Painting Tenders

Description: BOQ ITEMS: Earthwork in excavation in the following types of soil and rock up to and including 1.5 mtr. Lead including bailing or pumping out any water accumulating inside the excavated pit or trench shoring strutting adequate protection to be taken during excavation transporting the excavated soil for all lead stacking selectively including disposing off the rubbish rock fragments excess spoils etc. lead upto 100 Mtrs. in the area as directed by the Engineer all complete as per drawing specification and direction of the Engineer. , Earth work in back filling with available earth including watering and compaction at all elevations around foundations walls wells tunnels pitsculverts trenches road approaches and in plinth filling and area filling as per specifications and drawings and as directed by the Engineer with selected spoil within a lead of 100 mtr., Disposal carriage of rubbish waste rock earth etc.dumped stacked at site by mechanical means including loading unloading and dressing properly lead upto 5 Km. and up to any lift includind cost of all labours and equipments. , Surface dressing of the ground in all kinds of soil including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish lead up to 50 m and lift up to 1.5 m., Supply mix place in position compact cure cement concrete 1 cement 3 coarse sand 6 graded stone aggregate 20 mm nominal size below foundations walls wells pits trenches etc. and in basin lining as per specifications drawings and directions of the Engineer and including cost of centring and shuttering but excluding cost of cement., Supply mix place in position compact and cure including testing of concrete specimens finishing surfaces as per specifications drawings and directions of the Engineer of the following grades of concrete with 20mm and down graded stone aggregate and coarse sand in super structure or any level excluding cost of centring and shuttering cement and reinforcement. M20 RCC PCC, Taking delivery from store or departmental yard bend bind and place the following types of reinforcement in all types of reinforced concrete work at all elevations including cleaning straightening cutting bending and binding with 18 SWG annealed wire or with welding such as tack lap butt etc with approved electrodes providing concrete cover blocks pin chairsnails supports of reinforcement etc. with all materials and labour complete as per drawings specifications and directions of Engineer excluding cost of reinforcement. , Install dismantle and remove the form work of approved quality including splay recess corners haunch etc. scaffolding necessary rendering of concrete surfaces after exposure including cost of all material and labours at all elevations. , Supply and laying in position brick work with designate 75 bricks in super structure etc in cement coarse sand mortar 1 isto 6 including mixing mortar laying bricks raking joints curing etc complete with all materials and labour as per drawings and specifications excluding cost of cement. , Providing and fixing 125 into 63 mm M. S. Hinges of approved quality and make., Providing and fixing ISI marked anodised aluminium tower bolt black finish Barrel type with necessary screws etc. complete 300 into 10 mm, Providing and fixing ISI marked anodised aluminium tower bolt black finish Barrel type with necessary screws etc. complete 150 into10 mm, Providing and fixing bright finished brass hanging type floor door stopper with necessary screws etc. complete., Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer having brand logo with IS 3564 embossed on the body door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm with double speed adjustment with necessary accessories and screws etc. complete., Providing and fixing aluminium handles ISI marked anodised anodic coating not less than grade AC 10 as per IS 1868 transparent or dyed to required colour or shade with necessary screws etc. complete 125 mm., Providing and fixing aluminium sliding door bolts ISI marked anodised anodic coating not less than grade AC 10 as per IS 1868 transparent or dyed to required colour or shade with nuts and screws etc. complete 300x16 mm, Cement concrete flooring 1 cement 2 coarse sand 4 graded stone aggregate finished with a floating coat of neat cement including cement slurry but excluding the cost of nosing of steps etc. Complete as per direction of EIC excluding cost of cement. 40 mm thick with 20 mm nominal size stone aggregate, Grading roof for water proofing treatment with Cement concrete 1 cement 2 coarse sand 4 graded stone aggregate 20 mm nominal size excluding cost of cement., 15mm thick minimum plastering with 1 cement 6 coarse sand to all faces of walls channels in roof and other structures at various elevations including mixing laying finishing curing and necessary scaffolding work complete as per drawings specifications with all materials and labours excluding cement Including Making grove if required. Work will be done upto 10 m height., Applying neat cement punning including cost of all materials labours etc. Complete as per direction of Engineer in charge excluding cost of cement, Supplying and applying two or more coats of white wash with lime to walls ceiling etc. At various elevations including preparation of surfaces cleaning etc.complete with all materials labour scaffolding work as per specifications ., Supplying and applying two or more coats of approved water proof cement paint over a coat of primer to exterior surfaces of concrete masonry plastered surfaces etc.at all elevations and including preparation of surface necessary scaffolding work etc.complete with all materials and labour Application of paint should be made as per manufacturer specifications to give an even shade. , Drain cleaning including disposal of rubbish up to 5 km all complete as per direction of EIC, Cleanning of chajja roof RWDC Floor corner drains etc., Painting with synthetic enamel paint of approved brand and manufacturer of required colour to give an even shade two or more coats on new or old work over a priming coat complete as per specification and direction of EIC. , Providing and fixing factory made ISI marked steel glazed doors windows and ventilator with beading and all members complete of standard rolled steel sections joints mitred and flash butt welded and sash bars tenoned and riveted including providing and fixing of hinges pivots including priming coat of approved steel primer but excluding the cost of other fittings complete all as per approved design sectional weight of only steel members shall be measured for payment., Taking delivery from store or departmental yard fabrication and erection of Structural steel work riveted bolted or welded in built up sections trusses and framed work including cutting hoisting fixing in position and applying a priming coat of approved steel primer all complete., Providing and fixing bright finished brass casement window fastener with necessary screws etc. complete., Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc.15 mm dia nominal bore, Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc. 20 mm dia nominal bore, Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc.25 mm dia nominal bore, Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc. 50 mm dia nominal bore, Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc. 100 mm dia nominal bore G.I.or CPVC.., Fixing of old G.I. pipes complete with G.I. fittings including trenching and refilling etc. 15 mm dia nominal bore, Fixing of old G.I. pipes complete with G.I. fittings including trenching and refilling etc.20 mm dia nominal bore, Fixing of old G.I. pipes complete with G.I. fittings including trenching and refilling etc. 25 mm dia nominal bore, Providing and fixing C.P. brass bib cock or Pillar Cock of approved quality conforming to IS 8931. 15 mm nominal bore., Providing and fixing C.P. brass stop cock concealed of standard design and of approved make conforming to IS 8931. 15 mm nominal bore., Demolishing brick work in cement mortar manually or by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of EIC, Demolishing R.C.C or PCC work manually or by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of EIC, Dismantling G.I. pipes external work including excavation and refilling trenches after taking out the pipes manually by mechanical means including stacking of pipes within 50 metres lead as per direction of EIC upto 150 mm dia, Providing and fixing or Renewing glass panes with putty and nails wherever necessary including racking out the old putty Float glass panes of thickness 5.5 mm, Renewing of old glass putty, Supplying laying in position stone masonary with Hard rock boulder with cement morter 1 cement 6coarse sand morter finishing the top with PCC reasonably smooth complete with curing and raking of joints including cost of all material equipments and labour excluding cost of cement. , Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete., Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade Old work one or more coats, Providing and fixing 35 mm thick factory made PVC door shutters with frame 65mm into 55mm with wall thickness 2 mm all complete as per manufacturers specification and direction of EIC. , Providing and fixing ISI marked flush door shutters conforming IS 2202 non decorative type core of block board construction with frame of 1st class hard wood and well matched comercial 3 plyveneering with vertical grains or cross bands and face veneers on both faces of shutters 30 mm thick including ISI marked stainless steel butt hinges with necessary screws., Providing and fixing precoated galvanised iron profile sheets 0.50 mm total coated thickness with zinc coating 120 grams per sqm as per IS 277 in 240 mpa steel grade 5 microns epoxy primer on both side of the sheet and polyester top coat 15 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by EIC. The sheet shall be fixed using self drilling self tapping screws with EPDM seal complete upto any pitch in horizontal vertical or curved surfaces including ridges barge board etc excluding the cost of purlins rafters and trusses and including cutting to size and shape wherever required. , Providing and fixing Following precoated galvanised steel sheet roofing accessories 0.50 mm total coated thickness Zinc coating 120 grams per sqm as per IS 277 in 240 mpa steel grade 5 microns epoxy primer on both side of the sheet and polyester top coat 15 microns using self drilling self tapping screws complete in Ridges plain 500 mm, Providing and fixing Following precoated galvanised steel sheet roofing accessories 0.50 mm total coated thickness Zinc coating 120 grams per sqm as per IS 277 in 240 mpa steel grade 5 microns epoxy primer on both side of the sheet and polyester top coat 15 microns using self drilling self tapping screws complete in Barge board up to 300mm, Providing and fixing Following precoated galvanised steel sheet roofing accessories 0.50 mm total coated thickness Zinc coating 120 grams per sqm as per IS 277 in 240 mpa steel grade 5 microns epoxy primer on both side of the sheet and polyester top coat 15 microns using self drilling self tapping screws complete in Gutter. 600 mm over all girth, Providing reinforced by organic fibres or inorganic synthetic fibres cement 6 mm thick corrugated sheets roofing up to any pitch and fixing with polymer coated J or L hooks bolts and nuts 8 mm dia. G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc. complete excluding the cost of purlins rafters and trusses including cutting sheets to size and shape wherever required. , Providing and fixing Following fibre cement high impact polypropylene reinforced roofing accessories in all colours with polymer coated J or L hooks bolts and nuts and or G.I. seam bolts and nuts G.I. plain and bitumen washers or with self drilling fastener and EPDM washer etc. complete Close fitting adjustable ridges, Providing and fixing Following fibre cement high impact polypropylene reinforced roofing accessories in all colours with polymer coated J or L hooks bolts and nuts and or G.I. seam bolts and nuts G.I. plain and bitumen washers or with self drilling fastener and EPDM washer etc. complete in Barge boards , Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch including fixing bolts nuts 8mm dia. G.I plain bitumen washers complete but excluding the cost of purlins rafters trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum ultra violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pocketsThe sheets shall be opaque or translucent clear or pigmented textured or smooth as specified. 2 mm thick corrugated, Repairing and maitenance of Rolling shutter in all respect including greasing repairing replacement of material to repairing of rolling shutter. Supply and fixing 27.5 cm long springs, Supply and fixing ball bearing, Supply and fixing precast slab M20 grade, Providing wood work in frames of false ceiling or floor partitions etc. sawn and fixed in position Sal wood and 15 mm thick light weight integral densified micro look edged with PVC top matt false floor tiles of size 595 into 595 mm including cost of all materials labours and as per direction of EIC. , Aluminum work for shutters of doors windows ventilators including providing and fixing hinges pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber neoprene gasket required Fittings shall be paid for separately Polyester powder coated aluminium minimum thickness of polyester powder coating 50 micron, Providing and fixing water closet squatting pan Indian type W.C. pan with 100 mm sand cast Iron P or S trap 10 litre low level white P.V.C. flushing cistern including flush pipe with manually controlled device handle leverconforming to IS 7231 with all fittings and fixtures complete including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580 into 440 mm with integral type foot rests., Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 into 260 into 350 mm or 340 into 410 into 265 mm sizes respectively., Providing and fixing wash basin or Kitchen Sink with C.I. brackets 15 mm C.P. Brass pillar taps 32 mm C.P. brass waste of standard pattern including painting of fittings and brackets cutting and making good the walls wherever require White Vitreous China Wash basin size 630 into 450 mm with a single 15 mm C.P. brass pillar tap all complete as per direction of EIC., Providing and fixing white vitreous china water closet squatting pan Indian type Orissa pattern W.C. pan of size 580 into 440 mm, Supply and fixing PVC connecting pipe 15 mm N B, Supply and fixing PVC flexible waste pipe 32 or 40 mm N B, Supply and fixing float ball valve 20 mm N B, Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25 into 25 mm made of G.I. wire of dia 3 mm including strengthening with 2 mm dia wire or nuts bolts and washers as required complete as per the direction of EIC. , Dismantling steel work in built up sections in angles tees flats and channels including all gusset plates bolts nuts cutting rivets welding etc. including dismembering and stacking within 50 metres lead., Dismantling following roofing including ridges hips valleys and gutters etc.and stacking the material within 50 metres lead of G.S. Sheet, Dismantling following roofing including ridges hips valleys and gutters etc and stacking the material within 50 metres lead of Asbestos cement sheet

Details: Description:- Periodicalmaintenanceoflcgates(cleaning,oiling,greasing,checkingof components, Replacement Of Worn Out/ Defective Parts I.e., Booms, Pedestals, Drums, Lock Posts, Wire run, Rod Run Etc Other Than In Case Of Accident And Ensuring Proper Functioning Of The Lc Gate As mentioned In Scope Of Work & Schedule Of Activity For Maintenance Of Lc Gates In The Tender document.allconsumablesrequiredmaterialslikenuts,bolts,spindlebolt,oil,grease,paints, flexible Wire, Cement, Sand, Chips Etc. Shall Be Supplied By Contractor Except Boom, Pedestal, Drum, winch, Lock Post, Rodding, A/b Type Foundation, E-type Lock, Cross/vertical Wheels.(1 Numbers = Per Lc gate Per Year)

Details: -A.M.P. for the year 2025-26 on Parla Kasan Rachhera Harizan Basti road (Village road) DRRP No P0805VR0158 Km 0/00 to 1/00 & 2/00 to 3/00 ,Roda Nallah to Karkoh road DRRP No HP0805VR121 (Village road) Km 4/00 to 5/00 an 6/00 to 8/00, and Madan Ka Ghar to Samarahan Road Km 3/00 to 6/00 DRRP No HP0805VR0119. (SH- Providing and laying 25 mm thick bituminous concrete and thermoplastic lining in paint curve portion only)

Details: Description :ms Channel Of Size 150x75x6 [430 Mm Long] Along With Ms Plate Of Size 150x75x16mm I.e. Ms Plate [ref: 2] To Be Welded To The Ch annel [ref: 1] At One End As Per S. C. Rly.drg. No.c/els/lgd/ex.ftg/3/12, Alt 1 Ref.no.1 & 2. Note:- After Welding The Channels Should Be Coated with Black Enamel Paint As Per Is:8662/2004 Based On Rdso Amendment No.1 (rev.0). [ Warranty Period: 30 Months After The Date Of Delivery ] ]

Description: CATEGORY: , Lignocaine without Adrenaline Inj , Insulin Biphasic Aspart protamine 50 50 Novo Mix 50 , Inj Levocarnitine 1 gm 5ml , Inj Levocarnitine 500mg , Insulin NPH 40 IU 10 ml Inj , Insulin Lispro Biphasicinjection insulin Lispro 50 percent insulin lispro protamine suspension Humalog Mix50 50 Inj , Filgrastin 300 mg inj , Inj Paliperidone 100 MG , INJ VANCOMYCIN 100 MG , INJ METHYLCOBALAMINE 1500 MCG , Paracetamol with cysteine HCL monohydrate Infusion 1000mg 100ml , Biphasic Isophane Insulin 50 percent Soluble Insulin and 50 percent Isophane Insulin Insulin 50 50 Inj , INJ Somatropin Recombinant Human Growth 4 IU H5 , Levetiracetam 100 mg ml Syr Soln Liquid bottle of 100 ml , Sodium Valproate oral solution 200 mg 5ml Bott of 100 ml , Albendazole Syp each 5 ml containing 200 mg bott of 10 ml , Clotrimazole mouth paint 1 percent Bott of 15 ml , Gum paint Bott of 15 ml , Antiseptic mouth wash containing Sodium fluoride and triclosan bott of 100 to150ml , Clove Oil bott of 50 ml , Chlorhexidine mouth wash with 0 dot 12 percent sugar alcohol free bottle of 450 to 500 ml in amber coloured bottle , Minoxidil 5 percent lotion bott of 60 ml , Salicylic Acid 3 to 5 percent and Coal tar 1to 3 percent soln Bott , Hydrogen peroxide solution with snoilizer IP 20 volume 500 ml Bott , Cetirizine Syp 5mg 5ml bott of 60 ml , Cypropheptadine HCl 2 mg 5ml bott of 100 ml , Domperidone Syp 1 mg ml bott of 30 ml , Azithromycin 200 mg per 15 ml Syp , Metronidazole susp 200 mg 5ml bott of 60 ml , Ondansetron Syp 2 mg 5ml in bott of 30 ml , Levo- Salbutamol syrup 1 mg 5ml Bott of 100 ml , Sucralfate Suspension 1gm 10ml plus oxetacaine 10 mg 10ml bott of 100 ml , Disodium Hydrogen Phosphate Syrup , Povidone Iodine 10 percent solution bott of 100 ml , Iron Syp Paediatric each 5 ml containing elemental Iron 25 to 50 mg and Folic Acid 500 mcg bottle of 200 ml , Metronidazole Inj for IV use containing 500mg per bott of 100 ml , Antiseptic Solution bott of 500 ml Savlon , Cough expectorant syp 5 ml containing Diphenhydramine Hcl 14 dot 08mg ammonium chloride 0 dot 138 gm Sodium citrate 57 dot 03mg menthol 1 dot 14 mg in flavoured syp base bott of 100ml , Cremaffine white each 15 ml containing milk of magnesia 11 dot 25ml liq paraffin 3 dot 75ml bott of 170ml , Diclofenac Diethylamine Bp2 dot 32 percent Methyl Salicylate IP 10 percent plus Menthol 5 percent non Aquous Topical solution bott of 30 ml topical solution bott of 30 ml , Grillintus Dextromethorphan hbr 5 mg chlorpheniramine maleate2 dot 5 mg guaifensin 50mg ammonium chloride 60mg 5ml bott of 100 ml , Normal Saline 100 ml , Ornidazole plus Ofloxacin Syrup , Povidone Iodine 2 percent Gargle Bott of 100 ml , Spirit 400 ml , Travaprost plus Timolol Eye Drop , Moisturising cream with squalene aloe vera and vitamin E acetate Venusia Cream , Haematinic Syrup , Multivitamin Syrup bott of 200 ml , Phenol Soution , Paracetamol Syp 125 mg 5 ml bottle of 60 ml , Ibuprofen Syrup 100 mg 5ml Bott of 60 ml , Syrup Calcium Phosphate 80 mg 5 ml 200 ml bottle , Bromhexine Syp 5 ml containing 4 mg of Bromhexine Hcl Bott of 100 ml , Beclomethasone 0 dot 025 percent wvNeomycin 0 dot 5 percent wv and clotrimazole 1percent wv ear drops bott of 5 ml , Chlorhexidine Mouth Gel Hexigel , Lactulose 450ml Syrup , Ibuprofen plus Paracetamol Syrup

Description: CATEGORY: Jindal Cera Tata Shakti Prayag , Roofsheet 3000x1050mm Make Jindal Sail , PVC Connection Pipe 450mm , Towel Rail Stainless Steel 300mm Make Hindware Parryware Cera , Peg sets of 6 Hooks Make Hindware Parryware Cera , PVC Door mat , PVC Grating Make sudhakar Finolex Astral poly Supreme , GI Pipe 15mm Make Tata Jindal ISI Mark , GI Socket 15mm Make Tata Jindal ISI Mark , GI Tee 15mm Make Tata Jindal ISI Mark , GL elbow 15mm Make Tata Jindal ISI Mark , GL Union 15mm Make Tata Jindal ISI Mark , GI Pipe 20mmMake Tata Jindal ISI Mark , GI Union 20mm Make Tata Jindal ISI Mark , GI Tee 20mm Make Tata Jindal ISI Mark , GI Socket 20mm Make Tata Jindal ISI Mark , GI Reducer 20 x 15 mm Make Tata Jindal ISI Mark , GI Pipe 25MM Dia MakeTata Jindal ISI Mark , GI Pipe 32MM Dia Make Tata Jindal ISI Mark , GI Union with Washer 32MM Make Tata Jindal ISI Mark , GI Elbow 32MM Make Tata Jindal ISI Mark , GI Tee 50mm x 32mm Make Tata Jindal ISI Mark , GI Tee 32mm x 25mm Make Tata Jindal ISI Mark , GI Union With Washer 50MM Make Tata Jindal ISI Mark , GI Union 50MM Make Tata Jindal ISI Mark , GI Tee 50mm Make Tata Jindal ISI Mark , GI Socket 50mm Make Tata Jindal ISI Mark , GI Elbow 50MM Make Tata Jindal ISI Mark , PVC Pipe 100mm Make sudhaka Finolex Astralpoly Supreme , PVC Tee 100mm Make sudhakar Finolex Astral poly Supreme , M Seal Plumber 200 GM Pkt , Safeda , Ventilation Blind Complete 1220 x 1220mm , Portable fire extinguisher 5 Kgs ISI Mark , PVC Door 720 x 1800mmMake Rajsree , PVC Door 750 x 2000 Make Rajsree , Spring door Closoure ISI Mark , Hydrolic Door Closoure ISI Mark , Aluminium Window 1200 x 1200mm ISI Mark , Window Glass 600 x 300 mm ISI Mark , Wooden Fush door 7 x 2 feet ISI Mark , FLy mesh door 7 x 3 feet Make Tata Jindal ISI Mark , Wire mesh door ISI Mark , Tower Bolt 150mm ISI Mark , Bow Handle 100mm ISI Mark , Curtain Rod with Ring ISI Mark , False ceilling 600 x 600 mm , Ballies 4 inch dia , PBS Roll ISI Mark , SRT Make Tata Jindal ISI Mark , Iron Door 1800 x 900 mm Make Tata Jindal ISI Mark , ISMB 4100 x 200 mm Make Tata Jindal ISI Mark , Peep Hole Make Tata Jindal ISI Mark , Sand Bags , Pad Lock Make Godraj Harison , Shoes Rack Make Tata Jindal ISI Mark , Almarah Medium Make Tata Jindal ISI Mark , Vertified Tiles 600x600mm Make Johnson Kazaria Somani Asian , HDPE Water Tank 200 Ltrs Make Reno Sintex JS Polyplast Polycon , IWC Make Hindware Parryware Sera , Stainless steel sink Make Hindware Parryware Sera , Looking mirror 4 x 2 ft Make Prayag Shakti Janko , PVC Elbow 100mm Make Sudhakar Finolex Astral poly Supreme , Bed side Locker Make Tata Jindal ISI Mark , Inter Locking , Black Screw 1 inch 100 Nos per Pkt , Black Screw 1.5 inch 100 Nos per Pkt , Ceiling Tee 12 ft , Ceiling tTee 4 ft , Ceiling Tee 2 ft , Wall Angle 10 ft , PVC Cabinet looking mirror 4x1 point 2 ft , Bathroom looking mirror 2x1ft , Paint Brush 4 inch , Paint Brush 2 inch

Description: CATEGORY: Custom Bid for Services - MRPL Tender No 3900001394 and Service code 1037234 Refractory gunning charges as per tender document section and in GEM overall total lump sum rate to be quoted considering 10 metric tonne quantities including GST , Custom Bid for Services - MRPL Tender No 3900001394 and Service code 1037235 Refractory brick lining charges as per tender document section and in GEM overall total lump sum rate to be quoted considering 2000 each quantities including GST , Custom Bid for Services - MRPL Tender No 3900001394 and Service code 1037264 BA61401 MCC Heat Dry out charges as per tender document section and in GEM overall total lump sum rate to be quoted including GST , Custom Bid for Services - MRPL Tender No 3900001394 and Service code 1038153 Dismantling of refractory bricks as per tender document section and in GEM overall total lump sum rate to be quoted considering 50 metric tonne including GST , Custom Bid for Services - MRPL Tender No 3900001394 and Service code 1038154 Application of chemical like paint work as per tender document section and in GEM overall total lump sum rate to be quoted considering 5 metric tonne including GST , Custom Bid for Services - MRPL Tender No 3900001394 and Service code 1038155 SRU phase 3 sulphur pit brick lining as per tender document section and in GEM overall total lump sum rate to be quoted considering 75 square meters including GST , Custom Bid for Services - MRPL Tender No 3900001394 and Service code 1043546 Incinerator BA61 refractory gunning charges as per tender document section and in GEM overall total lump sum rate to be quoted considering 500 each including GST , Custom Bid for Services - MRPL Tender No 3900001394 and Service code 1043548 BA614 Incinerator refractory gunning charges as per tender document section and in GEM overall total lump sum rate to be quoted considering 500 each including GST , Custom Bid for Services - MRPL Tender No 3900001394 and Service code 1043549 Heat dry out charges of BA614 Incinerator as per tender document section and in GEM overall total lump sum rate to be quoted including GST

Description: Total Qty. = 607 Nos. And 01 Set, Description - 1. Voice Card 3 Nos. 2. Dtmf Card 133 Nos. 3. Pd Mux 5 Nos. 4. Psu Card 21 Nos. 5. Rcf 4 Nos. 6. Ddf Frame 4 Nos. 7. Auto Dialing System 2 Nos. 8. Smr Amaraja 4 Nos. 9. Smps Battery Charger 48v 11 Nos. 10. Smr Statcon 9 Nos. 11. Ct Box 20 Pair 6 Nos. 12. Power Supply Unit 6 Nos 13. Control Telephone 83 Nos 14. Magneto Telephone 91 Nos. 15. Auto Telephone 90 Nos 16. Modem 15 Nos 17. Power Supply Unit For Vhf 5 Nos 18. Dtmf Box (empty) 30 Nos 19. Head Qtr Equipment 4 Nos 20. 9u Rack 3 Nos. 21. Empty Paint Drum 2 Nos 22. U-link Panel 14 Nos 23. Coral Mux 13 Nos. 24. Emergency Portable T/p 01 Nos 25. Float Battery Charger 24v10amp 3 Nos 26. Btp 2 Nos 27. Face To Face System 5 Nos. 28. Krone Module (30 Channel) 2 Nos 29. Steel Location Hut 1 Nos 30. Vf Transformer 15 Nos. 31.puncom Charger 1 Nos. 32. Fare Display Board 2 Nos. 33. Gps Clock 1 Nos. 34. Digital Master Clock 1 Nos. 35. Digital Tower Clock 1 Nos. 36. Five Line Arrival/departure Display Board 2 Nos. 37. 4g Fct Phone 4 Nos 38. Vhf Ariel Antenna Accessories 1 Set 39. Socket Box 2 Nos. 40. Coaxial Cable 3 Nos. 41. Amararaja Charger 1 Nos 42. Jointer Tools Kit 25 Items 2 Nos. (remarks:- Material To Be Sold On As Is Where Is Basis And Material Sr. No. 38 To Be Delivered In Set. And Other Materials To Be Delivered In Nos.)

Description: CATEGORY: PVC Bend Pipe 75mm , Thread Cotton for Plumbing , PVC Bend Pipe 40mm , PVC Bend Pipe 110mm , Nails 95 mm , 17 No Screw , PVC Tee 40 mm , PVC Extention Nipple 15mm , GI Elbow 25 mm , PVC Tee 75 mm , PVC Tee 110 mm , GI Check Nut 25 mm , Intergral Water proofing compund liquid , Cement White , GI Check Nut 15 mm , Tiles , Nails wire 75mm , GI Bend 15 mm dia , Nails Wire 75 mm , PVC Gully 40mm , Nails wire 12.5 mm , Nails wire 65mm , Putty for glass , Glass pane Plain , Glass Pane Plain , Hack Saw Blade , Nails wire 32 mm , Nails wire 38 mm , Nails wire 40 mm , Nails wire 50mm , Nails wire 60mm , Particl board Pre laminated both side , Glass Pane Frosted , Nails Wire 25mm , Aluminium sheet 24 gauge , Stainless steel Grating 150 mm , PVC Waste coupling 38 mm , Symet Waste coupling 40 mm , Putty Oil for glass , Brass Door handle 100 mm , CP Bib cock 15 mm with spindle , CP Jet with complete , Aluminium Pegs 125 mm , Fevicol in 1 Kg SHSR , Aggregate course 20 mm , Glass pane , Aggregate fine , Vitreous china wash , CP Bib Cock 15mm fancy type , Vitreous china semi padestal pattern , CP Bottle trap 32 mm dia for WHB , CP fancy type angular stop core , 600 x 450 mm bevelled edge mirror , Stainless steel Grating 100 mm , Aluminium Pegs 100 mm , CP Pillar cock 15 mm fancy type , Brass Door handle 150 mm , Nails Wire 35 mm , Unbranded MS Rectangular Aperture of wire mesh fabric or cloth , Alumiinium Door Handle 200 mm , Enamel Synthetic exterior paint part

Description: CATEGORY: HDPE laminated Sand Bag of size 75x40 cm Sand colour and each bag having weight not less than 60 gms , SHS 6 mm thick size 120x120mm x 2.4m long for column with holes as per tech spec , ISMB 150 RSJ 150 x 75 mm 1.85 mtr long for beam conforming to relevant IS as per tech spec att , ISMB 150 RSJ 150 x 75 mm 60 Cm mtr long for beam conforming to relevant IS as per tech spec att , ISMB 125 RSJ 125 x 70mm 3.0m long for beam conforming to relevant IS as per tech spec att , SHS 6 mm thick size 70x70mm x 1.85m long for with conforming to IS as per tech spec att , 6mm thick MS plate 75x150mm welded with G1 beam connected with nut and bolts , 6mm thick MS plate 100mm x 100mm with a gap of 75mm as per tech spec att , 12mm dia nut bolt 75mm long inserted in 12mm dia eight nos hole in each column , 6mm thick MS base plate of size 150 x150 mm for SHS column as per tech spec att , Steel Roofing Trough of size 1630 mm x 613 mm x 180 mm made out of 2 mm thick as per tech spec att , MS hexagonal nuts Bolts and washers 12 mm dia 40 mm long. , LDPE sheet 3 m wide weighing 1.00 Kg per RM black in colour and shall contain as per tech spec att , Red Oxide primer conforming to relevant IS , Synthetic Enamel Paint Colour Green Ist quality conforming to relevant IS as per tech spec att , Thinner as per as per tech spec att . Sample to be approved before supply. , Dry distemper as per tech spec att. Sample to be approved before supply , Chalk whiting as per tech spec attSample to be approved before supply , Paint Brush 4 inch Make Amar or Lucky Sample to be approved before supply , Pre fabricated steel door of size 0.90m x 1.80m made out of 2mm thick MS black carbon sheet as per tech spec att , Supply of Swivel Bullet proof glass glass 750mm x500mm size 72 mm thick as per tech spec att , Silicone Gel sealent of 01 pack of 400 gms including aplicator gun , Ply wood 10 mm thick as per requirement for flat surface , Foundation bolts of 16 mm dia and 250 m long with nut bolts washer etc. , Stone Aggregate to be crushed rock or gravel 20mm graded confirming to relevant IS , Natural sand confirming to relevant IS as per tech spec att , Stone Aggregate to be crushed rock or gravel 40mm graded confirming to relevant IS as per tech spec att , Rapidite quick setting liquid. , Integrated water proofing compound. , Drilling machine portable type, electrically driven , Aluminimum straight edge 50mm squre 2mm thick 1800mm long , wooden Flat Gurmala , Water leveling pipe PVC 100 mtr , Hand Rivet Gun machine , Drill bit 6mm dia , Drill bit 8mm dia , Drill bit 10mm dia , Tape measuring metallic 30 M , Mason trowel Karchi , Tasla Iron 18 inch , Shovel with wooden handle , Axe Picks with wooden handle , Fawda with wooden handle , Crobar 5 feet long , Rammer with wooden handle of WT 5 AND 10 KG , Sieve for sieving fine and crose AGG 900 x 1500mm made of angle iron frame with stand , Brick Hammer 1,2 Kgs , Cutting plier Insulate 6 inch , Screw Driver 12 INCH with insulated plastic , Digital Clamp Meter , Pipe Wrench 12 inch , Pipe Wrench 18 inch , Adjustable spanner 12 inch , Hacksaw frame with 2 Blade , Hand Gloves Canvas with ISI Mark , Aluminium Sprit level 6 inch , Brick Line , Plumbob