Fabrication Tenders

Description: Repair/fabrication/supply Works Of 48(forty Eight) Items For Different Type Of Equipment Of Zonal Workshop-c.

Description: Cutting, Threading, Welding & Joint, Leth Fabrication, Turning Etc. Under Phed City Sub Div. Gangapur City, Distt.- Sawai Madhopur

Description: CATEGORY: Indoor LED Video Wall Display , Video controller for LED main display , HDMI AV extender , Installation Charges Video Wall Systems , Mechanical cum Civil Fabrication work for Video wall

Description: Pl No.98050126] Scrap Cond./released/unserviceable Ms Scrap Such As Cbc Coupler Bodies, Angels Channels, Signal Rods, Dash Pot, Yokes, Draft Gears Sets, Ms Sheets, Winch For Lc Gate, Lever Lock, Lever Rods, Pull Rods, Suspension Tube, Housing Axle Bearing, Chequered Plates, Cbc Operating Handle, Rel Hook, Anti Roll Bracket, Ms Radiator, Wheel Stand, Dradger Drum, Ms Stool, Centring Disc, Ms Liners, Center Pivot Washer, Brake Shoe Head, Center Pivot Ring, Side Frame Key, Adopter Narrow Jaw, Anti Roll Bar, Bolts & Nuts, Wear Plate, Adopter Wide Jaw, Suspension Rods ,equalizing Stay, Erc Clips, Wagon Doors, Rail Flange, Chain Hook,hydraulic Motor, Pipe Fittings, Rotary Shield With Bearings, Sab Parts, Ls Beam, Hangers, Brake Levers, Brake Hangers, Ms Plates Of Elastomeric Pad, Adapter Broken, Center Pivot Top, Anvil, Workdout Sab, Gib Crane, Bracket, Plate Screws, Knuckle, Fabricated Test Rig, Gear Wheel, Anchor Link, Brake Beam, Axle Box Housing, Bearing Plates, Rivette, Chirr Plate, Ms Bed Plate, Ms Guage Tie Plate, Structure Bar, Ms Tie Plates, Slide Chaires, Brake Shoe Head, Locking Plate, Long Pull Rod, Operating Handle, Cbc Lock, Cbc Yoke, Lower Spring Sheet Beam, Center Beams, Center Pivot Washer, Screw Couplings, Pipes, Buffer Plungers, Buffer Casings, Draw Gear Hooks, Silent Blocks, Cut Off Sheets, Iron Rods, Face Plate, Base Bench Wise,savueesing Cylinder, Lifting Bcm Roll, Tamping Arm, And Other Items Coming Under Ms Scrap On As Is Where Is Condition Available Under The Custody Of Cdms 08 Ward. Note: Pick And Choose Of The Material Are Not Allowed. Loading To Be Started From One End And To Be Ended On Other End Only. (loc:bin No. 0139 At Scrap Yard

Description: Mixed Scrap : Actual Lot No. 03122502 0624. Pl No.98050047 (15) (hsn Code 72044900-gst18% On Fcm Basis) Scrap Of Cond. & Unserviceable Mixed Scrap Of Ms, Cs, Ci, Gi, Ss Contains Pipes End Body Pcs. Horizontal Levers Hand Brake Wheels Angle And Channel Pcs, Rod Pcs Stands Valves Levers Bolts And Nuts Rivets Washers Pins Foot Steps Cut Bits Side Barer Housings Pipe Pcs Straps Liners Sheets Pipe Pcs Pins Throwers Locks Races Collars Axle Box Covers, Air Brake Pipes, Guard Seats, Ms End Body Pcs, Ms Sheets, Ms Cut Bits, Ms Rod Pcs, Sab Parts, Gi Wire, Ms Ladders, Ms Channels, Door Hangers, Tool Box, Ms Meshes, Bp Fp Hose Pipes, Knuckles, Crushed Paint Drums, Grease Seals, Yoke Support Plates, Yoke Pins, Sheet Strips, Ms Pipes And Pcs, Rubber Pads, Chairs, Roof Sheets, Grease Drum, Auxiliary Reservoirs, Cone Bearing, Hoop Iron. Wedges Hyd. Hoses Fabricating Scrap And Other Misc Items Of Wagons Sorts & Sizes Full Or Broken With Or Without Attachments Location: Road No.3 (single Cut Permitted For Loading Purpose Only) (note: 1. If Any Ss/ Corten Steel & Non-ferrous Items Found During Loading / Delivery Shall Be Return To The Railways By The Purchaser 2. In Case Of Clubbed Lots, Purchaser Has To Clear The Lots In The Sequence As Mentioned In The Lot Description And No Deviation Is Accepted. 3. No Picking And Choosing Of Material Is Permitted While Taking Delivery )

Description: CATEGORY: Fabrication and supply of superior quality heavy duty 04 wheel mobile tray , Base and top frame of MS angle 40x40x5 mm , Towing hook frame of MS 40x40x 5 mm , Axle of MS draw hollow section 50mm dia 4 point 5mm thick , 1 point 5 MM thick wrinkle free HR sheet floor plate 3 point 65 x 1 point 2 m in which 1 point 2 M long MS angle iron 40x40x5 mm should be welded in center , 1 point 5 MM thick wrinkle free HR sheet right and left side plates 1 point 2 x 0 point 6 m in which 0 point 6 M long MS angle iron 40x40x5 mm should be welded in center , 1 point 5 MM thick wrinkle free HR sheet Up and Down side plates 1 point 2 x 0 point 6 m in which 0 point 6 M long MS angle iron 40x40x5 mm should be welded in center , Rubber moulded iron wheel 200mm dia as per sample , 30 MM dia MS draw towing hook , MS Jack for parking

Description: Cutting, Threading, Welding & Joint, Leth Fabrication, Turning Etc. Under Phed Rural Sub Div. Gangapur City At Jen Section Mahukalan, Distt.- Sawai Madhopur

Description: Cutting, Threading, Welding & Joint, Leth Fabrication, Turning Etc. Under Phed Sub Div. Bamanwas, Distt.- Sawai Madhopur

Description: Cutting, Threading, Welding & Joint, Leth Fabrication, Turning Etc. Under Phed Rural Sub Div. Gangapur City At Jen Section Udaikalan, Distt.- Sawai Madhopur

Description: Cutting, Threading, Welding & Joint, Leth Fabrication, Turning Etc. Under Phed Rural Sub Div. Gangapur City At Jen Section Wazeerpur, Distt.- Sawai Madhopur