Fabrication Tenders

Details: Description Project Billboard/signboard, Perimeter Fence: Structure Excavation (common Soil), Structural Concrete (28 Mpa @ 28 Days), Reinforcing Steel (deformed) Grade 40, Formworks And Falseworks, Chb Non-load Bearing Including Reinforcing Steel (100mm), Cement Plaster Finish, Metal Structure Accessories (steel Fence And Steel Gate), Roof Frame And Roofing Works: Formworks And Falseworks, Structural Steel (trusses), Structural Steel (purlins), Fabricating Metal Roofing Accessory (flashing, 0.50mm Thk.), Prepainted Metal Sheet (rib Type, Long Span, 0.50mm Thk.), Painting Works: Painting Works (steel), Solar Panel Works: Panel Board With Main & Branches Breakers And Wires, Solar Panel With Inverter, Batteries, And Other Devices 1. The Municipality Of Culasi, Through The 20% Development Fund Of Nta, Intends To Apply The Sum Of P1,000,000.00 Being The Approved Budget For The Contract (abc) To Payments Under The Contract For Infra-2025-002. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. 2. The Municipality Of Culasi Now Invites Bids For The Above Procurement Project. Completion Of The Works Is Required In 60 Calendar Days. Bidders Should Have Completed A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii (instructions To Bidders). 3. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using Non-discretionary “pass/fail” Criteria As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) No. 9184. 4. Interested Bidders May Obtain Further Information From The Municipality Of Culasi And Inspect The Bidding Documents At The Address Given Below From 8:00 Am – 5:00 Pm. 5. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders From February 21, 2025- February 28, 2025, From The Given Address And Website/s Below And Upon Payment Of The Applicable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb, In The Amount Of One Thousand Pesos Only (p 1,000.00). The Procuring Entity Shall Allow The Bidder To Present Its Proof Of Payment For The Fees Presented In Person. Municipal Treasurer’s Office Municipal Building Culasi, Antique 6. Bids Must Be Duly Received By The Bac Secretariat Through Manual Submission At The Office Address Indicated Below On February 28, 2025. Late Bids Shall Not Be Accepted. 7. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 16. 8. Bid Opening Shall Be At 9:01 A.m. On February 28, 2025, At The Municipal Bac Office, Municipal Hall, Culasi, Antique. Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend The Activity. 9. The Municipality Of Culasi Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Implementing Rules And Regulations (irr) Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 10. For Further Information, Please Refer To: April Rose G. Rendon Bac Sec Member Municipal Hall, Municipality Of Culasi, Province Of Antique 277-8748

Details: The Purpose Of This Sources Sought Notice Is To Conduct Market Research And Identify Potential Sources Of Commercial Products/services That Satisfy The Government’s Anticipated Needs. background the National Institute Of Standards And Technology (nist), Physical Measurement Laboratory (pml), Microsystems And Nanotechnology Division (mnd), Chips R&d Program (https://www.nist.gov/chips/metrology-community) As Part Of The Chips Act Activities, Is Now Developing Imaging And Measurement Solutions For Integrated Circuit (ic) Overlay Metrology Using A Scanning Electron Microscope (sem). Ic Production Relies On Measurements Of The 3d Size, Shape, And Placement Of Structures With Atomic-level Precision And Repeatability. The Project Will Create A Sound Scientific Foundation And Comprehensive Solutions For Sem-based Overlay And Dimensional Metrology Superior To Currently Used Arbitrary Methods. This Will Allow The Design Of Overlay Patterns, Acquisition, And Image Analysis To Be Optimized Entirely Through Artificial Intelligence, Physics-based Simulation, And Modeling And Meet Ic Production Requirements Now And In The Future. nist Mnd Requires A Wafer Relevant To Current Ic Technologies Suitable For The Sem Overlay Measurements Of Cu Lines That Can Be Covered With Various Si Oxide Layers. Although This Sample Only Approximates The Complete Overlay Structure, It Can Be Used To Assess The Advantage Of Using The Physics Of Signal Generation Over Simplistic Methods That Are Not Based On A Physics Model. The Wafer Containing Many Full-size Chips Will Be Diced Into Individual Chips That Will Be Covered By Various Thickness Si Oxide Layers At Nist Nanofab. The Process Will Create A Set Of See-through Overlay Metrology Samples Needed For The Sem Overlay Metrology Project. nist Is Seeking Information From Sources That May Be Capable Of Providing A Commercial Solution That Will Achieve The Objectives Described Above, In Addition To The Following Essential Requirements: for The Sem Overlay Metrology Project, Nist Requires A 300 Mm Si Wafer Sample Of A Set Of Chips With Cu Damascene Patterns Suitable For Research And Development Efforts To Evaluate The Feasibility Of Physics-based Simulations And Ai-based Modeling As The Means To Improve The Performance Of Sem-based Overlay Metrology. 193 Nm Lithography Shall Be Used To Create The Overlay Metrology Patterns. It Is Also Advantageous, But Not Required To Place Other Than Overlay Dimensional Metrology Patterns On The Chips. All Chips Across The Wafer Shall Be Made Identical, Naturally Occurring Small Variations Due To Fabrication Processes Are Permitted. specifically, The Contractor Shall Provide One Wafer Containing At Least 12 Chips With The Following Overlay Metrology Parameters: 1. Cu Damascene Patterns With Box-in-box (bib), Image-based Overlay (ibo), Advanced Imaging Metrology (aim) Grating Patterns, And Hitachi-type Sem-based Overlay (sbo). Pattern Design Can Be Found In Pertinent Public Literature; See, For Example, [1] Or Elsewhere. 2. Sets Of Varying Size Bib, Ibo, Aim And Sbo Overlay Metrology Patterns Must Be Included In The Less Than 150 Mm To Smaller Than 50 Mm Range. 3. Overlay Patterns With Intentional, Small, Close To 1, 2, 5, And 10 Nm Variations Of Known Overlay Offsets (shifts) Must Be Provided. 4. The Wafer Must Be Covered With A Protective Layer To Safeguard The Integrity Of The Cu Patterns. 5. A Gdsii-based Map With Pattern Locations And Properties (size, Type, Offset, Etc.) Identification Must Be Provided. 6. Documentation About The Wafer Material, Dopant Type And Concentration, And The Patterning Process Shall Be Provided. how To Respond To This Notice in Responding To This Notice, Please Do Not Provide Proprietary Information. Please Include Only The Following Information, Readable In Either Microsoft Word 365, Microsoft Excel 365, Or .pdf Format, In The Response: Submit The Response By Email To The Primary Point Of Contact And, If Specified, To The Secondary Point Of Contact Listed In This Notice As Soon As Possible, And Preferably Before The Closing Date And Time Of This Notice. Please Note That To Be Considered For Award Under Any Official Solicitation, The Entity Must Be Registered And “active” In Sam At The Time Of Solicitation Response. provide The Complete Name Of Your Company, Address, Name Of Contact For Follow-up Questions, Their Email, Their Phone Number And, If Your Company Has An Active Registration In Https://sam.gov, Your Company’s Unique Entity Id (uei). identify The Equipment That Your Company Sells That Can Meet The Objectives Addressed In The Background Section Of This Notice. For Each Product Recommended To Meet The Government’s Requirement, Provide The Following: manufacturer Name model Number technical Specifications if Your Company Is Not The Manufacturer, Provide Information On Your Company’s Status As An Authorized Reseller Of The Product(s) describe Performance Capabilities Of The Product(s) Your Company Recommends To Meet The Government’s Requirements. Additionally, If There Are Other Features Or Functions That You Believe Would Assist Nist In Meeting Its Objectives Described Above, Please Discuss In Your Response. discuss Whether The Equipment That Your Company Sells And Which You Describe In Your Response To This Notice May Be Customized To Specifications And Indicate Any Limits To Customization. identify Any Aspects Of The Nist Market Research Notice, Including Instructions, And Draft Minimum Specifications In The Background Section You Cannot Meet And State Why. Please Offer Suggestions For How The Market Research Notice And Draft Minimum Specifications Could Be Made More Competitive. state Whether The Proposed Equipment Is Manufactured In The United States And, If Not, State The Name Of The Country Where The Equipment Is Manufactured. identify Any Plans/possibilities For Changes In Manufacturing Location Of The Aforementioned Equipment And Provide Relevant Details, Including Timeline. for The Naics Code Listed In This Notice: indicate Whether Your Company Is (a) A Small Business Or (b) Other Than Small Business. See The Table Of Small Business Size Standards And The Associated .pdf Download File For Small Business Size Standards And Additional Information. if You Believe The Naics Code Listed In This Notice Is Not The Best Naics Code For The Type Of Product Addressed In This Notice, Identify An Alternative Naics Code That You Believe Would Be More Appropriate For The Planned Procurement. describe Services That Are Available With The Purchase Of The Aforementioned Equipment From Your Company Such As Installation, Training, And Equipment Maintenance. describe Standard Terms And Conditions Of Sale Offered By Your Company For The Recommended Equipment Such As: Delivery Time After Your Company Accepts The Order; Fob Shipping Terms; Manufacturer Warranty (including Details Regarding Nature And Duration); If Available, Description(s) Of Available Extended Warranty; Equipment Setup And Test; Operator And Service Instruction Manual(s); Cleanup After Installation; And If Applicable, Other Offered Services. Provide A Copy Of Manufacturer Standard Terms And Conditions That Typically Relate To The Sale Of The Specified Equipment, If Available. state Whether Your Company Offers Facility Renovation Services Related To Installation Of The Recommended Equipment At Its Delivery Destination, If Required Per The Nist-identified Minimum Specifications, And Provide Description Of Said Services. Indicate If Your Company Performs The Facility Renovation Services Or Typically Subcontracts The Work To Another Company. Indicate If Your Company Would Be Interested In Inspecting The Intended Installation Site During The Market Research Phase. state Published Price, Discount, Or Rebate Arrangements For Recommended Equipment And/or Provide Link To Access Company’s Published Prices For Equipment And Services. if The Recommended Equipment And Related Services Are Available For Purchase On Any Existing Federal Supply Schedule Contract(s) Or Other Contracts Against Which Nist May Be Able To Place Orders, Identify The Contract Number(s) And Other Relevant Information. identify Any Customers In The Public Or Private Sectors To Which You Provided The Recommended Or Similar Equipment. Include Customer(s) Information: Company Name, Phone Number, Point Of Contact, Email Address. provide Any Other Information That You Believe Would Be Valuable For Nist To Know As Part Of Its Market Research For This Requirement. state If You Require Nist To Provide Additional Information To Improve Your Understanding Of The Government’s Requirement And/or Would Like To Meet With Nist Representatives To Discuss The Requirement And The Capabilities Of The Identified Equipment. questions Regarding This Notice questions Regarding This Notice May Be Submitted Via Email To The Primary Point Of Contact And The Secondary Point Of Contact Listed In This Notice. Questions Should Be Submitted So That They Are Received 5 Days Prior To The Response Date. If The Contracting Officer Determines That Providing A Written Amendment To This Notice To Document Question(s) Received Would Benefit Other Potential Respondents, The Questions Would Be Anonymized, And A Written Response To Such Question(s) Would Be Provided Via An Amendment To This Notice. important Notes this Notice Is For Market Research Purposes And Should Not Be Construed As A Commitment By Nist To Issue A Solicitation Or Ultimately Award A Contract. There Is No Solicitation Available At This Time. this Notice Does Not Obligate The Government To Award A Contract Or Otherwise Pay For The Information Provided In Response. nist Reserves The Right To Use Information Provided By Respondents For Any Purpose Deemed Necessary And Legally Appropriate. any Organization Responding To This Notice Should Ensure That Its Response Is Complete And Sufficiently Detailed To Allow The Government To Determine The Organization’s Capability. respondents Are Advised That The Government Is Under No Obligation To Acknowledge Receipt Of The Information Received Or Provide Feedback To Respondents With Respect To Any Information Submitted. after A Review Of The Responses Received, A Synopsis And Solicitation May Be Published On Gsa’s Ebuy Or Sam.gov. However, Responses To This Notice Will Not Be Considered An Adequate Response To Any Such Solicitation(s). thank You For Taking The Time To Submit A Response To This Request!

Details: Description Republic Of The Philippines Province Of Zamboanga Sibugay Municipality Of Roseller T. Lim Invitation To Bid February 10, 2025 To All Interested Bidders: Notice Is Hereby Served That Sealed Bid Be Received For Public Bidding Under The Harmonious Procurement Process In The Office Of The Bids And Awards Committee On February 24, 2025 At Exactly 1:30 Pm For The Following Articles Stated Below; Items & Description Quantity Unit Motorpool Acetylene 2.00 Tanks Wd40 2.00 Can 5kls Welding Rod 1.00 Box 2.5kls Welding Rod 3.00 Box Cutting Disc 8.00 Pcs Grinding Stone 2.00 Pcs Welding Holder 1.00 Box Hose Clam 1.00 Pc Hose Connector 2.00 Set Welding Glass 2.00 Pcs Rubber Cup 2.00 Pcs Led 18w 1.00 Pc Auto Bulb 24v 4.00 Pcs Paint Black W/ Thinner 1.00 Ltr Wire #18 40.00 Mtrs Wire #10 10.00 Mtrs Elec. Tape 3.00 Pcs Breaker 3.00 Pcs Door Knob 3.00 Pcs Led Bulb 7.00 Pcs Epoxy Primer 3.00 Ltr Bulb 15w 2.00 Pcs Loader V-belt #44b 2.00 Pcs Waterpump 1.00 Pc Wire #14 4.00 Mtrs Fuse Single 1.00 Pc Elec. Tape 2.00 Pcs Relay 24x 1.00 Pc Autowire #16 1.00 Roll Stranded Wire #18 22.00 Mtrs Paint Brush #2 2.00 Pcs Coolparts 1.00 Pc Vulcaseal 1.00 Can Rubber Cup 60x45x9 2.00 Pcs Dt Yellow Fuel Hose 100ft 3.00 Mtrs Clip 4.00 Pcs Vulcaseal 1.00 Can Padlock 1.00 Pc Gasket All 1.00 Pc Rivets 6.00 Pcs Center Bolt 1/2 1.00 Pc Expansion Bolt 5/8 6.00 Pcs Grader Bronze Rod 2.00 Pcs Wd40 2.00 Can Nut 1.00 Pc Oring 1.00 Pc Welding Rod 1.00 Box Lock Washed 3.00 Pcs Back Horn 2.00 Pcs Padlock 2.00 Pcs Balik-balik-menro Bulb Double Contact 4.00 Pcs Electrical Tape 1.00 Pc Clearance Light 1.00 Set Piston Ring New 1.00 Set Tras. Support F6 2.00 Pcs Car Cleaner 1.00 Pc Canter White Tire 750x16 2.00 Pcs Padlock 1.00 Pc Wheel Bolt 1.00 Pcs Devcon 1.00 Set Bolt W/nut Lock Washer 4.00 Pcs Cutting Disc 5.00 Pcs Bolt 10mx1 W/lock Wacher 4.00 Pcs Belt A-45 2.00 Pcs Carbon Brush 1.00 Set Garbage Truck Spray Paint Black 1.00 Pc Tapelon 1.00 Pc Tire 8.25x20 3.00 Pcs Bolt 8mm 8.00 Pcs Spray Paint Gray 1.00 Can Grinding Stone 2.00 Pcs Cutting Disc 3.00 Pcs Welding Rod 1.00 Box Battery Clamp 4.00 Pcs Repair Kit 1.00 Pc Clutch Booster 1.00 Pc Lowbed 11rx22.5 Tire 3.00 Pcs Black Acrylic Noncoat 2.00 Ltrs Paint Brush #2 1.00 Pc Thinner 1.00 Gal Injection Pump Calibration 1.00 Pc Canter Blue Sand Paper #120 4.00 Pcs Stopper 1.00 Pc Lock 1.00 Pc Shatter Bracket 1.00 Pc Dumptruck Aircleaner 1.00 Pc Wheel Bolt 3.00 Pcs Battery Clamp 4.00 Pcs Fitting Hose 1.00 Set Accelarator 1.00 Set Side Car-mswd Brake Shoe 1.00 Pc Bearing 6302 2.00 Pcs Prado Rubber Cup Secondary Clutch 1.00 Pc Sand Paper #1000 1.00 Pc Electrical Tape 1.00 Pc Hilux Orange Tire 265/70 R17 2.00 Pcs Bearing Dg15 1.00 Pc L300 195x14 White Tube 1.00 Pc Legislative Van Upper Arm Assembly 1.00 Set Fuel Filter 1.00 Set Oil Filter 1.00 Pc Taggle Switch 2.00 Pcs Brake Pad 1.00 Set Bachoe Fuel Filter 2.00 Pcs Air Cleaner 1.00 Pc Black Horn 1.00 Set Wd40 3.00 Pcs Pylox 1.00 Can Oil Filter #c-223 1.00 Pc Battery 21 Plates 2.00 Pcs Fabrication Of Engenering Plastic 2.00 Pcs Mixer Bolts 8mmx1/2 W/nut 4.00 Pcs Welding Rod 2.5kls 1.00 Box V-belt B-64 2.00 Pcs Welding Rod Stainless 3.00 Pcs Ambulance Rubber Cup 4.00 Pcs Cable Tie 5.00 Pcs Head Light Bulb 12v 2.00 Pcs Brake Pad 2.00 Set Brake Shoe 1.00 Set Wd40 2.00 Can 8mmx1 W/nut Flat Wacher 8.00 Pcs Battery 9 Plate 2.00 Pcs Assemble 1.00 Pc Cutting Disc 5.00 Pcs Oil Filter 1.00 Pc Fuel Pump Assembly 2.00 Pcs Bolt 8mm X 1 W/nut 2.00 Pcs Sealant 1.00 Pc Kanyoto 1.00 Pc Bonggo Rubber Cup Clutch 2.00 Pcs Rubber Brake Master 2.00 Pcs Rubber Cup 2.00 Pcs Hammer -ld Cutting Disc 3.00 Pcs Pylox 2.00 Can Tapelon 1.00 Pc Wd40 1.00 Can Gum 1.00 Pc Mud Guard 1.00 Mtr Bolt 6mmx1 1/2 Set 12.00 Pcs Battery Clip 2.00 Pcs Strada -ld Oil Filter 1.00 Pc Wiper Wash 2.00 Ltrs Welding Rod 1.00 Box Door Lock 2.00 Pcs Horn 2.00 Pcs Cutting Disc 10.00 Pcs Cutting Blade 5.00 Pcs Oil Filter 1.00 Pc Flushing Oil 1.00 Ltr Hose Connector W/ Clip 1.00 Set Wiper Wash 2.00 Ltrs Refitting Car Hose 1.00 Pc Rubber Cup 2.00 Pcs Tire Sealant 2.00 Pcs Car Wash Hose 10.00 Mtrs Sealant 1.00 Pc Patch 1.00 Pc Police Car Wiper Blade 1.00 Pc Oil Filter 2.00 Pcs Tire 235/70 R15 4.00 Pcs Sealant 1.00 Pc Cutting Disc 3.00 Pcs Welding Rod 2.5kls 2.00 Box Welding Rod 5kls 1.00 Box Cutting Disc 10.00 Pcs Oxygen 1.00 Tank Red Oxide 1.00 Ltr Paint Brush #2 1.00 Pc Vulcaseal 1.00 Can Bulb Single Contact 4.00 Pcs Double Contact 4.00 Pcs Electrical Tape 1.00 Pc Bolt 8mmx1/2 Nut Wacher 16.00 Pcs Brake Pad 1.00 Set Tire Sealant 2.00 Pcs Purpose: Sparepart For Governmenet – Owned Vehicles . R. T. Lim, Zamboanga Sibugay The Tender Document Forms Are Available In The Office Of The Bac/bac Secretariat Effective On Feb. 11, 2025 Office Hours. The Total Estimated Amount Of The Above Stated Supplies Equivalent To Three Hundred Sixty Five Thousand Four Hundred Eighty Seven Pesos & 25/100 Only (php365,487.25). Please Be Reminded That The Bac Have The Right To Rejected Any Or All Bids And Accept Only Those Bids Most Advantageous To The Lgu. Engr. Albert Dela Peña Bac Chairman

Details: Description Republic Of The Philippines Province Of Aurora Municipality Of Dipaculao Invitation To Bid A. The Local Government Unit (lgu) Of Dipaculao, Aurora, Through Its Bids And Awards Committee (bac) Invites Contractors To Apply To Bid For The Following Contracts: 1. A) Contract Id.: 2025-02-03 B) Contract Name: Improvement Of Covered Court C) Contract Location: Barangay Sapangkawayan, Dipaculao, Aurora D) Approved Budget For The Contract (abc): Php 1,000,000.00 E) Scope Of Works: Masonry Works, Embankment From Borrow, Structural Concrete (slab), Plastering Works, Reinforcing Steel Bars, Fabricated Metal Roofing Accessory (gutter), Project Signboard (lgu-dipaculao), Occupational Safety And Health. F) Contract Duration: 60 C.d. G) Cost Of Bid Documents: 1000.00 Bidding Will Be Conducted Through Open Competitive Bidding Procedures In Accordance With R.a. 9184 And Its Revised Implementing Rules And Regulations (irr). Bids Received In Excess Of The Abc Shall Be Automatically Rejected At The Opening Of Bids. The Bidder Must Purchase Bid Documents And Must Meet The Following Major Criteria. A) Filipino Citizen Of 75% Filipino-owned Partnership, Corporation, Cooperative, Or Joint Venture With Pcab License Applicable To The Type And Cost Of The Contract. B) Completion Of At Least Two (2) Years Back Similar Contract Costing At Least 50% Of Abc To Be Bid. C) Net Financial Contracting Capacity At Least Equal To Abc Or Credit Line Commitment (clc) For At Least 10% Of Abc. The Bac Will Use Non-discretionary Pass/fail Criteria In The Eligibility Check And Preliminary Examination Of Bids. The Significant Times And Deadline Of Procurement Activities Are Shown Below: 1. Issuance Of Bidding Documents: January 6, 2025 – February 26, 2025, 8:00 A.m. To 5:00 P.m. 2. Pre Bid: February 12, 2025 9:00 Am Bac Office 3. Receipt Of Bids, February 26, 2025, 8:00 A.m. To 5:00 P.m. 4. Opening Of Bids, February 27, 2025, 9:00 A.m. Bac Office The Bac Will Issue Hand Copies Of Bidding Documents (bd’s) At The Bac Lgu-dipaculao, Aurora, Upon Payment Of Non-refundable Fee Stated Above For Bidding Documents. Bids Must Be Accompanied By A Bid Security, In The Amount And Acceptable Form, As Stated In Section 27-2 Of The Revised Irr. Prospective Bidders Shall Submit Their Duly Accomplishment Forms As Specified In The Bd’s In Two (2) Separate Sealed Bid Envelopes To The Bac Chairman. The First Envelop Shall Contain The Technical Component Of The Bid, Which Shall Include The Eligibility Requirements. The Second Envelop Shall Contain The Financial Component Of The Bid. Contract Will Be Awarded To The Lowest Calculated Responsive Bid As Determined In The Bid Evaluation And The Post Qualification. The Lgu-dipaculao Reserves The Right To Accept Or Reject Any Bid, To Annul The Bidding Process, And To Reject All Bids At Any Time Prior To Contract Award, Without Thereby Incurring Any Liability To The Affected Bidders. For Further Information, Please Refer To: Leticia F. Combis Bac-chairman Lgu-dipaculao Tel# (042)7145429 Noted: Danilo A. Tolentino Municipal Mayor

Details: Description Name Of Project: Improvement Of Multi-purpose Building Location: San Isidro, Libmanan, Camarines Sur Appropriation: P 100,000.00 Source Of Fund: Trust Fund – Cy 2024 Description : Dismantling And Restoration Concrete Works Masonry Works Roofing And Framing Works Steel Door Installation I. Dismantling And Restoration Estimated Quantity = 1.00 Lot Dismantling And Restoration Of Fence, And Concrete 1 Lot Chipping Ii. Concrete Works Estimated Quantity = 1.13 Cu.m, A.materials 11 Bags Cement 1 Cu.m, Washed Sand 2 Cu.m, 3/4” Crushed Gravel 3 Pcs 12mm Ørsb 8 Pcs 10mm Ørsb 1 Pc 1/4" Thk Ordinary Plywood 30 Bdft Formlumber 1 Kgs #16 Tie Wire 1 Kgs Assorted Cw Nail B. Labor C. Equipment Rental For 1 Day 1 Unit Concrete Bagger Mixer Iii. Masonry Works Estimated Quantity = 8.54 Sq.m. A.materials 113 Pcs 6” Chb 13 Bags Cement 1 Cu.m. Washed Sand 4 Pcs 10mm Ø Rsb 4 Pcs 8mm Ø Rsb 1 Kgs Tie Wire B. Labor Iv. Roofing And Framing Works Estimated Quantity = 1.00 Lot A. Materials 5 Pcs 2” X 2” X 1.5mm G.i. Tubular 3 Pcs 1/4 X 1 1/2” Angle Bar 14 Pcs 5/16” Expansion Bolt W/ Jacket 2 Pcs 10mm Square Bar 1 Pcs 2”x1/4” Thk Flat Bar 2 Pcs 4”x6”x12mm Ms Base Plate 3 Pcs 4”x4”x12mm Ms Base Plate 5 In.m. 0.6mm Thk Pre-painted Rib Type Long Span Roofing 2 Pcs Pre-painted Wall Flashing 8ft 0.6mm Thk 2 Pcs Pre-painted End Flashing 8ft 0.6mm Thk 4 Pcs 1/4 Thk Hardiflex 1 Box Blind Rivet 90 Pcs Tekscrew 10 Kgs Welding Rod 6 Pcs Cutting Disc 1 L Roof Sealant B. Labor C. Equipment Rental For 2 Days 1 Unit Welding Machine With Genset V. Steel Door Installation Estimated Quantity = 1.00 Lot A.materials And Labor (installation) 1 Unit Fabricated Steel Door (1m X 2.10m) 1” Ø G.i. Pipe Frame 10mm Square Bar Heavy Duty Lock Set Heavy Duty Hinge Spl I – Project Billboard 1 Pc Billboard With Frame (8ft X8ft) Spl Ii- Construction Safety & Health 3 Pcs Uniform 3 Pcs Hard Hat 3 Pcs Safety Boots 3 Pcs Gloves Spl Iii- Photographs 1 Lot Photographs Xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

Description: BOQ ITEMS: Earthwork in excavation in the following types of soil and rock up to and including 1.5 mtr. Lead including bailing or pumping out any water accumulating inside the excavated pit or trench shoring strutting adequate protection to be taken during excavation transporting the excavated soil for all lead stacking selectively including disposing off the rubbish rock fragments excess spoils etc. lead upto 100 Mtrs. in the area as directed by the Engineer all complete as per drawing specification and direction of the Engineer. , Earth work in back filling with available earth including watering and compaction at all elevations around foundations walls wells tunnels pitsculverts trenches road approaches and in plinth filling and area filling as per specifications and drawings and as directed by the Engineer with selected spoil within a lead of 100 mtr., Disposal carriage of rubbish waste rock earth etc.dumped stacked at site by mechanical means including loading unloading and dressing properly lead upto 5 Km. and up to any lift includind cost of all labours and equipments. , Surface dressing of the ground in all kinds of soil including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish lead up to 50 m and lift up to 1.5 m., Supply mix place in position compact cure cement concrete 1 cement 3 coarse sand 6 graded stone aggregate 20 mm nominal size below foundations walls wells pits trenches etc. and in basin lining as per specifications drawings and directions of the Engineer and including cost of centring and shuttering but excluding cost of cement., Supply mix place in position compact and cure including testing of concrete specimens finishing surfaces as per specifications drawings and directions of the Engineer of the following grades of concrete with 20mm and down graded stone aggregate and coarse sand in super structure or any level excluding cost of centring and shuttering cement and reinforcement. M20 RCC PCC, Taking delivery from store or departmental yard bend bind and place the following types of reinforcement in all types of reinforced concrete work at all elevations including cleaning straightening cutting bending and binding with 18 SWG annealed wire or with welding such as tack lap butt etc with approved electrodes providing concrete cover blocks pin chairsnails supports of reinforcement etc. with all materials and labour complete as per drawings specifications and directions of Engineer excluding cost of reinforcement. , Install dismantle and remove the form work of approved quality including splay recess corners haunch etc. scaffolding necessary rendering of concrete surfaces after exposure including cost of all material and labours at all elevations. , Supply and laying in position brick work with designate 75 bricks in super structure etc in cement coarse sand mortar 1 isto 6 including mixing mortar laying bricks raking joints curing etc complete with all materials and labour as per drawings and specifications excluding cost of cement. , Providing and fixing 125 into 63 mm M. S. Hinges of approved quality and make., Providing and fixing ISI marked anodised aluminium tower bolt black finish Barrel type with necessary screws etc. complete 300 into 10 mm, Providing and fixing ISI marked anodised aluminium tower bolt black finish Barrel type with necessary screws etc. complete 150 into10 mm, Providing and fixing bright finished brass hanging type floor door stopper with necessary screws etc. complete., Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer having brand logo with IS 3564 embossed on the body door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm with double speed adjustment with necessary accessories and screws etc. complete., Providing and fixing aluminium handles ISI marked anodised anodic coating not less than grade AC 10 as per IS 1868 transparent or dyed to required colour or shade with necessary screws etc. complete 125 mm., Providing and fixing aluminium sliding door bolts ISI marked anodised anodic coating not less than grade AC 10 as per IS 1868 transparent or dyed to required colour or shade with nuts and screws etc. complete 300x16 mm, Cement concrete flooring 1 cement 2 coarse sand 4 graded stone aggregate finished with a floating coat of neat cement including cement slurry but excluding the cost of nosing of steps etc. Complete as per direction of EIC excluding cost of cement. 40 mm thick with 20 mm nominal size stone aggregate, Grading roof for water proofing treatment with Cement concrete 1 cement 2 coarse sand 4 graded stone aggregate 20 mm nominal size excluding cost of cement., 15mm thick minimum plastering with 1 cement 6 coarse sand to all faces of walls channels in roof and other structures at various elevations including mixing laying finishing curing and necessary scaffolding work complete as per drawings specifications with all materials and labours excluding cement Including Making grove if required. Work will be done upto 10 m height., Applying neat cement punning including cost of all materials labours etc. Complete as per direction of Engineer in charge excluding cost of cement, Supplying and applying two or more coats of white wash with lime to walls ceiling etc. At various elevations including preparation of surfaces cleaning etc.complete with all materials labour scaffolding work as per specifications ., Supplying and applying two or more coats of approved water proof cement paint over a coat of primer to exterior surfaces of concrete masonry plastered surfaces etc.at all elevations and including preparation of surface necessary scaffolding work etc.complete with all materials and labour Application of paint should be made as per manufacturer specifications to give an even shade. , Drain cleaning including disposal of rubbish up to 5 km all complete as per direction of EIC, Cleanning of chajja roof RWDC Floor corner drains etc., Painting with synthetic enamel paint of approved brand and manufacturer of required colour to give an even shade two or more coats on new or old work over a priming coat complete as per specification and direction of EIC. , Providing and fixing factory made ISI marked steel glazed doors windows and ventilator with beading and all members complete of standard rolled steel sections joints mitred and flash butt welded and sash bars tenoned and riveted including providing and fixing of hinges pivots including priming coat of approved steel primer but excluding the cost of other fittings complete all as per approved design sectional weight of only steel members shall be measured for payment., Taking delivery from store or departmental yard fabrication and erection of Structural steel work riveted bolted or welded in built up sections trusses and framed work including cutting hoisting fixing in position and applying a priming coat of approved steel primer all complete., Providing and fixing bright finished brass casement window fastener with necessary screws etc. complete., Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc.15 mm dia nominal bore, Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc. 20 mm dia nominal bore, Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc.25 mm dia nominal bore, Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc. 50 mm dia nominal bore, Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc. 100 mm dia nominal bore G.I.or CPVC.., Fixing of old G.I. pipes complete with G.I. fittings including trenching and refilling etc. 15 mm dia nominal bore, Fixing of old G.I. pipes complete with G.I. fittings including trenching and refilling etc.20 mm dia nominal bore, Fixing of old G.I. pipes complete with G.I. fittings including trenching and refilling etc. 25 mm dia nominal bore, Providing and fixing C.P. brass bib cock or Pillar Cock of approved quality conforming to IS 8931. 15 mm nominal bore., Providing and fixing C.P. brass stop cock concealed of standard design and of approved make conforming to IS 8931. 15 mm nominal bore., Demolishing brick work in cement mortar manually or by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of EIC, Demolishing R.C.C or PCC work manually or by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of EIC, Dismantling G.I. pipes external work including excavation and refilling trenches after taking out the pipes manually by mechanical means including stacking of pipes within 50 metres lead as per direction of EIC upto 150 mm dia, Providing and fixing or Renewing glass panes with putty and nails wherever necessary including racking out the old putty Float glass panes of thickness 5.5 mm, Renewing of old glass putty, Supplying laying in position stone masonary with Hard rock boulder with cement morter 1 cement 6coarse sand morter finishing the top with PCC reasonably smooth complete with curing and raking of joints including cost of all material equipments and labour excluding cost of cement. , Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete., Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade Old work one or more coats, Providing and fixing 35 mm thick factory made PVC door shutters with frame 65mm into 55mm with wall thickness 2 mm all complete as per manufacturers specification and direction of EIC. , Providing and fixing ISI marked flush door shutters conforming IS 2202 non decorative type core of block board construction with frame of 1st class hard wood and well matched comercial 3 plyveneering with vertical grains or cross bands and face veneers on both faces of shutters 30 mm thick including ISI marked stainless steel butt hinges with necessary screws., Providing and fixing precoated galvanised iron profile sheets 0.50 mm total coated thickness with zinc coating 120 grams per sqm as per IS 277 in 240 mpa steel grade 5 microns epoxy primer on both side of the sheet and polyester top coat 15 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by EIC. The sheet shall be fixed using self drilling self tapping screws with EPDM seal complete upto any pitch in horizontal vertical or curved surfaces including ridges barge board etc excluding the cost of purlins rafters and trusses and including cutting to size and shape wherever required. , Providing and fixing Following precoated galvanised steel sheet roofing accessories 0.50 mm total coated thickness Zinc coating 120 grams per sqm as per IS 277 in 240 mpa steel grade 5 microns epoxy primer on both side of the sheet and polyester top coat 15 microns using self drilling self tapping screws complete in Ridges plain 500 mm, Providing and fixing Following precoated galvanised steel sheet roofing accessories 0.50 mm total coated thickness Zinc coating 120 grams per sqm as per IS 277 in 240 mpa steel grade 5 microns epoxy primer on both side of the sheet and polyester top coat 15 microns using self drilling self tapping screws complete in Barge board up to 300mm, Providing and fixing Following precoated galvanised steel sheet roofing accessories 0.50 mm total coated thickness Zinc coating 120 grams per sqm as per IS 277 in 240 mpa steel grade 5 microns epoxy primer on both side of the sheet and polyester top coat 15 microns using self drilling self tapping screws complete in Gutter. 600 mm over all girth, Providing reinforced by organic fibres or inorganic synthetic fibres cement 6 mm thick corrugated sheets roofing up to any pitch and fixing with polymer coated J or L hooks bolts and nuts 8 mm dia. G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc. complete excluding the cost of purlins rafters and trusses including cutting sheets to size and shape wherever required. , Providing and fixing Following fibre cement high impact polypropylene reinforced roofing accessories in all colours with polymer coated J or L hooks bolts and nuts and or G.I. seam bolts and nuts G.I. plain and bitumen washers or with self drilling fastener and EPDM washer etc. complete Close fitting adjustable ridges, Providing and fixing Following fibre cement high impact polypropylene reinforced roofing accessories in all colours with polymer coated J or L hooks bolts and nuts and or G.I. seam bolts and nuts G.I. plain and bitumen washers or with self drilling fastener and EPDM washer etc. complete in Barge boards , Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch including fixing bolts nuts 8mm dia. G.I plain bitumen washers complete but excluding the cost of purlins rafters trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum ultra violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pocketsThe sheets shall be opaque or translucent clear or pigmented textured or smooth as specified. 2 mm thick corrugated, Repairing and maitenance of Rolling shutter in all respect including greasing repairing replacement of material to repairing of rolling shutter. Supply and fixing 27.5 cm long springs, Supply and fixing ball bearing, Supply and fixing precast slab M20 grade, Providing wood work in frames of false ceiling or floor partitions etc. sawn and fixed in position Sal wood and 15 mm thick light weight integral densified micro look edged with PVC top matt false floor tiles of size 595 into 595 mm including cost of all materials labours and as per direction of EIC. , Aluminum work for shutters of doors windows ventilators including providing and fixing hinges pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber neoprene gasket required Fittings shall be paid for separately Polyester powder coated aluminium minimum thickness of polyester powder coating 50 micron, Providing and fixing water closet squatting pan Indian type W.C. pan with 100 mm sand cast Iron P or S trap 10 litre low level white P.V.C. flushing cistern including flush pipe with manually controlled device handle leverconforming to IS 7231 with all fittings and fixtures complete including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580 into 440 mm with integral type foot rests., Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 into 260 into 350 mm or 340 into 410 into 265 mm sizes respectively., Providing and fixing wash basin or Kitchen Sink with C.I. brackets 15 mm C.P. Brass pillar taps 32 mm C.P. brass waste of standard pattern including painting of fittings and brackets cutting and making good the walls wherever require White Vitreous China Wash basin size 630 into 450 mm with a single 15 mm C.P. brass pillar tap all complete as per direction of EIC., Providing and fixing white vitreous china water closet squatting pan Indian type Orissa pattern W.C. pan of size 580 into 440 mm, Supply and fixing PVC connecting pipe 15 mm N B, Supply and fixing PVC flexible waste pipe 32 or 40 mm N B, Supply and fixing float ball valve 20 mm N B, Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25 into 25 mm made of G.I. wire of dia 3 mm including strengthening with 2 mm dia wire or nuts bolts and washers as required complete as per the direction of EIC. , Dismantling steel work in built up sections in angles tees flats and channels including all gusset plates bolts nuts cutting rivets welding etc. including dismembering and stacking within 50 metres lead., Dismantling following roofing including ridges hips valleys and gutters etc.and stacking the material within 50 metres lead of G.S. Sheet, Dismantling following roofing including ridges hips valleys and gutters etc and stacking the material within 50 metres lead of Asbestos cement sheet

Details: Description Republic Of The Philippines Office Of The Punong Barangay Sagrada, Pili, Camarines Sur Bids And Awards Committee Contact No. +639857600284 Sagrada, Pili, Camarines Sur 4418 Invitation To Bid Rehabilitation And Improvement Of Multi-purpose Building/hall The Local Government Unit Of Sagrada, Pili, Camarines Sur Through The 20% Barangay Development Fund (bdf) (reprogrammed 2024) Intends To Apply The Sum Of Two Million Four Hundred Twenty Thousand Pesos (p2,420,000.00) Being The Approved Budget For The Contract (abc) To Payment Under The Contract For The Rehabilitation And Improvement Of Multi-purpose Building/hall. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. The Local Government Unit Of Sagrada, Pili Camarines Sur Now Invites Bids For The Rehabilitation And Improvement Of Multi-purpose Building/hall Is Required One Hundred Twenty Days (120 Day). Bidders Should Have Completed, Within 2 Years From The Date Of Submission And Receipt Of Bids, A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii Instructions To Bidders. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using A Non-discretionary “pass/fail” Criterion As Specified In The Implementing Rules And Regulations (irr) Of Republic Act (ra) 9184, Otherwise Known As The “government Procurement Reform Act”. A Complete Set Of Bidding Documents Maybe Purchased By Interested Bidders On January 21, 2025 To February 10, 2025 At 8:00 Am. From The Address Below And Upon Payment Of A Nonrefundable Fee For The Bidding Documents In The Amount Of Five Thousand Pesos (p5,000.00) Only. Bid Must Be Delivered To The Address Below On Or Before February 10, 2025 At 8:00 Am. At The Session Hall, Barangay Sagrada, Pili, Camarines Sur. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb. Bid Opening Shall Be On February 10, 2025 2:00 P.m. At The Session Hall, Barangay Sagrada, Pili, Camarines Sur. Bids Will Be Opened In The Presence Of The Bidders Representatives Who Choose To Attend At The Address Below. Late Bids Shall Not Be Accepted. The Local Government Unit Of Sagrada, Pili, Camarines Sur Reserves The Right To Accept Or Reject Any Bid, To Annul The Bidding Process, And To Reject All Bids At Any Time Prior To Contract Award, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. Part I. General Requirements B.5 Project Billboard/signboard Est. Qty. : 1 Each A. Labor 1 Construction Foreman 1 Skilled Laborer B. Equipment Handtools ( 5 % Of Labor) C. Materials 64 Sq.ft. Tarpauline (with Coa Format) 2 Pcs. 1/4" Marine Plywood 12 Pcs. 2" X 3" X 12' Coco Lumber 8 Pcs. 2" X 2" X 12' Coco Lumber 1 Kg. Assorted Cw Nails B.9 Mobilization/demobilization Est. Qty. : 1 L.s. 1 Lot Lump Sum Part Ii. Civil, Electrical, & Sanitary/plumbing Works A. Earthworks 801(1) Removal Of Structures And Obstruction Est. Qty. 1 L.s. A. Labor 1 Construction Foreman 5 Unskilled Laborer B. Equipment 1 Unit Jack Hammer Handtools ( 10 % Of Labor) C. Materials 803(1)a Structure Excavation (common Soil) Est. Qty. : 11.42 M3 A. Labor 1 Construction Foreman 5 Unskilled Laborer B. Equipment Handtools ( 10 % Of Labor) C. Materials 804(4) Gravel Fill Est. Qty. : 5 M3 A. Labor 1 Construction Foreman 5 Unskilled Laborer B. Equipment Handtools ( 5 % Of Labor) C. Materials 2 M3 Boulder (apple Size) 3 M3 G 1" Crushed Gravel B. Plain And Reinforced Concrete Works 900(1)c1 Structural Concrete, Class A, 28 Days Est. Qty. : 19.91 M3 A. Labor 1 Construction Foreman 2 Skilled Laborer 4 Unskilled Laborer B. Equipment 1 Unit Concrete Vibrator 1 Unit 1-bagger Mixer Minor Tools ( 10 % Of Labor) C. Materials 21 M3 G 3/4 "crushed Gravel 12 M3 Albay Sand 185 Bags Portland Cement 40 Bags Sahara 902(1)a Reinforcing Steel Bars, Grade 40 Est. Qty. : 3,491.67 Kgs. A. Labor 1 Construction Foreman 5 Skilled Laborer 6 Unskilled Laborer B. Equipment 1 Unit Bar Cutter, Single Phase (25 Mm Ø) 1 Unit Bar Bender Minor Tools ( 10 % Of Labor) C. Materials 125 Pcs. 10mm Ø Rsb 158 Pcs. 12mm Ø Rsb 185 Pcs. 16mm Ø Rsb 20 Pcs. 20mm Ø Rsb 135 Kgs. #16 G.i. Tie Wire 903(1) Formworks And Falseworks Est. Qty. : 1 L.s. A. Labor 1 Construction Foreman 1 Skilled Laborer 5 Unskilled Laborer Stripping 1 Construction Foreman 3 Unskilled Laborer B. Equipment 5 Sets H-frame 1.7m X 1.2m, Set 2 Pcs H-frames 4 Pcs Diagonal Cross Braces 4 Pcs Horizontal Braces 8 Pcs Joint Pins Minor Tools ( 10 % Of Labor) C. Materials 25 Pcs. 1/4" Marine Plywood 1,200 Bd.ft. Coco Lumber Consumables ( 5 % Of Material Cost) C. Finishing And Other Civil Works C.1. Fabricated Materials 1006(6) Steel Doors & Frame Est. Qty. 1 L.s. A. Labor Included In Material Cost B. Equipment Included In Material Cost C. Materials 1 Set D1 - Steel Grille Door (0.90m X 2.10m) (installed) (see Plan For Details) 1 Set D5 - Steel Fire Exit Door (installed) (see Plan For Details) 1010(2)a Flush Door Est. Qty. 1 L.s. A. Labor Included In Material Cost B. Equipment Included In Material Cost C. Materials 1 Set D2 - D2- 1/4" Thk. Marine Plywood Flush Door With 2" X 5" (installed) (see Plan For Details) 1007(1)b Aluminum Framed Glass Windows Est. Qty. 1 L.s. A. Labor Included In Material Cost B. Equipment Included In Material Cost C. Materials 1 Set D2 - D3- 1/4" Thk. Tinted Tempered Glass On Powder Coated Alum. Framed Swing Door (installed) (see Plan For Details) 1043(2) Pvc Doors And Frames Est. Qty. 1 L.s. A. Labor Included In Material Cost B. Equipment Included In Material Cost C. Materials 1 Set W1- Awning Window With 1/4" Thk. Tinted Glass On Powder Coated Alum. Framed With Fixed Glass (installed) (see Plan For Details) 1008(2) Aluminum Glass Windows Est. Qty. 1 L.s. A. Labor Included In Material Cost B. Equipment Included In Material Cost C. Materials 1 Set W1- Awning Window With 1/4" Thk. Tinted Glass On Powder Coated Alum. Framed With Fixed Glass (installed) (see Plan For Details) 6 Sets W2- Awning Window With 1/4" Thk. Tinted Glass On Powder Coated Alum. Framed With Fixed Glass (installed) (see Plan For Details) 3 Sets W3- Awning Window With 1/4" Thk. Tinted Glass On Powder Coated Alum. Framed With Fixed Glass (installed) (see Plan For Details) 1 Set W5- Awning Window With 1/4" Thk. Tinted Glass On Powder Coated Alum. Framed (installed) (see Plan For Details) 1 Set W6- Awning Window With 1/4" Thk. Tinted Glass On Powder Coated Alum. Framed (installed) (see Plan For Details) 1009(2) Jalousie Window Est. Qty. 1 L.s. A. Labor Included In Material Cost B. Equipment Included In Material Cost C. Materials 1 Set W4- Tinted Glass Jalousie Window Blades On Anolok Alum. Framing (jalou Plus)(installed) (see Plan For Details) C.2. Carpentry And Joinery Works 1003(1)a1 4.5mm Fiber Cement Board On Metal Frame Ceiling Est. Qty. 59.75 M2 A. Labor 1 Construction Foreman 2 Skilled Laborer 3 Unskilled Laborer B. Equipment Minor Tools ( 10 % Of Labor) C. Materials 23 Pcs. 4.5 Mm. Hardieflex Sheet (1.2 M. X 2.4 M.) 69 Pcs. Double Metal Furring 22 Pcs. Carrying Channel 60 Pcs. Hanger Bars/rod 359 Pcs. Wall Clip 15 Pcs. Wall Angle 2 Box Blind Rivet (500pcs/box) 239 Pcs. 1" Metal Screw Consumables ( 5 % Of Material Cost) 1003(4) Cabinets Est. Qty. 1 L.s. A. Labor 1 Construction Foreman 3 Skilled Laborer 3 Unskilled Laborer B. Equipment Minor Tools ( 10 % Of Labor) C. Materials 1 Set Wall Counter With Cabinet 2 Pcs. Fabrication Of Conference Tables (60cm X 190cmx78cm High) 1 Pc. Fabrication Of Conference Tables (60cm X 200cmx78cm High) C.3. Masonry Works 1003(1)a1 100mm Chb Non-load Bearing (including Reinforcing Steel) Est. Qty. 73.02 M2 A. Labor 1 Construction Foreman 3 Skilled Laborer 4 Unskilled Laborer B. Equipment Minor Tools ( 10 % Of Labor) C. Materials 959 Pcs. 100 Mm Thk Chb (non-load Bearing) 44 Bags Portland Cement 5 M3 Albay Sand 66 Pcs. 10mm Ø Rsb 9 Kgs. #16 G.i. Tie Wire C.4. Finishes 1027(1) Plain Cement Plaster Finish Est. Qty. 269.94 M2 A. Labor 1 Construction Foreman 2 Skilled Laborer 3 Unskilled Laborer B. Equipment Minor Tools ( 10 % Of Labor) C. Materials 95 Bags Portland Cement 13 M3 Albay Sand 1018(6) Textured Glazed Tiles Est. Qty. 12.60 M2 A. Labor 1 Construction Foreman 2 Skilled Laborer 5 Unskilled Laborer B. Equipment Minor Tools ( 10 % Of Labor) C. Materials 83 Pcs. 400 X 400 Glazed Floor Tiles Non Skid 8 Bags Portland Cement 1 M3 Albay Sand 2 Bags Tile Grout (2kg.) 2 Bags Tile Adhesive (25 Kgs.) Consumables ( 5 % Of Material Cost) 1018(3) Granite Tiles Est. Qty. 23.45 M2 A. Labor 1 Construction Foreman 3 Skilled Laborer 1 Unskilled Laborer B. Equipment Minor Tools ( 10 % Of Labor) C. Materials 69 Pcs. 600 X 600 Glazed Floor Tiles Non Skid 8 Bags Portland Cement 1 M3 Albay Sand 4 Bags Tile Grout (2kg.) 4 Bags Tile Adhesive (25 Kgs.) Consumables ( 5 % Of Material Cost) 1018(1) Glazed Tiles Est. Qty. 14.84 M2 A. Labor 1 Construction Foreman 2 Skilled Laborer 3 Unskilled Laborer B. Equipment Minor Tools ( 10 % Of Labor) C. Materials 99 Pcs. 400 X 400 Ceramic Glazed Floor Tiles 5 Bags Portland Cement 1 M3 Albay Sand 2 Bags Tile Grout (2kg.) 3 Bags Tile Adhesive (25 Kgs.) Consumables ( 5 % Of Material Cost) 1018(2) Unglazed Tiles Est. Qty. 2.65 M2 A. Labor 1 Construction Foreman 2 Skilled Laborer 5 Unskilled Laborer B. Equipment Minor Tools ( 10 % Of Labor) C. Materials 18 Pcs. 400 X 400 Ceramic Unglazed Floor Tiles 1 Bags Portland Cement 1 M3 Albay Sand 1 Bags Tile Grout (2kg.) Consumables ( 5 % Of Material Cost) C.5. Paint Works 1032(1)a Painting Works (masonry Painting) Est. Qty. 329.59 M2 A. Labor 1 Construction Foreman 3 Skilled Laborer 8 Unskilled Laborer B. Equipment Minor Tools ( 10 % Of Labor) C. Materials 8 Gal. Concrete Neutralizer 14 Gal. Concrete Sealer/primer 17 Gal. Patching Compound 17 Bags Skim Coat 8 Pail Semi-gloss Paint Consumables ( 5 % Of Material Cost) 1032(1)c Painting Works (metal Painting) Est. Qty. 1 L.s. A. Labor 1 Construction Foreman 3 Skilled Laborer 3 Unskilled Laborer B. Equipment Minor Tools ( 10 % Of Labor) C. Materials 2 Gal. Red Oxide Primer 16 Gal. Enamel Paint 9 Gal. Paint Thinner Consumables ( 5 % Of Material Cost) C.6. Steel Works 1047(1) Structural Steel Est. Qty. 1 L.s. A. Labor 1 Construction Foreman 4 Skilled Laborer 5 Unskilled Laborer B. Equipment 1 Welding Machine, Electric Driven Minor Tools ( 10 % Of Labor) C. Materials 8 Pcs. 2" X 4"x 6m Steel Channel 10 Pcs. 3/16" X 2" X 2" X 20' Angle Bar 25 Pcs. 1/8" X 1 1/2" X 2" X 20' Angle Bar 3 Pcs. 3/16" X 2" X 20' Flat Bar 23 Pcs. 2" X 4" X 20' Steel Purlins (1.5mm) 14 Kgs. Welding Rod Consumables ( 5 % Of Material Cost) C.7. Roofing Works 1013(1) Corrugated Metal Roofing Est. Qty. 55.04 M2 A. Labor 1 Construction Foreman 3 Skilled Laborer 6 Unskilled Laborer B. Equipment 1 Welding Machine, Electric Driven Minor Tools ( 10 % Of Labor) C. Materials 20 Pcs. #26 X 1m X 5m, 5 Rib Type Roof (pre-painted) 10 Pcs. #26 X 8' Plain G.i. Gutters 15 Pcs. #26 G.i. Fascia, 8' 10 Pcs. 1/2" X 10" X 10' Hardi Senepa 2,000 Pcs. Metal Tekscrew 9 Boxes 1/8" Ø X 1/2" Blind Rivets 7 Box 3/16" Ø X 1/2" Blind Rivets 68 Mts. 10mm Thk. Insulation Roof Blanket 14 Pcs. P.g.i. Gutter Straps & Supports Consumables ( 5 % Of Material Cost) D. Plumbing/sanitary Works 1002(4) Sanitary/ Plumbing Fixtures Est. Qty. 1 L.s. A. Labor 1 Construction Foreman 4 Skilled Laborer 4 Unskilled Laborer B. Equipment Minor Tools ( 10 % Of Labor) C. Materials 1 Set Water Closets, Brauhm, White With Bidette And Complete Accessories 1 Set Lavatory, Brauhm Or Hcg, Counter Type White With Drain Accessories & Faucet & Supply Accessories 1 Set Urinal, White Hcg, Complete With Drain Accessories And Water Supply Fittings And Accessories. 2 Pc 4 X 4 Ss Floor Drins With Strainer 1 Pc Ss Faucet 1 Set 10" Exhaust Fan (ceiling Type) 1 Pc. 70cm X 80 Cm Facial Mirror 2 Rolls Teflon Tape 1001(9) Storm Drainage And Downspout Est. Qty. 1 L.s. A. Labor 1 Construction Foreman 4 Skilled Laborer 3 Unskilled Laborer B. Equipment Minor Tools ( 10 % Of Labor) C. Materials 10 Pcs. 3"ø X 10" Pvc Pipe 12 Pcs. 3"ø X 45° Pvc Elbow 3 Pcs. 3"ø X 90° Pvc Elbow 18 Pcs. 3"ø Pipe Straps And Accessories 3 Pcs. 3"ø Ss, Downspout Strainer 1 Liter Solvent 1002(24) Waterline Works Est. Qty. 1 L.s. A. Labor 1 Construction Foreman 2 Skilled Laborer 2 Unskilled Laborer B. Equipment Minor Tools ( 10 % Of Labor) C. Materials 8 Pcs. 3/4"ø X 4m, Ppr Pipes, (#16) 4 Pcs. 1/2"ø X 4m, Ppr Pipes, (#16) 2 Pcs. 3/4"ø Gate Valve, Ppr 8 Pcs. 3/4"ø Elbow Ppr 15 Pcs. 1/2"ø Elbow Ppr 4 Pcs. 3/4" X 1/2" Ppr Tee Reducer 4 Pcs. 1/2"ø Ppr Threaded Tee 5 Pcs. 1/2" Ø Cap 3 Pcs. 3/4 X 1/2" Couplings 2 Liter Solvent 1001(8) Sewerline Works Est. Qty. 1 L.s. A. Labor 1 Construction Foreman 4 Skilled Laborer 5 Unskilled Laborer B. Equipment Minor Tools ( 10 % Of Labor) C. Materials 6 Pcs. 4"ø X 3m Pvc Pipe 3 Pcs. 3"ø X 3m Pvc Pipe 4 Pcs. 2"ø X 3m Pvc Pipe 2 Pcs. 2"ø Ordinary P-trap With Clean Out 1 Pcs. 4"ø X 90° Pvc Elbow 2 Pcs. 4"ø X 45° Pvc Elbow 5 Pcs. 4"ø X 4"ø Pvc Tee 5 Pcs. 4"ø X 3"ø Coupling Reducer 5 Pcs. 3"ø Clean Out 1 Pcs. 4"ø X 2"ø Pvc Tee 3 Pcs. 4"ø X 3"ø Pvc Wye 3 Pcs. 4"ø X 4"ø Pvc Wye 3 Pcs. 2"ø X 2"ø Pvc Tee 8 Pcs. 2"ø X 2"ø X 90° Pvc Elbow 1 Pcs. 3"ø X 2"ø Pvc Tee 2 Pcs. 3"ø X 45° Pvc Elbow 2 Liter Solvent E. Electrical Works 1100(10) Conduit Boxes And Fittings Est. Qty. 1 L.s. A. Labor 1 Construction Foreman 3 Skilled Laborer 8 Unskilled Laborer B. Equipment 1 Unit Electric Edger/grinder 1 Unit Electric Drill C. Materials 60 Pcs. 1/2"ø X 10' Pvc, Pns Conduit Pipe 10 Pcs. 3/4"ø X 10' Pvc, Pns Conduit Pipe 42 Pcs. Octagonal Junction Box Gauge #16 Deep Type (101mm X 101mm X 53mm) 24 Pcs. Utility Box Gauge #16, Deep Type (50mm X 101mm X 53mm) Consumables ( 5 % Of Material Cost) 1101(33) Wires And Wiring Devices Est. Qty. 1 L.s. A. Labor 1 Construction Foreman 1 Skilled Laborer 1 Unskilled Laborer B. Equipment 1 Unit Electric Edger/grinder 1 Unit Electric Drill C. Materials 150 M. 2.0mm² Thhn Wires, Stranded 100 M. 3.5mm² Thhn Wires, Stranded 60 M. 5.5mm² Thhn Wires, Stranded 30 M. 8.0mm² Thhn Wires, Stranded 3 Sets Single Pole Swtch With Plate 2 Sets 2-gang Switch With Plate 4 Sets 3-gang Switch With Plate 14 Pcs. Duplex Convenience Outlet, Grounding Type (unversal),240v 2 Pcs. Special Purpose Outlet, Grounding Type (unversal),240v Consumables ( 5 % Of Material Cost) 1102(1) Panelboard With Main & Branch Breakers Est. Qty. 1 L.s. A. Labor 1 Construction Foreman 1 Skilled Laborer 2 Unskilled Laborer B. Equipment 1 Unit Electric Edger/grinder 1 Unit Electric Drill C. Materials 1 Set 70 At, 2p, 230v Circuit Breaker 2 Sets 30 At, 2p, 230v Circuit Breaker 2 Sets 20 At, 2p, 230v Circuit Breaker 2 Sets 15 At, 2p, 230v Circuit Breaker 1 Set 8-hole Panel Board Consumables ( 5 % Of Material Cost) 1103(1) Lighting Fixtures Est. Qty. 1 L.s. A. Labor 1 Construction Foreman 4 Skilled Laborer 6 Unskilled Laborer B. Equipment 1 Unit Electric Edger/grinder 1 Unit Electric Drill C. Materials 5 Sets Chandelier, Small Type 12 Sets Pinlights, 3"ø 6 Watts, Dl 17 Sets Pinlights, 3 1/2"ø 9 Watts, Dl 2 Sets Pinlights, 3 1/2"ø 14 Watts, Dl, Tiltable 4 Sets Pinlights, 11 Watts, Dl 4 Sets Cove Lights, 3m Long, Tri-color 3 Sets Wall Bracket Lights 2 Sets Emergency Lights F. Mechanical Works 1200(13) Airconditioning Est. Qty. 1 L.s. A. Labor B. Equipment C. Materials 1 Set 2.0hp Wall Mounted Type Inverter (installed) 1 Set 1.0hp Wall Mounted Type Inverter (installed) Pre-bid - January 28, 2025, 1:00pm Bid Evaluation - February 12, 2025 Post-qualification - February 14, 2025 Notice Of Award - February 17, 2025 Notice To Proceed - February 20, 2025 For Further Information, Please Refer To: Abel B. Hernandez Bac Chairman/ Brgy. Kagawad Lgu-sagrada, Pili, Camarines Sur +639857600284

Details: Description Invitation To Bid 1. The Provincial Government Of Misamis Oriental, Through The 20% Df Intends To Apply The Sum Of Three Million Nine Hundred Twenty Four Thousand Two Hundred Seventeen And 29/100(php 3,924,217.29) Being The Approved Budget For The Contract Abc To Payments Under The Contract For Construction Of Child Development Center, Brgy. Solana, Jasaan, Misamis Oriental, Under Purchase No. 0051-25 Dated November 13, 2024. Description Of Works Part I Other General Requirements B.3(1) Permits And Clearances B.5(1) Project Billboards/signboard B.7(1) Occupational Safety And Health Program B.9(1) Mobilization/demobilization B.26(11) Signages Part Ii Civil , Plumbing And Electrical Works Part A Earthworks 801(1) Removal Of Structures And Obstruction 803(1)a Structure Excavation (common Soil) 804(1)a Embankment( From Structure Excavation) 804(7) Gravel Fill Part B Termite Control 1000(1) Soil Poisoning Part C Plain And Reinforced Concrete Works 900(1)c Structural Concrete (class A, 28 Days) 902(1)a1 Reinforcing Steel (deformed) Grade 40 903(2) Formworks And Flaseworks Part D Finishing And Other Civil Works D.1 Masonry Works 1046(1)a2 Chb Non Load Bearing ( Including Reinforcing Steel, 150mm) 1046(2)a1 Chb Non Load Bearing ( Including Reinforcing Steel, 100mm) D.2 Doors And Windows 1004(2) Finishing Hardware 1008(1)c Aluminum Glass Window (awning Type) 1009(1)a Jalousie Window 1010(1) Frames, Jambs, Sills, Head, Transoms And Mullions 1010(2)a Hollow Core Flush Door 1010(2)b Wooden Panel Door D.3 Finishing, Carpentry And Joinery Works 1003(11)a1 Fascia Board (fiber Cement Board) 1003(17) Carpentry And Joinery Works (cabinets) 1003(17) Carpentry And Joinery Works (ceiling) 1003(23) Modular Partition 1018(2) Unglazed Tiles 1018(5) Glazed Tiles 1021(1)a Plain Cement Floor Finish 1027(1) Cement Plaster Finish D.4 Painting Works 1032(1)a Painting Works (masonry/concrete) 1032(1)b Painting Works (wood) 1032(1)c Painting Works (steel) D.5 Roof Framing And Roofing Works 1013(2)c Fabricated Metal Roofing Accessory (gutters, Gauge 24) 1013(2)f Fabricated Metal Roofing Accessory (end Flashing/ridge) 1014(1)b2 Pre-painted Metal Sheets (rib-type, Long Span) 1036(1)c Polycarbonate Sheets, Multi Wall 1038(1) Reflective Insulation 1047(1) Structural Steel 1047(2)b Structural Steel Roof Truss 1047(2)c Structural Steel Purlins 1051(1) Metal Railing Part E Plumbing Works 1001(5)b Catch Basin (chb) 1001(8) Sewer Line Works 1001(11) Septic Vault 1002(4) Plumbing Fixtures 1002(20) Facial Mirror 1002(24) Cold Water Lines Part F Electrical Works 1100(10) Conduit, Boxes And Fittings Conduit Works/conduit Rough-ins 1101 Wires And Wiring Devices 1102 Power Load Center, Switch Gear And Panel Boards 1103 Lighting Fixtures Part G Fire Alarm System 1208 Fire Alarm System Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. 2. The Provincial Government Of Misamis Oriental Now Invites Bids For The Above Procurement Project. Completion Of The Works Is Required 66 Calendar Days Bidders Should Have Completed A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii (instruction To Bidders). 3. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using A Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) No. 9184. 4. Interested Bidders May Obtain Further Information From Bids And Awards Committee Thru The Bac Secretariat At The Procurement Unit, Capitol Building, Cagayan De Oro City And Inspect The Bidding Documents At The Address Given Below During [8:00am-5:00 Pm]. 5. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders On [january 23, 2025 To February 12, 2025; 8:00-3:00 Pm] From The Given Address And Website(s) Below Bids And Awards Committee Thru The Bac Secretariat At The Procurement Unit, Capitol Building, Cagayan De Oro City And Upon Payment Of The Applicable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb, In The Amount Of [php5,000.00]. The Procuring Entity Shall Allow The Bidder To Present Its Proof Of Payment. 6. The Provincial Government Of Misamis Oriental Will Hold A Pre-bid Conference On January 30, 2025;10:30am At The Bids And Awards Committee Office, 2nd Floor Capitol Building, Cagayan De Oro City, Which Be Open To Prospective Bidders 7. Bids Must Be Duly Received By The Bac Secretariat Through Manual Submission At The Office Address Bids And Awards Committee Office, Conference Room, 2nd Floor, Capitol Building, Cagayan De Oro City On Or Before February 13, 2025;10:00am. Late Bids Shall Not Be Accepted. 8. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 14. 9. Bid Opening Shall Be On February 13, 2025; 10:30am At The Given Address Bids And Awards Committee Office, Conference Room, 2nd Floor, Capitol Building, Cagayan De Oro City. Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend The Activity. 10. The Provincial Government Of Misamis Oriental Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Irr Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 11. For Further Information, Please Refer To: Ms. Jacquiline M. Noble Head, Bac Secretariat C/o Procurement Unit Capitol Building Cagayan De Oro City. Bacmisamisoriental@gmail.com Www.misamisoriental.gov.ph Filemon R. Aguilar, Jr. Bac, Chairman

Details: Description Invitation To Bid For The Procurement Of 1 Lot Electrical Materials And Supplies For Installation Of Additional 50kva Distribution Transformer, Upgrading Of Service Entrance/main Circuit Breaker And Repair Of The Existing 50kva Transformer - 1st Posting (itb No. 03-goods-2025) 1. The Local Government Unit Of Sta. Cruz, Davao Del Sur, Through The Special Education Fund For The 2025 Intends To Apply The Sum Of Three Hundred Fourty Thousand Four Hundred Ninety Pesos (php 340,490.00) Being The Abc To Payments Under The Contract For Procurement Of 1 Lot Electrical Materials And Supplies For Installation Of Additional 50kva Distribution Transformer, Upgrading Of Service Entrance/main Circuit Breaker And Repair Of The Existing 50kva Transformer - 1st Posting. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. Item No. Qty Unit Of Issue Item Description Approved Budget For The Contract (abc) 1 1 Unit Distribution Transformer 50kva,13.2/7.620kv, 120/240v, 60hz. 1 Phase, Oil Immersed Pole Type 150,000.00 2 1 Set Fuse Cut-out And Arrester Combination, 15kv Bil 100a Capacity With Lighting Arrester 9-10 Kv Mcov 8,500.00 3 3 Pcs Fuse Link 6 Amperes 1,500.00 4 1 Unit Hot Line Clamp 100a Capacity 750.00 5 1 Set Transformer Hanger: 2 Mounting Bracket, 4 4,500.00 6 2 Sets Fabricated Secondary Rack, 3 Spools W/ Spool 1,600.00 7 120 Mts Thw Strd. Wire 100 Mm Sq. 132,000.00 8 4 Pcs Twin Bolt, Cooper 100 Mm Square 4,000.00 9 2 Pcs Twin Bolt, Cooper 200 Mm Square 2,400.00 10 1 Pc Entrance Cap 40mm Dia. 150.00 11 1 Length Rsc Pipe 40mm Dia 510.00 12 1 Pc Lock Nut & Bushing 40mm Dia. 70.00 13 1 Pc G.i Nipple 40mm X 5 120.00 14 2 Units Fabricated Secondary Rack, 2 Spools W/ Spool 1,400.00 15 110 Mts Service Drop Wire No. 4 12,100.00 16 1 Set Nema 1 Circuit Breaker Enclosure With 225a, 2p 12,000.00 17 5 Rolls Electrical Tape (big) 350.00 18 1 Roll Rubber Tape 150.00 19 10 Pcs Spool Insulator 400.00 20 2 Bags Portland Cement 600.00 21 2 Kls Tire Wire 16 200.00 22 2 Lengths Drb 12mm X 6m 480.00 23 6 Bags Coarse Sand 210.00 24 1 Length G.i Pipe 3 Inches Dia. S-40 3,800.00 25 1 Length Angle Bar 2x3/16 900.00 26 10 Pcs Cutting Disc 2 Metal 500.00 27 4 Kls Welding Rod Special 6013 800.00 28 1 Pc Paint Brush 2 50.00 29 1 Quart Aluminum Paint 350.00 30 2 Bot Lacquer Thinner 100.00 Total 340,490.00 2. The Local Government Unit Of Sta. Cruz, Davao Del Sur Now Invites Bids For The Above Procurement Project. Delivery Of The Goods Is Required At Fifteen (15) Days From Receipt Of Notice To Proceed. Bidders Should Have Completed, Within Two Years From The Date Of Submission And Receipt Of Bids, A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii (instructions To Bidders). 3. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using A Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) No. 9184. Bidding Is Restricted To Filipino Citizens/sole Proprietorships, Partnerships, Or Organizations With At Least Sixty Percent (60%) Interest Or Outstanding Capital Stock Belonging To Citizens Of The Philippines, And To Citizens Or Organizations Of A Country The Laws Or Regulations Of Which Grant Similar Rights Or Privileges To Filipino Citizens, Pursuant To Ra No. 5183. 4. Prospective Bidders May Obtain Further Information From The Bac Secretariat Office At Old Municipality Of Sta. Cruz Hall Compound, Sta. Cruz, Davao Del Sur And Inspect The Bidding Documents At The Address During Weekdays Starting From 8:00 O’clock In The Morning To 5:00 O’clock In The Afternoon. 5. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders On Friday, January 24, 2025 From The Given Address Below And Website(s) Below And Upon Payment Of The Applicable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb, In The Amount Of Five Hundred (php 500.00) Pesos. 6. Bids Must Be Duly Received By The Bac Secretariat Through Manual Submission At The Office Address Indicated Below, On Or Before 9:30 O’clock In The Morning Of Tuesday, February 4, 2025. Late Bids Shall Not Be Accepted. 7. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 14. 8. Bid Opening Shall Be On 9:40 O’clock In The Morning Of Tuesday, February 4, 2025 At The Given Address Below. Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend The Activity. 9. The Local Government Of Unit Of Sta. Cruz, Davao Del Sur Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Irr Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 10. For Further Information, Please Refer To: Ommi Kharzom L. Buat Bac Head Secretariat Bac Secretariat Office, New Municipal Hall Of Sta. Cruz, Davao Del Sur. 09107650089 - E-mail Address:bac5stacruz@gmail.com Engr. Ray R. Sealana Bac Chairperson, Municipal Assessor

Details: Description Invitation To Bid For Construction Of Senior Citizen's Building At Mahal Na Pangalan, Calapan City, Oriental Mindoro 1. The Provincial Government Of Oriental Mindoro (pgom), Through The Sb No. 2 - 20% Df 2024 Intends To Apply The Sum Of One Million Five Hundred Fifty Seven Thousand Four Hundred Fifty Three Pesos And 78/100 (php 1,557,453.78) Being The Approved Budget For The Contract (abc) To Payments Under The Contract For “construction Of Senior Citizen's Building At Mahal Na Pangalan, Calapan City, Oriental Mindoro (ib No. Cw-2025-024)”. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. 2. The Provincial Government Of Oriental Mindoro (pgom) Now Invites Bids For The Above Procurement Project. Completion Of The Works Is Required 55 Calendar Days. Bidders Should Have A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii (instructions To Bidders). Item No. Description Qty/unit B.5 801(1) 803(1)a 804(1)b 804(4) 900(1)c2 900(1)c3 900(1)c4 900(1)c6 902(1)a 903(2) 1046 (2) A1 1004(2) 1008(2) 1010(2)a 1010(2)b Spl 1003(1)a1 1018(5) 1018(2) 1027 (1) 1051(6) Spl-2 1032(1)a 1032(1)b 1032 (1) С 1032 (2) 1013(2)a2 & 1013(2)b1 1014(1)b2 1047(2)a, 1047(2)b 1047(10) 1001(10) & 1002(24) 1002(4) 1001(11) 1100 (10) 1101(33) 1102 (1) 1103(1) 1005(6) Project Billboard/sign Board Removal Of Structures And Obstruction Structure Excavation (common Soil) Embankment From Borrow Gravel Fill Structural Concrete (footing And Slab On Fill), Class A, 28 Days Structural Concrete (footing Tie Beam), Class A, 28 Days Structural Concrete (column), Class A, 28 Days Structural Concrete (beams/girders), Class A, 28 Days Reinforcing Steel (deformed), Grade 40 Formworks And Falseworks 100mm Chb Non-load Bearing (including Reinforcing Steel) Finishing Hardwares Aluminum Glass Windows Wooden Flush Door Wooden Panel Door Aluminum Doors 4.5mm Fiber Cement Board Ceiling On Metal Frame Ceiling Glazed Tiles Unglazed Tiles Cement Plaster Finish Railings Fabricated Concrete Signage Painting Works, Masonry, Concrete & Ceiling Painting Works, (wood Painting) Painting Works, Steel Varnishing Works Fabricated Metal Roofing Accessory Prepainted Metal Sheets, Long Span, Above 0.427mm, Rib Type Structural Steel, Trusses & Purlins Metal Structure Accessories Pipes With Connection & Cold Water Lines Plumbing Fixtures Septic Vault (concrete/chb) Conduit, Boxes, And Fittings (conduit Works/conduit Rough-in) Wires And Wiring Devices Panelboard With Main & Branch Breakers Lighting Fixtures And Lamps Window Accessory 1.00 Ea 1.00 I.s. 28.11 M3 20.90 M3 2.61 M3 10.22 M3 2.43 M3 3.61 M3 3.10 M3 2,538.09 Kg 140.67 M2 201.06 M2 1.00 I.s 1.00 I.s 3.36 M2 1.89 M2 1.00 I.s. 54.63 M2 12.85 M2 42.38 M2 340.91 M2 1.00 I.s 1.00 I.s. 339.95 M2 6.72 M2 66.66 M2 3.78 M2 49.00 M 52.25 M2 685.75 Kg 1.00 L.s 1.00 L.s 1.00 L.s 1.00 L.s 1.00 L.s 1.00 L.s 1.00 L.s 1.00 L.s 1.00 L.s 3. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) No. 9184. Bidding Is Restricted To Filipino Citizens/sole Proprietorships, Cooperatives, And Partnerships Or Organizations With At Least Seventy Five Percent (75%) Interest Or Outstanding Capital Stock Belonging To Citizens Of The Philippines. 4. Interested Bidders May Obtain Further Information From Bids And Awards Committee Of The Pgom And Inspect The Bidding Documents At The Address Given Below From 8:00 A.m. To 5:00 P.m. Of Mondays To Fridays. 5. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders On January 20, 2025 To February 03, 2025 From Given Address Below And Upon Payment Of The Applicable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb, In The Amount Of Five Thousand Pesos (php 5,000.00). The Procuring Entity Shall Allow The Bidder To Present Its Proof Of Payment For The Fees In Person. 6. The Pgom Will Hold A Pre-bid Conference On January 20, 2025 At 9:00 A.m. At Bac Conference Room, Provincial Capitol Complex, Camilmil, Calapan City, Oriental Mindoro Which Shall Be Open To Prospective Bidders. 7. Bids Must Be Duly Received By The Bac Secretariat Through Manual Submission At The Office Address As Indicated Below On Or Before February 03, 2025 At 8:30 A.m. Late Bids Shall Not Be Accepted. 8. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 16. 9. Bid Opening Shall Be On February 03, 2025 At 9:00 A.m. At Bac Conference Room, Provincial Capitol Complex, Camilmil, Calapan City, Oriental Mindoro. Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend At The Activity. 10. The Pgom Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Implementing Rules And Regulations (irr) Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 11. For Further Information, Please Refer To: Engr. Jollie Ver E. Lasic Head, Bac Secretariat Pgo – Procurement Division Provincial Capitol Complex Camimil, Calapan City, Oriental Mindoro (january 20, 2025) Atty. Earl Ligorio R. Turano Ii Bac Chairperson