Cleaning Tenders

Description: CATEGORY: Dismantling of old worn out Wall paneling with frame structure of Transmitter Hall and Technical area, shifting and disposal of dismantled debris material from the outside of the office premises , Wall paneling treatment in Transmitter Hall and Technical area , Providing, fabrication and fixing of cedar or teak wooden skirting 125mm x 15mm in Transmitter Hall and Technical area , Providing, fabrication and fixing of cedar or teak wooden planks 75mm x 15mm in Transmitter Hall and Technical area , Dismantling of old worn out false ceiling material with frame structure of transmitter hall and technical area, shifting and disposal of debris material from the outside of the office premises. , Providing, fabrication and fixing of false ceiling in Transmitter Hall and Technical area at HPT TV site Gurez as per drawings and respective layout drawings. , Providing of 600mm x 600mm hinged flap flushed doors and fixing it on the ceiling as per requirement of site at Gurez , Providing, fabrication, fixing and polishing of wooden table for emergency studio with console table top 25mm thick wooden board or commercial ply with Sunmica sheet 1mm thick , Providing, fabrication, fixing and polishing of heavy duty wooden workshop table with top made up of 25mm thick wood plank on top and wooden batten frame with wooden beading and moulding , Providing and applying of wall finish, putty and POP on walls to make smooth finish for premium emulsion paint at Transmitter Hall and Technical area, after touching on corners etc , Providing and applying two coats of wall primer on gypsum false ceiling and walls etc transmitter hall and technical area, after touching on corners, joints and screw heads etc as required , Providing and applying two to three coats of water based luxury emulsion on gypsum false ceiling and walls surface , Wooden surface to be cleaned and wooden putty to be applied and after rubbing with appropriate sand paper to smooth the surface two or more coat of wooden polish to be applied in wainscot and doors , Providing and applying of 50mm x 50mm x 12mm wooden cornice as per approved profile at all around false ceiling in transmitter hall and technical area , Fixing with complete wiring of 2ft x 2ft recessed mounted LED lights , Fixing with complete wiring of 1ft x 1ft recessed mounted LED lights

Description: Condemned Civil Structure Consisting Of 1] Cond. Qtr No. 298, 8 Unit, 2] Cond. Qtr No. 299, 8 Unit, 3] Cond. Qtr No. 300, 4 Unit, Total 20 Units, Total Qty- 01 By Lot. Free Delivery Period [fdp] For This Lot Has Been Fixed As 80 [eighty] Days. Above Mentioned Condemned Structure Are Offered Excluding Common Wall Of Adjacent Another Unit And Boundary Wall If Any Which Has Not Been Offered Or Sold . Therefore Such Type Of Cases Should Be Dealt With Proper Care During Dismantling So That Adjacent Unoffered And Unsold Unit Are Not Damage Or Broken In Any Way. Condition-1] Before Bidding Purchaser Are Invariably Advised To See The Lot And Also Check Whether Any Unit Of The Offered Lot Is Occupied In Any Way. If Found Occupied , In That Case It Is Required To Be Brought To The Notice Of The Custodian As Well As To This Office [ I.e. Sr.dmm/hwh ] In Writting At Least 24 Hours Prior To The Start Of Auction For Taking Further Necessary Action. 2] No Complaints/claim By The Purchaser Will Be Entertained In This Regard After E Auction Sale Is Completed. 3] The Sold Lot Will Be Handed Over To The Purchaser In Presence Of Concerned Custodian , Isa-sv, Rpf, Cdms And Other Personnel As The Case May Be , 4] Dismantling Work Of Sold Structure Is To Be Done By The Purchaser On His Own Arrangement By Providing Tools, Safety Gears, Machinery And Labour Required For The Purpose. 5] Purchaser Should Ensure To Keep A Safety Banner Around The Work Spot. 6] Any Loss / Damage That May Arise During Dismantling Work Due To Accident Etc, Shall Be The Sole Responsibility Of The Purchaser And No Claim On This Account Will Be Entertained By The Railways Under Any Circumstances, 7] Dismantling Of The Sold Lot Is Allowed Only Up To The Ground Level Of The Condemned Structures. 8] Dismantling Of The Condemned Structures [sold Lot] Will Take Place In Presence Of Engg. Officials. 9] Purchaser Shall Ensure That Dismantling Work Does Not Affect Or Endanger Safety Of Life And Railway Property In Near Vicinity.10] No Explosives Can Be Used For Demolishing, 11] Custodian / Engg. Official Has To Ensure That Debris Arisen Out Of Dismantling To Be Cleared By Purchaser In Proportion Of Delivery Of Released Materials And He Will Invariably Certify In Sale Completion Report That All Debris/waste Etc. Generated Has Been Cleared By Purchaser And The Land Is Made Clean, Clear And Level For Further Use.

Description: Condemned Civil Structure Consisting Of 1] Cond. Qtr No. 48a, 12 Unit, 2] Cond. Qtr No. 48d, 12 Unit, 3] Cond. Qtr No. 48j, 12 Unit, 4] Cond. Qtr No. 238, 4 Unit, 5] Cond. Qtr No. 239, 4 Unit, 6] Cond. Qtr No. 242, 4 Unit, Total 48 Units, Total Qty- 01 By Lot. Free Delivery Period [fdp] For This Lot Has Been Fixed As 80 [eighty] Days. Above Mentioned Condemned Structure Are Offered Excluding Common Wall Of Adjacent Another Unit And Boundary Wall If Any Which Has Not Been Offered Or Sold . Therefore Such Type Of Cases Should Be Dealt With Proper Care During Dismantling So That Adjacent Unoffered And Unsold Unit Are Not Damage Or Broken In Any Way. Condition-1] Before Bidding Purchaser Are Invariably Advised To See The Lot And Also Check Whether Any Unit Of The Offered Lot Is Occupied In Any Way. If Found Occupied , In That Case It Is Required To Be Brought To The Notice Of The Custodian As Well As To This Office [ I.e. Sr.dmm/hwh ] In Writting At Least 24 Hours Prior To The Start Of Auction For Taking Further Necessary Action. 2] No Complaints/claim By The Purchaser Will Be Entertained In This Regard After E Auction Sale Is Completed. 3] The Sold Lot Will Be Handed Over To The Purchaser In Presence Of Concerned Custodian , Isa-sv, Rpf, Cdms And Other Personnel As The Case May Be , 4] Dismantling Work Of Sold Structure Is To Be Done By The Purchaser On His Own Arrangement By Providing Tools, Safety Gears, Machinery And Labour Required For The Purpose. 5] Purchaser Should Ensure To Keep A Safety Banner Around The Work Spot. 6] Any Loss / Damage That May Arise During Dismantling Work Due To Accident Etc, Shall Be The Sole Responsibility Of The Purchaser And No Claim On This Account Will Be Entertained By The Railways Under Any Circumstances, 7] Dismantling Of The Sold Lot Is Allowed Only Up To The Ground Level Of The Condemned Structures. 8] Dismantling Of The Condemned Structures [sold Lot] Will Take Place In Presence Of Engg. Officials. 9] Purchaser Shall Ensure That Dismantling Work Does Not Affect Or Endanger Safety Of Life And Railway Property In Near Vicinity.10] No Explosives Can Be Used For Demolishing, 11] Custodian / Engg. Official Has To Ensure That Debris Arisen Out Of Dismantling To Be Cleared By Purchaser In Proportion Of Delivery Of Released Materials And He Will Invariably Certify In Sale Completion Report That All Debris/waste Etc. Generated Has Been Cleared By Purchaser And The Land Is Made Clean, Clear And Level For Further Use.

Description: CATEGORY: RESISTOR AS,PART NO-1353311 , PIN,PART NO-1511215 , BREATHER,PART NO-1577911 , RING SET,PART NO-3803472 , PIN,PART NO-4339379 , COVER,PART NO-5D1902 , RING SEAL,PART NO-7I1352 , RING WEAR,PART NO-8C5245 , MOUNT AS,PART NO-9W9930 , BUSHING,PART NO-4J6374 , COUPLING,PART NO-3215693 , COUPLING RH,PART NO- 3215694 , WASHER SPECIAL,PART NO-2342503 , TUBE AS,PART NO-3273935 , CLAMP-T BOLT,PART NO-2126934 , BUS BAR,PART NO-3989400 , BUS BAR,PART NO-3989401 , BUS BAR,PART NO-3575020 , VALVE GP-RELIEF,PART NO- 2234434 , TUBE,PART NO-3833492 , DIODE,PART NO- 3521145 , RESISTOR,PART NO-3634995 , RESISTOR,PART NO-3634996 , VALVE-CHECK,PART NO-1111460 , COIL AS- EVAPORATOR,PART NO-3697658 , VALVE GP- ACCUMULATOR CHARGING,PART NO-4921948 , ACCUMULATOR GP-HYDRAULIC,PART NO-3510320 , STRAINER,PART NO-2480363 , GROMMET,PART NO-3404192 , TUBE,PART NO-2678575 , SEAL 1.5 M,PART NO-5P5672 , SEAL,PART NO-5P5930 , SEAL,PART NO-3028935 , SEAL,PART NO-3029104 , SEAL,PART NO-3029140 , GASKET,PART NO-3030955 , SEAL,PART NO-3031297 , AIR CLEANER GP,PART NO-3080855 , COUPLING,PART NO- 5901978 , BOLT-12 POINT HEAD 5 BY 8-11X1.75-IN,PART NO-1762543 , PEDAL GP-GOVERNOR,PART NO-5961139 , VALVE GP-SOLENOID,PART NO-5457861 , SEAL,PART NO- 6222369 , COUPLING,PART NO-5901980 , SEAL,PART NO- 6222367 , PUMP GP-FUEL PRIMING,PART NO-4672659 , TUBE AS,PART NO-3789967 , HANDLE AS,PART NO-2521862 , GASKET,PART NO-2521863 , BRACKET,PART NO-3765502 , PLATE,PART NO-2790941 , SPACER,PART NO-2853692 , LOCKNUT,PART NO-0310249 , KNOB,PART NO-8Y6974 , SEAL-O-RING,PART NO-2069295 , BAR-BUS,PART NO- 3303356

Description: Condemned Civil Structure Consisting Of Abandoned 1] Building No 12 ,type- Ii, Unit-7, 2]building No 12a,type- Ii, Unit-1, 3]building No 14 ,type- I, Unit-14, Total - 22 Units , Total Qty- 01 By Lot. Above Mentioned Condemned Structure Are Offered Excluding Common Wall Of Adjacent Another Unit And Boundary Wall If Any Which Has Not Been Offered Or Sold . Therefore Such Type Of Cases Should Be Dealt With Proper Care During Dismantling So That Adjacent Unoffered And Unsold Unit Are Not Damage Or Broken In Any Way.condition-1] Before Bidding Purchaser Are Invariably Advised To See The Lot And Also Check Whether Any Unit Of The Offered Lot Is Occupied In Any Way. If Found Occupied , In That Case It Is Required To Be Brought To The Notice Of The Custodian As Well As To This Office [ I.e. Sr.dmm/hwh ] In Writting At Least 24 Hours Prior To The Start Of Auction For Taking Further Necessary Action. 2] No Complaints/claim By The Purchaser Will Be Entertained In This Regard After E Auction Sale Is Completed. 3] The Sold Lot Will Be Handed Over To The Purchaser In Presence Of Concerned Custodian , Isa-sv, Rpf, Cdms And Other Personnel As The Case May Be , 4] Dismantling Work Of Sold Structure Is To Be Done By The Purchaser On His Own Arrangement By Providing Tools, Safety Gears, Machinery And Labour Required For The Purpose. 5] Purchaser Should Ensure To Keep A Safety Banner Around The Work Spot. 6] Any Loss / Damage That May Arise During Dismantling Work Due To Accident Etc, Shall Be The Sole Responsibility Of The Purchaser And No Claim On This Account Will Be Entertained By The Railways Under Any Circumstances, 7] Dismantling Of The Sold Lot Is Allowed Only Up To The Ground Level Of The Condemned Structures. 8] Dismantling Of The Condemned Structures [sold Lot] Will Take Place In Presence Of Engg. Officials. 9] Purchaser Shall Ensure That Dismantling Work Does Not Affect Or Endanger Safety Of Life And Railway Property In Near Vicinity.10] No Explosives Can Be Used For Demolishing, 11] Custodian / Engg. Official Has To Ensure That Debris Arisen Out Of Dismantling To Be Cleared By Purchaser In Proportion Of Delivery Of Released Materials And He Will Invariably Certify In Sale Completion Report That All Debris/waste Etc. Generated Has Been Cleared By Purchaser And The Land Is Made Clean, Clear And Level For Further Use.

Description: Wheel Sharf - 25.000 Mt-delivery On Actual Weighment Basis. Lot No. 5312 25 01 01 Gtl Gy Ws Ap. Available With Sse C W Gy. Scrap, Condemned, Released, Unserviceable Wheel Swarf. Total Qty 25.000 Mt (approx) (delivery On Actual Weighment Basis). Available At Opposite To Atc In Bin No. 02 And 03 At Box N Depot Gooty. Ds-8 No. 531200054, Dated 20.12.24. Hsn Code: 720429 - Gst 18%. Note : For Taking Delivery Of Boring, Purchaser Should Ensure Coverage Of Body And Top Portion Of Truck To Arrest Leakage Of Boring In Enroute To Avoid Damages To The Vehicles Of Road User). Special Note : After Loading The Material Spilled Over Boring Chips Have To Be Cleaned By The Purchaser (i.e Loading Area) Note To The Bidders 1) Bidders May Visit The Site Of The Material For Physical Inspection Of The Material And Loading Spot Also, In All Aspects Before Bidding In E Auction.2)post Auction No Representation Shall Be Entertained.3) For Photos Of This Lot, Kindly Click On View Lot Image On Bottom Left Side. 4) Gas/chisel Cutting Is Permitted, If Required, For Easy Loading And Transportation Purpose, Only After Ensuring Sufficient Safety Measures Against Fire Hazards Etc To Avoid Any Mishap To Any Person, Railway Material Etc. Witnessing Officials To Ensure That The Lot Is Delivered As Per Lot Description 5) In Case Purchasers Require Usage Of Any Railway Assets/materials Such As Electricity/forklift Truck Etc. During The Process Of Delivery, They Are Required To Pay, The Prescribed Amount To Railways, As Directed By The Respective Custodian Of The Lot. 6) It Is The Responsibility Of The Purchaser/bidder To Return Excess Material, If Found During Gross Weighment, To The Nominated Premises Of The Custodian. 7) Clubbing Of The Lots, What So Ever, Is Not Permitted For Loading 8) Request For Fixation Of Delivery Point Should Be Invariably Raised In Ireps Online Only. Purchasers Are Requested To Make Use Of This Facility. No Representative Should Be Sent To The Office Of Sr.dmm/gtl For Collection Of Delivery Fixation Letter. As Soon As The Balance Sale Value Is Received By Railways Online, Delivery Order Will Be Issued Immediately, To Facilitate The Purchaser To Raise An Online Request For Fixation Of Delivery Point. 9) Railways Does Not Guarantee For Quality, Quantity Description Etc.

Description: CATEGORY: Fuel Filter , Oil Filter , Spark plug , HT Lead , Air cleaner assy , Fuel flexible pipe , Carborator , Ignition switch , Fuel cock , Fuse , Engine mounting pad , Bty 12V 32AH , Oil filter , Fuel filter , Fuel pipe 19x19 , Air Filter Dry Type , Distilled water , Coolant , Air filter , Fuel pipe , Carbon Brush , Bridge rectifier , Volt meter , Amp meter , Fuel filter assy , Oil filter assy , Air filter assy , Frequency meter , Temp gauge , MCB 63 Amp 3 Pole , Fan Belt , Amp mtr , Voltmeter , Emergency stop switch , Oil pressure gauge , Indication glass , Hrs meter , Fuel Tank hose pipe , Fuel tank cap , Door hinge , Door lock , Self Starter Bush , Armature for self str , Brush carier , Field coil for self str , Bendix drive , Stop solenoid sw with adopter , Rectifier plet , Self Starter Solenoid , Alternator Regulator TR 15 , Temp sensor , oil pressure switch LLOP , Ign sw , Dc Indication lamp , Ac Indication lamp , Cnnector 4 pole 63 AMP , Rotating diod , 1.5 Sqr mm single core copper wire , Fuel overflow pipe , Electric Voltage regulator , Injector assy , Voltage Reg , Fuel feed Pump , Rubber Coupling , Ignition Switch 3 pole , Self starter armature , Self starter Field coil , Alternator Carbon brush carier , Alternator carbon brush , Eng Stop Solenoid , 4 ST relay , DC Indication lamp , AC Indication lamp , Connector 4 pole 100 AMP , Air Filter , Diode plate , Push Rod , Oil pump , Single element fuel pump assy , Rotating diode , Push rod seal set , Over flow fuel pipe , Piston Std , Piston ring set , Cylinder Liner , Head Gasket , Injector nozzle , Fuel pump assy , Big end bearing set , Fly wheel housing seal , Eng overhaul gasket set , Inlet and exhaust valve set , AVR 3 phase , Rocker assy set , Fuel tank mtg clip , Silencer Assy , Nut with Bolt 13mm 1 inch length , High pressure pipe , Bty lead , Bty terminal positive and negative , Carbon Brush Set , Field coil for self starter , Rectifier plete

Details: Description :supply And Application Of Synthetic Acrylic Paint With Surface Adhesive And Binding Epoxy For Overhauling Facility As per Specification Given Below: 1)primer: Single Coat For 3150 Sqft With 100% Acrylic Binder & Micro Fine Pigments As Per Is 109/196 8 - 60 Ltrs/set. 2)putty: Applying Of Thin Coats Of Putty To Fill In All The Dents Formulated With Alkali Resistant Acrylic Co-polymer- 300 kg/set 3)paint: 2 Coats Around 3150 Sqft With Following Technical Specifications:nonflammable Enhanced Stain Resistance And Easy clean, Anti-fungal Protection,smooth Finish, Brushing And Rolling Application, Drying Time:30 Min,gloss / Sheen Levels: 1-10 At 60 D eg Gh.shelf Life: 3 Years [ Warranty Period: 12 Months After The Date Of Delivery ] ]

Description: BOQ ITEMS: Earthwork in excavation in the following types of soil and rock up to and including 1.5 mtr. Lead including bailing or pumping out any water accumulating inside the excavated pit or trench shoring strutting adequate protection to be taken during excavation transporting the excavated soil for all lead stacking selectively including disposing off the rubbish rock fragments excess spoils etc. lead upto 100 Mtrs. in the area as directed by the Engineer all complete as per drawing specification and direction of the Engineer. , Earth work in back filling with available earth including watering and compaction at all elevations around foundations walls wells tunnels pitsculverts trenches road approaches and in plinth filling and area filling as per specifications and drawings and as directed by the Engineer with selected spoil within a lead of 100 mtr., Disposal carriage of rubbish waste rock earth etc.dumped stacked at site by mechanical means including loading unloading and dressing properly lead upto 5 Km. and up to any lift includind cost of all labours and equipments. , Surface dressing of the ground in all kinds of soil including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish lead up to 50 m and lift up to 1.5 m., Supply mix place in position compact cure cement concrete 1 cement 3 coarse sand 6 graded stone aggregate 20 mm nominal size below foundations walls wells pits trenches etc. and in basin lining as per specifications drawings and directions of the Engineer and including cost of centring and shuttering but excluding cost of cement., Supply mix place in position compact and cure including testing of concrete specimens finishing surfaces as per specifications drawings and directions of the Engineer of the following grades of concrete with 20mm and down graded stone aggregate and coarse sand in super structure or any level excluding cost of centring and shuttering cement and reinforcement. M20 RCC PCC, Taking delivery from store or departmental yard bend bind and place the following types of reinforcement in all types of reinforced concrete work at all elevations including cleaning straightening cutting bending and binding with 18 SWG annealed wire or with welding such as tack lap butt etc with approved electrodes providing concrete cover blocks pin chairsnails supports of reinforcement etc. with all materials and labour complete as per drawings specifications and directions of Engineer excluding cost of reinforcement. , Install dismantle and remove the form work of approved quality including splay recess corners haunch etc. scaffolding necessary rendering of concrete surfaces after exposure including cost of all material and labours at all elevations. , Supply and laying in position brick work with designate 75 bricks in super structure etc in cement coarse sand mortar 1 isto 6 including mixing mortar laying bricks raking joints curing etc complete with all materials and labour as per drawings and specifications excluding cost of cement. , Providing and fixing 125 into 63 mm M. S. Hinges of approved quality and make., Providing and fixing ISI marked anodised aluminium tower bolt black finish Barrel type with necessary screws etc. complete 300 into 10 mm, Providing and fixing ISI marked anodised aluminium tower bolt black finish Barrel type with necessary screws etc. complete 150 into10 mm, Providing and fixing bright finished brass hanging type floor door stopper with necessary screws etc. complete., Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer having brand logo with IS 3564 embossed on the body door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm with double speed adjustment with necessary accessories and screws etc. complete., Providing and fixing aluminium handles ISI marked anodised anodic coating not less than grade AC 10 as per IS 1868 transparent or dyed to required colour or shade with necessary screws etc. complete 125 mm., Providing and fixing aluminium sliding door bolts ISI marked anodised anodic coating not less than grade AC 10 as per IS 1868 transparent or dyed to required colour or shade with nuts and screws etc. complete 300x16 mm, Cement concrete flooring 1 cement 2 coarse sand 4 graded stone aggregate finished with a floating coat of neat cement including cement slurry but excluding the cost of nosing of steps etc. Complete as per direction of EIC excluding cost of cement. 40 mm thick with 20 mm nominal size stone aggregate, Grading roof for water proofing treatment with Cement concrete 1 cement 2 coarse sand 4 graded stone aggregate 20 mm nominal size excluding cost of cement., 15mm thick minimum plastering with 1 cement 6 coarse sand to all faces of walls channels in roof and other structures at various elevations including mixing laying finishing curing and necessary scaffolding work complete as per drawings specifications with all materials and labours excluding cement Including Making grove if required. Work will be done upto 10 m height., Applying neat cement punning including cost of all materials labours etc. Complete as per direction of Engineer in charge excluding cost of cement, Supplying and applying two or more coats of white wash with lime to walls ceiling etc. At various elevations including preparation of surfaces cleaning etc.complete with all materials labour scaffolding work as per specifications ., Supplying and applying two or more coats of approved water proof cement paint over a coat of primer to exterior surfaces of concrete masonry plastered surfaces etc.at all elevations and including preparation of surface necessary scaffolding work etc.complete with all materials and labour Application of paint should be made as per manufacturer specifications to give an even shade. , Drain cleaning including disposal of rubbish up to 5 km all complete as per direction of EIC, Cleanning of chajja roof RWDC Floor corner drains etc., Painting with synthetic enamel paint of approved brand and manufacturer of required colour to give an even shade two or more coats on new or old work over a priming coat complete as per specification and direction of EIC. , Providing and fixing factory made ISI marked steel glazed doors windows and ventilator with beading and all members complete of standard rolled steel sections joints mitred and flash butt welded and sash bars tenoned and riveted including providing and fixing of hinges pivots including priming coat of approved steel primer but excluding the cost of other fittings complete all as per approved design sectional weight of only steel members shall be measured for payment., Taking delivery from store or departmental yard fabrication and erection of Structural steel work riveted bolted or welded in built up sections trusses and framed work including cutting hoisting fixing in position and applying a priming coat of approved steel primer all complete., Providing and fixing bright finished brass casement window fastener with necessary screws etc. complete., Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc.15 mm dia nominal bore, Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc. 20 mm dia nominal bore, Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc.25 mm dia nominal bore, Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc. 50 mm dia nominal bore, Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc. 100 mm dia nominal bore G.I.or CPVC.., Fixing of old G.I. pipes complete with G.I. fittings including trenching and refilling etc. 15 mm dia nominal bore, Fixing of old G.I. pipes complete with G.I. fittings including trenching and refilling etc.20 mm dia nominal bore, Fixing of old G.I. pipes complete with G.I. fittings including trenching and refilling etc. 25 mm dia nominal bore, Providing and fixing C.P. brass bib cock or Pillar Cock of approved quality conforming to IS 8931. 15 mm nominal bore., Providing and fixing C.P. brass stop cock concealed of standard design and of approved make conforming to IS 8931. 15 mm nominal bore., Demolishing brick work in cement mortar manually or by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of EIC, Demolishing R.C.C or PCC work manually or by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of EIC, Dismantling G.I. pipes external work including excavation and refilling trenches after taking out the pipes manually by mechanical means including stacking of pipes within 50 metres lead as per direction of EIC upto 150 mm dia, Providing and fixing or Renewing glass panes with putty and nails wherever necessary including racking out the old putty Float glass panes of thickness 5.5 mm, Renewing of old glass putty, Supplying laying in position stone masonary with Hard rock boulder with cement morter 1 cement 6coarse sand morter finishing the top with PCC reasonably smooth complete with curing and raking of joints including cost of all material equipments and labour excluding cost of cement. , Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete., Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade Old work one or more coats, Providing and fixing 35 mm thick factory made PVC door shutters with frame 65mm into 55mm with wall thickness 2 mm all complete as per manufacturers specification and direction of EIC. , Providing and fixing ISI marked flush door shutters conforming IS 2202 non decorative type core of block board construction with frame of 1st class hard wood and well matched comercial 3 plyveneering with vertical grains or cross bands and face veneers on both faces of shutters 30 mm thick including ISI marked stainless steel butt hinges with necessary screws., Providing and fixing precoated galvanised iron profile sheets 0.50 mm total coated thickness with zinc coating 120 grams per sqm as per IS 277 in 240 mpa steel grade 5 microns epoxy primer on both side of the sheet and polyester top coat 15 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by EIC. The sheet shall be fixed using self drilling self tapping screws with EPDM seal complete upto any pitch in horizontal vertical or curved surfaces including ridges barge board etc excluding the cost of purlins rafters and trusses and including cutting to size and shape wherever required. , Providing and fixing Following precoated galvanised steel sheet roofing accessories 0.50 mm total coated thickness Zinc coating 120 grams per sqm as per IS 277 in 240 mpa steel grade 5 microns epoxy primer on both side of the sheet and polyester top coat 15 microns using self drilling self tapping screws complete in Ridges plain 500 mm, Providing and fixing Following precoated galvanised steel sheet roofing accessories 0.50 mm total coated thickness Zinc coating 120 grams per sqm as per IS 277 in 240 mpa steel grade 5 microns epoxy primer on both side of the sheet and polyester top coat 15 microns using self drilling self tapping screws complete in Barge board up to 300mm, Providing and fixing Following precoated galvanised steel sheet roofing accessories 0.50 mm total coated thickness Zinc coating 120 grams per sqm as per IS 277 in 240 mpa steel grade 5 microns epoxy primer on both side of the sheet and polyester top coat 15 microns using self drilling self tapping screws complete in Gutter. 600 mm over all girth, Providing reinforced by organic fibres or inorganic synthetic fibres cement 6 mm thick corrugated sheets roofing up to any pitch and fixing with polymer coated J or L hooks bolts and nuts 8 mm dia. G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc. complete excluding the cost of purlins rafters and trusses including cutting sheets to size and shape wherever required. , Providing and fixing Following fibre cement high impact polypropylene reinforced roofing accessories in all colours with polymer coated J or L hooks bolts and nuts and or G.I. seam bolts and nuts G.I. plain and bitumen washers or with self drilling fastener and EPDM washer etc. complete Close fitting adjustable ridges, Providing and fixing Following fibre cement high impact polypropylene reinforced roofing accessories in all colours with polymer coated J or L hooks bolts and nuts and or G.I. seam bolts and nuts G.I. plain and bitumen washers or with self drilling fastener and EPDM washer etc. complete in Barge boards , Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch including fixing bolts nuts 8mm dia. G.I plain bitumen washers complete but excluding the cost of purlins rafters trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum ultra violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pocketsThe sheets shall be opaque or translucent clear or pigmented textured or smooth as specified. 2 mm thick corrugated, Repairing and maitenance of Rolling shutter in all respect including greasing repairing replacement of material to repairing of rolling shutter. Supply and fixing 27.5 cm long springs, Supply and fixing ball bearing, Supply and fixing precast slab M20 grade, Providing wood work in frames of false ceiling or floor partitions etc. sawn and fixed in position Sal wood and 15 mm thick light weight integral densified micro look edged with PVC top matt false floor tiles of size 595 into 595 mm including cost of all materials labours and as per direction of EIC. , Aluminum work for shutters of doors windows ventilators including providing and fixing hinges pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber neoprene gasket required Fittings shall be paid for separately Polyester powder coated aluminium minimum thickness of polyester powder coating 50 micron, Providing and fixing water closet squatting pan Indian type W.C. pan with 100 mm sand cast Iron P or S trap 10 litre low level white P.V.C. flushing cistern including flush pipe with manually controlled device handle leverconforming to IS 7231 with all fittings and fixtures complete including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580 into 440 mm with integral type foot rests., Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 into 260 into 350 mm or 340 into 410 into 265 mm sizes respectively., Providing and fixing wash basin or Kitchen Sink with C.I. brackets 15 mm C.P. Brass pillar taps 32 mm C.P. brass waste of standard pattern including painting of fittings and brackets cutting and making good the walls wherever require White Vitreous China Wash basin size 630 into 450 mm with a single 15 mm C.P. brass pillar tap all complete as per direction of EIC., Providing and fixing white vitreous china water closet squatting pan Indian type Orissa pattern W.C. pan of size 580 into 440 mm, Supply and fixing PVC connecting pipe 15 mm N B, Supply and fixing PVC flexible waste pipe 32 or 40 mm N B, Supply and fixing float ball valve 20 mm N B, Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25 into 25 mm made of G.I. wire of dia 3 mm including strengthening with 2 mm dia wire or nuts bolts and washers as required complete as per the direction of EIC. , Dismantling steel work in built up sections in angles tees flats and channels including all gusset plates bolts nuts cutting rivets welding etc. including dismembering and stacking within 50 metres lead., Dismantling following roofing including ridges hips valleys and gutters etc.and stacking the material within 50 metres lead of G.S. Sheet, Dismantling following roofing including ridges hips valleys and gutters etc and stacking the material within 50 metres lead of Asbestos cement sheet

Details: Description :supply And Installation Of Bis Listed Semi Automatic Stainless Steel Preventive Device With Ul Approved Clean Gas With Aut o Manual Reverse Stainless Steel Valve Nas 400 Mar Having Capacity 04 Kgs And Made Of Stainless Steel 304 Grade With Indian Railways logo On Each Unit And As Per Specification Attached. Make & Model - Nasa 400 Mar Cm/l-no. 7200017592 Is 15683 : 2018. (1) Oem/authorized D ealer Proof Of Purchase & Warranty Certificate To Be Submitted Along With The Material Supplied. Delivery Require At: Senior Section Engineer ( Electric) Office. store, Near 11 Kv Substation, , Traffic Colony, Mahesana Railway Station, Mahesana, Gujarat-384001 ( Mobile No: 9724093381) [ Warranty Period: 120 Mon ths After The Date Of Delivery ] ]