shall Be Maintained By Means Of Stays, Blocks, Ties, Hangers, Or Other Approved Supports, So That It Does Not Vary From The Position Indicated On The Plans By More Than 6mm. Blocks For Holding Reinforcement From Contact With The Forms Shall Be Precast Mortar Blocks Of Approved Shapes And Dimensions. Layers Of Bars Shall Be Separated By Precast Mortar Blocks Or By Other Equally Suitable Devices. The Use Of Pebbles, Pieces Of Broken Stone Or Brick, Metal Pipe And Wooden Blocks Shall Not Be Permitted. Unless Otherwise Shown On The Plans Or Required By The Engineer, The Minimum Distance Between Bars Shall Be 40mm. Reinforcement In Any Member Shall Be Placed And Then Inspected And Approved By The Engineer Before The Placing Of Concrete Begins. Concrete Placed In Violation Of This Provision May Be Rejected And Removal May Be Required. If Fabric Reinforcement Is Shipped In Rolls, It Shall Be Straightened Before Being Placed. Bundled Bars Shall Be Tied Together At Not More Than 1.8m Intervals. Splicing All Reinforcement Shall Be Furnished In The Full Lengths Indicated On The Plans. Splicing Of Bars, Except Where Shown On The Plans, Will Not Be Permitted Without The Written Approval Of The Engineer. Splices Shall Be Staggered As Far As Possible And With A Minimum Separation Of Not Less Than 40 Bar Diameters. Not More Than One-third Of The Bars May Be Spliced In The Same Cross-section, Except Where Shown On The Plans. Unless Otherwise Shown On The Plans, Bars Shall Be Lapped A Minimum Distance Of: Splice Type Grade 40 Min. Lap Grade 60 Min. Lap But Not Less Than Tension 24 Bar Dia 36 Bar Dia 300 Mm Compression 20 Bar Dia 24 Bar Dia 300 Mm In Lapped Splices, The Bars Shall Be Placed In Contact And Wired Together. Lapped Splices Will Not Be Permitted At Locations Where The Concrete Section Is Insufficient To Provide Minimum Clear Distance Of One And One-third The Maximum Size Of Coarse Aggregate Between The Splice And The Nearest Adjacent Bar. Welding Of Reinforcing Steel Shall Be Done Only If Detailed On The Plans Or If Authorized By The Engineer In Writing. Spiral Reinforcement Shall Be Spliced By Lapping At Least One And A Half Turns Or By Butt Welding Unless Otherwise Shown On The Plans. Lapping Of Bar Mat Sheets Of Mesh Or Bar Mat Reinforcement Shall Overlap Each Other Sufficiently To Maintain A Uniform Strength And Shall Be Securely Fastened At The Ends And Edges. The Overlap Shall Not Be Less Than One Mesh In Width. Method Of Measurement The Quantity Of Reinforcing Steel To Be Paid For Will Be The Final Quantity Placed And Accepted In The Completed Structure. No Allowance Will Be Made For Tie-wires, Separators, Wire Chairs And Other Material Used In Fastening The Reinforcing Steel In Place. If Bars Are Substituted Upon The Contractor’s Request And Approved By The Engineer And As A Result Thereof More Steel Is Used Than Specified, Only The Mass Specified Shall Be Measured For Payment. No Measurement Or Payment Will Be Made For Splices Added By The Contractor Unless Directed Or Approved By The Engineer. When There Is No Item For Reinforcing Steel In The Bill Of Quantities, Costs Will Be Considered As Incidental To The Other Items In The Bill Of Quantities. Basis Of Payment The Accepted Quantity, Measured As Prescribed In Section 404.4, Shall Be Paid For At The Contract Unit Price For Reinforcing Steel Which Price And Payment Shall Be Full Compensation For Furnishing And Placing All Materials, Including All Labor, Equipment, Tools And Incidentals Necessary To Complete The Work Prescribed In This Item. Payment Will Be Made Under: Pay Item Number Description Unit Of Measurement 404 Reinforcing Steel Kilogram Item 405 – Structural Concrete Description 405.1.1 Scope This Item Shall Consist Of Furnishing, Bending, Placing And Finishing Concrete In All Structures Except Pavements In Accordance With This Specification And Conforming To The Lines, Grades, And Dimensions Shown On The Plans. Concrete Shall Consist Of A Mixture Of Portland Cement, Fine Aggregate, Coarse Aggregate, Admixture When Specified, And Water Mixed In The Proportions Specified Or Approved By The Engineer. The Structural Strength Of Concrete Shall Be 24 Mpa. 405.1.2 Classes And Uses Of Concrete Five Classes Of Concrete Are Provided For In This Item, Namely: A, B, C, P And Seal. Each Class Shall Be Used In That Part Of The Structure As Called For On The Plans. The Classes Of Concrete Will Generally Be Used As Follows: Class A – All Superstructures And Heavily Reinforced Substructures. The Important Parts Of The Structure Included Are Slabs, Beams, Girders, Columns, Arch Ribs, Box Culverts, Reinforced Abutments, Retaining Walls, And Reinforced Footings. Class B – Footings, Pedestals, Massive Pier Shafts, Pipe Bedding, And Gravity Walls, Unreinforced Or With Only A Small Amount Of Reinforcement. Class C – Thin Reinforced Sections, Railings, Precast R.c. Piles And Cribbing And For Filler In Steel Grid Floors. Class P – Prestressed Concrete Structures And Members. Seal – Concrete Deposited In Water. Material Requirements 405.2.1 Portland Cement It Shall Conform To All The Requirements Of Subsection 311.2.1. Fine Aggregate It Shall Conform To All The Requirements Of Subsection 311.2.2. Coarse Aggregate It Shall Conform All The Requirements Of Subsection 311.2.3 Except That Gradation Shall Conform To Table 405.1. Table 405.1 – Grading Requirements For Coarse Aggregate Sieve Designation Mass Percent Passing Standard Mm Alternate Us Standard Class A Class B Class C Class P Class Seal 63 50 37.5 25 19.0 12.5 9.5 4.75 2-1/2” 2” 1-1/2” 1” ¾” ½” 3/8” No.4 100 95 – 100 - 35 – 70 - 10 – 30 0 - 5 100 95 – 100 - 35 – 70 - 10 – 30 - 0 - 5 100 90 – 100 40 – 70 0 – 15* 100 95 – 100 - 20 – 55 0 – 10* 100 95 – 100 - 25 – 60 - 0 – 10* * The Measured Cement Content Shall Be Within Plus (+) Or Minus (-) 2 Mass Percent Of The Design Cement Content. Water It Shall Conform To The Requirements Of Subsection 311.2.4 Reinforcing Steel It Shall Conform To The Requirements Of Item 710, Reinforcing Steel And Wire Rope. Admixtures Admixtures Shall Conform To The Requirements Of Subsection 311.2.7 Curing Materials Curing Materials Shall Conform To The Requirements Of Subsection 311.2.8. Expansion Joint Materials Expansion Joint Materials Shall Be: Preformed Sponge Rubber And Cork, Conforming To Aashto M 153. Hot-poured Elastic Type, Conforming To Aashto M 173. Preformed Fillers, Conforming To Aashto M 213. Elastomeric Compression Joint Seals These Shall Conform To Aashto M 220. Elastomeric Bearing Pads These Shall Conform To Aashto M 251 Or Item 412 – Elastomeric Bearing Pads. Storage Of Cement And Aggregates Storage Of Cement And Aggregates Shall Conform To All The Requirements Of Subsection 311.2.10. Sampling And Testing Of Structural Concrete As Work Progresses, At Least One (1) Sample Consisting Of Three (3) Concrete Cylinder Test Specimens, 150 X 300mm (6 X 12 Inches), Shall Be Taken From Each Seventy-five (75) Cubic Meters Of Each Class Of Concrete Or Fraction Thereof Placed Each Day. Compliance With The Requirements Of This Section Shall Be Determined In Accordance With The Following Standard Methods Of Aashto: Sampling Of Fresh Concrete Weight Per Cubic Metre And Air Content (gravi- Metric) Of Concrete Sieve Analysis Of Fine And Coarse Aggregates Slump Of Portland Cement Concrete Specific Gravity And Absorption Of Fine Aggregate T 141 T 121 T 27 T 119 T 84 Tests For Strength Shall Be Made In Accordance With The Following: Making And Curing Concrete Compressive And Flexural Tests Specimens In The Field Compressive Strength Of Molded Concrete Cylinders T 23 T 22 Production Requirements Proportioning And Strength Of Structural Concrete The Concrete Materials Shall Be Proportioned In Accordance With The Requirements For Each Class Of Concrete As Specified In Table 405.2, Using The Absolute Volume Method As Outlined In The American Concrete Institute (aci) Standard 211.1. “recommended Practice For Selecting Proportions For Normal And Heavyweight Concrete”. Other Methods Of Proportioning May Be Employed In The Mix Design With Prior Approval Of The Engineer. The Mix Shall Either Be Designed Or Approved By The Engineer. A Change In The Source Of Materials During The Progress Of Work May Necessitate A New Mix Design. The Strength Requirements For Each Class Of Concrete Shall Be As Specified In Table 405.2. Table 405.2 - Composition And Strength Of Concrete For Use In Structures Class Of Concrete Minimum Cement Content Per M3 Kg (bag**) Maximum Water/ Cement Ratio Kg/kg Consistency Range In Slump Mm (inch) Designated Size Of Coarse Aggregate Square Opening Std. Mm Minimum Compressive Strength Of 150x300mm Concrete Cylinder Specimen At 28 Days, Mn/m2 (psi) A B C P Seal 360 (9 Bags) 320 (8 Bags) 380 (9.5 Bags) 440 (11 Bags) 380 (9.5 Bags) 0.53 0.58 0.55 0.49 0.58 50 – 100 (2 – 4) 50 – 100 (2 – 4) 50 – 100 (2 – 4) 100 Max. (4 Max.) 100 – 200 (4 - 8) 37.5 – 4.75 (1-1/2” – No. 4) 50 – 4.75 (2” – No. 4) 12.5 – 4.75 (1/2” – No. 4) 19.0 – 4.75 (3/4” – No. 4) 25 – 4.75 (1” – No. 4) 20.7 (3000) 16.5 (2400) 20.7 (3000) 37.7 (5000) 20.7 (3000) * The Measured Cement Content Shall Be Within Plus Or Minus 2 Mass Percent Of The Design Cement Content. ** Based On 40 Kg/bag 405.4.2 Consistency Concrete Shall Have A Consistency Such That It Will Be Workable In The Required Position. It Shall Be Of Such A Consistency That It Will Flow Around Reinforcing Steel But Individual Particles Of The Coarse Aggregate When Isolated Shall Show A Coating Of Mortar Containing Its Proportionate Amount Of Sand. The Consistency Of Concrete Shall Be Gauged By The Ability Of The Equipment To Properly Place It And Not By The Difficulty In Mixing And Transporting. The Quantity Of Mixing Water Shall Be Determined By The Engineer And Shall Not Be Varied Without His Consent. Concrete As Dry As It Is Practical To Place With The Equipment Specified Shall Be Used. 405.4.3 Batching Measuring And Batching Of Materials Shall Be Done At A Batching Plant. Portland Cement Either Sacked Or Bulk Cement May Be Used. No Fraction Of A Sack Of Cement Shall Be Used In A Batch Of Concrete Unless The Cement Is Weighed. All Bulk Cement Shall Be Weighed On An Approved Weighing Device. The Bulk Cement Weighing Hopper Shall Be Properly Sealed And Vented To Preclude Dusting Operation. The Discharge Chute Shall Not Be Suspended From The Weighing Hopper And Shall Be So Arranged That Cement Will Neither Be Lodged In It Nor Leak From It. Accuracy Of Batching Shall Be Within Plus (+) Or Minus (-) 1 Mass Percent. Water Water May Be Measured Either By Volume Or By Weight. The Accuracy Of Measuring The Water Shall Be Within A Range Of Error Of Not More Than 1 Percent. Aggregates Stockpiling Of Aggregates Shall Be In Accordance With Subsection 311.2.10. All Aggregates Whether Produced Or Handled By Hydraulic Methods Or Washed, Shall Be Stockpiled Or Binned For Draining For At Least 12 Hours Prior To Batching. Rail Shipment Requiring More Than12 Hours Will Be Accepted As Adequate Binning Only If The Car Bodies Permit Free Drainage. If The Aggregates Contain High Or Non-uniform Moisture Content, Storage Or Stockpile Period In Excess Of 12 Hours May Be Required By The Engineer. Batching Shall Be Conducted As To Result In A 2 Mass Percent Maximum Tolerance For The Required Materials. Bins And Scales The Batching Plant Shall Include Separate Bins For Bulk Cement, Fine Aggregate And For Each Size Of Coarse Aggregate, A Weighing Hopper, And Scales Capable Of Determining Accurately The Mass Of Each Component Of The Batch. Scales Shall Be Accurate To One-half (0.5) Percent Throughout The Range Used. Batching When Batches Are Hauled To The Mixer, Bulk Cement Shall Be Transported Either In Waterproof Compartments Or Between The Fine And Coarse Aggregate. When Cement Is Placed In Contact With Moist Aggregates, Batches Will Be Rejected Unless Mixed Within 1-1/2 Hours Of Such Contact. Sacked Cement May Be Transported On Top Of The Aggregates. Batches Shall Be Delivered To The Mixer Separate And Intact. Each Batch Shall Be Dumped Cleanly Into The Mixer Without Loss, And, When More Than One Batch Is Carried On The Truck, Without Spilling Of Material From One Batch Compartment Into Another. Admixtures The Contractor Shall Follow An Approved Procedure For Adding The Specified Amount Of Admixture To Each Batch And Will Be Responsible For Its Uniform Operation During The Progress Of The Work. He Shall Provide Separate Scales For The Admixtures Which Are To Be Proportioned By Weight, And Accurate Measures For Those To Be Proportioned By Volume. Admixtures Shall Be Measured Into The Mixer With An Accuracy Of Plus Or Minus Three (3) Percent. The Use Of Calcium Chloride As An Admixture Will Not Be Permitted. 405.4.4 Mixing And Delivery Concrete May Be Mixed At The Site Of Construction, At A Central Point Or By A Combination Of Central Point And Truck Mixing Or By A Combination Of Central Point Mixing And Truck Agitating. Mixing And Delivery Of Concrete Shall Be In Accordance With The Appropriate Requirements Of Aashto M 157 Except As Modified In The Following Paragraphs Of This Section, For Truck Mixing Or A Combination Of Central Point And Truck Mixing Or Truck Agitating. Delivery Of Concrete Shall Be Regulated So That Placing Is At A Continuous Rate Unless Delayed By The Placing Operations. The Intervals Between Delivery Of Batches Shall Not Be So Great As To Allow The Concrete Inplace To Harden Partially, And In No Case Shall Such An Interval Exceed 30 Minutes. In Exceptional Cases And When Volumetric Measurements Are Authorized, For Small Project Requiring Less Than 75 Cu.m. Per Day Of Pouring, The Weight Proportions Shall Be Converted To Equivalent Volumetric Proportions. In Such Cases, Suitable Allowance Shall Be Made For Variations In The Moisture Condition Of The Aggregates, Including The Bulking Effect In The Fine Aggregate. Batching And Mixing Shall Be In Accordance With Astm C 685, Section 6 Through 9. Concrete Mixing, By Chute Is Allowed Provided That A Weighing Scales For Determining The Batch Weight Will Be Used. For Batch Mixing At The Site Of Construction Or At A Central Point, A Batch Mixer Of An Approved Type Shall Be Used. Mixer Having A Rated Capacity Of Less Than A One-bag Batch Shall Not Be Used. The Volume Of Concrete Mixed Per Batch Shall Not Exceed The Mixer’s Nominal Capacity As Shown On The Manufacturer’s Standard Rating Plate On The Mixer Except That An Overload Up To 10 Percent Above The Mixer’s Nominal Capacity May Be Permitted, Provided Concrete Test Data For Strength, Segregation, And Uniform Consistency Are Satisfactory And Provided No Spillage Of Concrete Takes Place. The Batch Shall Be So Charge Into The Drum That A Portion Of The Water Shall Enter In Advance Of The Cement And Aggregates. The Flow Of Water Shall Be Uniform And All Water Shall Be In The Drum By The End Of The First 15 Seconds Of The Mixing Period. Mixing Time Shall Be Measured From The Time All Materials, Except Water, Are In The Drum. Mixing Time Shall Not Be Less Than 60 Seconds For Mixers Having A Capacity Of 1.5m3 Or Less. For Mixers Having A Capacity Greater Than 1.5m3, The Mixing Time Shall Not Be Less Than 90 Seconds. If Timing Starts, The Instant The Skip Reaches Its Maximum Raised Position, 4 Seconds Shall Be Added To The Specified Mixing Time. Mixing Time Ends When The Discharge Chute Opens. The Mixer Shall Be Operated At The Drum Speed As Shown On The Manufacturer’s Name Plate On The Mixer. Any Concrete Mixed Less Than The Specified Time Shall Be Discarded And Disposed Off By The Contractor At His Own Expenses. The Timing Device On Stationary Mixers Shall Be Equipped With A Bell Or Other Suitable Warning Device Adjusted To Give A Clearly Audible Signal Each Time The Lock Is Released. In Case Of Failure Of The Timing Device, The Contractor Will Be Permitted To Continue Operations While It Is Being Repaired, Provided He Furnishes An Approved Timepiece Equipped With Minute And Second Hands. If The Timing Device Is Not Placed In Good Working Order Within 24 Hours, Further Use Of The Mixer Will Be Prohibited Until Repairs Are Made. Retempering Concrete Will Not Be Permitted. Admixtures For Increasing The Workability, For Retarding The Set, Or For Accelerating The Set Or Improving The Pumping Characteristics Of The Concrete Will Be Permitted Only When Specifically Provided For In The Contract, Or Authorized In Writing By The Engineer. Mixing Concrete: General Concrete Shall Be Thoroughly Mixed In A Mixer Of An Approved Size And Type That Will Insure A Uniform Distribution Of The Materials Throughout The Mass. All Concrete Shall Be Mixed In Mechanically Operated Mixers. Mixing Plant And Equipment For Transporting And Placing Concrete Shall Be Arranged With An Ample Auxiliary Installation To Provide A Minimum Supply Of Concrete In Case Of Breakdown Of Machinery Or In Case The Normal Supply Of Concrete Is Disrupted. The Auxiliary Supply Of Concrete Shall Be Sufficient To Complete The Casting Of A Section Up To A Construction Joint That Will Meet The Approval Of The Engineer. Equipment Having Components Made Of Aluminum Or Magnesium Alloys, Which Would Have Contact With Plastic Concrete During Mixing, Transporting Or Pumping Of Portland Cement Concrete, Shall Not Be Used. Concrete Mixers Shall Be Equipped With Adequate Water Storage And A Device Of Accurately Measuring And Automatically Controlling The Amount Of Water Used. Materials Shall Be Measured By Weighing. The Apparatus Provided For Weighing The Aggregates And Cement Shall Be Suitably Designed And Constructed For This Purpose. The Accuracy Of All Weighing Devices Except That For Water Shall Be Such That Successive Quantities Can Be Measured To Within One Percent Of The Desired Amounts. The Water Measuring Device Shall Be Accurate To Plus Or Minus 0.5 Mass Percent. All Measuring Devices Shall Be Subject To The Approval Of The Engineer. Scales And Measuring Devices Shall Be Tested At The Expense Of The Contractor As Frequently As The Engineer May Deem Necessary To Insure Their Accuracy. Weighing Equipment Shall Be Insulated Against Vibration Or Movement Of Other Operating Equipment In The Plant. When The Entire Plant Is Running, The Scale Reading At Cut-off Shall Not Vary From The Weight Designated By The Engineer More Than One Mass Percent For Cement, 1-1/2 Mass Percent For Any Size Of Aggregate, Or One (1) Mass Percent For The Total Aggregate In Any Batch. Mixing Concrete At Site Concrete Mixers May Be Of The Revolving Drum Or The Revolving Blade Type And The Mixing Drum Or Blades Shall Be Operated Uniformly At The Mixing Speed Recommended By The Manufacturer. The Pick-up And Throw-over Blades Of Mixers Shall Be Restored Or Replaced When Any Part Or Section Is Worn 20mm Or More Below The Original Height Of The Manufacturer’s Design. Mixers And Agitators Which Have An Accumulation Of Hard Concrete Or Mortar Shall Not Be Used. When Bulk Cement Is Used And Volume Of The Batch Is 0.5m3 Or More, The Scale And Weigh Hopper For Portland Cement Shall Be Separate And Distinct From The Aggregate Hopper Or Hoppers. The Discharge Mechanism Of The Bulk Cement Weigh Hopper Shall Be Interlocked Against Opening Before The Full Amount Of Cement Is In The Hopper. The Discharging Mechanism Shall Also Be Interlocked Against Opening When The Amount Of Cement In The Hopper Is Underweight By More Than One (1) Mass Percent Or Overweight By More Than 3 Mass Percent Of The Amount Specified. When The Aggregate Contains More Water Than The Quantity Necessary To Produce A Saturated Surface Dry Condition, Representative Samples Shall Be Taken And The Moisture Content Determined For Each Kind Of Aggregate. The Batch Shall Be So Charged Into The Mixer That Some Water Will Enter In Advance Of Cement And Aggregate. All Water Shall Be In The Drum By The End Of The First Quarter Of The Specified Mixing Time. Cement Shall Be Batched And Charged Into The Mixer So That It Will Not Result In Loss Of Cement Due To The Effect Of Wind, Or In Accumulation Of Cement On Surface Of Conveyors Or Hoppers, Or In Other Conditions Which Reduce Or Vary The Required Quantity Of Cement In The Concrete Mixture. The Entire Content Of A Batch Mixer Shall Be Removed From The Drum Before Materials For A Succeeding Batch Are Placed Therein. The Materials Composing A Batch Except Water Shall Be Deposited Simultaneously Into The Mixer. All Concrete Shall Be Mixed For A Period Of Not Less Than 1-1/2 Minutes After All Materials, Including Water, Are In The Mixer. During The Period Of Mixing, The Mixer Shall Operate At The Speed For Which It Has Been Designed. Mixers Shall Be Operated With An Automatic Timing Device That Can Be Locked By The Engineer. The Time Device And Discharge Mechanics Shall Be So Interlocked That During Normal Operation No Part Of The Batch Will Be Charged Until The Specified Mixing Time Has Elapsed. The First Batch Of Concrete Materials Placed In The Mixer Shall Contain A Sufficient Excess Of Cement, Sand, And Water To Coat Inside Of The Drum Without Reducing The Required Mortar Content Of The Mix. When Mixing Is To Cease For A Period Of One Hour Or More, The Mixer Shall Be Thoroughly Cleaned. Mixing Concrete At Central Plant Mixing At Central Plant Shall Conform To The Requirements For Mixing At The Site. Mixing Concrete In Truck Truck Mixers, Unless Otherwise Authorized By The Engineer, Shall Be Of The Revolving Drum Type, Water-tight, And So Constructed That The Concrete Can Be Mixed To Insure A Uniform Distribution Of Materials Throughout The Mass. All Solid Materials For The Concrete Shall Be Accurately Measured And Charged Into The Drum At The Proportioning Plant. Except As Subsequently Provided, The Truck Mixer Shall Be Equipped With A Device By Which The Quantity Of Water Added Can Be Readily Verified. The Mixing Water May Be Added Directly To The Batch, In Which Case A Tank Is Not Required. Truck Mixers May Be Required To Be Provided With A Means Of Which The Mixing Time Can Be Readily Verified By The Engineer. The Maximum Size Of Batch In Truck Mixers Shall Not Exceed The Minimum Rated Capacity Of The Mixer As Stated By The Manufacturer And Stamped In Metal On The Mixer. Truck Mixing, Shall, Unless Other-wise Directed Be Continued For Not Less Than 100 Revolutions After All Ingredients, Including Water, Are In The Drum. The Mixing Speed Shall Not Be Less Than 4 Rpm, Nor More Than 6 Rpm. Mixing Shall Begin Within 30 Minutes After The Cement Has Been Added Either To The Water Or Aggregate, But When Cement Is Charged Into A Mixer Drum Containing Water Or Surface Wet Aggregate And When The Temperature Is Above 32oc, This Limit Shall Be Reduced To 15 Minutes. The Limitation In Time Between The Introduction Of The Cement To The Aggregate And The Beginning Of The Mixing May Be Waived When, In The Judgement Of The Engineer, The Aggregate Is Sufficiently Free From Moisture, So That There Will Be No Harmful Effects On The Cement. When A Truck Mixer Is Used For Transportation, The Mixing Time Specified In Subsection 405.4.4 (3) At A Stationary Mixer May Be Reduced To 30 Seconds And The Mixing Completed In A Truck Mixer. The Mixing Time In The Truck Mixer Shall Be As Specified For Truck Mixing. Transporting Mixed Concrete Mixed Concrete May Only Be Transported To The Delivery Point In Truck Agitators Or Truck Mixers Operating At The Speed Designated By The Manufacturers Of The Equipment As Agitating Speed, Or In Non-agitating Hauling Equipment, Provided The Consistency And Workability Of The Mixed Concrete Upon Discharge At The Delivery Point Is Suitable Point For Adequate Placement And Consolidation In Place. Truck Agitators Shall Be Loaded Not To Exceed The Manufacturer’s Guaranteed Capacity. They Shall Maintain The Mixed Concrete In A Thoroughly Mixed And Uniform Mass During Hauling. No Additional Mixing Water Shall Be Incorporated Into The Concrete During Hauling Or After Arrival At The Delivery Point. The Rate Of Discharge Of Mixed Concrete From Truck Mixers Or Agitators Shall Be Controlled By The Speed Of Rotation Of The Drum In The Discharge Direction With The Discharge Gate Fully Open. When A Truck Mixer Or Agitator Is Used For Transporting Concrete To The Delivery Point, Discharge Shall Be Completed Within One Hour, Or Before 250 Revolutions Of The Drum Or Blades, Whichever Comes First, After The Introduction Of The Cement To The Aggregates. Under Conditions Contributing To Quick Stiffening Of The Concrete Or When The Temperature Of The Concrete Is 30oc, Or Above, A Time Less Than One Hour Will Be Required. Delivery Of Mixed Concrete The Contractor Shall Have Sufficient Plant Capacity And Transportation Apparatus To Insure Continuous Delivery At The Rate Required. The Rate Of Delivery Of Concrete During Concreting Operations Shall Be Such As To Provide For The Proper Handling, Placing And Finishing Of The Concrete. The Rate Shall Be Such That The Interval Between Batches Shall Not Exceed 20 Minutes. The Methods Of Delivering And Handling The Concrete Shall Be Such As Will Facilitate Placing Of The Minimum Handling. Method Of Measurement The Quantity Of Structural Concrete To Be Paid For Will Be The Final Quantity Placed And Accepted In The Completed Structure. No Deduction Will Be Made For The Volume Occupied By Pipe Less Than 100mm (4 Inches) In Diameter Or By Reinforcing Steel, Anchors, Conduits, Weep Holes Or Expansion Joint Materials. Basis Of Payment The Accepted Quantities, Measured As Prescribed In Section 405.5, Shall Be Paid For At The Contract Unit Price For Each Of The Pay Item Listed Below That Is Included In The Bill Of Quantities. Payment Shall Constitute Full Compensation For Furnishing, Placing And Finishing Concrete Including All Labor, Equipment, Tools And Incidentals Necessary To Complete The Work Prescribed In The Item. Payment Will Be Made Under: Pay Item Number Description Unit Of Measurement 405 (1) 405 (2) 405 (3) 405 (4) 405 (5) Structural Concrete, Class A Structural Concrete, Class B Structural Concrete, Class C Structural Concrete, Class P Seal Concrete Cubic Meter Cubic Meter Cubic Meter Cubic Meter Cubic Meter V. Concrete, Masonry And Plastering Works A. General: All Concrete Works To Be Done Herein Shall Be In Accordance With Aci Requirement And/ Or Standard Specifications As Adopted By The Government. B. Cement Shall Be Portland Cement (type1) With 40 Kgs/bag. C. Fine Aggregates Shall Be Clean Hold River Sand, Free From Injurious Amount Of Clay, Loam And Vegetable Matter. D. Coarse Aggregates Shall Be River Run Gravel Or Broken Stones. The Maximum Size Shall Be 1/5 Of The Nearest Dimensions Between Side Forms Of The Concrete Members Or ¾ The Maximum Clear Spacing Between Reinforcing Bars. E. Reinforcing Bars: Reinforcing Bars Shall Be Intermediate Grade And Deformed And Shall Have Minimum Yield Strength Of 275 Mpa (40,000 Psi) F. The Wires Shall Be Locally Produced G.i. Wire Gauge No. 16. G. Placing Reinforcement Provide Bars, Wire Fabrics, Wire Ties, Supports And Other Devices Necessary To Install And Secure Reinforcement. Reinforcement Shall Not Contain Rust, Scale Oil, Grease Clay And Foreign Substances That Would Reduce The Bond. Rusting Of Reinforcement Is A Basis Of Rejection If The Effective Cross-sectional Area Of The Normal Weight Per Foot Of The Reinforcement Has Been Reduced To Less Than Specified In Paragraph Entitled “reinforcing Bars”. Remove Loose Rust Prior To Placing Of Steel. Splices Shall Be Approved Prior To Use. Do Not Splice At Points Of Maximum Stress. Overlapped Welded Wire Fabric The Spacing Of The Cross Wires, Plus 50 Mm (2 Inches). H. Concrete Hollow Blocks: 1. For Walls And Partitions, Use Chb Or Its Equivalent. 2. Minimum Comprehensive Strength Shall Be 700 Psi. I. All Concrete Cured For Least Seven (7) Days To Twenty-eight (28) Days If Possible After Placement To Attain The Required Strength Of Concrete. J. Removal Of Forms: Forms Shall Be Removed In Such A Manner As Not To Impair The Safety And Serviceability Of The Structures. K. Proportions Of All Materials Entering Into Concrete Shall Be Of Class “a”. L. Mixture For Concrete Slab: Thickness Of Slab Shall Be 200mm Thick. A Mixture Of Washed Sand, Screened Gravel And Portland Cement. M. Mixture For Plastering: Thickness Of Plaster Shall Be 16mm Thick. A Mixture Of Washed Sand And Portland Cement. Vi. Wall Installation Use 0.5mm Thk G.i. Rib-type Longspan Prepainted For Wall Cladding And 2” X 4” X 1.5mm X 6m C-purlins For Wall Cladding Framing. Section Vii. Drawings Annex A – Architectural Design Annex B- Project Billboard Plan Section Viii. Bill Of Quantities Bid No. Agr- 24-219-b Item Description Quantity Unit Unit Cost Total Cost No. I. Clearing, Grubbing, And Staking 733.50 Sq.m. Pesos And Ctvs. (p ) / Sq.m. P Ii. Excavation Works 391.77 Cu.m. Pesos And Ctvs. (p ) / Cu.m. P Iii. Backfill 275.16 Cu.m. Pesos And Ctvs. (p ) / Cu.m P Iv-a. Concreting (concrete Works) 185.02 Cu.m. Pesos And Ctvs. (p ) /cu.m. P Iv-b. Gravel Bedding (concrete Works) 16.28 Cu.m Pesos And Ctvs. (p ) /cu.m P Item Description Quantity Unit Unit Cost Total Cost No. Iv-c. Steel Works (concrete Works) 11,500.00 Kgs. Pesos And Ctvs. (p ) / Kgs. P Iv-d Formworks (concrete Works) 1,356.36 Sq.m. Pesos And Ctvs. (p ) / Sq.m. P V. Masonry Works 1,271.40 Sq.m. Pesos And Ctvs. (p ) / Sq.m P Vi. Plastering Works 2,886.00 Sq..m Pesos And Ctvs. (p ) / Cu.m P Total Bid Cost In Figures P Total Bid Cost In Words Summary Of Costs Item No. Bid Amount Clearing, Grubbing, And Staking ₱ _____________________________ Excavation Works ₱ _____________________________ Backfill ₱ _____________________________ Iv-a. Concreting (concrete Works) ₱ _____________________________ Iv-b. Gravel Bedding (concrete Works) ₱ _____________________________ Iv-c. Steel Works (concrete Works) ₱ _____________________________ Iv-d. Formworks (concrete Works) ₱ _____________________________ V. Masonry Works ₱ _____________________________ Vi. Plastering Works ₱ _____________________________ Total Bid Amount ₱ _____________________________ Section Ix. Checklist Of Technical And Financial Documents Technical Component Envelope Class “a” Documents Legal Documents ⬜ Valid Philgeps Registration Certificate (platinum Membership) (all Pages) In Accordance With Section 8.5.2 Of The Irr; 1. Registration Certificate From Sec, Department Of Trade And Industry (dti) For Sole Proprietorship Or Cda For Cooperatives, Or Any Proof Of Such Registration. 2. Mayor’s Permit Issued By The City Or Municipality – Where The Principal Place Of Business Of The Prospective Bidder Is Located; 3. Tax Clearance Per Executive Order 398, Series Of 2005,a S Finally Reviewed And Approved By The Bir 4. Audited Financial Statements, Showing, Among Others, The Prospective Total And Current Assets And Liabilities, Stamped “received” By The Bir Or Its Duly Accredited And Authorized Institutions For The Preceding Calendar Year Which Should Not Be Earlier Than Two(2) Years From The Date Of Bid Submission; For The Type And Cost Of The Contract To Be Bid Technical Documents ⬜ Statement Of The Prospective Bidder Of All Its Ongoing Government And Private Contracts, Including Contracts Awarded But Not Yet Started, If Any, Whether Similar Or Not Similar In Nature And Complexity To The Contract To Be Bid; And ⬜ Statement Of The Bidder’s Single Largest Completed Contract (slcc) Similar To The Contract To Be Bid, Except Under Conditions Provided Under The Rules; And ⬜ Special Pcab License In Case Of Joint Ventures; And Registration For The Type And Cost Of The Contract To Be Bid; And ⬜ Original Copy Of Bid Security. If In The Form Of A Surety Bond, Submit Also A Certification Issued By The Insurance Commission; Or Original Copy Of Notarized Bid Securing Declaration; And Project Requirements, Which Shall Include The Following: ⬜ Organizational Chart For The Contract To Be Bid; ⬜ List Of Contractor’s Key Personnel (e.g., Project Manager, Project Engineers, Materials Engineers, And Foremen), To Be Assigned To The Contract To Be Bid, With Their Complete Qualification And Experience Data; ⬜ List Of Contractor’s Major Equipment Units, Which Are Owned, Leased, And/or Under Purchase Agreements, Supported By Proof Of Ownership Or Certification Of Availability Of Equipment From The Equipment Lessor/vendor For The Duration Of The Project, As The Case May Be; And ⬜ Original Duly Signed Omnibus Sworn Statement (oss); And If Applicable, Original Notarized Secretary’s Certificate In Case Of A Corporation, Partnership, Or Cooperative; Or Original Special Power Of Attorney Of All Members Of The Joint Venture Giving Full Power And Authority To Its Officer To Sign The Oss And Do Acts To Represent The Bidder. Financial Documents ⬜ The Prospective Bidder’s Computation Of Net Financial Contracting Capacity (nfcc). Class “b” Documents ⬜ If Applicable, Duly Signed Joint Venture Agreement (jva) In Accordance With Ra No. 4566 And Its Irr In Case The Joint Venture Is Already In Existence; Or Duly Notarized Statements From All The Potential Joint Venture Partners Stating That They Will Enter Into And Abide By The Provisions Of The Jva In The Instance That The Bid Is Successful. Financial Component Envelope ⬜ Original Of Duly Signed And Accomplished Financial Bid Form; And Other Documentary Requirements Under Ra No. 9184 ⬜ Original Of Duly Signed Bid Prices In The Bill Of Quantities; And ⬜ Duly Accomplished Detailed Estimates Form, Including A Summary Sheet Indicating The Unit Prices Of Construction Materials, Labor Rates, And Equipment Rentals Used In Coming Up With The Bid; And ⬜ Cash Flow By Quarter. Bid Form For The Procurement Of Infrastructure Projects [shall Be Submitted With The Bid] Bid Form Date : Project Identification No. : To: [name And Address Of Procuring Entity] Having Examined The Philippine Bidding Documents (pbds) Including The Supplemental Or Bid Bulletin Numbers [insert Numbers], The Receipt Of Which Is Hereby Duly Acknowledged, We, The Undersigned, Declare That: We Have No Reservation To The Pbds, Including The Supplemental Or Bid Bulletins, For The Procurement Project: [insert Name Of Contract]; We Offer To Execute The Works For This Contract In Accordance With The Pbds; The Total Price Of Our Bid In Words And Figures, Excluding Any Discounts Offered Below Is: [insert Information]; The Discounts Offered And The Methodology For Their Application Are: [insert Information]; The Total Bid Price Includes The Cost Of All Taxes, Such As, But Not Limited To: [specify The Applicable Taxes, E.g. (i) Value Added Tax (vat), (ii) Income Tax, (iii) Local Taxes, And (iv) Other Fiscal Levies And Duties], Which Are Itemized Herein And Reflected In The Detailed Estimates, Our Bid Shall Be Valid Within The Period Stated In The Pbds, And It Shall Remain Binding Upon Us At Any Time Before The Expiration Of That Period; If Our Bid Is Accepted, We Commit To Obtain A Performance Security In The Amount Of [insert Percentage Amount] Percent Of The Contract Price For The Due Performance Of The Contract, Or A Performance Securing Declaration In Lieu Of The The Allowable Forms Of Performance Security, Subject To The Terms And Conditions Of Issued Gppb Guidelines12 For This Purpose; We Are Not Participating, As Bidders, In More Than One Bid In This Bidding Process, Other Than Alternative Offers In Accordance With The Bidding Documents; We Understand That This Bid, Together With Your Written Acceptance Thereof Included In Your Notification Of Award, Shall Constitute A Binding Contract Between Us, Until A Formal Contract Is Prepared And Executed; And We Understand That You Are Not Bound To Accept The Lowest Calculated Bid Or Any Other Bid That You May Receive. We Likewise Certify/confirm That The Undersigned, Is The Duly Authorized Representative Of The Bidder, And Granted Full Power And Authority To Do, Execute 12 Currently Based On Gppb Resolution No. 09-2020 And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For The [name Of Project] Of The [name Of The Procuring Entity]. We Acknowledge That Failure To Sign Each And Every Page Of This Bid Form, Including The Bill Of Quantities, Shall Be A Ground For The Rejection Of Our Bid. Name: Legal Capacity: Signature: Duly Authorized To Sign The Bid For And Behalf Of: Date: Bid Securing Declaration Form [shall Be Submitted With The Bid If Bidder Opts To Provide This Form Of Bid Security] Republic Of The Philippines) City Of ) S.s. Bid Securing Declaration Project Identification No.: [insert Number] To: [insert Name And Address Of The Procuring Entity] I/we, The Undersigned, Declare That: I/we Understand That, According To Your Conditions, Bids Must Be Supported By A Bid Security, Which May Be In The Form Of A Bid Securing Declaration. I/we Accept That: (a) I/we Will Be Automatically Disqualified From Bidding For Any Procurement Contract With Any Procuring Entity For A Period Of Two (2) Years Upon Receipt Of Your Blacklisting Order; And, (b) I/we Will Pay The Applicable Fine Provided Under Section 6 Of The Guidelines On The Use Of Bid Securing Declaration, Within Fifteen (15) Days From Receipt Of The Written Demand By The Procuring Entity For The Commission Of Acts Resulting To The Enforcement Of The Bid Securing Declaration Under Sections 23.1(b), 34.2, 40.1 And 69.1, Except 69.1(f),of The Irr Of Ra No. 9184; Without Prejudice To Other Legal Action The Government May Undertake. I/we Understand That This Bid Securing Declaration Shall Cease To Be Valid On The Following Circumstances: Upon Expiration Of The Bid Validity Period, Or Any Extension Thereof Pursuant To Your Request; I Am/we Are Declared Ineligible Or Post-disqualified Upon Receipt Of Your Notice To Such Effect, And (i) I/we Failed To Timely File A Request For Reconsideration Or (ii) I/we Filed A Waiver To Avail Of Said Right; And I Am/we Are Declared The Bidder With The Lowest Calculated Responsive Bid, And I/we Have Furnished The Performance Security And Signed The Contract. In Witness Whereof, I/we Have Hereunto Set My/our Hand/s This Day Of [month] [year] At [place Of Execution]. [insert Name Of Bidder Or Its Authorized Representative] [insert Signatory’s Legal Capacity] Affiant [jurat] [format Shall Be Based On The Latest Rules On Notarial Practice] Omnibus Sworn Statement (revised) [shall Be Submitted With The Bid] Republic Of The Philippines ) City/municipality Of ) S.s. Affidavit I, [name Of Affiant], Of Legal Age, [civil Status], [nationality], And Residing At [address Of Affiant], After Having Been Duly Sworn In Accordance With Law, Do Hereby Depose And State That: [select One, Delete The Other:] [if A Sole Proprietorship:] I Am The Sole Proprietor Or Authorized Representative Of [name Of Bidder] With Office Address At [address Of Bidder]; [if A Partnership, Corporation, Cooperative, Or Joint Venture:] I Am The Duly Authorized And Designated Representative Of [name Of Bidder] With Office Address At [address Of Bidder]; [select One, Delete The Other:] [if A Sole Proprietorship:] As The Owner And Sole Proprietor, Or Authorized Representative Of [name Of Bidder], I Have Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For [name Of The Project] Of The [name Of The Procuring Entity], As Shown In The Attached Duly Notarized Special Power Of Attorney; [if A Partnership, Corporation, Cooperative, Or Joint Venture:] I Am Granted Full Power And Authority To Do, Execute And Perform Any And All Acts Necessary To Participate, Submit The Bid, And To Sign And Execute The Ensuing Contract For [name Of The Project] Of The [name Of The Procuring Entity], As Shown In The Attached [state Title Of Attached Document Showing Proof Of Authorization (e.g., Duly Notarized Secretary’s Certificate, Board/partnership Resolution, Or Special Power Of Attorney, Whichever Is Applicable;)]; [name Of Bidder] Is Not “blacklisted” Or Barred From Bidding By The Government Of The Philippines Or Any Of Its Agencies, Offices, Corporations, Or Local Government Units, Foreign Government/foreign Or International Financing Institution Whose Blacklisting Rules Have Been Recognized By The Government Procurement Policy Board, By Itself Or By Relation, Membership, Association, Affiliation, Or Controlling Interest With Another Blacklisted Person Or Entity As Defined And Provided For In The Uniform Guidelines On Blacklisting; Each Of The Documents Submitted In Satisfaction Of The Bidding Requirements Is An Authentic Copy Of The Original, Complete, And All Statements And Information Provided Therein Are True And Correct; [name Of Bidder] Is Authorizing The Head Of The Procuring Entity Or Its Duly Authorized Representative(s) To Verify All The Documents Submitted; [select One, Delete The Rest:] [if A Sole Proprietorship:] The Owner Or Sole Proprietor Is Not Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; [if A Partnership Or Cooperative:] None Of The Officers And Members Of [name Of Bidder] Is Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; [if A Corporation Or Joint Venture:] None Of The Officers, Directors, And Controlling Stockholders Of [name Of Bidder] Is Related To The Head Of The Procuring Entity, Members Of The Bids And Awards Committee (bac), The Technical Working Group, And The Bac Secretariat, The Head Of The Project Management Office Or The End-user Unit, And The Project Consultants By Consanguinity Or Affinity Up To The Third Civil Degree; [name Of Bidder] Complies With Existing Labor Laws And Standards; And [name Of Bidder] Is Aware Of And Has Undertaken The Responsibilities As A Bidder In Compliance With The Philippine Bidding Documents, Which Includes: Carefully Examining All Of The Bidding Documents; Acknowledging All Conditions, Local Or Otherwise, Affecting The Implementation Of The Contract; Making An Estimate Of The Facilities Available And Needed For The Contract To Be Bid, If Any; And Inquiring Or Securing Supplemental/bid Bulletin(s) Issued For The [name Of The Project]. [name Of Bidder] Did Not Give Or Pay Directly Or Indirectly, Any Commission, Amount, Fee, Or Any Form Of Consideration, Pecuniary Or Otherwise, To Any Person Or Official, Personnel Or Representative Of The Government In Relation To Any Procurement Project Or Activity. In Case Advance Payment Was Made Or Given, Failure To Perform Or Deliver Any Of The Obligations And Undertakings In The Contract Shall Be Sufficient Grounds To Constitute Criminal Liability For Swindling (estafa) Or The Commission Of Fraud With Unfaithfulness Or Abuse Of Confidence Through Misappropriating Or Converting Any Payment Received By A Person Or Entity Under An Obligation Involving The Duty To Deliver Certain Goods Or Services, To The Prejudice Of The Public And The Government Of The Philippines Pursuant To Article 315 Of Act No. 3815 S. 1930, As Amended, Or The Revised Penal Code. In Witness Whereof, I Have Hereunto Set My Hand This Day Of , 20 At , Philippines. [insert Name Of Bidder Or Its Authorized Representative] [insert Signatory’s Legal Capacity] Affiant [jurat] [format Shall Be Based On The Latest Rules On Notarial Practice]