Electrical Cables Tender Results

CATEGORY: Disconnecting and reinstalling of electrical connection from the starter for submersible pump set upto 7.5 HP for repair of unsv submersible pump from borewell , M and L for flushing of borewell complete by a compressor and cleaning or flushing the bore well till the water is become free from any mud and clear for portable. , Material and labour for replacement of GI column pipe 50 mm dia medium grade 3m in length, both ends flanged, including nuts, bolts, washer and rubber gaskets etc. , M and L for taking out u_s electric driven pump set upto 7.5 HP, discharge 3 LPS head 70-80 m and submersible cable from bore for repair the submersible pump set. , M and L for split opening the submersible motor upto 7.5 HP capacity and taking out worn out winding and rewinding with copper winding wire and complete reassembling the motor. , M and L for split opening the submissible pump multi stage 3 phase upto 10 HP capacity and replacing the worn-out shaft sleeve, impeller and reassembling the pump. , M and L for lowering the submersible electric driven pump set discharge 3 LPS 70-80m head alongwith GI column pipe 50 mm bore flanged both side. , Supply and fixing in replacement of PVC insulated and sheathed cable with electrolytic grade annealed Cu conductor of size 10 Sqmm 3 core for submersible Pump Motors , S and F in replacement direct online submersible pump stater 3 phase 415 V suitable for upto 10 HP. , Repair of unsv LT panel bd outdoor type made out of CRCA sheet of 3.15 mm thick factory made CPRI approved standard a , Repair of earthing with galvanised steel earth plate electrode buried directly in ground with top edge of the plate not less than 1.5m below ground level , Repair of lorry filling point complete by RCC piller of size 45cm x 45cm x3.5 mtr ht with type B1 using 20 mm graded stone aggregate , Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel or wire armoured, electric power cables 1100V grade with std Al conductor , Supply, fixing and lowering MS reducer, bail plug, well cap, MS strip for centering, MS iron clamps, electric logging and sample strata box.

CATEGORY: Display table for Heat stress monitor , Display table for Multi gas detector , Display table for Explosive meter , Display table for Gas detector pump , Display table for Lux meter , Display table for electronic balance - digital , Display table for UV Spectro photo meter , Display table for UV light meter , Display table for Personal air sampler , Display table for High Volume air sampler , Display table for Temperature meter , Display table for Atomic Absorption Spectrophotometer - AAS , Display table for Respirable dust monitor , Display table for Human Vibration Meter , Display table for Direct reading instrument , Display table for Personal sampling Pump , Display table for electronic calibrator for air sampling pumps , Display table for Volatile Organic Compound Monitor - VOC , Display table for Chemical Absorbent Tubes , Display table for Alnor Vinometer , Display table for Personal Human Vibration , Display table for Different type of Reagents , Display table for Portable Sampling Pump , Display Panel for Electrical Display , Display table for Time delay Switches MCB , Display Panel for Welding Return Cables , Display table for Lighting Arresters , Display table for Emergency lamps charging , Display table for Guarding of Machinery , Show Case for Display types of grind wheels , Display Panel for chemistry of Fire , Display table for Fire Extinguishers , Display Unit for Safety Harness Safety Helmets Safety Shoe Aprons Fire suit Ear defenders Goggles - 1 each , Display Panel for Indian Standards Panel , Display table for GLC , Display table for Hazardous Chemicals , Display Panel for Occupational Diseases Symptoms , Display Panel for Prevention of Occupational Diseases , Display table for Gas Analyzer , Display table for Maffle furnace , Display table for Platinum crucible , Display table for Hot air oven , Display table for Hot Plate , Display table for Water Bath , Display table for Desiccators , Display table for Sound level meter , Display table for Noise dosimeter , Display table for Water analyzer , Display table for Turbidity meter , Display table for Physical Balance , Display table for Double distillation unit with sink , Display table for Insulator tester , Display table for Portable Breath Alcohol Meter , Display table for Portable Digital Weighing Machine , Display table for Portable Analytical Balance , Display table for Tig Welding Equipment , Display table for Oxy Gasoline Metal Cutting Torch System , Display table for Air cooling welding machine , Display table for Plasma Air Cutting Machine with Air Compressor , Display table for AC-DC GTAW Welding Machine

CATEGORY: Disconnecting and reinstalling of electrical connection from the starter for submersible pump set upto 7.5 HP for repair of unsv submersible pump from borewell , M and L for flushing of borewell complete by a compressor and cleaning or flushing the bore well till the water is become free from any mud and clear for portable. , Material and labour for replacement of GI column pipe 50 mm dia medium grade 3m in length, both ends flanged, including nuts, bolts, washer and rubber gaskets etc. , M and L for taking out u_s electric driven pump set upto 7.5 HP, discharge 3 LPS head 70-80 m and submersible cable from bore for repair the submersible pump set. , M and L for split opening the submersible motor upto 7.5 HP capacity and taking out worn out winding and rewinding with copper winding wire and complete reassembling the motor. , M and L for split opening the submissible pump multi stage 3 phase upto 10 HP capacity and replacing the worn-out shaft sleeve, impeller and reassembling the pump. , M and L for lowering the submersible electric driven pump set discharge 3 LPS 70-80m head alongwith GI column pipe 50 mm bore flanged both side. , Supply and fixing in replacement of PVC insulated and sheathed cable with electrolytic grade annealed Cu conductor of size 10 Sqmm 3 core for submersible Pump Motors , S and F in replacement direct online submersible pump stater 3 phase 415 V suitable for upto 10 HP. , Repair of unsv LT panel bd outdoor type made out of CRCA sheet of 3.15 mm thick factory made CPRI approved standard a , Repair of earthing with galvanised steel earth plate electrode buried directly in ground with top edge of the plate not less than 1.5m below ground level , Repair of lorry filling point complete by RCC piller of size 45cm x 45cm x3.5 mtr ht with type B1 using 20 mm graded stone aggregate , Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel or wire armoured, electric power cables 1100V grade with std Al conductor , Supply, fixing and lowering MS reducer, bail plug, well cap, MS strip for centering, MS iron clamps, electric logging and sample strata box.

CATEGORY: General Servicing of following capacity of DEA sets of different makes and models under various exchanges , Providing maintenance free New Lead acid Batteries following types , Repairing of control wiring of existing Conventional control panel of DEA set , Replacement of following defective accessories in the existing DG sets with new accessories , Servicing of Battery Charging Alternator or Dynamo , Repairing and General Servicing of the existing faulty radiator in existing DEA set , Servicing of the self starter of DEA set , Repairing of following faulty items in the self starter of DEA set , Supply of 12 volt battery operated self starter suitable for engine alternator set , Calibration of the fuel injection pump of following capacity of DEA sets of different makes and models under various exchanges , Extra charges for associated items of fuel pump, if required. , Repairing of existing canopy of 15 KVA DG set by providing suitable GI sheet on damaged roof , Supplying and fixing of 450 mm sweep ,1500 rpm exhaust fan suitable for working on 250 V single phase AC supply , Repairing and rewinding of existing 450 mm sweep ,1500 rpm exhaust fan , Repairing of existing AMF Panel of 15 KVA DG , Overhauling of faulty DG sets of following capacity , Dismentling of existing silent canopy or open type DEA Set of capacity up to 50 KVA , Shifting of existing dismentalled Silent canopy or open type DEA Set of capacity up to 50 KVA , Dismantling and Shifting of Electrical panels, Distribution boards, Changeover switch, conduit, Cables , Installation, testing , commissioning of Existing Silent canopy or open type Diesel Engine Alternator set of capacity up to 50 KVA , Removal of following faulty or burnt or damage parts in the existing up to 40 KVA DEA set , Removal of following faulty or burnt or damage parts in the existing above 40 KVA DEA to 75 KVA DEA set , Repairing of cylinder head , Repairing of Crank and crank shaft , Rewinding of following parts of existing alternator up to 50 KVA , S and F of 63 amps four pole on load change over switch , S and F 63 Amps TPN Switch fuse unit with HRC fuses , S and F of 100 amps four pole on load change over switch , S and F 100 Amps TPN Switch fuse unit with HRC fuses , Less for old faulty DG set battery of following capacity

CATEGORY: General Servicing of following capacity of DEA sets of different makes and models under various exchanges , Providing maintenance free New Lead acid Batteries following types , Repairing of control wiring of existing Conventional control panel of DEA set , Replacement of following defective accessories in the existing DG sets with new accessories , Servicing of Battery Charging Alternator or Dynamo , Repairing and General Servicing of the existing faulty radiator in existing DEA set , Servicing of the self starter of DEA set , Repairing of following faulty items in the self starter of DEA set , Supply of 12 volt battery operated self starter suitable for engine alternator set , Calibration of the fuel injection pump of following capacity of DEA sets of different makes and models under various exchanges , Extra charges for associated items of fuel pump, if required. , Repairing of existing canopy of 15 KVA DG set by providing suitable GI sheet on damaged roof , Supplying and fixing of 450 mm sweep ,1500 rpm exhaust fan suitable for working on 250 V single phase AC supply , Repairing and rewinding of existing 450 mm sweep ,1500 rpm exhaust fan , Repairing of existing AMF Panel of 15 KVA DG , Overhauling of faulty DG sets of following capacity , Dismentling of existing silent canopy or open type DEA Set of capacity up to 50 KVA , Shifting of existing dismentalled Silent canopy or open type DEA Set of capacity up to 50 KVA , Dismantling and Shifting of Electrical panels, Distribution boards, Changeover switch, conduit, Cables , Installation, testing , commissioning of Existing Silent canopy or open type Diesel Engine Alternator set of capacity up to 50 KVA , Removal of following faulty or burnt or damage parts in the existing up to 40 KVA DEA set , Removal of following faulty or burnt or damage parts in the existing above 40 KVA DEA to 75 KVA DEA set , Repairing of cylinder head , Repairing of Crank and crank shaft , Rewinding of following parts of existing alternator up to 50 KVA , S and F of 63 amps four pole on load change over switch , S and F 63 Amps TPN Switch fuse unit with HRC fuses , S and F of 100 amps four pole on load change over switch , S and F 100 Amps TPN Switch fuse unit with HRC fuses , Less for old faulty DG set battery of following capacity

Switch 5 Or 6 Amp,socket 5 Or 6 Amp,switch 15 Or 16 Amp,socket 15 Or 16 Amp,switch 5 Or 6 Amp,bell CATEGORY: Switch 5 or 6 amp , Socket 5 or 6 amp , Switch 15 or 16 amp , Socket 15 or 16 amp , Bell Push , Phenolic Laminated sheet 3mm , Fan Regulator , Celling Rose , Battan Holder , Angle Holder , Junction Box 4inch x 4inch , Gang Box , Electrical Round Sheet , Copper Cable 1.5 Sqmm , Copper Cable 2.5 Sqmm , 6 mmTwo Core Aluminium Wire , 10 mm Two Core Aluminium Wire , 23 OR 76 Flexible Pvc Insulated 40 OR 76 Flexible Wire , MCB 6 Amp SP , MCB 10 Amp SP , MCB 16 Amp SP , MCB 25 Amp SP , MCB 63 Amp SP , MCB 32 Amp DP , MCB 63 Amp DP , MCB 63 Amp TPN , MCB DP 2 OR 4 Way , Thimble 35 Sqmm , Thimble 50 Sqmm , Thimble 70 Sqmm , Cable Jointing kit , Ceiling Fan 1200 mm , Exhaust Fan 12inch , LED Tube light 9 Watt , Fan capacitor, 2.5 MFD , Fan Capacitor 3.15 MFD , Casing Caping 25 mm , Casing Nails , U Clip 8mm , U Clip 10mm , U Gitti 6mm to 8mm , Insulation Tap Roll , Call bell , Bell Ding Dong , Digital energy meter , Water Heater Ggeyser 25 Litre Storage , Electric Thermostat Auto Cut Off , Geyser Element 2000 watt

1.5 Tr 3 Star Inverter Split,1.9 Tr 3 Star Inverter Split,4.0 Kva Voltage Stablizer,5.0 Kva Voltage CATEGORY: 1.5 TR 3 STAR INVERTER SPLIT (Q3) , 1.9 TR 3 STAR INVERTER SPLIT (Q3) , 4.0 KVA VOLTAGE STABLIZER (Q3) , 5.0 KVA VOLTAGE STABLIZER (Q3) , COPPER PIPE (Q3) , Control cable 2.5 SQMM between indoor to outdoor unit (Q3) , CPVC pipe( for condensed water drain) having thermal stability for hot and cold water (Q3) , MS Angle Stand for Outdoor unit of Split A. C. (Q3) , Wiring point for light with 1.5 sq. mm. FRLSH PVC insulated multistrand single core copper conductor (Q3) , 36 Watt to 46 Watt indoor Recess mounting LED Square Fitting for Armstrong Ceiling having Powder coa (Q3) , 25 Amp Socket with board and Modular MCB complete set for AC connection. (Q3) , 6ways V TPN distribution board with additional Door without DPX3 160 MCCB complete in all respect, a (Q3) , surface/Flush mounting 4ways V TPN distribution board with additional Door without DPX3 160 MCCB com (Q3) , 63 Amp 4 pole MCCB(25 kA) Thermal Magnetic release (Q3) , 100 Amp 4 pole MCCB(25 KA) Thermal Magnetic release (Q3) , 6- 32Amp Single pole MCB (10 kA) C curve Cat A (Q3) , 6 sq. mm. PVC insulated 1100V grade25 mm dia heavy duty (2 mm thick) PVC conduit with one No. 4 sq. mm (Q3) , aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 (Q3) , 150sq. mm 3-1/2 core (Q3) , 70sq. mm 3-1/2 core (Q3) , 50 sq. mm 3-1/2 core (Q3) , GLAND Size- 400 sq. mm 3-1/2 core (Q3) , GLAND 150sq. mm 3-1/2 core (Q3) , GLAND 70sq. mm 3-1/2 core (Q3) , GLAND 50sq. mm 3-1/2 core (Q3) , LUG Size 400 Sqmm (Q3) , LUG Size-240Sqmm (Q3) , LUG Size-150 Sqmm (Q3) , LUG Size-70 Sqmm (Q3) , LUG Size-50 Sqmm (Q3) , LUG Size-35 Sqmm (Q3) , LUG Size-25 Sqmm (Q3) , ELECTRICAL PANEL 1000Amp, O/G 400- 2nos, 200-4nos, C/O switch 1000Amp 4 pole (Q3) , ELECTRICAL PANEL 400 Amp, O/G 100 Amp- 4 nos, 63 Amp -1 nos (Q3) , ELECTRICAL PANEL 200 Amp, O/G, 100 Amp -2 nos (Q3) , Danger board fabricated from 10 gauge M. S sheet as per I. E Rules (Q3) , Supply and burring of Safe Earthing Electrode T-39 Zn- Zinc Coated, (Q3) , GI wire 8 SWG (Q3) , G. I. strip 12mm x 3mm from earth electrode directly in the ground (Q3) , rubber matting 1800mm x 900mm x 12mm thick chequered (Q3) , C02 type fire extinguisher 4.5 kg capacity (Q3) , - Providing and fixing tiled false ceiling of specified materials of Size 595x595mm of true horizont (Q3) , Costruction of Panel Room by providing of all construction related materials Room size 3mtr x 4 mtr (Q3) , Antitermite treatment or Ground floor work (Q3) , die casting body tubler type universalhydrolic door closer (Q3) , 4mm thick ACP sheet to cover opening in Court Room (Q3) , Road cutting, Repairing, overhead fabricated pole type structure for road crossing (Q3)

CATEGORY: Custom Bid for Services - Item No 1 of BOQ Outsourcing of services to attend day to day electrical complaints operation of DG sets pumpsets and chloronome plant for 08 Hrs One shift at 14 Airmen Selection including all sundays and Public ho.. , Custom Bid for Services - Item No 2 of BOQ All as per the Item No 1 above but with semi skilled helper for 08 Hrs to assist the skilled trades man Sl Item No 01 for above work for 330 shifts , Custom Bid for Services - Item No 3 of BOQ Supply and fixing in replacement of LED street light fitting 45 Watt 230 V AC outdoor type with high pressure die cast aluminium housing for 02 Nos , Custom Bid for Services - Item No 4 of BOQ Supply fixing connecting and testing in replacement of 150 Watt LED flood light 230 Volt AC outdoor type with thermal management in multiple optics and equipped with IP 66 protection for 02 Nos , Custom Bid for Services - Item No 5 of BOQ Supply and fixing in replacement to ground with suitable pole mounting with OD of 76 mm connecting and testing 40 Watt LED Post Top Luminaire 230 Volt AC outdoor type with decorative post top for 360 indire.. , Custom Bid for Services - Item No 6 of BOQ Supply and fixing passing through pole cable 3 core PVC insulated unsheathed multistranded copper conductor of size 25 Sqmm for 25 M , Custom Bid for Services - Item No 7 of BOQ Supply fixing in replacement of transparent cover type street light junction box of size 168 mm x 253 mm x 115 mm for 2 Nos , Custom Bid for Services - Item No 8 of BOQ M L for laying of LT XLPE insulated screened PVC bedded galvanized steel strip or wire armoured electric power cables heavy duty with aluminium conductor 1100 volts grade for 50M , Custom Bid for Services - Item No 9 of BOQ M L for laying of LT XLPE insulated screened PVC bedded galvanized steel strip or wire armoured electric power cables heavy duty with aluminium conductor 1100 volts grade cross sectional area 70 Sq mm 3.. , Custom Bid for Services - Item No 10 of BOQ M L for removal of existing treatment from PCC poles and applying two coats of weather proof exterier emultion paint on old painted surface for 2 Nos , Custom Bid for Services - Item No 11 of BOQ ML for cleaning of feeder piller panel after dismantling the Incomming and out going connections from MCBs and replacing the old unserviceable Gland lugs nuts bolts for 02 Nos , Custom Bid for Services - Item No 12 of BOQ S F in replacement of MCCB 4 Pole 100125 Amps 415V 16 KA for 01 No , Custom Bid for Services - Item No 13 of BOQ S F in replacement of MCB TPN 63 Amp 4 Pole C Curve for 02 No , Custom Bid for Services - Item No 14 S F in replacement of MCB DP 3240 Amp C Curve for 03 Nos , Custom Bid for Services - Item No 15 S F in replacement of MCB SP 6 to 32 Amp C Curve for 05 Nos , Custom Bid for Services - Item No 16 of BOQ ML for Earthing complete with galvanized steel earth plate electrode 600x600x60mm thick buried directly in ground earth pit not less than 225 meters deep below ground level for 02 Nos , Custom Bid for Services - Item No 17 of BOQ M L for refilling of chemicals minimum 1015 ltr for each earth pit in existing chemical earthing at technical area for 05 Nos

CATEGORY: Modular Island Workbench with 8 base cabinet WORKBENCH WITH CASTOR WHEEL Refer to SL No 1 of BoQ in the Technical Specification , Modular Wall Facing Workbench with 2 base cabinet with castor wheels Refer to SL No 2 of BoQ in the Technical Specification , Modular Wall Facing Workbench with 2 base cabinet with castor wheels Refer to SL No 3 of BoQ in the Technical Specification , CRC Modular Wall facing Workbench Refer to SL No 4 of BoQ in the Technical Specification , Modular wallfacing Workbench with 1base cabinet with castor wheels Refer to SL No 5 of BoQ in the Technical Specification , Internal Electrical Connection 2.5 cable Refer to SL No 6 of BoQ in the Technical Specification , Fume Spot Extractor 1 arm Fume Refer to SL No 7 of BoQ in the Technical Specification , PP FRP Ducting Refer to SL No 8 of BoQ in the Technical Specification , Centrifugal Blower Refer to SL No 9 of BoQ in the Technical Specification , Fabrication and fixing of Sound Proof PartitionFabrication and fixing of Partition Refer to SL No 10 of BoQ in the Technical Specification , Fume Spot Extractor 1 arm Refer to SL No 11 of BoQ in the Technical Specification , Centrifugal Blower Refer to SL No 12 of BoQ in the Technical Specification , PP FRP Ducting Refer to SL No 13 of BoQ in the Technical Specification , Internal Electrical Connection Refer to SL No 14 of BoQ in the Technical Specification , Fume Hood 1500 mm Refer to SL No 15 of BoQ in the Technical Specification , PP FRP Ducting Refer to SL No 16 of BoQ in the Technical Specification , Fume Spot Extractor 1 arm Refer to SL No 17 of BoQ in the Technical Specification , Workbench in GI Construction Refer to SL No 18 of BoQ in the Technical Specification

CATEGORY: Steel rule , Knife Electrician , Hammer Ball peen , Combination pliers insulated , Neon tester pencil bit type , Screw driver set set of 5 , Soldering iron , Neon tester , Steel measuring tape , Wooden mallet , Multi meter , Hot wire Ammeter , Wheat stone Bridge , Electrical power drilling machine , Voltmeter MC , Voltmeter MC Multi range , Voltmeter centre zero , Voltmeter MI multi range , Ammeter MI , Ammeter MC , Frequency meter , Power Factor meter , Ammeter MC Centre zero , Single phase KWH meter analog digital , Three phase KWH meter analog Digital , 3Phase KW meter , Watt meter Dynamometer type , Clamp on ammeter , Tacho meter digital , Magnetic Flux Meter , Lux meter , Meter Reading Instrument MRI , Hydrometer , Hydraulic crimping tool for UG cable Crimping with bits , Crimping tool , Small crimping tools assorted , Wire stripper , Wiring board on stand , Pliers side cutting insulated , Pliers flat nose insulated , Pliers round nose insulated , Pliers long nose insulated , Screw driver heavy duty , Firmer chisel , Gauge wire imperial stainless steel marked in SWG and mm , Hammer Ball Peen , Hammer cross Peen , Scriber , Adjustable spanner , Contactor auxiliary contacts , Limit Switch , Rotary Switch , Four types relay , Knife Switch DPDT fitted with fuse Terminals , Knife Switch TPDT fitted with fuse terminals , Earth Plate , Earth Electrode , MCCB , ELCB and RCCB , Capacitors , Various Electronic components , All types of CFL lamp LED sets , Different types of cables , Cable Jointing Kit , Bus bar with brackets , Panel Accessories , Wiring Accessories including modular Industrial switch gears , Rechargeable battery , LED lights , Solar panels , Solar charge controller with manual switch Day lighting , Motion Detector , DC Power supply , Star Delta starter , Automatic Reverse Forward starter , Single phasing preventer , DOL starter , Soft starter , LeadAcidbattery75Ah , Battery Charger , Solar streetlight lamp set , Field regulator , Transformer single phase , DC Compound motor , DC shunt motor , DC series motor , MG Set consisting of squirrel cage induction motor 5 HP 400 V cycle with directly coupled compound generator3KW 250V withbuiltin panel board consisting of , LCD or LED projector , different type Domestic Appliances , DMX Controller , Rewinding Machine , Control Panel , Working Bench , Demonstration table