Electrical Tenders

Details: Description Inclusion/deliverables: 1. 1 Unit 55” Led Monitor Tv With Wall Bracket 2. 1 Unit 32 Channel Dvr Recorder 3. 2 Units Cctv Hard Disk 4tb 4. 32 Units Ccctv Bullet/dome Camera 5. 3 Rolls Utp Cable Cat 6 Outdoor 6. 1 Set Psu Box Power Supply 40amp 7. 3 Sets Psu Box Power Supply 20amp 8. 1 Set Psu Box Power Supply 10amp 9. 32 Pieces Cctv White Junction Box 100x100x70mm 10. 5 Pieces Cctv White Junction Box 150x110x70mm 11. 32 Sets Cctv Video Balun 8mp 12. 32 Sets Dc Plug Balun Male & Female 13. Other Hardware And Electrical Supplies & Materials Scope Of Work: 1. Site Survey And Assessment: Conduct A Thorough Site Survey To Determine The Layout, Size, And Specific Security Needs Of The Premises. Identify High-risk Areas, Points Of Entry/exit, Blind Spots, And Areas Requiring Special Surveillance Attention. Evaluate Existing Infrastructure For Compatibility With Cctv Installation. 2. System Design And Layout: Develop A Comprehensive Cctv System Design Based On The Site Survey Findings. Determine Camera Placements, Angles, And Coverage Areas To Ensure Maximum Surveillance Effectiveness. Select Appropriate Camera Types (e.g., Dome Cameras, Bullet Cameras) Based On Specific Surveillance Requirements. Design Network Infrastructure For Seamless Camera Connectivity And Data Transmission. 3. Equipment Procurement: Procure High-quality Cctv Cameras, Recording Devices, Monitors, Cables, And Other Necessary Equipment From Reputable Suppliers. Ensure Compatibility And Compliance With Industry Standards And Regulations. Obtain Quotes And Compare Prices To Ensure Cost-effectiveness Without Compromising Quality. 4. Installation And Integration: Install Cctv Cameras At Designated Locations As Per The Approved System Design. Mount Cameras Securely And Adjust Angles For Optimal Coverage. Integrate Cctv Cameras With Recording Devices, Monitors, And Existing Security Systems (if Applicable). Configure Network Settings For Remote Access And Monitoring Capabilities. 5. Testing And Commissioning: Conduct Thorough Testing Of All Cctv Components To Ensure Proper Functionality. Verify Camera Angles, Image Quality, Motion Detection, And Recording Capabilities. Test Remote Access And Monitoring Features To Ensure Seamless Operation. Address Any Issues Or Discrepancies Identified During Testing. 6. Training: Provide Comprehensive Training Sessions For Designated Personnel On Cctv System Operation, Monitoring, And Basic Troubleshooting. Ensure Staff Members Are Proficient In Accessing And Using Cctv Footage Effectively. Conduct A Formal Handover Of The Cctv System To The Client, Ensuring All Deliverables Are Met And Expectations Are Fulfilled. Timeline: The Estimated Timeline For Completion Of The Project Is 3-5 Days, Subject To Adjustments Based On Site Conditions, Equipment Availability, And Client Feedback. Budget: The Proposed Budget For The Project Is P 270,000.00, Inclusive Of Tax, Equipment (supplies, Tools & Materials) Procurement, Installation, Training.

Details: Description: 1. Summary The Meteorological Service Of Canada (msc) Requires A Contractor To Perform Design And Installation Of A Freestanding Radome Tower, Along With Integration Of The New Satellite Antenna System. This Will Be Performed At The Agriculture And Agri-food Canada And Environment And Climate Change Canada Facility At 308 Brookfield Road, St. John’s Nl, A1e 0b2. The Self-supported Tower Must Be Designed By A Professional Engineer Licensed In Good Standing In The Province Of Newfoundland And Labrador To Incorporate The New Antenna System. To Determine The Tower Location, A Survey Of The Surrounding Terrain Must Be Conducted By The Contractor, At The 66% Design Review Presenting Geotechnical Consideration, Siting And Environmental Consideration. The Geotechnical Survey Must Be Completed To The Canadian Foundation Engineering Manual Standards (latest Edition), Along With Any Local And Provincial Codes/mandates. The Antenna Vendor Will Deliver The Antenna System With Electrical Certification To Csa 22.2 Standards. The Contractor Must Provide Power, Trenching And Conduit To A Mounting Platform For The Antenna Pedestal. This Installation Must Meet All Provincial And Federal Requirements And Be Inspected By Authorities Having Jurisdiction. The Tower Must Be Tall Enough To Have The Center Of The Antenna At 10m Above The Plane Of The Driveway. Once The Location Of The Tower Is Determined, The Exact Height Of The Tower (from Foundation To Base Of Antenna) Can Be Determined. The Tower Must Be Able To Support The Structural Loads Of The 2.4 M Dish Antenna Listed In Table 2 And The 4.3 M Radome Listed In Table 3 Of Appendix A. The Contractor Must Secure The Tower Access With Fences Or Any Locked Mechanism Appropriate For The Design And Location Where The Tower Will Be Installed. The Security Fence Must Be ~2.5 M Tall With Barbed Wire On Top And Fit A Radius That Is At Least 3 M Wider Than The Radome Were It Siting At Ground Level. The Contractor Must Install A Gravel Pedestrian Walkway Coming From The North-west Facing Door Of The Ops Building To The Access At The Base Of The Tower. The Contractor Must Perform And Complete The Work By May 30, 2025. 2. Security There Are No Security Requirements Associated With This Solicitation. 3. Integrity Provisions Bidders Must Provide A List Of Names, Or Other Related Information As Needed, Pursuant To Section 01 Integrity Provisions Of Standard Instructions 2003. 4. Trade Agreements The Requirement Is Subject To The Provisions Of The Canadian Free Trade Agreement (cfta). 5. Social Procurement Environment And Climate Change Canada Supports The Government Of Canada’s Social And Economic Objectives, Including Increasing The Participation Of Businesses From Under-represented Groups In Government Procurement Opportunities. As Such, Bidders Owned Or Led By Canadians From Under-represented Groups, Such As Women, Lgbtq2+ Persons, Persons With Disabilities And Persons From Visible Minorities Are Encouraged To Submit A Bid To This Opportunity. 6. Optional Site Visit There Is An Optional Site Visit Associated With This Requirement. Consult Si03 Optional Site Visit. 7. Debriefings Bidders May Request A Debriefing On The Results Of The Bid Solicitation Process. Bidders Should Make The Request To The Contracting Authority Within 15 Working Days From Receipt Of The Results Of The Bid Solicitation Process. The Debriefing May Be In Writing, By Telephone Or In Person.” 8. Official Languages Environment And Climate Change Canada Provides Procurement Services In Both Official Languages. Bidders May Submit A Bid In The Official Language Of Their Choice. 9. Additional Information For Additional Information, Interested Suppliers Must Contact The Contracting Officer Named In This Notice.

Details: Notice Of Intent To Sole Source exhibit Space At 2025 Ieee International Conference On Robotics & Automation announcement Type: Special Notice announcement Number: Nist-noi-25-730111 subject: Exhibit Space At 2025 Ieee International Conference On Robotics & Automation introduction this Is A Notice Of Intent, Not A Request For A Quotation. A Solicitation Document Will Not Be Issued And Quotations Will Not Be Requested. purpose the National Institute Of Standards And Technology (nist) Intends To Negotiate A Firm-fixed Priced Purchase Order On A Sole Source Basis With The Institute Of Electrical And Electronics Engineers, Inc. (ieee), Uei: Wv5sky8mtfu1, Located At 445 Hoes Lane, Piscataway, Nj 08854. The Purchase Order Will Be For Booth Rental And Associated Support In The Exhibit Hall At The 2025 Ieee International Conference On Robotics And Automation. authority this Acquisition Is Being Conducted Under The Authority Of Far Subpart 13.106(b)(1) Allowing The Contracting Officer (co) To Solicit From One Source. The North American Industry Classification System (naics) Code For This Acquisition Is 561920 – Convention And Trade Show Organizers With A Size Standard Of $20 Million. description the Contractor Shall Provide One 400 Square Foot Island Exhibit Booth For Nist Use At The 2025 Ieee International Conference On Robotics And Automation Taking Place In Atlanta, Georgia From May 19 – 23, 2025. Booth Rental Shall Come With Access To A Post-conference Delegate List, Eight Exhibitor Personnel Passes, Access To Wifi Internet In The Exhibit Hall, And Listing In The Conference Exhibit Director And Conference Mobile App. sole Source Determination the Sole Source Determination Is Based On The Following: the National Institute Of Standards And Technology (nist) Mission Is To Promote U.s. Innovation And Industrial Competitiveness By Advancing Measurement Science, Standards, And Technology In Ways That Enhance Economic Security And Improve Quality Of Life. In Support Of This Mission, Nist Regularly Hosts Exhibit Booths At Scientific Meetings And Tradeshows To Provide Information And For Recruitment Purposes. nist Will Be In Attendance At The 2025 Ieee International Conference On Robotics And Automation And Requires Exhibit Booth Space To Provide Information And For Recruitment Purposes. The Conference Only Allows Exhibit Rentals Directly Through Its Organizer, Ieee. Therefore, Ieee Is The Only Capable Source. information For Interested Parties interested Parties That Believe They Could Satisfy The Requirements Listed Above For Nist May Clearly And Unambiguously Identify Their Capability To Do So In Writing By Or Before The Response Date For This Notice. This Notice Of Intent Is Not A Solicitation. any Questions Regarding This Notice Must Be Submitted In Writing Via Email To Ms. Lauren Roller, Contract Specialist, At Lauren.roller@nist.gov. All Responses To This Notice Of Intent Must Be Submitted Via Email To Lauren.roller@nist.gov So That They Are Received No Later Than October 15, 2024 At 10:00 Am Eastern Time. each Response Should Include The Following Business Information: contractor Name, Address, point Of Contact Name, Phone Number, And Email Address contractor Duns contractor Business Classification (i.e., Small Business, 8(a), Woman Owned, Hubzone, Veteran Owned, Etc.) As Validated In System For Award Management (sam). All Offerors Must Register In The Sam Located At Http://www.sam.gov/portal/sam/#1 capability Statement

Details: Description Invitation To Bid The Manila International Airport Authority (miaa For Brevity), Now Invites Bids For The Procurement Project, Particularly Described As: Project Name / Title Proposed Construction Of Additional Comfort Rooms At Naia Terminal 1, 2, And 3 Contract Duration Two Hundred Twenty-four (224) Calendar Days Bidder Eligibility Must Have Experience In The General Building Construction Involving Civil And Architectural Works, Electrical Works And Mechanical Works. Source Of Funding And Year Cy 2024 Cob Approved Budget For The Contract (abc) Amount In Words Pesos: One Hundred Twenty-one Million Nine Hundred Twelve Thousand Five Hundred Ninety-five And 31/100 Only Amount In Figures Php121,912,595.31 In Philippine Currency Procurement Project/ Identification Number Responsibility Center Code No. 24-e23d-10604010-22 Source Of Funding And Year Cy 2024 Cob Particulars: Intends To Apply The Sum Of Php121,912,595.31 Corresponding To Each Lot/item Per 24-e23d-10604010-22 Or Each Lot/item Being The Abc To Payments Under The Contract For Each Lot/item. The Schedules Of Bac Activities Are As Follows: Activities Date And Time Venue 1. Issuance Of Bid Documents Prospective Bidders May Obtain Further Information From Bac Secretariat And Inspect The Bidding Documents. Cost Of Bidding Documents Php50,000.00 Only. January 03, 2025 To January 28, 2025 (8:00 Am-5:00 Pm) Bac Secretariat 4/f, Miaa Administration Building 2. Pre-bid Conference 14 January 2025 At 02:00 Pm Audio Visual Room, 4/f, Miaa Administration Building 3. Submission And Receipt Of Bids Must Be Duly Received By The Bac Secretariat. Late Bids Shall Not Be Accepted 28 January 2025 Not Later Than 12 Nn. Bac Secretariat 4/f, Miaa Administration Building 4. Bid Opening 28 January 2025 At 2:00 Pm Audio Visual Room, 4/f, Miaa Administration Building Bids Received In Excess Of The Abc Are Automatically Rejected At Bid Opening. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using A Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) No. 9184. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In The Instruction To Bidders (itb) Clause 14. The Miaa Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Irr Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. For Further Information, Please Refer To: Mr. Benjamin T. Manalili Iii Bids And Awards Committee Nos. 88771109 Loc. 3736,3838 And 3010 E-mail: Bac@miaa.gov.ph / Miaa.bac.secretariat@gmail.com Date Of Issue: January 03, 2025 …. --------------------------------------------------------------------------------------- Mgen. Manuel V. Sequitin, Pa (ret) Cese Chairperson, Miaa Bids And Awards Committee

Details: Presolicitation Notice naics Code: 236220 – Commercial And Institutional Building Construction the 167th Airlift Wing Intends To Issue An Invitation For Bids (ifb) To Award A Single Firm-fixed-price (ffp) contract For Services, Non-personal, To Provide All Plant, Labor, Transportation, Materials, Tools, Equipment, appliances, And Supervision Necessary For The Renovation Of Bldg 309 For Operations And Training In martinsburg, Wv. This Project Will Include: Renovation (roughly 29,109 Sq Ft) Of An Existing Two-story Facility to Relocate Headquarters Functions. Work Includes Interior Wall Relocation, And Necessary Relocation/ upgrade Of Electrical, Hvac, Mechanical, And Fire Protection Systems. Secure Briefing Spaces will Be Required In The Command Post Area, Which Shall Comply With Icd 705 Requirements. The Following options Are Included In This Project: (1) Window Shades And Blinds, (2) Wire Mesh Partitions, (3) communication Wiring, (4) Command Post Bathroom, (5) Financial Suite, And (6) Flight Service. the Contract Duration Is 550 Days After The Notice To Proceed (ntp). This Project Is Set-aside 100% For small Businesses. The North American Industry Classification (naics) Code Is 236220 With A Size standard Of $45,000,000.00. The Magnitude Of Construction Is Between $1,000,000 And $5,000,000. your Attention Is Directed To Far Clause 52.219-14(e)(3), Limitations On Subcontracting, Which states “by Submission Of An Offer And Execution Of A Contract, The Offeror/contractor Agrees In performance Of The Contract In The Case Of A Contract For General Construction, It Will Not Pay More Than 85 percent Of The Amount Paid By The Government For Contract Performance, Excluding The Cost Of Materials, to Subcontractors That Are Not Similarly Situated Entities. Any Work That A Similarly Situated Entity Further subcontracts Will Count Toward The 85 Percent Subcontract Amount That Cannot Be Exceeded”. the Tentative Date For Issuing The Solicitation Is On-or-about 15 April 2025. The Tentative Date For The Prebid conference Is On-or-about 4 May 2025, 9:00 Am Local Time, Location Will Be In The Solicitation. interested Contractors Are Encouraged To Attend And Shall Follow Conference Registration And Base Access requirements Shown In The Solicitation. A Site Visit Will Follow The Pre-bid Conference. All Questions For The pre-bid Conference Must Be Submitted By 13 May 2025 Via Email To Ryan.belfield@us.af.mil And christopher.broschart@us.af.mil. the Bid Opening Date Is Scheduled For On-or-about 3 June 2025. Actual Dates And Times Will Be Identified in The Solicitation. Interested Offerors Must Be Registered In The System For Award Management (sam). To register Go To Www.sam.gov. Instructions For Registering Are On The Web Page (there Is No Fee For registration). the Solicitation And Associated Information And The Plans And Specifications Will Be Available Only From The contract Opportunities Page At Sam.gov. disclaimer: The Official Plans And Specifications Will Be Located On The Official Government Webpage and The Government Is Not Liable For Information Furnished By Any Other Source. Amendments, If/when issued Will Be Posted To Contract Opportunities For Electronic Downloading. This Will Normally Be The Only method Of Distributing Amendments Prior To Closing; Therefore, It Is The Offeror’s Responsibility To Check The website Periodically For Any Amendments To The Solicitation. Websites Are Occasionally Inaccessible, Due To various Reasons. The Government Is Not Responsible For Any Loss Of Internet Connectivity Or For An Offeror’s inability To Access The Documents Posted On The Referenced Web Pages. The Government Will Not Issue paper Copies.

Details: Description No Item Description Quantity Unit 1 Ball Pen (black Ink) 3 Box 2 Floor Wax (450grams); Colorless 5 Can Ink 003: 3 Black 2 Bottle Ink For Brother Dcp-t420w: 4 Black 2 Bottle 5 Yellow 4 Bottle 6 Magenta 4 Bottle 7 Cyan 5 Bottle 8 Sticker Paper, A4, Inkjet, Printable, Glossy 10's 5 Pack 9 Correction Tape 10 Piece 10 Paper Tape 1" 10 Piece 11 Paper Tape 2" 10 Piece 12 Transparent/scotch Tape 1" 10 Piece 13 Clear Pvc Cover 100's, A4 1 Pack 14 Expanded Folder (long) 100 Piece 15 Folder, White (long) 100 Piece 16 Bond Paper 70gsm, A4 Size 60 Ream 17 Book Paper 80gsm, A4 Size 25 Ream 18 Book Paper 80gsm, Long Size 20 Ream 19 Alcohol 200-250ml 20 Bottle 20 Double-sided Tape 10 Piece 21 Transparent/scotch Tape 2" 10 Piece 22 Gelpen/sign Pen 0.5 (black) 12 Piece 23 Gelpen/sign Pen 0.5 (blue) 12 Piece 24 Electrical Tape 5 Piece 25 Staple Wire No. 35 10 Box 26 Tabbing Sticker (please Sign) 10 Pack 27 Folder, White (a4) 100 Piece 28 Whiteboard Marker, Blue 24 Piece 29 Whiteboard Marker, Black 36 Piece 30 Index Card 5*8 Inch, 100's 2 Pack 31 Pencil #2 12 Piece 32 Kiwi Envelope, Plastic Long Envelope 50 Piece 33 Paper Clip 33mm, Vinyl-coated, 100's 10 Box 34 Thumb Tacks 10 Box 35 Manila Paper 200 Piece 36 Scissor 10 Piece 37 Glue (medium) 10 Piece 38 Car Freshener 5 Piece 39 Multipurpose Cleaner 900ml 10 Bottle 40 Albatross Deodorizer 100g 15 Piece 41 Air Freshener (pink/green) 320ml 15 Bottle 42 Detergent Powder 500g 20 Pack 43 Dishwashing Liquid, 500ml 20 Bottle 44 Muriatic Acid 10 Bottle 45 Bleach 1l 15 Bottle 46 Disinfectant Spray, 170g/227ml 15 Bottle 47 Toilet Tissue 1 Box 48 Kitchen Tissue 10 Roll 49 Sponge 20 Piece 50 Hand Bar Soap 90g 15 Bar 51 Detergent Bar 25 Bar 52 Glass Cleaner 500ml 5 Bottle 53 Glass Wiper 5 Piece 54 Toilet Cleaning Brush With Holder Set 10 Set 55 Hand/laundry Brush (plastic/wood) 10 Piece 56 Dipper 20 Piece Nothing Follows

Details: Description Republic Of The Philippines Municipality Of Paniqui Province Of Tarlac Solicitation No.: I-2025-004 Name Of The Project : Construction Of Two Storey Multi-purpose Building Location Of The Project : Pob. Sur, Paniqui, Tarlac Invitation To Apply For Eligibility And To Bid The Municipality Of Paniqui Through Its Bids And Awards Committee (bac), Invites Contractors Registered With And Classified By The Philippine Contractors Accreditation Board (pcab) To Apply For Eligibility And If Found Eligible, To Bid For The Hereunder Project: Name Of Contract : Construction Of Two Storey Multi-purpose Building Location : Pob. Sur, Paniqui, Tarlac, Paniqui, Tarlac Brief Description : General Requirements, Earthworks, Earthfill, Foundation (cf,tb), R.c. Column (grnd To 2nd Flr), , Concrete Slab (on Floor), Plastered Chb Wall (ground), Second Floor Beam, Concrete Slab (2nd Floor), R.c. Column (2nd Flr To Rb) , Plastered Chb Wall (2nd Floor), Roof Beam, Roof & Roof Framing, Ceiling (ground And 2nd Floor), Concrete Stair, Plumbing & Septic Tank, Formworks, Doors And Windows, Electrical, Painting, Tiles, Site Prep & Site Devt, Mobilization,/demobilization, Project Billboard, Occupational Health And Safety Program Approved Budget For The Contract : P 3,800,000.00 Source Of Fund : General Fund Contract Duration : 210 Days (a) Prospective Bidders Should Possess A Valid Pcab License Applicable To The Contract, Have Completed A Similar Contract With A Value Of At Least 50% Of The Abc, And Have Key Personnel And Equipment (listed In The Eligibility Forms) Available For The Prosecution Of The Contract. The Bac Will Use Non-discretionary “pass/fail” Criteria In The Eligibility Check/screening As Well As The Preliminary Examination Of Bids. The Bac Will Conduct Post-qualification Of The Lowest Calculated Bid. (b) The Complete Schedule Of Activities Is Listed As Follows: Activities Schedule 1. Issuance Of Bid Documents January 10, 2025 To February 5, 2025, 8am To 5pm @ Bac Office, Lgu-paniqui, Tarlac , 2. Pre-bid Conference January 24, 2025, 11:00am @ Bac Office 2. Submission, Receipt And Opening Of Bids February 5, 2025, 11:00am @ Bac Office, Lgu-paniqui, Tarlac For Single-stage Bidding: (c) Bid Documents Is Available From January 10, 2025 To February 5, 2025, 8am To 5pm At Bac Office, Lgu-paniqui, Tarlac Only To Prospective Bidders Upon Payment Of A Non-refundable Amount Of Five Thousand Pesos (p 5,000.00) To The Municipality Of Paniqui Cashier. (d) The Municipality Of Paniqui Assumes No Responsibility Whatsoever To Compensate Or Indemnify Bidders For Any Expenses Incurred In The Preparation Of The Bid. (e) For Further Information, Interested Bidders May Access The Bidding Documents Thru Www.paniquitarlac.gov.ph Or Inquire From The Bac Secretariat And Look For Mr. Gaylord P. De Guzman From 8:00am -5:00pm, Monday To Friday At Lgu-paniqui, Tarlac With Tel. No. (045) 931-0303. Date Of Publication : January 10, 2025 To February 5, 2025 Type Of Publication : Bulletin, Philgeps & Website Approved By: Eugenio B. Galanga, Rsw Bac Chairman

Details: Description Inclusion/deliverables: 1. 1 Unit 55” Led Monitor Tv With Wall Bracket 2. 1 Unit 32 Channel Dvr Recorder 3. 2 Units Cctv Hard Disk 4tb 4. 32 Units Ccctv Bullet/dome Camera 5. 3 Rolls Utp Cable Cat 6 Outdoor 6. 1 Set Psu Box Power Supply 40amp 7. 3 Sets Psu Box Power Supply 20amp 8. 1 Set Psu Box Power Supply 10amp 9. 32 Pieces Cctv White Junction Box 100x100x70mm 10. 5 Pieces Cctv White Junction Box 150x110x70mm 11. 32 Sets Cctv Video Balun 8mp 12. 32 Sets Dc Plug Balun Male & Female 13. Other Hardware And Electrical Supplies & Materials Scope Of Work: 1. Site Survey And Assessment: Conduct A Thorough Site Survey To Determine The Layout, Size, And Specific Security Needs Of The Premises. Identify High-risk Areas, Points Of Entry/exit, Blind Spots, And Areas Requiring Special Surveillance Attention. Evaluate Existing Infrastructure For Compatibility With Cctv Installation. 2. System Design And Layout: Develop A Comprehensive Cctv System Design Based On The Site Survey Findings. Determine Camera Placements, Angles, And Coverage Areas To Ensure Maximum Surveillance Effectiveness. Select Appropriate Camera Types (e.g., Dome Cameras, Bullet Cameras) Based On Specific Surveillance Requirements. Design Network Infrastructure For Seamless Camera Connectivity And Data Transmission. 3. Equipment Procurement: Procure High-quality Cctv Cameras, Recording Devices, Monitors, Cables, And Other Necessary Equipment From Reputable Suppliers. Ensure Compatibility And Compliance With Industry Standards And Regulations. Obtain Quotes And Compare Prices To Ensure Cost-effectiveness Without Compromising Quality. 4. Installation And Integration: Install Cctv Cameras At Designated Locations As Per The Approved System Design. Mount Cameras Securely And Adjust Angles For Optimal Coverage. Integrate Cctv Cameras With Recording Devices, Monitors, And Existing Security Systems (if Applicable). Configure Network Settings For Remote Access And Monitoring Capabilities. 5. Testing And Commissioning: Conduct Thorough Testing Of All Cctv Components To Ensure Proper Functionality. Verify Camera Angles, Image Quality, Motion Detection, And Recording Capabilities. Test Remote Access And Monitoring Features To Ensure Seamless Operation. Address Any Issues Or Discrepancies Identified During Testing. 6. Training: Provide Comprehensive Training Sessions For Designated Personnel On Cctv System Operation, Monitoring, And Basic Troubleshooting. Ensure Staff Members Are Proficient In Accessing And Using Cctv Footage Effectively. Conduct A Formal Handover Of The Cctv System To The Client, Ensuring All Deliverables Are Met And Expectations Are Fulfilled. Timeline: The Estimated Timeline For Completion Of The Project Is 3-5 Days, Subject To Adjustments Based On Site Conditions, Equipment Availability, And Client Feedback. Budget: The Proposed Budget For The Project Is P 270,000.00, Inclusive Of Tax, Equipment (supplies, Tools & Materials) Procurement, Installation, Training.

Details: Description Republic Of The Philippines Province Of South Cotabato Bids And Awards Committee Salada Street, Poblaciontupi, South Cotabato Tel. Fax No.: (083) 226-1045 Invitation To Bid For The Supply & Delivery Of Materials For The Construction Of 1 Cl Classroom At Polonuling National High School, Polonuling, Tupi, South Cotabato 1. The Municipality Of Tupi Through The Trust Fund Intends To Apply The Sum Of Php 647,636.00 Being The Approved Budget For The Contract (abc) To Payments Under The Contract For Supply And Delivery Of Materials For The Construction Of 1 Cl Classroom At Polonuling National High School, Brgy. Polonuling, Tupi, South Cotabato/itb 048-2023. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. 2. The Municipality Of Tupi Now Invites Bids For The Construction Materials. Delivery Of Goods Is Required Seven (7) Days After The Signing Of The Contract. Bidders Should Have Completed, Within Three (3) Years From The Date Of Submission And Receipt Of Bids, A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii. Instructions To Bidders. 3. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using A Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) 9184, Otherwise Known As The “government Procurement Reform Act”. Bidding Is Restricted To Filipino Citizens/sole Proprietorships, Partnerships, Or Organizations With At Least Sixty Percent (60%) Interest Or Outstanding Capital Stock Belonging To Citizens Of The Philippines, And To Citizens Or Organizations Of A Country The Laws Or Regulations Of Which Grant Similar Rights Or Privileges To Filipino Citizens, Pursuant To Ra 5183. 4. Interested Bidders May Obtain Further Information From Municipality Of Tupi Bac-secretariat, And Inspect The Bidding Documents At The Address Given Below During 8:00am To 5:00 Pm, Mondays –fridays. 5. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders On May 12, 2023 To May 22, 2023 From The Bids And Awards Committee-secretariat, Municipality Of Tupi, South Cotabato And Upon Payment Of The Applicable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb, In The Amount Of 1,000.00 6. Bids Must Be Duly Received By The Bac Secretariat At The Address Below On Or Before May 23, 2023, 12:00 Noon. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 18. Bid Opening Shall Be On May 23, 2023, 2:00 P.m At 2nd Floor Bac Conference Room, Municipal Hall, Tupi, South Cotabato. Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend At The Address Below. Late Bids Shall Not Be Accepted. 7. The Municipality Of Tupi Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Section 41 Of Ra 9184 And Its Irr, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 8. For Further Information, Please Refer To: Bac Secretariat Tupi Municipal Hall Poblacion, Tupi, South Cotabato Tel No. 083-226-1045x Email: Tupi.bacsecretariat@gmail.com Republic Of The Philippines Province Of South Cotabato Municipality Of Tupi Bids And Awards Committee Invitation To Bid Date: May 9, 2023 Itb No: 048-2023 Please Submit Your Sealed Bids For The Supply And Delivery Of Materials For The Construction Of 1 Cl Classroom At Polonuling National High School, Polonuling, Tupi, South Cotabato Listed Below At The Bac Secretariat Office On Or Before The Opening Of Bids On May 23, 2023 At 2:00 P.m. Note: 1. Abc= Php 647,636.00 2. All Entries Must Be Typewritten/printed Ligibly. Avoid Erasures. 3. Delivery Period Within __ Calendar Days. 4. Warranty Shall Be For A Period Of One (1) Year From The Date Of Acceptance By The Procuring Entity. 5. Bids Shall Be Accompanied By Bond In The Form Of Cash, Manager's Check Equal To 2% Or Surety Bond Equal To 5% Of The Approved Budget For The Contract Or A Bid Securing Declaration. 6. Bidders Shall Submit Original Brochures Showing Certifications Of Product Being Offered. Item No. Item & Description Qty Unit Unit Price Total Amount 1. Cement 330 Bags 2. Washed Sand 30 Cu.m 3. 3/4 Gravel 18 Cu.m 4. 16mm Diam. Rsb 58 Lnght 5. 12mm Diam. Rsb 96 Lnght 6. 10mm Diam Rsb 228 Lngth 7. # 16 Tie Wire 64 Kgs 8. 10cmx20x40cm Chb 2000 Pcs 9. Cutting Dist 50 Pcs 10. Diamond Cutting Disk 4 Pcs 11. 150pcs, 2x2x12 Coco Lumber 300 Bd.ft 12. 150pcs, 2x3x12 Coco Lumber 900 Bd.ft 13. 4x8x10mm Thk. Ordinary Plyboard 10 Shts 14. 4" Cw Nails 25 Kls 15. 3" Cw Nails 25 Kls 16. 2 1/2" Cw Nails 25 Kls 17. 1 1/2" Cw Nails 25 Kls 18. 4" Concrete Nails 5 Kgs 19. 2"x2"x3/16 Angle Bar 2 Length 20. 2"x4"x1.20mm Thick C-purlins 49 Length 21. 2"x3"x1.20mm Thick C-purlins 17 Length 22. Ga 24x8' Corrugated G.i Sheet 44 Ln.m 23. Ga 24x12' Corrugated G.i Sheet 10 Ln.m 24. Roofgard (foam Green Color) 4 Pail 25. 2" Teckscrew 400 Pcs 26. 0.40mm Thick Pre-fab. Ridge Roll 5 Pcs 27. 0.40mm Thick Pre-fab. Gutter 10 Pcs 28. 0.40mm Thick Pre-fab. Flashing 11 Pcs 29. 1/8x7/8 Rivets @ 250pcs/box 25 Box 30. 1611 Welding Rod @ 5kls/box 3 Box 31. Red Oxide 1 Pail 32. Paint Thinner 10 Gal. 33. 4" Paint Brush 6 Pcs 34. Water Closet Set Heavy Duty Veronica White Package Model (including Soap & Tissue Holder ) With Complete Accessories 2 Set 35. 4" Dia.x 3m S1000 Pvc Pipe 3 Pcs. 36. 4" Dia. S1000 Pvc Wye 3 Pcs. 37. 4" Dia. S1000 Pvc Elbow 90˚ 4 Pcs. 38. 4" Dia. S1000 Pvc U-trap 2 Pcs. 39. 4" S1000 Pvc Clean Out W/ Plug 4 Pc. 40. 3" Dia. S1000 Pvc Pipe 6 Lengths 41. 3" Dia. S1000 Pvc Elbow 90˚ 3 Pcs. 42. 3" Dia. S1000 Pvc Wye 3 Lengths 43. 3" Dia. S1000 Pvc U-trap 2 Pcs. 44. 3" Dia. S1000 Pvc Tee 2 Pcs. 45. 4" Dia.x 2" S1000 Pvc Tee Reducer 2 Pcs 46. 3" Dia.x 2" S1000 Pvc Tee Reducer 2 Pcs 47. 2" Dia. S1000 Pvc Tee 2 Pcs 48. 4"x4" Stainless Floor Drain 2 Lengths 49. 1/2" Dia. Gooseneck Faucet (hd) 2 Pcs. 50. 1/2" Dia. Upvc Pipe 4 Lengths 51. 1/2" Dia. Upvc Tee 2 Pc. 52. 1/2" Dia. Upvc Elbow 90˚ 6 Pcs. 53. 1/2" Dia. Upvc Coupling 8 Pcs. 54. 1/2" Dia. Upvc Female Threaded Adaptor 4 Pcs. 55. 1/2" Dia. Upvc Cup Plug 2 Pcs. 56. Cement Solvent 5 Can 57. 4" X 4" Junction Box 8 Set 58. 32mm Ø Electrical Pvc Conduit Pipe 2 Lengths 59. 20mm Ø Electrical Pvc Conduit Pipe 5 Lengths 60. 20mm Ø Electrical Pvc Elbow 2 Pcs 61. Flexible Hose # 1/2 1 Rolls 62. 30mm2 Thhn Copper Wire 3 M 63. #12 Thhn Copper Wire 1 Rolls 64. #14 Thhn Copper Wire 1 Rolls 65. 1 Gang Switch With Luminous Light On Switch 2 Sets 66. 3 Gang Switch With Luminous Light On Switch 2 Sets 67. 3 Gang Convenience Outlet (flush Type) 3 Sets 68. 6" Square Ultra Thin Downlight 20w Wide Beam Angle 10 Sets 69. 2- 18w Led Parabolic Louver Lights (day Light) 2 Sets 70. Entrance Cap 3/4 1 Pcs 71. Straight Connector 1 Pc 72. 6 Branches Panel Board 1 Set 73. Circuit Breaker 15 Amps (plug-in Type) 2 Pc 74. Circuit Breaker 20 Amps (plug-in Type) 1 Pcs 75. Circuit Breaker 60 Amps (plug-in Type) 1 Pcs 76. Electrical Tape (big) 5 Pcs 77. 0.90mx2.1m Flash Door W/ Jamb (pre Painted, Palmyra Green) 2 Set 78. 4"x4" Hinges 8 Set 79. Kwikset Door Knob 4 Set 80. 0.6mx6' Pvc Door W/ Complete Accessories 2 Set 81. 1.30mx4.90m White Board With Frame (for Classroom Used)(including Installation On Site) 1 Set 82. 0.60mx1.20m Jalousie Window W/ Aluminum Frame 11 Set 83. 0.60mx0.60m Awning Type Window 2 Set 84. 12mm Diameter Squareplain Bar 20 Length 85. Metal Primer (color Black) 1 Gal. 86. #6 Tox Screw 30 Pcs 87. #6 Screw 30 Pcs 88. 30cmx60cm Glazed Tiles Wall Tiles 95 Pcs 89. 30cmx60cm Unglazed Tiles Floor Tiles 25 Pcs 90. Tile Grout(white Color) 43 Kg 91. Tile Adhesive (25kg/bag) 10 Bags 92. Aluminum Tile Trim Corner 8 Length 93. Concrete Neutralizer 1 Pail 94. Acretex Primer 4 Pail 95. Acretex Top Coat (beige, Light Shade) 4 Pail 96. Acretex Top Coat (beige, Very Light Shade) 2 Pail 97. # 120 Sand Paper 30 Pcs 98. # 100 Sand Paper 30 Pcs 99. 10" Paint Roller With Pan 6 Set 100. # 2 Paint Brush 4 Pcs 101. # 4 Paint Brush 4 Pcs 102. White Flat Enamel Paint 2 Pail 103. Quick Fry Enamil Semi Gloss (foam Green Color) 2 Gal. 104. Skimcaot 8 Bags 105. Polituff (body Filler) 8 Gal. 106. 6" Putty Knife 6 Pcs 107. 19mm X 50mm X .40mm Thk X 5m Double Furring Ceiling Joist 70 Length 108. 12mm X 38mm X .80mm Thk X 5m Carrying Channel 80 Length 109. 25mm X 25mm X 3.00mm X 2.40m Wall Angle 36 Length 110. 5mm Thk Cement Board 45 Sheet 111. Wooden Airvent With Fine Mosquito Screen Fillings (.30m X 1.20m) 4 Pcs 112. W Clip For Metal Furring 368 Pcs 113. Exhaust Fan 2 Set 114. Earthfill 30 Cu.m 115. #30 Drill Bit 10 Pcs ******************************************** Total Amount Of Bid In Figures: Php _____________________________________________________ Total Amount Of Bid In Words:_________________________________________________________ For: Supply And Delivery Of Materials For The Construction Of 1 Cl Classroom At Polonuling National High School, Polonuling, Tupi, South Cotabato Place Of Delivery: Lgu-tupi, South Cotabato/mpdo Delivery Period : _____________________ Warranty : _____________________ Price Validity : _____________________ After Having Carefully Read And Accepted Your General Conditions, I/we Quote You On The Item At Prices Noted Above. Printed Name/signature Tel.no./cellphone No. E-mail Address Sgd Arnen L. Kasan Mgdh-mbo Bac Chairperson

Details: Description Republic Of The Philippines Department Of Public Works And Highways Marinduque District Engineering Office Boac, Marinduque, Mimaropa (region Iv-b) Invitation To Bid For Basic Infrastructure Program (bip), Multi-purpose Buildings/ Facilities To Support Social Services, Completion Of Multi-purpose Building (phase 2), Barangay Ino, Mogpog, Marinduque 1. The Dpwh-marinduque District Engineering Office, Through The Gaa Fy 2025 Intends To Apply The Sum Of Php 3,954,800.00 Being The Approved Budget For The Contract (abc) To Payments Under The Contract For 25ea0050 - Basic Infrastructure Program (bip), Multi-purpose Buildings/ Facilities To Support Social Services, Completion Of Multi-purpose Building (phase 2), Barangay Ino, Mogpog, Marinduque. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. 2. The Dpwh-marinduque District Engineering Office Through Its Bids And Awards Committee Now Invites Bids For The Hereunder Works: Name Of Contract : Basic Infrastructure Program (bip), Multi-purpose Buildings/ Facilities To Support Social Services, Completion Of Multi-purpose Building (phase 2), Barangay Ino, Mogpog, Marinduque Contract Id No. : 25ea0050 Locations : Brgy. Ino, Mogpog, Marinduque Scope Of Works : Construction Of 30 Columns And Footings; Roof And Roof Framing For Canopy; Bleachers; Septic Tank; Angular Fence; Comfort Rooms. It Also Includes Stainless Steel Railings; Complete Sets Of Doors And Windows; Painting Works; Formworks; 100mm And 150mm Chb Walls; Cement Plaster Finish; Floor Finish; Tileworks; Ceiling Works; Plumbing Works; And Electrical Works. Including Zoning Fee/locational Clearance, Professional Fee, Filing Fee, Occupancy Permit And Electrical Fee. (see Plans For Details) Approved Budget For The Contract : Php 3,954,800.00 Contract Duration : 110 Calendar Days Bidders Should Have Completed A Contract Similar To The Project. The Description Of An Eligible Bidders Is Contained In The Bidding Documents, Particularly, In Section Ii (instruction To Bidders). 3. Prospective Bidders Should Be (1) Registered With And Classified By The Philippine Contractors Accreditation Board (pcab) With Pcab License Category Of At Least C&d For Small B. Contractors/applicants Who Wish To Participate In This Bidding Are Encouraged To Enroll In The Dpwh Civil Works Application (cwa) At The Dpwh Procurement Service (prs), 5th Floor, Dpwh Bldg., Bonifacio Drive, Port Area, Manila, While Those Already Enrolled Shall Keep Their Records Current And Updated. The Contractor’s Eligibility To Bid On The Project Will Be Determined Using The Dpwh Contractor Profile Eligibility Process (cpep) And Subject To Further Post-qualification. Information On Registration Can Be Obtained From Theprs During Working Weekdays From 7:00 Am To 4:00 Pm Or At The Dpwh Website Www.dpwh.gov.ph. 4. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using Non- Discretionary Pass/fail Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act 9184 (ra 9184). 5. Interested Bidders May Obtain Further Information From The Dpwh-marinduque District Engineering Office And Inspect The Bidding Documents At Dpwh Marinduque Deo, Boac, Marinduque During Weekdays From 8:00 Am To 5:00 Pm. 6. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders On January 07-28, 2025 From The Address Below And Upon Payment Of The Applicable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb, In The Amount Of Php 5,000.00. 7. The Bidding Documents May Also Be Downloaded Free Of Charge From The Website Of The Philippine Government Electronic Procurement System (philgeps), And The Website Of The Procuring Entity, Provided That Bidders Shall Pay The Applicable Fee For The Bidding Documents Not Later Than The Submission Of Their Bids. 8. The Dpwh-marinduque District Engineering Office Will Hold A Pre-bid Conference On January 15, 2025, 9:00 A.m. At The Dpwh Marinduque Deo, Boac, Marinduque And Through Videoconferencing/webcasting Via Microsoft Teams, Which Shall Be Open To Prospective Bidders Via This Link Https://teams.microsoft.com/l/meetup-join/19%3ameeting_mdk0ywu2ztgty2i3ys00n2u5ltgxymitnzvjnja3mwe4y2fk%40thread.v2/0?context=%7b%22tid%22%3a%22b9e41a5f-4398-4578-89cf-6d3cdb824dcb%22%2c%22oid%22%3a%2267f51522-68c8-45e4-b629-a2cd72ac069a%22%7d. 9. Bid Submission Maybe Done Manually Or Electronically/online. However, Bidders Should Only Select One Mode Of Submission, Either Manual Or Electronic. Similar To Manual Submission, The Guidelines For The Preparation And Submission Of An Electronic Bid Are Contained In Bds Itb Clause 7. 10. Bids Must Be Duly Received By The Bac Secretariat At The Address Below For Manual Submission Or At Electronicbids_marinduque@dpwh.gov.ph For Electronic Submission On Or Before January 28, 2025, 10:00 Am. Late Bids Shall Not Be Accepted. 11. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 15. 12. Bid Opening Shall Be On January 28, 2025, 10:00 Am, Immediately After The Deadline For The Submission Of Bid At Dpwh Marinduque Deo, Boac, Marinduque And Through Microsoft Teams With The Link Indicated In The Bds Itb Clause 17.7. Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend At The Address Below. 13. The Dpwh-marinduque District Engineering Office Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Section 41 Of Ra 9184 And Its Irr, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 14. For Further Information, Please Refer To: Fernan S. Diaz Chief, Planning And Design Section Bac Chairperson Boac, Marinduque (042) 332-0806 Diaz.fernan@dpwh.gov.ph Julito M. Maglacas Engineer Iii Head, Bac Secretariat Boac, Marinduque (042) 332-1086 0915-738-6644 Maglacas.julito@dpwh.gov.ph Approved By: Fernan S. Diaz Bac Chairperson Date: January 07, 2025