Fabrication Tenders

Description: CATEGORY: Excavation in trenches not exceeding 1 point 5 m wide and not exc 1 point 5m deep , Excavation in trenches exceeding 1 point 5 m depth but not exceeding 3 mtr and 1 point 5 m wide , Returing filling in trenches including spreading leveling watering and well ramming in layers not exceeding 25 cm , Removing excavated material not exc 50 m and depositing where directed , Material and labour for sand filling with clean dry find sand unwashed including gently punning around cables in trenches , Material and Labour PCC 1 2 4 type B1 using 20mm graded stone aggregate as in coping of poles , Material and Labour PCC 1 3 6 type C1 using 20 mm graded black trap oblique granite oblique basalt stone , Material and Labour well burnt bricks sub class B as in protection of cable laid dry flat abutting , Providing platform for transformer of size 2point 5 into 2 point 5 into 1 point 5m high from GL including , Supply erecting and fixing in true vertical position steel tubular swaged pole 410 SP 55 11 mtr long complete with cast iron , Supply fixing commissioning and testing of outdoor gang operated switch GOD single throw single break off load , Disconnecting Taking Out and shifting of the any make of transformer rating 100 KVA mounted on plinth , Supply lay connect test and commissioning of 3 core 95 Sqmm 11000 Volts grade Earthed XLPE , Material and Labour for Cable jointing kit for 11 KV Earthed grade cable for indoor termination , Supply laying and testing cable XLPE Insulated Earthed screened PVC bedded galvanized , Supply install commissioning and testing factory made Design verified as per IS IEC61439 1 , Supply and fixing cross arms bracing supports clamps and back plates fabricated from , Pin type porcela in vitreous white brown or green insulator including , Single disc assembly for tension with tension clamps , Aluminium conductor steel reinforced , Material and Labour for earthing complete with galvanized steel earth plate

Description: CATEGORY: 5MP Lowlight IR IP H 265 Vandal Resistance Motorised VF Bullet Camera , 5MP Lowlight IR IP H 265 Vandal Resistance Compact Bullet Camera , SITC OF 2MP IR IP H 265 Vandal Resistance Compact Dome Camera , SITC OF 5MP H265 Network Vandal Resistance PTZ Dome Camera , SITC OF 128GB Surveillance class SD card , Supply and Fixing of Pole Mount for PTZ Camera , SITC OF 32ch NVR with 4 Sata HDD Support , Supply and Fixing OF Surveillance Hard Disk 08 TB , SITC OF 55INCH 4K UHD LED Surveillance grade Monitor , SITC OF 10 Port Unmanaged Gigabit Switch with 8 Port PoE , SITC OF Aggregation L2 L2 switch with SFP ports for control ROOM , Supply Drawing and Testing stranded Single mode 6 Core glass optic fiber cable , Supply Drawing and Testing 4 pair 23 AWG Solid Bare Copper wire , Supply Grouting and Fixing of Pole OEM fabricated MS GI PIPE 100 MM DIA With RCC 1Mtr depth , Manual Moling HDD depth 1 Mtr , Supply and Drawing 40 mm HDPE Pipe , Supply and fixing Weather proof Pole Mount Box , Supply and fixing of Network Rack 4U , Supply and fixing Industry standard Small form factor pluggable SFP , Supply Installation Testing of 12 Port 19 1U Rack Mounted surface mounted aluminum CRCA , Supply Installation Testing and Comissioning of 18 U Floor standing rack , Supply Drawing and Testing of 3 Core copper cable , Supply Installation Testing and Commissioning of Optical Fiber Cable Patch Cord 1 Mr , Supply Installation Testing and Commissioning of Cat 6 U UTP , Supply Installation OTDR Testing and Fusion Splicing of Fiber Single mode Pigtail , Supply and Laying of medium duty PVC Conduit 25mm , Comprehensive Maintenance Charges for 3rd Year , Comprehensive Maintenance Charges for 4th Year , Comprehensive Maintenance Charges for 5th Year

Description: CATEGORY: Indoor Minidome Color Camera with IR, Power supply and mounting accessories , Indoor dome 3 Image sensor Multi pro multi-directional Color camera with IR, Power supply and mounting accessories , Outdoor dome 3 Image sensor Multi pro multi-directional Color camera with IR, Power supply and mounting accessories , Outdoor color camera with IR LED , Tab 5G , Network Video Recorder with VMS and 15 camera and 5 client viewer licence ad mounting accessories in network rack , Networking - 24 port L-2 Managed switch with mounting accessories in network rack , Networking - Network Rack , Networking - 1G Industrial grade media converter , Networking - SFP module single mode, 10G , Cabling and Laying - Indoor Cat 6 Cabling, connectors and accessories with PVC casing , Cabling and Laying - Outdoor Cat6 armoured cabling, connectors and accessories with HDPE casing , Cabling and Laying - Outdoor Armoured 4 core single mode OFC and accessories with HDPE casing , Cabling and Laying - Indoor 1.5 sqmm copper Flexible power cabling with connectors and accessories like MCB etc , Cabling and Laying - Outdoor 1.5 sqmm copper Armoured power cabling, connectors and accessories with HDPE casing , Cabling and Laying - 25mm MS Metallic pipe with proper gauge to withstand vehicle load for conduit if cables crossing the road , Civil works - Soft soil digging 1 feet depth, trenching and refilling , Civil works - Road or Concrete digging 1feet depth, trenching and refilling with concrete , IP66 Dust and water proof Junction Box at the bottom of Pole for power supply unit, FOC termination and FO component and exhaust fan for cooling and extension box with surge protector , Metallic Pole - 20 feet high. Along with concrete base of 1 feet and lightening arrestor , Fabricated MS steel pipe customized for mounting camera on wall , 100 Watt LED External lighting for illumination of camera view area at each pole , Proper earthing and lightening arrestor for cameras as per OEM , Relocation of existing camera , Installation and commissioning of cameras with VMS

Details: Description:- Supply, Installation, Testing & Commissioning Of A Pre-engineered, Factory Fabricated, assembled & Tested, Fully Integrated, Highly Efficient Pump, Ie5 Permanent Magnet Motors, Skid mounted, Complete Ready-to-connect Packaged Variable Speed Pressure Boosting System. The Pump shall Be Vertical Multi Stage Centrifugal Pump With 200 Cmh At 20mtrs Head With Shut Off Head Of 45 mtrs, High Efficiency Ie5 Motors With Integrated Variable Frequency Drive, Intelligent Multi-pump controller. Pump Shall Be Suitable For Existing System. Ced Coated. The Controller And Vfd Shall Be integrated Part Of Motor And Suitable To Ip55 Rating. Similar To Grundfos Cre 155-1-1 With 18.5kw motor With Inbuilt Vfd

Description: CATEGORY: SITC of factory built floor mounted chilled water double skin type horizontal vertical air handling units , 14200 CFM 65 mm wg static pressure 33.2 TR , 12000 CFM 65 mm wg static pressure 28.3 TR , 11000 CFM 65 mm wg static pressure 24.4 TR , 10190 CFM 65 mm wg static pressure 21.4 TR , 9600CFM 65 mm wg static pressure 27.7 TR , 9500 CFM 65 mm wg static pressure 23.8 TR , 9000 CFM 65 mm wg static pressure 27.7 TR , 200mm dia. 32 mm thick insulation , 150mm dia.32 mm thick insulation , 125mm dia. 32 mm thick insulation , 100 mm dia. 32 mm thick insulation , 80 mm dia. 32 mm thick insulation , 65 mm dia. 32 mm thick insulation , 50 mm dia. 32 mm thick insulation , SITC of valves strainers gauges in the chilled water plumbing , 65 mm dia. , 50 mm dia. , BALANCING VALVE WITH BUILT IN MEASURING FACILITY , Y STRAINER of Ductile CI Body flanged , Providing and fixing in position the industrial type pressure gauge with gun metal brass valves etc. , Providing and fixing in position the mercury in glass industrial type thermometer , Providing and fixing in position Air Vent for Automatic purging etc. , SITC of electronic self balancing pressure independent type dynamic balancing valve , 40mm dia , SITC of site fabricated GSS sheet metal rectangular round ducting , Thickness 0.80 mm sheet , Thickness 1.00 mm sheet , Thickness 1.25 mm sheet , Supply and fixing of acoustic lining of supply , Providing and fixing 40 mm dia , SITC of 4C x 4 Sqmm 1.1kV grade XLPE , Supplying and making end termination with brass , SITC of 3C x 1.5 Sqmm armoured Copper communication cable , Providing and fixing 6 SWG dia. G.I. wire , Dismantling of existing AHUs of different capacities , Dismantling of existing UVGI system , ismentalling of existing piping valves of different floor AHUs , 150 mm dia. , 125 mm dia. , 100 mm dia. , 80 mm dia.

Details: Description:- Supplying, Installation, Testing And Commissioning Of Electric Driven Main Fire Pump compatible To Deliver 1620 Lpm At A Head Of 88 Mtr Suitable For Automatic Operation And Consisting Of following, Complete In All Respects, As Required : A. Horizontal Type, Multistage, Centrifugal, Split Casing pump Of Cast Iron Body & Bronze Impeller With Stainless Steel Shaft, Mechanical Seal Conforming To Is 1520. B. Suitable Hp Squirrel Cage Induction Motor, Tefc, Synchronous Speed 1500 Rpm, Suitable For operation On 415 Volts, 3 Phase 50 Hz, Ac Supply With Ip 55 Protection For Enclosure, Horizontal Foot mounted Type With Class-'f' Insulation, Conforming To Is-325. C. M.s. Fabricated Common Base Plate, coupling, Coupling Guard, Foundation Bolts Etc. As Required. D. Suitable Cement Concrete Foundation duly Plastered With Anti Vibration Pads.

Description: 12261ms24i, 98050011, Quantity- 17.320 Mts. Scrap Condemned Unserviceable Ms Bed Plates, Water Tanks And Water Tank Cut Pieces, Ms Path Plates, Foot Path Plates, Sheets, Bin Cut Parts, Rack And Roller Path, Air Tank Cover Parts, Striker Casting Wear Plates, Sliding Doors, Swing Doors, Flap Doors, Ms Chequered Plates, Expansion Tank Parts, Ms Plates, Plate Cuttings, Wagon Doors, Dsl Engine Long Hood, Dummy Bogie Cut Parts, Cast Iron Surface Plates And Base Plates, Axle Counter Ms Frames, Baking Oven Cut Pieces, Ocb Duct, Welding Machine Outer Body, Inverter Empty Body, Tap Changer Ms Spares And Empty Body, Manipulator, Shaping Machine Ms Body, Ms Gates, Collapsible Gates, Base Plate, Short Hood Cabin Cut Parts, Tables, Racks, Lavatory Chute Brackets, Ms Travelling Base, Ms Danger Boards, Radiator Ms Spares, Ms Die Blocks, Ms Body Of Radiator Fan Motor, Capacitor Ms Body, Auxiliary Transformer Ms Empty Body, Ducts, Dust Bin Stand, Ht Load Brake Switch Body, Ms Transformer Body, Ventilator Motor Frames, Transformer Top Plate, Air Receiver, Storage Box Cut Parts, Coach Body Parts, Dust Bins, Lockers, Cattle Guard, Incinerator Chimney Parts, Incinerator Oven, Incinerator Cut Parts, Boxes, Wagon Doors Cut Pieces, Wagon Bfr End Plates And Cut Pieces, Ms Fuel Tanks [fire Prone], Boiler Tank Cut Pieces, Angles, Girder, Sheets Cut Pieces, Portable Stands, Channels ,fabricated Structures And Other Corroded Heavy Melting Scrap Of Different Thickness Of Sorts And Sizes, With Or Without Attachments. Note- 1. Gas Cutting Permitted For The Purpose Of Loading Only. 2. It Is The Responsibility Of The Purchaser To Ensure That Fuel Tanks To Be Filled With Water And Cleaned Thoroughly Free From Flammable Substances Before Cutting To Avoid Explosion Or Any Casualties. 3. Private Crane Permitted For Loading. Special Note- Gas Cutting For Fuel Tank Should Be Done In Open Area [cutting Must Be Kept Clear And Free Of Flammables] And Away From Bins [free From Recognized Hazards That Are Causing Or Are Likely To Cause Serious Harm] And Should Follow Fire-prevention And Fire-protection Measures. Location- [bin No- 261, Left Side Of Road No- 2]. Hsn Code- 72044900. Gst- 18 Percent. Note- Delivery On Actual Weighment Basis Only. Special Note: Overload Of The Carrying Capacity Of The Vehicle Will Not Be Permitted At The Time Of Taking Delivery As Per Mv Act 1988

Description: CATEGORY: Food thermometer , Lactometer , Refrigerator freezer Thermometer with hang stand , Heavy duty Plastic palle , Heavy duty Plastic crates for fruits and vegetables foldable , Todd Box for milk , Menu display board , Pin notice board , Colour coded garbage bins wet waste dry waste , Hand wash soap dispenser , Hand towel dispenser , Wet sign board , Cutlery sterilizer , Spoon sterilizer , SS 304 Commercial tawa , Tawa round , Strainer , Ms rack 6 tiers square pipe leg flat shelf with 3 side 2 inch brim , SS 304 masala box 12 , Ss 304 masala box 6 , Rice boiler , Ss commercial high pressure steam cabinet no boiler required , Idli steamer , Cabinet 2 door , SS Storage cupboard for cutlery and crockery , Commercial hand blender , Commercial beach juicer , Commercial sandwich griller , SS 304 Salamander oven , SS 304 Automatic Juice Machine , Heavy duty mixer , Bread toaster , Uv sterlizer wall mounted for knives , Soup container with lid , Salad Counter Fabricate Salad counter cum service counter Top 16gauge SS 304 grade sheet covering 20swg SS 304 grade sheet , Milk -tea dispenser , Juice dispenser , Food warmer , Chinese wok , SS 304 Stock pot with lid thick base 5mm sides- 18 gauge100 Litre 60 KG , SS 304 Stock pot with lid thick base 5mm sides- 18 gauge80 Litre 50 KG , SS 304 Stock pot with lid thick base, 5mm sides- 18 gauge60 Litre 40 KG , SS 304 material Saucepan with lid , SS 304 Fry pan , Handi with lid100 L , Handi with lid75 L , Handi with lid50 L , Handi with lid25 L , Lagan copper handi , SS 304 pressure cooker , SS 304 kadai 20 L , Ss kadai 25 L , Ss kadai 40 L , SS 304 storage containers small , GN pan SS 304 Food storage container with lid 1-1 8 inch , GN pan SS 304Food storage container with lid1-1 6 inch , GN pan SS304Food storage container with lid 1-1 4 inch , Ss 304 measuring jug 0.5l , Ss 304 oil dispenser 2l , Stainless steel water jug with lid

Details: Description:- "manufacturing And Supply Of Alumino Thermic Welding Portions Of 52kg/60 Kg/60ei-r260 As Approved By Rdso for Welding Of Rails 52kg/60kg/60ei-r260 Kg For 25mm Gap By The Process Of At Welding Along With Complete Accessories confirming To The Specification Laid Down In Indian Railway Standard Specification No.irst-19-2020 Up To Date Correction Slips with Single Shot Crucible Fitted With Automatic Tapping Thimble, 3 Pieces Pre Fabricated Mould (zircon Washed) Manually pressed Using Compressed Air Petrol/lpg Pre Heating For Execution Of Welding Of Rail Joint As Directed By The Engineer In Charge at Site. Note: 1. The Accessories Along With Welding Portion Shall Be Supplied As Per Annexure-i Of The Irussor - 2021. 2. Rate is Inclusive Of Transportation Of Above To Sse/p.way Stores. " For 60kg 90 Uts Rails

Details: Description:- Manufacturing And Supply Of Alumino Thermic Welding Portions Of 52kg/60 Kg/60ei- r260 As Approved By Rdso For Welding Of Rails 52kg/60kg/60ei-r260 Kg For 25mm Gap By The Process of At Welding Along With Complete Accessories Confirming To The Specification Laid Down In Indian railway Standard Specification No.irst-19-2020 Up To Date Correction Slips With Single Shot Crucible fittedwith Automatic Tapping Thimble, 3 Pieces Pre Fabricated Mould (zircon Washed) Manually pressed Using Compressed Air Petrol/lpg Pre Heating For Execution Of Welding Of Rail Joint As Directed by The Engineer In Charge At Site. Note: 1. The Accessories Along With Welding Portion Shall Be supplied As Per Annexure-i Of The Irussor - 2021. 2. Rate Is Inclusive Of Transportation Of Above To sse/p.way Stores. For 60kg 90 Uts Rails