Cable Tenders

Details: Description 1 Land Ambulance (type 1) 1 Unit I. Vehicle Specifications And Requirements · Vehicle Type: Four-wheel Passenger Van With 4 Doors (2 At The Front For The Driver And Passenger, One Sliding Door Or Barn Door At The Right Side And Tailgate Or Barn Door At The Rear) · Wheelbase: At Least 2,500-2,800 Mm · Drive Type: Rear Wheel Drive · Engine Size/displacement: 2,500 To 3,000 Cc · Engine Type: 4 Cylinders, In-line Type, 16 Valves, Double Over Head Cam (dohc), Maximum 3,400 Rpm · Alternator And Battery The Capacity Of The Alternator And Battery Must Be Sufficient To Supply The Additional Load Demands Of All Medical Equipment. The Amperage Capacity Of The Alternator Must Be At Least 110 Amperes. · Fuel-injector System: Direct Injection · Emission Compliance: Euro 4 · Fuel Type: Diesel · Fuel Tank Capacity: At Least 65 Liters · Transmission: Manual With At Least Five (5) Speed + One (1) Reverse · Steering: Left Hand Drive With Power-steering System · Brakes: Ventilated Disk On The Front And Ventilated Disk Or Drum Type On The Rear. With Anti-lock Braking System. With Parking Brake · Front Suspensions: Mcpherson Strut Or Double Wishbone Or Torsion Bar With Stabilizer · Rear Suspensions: Rigid Axle With Leaf Spring And Double Acting Shock Absorbers · Wheels: At Least 15 Inch, Aluminum Mag Wheels Or Steel Wheels With Full Cover · Tires: Radial Type And At Least 195 Mm Tire Width Standard Vehicle Lamps: Head Lamps, Tail Lamps, Stop Lamps, Signal Lamps, License Plate Lamps, Fog Lamps And Step Lamps · Vehicle Body Color: White · Floor Material: Metal With Anti-static Floor Matting. Each Entry Point Of The Patient Compartment Must Be Fitted With A Diamond Tread Plate Flooring. · Standard Dashboard Instrumentations: Speedometer, Odometer, Fuel Gauge, Digital Clock, Warning Lamps For Low Oil Pressure, Cooling Water Level, Overheating, Low Battery Charge, Indicator Lamps For Parking Brake And Head Light High-beam, Engine Check, Door Open. · Dashboard And Rear-view Camera System: Resolution Of At Least 1920x1080@30fps, Angle Of View At Least 120 Degrees Diagonal, At Least 2 Inch Led Display, Minimum Storage Capacity Of 64gb, With Loop Recording, Automatic On/off And Night Vision Recording In Low Light. The Cameras Must Be Permanently Installed On The Dashboard Or Windshield And At The Rear Part Of Vehicle. Rear-view Camera Must Be Have Color-coded Parking Grid Features. The Power Supply Must Be From The Vehicle Battery. · Standard Driver’s Cabin Accessories: Am/fm Radio With Speakers, Usb Connector, Front Personal Lamp For Driver And Passenger, Rear View Mirror, Sun Visor And Assist Grips For The Driver And Passenger. · Vehicle Doors Glass Windows: Central Or Power Door Locking System. Hydraulic / Electric Windows For Driver And Front Passenger Sides. The Vehicle Glass Windows (except The Windshield) Must Be Installed With Medium Shade (35% Visible Light Transmitted) Glass Tint. · Windshield Wipers: With At Least Three (3) Speed Intermittent With Washer · Air Conditioning System: Dual Type; At The Driver’s Cabin And At The Patient Compartment With Independent Controls. · Seat Belts: 3 Point Emergency Locking Retractor (elr) Seatbelts For The Driver And Front Passenger. · Airbags: Supplemental Restraint System (srs) Airbags For The Driver And For The Front Passenger. · Driver And Passenger Side Mirrors: Standard Convex Type, Manual Or Power Adjustment · Vehicle Interior Trim: Moulded Trim. The Ceiling Must Be Provided With Insulation. · Stainless Steel Plate On The Rear Bumper To Protect The Bumper When The Ambulance Stretcher Is Being Loaded To The Ambulance. · Set Of Tools: Hydraulic Jack, Tire Wrench, Flat And Philips Screw Drivers, Set Of Pliers, Adjustable Wrench, Early Warning Device And Spare Wheel And Tire. Ii. Emergency Lights, Sirens And Public Address System · Emergency Lights: Roof Mounted Light Bar With Red And Green Flashing Led Lights. The Length Of The Light Bar Must Be The Same As The Width Of The Vehicle Roof. Electric Siren And Public Address System: Standard Ambulance Siren Tones (horn, Manual, Wail, Yelp, Phaser, Hilo/two Tone) And With At Least Two 100 Watts Amplifier And Siren Speakers. With Rotary Switch And Momentary Push-button Override Control. Public Address Override With Attached Microphone And Volume Control Knob · Red And Green Flashing Led Lights Mounted On The Upper Part Of The Rear Of The Ambulance · Red And Green Led Flashing Lights Mounted On The Front Grill Of The Ambulance Iii. Ambulance Body Marking · The Front Of The Ambulance Shall Be Marked With A Reflectorized And Capitalized Word “ambulance” Which Is Spelled Out In Reverse (mirror Image). The Height Of Each Letter Shall Be No Less Than 10 Centimeters And The Word Shall Be Seen At Least Six (6) Meters Away. · Each Side Of The Ambulance Body Shall Have The Capitalized Word “ambulance” Not Less Than 15 Cm In Height And The Letters Must Be In Red Color. · The Rear Side Of The Ambulance Body Shall Be Marked With A Reflectorized And Capitalized Word “ambulance” Not Less Than 15 Cm In Height And The Letters Must Be In Red Color. · The Prescribed Doh Logo With A Diameter Of Not Less Than 36 Cm Shall Be Placed On The Driver’s Door And On The Front Passenger Door. Iv. Patient Compartment · Compartment Interior Height: At Least 1600mm · Compartment Interior Width: At Least 1500mm · Partition Between The Driver And Patient Compartment: Air Tight Bulkhead Made Of Non-porous Material With A Transparent And Shatter-proof Sliding Window At Least 35 Cm X 30 Cm. · Storage Cabinet For Medicines, Instruments And Medical Equipment > Built-in Cabinet Made Of White Painted Aluminum Panels Or Other Lightweight, Equivalent Strength Material Such As Fiberglass, Composites And Fiberglass Reinforced Plastics. The Cabinet Must Be Mounted On The Upper Left Side Of The Patient Compartment And Must Be At Least 200 Cm But Must Not Be More Than 210 Cm In Length. The Cabinet Must Be Firmly Anchored (bolted Or Welded) To Tapping Plates Of The Body Structure. > The Cabinet Must Have Transparent And Shatter-proof Sliding Doors With Low Profile Handles. The Sliding Doors Must Be Easily Opened But Must Not Open During Transit. The Sliding Doors Must Be Fitted With Automatic Latch Or Friction Holding Device. > The Cabinet Must Have At Least 4 Shelves With At Least One Shelf Designed To Fit And Carry Heavy Medical Equipment Such As The Defibrillator And Nebulizer. The Shelves Must Have A Depth At Least 30 Cm But Must Not Be More Than 50 Cm. · Compartment For The Folding Stretcher And Scoop Stretcher: Installed Below The Storage Cabinet, Made Of White Painted Aluminum Panels Or Other Lightweight, Equivalent Strength Material Such As Fiberglass, Composites And Fiberglass Reinforced Plastics. The Compartment Must Be At Least 200 Cm But Must Not Be More Than 210 Cm In Length. The Cabinet Must Be Firmly Anchored (bolted Or Welded) To Tapping Plates Of The Body Structure. Bench For Medical Personnel: The Ambulance Must Be Fitted With 3-seater Bench Permanently Mounted On The Ambulance Floor; One On The Head Side Of The Patient And One On The Right Side Of The Patient Compartment. The Bench (seat And Backrest) Must Be Made Of Sturdy Aluminum Frame And Panels Coated With White Color Paint Or Other Lightweight, Equivalent Strength Material Such As Fiberglass Reinforced · Plastics Or Plastic Laminated. The Seat And Backrest Must Be Fitted With Mattress Made Of Polyurethane Foam Covered With A Washable Leatherette Material. The Construction Of The Bench Must Be In Such A Way That The Underneath Can Be Used As A Compartment. The Bench Must Have A 2 Point Seatbelt For Each Person. > Overhead Lighting: At Least 2 Led White Lights With Low Light Option > Grab Rail: Aluminum Or Stainless Steel Grab Rail At Least 120 Cm Long, 10 Cm Depth (maximum) Installed On The Ceiling Right Above The Patient/ambulance Stretcher. > 220v Ac Supply: The Patient Compartment Must Be Installed With An Electronic Inverter With A Capacity Of At Least 3kva And An Output Voltage Of 220v, 60 Hz. At Least Five (5) Convenience Outlets Must Be Installed At The Different Points On The Compartment To Supply Power To The Medical Equipment. > Intercom System: Intra-vehicle Intercom System Must Be Fitted To Serve As Voice Communication Between The Driver And Personnel In The Patient Compartment. V. Communication Equipment Two (2) Pieces Cellular Phones (one For The Ambulance And One For The Hospital/base). The Cellular Phones Must Be 4g Network Capable, With Internal Memory Of At Least 64gb And 4gb Ram Smartphones. The Phones Must Be Provided With Sim Cards And Battery Charger. Vi. Medical Equipment And Instruments · Ambulance Stretcher > Length: 180 – 185 Cm > Width: 48 – 55 Cm > Loading Height Should Match The Vehicle Floor Height > Loading Capacity: At Least 175 Kg > Materials: Stainless Steel, High Grade Aluminum Alloy > Head Part Rising Angle: At Least 75° Knee Part Rising Angle: At Least 15° > With Collapsible Side Rails And Quick Release Patient Restrain System > With Durable Folding Leg Mechanism > The Mattress Must Be Made Of High-density Polyester Fiber Foam With A Thickness Of At Least 5 Cm And Covered With Waterproof Vinyl Material. > Wheels: 200 - 210mm Diameter, Fixed Front With Locking Brakes And Auto-directional Rear And With 50-55 Cm Loading Carriage Wheels > Loading Rail Mounted In The Ambulance With Latching System > Non-removable Doh Logo And The Words “for Ambulance Use Only” Must Be Marked On The Visible Part Of The Equipment. · Automatic External Defibrillator (aed) > Compact, Lightweight, Easy To Use, Bi-phasic Defibrillator With Manual (with Easy 1-2-3 Operation) > Waveform: Rectilinear Biphasic > Defibrillator Charge Hold Time: Not More Than 30 Seconds > Patient Safety: All Patient Connections Are Electrically Isolated > Charge Time: Less Than 10 Seconds With New Battery Charge To 200j With A Fully-charged Battery > Battery Operated > Self-test: Configurable Automatic Self-test When Device Is Turned-on > Monthly Full-energy Test (200j) > Automatic Self-test Checks: > Battery Capacity > Electrode Connection > Electrocardiogram And Discharge Circuits > Microprocessor Hardware And Software > Cpr Circuitry And Cpr-d Sensor And Audio Circuitry > Cpr: Metronome Rate (variable 60 To 100 Cpm) > Defibrillator Advisory: Evaluates Electrode Connection And Patient Ecg To Determine If Defibrillation Is Required > Shockable Rhythms: > Ventricular Fibrillation With Average Amplitude Of > 100 Microvolts > Wide Complex Ventricular Tachycardia With Rated Greater Than 150 Bpm For Adults And 200 Bpm For Pediatrics > Patient Impedance Measurement Range: At Least 0 To 300 Ohms > Defibrillator: Protected Ecg Circuitry > Display Format: Optional Lcd With Moving Bar > Size: Approximately 2.6” X 1.3” > Ecg Viewing Window: At Least 2.6 Seconds > Optional Ecg Display Sweep Speed: Not More Than 25mm/sec; 1”/sec > Data Recording And Storage > At Least 50 Minutes Of Ecg And Cpr Data. > If Audio Recording Is Installed And Enabled, At Least 20 Minutes Of Audio Recording, Ecg And Cpr Data. > If Audio Recording Is Disabled, At Least 7 Hours Of Ecg And Cpr Data. > Pc Minimum Requirements For Configuration And Patient Data Recovery: Windows® 98, Windows® 2000, Windows® Nt, Windows® Xp, Ibm Compatible Pii With 16550 Uart (or Higher) Computer. 64mb Ram. Vga Monitor Or Better. Cd-rom Drive. Irda Port. 2mb Disk Space. > Available With Pediatric Pacing Cable And Pads Synchronized And Direct Defibrillation > Biphasic Energy Waveform, Adjustable Output, From Approximately 1 Up To 200 Joules > Load Compensation Circuit Allows Precise Delivery Of Selected Energy, Based On Patient’s Impedance > Energy Selection > Charge Controls - Push-button Controls On Front Panel > Charge Time - Less Than 10 Seconds With New Battery Charge To 200j With A Fully-charged Battery > Charge/ready Is Indicated Via Audiovisual > Defibrillator Energy - Approximately ±15% At 50ω > Accuracy - Approximately ±30% Over The Range Of 25 To 100 Ω > Defibrillator Waveform - 5ms Monophasic Pulse Display Shows Ecg, Heart Rate, Battery Status And Energy Output Pre-set > Monitor Display Size: Bright Back-lit Alphanumeric Lcd, Approximately 10 X 6 Cm > Frequency Response: Non-diagnostic > Heart Rate Meter: Three-digit Readout Displays Rates From 20 To 300 Bpm > Heart Rate Alarm: User Selectable Alarm Limits > Self-test Is Performed Each Time The Device Is Switched On > System Reports, With Audiovisual Alert: Status, Operation, Malfunctions And Low Battery > Internal Safety Discharge Upon 40seconds Non-delivery Of Accumulated Energy, Switch-off And Technical Failure > Sensitivity, Adjustable 5, 10 And 20mm/mv Pads: > Shelf Life: 5 Years > Conductive Gel: Polymer Hydrogel > Conductive Element: Tin > Packaging: Multilayer Foil Laminate Pouch > Impedance Class: Low > Cable Length: At Least 36 In (91 Cm) > Sternum: Length: At Least 6.1 In (15.5 Cm); Width: At Least 5.0 In (12.7 Cm); Length, Conductive Gel: At Least 3.5 In (8.9 Cm); Width, Conductive Gel: At Least 3.5 In (8.9 Cm); Area, Conductive Gel: At Least 12.3 Sq In (79.0 Sq Cm) > Apex: Length: At Least 6.1 In (15.5 Cm); Width: At Least 5.6 In (14.1 Cm); Length, Conductive Gel: At Least 3.5 In (8.9 Cm); Width, Conductive Gel: At Least 3.5 In (8.9 Cm); Area, Conductive Gel: At Least 12.3 Sq In (79.0 Sq Cm) > Complete Assembly: Folded Length: At Least 7.6 In (19.4 Cm); Folded Width: At Least 7.0 In (17.8 Cm); Folded Height: At Least 1.5 In (3.8 Cm) > Design Standards: Meets Applicable Requirements Of Ansi/aami/iso Df-39-1993. > Shock Resistant Housing Allows System To Function In Demanding Environment > Integrated Carry Handle Facilitates Transport > Splash-resistant Alphanumeric Function Keys Power Supply: > User Replaceable Battery Is Removable/replaceable By The Operator. (10 Type 123a Photo Flash Lithium Manganese Dioxide Batteries. > Battery Capacity: Typical New (20°c) = 5 Years (at Least 225 Shocks) Or At Least 13 Hours Continuous Monitoring. End Of Life Designated By Red X (typical Remaining = At Least 9 Shocks). Battery Compartment To Be Clearly Labeled, Splash-proof And Requiring Tool For Opening For Battery Replacement > Electrical Source Requirements: Battery Operated > Operating Temperature: 32° To 122°f; 0° To 50°c > Storage Temperature: -22° To 140°f; -30° To 60°c > Humidity: 10 To 95% Relative Humidity, Non-condensing > Vibration: Mil Std. 810f, Min. Helicopter Test > Shock: Iec 68-2-27; 100g > Altitude: 300 To 15,000 Ft.; -91m To 4573m > Particle And Water Ingress: Ip-55. > Defibrillator Pads (self- Adhesive, Disposable And Non-polarized) At Least Five (5) Pairs For Adult And At Least Five (5) Pairs For Pedia Ø Non-removable Doh Logo And The Words “for Ambulance Use Only” Must Be Marked On The Visible Part Of The Equipment. · Nebulizer > Portable, Compressor-driven Nebulizer Pump, And A Four-pole Single Phase Motor Design In Metal Frame Construction > Easy To Operate With Sturdy Design For Use In Demanding Environment > Cup Capacity Minimum 3ml To Maximum 10ml > Nebulization, Approximately 0.1 To 0.2ml/minute > Residual Volume Maximum 2ml > Flow Delivery Range (under Load) 0.5 To Maximum 12 Liters/minute Or Greater > Median Mass Aerodynamic Diameter (mmad) Of Particles 0.5 To 4 Microns > Operating Temperature Range 5 To 50 ⁰c > Operating Relative Humidity Range Up To 65% > Compressor Requires No Maintenance And Delivers Oil-free Flow Diaphragm Type And Maximum Compressor Pressure Of 30 Psig Or Greater > Device, With Carry Handle, Is Provided With Accessory Storage Compartment > Power Supply, 220v/60hz > Power Consumption, Approximately 90w > System Configuration Accessories, Spares And Consumables: · System As Specified · Nebulizer Atomizer Body Piece (dome) · Reusable Mouth Piece, Pediatric Size (fitting Atomizer Body Piece) · Reusable Mouth Piece, Adult Size (fitting Atomizer Body Piece) · Air Tubing, Diameter Approximately 6/9mm (inner/outer), Length Approximately 1 Meter · Dosage Cup · Reusable Mask, Size Pediatric · Reusable Mask, Size Adult · Spare Inlet Filters · Spare Particle Filters · Set Of Spare Fuses · Portable Suction Machine > Electrical Suction Pump Supporting Medical Interventions Such As Resuscitation Or Minor Surgery > With Graduated Plastic Jar Auto-clavable, Capacity 1.2 Liters > Jar Is Covered And Fit With Overflow Valve And Antibacterial Filter > Suction Flow Maximum, Approximately 17l/minute > Vacuum Adjustable From 0 To Approximately - 600mmhg > Vacuum Control Button And On/off-switch > Sturdy Shock Resistant Casing, Easy To Carry And Easy Clean > Silent Operation Supplied With: > 2 X Set Of Silicone Tubes, Diameter 8/14mm (inner / Outer), Length Approximately 2.5m > 2 X Bi-conical Connectors Fitting The Silicone Tubes > 1 X Spare Jar Of 1l With Cover, Gasket And Overflow Valve > 1 X Set Of Spare Antibacterial Filters > 1 X Set Of Spare Fuses > 1 X Instructions For Assembly, Use And Maintenance, And List Of Accessories And Spare Parts With Product Reference Code In English Language > Consumables Should Be Available In The Local Market Power Supply > Power Input To Be 220-240vac (single Phase) / 60hz As Appropriate Fitted With Philippine Standard Plug > Voltage Corrector/stabilizer Of Appropriate Ratings Meeting Philippines Standard Specifications (input 160-260 V And Output 220-240 V And 60 Hz) > Power Consumption Approximately 50 Watts > Non-removable Doh Logo And The Words “for Ambulance Use Only” Must Be Marked On The Visible Part Of The Equipment · Examining Light (mounted On The Head Side Of The Patient) > Mobile Examination Light, Sturdy Construction. > On Heavy Base With 5 Swivel Castors, 2 With Brakes. Low Center Of Gravity For Optimal Stability And Reach > Single Lamp With Led Bulb: White Led Approximately 50,000 Hours Life > Field-of-view Diameter, Approximately 0.15 M At Working Distance > Homogeneous Illumination Across Entire Field-of-view, Approximately 20,000 Lux At 30.5 Cm To 50 Cm Working Distance > Color Temperature, Approximately 5500⁰k > Light Head Mounted On Spring Loaded Articulating Arm, Height Approximately 1.50 M > Touch Less On/off Switch And Electronic Control Box Incorporated In Base Or Spring Loaded Articulating Arm Power Supply: > -power Input To Be 220 Vac (single Phase) / 60hz As Appropriate Fitted With > Philippine Standard Plug > -power Consumption, Approximately 35 Watts Dimensions: > -weight: Total Mobile Stand: Approximately 5.78 Kg. > -height: Total Mobile Stand: Approximately 150.0 Cm (including Luminaire And Control Box) > Non-removable Doh Logo And The Words “for Ambulance Use Only” Must Be Marked On The Visible Part Of The Equipment · Aneroid Sphygmomanometer (mounted On The Ambulance Wall On The Head Side Of The Patient) > The Sphygmomanometer Is Composed Of Cloth Cuff Containing An Inflatable Bag (adult-25 Cm To 35 Cm) > Connected Via A Tube To A Flexible Bulb With Valve And Integrated Manometer Needle Gauge. > Latex And Mercury Free. > Bp Cuffs Are Anti-microbial Treated. > The Adult (25 Cm To 35 Cm) Cuff With Double Velcro Fastening, Enabling It To Be Adjusted To Fit Tightly > Around The Arm. > The Cuff Is Washable, Very Strong And Reinforced At Both Ends. > The Bag Is Inflated By Means Of The Flexible Bulb Connected Via A Tube (length Approximately 60 Cm, > Flexible And With Reliable Quick Connector) > The Quick Connector Can Easily Be Connected To All Types Of Inflation Bulbs > Inflation Bulb With Integrated Manometer Needle Gauge > Dial Graduated Up To 300 Mmhg Aneroid Instrument Mounted At A 20º Angle For Ease Of Viewing Clinical Sphygmomanometer For Desk Type, With Pressure Release Valve > Pressure Gauge To Allow Reading Of Pressure To 2mmhg Accuracy > Gauge Body To Allow Recalibration Of Readings, Yet In Normal Operation Be Sealed And Secure > Plastic Manometer With Chrome Plated Steel Bracket > Non-removable Doh Logo And The Words “for Ambulance Use Only” Must Be Marked On The Visible Part Of The Equipment · Folding Stretcher > Length: At Least 1900 Mm > Width: At Least 530 Mm > Loading Capacity: At Least 120 Kg > The Stretcher Must Have A Quick Release Patient Restrain System > Frame Material: High Grade Aluminum > Frame Must Be Made Of Sturdy Lightweight, Non-twisting Construction And With Rubber Handles > Stretcher Bed Material Must Be Washable > Non-removable Doh Logo And The Words “for Ambulance Use Only” Must Be Marked On The Visible Part Of The Equipment · Scoop Stretcher > Length: At Least 200 Cm > Adjustable Length > Width: At Least 42 Cm > Loading Capacity: At Least 150 Kg > The Stretcher Must Have At Least Three (3) Quick Release Patient Restrain System > Frame Material: High Grade Aluminum > Non-removable Doh Logo And The Words “for Ambulance Use Only” Must Be Marked On The Visible Part Of The Equipment · Heavy Duty Stethoscopes (dual) > Easy To Dismantle, Clean, And Disinfect. > Double Cup, Dual-use (adult And Pediatric Auscultation) In Stainless Steel Or Chromed Brass. > Adult Diaphragm: Approximately 43mm > Bell Diameter: Approximately 32mm > Y Tube Treated Rubber With Large Diameter: Approximately 10 Mm > Arms: Stainless Steel Or Chrome Brass Or Aerospace Alloy, With Spring Treated To Give Lasting Spring And Maximum Reliability And Comfort. > Removable Plastic/rubber Ear-pieces. > Supplied With Spare Diaphragms Or Diaphragm Membrane, Y Tube And A Pair Of Ear-pieces > Environmental Factors: > The Unit Shall Be Capable Of Being Stored Continuously In Ambient Temperature Of 0 - 50 ⁰c And Relative Humidity Of 15-90%. > The Unit Shall Be Capable Of Operating In Ambient Temperature Of 20-30 ⁰c And Relative Humidity Of Less Than 70%. > Non-removable Doh Logo And The Words “for Ambulance Use Only” Must Be Marked On The Visible Part Of The Container Box · Non-contact Thermometer > Measuring Scale: Degree Celsius > Lcd Or Led Display With At Least Three (3) Digit Measurement Display > Components Must Have No Glass And Mercury Materials > Measurement Range: 34°c To 42°c Or Wider Range. > Beep Sound Upon Measurement > Switch Off Automatically When Not In Use. > Battery Operated. > With Low Battery Indicator > Non-removable Doh Logo And The Words “for Ambulance Use Only” Must Be Marked On The Visible Part Of The Equipment · Blood-glucose Meter With Strip > Hand Held Meter > No Routine Maintenance Reading Range/linearity From 20 To 600 Mg/dl > Maximum Reading Time Of Less Than 10 Seconds > Use Of Electrochemical Technology > Use A Minimum Blood Sample Of Less Than 1.5µl > Lcd Display > Measuring Unit In Mg/dl. > Wide Operating Temperature > A Minimum Memory Of 50 Test Results > Should Have Easy Code Entry Technique > Battery Should Be Replaceable Without Using Any Tools > Should Have Facility To Ensure Accuracy Of Measurements. > Should Be Supplied With Three Types Of Control Solutions Of Each At Least 3 Ml > Item Should Have Data Transfer Facility Through Usb Device Or Blue Tooth > The Unit Should Be Cleanable And Sterilizable With Alcohol · Glucose Strips > Should Be Able To Use Capillary Blood Samples. > Should Have A Minimum 4 Months Shelf Life After Opening The Strip Vial. > All Strips Should Have At Least One Year Expiry Date From The Date Of Supply. > Minimum Of 10 Strips, 10 Lancets, And 1 Lancing Device Should Be Supplied Along With The Equipment. > Strips Should Be Available In The Local Market. Power Requirements > Shall Be Battery Operated 3-volt Lithium Ion Cell Battery Or 2 X (aaa) Alkaline Battery. Battery Should Be Supplied With Item And Should Last At Least 1000 Tests. > Non-removable Doh Logo And The Words “for Ambulance Use Only” Must Be Marked On The Visible Part Of The Equipment · Manual Resuscitators For Adult > Resuscitator To Ventilate Adult (body Weight Over 30kg) > Resuscitator Operated By Hand > Ventilation With Ambient Air > Resuscitator Shall Be Easy, To Disassemble And Reassemble, To Clean And Disinfect, And Be Autoclavable. > All Parts Must Be Manufactured From High-strength, Long-life Materials And Require No Special Maintenance Or Storage Conditions. Resuscitator Shall Be Supplied As A Complete Set With: > Compressible Self-refilling Ventilation Bag, Capacity: 1500-2000 Ml > Non-rebreathing Patient Valve With Or Without Pressure Limiting Valve, Patient Connector Outside/inside Diameter (od/id): 22/15 Mm > Inlet Valve With Nipple For 02 Tubing > Oxygen Reservoir Bag Complete, Capacity: 2000-2600 Ml > Masks, Transparent, In 3 Sizes: > 1 Mask, Face Shape Type, Size Adult Small/teenager > 1 Mask, Face Shape Type, Size Adult Medium > 1 Mask, Face Shape Type, Size Adult Large Resuscitator Supplied In A Box As A Complete Set, With Clear Instructions / Diagrams For Use Covering The Technical Performances, The Use And The Maintenance Of The Resuscitator And Assembly In English Language > Materials: Latex-free > Compressible Self-refilling Ventilation Bag: Silicone Rubber, > Non-rebreathing Patient Valve With Pressure Limiting Valve: Polycarbonate/polysulfone/silicone, > Inlet Valve With Nipple For O2 Tubing: Polycarbonate/polysulfone/silicone, > Oxygen Reservoir Bag: Plastic > Masks: Transparent Silicone Rubber. Standards, Safety And Training: > Should Be Fda, Ce, And Ul Approved Product > Conforming To International Standards: Iso, Ce Certification, Fda > Non-removable Doh Logo And The Words “for Ambulance Use Only” Must Be Marked On The Visible Part Of The Equipment Or Container · Manual Resuscitators For Neonate/infant > Resuscitator To Ventilate Preterm, Newborn, Small Infant (body Weight 0-7 Kg) > Resuscitator Operated By Hand > Ventilation With Ambient Air > Resuscitator Shall Be Easy, To Disassemble And Reassemble, To Clean And Disinfect, And Be Autoclavable. > All Parts Must Be Manufactured From High-strength, Long-life Materials And Require No Special Maintenance Or Storage Conditions. Resuscitator Shall Be Supplied As A Complete Set With: > Compressible Self-refilling Ventilation Bag, Capacity: 200-250ml > Non-rebreathing Patient Valve With Pressure Limiting Valve, 40± 5 Cmh2o, Patient Connector Outside/inside Diameter (od/id): 22/15mm, > Inlet Valve With Nipple For 02 Tubing > Masks, Transparent, In 3 Sizes: > 1 Mask, One Piece, Round Shape Type, Size Preterm > 1 Mask, One Piece, Round Shape Type, Size Newborn > 1 Mask, One Piece, Round Shape Type, Size Infant Small > Resuscitator Supplied In A Box As A Complete Set, With Clear Instructions / Diagrams For Use Covering The Technical Performances, The Use And The Maintenance Of The Resuscitator And Assembly In English Language > Materials: Latex-free > Compressible Self-refilling Ventilation Bag: Silicone Rubber > Non-rebreathing Patient Valve With Pressure Limiting Valve: Polycarbonate/polysulfone/silicone > Inlet Valve With Nipple For O2 Tubing: Polycarbonate/polysulfone/silicone > Masks: Transparent Silicone Rubber Standards, Safety And Training: > Should Be Fda, Ce, And Ul Approved Product > Conforming To International Standards: Iso, Ce Certification, Fda Non-removable Doh Logo And The Words “for Ambulance Use Only” Must Be Marked On The Visible Part Of The Equipment Or Container Manual Resuscitators For Pedia (child) > Resuscitator To Ventilate Child (body Weight 7-30 Kg) > Resuscitator Operated By Hand > Ventilation With Ambient Air > Resuscitator Shall Be Easy, To Disassemble And Reassemble, To Clean And Disinfect, And Be Autoclavable. > All Parts Must Be Manufactured From High-strength, Long-life Materials And Require No Special Maintenance Or Storage Conditions. > Compressible Self-refilling Ventilation Bag, Capacity: 500-700 Ml > Non-rebreathing Patient Valve With Pressure Limiting Valve, 40 ±5 Cmh2o, Patient Connector Outside/inside Diameter (od/id): 22/15 Mm > Inlet Valve With Nipple For 02 Tubing > Oxygen Reservoir Bag Complete, Capacity: 2000-2600 Ml > Masks, Transparent, In 3 Sizes: · 1 Mask, Round Shape Type, Size Child Small · 1 Mask, Round Shape Type, Size Child Medium · 1 Mask, Face Shape Type, Size Child Large > Resuscitator Supplied In A Box As A Complete Set, With Clear Instructions / Diagrams For Use Covering The Technical Performances, The Use And The Maintenance Of The Resuscitator And Assembly In English Language > Materials: Latex-free > Compressible Self-refilling Ventilation Bag: Silicone Rubber > Non-rebreathing Patient Valve With Pressure Limiting Valve: Polycarbonate/polysulfone/silicone, > Inlet Valve With Nipple For O2 Tubing: Polycarbonate/polysulfone/silicone, > Oxygen Reservoir Bag: Plastic > Masks: Transparent Silicone Rubber · Oxygen Cylinder With Oxygen Therapy Set > At Least 20 Pounds Capacity > Must Be Color Green > Oxygen Therapy Set · Gauge Reading: 1,800 Psi Or Higher · Flowmeter: 0 To 15 Li/min · Humidifier Bottle: Hard Plastic, Capacity: 200ml To 300ml · Accessories: Mouth Piece, Tubing, Open Wrench For Installing The Therapy Set To The Cylinder · The Cylinder Must Be Placed In A Holder Mounted On The Head Side Of The Patient · Non-removable Doh Logo And The Words “for Ambulance Use Only” Must Be Marked On The Visible Part Of The Equipment · Laryngoscopes Set > Constituted Of A Large Hollow, Cylindrical, Slightly Ribbed Handle And A Set Tongue Depressor In Fiber Optic. > The Handle Is Made Of Fiber Optic Led Light > The Handle Can Be Opened At One End To Insert Two Type C Alkaline Battery > The Other End Has A Stud Contact Which Fits The Various Sizes And Types Of Depressors > The Set Of Autoclavable Depressors Includes: A. 4 Curved Depressors, Macintosh Type: No. 1: Approximately 66 Mm Length No. 2: Approximately 85 Mm Length No. 3: Approximately 105 Mm Length No. 4: Approximately 140 Mm Length B. 5 Straight Depressors, Miller Type: No. 0: Approximately 56 Mm No. 1: Approximately 82 Mm No. 2: Approximately 135 Mm No. 3: Approximately 175 Mm No. 4: Approximately 185 Mm > Contained In Suitable Protective Plastic Box Or Vinyl Sturdy Padding Case > Battery Compartment (if Reusable) To Be Sealed Against Liquid Ingress, Yet Easily Opened > On/off Switch To Be Robust And Easy To Use > Non-removable Doh Logo And The Words “for Ambulance Use Only” Must Be Marked On The Visible Part Of The Container Box · Immobilization Devices A) Cervical Collars I. Rigid For Children Ages 2 Years Or Older Ii. Child And Adult Sizes (small, Medium, Large) B) Head Immobilization Device (not Sand Bags): Firm Padding Or Commercial Device C) Lower Extremity (femur) Traction Devices I. Limb-support Slings Ii. Padded Ankle Hitch Iii. Padded Pelvic Support Iv. Traction Strap (adult & Child Sizes) D) Upper And Lower Extremity Immobilization Devices I. Joint-above And Joint-below Fracture (sizes Appropriate For Adults And Children) Ii. Rigid- Support Constructed With Appropriate Material (cardboard, Metal, Pneumatic, Vacuum, Wood Or Plastic) – Various Sizes E) At Least 2 Pieces - Resistant Straps Or Cravats · Delivery Set All Instruments Must Be Surgical Grade Stainless Steel Material With ± 0.4 Inch Measurement Tolerance > 1 Pc. Sponge Holding Forceps, Rampley 9.5" > 1 Pc. Kidney Dish 10" > 1 Pc. Bowl 200mm > 1 Pc. Umbilical Scissors, American, Straight 4.5" > 1 Pc. Needle Holder Mayo Hegar Straight 6.5" > 1 Pc. Episiotomy Scissors 14.5 Cm > 1 Pc. Cusco Vaginal Speculum Medium > 1 Pc. Hartmann Mosquito Artery Forceps Straight 120mm > 1 Pc. Metal Catheter > 1 Pc. Uterine Curette > 1 Pc. Treves Dissecting Forceps, Plain, 200mm > 1 Pc. Spencerwells Artery Forceps Curved 6" > 1 Pc. Kocher Artery Forceps, Toothed Straight 6" Non-removable Doh Logo And The Words “for Ambulance Use Only” Must Be Marked On The Visible Part Of The Instrument Container Box. · Patient Monitor > Atleast 10 Inches Color Tft Led Display > 800 X 600 Pixels Resolution > Maximum Display Of 11 Channels; Auto Channel Height Adjustment Function > Lightweight & Ergonomic Design > Parameters: 3/5 Lead Ecg, Hr, Resp, Nbp, Spo2, Pr, Temp > With St Segment Analysis And 21 Calls Of Arrhythmia > Fast Spo2 Technology With Anti-motion And Low Perfusion Performance > Navigation Wheel For Information Input And Screen Navigation > Backlit Function Buttons For Quick Access To Key Functions > Bed-to-bed Overview Function For Up To 32 Monitors Without Central Monitoring System > Bi-directional Communication Via Lan Networking To A Central Monitoring System > Standard Hl7 Output > Fan-less Design To Reduce Dust Deposits > Applications From Neonate To Adult > With Oxycrg & Minitrend > With Big Number Screen, Dynamic Trend Screen, & Ocrg Screen > 4 User-defined Layout > Timing Clock Configurable From 5-30mins > 1,600 Sets Nbp Table > 1,200-hour Trend Graph Of All Parameters (with Data Manager Function) > 120-minute Full Disclosure Ecg 1 Waveform Review (with Data Manager Function) > 200 Sets Alarm Events & 200 Sets Arrhythmia Events > With Drug Calculation > With Hr Variation & Dynamic Blood Pressure Analysis > Rechargeable Lithium Ion Battery With 2.5 Hrs Of Operation > With Built-in 3-channel Recorder > Standard External Interface Available: Ecg Analog Output, Vga Output, Nurse Call, Lan, Usb > Patient Data Export Using A Usb Data Manager > Net Weight: Approximately 4.2kg Vii. Other Equipment And Accessories Note: The Items Below (except The Iv Holder) Must Be Marked With Non-removable Doh Logo And The Words “for Ambulances Use Only” On The Visible Part Of The Equipment. > Fire Extinguisher (rating 2a10bc), Five (5) Pounds, With Holder Mounted On The Ambulance Floor. > Heavy Duty Led Flashlight With At Least 1,000 Lumens Of Brightness With Extra Batteries. Iv Holder (mounted On The Ambulance Wall Head Side Of The Patient). > Digital Clock With At Least 4 Inch Display Mounted On The Ambulance Wall. > Air Purifier With Multi-stage Air Filters (pre-filter, Hepa, Carbon) And With Uv Light. > Garbage Container At Least 3 Liter Capacity And Made Of Fiberglass Reinforced Plastic Or Acrylonitrile Butadiene Styrene (abs) Plastic Material And With Lid Cover. The Container Must Be Properly Labelled And Must Be Mounted On The Ambulance Floor. > Sharps Container With Sliding Lid And At Least 1 Liter Capacity, Made Of Fiberglass Reinforced Plastic Or Abs Plastic Material. The Container Must Be Mounted On The Ambulance Wall. I. Other Requirments To Be Submitted During The Bid Opening 1. Product Brochure(s) Or Technical Data Sheet(s) In Hard And Soft Copies Showing The Technical Specifications Of The Following In English Language: A) Ambulance Vehicle B) Emergency Lights, Siren And Public Address C) Ambulance Stretcher D) Automatic External Defibrillator E) Nebulizer F) Examining Light G) Aneroid Sphygmomanometer H) Folding Stretcher I) Scoop Stretcher J) Heavy Duty Stethoscopes K) Non-contact Thermometer L) Blood Glucose Meter M) Manual Resuscitators N) Suction Machine O) Oxygen Therapy Set P) Laryngoscopes Set Q) Delivery Set R) Air Purifier S) Patient Monitor · Valid Marketing Authorization, Registration Approval Or Free Sale Certificate For The Automatic External Defibrillator Issued By The Health Authority In The Country Of Origin. · Valid Certificate Of Distributorship (as First Tier Distributor) Issued By The Foreign Manufacturers Or Local Distributors Of The Medical Equipment And Instruments Authorizing The Bidder To Sell/distribute Their Products. · Notarized Certificate From The Bidder: That The Brands Of The Medical Equipment And Instruments Have Been In The Local And/or International Market For At Least Ten (10) Years. > That Medical Equipment And Instruments Are Brand New, Unused, Not Discontinued Models And Were Not Subjected To Any Product Recall. · Bidder’s Valid And Current License To Operate (lto) As A Medical Device Distributor Issued By The Philippine Food And Drug Administration. · Valid And Current Certification Of Product Registration (cpr) For The Thermometer, Lancets In The Blood-glucose Meter And Manual Resuscitator Issued By The Philippine Food And Drug Administration (pfda) · Notarized Certificate From The Manufacturer Or Local Dealer Of The Ambulance/vehicle: > That The Manufacturer Has Been Manufacturing Vehicles With Diesel Engines For The Past Twenty Five (25) Years. > That The Ambulance/vehicle Is Brand New, Unused, Not A Discontinued Model And Was Not Subjected To Any Product Recall. · Proofs (such As Sales Invoice) That The Brand Of The Vehicle Has Already Been Sold In The Country As An Ambulance. Requirement/s If Declared The Lowest/single Calculated Bid · Site Inspection To The Bidder’s Facility To Verify/validate The Capability And Capacity Of The Bidder To Fabricate The Ambulances As Well As Sample Unit With Complete Medical Accessories. The Inspection Shall Be Conducted By The Procuring Entity Technical Working Group. This Requirement Is Not Applicable If The Facility Is Located Outside The Philippines. · Motor Vehicle Service Center Should Be Located In Each Province Namely Cebu, Bohol, & Negros Oriental In Order For The Recipient Facility To Have Easy Access During Preventive Maintenance. Requirements If Awarded The Contract · The Supplier Shall Provide Orientation/training On The Use And Maintenance Of The Ambulance, Medical Equipment And Instruments On A Schedule To Be Agreed Upon By Procuring Entity And The Winning Bidder. · The Supplier Shall Submit/provide The Following To The End User: > Operator’s Manual In English Language For The Ambulance, Medical Equipment And Instruments. > Certification Of Inclusive Preventive Maintenance Services From 10 Kilometer Up To 40 Kilometer With An Interval Of 10,000kms Or 6 Months Whichever Comes First At Any Manufacturer’s Service Center Branches In Central Visayas. > Warranty Certificate For Three (3) Years On Parts And Services For The Ambulance. The Manufacturer/dealer Shall Either Repair Or Replace Any Item Or Part In The Ambulance That Is Found To Be Defective In Material Or In Workmanship Under Normal Use. The Warranty Period Shall Commence From The Date Of Acceptance By The End-user After Testing And Commissioning. The Warranty Certificate Shall Include The Following: · That The Warranty For The Vehicle Shall Not Be Affected In Case A Change Of Dealer Occurs. That If The Ambulance Is Unable To Return To The Service Center During The Warranty Period, The Manufacturer/dealer Shall Provide Mechanics And/or Technicians That Can Perform On-site Service And Maintenance, Provided That The End User Will Shoulder The Travel Expenses. · Warranty Certificate For Two (2) Years On Parts And Services For Medical Equipment, Instruments And Ambulance Accessories. The Supplier Shall Either Repair Or Replace Any Item Or Part In The Said Equipment That Is Found To Be Defective In Material Or In Workmanship Under Normal Use. The Warranty Period Shall Commence From The Date Of Acceptance By The End-user After Testing And Commissioning. The Warranty Certificate Shall Include The Following: > The Bidder Shall Conduct The Necessary Corrective Maintenance Within Fifteen (15) Calendar Days Upon Notification Of Equipment Breakdown From The End-user. > The Bidder Shall Have The Primary Responsibility And Accountability To Ensure That In Case Of Defects, The Vehicle, Equipment, Instruments And/or Peripherals Are Appropriately Repaired Or Replaced And Shall Be In Good Working Condition Thereafter. · At Least Three (3) Years Validity Of The Vehicle From Land Transportation Office Region 7 (lto Ro7) Registration With Red Plate. This Is To Allow Easy Accessibility By The Recipient Lgus For The Processing And Transfer Of The Documents. · Third Party Liability (tpl) Vehicle Insurance For One (1) Year And Comprehensive Gsis Vehicle Insurance For One (1) Year. · Delivery > Delivery Schedule: Within 90 Calendar Days Upon The Receipt Of Purchase Order > Upon Delivery, Each Ambulance Shall Undergo Preliminary Physical Inspection By The Inspection Team Of The Procuring Entity To Ascertain The Physical Condition And Acceptability Of The Units. All Medical Equipment, Instruments, Ambulance Accessories And Peripherals Must Be Functioning And Must Have No Physical Damage. > All Land Ambulance Units Shall Be Filled Up With Crude Diesel At Full Tank Capacity Upon Delivery. · Terms And Conditions: > Supplier Must Not Have Any Pending Or Incomplete Delivery, Installation, Training And Demonstration Beyond The Delivery Period Indicated In The Purchase Order With Any Existing Doh-cvchd Projects. > The Supplier Must Coordinate With The Equipment Unit Head And Supply Officer On The Schedule Of The Delivery, Completion Of Training & Demonstration In Order To Facilitate Inspection Of The Doh Cvchd Inspection Team. Payment Will Only Be Made After Delivery And Installation. > Demonstration, Training & Completion Of The Accessories And Equipment Should Be Within 5 Days After The Delivery Of The Equipment. O *recipient Facility Shall Sign The Ptr Only If The Supplier Fully Complied With The Above The Supplier Shall Conduct Comprehensive Demonstration & Training For Staff And Support Services Till Familiarity With The Unit. A Copy Of The Certificate Of Training And Documentation During The Training Session Shall Be Provided To The End Users And Supply Office.

Details: Description Invitation To Bid For The Rebidding Of Provision Of Labor, Materials, Equipment Rental And Other Incidentals Needed For The Construction Of Feed Mill Processing Facility In Brgy. #40 Buyon, Bacarra, Ilocos Norte 1. The Department Of Agriculture - Regional Field Office 1 (da-rfo 1), Through The Gaa Fy 2024 Intends To Apply The Sum Of Ten Million Pesos (php10,000,000.00) Being The Approved Budget For The Contract (abc) To Payment Under The Contract For The Rebidding Of Provision Of Labor, Materials, Equipment Rental And Other Incidentals Needed For The Construction Of Feed Mill Processing Facility In Brgy. #40 Buyon, Bacarra, Ilocos Norte With Project Identification Number Da-rfo-1-2024-infra-035-r. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. 2. The Da-rfo 1 Now Invites Bids For The Above Procurement Project With The Following Details And Specifications: Details And Specifications Project Location: Brgy. #40 Buyon, Bacarra, Ilocos Norte Project Description: Construction Of Feed Mill Processing Facility With A Dimension Of 15m X 10m Component 1: Building Scope Of Work: Description Qty Unit I. Mobilization And Demobilization 1.00 L.s. Ii. Permits And Clearance 1.00 L.s Iii. Project Billboard/sign Board 1.00 L.s Iv. Safety And Health 1.00 L.s V. Construction Of Temporary Facility 12.00 Sq.m. Vi. Clearing And Grubbing 100.00 Sq.m. Vii. Earthworks 99.66 Cu.m. Viii. Rsb Works 2,429.48 Kgs Ix. Forms Works 420.00 Bd.ft. X. Concrete Works 30.00 Cu.m. Xi. Masonry Works 30.00 Sq.m. Xii. Iron Works 7,619.13 Kgs Xiii. Painting Works 100.00 Sq.m. Xiv. Roofing And Siding Works 448.44 L.m Xv. Windows And Doors 29.50 Sq.m. Xvi. Plumbing Works 1.00 Lot Xvii. Electrical Works 15.00 Outlet Xviii. Da Logo 1.00 Lot Minimum Technical Personnel Required: • 1 Project Engineer • 1 Foreman • 2 Skilled Workers • 6 Unskilled Workers Minimum Equipment Required: • 1 Concrete Mixer, One-bagger • 1 Angle Grinder • 1 Cut-off Machine • 1 Bar Cutter • 1 Welding Machine • 1 Generator Set • 1 Electrical Drill Component 2: Machinery All Components Shall Be Of The Same Brand, Brand New And Not Rebranded/renamed. 1. Built A. Compact B. System (per Component) 2. Crusher Function: Crush The Raw Materials To Powder Capacity: 100kg/hr Primemover: 4kw, Electric Motor, Single Phase 3. Mixer Function: Can Mix Materials Uniformly Capacity: 100kg/batch Where One Batch Needs 5-10mins Primemover: 4kw Electric Motor, Single Phase 4. Screw Conveyor Function: Use To Lift And Transfer Powder Or Raw Materials To The Mixer. Primemover: 2.2kw Electric Motor, Single Phase Capacity: 500 Kg/hr 5. Feed Pellet Machine Primemover:15kw, Electric Motor, 3-phase Capacity: 300 Kg/hr 6. Belt Conveyor Capacity: 200 Kg/hr Power:2.2kw, Electric Motor, Single Phase 7. Cooler And Dust Collector Function: Use To Cool The Finished Product Capacity: 200kg/hr Primemover (cooler): 0.75 Kw Primemover (dust Collector): 2.2 Kw 8. Bag Sewing Machine 9. With 2 Tons Silo Other Requirements For The Supplier Of The Goods/machinery: * Brochures/pictures, Operator’s Manual * System Testing Shall Be Conducted By Amtec After Complete Installation * Valid Permit To Operate Issued By Bafe (all Machinery Components Must Be Stated As Product Lines) And Certificate Of Namdac Accreditation Issued By Pcaf * Certificate Of Company-owned/affiliated Service Center Within The Region And Service Center Must Have A Permit To Operate Issued By Bafe * Notarized Affidavit Of Undertaking For After Sales Service That Supplier Must Render Within 72 Hours Upon Receipt Of Notice From The Recipients/ Procuring Entity * Certificate Of Availability Of Spare Parts Of The Brand/model Being Offered Within The Region To Be Issued By The Distributor/manufacturer/affiliated Service Center * Notarized Certificate Of Stock Allocation To Be Submitted During The Bid Opening Issued By The Distributor/dealer/importer Specifying The Name Of Project To Da Rfo 1 * Certificate To Conduct On-site Technical Briefing For Operators On Operation, Maintenance, And/or Repair Of The Supplied Goods By The Supplier With The Following Compatible Accessories: 1. All Components Should Be Provided With Compatible Electric Motor - Connecting Wires And Cables Shall Conform To Electrical Code Of The Philippines - Moisture And Dust Proof - With Thermal Protection Device 2. Control Panel - Compatible To The Electrical Requirements Of The Feed Milling System - Must Contain Mimic Flow Of Operation - With Basic Safety Cut-off Features Including Emergency Shutdown Button - With On-off Push Button Switch And Individual Circuit Breaker For Each Motor - Dust Proof 3. One (1) Unit Weighing Scale - Mechanical Type - Capacity: 1 Ton (minimum) - Readability: 0.5 Kg 4. With Safety And Ease Of Operation Features - Path Walks - Markings/direction/borders - Provision Of Harness - Moving And Rotating Components Of The Feed Mill Must Be Covered - Two (2) Units Fire Extinguisher For The Control Room And Feed Milling Area * Dry Chemical, Stored Pressure Type, Capacity: 6.80kg, Minimum - Basic Safety Kits 5. With Additional 2 Dies, Shieve And 1 Spare Hammermill Teeth 6. Equipped With Electrical Requirements 7. Compatible Panel Board With Circuit Breakers - The Electrical Wire, Wire Accessories, And Piping/conduit To Connect The Transformer Unit To The Main Distribution Panel Board And To The Control Panel Of The Feed Milling System Shall Be Provided By The Bidder - The Electrical Wires, Panel Board, Circuit Breakers And Piping/conduit Must Be Brand New 8. Appropriate Heavy Duty Tools: Made Of Tempered Steel And Chrome Vanadium - With Heavy Duty Toolbox And Roll Up Tools Holder 9. With Appropriate Mounting Frame - All Component Of The Feed Mill Shall Be Installed With Mounting Frame And Fitted With Brackets 10. All Major Components And Parts Of The Feed Should Be Painted Powder Coated. For Mounting Frames, Path Walks And Catwalks Should Be Painted Finish, With Rust-proofing Primer And Final Paint Color 11. With Appropriate Silent Type Generator Set 12. With Converter (from Single Phase Power To 3-phase Power) Completion Of The Works Is One Hundred Twenty (120) Calendar Days For Infrastructure Component And Forty (40) Calendar Days For The Machinery Component Upon The Completion Of Infra Component. Bidders Should Have Completed A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii. (instructions To Bidders). 3. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using A Non-discretionary “pass/fail” Criterion As Specified In The Implementing Rules And Regulations (irr) Of Republic Act (ra) 9184. Bidding Is Restricted To Filipino Citizens/sole Proprietorships, Partnerships, Or Organizations With At Least Seventy-five Percent (75%) Interest Or Outstanding Capital Stock Belonging To Citizens Of The Philippines. 4. Prospective Bidders May Obtain Further Information From And Inspect The Bidding Documents At The Address Given Below During Office Hours At 8:00 Am To 5:00 Pm, Monday To Friday. Department Of Agriculture - Regional Field Office 1 Aguila Rd., Sevilla, City Of San Fernando, La Union 5. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders From December 2-23, 2024 From The Address Given And Websites Below And Upon Payment Of The Applicable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb, In The Amount Of Php10,000.00. The Procuring Entity Shall Allow The Bidder To Present Its Proof Of Payment For The Fees In Person, By Facsimile, Or Through Electronic Means. 6. The Da-rfo 1 Will Hold A Pre-bid Conference On 09 December 2024, 3:00 Pm At Da-rfo 1, 5th Floor Conference Room, Aguila Road, Sevilla, City Of San Fernando, La Union, Which Shall Be Open To Prospective Bidders. 7. Bids Must Be Duly Received By The Bac Secretariat Through Manual Submission At The Office Address Indicated Above On Or Before 23 December 2024, 3:00 Pm. Late Bids Shall Not Be Accepted. 8. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 14. 9. Bid Opening Shall Be On 23 December 2024, 3:00 Pm At Da-rfo 1, 5th Floor Conference Room, Aguila Road, Sevilla, City Of San Fernando, La Union. Bids Will Be Opened In The Presence Of The Bidders Or Their Authorized Representatives. 10. Additional Instructions To Bidders: A. The Bidders Or Their Duly Authorized Representatives May Attend The Bid Opening; B. In Case A Representative Will Be Attending The Bid Opening, A Special Power Of Attorney (spa), Secretary’s Certificate, Board Resolution Or Any Other Forms Of Authorization (notarized), As The Case May Be, Together With The Company-issued Identification Card Or Any Valid Id Must Be Presented Upon Submission Of The Bid Proposal At The Bac Secretariat. The Name/title Of The Project Must Be Indicated In The Authorization Or Spa; C. Each Bidder Shall Submit One Copy Of The First And Second Components Of Its Bid. Bidders Shall Submit Their Bids With Proper Index Tabbing Using The Forms Specified In The Bidding Documents In Two (2) Separate Sealed Bid Envelopes, And Which Shall Be Submitted Simultaneously; The First Component Which Is The Technical Eligibility Requirements Must Be Soft-bound, Marked With The Name Of The Contract And Its Ib No., Name And Address Of The Bidder, And Enclosed In An Envelope, Sealed With Signature And Marked With The Name Of The Contract, Name And Address Of The Bidder, Addressed To The Bids And Awards Committee (bac) Da Rfo-1 City Of San Fernando, La Union, The Specific Identification No. And The Warning “do Not Open Before…” The Date And Time For The Bid Opening. The Second Component Being The Financial Requirements May Be Soft-bound/fastened In A Folder, Marked With The Name Of The Contract And Its Ib No., Name And Address Of The Bidder, And Enclosed In An Envelope, Sealed With Signature And Marked With The Name Of The Contract, Name And Address Of The Bidder, Addressed To The Bids And Awards Committee (bac) Da Rfo-1 City Of San Fernando, La Union, The Specific Identification No. And The Warning “do Not Open Before…” The Date And Time For The Bid Opening. The Technical And Financial Requirement Each In Separate Envelopes, Shall Be Enclosed In A Mother Envelope With The Same Sealing And Markings. Non-compliance With Index Tabbings Shall Not Be A Ground For Outright Disqualification Or Declaration Of Ineligibility. The Improper Index Tabbings Must Be Duly Acknowledged By The Bidder/representative And Be Subject To The Bid Evaluation And Post-qualification Of The Technical Working Group (twg) As To Their Substance. D. All Documents In The Financial Requirements Envelope Must Be Duly Signed And/or Initialed, As Needed, By The Bidder/authorized Representative On Each And Every Page Thereof. E. The Technical Specifications Of The Project (as Part Of Tab F - Project Requirements) Must Be Duly Signed/countersigned And Sealed By A Licensed Agricultural And Biosystems Engineer In Accordance With Republic Act 8559 Or Republic Act 10915. 11. The Da-rfo 1 Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And Section 41 Of The 2016 Revised Irr Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 12. For Further Information, Please Refer To: Dennis I. Tactac, Abe Chairperson, Bids And Awards Committee Department Of Agriculture - Regional Field Office 1 Aguila Road, Sevilla, City Of San Fernando, La Union Tel. No.:(072) 242/1045-46, Ext. 07 E-mail Add: Bacsec@ilocos.da.gov.ph 13. For Downloading Of Bidding Documents, You May Visit The Following Websites: Da-rfo1 Website: Https://ilocos.da.gov.ph/ Philgeps Website: Https://www.philgeps.gov.ph/ November 29, 2024 Approved By: (sgd.) Gilbert D. Rabara, Dvm Vice-chairperson, Bids And Awards Committee Invitation To Bid Identification No. Da-rfo 1-2024-infra-035-r

Details: Description Invitation To Bid For Fy 2024 Procurement And Delivery Of Learning Tools And Equipment For Technical Vocational Livelihood (tvl) Project Identification No.: Pb-albaygoods-24-23 1. The Department Of Education, Schools Division Office Of Albay, Through The General Appropriations Act Of 2024 Intends To Apply The Sum Of Philippine Pesos Twenty Two Million Six Hundred Twenty Three Thousand Nine (php 22,623,009.00) Only Being The Abc As Payment For The Above-mentioned Contract. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. Unit Of Measure Quantity Item Description Estimated Unit Cost (php) Estimated Cost (php) Fy 2024 Procurement And Delivery Of Learning Tools And Equipment For Technical Vocational Livelihood (tvl) 19 Pc Air Compressor With Airbrush Cake Decorating Set. Type L Single Cylinder Piston Compressor Body Shape : Cylindrical In Shape Material: Copper, Aluminum Dimension: (l X W X H) 24 Cm X 13 Cm X 17 Cm (minimum) Power Source: 220 Volts Ac, 60 Hz With Power Cord 1.5 Meters Long Minimum With Attachment Standard Male Plug Type A Or Provide An Adopter Plug Power Rating : 1/6 Hp Motor Capacity: Air Pressure Adjustment Range 0 To 57 Psi. Automatic On/off Shutoff Compressor Must Have Oil Filter, Water Trap Filter, Pressure Regulator With Gauge, And With Mounted Airbrush Holder And With Built In Cooling Fans Airbrush Specifications: A) Airbrush Material: Stainless Steel Body; B) Needle Dia.: 0.3 Mm. C) Cup Capacity: 2 Cc (cubic Centimeter); D) Airbrush With A 1/3 Oz. Gravity Fluid Cup; E) Nozzle That Allow To Spray From Hairline Up To 1 1/2 Inches Wide; F) Operating Pressure: 15-57 Psi. G) Rubber Hose Length: 2-meter (minimum) H.) Air Flow: 20 Liters/min. Package Content; 1 Pc Air Compressor, 1 Set Air Brush Kit With Case, 5 Ft- Rubber/vinyl Hose, 5 Pcs Cleaning Brushes In Different Width, Tools And User’s Manual. Comes With User's Manual That Content: Operation Guide, Maintenance/ Troubleshooting Procedure And List Of Parts. 10,000.02 190,000.38 114 Pc Beater. Body Shape: Circular Handheld Mixer Materials: Stainless Steel With Plastic Grip Dimension: L-28 Cm X Width-7 Cm (minimum) Twin Beater Designed For Mixing Preferably With Packing Case Smooth Motion Gear And Durable Mechanism Dishwasher Safe And Rust Free 475.00 54,150.00 114 Set Board, Chopping, 6 Color. Type: Food Grade Body Shape: Rectangular Material: Plastic (polypropylene), Food Grade Board Size: Length: 38 Cm (minimum) Width: 30 Cm (minimum) Thickness: 1.27 Cm (minimum) Color-coded For Use With Different Types Of Food, Blue, Red, Yellow, Green, Brown And White, 3,300.00 376,200.00 19 Pc Boiler, Double. Material: Stainless Steel Thickness: 1/16 Inch (1.5 Mm) (minimum) Lid Material: Glass Riveted Handle On Both Side Diameter: 9 1/2 Inches (minimum) Total Height: 9.4 Inches (minimum) Inset Bottom Diameter: 9 Inches (minimum) Inset Top Diameter: 9 Inches (minimum) Capacity: 2 Liters (minimum) Must Be A Set Which Includes One (1) Saucepan, One (1) Boiler, And One (1) Lid With Stainless Steel Handle And Smooth Surfaces With No Sharp Edges 2,465.00 46,835.00 228 Set Bowl, Mixing (6 Pcs/set). Type: Mixing Bowl Set Body Shape: Round Material: Stainless Steel, 0.8 Mm - 1.0 Mm Thick Each Set Must Consist Of The Following Capacities 1 Pc - 0.70 Liter 1 Pc - 1.5 Liters 1 Pc - 3 Liters 1pc - 4 Liters 1pc - 5 Liters 1pc - 8 Liters Light Weight And Easy To Use, Flat Base, Curved Lip Preferably With Packing Case. Dishwasher Safe. 2,440.00 556,320.00 114 Set Cake Pans, Round #4, #6, #8, #10, #12, #14, #16. Type: Round Pan Body Shape: Round Material: Anodized Aluminum Thickness: 1.29 Mm Thick (minimum) Depth: 2 Inches (50.8 Mm) (minimum) Set Must Each Contain The Following Diameter: 1 Pc - 6 Inches (152.4 Mm) Diameter (minimum) 1 Pc - 8 Inches (203.2 Mm) Diameter (minimum) 1 Pc - 10 Inches (254 Mm) Diameter (minimum) 1 Pc - 12 Inches (304.8 Mm)diameter (minimum) 1 Pc - 14 Inches (355.6 Mm) Diameter (minimum) 1 Pc - 16 Inches (406.4 Mm) Diameter (minimum) Preferably Packed (6 Pcs Per Set) Rolled Edge For Better Strength And Smooth Surface With No Sharp Edges The Materials Used Must Be Non-toxic. 3,650.00 416,100.00 114 Pc Cake Stand, With Tier. - Circular With 3 Tier. Hard Plastic, Polypropylene, 4 Mm Thick. The Tier Consists Of The Following Sizes: Tier 1: 18 Cm Diameter (minimum) Tier 2: 25 Cm Diameter (minimum) Tier 3 : 30 Cm Diameter (minimum) Column Diameter: 20 To 30 Mm (solid) Distance Between Tiers: 15 Cm Over-all Length: 30 Cm (minimum) 3,047.33 347,395.62 57 Pc Cake Turn Table. Material: Cast Aluminum Plate And Cast Iron Base Upper Plate: 30 Cm Diameter (minimum) And 1.4 Cm Thickness (minimum)base Dimensions: 18 Cm (minimum); 1.4 Cm Thickness (minimum) Total Height: 10 Cm To 15 Cm 2,500.00 142,500.00 247 Pc Coupler. Body Shape: Tubular Material: Hard Plastic, Polypropylene, Any Bright Color Height: 3cm (minimum) Top Diameter: 1.27 Cm (minimum) Bottom Diameter: 2.54 Cm (minimum) Preferably With Storage Case 265.00 65,455.00 228 Pc Cup, Measuring (for Solid). Type: Measuring Cup Set Body Shape: Round Material: Stainless Steel, 0.7 Mm Thick (minimum) Each Set Contains The Following: 1 Pc - 1 Cup (237 Ml) 1 Pc - 1/2 Cup (118 Ml) 1 Pc - 1/3 Cup (79 Ml) 1 Pc - 1/4 Cup (59 Ml) Handle Dimension: Length-12 Cm X Width-1 Cm (minimum) Measuring Capacity Engraved On The Handle Strip Handles Have Provision For Hanging Preferably With Packing Case Smooth Surfaces And Dishwasher Safe 575.00 131,100.00 228 Pc Cup, Measuring, 250 Ml For Liquid. Type: Clear Glass Cup Body Shape: Round Material: Clear, Non-porous Tempered Glass Capacity: 250 Ml (with 10 Ml Or 50 Ml Increments) With Permanent Graduation Markings Specified Metric And English System Of Measurement With Handle & Spout For Easy Pouring Preferably With Packing Case Food Grade And Safe Use To Microwave, Freezer And Dishwasher 885.00 201,780.00 228 Pc Cup, Measuring, 500ml For Liquid. Type: Clear Glass Cup Body Shape: Round Material: Clear, Non-porous Tempered Glass Capacity: 500 Ml (with 10 Ml Or 50 Ml Increments) With Permanent Graduation Markings Specified Metric And English System Of Measurement With Handle & Spout For Easy Pouring Preferably With Packing Case Food Grade And Safe Use To Microwave, Freeze And Dishwasher 1,150.00 262,200.00 19 Pc Cutter, Dough. Type: Scrapper Body Shape: Straight Blade Material: Stainless Steel Straight Blade With Stainless Steel Handle Blade Dimension: Length : 15 Cm X Width: 11 Cm X Thickness: 1.2 Mm(minimum) Handle Dimension: Length: 15 Cm X Diameter: 3 Cm (minimum) Preferably With Packing Case Food Grade And Dishwasher Safe Design Allows Item To Be Hung For Storage 620.00 11,780.00 114 Pc Cutter, Pie. Type: Pie Cutter Wheel Knife Body Shape: Round Wheel Roller Material: Stailess Steel Overall Length: 19.5 Cm (minimum) Wheel Diameter: 6.5 Cm (minimum) With Hanging Hook At The Tip Of The Handle For Hanging Storage High Quality Food Grade Stainless Steel, High Strength, Good Hardness Preferably With Packing Case Comes With Finger Protection And Not Easily Deformed, Anti-corrosion. Dishwasher Safe. 620.00 70,680.00 114 Pc Flour Sifter, Hand Cranked. Body Shape: Round Shape Material: Stainless Steel Dimension: Diameter: 133.3 Mm (minimum) X Height: 165 Mm (minimum) Thickness: 0.79 Mm (minimum) (body) And Constructed With Stainless Steel Wire Mesh # 30 Bottom Volume Markings Should Be Seen Inside And Outside Of The Sifter Capacity: 5 Cups (1.18 Liter) Spring Action Squeeze Handle Stainless Steel Preferably With A Packing Case. Dishwasher Safe. 500.00 57,000.00 114 Pc Grater. Type: Four-sided Box Grater Body Shape: Box In Shape Material: Stainless Steel Blade And Plastic (polypropylene Handle) Grater Dimensions: Height- 25 Cm X Width-13 Cm X Depth-10 Cm (minimum) Side 1: Large-hole Shredder With 6 Mm Hole Side 2: Slicer Side 3: Small-hole Shredder With 3 Mm Hole Side 4: Grater With Strips About 1.27 Cm To 2.54 Cm Length Preferably With Packing Case. Food Grade & Dishwashing Safe 350.00 39,900.00 114 Pc Knife, Kitchen. Blade Material: Stainless Steel 316. Must Be Branded. 500.00 57,000.00 114 Pc Knife, Pallet. Type: Pallete Knife Body Shape: Offset Blade Blade Material: Stainless Steel 316 Handle Material: Hardwood (smooth Finish) With Rivets Overall Length: 30.5 Cm - 35.6 Cm Total Length: Blade Dimension: Length- 17 Cm X Width-3.8 Cm (minimum) Thickness Of Blade: 1.7 Mm Thick (minimum) Preferably With Packing Case Dishwasher Safe. Must Be Branded. 450.00 51,300.00 114 Pc Ladle, 3 Oz. Material: Stainless Steel Thickness: 1 Mm Thick (minimum) Handle Length: 28 Cm (minimum) Capacity: 3 Oz. (85 Ml) Ladle Type: Round Bottom Hooked Handle Design Allows It To Easily Sit On The Edge Of Pots. Preferably With A Packing Case Dishwasher Safe. Must Be Branded. 300.00 34,200.00 114 Pc Loaf Pan, Big. Type: Loaf Pan Body Shape: Rectangular Material: Anodized Aluminum Thickness: 1.5 Mm - 2 Mm Length: 25.4 Cm (minimum) Width: 12.7 Cm (minimum) Depth: 7.62 Cm (minimum) Preferably With Packing Case Extended Sides For An Easy Grip And Smooth Surfaces With No Sharp Edges Food Grade And Oven Safe. Must Be Branded. 700.00 79,800.00 114 Pc Loaf Pan, Medium. Body Shape: Rectangular Material: Anodized Aluminum Thickness: 1.5 Mm - 2 Mm Length: 22.86 Cm (minimum) Width: 11.43 Cm (minimum) Depth: 6.9 Cm (minimum) Preferably With Packing Case Extended Sides For An Easy Grip And Smooth Surfaces With No Sharp Edges Food Grade & Oven Safe. Must Be Branded. 650.00 74,100.00 114 Pc Loaf Pan, Small. Type: Loaf Pan Body Shape: Rectangular Material: Anodized Aluminum Thickness: 1.5 Mm - 2 Mm Length: 17.78 Cm (minimum) Width: 7.62 Cm (minimum) Depth: 5.48 Cm (minimum) Preferably With Packing Case Extended Sides For An Easy Grip And Smooth Surfaces With No Sharp Edges Food Grade And Oven Safe Must Be Branded. 600.00 68,400.00 114 Pc Muffin Pan, Big. Type: Muffin Pan Body Shape: Rectangular Material: Anodized Aluminum Thickness: 1.5 Mm (minimum) Dimension: Length-36.6 Cm X Width-22.9 Cm X Height-7.6 Cm (minimum) Cup Size: Height- 8.2 Cm X Diameter 8.9 Cm (minimum) Number Of Cups In A Tray: 6 Cup Preferably With Packing Case Extended Sides For An Easy Grip And Smooth Surfaces With No Sharp Edges Food Grade. Must Be Branded. 800.00 91,200.00 114 Pc Muffin Pan, Medium. Type: Muffin Pan Body Shape: Rectangular Material: Anodized Aluminum Thickness: 1.5 Mm (minimum) Dimension: Length-40 Cm X Width-27.9 Cm X Height-2.8 Cm (minimum) Cup Size: Heigth-5.2 Cm X Diameter 6.9 Cm (minimum) Number Of Cups In A Tray: 12 Cup Preferably With Packing Case. Extended Sides For An Easy Grip And Smooth Surfaces With No Sharp Edges Food Grade. Must Be Branded. 700.00 79,800.00 114 Pc Muffin Pan, Small. Type: Muffin Pan Body Shape: Rectangular Material: Anodized Aluminum Thickness: 1.5 Mm (minimum) Dimension: Length 40.6 Cm X Width-25.4 Cm X Height 2.8 Cm (minimum) Cup Size: Heigth-2.5 Cm X Diameter 3.8 Cm (minimum) Number Of Cups In A Tray: 24 Cup Preferably With Packing Case Extended Sides For An Easy Grip And Smooth Surfaces With No Sharp Edges Food Grade. Must Be Branded. 600.00 68,400.00 114 Pc Pie Pan, 10 Inches Diameter. Type: Pie Pan Body Shape: Round Material: Aluminum, 0.81 Mm Thick (minimum) Diameter -10 Inches (254 Mm) Minimum Depth: 1.25 Inches (31.75 Mm) Minimum Coated With Non-stick Coating Materials Preferably With Packing Case Oven Safe To 500°f / 260°c Food Grade Smooth Finish Surfaces Without Sharp Edges Extended Sides For An Easy Grip. Must Be Branded. 525.00 59,850.00 114 Set Pie Pan, #6, #8, #10 (set). Type Pie Pan Body Shape: Round Material: Aluminum, 0.81 Mm Thick (minimum) 1) # 10 Diameter: 10 Inches (254 Mm) Minimum 2) # 8 Diameter: 8 Inches(203 Mm) Minimum) 3) #6 Diameter: 6 Inches (152 Mm) Minimum Depth: 1.5 Inches (38.1 Mm) Minimum Oven Safe To 500°f / 260°c Coated With Non-stick Coating Materials Preferably With Packing Case Food Grade Smooth Finish Surfaces Without Sharp Edges Extended Sides For An Easy Grip. Must Be Branded. 850.00 96,900.00 114 Pc Pillars, Cake. Type: Cake Pillars, Food Grade Body Shape: Tubular Material: Crystal Clear Fiber Plastic Tube Diameter: 2.5 Cm (minimum) Base And Top Diameter: 3.5 Cm (minimum) Height: 13 Cm (minimum). Packed In Four (4) Pcs Per Set The Materials Used Must Be Non-toxic. Must Be Branded 400.00 45,600.00 76 Pc Rectangular Pan, 1 X 8. Type: Rectangular Pan Body Shape: Square Inn Shape Material: Anodized Aluminum Thickness: 1.63 Mm Thick, Minimum Dimensions: Length- 8 Inches X Width- 8 Inches X Height- 1 Inch (minimum) Oven Safe To 500°f / 260°c Preferably With Packing Case Food Grade And Dishwasher Safe. Must Be Branded. 450.00 34,200.00 114 Pc Rolling Pins. Type: Rolling Pins Body Shape: Tubular In Shape Material: Hardwood (solid Wood In Natural Color) Roller Dimensions: 2.5 Inches Diameter X 9.5 Inches Length (minimum) Handle Dimension: 1 Inch Diameter X 4 Inches Length (minimum) Overall Length: 17.5 Inches (minimum) The Wood Rolling Pin Boasts Rust Proof Nylon Bearings For Smooth Rolling Action Smooth Rotation Of The Revolving Barrel Preferably With Packing Case Smooth Surface Finish With No Sharp Edges Materials Used Must Be Food Grade. Must Be Branded 350.00 39,900.00 114 Pc Rubber Scraper. Type: Rubber Scraper Body Shape: Flat Material: Silicone Blade (head) & Plastic Handle (polypropylene) Color: Any Color Head Length: 11.5 Cm (minimum) Head Width: 7.0 Cm (minimum) Handle Length: 24 Cm To 30 Cm Preferably With Packing Case Safe Working Temperature: -40°f To 446°f The Materials Used Must Be Non-toxic. Must Be Branded 320.00 36,480.00 114 Pc Sauce Pan. Type: Sauce Pan Body Shape: Round In Shape Material: Stainless Steel With Aluminum Core Dimension: Diameter- 16 Cm X Height-8 Cm (minimum) Thickness: 1.8 Mm Thick (minimum) Riveted Stainless Steel Handle Length: 15 Cm (minimum) Capacity: 1 Quart (minimum) Preferably With Packing Case With Stainless Steel Cover, Safe For The Stove, Oven, Broiler And Dishwasher Safe The Materials Used Must Be Non-toxic. Must Be Branded 750.00 85,500.00 114 Pc Sheet Pan. Type: Sheet Pan Body Type: Rectangular Material: Aluminum Thickness: 0.91 Mm Thick (minimum) Dimension: Length-22 Inches X Width-16 Inches X Height-1 Inch (minimum) Preferably With Packing Case Smooth Finish Surfaces Without Sharp Edges Corrosion Resistant Superior Heat Conduction Oven Safe To 500°f / 260°c (maximum) Food Grade Must Be Branded. 350.00 39,900.00 475 Set Spoon, Measuring (set). Type: Measuring Spoon Body Shape: Bowl In Shape Material: Stainless Steel, 0.7 Mm Thick (minimum) The Set Consists Of The Following Sizes: 1 Pc - 1 Tbsp. (15 Ml) 1 Pc - 1/2 Tbsp. ( 7.5 Ml) 1 Pc - 1 Tsp. (5 Ml) 1 Pc - 1/2 Tsp. (2.5 Ml) 335.00 159,125.00 114 Pc Spoon, Wooden. Type: Wooden Spoon Body Shape: Oval Material: Hardwood Dimensions: Length- 10 Inches X Width- 2 Inches (minimum) Bowl Dimension: Length -3 Inches X Width 2 Inches X Depth -3/4 Inches (minimum) Total Length: 10 Inches (minimum) Preferably With A Packing Case Smooth Surface Finished And No Sharp Edges Handle With Provision For Hanging Storage Purposes Must Be Branded 265.00 30,210.00 114 Pc Strainer. Type: Strainer, Medium Fine Body Shape: Round Material: Stainless Steel Strainer Diameter: 20 Cm (minimum) Strainer Depth: 7 Cm (minimum) Handle Length: 18 Cm (minimum) With 2 Mm. (approx.) Fine Mesh Strainer’s Two Layers Of Tightly Woven Mesh Catches Handle Has Provision For Hanging Preferably With A Packing Case Dishwasher Safe. Must Be Branded. 450.00 51,300.00 380 Pc Tip, Decorating. Type: Tube Tips Body Shape: Nozzles With Different Shape Material: Stainless Steel Tube Height: 3.5 Cm To 5 Cm Tube Diameter: 2 Cm To 3.5 Cm Thickness: 0.5 Mm (minimum) Tube Tip: Assorted Designs (create Swirls, Rosettes, Flowers, Roping, Stars, Leaves And Other Designs Comes With 24 Different Shapes Of Nozzles Packed In Plastic Storage Box 895.00 340,100.00 114 Pc Weighing Scale, 10 Kgs. Must Be Branded. 1,632.00 186,048.00 114 Pc Weighing Scale, 5kgs Digital. Type: Mechanical Weighing Scale Body Type: Circular Bowl Material: Stainless Steel Bowl And Metal Body (coated) Mechanism Type: Spring Lever Capacity: 5 Kg /11 Lb. Sensitivity/graduated By 10 Gm Measurement Units: Gram/kilogram Manual Setting On Zero, Must Be Accurate And Durable Calibrate The Scale Using The Adjustment Knob Preferably With A Packing Case Delivery Must Include Instruction Manual Written In Good English With Service Centers Located In The Major Cities In The Philippines Warranty Period Of 1 Year (parts And Service). Must Be Branded 890.00 101,460.00 114 Pc Wire Whisk, Medium. Type Wire Whisk, Medium Body Shape: Ballon Material: Stainless Steel Wire Whisk Medium Dimensions (l X W): 25.4 Cm X 7 Cm (minimum) Handle Length: 10 Cm (minimum) With Hanging Loop No. Of Wires: 6 Wires Wire Diameter: 1.8 Mm (minimum) Preferably With A Packing Case Dishwasher Safe. Must Be Branded. 500.00 57,000.00 24 Pc Apple Corer. Body Shape: Tubular Material: Stainless Steel Total Length: 18 Cm (minimum) Handle Material: Hard Plastic, Polypropylene Handle Dimension: Length-10 Cm X Diameter-2 Cm (minimum) Blade Size: Length-8cm X Diameter-2 Cm (minimum) Preferably With Packing Case. Dishwasher Safe. 350.00 8,400.00 12 Pc Bain Marie, Table. (food Warmer) Body Shape: Rectangular Material: 304 Stainless Steel, 0.8 Mm Thick (minimum) Dimensions: Length-1500 Mm X Width-700mm X Height-800 Mm (minimum) Power Source: Voltage: 220 Volts - 230 Volts, 50 Hz/ 60 Hz With Royal Cord 1.5 Meter Long With Attachment Standard Type A Male Plug Or Provide Plug Adopter 10a/220v 16,000.00 192,000.00 8 Pc Blender, Electric. Body Shape: Round Jar Material Housing: Plastic (polypropylene) Jar Height: 25 Cm To 28 Cm Jar Thickness: 4 Mm To 8 Mm Heat Resistant Glass Jar With Cover Source Voltage: 220 Volts / 240 Volts,50 Hz / 60 Hz With Power Cord 1.5 Meter Long With Attachment Of Standard Type A Male Plug Or Provide Plug Adopter 10a/220v. Power Wattage: 300 To 700 Watts Blade: Stainless Steel, 3 To 4 Metal Blades 5,000.00 40,000.00 64 Pc Board, Chopping/cutting, Plastic. Type: Cutting Board Body Shape: Rectangular Material: Plastic (polypropylene), Food Grade Board Size: Length: 15 Inches (minimum) Width: 12 Inches (minimum) Thickness: 0.5 Inch (minimum) With Hole For Storage Purposes Preferably With Packing Case Food Grade And Dishwasher Safe 400.00 25,600.00 8 Pc Boiler, Double. Material: Stainless Steel Thickness: 1/16 Inch (1.5 Mm) (minimum) Lid Material: Glass Riveted Handle On Both Side Diameter: 9 1/2 Inches (minimum) Total Height: 9.4 Inches (minimum) Inset Bottom Diameter: 9 Inches (minimum) Inset Top Diameter: 9 Inches (minimum) Capacity: 2 Liters (minimum) 2,465.00 19,720.00 32 Pc Braising Pan, Medium. Body Shape: Round Material: Enameled Cast Iron And Stainless Steel Size: Diameter: 28 Cm X Height: 10 Cm (minimum) Capacity: 4 Liters (approximate) With Stainless Steel Cover, Solid Cast Stainless Steel Side Handles And Riveted Handle On Both Side: Length: 10 Cm (minimum) Handle Diameter: 8 Mm To 10 Mm 1,980.00 63,360.00 12 Pc Can Opener. Type: Can Opener Body Shape: Materials: Stainless Steel Dimension: Length-21 Cm X Width 10 Cm X Depth:2.5cm (minimum) Multi-use: 3 In 1 Can Opener Also Opens Bottle Tops- Can Lids And Tabs 300.00 3,600.00 24 Pc Casserole, Medium. Type: Casserole Pot Body Shape: Round Material: Stainless Steel, 0.7 Mm Thick Dimension: Diameter- 24 Cm X Height -14 Cm (minimum) Tempered Glass Lid Welded Handle On Both Sides, Size: 7.5 Cm (minimum) Handle Diameter: 8 Mm To 10 Mm Preferably With Packing Case 1,320.00 31,680.00 48 Pc Casserole, Small. Type: Casserole Pot Body Shape: Round Material: Stainless Steel, 0.7 Mm Thick Dimension: Diameter- 20 Cm X Height -12 Cm (minimum) Tempered Glass Lid Welded Handle On Both Sides, Size: 7.5 Cm (minimum) Handle Diameter: 8 Mm To 10 Mm 300.00 14,400.00 16 Pc Colander, Medium. Type: Colander, Medium Body Type: Round Material: 304 Stainless Steel Diameter: 30 Cm (minimum) Capacity: 8 Quarts (9 Liters) Welded Handle On Both Sides, Size: 7.5 Cm (minimum) Handle Diameter: 8 To 10 Mm 1,225.00 19,600.00 16 Pc Colander, Small. Type: Colander (small) Body Shape: Round Material: 304 Stainless Steel Diameter: 26 Cm (minimum) Capacity: 5 Quarts (5.6 Liters) Welded Handle On Both Sides, Size: 7.5 Cm (minimum) Handle Diameter: 8 Mm To 10 Mm Body Thickness: 0.8 Mm (minimum) Full-ring Support Base, 15 Cm Diameter Preferably With Packing Case. Food Grade And Dishwasher Safe 1,058.00 16,928.00 32 Set Cup, Measuring (for Solid) (set). Type: Measuring Cup Set Body Shape: Round Material: Stainless Steel, 0.7 Mm Thick (minimum) Each Set Contains The Following: 1 Pc - 1 Cup (237 Ml) 1 Pc - 1/2 Cup (118 Ml) 1 Pc - 1/3 Cup (79 Ml) 1 Pc - 1/4 Cup (59 Ml) Handle Dimension: Length-12 Cm X Width-1 Cm (minimum) Measuring Capacity Engraved On The Handle Strip Handles Have Provision For Hanging Preferably With Packing Case Smooth Surfaces And Dishwasher Safe 545.00 17,440.00 16 Pc Dispenser, Paper Towel. Body Shape: Rectangular Material: Abs Plastic Dimensions: Length =260 Mm X Width =100 Mm X Height = 211 Mm (minimum) Capacity: 200 Paper Paper Size: Length-20 Cm X Width- 8 Cm (approximate) Mounting Style: Wall Mounted Tissue Box 978.00 15,648.00 12 Pc Fan, Electric. Stand Fan, Electric Material: Metal, Plastic Size/diameter: 18 Inches Power Rating: 70 Watts (minimum), 220 / 240 Vac, 50 / 60 Hz, Single Phase, Rotation Angle: 90 Degrees Base: Stable, 16 Inches Diameter (approx.) Removable Metal Guard On Front And Rear 3-speed Settings, Comes With 1.5 Meters Power Cord And With Molded Male Plug To Adapt Type A Outlet (or Providing 3a Minimum Plug Adapter Is An Option) Smooth Surface, No Sharp Edges Includes User's Manual In English 2,655.00 31,860.00 8 Pc Fire Extinguisher (with Contents). 1.for Type A, B, C Fire: Dry Chemicals (monoammonium Phosphate) 2.portable Type 3.capacity : 5 - 6 Kgs 4.rechargeable Cylinder Metal 5.working Pressure Of Cylinder : 400 Psi 6.brass Valve With Pressure Gage 7.with Rubberized Hose And Aluminum Nozzle Attached 8.with Squeeze Lever To Discharge And Safety Pin 10.painted With Metal Primer And Red Enamel Paint 2,600.00 20,800.00 8 Pc Fish Poacher, Medium. Type: Fish Poacher Body Shape: Oval Pot For Poaching Material: Stainless Steel, 0.64 Mm Thick Dimensions (l X W X D): 45 Cm X 15 Cm X 12 Cm (minimum) Handle Material: Stainless Steel Riveted Looped Handles On Both Side, 7 Cm (minimum) Handle Diameter: 8 Mm To 10 Mm 2,500.00 20,000.00 16 Pc Fork, Carving. Body Shape: Square Shape Prong Prong Material: High Carbon Stainless Steel Overall Length: 30 Cm (minimum) Blade Dimension: Length- 15 Cm X Width- 0.5 Cm X Thickness- 0.3 Cm (minimum) Number Of Prongs: 2 Prong Comes With Square- Shaped Prongs And Pointed Tips Abs Plastic Triple-riveted Handle. Preferably With Packing Case 585.00 9,360.00 32 Pc Fork, Kitchen (pcs). Body Shape: Standard Material: Stainless Steel Dimension: Length - 32 Cm X Width- 3.5 Cm (minimum) Fork Size: Length: 8 Cm X Width -3.5 Cm (minimum) Handle: Abs Plastic Number Of Tines: 2 Tines With Tapered End 300.00 9,600.00 16 Pc Frying Pan, Large. Body Shape: Round Pan Material: Aluminum With Non-stick Coating Thickness: 3 Mm Thick (minimum) Dimension: Diameter-30 Cm (minimum) X Height- 5.5 Cm (minimum) Handle Material: Stainless Steel With Silicone Riveted Handle: 20 Cm Long (minimum) Preferably With A Packing Case, Oven Safe Up To 250⁰f 878.00 14,048.00 32 Pc Frying Pan, Medium. Body Shape: Round Pan Material: Aluminum With Non-stick Coating Thickness: 3 Mm Thick (minimum) Dimension: Diameter-24 Cm (minimum) X Height- 4.5 Cm (minimum) Handle Material: Stainless Steel With Silicone Riveted Handle: 19 Cm Long (minimum) Preferably With A Packing Case 735.00 23,520.00 48 Pc Frying Pan, Small. Body Shape: Round Pan Material: Aluminum With Non-stick Coating Thickness: 3 Mm Thick (minimum) Dimension: Diameter-20 Cm (minimum) X Height- 3.8 Cm (minimum) Handle Material: Stainless Steel With Silicone Riveted Handle: 12 Cm Long (minimum) Preferably With A Packing Case Oven Safe Up To 250⁰f 625.00 30,000.00 16 Pc Funnel, S/s, Medium. Type: Stainless Steel Funnel Body Shape: Round Material: 304 Stainless Steel Dimension: Diameter-15 Cm (minimum) X Height- 15.8 Cm (minimum) Tube Diameter: 2 Cm X Length: 7.3 Cm (minimum) Comes With Handle For Easy Hanging Preferably With Packing Case Dishwasher Safe 245.00 3,920.00 16 Pc Funnel, S/s, Small. Type: Stainless Steel Funnel Body Shape: Round Material: 304 Stainless Steel Dimension: Diameter-11 Cm (minimum) X Height- 10 Cm (minimum) Tube Diameter: 1.5 Cm X Length: 5 Cm (minimum) Comes With Handle For Easy Hanging Preferably With A Packing Case. Dishwasher Safe 185.00 2,960.00 16 Pc Garbage Bin. Type: Swivel Lid Garbage Bin Body Shape: Round Material: Hard Plastic, Polypropylene Dimension: Diameter-26 Cm X Height-47 Cm (minimum) Capacity: 4 Gallons (minimum) Removable Dome Shape Lid With Spring Return Swivel Preferably With A Packing Case Color: Any Color 685.00 10,960.00 48 Pc Glass Rack. Body Shape: Square Material: Polypropylene Plastic Overall Dimensions: Length - 19 1/2 Inches X Width - 19 1/2 Inches X Height - 4 Inches (minimum) Compartments: Full-size 25 Individual Compartment Glass Rack, Compartment Dimensions: Length - 3 1/2 Inches X Width - 3 1/2 Inches X Height - 4 Inches (minimum) Easy Grip Handles Molded Into All Four Sides Preferably With A Packing Case 2,980.00 143,040.00 8 Pc Ice Cream Scooper. Type: Ice Cream Scooper Body Shape: Round Material: Stainless Steel Scoop: Diameter- 5 Cm X Deep-2.5 Cm (minimum) Handle Length: 10 To 12 Cm 265.00 2,120.00 32 Pc Knife, Boning. Type: Flexible Boning Knife Body Shape: Ergonomic Material: High Carbon Steel Overall Length: 28 Cm (minimum) Blade: Length-15 Cm X Width- 3 Cm (minimum), Pointed Tip Cutting Edge Angle From Tip To The Heel Is 13 To 14 Degrees Handle Length: 12 Cm (minimum) Handle Material: Hard Plastic Handle With Rivets Preferably With Packing Case, Dishwasher Safe 462.00 14,784.00 40 Pc Knife, Chef. Type: Chef's Knife Body Shape: Flat Materials: Stainless Steel Overall Length: 30 Cm (minimum) Blade Size: Length - 20 Cm X Width-4 Cm (minimum) Blade Thickness: 2.5 Mm (minimum) 592.00 23,680.00 12 Pc Knife, Cleaver. Type: Cleaver Knife Body Shape: Flat Blade Material: Forged Stainless Steel Heavy Duty Blade Length: 17 Cm (minimum) Overall Length: 30 Cm (minimum Cutting Edge: Straight Handle Material: Ergonomic Wood Handle With Triple Rivets 1,495.00 17,940.00 16 Pc Knife, Oyster. Body Shape: Ergonomic Blade Material: Stainless Steel Blade Dimension: Length - 7 Cm (minimum) X Width - 2 Cm (minimum) Blade Thickness: 2 Mm (minimum) Handle Material: Smooth Wooded Handle Rounded Handle Size: Length-10 Cm X Diameter- 3.5 Cm (minimum) Total Length (from The Tip Of The Handle Up To Tip Of The Blade) :17 Cm (minimum) 335.00 5,360.00 8 Pc Light, Emergency. Emergency Light, 2 Heads Led Materials: Metal, Anti-rust Coated Duration Time (2 Heads): 5 Hours (minimum) Automatically Light Up During Power Outage Overcharge And Over- Discharge Protection Built - In Ac Charger, Power Cord Plug To Adapt Type A Outlet (or Providing 5a Minimum Plug Adapter Is An Option) Battery Test Switch - External Safety Fuse Head: White Led 1w (minimum) 3.5 " Dome Reflector 2,850.00 22,800.00 8 Pc Meat Slicer, Small. Body Shape: Circular Housing Material: Die Cast Aluminum Alloy And Body Painted Dimensions: Width-40.5 Cm X Depth- 45.7 Cm X Height- 38 Cm (minimum) Stainless Steel Rotary Blade Diameter: 190 Mm (minimum) Power Source: 220 Volts-230 Volts, 60 Hz With Power Cord 1.5 Meter Long With Attachment Of Standard Type A Male Plug Or Provide Plug, Adopter 10a/220v 15,242.00 121,936.00 32 Pc Pastry Tube. Body Shape: Tube In Different Shape Of Nozzles Material: Stainless Steel Set Contain: 24 Different Shapes Of Nozzles (minimum) Tube Height: 3.5 Cm To 5 Cm Tube Diameter: 2 Cm To 3.5 Cm Thickness: 0.5 Mm (minimum) Tube Tip: Assorted Designs (create Swirls, Rosettes, Flowers, Stars, Leaves And Other Designs 168.00 5,376.00 32 Pc Peeler, Y-type. Body Shape: Ergonomic, Material: Stainless Steel Overall Dimensions (l X W X H): 7 Inches X 2 1/4 Inches X 1 Inch (minimum) Blade Material: 304 Stainless Steel, 0.7 Mm Head Dimension: (l X W X H) 2 1/4 Inches X 2 1/4 Inches X 1 Inch (minimum) Handle Material: Stainless Steel Handle Length: 4 3/4 Inches X 1 Inch Diameter (minimum) 295.00 9,440.00 32 Pc Pepper And Salt Mill. Body Shape: Round Body Material: Wood Size: Diameter: 5 Cm X Height: 20 Cm (minimum) Carved Of Wood With Stainless Steel Grinding Mechanism, Color: Natural Screw Cap At The Top Of The Mill To Adjust The Thickness Of Peeper Or Spices Preferably With A Packing Case 500.00 16,000.00 32 Pc Piping Bag (packs). Body Shape: Triangular Material: Transparent Disposable Plastic For Dispensing Ingredients To Pastries Length: 9 Inches Minimum Width: 3 Inches (minimum) Volume: 500 Ml (approximate) 265.00 8,480.00 48 Pc Plate Rack. Type: Plate Rack Body Shape: Rectangular Material: 304 Stainless Steel Dimension: Length-475 Mm X Width- 290 Mm X Height- 380 Mm (minimum) 4,890.00 234,720.00 24 Pc Preparation Table With Sink. Type: Preparation Table With Sink & Shelves Body Shape: Rectangular Material: Stainless Steel, 1 Mm Thick (minimum) Dimensions: L-1200 Mm X W - 700 Mm X H - 850 Mm (minimum) Stainless Steel Table Top And Stainless Steel Under Shelf Fully Welded Construction Sink: Left Side Single Bowl Sink With Drainer 4 Inches & Faucet Provision Sink Dimension (l X W X D) 400 Mm X 500 Mmx 25 Mm (minimum) 20,000.00 480,000.00 8 Pc Pressure Cooker. Type: Pressure Cooker Body Shape: Round Material: Polished Aluminum Dimension: Diameter: 32 Cm X Height: 25 Cm (minimum) Capacity: 10 Quarts (11.3 Liters) Side Handles For Secure Carrying Equipped With Safety Opening Mechanism, Spring Safety Valve, Rubber Seal Ring 4,760.00 38,080.00 16 Pc Roasting Pan. Type: Roasting Pan Body Shape: Rectangular Material: Stainless Steel Dimension: Length: 40 Cm X Width-35 Cm X Height -7 1/2cm (minimum) Thickness: 1.5 Mm Thick (minimum) Welded Handles On Both Sides Removable Stainless Steel Wire Rack 1,400.00 22,400.00 32 Pc Scissors, Kitchen. Type: Kitchen Scissor Body Shape: Ergonomic Blade Material: Stainless Steel, 2 Mm Thick Handle Material Heavy Duty Acrylonitrile Butadiene Styrene (abs) Plastic Overall Length: 20 Cm (minimum ) Width: 7.5 Cm (minimum) 250.00 8,000.00 32 Pc Siever, Small. Type: Fine Mesh Siever Body Shape: Round Material: Stainless Steel Diameter: 20 Cm (minimum) Depth: 7 Cm (minimum) Twin Wire Handle: Length 20 Cm X 5 Mm Diameter (minimum) Fine Mesh: 0.7 Mm (1/32 Inch) (minimum) Preferably With A Packing Case 475.00 15,200.00 32 Pc Skimmer, Fine. Type: Medium Fine Mesh Skimmer Body Shape: Round Material: Stainless Steel, Polished Overall Length: 34 Cm (minimum) Skimmer Head: Diameter -10 Cm X Depth- 4 Cm (minimum) Diameter Of Holes: 2 Mm (approx.) Handle: Length- 12 Cm X Diameter- 2 Cm (minimum) Handle Has Hole For Hanging Preferably With A Packing Case 140.00 4,480.00 32 Pc Skimmer, Spider. Body Shape: Round Material: Stainless Steel, Polished Overall Length: 35 Cm (minimum) Skimmer Head Diameter: 15 Cm X Depth 4 Cm (minimum) Handle Length: 12 Cm X 2 Cm Diameter (minimum) Preferably With A Packing Case Dishwasher Safe 435.00 13,920.00 48 Pc Soup Cup Rack. Type: Soup Cup Rack Body Shape: Square Material: Polypropylene Plastic Dimension: Length: 50 Cm X Width: 50 Cm X Height: 10 Cm (minimum) Compartment Length: 11 Cm Compartment Width: 11 Cm Compartment /inside Height: 6.7 Cm No. Of Compartment: 16 Compartments 2,000.00 96,000.00 32 Pc Soup Ladle, 3oz. Body Shape: Round Material: Stainless Steel Thickness: 1 Mm Thick (minimum) Handle Length: 28 Cm (minimum) Capacity: 3 Oz. (85 Ml) Ladle Type: Round Bottom Hooked Handle Design Allows It To Easily Sit On The Edge Of Pots. Preferably With A Packing Case, Dishwasher Safe 250.00 8,000.00 32 Pc Soup Ladle, 6oz. Body Shape: Round Material: Stainless Steel Thickness: 1 Mm Thick (minimum) Handle Length: 30 Cm (minimum) Capacity: 6 Oz. (170 Ml) Ladle Type: Round Bottom Hooked Handle Design Allows It To Easily Sit On The Edge Of Pots. Preferably With A Packing Case. Dishwasher Safe. 290.00 9,280.00 16 Pc Soup Ladle, 8oz. Body Shape: Round Material: Stainless Steel Thickness: 1 Mm Thick (minimum) Handle Length: 30 Cm (minimum) Capacity: 8 Oz. (236 Ml) Ladle Type: Round Bottom Hooked Handle Design Allows It To Easily Sit On The Edge Of Pots. Preferably With A Packing Case 350.00 5,600.00 16 Pc Soup Ladle, 12oz. Body Shape: Round Material: Stainless Steel Thickness: 1 Mm Thick (minimum) Handle Length: 34 Cm (minimum) Capacity: 12 Oz. (341 Ml) Ladle Type: Round Bottom Hooked Handle Design Allows It To Easily Sit On The Edge Of Pots. Preferably With A Packing Case. Dishwasher Safe. 400.00 6,400.00 32 Pc Spatula. Type: Offset Spatula Body Shape: Flat Blade Material: Stainless Steel 316 Handle Material: Hardwood (smooth Finish) With Rivets Blade Dimension: Length= 7 .5 Inches X Width-1.5 Inches (minimum) Thickness Of Blade: 1.7 Mm Thick (minimum) Total Length = 12 To 14 Inches Preferably With A Packing Case Dishwasher Safe. Must Be Branded. 365.00 11,680.00 32 Pc Spoon, Kitchen. Type: Kitchen Spoon Body Shape: Oval Material: Stainless Steel, 1.5 Mm Thick Overall Length: 30.5 Cm X Width-7.5 Cm (minimum) Spoon Head Dimension (l X W) 9 Cm X 7.5 Cm (minimum) Handle: Abs Plastic Spoon Head: Oval Type Preferably With A Packing Case Heat Resistant Up To 220 ° C Dishwasher Safe. Must Be Branded. 300.00 9,600.00 32 Pc Spoon, Kitchen (slotted). Type: Kitchen Spoon Slotted. Body Shape: Oval With Slot Material: Stainless Steel, 1.5 Mm Thick Overall Length: 30.5 Cm X Width-7.5 Cm (minimum) Spoon Head Dimension (l X W) 9 Cm X 7.5 Cm (minimum) Handle: Abs Plastic Spoon Head: Oval Type With Slot At Least 6 Rectangular Slots. Preferably With A Packing Case Heat Resistant Up To 220 ° C. Dishwasher Safe 425.00 13,600.00 32 Set Spoon, Measuring (set). Type: Measuring Spoon Body Shape: Bowl In Shape Material: Stainless Steel, 0.7 Mm Thick (minimum) The Set Consists Of The Following Sizes: 1 Pc - 1 Tbsp. (15 Ml) 1 Pc - 1/2 Tbsp. ( 7.5 Ml) 1 Pc - 1 Tsp. (5 Ml) 1 Pc - 1/2 Tsp. (2.5 Ml) 335.00 10,720.00 32 Pc Spoon, Parisienne. Type: Parisiennes Spoon Body Shape: Round Double Headed Parisiennes Scoop Bar Tool Material: Stainless Steel, Polished Overall Length: 240 Mm (minimum) Scoop Diameter: 30 Mm And 24mm (minimum) With Plastic Handle (polypropylene), Size: 130 Mm X Width-20 Mm (minimum) Draining Small Hole In The Scoop 345.00 11,040.00 96 Pc Spoon, Serving. Body Shape: Oval Materials: Stainless Steel Dimension: Length: 23 Cm X Width: 5 Cm (minimum) Scoop Dimension (l X W X D): 7 Cm X 5 Cm X 0.9 Cm (minimum) Spoon Thickness: 1.6 Mm (minimum) Preferably With A Packing Case Dishwasher Safe. Must Be Branded. 200.00 19,200.00 32 Pc Spoon, Wooden. Body Shape: Oval Material: Hardwood Dimensions: Length- 10 Inches X Width- 2 Inches (minimum) Bowl Dimension: Length -3 Inches X Width 2 Inches X Depth -3/4 Inches (minimum) Total Length: 10 Inches (minimum) Preferably With A Packing Case Smooth Surface Finished And No Sharp Edges 300.00 9,600.00 16 Pc Stock Pot, Large. Type: Stock Pot, Large Body Shape: Round Material: Stainless Steel, 0.8 Mm Thick (minimum) Top Diameter: 30 Cm (minimum) Height: 31 Cm (minimum) Capacity: 20 Quarts (22.7 Liters) Oven Safe To 350⁰f And Dishwasher Safe. With Aluminum Disc Layer In Bottom For Even Heat (5 Mm Aluminum 3,590.00 57,440.00 16 Pc Strainer, Chinois, Medium. Type: Strainer Chinois, Medium Body Shape: Conical Material: Stainless Steel Strainer Diameter: 20 Cm (minimum) Strainer Depth: 21.5 Cm (minimum) Handle Length: 20 Cm (minimum) With 2 Mm. (approx.) Fine Mesh Handle Has Provision For Hanging Preferably With A Packing Case Dishwasher Safe Must Be Branded 735.00 11,760.00 16 Pc Strainer, Chinois, Small. Strainer Chinois, Small Body Shape: Conical Material: Stainless Steel Strainer Diameter: 14 Cm (minimum) Strainer Depth: 13 Cm (minimum) Handle Length: 15 Cm (minimum) With 1 Mm (approx.) Fine Mesh Handle Has Provision For Hanging Preferably With A Packing Case Dishwasher Safe Must Be Branded 675.00 10,800.00 32 Pc Strainer Medium, Fine. Type: Strainer, Medium Fine Body Shape: Round Material: Stainless Steel Strainer Diameter: 20 Cm (minimum) Strainer Depth: 7 Cm (minimum) Handle Length: 18 Cm (minimum) With 2 Mm. (approx.) Fine Mesh Strainer’s Two Layers Of Tightly Woven Mesh Catches Handle Has Provision For Hanging Preferably With A Packing Case Dishwasher Safe Must Be Branded. 465.00 14,880.00 32 Pc Strainer Small, Fine. Type: Strainer, Small Fine Body Shape: Round Material: Stainless Steel Strainer Diameter: 13 Cm (minimum) Strainer Depth: 5 Cm (minimum) Handle Length: 13 Cm (minimum) With 1 Mm. (approx.) Fine Mesh Handle Has Provision For Hanging Preferably With A Packing Case Dishwasher Safe. Must Be Branded 325.00 10,400.00 20 Pc Table, Working. Type: Working Table, Stainless Steel. Body Shape: Rectangular Material: 304 Stainless Steel, 1.29 Mm Thick (gauge 16) Minimum Length: 1220 Mm (minimum) Width: 700 Mm (minimum) Height: 850 Mm (minimum) Tubular Stainless Steel Legs, 38mm (minimum) With 4 Adjustable Bullet Feet Fully Welded Construction Thickness: Gauge 16 (1.29 Mm Thick) Minimum Stainless Steel Table Top With Stainless Steel Undershelf Distance Between Table Top And Undershelf Is 650 Mm (minimum) Preferably With A Packing Case Or Crate No Sharp Edges And Rough Surfaces. Must Be Branded. 19,500.00 390,000.00 32 Pc Tenderizer, Medium. Type: Tenderizer Body Shape: Ergonomic Material: Cast Aluminum Overall Length: 26 Cm (minimum) Dual-sided Hammer, Square Head: 6 Cm X 6 Cm (minimum) Ridged Surface With Rows Of Dull, Pyramid-shaped Spikes, Weight: 250 Grams To 500 Grams Preferably With A Packing Case Dishwasher Safe. Must Be Branded 315.00 10,080.00 16 Pc Thermometer, Pocket/pin. Type: Pocket/pen Thermometer Body Shape: Tubular Pen Style Digital Thermometer Product Size: 100 Mm X 40 Mm X 14 Mm (minimum) Display Size: 40 Mm X 20 Mm (minimum) Prove Length: 200 Mm (minimum) Measuring Range: -50 °c To 300 °c (-58 ⁰f To 372 ⁰f) Resolution: 0.1 °c / 0.2 °f 600.00 9,600.00 32 Pc Tong, 12 Inches. Body Shape: Standard Material: Stainless Steel Size: 12 Inches Stainless-steel Arms With Soft, Comfortable Grips Nylon Heads Safe For Nonstick Cookware Heat-resistant Up To 400 Degrees Fahrenheit Tongs Lock Closed For Storage Preferably With A Packing Case Food Grade And Dishwasher-safe. Must Be Branded 320.00 10,240.00 40 Pc Tong, 8 Inches. Body Shape: Standard Material: Stainless Steel,size: 8 Inches Stainless-steel Arms With Soft, Comfortable Grips Nylon Heads Safe For Nonstick Cookware Heat-resistant Up To 400 Degrees Fahrenheit Tongs Lock Closed For Storage Preferably With A Packing Case. Food Grade And Dishwasher-safe 250.00 10,000.00 32 Pc Tray, Baking, Small. Type: Baking Tray Body Shape: Rectangular Material: Stainless Steel Dimension: 20 Cm X 30 Cm X 3.7 Cm (minimum) Body Thickness: 0.7- 1.0 Mm Preferably With Packing Case Dishwasher Safe. Must Be Branded 556.00 17,792.00 48 Pc Tray, Utility. Type: Utility Tray Body Shape: Rectangular Material: Stainless Steel Dimension: Length- 48 Cm X Width-32 Cm X Height-2.5 Cm (minimum) Reinforced Edges Finish: Polished. Preferably With A Packing Case. Washable And Oven Safe 485.00 23,280.00 32 Pc Turner 3" X 6. Body Shape: Straight Material: Stainless Steel Blade Size (lx W): 6 Inches X 3 Inches (minimum) Handle Length: 5 Inches (minimum) Overall Length: 13 Inches (minimum) Solid Turner With Straight Slotted Blade Wooden Handle With Triple Rivets Preferably With A Packing Case Dishwasher Safe. Must Be Branded 398.00 12,736.00 8 Pc Utility Cart. Body Shape: Rectangular Material: Plastic, Polypropylene(pp) Dimension: (l X W X H) 84 Cm X 43 Cm X 95 Cm (minimum) Capacity: 330 Lbs (150 Kg) Loads (minimum) Three (3) Shelving With At Least 25 Cm Distance Between Shelves Tub Shelf Measure (l X W X D) 84 Cm X 43 Cm X 7 Cm (minimum) With Four (4) Swivel Caster, 10 Cm Diameter, Two Which Have Locking Brakes Preferably With A Packing Case Easy Grip Handles On Each End Of Cart 5,000.00 40,000.00 16 Pc Weighing Scale, 1 Kg Digital. Type: Digital Weighing Scale, Body Shape: Rectangular Materials: Engineering Plastic And Stainless Steel Weighing Plate, Capacity: 1 Kg, Accuracy: 1 Gram Back Light Lcd Display With 15 Mm Minimum High Digits, Weighing Units: Gram, Ounce, Pound Size: (l X W X H Mm ) 163 Mm X 245 Mm X 79 Mmm (minimum) 720.00 11,520.00 8 Pc Weighing Scale, 5 Kilograms, Mechanical. Type: Mechanical Weighing Scale Body Type: Circular Bowl Material: Stainless Steel Bowl And Metal Body (coated) Mechanism Type: Spring Lever Capacity: 5 Kg /11 Lb. Sensitivity/graduated By 10 Gm Measurement Units: Gram/kilogram Manual Setting On Zero, Must Be Accurate And Durable Calibrate The Scale Using The Adjustment Knob Preferably With A Packing Case Delivery Must Include Instruction Manual Written In Good English With Service Centers Located In The Major Cities In The Philippines Warranty Period Of 1 Year (parts And Service) Must Be Branded 1,540.00 12,320.00 32 Pc Wire Skimmer, Small. Type: Skimmer, Wire Mesh Body Shape: Round Material: Stainless Steel, Polished Overall Length: 40 Cm (minimum) Skimmer Head Diameter: 12 Cm (minimum) Diameter Of Holes: 2 Mm (approx.) Handle Has Hole For Hanging. Preferably With A Packing Case. Dishwashing Safe. Must Be Branded. 295.00 9,440.00 16 Pc Wire Whisk, Heavy Duty. Type: Wire Whisk, Heavy Duty. Body Shape: Ballon Material: Heavy Duty Stainless Steel Dimensions (l X W): 31.8 Cm X 7.6 Cm (minimum) Handle Length: 12 Cm (minimum) With Hanging Loop No. Of Wires: 8 Wires Wire Diameter: 2 Mm (minimum) Preferably With A Packing Case Dishwasher Safe. Must Be Branded. 335.00 5,360.00 32 Pc Wire Whisk, Medium. Type Wire Whisk, Medium Body Shape: Ballon Material: Stainless Steel Wire Whisk Medium Dimensions (l X W): 25.4 Cm X 7 Cm (minimum) Handle Length: 10 Cm (minimum) With Hanging Loop No. Of Wires: 6 Wires Wire Diameter: 1.8 Mm (minimum) Preferably With A Packing Case Dishwasher Safe. Must Be Branded 425.00 13,600.00 32 Pc Wire Whisk, Small. Type: Wire Whisk, Small Body Shape: Balloon Material: Stainless Steel Wire Whisk Medium Dimensions (l X W): 20.3 Cm X 6 Cm (minimum) Handle Length: 10 Cm (minimum) With Hanging Loop No. Of Wires: 6 Wires Wire Diameter: 1.8 Mm (minimum) Preferably With A Packing Case Dishwasher Safe. Must Be Branded. 385.00 12,320.00 8 Pc Wok, Medium. Body Shape: Round Material: Carbon Steel Thickness: 1.8 Mm Thick (minimum) Dimensions (dia. X H): 45 Cm X 14 Cm (minimum) Handle Material: Steel Riveted Convenient Both Side Handle 10 Cm (minimum) With Flat Bottom. Preferably With A Packing Case Dishwashing Safe. Must Be Branded 1,950.00 15,600.00 16 Pc Wok, Small Body Shape: Round Material: Carbon Steel Thickness: 1.5 Mm Thick (minimum) Dimensions (dia. X H): 36 Cm X 10 Cm (minimum) Handle Material: Steel Riveted Convenient Both Side Handle 8 Cm (minimum) With Flat Bottom. Preferably With A Packing Case Dishwashing Safe. Must Be Branded 1,650.00 26,400.00 32 Pc Zester. Body Shape: Standard Material: Stainless Steel Grating Surface Dimensions (l X W): 20.3 Cm X 4 Cm (minimum) Overall Length: 32.5 Cm (minimum) Handle Material: Plastic (polypropylene) Ergonomic Handle. Preferably With A Packing Case Dishwasher Safe. The Plastic Material Used Must Be Non-toxic. Must Be Branded. 390.00 12,480.00 768 Pc Chair, Dining. Type : Dining Side Chair Body Shape: Square Material : Metal (round Or Square) Dimension: Total Height - 33" X 15" X15" (minimum) Capacity: 150 Kg. Black Colored Powder Coated Frame With Foam On Seat Packed In Carton Box The Item Must Have Good Quality. 2,200.10 1,689,676.80 32 Pc Coffee Pot, 2 Pints. Type: Manual Drip Body Shape: Round Material : Stainless Steel With Cover Capacity : 2 Pints Outside Diameter : 90 -110 Mm Over-all Height : 200 - 230 Mm Thickness : 0.5 - 1 Mm With Handle And Spout Packed In Carton Box. The Item Must Have Good Quality 1,156.00 36,992.00 80 Pc Container, Creamer. Design: Type: Porcelain With Spout Body Shape: Circular Material: Porcelain Diameter: 50 - 65 Mm Height : 80 – 105 Mm Color: White Appearance : Glossy White Packed In Carton Box. The Item Must Have Good Quality 328.00 26,240.00 384 Pc Cups And Saucers 5-6 Oz. 1. Material: Porcelain 2. Capacity: 5 Oz./140 Ml 3. Heatproof Up To 300 Deg. C 4. Color: White 5. The Item Must Be Of Good Quality 6. Packed In Carton Box 285.00 109,440.00 384 Pc Fork, Cocktail. 1. Material/appearance: Stainless Steel, Highly Polished, W/ Plain Design 2. Type : Rounded Tip Handle 3. Over-all Length : 110 - 165 Mm 4. Width : 20 - 30 Mm (minimum) 5. Handle Thickness : 2 Mm To 4 Mm 6. Handle Length : 75 - 90 Mm 7. Small, 8. Color : Silver 9. The Item Must Be Branded And Have Good Quality. 195.00 74,880.00 384 Pc Fork, Dessert. Type : Dessert Fork Body Shape: Fork Shape, Round Tip Material/appearance : Stainless Steel, Highly Polished, With Plain Design, Rounded Tip Handle Length : 150 Mm - 175 Mm Width : 20 - 30 Mm Handle Thickness : 1.5 Mm - 3 Mm Number Of Tines : 4 Handle : 130 Mm (minimum) Color : Silver Packed In Plastic Pouch The Item Must Be Of Good Quality 195.00 74,880.00 384 Pc Fork, Dinner. Type: Dinner Fork Body Shape: Fork Shape Material / Appearance : Stainless Steel, Highly Polished, With 4 Tines Over - All Length : 120 - 175 Mm Thickness Of Handle : 2 - 3 Mm Color : Silver, Packed In Plastic Pouch The Item Must Be Of Good Quality 185.00 71,040.00 384 Pc Fork, Fish. Type : Fish Fork Body Shape: Fork Shape With Round Tip Material / Appearance : Stainless Steel, Highly Polished, With Plain Design Over-all Length : 180 - 215 Mm Fork Width : 1.5 Mm - 3 Mm Fork Thickness : 1 Mm - 2 Mm Number Of Tines : 4 Length Handle : 120 - 130 Mm Handle Thickness : 2 Mm - 3 Mm Color : Silver. Packed In Plastic Pouch. The Item Must Be Of Good Quality 195.00 74,880.00 384 Pc Fork, Oyster. Type: Oyster Fork Body Shape: Fork Shape Material: Stainless Steel, With High Polish Appearance, And With Plain Design Length: 90 - 120 Mm Thickness: 1 Mm - 3 Mm Silver Color With Three Short Wide Curved Tines Packed In Plastic Pouch The Item Must Be Of Good Quality 225.00 86,400.00 384 Pc Glass, Champagne Flute. Type : Flute Glass Body Shape: Round Material: Clear Crystal Glass Dimension : Height: 20 -24 Cm, Top Diameter: 50 -70 Mm, Bottom Diameter: 60 - 80 Mm Capacity: 250 Ml. (minimum) Thickness: 1.5 - 3 Mm Packed In Carton Box The Item Must Have Good Quality 170.00 65,280.00 384 Pc Glass, Collins. Type: Tumbler Body Shape: Round Material : Clear Glass Capacity : 10 Oz To 14 Oz Thickness : 1.5 -3 Mm (minimum) Packed In Carton Box The Item Must Have Good Quality 102.00 39,168.00 384 Pc Glass, Juice/ Hi-ball. 1. Material : Clear Glass 2. Type : Hi-ball 3. Height : 140 - 160 Mm 4. Bottom Diameter : 50 -70 Mm 5. Top Diameter : 50 - 70 Mm 6. Thickness : 2 - 4 (minimum) 7. Capacity : 8 Oz. To 10 Oz. 8. Dishwasher Safe 9. The Item Must Be Branded And Good Quality 10. Packed In Carton Box 115.00 44,160.00 384 Pc Glass, Pilsner (ice Tea Glass). Type: Flaired Rim Body Shape: Round Slender Material: Clear Glass Capacity: 20 Oz. To 23 Oz. Over-all Length: 22 -25 Cm Thickness Of Glass : 1 -3 Mm With Flared Rim And Slender Shape Packed In Carton Box The Item Must Have Good Quality 120.00 46,080.00 384 Pc Glass, Red Wine. Type: Royalty Body Shape: Balloon Shaped Bowl Material: Crystal Clear Glass Rim Diameter : 55 - 60 Mm Thickness : 1.5 Mm - 3 Mm Over - All Length : 200 -220 Mm Capacity : 250 -300 Ml Stem Diameter : 6 - 8 Mm Stem Length : 85 - 90 Mm Base Diameter : 75 - 85 Mm Base Thickness : 2 - 4 Mm 300.00 115,200.00 384 Pc Glass, White Whine. Type: Royalty Body Shape: Balloon Shaped Bowl Material: Crystal Clear Glass Rim Diameter : 55 - 60 Mm Thickness : 1.5 - 3 Mm Over -all Length : 200 -220 Mm Capacity : 270 - 300 Ml Stem Diameter : 6 - 8 Mm Stem Length : 75 - 85 Mm Base Diameter : 70 - 80 Mm Base Thickness : 2 - 5 Mm 300.00 115,200.00 96 Pc Gravy Boats. Type: Steel Type Body Shape: Boat Shape With Handle Material: Stainless Steel Capacity : 5 Oz. Appearance: Mirror Polish Finish Size :17cm X 7.3cm X 8.2 Cm / 6.7 X 2.9 X 3.2 Inches (minimum) The Item Must Have Good Quality Packed In Plastic Pouch 560.00 53,760.00 64 Pc Ice Bucket, 2 Liters With Tongs. Type: Steel Type, Body Shape: Circular Set Includes: A. Ice Bucket Material : Stainless Steel Diameter : 140 - 180 Mm Height : 140 - 170 Mm Thickness Of Bucket : 0.7 - 2 Mm Capacity : 2 Liters (minimum) The Item Must Have Good Quality 496.00 31,744.00 384 Pc Knife, Butter. 1. Material : Stainless Steel W/ Highly Polished Appearance 2. Over-all Length : 140 Mm - 150 Mm 3. Handle Thickness : 3 Mm - 5 Mm 4. With Dull Edge And Rounded Tip 5. The Item Must Have Good Quality. 6. Packed In Carton Box 180.00 69,120.00 384 Pc Knife, Dinner. Type: Dinner Knife Body Shape: Flat With Round Tip Material / Appearance : Stainless Steel Blade Highly Polished Handle Material : Stainless Steel Overall Length : 160 - 190 Mm Blade Thickness : 2 - 4 Mm Handle Thickness : 3 - 6 Mm Serrated Blade With Rounded Tip Packed In Carton Box The Item Must Have Good Quality 180.00 69,120.00 384 Pc Knife, Fish. Type : Fish Knife Body Shape: Flat With Pointed Tip Material / Appearance : Stainless Steel, Highly Polished W/ Plain Design Overall Length : 200 - 220 Mm Width Blade : 20 - 25 Mm Thickness Of Blade : 2 Mm - 4 Mm Thickness Of Handle: 3 Mm - 6 Mm Wide Blade, Dull Edge, Tip Made With A Notched Point Color : Silver, Packed In Carton Box The Item Must Have Good Quality 180.00 69,120.00 64 Pc Folder, Menu. Type: Leather Menu Folder Body Shape: Rectangular Material: Leather With 2 Partitions And 6 Inserts Size: 31.5cm X 24.5cm Color: Brown/black Applicable Paper Size: A4 234.00 14,976.00 96 Pc Napkin Holder. Type: Steel Type Body Shape: Rectangular Material : Stainless Steel With Highly Polished Appearance Dimension : Width : 70 - 90 Mm X Length : 150 - 170 Mm , Thickness : 0.7 Mm -2 Mm Packed In Plastic Pouch The Item Must Have Good Quality 350.00 33,600.00 64 Pc Order Pads. Type: Numbered Pads Body Shape: Rectangular Material : 80 Gsm Offset Paper Each Pad Comes With A 100 Sheets And Corresponding Copy Page Each Pad Has Sequentially Numbered Orders To Make It Easy To Keep Track With 100 Sheets Per Pad And 10 Pads Included Can Take 1000 Orders Before You Run Out Packed In A Plastic Pouch 85.00 5,440.00 64 Pc Pepper And Salt Mill. Type: Pepper & Salt Mill Body Shape: Round Body Material: Wood Size: Diameter: 5 Cm X Height: 20 Cm (minimum) Carved Of Wood With Stainless Steel Grinding Mechanism Color: Natural Screw Cap At The Top Of The Mill To Adjust The Thickness Of Peeper Or Spices Preferably With A Packing Case Food Grade And Nontoxic. Must Be Branded 500.00 32,000.00 128 Pc Plate Covers. Type: Steel Type Body Shape: Circular Material: Stainless Steel, Mirror Polished Diameter: 10 1/4 Inches (minimum) Height: 2 7/8 Inches (minimum) Thickness: 1/16 Inch. (minimum) With Handle, Packed In Plastic Pouch The Item Must Have Good Quality 600.00 76,800.00 384 Pc Plate, Dessert, 7" To 8" . Type: Plain Type Body Shape: Circular Material: Porcelain Supply Must Be A Set, Consisting Of One (1) Of Each: 7 Inches And 8 Inches Plates Color : White Inner Diameter: 145 To 165 Mm Thickness : 3 To 6 Mm Smooth And Glossy Surfaces Packed In Carton Box, The Item Must Have Good Quality 225.00 86,400.00 384 Pc Plate, Dinner, 10". Type: Plain Type Body Shape: Circular Material: Porcelain With No Design Color: White Inner Diameter : 200 Mm - 215 Mm Outer Diameter : 250 - 260 Mm Thickness : 3 Mm - 6 Mm Smooth And Glossy Surfaces Packed In Carton Box The Item Must Have Good Quality 265.00 101,760.00 384 Pc Plate, Fish, 8" To 9" . Type: Plain Type, Body Shape: Circular, Material : Porcelain With No Design Supply Shall Be A Set Consisting Of: One (1) Each 8 Inches And One (1) Each, 9 Inches Color : White, Inner Diameter : 165 Mm - 190 Mm (minimum) Thickness : 3 Mm - 6 Mm Smooth And Glossy Surfaces Packed In Carton Box The Item Must Have Good Quality 225.00 86,400.00 128 Pc Table, Round (8's). Type: Foldable Body Shape: Round Material: High Density Polyethylene Table Top Powder Coated Steel Frame Size: 154cm X 74cm X4.5cm (minimum) Good For 8 To 10 Seater Capacity Tube Size : 28 Mm Diameter X 1 Mm Thickness Packed In A Carton Box. The Item Must Have Good Quality 6,500.00 832,000.00 384 Pc Fork, Salad. Type: Salad Fork Body Shape: Fork Shape Material/appearance: Stainless Steel, Highly Polished, With 4tines, Length: 150 Mm - 175 Mm Thickness Of Handle : 2 Mm - 3 Mm Color: Silver Packed In Plastic Pouch Item Must Be Of Good Quality. 125.00 48,000.00 384 Pc Knife, Salad. Type: Salad Knife Body Shape: Semi Rectangular Blade With Pointed Tip Material/appearance: Stainless Steel, Highly Polished, W/ Plain Design Overall Length: 145 -160 Mm Blade Thickness: 2 Mm To 4 Mm Handle Thickness: 4 Mm To 6 Mm Handle Material: Stainless Steel Rounded Tip Handle Packed In Carton Box The Item Must Have Good Quality 125.00 48,000.00 384 Pc Salad Plates 7" To 8" . Type: Plain Type Body Shape: Circular Material: Porcelain With No Design Supply Must Be A Set Consisting Of One (1) Each: 7 Inches And 8 Inches Plates Color: White Diameter (inner): 150 Mm - 165 Mm Thickness: 3 Mm - 6 Mm Smooth And Glossy Surfaces Packed In Carton Box. The Item Must Have Good Quality 215.00 82,560.00 64 Pc Salt And Pepper Shakers. Type: Glass Type Body Shape: Square Material: Glass And Aluminum Over-all Height: 75 -90 Mm Length: 50 -60 Mm, Width: 50 -60 Mm Aluminum Cover. Packed In Carton Box The Item Must Have Good Quality 550.00 35,200.00 64 Pc Sauce Ladles. Type: Spouted Bowl Body Shape: Circular With Pouring Spout Material: Stainless Steel, Highly Polished Appearance Over-all Length: 220 -230 Mm Ladle Bowl Length: 60 -65 Mm Long Ladle Bowl Diameter: 65 -70 Mm Depth: 10 -15 Mm Handle Details: 150-155 Mm Long X 20 -30 Mm Wide X 2 - 4 Mm Thick, Color: Silver With Hang Hole For Hanging And Easy Access Dishwasher Safe. Packed In Plastic Pouch The Item Must Have Good Quality 395.00 25,280.00 64 Pc Server, Cake. 1. Material : Stainless Steel Blade , Highly Polished Appearance 2. Over-all Length : 220 To 270 Mm 3. Width : 60 - 80 Mm 4. Thickness : 1.5 Mm To 2 Mm 5. Handle : 120 -140 Mm Long, Non-toxic Plastic 6. Shape : Shovel-shaped 7. Color : Silver 8. The Item Must Have Good Quality 9. Packed In Carton Box 367.00 23,488.00 192 Pc Service Forks. Type : Service Fork Body Shape: Fork Shape Material/appearance: Stainless Steel, Highly Polished, W/ Palin Design Over-all Length: 220 Mm - 260 Mm Width: 20 - 25 Mm Handle Thickness: 1.5 Mm - 4 Mm Handle Length - 165 Mm - 185 Mm 4 Tines, Color: Silver. Packed In Plastic Pouch 125.00 24,000.00 192 Pc Service Tray. Type: Plastic Body Shape: Rectangular Material: Plastic (pp) Size : 14 Inches X 18 Inches X 1 Inch (minimum) Color : Any, Packed In Plastic Pouch The Item Must Have Good Quality 628.00 120,576.00 192 Pc Show/service/base Plates 11" To 14" . Type: Plain Type Body Shape: Round Material: Porcelain With No Design Supply Must Be A Set Consisting (1) Of Each: - 11 Inches, - 12 Inches, - 13 Inches, And - 14 Inches Plates Color: White. Diameter, Inner : 225 Mm - 250 Mm Thickness: 3mm - 6 Mm. Smooth And Glossy Surfaces 574.00 110,208.00 384 Pc Side Plates Or Bread Plates 6" .type: Plain Type Body Shape: Round Material: Porcelain With No Design Color: White Inner Diameter: 95 Mm To 120 Mm Outer Diameter: 145 Mm To 170 Mm Thickness : 3 Mm - 6mm Smooth And Glossy Surfaces Packed In Carton Box. The Item Must Have Good Quality 135.00 51,840.00 192 Pc Side Towels. Type: Chef's Towel Body Shape: Rectangular Material: Oxford Polyester Soft Cloth Over-all Length : 640 - 680 Mm Over-all Width : 420 -460 Mm Color : Plain White Packed In Plastic Pouch. The Item Must Have Good Quality 280.00 53,760.00 192 Pc Silver Platter. Type: Steel Type Body Shape: Round Material: Stainless Steel Diameter: 300 -330 Mm Thickness: 1 - 2 Mm Packed In Plastic Pouch The Item Must Have Good Quality 578.00 110,976.00 96 Pc Soup Ladle. Type: Steel Type Body Shape: Circular Material: Stainless Steel, Highly Polished Appearance Over-all Length : 220 -235 Mm Ladle Bowl Details : 60 -65 Mm Long, 60 -75 Mm Diameter, 10 -15 Mm Deep Handle Details : 145 - 155 Mm Long X 12 - 25 Mm Wide X 1.5 -3 Mm Thick Color : Silver With Hang Hole For Hanging And Easy Access 355.00 34,080.00 384 Pc Soup Bowl. Type: Plain With Two Handles Body Shape: Circular Material : Porcelain Capacity : 24 Oz. (minimum) Packed In Carton Box The Item Must Have Good Quality Packed In A Carton Box 165.00 63,360.00 96 Pc Soup Tureen . Type: Steel Body Shape: Round Material: Stainless Steel Capacity: 7 - 11 Quart Size : 60 X 35 X 32 Cm (minimum) Packed In Plastic Pouch The Item Must Have Good Quality 2,955.00 283,680.00 384 Pc Spoon, Dessert. Type : Dessert Spoon Body Shape: Oval Material/appearance: Stainless Steel, Highly Polished With Plain Design Over-all Length : 175 To 190 Mm Thickness : 2 Mm - 3 Mm Shorter Handle : 120 -130 Mm Color : Silver. Packed In Plastic Pouch The Item Must Have Good Quality 85.00 32,640.00 192 Pc Spoons, Service. Type : Service Spoon Body Shape: Oval Material: Stainless Steel, Highly Polished, W/ Plain Design Over-all Length: 220 Mm - 250 Mm Width: 30 - 38 Mm Handle Thickness: 1.5 Mm - 4 Mm Handle Length - 165 Mm - 185 Mm Color: Silver. Packed In Plastic Pouch The Item Must Have Good Quality 78.00 14,976.00 384 Pc Spoons, Soup (cream And Consume). Type: Soup Spoon Body Shape: Round Material/appearance : Stainless Steel, Highly Polished, W/ Plain Design, Rounded Tip Handle Over-all Length : 165 Mm - 200 Mm Smaller Oval Shaped Spoon Bowl And Tapers Slightly To The Tip Shorter Handle : 110 Mm - 170 Mm Thickness : 1.5 Mm - 3 Mm Color : Silver. Packed In Plastic Pouch 65.00 24,960.00 384 Pc Knife, Steak. Type: Steak Knife Body Shape: Flat With Serrated Edge Material: Stainless Steel Blade With Wooden Handle Length: 170 Mm To 203 Mm Handle Wood Thickness: 10 - 14 Mm With Serrated Blade Packed In Carton Box The Item Must Have Good Quality 269.00 103,296.00 80 Pc Sugar Container. Type: Glass Type Body Shape: Round Material: Glass With Brass Lid (or Equivalent) Diameter: 70 -80 Mm Height: 130 -140 Mm Capacity: 12 Oz. Packed In Carton Box The Item Must Have Good Quality 250.00 20,000.00 128 Pc Table Cloth, 54 X 54 Inches. Type: Plain Cloth Body Shape: Square Material: Oxford Polyester Cloth Color: Plain White Dimension: L 54 Inches X W 54 Inches (minimum) Packed In Plastic Pouch The Item Must Have Good Quality 1,729.00 221,312.00 640 Pc Table Napkins, Cloth, 16 X 16. Type: Plain Cloth Body Shape: Square Material: Oxford Polyester Cloth Or Its Equivalent Size: L 16 Inches X W 16 Inches (minimum) Color: Plain White Packed In Plastic Pouch The Item Must Have Good Quality 225.00 144,000.00 128 Pc Table Skirting Cloth 90" X 90" . Type: Plain Cloth Body Shape: Square Material: American Cotton Twill Cloth Color: Any Color Except Black Dimension: 90 Inches X 90 Inches (minimum) Packed In Plastic Pouch The Item Must Have Good Quality 2,256.00 288,768.00 96 Pc Table, Square/rectangular (6's). Type: Foldable Plastic Body Shape: Square/rectangle Materia: High Density Polyethylene Table Top Powder Coated Steel Frame Dimension: 37 - 39 X 37 - 39 Inches Color: White Good For 6 Persons Packed In Carton Box The Item Must Have Good Quality 9,000.00 864,000.00 32 Pc Tea Pot, 2 Pints. Type: Porcelain Type Body Shape: Round With Handle And Pouring Spout Material : Porcelain Capacity : (2 Pint) Color : White Packed In Carton Box The Item Must Be Of Good Quality 1,040.00 33,280.00 384 Pc Teaspoon. Type : Tea Spoon Body Shape: Oval Tip Material/appearance: Stainless Steel, Highly Polished, W/ Plain Design Over-all Length: 120 Mm To 140 Mm Handle Thickness: 2 Mm To 4 Mm Short Handle Length - 100 Mm (minimum) Color: Silver Packed In Plastic Pouch The Item Must Have Good Quality 85.00 32,640.00 32 Pc Tong, 8 Inches. Type: Tong, 8 Inches Body Shape: Standard Material: Stainless Steel Size: 8 Inches Stainless-steel Arms With Soft, Comfortable Grips Nylon Heads Safe For Nonstick Cookware Heat-resistant Up To 400 Degrees Fahrenheit Tongs Lock Closed For Storage Preferably With A Packing Case Food Grade And Dishwasher-safe. Must Be Branded 324.00 10,368.00 64 Pc Tooth Pick Holder. Type: Steel Type Body Shape: Round Material: Stainless Steel, Highly Polished In Appearance Diameter: 30 -35 Mm Diameter (minimum) Height: 65 -75 Mm Capacity: 1.24 Oz. (minimum) Packed In Plastic Pouch The Item Must Have Good Quality 265.00 16,960.00 64 Pc Tray Stand. Type: Foldable Body Shape: Rectangular Material: Chrome Plated Metal Folding Tray Stand Length: 470 -490 Mm Width: 400 -440 Mm Height: 770 -790 Mm Packed In Plastic Pouch The Item Must Have Good Quality 3,850.00 246,400.00 64 Pc Tray, Bill Folders/change. 1. Material : Heavy Duty Plastic ( Abs ) Or Its Equivalent 2. Height : 190 - 220 Mm 3. Width : 120 -140 Mm 4. Thickness : 2 Mm To 3 Mm (minimum) 5. Color : Black 6. With Check And Pen Holder 7. The Item Must Have Good Quality 8. Packed In Plastic Pouch 356.00 22,784.00 128 Pc Tray, Round (bar). Type: Plastic Body Shape: Round Material: ( Pe/abs) Plastic Rubberized Surface, Non-slip/grip Tight Over-all Diameter: 345 -360 Mm (minimum) Thickness: 2 - 4 Mm (minimum) Color: Black Packed In Plastic Pouch The Item Must Have Good Quality 426.00 54,528.00 384 Pc Water Goblet. Type: Water Goblet Body Shape: Balloon-shaped Bowl Material: Crystal Clear Glass Over-all Length: 200 -220 Mm Capacity: 270 Ml To 300 Ml Rim Diameter - 55 -65 Mm Thickness: 1 Mm To 3 Mm Stem Length : 75 -85 Mm Stem Diameter : 6 -8 Mm Base Thickness : 3 -4 Mm Base Diameter : 7 -80 Mm Packed In Carton Box 145.00 55,680.00 96 Pc Water Pitcher. Type: Steel Type Body Shape: Circular Material: Stainless Steel, Highly Polished Appearance Height: 170 Mm To 220 Mm Top Diameter: 110 -120 Mm (approximate) Capacity: 1 - 1.5 Liter With Pour Spout Dishwasher Safe Packed In Plastic Pouch The Item Must Have Good Quality 485.00 46,560.00 80 Pc Table, Working. Type: Working Table, Stainless Steel Body Shape: Rectangular Material: 304 Stainless Steel, 1.29 Mm Thick (gauge 16) Minimum Length: 1220 Mm (minimum) Width: 700 Mm (minimum) Height: 850 Mm (minimum) Tubular Stainless Steel Legs, 38mm (minimum) With 4 Adjustable Bullet Feet Fully Welded Construction Thickness: Gauge 16 (1.29 Mm Thick) Minimum Stainless Steel Table Top With Stainless Steel Undershelf Distance Between Table Top And Undershelf Is 650 Mm (minimum) Preferably With A Packing Case Or Crate No Sharp Edges And Rough Surfaces Must Be Branded 19,500.04 1,560,003.20 36 Pc Body Brush, Prosthetic. Material: Stiff Nylon Bristle Size: At Least 41.8 Cm X 6.5 Cm (over-all Size) Brush Height: 8mm(minimum) With Wooden Handle" 480.00 17,280.00 36 Pc Bowl, Mixing, Plastic. Material: Plastic Inner Diameter: 10.5 Cm (minimum) Height: 6cm (minimum) Thickness Is 2mm (minimum) Any Color Non-toxic 250.00 9,000.00 18 Pc Bowl, Shampoo. Bowl Material: Abs Plastic With Adjustable Stand(height: 39 Inches To 54 Inches ) Minimum Bowl Dimensions: 19 Inches(l) X 20 Inches(w) X 10 Inches(h); With Sealed Foam Rubber Neck Rest For Shampoo Bowls With Hose Attachment Of 7 Ft. Long(minimum) Stainless Steel Frame. Portable Type. Packed With Shipping Carton Box. Branded 4,000.00 72,000.00 36 Box Box, Hairpin. Material: Metal Size: At Least 3.5 X 4.5 X 0.5 Inches With Ball Tips Packaging: 100 Pcs Per Box Color: Black Non-corrosive 200.00 7,200.00 36 Pc Brush, Applicator. Material: Plastic Non-toxic Size: Small=190mm Length Medium=270mm Large=300mm Handle Width:70mm (minimum) Width Of Tip: 80mm (minimum) With Hair Coloring Dyeing Board Packed With Plastic Pouch 250.00 9,000.00 36 Pc Brush, Hair. Material: Plastic Bristle Paddle Brush Type Wooden Handle Minimum Width: 2 Inches Non-toxic Packed With Protective Carton Box 250.00 9,000.00 36 Pc Cap, Frosting, With Hook. Cap Material: Silicone Type: Reusable, Perforated Cap One Size Fits All Or At Least 31cm X 22cm With Pre-cut Tipping Guides With Bleed Proof Inner Liner With A Rounded Metal Hook To Pull Hair Through The Ready-made Perforations Packed With Plastic Pouch 350.00 12,600.00 36 Pc Cap, Heating. Waterproof Cloth Material. Cordless Type To Fit An Average Size Head (21-24 Inches) Stretch Up To 29 Inches Unisex Hair Care Treatment Styling Reversible And Reusable, Non-toxic Includes With User's Guide In English That Contains: A. Diagram Of The Parts With Their Names B. Operating Procedure On How To Use The Equipment C. Safety Precaution When Using The Equipment D. Basic Troubleshooting And Maintenance Procedure 400.00 14,400.00 36 Pc Cape. Polyester Cloth Size: At Least 125 Cm X 140 Cm Hairstyling Type Non-toxic Packed With Plastic Pouch 220.00 7,920.00 36 Pc Chair, High. Bar Stool Material: Metal, Painted With Anti-rust Width Of The Chair :15 Inches Minimum Height :33 Inches (minimum) Synthetic Leather Seat Material Barstool Crown Back Type With Rubber Ring Of Barstool For Anti-skidding 6,000.00 216,000.00 36 Pc Chair, Hydraulic. Material: Metal Base Size: Length59 Cm, Width54 Cm, Height From 51-78cm Hydraulic Pump Can Be Up And Down By Pedaling Load Capacity:180kg Hydraulic Styling Chair Type Heavy Duty Hydraulic Pump For Height Adjustable And 360' Rotation Hydraulic Pump Build In For Adjusting The Seating Height. With Footrest 8,000.00 288,000.00 36 Pc Clamp. Material: Plastic Overall Length: 9.5cm Thickness:10mm(minimum) Hairstyling Clamp Type 200.00 7,200.00 36 Box Clamp, Duck Bill. Material: Metal Length: 11 Cm (minimum) High Elasticity Stainless Steel Spring. Nonslip Handle Packed With Plastic Pouch Branded 200.00 7,200.00 18 Box Clipper, Hair. Body Material: Hard Plastic Blade Material: Carbon Steel Capacity:6 Watts (minimum) Complete With Blade Guard And 4 Comb Attachments (#1, #2, #3, #4) Motor: Magnetic Type, Corded,12v Ac/dc Adaptor Delivers 1,400 Strokes Per Minute, With Complete Accessories Including The Cleaning Brush With Cord 2 Meters Length Minimum With User's Manual In English Which Includes: A. Parts Manual With Labels, B. Assembly Instructions, C. Operating Procedures, Packed With Protective Carton Box. Branded 2,500.00 45,000.00 36 Pc Comb, Afro. Material: Plastic Size: Overall Length At Least 7 Inches Width: 3.25 Inches(minimum) Number Of Teeth: 12 Teeth (minimum); Teeth Height: 2.5 Inches Long (minimum) 200.00 7,200.00 36 Pc Comb, All Purpose. Material: Plastic Size#3 Or At Least 18 Cm Long (minimum) Has Both Fine And Medium Teeth Position On One Side Only Height Of The Teeth: 2 Cm (minimum) Non-toxic. Packed With Plastic Pouch 200.00 7,200.00 36 Pc Comb, Haircutting. Material: Hard Plastic Length Including The Handle:180mm (minimum) Width: 30mm (minimum) With Detachable Steel Blades And Blade Holder With Two Sides For Different Cuts With Extra Blades 200.00 7,200.00 36 Pc Comb, Large Toothed. Material: Plastic Size: At Least 15 Cm Number Of Teeth: 10 Teeth (minimum) Gap Between Comb's Teeth: 0.4 To 0.5 Cm Gap From One Another Teeth Size: At Least 0.3 Cm In Width X 4cm In Length Non-toxic. Packed With Plastic Pouch 200.00 7,200.00 36 Pc Comb, Tail. Material: Plastic Size : 8 Inches(l)minimum X 1 Inches (w) Minimum Tail Length: 4 Inches(minimum) Tooth Length: 3/4 Inch(minimum) Packed With Plastic Pouch 200.00 7,200.00 36 Pc Comb, Teasing. Material: Plastic With 2 Rows Of Teeth. 1st Row: Large Teeth With At Least 25 Mm Long 2nd Row: Small Teeth With At Least 19 Mm Long Over-all Comb Size: 20 Cm (l) Minimum X 3.8 Cm (w) Minimum. Non-toxic. Packed With Plastic Pouch 200.00 7,200.00 36 Pc Comb, Wide Tooth. Material: Plastic Size: At Least 15 Cm Number Of Teeth: 10 Teeth (minimum) Gap Between Comb's Teeth: 0.4 To 0.5 Cm Gap From One Another Teeth Size: At Least 0.3 Cm In Width X 4cm In Length 200.00 7,200.00 18 Box Crimpers. Power: 25 Watts(minimum) Size: At Least 38 Cm X 15.5 Cm X 9 Cm Maximum Temperature: 200 Degrees Centigrade With Variable Heat Setting. With On/off Switch Button Rated Voltage: 110 -230volts Ac With Power Cord With Plastic Handle 2,000.00 36,000.00 36 Pc Curling Iron. Ceramic Curling Iron Capacity: 65watts Voltage: 210-240volts Ac With Power Cord Barrel Size: 1 Inch (minimum) Adjustable Heat Setting With Maximum Temperature Of 200 Degrees, Centigrade Swivel Cord Up To 360 Degree 3,000.00 108,000.00 36 Pc Drip Pan. Material: Hard Plastic Size: At Least 17.5 X 25.8 X 1 Inches Thickness: 1/8 Inch (minimum) Shallow Rectangular Type Packed With Carton Box 220.00 7,920.00 36 Pc Dryer, Hair. Power: 1000w Rated Voltage: 220vac At Least (l X W X H): 18.5cm X 16cm X 6.5cm With Plastic Handle Design Packed With Carton Box With Styrofoam Holder With User's Manual In English 3,000.00 108,000.00 36 Box Gloves, Disposable. Material: Plastic Size: At Least 25cm X 23cm Packaging Is 100 Pcs Per Box 250.00 9,000.00 36 Box Gloves, Rubber. Size: Medium Thickness: 4 Mil Acid Resistant Packed With Plastic Pouch In Pairs. 250.00 9,000.00 36 Pc Gown, Smock. Material: Polyester Sizes: 1 Piece = Small Size, At Least (50 Inches X 56 Inches); 1 Piece= Medium Size, At Least (52 Inches X 58 Inches); 1 Piece= Large Size, At Least (54 Inches X 60 Inches); Packed With Plastic Pouch Per Size 250.00 9,000.00 36 Box Hairclips. Material: Metal Size: At Least 67mm X 19mm Non-corrosive Packed With Plastic Pouch 180.00 6,480.00 36 Pc Hairnet, Invisible. Material: Nylon Size: 55mm (minimum) Stretchable And Unisex Type Color: Black Non-toxic Packed With Plastic Pouch 180.00 6,480.00 36 Pc Headband. Size: 6 Inches (minimum) Woven Crochet Tube Top Headband Very Stretchy, Soft Material, Comfortable And Breathable 180.00 6,480.00 36 Pc Headband, Flannel. Flannel Cloth Size : At Least 45 Cm (unstretched Circumference) Width: 8 Cm (minimum) 180.00 6,480.00 36 Pc Infrared Iron. Material: Ionic Ceramic Tourmaline-infused Plates And Abs Plastic Body Power: 70 Watts (minimum) Power Rating: 220-240 Volts Ac; Over-all Size: 24 Cm Long (minimum) Heating Plate Size Up To 50 Mm Heating Time: Within 30 Seconds; Variable Heat Settings: From 250 To 450 Degrees Fahrenheit With Digital Temperature Control Safety Mode: Auto Shut Off After 60 Minutes; With Swivel Cord Comes With Storage Pouch. Branded 1,900.00 68,400.00 60 Pc Mirror, Hand. Mirror Size 15 Cm Diameter (minimum) Frame Thickness Including Mirror Glass: 6.5mm(minimum) Over-all Length With The Handle Is 20 Cm (minimum) Clear Mirror With No Distortion Frame And Handle Are Made Of Plastic Plane Mirror Type Packed With Carton Box With Styrofoam Protection 505.00 30,300.00 36 Pc Mirror, Modular. Mirror Type: Plain Mirror Mirror Material: Glass Frame Material: Aluminum (cut To Fit) Dimensions (hxw): 75 Cm X 65 Cm (minimum) Mirror Thickness: 6mm (minimum) 2,300.00 82,800.00 36 Pc Prong Clip, Double. Material: Steel Nickel Or Chrome Base Plated Size: 45 Mm Minimum Hairstyling Clip Type Packed With Plastic Handle 220.00 7,920.00 36 Pc Prong Clip, Single. Material: Steel, Plated Size: 55 Mm (minimum) Type: Single-prong Clip Packed With Plastic Pouch 220.00 7,920.00 36 Pc Razor, Straight. Blade Material: High Carbon Steel Type: Foldable Straight Razor, Replaceable Blade; Dimensions (lxw): 14 Cm X 2 Cm (minimum) When Folded; Compatible With Double-edged Razor Blades; Package Includes 10 Pieces Blade/box Non-corrosive. Branded 300.00 10,800.00 36 Pc Roller Pins. Material: Metal Size: 60mm Long (minimum) Application: Hair Roller Pins Quantity By Dozen(12 Pieces) Non Corrosive. Packed With Plastic Pouch 200.00 7,200.00 36 Pc Rollers, Jumbo. Material: Plastic Approximately 44mm In Diameter X 64mm Long 300.00 10,800.00 36 Pc Rollers, Large Sized. Material: Plastic Size: At Least 40mm Diameter X 60mm Long Hairstyling Type. Packed With Plastic Pouch 250.00 9,000.00 36 Pc Rollers, Medium Sized. Material: Plastic; Diameter: 38 Mm(minimum) Length: 58mm (minimum) Hairstyling Type. Packed With Plastic Pouch 200.00 7,200.00 36 Pc Scissors, Cutting. Material:stainless Steel Total Length: 17cm (minimum) Blade Width At Least 10 Cm. Non Corrosive Packed With Plastic Pouch. Branded 500.00 18,000.00 36 Pc Scissors, Thinning. Blade Material: High Carbon Steel Blade Length At Least 6cm With Straight Blade Type Style: Right Handed Scissor Total Length At Least 17cm One Side Comb Cutter, Non Corrosive Packed With Plastic Pouch. Branded 500.00 18,000.00 36 Pc Scoop. Material: Plastic Capacity:1/2 Cup (minimum) Rounded Edges With Handle Thickness: 1.5 Mm (minimum) 350.00 12,600.00 36 Pc Shower Cap. Material: Plastic Size: One Size Fits All Or 30cm Reusable And Waterproof Packed With Plastic Pouch 220.00 7,920.00 36 Pc Spatula. Material: Plastic Dimension: Over-all Length Of 7.5 Cm Long, X 1.5 Cm Wide (minimum) Application: Hair Waxing Removal Packed With Plastic Pouch 200.00 7,200.00 36 Pc Spray Gun. Material: Transparent Plastic Capacity: 300ml (minimum) Trigger Type Sprayer Dimension: At Least Diameter Of Bottom Is 7 Cm And The Height Is 17cm 220.00 7,920.00 36 Pc Steamer, Hair. Power 450 Watts (minimum) Rating Is 220 Volts/50-60hz Hood Material: Polycarbonate Hood Has At Least 30 Cm Diameter Opening X 25 Cm Deep Timer Setting Is Up To 60 Minutes With At Least 32 Ounce Water Reservoir Adjustable Height From 100 To 150cm With At Least 5 Swivel Caster With User's Manual In English Which Includes: A. Parts Manual With Labels, B. Assembly Instructions, C. Operating Procedures. Branded 6,500.00 234,000.00 36 Pc Stool. Material: Metal, Electroplated Load Capacity: 150kg Design: Swivel Stool With Backrest With Hydraulic Lift To Adjust Height Freely. With Thick Sponge Cushion. With At Least Four Caster Wheels. With Thick Sponge Cushion. Swivel Stool With Backrest No Sharp Edges. Branded 8,500.00 306,000.00 21 Pc Dummy, Anatomical. 1. Half Life-size Muscular Figure Measures 32" Tall (minimum). 2. This Model Features 27 Removable Parts That Are Held On By Metal Screws, Posts, And Hooks. 3. It Shows The Muscular System With Numbered Parts That Comes With A Corresponding Key. 4. It Has Removable Arms, A Removable Calvarium, And A Removable Chest Plate That Hides The Individual Numbered Organs Of The Digestive System 5. Detachable Muscles Include: Deltoid, Brachioradialis With Extensor Carpi Radialis Longus And Brevis, Biceps Brachii, Pronator Teres With Palmaris Longus And Flexor Carpi Radialis, Sartorius Muscle, Rectus Femoris, Extensor Digitorum Longus, Tensor Faciae Latae, Gluteus Maximus, Biceps Femoris, Semitendinosus, Gastrocnemius, Soleus. 6. Removable Organs Include: Brain (2parts), Lungs (2 Parts), Heart (2 Parts, Liver, Intestines, Stomach 7. Base Is 13" X 9" (removable) 8. Weighs 12 Lbs. (approximately) 9. Plastic Material 10. Non-toxic Material 11. Carton Box Packaging 6,000.00 126,000.00 35 Pc Massage Bed / Table. Materials: Hard Wood With Steel Bracings, Hardwood Frame, Marine Plywood Deck; Color: Black Dimensions: W:75 Cm X L:183 Cm X H: (adjustable) Height: Adjustable From 24 In. - 33in. Leg Thickness - 35mm (minimum) Cushion System: High Density Foam (7.5 Cm / 2.95") Minimum With Pu Leather Cover (1mm Thick) Finishing: Round Corner Weight Capacity: 250 Kg(minimum) Gross Weight: 21 Kg (approximate) 2 End Support Bearer To Strengthen The Base And Increase Weight Capacity Accessories - Aluminum Headrest (adjustable) + Face Plug + Armrest + Arm Sling + Carry Case. Portable And Foldable 15,000.00 525,000.00 35 Pc Massage Chair. Ii 1. Padded With 3" Thick, High-density, Small-cell Foam 2. Size: 14"-diameter Seat (minimum) But Without Back And Arm Rest, With Metal Post And Hard Plastic Star. 3. Pneumatic Spring Will Effortlessly Adjust The Height From 18" To 24" With The Pull Of A Lever 4. Five Heavy-duty, Smooth-rolling Wheels 5. Load Capacity: 265 Lbs / 120 Kg (maximum) 6. Smooth Surface And No Sharp Edges 7. Any Color With One Color Only For Whole Lot 5,000.00 175,000.00 35 Pc Sphygmomanometer. Aneroid Type; (for Adult Use) Large Cuff Sizes: 33 To 42 Cm Arm Diameters Accuracy: ±3mm Hg; Measurement Range : 0mm Hg To 300mm Hg; Smallest Scale: 1mm Hg Index And Range Markings On The Dial For Clear Readings Nylon Cuff Is Durable And Stain Resistant With A Velcro Closure Inflation System Is Latex Free And Has An Easy-release Deflation Valve Chrome-plated Brass Air Release Valve; Set Includes: 1 Unit Sphygmomanometer; 1 Zippered Nylon Carrying Case Smooth Surface And Edges, Non-toxic Material 2,500.00 87,500.00 35 Pc Stethoscope. Chest-piece Description: Stainless Steel Double Chest Piece Color: Black Tubing Description: Y-tube Pvc Uses Extra Soft Replaceable And Pivotable Ear Tips The Binaural Is Chromium-plated Chest-piece Diameter: 44 Mm (minimum) And Has Non-chill Rim Overall Length: 29" /74 Cm (minimum) The Stethoscope Is Latex-free Comes With A Pair Of Replacement Ear Tips, A Replacement Membrane, And A Name Plate Smooth Surface And No Sharp Edges 6,829.20 239,022.00 21 Pc Talking Sphygmomanometer. Type: Arm Type Blood Pressure Monitor (talking English), Nylon Cuff Sizes: 33 To 42 Cm Arm Dia. Lcd Digital Display: Systolic, Diastolic, Pulse Rate With Real Voice, Loud And Clear, Announcing Blood Pressure Automatically When Reading Is Detected And Displayed Simultaneously Dimensions: 98mm*126mm*60mm (approximate) Hard Plastic Casing, Smooth Surface And No Sharp Edges, Non-toxic Materials Measurement Range : 0mm Hg To 300mm Hg; Smallest Scale: 1mm Hg Weight: 450g (approximate) Pressure Measurement Range: 20~280mmhg(0.4kpa-37.3kpa) Pressure Accuracy: ±3mmhg(±0.4kpa) Pulse Measurement Range: 40 ~199 Beats /min Voltage: 4*aaa Alkaline Batteries Or Power Adapter Certificate: Ce Rohs Intelligent Automatic Pressurization And Decompression Incorrect Prompting Function Automatic Shutdown: 1 Min After Last Operation Carton Box Packaging 3,500.00 73,500.00 21 Pc Talking Thermometer. Case Material: Hard Plastic Sensing Unit: Thermistor Measurement Method: Actual Measurement Measurement Range: 32 C - 42 C (89.6f-107.6f) Measurement Accuracy: ± 0.1c 32c-42.0c (± 0.2 F 89.6.9f-107.6f) Power Supply: 1.5v Dc, Lr41 Alkaline-magnesium Button Battery Real Voice (loud And Clear In English) Announces Temperature Automatically When Reading Is Detected Temperature Display: 3-digit, +deg C (deg F) Display In 0.1 Degree Increment Dimension Approx.: 2.0 (w) X 4.4 (h) X 1.2 (d) Inches (not Including Probe) / 51 (w) X 110 (h) X 30 (d) Mms (not Including Probe) Choices In Degrees Celsius Or Fahrenheit Talk Button Repeats Last Temperature Reading Last Reading Memory Auto Switch Off Accessories: Protective Case, 5 Probe Covers, Instruction Sheet Paddle Shape With Sensor On Small End 2,599.00 54,579.00 35 Pc Thermometer, Digital. Case Material: Hard Plastic Sensing Unit: Thermistor Measurement Method: Actual Measurement Measurement Range: 32 C - 42 C (89.6f-107.6f) Measurement Accuracy: ± 0.1c 32c-42.0c (± 0.2 F 89.6.9f-107.6f) Power Supply: 1.5v Dc, 1 Lr41 Alkaline-magnesium Button Battery When Measured At A Standard Room Temperature Of 23 Deg C (73.4 Deg F) In A Test Tank Held At Constant Temperature Power Consumption: 0.1mw Low Battery Indication: Battery Symbol Displayed Temperature Display: 3-digit, +deg C (deg F) Display In 0.1 Degree Increment Memory: Last Measuring Reading Beeper Function: 1 Beep When Power On 3 Beeps After Measurement Completed External Size (mm): 19.4(w) × 132.5 (l) × 10.0(d) Accessories: Protective Case, Test Battery, 5 Probe Covers, Instruction Sheet Paddle Shape With Sensor On Small End 2,599.00 90,965.00 21 Pc White Board. White Board, Floor Standing, Rolling Board: White Formica Laminated, Plane Will Not Deform. Board Size: Rectangular 1800mm W X 1000 To 1200mm H, Board Edges Secured With Aluminum Clip Edging 17 Mm (minimum) With Plastic Corner Caps Comes With Metal Tray For Marker And Eraser The Stand And Frame Are Constructed With Aluminum Or Powder Coated Steel 25mm Square Tube (minimum), Sturdy, No Wobble With 4 Lockable Hard Plastic Caster Wheels Overall Height From Floor: 210 To 214cm Smooth Surface, No Sharp Edges 800.00 16,800.00 30 Set Allen, Wrench. 1. Material: Chrome Vanadium Steel, Hrc 38 To 60; 2. Set Of 10 Pieces: 1.5 Mm, 2 Mm, 2.5 Mm, 3 Mm, 4 Mm, 5 Mm, 5.5 Mm, 6 Mm, 8 Mm, 10 Mm; 3. With Holder/ring To Keep The Set Intact; 4. Label Of Sizes Engraved In Each Allen Wrench; 5. Smooth Surfaces And No Sharp Edges 6. Plastic Pack By Set 550.00 16,500.00 30 Pc Anti-static Device (anti-static Wrist Strap). Consists Of: A) Adjustable And Elastic Wristband With Integrated 1 Mega Ohm Resistor, B) Banana Plug With Alligator Clip For Connecting To Ground (or Equivalent), C) At Least 59" Long Coiled Cord; D) Non Toxic Material E) Carton Box Or Plastic Pouch Packaging 1,200.00 36,000.00 60 Pc Combination Pliers, 8". Type: Combination Pliers; Body Shape: Square Nose Material: Chrome Vanadium/forged Steel Length: 9 Inches (minimum) Insulation Range: 1000 Volts (etched On The Handle) Design: Square Nose With Serrated Jaw Comes With Nickel Plated Finish, Side Cutter And Insulated Handle Must Be Branded (brand Must Etched Either In The Head Or On The Handle) 550.00 33,000.00 60 Pc Crimping Tool (rj 11/45). 1. Ratchet Crimp Tool 2. All-in-one Tool That Can Strip, Cut, And Crimp 3. Lightweight Steel Frame 4. Rj-11/45 Compatible 5. Positions For 8p/8c, 6p/6c And 4c Connectors 6. Lightweight, Compact, And Durable 7. Smooth Surface And No Sharp Edges Except Cutting Edges 8. Carton Box Packaging 658.00 39,480.00 18 Pc Desoldering Pump. 1. Material : Plastic Or Aluminum Housing; 2. Replaceable Heat-resistant Plastic Tip; 3. Length : Minimum Of 6 Inches; 4. Effective In Removing Solder; 5. Smooth Surface And No Sharp Edges 6. Carton Or Plastic Packaging 3,000.00 54,000.00 12 Pc Electric Drill, Portable. Type: Electric Power Material: Hard Plastic Rated Voltage: 220 / 240 Volts, Ac 60 Hz Power In Watts: 550 To 650 Watts Speed: Variable Speed Chuck Capacity: 2 To 13 Mm Power Cord Must Have Flat Blade Attachment Plug (type A Plug) Comes With Hss Drill Bits: 2mm 4pcs. 4 Mm 4pcs. 6 Mm 4pcs. 8 Mm 4pcs. 10 Mm 4pcs.12 Mm 4pcs. 12.5 Mm 4pcs. Total- (28 Pcs) Masonry Drill Bits; 4 Mm 2pcs. 6 Mm 2pcs.8 Mm 2pcs. 10 Mm 2pcs. 12 Mm 2pcs. Total- ( 10 Pcs.) With Hammer Function For Concrete Drilling Comes With English User's Manual Includes Of The Following: A. A Diagram Of The Parts With Label; B. Assembly Instructions; C. Operating Procedures; D. Safety Precautions When Using The Equipment; E. Basic Troubleshooting And Maintenance Procedures. Warranty Period Of Parts And Service: 1 Year 4,500.00 54,000.00 12 Pc External Optical Drive. 1. Interface: Usb 3.0 Or Better; 2. Compatibility: Windows 2000, Xp, Vista, 7, 8, 10, Apple Mac, Linux Or Better; 3. Read Speed: At Least 8x Dvd, At Least 24x Cd; 4. Write Speed: At Least 4x Dvd, At Least 16x Cd; 5. Package Includes: A) 1 X External Optical Drive, B) 1 X Usb Power Cable, C) 1 X Usb Data Cable, 6. Item Size: 5.4"x 5.51"x0.63"(l X W X H) Approximate 7. Metal Or Hard Plastic Casing 8. Smooth Surface And No Sharp Edges 9. Carton Box Packaging 10. With User's Manual In English Which Includes: A. A Diagram Of The Parts With Their Names, B. Operating Procedures 11. With Service Centers Located In Major Cities In The Philippines. 2,000.00 24,000.00 60 Pc Flash Drive. 1. Capacity: 64 Gb ; 2. Connectivity: Usb 3.0, Backward-compatible With Usb 2.0, Plug And Play ; 3. Device/os Compatibility: Windows Vista, Windows 7, 8, 10, Mac Os 10.6+ Or Later Versions; 4. Form: Swivel Type Or With Cover; 5. Dimension: 0.40 X 0.80 X 2.31 In. (10.16 X 20.32 X 58.67 Mm) Approximate 6. Metal Or Hard Plastic Casing 7. Smooth Surface And No Sharp Edges 8. Carton And/or Plastic Packaging 9. User's Guide On Name Of Parts, Connection Guide, Maintenance And Safety Precautions. 800.00 48,000.00 60 Pc Flashlight, Head-mounted. 1. Type: Rechargeable, Head Mounted Led Flashlight; 2. Minimum Of 160 Lumens; 3. Beam Distance: Minimum Of 150 Meters; 4. Includes 220 V Ac Charger/power Adaptor (or Equivalent); 5. Charging Time: 3-6 Hours; 6. Provides Up To 30 Hours (minimum) Of Constant Light On A Single Full Charge; 7. Approximate Size: 60x 30mm 8. Smooth Surface And No Sharp Edges 9. Carton Box Or Plastic Pouch Packaging. 10. With User's Manual In English 450.00 27,000.00 60 Pc Hub/switch. 1. Standards And Protocols: Ieee 802.3, Ieee802.3u, Ieee802.3x Csma/cd 2. Interface: 8 10/100mbps Ports, Auto-negotiation, Auto-mdi/mdix 3. External Power Supply Adapter: 100 240vac,50/60hz 4. Fanless 5. Data Rates: 10/100mbps At Half Duplex ; 20/200mbps At Full Duplex 6.led Indicator: Power, 1, 2, 3, 4, 5, 6, 7, 8 7.dimensions: 5.3 X 3.1 X 0.9 In. (134.5 X 79 X 22.5mm) (approx.) 8. Transfer Method: Store And Forward 9. Advance Functions: Green Technolgy, Saving Power Up To 73%; 802.3x Flow Control, Back Pressure; Auto-uplink Every Port 10. Certification: Fcc, Ce, Rohs 6,790.00 407,400.00 30 Pc Lan Cable Tester. 1 Cable Tester With Led Indication For Rj12, Rj11, Rj45, Cat5e, Cat5, 10/100 Base - T. 2 Main Tester: 1-2-3-4-5-6-7-8-g; 3 Remote Tester: 1-4-3-2-5-6-7-8-g; 4 Power Supply: 9 V Battery (included); 5 Capable Of Testing Crossover, Straight-through, And Rollover Cables; 6 Includes Plastic Case Or Pouch; 7 With User's Manual In English 4,500.00 135,000.00 60 Pc Long Nose Pliers, 8". 1 Material: Chrome Vanadium Steel, Hrc 38 To 60; 2 Length: 7 Inches (minimum); 3 Handle Type: Curved Handle With Rubber Cushion For Easy Grip; 4 Jaws Type: Knurled And Long Tempered; 5 Comes With Hardened Cutting Edges And Chrome-nickel Finish. 6. Smooth Surface And No Sharp Edges 7. Carton Or Plastic Packaging 550.00 33,000.00 60 Pc Multimeter, Digital. Material: Plastic Casing Main Functions: Auto Range/data Hold/back Light/ Led Lamp/diode Test/triode Test/continuity/ Over Load Protection/low Battery Indication/auto Power Off/short-circuit Protection. Display: True Rms, 6000 Counts, 3 5/6 Digits Overload Display: Display Ol Dc Voltage:600mv/6v/60v/600v(0.5%+3), 1000v (0.5%+3) Ac Voltage:600mv/6v/60v/600v/750v (0.8%+5) Dc Current:600a/6000a/60ma/600ma/10a (1.2%+3) Ac Current:600a/6000a/60ma/600ma/10a (1.5%+3) Resistance:600/6k/60k/600k/(1.0%+3) ,6m/60m (1.5%+3) Capacitance: 10nf/100nf/1000nf/10uf/100uf/1000uf (4.0%+5), 10mf/100mf(5.0%+5) 1,000.00 60,000.00 120 Pc Patch Panel (48 Ports). 1. Network Patch Panel 2. 48 Port Patch Panel 3. Cat6 Cable 4. Material: Abs Plastic 5. Application: Utp(unshielded) 6. Certification: Rohs, Iso, Ce 7. Rj45 Connector : Two Rows (1-24 Ports & 25-48 Ports) 8. Transport Package: 1pcs/box 9. Smooth Surface And No Sharp Edges 6,950.00 834,000.00 6 Pc Pc Video Camera. 1) 5.0 Mega Pixel Web Camera, Usb-type; 2) With Microphone For Laptop And Desktop Pc Use; 3) Resolution: At Least 640 X 480; 4) Support Windows Xp/7/8/equivalent Mac Os Or Later Versions; 5) With User's Manual In English Which Includes: A) A Diagram Of The Parts With Their Names, B) Operating Procedures C) Basic Troubleshooting And Maintenance Procedures. 6) Hard Plastic Or Metal Casing 7) Smooth Surface And No Sharp Edges 7,000.00 42,000.00 30 Pc Philip's Screwdriver, 8" Insulated. 1. Shank Material: Chrome Vanadium Steel, Hrc 38 To 60; 2. Handle Material: Molded Plastic 3. Overall Length: 8 Inches (minimum) 4. Insulation Protection (including Shank): 1000vac/ 1500vdc, Vde Certified (or Its Equivalent) 5.non Slip Handle Design 6. Carton Or Plastic Packaging 400.00 12,000.00 30 Pc Precision Screwdriver, 8" Insulated. 1. Material: Hardened And Tempered Steel; 2. 1 Set Comes With The Following: A) 3 X Phillips Tip No. 00, 0, And 1 ; B) 6 X Standard Tip No. 1, 1.2, 1.4, 1.8, 2.4, And 3.0; C) 1 X Awl; D) 1 X Magnet; E) Plastic Storage Case; 3. Non Slip Design Handle 400.00 12,000.00 30 Pc Soldering Iron, 60w. 1. Type: Iron Rod 2. Voltage: 220/240vac, 60hz, Single Phase; 3. Power: 60w (minimum); 4. Body Length: 8.3 Inches (21 Cm) Approximate 5. Cord Length: 1.5 Meters (minimum) 6. Handle: Plastic; (non Slip Handle) 7. With User's Manual Written In English That Contains User's Guide, Operating Procedure, Parts With Description, Safety Procedure, And Maintenance; 8. Interchangeable Copper Tip; 9. Should Have Available Spare Parts Nationwide For A Minimum Period Of 5 Years; 10. Carton And/or Plastic Packaging 1,670.00 50,100.00 30 Pc Standard Screwdriver (flat), 8" Insulated. 1. Shank Material: Chrome Vanadium Steel, Hrc 38 To 60; 2. Handle Material: Molded Plastic 3. Overall Length: 8 Inches (minimum) 4. Insulation Protection (including Shank): 1000v, Vde Certified (or Its Equivalent) 5.non Slip Handle Design 6. Carton Or Plastic Packaging 550.00 16,500.00 30 Pc Uninterruptible Power Supply (ups). The Item Shall Have The Following Specifications: 1. Type: Battery (included): Lithium-ion Battery Or Maintenance-free Sealed Lead-acid Battery With Suspended Electrolyte: Leakproof 2. Voltage: Nominal Input Voltage: 230v, 50/60 Hz 3. Output Power Capacity: 600va (minimum) 4. Output Connections :2 Universal Receptacle (minimum) 5. Cord Length: 1 Meter (minimum) 8,000.00 240,000.00 6 Pc Usb External Hd. 1) 1tb Portable/external Hard Drive 2) Application: Laptop / Desktop Pc 3) Interface Type: Sataii 4) Installation: Mobile 5) Formatted Capacity: 1000gb(windows Display About 298gb) 6) Size(mm): 14.29 X 80.01 X 17.60 (approx.) 7) Metal Casing 2,500.00 15,000.00 30 Pc Wire Stripper. Type: Spring-loaded Self-opening; Body Shape: Long Jaw With Slot Blade Material: Hardened Alloy Steel (sharp Edges To Strip And Cut The Wires) Wires To Be Stripped: 10 Awg To 24 Awg Length: 7 Inches (minimum) Comes With Automatic Self- Adjusting Spring, Crimping Slot, And Hard 275.00 8,250.00 60 Pc Wireless Access Point. Type: Wireless Access Point Dual Band Wifi Band / Data Transfer Rate: 867 Mbps At 5 Ghz And 300 Mbps At 2.4 Ghz Band Operating Modes: Access Point (ap), Bridge, Wireless Client, Repeater Interface: One 10/100m Ethernet Port(rj45), Support Passive Poe Power On/off Button And Reset Button Comes With External Power Supply: 5vdc-12vdc / 0.5a-1.0a Dimensions ( L X W X D ): (76-191 ×47-125 ×30-68mm) 3,489.60 209,376.00 Total 22,623,009.00 2. The Department Of Education, Schools Division Office Of Albay Now Invites Bids For The Above-cited Procurement Opportunity. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders In The Amount Of Php 25,000.00 Pursuant To The Latest Guidelines Issued By The Gppb. Delivery Of The Goods Is Thirty (30) Calendar Days From The Date Of The Ntp. Delivery Should Be At The Designated Schools (door-to-door Delivery). Bidders Should Have Completed, Within Five (5) Years From The Date Of Submission And Receipt Of Bids, A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii. Instructions To Bidders. 3. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using A Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) 9184, Otherwise Known As The “government Procurement Reform Act”. Bidding Is Restricted To Filipino Citizens/sole Proprietorships, Partnerships, Or Organizations With At Least Sixty Percent (60%) Interest Or Outstanding Capital Stock Belonging To Citizens Of The Philippines, And To Citizens Or Organizations Of A Country The Laws Or Regulations Of Which Grant Similar Rights Or Privileges To Filipino Citizens, Pursuant To Ra 5183. 4. Interested Bidders May Obtain Further Information From Department Of Education, Schools Division Office Of Albay, Bids And Awards Committee Office, And Inspect The Bidding Documents At The Address Given Below From Monday To Friday During Office Hours (8:00 Am To 5:00 Pm). 5. A Complete Set Of Bidding Documents May Be Acquired By Interested Bidders On November 13 To December 3, 2024; 9:00 Am From The Address Below And Upon Payment Of Php 25,000.00 As The Applicable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb. It May Also Be Downloaded Free Of Charge From The Website Of The Philippine Government Electronic Procurement System (philgeps) And The Website Of The Procuring Entity (www.depedalbay.com) Starting November 13, 2024 Provided That Bidders Shall Pay The Applicable Fee For The Bidding Documents Not Later Than The Submission Of Their Bids. 6. The Department Of Education, Schools Division Office Of Albay Will Hold A Pre-bid Conference On November 20, 2024; 9:00 Am At 2f Lobby, Deped Sdo Albay, Ligñon Hill, Bogtong, Legazpi City, Which Shall Be Opened To Qualified Prospective Bidders. 7. Bids Must Be Duly Received By The Bac Secretariat At The Address Below On Or Before December 3, 2024; 9:00 Am. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb. Bid Opening Shall Be On December 3, 2024; 9:00 Am At 2f Lobby, Deped Sdo Albay, Ligñon Hill, Bogtong, Legazpi City. Bids Will Be Opened In The Presence Of The Bidders’ Representatives Who Choose To Attend At The Address Below. Late Bids Shall Not Be Accepted. 8. Prospective Bidders Are Strongly Encouraged To Order Or Download The Electronic Copy Of The Bidding Documents From The Philgeps Website, For Them To Be Included In The Document Request List Of The Project. The Bidding Documents May Be Viewed Also At The Deped Sdo Albay Schools Division Office Website: Www.depedalbay.com. 9. The Department Of Education, Schools Division Office Of Albay Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Section 41 Of Ra 9184 And Its Irr, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 10. For Further Information, Please Refer To: Jade O. Alberto Education Program Supervisor Bac Secretariat Head-designate Office Of The Bids And Awards Committee 2nd Floor, Deped Sdo Albay, Ligñon Hill, Bogtong, Legazpi City Tel.no.: 052-204-8535 11. You May Visit The Following Websites: For Downloading Of Bidding Documents: Www.depedalbay.com November 12, 2024 (sgd.) Bernie C. Despabiladero, Edd Assistant Schools Division Superintendent Bac Chairperson For Goods And Consulting Services

Details: Description Invitation To Bid The Iligan City Government Bids And Awards Committee (bac), Through Gen Fund-20% / Dev. Fund, Intend To Apply The Sum Of P 3,864,056.67 Being The Approved Budget For The Contract (abc) To Payments Under The Contract For Repair / Renovation Of Tourism Building (bahay Salakot), Buhanginan Hills, Brgy. Pala-o, Iligan City With Project No. Cb(b)-24-139 (ceo-infra). Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. The Iligan City Government Bids And Awards Committee Now Invites For The Supply And Delivery Of Items Below-stated: Particulars Repair / Renovation Of Tourism Building (bahay Salakot), Buhanginan Hills, Brgy. Pala-o, Iligan City General Requirements •installation Of Project Billboard •occupational Safety And Health Program •mobilization And Demobilization •provision Of Field Office For The Engineer - Standard Engineer Field Camp, Office Table And Chair - Computer For Field Engineer Removal Of Structures And Obstruction •demolition Of Concrete Slab For Excavation Of Septic Tank •demolition Of Existing Chs Walls At Main Office (for W-04 •demolition Of Existing Drywall Partitions At Office •chipping Of Existing Toilet Tiles •removal Of Existing Windows And Doors •dismantling Of Existing Plumbing Appliances And Fixtures •demolition Of Kitchen Counter At Basement Earthworks •excavation Work For Septic Tank •gravel Bedding For Septic Tank •backfilling Of Common Soil Using Excavated Soil Must Be Compacted Layer By Layer Concrete Work, Formwork & Scaffolding •septic Tank •kitchen Sink Countertop Masonry Works •4” Reinforced Chs Wall @ Main Office •4” Reinforced Chs Wall @ Main Office Cr •4” Reinforced Chs Wall @ Basement Cr •4” Reinforced Chs Wall For Septic Tank Plastering Works •plaster-topping @ Priv. Rm & Printing Rm. •plaster Chs Wall On Both Sides @ Main Office •plaster Chs Wall On Both Sides @ Main Office Cr •plaster Chs Wall On Both Sides @ Basement Cr •plaster Chs Wall On One Side For Septic Tank Steel Reinforcements •10mm Dia. Rebars For Septic Tank's Masonry & Concrete Works •10mm Dia. Rebars For Additional Chs Walls Architectural Works •installation Of Wallpaper In Antique Gray Brick For Accent Wall •installation Of Solihiya Screen In Wood Framing •fabrication Of “viva Turismo Lligan” Acrylic Logo •installation Of Skirting Board/ Based Board Painting Works •semi-gloss Interior Paint Finish •flat Latex Paint- Primer For Ceiling Board •flat Latex Paint- Off-white Ceiling Finish @ Office •semi-gloss Paint- Off-white Ceiling Finish @ Both Toilet Ceiling Works •6mm Gypsum Board On Double Furring Framing @ 2nf Floor And Basement Toilet •9mm Gypsum Board On Double Furring Framing @ Main Office Built-ins And Cabinets •fabricate 1.475m X 2.4m- 3 Layers Shelves With 2 Door Cabinet And Drawers •fabricate 1.25m X 2.675m Overhead Shelf •fabricate 0.4 X 0.4 X 2.65m Ficem Board Plant Box •fabricate 0.5m X 0.5m X 1.2m Lavatory Counter Cabinet With Ceramic Tile Countertop •fabricate 1.45m X 1.05m 2 Layer Overhead Document Shelf Fabricate 0.6m X 1.45m Built-in Table Waterproofing •cementitious Waterproofing @ Toilet- Walls (5.13 Sqm) •cementitious Waterproofing @ Toilet- Flooring (5.42 Sqm) Tile Works •detachable Green Carpet (8.15 Sqm) •30cm X 60cm Non-slip Floor Tiles @ 2f Toilet •60cm X 60cm Non-slip Floor Tiles @ Basement Toilet •parquet Tiles- For The Demolished Walls •60cm X 60cm Dark Gray Carpet Tiles •300mm X 300mm Ceramic Wall Tiles @ 2f Toilet •200mm X 600mm Ceramic Wall Tiles @ Basement Toilet Electrical Works •installation Of Conduits , Junction Box , Utility Box •installation Of New Electrical Wire , Switches , Aircon Outlet •lnstallation Of Lighting Fixture According The Electrical Plan . Wood Balustrades And Handrail •top Railing: 75x25mm Solid Wood In Wood Stained Finish •balusters: 75x75mm Solid Wood In Wood Stained Finish Plumbing Works •installation Of Pvc Pipes ( Soil And Waste ) And G.i. Pipes For Water •installation Of Water Closets, Lavatory And Faucets •installation Of Kitchen Sink At Pantry Doors And Windows •remove And Replace Existing Doors, See Plan For Details •remove And Replace Existing Windows, See Plan For Details I.general Requirements A . Project Billboard (q = 1.00 Lot) Includes 4' X 8' Tarpaulin, 8' X 8' Tarpaulin, 2"x3"x 14" Coco Lumber, 2"x3"x10" Coco Lumber, 2"x2"x8" Coco Lumber, Assorted Sizes C.w. Nails. B. Occupational Safety And Health Program (q = 1.00 Lot) Includes Safety Shoes, Safety Helmet, Safety Gloves, Specialized Ppe. C.mobilization / Demobilization (q = 1.00 Lot) D. Facilities For The Engineer (q = 1.00 Lot) Includes Field Office For The Field Engineer: 4" X 4" Cocolumber, 2" X 4" Cocolumber, 2" X 3" Cocolumber, 2" X 2" Cocolumber, 1/4" Thk. Ord. Plywood, Ga 300 X 10' Corr.g.i. Sheet, Portland Cement, Washed Sand, Washed Gravel,4" Chb 700 Psi, 10mm Dsb, No. 16 G.i. Tie Wire, Assorted Sizes C.w. Nails, Empty Drum/ Fixtures, Monobloc Chairs, Office Table. Ii.removal Of Structures And Obstruction (q = 1.00 Lot) Includes Demolition Of Existing Chb Walls At Main Office (for W-04), Demolition Of Existing Drywall Partitions At Office, Chipping Of Existing Toilet Tiles, Removal Of Existing Windows And Doors, Dismantling Of Existing Plumbing Appliances And Fixtures, Demolition Of Kitchen Counter At Basement. Iii. Earthworks (q = 7.56 Cu.m.) Includes Excavation Works For Additional Septic Tank, Washed Gravel. Iv.concrete Works And Formworks (q = 2.02 Cu.m.) Includes Portland Cement, Washed Sand, Washed Gravel, Marine Plywood 12mm Thk. X 4' X 8', 2" X 3" X 8' Coco Lumber, 2" X 2" X 8' Coco Lumber, Assorted Sizes C.w. Nails. V.masonry Works (q = 48.54 Sq.m) Includes 4" Chb 350psi, Portland Cement, Washed Sand. Vi.plastering Works (q = 82.80 Sq.m) Includes Portland Cement, Washed Sand. Vii. Steel Reinforcements (q = 1.00 Lot) Includes 10mm Dia X 6m Rebar, No. 16 G.i. Tie Wire. Viii. Wood Balustrades And Handrail (q = 1.00 Lot) Includes Top Railing: 75x25mm Solid Wood In Wood Stained Finish, Balusters: 75x75mm Solid Wood In Wood Stained Finish, Paint Varnish, Paint Brush 2-1/2",assorted Sizes C.w. Nails. Ix.doors And Windows (q = 1.00 Lot) Includes D1- 3.2m X2.8m Brown Powder Coated Aluminum Framing W/ 10mm Clear Fixed Glass And Sliding Door With Complete Accessories; D2- 3.35m X2.55m Brown Powder Coated Aluminum Framing W/ 10mm Clear Fixed Glass And Sliding Door With Complete Accessories; D3- 0.7m X 2.1m Hollow Pvc Door With Door Jamb And Complete Accessories; D4- 0.8m X 2.1m Hollow Core Hdf Door With Door Jamb And Complete Accessories; D5- 0.7m X 2.4m Pocket Door: Solid Wood Door With 2mm X 5mm Grooves And Complete Accessories; D6- 0.7m X 2.1m Hollow Pvc Door With Door Jamb And Complete Accessories; W1- 2.345 X 1.2m Sliding Glass Window W/ Wooden Louver Casement Window: Sliding Window : 1x1" Brown Powder Coated Aluminum Frame, 2x2" Aluminum Mullions, 0.5x0.5" Aluminum Window Grilles, 6mm Clear Tempered Glass; Window Shutters: 4-panel Wooden Louvered Window Shutters, 2x2" Wood Framing; W2- 1.2m X 0.6m Black Powder Coated Aluminum Frame W/ 10mm Clear Glass Awning Window; W3- 0.7m X 2.1m Brown Powder Coated Aluminum Frame W/ 10mm Clear Glass Fixed Window; W4- 2.32m X 0.5m Louver Window : Brown Powder Coated Aluminum Frame W/ 5mm Clear Glass Blades; W5- 0.6m X 0.5m Black Powder Coated Aluminum Frame W/ 10mm Clear Glass Awning Window; W6- 4.7m X 1.27m Sliding Glass Window Casement Window X " Brown Powder Coated Aluminum Frame, 2x2" Aluminum Mullions, 0.5x0.5" Aluminum Window Grilles, 6mm Clear Tempered Glass; W7- 0.845m X 1.27m Fixed Glass Window Casement Window Sliding Window: 1x1" Brown Powder Coated Aluminum Frame, 2x2" Aluminum Mullions, 0.5x0.5" Aluminum Window Grilles, 6mm Clear Tempered Glass X.architectural Works (q = 1.00 Lot) Includes Wallpaper In Antique Gray Brick 15cm X 60cm, Wood Glue, M X 2.8m Solihiya Screen Partition In 2"x2" Wood Framing, M X 2.8m Solihiya Screen Partition In 2"x2" Wood Framing, 4.4m X 0.4m Solihiya Screen Partition In 2"xl" Wood Framing, "viva Turismo Ligan" Acylic Logo, Skirting Board/ Based Boardlin. X 4in. X8ft. Xi.painting Works (q = 209.8225 Sq.m) Includes Permacoat Flat Latex, Masonry Putty, Paint Brush 2-1/ 2 ",brush Roller (152mm), Sand Paper, Assorted Sizes, Tape Fiberglass Mesh (48mm X 30m), Gypsum Putty (5kg/gal), 2" X 3" X 8' Coco Lumber, 2" X 2" X 8' Coco Lumber, Assorted Sizes C.w. Nails. Xii.ceiling Works (q = 90.41 Sq.m) Includes 6mm Thick Gypsum Board 4'x8'; 9mm Thick Gypsum Board 4'x8'; Double Furring, 0.50mm Thk. X 19 X 50 X 19 X 5.00m; Channel Clip; Wall Angle 25 X 25 X 0.4 Mm (3m); Blind Rivets, 1000pcs/box; Riveter. Xiii.built-ins And Cabinets (q = 1.00 Lot) Includes 1.475m X 2.4m- 3 Layers Shelves With 2 Door Cabinet And Drawers, 1.25m X 2.675m Overhead Shelf, 0.4 X 0.4 X 2.65m Ficem Board Plant Box, 0.5m X 0.5m X 1.2m Lavatory Counter Cabinet With Ceramic Tile Countertop, 1.45m X 1.05m 2 Layer Overhead Document Shelf, 0.6m X 1.45m Built-in Table. Xiv.waterproofing (q = 10.55 Sq.m) Includes Portland Cement, Washed Sand, Wire Mesh 3.5mm X 1x1" X 6x20ft, Waterproofing Membrane (4 Kg). Xv.tile Works ( Q = 65.69 Sq.m) Includes Detachable Green Carpet, 300mm X 600mm Ceramic Floor Tiles (non-skid) @ 2f Toilet, 300mm X 300mm Ceramic Wall Tiles @ 2f Toilet, 600mm X 600mm Ceramic Floor Tiles (non-skid) @ Basement Toilet, 200mm X 600mm Ceramic Wall Tiles @ Basement Toilet, Tile Grout (2kg), Tile Adhessive 25kg (heavy Duty), Portland Cement, Washed Sand, Diamond Cutter Wheel, Parquet Tiles- For The Demolished Walls, 0.6m X 2.05m Kitchen Counter In Synthetic Marble Countertop Finish, 60cm X 60cm Dark Gray Carpet Tiles. Xvi.electrical Works ( Q = 1.00 Lot) Includes Electric Wire ,3.5mm2 Thhn Stranded Copper Wire; Electric Wire, 8.0mm2 Thhn Stranded Copper Wire; Electric Wire , 38.0mm2 Thhn Stranded Copper Wire; Switch , 1gang Switch W/led Set 10a 220v; Switch , 2 Gang Switch W/led Set 10a 220v; Switch , 3 Gang Switch W/led Set 10a 220v; Led Downllight 15w; Led Downlight 7w; 10w Rectangular Led Pendant Light Warm Light 1 X 4'; 3w Wall Mounted Led Light Daylight; Duplex Convenience Outlet; Gfci 20a 2 Gang Gfci Safety Outlet; Electrical Tape 3/4" X20yds; Solvent Cement 100cc; Pvc Conduit,15mm X3 Meters; Pvc Conduit Coupling (15mm)dia.; Pvc 90deg Elbow (15mm); Pvc Clamp (15mm) 100pc/pack; Junction Box, Pvc Octagonal W/ Cover 2"x4" Depth Type; Utility Box 2"x3" Depth Type W/ Cover; Circuit Breaker, 15at/50 Af, 2pcb, 230vac Bolt-on Type; Circuit Breaker 20at/50af, 2pcb, 230vac Bolt On Type; Circuit Breaker Soat/soaf, 2pcb, 230vac Bolt On Type; Circuit Breaker 125at/50af, 2pcb, 230vac Bolt On Type Tqd; Panelboard 8 Branches Bolt On Type 2 Pole With Tqd Main Breaker; Enclosure For Main Circuit Breaker 125at Tqd; Service Entrance Cap 25mm Dia. Emt; Emt Clamp (25mm); Tox With Screw Size 10; Emt Connector Set Screw Type 25mm; Emt Elbow 25mm; Cable Tie Black Nylon 100pc/pack; Secondary Rack 2 Pole Insulator; Grounding Rod 5/8" X4.75 Ft. With Clamp. Xvii . Plumbing Works ( Q = 1.00 Lot) Includes Two-piece Water Closet Close Coupled; Wall Hung Lavatory 450x400x140mm; Vessel Type Lavatory 450x400x140mm; Stainless Steel Sink 86x50cm , Heavy Duty; Bidet Spray, Hose & Hook Set Abs Material Chrome Plated 1.2m Hose Length, Heavy Duty;tissue Holder, Heavy Duty; Faucet Lavatory, Heavy Duty; Faucet Kitchen, Heavy Duty; Wall Faucet, Heavy Duty; Floor Strainer 100x150x2.7mm; 7.5 Pm Grease Trap And Accessories; Vanity Mirror For 2nd Floor Toilet; 4" Dia. Pvc Wye; 4" Dia. Pvc Clean Out; 4" Dia. Pvc Elbow, 1/8 Bend; 4" Dia. X 10' Pvc Pipe, S-1000; 2" Dia. Pvc P-trap; 2" Dia. Pvc Wye; 2" Dia. Pvc Tee; 2" Dia. Pvc Clean Out; 2" Dia. Pvc Elbow, 1/8 Bend; 2" Dia. X 10' Pvc Pipe, S-1000; 3 Way Angle Valve; Pvc Cement, 400cc; 1" Dia. G.i. Elbow; 1" Dia. G.i. Tee; " Dia. G.i. Coupling; 1" Dia. G.i. Caps, Banded; 1" Dia. X 20' G.i. Pipe; Teflon Tape (big). Approved Budget For The Contract (abc): P 3,864,056.67 Required Bid Security: 2% Of The Abc If Cash, Manager’s Check; Bank Draft/guarantee, Irrevocable Letter Of Credit Confirmed Or Authenticated By A Universal Or Commercial Bank; And 5% Of The Abc If Surety Bond Callable Upon Demand Issued By A Surety Or Insurance Company Duly Certified By The Insurance Commission As Authorized To Issue Such Security Delivery Period Is Within One Hundred (100) Calendar Days From Receipt Of Notice To Proceed. Bidders Should Have Completed, Within Three (3) Years From The Date Of Submission And Receipt Of Bids, A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii. Instruction To Bidders. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using A Non-discretionary “pass/fail” Criterion As Specified In The Implementing Rules And Regulations (irr) Of Republic Act (ra) 9184, Otherwise Known As The “government Procurement Reform Act”. Bidding Is Restricted To Filipino Citizens/sole Proprietorships, Partnerships, Or Organizations With At Least Sixty Percent (60%) Interest Or Outstanding Capital Stock Belonging To Citizens Of The Philippines, And To Citizens Or Organizations Of A Country The Laws Or Regulations Of Which Grant Similar Rights Or Privileges To Filipino Citizens, Pursuant To Ra 5183 And Subject To Commonwealth Act 138. Interested Bidders May Obtain Further Information From Iligan City Government And Inspect The Bidding Documents During Office Hours From 8:00 A.m. – 12:00 P.m. And 1:00 P.m. – 5:00 P.m. At The Office Of The Bids And Awards Committee, 2nd Floor City Hall Main Bldg., Buhanginan Hills, Pala-o, Iligan City. The Complete Schedule Of Activities Is Listed, As Follows: Activities Schedule 1. Issuance Of Bid Documents: November 19 – December 10, 2024 – 8:00 A.m. At Room 205, Left Wing, 2nd Floor, Sp Bldg., Buhanginan Hills, Palao, Iligan City. 2. Pre-bid Conference: November 26, 2024 – 9:30 A.m. At Casimero P. Cabigon Hall, 2nd Floor City Hall Main Bldg., Buhanginan Hills, Pala-o, Iligan City 3. Submission Of Bids: December 10, 2024 – 9:30 A.m. At Casimero P. Cabigon Hall, 2nd Floor City Hall Main Bldg., Buhanginan Hills, Pala-o, Iligan City 4. Opening Of Bids: December 10, 2024 – 9:30 A.m. At Casimero P. Cabigon Hall, 2nd Floor City Hall Main Bldg., Buhanginan Hills, Pala-o, Iligan City A Complete Set Of Bidding Documents Will Be Available To Prospective Bidders Upon Payment Of A Non-refundable Amount Of P 5,000.00 To The Iligan City Government Cashier, At The Bac Office, 2nd Floor, City Hall Main Building, Buhanginan Hills, Pala-o, Iligan City. The Iligan City Government Reserves The Right To Accept Or Reject Any Bid, To Annul The Bidding Process, And To Reject All Bids At Any Time Prior To Contract Award, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. Furthermore, The City Government Of Iligan Assumes No Responsibility Whatsoever To Compensate Or Indemnify Bidders For Any Expense Or Loss Incurred In The Preparation And Submission Of The Eligibility Statements And Bids. Approved By: (signed)darwin J. Manubag, Phd. Bac Chairman Date Of Advertisement/posting: November 19, 2024 Place Of Posting/advertisement: City Hall/ibjt Bulletin Boards, Iligan Official Website, Phil-geps Itb No. 24-139 (ceo-infra)

Details: Description Gov. Celestino Gallares Multi-specialty Medical Center Invitation To Bid For Supply, Delivery, Installation, Testing And Commissioning Of 4 Lots Various Medical Equipment (batch 2) For Gov. Celestino Gallares Multi-specialty Medical Center 1. The Gov. Celestino Gallares Multi-specialty Medical Center (gcgmsmc), Through The Health Facilities Enhancement Program 2024 Intends To Apply The Sum Of Ninety-two Million Pesos Only (php92,000,000.00) Being The Abc To Payments Under The Contract For Cb-2024-11-0004. Bids Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. The Gcgmsmc, Through The Health Facilities Enhancement Program 2024 Intends To Apply The Sum Of Ninety-two Million Pesos Only (php92,000,000.00) Being The Abc To Payments Under The Contract For Each Lot/item.et Al. Lot No. Item/description Quantity Unit Cost Total Cost 1 Treadmill With Electrocardiogram, Exercise / Stress Testing System + Cardiovascular Information System 1 35,000,000.00 35,000,000.00 2 Portable X-ray Machine 1 17,000,000.00 17,000,000.00 3 Ultrasound Machine 1 20,000,000.00 20,000,000.00 4 Flexible Endoscopy 1 20,000,000.00 20,000,000.00 Grand Total 92,000,000.00 Bids Received In Excess Of The Abc For Each Lot Shall Be Automatically Rejected At Bid Opening. 2. The Gcgmsmc, Now Invites Bids For The Above Procurement Project. Delivery And Installation Of The Goods Is Required Within 120 Calendar Days Upon Receipt Of Notice To Proceed. Bidders Should Have Completed, Within 3 Years From The Date Of Submission And Receipt Of Bids, A Contract Similar To The Project. The Description Of An Eligible Bidder Is Contained In The Bidding Documents, Particularly, In Section Ii (instructions To Bidders). 3. Bidding Will Be Conducted Through Open Competitive Bidding Procedures Using A Non-discretionary “pass/fail” Criterion As Specified In The 2016 Revised Implementing Rules And Regulations (irr) Of Republic Act (ra) No. 9184. A. Bidding Is Restricted To Filipino Citizens/sole Proprietorships, Partnerships, Or Organizations With At Least Sixty Percent (60%) Interest Or Outstanding Capital Stock Belonging To Citizens Of The Philippines, And To Citizens Or Organizations Of A Country The Laws Or Regulations Of Which Grant Similar Rights Or Privileges To Filipino Citizens, Pursuant To Ra No. 5183. 4. Prospective Bidders May Obtain Further Information From Gcgmsmc Through Electronic Mail Via Procurement@cpspecialtycenter.org Or Through The Cellular Number 09209437250. 5. A Complete Set Of Bidding Documents May Be Acquired And Downloaded By Interested Bidders From Gcgmsmc Google Drive From (procurement@cpspecialtycenter.org) On November 15- December 10, 2024 And Upon Payment Of The Applicable Fee For The Bidding Documents, Pursuant To The Latest Guidelines Issued By The Gppb, In The Amount Indicated Below In Accordance With The Following Schedule: Lot No. Item/description Total Cost Bidding Documents Fee (in Philippine Peso) 1 Treadmill With Electrocardiogram, Exercise / Stress Testing System + Cardiovascular Information System 35,000,000.00 25,000.00 2 Portable X-ray Machine 17,000,000.00 25,000.00 3 Ultrasound Machine 20,000,000.00 25,000.00 4 Flexible Endoscopy 20,000,000.00 25,000.00 The Procuring Entity Shall Allow The Bidder To Present Its Proof Of Payment For The Fees Through Online Banking Or Online Deposit With The Following Bank Details: Bank Name: Development Bank Of The Philippines Account Name: Gcg Multi-specialty Medical Complex Account Number: 00-0-15490-780-5 "for Bidders Choosing To Pay Via Online Transfer Or Bank Deposit, Please Ensure That Proof Of Your Successful Transaction Is Promptly Sent To The Procurement Email Address: Procurement@cpspecialtycenter.org. In Compliance With Coa Circular Number 2021-014, Clause 5.2, An Acknowledgement Receipt Will Be Issued As Proof Of Verified And Received Payment. Access To Bidding Documents Will Be Granted Only Upon Presentation Of This Acknowledgement Receipt. 6. The Gcgmsmc Will Hold A Pre-bid Conference On The 27th Day Of November 2024 At 0900h At Room 3c-e310 Located At The 3rd Floor Of Gcgmsmc Building C, Malayo Sur Cortes, Which Shall Be Open To Prospective Bidders. 7. Bids Must Be Duly Received By The Bac Secretariat Through Manual Submission On Or Before The 10th Day Of December 2024 At 0900h At Gcgmsmc Procurement Office Room 3c-w327 Located At The 3rd Floor Of Gcgmsmc Building C, Malayo Sur, Cortes, Bohol. Late Bids Shall Not Be Accepted. 8. All Bids Must Be Accompanied By A Bid Security In Any Of The Acceptable Forms And In The Amount Stated In Itb Clause 14. 9. Bid Opening Shall Be On The 10th Day Of December 2024 At 0900h At Room 3c-e310 Located At The 3rd Floor Of Gcgmsmc Building C, Malayo Sur Cortes. Bids Will Be Opened In The Presence Of The Bidders’ Authorized Representatives Together With Their Company Id. 10. The Gcgmsmc Reserves The Right To Reject Any And All Bids, Declare A Failure Of Bidding, Or Not Award The Contract At Any Time Prior To Contract Award In Accordance With Sections 35.6 And 41 Of The 2016 Revised Irr Of Ra No. 9184, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. 11. Submission Of Hardcopies: The Winning Bidders Shall Submit Their Original Eligibility And Technical Documents Described In Itb Clause 10 In One Sealed Envelope Marked "original - Technical Component", And The Original Of Their Financial Component In Another Sealed Envelope Marked "original Financial Component", Sealing Them All In An Outer Envelope Marked "original Bid". Each Copy Of The First And Second Envelopes Shall Have 2 Copies And Similarly Sealed Duly Marking The Inner Envelopes As "copy No. 1 Technical Component" And "copy No. 1- Financial Component” And "copy No. 2- Technical Component" And "copy No. 2- Financial Component" And The Outer Envelope As "copy No. 1" And "copy No. 2" Respectively. These Envelopes Containing The Original And The Copies Shall Then Be Enclosed In One Single Envelope. Please Take Note That All Notarized Documents Must Be Treated As Original Copies For All The Submitted Documents (original, Copy 1, And Copy 2). It Is Imperative That Each Copy Retains Its Original Notarization To Ensure Legal Validity And Compliance. The Original And The Number Of Copies Of The Bid As Indicated In The Itb Clause 15 Shall Be Typed Or Written In Ink And Shall Be Signed By The Bidder Or Its Duly Authorized Representative/s. All Envelopes Shall: A. Contain The Name Of The Contract To Be Bid In Capital Letters; B. Bear The Name And Address Of The Bidder In Capital Letters; C. Be Addressed To The Procuring Entity's Bac In Accordance With Itb Clause 1; D. Bear The Specific Identification Of This Bidding Process Indicated In The Itb Clause 1. 12. For Further Information, Please Refer To: Mary Grace L. Simbajon Jessa O. Quiñal Procurement Office Procurement Office Malayo Sur, Cortes, Bohol Malayo Sur, Cortes, Bohol Procurement@cpspecialtycenter.org Procurement@cpspecialtycenter.org +639209437250 +639452478632 November 14, 2024 Approved By, (signed) Doreen A. Lugo, Lpt Bac Chairperson Noted By, (signed) Laurence Elliot R. Tirol, Md, Fpcp Medical Center Chief I Head Of Procuring Entity --------------------------------------------------------------------------------------------------------- 1 1 Lot Supply, Delivery, Installation, Testing & Commissioning Of Treadmill With Electrocardiogram, Exercise / Stress Testing System + Cardiovascular Information System Treadmill With Electrocardiogram, Exercise / Stress Testing System Power Supply : Ac Operation; Input Voltage: 200 To 240 Volts Ac; Power Consumption: 350 Watts Max Display : At Least 22 Inch Diagonal Display Size; Resolution: At Least 1680 X 1050 Pixels; Tiltable Height Adjustable Flat Screen For Optimal Positioning Dedicated Workflow Keys Risk Stratification: Critical Algorithms, Including Heart Rate Recovery (hrr) And T-wave Alternans (twa) Functional Response: Metabolic Equivalents (mets) Level Indicated During Procedure Ischemia Detection: St/hr Hysteresis Analysis Which Improves Cad Detection Wireless Acquisition: Use Of Wireless Technology To Obtain Signals Or Data Capable Of Creating A Remote Workstation On Any Pc For Viewing Editing And Printing Stress Data Capable Of Adding Automated Blood Pressure And Oxygen Saturation Data Into The System System Is Capable Of Integrating With Stress Echocardiography, Nuclear Imaging, And Ambulatory Blood Pressure Analysis Open System Architecture Uses Industry Standard Communication Protocols Such As Dicom And Xml; Data Export Via Xml, Pdf And Xls To Match Emr Or His Files Automative Timeout And Log-in For Increased Security Advanced Security Protections Include Data Encryption, Username And Password Authentication, Secure Network Connections, Electronic Delivery Of Security Patches And Updates, Constant Threat Monitoring And Disaster Recovery Plan Weight: Patient Weight Capacity (kg): Up To 227; Treadmill Net Weight (kg): Up To 193 Power Requirements: 220/240 Vac, 1-phase, 50-60 Hertz, 20-amp Power Supply; Must Have Dedicated 15a Service Speed Range: 0.1 To 15.0 Miles Per Hour, 0.2 To 24.0 Kilometers Per Hour; Self-calibrating; Adjustable In 0.1 Mph Or 0.1 Kph Increments Incline Range: 0 To 25%, At Least 0.5% Incremental Movements; Self-calibrating Running Surface: At Least 56 By 160 Centimeters (cm); Running Belt Tracking System; Cushioned Running Deck Absorbs Shock Of Foot Falls; Self-lubricated And Reversible Running Deck; Step-up Low Profile Deck Height: At Least 18 Cm From Floor. Communication Ports: Rs232 Female Serial Port; Usb 1.0 “b” Port. Floor Surface Footprint: At Least 84 By 200 Cm Level Surface. Dual Comparative Speed Sensors Auto Runaway Shutdown Auto Communication Loss Shutdown Manual Twist Lock Emergency Stop Button Manual Stop Tether Braking System For Safe Patient Off-loading Fire Rated Motor Pan Hood Enclosure Cardiovascular Information System The System Shall Allow Cardiac Technologists To Enter Comments Which Will Not Be Reflected In The Report Or Distributed To Electronic Medical Record (emr). The Gui Should Allow Searching In Forms – Quick Search Of Specific Field Name, Label Or Value In Forms With Immediate Link Which Takes The User To The Field And Highlights It For Documentation. The Gui Should Allow Searching For Values Within Reports. The System Should Support Structured Reporting, With Quick Reports, Side By Side Reporting, And Real-time Synchronization Of The Report To Data Fields In The Form. Report Templates Must Be User-definable. The Reporting System Shall Be Able To Auto Populate Findings Where Relevant And The Cardiologist Must Be Able To Override Any Auto Populated Data. The System Should Support Comprehensive Reporting Functions For Structural Heart End-to-end Electrophysiology (ep) Workflow In Conjunction With Ep Recording System In The Market Pediatric Echo Reporting Incorporated With Boston Z-scores The System Should Support Ingestion And Non-editable Display Of Pdf Reports From 3rd Party Systems, Such As Hemodynamic Systems, Including Trackings/full Disclosure From Holter Monitoring Systems Or Ecg Management Systems The System Shall Be Able To Receive Studies Sent Directly From Modalities And Devices (without Drawing From Digital Imaging And Communications In Medicine (dicom) Modality Worklist). The System Shall Be Able To Automatically Create Patients From Received Studies, If The Patient Is Not Yet Available In The System Database. The System Shall Prevent Separate Cardiologists From Simultaneously Reporting On The Same Examination, And Alert The Users. The System Shall Have A Charge Verification And Communication Functionality To Hospital Billing It Systems. The System Should Support Result Distribution In A Variety Of Formats, Including Hl7, Pdf, And Sending Discrete Xml Values To External Systems Embedded Advanced Post-processing Tools For Cath And Us (2d, 3d And 4d) Via Dedicated Ultrasound Reporting System/picture Archive Communication System Embedded 3d Advanced Visualization With Advanced Processing Web-enabled Deployment Cardio Imaging Solution Integration 1280 X 1024 Resolution Particulars Workstation: (1) Unit Windows 10 64bit Or Newer Version X86 Microprocessor, Ram - At Least 32gb Ssd - At Least 512gb, Network - At Least 1gb With Peripheral Component Interconnect Express Slot For Medical Graphic Controller Worklist Monitor: (1) Unit Of At Least 27" Monitor Warranty : 5 Years And On The Graphic Controller, 20,000 Hours Backlight Warranty Guaranteed At 400cd/m2 Calibrated Luminance. Minimum Of Five (5) Year/s For Spare Parts & Service Upon Acceptance By End-user Conduct Free Preventive Maintenance At Least Semi-annually Or According To Manufacturer's Recommendation/s Within Warranty Period. Corrective Maintenance Within A Maximum Of Fourteen (14) Days Upon Notification From End-user; Technical Support Staff Response Time Within At Least Two (2) Hours Via Remote Access Or Maximum Of Twenty-four (24) Hours Either Via Physical Presence On Site. Equipment Down-time Within Warranty Period Due To Inherent Defect/s And/or Fault/s Shall Be Added To The Total Warranty Period Availability Of Support Staff Within Visayas Delivery, Installation, Commissioning, Permit/s, Training And Other Related Expenses Incurred Will Be Shouldered By Winning Bidder, Where Applicable Vendor Must Provide Intensive Operational Or Application Training With Certification/s For End-user/s And Intensive Technical Training For Maintenance/biomedical Staff. Vendor Must Have Existing/active Quality Management System Certification E.g. Ce0123 (medical Device), Or Its Equivalent For Importation, Warehousing, Installation & Servicing Of Active And Non-active Medical Services. Vendor And / Or Manufacturer Must Provide Fda Certificaton: Fda 510(k) K131246 Or Its Equivalent, If Applicable Vendor Shall Agree To Provide Factory Or Principal Manufacturer Training And/or Certification For At Least One (1) In-house Biomedical Technologist Or It Personnel And/or Other End User. Progress Billing And Payment May Be Availed By The Winning Bidder As Follows, Otherwise, Full Payment Is Due At The Completion Of The Project And Requirements: 15% Upon Delivery At Site; 30% Upon Complete Installation, And 55% Upon Completion Of Project And/or Acceptance Of End-user. Vendor Shall Warrant That The Product Supplied Shall Meet The Published Specifications. Vendor Shall Provide No Less Than Five (5) Years Warranty On Each Of The Equipment For Spare Parts And Service Upon Acceptance By End User/s. Vendor Agrees To Provide Free Of Charge All Parts And Labour Necessary To Repair Each Of The Equipment Purchased During The Period Covered By The Warranty And Replacement Of Any Item/s And/or Part/s Found To Be Defective In Material Or Workmanship Under Normal Use. Equipment Shall Be Delivered Complete With All Cabling, Connectors, And All Other Accessories Necessary For Full Operation Of The Equipment, Where Applicable. Vendor Must Certify That All Products Quoted Must Be In Current Production And Publicly Available As Of The Date Of This Tender. Unproven Future Products Shall Not Be Accepted. All Desired Features Listed Must Be In Current Production, Installed And In Use At The Time Of Quote/bid. Equipment Must Meet All Currently Applicable Safety Standards, Local And International Where Applicable. Vendor May Include Post-warranty Comprehensive Preventive Maintenance Program Proposal For The Next 3-4 Years And Must Also Indicate Cost Estimated For Major Spare Part/s. Any And All Components Not Manufactured By The Vendor/primary Manufacturer Shall Be Listed As Such With Name/address/contact Information Of The Manufacturer Supplied. Vendor Shall Provide Automatic Voltage Regulator (avr) And Uninterrupted Power Supply (ups) To Back Up The System. Equipment Shall Be Delivered With At Least Two (2) Copy Of All Service Manuals And At Least Two (2) Copy Of All User Manuals. Certification From The Manufacturer That The Units Are Brand New And Not With Any Issues Or Defect. Vendor Shall Confirm And Certify In Writing That Parts And Labor Will Be Available For The Quoted Equipment For Not Less Than Five (5) Years After The Warranty Period. Principal's/manufacturer's Product Portfolio Must Have Been Present In The Local Market For The Past Ten (10) Years. Equipment Must Be Manufactured By A Known And Reputable Company With Certificate Of Iso 9001:2015 And/or Iso 13485:2016 Or Its Equivalent. Completion Period For Delivery Must Not Exceed 120 Calendar Days And Succeeding Installation Must Not Exceed 120 Calendar Days. Any Deviation From This Limit Requires Prior Approval By The Head Of The Procuring Entity (hope) And Only Applies During Extenuating Circumstances. Completion Period For Delivery Must Not Exceed 120 Calendar Days And Succeeding Installation Must Not Exceed 120 Calendar Days. Any Deviation From This Limit Requires Prior Approval By The Head Of The Procuring Entity (hope) And Only Applies During Extenuating Circumstances. Principal’s / Manufacturer’s Products Must Have Been Present In The Local Market For The Past Ten (10) Years Vendor Shall Provide Integration, Interoperability And Migration Solutions Exclusively Using Filmless Platforms Such As Medical Grade Clinical Monitors, 2d/3d Workstations, Dicom Enabled Printers And Cd/dvd Medical Disc Publishers, Medical Film Digitizers , Dicom Archives, Foresight Analog To Digital Conversion System, Mri Compatible Infusion Pump And Patient Monitor, And Digital Or Suites ----------------------------------------------------------------------------------------------- 2 1 Lot Portable X-ray Machine General Information General Purpose Digital Mobile Xray For Patient In Recumbent And Seated 32 Kw At 100 Kv 100 Ms Large Focus And 16 Kw At 100 Kv 100 Ms Small Focus Non Motorized Examination Can Be Performed By Connecting To The Mainpower Switch 2-axis Counterbalanced Column Arm With 90° Tube Head Rotation And ± 317° Arm Rotation Allows Easy Adjustment For All The Different Projections Generator Power Output: Large Focus: At Least 32 Kw At 100 Kv 100 Ms Small Focus: At Least 16 Kw At 100 Kv 100 Ms Kvp Range: 40 Kv To 150 Kv Mas Range: 0.32 Mas To 200 Mas Kvp Accuracy: < ± 3 Kv (40 Kv To 60 Kv); < ± 5 Kv (60 Kv To 150 Kv) Mas Accuracy: At Least ± 0.1 Mas (0.32 Mas To 2 Mas); ± 6 % (> 2 Mas) Shortest Exposure Time: At Least 1 Ms Max. Exposure Time: At Least 3.2 S Exposure Release: Handswitch With 5 M Coiled Cord Or Infrared Remote Control 1 Protection Against Electric Shock: Class I Acc. To Iec 60601-1 Xray Tube Tube Housing (single Tank With Rotating-anode Tube) Stabilization: Microprocessor-based Adjustment And Regulation During Exposure Focal Spot Nominal Value: Dual (0.6 Mm / 1.2 Mm) Anode Angle: At Least 16° Anode Speed: At Least 180 Hz (high Speed) Heat Storage Capacity Of Tube Housing: At Least 830 Kj (1170 Khu) Heat Storage Capacity Of Anode: At Least 210 Kj (300 Khu) Collimator: Manually Adjustable Multileaf Collimator, Rotatable ± 90° Collimator Light And Light Field Intensity: Led Min. 180 Lux At 1 M Sid Advanced Collimator: Pediatric Filters For Lower Dose Imaging And V-laser For Even More Magnesium-alloy Shell-type Frame Dose Area Product Measurement Chamber Typical Filtration: At Least < 0.4 Mm Al Equivalent Dap Resolution: At Least 0.01 Μgym2 Maximum Measurable Dap: 1 X 105 Μgym2 Flat Panel Wireless Detector Wireless Detector: At Least 35 Cm X 43 Cm (14 In X 17 In) Detector Detector Technology: Csi Scintillator, Amorphous Silicon (a-si) Detector Acquisition Matrix: At Least 2304 X 2800 Pixels (full Iq Performance Area) Pixel Size: At Least 150 Μm Acquisition Depth (gray Scales): At Least 16 Bit Active Area: Up To 34.6 Cm X 42.0 Cm (13.6 In X 16.5 In) Thickness: At Least 15 Mm (0.6 In) Detector Weight: ≤ 3.7 Kg (8.2 Ibs) With Battery Max. Load: At Least 300 Kg (661 Ibs) (patient Lying Down) And At Least 100 Kg (220 Ibs) (patient Standing) Data Transfer: W-lan, 802.11 A/b/g/n/ac Battery Operation Capacity: At Least 8 Hours Operation Time With At Least 320 Images, 1 Image Every 90 Sec And At Least 840 Images In Operation Mode, 1 Image Every 30 Sec. Built-in Rechargeable Battery Battery Operating Time Of At Least 8 Hours Of Continuous Use Charging Location: External Battery Charger Charging Time From Empty State To Full Charge: Within 3 Hours Image Acquisition Image Display: Fit To Window View Of Full Image Image Processing Functions: Rotation, Vertical And Horizontal Flipping, Zoom,windowing For Contrast/brightness, Black/white Image Inversion Graphic Functions: Quantification With Angle Distance Measurement Text Functions: Marking, Annotations, Image Comments, R/l Markers Tube Line Enhancement: Amplified Display Of Tubes And Lines In The Image For Position Control Security: Malware Protection Data Transfer Dicom Network Interfaces: Transmission Of Images To A Dicom Network For Viewing And Archiving Confirmation From The Image Archive Storage Commitment Printing Of Images To A Dicom Laser Camera Via Virtual Film Sheet Retrieval Of Images To A Picture Archival System Get Worklist Function For Importing Patient Data From A Data Management System (ris/his) Cr And Dx Worklist Entries Modality Peroformance Procedure Step Function For Sending Examination Statistics And Dose Information To A Data Management System Sending Of Dose Values For Each Study To An Archiving System Documentation Image Data Management: Export To Usb Device In Jpg, Dicom Dcm Or Dicom Raw Transmission Of Images To Network Automatic And Selective Printing With Virtual Film Sheet Provide- Statistics Of Rejected Images Significant Features Wlan Connectivity For Increase Reach And Improved Connectivity Pediatric Filters Transparent Filters For Lowering The Patient Entry Dose Remote Service That Allows Hardware And Software Diagnosis, Customer Care Service And System Configuration Accessories Radiation Protection Equipment, Such As Lead Gowns, Gonadal Shields, And Thyroid Shields. Vendor Shall Warrant That The Product Supplied Shall Meet The Published Specifications. Warranty Period For Five (5) Years After The Acceptance. Minimum Of Five (5) Year/s For Spare Parts & Service Upon Acceptance By End-user. Vendor Must Repair Or Replace Any Item And/or Part/s Of The Equipment Found To Be Defective In Material Or In Workmanship Under Normal Use, Provided That The Equipment Is In Good Working Condition Thereafter, Within The Warranty Period. Conduct Free Preventive Maintenance At Least Semi-annually Or According To Manufacturer's Recommendation/s Within Warranty Period. Corrective Maintenance Within A Maximum Of Fourteen (14) Days Upon Notification From End-user; Technical Support Staff Response Time Within At Least Two (2) Hours Via Remote Access Or Maximum Of Twenty-four (24) Hours Either Via Physical Presence On Site. Equipment Down-time Within Warranty Period Due To Inherent Defect/s And/or Fault/s Shall Be Added To The Total Warranty Period. Availability Of Support Staff Within Visayas. Delivery, Installation, Commissioning, Permit/s, Training And Other Related Expenses Incurred Will Be Shouldered By Winning Bidder, Where Applicable. Vendor Must Provide Intensive Operational Or Application Training With Certification/s For End-user/s And Intensive Technical Training For Maintenance/ Biomedical Staff. Must Certify The Availability Of Spare Parts For The Next Five (5) Years. Vendor Must Have Existing/active Quality Management System Certification (e.g. Ce0123 Medical Device), Or Its Equivalent For Importation, Warehousing, Installation & Servicing Of Active And Non-active Medical Services. Vendor And / Or Manufacturer Must Provide Fda Certificaton: Fda 510(k) K170476 Or Its Equivalent. Shall Be Delivered With At Least Two (2) Copies Of User Manuals. Vendor Must Certify That All Products Quoted Must Be In Current Production And Publicly Available As Of The Date Of This Tender. Unproven Future Products Shall Not Be Accepted. All Desired Features Listed Must Be In Current Production For At Least 2 Years, Installed And In Use At The Time Of Quote/bid Vendor Shall Agree To Provide Factory Or Principal Manufacturer Training And/or Certification For At Least One (1) In-house Biomedical Technologist Or It Personnel And/or Other End User. Progress Billing And Payment May Be Availed By The Winning Bidder As Follows, Otherwise, Full Payment Is Due At The Completion Of The Project And Requirements: 15% Upon Delivery At Site; 30% Upon Complete Installation, And 55% Upon Completion Of Project And/or Acceptance Of End-user. Completion Period For Delivery Must Not Exceed 120 Calendar Days And Succeeding Installation Must Not Exceed 120 Calendar Days. Any Deviation From This Limit Requires Prior Approval By The Head Of The Procuring Entity (hope) And Only Applies During Extenuating Circumstances. Principal’s / Manufacturer’s Products Must Have Been Present In The Local Market For The Past Ten (10) Years Any And All Components Not Manufactured By The Vendor/primary Manufacturer Shall Be Listed As Such With Name/address/contact Information Of The Manufacturer Supplied Vendor Shall Confirm And Certify In Writing That Parts And Labor Will Be Available For The Quoted System For Not Less Than One (1) Year After The Warranty Period Vendor Shall Provide Integration, Interoperability And Migration Solutions Exclusively Using Filmless Platforms Such As Medical Grade Clinical Monitors, 2d/3d Workstations, Dicom Enabled Printers And Cd/dvd Medical Disc Publishers, Medical Film Digitizers , Dicom Archives, Foresight Analog To Digital Conversion System, Iramed, Mri Compatible Infusion Pump And Patient Monitor, And Digital Or Suites Vendor To Shoulder Any Expenses Related To Delivery, Installation, Commissioning, Permit/s,training And Other Sundries Necessary For The Complete Installation Of The Equipment ------------------------------------------------------------------------------------------------------------ 3 1 Lot Ultrasound Machine Electrical Power Voltage: 100 - 240 Vac Frequency: 50/60 Hz Power Consumption: Maximum Of 0.9 Kva With Peripherals Console Design At Least 4 Active Physical Probe Ports, At Least 1 Inactive Probe Storage Port Wireless Probe Connection, Capable Of Connecting Wireless And Linear Probe. Integrated Ssd (at Least 1 Tb) Integrated Dvd-r Multi Drive On-board Storage Of Thermal Printer With Inclusion Of At Least 10 Rolls Of Thermal Paper Integrated Locking Mechanism That Provides Rolling Lock And Caster Swivel Lock Front And Rear Handles Easily Removable Air Filters Operating System: Windows 10 Enterprise Ltsc 2019 (64-bit) Keyboard Operating Keyboard Adjustable In Height And Rotation Ergonomic Hard Key Layout Interactive Back-lighting Integrated Recording Keys For Remote Control Of Up To 4 Peripheral Devices Or Dicom Devices Integrated Gel Warmer Touch Screen At Least 12-inch High-resolution, Color, Touch, Display Screen Interactive Dynamic Software Menu Brightness Adjustment Key/feature Monitor At Least A 23.8-inch Wide, High-resolution High Definition Unit Display. Can Be Moved At Least 350 Mm (13.7 Inches) Horizontally In Both Directions. Can Be Moved At Least 150 Mm (5.9 Inches) Vertically At Least A 90° Swivel In Both Directions. Fold-down And Lock Mechanism For Transportation Resolution: At Least 1920 X 1080 Pixels. Anti-glare Viewing Angle: 89°/89°/89°/89°. Transducer Type Sector / Phased Array Curved Linear Array Microcurved Linear Array Linear Array Matrix Array (linear) Volume Probes (4d) Split Crystal Transesophageal Echocardiogram (tee) Probe Operating Modes Capability Brightness Mode / 2d Grayscale Motion Mode Color Flow Mode Power Doppler With Directional Map Non Doppler Color Flow For Hemodynamic Study Digital Tgc With 8 Independent Controls System Features Pre-programmable Categories Simplified User Interface For High Volume Workflow Maximum System Bandwidth: 25 Mhz Cine Memory: At Least 1 Gb Connectivity: (a) Can Do Lan Or Wireless (b) Dicom 3.0 (c) Public Sr Template (d) Structured Reporting Compatible With Vascular, Obstetric (ob), Cardiac And Breast Standards (e) Remote Monitoring Scanning Parameters Digital Beamforming;infinite Number Of Effective Channels Frame Rate: At Least 9,000 Hz Displayed Imaging Depth: 0 – 100 Cm Doppler Mode: (a) Prf: 0.4 Khz - 35.5 Khz (b) Velocity Range: ± 10 - 2,870 Cm/s Minimum Depth Of Field: 0 - 2 Cm (zoom) (probe Dependent) Maximum Depth Of Field: 0 – 100 Cm (probe Dependent) Continuous Dynamic Receive Focus Software Features Automatic Optimization Optimize B-mode Image To Help Improve Contrast Resolution With One Button Press Selectable Amount Of Contrast Resolution Improvement (low,medium, High) Continuously Adjusts B-mode Axial And Lateral Gain Uniformity And Overall Gain Level Suppressing The Noise Adjusts Region Of Interest Position, Sample Volume Position, And Steering With One Button Press Capable Of Non Doppler Color Flow For Hemodynamic Study Easy, Fast Visualization Of Tiny Vessels, Displaying As A 3d Effect. Available In Color, Power Doppler And Microvascular Imaging (mvi) Assistant Protocol Workflow Enhancement Tool For Standardized And Repetitive Exams Include Factory Programs User-defined Programs And Import Functionality Steps Include Image Annotations, Mode Transitions, Basic Imaging Controls And Measurement Image Comparison Side-by-side Comparison Of Previous Ultrasound And Other Modality Exams During Live Scanning Strain Elastography Qualitative And Semi-quantitative To Assess The Stiffness Of A Tissues. Should Be Able To Have A Qualitative Graph To Show Consistency Of Compression Available On Convex, Linear And Endovaginal Probe Shear Wave Elastography Quantitative Software For Assessing The Stiffness Of A Tissue. Measured In Kpa Or M/s Or Kpa And M/s With Quality Mode Can Do Multiple Acquisition Of Frames In One Breath Hold Able To Do A Re-measure In The Archives Available On Convex, Linear (low And High Frequency) And Endovaginal Probe Live Steatosis Quantification Able To Quantify Fatty Liver Hepatic Protocol Able To Measure Liver Steatosis And Liver Stiffness At The Same Frame. Able To Capture Multiple Frames In One Breath Hold. Virtual Convex Provides A Convex Field Of View Should Be Compatible To Spatial Compounding Available On All Linear And Sector Transducers Speckle Reduction Imaging High Definition Speckle Reduction Imaging Compatible With Side-by-side Dual-view Display Compatible With All Linear, Convex And Sector Transducers Compatible With B-mode, Color, Contrast Agent And 3d/4d Imaging Pre And Post Processing Panoramic Imaging Allows A Real-time Representation Of Long Anatomical Areas (e.g.patellar Tendon), Can Scan Up To 60 Cm Length Home Page Collection Of User’s Favorite Parameters From Measurement/comments/body Patterns Programmable Buttons Measurement For B/m/doppler User Defined Annotation For Selected Exam Category Continuous Optimization Delivers Continuously Optimized Images With Incredible Uniformity From Near To Far Field Artificial Intilligence (ai) Based Features System Capable That The User To Identify A Lesion In Breast, Thyroid Or Liver Lesion And On One Click, The Ultrasound Will Automatically Trace The Lesion System Capable To Automatically Measure The Fetal Biometry. Can Be Turned On And Off. An Ai Based Software That Automatically Determines The Location Of Vessels Both For Color Doppler And Pulsed Wave (pw) Mode. System Familiarization With The Color Preset For Abdominal Ultrasound. Automatic Measurement Of Kidney For Both Left And Right. Breast Measurement Package A Dedicated Breast-specific Measurement Package That Allows User To Make Labeling, Measuring And Describing Lesion Easy Leverage The Bi-rads Lexicon Criteria/assessment Organizes Multiple Measurements Into A Convenient Worksheet Thyroid Measurement Package Thyroid-specific Measurement Package Enables Labeling, Measuring And Describing Nodules, Lymph Nodes And Parathyroids Multiple Measurements Can Be Organized Into A Convenient Worksheet And Sends Results Via Dicom Sr Auto Intima Media Thickness (imt) Automated Method Of Measuring The Intima Media Thickness Of The Common Carotid Artery (cca) Or Internal Carotid Artery (ica) From Multiple Samples Across A User Defined Length. Photo Assistant Photograph Relevant Anatomy And Include Photos With The Clinical Images Provides Value Context For Documentation And Comparison After A Procedure Utilizes Tablet Or Phone Remote App With The Use Of Android Phone Or Tablet, The Ultrasound System Can Be Utilized Using Major Keys Like Major Modes, Freeze/print, Cursor And Etc Fusion Imaging The System Must Support A Technique That Fuses Two Different Imaging Modalities. For Hepatic Interventions, Real-time Ultrasound (us) Should Be Capable Of Being Fused With Other Imaging Modalities, Including Ct, Mri, And Pet/ct. Convex, Microconvex And Linear Probe To Have An Integrated Gps Tracker When Using The Fusion Feature. Improved Speckle Reduction Imaging Acquire Extraordinary Images Across A Broad Range Of Patients, With Incredible Uniformity From Near- To Far-field And The Penetration Power To Manage High-bmi Patients Efficiently. Micro Vascular Imaging Detects Slow Flow And Small Vessels With New Clutter Filtering, And Can Use Together With The 3d Like Feature Blood Flow. Start Protocol Automatically Select Category, Probe, Preset, Or Scan Assistant From Worklist Exam Description Learn The Category, Probe, Preset, And Scan Assistant Based On Exam Description 3d/4d Ultrasound Three-dimensional Image And Provide An Even Clear Image Of The Baby. Enhanced 3d Image A Skin Like Appearance Of A 3d/4d Image To Better Asses The Structure Of A Fetus. 3d/4d Image Rendering Automate Render Line Placement In 3d/4d Imaging, Enabling Clinicians To Easily Acquire Surface-rendered Images. Probes Convex Probe Application: Abdomen, Ob/gyn, Pediatric, Peripheral Vascular, General Musculoskeletal Bandwidth: 1.0 – 6.0 Mhz Number Of Elements: At Least 192 Field Of View (max.): 80° Cardiac/ Sector Probe Application: Adult Cardiac, Pediatric Cardiac, Adult Cephalic, Abdominal Imaging Bandwidth: 1.0 - 5.0 Mhz Number Of Elements: At Least 288 Field Of View (max.) : 120° Wireless Probe, Convex And Linear Convex Applications: Abdomen, Ob, Peripheral Vascular, General Musculoskeletal, Superficial Musculoskeletal, Cardiac And Pleural Bandwidth: 2 - 5 Mhz Number Of Elements: At Least 128 Field Of View (max.): 67° Linear Applications: Peripheral Vascular, Thyroid, Scrotal, Breast, General Musculoskeletal, Superficial Musculoskeletal, Pediatric Cephalic And Pleural Bandwidth: 3 - 12 Mhz Number Of Elements: At Least 192 Field Of View (max.): 38 Mm Linear Probe 1. Applications: Abdomen, Peripheral Vascular, Neonatal, Pediatric, Neonatal Transcranial, General Musculoskeletal, Superficial Musculoskeletal And Small Parts Inculding Breast, Thyroid And Scrotal 2. Bandwidth: 4.0 – 16.0 Mhz 3. Number Of Elements: At Least 1008 4. Field Of View (max.): 50 Mm Endocavitary Probe 1. Applications: Ob/gyn, Urology 2. Bandwidth 3.0 – 10.0 Mhz 3. Number Of Elements: At Least 192 4. Field Of View (max.): 180° Convex Volume Probe 1. Application: Abdomen, Ob/gyn, Pediatric, Neonatal 2. Bandwidth: 2.0 - 8.0 Mhz 3. Number Of Elements: At Least 192 4. Field Of View (max.): 80° Endocavitary Volume Probe 1. Application: Ob/gyn, Urology 2. Bandwidth: 3.0 - 10.0 Mhz 3. Number Of Elements: At Least 192 4. Field Of View (max.): 180° Vendor Shall Warrant That The Product Supplied Shall Meet The Published Specifications. Vendor Shall Provide (5) Years Warranty For Equipment Covering 1 Probe From 2nd Year To 5th Year Upon Acceptance By End User/s. Vendor Agrees To Provide Free Of Charge All Parts And Labour Necessary To Repair Each Of The Equipment Purchased During The Period Covered By The Warranty And Replacement Of Any Item/s And/or Part/s Found To Be Defective In Material Or Workmanship Under Normal Use. Equipment Shall Be Delivered Complete With All Cabling, Connectors, And All Other Accessories Necessary For Full Operation Of The Equipment, Where Applicable. Vendor Must Certify That All Products Quoted Must Be In Current Production And Publicly Available As Of The Date Of This Tender. Unproven Future Products Shall Not Be Accepted. All Desired Features Listed Must Be In Current Production, Installed And In Use At The Time Of Quote/bid. Conducts Bi-annnual Preventive Maintenance And Calibration With Corresponding Certificates And Stickers Attached To The Unit. Vendor Must Respond With Technical Support Staff, Either Remotely Within Two (2) Hours Or In-person Where Applicable, Within At Least Twenty-four (24) Hours Upon Notification Of End-user; Must Perform Corrective Maintenance Within A Maximum Of Fourteen (14) Days Upon Notification Of End-user; Equipment Must Meet All Currently Applicable Safety Standards, Local And International Where Applicable. Vendor May Include Post-warranty Comprehensive Preventive Maintenance Program Proposal For The Next 3-4 Years And Must Also Indicate Cost Estimated For Major Spare Part/s. Any And All Components Not Manufactured By The Vendor/primary Manufacturer Shall Be Listed As Such With Name/address/contact Information Of The Manufacturer Supplied. Vendor Shall Provide Automatic Voltage Regulator (avr) And Uninterrupted Power Supply (ups) To Back Up The System. Equipment Shall Be Delivered With At Least Two (2) Copy Of All Service Manuals And At Least Two (2) Copy Of All User Manuals. Certification From The Manufacturer That The Units Are Brand New And Not With Any Issues Or Defect. Vendor Shall Confirm And Certify In Writing That Parts And Labor Will Be Available For The Quoted Equipment For Not Less Than Five (5) Years After The Warranty Period. Vendor Shall Provide Comprehensive Training Of Users In Operation, Basic And Advance Maintenance Shall Be Provided With Certificates, Vendor Shall Agree To Provide Factory Or Principal Manufacturer Training And/or Certification For At Least Two (2) In-house Biomedical Technician Or Engineer And End User. Principal's/manufacturer's Product Portfolio Must Have Been Present In The Local Market For The Past Ten (10) Years. Equipment Must Be Manufactured By A Known And Reputable Company With Certificate Of Iso 9001:2015 And Iso 13485:2016 Or Its Equivalent. Progress Billing And Payment May Be Availed By The Winning Bidder As Follows, Otherwise, Full Payment Is Due At The Completion Of The Project And Requirements: 15% Upon Delivery At Site; 30% Upon Complete Installation, And 55% Upon Completion Of Project And/or Acceptance Of End-user. Completion Period For Delivery Must Not Exceed 120 Calendar Days And Succeeding Installation Must Not Exceed 120 Calendar Days. Any Deviation From This Limit Requires Prior Approval By The Head Of The Procuring Entity (hope) And Only Applies During Extenuating Circumstances. -------------------------------------------------------------------------------------------------------- 4 1 Lot Flexible Endoscopy Video Processor High Definition Video Outputs: Digital Visual Interface, Serial Digital Interface, Video Graphics Array Standard Video Outputs: S-video, Composite Video Baseband Signal Hd Video Recording: Built-in Workstation, Data Management & Report Editing After Procedure Can Access Data Management, Report Editing, Image Capture And Hd Video Recording Hard Disk: At Least 500gb Internal Capacity Power Requirement: 220-240 V, 60 Hz Chromoendoscopy Modes: Spectral Focused Imaging, Versatile Intelligent Staining Digital Zoom: 1.4x, 1.6x, 1.8x Color Adjustment: Red, Blue, Chroma, ±15 Levels Patient Data: At Least 10000 Records Lightsource Main Lamp: At Least 4 Light Emitting Diode Lamps With Average Working Hours Of At Least 10,000 Hours With Lifetime Indicator Light Control: Manual And Auto Adjust Air Pump: Off, Low, Mid, High Hot Plugging With Spectral Focused Imaging, Versatile Intelligent Staining With White Light Mode Power Requirement: 220-240 V, 60 Hz Monitor Medical Grade Light Emitting Diode Monitor With At Least 26 Inches Size Resolution: At Least Full Hd 1080p Visual Angle: Horizontal 178° / Vertical 178° Video Signal Input : Digital Visual Interface X1, Video Graphics Array X1, Video X1, Serial Digital Interface X1 Video Signal Output : Digital Visual Interface & Serial Digital Interface Power Requirement: 220-240 V, 60 Hz Trolley With Master Switch And Centralized Power Control With At Least Four (4) Layer Racks With Scope Holders With Built In Automatic Voltage Regulator Gastroscope Depth Of View (mm): 3-100 Field Of View: At Least 140° Distal End Diameter (mm): At Least 9.3 Bending Section Diameter (mm): At Least 9.3 Instrument Channel Diameter (mm): At Least 2.8 Angulations: At Least Up:210°; Down:90°; Left:100°; Right:100° Working Length (mm): At Least 1050 Total Length (mm): At Least 1350 Inclusion Of Distal End Cap Colonoscope Depth Of View (mm): 3-100 Field Of View: At Least 140° Distal End Diameter (mm): At Least 12 Bending Section Diameter (mm): At Least 12.5 Instrument Channel Diameter (mm): At Least 3.8 Angulations: At Least Up:180°; Down:180°; Left:160°; Right:160° Working Length (mm): At Least 1350 Total Length (mm): At Least 1700 Inclusion Of Distal End Cap Particulars Vendor Shall Warrant That The Product Supplied Shall Meet The Published Specifications. Vendor Shall Provide No Less Than Five (5) Years Warranty On Each Of The Equipment For Spare Parts And Service Upon Acceptance By End User/s. Vendor Agrees To Provide Free Of Charge All Parts And Labour Necessary To Repair Each Of The Equipment Purchased During The Period Covered By The Warranty And Replacement Of Any Item/s And/or Part/s Found To Be Defective In Material Or Workmanship Under Normal Use. Equipment Shall Be Delivered Complete With All Cabling, Connectors, And All Other Accessories Necessary For Full Operation Of The Equipment, Where Applicable. Vendor Must Certify That All Products Quoted Must Be In Current Production And Publicly Available As Of The Date Of This Tender. Unproven Future Products Shall Not Be Accepted. All Desired Features Listed Must Be In Current Production, Installed And In Use At The Time Of Quote/bid. Conducts Bi-annual Preventive Maintenance And Calibration With Corresponding Certificates And Stickers Attached To The Unit. Vendor Must Respond With Technical Support Staff, Either Remotely (2 Hours) Or In-person Where Applicable, Within At Least Twenty-four (24) Hours Upon Notification Of End-user; Must Perform Corrective Maintenance Within A Maximum Of Fourteen (14) Days Upon Notification Of End-user. Equipment Must Meet All Currently Applicable Safety Standards, Local And International Where Applicable. Vendor May Include Post-warranty Comprehensive Preventive Maintenance Program Proposal For The Next 3-4 Years And Must Also Indicate Cost Estimated For Major Spare Part/s. Any And All Components Not Manufactured By The Vendor/primary Manufacturer Shall Be Listed As Such With Name/address/contact Information Of The Manufacturer Supplied. Vendor Shall Provide Automatic Voltage Regulator (avr) And Uninterrupted Power Supply (ups) To Back Up The System . Equipment Shall Be Delivered With At Least Two (2) Copy Of All Service Manuals And At Least Two (2) Copy Of All User Manuals. Certification From The Manufacturer That The Units Are Brand New And Not With Any Issues Or Defect. Vendor Shall Confirm And Certify In Writing That Parts And Labor Will Be Available For The Quoted Equipment For Not Less Than Five (5) Years After The Warranty Period. Vendor Shall Provide Comprehensive Training Of Users In Operation, Basic And Advance Maintenance Shall Be Provided With Certificates, Vendor Shall Agree To Provide Factory Or Principal Manufacturer Training And/or Certification For At Least Two (2) In-house Biomedical Technician Or Engineer And/or End User. Principal's/manufacturer's Product Portfolio Must Have Been Present In The Local Market For The Past Ten (10) Years. Equipment Must Be Manufactured By A Known And Reputable Company With Certificate Of Iso 9001:2015 And/or Iso 13485:2016 Or Its Equivalent. Progress Billing And Payment May Be Availed By The Winning Bidder As Follows, Otherwise, Full Payment Is Due At The Completion Of The Project And Requirements: 15% Upon Delivery At Site; 30% Upon Complete Installation, And 55% Upon Completion Of Project And/or Acceptance Of End-user. Completion Period For Delivery Must Not Exceed 120 Calendar Days And Succeeding Installation Must Not Exceed 120 Calendar Days. Any Deviation From This Limit Requires Prior Approval By The Head Of The Procuring Entity (hope) And Only Applies During Extenuating Circumstances.

Details: The subject of the performance of the public contract is the reconstruction of the lighting system using an economical solution thanks to the technology of LED lamps. The lighting system is powered by cable and air lines. Before the implementation itself, traffic safety will be ensured at the place of construction and assembly work. Construction must be coordinated with the owners of the technical infrastructure and the owners of adjacent communications or land. During the reconstruction of the lighting system, the system's power supply will first be disconnected from the distribution network. After that, disassembly of the reconstructed part will be carried out according to the measurement sheet. Within the framework of the reconstruction of the lighting system of ground communications, complete arming of the individual main switchboards is being considered to ensure the proper functioning of the work. Electricity meter switchboards and invoicing measurements in take-off points fed from the NN distribution network must be carried out according to the requirements of the electricity distributor. The Switchgear Must Be Equipped With Fault Protection And Automatic Disconnection From The Source With Protective Grounding And Protective Bonding Under Specified Conditions Must Be Provided. Where it is not possible to achieve automatic disconnection within the required time due to the high impedance of the fault loop, additional bonding must be carried out. The Switchboard Must Be Adapted To Install Limiters To Limit High Inrush Currents Caused By Switching Led Technologies That Must Meet Electromagnetic Compatibility. After the completion of the replacement of all lamps according to the project, a revision report and passporting of public lighting will be made.

Details: The subject of the performance of the public order is the construction of a photovoltaic power plant with a capacity of 99 Kwp, a sports hall and a substation Nn. Fve Power Plant - 180 Photovoltaic Panels with a Power of 550 Wp, Total Installed Power of 99 Kwp, Reserved Power is 99 Kw will be Installed - Flow Monitoring Will Be Set in the Operating Mode of the Inverters, on the Roof Area at a 17° Slope on the Flat Roof of the Hall on a Typical Metal Structure From Profiles. Switchboard NN - On the ground floor there is one room, switchboard NN With installed switchboards, inverters, batteries, lip and cable grates. This Is A Type Container Certified For Use For Fve. The supporting structure consists of steel profiles and sheathing of insulating panels, including protective coating Ral 9002 grey-white. The roofing will be made with one gable roof with a 7° slope. The covering will be made of galvanized sheet metal in gray-white color. The contract will be financed from the Environmental Operational Program 2021-2027, Project Name "Fve installation at the Zš Chýně Gym Building" Registration Number Cz.05.01.02/01/22_011/0001241. The specification of the subject of performance is given in Appendix No. 1 – Project Documentation Including Itemized Budget. Further information is provided in Appendix No. 2 of the Tender Documentation - Contract for the Work.

Details: Description Technical Specifications Engagement Of A Mice Organizer/event Management Service Provider I. Project Title : Dot Annual Yearend Briefing 2024 Component/set-up : Live Onsite Attendance Of 220 Target Participants Implementation Date : 10 December 2024 (depending On Availability Of The Secretary) Venue : Metro Manila (tba Hotel) Concept : Formal Business Procurement : Mice Organizer/ Events Management Company Estimated Cost : Php 422,984.03 Source Of Funds : Opaa Augmented Wfp 2024 Attachments : Cost Basis Ii. Background Tourism’s Role In Economic Resurgence And Sustained Recovery Could Not Be Overemphasized. No Less Than Our President Ferdinand “bongbong” Marcos, Jr. Highlighted Tourism’s Resilient And Reliable Contribution To Sustained Growth In His Recent State Of The Nation Address. According To Him, Tourism Has Historically Provided Livelihood And Employment Opportunities To Filipinos. Given The Importance Placed By Our President To Tourism, We See The High Value And Critical Importance Of Striving For Success In Promoting Tourism To Establish It As A Hallmark Of The Current Administration, And Most Importantly, A Source Of National Pride For Our People. Philippine Economic Managers Have Identified Tourism As The Second Top Driver Of The Philippine Economy In The First Half Of The Current Year. This, Despite Global Tourism Recovery To Pre-pandemic Levels Remains Unrealized According To The United Nations World Tourism Organization. Our President’s Vision For The Philippine Tourism Industry Is Clear: To Establish A Sector Anchored In The Richness Of Filipino Culture, Heritage, And Identity, Making It Competitive On The Global Stage. Together, Through Meaningful Collaboration And Innovation, We Can Transform The Philippines Into A Tourism Powerhouse In Asia, Ensuring Lasting Economic And Social Benefits For All That Will Give More Reasons To Love The Philippines! Iii. Project Description To Maximize The Dot’s Media Exposure And Ensure That Its Public Image Remains Positive, The Opaa Has Been Organizing A Yearend Briefing. Held Annually For The Past Three Years Prior To The Pandemic. This Gathering Of Invited Members Of The National Media And Stakeholders Is Part Of Its Extensive Information And Awareness Drive Program To Position The Department’s Works In Various Media Platforms. The Dot Annual Yearend Media Briefing And Appreciation Reception Aims To Give, First And Foremost, The Tourism Secretary, As Well As Other Key Officials Of The Department The Opportunity To Engage Our Media Partners And Influencers For Their Sustained Efforts In The Promotion Of Philippine Tourism, While Addressing Some Of The Pressing Issues Related To Policy Directions, Targets And Accomplishments Of The Department For The Concluding Year. Sought To Attend Are The Dot-accredited Members Of The National Media And Influencers/ Tourism-beat Reporters, Lifestyle, Travel Editors, Columnists, And News-beat Journalists From Broadsheets, Travel Magazines, Radio, Tv And Social Media. Top Officials Of The Department And Heads Of The Communications Department Of Allied Agencies And Stakeholders Are Also Enjoined To Attend The Event For Networking Purposes. Iv. Project Objectives • Enlist Commitment And Support From The Members Of The National Media In All Department Initiatives, Programs And Directions; • Contribute To Advancing The Vision Of President Bongbong Marcos For A Revitalized Tourism Sector That Heralds The Filipino Brand And Contributes Greatly To The Philippines’ Economic Resurgence. • Engage Members Of Media To Continuously Generate Favorable Publicity For The Department. • Forge An Eloquent Relationship Between And Among Media Platforms. • Engage Public And Private Partnership In Tourism Development And Propagation Of The Culture Of Tourism. V. Gender And Development Objectives ● Promote Equal Opportunities For Men And Women To Receive Recognition As Indispensable Players In The Tourism Industry. Vi. Legal Basis  Republic Act 9593 Or The Tourism Act Of 2009 Mandates The Department Of Tourism (dot) To Encourage Activities And Programs Which Promote Tourism Awareness, Preserve The Country’s Diverse Cultures And Heritage, And Instill A Sense Of History And A Culture Of Tourism Among The Youth And The Populace; Vii. Scope Of Work/deliverables/requirements For Supplier A. Mice Organizer/event Management Service Provider  Production Management - Assist The Dot In The Conceptualization, Management, And Implementation Of The Events Styling And Entertainment Repertoire Plan Which Consists Of The Following:  Emcee/host O To Introduce The Guest Of Honor, Each Segment Of The Program, And Entertainment O Mc/host Should Be Either Male Or Female Duo Who Has Experience In International/ National Events And/or Tv Presenting Experience O Mc/host Must Speak Fluent English And Filipino O Mc/host Should Be Available For Rehearsal 3 Hours Prior To The Event  Entertainment O The Event Requires A Minimum Of 3 Different Entertainment Acts To Perform In Between Segments (beginning, Middle And End) For Approximately 5 Minutes O Entertainers May Include But Are Not Limited To Singers, Performers, Or An Orchestra, And Preferably Those Who Have Performed Before An International Audience In Keeping With The Overall Conceptual Approach And As Approved By Dot. O Entertainers Must Be Available 3 Hours Before The Event For Briefing And Rehearsal. O Artists To Bring Their Equipment And During Rehearsal Connect With The Av Team To Set Up What Is Required. O Entertainment Will Be Subject To Dot’s Final Approval  Music To Be Provided In The Following Instances: O Lunch Reception And Entry Into The Ballroom At The Start Of The Ceremony. O Background Lounge Music To Be Played Throughout The Ceremony When The Lunch Commences, Music Should Be Played In Between Transitions. O Dot To Approve The Choice Of Music To Play If Necessary.  Event Management Team Who Shall Coordinate, And Oversee The Light, Sound, Audio-visual, Scenery, Technical Requirements, Staging, Choreography, And Other Elements And Requirements Of The Overall Show. The Event Management Company Shall Source The Appropriate Artist, Technical Practitioners, Etc. Required To Implement The Overall Program Scenario For The Event Which Should Include But Not Be Limited To The Following: O Event Coordinator O Content Writer O Set And Stage Designer O Creative Artwork Specialist O Technical Director O Production Manager O Venue Stylist Note: Submit Together With The Technical Bid, The List And Portfolio Of Proposed Entertainment Acts, Mc/host.  Physical And Technical Requirements Overall Venue Decor/execution And Construction For The Abovementioned Event To Include But Not Limited To: A. Lunch Reception 1. Minimum Of Two (2) 6x42” Plasma Screens (landscape) On Stands Which Are Usb Compatible Or Laptops If No Usb Port Is Available. 2. Plasma Screens Will Show The Dot Videos On A Loop Throughout The Event. 3. Official Photo Walls And Media Booth Areas Are Often Placed In The Cocktail Area. 4. High Cocktail Tables With Decoration (1x Table To Be Used By Organization Staff For Registration And X Number Of Tables With Rise To Be Used For The Corporate Giveaways) 5. Red Carpet And Stanchions B. Stage Design 1. The Main Stage Must Be Large Enough To Accommodate Panoramic Led Walls (similar To Events By The Presidential Communications Office). 2. Must Also Allow A Maximum Number Of Tables In The Ballroom Or Area. 3. 3 Sets Of Stage Stairs; Large Middle Set Front Of The Stage, Backstage Left And Backstage Right. 4. Edges Or Stairs To Be Marked With Tape Or Similar For Health And Safety. 5. Stage Set-up, Subject To Adjustments Of Led Size, Depending On The Final Venue: Option 1 Stage Set-up: 3x Led Screens (one Center Stage And Two On Either Side). Screen Size Depends On Stage Design And The Size Of The Ballroom Or Event Area. All Screens Must Be Rigged And Framed By A Structure Surrounded By Neat Black Cloth Or Similar. Option 2 Stage Set-up: 1x Large Led Screen Which Can Be Divided Into Sub-screens. Stage Size Fit To Scale Of Ballroom Or Event Area. • • C. Printed Branding 1. Podium - To Be Supplied By Venue Or Av (1x Podium If 1 Mc). Preferably A Digital Podium For Us To Design A Cover Podium To Be Boxed In As Per Image [insert Photo]. The Podium Must Always Be Flat And/or Have A Lip To Avoid Folder Slipping. D. Photo Walls 2x Photo Walls Usually W 8m X H 24m, But Subject To Change Depending On The Size Of Space Available. Please Provide The Dimensions According To Location. Can Be Placed In Cocktail/ Pre-function Area, When Guests Arrive Or At The Adjacent Side In The Dining Area If Sufficient Space Or Immediately Outside The Event Area. Production Team To Build A Suitable Frame To Finish The Look. Both Walls Must Be Well Lit. E. 360 Photo And Video Booth Or To Be Set Up Near The Photo Walls Or At The Cocktail Area F. Invitational, Confirmation, Admin Work. Assist Opaa In The Conceptualization, - Management And Implementation Of All E-invites And Rsvp. - Drafting Of Invitation Content, Printing (including Onsite), Organization, Management And Execution Of Online Invitation And Related Communication (e-invitations, E-posters, Save The Date And On-the-day Poster, Confirmation, Certificate Of Attendance (if Required) Note: All Printed Materials Must Be Suitable For Photography, I.e Should Not Reflect Much Light As To Allow For Logos To Stand Out And Better Quality. These Also Need To Be Hung Against A Frame (ideally Plywood) So That The Print Can Be Fixed To A Rigid Board Surface So There Is No Creasing. We Advise All Printed Materials To Be Printed On Cloth Or Matt Lamination To Prevent Glare From Camera Flashes. The Graphics For All The Above Will Be Designed By The Opaa Team And Emailed To The Awarded Emc For Print And Installation. All Printed Branding Such As Photo Walls And Media Booths Are To Have Black Carpeted Platforms At Approximately 15cm In Height, Width To Be Approximately 1 Meter, And Length Dependent On Size. These Are To Be Built And Installed By The Production Team. G. Provide A Venue For Alignment Meeting And/or Technical Run With The Complete Technical And Physical Requirements Mentioned Herein. H. Ballroom Decoration: Decoration Of The Ballroom Is Required To Be A High Standard To Fit In With The Caliber Of Attendees. Display Of Local Culture And Colors Is Encouraged. Round Table Banqueting Tables And Chairs (8 Pax) With Tablecloths, Runners, And Chair Covers, Finished With A Decorative Floral Arrangement Or Centerpiece. Each Table To Be Displayed With Table Number Stand Supplied By The Venue And A Branded Menu For Each Guest (opaa Will Finalize Sign Prior To Printing).  Provide The Necessary Equipment And Technical Team, Requirements For The Event, And Coordinate With The Technical Team Of The Venue (tba) For The Setup And Installation Of All Physical And Technical Requirements, Including, But Not Limited To The Following: 1. Equipment - 1x Roaming Videographer For The Lunch Reception And Around The Main Room For The Tables. - 1x Vision Mixer/switcher And Operator. This Mixer Enables A Switch Between Several Different Sources And Mixes So We Can Switch Between The Live Feed, Powerpoint Slides, And Videos. Playback Pro Should Be Used When Video Cueing And Playing - 2x Pre-view Monitors And 2x Laptops In The Audio-visual Booth. It Is Preferred That Lighting, Sound, And Av Engineers Are Seated Next To Each Other In The Same Technical Box - 1x Professional Video Camera And Operator To Film The Entire Ceremony. Please Ensure That These Cameras Are Manually Operated And Not On An Automatic Focus. Cameras Are To Also Supply A Live Feed To The Above-mentioned Projections Screens. Footage Of The Event Is To Be Given To Us Immediately After The Ceremony On A Hard Drive Which The Emc Will Supply. -3x Professional Cameras, Operators, And Handheld Microphones For The Media Interview Enclosure Which Is Off Stage And Next To The Photo Wall. These Video Interviews Will Feature On Youtube, Therefore Need To Be In The Following Format .mov/.mp4/.avi With A Resolution And Aspect Ratio Of 720p: 1280x720 (preferred) Or 1080p: 1920x1080. All Footage Is To Be Saved Immediately After The Event And Copied Onto The Hard Drive Supplied By The Event Organizers. They Are Not Required To Edit These Videos; Opaa Will Do This. Electricity Is Needed In This Area. A Videography Brief Will Be Given To Assigned Videographers On Event Day By An Organizing Representative -1x Professional Digital Photographer Dedicated To The Photo Wall Photographs To Be Downloaded To The Organizer's Staff Laptop At The End Of The Night. A Photography Brief Will Be Given On Event Day By An Organizing Representative. - Provide All The Necessary Cabling For The Entire Production And For All Recording To Be In Hd. 2. Lighting And Sound A. Lunch Reception: Microphone And Stand For Speeches And/or Announcements (pa System); Relaxed/mood Lighting B. Pa System - 2x Gooseneck Microphones At Each Podium (reduce To One If Only One Host) - 2x Handheld Microphones In The Tech Box For Voice-over Introductions And As A Backup (reduce To One Host) - Generic/warm Theatrical Lighting To Give General Cover For The Stage And Band Areas - All Lighting/sound Requirements Of Band/performers As Per Their Technical Riders - Speakers Are To Be Flown/hung From Trusses To Allow For Overall Sound. Not On The Floor At The Front Of The Stage Or On Stands Around The Room. - Lighting In The Audio-visual Booth Area -uplighting For 2x Photo Walls - Lighting For The Backstage Area 3. The Winning Bidder Will Coordinate With Opaa For The Final Program Scenario And Script. 4. Vehicle Hire For Two (2) Mini Vans Or One (1) Super Grandia Van For One (1) Day Within Metro Manila For 12-hour Use That Will Transfer Opaa Secretariat And All Equipment; Should Be Inclusive Of Driver, Gas And Parking Fees And Driver Fees 5. Produce And Execute The Shooting And Pre-recordings Of The Messages Of Key Officials Or Other Speakers’ Messages Should The Need Arise 6. Document In Video And Photo Formats Of The Event For Submission To The Following: A. Opaa: Raw Footage Of The Event Saved In An External Hard Drive To Be Provided By The Emc; The Opaa Team Will Be The One To Edit B. Opaa: 1 Same-day Edit (sde) Video To Be Presented During The Dinner And 1 Video With Highlights Of The Event (2-3minute) For Social Media Posting And All Raw Footage Saved In An External Hard Drive To Be Provided By The Emc 7. Final Dry Run/technical Check Of The Program Scenario To Be Presented For Final Approval Of Tpb Before The Event 9. Submit The End Report, Recordings Of The Activities, Videos, And Final Cut (2-3 Minute Video Highlights) To Opaa After The Event 8. Opaa Shall Have Full Ownership Of All The Data Gathered And Presented (both In Hard And Softcopy Files) From The Event 9. All Records Are Regarded As Confidential And Therefore Will Not Be Divulged To Any Third Party Without Prior Written Approval Of Opaa. The Tpb Has The Right To Request Sight Of, And Copies Of All Records Kept, On The Provision That The Company Is Given Reasonable Notice Of Such A Request 10. Ensure The Privacy And Security Of All Confidential, Privileged Personal Information, And/or Sensitive Information In Accordance With Republic Act No. 10173, Otherwise Known As The Data Privacy Act Of 2021 And Its Implementing Rules And Regulations 11. The Winning Bidder Should: A. Secure All Necessary Permits For Any Song And/or Videos Owned By 3rd Party; B. Provide All Logistical Requirements Of The Entertainers And Their Production Team 12. Assistance On Other Related Matters That May Not Have Been Included In This Document But Deemed Necessary By Either Party. Viii. Eligibility Requirements For The Mice Organizer/event Management Service Provider  Must Be A Professional Full Service Mice Organizer/event Management Services Provider Specializing In Handling/producing/organizing/staging National Level Full-packaged Corporate Events, Corporate Communications, Creating And Staging Physical, As Well As Hybrid Content, Program And Broadcast;  Duly Registered Philippine-based Company With Appropriate Government Agency;  With Significant Experience Working With Government And Private Sector In Tourism, Utilizing State Of The Art Equipment To Produce Premium Physical, As Well As Hybrid Quality Content, Program And Broadcast;  Highly Experienced In Producing Contents And Programs That Are Dynamic, Filipino-themed But Global Standard;  Highly Knowledgeable In Government Procurement Process And Procedure;  Must Be A Dot-accredited Mice Organizer, And Must Engage With Dot-accredited Supplier/s;  Must Be Accredited With The Philippine Government Electronic Procurement Systems (philgeps);  Must Provide A Breakdown Of Prices And Services Included In The Quotation Complete With E-vat And Other Government Taxes;  Amenable To Government Procedure Or Send-bill Arrangement And Preferably With Land Bank Of The Philippines Account;  With Lgu-registered Physical Office In Metro Manila. Ix. Legal/technical Requirements 1. Valid Mayor’s/business Permit 2. Philgeps Registration Number 3. Latest Income/business Tax Return 4. Original Or Certified True Copy Of Duly Notarized Omnibus Sworn Statement X. Payment Procedure Government Procedure And Subject To Appropriate Government Taxes Xi. Approved Budget For The Contract (abc): The Approved Budget For The Contract (abc) Is Four Hundred Twenty-two Thousand Pesos And Nine Hundred Eighty Four 03/100 Pesos Only (php422,984.03) Inclusive Of All Applicable Taxes And Fees. Xii. Submission Of Proposal 4f | Procurement Management Division Department Of Tourism Bldg., 351 Sen. Gil Puyat Avenue, Makati Cit For Inquiries: Approved By: Contact: Mr. Dee A. Mandigma Atty. Glenn Albert Ocampo +9664758757 Oic – Director, Opaa Damandigma@tourism.gov.ph, 3f | Office Of Public Affairs And Advocacy (opaa) Telephone Numbers: 8459-5200 Local 306

Austria-feldkirch: Construction Work For Buildings Relating To Health

Details: Item Unique Identification And Valuation (jan 2023)|19|||||||||||||||||||| inspection Of Supplies--fixed-price (aug 1996)|2||| time Of Delivery (june 1997)|20||||||||||||||||||||| stop-work Order (aug 1989)|1|| general Information-fob-destination|1|b| wide Area Workflow Payment Instructions (jan 2023)|16|combo||tbd|n00104|tbd|tbd|tbd|tbd|tbd|tbd|tbd|||||| navy Use Of Abilityone Support Contractor - Release Of Offeror Information (3-18))|1|wss| value Engineering (jun 2020)|3|||| equal Opportunity (sep 2016)|2||| small Business Subcontracting Plan (dod Contracts)- Basic (dec 2019)|2||| integrity Of Unit Prices (nov 2021)|1|| equal Opportunity For Veterans (jun 2020)|4||||| small Business Subcontracting Plan (sep 2023)|4||||| equal Opportunity For Workers With Disabilities (jun 2020)|2||| transportation Of Supplies By Sea (jan 2023)|2||| contractor Purchasing System Administration-basic (may 2014)|1|| authorized Deviations In Clauses (nov 2020)|2|federal Acquisition Regulation |chapter 1| requirements For Certified Cost Or Pricing Data And Data Other Than Certified Cost Or Pricing Data-modifications (nov 2021))|7|||||||| list Of Award Attachments|5|||||| alternate A, Annual Representations And Certifications (nov 2023)|13|||||||||||||| small Business Program Representations (feb 2024)|4||||| royalty Information (apr 1984)|1|| certification Regarding Knowledge Of Child Labor For Listed End Products(feb 2021))|4||||| annual Representations And Certifications (may 2024)|13|334412|750 Employees|||||||||||| requirements For Submission Of Proposals Via Electronic Media (jan 2018)|1|email Only| requirements For Certified Cost Or Pricing Data And Data Other Than Certified Cost Or Pricing Data (nov 2021))|7|||||||| type Of Contract (apr 1984)|1|ffp| alterations In Solicitation (apr 1984)|3|||| notice Of Priority Rating For National Defense, Emergency Perpardeness, And Enrgy Progam Use (april 2008))|2||x| requirements For Certified Cost Or Pricing Data And Data Other Than Certifiedcost Or Pricing Data (may 2024))|1|| the Reason For This Amendment Is The Add The Below Terms To This Solicitation / Resultant Contract: 1: The Government's Required Delivery Date (rdd) Is 31 December 2026 Or Earlier On All Deliveries. 2: The Following Term Applies To This Solicitation And Resultant Contract/order: "this Order �solicitation� Is Issued Under And Pursuant To The Provisions Of The Basic Ordering Agreement (boa). The Terms And Conditions Of The Boa Are Hereby Incorporated By Reference And, Except As Provided Herein By This Order �solicitation�, Remain In Full force And Effect. If Any Conflict Arises In The Terms Of This Order Versus The Terms In The Boa, The Terms Of The Boa Shall Apply." \ 1. Scope 1.1 This Contract/purchase Order Contains The Requirements For Manufacture And The Contract Quality Requirements For The Heater Assembly,rad . 2. Applicable Documents 2.1 Applicable Documents - The Document(s) Listed Below Form A Part Of This Contract/purchase Order Including Modifications Or Exclusions. 2.1.1 "document References" Listed Below Must Be Obtained By The Contractor. Ordering Information Is Included As An Attachment To This Contract/purchase Order. 3. Requirements 3.1 Cage Code/reference Number Items - The Heater Assembly,rad Furnished Under This contract/purchase Order Shall Be The Design Represented By Cage Code(s) reference Number(s). Cage _______ Ref. No. ;53711 5188230; 3.2 Marking - This Item Shall Be Physically Identified In Accordance with ;mil-std-130, Rev N, 16 Nov 2012; . 3.3 Changes In Design, Material Servicing, Or Part Number - Except For A Code 1 Change, Which Shall Be Processed As Provided In The Code Statement Shown Below, No Substitution Of Items Shall Be Made Until The Navicp-mech Contracting Officer Has Notified And approval Has Been Given By Issuance Of A Written Change Order. When Any Change In Design, Material, Servicing Or Part Number Is Made To Replace Or Substitute Any Item To Be Furnished On This Contract/purchase Order, The Contractor Shall Furnish, For The substituting/replacement Item, A Drawing And An Explanation Of The Reason For The Change, Explaining The Reason Therefor. If Finished Detail Drawings Are Not Available, Shop Drawings In The Form Used By The Manufacturer Will Be Acceptable For Government evaluation. When Notifying The Procurement Contracting Officer Of The Reasons For Making Substitutions, The Type Of Change Shall Be Indicated By Code Number In Accordance With One Of The Following Statements: code 1: Part Number Change Only - If The Manufacturer's Part Number Indicated Thereon Has Changed, But The Parts Are Identical In All Respects, Supply The Item And Advise Navicp-mech Immediately Of The New Part Number. code 2: Assembly (or Set Or Kit) Not Furnished - Used Following Detail Parts. code 3: Part Not Furnished Separately - Use Assembly. code 4: Part Redesigned - Old And New Parts Are Completely Interchangeable. code 5: Part Redesigned - New Part Replaces Old. Old Part Cannot Replace New. code 6: Part Redesigned - Parts Not Interchangeable. 3.4 Soldering - The Requirements For Soldered Electrical And Electronic Assemblies Shall Conform To Ipc J-std-001, Class ;3; . 4. Quality Assurance 4.1 Responsibility For Inspection - Unless Otherwise Specified In The Contract/purchase Order, The Contractor Is Responsible For The Performance Of All Inspection Requirements As Specified Herein. Except As Otherwise Specified In The Contract/purchase Order, the Contractor May Use His Own Or Any Other Facilities Suitable For The Performance Of The Inspection Requirements Specified Herein, Unless Disapproved By The Government. The Government Reserves The Right To Perform Any Of The Inspections Set Forth In The specification Where Such Inspections Are Deemed Necessary To Assure Supplies And Services Conform To Prescribed Requirements. 4.2 Responsibility For Compliance - All Items Must Meet All Requirements Of This Contract/purchase Order. The Inspection Set Forth In This Specification Shall Become A Part Of The Contractor's Overall Inspection System Or Quality Program. The Absence Of Any inspection Requirements Shall Not Relieve The Contractor Of The Responsibility Of Assuring That All Products Or Supplies Submitted To The Government For Acceptance Comply With All Requirements Of The Contract/purchase Order. Sampling In Quality Conformance does Not Authorize Submission Of Known Defective Material, Either Indicated Or Actual, Not Does It Commit The Government To Acceptance Of Defective Material. 4.3 Records - Records Of All Inspection Work By The Contractor Shall Be Kept Complete And Available To The Government During The Performance Of Contract/purchase Order And For A Period Of 365 Calendar Days After Final Delivery Of Supplies. 5. Packaging 5.1 Preservation, Packaging, Packing And Marking - Preservation, Packaging, Packing And Marking Shall Be In Accordance With The Contract/purchase Order Schedule And As Specified Below. mil-std 2073 Packaging Applies As Found Elsewhere In The Schedule 6. Notes 6.1 Ordering Information For Document References - The Department Of Defense Single Stock Point (dodssp), Website Http://www.dsp.dla.mil/, Provides Product Information For The Department Of Defense Index Of Specifications And Standards (dodiss) (i.e.military/federal Specifications And Standards), Data Item Descriptions (dids), And Other Dodssp Products. Most Specifications Can Obtained Directly From Http://quicksearch.dla.mil/ a. Availability Of Cancelled Documents - The Dodssp Offers Cancelled Documentsthat Are Required By Private Industry In Fulfillment Of Contractual Obligationsin Paper Format. Documents Can Be Requested By Phoning The Subscription Services Desk. b. Commercial Specifications, Standards, And Descriptions - These Specifications, Standards And Descriptions Are Not Available From Government Sources. Theymay Be Obtained From The Publishers Of The Applicable Societies. c. Ordnance Standards (os), Weapons Specifications (ws), And Navord Ostd 600 Pages - These Type Publications May Be Obtained By Submitting A Request To: commander, Indian Head Division, Naval Surface Warfare Center code 8410p, 101 Strauss Avenue indian Head, Md 20640-5035 d. On Post-award Actions, Requests For "official Use Only" And "noforn" (not Releasable To Foreign Nationals) Documents Must Identify The Government Contractnumber, And Must Be Submitted Via The Cognizant Defense Contract Management Command (dcmc) For certification Of Need For The Document. On Pre-award Actions Such Requests Must Be Submitted To The Pco For Certification Of Need For The Document. e. Noforn Military Specifications And Standards (including Amendments, Change Notices And Supplements, But Not Interim Changes) To Be Ordered From: contracting Officer navsup-wss code 87321 5450 Carlisle Pike p.o. Box 2020 mechanicsburg, Pa. 17055-0788 f. Nuclear Reactor Publications Assigned Navsea Documents And Identification Numbers (i.e. Navsea Welding Standard, Navsea 250-1500-1) Are To Be Ordered Enue: commanding Officer navsup-wss code 009 5450 Carlisle Pike p.o. Box 2020 mechanicsburg, Pa. 17055-0788 g. Technical Manuals Assigned Navsea Identification Numbers (i.e. Navsea Welding And Brazing Procedure, Navsea S9074-aq-gib-010/248) Are To Be Ordered From: commanding Officer navsup-wss code 1 Support Branch 700 Robbins Avenue philadelphia, Pa. 19111-5094 h. Interim Changes And Classified Specifications Must Be Obtained By Submitting A Request On Dd Form 1425 To Navsup-wss. 6.2 Notice To Distributors/offerors - Consideration For Award Of Contract Shall Be Given Only To Authorized Distributors Of The Original Manufacturer's Item Represented In This Solicitation. If You Desire To Be Considered As A Potential Source For Award Of this Contract, Proof Of Being An Authorized Distributor Shall Be Provided On Company Letterhead Signed By A Responsible Company Official And Sent With Your Offer To The Procurement Contracting Officer. 6.3 In Accordance With Opnavinst 5510.1 All Documents And Drawings Provided By The U.s. Navy To Perspective Contractors Must Include A "distribution Statement" To Inform The Contractor Of The Limits Of Distribution, And The Safeguarding Of The Information contained On Those Documents And Drawings. There Are 7 (seven) Seperate Distribution Statement Codes Used For Non-classified Documents And Drawings. The Definition For Each Is As Follows: a... Approved For Public Release; Distribution Is Unlimited. b... Distribution Authorized To Us Governments Agencies Only. c... Distribution Authorized To Us Government Agencies And Their Contractors. d... Distribution Authorized To Dod And Dod Contractors Only. e... Distribution Authorized To Dod Components Only. f... Further Distribution Only As Directed By Commander, Naval Sea Systems Command, Code 09t. x... Distribution Is Authorized To Us Government Agencies And Private Individuals Or Enterprises Eligible To Obtain Export Controlled Technical Data In Accordance With Opnavinst 5510.161. 1. Scope 1.1 This Contract/purchase Order Contains The Requirements For Manufacture And The Contract Quality Requirements For The Modulator . 2. Applicable Documents 2.1 Applicable Documents - The Document(s) Listed Below Form A Part Of This Contract/purchase Order Including Modifications Or Exclusions. 2.1.1 "document References" Listed Below Must Be Obtained By The Contractor. Ordering Information Is Included As An Attachment To This Contract/purchase Order. 3. Requirements 3.1 Cage Code/reference Number Items - The Modulator Furnished Under This contract/purchase Order Shall Be The Design Represented By Cage Code(s) reference Number(s). Cage _______ Ref. No. ;53711 5336325; 3.2 Marking - This Item Shall Be Physically Identified In Accordance with ;mil-std-130, Rev N, 16 Nov 2012; . 3.3 Changes In Design, Material Servicing, Or Part Number - Except For A Code 1 Change, Which Shall Be Processed As Provided In The Code Statement Shown Below, No Substitution Of Items Shall Be Made Until The Navicp-mech Contracting Officer Has Notified And approval Has Been Given By Issuance Of A Written Change Order. When Any Change In Design, Material, Servicing Or Part Number Is Made To Replace Or Substitute Any Item To Be Furnished On This Contract/purchase Order, The Contractor Shall Furnish, For The substituting/replacement Item, A Drawing And An Explanation Of The Reason For The Change, Explaining The Reason Therefor. If Finished Detail Drawings Are Not Available, Shop Drawings In The Form Used By The Manufacturer Will Be Acceptable For Government evaluation. When Notifying The Procurement Contracting Officer Of The Reasons For Making Substitutions, The Type Of Change Shall Be Indicated By Code Number In Accordance With One Of The Following Statements: code 1: Part Number Change Only - If The Manufacturer's Part Number Indicated Thereon Has Changed, But The Parts Are Identical In All Respects, Supply The Item And Advise Navicp-mech Immediately Of The New Part Number. code 2: Assembly (or Set Or Kit) Not Furnished - Used Following Detail Parts. code 3: Part Not Furnished Separately - Use Assembly. code 4: Part Redesigned - Old And New Parts Are Completely Interchangeable. code 5: Part Redesigned - New Part Replaces Old. Old Part Cannot Replace New. code 6: Part Redesigned - Parts Not Interchangeable. 4. Quality Assurance 4.1 Responsibility For Inspection - Unless Otherwise Specified In The Contract/purchase Order, The Contractor Is Responsible For The Performance Of All Inspection Requirements As Specified Herein. Except As Otherwise Specified In The Contract/purchase Order, the Contractor May Use His Own Or Any Other Facilities Suitable For The Performance Of The Inspection Requirements Specified Herein, Unless Disapproved By The Government. The Government Reserves The Right To Perform Any Of The Inspections Set Forth In The specification Where Such Inspections Are Deemed Necessary To Assure Supplies And Services Conform To Prescribed Requirements. 4.2 Responsibility For Compliance - All Items Must Meet All Requirements Of This Contract/purchase Order. The Inspection Set Forth In This Specification Shall Become A Part Of The Contractor's Overall Inspection System Or Quality Program. The Absence Of Any inspection Requirements Shall Not Relieve The Contractor Of The Responsibility Of Assuring That All Products Or Supplies Submitted To The Government For Acceptance Comply With All Requirements Of The Contract/purchase Order. Sampling In Quality Conformance does Not Authorize Submission Of Known Defective Material, Either Indicated Or Actual, Not Does It Commit The Government To Acceptance Of Defective Material. 4.3 Records - Records Of All Inspection Work By The Contractor Shall Be Kept Complete And Available To The Government During The Performance Of Contract/purchase Order And For A Period Of 365 Calendar Days After Final Delivery Of Supplies. 5. Packaging 5.1 Preservation, Packaging, Packing And Marking - Preservation, Packaging, Packing And Marking Shall Be In Accordance With The Contract/purchase Order Schedule And As Specified Below. mil-std 2073 Packaging Applies As Found Elsewhere In The Schedule 6. Notes 6.1 Ordering Information For Document References - The Department Of Defense Single Stock Point (dodssp), Website Http://www.dsp.dla.mil/, Provides Product Information For The Department Of Defense Index Of Specifications And Standards (dodiss) (i.e.military/federal Specifications And Standards), Data Item Descriptions (dids), And Other Dodssp Products. Most Specifications Can Obtained Directly From Http://quicksearch.dla.mil/ a. Availability Of Cancelled Documents - The Dodssp Offers Cancelled Documentsthat Are Required By Private Industry In Fulfillment Of Contractual Obligationsin Paper Format. Documents Can Be Requested By Phoning The Subscription Services Desk. b. Commercial Specifications, Standards, And Descriptions - These Specifications, Standards And Descriptions Are Not Available From Government Sources. Theymay Be Obtained From The Publishers Of The Applicable Societies. c. Ordnance Standards (os), Weapons Specifications (ws), And Navord Ostd 600 Pages - These Type Publications May Be Obtained By Submitting A Request To: commander, Indian Head Division, Naval Surface Warfare Center code 8410p, 101 Strauss Avenue indian Head, Md 20640-5035 d. On Post-award Actions, Requests For "official Use Only" And "noforn" (not Releasable To Foreign Nationals) Documents Must Identify The Government Contractnumber, And Must Be Submitted Via The Cognizant Defense Contract Management Command (dcmc) For certification Of Need For The Document. On Pre-award Actions Such Requests Must Be Submitted To The Pco For Certification Of Need For The Document. e. Noforn Military Specifications And Standards (including Amendments, Change Notices And Supplements, But Not Interim Changes) To Be Ordered From: contracting Officer navsup-wss code 87321 5450 Carlisle Pike p.o. Box 2020 mechanicsburg, Pa. 17055-0788 f. Nuclear Reactor Publications Assigned Navsea Documents And Identification Numbers (i.e. Navsea Welding Standard, Navsea 250-1500-1) Are To Be Ordered Enue: commanding Officer navsup-wss code 009 5450 Carlisle Pike p.o. Box 2020 mechanicsburg, Pa. 17055-0788 g. Technical Manuals Assigned Navsea Identification Numbers (i.e. Navsea Welding And Brazing Procedure, Navsea S9074-aq-gib-010/248) Are To Be Ordered From: commanding Officer navsup-wss code 1 Support Branch 700 Robbins Avenue philadelphia, Pa. 19111-5094 h. Interim Changes And Classified Specifications Must Be Obtained By Submitting A Request On Dd Form 1425 To Navsup-wss. 6.2 Notice To Distributors/offerors - Consideration For Award Of Contract Shall Be Given Only To Authorized Distributors Of The Original Manufacturer's Item Represented In This Solicitation. If You Desire To Be Considered As A Potential Source For Award Of this Contract, Proof Of Being An Authorized Distributor Shall Be Provided On Company Letterhead Signed By A Responsible Company Official And Sent With Your Offer To The Procurement Contracting Officer. 6.3 In Accordance With Opnavinst 5510.1 All Documents And Drawings Provided By The U.s. Navy To Perspective Contractors Must Include A "distribution Statement" To Inform The Contractor Of The Limits Of Distribution, And The Safeguarding Of The Information contained On Those Documents And Drawings. There Are 7 (seven) Seperate Distribution Statement Codes Used For Non-classified Documents And Drawings. The Definition For Each Is As Follows: a... Approved For Public Release; Distribution Is Unlimited. b... Distribution Authorized To Us Governments Agencies Only. c... Distribution Authorized To Us Government Agencies And Their Contractors. d... Distribution Authorized To Dod And Dod Contractors Only. e... Distribution Authorized To Dod Components Only. f... Further Distribution Only As Directed By Commander, Naval Sea Systems Command, Code 09t. x... Distribution Is Authorized To Us Government Agencies And Private Individuals Or Enterprises Eligible To Obtain Export Controlled Technical Data In Accordance With Opnavinst 5510.161. 1. Scope 1.1 This Contract/purchase Order Contains The Requirements For Manufacture And The Contract Quality Requirements For The Circuit Card Assemb . 2. Applicable Documents 2.1 Applicable Documents - The Document(s) Listed Below Form A Part Of This Contract/purchase Order Including Modifications Or Exclusions. 2.1.1 "document References" Listed Below Must Be Obtained By The Contractor. Ordering Information Is Included As An Attachment To This Contract/purchase Order. 3. Requirements 3.1 Cage Code/reference Number Items - The Circuit Card Assemb Furnished Under This contract/purchase Order Shall Be The Design Represented By Cage Code(s) reference Number(s). Cage _______ Ref. No. ;53711 6166870; 3.2 Marking - This Item Shall Be Physically Identified In Accordance with ;mil-std-130, Rev N, 16 Nov 2012; . 3.3 Changes In Design, Material Servicing, Or Part Number - Except For A Code 1 Change, Which Shall Be Processed As Provided In The Code Statement Shown Below, No Substitution Of Items Shall Be Made Until The Navicp-mech Contracting Officer Has Notified And approval Has Been Given By Issuance Of A Written Change Order. When Any Change In Design, Material, Servicing Or Part Number Is Made To Replace Or Substitute Any Item To Be Furnished On This Contract/purchase Order, The Contractor Shall Furnish, For The substituting/replacement Item, A Drawing And An Explanation Of The Reason For The Change, Explaining The Reason Therefor. If Finished Detail Drawings Are Not Available, Shop Drawings In The Form Used By The Manufacturer Will Be Acceptable For Government evaluation. When Notifying The Procurement Contracting Officer Of The Reasons For Making Substitutions, The Type Of Change Shall Be Indicated By Code Number In Accordance With One Of The Following Statements: code 1: Part Number Change Only - If The Manufacturer's Part Number Indicated Thereon Has Changed, But The Parts Are Identical In All Respects, Supply The Item And Advise Navicp-mech Immediately Of The New Part Number. code 2: Assembly (or Set Or Kit) Not Furnished - Used Following Detail Parts. code 3: Part Not Furnished Separately - Use Assembly. code 4: Part Redesigned - Old And New Parts Are Completely Interchangeable. code 5: Part Redesigned - New Part Replaces Old. Old Part Cannot Replace New. code 6: Part Redesigned - Parts Not Interchangeable. 3.4 Electrostatic Discharge Control - The Contractor Shall Comply With The Electrostatic Discharge Control Requirements Established In Mil-std-1686. 3.5 Soldering - The Requirements For Soldered Electrical And Electronic Assemblies Shall Conform To Ipc J-std-001, Class ;3; . 4. Quality Assurance 4.1 Responsibility For Inspection - Unless Otherwise Specified In The Contract/purchase Order, The Contractor Is Responsible For The Performance Of All Inspection Requirements As Specified Herein. Except As Otherwise Specified In The Contract/purchase Order, the Contractor May Use His Own Or Any Other Facilities Suitable For The Performance Of The Inspection Requirements Specified Herein, Unless Disapproved By The Government. The Government Reserves The Right To Perform Any Of The Inspections Set Forth In The specification Where Such Inspections Are Deemed Necessary To Assure Supplies And Services Conform To Prescribed Requirements. 4.2 Responsibility For Compliance - All Items Must Meet All Requirements Of This Contract/purchase Order. The Inspection Set Forth In This Specification Shall Become A Part Of The Contractor's Overall Inspection System Or Quality Program. The Absence Of Any inspection Requirements Shall Not Relieve The Contractor Of The Responsibility Of Assuring That All Products Or Supplies Submitted To The Government For Acceptance Comply With All Requirements Of The Contract/purchase Order. Sampling In Quality Conformance does Not Authorize Submission Of Known Defective Material, Either Indicated Or Actual, Not Does It Commit The Government To Acceptance Of Defective Material. 4.3 Records - Records Of All Inspection Work By The Contractor Shall Be Kept Complete And Available To The Government During The Performance Of Contract/purchase Order And For A Period Of 365 Calendar Days After Final Delivery Of Supplies. 5. Packaging 5.1 Preservation, Packaging, Packing And Marking - Preservation, Packaging, Packing And Marking Shall Be In Accordance With The Contract/purchase Order Schedule And As Specified Below. mil-std 2073 Packaging Applies As Found Elsewhere In The Schedule 6. Notes 6.1 Ordering Information For Document References - The Department Of Defense Single Stock Point (dodssp), Website Http://www.dsp.dla.mil/, Provides Product Information For The Department Of Defense Index Of Specifications And Standards (dodiss) (i.e.military/federal Specifications And Standards), Data Item Descriptions (dids), And Other Dodssp Products. Most Specifications Can Obtained Directly From Http://quicksearch.dla.mil/ a. Availability Of Cancelled Documents - The Dodssp Offers Cancelled Documentsthat Are Required By Private Industry In Fulfillment Of Contractual Obligationsin Paper Format. Documents Can Be Requested By Phoning The Subscription Services Desk. b. Commercial Specifications, Standards, And Descriptions - These Specifications, Standards And Descriptions Are Not Available From Government Sources. Theymay Be Obtained From The Publishers Of The Applicable Societies. c. Ordnance Standards (os), Weapons Specifications (ws), And Navord Ostd 600 Pages - These Type Publications May Be Obtained By Submitting A Request To: commander, Indian Head Division, Naval Surface Warfare Center code 8410p, 101 Strauss Avenue indian Head, Md 20640-5035 d. On Post-award Actions, Requests For "official Use Only" And "noforn" (not Releasable To Foreign Nationals) Documents Must Identify The Government Contractnumber, And Must Be Submitted Via The Cognizant Defense Contract Management Command (dcmc) For certification Of Need For The Document. On Pre-award Actions Such Requests Must Be Submitted To The Pco For Certification Of Need For The Document. e. Noforn Military Specifications And Standards (including Amendments, Change Notices And Supplements, But Not Interim Changes) To Be Ordered From: contracting Officer navsup-wss code 87321 5450 Carlisle Pike p.o. Box 2020 mechanicsburg, Pa. 17055-0788 f. Nuclear Reactor Publications Assigned Navsea Documents And Identification Numbers (i.e. Navsea Welding Standard, Navsea 250-1500-1) Are To Be Ordered Enue: commanding Officer navsup-wss code 009 5450 Carlisle Pike p.o. Box 2020 mechanicsburg, Pa. 17055-0788 g. Technical Manuals Assigned Navsea Identification Numbers (i.e. Navsea Welding And Brazing Procedure, Navsea S9074-aq-gib-010/248) Are To Be Ordered From: commanding Officer navsup-wss code 1 Support Branch 700 Robbins Avenue philadelphia, Pa. 19111-5094 h. Interim Changes And Classified Specifications Must Be Obtained By Submitting A Request On Dd Form 1425 To Navsup-wss. 6.2 Notice To Distributors/offerors - Consideration For Award Of Contract Shall Be Given Only To Authorized Distributors Of The Original Manufacturer's Item Represented In This Solicitation. If You Desire To Be Considered As A Potential Source For Award Of this Contract, Proof Of Being An Authorized Distributor Shall Be Provided On Company Letterhead Signed By A Responsible Company Official And Sent With Your Offer To The Procurement Contracting Officer. 6.3 In Accordance With Opnavinst 5510.1 All Documents And Drawings Provided By The U.s. Navy To Perspective Contractors Must Include A "distribution Statement" To Inform The Contractor Of The Limits Of Distribution, And The Safeguarding Of The Information contained On Those Documents And Drawings. There Are 7 (seven) Seperate Distribution Statement Codes Used For Non-classified Documents And Drawings. The Definition For Each Is As Follows: a... Approved For Public Release; Distribution Is Unlimited. b... Distribution Authorized To Us Governments Agencies Only. c... Distribution Authorized To Us Government Agencies And Their Contractors. d... Distribution Authorized To Dod And Dod Contractors Only. e... Distribution Authorized To Dod Components Only. f... Further Distribution Only As Directed By Commander, Naval Sea Systems Command, Code 09t. x... Distribution Is Authorized To Us Government Agencies And Private Individuals Or Enterprises Eligible To Obtain Export Controlled Technical Data In Accordance With Opnavinst 5510.161. 1. Scope 1.1 This Contract/purchase Order Contains The Requirements For Manufacture And The Contract Quality Requirements For The Circuit Card Assemb . 2. Applicable Documents 2.1 Applicable Documents - The Document(s) Listed Below Form A Part Of This Contract/purchase Order Including Modifications Or Exclusions. 2.1.1 "document References" Listed Below Must Be Obtained By The Contractor. Ordering Information Is Included As An Attachment To This Contract/purchase Order. 3. Requirements 3.1 Cage Code/reference Number Items - The Circuit Card Assemb Furnished Under This contract/purchase Order Shall Be The Design Represented By Cage Code(s) reference Number(s). Cage _______ Ref. No. ;53711 5543728; 3.2 Marking - This Item Shall Be Physically Identified In Accordance with ;mil-std-130, Rev N, 16 Nov 2012; . 3.3 Changes In Design, Material Servicing, Or Part Number - Except For A Code 1 Change, Which Shall Be Processed As Provided In The Code Statement Shown Below, No Substitution Of Items Shall Be Made Until The Navicp-mech Contracting Officer Has Notified And approval Has Been Given By Issuance Of A Written Change Order. When Any Change In Design, Material, Servicing Or Part Number Is Made To Replace Or Substitute Any Item To Be Furnished On This Contract/purchase Order, The Contractor Shall Furnish, For The substituting/replacement Item, A Drawing And An Explanation Of The Reason For The Change, Explaining The Reason Therefor. If Finished Detail Drawings Are Not Available, Shop Drawings In The Form Used By The Manufacturer Will Be Acceptable For Government evaluation. When Notifying The Procurement Contracting Officer Of The Reasons For Making Substitutions, The Type Of Change Shall Be Indicated By Code Number In Accordance With One Of The Following Statements: code 1: Part Number Change Only - If The Manufacturer's Part Number Indicated Thereon Has Changed, But The Parts Are Identical In All Respects, Supply The Item And Advise Navicp-mech Immediately Of The New Part Number. code 2: Assembly (or Set Or Kit) Not Furnished - Used Following Detail Parts. code 3: Part Not Furnished Separately - Use Assembly. code 4: Part Redesigned - Old And New Parts Are Completely Interchangeable. code 5: Part Redesigned - New Part Replaces Old. Old Part Cannot Replace New. code 6: Part Redesigned - Parts Not Interchangeable. 4. Quality Assurance 4.1 Responsibility For Inspection - Unless Otherwise Specified In The Contract/purchase Order, The Contractor Is Responsible For The Performance Of All Inspection Requirements As Specified Herein. Except As Otherwise Specified In The Contract/purchase Order, the Contractor May Use His Own Or Any Other Facilities Suitable For The Performance Of The Inspection Requirements Specified Herein, Unless Disapproved By The Government. The Government Reserves The Right To Perform Any Of The Inspections Set Forth In The specification Where Such Inspections Are Deemed Necessary To Assure Supplies And Services Conform To Prescribed Requirements. 4.2 Responsibility For Compliance - All Items Must Meet All Requirements Of This Contract/purchase Order. The Inspection Set Forth In This Specification Shall Become A Part Of The Contractor's Overall Inspection System Or Quality Program. The Absence Of Any inspection Requirements Shall Not Relieve The Contractor Of The Responsibility Of Assuring That All Products Or Supplies Submitted To The Government For Acceptance Comply With All Requirements Of The Contract/purchase Order. Sampling In Quality Conformance does Not Authorize Submission Of Known Defective Material, Either Indicated Or Actual, Not Does It Commit The Government To Acceptance Of Defective Material. 4.3 Records - Records Of All Inspection Work By The Contractor Shall Be Kept Complete And Available To The Government During The Performance Of Contract/purchase Order And For A Period Of 365 Calendar Days After Final Delivery Of Supplies. 5. Packaging 5.1 Preservation, Packaging, Packing And Marking - Preservation, Packaging, Packing And Marking Shall Be In Accordance With The Contract/purchase Order Schedule And As Specified Below. mil-std 2073 Packaging Applies As Found Elsewhere In The Schedule 6. Notes 6.1 Ordering Information For Document References - The Department Of Defense Single Stock Point (dodssp), Website Http://www.dsp.dla.mil/, Provides Product Information For The Department Of Defense Index Of Specifications And Standards (dodiss) (i.e.military/federal Specifications And Standards), Data Item Descriptions (dids), And Other Dodssp Products. Most Specifications Can Obtained Directly From Http://quicksearch.dla.mil/ a. Availability Of Cancelled Documents - The Dodssp Offers Cancelled Documentsthat Are Required By Private Industry In Fulfillment Of Contractual Obligationsin Paper Format. Documents Can Be Requested By Phoning The Subscription Services Desk. b. Commercial Specifications, Standards, And Descriptions - These Specifications, Standards And Descriptions Are Not Available From Government Sources. Theymay Be Obtained From The Publishers Of The Applicable Societies. c. Ordnance Standards (os), Weapons Specifications (ws), And Navord Ostd 600 Pages - These Type Publications May Be Obtained By Submitting A Request To: commander, Indian Head Division, Naval Surface Warfare Center code 8410p, 101 Strauss Avenue indian Head, Md 20640-5035 d. On Post-award Actions, Requests For "official Use Only" And "noforn" (not Releasable To Foreign Nationals) Documents Must Identify The Government Contractnumber, And Must Be Submitted Via The Cognizant Defense Contract Management Command (dcmc) For certification Of Need For The Document. On Pre-award Actions Such Requests Must Be Submitted To The Pco For Certification Of Need For The Document. e. Noforn Military Specifications And Standards (including Amendments, Change Notices And Supplements, But Not Interim Changes) To Be Ordered From: contracting Officer navsup-wss code 87321 5450 Carlisle Pike p.o. Box 2020 mechanicsburg, Pa. 17055-0788 f. Nuclear Reactor Publications Assigned Navsea Documents And Identification Numbers (i.e. Navsea Welding Standard, Navsea 250-1500-1) Are To Be Ordered Enue: commanding Officer navsup-wss code 009 5450 Carlisle Pike p.o. Box 2020 mechanicsburg, Pa. 17055-0788 g. Technical Manuals Assigned Navsea Identification Numbers (i.e. Navsea Welding And Brazing Procedure, Navsea S9074-aq-gib-010/248) Are To Be Ordered From: commanding Officer navsup-wss code 1 Support Branch 700 Robbins Avenue philadelphia, Pa. 19111-5094 h. Interim Changes And Classified Specifications Must Be Obtained By Submitting A Request On Dd Form 1425 To Navsup-wss. 6.2 In Accordance With Opnavinst 5510.1 All Documents And Drawings Provided By The U.s. Navy To Perspective Contractors Must Include A "distribution Statement" To Inform The Contractor Of The Limits Of Distribution, And The Safeguarding Of The Information contained On Those Documents And Drawings. There Are 7 (seven) Seperate Distribution Statement Codes Used For Non-classified Documents And Drawings. The Definition For Each Is As Follows: a... Approved For Public Release; Distribution Is Unlimited. b... Distribution Authorized To Us Governments Agencies Only. c... Distribution Authorized To Us Government Agencies And Their Contractors. d... Distribution Authorized To Dod And Dod Contractors Only. e... Distribution Authorized To Dod Components Only. f... Further Distribution Only As Directed By Commander, Naval Sea Systems Command, Code 09t. x... Distribution Is Authorized To Us Government Agencies And Private Individuals Or Enterprises Eligible To Obtain Export Controlled Technical Data In Accordance With Opnavinst 5510.161. 6.3 Notice To Distributors/offerors - Consideration For Award Of Contract Shall Be Given Only To Authorized Distributors Of The Original Manufacturer's Item Represented In This Solicitation. If You Desire To Be Considered As A Potential Source For Award Of this Contract, Proof Of Being An Authorized Distributor Shall Be Provided On Company Letterhead Signed By A Responsible Company Official And Sent With Your Offer To The Procurement Contracting Officer. 1. Scope 1.1 This Contract/purchase Order Contains The Requirements For Manufacture And The Contract Quality Requirements For The Supply,electric . 2. Applicable Documents 2.1 Applicable Documents - The Document(s) Listed Below Form A Part Of This Contract/purchase Order Including Modifications Or Exclusions. 2.1.1 "document References" Listed Below Must Be Obtained By The Contractor. Ordering Information Is Included As An Attachment To This Contract/purchase Order. 3. Requirements 3.1 Cage Code/reference Number Items - The Supply,electric Furnished Under This contract/purchase Order Shall Be The Design Represented By Cage Code(s) reference Number(s). Cage _______ Ref. No. ;15090 6309885; 3.2 Marking - This Item Shall Be Physically Identified In Accordance with ;mil-std-130, Rev N, 16 Nov 2012; . 3.3 Changes In Design, Material Servicing, Or Part Number - Except For A Code 1 Change, Which Shall Be Processed As Provided In The Code Statement Shown Below, No Substitution Of Items Shall Be Made Until The Navicp-mech Contracting Officer Has Notified And approval Has Been Given By Issuance Of A Written Change Order. When Any Change In Design, Material, Servicing Or Part Number Is Made To Replace Or Substitute Any Item To Be Furnished On This Contract/purchase Order, The Contractor Shall Furnish, For The substituting/replacement Item, A Drawing And An Explanation Of The Reason For The Change, Explaining The Reason Therefor. If Finished Detail Drawings Are Not Available, Shop Drawings In The Form Used By The Manufacturer Will Be Acceptable For Government evaluation. When Notifying The Procurement Contracting Officer Of The Reasons For Making Substitutions, The Type Of Change Shall Be Indicated By Code Number In Accordance With One Of The Following Statements: code 1: Part Number Change Only - If The Manufacturer's Part Number Indicated Thereon Has Changed, But The Parts Are Identical In All Respects, Supply The Item And Advise Navicp-mech Immediately Of The New Part Number. code 2: Assembly (or Set Or Kit) Not Furnished - Used Following Detail Parts. code 3: Part Not Furnished Separately - Use Assembly. code 4: Part Redesigned - Old And New Parts Are Completely Interchangeable. code 5: Part Redesigned - New Part Replaces Old. Old Part Cannot Replace New. code 6: Part Redesigned - Parts Not Interchangeable. 4. Quality Assurance 4.1 Responsibility For Inspection - Unless Otherwise Specified In The Contract/purchase Order, The Contractor Is Responsible For The Performance Of All Inspection Requirements As Specified Herein. Except As Otherwise Specified In The Contract/purchase Order, the Contractor May Use His Own Or Any Other Facilities Suitable For The Performance Of The Inspection Requirements Specified Herein, Unless Disapproved By The Government. The Government Reserves The Right To Perform Any Of The Inspections Set Forth In The specification Where Such Inspections Are Deemed Necessary To Assure Supplies And Services Conform To Prescribed Requirements. 4.2 Responsibility For Compliance - All Items Must Meet All Requirements Of This Contract/purchase Order. The Inspection Set Forth In This Specification Shall Become A Part Of The Contractor's Overall Inspection System Or Quality Program. The Absence Of Any inspection Requirements Shall Not Relieve The Contractor Of The Responsibility Of Assuring That All Products Or Supplies Submitted To The Government For Acceptance Comply With All Requirements Of The Contract/purchase Order. Sampling In Quality Conformance does Not Authorize Submission Of Known Defective Material, Either Indicated Or Actual, Not Does It Commit The Government To Acceptance Of Defective Material. 4.3 Records - Records Of All Inspection Work By The Contractor Shall Be Kept Complete And Available To The Government During The Performance Of Contract/purchase Order And For A Period Of 365 Calendar Days After Final Delivery Of Supplies. 5. Packaging 5.1 Preservation, Packaging, Packing And Marking - Preservation, Packaging, Packing And Marking Shall Be In Accordance With The Contract/purchase Order Schedule And As Specified Below. mil-std 2073 Packaging Applies As Found Elsewhere In The Schedule 6. Notes 6.1 Ordering Information For Document References - The Department Of Defense Single Stock Point (dodssp), Website Http://www.dsp.dla.mil/, Provides Product Information For The Department Of Defense Index Of Specifications And Standards (dodiss) (i.e.military/federal Specifications And Standards), Data Item Descriptions (dids), And Other Dodssp Products. Most Specifications Can Obtained Directly From Http://quicksearch.dla.mil/ a. Availability Of Cancelled Documents - The Dodssp Offers Cancelled Documentsthat Are Required By Private Industry In Fulfillment Of Contractual Obligationsin Paper Format. Documents Can Be Requested By Phoning The Subscription Services Desk. b. Commercial Specifications, Standards, And Descriptions - These Specifications, Standards And Descriptions Are Not Available From Government Sources. Theymay Be Obtained From The Publishers Of The Applicable Societies. c. Ordnance Standards (os), Weapons Specifications (ws), And Navord Ostd 600 Pages - These Type Publications May Be Obtained By Submitting A Request To: commander, Indian Head Division, Naval Surface Warfare Center code 8410p, 101 Strauss Avenue indian Head, Md 20640-5035 d. On Post-award Actions, Requests For "official Use Only" And "noforn" (not Releasable To Foreign Nationals) Documents Must Identify The Government Contractnumber, And Must Be Submitted Via The Cognizant Defense Contract Management Command (dcmc) For certification Of Need For The Document. On Pre-award Actions Such Requests Must Be Submitted To The Pco For Certification Of Need For The Document. e. Noforn Military Specifications And Standards (including Amendments, Change Notices And Supplements, But Not Interim Changes) To Be Ordered From: contracting Officer navsup-wss code 87321 5450 Carlisle Pike p.o. Box 2020 mechanicsburg, Pa. 17055-0788 f. Nuclear Reactor Publications Assigned Navsea Documents And Identification Numbers (i.e. Navsea Welding Standard, Navsea 250-1500-1) Are To Be Ordered Enue: commanding Officer navsup-wss code 009 5450 Carlisle Pike p.o. Box 2020 mechanicsburg, Pa. 17055-0788 g. Technical Manuals Assigned Navsea Identification Numbers (i.e. Navsea Welding And Brazing Procedure, Navsea S9074-aq-gib-010/248) Are To Be Ordered From: commanding Officer navsup-wss code 1 Support Branch 700 Robbins Avenue philadelphia, Pa. 19111-5094 h. Interim Changes And Classified Specifications Must Be Obtained By Submitting A Request On Dd Form 1425 To Navsup-wss. 6.2 In Accordance With Opnavinst 5510.1 All Documents And Drawings Provided By The U.s. Navy To Perspective Contractors Must Include A "distribution Statement" To Inform The Contractor Of The Limits Of Distribution, And The Safeguarding Of The Information contained On Those Documents And Drawings. There Are 7 (seven) Seperate Distribution Statement Codes Used For Non-classified Documents And Drawings. The Definition For Each Is As Follows: a... Approved For Public Release; Distribution Is Unlimited. b... Distribution Authorized To Us Governments Agencies Only. c... Distribution Authorized To Us Government Agencies And Their Contractors. d... Distribution Authorized To Dod And Dod Contractors Only. e... Distribution Authorized To Dod Components Only. f... Further Distribution Only As Directed By Commander, Naval Sea Systems Command, Code 09t. x... Distribution Is Authorized To Us Government Agencies And Private Individuals Or Enterprises Eligible To Obtain Export Controlled Technical Data In Accordance With Opnavinst 5510.161. 6.3 Notice To Distributors/offerors - Consideration For Award Of Contract Shall Be Given Only To Authorized Distributors Of The Original Manufacturer's Item Represented In This Solicitation. If You Desire To Be Considered As A Potential Source For Award Of this Contract, Proof Of Being An Authorized Distributor Shall Be Provided On Company Letterhead Signed By A Responsible Company Official And Sent With Your Offer To The Procurement Contracting Officer. 1. Scope 1.1 This Contract/purchase Order Contains The Requirements For Manufacture And The Contract Quality Requirements For The Radar Set . 2. Applicable Documents 2.1 Applicable Documents - The Document(s) Listed Below Form A Part Of This Contract/purchase Order Including Modifications Or Exclusions. 2.1.1 "document References" Listed Below Must Be Obtained By The Contractor. Ordering Information Is Included As An Attachment To This Contract/purchase Order. 3. Requirements 3.1 Cage Code/reference Number Items - The Radar Set Furnished Under This contract/purchase Order Shall Be The Design Represented By Cage Code(s) reference Number(s). Cage _______ Ref. No. ;53711 6170342; 3.2 Marking - This Item Shall Be Physically Identified In Accordance with ;mil-std-130, Rev N, 16 Nov 2012; . 3.3 Changes In Design, Material Servicing, Or Part Number - Except For A Code 1 Change, Which Shall Be Processed As Provided In The Code Statement Shown Below, No Substitution Of Items Shall Be Made Until The Navicp-mech Contracting Officer Has Notified And approval Has Been Given By Issuance Of A Written Change Order. When Any Change In Design, Material, Servicing Or Part Number Is Made To Replace Or Substitute Any Item To Be Furnished On This Contract/purchase Order, The Contractor Shall Furnish, For The substituting/replacement Item, A Drawing And An Explanation Of The Reason For The Change, Explaining The Reason Therefor. If Finished Detail Drawings Are Not Available, Shop Drawings In The Form Used By The Manufacturer Will Be Acceptable For Government evaluation. When Notifying The Procurement Contracting Officer Of The Reasons For Making Substitutions, The Type Of Change Shall Be Indicated By Code Number In Accordance With One Of The Following Statements: code 1: Part Number Change Only - If The Manufacturer's Part Number Indicated Thereon Has Changed, But The Parts Are Identical In All Respects, Supply The Item And Advise Navicp-mech Immediately Of The New Part Number. code 2: Assembly (or Set Or Kit) Not Furnished - Used Following Detail Parts. code 3: Part Not Furnished Separately - Use Assembly. code 4: Part Redesigned - Old And New Parts Are Completely Interchangeable. code 5: Part Redesigned - New Part Replaces Old. Old Part Cannot Replace New. code 6: Part Redesigned - Parts Not Interchangeable. 4. Quality Assurance 4.1 Responsibility For Inspection - Unless Otherwise Specified In The Contract/purchase Order, The Contractor Is Responsible For The Performance Of All Inspection Requirements As Specified Herein. Except As Otherwise Specified In The Contract/purchase Order, the Contractor May Use His Own Or Any Other Facilities Suitable For The Performance Of The Inspection Requirements Specified Herein, Unless Disapproved By The Government. The Government Reserves The Right To Perform Any Of The Inspections Set Forth In The specification Where Such Inspections Are Deemed Necessary To Assure Supplies And Services Conform To Prescribed Requirements. 4.2 Responsibility For Compliance - All Items Must Meet All Requirements Of This Contract/purchase Order. The Inspection Set Forth In This Specification Shall Become A Part Of The Contractor's Overall Inspection System Or Quality Program. The Absence Of Any inspection Requirements Shall Not Relieve The Contractor Of The Responsibility Of Assuring That All Products Or Supplies Submitted To The Government For Acceptance Comply With All Requirements Of The Contract/purchase Order. Sampling In Quality Conformance does Not Authorize Submission Of Known Defective Material, Either Indicated Or Actual, Not Does It Commit The Government To Acceptance Of Defective Material. 4.3 Records - Records Of All Inspection Work By The Contractor Shall Be Kept Complete And Available To The Government During The Performance Of Contract/purchase Order And For A Period Of 365 Calendar Days After Final Delivery Of Supplies. 5. Packaging 5.1 Preservation, Packaging, Packing And Marking - Preservation, Packaging, Packing And Marking Shall Be In Accordance With The Contract/purchase Order Schedule And As Specified Below. mil-std 2073 Packaging Applies As Found Elsewhere In The Schedule 6. Notes 6.1 Ordering Information For Document References - The Department Of Defense Single Stock Point (dodssp), Website Http://www.dsp.dla.mil/, Provides Product Information For The Department Of Defense Index Of Specifications And Standards (dodiss) (i.e.military/federal Specifications And Standards), Data Item Descriptions (dids), And Other Dodssp Products. Most Specifications Can Obtained Directly From Http://quicksearch.dla.mil/ a. Availability Of Cancelled Documents - The Dodssp Offers Cancelled Documentsthat Are Required By Private Industry In Fulfillment Of Contractual Obligationsin Paper Format. Documents Can Be Requested By Phoning The Subscription Services Desk. b. Commercial Specifications, Standards, And Descriptions - These Specifications, Standards And Descriptions Are Not Available From Government Sources. Theymay Be Obtained From The Publishers Of The Applicable Societies. c. Ordnance Standards (os), Weapons Specifications (ws), And Navord Ostd 600 Pages - These Type Publications May Be Obtained By Submitting A Request To: commander, Indian Head Division, Naval Surface Warfare Center code 8410p, 101 Strauss Avenue indian Head, Md 20640-5035 d. On Post-award Actions, Requests For "official Use Only" And "noforn" (not Releasable To Foreign Nationals) Documents Must Identify The Government Contractnumber, And Must Be Submitted Via The Cognizant Defense Contract Management Command (dcmc) For certification Of Need For The Document. On Pre-award Actions Such Requests Must Be Submitted To The Pco For Certification Of Need For The Document. e. Noforn Military Specifications And Standards (including Amendments, Change Notices And Supplements, But Not Interim Changes) To Be Ordered From: contracting Officer navsup-wss code 87321 5450 Carlisle Pike p.o. Box 2020 mechanicsburg, Pa. 17055-0788 f. Nuclear Reactor Publications Assigned Navsea Documents And Identification Numbers (i.e. Navsea Welding Standard, Navsea 250-1500-1) Are To Be Ordered Enue: commanding Officer navsup-wss code 009 5450 Carlisle Pike p.o. Box 2020 mechanicsburg, Pa. 17055-0788 g. Technical Manuals Assigned Navsea Identification Numbers (i.e. Navsea Welding And Brazing Procedure, Navsea S9074-aq-gib-010/248) Are To Be Ordered From: commanding Officer navsup-wss code 1 Support Branch 700 Robbins Avenue philadelphia, Pa. 19111-5094 h. Interim Changes And Classified Specifications Must Be Obtained By Submitting A Request On Dd Form 1425 To Navsup-wss. 6.2 Notice To Distributors/offerors - Consideration For Award Of Contract Shall Be Given Only To Authorized Distributors Of The Original Manufacturer's Item Represented In This Solicitation. If You Desire To Be Considered As A Potential Source For Award Of this Contract, Proof Of Being An Authorized Distributor Shall Be Provided On Company Letterhead Signed By A Responsible Company Official And Sent With Your Offer To The Procurement Contracting Officer. 6.3 In Accordance With Opnavinst 5510.1 All Documents And Drawings Provided By The U.s. Navy To Perspective Contractors Must Include A "distribution Statement" To Inform The Contractor Of The Limits Of Distribution, And The Safeguarding Of The Information contained On Those Documents And Drawings. There Are 7 (seven) Seperate Distribution Statement Codes Used For Non-classified Documents And Drawings. The Definition For Each Is As Follows: a... Approved For Public Release; Distribution Is Unlimited. b... Distribution Authorized To Us Governments Agencies Only. c... Distribution Authorized To Us Government Agencies And Their Contractors. d... Distribution Authorized To Dod And Dod Contractors Only. e... Distribution Authorized To Dod Components Only. f... Further Distribution Only As Directed By Commander, Naval Sea Systems Command, Code 09t. x... Distribution Is Authorized To Us Government Agencies And Private Individuals Or Enterprises Eligible To Obtain Export Controlled Technical Data In Accordance With Opnavinst 5510.161. 1. Scope 1.1 This Contract/purchase Order Contains The Requirements For Manufacture And The Contract Quality Requirements For The Circuit Card Assemb . 2. Applicable Documents 2.1 Applicable Documents - The Document(s) Listed Below Form A Part Of This Contract/purchase Order Including Modifications Or Exclusions. 2.1.1 "document References" Listed Below Must Be Obtained By The Contractor. Ordering Information Is Included As An Attachment To This Contract/purchase Order. 3. Requirements 3.1 Cage Code/reference Number Items - The Circuit Card Assemb Furnished Under This contract/purchase Order Shall Be The Design Represented By Cage Code(s) reference Number(s). Cage _______ Ref. No. ;53711 6570452; 3.2 Marking - This Item Shall Be Physically Identified In Accordance with ;mil-std-130, Rev N, 16 Nov 2012; . 3.3 Changes In Design, Material Servicing, Or Part Number - Except For A Code 1 Change, Which Shall Be Processed As Provided In The Code Statement Shown Below, No Substitution Of Items Shall Be Made Until The Navicp-mech Contracting Officer Has Notified And approval Has Been Given By Issuance Of A Written Change Order. When Any Change In Design, Material, Servicing Or Part Number Is Made To Replace Or Substitute Any Item To Be Furnished On This Contract/purchase Order, The Contractor Shall Furnish, For The substituting/replacement Item, A Drawing And An Explanation Of The Reason For The Change, Explaining The Reason Therefor. If Finished Detail Drawings Are Not Available, Shop Drawings In The Form Used By The Manufacturer Will Be Acceptable For Government evaluation. When Notifying The Procurement Contracting Officer Of The Reasons For Making Substitutions, The Type Of Change Shall Be Indicated By Code Number In Accordance With One Of The Following Statements: code 1: Part Number Change Only - If The Manufacturer's Part Number Indicated Thereon Has Changed, But The Parts Are Identical In All Respects, Supply The Item And Advise Navicp-mech Immediately Of The New Part Number. code 2: Assembly (or Set Or Kit) Not Furnished - Used Following Detail Parts. code 3: Part Not Furnished Separately - Use Assembly. code 4: Part Redesigned - Old And New Parts Are Completely Interchangeable. code 5: Part Redesigned - New Part Replaces Old. Old Part Cannot Replace New. code 6: Part Redesigned - Parts Not Interchangeable. 4. Quality Assurance 4.1 Responsibility For Inspection - Unless Otherwise Specified In The Contract/purchase Order, The Contractor Is Responsible For The Performance Of All Inspection Requirements As Specified Herein. Except As Otherwise Specified In The Contract/purchase Order, the Contractor May Use His Own Or Any Other Facilities Suitable For The Performance Of The Inspection Requirements Specified Herein, Unless Disapproved By The Government. The Government Reserves The Right To Perform Any Of The Inspections Set Forth In The specification Where Such Inspections Are Deemed Necessary To Assure Supplies And Services Conform To Prescribed Requirements. 4.2 Responsibility For Compliance - All Items Must Meet All Requirements Of This Contract/purchase Order. The Inspection Set Forth In This Specification Shall Become A Part Of The Contractor's Overall Inspection System Or Quality Program. The Absence Of Any inspection Requirements Shall Not Relieve The Contractor Of The Responsibility Of Assuring That All Products Or Supplies Submitted To The Government For Acceptance Comply With All Requirements Of The Contract/purchase Order. Sampling In Quality Conformance does Not Authorize Submission Of Known Defective Material, Either Indicated Or Actual, Not Does It Commit The Government To Acceptance Of Defective Material. 4.3 Records - Records Of All Inspection Work By The Contractor Shall Be Kept Complete And Available To The Government During The Performance Of Contract/purchase Order And For A Period Of 365 Calendar Days After Final Delivery Of Supplies. 5. Packaging 5.1 Preservation, Packaging, Packing And Marking - Preservation, Packaging, Packing And Marking Shall Be In Accordance With The Contract/purchase Order Schedule And As Specified Below. mil-std 2073 Packaging Applies As Found Elsewhere In The Schedule 6. Notes 6.1 Ordering Information For Document References - The Department Of Defense Single Stock Point (dodssp), Website Http://www.dsp.dla.mil/, Provides Product Information For The Department Of Defense Index Of Specifications And Standards (dodiss) (i.e.military/federal Specifications And Standards), Data Item Descriptions (dids), And Other Dodssp Products. Most Specifications Can Obtained Directly From Http://quicksearch.dla.mil/ a. Availability Of Cancelled Documents - The Dodssp Offers Cancelled Documentsthat Are Required By Private Industry In Fulfillment Of Contractual Obligationsin Paper Format. Documents Can Be Requested By Phoning The Subscription Services Desk. b. Commercial Specifications, Standards, And Descriptions - These Specifications, Standards And Descriptions Are Not Available From Government Sources. Theymay Be Obtained From The Publishers Of The Applicable Societies. c. Ordnance Standards (os), Weapons Specifications (ws), And Navord Ostd 600 Pages - These Type Publications May Be Obtained By Submitting A Request To: commander, Indian Head Division, Naval Surface Warfare Center code 8410p, 101 Strauss Avenue indian Head, Md 20640-5035 d. On Post-award Actions, Requests For "official Use Only" And "noforn" (not Releasable To Foreign Nationals) Documents Must Identify The Government Contractnumber, And Must Be Submitted Via The Cognizant Defense Contract Management Command (dcmc) For certification Of Need For The Document. On Pre-award Actions Such Requests Must Be Submitted To The Pco For Certification Of Need For The Document. e. Noforn Military Specifications And Standards (including Amendments, Change Notices And Supplements, But Not Interim Changes) To Be Ordered From: contracting Officer navsup-wss code 87321 5450 Carlisle Pike p.o. Box 2020 mechanicsburg, Pa. 17055-0788 f. Nuclear Reactor Publications Assigned Navsea Documents And Identification Numbers (i.e. Navsea Welding Standard, Navsea 250-1500-1) Are To Be Ordered Enue: commanding Officer navsup-wss code 009 5450 Carlisle Pike p.o. Box 2020 mechanicsburg, Pa. 17055-0788 g. Technical Manuals Assigned Navsea Identification Numbers (i.e. Navsea Welding And Brazing Procedure, Navsea S9074-aq-gib-010/248) Are To Be Ordered From: commanding Officer navsup-wss code 1 Support Branch 700 Robbins Avenue philadelphia, Pa. 19111-5094 h. Interim Changes And Classified Specifications Must Be Obtained By Submitting A Request On Dd Form 1425 To Navsup-wss. 6.2 Notice To Distributors/offerors - Consideration For Award Of Contract Shall Be Given Only To Authorized Distributors Of The Original Manufacturer's Item Represented In This Solicitation. If You Desire To Be Considered As A Potential Source For Award Of this Contract, Proof Of Being An Authorized Distributor Shall Be Provided On Company Letterhead Signed By A Responsible Company Official And Sent With Your Offer To The Procurement Contracting Officer. 6.3 In Accordance With Opnavinst 5510.1 All Documents And Drawings Provided By The U.s. Navy To Perspective Contractors Must Include A "distribution Statement" To Inform The Contractor Of The Limits Of Distribution, And The Safeguarding Of The Information contained On Those Documents And Drawings. There Are 7 (seven) Seperate Distribution Statement Codes Used For Non-classified Documents And Drawings. The Definition For Each Is As Follows: a... Approved For Public Release; Distribution Is Unlimited. b... Distribution Authorized To Us Governments Agencies Only. c... Distribution Authorized To Us Government Agencies And Their Contractors. d... Distribution Authorized To Dod And Dod Contractors Only. e... Distribution Authorized To Dod Components Only. f... Further Distribution Only As Directed By Commander, Naval Sea Systems Command, Code 09t. x... Distribution Is Authorized To Us Government Agencies And Private Individuals Or Enterprises Eligible To Obtain Export Controlled Technical Data In Accordance With Opnavinst 5510.161. 1. Scope 1.1 This Contract/purchase Order Contains The Requirements For Manufacture And The Contract Quality Requirements For The Cable Assembly,spec . 2. Applicable Documents 2.1 Applicable Documents - The Document(s) Listed Below Form A Part Of This Contract/purchase Order Including Modifications Or Exclusions. 2.1.1 "document References" Listed Below Must Be Obtained By The Contractor. Ordering Information Is Included As An Attachment To This Contract/purchase Order. 3. Requirements 3.1 Cage Code/reference Number Items - The Cable Assembly,spec Furnished Under This contract/purchase Order Shall Be The Design Represented By Cage Code(s) reference Number(s). Cage _______ Ref. No. ;53711 7044468; 3.2 Marking - This Item Shall Be Physically Identified In Accordance with ;mil-std-130, Rev N, 16 Nov 2012; . 3.3 Changes In Design, Material Servicing, Or Part Number - Except For A Code 1 Change, Which Shall Be Processed As Provided In The Code Statement Shown Below, No Substitution Of Items Shall Be Made Until The Navicp-mech Contracting Officer Has Notified And approval Has Been Given By Issuance Of A Written Change Order. When Any Change In Design, Material, Servicing Or Part Number Is Made To Replace Or Substitute Any Item To Be Furnished On This Contract/purchase Order, The Contractor Shall Furnish, For The substituting/replacement Item, A Drawing And An Explanation Of The Reason For The Change, Explaining The Reason Therefor. If Finished Detail Drawings Are Not Available, Shop Drawings In The Form Used By The Manufacturer Will Be Acceptable For Government evaluation. When Notifying The Procurement Contracting Officer Of The Reasons For Making Substitutions, The Type Of Change Shall Be Indicated By Code Number In Accordance With One Of The Following Statements: code 1: Part Number Change Only - If The Manufacturer's Part Number Indicated Thereon Has Changed, But The Parts Are Identical In All Respects, Supply The Item And Advise Navicp-mech Immediately Of The New Part Number. code 2: Assembly (or Set Or Kit) Not Furnished - Used Following Detail Parts. code 3: Part Not Furnished Separately - Use Assembly. code 4: Part Redesigned - Old And New Parts Are Completely Interchangeable. code 5: Part Redesigned - New Part Replaces Old. Old Part Cannot Replace New. code 6: Part Redesigned - Parts Not Interchangeable. 4. Quality Assurance 4.1 Responsibility For Inspection - Unless Otherwise Specified In The Contract/purchase Order, The Contractor Is Responsible For The Performance Of All Inspection Requirements As Specified Herein. Except As Otherwise Specified In The Contract/purchase Order, the Contractor May Use His Own Or Any Other Facilities Suitable For The Performance Of The Inspection Requirements Specified Herein, Unless Disapproved By The Government. The Government Reserves The Right To Perform Any Of The Inspections Set Forth In The specification Where Such Inspections Are Deemed Necessary To Assure Supplies And Services Conform To Prescribed Requirements. 4.2 Responsibility For Compliance - All Items Must Meet All Requirements Of This Contract/purchase Order. The Inspection Set Forth In This Specification Shall Become A Part Of The Contractor's Overall Inspection System Or Quality Program. The Absence Of Any inspection Requirements Shall Not Relieve The Contractor Of The Responsibility Of Assuring That All Products Or Supplies Submitted To The Government For Acceptance Comply With All Requirements Of The Contract/purchase Order. Sampling In Quality Conformance does Not Authorize Submission Of Known Defective Material, Either Indicated Or Actual, Not Does It Commit The Government To Acceptance Of Defective Material. 4.3 Records - Records Of All Inspection Work By The Contractor Shall Be Kept Complete And Available To The Government During The Performance Of Contract/purchase Order And For A Period Of 365 Calendar Days After Final Delivery Of Supplies. 5. Packaging 5.1 Preservation, Packaging, Packing And Marking - Preservation, Packaging, Packing And Marking Shall Be In Accordance With The Contract/purchase Order Schedule And As Specified Below. mil-std 2073 Packaging Applies As Found Elsewhere In The Schedule 6. Notes 6.1 Ordering Information For Document References - The Department Of Defense Single Stock Point (dodssp), Website Http://www.dsp.dla.mil/, Provides Product Information For The Department Of Defense Index Of Specifications And Standards (dodiss) (i.e.military/federal Specifications And Standards), Data Item Descriptions (dids), And Ot