Drawer Tenders

Details: Description:- Earthwork In Excavation By Mechanical Means (hydraulic Excavator)/manual Means For foundations And Floors Of The Bridges, Retaining Walls Etc. Including Setting Out, Dressing Of Sides, ramming Of Bottom, Getting Out The Excavated Material, Back Filling In Layers With Approved Material and Consolidation Of The Layers By Ramming And Watering Etc. Including All Lift, Disposal Of Surplus Soil up To A Lead Of 300m, All Types Of Shoring And Strutting With All Labour And Material Complete As Per drawing And Technical Specification As Directed By Engineer In Charge. Note: This Item Will Be Used For excavation Work In Connection With Other Miscellaneous Works Also Like Side Drains, Foundation For ohe Masts And Other Miscellaneous Structures In Connection With Gauge Conversion, Doubling, New lines. All Kinds Of Soils

Description: BOQ ITEMS: Earthwork in excavation in the following types of soil and rock up to and including 1.5 mtr. Lead including bailing or pumping out any water accumulating inside the excavated pit or trench shoring strutting adequate protection to be taken during excavation transporting the excavated soil for all lead stacking selectively including disposing off the rubbish rock fragments excess spoils etc. lead upto 100 Mtrs. in the area as directed by the Engineer all complete as per drawing specification and direction of the Engineer. , Earth work in back filling with available earth including watering and compaction at all elevations around foundations walls wells tunnels pitsculverts trenches road approaches and in plinth filling and area filling as per specifications and drawings and as directed by the Engineer with selected spoil within a lead of 100 mtr., Disposal carriage of rubbish waste rock earth etc.dumped stacked at site by mechanical means including loading unloading and dressing properly lead upto 5 Km. and up to any lift includind cost of all labours and equipments. , Surface dressing of the ground in all kinds of soil including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish lead up to 50 m and lift up to 1.5 m., Supply mix place in position compact cure cement concrete 1 cement 3 coarse sand 6 graded stone aggregate 20 mm nominal size below foundations walls wells pits trenches etc. and in basin lining as per specifications drawings and directions of the Engineer and including cost of centring and shuttering but excluding cost of cement., Supply mix place in position compact and cure including testing of concrete specimens finishing surfaces as per specifications drawings and directions of the Engineer of the following grades of concrete with 20mm and down graded stone aggregate and coarse sand in super structure or any level excluding cost of centring and shuttering cement and reinforcement. M20 RCC PCC, Taking delivery from store or departmental yard bend bind and place the following types of reinforcement in all types of reinforced concrete work at all elevations including cleaning straightening cutting bending and binding with 18 SWG annealed wire or with welding such as tack lap butt etc with approved electrodes providing concrete cover blocks pin chairsnails supports of reinforcement etc. with all materials and labour complete as per drawings specifications and directions of Engineer excluding cost of reinforcement. , Install dismantle and remove the form work of approved quality including splay recess corners haunch etc. scaffolding necessary rendering of concrete surfaces after exposure including cost of all material and labours at all elevations. , Supply and laying in position brick work with designate 75 bricks in super structure etc in cement coarse sand mortar 1 isto 6 including mixing mortar laying bricks raking joints curing etc complete with all materials and labour as per drawings and specifications excluding cost of cement. , Providing and fixing 125 into 63 mm M. S. Hinges of approved quality and make., Providing and fixing ISI marked anodised aluminium tower bolt black finish Barrel type with necessary screws etc. complete 300 into 10 mm, Providing and fixing ISI marked anodised aluminium tower bolt black finish Barrel type with necessary screws etc. complete 150 into10 mm, Providing and fixing bright finished brass hanging type floor door stopper with necessary screws etc. complete., Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer having brand logo with IS 3564 embossed on the body door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm with double speed adjustment with necessary accessories and screws etc. complete., Providing and fixing aluminium handles ISI marked anodised anodic coating not less than grade AC 10 as per IS 1868 transparent or dyed to required colour or shade with necessary screws etc. complete 125 mm., Providing and fixing aluminium sliding door bolts ISI marked anodised anodic coating not less than grade AC 10 as per IS 1868 transparent or dyed to required colour or shade with nuts and screws etc. complete 300x16 mm, Cement concrete flooring 1 cement 2 coarse sand 4 graded stone aggregate finished with a floating coat of neat cement including cement slurry but excluding the cost of nosing of steps etc. Complete as per direction of EIC excluding cost of cement. 40 mm thick with 20 mm nominal size stone aggregate, Grading roof for water proofing treatment with Cement concrete 1 cement 2 coarse sand 4 graded stone aggregate 20 mm nominal size excluding cost of cement., 15mm thick minimum plastering with 1 cement 6 coarse sand to all faces of walls channels in roof and other structures at various elevations including mixing laying finishing curing and necessary scaffolding work complete as per drawings specifications with all materials and labours excluding cement Including Making grove if required. Work will be done upto 10 m height., Applying neat cement punning including cost of all materials labours etc. Complete as per direction of Engineer in charge excluding cost of cement, Supplying and applying two or more coats of white wash with lime to walls ceiling etc. At various elevations including preparation of surfaces cleaning etc.complete with all materials labour scaffolding work as per specifications ., Supplying and applying two or more coats of approved water proof cement paint over a coat of primer to exterior surfaces of concrete masonry plastered surfaces etc.at all elevations and including preparation of surface necessary scaffolding work etc.complete with all materials and labour Application of paint should be made as per manufacturer specifications to give an even shade. , Drain cleaning including disposal of rubbish up to 5 km all complete as per direction of EIC, Cleanning of chajja roof RWDC Floor corner drains etc., Painting with synthetic enamel paint of approved brand and manufacturer of required colour to give an even shade two or more coats on new or old work over a priming coat complete as per specification and direction of EIC. , Providing and fixing factory made ISI marked steel glazed doors windows and ventilator with beading and all members complete of standard rolled steel sections joints mitred and flash butt welded and sash bars tenoned and riveted including providing and fixing of hinges pivots including priming coat of approved steel primer but excluding the cost of other fittings complete all as per approved design sectional weight of only steel members shall be measured for payment., Taking delivery from store or departmental yard fabrication and erection of Structural steel work riveted bolted or welded in built up sections trusses and framed work including cutting hoisting fixing in position and applying a priming coat of approved steel primer all complete., Providing and fixing bright finished brass casement window fastener with necessary screws etc. complete., Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc.15 mm dia nominal bore, Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc. 20 mm dia nominal bore, Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc.25 mm dia nominal bore, Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc. 50 mm dia nominal bore, Providing and fixing following G.I. pipes complete with G.I. fittings including trenching and refilling etc. 100 mm dia nominal bore G.I.or CPVC.., Fixing of old G.I. pipes complete with G.I. fittings including trenching and refilling etc. 15 mm dia nominal bore, Fixing of old G.I. pipes complete with G.I. fittings including trenching and refilling etc.20 mm dia nominal bore, Fixing of old G.I. pipes complete with G.I. fittings including trenching and refilling etc. 25 mm dia nominal bore, Providing and fixing C.P. brass bib cock or Pillar Cock of approved quality conforming to IS 8931. 15 mm nominal bore., Providing and fixing C.P. brass stop cock concealed of standard design and of approved make conforming to IS 8931. 15 mm nominal bore., Demolishing brick work in cement mortar manually or by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of EIC, Demolishing R.C.C or PCC work manually or by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of EIC, Dismantling G.I. pipes external work including excavation and refilling trenches after taking out the pipes manually by mechanical means including stacking of pipes within 50 metres lead as per direction of EIC upto 150 mm dia, Providing and fixing or Renewing glass panes with putty and nails wherever necessary including racking out the old putty Float glass panes of thickness 5.5 mm, Renewing of old glass putty, Supplying laying in position stone masonary with Hard rock boulder with cement morter 1 cement 6coarse sand morter finishing the top with PCC reasonably smooth complete with curing and raking of joints including cost of all material equipments and labour excluding cost of cement. , Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete., Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade Old work one or more coats, Providing and fixing 35 mm thick factory made PVC door shutters with frame 65mm into 55mm with wall thickness 2 mm all complete as per manufacturers specification and direction of EIC. , Providing and fixing ISI marked flush door shutters conforming IS 2202 non decorative type core of block board construction with frame of 1st class hard wood and well matched comercial 3 plyveneering with vertical grains or cross bands and face veneers on both faces of shutters 30 mm thick including ISI marked stainless steel butt hinges with necessary screws., Providing and fixing precoated galvanised iron profile sheets 0.50 mm total coated thickness with zinc coating 120 grams per sqm as per IS 277 in 240 mpa steel grade 5 microns epoxy primer on both side of the sheet and polyester top coat 15 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by EIC. The sheet shall be fixed using self drilling self tapping screws with EPDM seal complete upto any pitch in horizontal vertical or curved surfaces including ridges barge board etc excluding the cost of purlins rafters and trusses and including cutting to size and shape wherever required. , Providing and fixing Following precoated galvanised steel sheet roofing accessories 0.50 mm total coated thickness Zinc coating 120 grams per sqm as per IS 277 in 240 mpa steel grade 5 microns epoxy primer on both side of the sheet and polyester top coat 15 microns using self drilling self tapping screws complete in Ridges plain 500 mm, Providing and fixing Following precoated galvanised steel sheet roofing accessories 0.50 mm total coated thickness Zinc coating 120 grams per sqm as per IS 277 in 240 mpa steel grade 5 microns epoxy primer on both side of the sheet and polyester top coat 15 microns using self drilling self tapping screws complete in Barge board up to 300mm, Providing and fixing Following precoated galvanised steel sheet roofing accessories 0.50 mm total coated thickness Zinc coating 120 grams per sqm as per IS 277 in 240 mpa steel grade 5 microns epoxy primer on both side of the sheet and polyester top coat 15 microns using self drilling self tapping screws complete in Gutter. 600 mm over all girth, Providing reinforced by organic fibres or inorganic synthetic fibres cement 6 mm thick corrugated sheets roofing up to any pitch and fixing with polymer coated J or L hooks bolts and nuts 8 mm dia. G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc. complete excluding the cost of purlins rafters and trusses including cutting sheets to size and shape wherever required. , Providing and fixing Following fibre cement high impact polypropylene reinforced roofing accessories in all colours with polymer coated J or L hooks bolts and nuts and or G.I. seam bolts and nuts G.I. plain and bitumen washers or with self drilling fastener and EPDM washer etc. complete Close fitting adjustable ridges, Providing and fixing Following fibre cement high impact polypropylene reinforced roofing accessories in all colours with polymer coated J or L hooks bolts and nuts and or G.I. seam bolts and nuts G.I. plain and bitumen washers or with self drilling fastener and EPDM washer etc. complete in Barge boards , Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch including fixing bolts nuts 8mm dia. G.I plain bitumen washers complete but excluding the cost of purlins rafters trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum ultra violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pocketsThe sheets shall be opaque or translucent clear or pigmented textured or smooth as specified. 2 mm thick corrugated, Repairing and maitenance of Rolling shutter in all respect including greasing repairing replacement of material to repairing of rolling shutter. Supply and fixing 27.5 cm long springs, Supply and fixing ball bearing, Supply and fixing precast slab M20 grade, Providing wood work in frames of false ceiling or floor partitions etc. sawn and fixed in position Sal wood and 15 mm thick light weight integral densified micro look edged with PVC top matt false floor tiles of size 595 into 595 mm including cost of all materials labours and as per direction of EIC. , Aluminum work for shutters of doors windows ventilators including providing and fixing hinges pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber neoprene gasket required Fittings shall be paid for separately Polyester powder coated aluminium minimum thickness of polyester powder coating 50 micron, Providing and fixing water closet squatting pan Indian type W.C. pan with 100 mm sand cast Iron P or S trap 10 litre low level white P.V.C. flushing cistern including flush pipe with manually controlled device handle leverconforming to IS 7231 with all fittings and fixtures complete including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580 into 440 mm with integral type foot rests., Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 into 260 into 350 mm or 340 into 410 into 265 mm sizes respectively., Providing and fixing wash basin or Kitchen Sink with C.I. brackets 15 mm C.P. Brass pillar taps 32 mm C.P. brass waste of standard pattern including painting of fittings and brackets cutting and making good the walls wherever require White Vitreous China Wash basin size 630 into 450 mm with a single 15 mm C.P. brass pillar tap all complete as per direction of EIC., Providing and fixing white vitreous china water closet squatting pan Indian type Orissa pattern W.C. pan of size 580 into 440 mm, Supply and fixing PVC connecting pipe 15 mm N B, Supply and fixing PVC flexible waste pipe 32 or 40 mm N B, Supply and fixing float ball valve 20 mm N B, Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25 into 25 mm made of G.I. wire of dia 3 mm including strengthening with 2 mm dia wire or nuts bolts and washers as required complete as per the direction of EIC. , Dismantling steel work in built up sections in angles tees flats and channels including all gusset plates bolts nuts cutting rivets welding etc. including dismembering and stacking within 50 metres lead., Dismantling following roofing including ridges hips valleys and gutters etc.and stacking the material within 50 metres lead of G.S. Sheet, Dismantling following roofing including ridges hips valleys and gutters etc and stacking the material within 50 metres lead of Asbestos cement sheet

Details: Shell Kit Items For Lws (752) Coaches A) One Coach Set Of Roof, 2 Mm Sidewall And En D Wall 1)roof Assembly To Drg No 75216001, Alt 'nil' - 1 No. 2)end Roof Assembly To Drg No 58116066, Alt 'g' - 2 Nos. 3)sidewall To Drg No 75214001, Alt 'nil' - 1 No. Welding Pin To Be Assembled As Per Drg No 58110037 (with Latest Sub Drawing 49516008 Alt 'a)' 4)end Wall To Drg No 74115001, Alt 'f' - 2 Nos. The Firm Shall Fulfil The Requirement As Per Icf//md/specn.200, Issue Status-01, Rev.04 With Amend Ment No. 01. The Firm Shall Fulfil The Requirement As Per Icf/md/spec-315, Issue Status-01, Rev.00. B) Partition Frames And Body Shell Items. 1) 75210012, Alt 'nil' - 1 No. 2) 75210002, Alt ' Nil' - 1 No. 3) 58210036, Alt 'a' - 2 Nos. 4) 75210003, Alt 'nil' - 1 No. 5) 67010011, Alt 'a' - 2 Nos. 6) Aaa 10488, Alt 'c' - 6 Nos. 7) 58110017, Alt 'b' - 2 Nos. 8) 58110015, Alt 'a' - 6 Nos. 9) 58110016, Alt 'a' - 3 Nos. 10) Aab10338, Alt 'nil' - 16 Nos. C) Under Frame Complete To Drg.no.67011001, Alt 'l' - 1 No . The Manufacturing Facility As Per Icf/md/spec-147, Issue Status-01 Rev.02 With Amendmen T No.01 Firm Has To Supply Roof And Sidewall Without Applying Etch Primer And The Firm Has To Apply Etch Primer On Roof And Sidewall In Icf After Shell Assembly. Special Condition : Packing For Roof A Nd Side Wall As Per Schedule A- (to Be Delivered To Shell) Complete Roof And Sidewall To Be Supplied With Welding Pins Welded To Roof Assembly As Per Drawing. Schedule B- (to Be D Elivered To Fur) Cap To Drg No 49516008002 Alt 'a' And Serrated Spring Washer To Drg No 495 16008003 Alt 'a' Of Required Quantity As Per Drawing Are To Be Packed In Suitable Polythene Bags Of 10 0 Microns Thickness With Printed Label With Complete Details Kept Inside The Polythene Bags. (complet E Details: 1. Item Description, 2. Qty In The Packing, 3. Date Of Packing, 4. Po No., 5. Type Of Coach, 6. Vendors Name & Address) "polythene Bags To Be Sealed Properly To Prevent Moisture An D Water Entry". A0 I) Packing For Roof And Side Wall As Per Icf/j&t/misc-2201, Alt 'e' Safety Instruction As Per Icf/j&t/sk-1867, Alt 'nil' Ii) Sl.no 16#b Of Note To Drawing No 582-1-6-002 Alt 'j' To Be Strictly Followed. Packing For End Wall As Per Drg.icf/j&t/sk-1809, Alt'a' Packing For Bo Dy Shell Items & Partition Frames.icf/j&t/sk-1865, Alt "a". Packing Condition For Underfram E As Per Icf/j&t/misc/2487, Alt 'b' The Underframe Should Be Supplied As Normal Side Up An D Side Bearer Side Down. All The Items Are To Be Supplied In Coach Sets. [safety Item] [ Wa Rranty Period: 30 Months After The Date Of Delivery ] [quantity Tolerance (+/-): 5 %age , Item Category : Normal , Total Po Value Variation Permitted: Max 8 Lacs ] ]

Details: Description:- Signallingexecutionsor(includinggst)-scopeofworkincludestrenching, transportation And Laying Of S&t Cable, Mechanised Drilling/ Micro Tunnelling Under Important/ Busy metal/concreteroad/railwaytrackandlayinggipipe,boringandpullingcable,supply, transportation And Fixing Of Galvanised Iron Pipe And Drawing Of Cables Inside The Pipe, Hiring Of jcb/hydra/poclainmachine(ingoodworkingcondition)forlevelling&dressingofground/ dismantling Structures, Erection Of Full Location Box, Painting Of Location Box, Lettering / Numbering termination Particulars, Equipments Names Etc. Inside Location Box, Transportation, Installation Of signal Post For Macls (2-aspect And 3/4 - Aspect), Transportation And Fixing Of Junction Type Route indicator,transportation,installationandpaintingwithretroreflectivetapeof slb/bslb/legend/stop Board Etc., Painting Of Two Coats Of Synthetic Enamel Paint Over One Coat Of primer On Main Signal Post With Signal Units, Surface Base And Complete Fittings & Shunt Signal Post with Signal Unit, Surface Base, Lettering / Numbering Termination Particulars, Equipments Names Etc on Signals/track Lead Junction Box, Transportation, Grouting/erection, Wiring As Per Approved Wiring diagram Of 19" Relay Rack/composite/q-series Relay Rack, Transportation, Installation And Charging of Secondary Cell 2 V (2 Volt 80ah/ 2 Volt 120 Ah/ 2 Volt 200 Ah), Transportation And Installation Of electric Point Machine, Painting & Lettering Of Point Machine With Ground Connections Complete And point Junction Box, Painting & Lettering Of Electric Lifting Barriers (elb), Installation Of Maintenance freeearthingandconventionalearthing,routingandconnectingalltheequipmentinthe equipment/relay Room To Seeb With 10 Sq. Mm Copper Cable, Provision Of Cement Concrete Enclosure for Earth Electrode As Per Approved Drawing, Cement Concrete For Miscellaneous Items.

Details: Description:- Fabrication Of Insitu Glued Insulated Joints For 52kg./60kg. Rail To Rdso Drg. No.t/5361 During Day/night And Conforming To The Manual For glued Insulated Rail Joint 1998 Issued By Ministry Of Railways, Rdso/lucknow And In Accordance With The Process Sheet Of Eastern Railway, Plant depot/mughalsarai At 4.11.98 With Supply Of All Fittings And Accessories Such As - [a] 950mm Long Fish Plate Or As Per Rdso Drawing [b] Hts Bolts And Nuts [c] Purchased Washers [d] Insulating Bushes [e] Insulating Channels [f] 10mm Thick End Post [g] Araldite [h] Hardener [i] Glass Cloth Carrier With All materials & Fixtures For Cleaning And Assembling Excluding Rail. [work Has To Be Execute By Rdso Approved Firm] Note - 950 Mm Long Fish Plates And Hts bolts Should Be Got Inspected By Rites Before Supply And Fixing In Track. Special Conditions - 1. The Work Is To Be Completed Within (12) Twelve Months from The Date Of Issue Of Letter Of Acceptance. 2. No Break Up In Rates Will Be Accepted. 3. Indian Railways General Condition Of Contract And Standard specification 2020 Will Be Binding On The Contract. 4. Current Goods And Service Tax Registration Is To Be Submitted. 5. 950mm Long F/plates And Hts Bolts should Be Got Inspected By Rites Before Supply And Fixing In Track. 6. Only The Firms Having Rdso Approval In Manufacturing Glued Insulated Joints Can participate In This Tender. 7. Tenderer[s] Have To Submit Certificate Regarding Approved Firms Under Rdso For Manufacturing And Fabrication Of Glued Joints as Per Rdso Drawing No.t-5361/t-5843.

Details: Description :manufacture And Supply Of Anti-creep Device For 10125 Mm Curved Switches With Zu-1-60 / 60e1a1 Thick Web Tongue Rails For 1 In 12 Turnouts F or B.g. (1673 Mm) For 60 Kg (uic)/60e1 On Psc Sleepers As Per Rdso Drg. No.rdso/t-8782 & Rdso/t-8783 (alt-2) Or Latest Alterations If Any Complete With Fit tings (including 27mm Dia. Hts Bolt & Nuts To Drg. No. Rdso/t-8786 & Rdso/t-8787 (alt-1) And Hardened Packing Plate To Drg. No. Rdso/t-8784 & Rdso/t-8 785. Acd Material Shall Be Cast Product Confirming To The Requirement Of Grade Sg-500/7 Of Is: 1865-1991 "indian Standard Iron Casting With Spheroidal Or N odular Graphite - Specification" (third Revision). Notes : (i) The 27 Mm Dia Hts Bolt And Nuts Shall Be Confirm To Is : 3757 & Is:6623 And Shall Be Manufacture d By Rdso Approved Vendor For Hts Bolts & Nuts. The Dimension Of Hts Bolts And Nuts Shall Be As Per Drawing No. Rdso /t-8786 & Rdso/t-8787. These Bolt and Nuts Are Shall Be Arranged And Supplied By The Suppliers /tenderers. (ii) Hardened Packing Plate Shall Confirm To Is : 6649 And Material 45c8 To Is:1570 ( hardened Tempered). The Dimension Of Hardened Packing Plate Shall Be As Per Drawing No. Rdso/t-8784 & Rdso/t-8785. Hardened Packing Plate Shall Be A rranged And Supplied By The Suppliers /tenderers. [ Warranty Period: 30 Months After The Date Of Delivery ] ]

Description: CATEGORY: Adhesive flags paper colour , Adhesive flag plastic , Attendance register 100 pages , Art Line drawing pen 0.1, 0.3, 0.5, 0.7mm , Binder clip 32mm , Binder clip 25mm , Binder clip 19mm , Blade 7 O Clock , Box File large size , Borosil glass medium set of 6 Nos , Calculator ordinary 12 digit , CD Mailer , CD Rewriteable , CD Marker pen , CD Writable , Cello tape brown big 2 inch size , Cello tape size 0.5 inch transparent , Cello tape size 1 inch transparent , Cello tape size 2 inch transparent , Cello tape red color 0.5 inch , Cello tape green color 0.5 inch , Cello tape blue color 0.5 inch , Checking pencil blue , Paper Gem clip 35 mm , Paper Gem clip 25 mm , Colin , Correction fluid pen type , Duster cloth white , Duster Cloth Yellow , DVD Rewriteable , Black DVD recordable , Envelope cloth size A4 Green , Envelope cloth size legal green , Envelope size 11 inch x 5 inch green , Envelope size 12 inch x 10 inch green , Envelope size 12 inch x 5 inch green , Envelope size 10.5 inch x 4.5 inch green , Envelope size 9 inch x 4 inch brown , Envelope size 16 inch x 6 inch brown , Envelope size 16 inch x 6 inch green , Envelope size 6 inch x 5 inch green , Envelope 16 inch x 12 inch with cloth green , Envelope 18 inch x 14 inch with cloth green , Envelope for DO letters , Eraser non dust big apsara pack of 10 Nos , Executive bond paper 90 GSM A4 size , Fevistick 15 gms , Fevicol 100 gms , File cover white duly printed office name and logo , File cover white , File cover duly printed office name and logo , L Folder , Gem clip plastic , Hand book plain as per sample , Highlighter pen five colour in each set , Mouse pad , OHP Permanent marker all colour , Paper pin T type head box , Fax roll for Panasonic machine , Steel paper cutter blade 1 inch , Steel paper cutter 1 inch , Paper punch HDP 1320 , Parcel cloth Khadi white , Sticky pad size 1.5 x 2 inch 3 colours florescent , Paper weight , Sticky pad size 3 x 3 inch , Sticky pad size 4 x 4 inch , Pen Cello flair blue 10 Nos in a packet , Pen Cello flair Black 10 Nos in a packet , Pen Cello flair Red 10 Nos in a packet , Pen add gel blue , Pen add gel black , Pen add gel red , Pen pilot V7 black , Pen pilot V7 blue , Pen pilot V7 red , Pen pilot V7 green , Pen butter flow ball pen 10 Nos in a packet , Pen white board marker black , Pen white board marker Blue , Pen white board marker Red , Pen stand for Officers , Pen stand , Pencil apsara HB , Pencil drawing B Platinum , Battery AAA 1.5V , Battery AA 1.5V , Pencil sharpener as per sample , Pencil sharpener table fixed large , Pin stapler 24 x 6mm , Pin stapler 10mm , Plotter paper 36 inch x 91cm x 100 mtr , Pocha cloth with mob stick scortch brite , Plotter paper 36 inch x 91 cm x 50 mtr , Plotter tracing paper 36 inch x 91 cm x 150 mtr , Poker wooden handle , Refill add gel pen blue , Refill add gel pen black , Register 1 QR ruled as per sample , Register 2 QR ruled as per sample , Register 3 QR ruled as per sample , Register 4 QR ruled as per sample , Register 5 QR ruled as per sample , Room Freshener , Rotaring pen 0.30mm , Rotaring pen ink , Steel scale 12 inches , Scissor big 6 inches , Scissor big 12 inches , Sketch pen set assorted colour , Stamp Pad , Stapler HD 45 Big , Stapler No 10 small , Spiral Roll all size , Stapler large size DS 12s 17 , Stick folder file A4 , Tag white cotton large , Tag best quality nylon large , Tag small , Towel for revolving chair big , Tracing paper size A3 , Tracing paper size A4 , Tray Medium size , Twine jute Nylon , Wall clock , Photocopier Paper A3 size 80 GSM , Photocopier Paper A4 size 80 GSM , Photocopier Paper Legal size 80 GSM

Details: Name of Work OFC cable laying for Electrical Power distribution SCADA network, Control and Signal cable wiring in Electrical panels in IGCAR, Kalpakkam Note : 1.This schedule must be read along with the drawing, Specification and scope of work (Section V) and General Specifications (Section VI) for complete interpretation of this scope of work quantitywise. 2.Items of work described in brief below are detailed under Specification of Work. The scope of work will not be estimated from the brief description of this schedule. 3.Rate quoted must include all components required for meeting the specification and performance requirements of the item irrespective of whether they are specifically brought out in this Schedule or not. 4.Tenderers are advised to get acquainted with the site conditions before quoting. 5.Schedule Rate Shall be firm and Overall Conditional Discount for the Total Tendered amount will not be accepted. 6. Rate Quoted Should be inclusive of all taxes including GST.

Details: Description:- 21.1providingandfixingaluminiumworkfordoors,windows,ventilatorsand partitionswithextrudedbuiltupstandardtubularsections/appropriatezsectionsandother sections Of Approved Make Conforming To Is: 733 And Is: 1285, Fixing With Dash Fasteners Of Required dia And Size, Including Necessary Filling Up The Gaps At Junctions, I.e. At Top, Bottom And Sides With required Epdm Rubber / Neoprene Gasket Etc. Aluminium Sections Shall Be Smooth, Rust Free, Straight, mitred And Jointed Mechanically Wherever Required Including Cleat Angle, Aluminium Snap Beading for Glazing / Paneling, C.p. Brass / Stainless Steel Screws, All Complete As Per Architectural Drawings andthedirectionsofengineer-in-charge.(glazing,panelinganddashfastenerstobepaidfor separately) : 21.1.1 For Fixed Portion 21.1.1.1 Anodised Aluminium (anodised Transparent Or Dyed To required Shade According To Is: 1868, Minimum Anodic Coating Of Grade Ac 15)

Details: ON TURN KEY BASIS Construction of BAKHTUNI TANK PROJECT, in Manasa block of District Neemuch consisting of approximately 345 m long earthen dam and all its components with excavation & construction of Head sluice, Spill & Approach channel, Waste Weir under Unit-I Head work along with excavation, earthwork & lining of Main canal RD 0 to 2100 m and all necessary relevant structures to irrigate 300 Ha. CCA. This activity also Include survey & investigation, geological Investigation, preparation & submission of LA. Cases for Pvt. /Govt./forest land, design, drawing. estimation, DPR submission and its approval from competent authority for both Head work & canal system of BAKHTUNI TANK PROJECT, including maintenance & defect liability period of two years from date of issue of completion certificate.