Chair Tenders

Details: Description S P E C I F I C A T I O N S B.5 Project Billboard The Contractor Shall Install One (1) Billboard Measuring 8 Ft. X 8 Ft. Tarpaulin, In Front Of The Project Site. Project Billboard Shall Be Installed For Government Information Projects To Inform The Public Of The Implementation Of The Project And To Advise The Road Users Of The On-going Construction. Upon Completion Of The Work, All Signs Installed Shall Be Removed From The Site. 102(1) Roadway Excavation Removal Of Unsuitable Material Where The Plans Show The Top Portion Of The Roadbed To Be Selected Topping, All Unsuitable Materials Shall Be Excavated To The Depth Necessary For Replacement Of The Selected Topping To The Required Compacted Thickness. Where Excavation To The Finished Graded Section Results In A Subgrade Or Slopes Of Unsuitable Soil, The Engineer May Require The Contractor To Remove The Unsuitable Material And Backfill To The Finished Graded Section With Approved Material. The Contractor Shall Conduct His Operations In Such A Way That The Engineer Can Take The Necessary Cross-sectional Measurements Before The Backfill Is Placed. The Excavation Of Muck Shall Be Handled In A Manner That Will Not Permit The Entrapment Of Muck Within The Backfill. The Material Used For Backfilling Up To The Ground Line Or Water Level, Whichever Is Higher, Shall Be Rock Or Other Suitable Granular Material Selected From The Roadway Excavation, If Available. If Not Available, Suitable Material Shall Be Obtained From Other Approved Sources. Unsuitable Material Removed Shall Be Disposed Off In Designated Areas Shown On The Plans Or Approved By The Engineer. Item 201 – Aggregate Base Course 201.1 Description This Item Shall Consist Of Furnishing, Placing And Compacting An Aggregate Base Course On A Prepared Sub-grade/sub-base In Accordance With This Specification And The Lines, Grades, Thickness And Typical Cross-sections Shown On The Plans, Or As Established By The Lgu Project Engineer. 201.2 Material Requirements Aggregate For Base Course Shall Consist Of Hard, Durable Particles Or Fragments Of Crushed Stone, Crushed Slag Or Crushed Or Natural Gravel And Filler Of Natural Or Crushed Sand Or Other Finely Divided Mineral Matter. The Composite Material Shall Be Free From Vegetable Matter And Lumps Or Balls Of Clay, And Shall Be Of Such Nature That It Can Be Compacted Readily To Form A Firm, Stable Base. In Some Areas Where The Conventional Base Course Materials Are Scarce Or Non-available, The Use Of 40% Weathered Limestone Blended With 60% Crushed Stones Or Gravel Shall Be Allowed, Provided That The Blended Materials Meet The Requirements Of This Item. The Base Course Material Shall Conform To Table 201.1, Whichever Is Called For In The Bill Of Quantities Table 201.1 – Grading Requirements Sieve Designation Mass Percent Passing Standard, Mm Alternate Us Standard Grading A Grading B 50 2” 100 37.5 1-1/2” - 100 25.0 1” 60 – 85 - 19.0 ¾” - 60 – 85 12.5 ½” 35 – 65 - 4.75 No. 4 20 – 50 30 – 55 0.425 No. 40 5 – 20 8 – 25 0.075 No. 200 0 – 12 2 – 14 The Fraction Passing The 0.075 Mm (no. 200) Sieve Shall Not Be Greater Than 0.66 (two Thirds) Of The Fraction Passing The 0.425 Mm (no. 40) Sieve. The Fraction Passing The 0.425 Mm (no. 40) Sieve Shall Have A Liquid Limit Not Greater Than 25 And Plasticity Index Not Greater Than 6 As Determined By Aashto T 89 And T 90, Respectively. The Coarse Portion, Retained On A 2.00 Mm (no. 10) Sieve Shall Have A Mass Percent Of Wear Not Exceeding 50 By The Los Angeles Abrasion Test Determined By Aashto T 96. The Material Passing The 19 Mm (3/4 Inch) Sieve Shall Have A Soaked Cbr Value Of Not Less Than 80% As Determined By Aashto T 193. The Cbr Value Shall Be Obtained At The Maximum Dry Density (mdd) As Determined By Aashto T 180, Method D. If Filler, In Addition To That Naturally Present, Is Necessary For Meeting The Grading Requirements Or For Satisfactory Bonding, It Shall Be Uniformly Blended With The Base Course Material On The Road Or In A Pug Mill Unless Otherwise Specified Or Approved. Filler Shall Be Taken From Sources Approved By The Lgu Project Engineer, Shall Be Free From Hard Lumps And Shall Not Contain More Than 15 Percent Of Material Retained On The 4.75 Mm (no. 4) Sieve. 201.3 Construction Requirements 201.3.1 Preparation Of Existing Surface The Existing Surface Shall Be Graded And Finished As Provided Under Item 105, Sub-grade Preparation, Before Placing The Base Material. 201.3.2 Placing It Shall Be In Accordance With All The Requirements Of Subsection 200.3.2, Placing. 201.3.3 Spreading And Compacting It Shall Be In Accordance With All The Requirements Of Subsection 200.3.3, Spreading And Compacting. 201.3.4 Additional Filler Additional Filler, When Required And When Not Added At The Screening Plant, Shall Be Spread In A Uniform Layer Over The Loosely Spread Base Material As Specified By The Lgu Project Engineer, Scarified By Appropriate Heavy Equipment And Then Watered And Mixed As Described Above. These Materials Are Incidental To The Work And No Payment Shall Be Made By The Project To The Contractor. 201.3.5 Trial Sections Trial Sections Shall Conform In All Respects To The Requirements Specified In Subsection 200.3.4. 201.3.6 Tolerances The Aggregate Base Course Shall Be Laid To The Designed Level And Transverse Slopes Shown On The Plans. The Allowable Tolerances Shall Be In Accordance With Following: Permitted Variation From Design Thickness Of Layer ± 10 Mm Permitted Variation From Design Level Of Surface + 5 Mm -10 Mm Permitted Surface Irregularity Measured By 3-m Straight-edge 5 Mm Permitted Variation From Design Crossfall Or Camber ± 0.2% Permitted Variation From Design Longitudinal Grade Over 25 M In Length ± 0.1% 201.4 Environmental Measures During The Course Of Hauling Operations, The Contractor Must At All Times Provide The Necessary Cover For The Dump Body Of The Hauling Equipment To Prevent Accidental Spoilage Of Earth Materials That Will Injure The Travelling Public Or People Living Near By. The Travel Route Of The Hauling Equipment’s Must Always Be Moist To Prevent Blowing Up Of Dusts Particles. Likewise, The Contractor Must Always Observe The Noise Level Of The Exhaust Mufflers Of The Heavy Equipment’s To Be At Minimum. Otherwise, Exhaust Muffler Must Be Provided With Silencers To Reduce Noise Levels Of The Hauling Equipment’s. Travelling Speed Of All Hauling Equipment’s Must Be Reduce When Passing Populated Areas Or At The School Site During School Days. Item 311 – Portland Cement Concrete Pavement 311.1 Description This Item Shall Consist Of Pavement Of Portland Cement Concrete, With Or Without Reinforcement, Constructed On The Prepared Base In Accordance With This Specification And In Conformity With Lines, Grades, Thickness And Typical Cross-section Shown On The Plans. 311.2 Material Requirements 311.2.1 Portland Cement Only Type I Portland Cement Shall Be Used Unless Otherwise Provided For In The Special Provisions. Different Brands Or The Same Brands From Different Mills Shall Not Be Mixed Nor Shall They Be Used Alternately Unless The Mix Is Approved By The Lgu Project Engineer. Cement Which For Any Reason Has Become Partially Set Or Which Contains Lumps Of Caked Cement Will Be Rejected. Cement Salvaged From Discarded Or Used Bags Shall Not Be Used. Samples Of Cement Shall Be Obtained In Accordance With Aashto T 127. 311.2.2 Fine Aggregate It Shall Consist Of Natural Sand, Stone Screenings Or Other Inert Materials With Similar Characteristics, Or Combinations Thereof, Having Hard, Strong And Durable Particles. Fine Aggregate From Different Sources Of Supply Shall Not Be Mixed Or Stored In The Same Pile Nor Used Alternately In The Same Class Of Concrete Without The Approval Of The Lgu Project Engineer. It Shall Not Contain More Than Three (3) Mass Percent Of Material Passing The 0.075 Mm (no. 200 Sieve) By Washing Nor More Than One (1) Mass Percent Each Of Clay Lumps Or Shale. The Use Of Beach Sand Will Not Be Allowed Without The Approval Of The Lgu Project Engineer. If The Fine Aggregate Is Subjected To Five (5) Cycles Of The Sodium Sulfate Soundness Test, The Weighted Loss Shall Not Exceed 10 Mass Percent. The Fine Aggregate Shall Be Free From Injurious Amounts Of Organic Impurities. If Subjected To The Colorimetric Test For Organic Impurities And A Color Darker Than The Standard Is Produced, It Shall Be Rejected. However, When Tested For The Effect Of Organic Impurities Of Strength Of Mortar By Aashto T 71, The Fine Aggregate May Be Used If The Relative Strength At 7 And 28 Days Is Not Less Than 95 Mass Percent. The Fine Aggregate Shall Be Well-graded From Coarse To Fine And Shall Conform To Table 311.1 Table 311.1 – Grading Requirements For Fine Aggregate Sieve Designation Mass Percent Passing 9.5 Mm (3/8 In) 100 4.75 Mm (no. 4) 95 – 100 2.36 Mm (no. 8) - 1.18 Mm (no. 16) 45 – 80 0.600 Mm (no. 30) - 0.300 Mm (no. 50) 5 – 30 0.150 Mm (no. 100) 0 – 10 311.2.3 Coarse Aggregate It Shall Consist Of Crushed Stone, Gravel, Blast Furnace Slag, Or Other Approved Inert Materials Of Similar Characteristics, Or Combinations Thereof, Having Hard, Strong, Durable Pieces And Free From Any Adherent Coatings. It Shall Contain Not More Than One (1) Mass Percent Of Material Passing The 0.075 Mm (no. 200) Sieve, Not More Than 0.25 Mass Percent Of Clay Lumps, Nor More Than 3.5 Mass Percent Of Soft Fragments. If The Coarse Aggregate Is Subjected To Five (5) Cycles Of The Sodium Sulfate Soundness Test, The Weighted Loss Shall Not Exceed 12 Mass Percent. It Shall Have A Mass Percent Of Wear Not Exceeding 40 When Tested By Aashto T 96. If The Slag Is Used, Its Density Shall Not Be Less Than 1120 Kg/m3 (70 Lb./cu. Ft.). The Gradation Of The Coarse Aggregate Shall Conform To Table 311.2. Only One Grading Specification Shall Be Used From Any One Source. Table 311.2 – Grading Requirement For Coarse Aggregate Sieve Designation Mass Percent Passing Standard Mm Alternate U. S. Standard Grading A Grading B Grading C 75.00 3 In. 100 - - 63.00 2-1/2 In. 90-100 100 100 50.00 2 In. - 90-100 95-100 37.5 1-1/2 In. 25-60 35-70 - 25.0 1 In. - 0-15 35-70 19.0 ¾ In. 0-10 - - 12.5 ½ In. 0-5 0-5 10-30 4.75 No. 4 - - 0-5 311.2.4 Water Water Used In Mixing, Curing Or Other Designated Application Shall Be Reasonably Clean And Free Of Oil, Salt, Acid, Alkali, Grass Or Other Substances Injurious To The Finished Product. Water Will Be Tested In Accordance With And Shall Meet The Requirements Of Item 714, Water. Water Which Is Drinkable May Be Used Without Test. Where The Source Of Water Is Shallow, The Intake Shall Be So Enclosed As To Exclude Silt, Mud, Grass Or Other Foreign Materials. 311.2.5 Reinforcing Steel It Shall Conform To The Requirements Of Item 404, Reinforcing Steel. Dowels And Tie Bars Shall Conform To The Requirements Of Aashto M 31 Or M 42, Except That Rail Steel Shall Not Be Used For Tie Bars That Are To Be Bent And Re-straightened During Construction. Tie Bars Shall Be Deformed Bars. Dowels Shall Be Plain Round Bars. Before Delivery To The Site Of Work, One-half Of The Length Of Each Dowel Shall Be Painted With One Coat Of Approved Lead Or Tar Paint. The Sleeves For Dowel Bars Shall Be Metal Of Approved Design To Cover 50 Mm ( 2 Inches), Plus Or Minus 5 Mm (1/4 Inch) Of The Dowel, With A Closed End, And With A Suitable Stop To Hold The End Of The Sleeve At Least 25 Mm (1 Inch) From The End Of The Dowel. Sleeves Shall Be Of Such Design That They Do Not Collapse During Construction. 311.2.6 Joint Fillers Poured Joint Fillers Shall Be Mixed Asphalt And Mineral Or Rubber Filler. Preformed Joint Filler Shall Conform To The Applicable Requirements. It Shall Be Punched To Admit The Dowels Where Called For In The Plans. The Filler For Each Joint Shall Be Furnished In A Single Piece For The Full Depth And Width Required For The Joint. 311.2.7 Admixtures Air-entraining Admixture Shall Conform To The Requirements Of Aashto M 154. Chemical Admixtures, If Specified Or Permitted, Shall Conform To The Requirements Of Aashto M 194. Fly Ash, If Specified Or Permitted As A Mineral Admixture And As 20% Partial Replacement Of Portland Cement In Concrete Mix Shall Conform To The Requirements Of Astm C 618. Admixture Should Be Added Only To The Concrete Mix To Produce Some Desired Modifications To The Properties Of Concrete Where Necessary, But Not As Partial Replacement Of Cement. 311.2.8 Curing Materials Curing Materials Shall Conform To The Following Requirements As Specified; A) Burlap Cloth - Aashto M 182 B) Liquid Membrane Forming Compounds - Aashto M 148 C) Sheeting (film) Materials - Aashto M 171 Cotton Mats And Water-proof Paper Can Be Used. 311.2.9 Calcium Chloride/calcium Nitrate It Shall Conform To Aashto M 144, If Specified Or Permitted By The Lgu Project Engineer, As Accelerator. 311.2.10 Storage Of Cement And Aggregate All Cement Shall Be Stored, Immediately Upon Delivery At The Site, In Weatherproof Building Which Will Protect The Cement From Dampness. The Floor Shall Be Raised From The Ground. The Buildings Shall Be Placed In Locations Approved By The Lgu Project Engineer. Provisions For Storage Shall Be Ample, And The Shipments Of Cement As Received Shall Be Separately Stored In Such A Manner As To Allow The Earliest Deliveries To Be Used First And To Provide Easy Access For Identification And Inspection Of Each Shipment. Storage Buildings Shall Have Capacity For Storage Of A Sufficient Quantity Of Cement To Allow Sampling At Least Twelve (12) Days Before The Cement Is To Be Used. Bulk Cement, If Used, Shall Be Transferred To Elevated Air Tight And Weatherproof Bins. Stored Cement Shall Meet The Test Requirements At Any Time After Storage When Retest Is Ordered By The Lgu Project Engineer. At The Time Of Use, All Cement Shall Be Free-flowing And Free Of Lumps. The Handling And Storing Of Concrete Aggregates Shall Be Such As To Prevent Segregation Or The Inclusion Of Foreign Materials. The Lgu Project Engineer May Require That Aggregates Be Stored On Separate Platforms At Satisfactory Locations. In Order To Secure Greater Uniformity Of Concrete Mix, The Lgu Project Engineer May Require That The Coarse Aggregate Be Separated Into Two Or More Sizes. Different Sizes Of Aggregate Shall Be Stored In Separate Bins Or In Separate Stockpiles Sufficiently Removed From Each Other To Prevent The Material At The Edges Of The Piles From Becoming Intermixed. 311.2.11 Proportioning, Consistency And Strength Of Concrete The Contractor Shall Prepare The Design Mix Based On The Absolute Volume Method As Outlined In The American Concrete Institute (aci) Standard 211.1, “recommended Practice For Selecting Proportions For Normal And Heavyweight Concrete”. It Is The Intent Of This Specification To Require At Least 364 Kg Of Cement Per Cubic Meter Of Concrete To Meet The Minimum Strength Requirements. The Lgu Project Engineer Shall Determine From Laboratory Tests Of The Materials To Be Used, The Cement Content And The Proportions Of Aggregate And Water That Will Produce Workable Concrete Having A Slump Of Between 40 And 75 Mm (1-1/2 And 3 Inches) If Not Vibrated Or Between 10 And 40 Mm (1/2 And 1-1/2 Inches) If Vibrated, And A Flexural Strength Of Not Less Than 3.8 Mpa (550 Psi) When Tested By The Third-point Method Or 4.5 Mps (650 Psi) When Tested By The Mid-point Method At Fourteen (14) Days In Accordance With Aashto T97 And T177, Respectively; Or A Compressive Strength Of 24.1 Mps (3500 Psi) For Cores Taken At Fourteen (14) Days And Tested In Accordance With Aashto T24. Slump Shall Be Determined Using Aashto T 119. The Designer Shall Consider The Use Of Lean Concrete (econcrete) Mixtures Using Local Materials Or Specifically Modified Conventional Concrete Mixes In Base Course And In The Lower Course Composite, Monolithic Concrete Pavements Using A Minimum Of 75 Mm (3 Inches) Of Conventional Concrete As The Surface Course. The Mix Design Shall Be Submitted To The Lgu Project Engineer For Approval And Shall Be Accompanied With Certified Test Data From An Approved Laboratory Demonstrating The Adequacy Of The Mix Design. A Change In The Source Of Materials During The Progress Of Work May Necessitate A New Design Mix. 311.3 Construction Requirements 311.3.1 Quality Control Of Concrete 1. General The Contractor Shall Be Responsible For The Quality Control Of All Materials During The Handling, Blending, And Mixing And Placement Operations. 2. Quality Control Plan The Contractor Shall Furnish The Lgu Project Engineer A Quality Control Plan Detailing His Production Control Procedures And The Type And Frequency Of Sampling And Testing To Insure That The Concrete Produces Complies With The Specifications. The Lgu Project Engineer Shall Be Provided Free Access To Recent Plant Production Records, And If Requested, Informational Copies Of Mix Design, Materials Certifications And Sampling And Testing Reports. 3. Qualification Of Workmen Experienced And Qualified Personnel Shall Perform All Batching Or Mixing Operation For The Concrete Mix, And Shall Be Present At The Plant And Job Site To Control The Concrete Productions Whenever The Plant Is In Operation. They Shall Be Identified And Duties Defined As Follows: A. Concrete Batcher. The Person Performing The Batching Or Mixing Operation Shall Be Capable Of Accurately Conducting Aggregate Surface Moisture Determination And Establishing Correct Scale Weights For Concrete Materials. He Shall Be Capable Of Assuring That The Proportioned Batch Weights Of Materials Are In Accordance With The Mix Design. B. Concrete Technician. The Person Responsible For Concrete Production Control And Sampling And Testing For Quality Control Shall Be Proficient In Concrete Technology And Shall Have A Sound Knowledge Of The Specifications As They Relate To Concrete Production. He Shall Be Capable Of Conducting Tests On Concrete And Concrete Materials In Accordance With These Specifications. He Shall Be Capable Of Adjusting Concrete Mix Designs For Improving Workability And Specification Compliance And Preparing Trial Mix Designs. He Shall Be Qualified To Act As The Concrete Batcher In The Batcher’s Absence. 4. Quality Control Testing The Contractor Shall Perform All Sampling, Testing And Inspection Necessary To Assure Quality Control Of The Component Materials And The Concrete. The Contractor Shall Be Responsible For Determining The Gradation Of Fine And Coarse Aggregates And For Testing The Concrete Mixture For Slump, Air Content, Water-cement Ratio And Temperature. He Shall Conduct His Operations So As To Produce A Mix Conforming To The Approved Mix Design. 5. Documentation The Contractor Shall Maintain Adequate Records Of All Inspections And Tests. The Records Shall Indicate The Nature And Number Of Observations Made, The Number And Type Of Deficiencies Found, The Quantities Approved And Rejected, And Nature Of Any Corrective Action Taken. The Lgu Project Engineer May Take Independent Assurance Samples At Random Location For Acceptance Purposes As He Deems Necessary. 311.3.2 Equipment Equipment And Tools Necessary For Handling Materials And Performing All Parts Of The Work Shall Be Approved By The Lgu Project Engineer As To Design, Capacity And Mechanical Condition. The Equipment Shall Be At The Jobsite Sufficiently Ahead Of The Start Of Construction Operations To Be Examined Thoroughly And Approved. 1. Batching Plant And Equipment A. General. The Batching Shall Include Bins, Weighing Hoppers, And Scales For The Fine Aggregate And For Each Size Of Coarse Aggregate. If Cement Is Used In Bulk, A Bin, A Hopper, And Separate Scale For Cement Shall Be Included. The Weighing Hopper Shall Be Properly Sealed And Vented To Preclude Dusting Operation. The Batch Plant Shall Be Equipped With A Suitable Non-resettable Batch Counter Which Will Correctly Indicate The Number Of Batches Proportioned. B. Bins And Hoppers. Bins With Adequate Separate Compartments For Fine Aggregate And For Each Size Of Coarse Aggregate Shall Be Provided In The Batching Plant. C. Scales. Scales For Weighing Aggregates And Cement Shall Be Of Either The Beam Type Or The Spring-less-dial Type. They Shall Be Accurate Within One-half Percent (0.5%) Throughout The Range Of Use. Poises Shall Be Designed To Be Locked In Any Position And To Prevent Unauthorized Change. Scales Shall Be Inspected And Sealed As Often As The Lgu Project Engineer May Deem Necessary To Assure Their Continued Accuracy. D. Automatic Weighing Devices. Unless Otherwise Allowed On The Contract, Batching Plants Shall Be Equipped With Automatic Weighing Devices Of An Approved Type To Proportion Aggregates And Bulk Cement. 2. Mixers. A. General. Concrete May Be Mixed At The Site Of Construction Or At A Central Plant, Or Wholly Or In Part In Truck Mixers. Each Mixer Shall Have A Manufacturer’s Plate Attached In A Prominent Place Showing The Capacity Of The Drum In Terms Of Volume Of Mixed Concrete And The Speed Of Rotation Of The Mixing Drum Or Blades. B. Mixers At Site Of Construction. Mixing Shall Be Done In An Approved Mixer Capable Of Combining The Aggregates, Cement And Water Into A Thoroughly Mixed And Uniform Mass Within The Specified Mixing Period And Discharging And Distributing The Mixture Without Segregation On The Prepared Grade. The Mixer Shall Be Equipped With An Approved Timing Device Which Will Automatically Lock The Discharge Lever When The Drum Has Been Charged And Released It At The End Of The Mixing Period. In Case Of Failure Of The Timing Device, The Mixer May Be Used For The Balance Of The Day While It Is Being Repaired, Provided That Each Batch Is Mixed 90 Seconds. The Mixer Shall Be Equipped With A Suitable Non-resettable Batch Counter Which Shall Correctly Indicate The Number Of The Batches Mixed. C. Truck Mixer And Truck Agitators. Truck Mixers Used For Mixing And Hauling Concrete, And Truck Agitators Used For Hauling Central-mixed Concrete, Shall Conform To The Requirements Of Aashto M 157. D. Non-agitator Truck. Bodies Of Non-agitating Hauling Equipment For Concrete Shall Be Smooth, Mortar-tight Metal Containers And Shall Be Capable Of Discharging The Concrete At A Satisfactory Controlled Rate Without Segregation. 3. Paving And Finishing Equipment The Concrete Shall Be Placed With An Approved Paver Designed To Spread, Consolidate, Screed And Float Finish The Freshly Placed Concrete In One Complete Pass Of The Machine In Such A Manner That A Minimum Of Hand Finishing Will Be Necessary To Provide A Dense And Homogeneous Pavement In Conformance With The Plans And Specifications. The Finishing Machine Shall Be Equipped With At Least Two (2) Oscillating Type Transverse Screed. Vibrators Shall Operate At A Frequency Of 8,300 To 9,600 Impulses Per Minute Under Load At A Maximum Spacing Of 60 Cm. 4. Concrete Saw The Contractor Shall Provide Sawing Equipment In Adequate Number Of Units And Power To Complete The Sawing With Water-cooled Diamond Edge Saw Blade Or An Abrasive Wheel To The Required Dimensions And At The Required Rate. He Shall Provide At Least One (1) Stand-by Saw In Good Working Condition And With An Ample Supply Of Saw Blades. 5. Forms Forms Shall Be Of Steel, Of An Approved Section, And Of Depth Equal To The Thickness Of The Pavement At The Edge. The Base Of The Forms Shall Be Of Sufficient Width To Provide Necessary Stability In All Directions. The Flange Braces Must Extend Outward On The Base To Not Less Than 2/3 The Height Of The Form. All Forms Shall Be Rigidly Supported On Bed Of Thoroughly Compacted Material During The Entire Operation Of Placing And Finishing The Concrete. Forms Shall Be Provided With Adequate Devices For Secure Setting So That When In Place, They Will Withstand, Without Visible Spring Or Settlement, The Impact And Vibration Of The Consolidation And Finishing Or Paving Equipment. 311.3.3 Preparation Of Grade After The Sub-grade Of Base Has Been Placed And Compacted To The Required Density, The Areas Which Will Support The Paving Machine And The Grade On Which The Pavement Is To Be Constructed Shall Be Trimmed To The Proper Elevation By Means Of A Properly Designed Machine Extending The Prepared Work Areas Compacted At Least 60 Cm Beyond Each Edge Of The Proposed Concrete Pavement. If Loss Of Density Results From The Trimming Operations, It Shall Be Restored By Additional Compaction Before Concrete Is Placed. If Any Traffic Is Allowed To Use The Prepared Sub-grade Or Base, The Surface Shall Be Checked And Corrected Immediately Ahead Of The Placing Concrete. The Sub-grade Or Base Shall Be Uniformly Moist When The Concrete Is Placed. 311.3.4 Setting Forms 1. Base Support. The Foundation Under The Forms Shall Be Hard And True To Grade So That The Form When Set Will Be Firmly In Contact For Its Whole Length And At The Specified Grade. (any Roadbed, Which At The Form Line Is Found Below Established Grade, Shall Be Filled With Approved Granular Materials To Grade In Lifts Of Three (3) Cm Or Less, And Thoroughly Re-rolled Or Tamped.) Imperfections Or Variations Above Grade Shall Be Corrected By Tamping Or By Cutting As Necessary. 2. Form Setting Forms Shall Be Set Sufficiently In Advance Of The Point Where Concrete Is Being Placed. After The Forms Have Been Set To Correct Grade, The Grade Shall Be Thoroughly Tamped, Mechanically Or By Hand, At Both The Inside And Outside Edges Of The Base Of The Forms. The Forms Shall Not Deviate From True Line Bv More Than One (1) Cm At Any Point. 3. Grade And Alignment The Alignment And Grade Elevations Of The Forms Shall Be Checked And Corrections Made By The Contractor Immediately Before Placing The Concrete. Testing As To Crown And Elevation, Prior To Placing Of Concrete Can Be Made By Means Of Holding An Approved Template In A Vertical Position And Moved Backward And Forward On The Forms. When Any Form Has Been Disturbed Or Any Grade Has Become Unstable, The Form Shall Be Reset And Rechecked. 311.3.5 Conditioning Of Sub-grade Or Base Course When Side Forms Have Been Securely Set To Grade, The Sub-grade Or Base Course Shall Be Brought To Proper Cross-section. High Areas Shall Be Trimmed To Proper Elevation. Low Areas Shall Be Filled And Compacted To A Condition Similar To That Of Surrounding Grade. The Finished Grade Shall Be Maintained In A Smooth And Compacted Condition Until The Pavement Is Placed. Unless Waterproof Sub-grade Or Base Course Cover Material Is Specified, The Sub-grade Or Base Course Shall Be Uniformly Moist When The Concrete Is Placed. If It Subsequently Becomes Too Dry, The Sub-grade Or Base Course Shall Be Sprinkled, But The Method Of Sprinkling Shall Not Be Such As To Form Mud Or Pools Of Water. 311.3.6 Handling, Measuring And Batching Materials The Batch Plant Site, Layout, Equipment And Provisions For Transporting Material Shall Be Such As To Assure A Continuous Supply Of Material To The Work. Stockpiles Shall Be Built Up In Layers Of Not More Than One (1) Meter In Thickness. Each Layer Shall Be Completely In Place Before Beginning The Next Which Shall Not Be Allowed To “cone” Down Over The Next Lower Layer. Aggregates From Different Sources And Of Different Grading Shall Not Be Stockpiled Together. All Washed Aggregates And Aggregates Produced Or Handled By Hydraulic Methods, Shall Be Stockpiled Or Binned For Draining At Least Twelve (12) Hours Before Being Batched. When Mixing Is Done At The Side Of The Work, Aggregates Shall Be Transported From The Batching Plant To The Mixer In Batch Boxes, Vehicle Bodies, Or Other Containers Of Adequate Capacity And Construction To Properly Carry The Volume Required. Partitions Separating Batches Shall Be Adequate And Effective To Prevent Spilling From One Compartment To Another While In Transit Or Being Dumped. When Bulk Cement Is Used, The Contractor Shall Use A Suitable Method Of Handling The Cement From Weighing Hopper To Transporting Container Or Into The Batch Itself For Transportation To The Mixer, With Chute, Boot Or Other Approved Device, To Prevent Loss Of Cement, And To Provide Positive Assurance Of The Actual Presence In Each Batch Of The Entire Cement Content Specified. Bulk Cement Shall Be Transported To The Mixer In Tight Compartments Carrying The Full Amount Of Cement Required For The Batch. However, If Allowed In The Special Provisions, It May Be Transported Between The Fine And Coarse Aggregate. When Cement Is Placed In Contact With The Aggregates, Batches May Be Rejected Unless Mixed Within 1-1/2 Hours Of Such Contact. Cement In Original Shipping Packages May Be Transported On Top Of The Aggregates, Each Batch Containing The Number Of Sacks Required By The Job Mix. The Mixer Shall Be Charged Without Loss Of Cement. Batching Shall Be So Conducted As To Result In The Weight To Each Material Required Within A Tolerance Of One (1) Percent For The Cement And Two (2) Percent For Aggregates. Water May Be Measured Either By Volume Or By Weight. The Accuracy Of Measuring The Water Shall Be Within A Range Of Error Of Not Over Than One (1) Percent. Unless The Water Is To Be Weighed, The Water-measuring Equipment Shall Include An Auxiliary Tank From Which The Measuring Tank Shall Be Equipped With An Outside Tap And Valve To Provide Checking The Setting, Unless Other Means Are Provided For Readily And Accurately Determining The Amount Of Water In The Tank. The Volume Of The Auxiliary Tank Shall Be At Least Equal To That Of The Measuring Tank. 311.3.7 Mixing Concrete The Concrete May Be Mixed At The Site Of The Work In A Central-mix Plant, Or In Truck Mixers. The Mixer Shall Be Of An Approved Type And Capacity. Mixing Time Will Be Measured From The Time All Materials, Except Water, Are In The Drum. Ready-mixed Concrete Shall Be Mixed And Delivered In Accordance With Requirements Of Aashto M 157, Except That The Minimum Required Revolutions At The Mixing Speed For Transit-mixed Concrete May Be Reduced To Not Less Than That Recommended By The Mixer Manufacturer. The Number Of Revolutions Recommended By The Mixer Manufacturer Shall Be Indicated On The Manufacturer’s Serial Plate Attached To The Mixer. The Contractor Shall Furnish Test Data Acceptable To The Lgu Project Engineer Verifying That The Make And Model Of The Mixer Will Produce Uniform Concrete Conforming To The Provision Of Aashto M 157 At The Reduced Number Of Revolutions Shown On The Serial Plate. When Mixed At The Site Or In A Central Mixing Plant, The Mixing Time Shall Not Be Less Than Fifty (50) Seconds Nor More Than Ninety (90) Seconds, Unless Mixer Performance Tests Prove Adequate Mixing Of The Concrete Is A Shorter Time Period. Four (4) Seconds Shall Be Added To The Specified Mixing Time If Timing Starts At The Instant The Skip Reaches Its Maximum Raised Positions. Mixing Time Ends When The Discharge Chute Opens. Transfer Time In Multiple Drum Mixers Is Included In Mixing Time. The Contents Of An Individual Mixer Drum Shall Be Removed Before A Succeeding Batch Is Emptied Therein. The Mixer Shall Be Operated At The Drum Speed As Shown On The Manufacturer’s Name Plate Attached On The Mixer. Any Concrete Mixed Less Than The Specified Time Shall Be Discarded And Disposed Off By The Contractor At His Expense. The Volume Of Concrete Mixed Per Batch Shall Not Exceed The Mixer’s Nominal Capacity In Cubic Metre, As Shown On The Manufacturer’s Standard Rating Plate On The Mixer, Except That An Overload Up To Ten (10) Percent Above The Mixer’s Nominal Capacity May Be Permitted Provided Concrete Test Data For Strength, Segregation, And Uniform Consistency Are Satisfactory, And Provided No Spillage Of Concrete Takes Place. The Batches Shall Be So Charged Into The Drum That A Portion Of The Mixing Water Shall Be Entered In Advance Of The Cement And Aggregates. The Flow Of Water Shall Be Uniform And All Water Shall Be In The Drum By The End Of The First Fifteen (15) Seconds Of The Mixing Period. The Throat Of The Drum Shall Be Kept Free Of Such Accumulations As May Restrict The Free Flow Of Materials Into The Drum. Mixed Concrete From The Central Mixing Plant Shall Be Transported In Truck Mixers, Truck Agitators Or Non-agitating Truck Specified In Subsection 311.3.2, Equipment. The Time Elapsed From The Time Water Is Added To The Mix Until The Concrete Is Deposited In Place At The Site Shall Not Exceed Forty Five (45) Minutes When The Concrete Is Hauled In Non-agitating Trucks, Nor Ninety (90) Minutes When Hauled In Truck Mixers Or Truck Agitators, Except That In Hot Weather Or Under Other Conditions Contributing To Quick Hardening Of The Concrete, The Maximum Allowable Time May Be Reduced By The Lgu Project Engineer. In Exceptional Cases And When Volumetric Measurements Are Authorized For Small Project Requiring Less Than 75 Cu.m. Of Concrete Per Day Of Pouring, The Weight Proportions Shall Be Converted To Equivalent Volumetric Proportions. In Such Cases, Suitable Allowance Shall Be Made For Variations In The Moisture Condition Of The Aggregates, Including The Bulking Effect In The Fine Aggregate. Batching And Mixing Shall Be In Accordance With Astm C 685, Section 6 Through 9. Concrete Mixing By Chute Is Allowed Provided That A Weighing Scale For Determining The Batch Weight Will Be Used. Retendering Concrete By Adding Water Or By Other Means Shall Not Be Permitted, Except That When Concrete Is Delivered In Truck Mixers, Additional Water May Be Added To The Batch Materials And Additional Mixing Performed To Increase The Slump To Meet The Specified Requirements, If Permitted By The Lgu Project Engineer, Provided All These Operations Are Performed Within Forty-five (45) Minutes After The Initial Mixing Operation And The Water-cement Ratio Is Not Exceeded. Concrete That Is Not Within The Specified Slump Limits At The Time Of Placement Shall Not Be Used. Admixtures For Increasing The Workability Or For Accelerating The Setting Of The Concrete Will Be Permitted Only When Specifically Approved By The Lgu Project Engineer. 311.3.8 Limitation Of Mixing No Concrete Shall Be Mixed, Placed Or Finished When Natural Light Is Insufficient, Unless An Adequate And Approved Artificial Lighting System Is Operated. During Hot Weather, The Lgu Project Engineer Shall Require That Steps Be Taken To Prevent The Temperature Of Mixed Concrete From Exceeding A Maximum Temperature Of (900f 320c). Concrete Not In Place Within Ninety (90) Minutes From The Time The Ingredients Were Charged Into The Mixing Drum Or That Has Developed Initial Set Shall Not Be Used. Retendering Of Concrete Or Mortar Which Has Partially Hardened, That Is Remixing With Or Without Additional Cement, Aggregate, Or Water, Shall Not Be Permitted. In Order That The Concrete May Be Properly Protected Against The Effects Of Rain Before The Concrete Is Sufficiently Hardened, The Contractor Will Be Required To Have Available At All Times Materials For The Protection Of The Edges And Surface Of The Unhardened Concrete. 311.3.9 Placing Concrete Concrete Shall Be Deposited In Such A Manner To Require Minimal Rehandling. Unless Truck Mixers Or Non-agitating Hauling Equipment Are Equipped With Means To Discharge Concrete Without Segregation Of The Materials, The Concrete Shall Be Unloaded Into An Approved Spreading Device And Mechanically Spread On The Grade In Such A Manner As To Prevent Segregation. Placing Shall Be Continuous Between Transverse Joints Without The Use Of Intermediate Bulkheads. Necessary Hand Spreading Shall Be Done With Shovels, Not Rakes. Workmen Shall Not Be Allowed To Walk In The Freshly Mixed Concrete With Boots Or Shoes Coated With Earth Or Foreign Substances. When Concrete Is To Be Placed Adjoining A Previously Constructed Lane And Mechanical Equipment Will Be Operated Upon The Existing Lane, That Previously Constructed Lane Shall Have Attained The Strength For Fourteen (14) Day Concrete. If Only Finishing Equipment Is Carried On The Existing Lane, Paving In Adjoining Lanes May Be Permitted After Three (3) Days. Concrete Shall Be Thoroughly Consolidated Against And Along The Faces Of All Forms And Along The Full Length And On Both Sides Of All Joint Assemblies, By Means Of Vibrators Inserted In The Concrete. Vibrators Shall Not Be Permitted To Come In Contact With A Joint Assembly, The Grade, Or A Side Form. In No Case Shall The Vibrator Be Operated Longer Than Fifteen (15) Seconds In Any One Location. Concrete Shall Be Deposited As Near As Possible To The Expansion And Contraction Joints Without Disturbing Them, But Shall Not Be Dumped From The Discharge Bucket Or Hopper Into A Joint Assembly Unless The Hopper Is Well Centered On The Joint Assembly. Should Any Concrete Material Fall On Or Be Worked Into The Surface Of A Complete Slab, It Shall Be Removed Immediately. 311.3.10 Test Specimens As Work Progresses, At Least One (1) Set Consisting Of Three (3) Concrete Beam Test Specimens, 150 Mm X 150 Mm X 525 Mm Or 900 Mm Shall Be Taken From Each 330 M2 Of Pavement, 230 Mm Depth, Or Fraction Thereof Placed Each Day. Test Specimens Shall Be Made Under The Supervision Of The Lgu Project Engineer, And The Contractor Shall Provide All Concrete And Other Facilities Necessary In Making The Test Specimens And Shall Protect Them From Damage By Construction Operations. Cylinder Samples Shall Not Be Used As Substitute For Determining The Adequacy Of The Strength Of Concrete. The Beams Shall Be Made, Cured, And Tested In Accordance With Aashto T 23 And T 97. 311.3.11 Strike-off Of Concrete And Placement Of Reinforcement Following The Placing Of The Concrete, It Shall Be Struck Off To Conform To The Cross-section Shown On The Plans And To An Elevation Such That When The Concrete Is Properly Consolidated And Finished, The Surface Of The Pavement Will Be At The Elevation Shown On The Plans. When Reinforced Concrete Pavement Is Placed In Two (2) Layers, The Bottom Layer Shall Be Struck Off And Consolidated To Such Length And Depth That The Sheet Of Fabric Or Bar Mat May Be Laid Full Length On The Concrete In Its Final Position Without Further Manipulation. The Reinforcement Shall Then Be Placed Directly Upon The Concrete, After Which The Top Layer Of The Concrete Shall Be Placed, Struck Off And Screened. Any Portion Of The Bottom Layer Of Concrete Which Has Been Placed More Than 30 Minutes Without Being Covered With The Top Layer Shall Be Removed And Replaced With Freshly Mixed Concrete At The Contractor’s Expense. When Reinforced Concrete Is Placed In One Layer, The Reinforcement May Be Firmly Positioned In Advance Of Concrete Placement Or It May Be Placed At The Depth Shown On The Plans In Plastic Concrete, After Spreading By Mechanical Or Vibratory Means. Reinforcing Steel Shall Be Free From Dirt, Oil, Paint, Grease, Mill Scale And Loose Or Thick Rust Which Could Impair Bond Of The Steel With The Concrete. 311.3.12 Joints Joints Shall Be Constructed Of The Type And Dimensions, And At The Locations Required By The Plans Or Special Provisions. All Joints Shall Be Protected From The Intrusion Of Injurious Foreign Material Until Sealed. 1. Longitudinal Joint Deformed Steel Tie Bars Of Specified Length, Size, Spacing And Materials Shall Be Placed Perpendicular To The Longitudinal Joints, They Shall Be Placed By Approved Mechanical Equipment Or Rigidly Secured By Chair Or Other Approved Supports To Prevent Displacement. Tie Bars Shall Not Be Painted Or Coated With Asphalt Or Other Materials Or Enclosed In Tubes Or Sleeves. When Shown On The Plans And When Adjacent Lanes Of Pavement Are Constructed Separately, Steel Side Forms Shall Be Used Which Will Form A Keyway Along The Construction Joint. Tie Bars, Except Those Made Of Rail Steel, May Be Bent At Right Angles Against The Form Of The First Lane Constructed And Straightened Into Final Position Before The Concrete Of The Adjacent Lane Is Placed, Or In Lieu Of Bent Tie Bars, Approved Two-piece Connectors May Be Used. Longitudinal Formed Joints Shall Consist Of A Groove Or Cleft, Extending Downward From And Normal To, The Surface Of The Pavement. These Joints Shall Be Effected Or Formed By An Approved Mechanically Or Manually Operated Device To The Dimensions And Line Indicated On The Plans And While The Concrete Is In A Plastic State. The Groove Or Cleft Shall Be Filled With Either A Premolded Strip Or Poured Material As Required. The Longitudinal Joints Shall Be Continuous, There Shall Be No Gaps In Either Transverse Or Longitudinal Joints At The Intersection Of The Joints. Longitudinal Sawed Joints Shall Be Cut By Means Of Approved Concrete Saws To The Depth, Width And Line Shown On The Plans. Suitable Guide Lines Or Devices Shall Be Used To Assure Cutting The Longitudinal Joint On The True Line. The Longitudinal Joint Shall Be Sawed Before The End Of The Curing Period Or Shortly Thereafter And Before Any Equipment Or Vehicles Are Allowed On The Pavement. The Sawed Area Shall Be Thoroughly Cleaned And, If Required, The Joint Shall Immediately Be Filled With Sealer. Longitudinal Pavement Insert Type Joints Shall Be Formed By Placing A Continuous Strip Of Plastic Materials Which Will Not React Adversely With The Chemical Constituent Of The Concrete. 2. Transverse Expansion Joint The Expansion Joint Filler Shall Be Continuous From Form To Form, Shaped To Sub-grade And To The Keyway Along The Form. Preformed Joint Filler Shall Be Furnished In Lengths Equal To The Pavement Width Or Equal To The Width Of One Lane. Damaged Or Repaired Joint Filler Shall Not Be Used. The Expansion Joint Filler Shall Be Held In A Vertical Position. An Approved Installing Bar, Or Other Device, Shall Be Used If Required To Secure Preformed Expansion Joint Filler At The Proper Grade And Alignment During Placing And Finishing Of The Concrete. Finished Joint Shall Not Deviate More Than 6 Mm From A Straight Line. If Joint Fillers Are Assembled In Sections, There Shall Be No Offsets Between Adjacent Units. No Plugs Of Concrete Shall Be Permitted Anywhere Within The Expansion Space. 3. Transverse Contraction Joint/weakened Joint When Shown On The Plans, It Shall Consist Of Planes Of Weakness Created By Forming Or Cutting Grooves In The Surface Of The Pavement And Shall Include Load Transfer Assemblies. The Depth Of The Weakened Plane Joint Should At All Times Not Be Less Than 50 Mm, While The Width Should Not Be More Than 6 Mm. A. Transverse Strip Contraction Joint. It Shall Be Formed By Installing A Parting Strip To Be Left In Place As Shown On The Plans. B. Formed Groove. It Shall Be Made By Depressing An Approved Tool Or Device Into The Plastic Concrete. The Tool Or Device Shall Remain In Place At Least Until The Concrete Has Attained Its Initial Set And Shall Then Be Removed Without Disturbing The Adjacent Concrete, Unless The Device Is Designed To Remain In The Joint. C. Sawed Contraction Joint. It Shall Be Created By Sawing Grooves In The Surface Of The Pavement Of The Width Not More Than 6 Mm, Depth Should At All Times Not Be Less Than 50 Mm, And At The Spacing And Lines Shown On The Plans, With An Approved Concrete Saw. After Each Joint Is Sawed, It Shall Be Thoroughly Cleaned Including The Adjacent Concrete Surface. Sawing Of The Joint Shall Commence As Soon As The Concrete Has Hardened Sufficiently To Permit Sawing Without Excessive Raveling, Usually 4 To 24 Hours. All Joints Shall Be Sawed Before Uncontrolled Shrinkage Cracking Takes Place. If Necessary, The Sawing Operations Shall Be Carried On During The Day Or Night, Regardless Of Weather Conditions. The Sawing Of Any Joint Shall Be Omitted If Crack Occurs At Or Near The Joint Location Prior To The Time Of Sawing. Sawing Shall Be Discounted When A Crack Develops Ahead Of The Saw. In General, All Joints Should Be Sawed In Sequence. If Extreme Condition Exist Which Make It Impractical To Prevent Erratic Cracking By Early Sawing, The Contraction Joint Groove Shall Be Formed Prior To Initial Set Of Concrete As Provided Above. 4. Transverse Construction Joint It Shall Be Constructed When There Is An Interruption Of More Than 30 Minutes In The Concreting Operations. No Transverse Joint Shall Be Constructed Within 1.50 M Of An Expansion Joint, Contraction Joint, Or Plane Of Weakness. If Sufficient Concrete Has Been Mixed At The Time Of Interruption To Form A Slab Of At Least 1.5 M Long, The Excess Concrete From The Last Preceding Joint Shall Be Removed And Disposed Off As Directed. 5. Load Transfer Device Dowel, When Used, Shall Be Held In Position Parallel To The Surface And Center Line Of The Slab By A Metal Device That Is Left In The Pavement. The Portion Of Each Dowel Painted With One Coat Of Lead Or Tar, In Conformance With The Requirements Of Item 404, Reinforcing Steel, Shall Be Thoroughly Coated With Approved Bituminous Materials, E.g., Mc-70, Or An Approved Lubricant, To Prevent The Concrete From Binding To That Portion Of The Dowel. The Sleeves For Dowels Shall Be Metal Designed To Cover 50 Mm Plus Or Minus 5 Mm (1/4 Inch), Of The Dowel, With A Watertight Closed End And With A Suitable Stop To Hold The End Of The Sleeves At Least 25 Mm (1 Inch) From The End Of The Dowel. In Lieu Of Using Dowel Assemblies At Contraction Joints, Dowel May Be Placed In The Full Thickness Of Pavement By A Mechanical Device Approved By The Lgu Project Engineer. 311.3.13 Final Strike-off (consolidation And Finishing) 1. Sequence The Sequence Of Operations Shall Be The Strike-off And Consolidation, Floating And Removal Of Laitance, Straight-edging And Final Surface Finish. Work Bridges Or Other Devices Necessary To Provide Access To The Pavement Surface For The Purpose Of Finishing Straight-edging, And Make Corrections As Hereinafter Specified, Shall Be Provided By The Contractor. In General, The Addition Of Water To The Surface Of The Concrete To Assist In Finishing Operations Will Not Be Permitted. If The Application Of Water To The Surface Is Permitted, It Shall Be Applied As Fog Spray By Means Of An Approve Spray Equipment. 2. Finishing Joints The Concrete Adjacent To Joints Shall Be Compacted Or Firmly Placed Without Voids Or Segregation Against The Joint Material Assembly, Also Under And Around All Load Transfer Devices, Joint Assembly Units, And Other Features Designed To Extend Into The Pavement. Concrete Adjacent To Joints Shall Be Mechanically Vibrated As Required In Subsection 311.3.9, Placing Concrete. After The Concrete Has Been Placed And Vibrated Adjacent To The Joints As Required In Subsection 311.3.9, The Finishing Machine Shall Be Brought Forward, Operating In A Manner To Avoid Damage Or Misalignment Of Joints. If Uninterrupted Operation Of The Finishing Machine, To Over And Beyond The Joints Causes Segregation Of Concrete, Damage To, Or Misalignment Of The Joints, The Finishing Machine Shall Be Stopped When The Front Screed Is Approximately 20 Cm (8 Inches) From The Joint. Segregated Concrete Shall Be Removed From In Front Of And Off The Joint. The Front Screed Shall Be Lifted And Set Directly On Top Of The Joint And The Forward Motion Of The Finishing Machine Resumed. When The Second Screed Is Close Enough To Permit The Excess Mortar In Front Of It To Flow Over The Joint, It Shall Be Lifted And Carried Over The Joint. Thereafter, The Finishing Machine May Be Run Over The Joint Without Lifting The Screeds, Provided There Is No Segregated Concrete Immediately Between The Joint And The Screed Or On Top Of The Joint. 3. Machine Finishing A. Non-vibratory Method. The Concrete Shall Be Distributed Or Spread As Soon As Placed. As Soon As The Concrete Has Been Placed, It Shall Be Struck Off And Screwed By An Approved Finishing Machine. The Machine Shall Go Over Each Area Of Pavement As Many Times And At Such Intervals As Necessary To Give The Proper Compaction And Leave A Surface Of Uniform Texture. Excessive Operation Over A Given Area Shall Be Avoided. The Tops Of The Forms Shall Be Kept Clean By An Effective Device Attached To The Machine And The Travel Of The Machine On The Forms Shall Be Maintained True Without Wobbling Or Other Variation Tending To Affect The Precision Finish. During The First Pass Of The Finishing Machine, A Uniform Ridge Of Concrete Shall Be Maintained Ahead Of The Front Screed In Its Entire Length. B. Vibratory Method. When Vibration Is Specified, Vibrators For Full Width Vibration Of Concrete Paving Slabs, Shall Meet The Requirements In Subsection 311.3.2, Equipment. If Uniform And Satisfactory Density Of The Concrete Is Not Obtained By The Vibratory Method At Joints, Along Forms, At Structures, And Throughout The Pavement, The Contractor Will Be Required To Furnish Equipment And Method Which Will Produce Pavement Conforming To The Specifications. All Provisions In Item (a) Above Not In Conflict With The Provisions For The Vibratory Method Shall Govern. 4. Hand Finishing Hand Finishing Methods May Only Be Used Under The Following Conditions: A. In The Event Of Breakdown Of The Mechanical Equipment, Hand Methods May Be Used To Finish The Concrete Already Deposited On The Grade. B. In Narrow Widths Or Areas Of Irregular Dimensions Where Operations Of The Mechanical Equipment Is Impractical, Hand Methods May Be Used. Concrete, As Soon As Placed, Shall Be Struck Off And Screeded. An Approved Portable Screed Shall Be Used. A Second Screed Shall Be Provided For Striking Off The Bottom Layer Of Concrete If Reinforcement Is Used. The Screed For The Surface Shall Be At Least 60 Cm (2 Feet) Longer Than The Maximum Width Of The Slab To Be Struck Off. It Shall Be Of Approved Design, Sufficiently Rigid To Retain Its Shape, And Constructed Either Of Metal Or Other Suitable Material Shod With Metal. Consolidation Shall Be Attained By The Use Of Suitable Vibrator Or Other Approved Equipment. In Operation, The Screed Shall Be Moved Forward On The Forms With A Combined Longitudinal And Transverse Shearing Motion, Moving Always In The Direction In Which The Work Is Progressing And So Manipulated That Neither End Is Raised From The Side Forms During The Striking Off Process. If Necessary, This Shall Be Repeated Until The Surface Is Of Uniform Texture, True To Grade And Cross-section, And Free From Porous Areas. 5. Floating After The Concrete Has Been Struck Off And Consolidated, It Shall Be Further Smoothed, Trued, And Consolidated By Means Of A Longitudinal Float, Either By Hand Or Mechanical Method. A. Hand Method. The Hand-operated Longitudinal Float Shall Be Not Less Than 365 Cm (12 Feet) In Length And 15 Cm (6 Inches) In Width, Properly Stiffened To Prevent Flexibility And Warping. The Longitudinal Float, Operated From Foot Bridges Resting On The Side Forms And Spanning But Not Touching The Concrete, Shall Be Worked With A Sawing Motion While Held In A Floating Position Parallel To The Road Center Line, And Moving Gradually From One Side Of The Pavement To The Other. Movement Ahead Along The Center Line Of The Pavement Shall Be In Successive Advances Of Not More Than One-half The Length Of The Float. Any Excess Water Or Soupy Material Shall Be Wasted Over The Side Forms On Each Pass. B. Mechanical Method. The Mechanical Longitudinal Float Shall Be Of A Design Approved By The Lgu Project Engineer, And Shall Be In Good Working Condition. The Tracks From Which The Float Operates Shall Be Accurately Adjusted To The Required Crown. The Float Shall Be Accurately Adjusted And Coordinated With The Adjustment Of The Transverse Finishing Machine So That A Small Amount Of Mortar Is Carried Ahead Of The Float At All Times. The Forward Screed Shall Be Adjusted So That The Float Will Lap The Distance Specified By The Lgu Project Engineer On Each Transverse Trip. The Float Shall Pass Over Each Areas Of Pavement At Least Two Times, But Excessive Operation Over A Given Area Will Not Be Permitted. Any Excess Water Or Soupy Material Shall Be Wasted Over The Side Forms On Each Pass. C. Alternative Mechanical Method. As An Alternative, The Contractor May Use A Machine Composed Of A Cutting And Smoothing Float Or Floats Suspended From And Guided By A Rigid Frame. The Frame Shall Be Carried By Four Or More Visible Wheels Riding On, And Constantly In Contact With The Side Forms. If Necessary, Following One Of The Preceding Method Of Floating, Long Handled Floats Having Blades Not Less Than 150 Cm (5 Feet) In Length And 15 Cm (6 Inches) In Width May Be Used To Smooth And Fill In Open-textured Areas In The Pavement. Long-handled Floats Shall Not Be Used To Float The Entire Surface Of The Pavement In Lieu Of, Or Supplementing, One Of The Preceding Methods Of Floating. When Strike Off And Consolidation Are Done By The Hand Method And The Crown Of The Pavement Will Not Permit The Use Of The Longitudinal Float, The Surface Shall Be Floated Transversely By Means Of The Long-handled Float. Care Shall Be Taken Not To Work The Crown Out Of The Pavement During The Operation. After Floating, Any Excess Water And Laitance Shall Be Removed From The Surface Of The Pavement By A 3-m Straight-edge Or More In Length. Successive Drags Shall Be Lapped One-half The Length Of The Blade. 6. Straight-edge Testing And Surface Correction After The Floating Has Been Completed And The Excess Water Removed, But While The Concrete Is Still Plastic, The Surface Of The Concrete Shall Be Tested For Trueness With A 300 Cm Long Straight-edge. For This Purpose, The Contractor Shall Furnish And Use An Accurate 300-cm Straight-edge Swung From Handles 100 Cm (3 Feet) Longer Than One-half The Width Of The Slab. The Straight-edge Shall Be Held In Contact With The Surface In Successive Positions Parallel To The Road Center Line And The Whole Area Gone Over From One Side Of The Slab To The Other As Necessary. Advances Along The Road Shall Be In Successive Stages Of Not More Than One-half The Length Of The Straight-edge. Any Depressions Found Shall Be Immediately Filled With Freshly Mixed Concrete, Struck Off, Consolidated And Refinished. High Areas Shall Be Cut Down And Refinished. Special Attention Shall Be Given To Assure That The Surface Across Joints Meets The Requirements For Smoothness. Straight-edge Testing And Surface Corrections Shall Continue Until The Entire Surface Is Found To Be Free From Observable Departures From The Straight-edge And The Slab Conforms To The Required Grade And Cross-section. 7. Final Finish If The Surface Texture Is Broom Finished, It Shall Applied When The Water Sheen Has Practically Disappeared. The Broom Shall Be Drawn From The Center To The Edge Of The Pavement With Adjacent Strokes Slightly Overlapping. The Brooming Operation Should Be So Executed That The Corrugations Produced In The Surface Shall Be Uniform In Appearance And Not More Than 1.5 Mm In Depth. Brooming Shall Be Completed Before The Concrete Is In Such Condition That The Surface Will Be Unduly Roughened By The Operation. The Surface Thus Finished Shall Be Free From Rough And Porous Areas, Irregularities, And Depressions Resulting From Improper Handling Of The Broom. Brooms Shall Be Of The Quality Size And Construction And Be Operated So As To Produce A Surface Finish Meeting The Approval Of The Lgu Project Engineer. Subject To Satisfactory Results Being Obtained And Approval Of The Lgu Project Engineer, The Contractor Will Be Permitted To Substitute Mechanical Brooming In Lieu Of The Manual Brooming Herein Described. If The Surface Texture Is Belt Finished, When Straight-edging Is Complete And Water Sheen Has Practically Disappeared And Just Before The Concrete Becomes Non-plastic, The Surface Shall Be Belted With 2-ply Canvass Belt Not Less Than 20 Cm Wide And At Least 100 Cm Longer Than The Pavement Width. Hand Belts Shall Have Suitable Handles To Permit Controlled, Uniform Manipulation. The Belt Shall Be Operated With Short Strokes Transverse To The Center Line And With A Rapid Advances Parallel To The Center Line. If The Surface Texture Is Drag Finished, A Drag Shall Be Used Which Consists Of A Seamless Strip Of Damp Burlap Or Cotton Fabric, Which Shall Produce A Uniform Of Gritty Texture After Dragging It Longitudinally Along The Full Width Of Pavement. For Pavement 5 M Or More In Width, The Drag Shall Be Mounted On A Bridge Which Travels On The Forms. The Dimensions Of The Drag Shall Be Such That A Strip Of Burlap Or Fabric At Least 100 Cm Wide Is In Contact With The Full Width Of Pavement Surface While The Drag Is Used. The Drag Shall Consist Of Not Less Than 2 Layers Of Burlap With The Bottom Layer Approximately 15 Cm Wider Than The Layer. The Drag Shall Be Maintained In Such Condition That The Resultant Surface Is Of Uniform Appearance And Reasonably Free From Grooves Over 1.5 Mm In Depth. Drag Shall Be Maintained Clean And Free From Encrusted Mortar. Drags That Cannot Be Cleaned Shall Be Discarded And New Drags Be Substituted. Regardless Of The Method Used For Final Finish, The Hardened Surface Of Pavement Shall Have A Coefficient Of Friction Of 0.25 Or More. Completed Pavement That Is Found To Have A Coefficient Of Friction Less Than 0.25 Shall Be Grounded Or Scored By The Contractor At His Expense To Provide The Required Coefficient Of Friction. 8. Edging At Forms And Joints After The Final Finish, But Before The Concrete Has Taken Its Initial Set, The Edges Of The Pavement Along Each Side Of Each Slab, And On Each Side Of Transverse Expansion Joints, Formed Joints, Transverse Construction Joints, And Emergency Construction Joints, Shall Be Worked With An Approved Tool And Rounded To The Radius Required By The Plans. A Well – Defined And Continuous Radius Shall Be Produced And A Smooth, Dense Mortar Finish Obtained. The Surface Of The Slab Shall Not Be Unduly Disturbed By Tilting The Tool During The Use. At All Joints, Any Tool Marks Appearing On The Slab Adjacent To The Joints Shall Be Eliminated By Brooming The Surface. In Doing This, The Rounding Of The Corner Of The Slab Shall Not Be Disturbed. All Concrete On Top Of The Joint Filler Shall Be Completely Removed. All Joints Shall Be Tested With A Straight-edge Before The Concrete Has Set And Correction Made If One Edge Of The Joint Is Higher Than The Other. 311.3.14 Surface Test As Soon As The Concrete Has Hardened Sufficiently, The Pavement Surface Shall Be Tested With A 3-m Straight-edge Or Other Specified Device. Areas Showing High Spots Of More Than 3 Mm But Not Exceeding 12 Mm In 3 M Shall Be Marked And Immediately Ground Down With An Approved Grinding Tool To An Elevation Where The Area Or Spot Will Not Show Surface Deviations In Excess Of 3 Mm When Tested With 3 M Straight-edge. Where The Departure From Correct Cross-section Exceeds 12 Mm, The Pavement Shall Be Removed And Replaced By And At The Expense Of The Contractor. Any Area Or Section So Removed Shall Be Not Less Than 1.5 M In Length And Not Less Than The Full Width Of The Lane Involved. When It Is Necessary To Remove And Replace A Section Of Pavement, Any Remaining Portion Of The Slab Adjacent To The Joints That Is Less Than 1.5 M In Length, Shall Also Be Removed And Replaced. 311.3.15 Curing Immediately After The Finishing Operations Have Been Completed And The Concrete Has Sufficiently Set, The Entire Surface Of The Newly Placed Concrete Shall Be Cured In Accordance With Either One Of The Methods Described Herein. Failure To Provide Sufficient Cover Material Of Whatever Kind The Contractor May Elect To Use, Or The Lack Of Water To Adequately Take Care Of Both Curing And Other Requirements, Shall Be A Cause For Immediate Suspension Of Concreting Operations. The Concrete Shall Not Be Left Exposed For More Than ½ Hour Between Stages Of Curing Or During The Curing Period. In All Congested Places, Concrete Works Should Be Designed So That The Designed Strength Is Attained. 1. Cotton Of Burlap Mats The Surface Of The Pavement Shall Be Entirely Covered With Mats. The Mats Used Shall Be Of Such Length (or Width) That As Laid They Will Extend At Least Twice The Thickness Of The Pavement Beyond The Edges Of The Slab. The Mat Shall Be Placed So That The Entire Surface And The Edges Of The Slab Are Completely Covered. Prior To Being Placed, The Mats Shall Be Saturated Thoroughly With Water. The Mat Shall Be So Placed And Weighted Down So As To Cause Them To Remain In Intimate Contact With The Covered Surface. The Mat Shall Be Maintained Fully Wetted And In Position For 72 Hours After The Concrete Has Been Placed Unless Otherwise Specified. 2. Waterproof Paper The Top Surface And Sides Of The Pavement Shall Be Entirely Covered With Waterproof Paper, The Units Shall Be Lapped At Least 45 Cm. The Paper Shall Be So Placed And Weighted Down So As To Cause It To Remain In Intimate Contact With The Surface Covered. The Paper Shall Have Such Dimension But Each Unit As Laid Will Extend Beyond The Edges Of The Slab At Least Twice The Thickness Of The Pavement, Or At Pavement Width And 60 Cm Strips Of Paper For The Edges. If Laid Longitudinally, Paper Not Manufactured In Sizes Which Will Provide This Width Shall Be Securely Sewed Or Cemented Together, The Joints Being Securely Sealed In Such A Manner That They Do Not Open Up Or Separate During The Curing Period. Unless Otherwise Specified, The Covering Shall Be Maintained In Place For 72 Hours After The Concrete Has Been Placed. The Surface Of The Pavement Shall Be Thoroughly Wetted Prior To The Placing Of The Paper. 3. Straw Curing When This Type Of Curing Is Used, The Pavement Shall Be Cured Initially With Burlap Or Cotton Mats, Until After Final Set Of The Concrete Or, In Any Case, For 12 Hours After Placing The Concrete. As Soon As The Mats Are Removed, The Surface And Sides Of The Pavement Shall Be Thoroughly Wetted And Covered With At Least 20 Cm Of Straw Or Hay, Thickness Of Which Is To Be Measured After Wetting. If The Straw Or Hay Covering Becomes Displaced During The Curing Period, It Shall Be Replaced To The Original Depth And Saturated. It Shall Be Kept Thoroughly Saturated With Water For 72 Hours And Thoroughly Wetted Down During The Morning Of The Fourth Day, And The Cover Shall Remain In Place Until The Concrete Has Attained The Required Strength. 4. Impervious Membrane Method The Entire Surface Of The Pavement Shall Be Sprayed Uniformly With White Pigmented Curing Compound Immediately After The Finishing Of The Surface And Before The Set Of The Concrete Has Taken Place, Or If The Pavement Is Cured Initially With Jute Or Cotton Mats, It May Be Applied Upon Removal Of The Mass. The Curing Compound Shall Not Be Applied During Rain. Curing Compound Shall Be Applied Under Pressure At The Rate 4 L To Not More Than 14 M2 By Mechanical Sprayers. The Spraying Equipment Shall Be Equipped With A Wind Guard. At The Time Of Use, The Compound Shall Be In A Thoroughly Mixed Condition With The Pigment Uniformly Dispersed Throughout The Vehicle. During Application, The Compound Shall Be Stirred Continuously By Effective Mechanical Means. Hand Spraying Of Odd Widths Or Shapes And Concrete Surface Exposed By The Removal Of Forms Will Be Permitted. Curing Compound Shall Not Be Applied To The Inside Faces Of Joints To Be Sealed, But Approved Means Shall Be Used To Insure Proper Curing At Least 72 Hours And To Prevent The Intrusion Of Foreign Material Into The Joint Before Sealing Has Been Completed. The Curing Compound Shall Be Of Such Character That The Film Will Harden Within 30 Minutes After Application. Should The Film Be Damaged From Any Cause Within The 72 Hour Curing Period, The Damaged Portions Shall Be Repaired Immediately With Additional Compound. 5. White Polyethylene Sheet The Top Surface And Sides Of The Pavement Shall Be Entirely Covered With Polyethylene Sheeting. The Units Used Shall Be Lapped At Least 45 Cm. The Sheeting Shall Be So Placed And Weighted Down So As To Cause It To Remain Intimate Contact With The Surface Covered. The Sheeting As Prepared For Use Shall Have Such Dimension That Each Unit As Laid Will Extend Beyond The Edges Of The Slab At Least Twice The Thickness Of The Pavement. Unless Otherwise Specified, The Covering Shall Be Maintained In Place For 72 Hours After The Concrete Has Been Placed. 311.3.16 Removal Of Forms After Forms For Concrete Shall Remain In Place Undisturbed For Not Less Than Twenty Four (24) Hours After Concrete Pouring. In The Removal Of Forms, Crowbars Should Be Used In Pulling Out Nails And Pins. Care Should Be Taken So As Not To Break The Edges Of The Pavement. In Case Portions Of The Concrete Are Spalled, They Shall Be Immediately Repaired With Fresh Mortar Mixed In The Proportion Of One Part Of Portland Cement And Two Parts Fine Aggregates. Major Honeycomb Areas Will Be Considered As Defective Work And Shall Be Removed And Replaced At The Expense Of The Contractor. Any Area Or Section So Removed Shall Not Be Less Than The Distance Between Weakened Plane Joint Nor Less Than The Full Width Of The Lane Involved. 311.3.17 Sealing Joints Joints Shall Be Sealed With Asphalt Sealant Soon After Completion Of The Curing Period And Before The Pavement Is Opened To Traffic, Including The Contractor’s Equipment. Just Prior To Sealing, Each Joint Shall Be Thoroughly Cleaned Of All Foreign Materials Including Membrane Curing Compound And The Joint Faces Shall Be Clean And Surface Dry When The Seal Is Applied. The Sealing Material Shall Be Applied To Each Joint Opening To Conform To The Details Shown On The Plans Or As Directed By The Lgu Project Engineer. Material For Seal Applied Hot Shall Be Stirred During Heating So That Localized Overheating Does Not Occur. The Pouring Shall Be Done In Such A Manner That The Material Will Not Be Spilled On The Exposed Surfaces Of The Concrete. The Use Of Sand Or Similar Material As A Cover For The Seal Will Not Be Permitted. Preformed Elastomeric Gaskets For Sealing Joints Shall Be Of The Cross-sectional Dimensions Shown On The Plans. Seals Shall Be Installed By Suitable Tools, Without Elongation And Secured In Placed With An Approved Lubricant Adhesive Which Shall Cover Both Sides Of The Concrete Joints. The Seals Shall Be Installed In A Compressive Condition And Shall At Time Of Placement Be Below The Level Of The Pavement Surface By Approximately 6 Mm. The Seals Shall Be In One Piece For The Full Width Of Each Transverse Joint. 311.3.18 Protection Of Pavement The Contractor Shall Protect The Pavement And Its Appurtenances Against Both Public Traffic And Traffic Caused By His Own Employees And Agents. This Shall Include Watchmen To Direct Traffic And The Erection Of And Maintenance Of Warning Signs, Lights, Pavement Bridges Or Cross-overs, Etc. The Plans Or Special Provisions Will Indicate The Location And Type Of Device Or Facility Required To Protect The Work And Provide Adequately For Traffic. All Boreholes After Thickness And/or Strength Determinations Of Newly Constructed Asphalt And Concrete Pavements Shall Be Immediately Filled/restored With The Prescribed Concrete/asphalt Mix After Completion Of The Drilling Works. Any Damage To The Pavement, Occurring Prior To Final Acceptance, Shall Be Repaired Or The Pavement Be Replaced. 311.3.19 Concrete Pavement – Slip Form Method If The Contract Calls For The Construction Of Pavement Without The Use Of Fixed Forms, The Following Provisions Shall Apply: 1. Grade After The Grade Or Base Has Been Placed And Compacted To The Required Density, The Areas Which Will Support The Paving Machine Shall Be Cut To The Proper Elevation By Means Of A Properly Designed Machine. The Grade On Which The Pavement Is To Be Constructed Shall Then Be Brought To The Proper Profile By Means Of Properly Designed Machine. If The Density Of The Base Is Disturbed By The Grading Operation, It Shall Be Corrected By Additional Compaction Before Concrete Is Placed. The Grade Should Be Constructed Sufficiently In Advance Of The Placing Of The Concrete. If Any Traffic Is Allowed To Use The Prepared Grade, The Grade Shall Be Checked And Corrected Immediately Before The Placing Of Concrete. 2. Placing Concrete The Concrete Shall Be Placed With An Approved Slip-form Paver Designed To Spread, Consolidate, Screed And Float-finish The Freshly Placed Concrete In One Complete Pass Of The Machine In Such A Manner That A Minimum Of Hand Finish Will Be Necessary To Provide A Dense And Homogenous Pavement In Conformance With The Plans And Specifications. The Machine Shall Vibrate The Concrete For The Full Width And Depth Of The Strip Of Pavement Being Placed. Such Vibration Shall Be Accompanied With Vibrating Tubes Or Arms Working In The Concrete Or With A Vibrating Screed Or Pan Operating On The Surface Of The Concrete. The Sliding Forms Shall Be Rigidly Held Together Laterally To Prevent Spreading Of The Forms. The Forms Shall Trail Behind The Paver For Such A Distance That No Appreciable Slumping Of The Concrete Will Occur, And That Necessary Final Finishing Can Be Accomplished While The Concrete Is Still Within The Forms. Any Edge Slump Of The Pavement, Exclusive Of Edge Rounding, In Excess Of 6 Mm Shall Be Corrected Before The Concrete Has Hardened. The Concrete Shall Be Held At A Uniform Consistency, Having A Slump Of Not More Than 40 Mm (1-12/ Inches). The Slip Form Paver Shall Be Operated With As Nearly As Possible A Continuous Forward Movement And That All Operations Of Mixing, Delivering And Spreading Concrete Shall Be Coordinated So As To Provide Uniform Progress With Stopping And Starting Of The Paver Held To A Minimum. If, For Any Reason, It Is Necessary To Stop The Forward Movement Of The Paver The Vibratory And Tamping Elements Shall Also Be Stopped Immediately. No Tractive Force Shall Be Applied To The Machine, Except That Which Is Controlled From The Machine. 3. Finishing The Surface Smoothness And Texture Shall Meet The Requirements Of Subsections 311.3.13 And 311.3.14. 4. Curing Unless Otherwise Specified, Curing Shall Be Done In Accordance With One Of The Methods Included In Subsection 311.3.15. The Curing Media Shall Be Applied At The Appropriate Time And Shall Be Applied Uniformly And Completely To All Surfaces And Edges Of The Pavement. 5. Joints All Joints Shall Be Constructed In Accordance With Subsection 311.3.12. 6. Protection Against Rain In Order That The Concrete May Be Properly Protected Against Rain Before The Concrete Is Sufficiently Hardened, The Contractor Will Be Required To Have Available At All Times, Materials For The Protection Of The Edges And Surface Of The Unhardened Concrete. Such Protective Materials Shall Consist Of Standard Metal Forms Or Wood Planks Having A Nominal Thickness Of Not Less Than 50 Mm (2 Inches) And A Nominal Width Of Not Less Than The Thickness Of The Pavement At Its Edge For The Protection Of The Pavement Edges, And Covering Material Such As Burlap Or Cotton Mats, Curing Paper Or Plastic Sheeting Materials For The Protection Of The Surface Of The Pavement. When Rain Appears Imminent, All Paving Operations Shall Stop And All Available Personnel Shall Begin Placing Forms Against The Sides Of The Pavement And Covering The Surface Of The Unhardened Concrete With The Protective Covering. 311.3.22 Acceptance Of Concrete The Strength Level Of The Concrete Will Be Considered Satisfactory If The Averages Of All Sets Of Three (3) Consecutive Strength Test Results Equal Or Exceed The Specified Strength, Fc’ And No Individual Strength Test Result Is Deficient By More Than 15% Of The Specified Strength, Fc’. Concrete Deemed To Be Not Acceptable Using The Above Criteria May Be Rejected Unless The Contractor Can Provide Evidence, By Means Of Core Tests, That The Quality Of Concrete Represented By Failed Test Results Is Acceptable In Place. At Least Three (3) Representative Cores Shall Be Taken From Each Member Or Area Of Concrete In Place That Is Considered Deficient. The Location Of Cores Shall Be Determined By The Engineer So That There Will Be At Least Impairment Of Strength Of The Structure. The Obtaining And Testing Of Drilled Cores Shall Be In Accordance With Aashto T 24. Concrete In The Area Represented By The Cores Will Be Considered Adequate If The Average Strength Of The Cores Is Equal To At Least 85% Of, And If No Single Core Is Less Than 75% Of, The Specified Strength, Fc’. If The Strength Of Control Specimens Does Not Meet The Requirements Of This Subsection, And It Is Not Feasible Or Not Advisable To Obtain Cores From The Structure Due To Structural Considerations, Payment Of The Concrete Will Be Made At An Adjusted Price Due To Strength Deficiency Of Concrete Specimens As Specified Hereunder: Deficiency In Strength Of Concrete Specimens, Percent (%) Percent (%) Of Contract Price Allowed Less Than 5 100 5 To Less Than 10 80 10 To Less Than 15 70 15 To Less Than 20 60 20 To Less Than 25 50 25 Or More 0 311.3.23 Opening To Traffic The Engineer Will Decide When The Pavement May Be Opened To Traffic. The Road Will Not Be Opened To Traffic Until Test Specimens Molded And Cured In Accordance With Aashto T 23 Have Attained The Minimum Strength Requirements In Subsection 311.2.11. If Such Tests Are Not Conducted Prior To The Specified Age The Pavement Shall Not Be Operated To Traffic Until 14 Days After The Concrete Was Placed. Before Opening To Traffic, The Pavement Shall Be Cleaned And Joint Sealing Completed. 311.3.24 Tolerance And Pavement Thickness 1. General The Thickness Of The Pavement Will Be Determined By Measurement Of Cores From The Completed Pavement In Accordance With Aashto T 148. The Completed Pavement Shall Be Accepted On A Lot Basis. A Lot Shall Be Considered As 1000 Linear Meters Of Pavement When A Single Traffic Lane Is Poured Or 500 Linear Meters When Two Lanes Are Poured Concurrently. The Last Unit In Each Slab Constitutes A Lot In Itself When Its Length Is At Least ½ Of The Normal Lot Length. If The Length Of The Last Unit Is Shorter Than ½ Of The Normal Lot Length, It Shall Be Included In The Previous Lot. Other Areas Such As Intersections, Entrances, Crossovers, Ramp, Etc., Will Be Grouped Together To Form A Lot. Small Irregular Areas May Be Included With Other Unit Areas To Form A Lot. Each Lot Will Be Divided Into Five (5) Equal Segments And One Core Will Be Obtained From Each Segment In Accordance With Aashto T 24. 2. Pavement Thickness It Is The Intent Of This Specification That The Pavement Has A Uniform Thickness As Called For On The Plans For The Average Of Each Lot As Defined. After The Pavement Has Met All Surface Smoothness Requirements, Cores For Thickness Measurements Will Be Taken. In Calculating The Average Thickness Of The Pavement, Individual Measurements Which Are In Excess Of The Specified Thickness By More Than 5 Mm Will Be Considered As The Specified Thickness Plus 5 Mm And Measurement Which Are Less Than The Specified Thickness By More Than 25 Mm Shall Not Be Included In The Average. When The Average Thickness For The Lot Is Deficient, The Contract Unit Price Will Be Adjusted For Thickness In Accordance With Paragraph (3 Below). Individual Areas Within A Segment Found Deficient In Thickness By More Than 25 Mm Shall Be Evaluated By The Lgu Project Engineer, And If In His Judgment, The Deficient Areas Warrant Removal, They Shall Be Removed And Replaced By The Contractor With Pavement Of The Specified Thickness At His Entire Expense. However, If The Evaluation Of The Lgu Project Engineer Is That The Deficient Area Should Not Be Removed And Replaced, Such Area Will Not Be Paid. When The Measurement Of Any Core Is Less Than The Specified Thickness By More Than 25 Mm, The Actual Thickness Of The Pavement In This Area Will Be Determined By Taking Additional Cores At No Less Than 5 M Intervals Parallel To The Center Line In Each Direction From The Affected Location Until A Core Is Found In Each Direction, Which Is Not Deficient In Thickness By More Than 25 Mm. The Area Of Slab For Which No Payment Will Be Made Shall Be The Product Of The Paving Width Multiplied By The Distance Along The Center Line Of The Road Between Transverse Sections Found Not Deficient In Thickness By More Than 25 Mm. The Thickness Of The Remainder Of The Segment To Be Used To Get The Average Thickness Of Each Lot Shall Be Determined By Taking The Average Thickness Of Additional Cores Which Are Not Deficient By More Than 25 Mm. 3. Adjustment For Thickness When The Average Thickness Of The Pavement Per Lot Is Deficient, Payment For The Lot Shall Be Adjusted As Follows: Deficiency In The Average Thickness Per Lot (mm) Percent (%) Of Contract Price Per Lot 0 – 5 100% Payment 6 – 10 95% Payment 11 – 15 85% Payment 16 – 20 70% Payment 21 – 25 50% Payment More Than 25 Remove And Replace/ No Payment No Acceptance And Final Payment Shall Be Made On Completed Pavement Unless Core Test For Thickness Determination Is Conducted 311.4 Environmental Measures In Loading Cement To The Truck And Unloading It To The Temporary Bodega, And From The Bodega To Batching Plant And During Concrete Work Operation Workers Doing This Job Shall Be Provided With Gears So As To Avoid Inhaling Cement Dust Particles That Could Affect Their Health. Workers In Construction Site Shall Be Provided With Working Gloves, Mask Boots And Clothing To Prevent Workers From Being Contaminated With Concrete Mix. The Contractor Shall See To It That The Noise Level Of The Exhaust Mufflers Of The Equipment Shall Be At The Minimum. Otherwise, The Contractor Must Replace All The Exhaust Mufflers Of The Equipment With A New One And Or Provide Muffler Silencers. All Roads Leading The Construction Site And Batching Plant Shall Be Moist During The Entire Works Operation To Prevent The Blowing Up Of Dust Particles. During Work Operation, Precautionary Signboards Shall Be Provided By The Contractor To Prevent Accidents And Damage To The Freshly Laid Concrete.

Details: Description Invitation To Bid Project No: 005 – 2025 1. The Department Of Education Through The Fy 2024 Gaa Intends To Apply The Sum Of Seven Million Three Hundred Thirty-eight Thousand Five Hundred Seven And 00/100 (7,338,507.00) Being The Approved Budget For The Contract (abc) Described Below For The Procurement Of Assistive Devices, Equipment, Supplies And Materials For Inclusive Learning Resource Centers. Bids Received In Excess Of Abc Shall Be Automatically Rejected At The Bid Opening. Unit Description Qty Cost Abc (vat Inclusive) 1 Lot Procurement Of Assistive Devices, Equipment, Supplies And Materials For Inclusive Learning Resource Centers 1 1 Unit Learners'/clients' Chart Materials A4 Size 8-1/4 X 11-3/4 Inches Or 210 X 297 Mm Or 29.7 X 21 Cm Laminated Full Color High Quality Print Photopaper 10 70.00 700.00 2 Set Anatomical Model-human Torso Model Size: 1/2 Life Size Material: Pvc, Includes: Stand 1 62,918.00 62,918.00 3 Unit Blood Pressure-blood Pressure Monitor Type: Upper-arm Monitor Type: Digital Cuff Size: 32cm Dimension (w X H X D): 145 X 466 X 145mm Weight: 250g Power Supply: Battery Type: Li-polymer Smart App Availability: Yes, Automatic Shut Off: Wi-fi: No 5 6,560.00 32,800.00 4 Unit Stethoscope: Dual Tube Stethoscope Weight: 185g, Length: 80cm Product Material: Polymer Diaphragm, Listener Material: High-density Stainless Steel Product Composition: Eartip, Ear Hooks, Leaf Spring, Hose Heads, Diaphragms 2 1,380.00 2,760.00 5 Piece Tape Measure-material: Pvc It Has Centimeter Scale On Reverse Side Which Is Up To 300cm Large, Easy To Read Marking Measures Up To 120 Inches 10 300.00 3,000.00 6 Piece Hand Dynamometer - Hand Dynamometer Type: Electronic Counting Gripper Function: Comprehensive Fitness Exercise Material: Abs Size: 15cm/5.90""x10.5cm/4.13""x2cm/0.79"" 10 1,900.00 19,000.00 7 Packs Ice Massage Caps- Size: 2 Count (pack Of 1) Measuring 2.9” In Diameter, The Ice Cup Massager Holder Also Fits Comfortably In The Hand. Material: Polyethylene 10 700.00 7,000.00 8 Unit Balance Board- Balance Board Type: Rocker Board Dimensions: 32.28 X 11.81 X 0.59 Inches Weight Capacity: 100 Kg Material: Beech Wood Anti-skid Feature: Not Specified 5 3,700.00 18,500.00 9 Unit Treatment Table- Top Shelf With Guard Rail And Formica Material. Down Shelf, Material Plain Sheet. Mounted On 4 Swivel Caster Rubber Wheels 2″ With 2 Pieces Lock. Size: Lxwxh (28″x20″x34.5″) Painted White 1 17,400.00 17,400.00 10 Unit Exercise Steps-aerobic Step Board 69 X 28 X 15cm. Dimension: 69 X 28 X 15cm Length: 27" Width: 10.5" Adjustable Height Up To 10cm To 15cm. Offers A Secure, Nonslip Surface For Your Workout Routine, Nonskid, Feet Provide Stability & Protect Floors. 5 1,934.00 9,670.00 11 Pair Pediatric Examination Gowns- Assorted For Kids And Adult Pediatric Examination Gowns Opening: Full Open Back. Style: Child Size Color: Jellybean Print. Made With High Quality, 100% Cotton Comfortable, Durable, Washable, And Reusable Hook And Loop Closures At Neck And Mid-back. 10 700.00 7,000.00 12 Piece Towels- Material: High Quality 100% Cotton Terry. 500gm2. Size: 90 X 180cm. 20 300.00 6,000.00 13 Piece Bed Sheets- Material: Cotton + Polyester, Packaging Content: 2 Pcs Pillowcase, 1 Pc Fitted Sheet, Single Size:36"*75"+7.8", Pillowcase Size: 18'*28", Garterized Corners 20 2,000.00 40,000.00 14 Piece Pillows- Pillows, Plain White, Soft Pillow, Size:18x28 Inches 10 900.00 9,000.00 15 Piece Pillowcase- Length: 50 Cm (20 ") Pillowcase Quantity: 1 Piece Width: 80 Cm (31 ") 100 % Polyester 20 180.00 3,600.00 16 Piece Blankets- Length: 160 Cm White Sheet Soft Texture, High Quality Fabric Size: 52 X 90 Inch 20 450.00 9,000.00 17 Unit Step Stools - Step Stools Double Steel Caravan Step. Rubber Non- Slip Steps. Leg Distance Front To Back 65 Cm. Width 42 Cm. Top Step Height 38 Cm. Bottom Step 20 Cm. 5 3,600.00 18,000.00 18 Unit Therapist Stools On Wheels-adjustable Height Of 19 - 24". It Comes With A 3" Hi-density Cushion With Multi-layered Padding, And A 14" Seat Diameter. Built With 5 Casters Made Of Plastic Easy To Clean. Color: Black 5 4,950.00 24,750.00 19 Piece Kinesiology Tape-ultra-strong And Sticky-hypoallergenic Adhesive Water Resistant. 97% Cotton, 3% Nylon. 180% Stretch For Full Range Of Motion Latex And Zinc Free Sticks 2-7 Days 5-10 Applications Per Roll Each Is 2""x 16.4"" (5cmx5cm) 20 2,100.00 42,000.00 20 Set Splinting Materials - Rescue Padded Board Splint. 6 Paddes Wood Splint (different Sizes) Sizes: 35"", 25"" And 15". Velcro Straps Color: Blue. 20 4,200.00 84,000.00 21 Unit Paraffin Bath- Large Opening Design: Inner Pot Allows For Hands, Feet, And Elbows To Be Dipped Into The Melted Wax. Alloy Heating Pot Melts Paraffin Wax Blocks In 0.5 Hours. Adjustable Heating Ranges From 86-158°f. Timer: Settable From 1 To 99 Minutes. (free Installation) 2 32,340.00 64,680.00 22 Set Dumbbells Sets- Weight: 37kg Type: Medical Rehabilitation Equipment Total 18 Dumbbells 1 Lb / Piece, 2 Pieces 2 Lbs / Piece, 4 Pieces 3 Lbs / Piece, 4 Pieces 4 Lbs / Piece, 4 Pieces 5 Lbs / Piece, 4 Pieces 3 25,000.00 75,000.00 23 Set Goniometers- Protractor Goniometer With 360 Degrees Coverage To Measure Joint And Compare The Changes In Joint Angles Material: Clear Plastic 3 Goniometer: 12-inch, 8 Inch And 6 Inch 3 600.00 1,800.00 24 Set Reflex Hammer-features: Pointed Babinski-style Tip Zinc Alloy Comfortable Handle Grip Control, Hammer For High Elastic Pvc Rubber Material: Zinc Alloy + Pvc; Color: Black Package Size: 27*11*3.5cm/10.6*4.3*1.3-inch Package Weight: 140g/4.9oz. 1 8,100.00 8,100.00 25 Piece Thermometer - Body Temperature Measurement: 34.0-42.9°c / 93.2-109.2°f. Material: Abs Plastic. Accuracy: (+/-)0.2°c. Auto-shutdown Time: About 18s Power Supply: 2 * 1.5v Aaa Batteries (not Included). 1 Year Warranty 5 1,600.00 8,000.00 26 Unit Multiple Mode Electrical Stimulator-1 Second Measuring Time. 3 Color Backlight Fever Reminders Auto Shut Off At 18 Seconds Store 50 Sets Of Data. Body Temperature Measurement: 34.0-42.9°c / 93.2-109.2°f. 3 9,884.00 29,652.00 27 Piece Foam Rolls- Material: Expanded Polypropylene Foam Item Weight: 0.42 Pounds Size: 18 Inches 3 4,000.00 12,000.00 28 Piece Mobilization Belts And Devices- Size 8 Feet Specific Uses For Product. Use For Legs, Hips, Arms, Back, Whole Body - High-quality Nylon Mobilization Belt Features A Plastic Side-release Buckle And Is Designed For Durability And Patient Safety. 5 2,850.00 14,250.00 29 Piece Gait Belt-1x Transfer Gait Belt Measurement Length: 60 Inches Width: 2 Inches 5 1,458.00 7,290.00 30 Set Theraband -4 Resistance Levels, Including Yellow, Red, Green, And Blue Supplied In Lay Flat Length Of 8", 12" And 18" Latex Rubber Weight Level: Yellow: 3 Lbs-4.3 Lbs Red: 3.7 Lbs-5.5 Lbs Green: 4.6 Lbs-6.7 Lbs Blue: 5.8 Lbs-8.6 Lbs 5 10,100.00 50,500.00 31 Piece Wedge Bolsters- A Firm And Breathable Bed Wedge Pillow Stays Cool, And Its Measurements Are 25″l X 25″w X 12″h Inches. / Breathable & Washable Cover / Designed To Provide Higher Body Support. 5 6,998.00 34,990.00 32 Piece Round Bolsters-weight：0-0.5 Kg Shape：column Feature：memory Filling：microfiber Material：100% Fiber Size:8" X 36" Color：white - Ideal For Hugging, Cylindrical Pillow, Great For Side Sleepers. 5 4,800.00 24,000.00 33 Piece Core Peak Bolsters- An All-purpose Positioning Aid • Provides Support Under The Legs, Arms, Feet, And Other Areas Of The Body. Fits Standard Treatment Tables • 18" In Length With At Least 6" In Diameter. 5 9,006.00 45,030.00 34 Piece Round Bolsters-weight：0-0.5 Kg Shape：column Feature：memory Filling：microfiber Material：100% Fiber Size:8" X 36" Color：white - Ideal For Hugging, Cylindrical Pillow, Great For Side Sleepers. 5 1,500.00 7,500.00 35 Piece Core Peak Bolsters- An All-purpose Positioning Aid • Provides Support Under The Legs, Arms, Feet, And Other Areas Of The Body. Fits Standard Treatment Tables • 18" In Length With At Least 6" In Diameter. 4 1,100.00 4,400.00 36 Piece Walking Cane-adjustable Aluminum Cane With Wooden Handle, Anodized Finish And Rubber Tip. The Tube Has A Spring Lock Pin For Adjusting Handle Height From 58-94 Cm. 5 1,320.00 6,600.00 37 Piece Quad Cane -stable Structure, Thickened Stainless Steel Material. Abs Non-slip Handle, Ergonomic Design, Comfortable Grip. Spring Button For Easy Height Adjustment. Firm Lock Hoops To Stabilize The Body. 4 2,740.00 10,960.00 38 Piece Wheelchair - Front Wheel Size: 6 Inches Expanded Size: 82 * 58 * 87cmseat Depth: 38cmrear Wheel Size: 16 Inches Back Height: 42cmfolded Size: 70 * 25 * 72cmhandrail Spacing: 55cmseat Width: 45cmnet Weight: 11kgnet Weight Of All Aluminum Alloy Frame: 11kg 10 5,600.00 56,000.00 39 Piece Pediatric Walker- Height-adjustable Frame Sizes. 360-degree Swivel Front Casters For Versatile And Flexible Mobility. Foot-operating Locking Mechanism On Front Casters. Rubber Tire Design 5 13,200.00 66,000.00 40 Set Communication Boards. Measures 9"x7.5". Binder Comes With 5 Different Colorful 10 Mil Poly Dividers, 3 Hard Strips (hook) Attached On Each Side To Hold 30 Cards. Each Card Measures 1.5 X 1.5. Inch Mounted With 1/2-inch Soft Dot (loop), And Round Corner Cut. 10 6,172.00 61,720.00 41 Set Dry Erase Sleeves. Reusable Dry Erase Pockets. Colors: Blue, Pink, Yellow, Red, Green, Purple. Size: 25.5*35.5cm(1pcs). Quantity: 12pcs Package Including: 6 X Dry Erase Pockets 6 Pens 10 796.00 7,960.00 42 Set Wind Up Toys. Category: Clockwork Engineering Road Roller Material: Plastic Size: 9.9*6.5*5.3(cm) Color: Three-color Random Hair Ages: 3+ 10 440.00 4,400.00 43 Set Wordless Picture Books. A Wordless Book About Dealing With Big Emotions Like Fear, Grief, Loss, Sadness, And Anger Hardcover | 36 Pages Product Dimension: Approx. W1cm X L22.2cm X H22.2cm Product Weight: Approx. .28kg 10 1,998.00 19,980.00 44 Piece File Folders. (black Or White) Model: Minimum Of 100 Pages Capacity Size: 310*235mm Suitable For School And Office Supply 10 280.00 2,800.00 45 Set Articulation Cards. Genre: Children's Learning & Education Sub-genre: Society & Culture Label: Scholastic Teaching Resources Language: English Publisher: Scholastic Teaching Resources 10 3,913.00 39,130.00 46 Set Basic Vocabulary Board. Each Unit Comes With: Flashcards Smash Mat Trace And Color Cut And Glue Flipbook Black And White Versions Of All Activities 10 10,150.00 101,500.00 47 Set Phonics Phones. Specifications - Each Pack Includes Two Durable Whisper Phones, One In Vibrant Blue And One In Eye-catching Red. 10 536.00 5,360.00 48 Piece Taekwondo Mats. Thickened 1 Meter X 1 Meter X 2 Cm Interlocking Mats. Color Blue. 30 1,750.00 52,500.00 49 Set Vestibular Balls- (3 Pieces) Material: Synthetic Material Size: 55.0 / 65.0 / 75.0 Cm. Weight: 1100.0 / 1400.0 / 1700.0 G. Color: Violet / Blue / Black 3 6,200.00 18,600.00 50 Unit Monkey Bar With Platform For Swing- Materials: 7/8-inch Plywood 3.5’x2, Washable Mat, 1/2-inch Braided Ropes, Stainless Steel Carabiners Dimensions: 47 X 27.5 Inches; Maximum Rope Length - 7 Feet, Weight Limit: 100 Kilos (free Installation) 1 42,000.00 42,000.00 51 Set Trampoline With Handrails 40-inch Jumping Surface Area, Handrail Adjusts From 28.5"" To 36.5""h 16lbs. Holds Up To 300 Lbs 2 11,580.00 23,160.00 52 Unit Tumble Barrels-inside Diameter: 18"-24”, Outside Diameter: 24", Weight: 250lbs. (free Installation) 1 40,695.00 40,695.00 53 Set Wall Bars- 6-hole Design Pull Up Bar. The Maximum Weight Is 200kg. Solid Steel Bar With Black Powder Coating To Prevent Rust And Corrosion And Prolong Service Life, With Soft Cushions. 2 2,598.00 5,196.00 54 Set Adl Board - 6 Colors, 6 Different Dressing Skills Training. A Quiet Skill Book Made Of Cardboard And Non- Woven Fabric. Suitable For Children 2-7 Years Old. Package Dimensions: 11.73 X 9.76 X 2.28 Inches Item Weight: 1.28 Pounds" 10 494.00 4,940.00 55 Unit Pediatric Walker - 360-degree Swivel Front Casters For Versatile And Flexible Mobility. Total Height: 75-90cm Side Wheel Width: 70cm. Front And Rear Track Width: 75cm. Left And Right Wheel Track: 40cm Suitable Height: 85-120cm. Weight: About 12kg 4 17,998.00 71,992.00 56 Set Assessment Tool Set Of Assessment Tools For Behavioral, Psychological, Intellectual, Motor, Socio- Emotional (1 Copies Per Set) Like: Ravens Progressive Matrices Tests, Goodenough-draw A Person Test 2 48,000.00 96,000.00 57 Set Assessment Tool Set Of Assessment Tools For Behavioral, Psychological, Intellectual, Motor, Socio- Emotional (1 Copies Per Set) Like: Wechsler Intelligence Scales For Children (wisc-v) 2 48,000.00 96,000.00 58 Pcs Reading Stand - High-grade Steel (iron). Color: Black. Dimensions: 26 Cm X 21 Cm X 16 Cm (folded) Adjustability: Multiple Notches For Adjustable Height And Angle. 1 Rotary Page Clip To Hold Pages Securely. 10 1,050.00 10,500.00 59 Unit Braille Translator- Supports Translation Of Print (word, Html, Daisy And Others) To Braille For Over 130 Languages. Drives All Major Braille Embossers. (with 6 Months Warranty) 1 136,800.00 136,800.00 60 Unit Laptop 15.5" – 17" Monitor, Processor: Between 2.0- 2.8ghz 512gb Ssd, 8gb Ram (3 Mos. Warranty) 36 39,000.00 1,404,000.00 61 Cord Hdmi Cord 5 Meters 5 600.00 3,000.00 62 Cord Hdmi Cord 10 Meters 5 900.00 4,500.00 63 Set Connector Cord. Cord With Male Plug To Connect From Cellphone/ Laptop To Sound Systems Microphone Port. 5 500.00 2,500.00 64 Unit Augmentative Communication Systems. Package Dimensions 9.13 X 3.03 X 1.1 Inches Batteries 2 Aaa Batteries Required. (included) Preprogrammed Commands Wide Variety- Travel Bag- Aac Device 10 3,702.00 37,020.00 65 Unit Call Lights. Receiver Working Voltage: 110-260v Transmitter Battery: 12v 23a Alkaline Battery Working Distance: 1000 Feet In Open Area. [packing List]. 3 Receivers 2 Transmitters. 2 X Double-sided Tape. 1 X User Manual. 2 X 12v 23a Batteries. 10 1,536.00 15,360.00 66 Unit External Hard Drive. 1tb External Hard Drive Usb 3.0 5 3,500.00 17,500.00 67 Unit Audio Voice Recorder. Built-in 375mah Battery, Specification: Recording Time: 512kbps， 32gb: About 144 Hours. Storage Media: Tf Card, 32gb, Battery Capacity: 375mah, Package Size: 15.2x7.8x3.7cm/5.9x3x1.4in, Package Weight: 135g – 140g/4.7oz 10 2,674.00 26,740.00 68 Unit Portable Reading Camera -macro Focus Range 10 Cm Shooting Modes Easy, Macro, Automatic Exposure Control Type Automatic Color; White Video Capture Resolution; 1080p, 2448p 5 10,260.00 51,300.00 69 Unit Laser Printer. Computer Printers Using Powder - Based For Swell Paper. 2 20,000.00 40,000.00 70 Unit 3 In Printer - Print, Scan, Copy, Fax With Adf, Flatbed Color Image Scanner, A4, Ltr, 8.5 X 13’, Folio 9 19,080.00 171,720.00 71 Unit Projector -5,000 Ansi Lumens (standard). Wxga 1,280 X 800) Dlp Type Projector. With Built-in Speaker X 16,000 Hours (standard), 10,000 Hours (eco), 15,000 Hours (extreme Eco) Lamp Life Wireless Projection Hdmi Cable, Bag 2 Years Warranty" 1 25,000.00 25,000.00 72 Unit Projection Screen. Specs: 120 Inch Projector Screen With Tripod Stand Home Outdoor Screens Cinema Portable 1 6,490.00 6,490.00 73 Pcs Calculator. Basic Calculator Big Calculator. Office Supplies. Dimension: 160.4x164.5x44.2mm. Color White. Dual Power Supply. Aaa Battery With Solar Panel. Inner Concave Buttons. 5 500.00 2,500.00 74 Unit Touch Screen Tv – Not Less Than 55" Android Tv (free Installation) 1-year Service Warranty 1 61,000.00 61,000.00 75 Pcs Cork Bulletin Board (20x30cm Cork Board With Black Wooden Frame) 1 430.00 430.00 76 Pcs Convertible Drawing And Drafting Table (manual Lift Dimension W-7.75 X D 24x H22" To 31.5") 3 8,400.00 25,200.00 77 Pcs Table. Desk Painting Easel (wooden Easel Stand For Painting 1.75m Complimentary Screws Firm And Strong) 5 454.00 2,270.00 78 Pcs Gauze Bandage (sterile Gauze Bandage 3x10 Per Box) 2 300.00 600.00 79 Pcs Povidine-iodine 120ml (antiseptic Wound Solution) 5 250.00 1,250.00 80 Pcs Artist Taboret (35 ½" H X 17 ½" W X 14 ½" D+9/cm X 44cm X 37 Cm 1 26,784.00 26,784.00 81 Pcs Medicine Cabinet Large. Dimension: 29 X16.5x16 Cm 2 1,500.00 3,000.00 82 Pcs Sewing Machine (zigzagger) Power：90w, Rated Voltage：220v, Number Of Stiches：23, Automatic Winding. Presser Foot Pressure Adjustable (free Installation) 1 25,000.00 25,000.00 83 Pcs Sewing Machine (electric) (portable Sewing Machine With 23 Stitches (free Installation) 2 15,000.00 30,000.00 84 Pcs Tailors’ Scissors (10") Heavy Duty 5 1,500.00 7,500.00 85 Pcs Glue Gun (20w High Temperature) 5 111.00 555.00 86 Pcs Acrylic Color (set 12 Pc X 12 Ml) 5 368.00 1,840.00 87 Pcs Scissors, 5" Blunted Scissors, Plastic Handle. 5 112.00 560.00 88 Pcs Cutters. Snap Off Blade Knife Blade, Refill 9 Mm 5 13.00 65.00 89 Pcs Watercolors (50 Color Solid Watercolors Tin Box (202'82'33mm) 5 441.00 2,205.00 90 Pcs Art Paper (assorted Colors, Short Size) 5 270.00 1,350.00 91 Pcs Paint Brushes (12 Pcs Fine Detail Paint Brush) 5 246.00 1,230.00 92 Pcs Yarn (yarn Hand Knitting And Crochet Single Color (5 Colors) 5 30.00 150.00 93 Pcs Glue (1 Bottle 240g) 5 126.00 630.00 94 Pcs Colored Pencils (colored Pencils 12/set) 5 190.00 950.00 95 Pcs Colored Pens (fine Line Colored Marker 24 Colors In Pvc Bag) 5 90.00 450.00 96 Pcs Sewing Pins (sewing Pins 40 Pcs/set0 5 10.00 50.00 97 Pcs Sewing Needles(hand) (sewing Needles Big And Small) 5 18.00 90.00 98 Pcs Rotary Cutter (45mm) 5 169.00 845.00 99 Pcs Tape Measure (body Tape Measuring Ruler Tailoring) 5 16.00 80.00 100 Pcs Crochet Hooks (100 Pcs Crochet Hook) 5 286.00 1,430.00 101 Pcs Knitting Needles (2 Pcs/set (35cm) Knitting Sweater Stick Needle Bamboo Sweater Needle Knitting Scarf Tool) 5 144.00 720.00 102 Pcs Crochet Thread (thread Yarn 175 M) 5 46.00 230.00 103 Pcs Sewing Thread (polyester 1000 M) 5 42.00 210.00 104 Pcs Painting Easel. Studio/ (90/150 Cm Easel Wooden Standard Painting Display) 5 569.00 2,845.00 105 Pcs Manual Pencil Sharpener (one -hole Sharpener Tub) 5 68.00 340.00 106 Pcs Doll Mannequin. Whole Body With Stand Decor Body Dress Full Body Display 5 411.00 2,055.00 107 Pcs Transparent Edge T- Square (hand Tool Inch Metric Ruler 6") 5 535.00 2,675.00 108 Pcs Wood Carving Set. Carpentry Tools (professional 12/set Manual Wood Carving) 5 1,670.00 8,350.00 109 Pcs Staple Gun. (gun Tacker/ Staple Gun Length-18cm Width -12cm H-3cm, Color- Silver Head T50) 5 226.00 1,130.00 110 Pcs Slope Sink. (single Bowl Stainless Steel Kitchen Sink Box 15" Single Bowl Kitchen Sink Sus 304) 5 21,892.00 109,460.00 111 Pcs Roofing Square. Dual Marking Right Angle Picture Framing Carpenter Ruler (wadlow Stainless Steel Angle Ruler Aluminum Alloy Body Heavy Duty Tool) 5 216.00 1,080.00 112 Pcs Professional Compound Mitre Box & Saw (mitre Box And Box Saw Set 12 Inch) Miter Box Will Handle Stock 7 1/4" High, 8" Wide At 90°, And 5" Wide At 45°. The Saw Can Be Set At Any Angle And Has Automatic Stops For 90°, 45°, And For 5, 6, 8 And 12-sided Frames. 1 1,510.00 1,510.00 113 Pcs Drawing Lamp (metal Adjustable Arm Work Desk Lamp) 5 373.00 1,865.00 114 Pcs Chisel Rack For Wood Carving (professional 12-piece Wood Carving Chisel Set With Black Case Sharp Hand Tools For Beginners) 5 1,299.00 6,495.00 115 Pcs Corner Clamp (90-degree Single Swing Jaw Corer Clamp 68 Mm) 5 258.00 1,290.00 116 Pcs Decorative Realistic Artificial Fruits (realistic Artificial Fruit Such As Apples, Orange, Lemon, Pineapple And Banana) 5 293.00 1,465.00 117 Pcs Geometric Shapes Set (wooden Montessori Learning Geometric Building Blocks) 5 1,176.00 5,880.00 118 Pcs Geometric Designer Templates (multi -functional Geometric Ruler) 5 118.00 590.00 119 Pcs Stack Rack (toy Origami Rack Shelves) 5 1,477.00 7,385.00 120 Pcs Picture Frame And Miter Clamp (90 Degree Right Angle Clip Picture Frame) 5 710.00 3,550.00 121 Pcs Heat Gun (heat Gun With Accessories 2000 W) 5 1,725.00 8,625.00 122 Pcs Tape Dispenser (tape Dispenser 1") 5 114.00 570.00 123 Pcs Multi- Function Three - Hole Puncher (multi-dimensional 3 -hole Puncher) 5 4,176.00 20,880.00 124 Pcs Metric Scale (technical Triangular Scale. Set Of 45, 90 Degrees) 5 68.00 340.00 125 Pcs Steel Tape Measure (tape Measure 8m/20) 5 470.00 2,350.00 126 Pcs Heavy Duty Circular Saw (7-¼" 1600w) 5 4,104.00 20,520.00 127 Pcs Abrasive Disc Cutter Machine (ssc22 14-inch Cut Off Saw Machine 2200w) 5 7,577.00 37,885.00 128 Pcs Manual Canvas Pliers (industry Line Combination Plier Insulated Pliers) 5 416.00 2,080.00 129 Pcs Jet-bow Beam Compass Drawing Set. The Set Includes 6" Speed Compass With Inter-changeable Pen, Pencil, Divider Parts, And Replaceable Needle Points. 4½" Bow Compass With Inter-changeable Pen, Pencil, And Divider Parts. 5 1,169.00 5,845.00 130 Pcs Human Head Model(2 Pack 17" Foam Head Female Wig Head 5 4,791.00 23,955.00 131 Pcs Screw Drivers Set( 9 Pcs Multi-purpose Magnetic Screwdriver Set 5 226.00 1,130.00 132 Pcs Pliers. Pliers And Grip Set (premium 4 Pcs Insulated Pliers Set) 5 2,904.00 14,520.00 133 Pcs Artist Stool With Wheels (stainless Steel Stool Bar) 5 1,991.00 9,955.00 134 Pcs Screen Print Squeegee (curved Aluminum Handle Squeegee 75) 5 308.00 1,540.00 135 Pcs Mixing Paint Palette (paint Mixing Palette 10 Well Plastic) 5 45.00 225.00 136 Pcs Carving Chisels For Wood (wood Chisel 4 Pcs/set) 5 798.00 3,990.00 137 Pcs Files Set For Wood Carving, Craft Metal, And Glass Stone (10-piece Needle File Set For Jewelries) 5 191.00 955.00 138 Pcs Heavy Duty Multi- Purpose Bench Vise (8") Mounted On A Steel Platform. 2 15,000.00 30,000.00 139 Pcs Anvil (15 Kg) With Steel Mounting Platform 2 12,000.00 24,000.00 140 Unit Electric Angle Grinder. Heavy Duty 4" 1000w Professional Power Tools Grinders Variable-speed 3 2,500.00 7,500.00 141 Box Cutting Disc For Steel. Ultra-thin Cutting Disc 4 (25pcs) For Stainless 5 2,000.00 10,000.00 142 Pcs Cutting Discs For Masonry. 4”-inch Professional Diamond Cutting Disc Continuous Eco For Tile / Ceramic 20 300.00 6,000.00 143 Set Drill Bits.3-12mm Multifunctional Triangle Glass Metal Drill Bit Set Diamond Ceramic Tile Concrete Brick Wood Punching Hole Drill Bits 5 500.00 2,500.00 144 Set Drill Bits. 13pc Cobalt High Speed Steel Twist Drill Bit Set 1.5mm-6.5mm For Drilling Metal Wood Stainless Steel 5 500.00 2,500.00 145 Set Drill Bits For Wood. 7pc X Long Wood Drill Bit Set 4mm 5mm 6mm 7mm 8mm 10mm 12mm X 300mm Brad Point Auger Drill Bits Wood 5 500.00 2,500.00 146 Set Electric Wood Power Planer. Wood Planer For Woodworking. 1200 Watts. 1300 Rpm. 50 Hz. 80mm Wide. With Accessories. With Warranty 3 3,000.00 9,000.00 147 Unit Impact Drill 13mm Hammer Electric Drill Heavy Duty 220v Household Power Tools Industrial Screwdriver. 7.5 Amp Copper Motor, 700w, 3300rpm. With Warranty 3 3,000.00 9,000.00 148 Box Welding Rod Special N-6013 (2.5) (3/32 X 13”) 10kg Per Box 4 2,500.00 10,000.00 149 Unit Electric Welding Machine. Portable Igbt Inverter Welding Machine (dc Inverter Welding) With Accessories. With 3 Mos. Warranty 3 5,000.00 15,000.00 150 Pcs Welding Protective Suite (genuine Whole Leader Welding Apron) 5 2,362.00 11,810.00 151 Pcs Welding Hood Cape (standard Size) 5 311.00 1,555.00 152 Pcs Welding Gloves 5 186.00 930.00 153 Pcs Welding Protective Visor Glasses, Standard 5 420.00 2,100.00 154 Pcs Welding Mask (welding Helmet Auto Darkening Adjustable) 5 465.60 2,328.00 155 Pcs Hard Hat (heavy Duty Safety Helmet With Chin Strap) 5 291.00 1,455.00 156 Pcs Compact Electric Kilns (quick Fire A Kiln Controller) 2 39,305.00 78,610.00 157 Pcs Heat Press Transfer Machine (multi-function Heat Press Machine Flatbed: 30 Cm X 38 Cm) 2 11,808.00 23,616.00 158 Pcs Hammer For Carpentry. Claw Hammer /16oz 5 300.00 1,500.00 159 Set Hacksaw Frame With Blade For Metal 12" 300mm Heavy Duty 5 350.00 1,750.00 160 Pcs Wooden Hand Saw. 18" High Quality Metal Blade With Plastic And Rubber Handle 5 350.00 1,750.00 161 Pcs Steel Measuring Tape. Fluorescerous Tape 10m Portable Self Lock Tape Measure Meter Tape Tools 5 350.00 1,750.00 162 Pcs Tri Square. High Quality Metal Frame 12" With Clear Markings 5 750.00 3,750.00 163 Pcs Level Bar. Aluminum Level Bar With Magnet Heavy Duty 80cm 2 2,000.00 4,000.00 164 Pcs Plumb Bob / Hulog. With String 350g 5 250.00 1,250.00 165 Set Rachet. Combination Wrench Steel Chrome Vanadium 8-24mm (per Piece) 5 500.00 2,500.00 166 Set Ratchet Wrench. 12pcs 1/2 1/4-inch Drive Ratchet Wrench Cr-v Socket Kits Mechanic Spanner Car Motorcycle Repair Tool 5 700.00 3,500.00 167 Pcs Adjustable Wrench. Industrial Adjustable Wrench (12") 300mm Made Of High-quality Steel. 5 350.00 1,750.00 168 Set Back Wrench. Set Of Heavy-duty Double Ring Spanner Wrench (metric 28mm - 32mm) Cr-v 5 500.00 2,500.00 169 Set Combination Wrench Tool Set 16pcs (8-32mm Professional Dual Purpose 5 700.00 3,500.00 170 Set Magnetic Screwdriver Set Professional Cushion Grip 5 Flat Head And 4 Phillips Tips Screwdriver Non-slip 5 1,000.00 5,000.00 171 Set Allen Wrench. Short Arm Hex Allen Key Set With Carbon Steel Material. (1.5 To 6 Mm 7 Pcs Set) 5 100.00 500.00 172 Set Heavy Duty Pliers. 8"standard Pliers Cutter Longnose Combinations 8"pliers 5 500.00 2,500.00 173 Pcs Water Pipe Wrench 18” Liyabe Tubo Yabe Hand Tools 5 500.00 2,500.00 174 Set Chisel For Wood. 90 Mm Wooden Handle. 12pcs Professional Manual Wood Carving Hand Chisel Carving Tool Set, 8mm-14 Mm High Quality Steel Blade. 5 900.00 4,500.00 175 Set Wood Planer Set -katam. Locally Manufactured 8 Inches 2 500.00 1,000.00 176 Pcs Rubber Mallet (16 Oz) 5 258.00 1,290.00 177 Pcs Ball Peen Hammer (½ Lb. (80 Oz) 5 376.00 1,880.00 178 Pcs Cutting Mat 6680412 5 268.00 1,340.00 179 Pcs Heavy Duty Extension Wire (10-meter Wire: 162 C, Plug: 15a, 25 V, Maximum Wattage:3750 W., At Least 4 Outlets) 5 900.00 4,500.00 180 Set Microphone With 5-meter Cord, Anti-interference, Anti-whistling. 2 1,500.00 3,000.00 181 Pcs Portable Sound System With Microphone ( Active Portable Trolley Speaker , 600w Max Power, Bluetooth + Tws, Usb & Sd Playback, Fm Radio, Line-in & Line -out, 2 Guitar Input, 2 Wired Mic Input, 180 Channels, Mic Priority, High Quality Lead Acid 12ah Battery, 12 Dc Input, Dimensions: (l) 36.5cm (w) 40 Cm (h) 67.5 Cm, 2 Fee Wireless Mic) 2 20,000.00 40,000.00 182 Pcs Camera Flash. 92 Ft./28 M) 2 13,800.00 27,600.00 183 Pcs Camera Lens (18-200mm F/3.5-5.6 Lens 2 40,336.00 80,672.00 184 Pcs Camera Tripod (aluminum Tripod Digital Camera Tripod Mobile Phone Selfie Stands) 2 2,500.00 5,000.00 185 Pcs Studio Lights (soft Light) 4 10,200.00 40,800.00 186 Hdmi Cord. Hdmi Male To Male Cable Hd104 10110 10 Meter. 4k/60hz 2 1,500.00 3,000.00 187 Hdmi Cord. 5 Meters. Two-color Injection Plug Double Shielded Cable Body. Hdmi2.0 Version. Resolution: 0.75m-3m Support 4k 60hz; 5m Support 4k 30hz Only. Awg:30awg (0.75m-5m) 5 600.00 3,000.00 188 Pcs Soft Box Stand And Reflector Holder (50x70 Cm Soft Box Lighting Kit) 2 442.00 884.00 189 Pcs Monolights (200 W) 2 3,931.00 7,862.00 190 Pcs Reflector With Holder (holder /arm Stand Kit) 2 2,891.00 5,782.00 191 Pcs Boom Light Stand And Reflector Holder (420 Lb. Light Boom Stand With Weight Bag Up To 5kg Maximum Lead Capacity) 3 5,508.00 16,524.00 192 Pcs Background (4.22 M Background Paper 1.36 X 10m) 3 1,438.00 4,314.00 193 Pcs Display Panel Board (display Parallel Board) 1 14,290.00 14,290.00 194 Pcs Offline Mini Compressor (air Compressor Kwv550 9l Oil Less 3 4,558.00 13,674.00 195 Pcs Styrofoam Cutter (electric Foam Cutter Hot Wire Pen Portable) 5 238.00 1,190.00 196 Pcs Potter's Wheel/ Electric Potter's Wheel / Cutter (220 Volts Pottery Wheel) 1 6,228.00 6,228.00 197 Pcs Fire Blanket (with Pvc Pouch 1.2m X 1.2 M) 3 624.00 1,872.00 198 Pcs Smoke Detector X-sense Xs01 Mini Smoke Detector- Stand Alone 3 1,799.00 5,397.00 199 Pcs Disposal Bins (trash Bins 75 L) 3 1,804.00 5,412.00 200 Pcs Dressing Mirror (whole Body Mirror With 4 Wheels Height 5ft. Width 14 Inches) 1 1,500.00 1,500.00 201 Pcs Dish Towels (10 Pc. Per Set 25 Cm X 25 Cm Microfiber Super Absorbent) 10 993.00 9,930.00 202 Pcs Steamer. 3 Layer Steamer 32cm Stainless Steel Cooking Pots Cookware Steam High Quality 3 1,156.00 3,468.00 203 Pcs Soap Dish (dual Soap Case With Cover & Handle- Bathroom Soap Dish / Soap Case) 50 70.00 3,500.00 204 Pcs Detergent (detergent Powder Set 6 Kilos-i Kilo X 6 Pouches) 50 288.00 14,400.00 205 Pcs Hand Soap (liquid Hand Soap Antibac 1 Gallon) 50 216.00 10,800.00 206 Pcs Pots (extra Size #4 (26cm Diameter 16 Cm In Height) 20 673.00 13,460.00 207 Pcs Pans (nonstick) 5 194.00 970.00 208 Pcs Toilet Paper Holder (wall Mounted Bathroom Toilet Paper Holder Tissue) 2 238.00 476.00 209 Pcs Dipper (plastic Dipper L 11" X W 36"x H 41" 2 15.00 30.00 210 Pcs Pail (utility Pail With Metal Handle 10l/26x27 Cm) 2 111.00 222.00 211 Pcs Trash Can (with Plastic Swing Lid L-27 Cm, W- 17.5cm, H- 40.5 Cm) 2 260.00 520.00 212 Pcs Toothbrush (extra Clean Toothbrush 5 Pk -soft) 20 182.00 3,640.00 213 Pcs Hairbrush (natural Wood Hairbrush Comb) 20 120.00 2,400.00 214 Pcs Comb (1 Dozen Suklay 3-hole X Sz-28 Big) 20 90.00 1,800.00 215 Pcs Toothpaste (red 100 Ml) 20 60.00 1,200.00 216 Pcs Plastic Tumbler 20 300.00 6,000.00 217 Pcs Razor (twin Blade Disposable Razors) 20 120.00 2,400.00 218 Pcs Nail Clipper (stainless Nail Clippers H-8 Cm Wt-0.046 Kg) 20 100.00 2,000.00 219 Pcs Nail File (12 Pcs Red Nail File (medium) 20 50.00 1,000.00 220 Pcs Deodorant (roll On 50 Ml Bottle) 20 150.00 3,000.00 221 Pcs Face Towel (basic Face Towel - Free Size) 20 100.00 2,000.00 222 Pcs Feminine Napkin (silk Floss 12 Pcs) 200 50.00 10,000.00 223 Pcs Dust Catcher With Broom (2n1 Broom Dustpan Set Windproof Floor Sweeper With Broom) 5 170.00 850.00 224 Pcs Feather Duster (soft Magic Feather Duster Long Size And Colorful Colors (plastic) 5 150.00 750.00 225 Pcs Wash Rags (round Rags) 5 30.00 150.00 226 Pcs Floor Map (magic Spin Mop With Bucket 360° Rotating Floor Cleaning Plastic Liner) 5 264.00 1,320.00 227 Pcs Garbage Can (super Convenient Mini Flip Lid Trash Can (plastic) 10 150.00 1,500.00 228 Pcs Sponge (high Density Double-sided Dishwashing Sponge 7x10x3 Cm) 10 30.00 300.00 229 Pcs Spray Bottle (garden Sprayer Capacity: 500ml) 10 170.00 1,700.00 230 Pcs Table Napkin (1 Ply 40s Sheets Folded) 10 21.00 210.00 231 Pcs Place Mat (table Placemat Pvc Anti-slip Placemat Washable Durable Kitchen S:30x45cm) 10 25.00 250.00 232 Dozen Plates (12 Pcs Plates 8-inch Melamine White) 6 358.00 2,148.00 233 Set Drinking Glass (drinking Glass 10 Oz Tall Clear Tumblers Set Of 6 L=5.5cm H-12 Cm) 6 510.00 3,060.00 234 Pcs Pitcher (durable Crystal-clear Glass 1.5l) 6 258.00 1,548.00 235 Pcs Bowl (serving Bowls, Clear Glass 20 Cm Diameter) 6 72.00 432.00 236 Pcs Water Dispenser. Hot And Cold Water/drinking Household Multifunctional Top Loading. Stainless Steel Casing Color White. Dimension: 85x29x29 Cm. Large Bottom Locker. 3 3,000.00 9,000.00 237 Pcs Electric Hand Drier (free Installation) 1 5,000.00 5,000.00 238 Pcs Water Pail. (utility Pail With Metal Handle 10l Color: Red/ Blue L-27cm, W-27cm, H-26 Cm 6 335.00 2,010.00 239 Bot Dish Washing Liquid. Kalamansi Lemon Antibac Hygiene 780ml Bottle 10 350.00 3,500.00 240 Pack Laundry Powder Soap. 5 Kg Supra Clean, Natural Scent 10 600.00 6,000.00 241 Pcs Laundry Bar Soap (scrubber Bar 125g) 120 18.00 2,160.00 242 Pcs Clothesline (1 Pc Nonslip Clothesline 35 M) 20 10.80 216.00 243 Pcs Clothes Pin (laundry Clothes Pins Spring Clips 24 Pcs Plastic) 20 48.00 960.00 244 Pcs Wash Basin (laundry Basin 23 Inch) 10 504.00 5,040.00 245 Pcs Laundry Bag Set (4 Pcs/set Laundry Washing Bag- 1 Pc M(30cmx40cm) 1pc L (40cmx50cm) 1pc Xl (50x60 Cm) 10 150.00 1,500.00 246 Pcs Ironing Board (ironing Board With Stand Portable 43"iron Board (70cm To 86 Cm) 5 1,300.00 6,500.00 247 Pcs Flat Iron (non-stick Teflon Saleplate Spray Function Ht & Width 251x170x120mm 5 870.00 4,350.00 248 Pcs Mono Bock Chair, Standard Size. White. Load Capacity 200kg. 20 600.00 12,000.00 249 Pcs Curtain Rod (steel +anti-rust Coating, Adjustable Size: Large 120 Inches) 10 1,200.00 12,000.00 250 Pcs Curtain (1pc 5x7 Ft. Window Curtain With 8-hole Grommet Rings For Bedroom And Living Room) 10 714.00 7,140.00 251 Dozen Hangers (12 Pcs. Plastic Hanger) 2 150.00 300.00 252 Pcs Washing Machine. 7.0 Kg Digital Inverter Fully Automatic Top Load Washing Machine (water Level: 5, Gross Weight: 31kg, Net Weight: 27 Kg Gross Dimension: (wxhxd)=580x890x600mm Net Dimension: (wxhxd)= 540x857x568mm) 2 20,000.00 40,000.00 253 Pcs Vacuum Cleaner (heavy Duty Gas 12-25 Pl Wet And Dry Vacuum Cleaner/ Extractor With Power Socket System 1,250 W Weight-9kg, Max Input Power- 1,250 W, Max Vacuum Power-200 Mbar) 5 11,547.00 57,735.00 254 Pcs Socks (cotton Socks Unisex High Street Socks Sixe:38-44 2 50.00 100.00 255 Pcs Dress (sleeve Ruffle Hem Plain Elegant) 1 500.00 500.00 256 Pcs Slippers (sizes 10, Flipflop Brand Light Weight And Durable 2 132.00 264.00 257 Pcs Mattress (for Single Size Bed Size Polyester 3.5 Inch Thick 6 4,440.00 26,640.00 258 Bed Foam (for Single Bed, 3 Inches Thick) 3 3,500.00 10,500.00 259 Pcs Pillows (foam Pillow 4x12x20) 3 426.00 1,278.00 260 Pcs Bedsheets (cotton Full Garterize 3n1 Bed Sheets, L-60in Ww-75in (for Single Bed Size) 3 300.00 900.00 261 Pcs Alarm Clock (3-inch Retro Mute Quartz Bell Alarm Clock Movement Bedside With Night Light And Loud Alarm) 1 450.00 450.00 262 Pcs Handheld Rechargeable Pool Vacuum. • Strong Built-in 4v 2ah Ni-mh Rechargeable Batteries • Suitable For Use With All Purespas And Above Ground Pools Up To 18 Feet Or 5.49 Meters In Diameter • 0.21 Gal (0.8 Liters) Quick Release Transparent Debris Container • 12 Gal/min. (45 Liters/minute) Water Suction For Efficient Debris Collection • 94 Inches (2.39m) Lightweight Telescoping Aluminum Pole • Two Interchangeable Brush Heads • Automatic Shut-off Feature When Vacuum Is Not Submerged In Water • Ipx8 Waterproof Switch For Added Protection • 5-6 Hour Charge Time / 50 Minutes Maximum Running Time • Usb Charging Cable Included For Convenient Recharging (plug Not Included) 3 9,998.00 29,994.00 263 Pcs Swimming Pool Leaf Skimmer. Purpose: Used For Cleaning Swimming Pool And Salvaging Pool Water Garbage. Material: Pp Plastic. Size: 420*280*30mm/16.54*11.02*1.18". 5 376.00 1,880.00 264 Pcs Pack Of 300 Pcs Chlorine Tablet For Swimming Pool. Adjustable Chlorine Dispenser 8 Inchin Combination With Mont, 3-inch Chlorine Tablets Adjust The Water Flow Rate And Hereby The Amount Of Chlorine Dissolved In Your Pool Package Included:1*chlorine Dispenser +300pcs Pool Cleaning Tablet Or 300pcs Pool Cleaning Tablet 20 500.00 10,000.00 265 Pcs Adaptive Swim Life Jacket For Disabled. Keeps The User’s Face Out Of The Water. Stops The Tension Of The Neck. Upright Position. Back Support. Therapist Hands Free! Double Harness Distributes Tension’s Adjustment. Possibility To Add The Harness Pad (or “cuissard” In French) No Latex. 5 11,000.00 55,000.00 266 Pcs Bakery Display Rack (estante). Made Of Glass And Aluminum Frame. 4 Layer Of Glass (transparent) Or Acrylic With Partition. Rubber Wheels With Lock. At Least 2ftx 5ftx 4 Ft 2 40,000.00 80,000.00 267 Pcs Bread Rack. Made Of 12 Mm Steel. 24"x5ftx5ft. Can Hold Up To 10 Trays (lagayan Ng Plantsa Ng Tinapay) 2 10,000.00 20,000.00 268 Pcs Cookery Cabinets (made With Carbon Steel 5 Layers, Size: H: 144cm, W: 55cm) 3 3,621.00 10,863.00 269 Set Housekeeping Cart. Multi-functional Movable Cleaning Cart Housekeeping Property Cleaning Tool Cart Special Trolley. Standard For Housekeeping Work. 5 5,000.00 25,000.00 270 Set Shopping Cart Utility Cart Trolley Grocery Cart For Warehouse Garden Supermarket 5 6,000.00 30,000.00 271 Pcs Kitchen Carts (2 Layer Stainless Steel Carts With Two Brake Wheels; Size: 400mm X 500mm X 860mm) 2 3,019.00 6,038.00 272 Pcs Weighing Scale Digital. Display Mode: Led/lcd+light. Weighing Range :40kg. Accuracy: 2g. Product Size: 35x33x14cm 3 Lcd Display On The Operator’s Side Of The Scale As Well As 3 Lcd Display On The Customer’s Side. Minimum Capacity Is 2g. Maximum Capacity Is 40kg Power Source: Built In Rechargeable Battery With Usb Cable Battery Powered Or Connect Usb Cable. Battery Powered Or Connect Usb Cable To Use Weight Platform/tray Material Is Stainless Steel. 4 7,000.00 28,000.00 273 Pcs Measuring Cup. Measuring Cup Sizes: 1 Cup (250ml). 1/2 Cup (125ml). 1/4 Cup (60ml); 1/8 Cup (30ml). Materials. Plastic (abs) 6 500.00 3,000.00 274 Pcs Measuring Spoon 1tbsp 15ml 1/2tbsp 7.5ml Ltsp 5ml 1/2tsp 2.5mlmaterial: Stainless Steel+pp Packing: Pp Bag 6 400.00 2,400.00 275 Pcs Measuring Urn - Glass, Capacity: 100 Ml. (with 10 Ml Increments), Metric And English System Of Measurement; With Handle And Spout, Clear, Non- Porous, Tempered Glass 6 450.00 2,700.00 276 Pcs Wire Whisk - Length: 30 Cm (12 ") Material Stainless Steel 6 320.00 1,920.00 277 Pcs Chef's Knife (stainless Steel) 33cm X 4.5cm X 2cm 6 750.00 4,500.00 278 Pcs Boning Knife (stainless Steel) 24.4cm X 1.9cm X 1.7cm 6 492.00 2,952.00 279 Pcs Oysters Knife (stainless Steel) 15.5com X 6.5cm X 3cm 6 187.00 1,122.00 280 Pcs Cleaver Knife (stainless Steel) 7 Inches Or 2.5mm 6 1,074.00 6,444.00 281 Pcs Tenderizer (pin Tenderizer) Stainless Steel Diameter: 5cm, Height: 19cm 6 119.00 714.00 282 Pcs Tenderizer Mallet. (tenderizer) Stainless Steel 12.6 Inches X 11.5x4cm 6 240.00 1,440.00 283 Pcs Skimmer, Fine (stainless Steel) 7.3cm X 5cm X 21.5cm 6 160.00 960.00 284 Pcs Wire Skimmer, Small (stainless Steel) Handle: 14; Radius: 14 6 105.00 630.00 285 Pcs Skimmers, Spider (stainless Steel) Handle: 14; Radius: 20 6 115.00 690.00 286 Pcs Strainer, Small, Fine (stainless Steel) Diameter:14cm; Length: 29cm; Depth: 5.5cm 6 160.00 960.00 287 Pcs Colander Strainer (stainless Steel) 48cm X 20cm X 12cm 6 298.00 1,788.00 288 Pcs Siever, Small (stainless Steel) 14 Cm 6 188.00 1,128.00 289 Pcs Strainer, Medium, Fine (stainless Steel) Diameter:16cm; Length: 30.5cm; Depth: 5.9cm 6 180.00 1,080.00 290 Pcs Turner (stainless) Dimension: 34.5 X 9.8 X 4.4 Cm 6 280.00 1,680.00 291 Pcs Spatula (silicon) 27.2 X 5.5 X 1.5cm 6 169.00 1,014.00 292 Pcs Wooden Spoon (made With Beech Wood 10cm X 34cm X 2cm) 6 244.00 1,464.00 293 Pcs Parisienne Scoop (stainless Steel Blade With Plastic Handle) Scoop Diameter: 30mm And 27mm; Total Length: 170mm 6 216.00 1,296.00 294 Pcs Fruit Juicer, Standard Type 6 1,500.00 9,000.00 295 Pcs Zester (stainless Steel) Length: 30cm/11.81 Inches 8 268.00 2,144.00 296 Pcs Piping Bag (disposable Bag Size: 24.5cm X 17cm 8 208.00 1,664.00 297 Pcs Pastry Tubes (stainless Steel) 3cm X 3cm X 6.1cm 8 142.00 1,136.00 298 Pcs Strainer, Chinois, Small (stainless Steel) 16cm Handle: 5.5inches 8 198.00 1,584.00 299 Pcs Filling Funnel (stainless Steel) Upper Diameter: 10.5cm, Lower Diameter: 3.7cm, Height: 4.5cm 4 212.00 848.00 300 Pcs Measuring Spoon (1set: 1tbsp, 1/2tbsp, 1tsp, 1/2tsp, 1/3tsp, 1/4tsp) 6 245.00 1,470.00 301 Pcs Tongs (stainless Steel) 9 Inches 10 110.00 1,100.00 302 Pcs Tongs (stainless Steel) 12 Inches 8 179.00 1,432.00 303 Pcs Ice Cream Scoop (stainless Steel) Diameter: 4.5cm, Length: 18cm 6 208.00 1,248.00 304 Pcs Cheese Cloth (made From Cotton) 101 X 270cm 10 223.00 2,230.00 305 Pcs Serving Spoon (heavy-duty Stainless Steel) Length: 22.5cm; Width: 6cm 24 102.00 2,448.00 306 Pcs Pepper And Salt Grinder (made With Stainless Steel, Glass And Ceramic) Approx. 19x6.5cm 6 296.00 1,776.00 307 Pcs Core Seed Remover (stainless Steel; Approx: 1.4x21.5cm) 8 229.00 1,832.00 308 Pcs Wire Whisk, Small (stainless Steel+plastic Handle; 8 Inches) 8 180.00 1,440.00 309 Pcs Wire Whisk, Medium (stainless Steel+plastic Handle; 10.2 Inches) 8 189.00 1,512.00 310 Pcs Wire Whisk, Heavy Duty (stainless Steel+plastic Handle; 14 Inches) 2 258.00 516.00 311 Pcs Can Opener (stainless Steel Blade; Length: 17cm High) 1 370.00 370.00 312 Pcs Muti-purpose Kitchen Scissors/ Shears (scissors Length: 21.5cm; Blade Length: 10cm; Handle Length: 11.5cm; Handle Width: 9.5cm; Blade Thickness: 0.4cm Weight: 200grams) 8 368.00 2,944.00 313 Pcs Soup Ladle, 4 Oz (stainless Steel; Size: 7.5cm X 30 Cm) 8 124.00 992.00 314 Pcs Soup Ladle, 6 Oz (stainless Steel; Size: 7.5cm X 30 Cm) 8 194.00 1,552.00 315 Pcs Soup Ladle, 8 Oz (stainless Steel And Wooden Handle: 10 X 51 Cm) 3 290.00 870.00 316 Pcs Soup Ladle, 12 Oz (stainless Steel And Wooden Handle: 15 X 51 Cm) 2 360.00 720.00 317 Pcs Kitchen Spoon (stainless Steel; Size: 8cmx6.5cmx21cm) 8 86.00 688.00 318 Pcs Kitchen Spoon, Slotted (material: Plastic; Size: 7x3x43cm) 8 289.00 2,312.00 319 Pcs Kitchen Fork (stainless Steel; Size: 7cmx4cmx21cm) 4 72.00 288.00 320 Pcs Carving Fork (stainless Steel; Size: 13 Inches Long) 3 162.00 486.00 321 Pcs Digital Kitchen Thermometer (cooking/food Temperature; Size 34mm X 270mm) 2 486.00 972.00 322 Pcs Muti-function Vegetable Fruit Peeler Slicer Cutter Chopper (material: Abs + Stainless Steel) 2 429.00 858.00 323 Pcs Stock Pot, Big (with Glass Cover; Size: 34.5 X 27.9 Cm X 16.6 Cm) 2 798.00 1,596.00 324 Pcs Frying Pan, Small (scratch Resistant And Non-stick; Size: 20cm) 4 233.00 932.00 325 Pcs Frying Pan, Medium (scratch Resistant And Non-stick; Size: 24cm) 4 380.00 1,520.00 326 Pcs Frying Pan, Large (scratch Resistant And Non-stick; Size: 28cm) 2 578.00 1,156.00 327 Pcs Colander, Small (stainless Steel; Size: 24cm X 22cm) 3 204.00 612.00 328 Pcs Colander, Medium (stainless Steel; Size: 28cm X 22cm) 2 298.00 596.00 329 Pcs Cutting Board (material: Bamboo; Size: 34x24x1.8cm/750g) 4 209.00 836.00 330 Pcs Heavy Duty Electric Grill Machine 2 10,000.00 20,000.00 331 Pcs Portable And Foldable Charcoal Barbeque Grill 25"x30"x27" 2 2,000.00 4,000.00 332 Unit Cotton Candy Machine, Power 950 Watts, Speed 3600 Rpm, Pre Heating Time 1 To 3 Minutes, 515 Mm Diameter Stainless Drum. 1 5,000.00 5,000.00 333 Pcs Fish Poacher, Medium (stainless Steel With Tempered Glass Cover; Size: 24cm X 38.7cm X 10cm) 1 983.00 983.00 334 Pcs Casserole, Small (stainless Steel: 2.1 Liter; Size: 12cm X 15cm) 6 599.00 3,594.00 335 Pcs Casserole, Medium (stainless Steel: 3.9 Liter; Size: 12.5cm X 20cm) 4 689.00 2,756.00 336 Pcs Wok, Small (nonstick Carbon Steel; Size: 32cm) 4 389.00 1,556.00 337 Pcs Wok, Medium (nonstick Carbon Steel; Size: 36cm) 1 401.00 401.00 338 Pcs Double Boiler, Medium (stainless Steel; Size: 27x14x6cm) 1 389.00 389.00 339 Pcs Paella (heavy Duty Carbon Steel; Size 25cm) 8 581.00 4,648.00 340 Pcs Glass Rack (plastic-coated Metal; Capacity: 24pcs Glass; Dimension: L:52cm; W: 36cm; H:8cm) 2 461.00 922.00 341 Pcs Soup Cup Rack (2 Layered Rack; Size: 35 X 25 X 28cm) 3 899.00 2,697.00 342 Pcs Plate Rack (stainless Steel; Size: 30cmx22.8cmx12.9cm) 2 492.00 984.00 343 Pcs Baking Tray, Small (stainless Steel; Size Details: 23cm X 17cm) 8 258.00 2,064.00 344 Pcs Utility Tray (stainless Steel: Stain Resistant; Size: 45cm X 35cm X 4.8cm) 12 189.00 2,268.00 345 Pcs Roasting Pan (stainless Steel; Size: 31.5 X 24.5 X 2.5 Cm) 4 378.00 1,512.00 346 Pcs Dish Towels (highly Absorbent Cloth With 3pcs Per Pack) 8 98.00 784.00 347 Pcs Cooler, 2.5ft X 2.5 Ft X 3ft Plastic, With Good Insulation 1 3,000.00 3,000.00 348 Pcs Plastic Silverware Or Real Silverware (stainless Steel; 18pcs Utensils Set Includes: 6 Dinner Fork, 6 Dinner Spoons And 6 Dinner Teaspoons) 2 415.00 830.00 349 Pcs Glasses. Dining Glasses (6pcs. Thick Clear Glass: W: 3inches And H: 4inches) 6 265.00 1,590.00 350 Pcs Teacups (ceramic White; Capacity: 250ml) 2 188.00 376.00 351 Pcs Small Plate / Saucers (ceramic With Size: 6 Inches And 6pcs Per Set) 6 140.00 840.00 352 Pcs Cabinet Dish Organizer (2 Layered Metal Dish; Size:41.5cm X 30cm X 47cm) 1 2,499.00 2,499.00 353 Pcs Sponge And Soap Holder For Kitchen (stainless Steel) 18x 10 X 9cm 3 418.00 1,254.00 354 Pcs 11-piece Pots/pans (stainless Steel) 1 5,158.00 5,158.00 355 Pcs Silicone Kitchenware Set. Composed Of Slotted Spoon 12". Soup Ladle 12". Solid Turner 12". Tongs 10". Whisk 9.5". Basting Brush 10.8". Pasta Server 12.5". Round Spatula 12". Spoon 12.5" Spatula 12.6" And Utensils Holder. 6 647.50 3,885.00 356 Pcs Rotary Eggbeater (stainless Steel) 31cm /12.2", W:9.5cm/3.74" 2 340.00 680.00 357 Pcs Dough Scraper (stainless Steel) 16x12x2cm 3 178.00 534.00 358 Pcs Gas Range And Oven (1 Turbo, 1 Large And 2 Medium Burners) 33x42x39.5, (49 Liters ) 1 46,162.00 46,162.00 359 Pcs Refrigerator (7 Cubic Feet, Stainless Look) Two Door Direct Cool 1 15,717.00 15,717.00 360 Pcs Kitchen Cupboards (7 Doors, 3 Drawers) 120x 40x90 Cm 2 13,198.00 26,396.00 361 Pcs Cooking Brush (silicone) Heat Resistant 3 82.00 246.00 362 Pcs Blender. (9 In1 Food Processor, Good For Chopping, Slicing,grating,shredding, Whisking)18x18x38cm 3 3,742.00 11,226.00 363 Pcs Mechanical Microwave Oven (countertop,20 Liters) 700w - 1200w 3 5,075.00 15,225.00 364 Pcs Kitchen Scale Food (manual) 5 Kilogram 2 252.00 504.00 365 Pcs Measuring Spoons (stainless Steel, 6pcs Heavy Duty) 3 258.00 774.00 366 Pcs Measuring Cups (12 Pieces, Bpa -free Plastic Long Lasting Used) Large And Medium Cups 3 2,208.00 6,624.00 367 Pcs Kitchen Shears (stainless Steel) 9 Inches/ 225mm 3 357.00 1,071.00 368 Pcs Potato Masher With Soft Grip Handle (stainless Steel) 9.5x27x8cm 3 357.00 1,071.00 369 Pcs Medium Graters (stainless Steel) 18/8 3 430.00 1,290.00 370 Pcs Funnel (stainless Steel) 22x14.5cm 3 715.00 2,145.00 371 Pcs Can Opener (automatic) 16.3x 1.5cm 3 698.00 2,094.00 372 Pcs Cast Iron Pots And Pans (ceramic, Non-stick) 21.85x 13.19x12.80inch 3 7,180.00 21,540.00 373 Pcs Gas Stove. 2 Burner Built In Gas Stove ( Stainless Steel) 73x41x9cm With Hose And Safety Regulator. 5 3,640.00 18,200.00 374 Pcs Lpg Tank 11kg 6 5,000.00 30,000.00 375 Unit Electric Stove. Stainless Frame. Multifunctional Induction Cooker Inverter Electric Stove Heavy Duty Energy-saving 3500w 220v. All Copper Heating Coil. Five Speed Power Adjustment. Explosion Proof. With Digital Display Panel. 5 2,500.00 12,500.00 376 Pcs Double Broiler Steamer (stainless Steel) 30 Cm Diameter 3 2,730.00 8,190.00 377 Pcs Kitchen Knife Set (stainless Steel And Poly Propylene Plastic Handle) 15x7.5x34cm 3 840.00 2,520.00 378 Pcs Meat Slicer (electric Machine Stainless Steel) 418x 293x 325mm 3 2,494.00 7,482.00 379 Pcs Bread Toaster (stainless Steel Top Plate) 25x 14.6x16.8cm 3 1,059.00 3,177.00 380 Pcs Cookie Press (stainless Steel With 13 Disc And 8 Icing Tips 25x 14.5cm 3 462.00 1,386.00 381 Pcs Cake Decorating Kit. Piping Tips Set ( Stainless Steel, Multicolor) 3 279.00 837.00 382 Pcs Serving Bread Tray (stainless Steel) 45cmx2.8cm 6 1,229.00 7,374.00 383 Pcs Hot Plate Single Electric Stove (1000 W) 8.8x8.8x1.4 Inch 2 583.00 1,166.00 384 Pcs Electric Oven. Height (cm): 32.5. Highlights. Width (cm): 37.5. Warranty: 1 Year Warranty On Electrical Parts And Lifetime Free Service. Net Weight (kg): 7.3. Capacity: 2.8 Liters Length (cm): 49. Gross Weight (kg): 8.2. 5 11,000.00 55,000.00 385 Pcs Oven. Four Plates Oven For Bread (stainless Steel) 530x595x570mm. Lpg Type 1 48,924.00 48,924.00 386 Pcs Bread Plates (stainless Steel) 40x 60cm 20 1,027.00 20,540.00 387 Pcs Bread Rack (stainless Steel)15 Layers 40x60cm Heavy Duty 1 20,000.00 20,000.00 388 Pcs Electric Burger Griddle. Large Size Heavy Duty. Size: 73cmx52cmx10cm. Bigger Waster Oil Container. Stainless Steel, Solid Gritty. Food Grade Material. 2 11,475.00 22,950.00 389 Pcs Food Warmer Display Cabinet. Commercial Food Heater Glass Display Cabinet Heavy-duty Curved Deli Cabinet With Lighting. Constant Temperature Heating Display Counter Ideal For Fried Chicken Burger And Cooked Food. Size: Red+3 Compartments: 96x45x60cm. Rated Power: 300w. Rated Voltage: 220v.number Of Internal Layers: Three. Layers. Temperature Range: 30-80°c. Product Weight: 18kg. Built-in Energy-saving Warm Color Lamp, Improve The Display Effect 2 9,125.00 18,250.00 390 Pcs Frying Pan (non-stick, 28 Cm) 3 1,690.00 5,070.00 391 Pcs Measuring Spoon. 1tbsp 15ml. 1/2tbsp 7.5ml. Ltsp 5ml. 1/2tsp 2.5mlmaterial: Stainless Steel+pp. Packing: Pp Bag. 3 400.00 1,200.00 392 Pcs Measuring Cups (12 Pieces, Bpa -free Plastic Long Lasting Used) Large And Medium Cups 3 2,209.00 6,627.00 393 Pcs Measuring Urn. Glass, Capacity: 100 Ml. (with 10 Ml Increments), Metric And English System Of Measurement; With Handle And Spout, Clear, Non- Porous, Tempered Glass 3 450.00 1,350.00 394 Pcs Mixing Bowl: 30 Cm L30xw27.5xh11.4 Cm Thickness: 0.04 Cm. Material: Stainless Steel 12 900.00 10,800.00 395 Pcs Baking Sheet 11x15 Inches 011 Thickness Heavy Duty Aluminum 10 360.00 3,600.00 396 Pcs Wire Whisk Length: 30 Cm (12 ") Material Stainless Steel 5 320.00 1,600.00 397 Pcs Muffin Pan Non-stick Muffin Pan Dimension: 26.5x35x3cm Capacity: 12 Cup Color: Black Non-stick Surface For Easy Release And Quick Cleanup Dishwasher Safe Ideal For Baking Muffins, Cupcakes, And More Nonstick Coating Helps Ensure Effortless Food Release 5 700.00 3,500.00 398 Set Measuring Spoon 1tbsp 15ml 1/2tbsp 7.5ml Ltsp 5ml 1/2tsp 2.5mlmaterial: Stainless Steel+pp Packing: Pp Bag 6 400.00 2,400.00 399 Set Measuring Cups (12 Pieces, Bpa -free Plastic Long Lasting Used) Large And Medium Cups 6 2,209.00 13,254.00 400 Pcs Measuring Urn Glass, Capacity: 100 Ml. (with 10 Ml Increments), Metric And English System Of Measurement; With Handle And Spout, Clear, Non- Porous, Tempered Glass 6 490.00 2,940.00 401 Pcs Mixing Bowl 30 Cm L30xw27.5xh11.4 Cm Thickness: 0.04 Cm Material Stainless Steel 6 900.00 5,400.00 402 Pcs Baking Sheet 11x15 Inches 011 Thickness Heavy Duty Aluminum 10 360.00 3,600.00 403 Pcs Wire Whisk Length: 30 Cm (12 ") Material Stainless Steel 5 320.00 1,600.00 404 Pcs Electric Stove, 1000 Watts, 12" Diameter, Stainless Steel. With Safety Regulator And Power Indicator. 6 1,500.00 9,000.00 405 Pcs Weighing Scale, Digital "display Mode: Led/lcd+light Weighing Range :40kg Accuracy: 2g Product Size : 35x33x14cm 3 Lcd Display On The Operator’s Side Of The Scale As Well As 3 Lcd Display On The Customer’s Side Minimum Capacity Is 2g. Maximum Capacity Is 40kg Power Source: Built In Rechargeable Battery With Usb Cable Battery Powered Or Connect Usb Cable. Battery Powered Or Connect Usb Cable To Use Weight Platform/tray Material Is Stainless Steel." 4 7,500.00 30,000.00 406 Pcs Scraper(rubber) 30cm X11cmx6.8cm 5 130.00 650.00 407 Pcs Hand Mixer (stainless Steel Bowl) 270x165x290mm, 2.8 Liters Capacity 5 1,755.00 8,775.00 408 Pcs Revolving Cake Stand (aluminum) 12 Inches 5 850.00 4,250.00 409 Pcs Electric Stand Mixer 5.5 Liter(1.9kg) With Bowl And 3 Whisk 6 Speed Setting Dough, Rotating Bowl, Speed Control 3 11,500.00 34,500.00 410 Pcs Rolling Pin Stainless Steel Pressing Stick Pizza Dough Non-stick Dough Roller, (29.5 Cm) 6 300.00 1,800.00 411 Pcs Dough Roller Pin, Wooden. 29.5cm Non-stick Silicone Rolling Pin Pastry Baking Decorating Tool 6 300.00 1,800.00 412 Set Deep Fryer Dimensions (w X H X D) 477 X 318 X 235 Weight 3.81kg Body Material Stainless Steel Color Silver Technical Details Power Consumption 2000w Volume 4l Features Temperature Control Yes 6 7,200.00 43,200.00 413 Pcs Ice Crusher Machine. Electric Stainless Steel Heavy Duty Portable Automatic Rotated Speed: 1500rpm Power:250 Size: 275x190x210mm Capacity: 2 Liter 2 3,900.00 7,800.00 414 Pcs Chest Freezer (inverter) Dual Function Technology (freeze Or Chiller) Solid Top With Glass Cover Inside Digital Temperature Control W/ Lcd Display Dimension: 85:112:70cm 1 28,535.00 28,535.00 415 Set Electric Takoyaki Machine And Double Pan 56 Holes Stainless Steel Size: 437x 435x180mm 6 2,600.00 15,600.00 416 Pcs Waffle Iron Pan 4 Interchangeable Plates 750 Watts 6 1,800.00 10,800.00 417 Pcs Revolving Cake Stand. Nonslip Top And Base. Diameter: 23.5 Cm. Height 14cm. Material: Food Grade Pp. 6 1,076.00 6,456.00 418 Pcs Stainless 4-gas Burner, 55l Gas Oven Hybrid Electric And Lpg 1 40,000.00 40,000.00 419 Pcs Electric Kettle 1.5l 3 900.00 2,700.00 420 Pcs Stand-up Kitchen Mixer-standard (4 Liters Stainless Steel Bowl With Cover) Tilting Mixing Arm. Accessories: Beater, Dough Hook, Whisk. 12 Speed Setting. 2 10,000.00 20,000.00 421 Pcs Hand Mixer. Powerful 180w Motor And 7 Speeds Including Turbo Setting Made Of Stainless-steel Abs. Multifunctional With Chrome Accessories: X2 Beaters, X2 Dough Hooks 5 2,500.00 12,500.00 422 Unit Rice Cooker Standard 2l Home Multifunctional Home Cooking 220v. Fast Cooking, Keep Warm Function, Non-stick Coating, Stainless Steel Cover. Input Voltage. 220v. Power Consumption 400w. Volume Capacity 2l Dimension (l X W X H) 215*215*215 3 2,500.00 7,500.00 423 Unit Electric Rice Cooker 10l 2 5,000.00 10,000.00 424 Pcs Blender 1.5 Liter 5 700.00 3,500.00 425 Pcs Pressure Cooker 3.5 Liter 2 1,200.00 2,400.00 426 Pcs Gas Stove Rack. Plain Sheet With Steel Frame. With Cooking Platform At The Top. Kitchen Heavy Duty Gas Tank Holder Kitchen Organizer Stainless. Made Of Carbon Steel 45cmx45cmx90cm. Made Of Carbon Steel Color Black With Partition For 11kg Gasul Tank And For Cooking Materials. 4 5,500.00 22,000.00 427 Pcs Chef's Knife, 8" Stainless Steel 6 350.00 2,100.00 428 Pcs Bread Knife, 8" Stainless Steel 6 350.00 2,100.00 429 Pcs Clever Knife/ Butcher Knife To Chop Bones 20 Cm Blade, 31 Cm From Tip To Handle 6 350.00 2,100.00 430 Pcs Kitchen Scissors 9" Stainless Steel 6 350.00 2,100.00 431 Pcs Utility Knife 61mmx19mm 6 350.00 2,100.00 432 Pcs Boning Knife, 8" Japanese High Carbon Steel 6 350.00 2,100.00 433 Pcs Paring Knife 4" German Stainless Steel 6 350.00 2,100.00 434 Pcs Stainless Peeler For Vegetables 15cmx6cm 6 80.00 480.00 435 Pcs White Cutting Board (for Bread And Pastry) 25.5cmx34cm, Plastic 6 460.00 2,760.00 436 Pcs Green Cutting Board (for Fruits And Vege)25.5cmx34cm, Plastic 6 460.00 2,760.00 437 Pcs Red Cutting Board (raw Meat)25.5cmx34cm, Plastic 6 460.00 2,760.00 438 Pcs Blue Cutting Board (raw Fish)25.5cmx34cm, Plastic 6 460.00 2,760.00 439 Pcs Yellow Cutting Board (cooked Meat) 25.5cmx34cm, Plastic 6 460.00 2,760.00 440 Pcs Brown Cutting Board (raw Crops) 25.5cmx34cm, Plastic 6 460.00 2,760.00 441 Pcs Weighing Scale (dial/analog. 25kg) 1 400.00 400.00 442 Pcs Digital Kitchen Scale 3kg/0.1g And 500g/0.1g 3 690.00 2,070.00 443 Pcs Measuring Cups (1 Set) 6 95.00 570.00 444 Pcs Plastic Measuring Pitcher Jug With Measurement(set) Maximum Of 1 Liter 6 126.00 756.00 445 Pcs Measuring Spoon, Plastic (set) 6 60.00 360.00 446 Pcs Deep Fry Thermometer, Deed Fried Pot Thermometer Oil Temperature Gauge 6 320.00 1,920.00 447 Pcs Meat Thermometer, Brifit Waterproof Kitchen Meat Thermometer, Foldable Digital Instant Read Food Thermometer 6 400.00 2,400.00 448 Pcs Oven Thermometer 6 389.00 2,334.00 449 Pcs Tenderizer, Wooden Circular-50mm Diameter, 3cm Spikes, 190mm Long (flashlight Design) 6 280.00 1,680.00 450 Pcs Skimmer, Fine Mesh Strainer Oil-frying Filter 7cm Diameter, 32 Long 5 80.00 400.00 451 Pcs Wire Skimmer 18cm Diameter, Stainless Steel 5 80.00 400.00 452 Pcs Strainer, Stainless Steel Multi-purpose Food Strainer, Fine Mesh Long Handle 20cm Diameter X 28cm (fine) 5 109.00 545.00 453 Pcs Siever 17.5x12x11.5cm, Stainless Steel Mesh Stainer 6 68.00 408.00 454 Pcs Strainer Medium 20cm Diameter X 28cm (fine) 6 90.00 540.00 455 Pcs Strainer Large 25cm Diameter X 30cm Long, Stainless Steel 6 120.00 720.00 456 Pcs Wooden Turner, Wooden Sandok Kitchen Spatula Spoon Turner Cooking, 3" Width Of Sandok, 10" Long 6 65.00 390.00 457 Pcs Wooden Spatula 9cm Sandok, 34 Cm Long 6 65.00 390.00 458 Pcs Parisienne Spoon, Double-ended Headed Fruit Ice-cream Ball 6 50.00 300.00 459 Pcs Wooden Ladle/spoon 6cm Pang Sandok 30 Cm Long 6 120.00 720.00 460 Pcs Zester, Four-sided Stainless-steel Grater 9-inch Kitchen Multipurpose Grater For Parmesan Cheese, Ginger Vegetables 6 79.00 474.00 461 Pcs Reusable Piping Bags. 26 Pcs/set Silicone Pastry Bag Tips Kitchen Diy Icing Piping Cream 24 73.00 1,752.00 462 Pcs Stainless Funnel Small 4.5cm Opening Diameter, 3.7cm Height, 0.6cm Tube Diameter 6 60.00 360.00 463 Pcs Stainless Funnel Small 5.5cm Opening Diameter, 5cm Height, 0.9cm Tube Diameter 6 70.00 420.00 464 Pcs Stainless Funnel Small 7.5cm Opening Diameter, 6.7cm Height, 1.2cm Tube Diameter 6 60.00 360.00 465 Pcs 8" Tongs 6 89.00 534.00 466 Pcs 12" Tongs 6 120.00 720.00 467 Pcs Pepper Mill, 5-inch Wooden Peeper Grinder 6 60.00 360.00 468 Pcs Salt Mill 5-inch Wooden Salt Grinder 6 60.00 360.00 469 Pcs Wire Whisks 12 Inches 6 80.00 480.00 470 Pcs Wire Whisks 8 Inches 6 89.00 534.00 471 Pcs Can Opener 6 120.00 720.00 472 Pcs Bottle Opener 6 79.00 474.00 473 Pcs Soup Ladle 3oz 6 140.00 840.00 474 Pcs Soup Ladle 6oz 6 160.00 960.00 475 Pcs Soup Ladle 8oz 6 160.00 960.00 476 Pcs Soup Ladle 12oz 6 180.00 1,080.00 477 Pcs Stock Pot, 30cm High Quality Stainless Steel 10 1,500.00 15,000.00 478 Pcs Stock Pot 24cm High Quality Stainless Steel 10 999.00 9,990.00 479 Pcs Frying Pan 22cm Marble Frypan 10 500.00 5,000.00 480 Pcs Frying Pan 28cm Marble Frypan 48.2x28x5.7cm 10 600.00 6,000.00 481 Pcs Casserole 18 Cm Aluminum, Double Handle, Rust Free 10 250.00 2,500.00 482 Pcs Casserole 20 Cm Aluminum, Double Handle, Rust Free 10 300.00 3,000.00 483 Pcs Casserole 28 Cm Aluminum, Double Handle, Rust Free 10 600.00 6,000.00 484 Pcs Wok 40 Cm Chinese Nonstick Wok Pan 10 500.00 5,000.00 485 Pcs Double Broiler 28 Cm Stainless Steel Two-layer Double Soup Steamed Dual Purpose 10 280.00 2,800.00 486 Pcs Glass Rack. 25-compartment Gray Full-size Glass Rack With 2 Blue Extenders 2 2,500.00 5,000.00 487 Pcs Plate Rack. Microwire 24 Compartment Catering Plate Rack For Plates Up To 11" - Wash, Store, Transport 3 3,000.00 9,000.00 488 Pcs Baking Tray 15"x17" 5 180.00 900.00 489 Pcs Roasting Tray 15"x17'' 5 180.00 900.00 490 Pcs Braising Pan 32cm Stainless Steel Nonstick Pan 5 350.00 1,750.00 491 Pcs Hanging Cabinet With Glass, Std. 2.5'x 3' X 5ft (free Installation) 3 10,000.00 30,000.00 492 Pcs Floor Mops (broom Type) Using Cotton Absorbent Strips 10 180.00 1,800.00 493 Pcs Broom (walis Tambo) 10 80.00 800.00 494 Pcs Dustpan (plastic) 11"x10" Pan, 24" Handle 10 120.00 1,200.00 495 Pcs Garbage Bin (4 Gals.) 10 300.00 3,000.00 496 Pcs Paper Towel Dispenser 10 200.00 2,000.00 497 Pcs First Aid Cabinet, Plastic Box 30cmx12cmx30co With Transparent Cover (free Installation) 2 1,500.00 3,000.00 498 Pcs Fire Extinguisher 3lbs Abc Dry Chemical Refillable (free Installation) 4 2,000.00 8,000.00 499 Pcs Mixing Bowl Small, Stainless Steel Mixing Bowl 20cm 12 80.00 960.00 500 Pcs Mixing Bowl Medium, Stainless Steel Mixing Bowl 30cm 12 130.00 1,560.00 501 Pcs Stainless Steel Basin, 45 Cm Diameter 5 180.00 900.00 502 Pcs Stainless Steel Basin, 38 Cm Diameter 5 120.00 600.00 503 Pcs Baking/ Pastry Brush, Heat Resistant, Standard Size 10 35.00 350.00 504 Pcs Plastic Containers, Microwavable Round Canister, Food Storage Container (400 Ml) 40 20.00 800.00 505 Pcs Multipurpose Plastic Pail 2.5 Gallons Capacity 4 120.00 480.00 506 Pcs Food Grade Silicone High Temperature Resistant Baking Mat Oven Baking (to Match Baking Pan), Browns Silicone Baking Oven Mat Liner, Non-stick For Pastry Cookies Dough 12 90.00 1,080.00 507 Pcs Non-slip Doormat 75x45 Cm Rubber 18 500.00 9,000.00 508 Pcs White Hand Towels Hanging Kitchen Hand Dry 20cmx30cm 12 30.00 360.00 509 Pcs Potholder, Basahan Bilog 6 Inches Diameter 12 15.00 180.00 510 Pcs Round Cake Molder 4, 6, 8 Inches Set 5 161.00 805.00 511 Pcs Square Cake Molder 9, 11, 13 Inches Set 5 160.00 800.00 512 Pcs Baguette Bake Mold Pan 34.5 Cmx 24cm (6cm Molder) Nonstick 10 399.00 3,990.00 513 Pcs Meat Processing Machine (meat Grinder Manual) 1 5,000.00 5,000.00 514 Set Stainless Icing Tip (set-12pcs) Cake Decorating Kit Stainless. Icing Piping Nozzles Pastry Tips Cake. 10 499.00 4,990.00 515 Pcs Cupcake Molder Tray Of 6 12 Holes Baking Pan Muffin Cup Cake 10 89.00 890.00 516 Pcs Large Wooden Turner For Large Oven. Kitchen Turner Flat Spatula Scraper, Acacia Wood 10.5 Inches Long And 2.75 Inches Turner 3 200.00 600.00 517 Pcs Dressing Mirror (whole Body Mirror With 4 Wheels Height 5ft. Width 14 Inches) 1 1,500.00 1,500.00 518 Set Dish Towels (10 Pc. Per Set 25 Cm X 25 Cm Microfiber Super Absorbent) 5 993.00 4,965.00 519 Pcs Soap Dish (dual Soap Case With Cover & Handle- Bathroom Soap Dish / Soap Case) 50 70.00 3,500.00 520 Pcs Detergent (detergent Powder Set 6 Kilos-i Kilo X 6 Pouches) 50 288.00 14,400.00 521 Pcs Hand Soap (liquid Hand Soap Antibac 1 Gallon) 10 216.00 2,160.00 522 Pcs Pots (extra Size #4 (26cm Diameter 16 Cm In Height) 20 673.20 13,464.00 523 Pcs Pans (nonstick 12") 5 195.00 975.00 524 Pcs Toilet Paper Holder (wall Mounted Bathroom Toilet Paper Holder Tissue) 2 238.00 476.00 525 Pcs Dipper (plastic Dipper L 11" X W 36"x H 41" 5 100.00 500.00 526 Pcs Pail (utility Pail With Metal Handle 10l/26x27 Cm) 8 250.00 2,000.00 527 Pcs Trash Can (with Plastic Swing Lid L-27, W- 17., H- 40.5 Cm) 5 350.00 1,750.00 528 Pcs Toothbrush (extra Clean Toothbrush 5 Pk -soft) 20 182.40 3,648.00 529 Pcs Hairbrush (natural Wood Hairbrush Comb) 20 120.00 2,400.00 530 Pcs Comb (1 Dozen Suklay 3-hole X Sz-28 Big) 20 90.00 1,800.00 531 Pcs Toothpaste (red 100 Ml) 20 58.20 1,164.00 532 Pcs Plastic Tumbler 20 300.00 6,000.00 533 Pcs Razor (twin Blade Disposable Razors) 20 120.00 2,400.00 534 Pcs Nail Clipper (stainless Nail Clippers H-8 Cm Wt-0.046 Kg) 20 84.00 1,680.00 535 Pcs Nail File (12 Pcs Red Nail File (medium) 20 50.00 1,000.00 536 Pcs Deodorant (roll On 50 Ml Bottle) 20 150.00 3,000.00 537 Pcs Face Towel (basic Face Towel - Free Size) 20 110.00 2,200.00 538 Pcs Feminine Napkin (silk Floss 12 Pcs) 50 45.00 2,250.00 539 Pcs Dust Catcher With Broom (2n1 Broom Dustpan Set Windproof Floor Sweeper With Broom) 10 350.00 3,500.00 540 Pcs Feather Duster (soft Magic Feather Duster Long Size And Colorful Colors (plastic) 10 110.00 1,100.00 541 Pcs Wash Rags (round Rags) 10 30.00 300.00 542 Pcs Floor Mop (magic Spin Mop With Bucket 360° Rotating Floor Cleaning Plastic Liner) 10 900.00 9,000.00 543 Pcs Garbage Can (super Convenient Mini Flip Lid Trash Can (plastic) 10 150.00 1,500.00 544 Pcs Sponge (high Density Double-sided Dishwashing Sponge 7x10x3 Cm) 10 118.00 1,180.00 545 Pcs Spray Bottle (garden Sprayer Capacity: 500ml) 10 155.00 1,550.00 546 Pcs Table Napkin (1 Ply 40s Sheets Folded) 10 50.00 500.00 547 Pcs Place Mat (table Placemat Pvc Anti-slip Placemat Washable Durable Kitchen S:30x45cm) 10 50.00 500.00 548 Set Plates (12 Pcs Plates 8-inch Melamine White) 3 634.00 1,902.00 549 Set Drinking Glass (drinking Glass 10 Oz Tall Clear Tumblers Set Of 6 L=5.5cm H-12 Cm) 1 718.00 718.00 550 Pcs Pitcher (durable Crystal-clear Glass 1.5 L) 2 300.00 600.00 551 Pcs Bowl (serving Bowls, Clear Glass 20 Cm) 2 130.00 260.00 552 Pcs Water Pail (utility Pail With Metal Handle 10l Color: Red/ Blue L-27cm, W-27cm, H-26 Cm 4 350.00 1,400.00 553 Pcs Laundry Bar Soap (scrubber Bar 125g) 120 20.00 2,400.00 554 Pcs Clothesline (1 Pc Nonslip Clothesline 35 M) 20 140.00 2,800.00 555 Pcs Clothes Pin (laundry Clothes Pins Spring Clips 24 Pcs Plastic) 20 100.00 2,000.00 556 Pcs Wash Basin Plastic (laundry Basin 23 Inch) 5 250.00 1,250.00 557 Pcs Laundry Bag Set (4 Pcs/set Laundry Washing Bag- 1 Pc M(30cmx40cm) 1pc L (40cmx50cm) 1pc Xl (50x60 Cm) 10 200.00 2,000.00 558 Pcs Ironing Board (ironing Board With Stand Portable 36"iron Board (70cm To 86 Cm) 5 1,600.00 8,000.00 559 Pcs Flat Iron (non-stick Teflon Saleplate Spray Function Ht &width 251x170x120mm 5 1,000.00 5,000.00 560 Pcs Pants. Standard Slacks Medium Size 3 1,000.00 3,000.00 561 Pcs Polo. Public School Uniform Type. Medium Size 3 500.00 1,500.00 562 Pcs Blouse. Public School Uniform Type. Medium Size 3 500.00 1,500.00 563 Pcs Skirt. Commonly Used In Public School Type. Medium 3 600.00 1,800.00 564 Pcs Long Sleeves. Cotton, Medium Size 3 1,000.00 3,000.00 565 Pcs T-shirt With Collar. Cotton, Medium Size 3 800.00 2,400.00 566 Pcs T-shirt Without Collar. Cotton, Medium Size 3 500.00 1,500.00 567 Pcs Maong Pants. Medium Size, Female Cut, Medium 3 1,000.00 3,000.00 568 Pcs Maong Pants. Medium Size, Female Cut, Medium 3 1,000.00 3,000.00 569 Pcs Maleta. 7kg Hand Carry Luggage Travel Bag. 360 Universal Wheels. Divided Internal Space. 57 Liters Capacity. 40 X 57 X25 Cm Dimension. 3 1,500.00 4,500.00 570 Pcs Chef’s Hat. Chef Cap For Men Women Chef Head Cap Breathable Hat Fast Food Restaurant Coffee Shop Work Wear. Large Size. Black 20 250.00 5,000.00 571 Chef’s Hat. Chef Cap For Men Women Chef Head Cap Breathable Hat Fast Food Restaurant Coffee Shop Work Wear. Medium Size. White 20 250.00 5,000.00 572 Pcs Chef’s Hat. Chef Cap For Men Women Chef Head Cap Breathable Hat Fast Food Restaurant Coffee Shop Work Wear. Small Size. White 20 250.00 5,000.00 573 Pcs Chef’s Apron. Black Apron With 2 Large Pockets Adjustable Apron Halter Neck Unisex Dirt And Stain Resistant. Large 20 450.00 9,000.00 574 Pcs Chef’s Apron. Black Apron With 2 Large Pockets Adjustable Apron Halter Neck Unisex Dirt And Stain Resistant. Medium 20 450.00 9,000.00 575 Pcs Chef’s Apron. Black Apron With 2 Large Pockets Adjustable Apron Halter Neck Unisex Dirt And Stain Resistant. Small 20 450.00 9,000.00 576 Pcs Hair Net. Unisex Hair Net Cap Hair Mesh Weaving Wig Cap Hair Styling Tools Nylon Hair Nets Hollow Out High. Black 300 30.00 9,000.00 577 Dozen Hangers (12 Pcs. Plastic Hanger) 1 181.00 181.00 578 Pcs Wash Basin. Aluminum 32" Diameter. 6 1,500.00 9,000.00 579 Pcs Washing Machine. 7.0 Kg Digital Inverter Fully Automatic Top Load Washing Machine (water Level: 5, Gross Weight: 31kg, Net Weight: 27 Kg Gross Dimension: (wxhxd) 580x890x600mm Net Dimension: (wxhxd)= 540x857x568mm) 3 25,000.00 75,000.00 580 Pcs Vacuum Cleaner (heavy Duty Gas 12-25 Pl Wet And Dry Vacuum Cleaner/ Extractor With Power Socket System 1,250 W Weight-9kg, Max Input Power- 1,250 W, Max Vacuum Power-200 Mbar) 2 12,000.00 24,000.00 581 Pcs Socks (cotton Socks Unisex High Street Socks Sixe:38-44 5 200.00 1,000.00 582 Pcs Dress (sleeve Ruffle Hem Plain Elegant Red Small, Medium, Large) 3 500.00 1,500.00 583 Pcs Slippers (sizes 7-10, Flipflop Brand Light Weight And Durable 5 150.00 750.00 584 Pcs Mattress For Single Bed (30x75 Single Size Polyester 3.5 Inch Thick) 5 4,440.00 22,200.00 585 Pcs Pillows (foam Pillow 4x12"x20") 5 426.00 2,130.00 586 Pcs Bedsheets (cotton Full Garterize 3n1 Bed Sheets, For Single Bed Size) 5 1,100.00 5,500.00 587 Pcs Alarm Clock (stopwatch, Digital Timer) 5 850.00 4,250.00 588 Pcs Goalball, Standard Size And Weight, Blue 2 20,000.00 40,000.00 589 Pcs Basketball, Standard Size 2 2,000.00 4,000.00 590 Pcs Soccer Ball, Standard Size 2 1,500.00 3,000.00 591 Set Bocce Balls, 100mm Diameter, 4 Balls Colored Red, 4 Balls Colored Green, With Palena Ball Color White. Set With Bag. 2 20,000.00 40,000.00 592 Piece White Cane For Adults- Foldable Aluminum With White Anodized Finish And Plastic Tip. The Tube Has A Spring Lock Pin For Adjusting Handle Height From 58-94 Cm. 10 1,500.00 15,000.00 593 Piece White Cane For Kids- Foldable Aluminum With White Anodized Finish. The Tube Has A Spring Lock Pin For Adjusting Handle Height From 58-94 Cm. 10 1,150.00 11,500.00 594 Set Chess Board For Blind. Plastic Pieces With Special Markings, Board With Pattern To Distinguish White And Black Squares With Slots To Hold The Pieces. At Least 12"x24" Plastic Board. 4 5,000.00 20,000.00 595 Set Scrabble Board For Blind. Made Of Plastic With Special Markings On Tiles And Board. At Least 18"x18" Board. 5 4,000.00 20,000.00 596 Set Dolch Basic Sight Words. (bitay Max). Printed On White Tarpaulin 2 Ftx 3 Ft Binded With Two Wooden Sticks. With String (sabitan). Words At Least 2" Height Black, Arial Font Style. 5 1,500.00 7,500.00 597 Pcs Meter Stick, 100cm Stainless Steel Ruler 5 500.00 2,500.00 598 Box Braille Paper. White Fanfold Tractor-feed Braille Transcribing Paper: 8.5 X 11 Inches, 3-hole And 19-hole Punch. Dimensions:10.1 × 11.5 × 5.4 Inches. 1000 Sheets 7 10,000.00 70,000.00 599 Box Braille Paper. 11.5"x 8.5". 1000 Sheets 5 7,000.00 35,000.00 600 Box Swell-touch Paper 11 X 11.5-in- 100 Sheets 1 10,000.00 10,000.00 601 Unit Braille Machine, Standard. With Leather Cover. With Warranty On Parts. 2 49,500.00 99,000.00 602 Pcs Braille Slate. 27 Lines, 30 Cells Per Row, Black 25 1,000.00 25,000.00 603 Pcs Braille Contraction Pamphlet. Unified Contraction Pamphlet 4"x6". 25 600.00 15,000.00 604 Pcs Contraction Pamphlet. Nemeth Code. 4"x6". 25 600.00 15,000.00 605 Pcs Cranmer Abacus 25 650.00 16,250.00 606 Pcs Braille Stylus. Round Or Y Shape 25 200.00 5,000.00 607 Set Geometric Measurement. Set Of Protractor, Ruler And Triangles Made Of Plastic With Embossed Marking For The Blind, Standard Size. 24 1,000.00 24,000.00 Delivery Terms: Within 30 Days Drop Off Points: General Santos City Sped Integrated School – Quezon Avenue, Brgy. West, Gsc (ilrc) Payment Terms: Payment To The Service Provider Shall Be Made Through Philippine Veterans Bank Lddap-ada / Mds. In The Case Of Accounts Maintained In Other Bank, Bank Transfer Fees Shall Be Chargeable Against The Creditor’s Account. ***nothing Follows*** Grand Total 7,338,507.00 2. The Deped Now Invites A Bid For The Above Procurement Project. Bidders Must Have Completed, Within Three (3) Years From The Date Of Submission And Receipt Of Bids, A Contract Similar To The Project With An Amount Of At Least 50% Of The Abc To Be Bid For Non-expendable And 25% Of The Abc For Expendable. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, I.e., In Section Ii, Instructions To Bidders. Bids Received That Exceed The Abc Per Lot Shall Be Rejected At Bid Opening. The Department Of Education, Division Of General Santos City Division Through Its Bids And Awards Committee (bac) Now Invites Bids For The Herein-mentioned Goods. Delivery Of The Goods Is Required On The Expected Delivery Date(s) Stated Herein. 3. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using A Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) 9184, Otherwise Known As The “government Procurement Reform Act.” Bidding Is Restricted To Filipino Citizens/sole Proprietorships, Partnerships, Or Organizations With At Least Sixty Percent (60%) Interest Or Outstanding Capital Stock Belonging To Citizens Of The Philippines, And To Citizens Or Organizations Of A Country The Laws Or Regulations Of Which Grant Similar Rights Or Privileges To Filipino Citizens, Pursuant To Ra 5183. 4. A Complete Set Of Bidding Documents In Soft Copy Only May Be Purchased At Deped-division Of General Santos City Bac Secretariat, Located At Tiongson St., Lagao, General Santos City Upon Submission Of A Letter Of Intent, And Payment In Cash On A Non-refundable Fee By Interested Bidders To The Deped Division Cashier. Only Bidders Who Purchased The Bidding Documents Provided Below Shall Be Allowed To Submit Bid/bids Not Later Than The Scheduled Receipt And Opening Of Bids. Bidding Document Price Lot Number Price Lot No. 1 P 10,000.00 5. It May Be Viewed Or Downloaded After Payment From The Website Of The Philippine Government Electronic Procurement System (philgeps), Www.philgeps.gov.ph. The Schedule And Venue Of The Procuring Activities Are As Follows: Activity Date And Time Venue Pre-bid Conference February 19, 2025 2:00 P.m. (wednesday) Sds Conference And Online Via Google Meet Issuance Of Bidding Documents Until March 5, 2025 9:00 A.m (wednesday) To Be Sent To Bidder’s Email Address After Payment Of The Bidding Documents Receipt And Opening Of Bids March 5, 2025 10:00 A.m. (wednesday) Division Office/google Meet Prospective Bidders Are Strongly Encouraged To Order Or Download The Electronic Copy Of The Bidding Documents From The Philgeps Website: Www.philgeps.gov.ph, For Them To Be Included In The Document Request List Of The Project. The Pre-bid Conference Is Open To All Interested Parties Who May Have Or Have Not Bought The Bidding Documents. 6. Bids Must Be Physically Delivered To The Address And On The Date And Time Stated Herein. Submission Of Digital Copy Of The Bidding Documents Shall Not Be Accepted. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 18. A Valid Bid Securing Declaration Must Accompany The Bid(s) In Lieu Of Bid Security. Bids Will Be Opened In The Presence Of The Bidder’s Representatives Who Choose To Attend The Opening Of Bids At The Address, Date And Stated Herein. Late Bids Shall Not Be Accepted. 7. The Deped-division Of General Santos City Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Not Award The Contract(s), Or Annul The Bidding Process Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 8. For Further Information, Please Refer To: Ofelia S. Panes Michael Jhon A. Del Sol Administrative Officer Iv (records) Administrative Assistant Ii Bac Secretariat Head Bac Secretariat Member Email: Ofelia.panes@deped.gov.ph Email: Bac.depedgensan@deped.gov.ph Cell No. 09692673871 Cell No. 09278865516 Approved By: Mervie Y. Seblos, Cese Oic – Assistant Schools Division Superintendent Bac Chairperson Bacsec/mds