Brahmaputra Board Tender

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed. (I) In Sub-Structure upto plinth level inc;luding dewatering if necessary (b) In Proportion 1:4

Plain cement concrite works with coarse aggregate of size 13mm to 32mm foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately) (a) In prop 1cement: 3sand: 6coarse aggregate by volume

Earth/sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary (c) with river sand or silt (predominantly non plastic) by bick carriage including loading and unloading.

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinfor cement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) (I) Using Mixer Machine (A) In substructure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, insptic tank,inspection pit and other works not less than 100mm thik up to plinth level. (N) Without using admixture, plasticiser (b) M20 grade concrete or Prop. 1:1:5:3

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in:Foundation, footing, bases of column, pile cap, raft and mass concrete works etc.(b) Using 25mm thick plank

Providing poloshed SUNROCK-HI CTS/MULTIWYN tiles of approved quality, size, shape and less than 18mm on floors and skirtings over cement morter bed 10mm thick in prop. 1:3 (1cement; 3coarse sand) including cutting where necessary finisged with flush pointing with fix-A-Tile (Choksey/Sika /pedelite/Rouf)/white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department (a) SUNROCKHi CTS TILES (i) well, chocolate, diamond square, ramp,beach sand (300x300)mm

18mm thick marble stone tiles in flooring including riser and treads of steps, skirting, dado, walls, pillars laid with 10mm thick base of cement plaster in prop. 1;3 ( 1 cement:3 coarse sand) and jointed with grey cement slurry includding rubbing and poishing complete with marble tiles of specified qualityand shade at all levels. 18mm thick marble stone tiles in flooring including risers and treads of steps, skirting, dado, walls, pillars laid with 10mm thick base of cement plaster in prop 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry including rubbing and polishing complete with maerble tiles of spwcified quality and shade at all levels. (a) with 18mm thick marble stone tiles of size 600mm x 600mm (i) dungri slab

Applying primary coat over new steel and other metal surface up to 100m in width or girth after [reparing the surface by throughly cleaning oil, grease, dirt and other foreign matter and scoured with wire brushes, fine steels, wood scrapers and sand paper. (a) with ready mixed ''red-lead/ red oxide'' primer.

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J&N paint Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter.(i) Surface upto 100mm in width or girth (b) high gloss (Asian paint/ berger paint/ ICI paint/J&N paint/ nerolic)

1st class brick nogged wall in cement morter including racking out joint and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/tor steel of column to be embeded in cement mortar and will be measured and paid separately) (A) 112mm thick brick wall (a) In cement morter in proportion 1:4 (1 cement :4 sand)

15mm thick cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. (A) on rough side (b)In cement mortar 1:4

15mm thick cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. (B) on fair side (b) In cement mortar 1:4

Supplying fitting and fixing chain link fencing of 10 S.W.G., G.I. Wire 50mmx50mm mesh fitted to M.S. angle iron post at 2000mm apart of specification detailed below including supplying, fitting and fixing hooks, eye bolts with nuts, staples and bolts including three horizontal lines of G.I. wire 10 S.W.G. at top, middle and bottom and with one vertical line to each fencing post for keeping the fencing tight and erect complete, including one coat of primer painting to M.S. angle iron post in P.C.C. base etc. with following-a) Corner and end posts with M.S. angle of size 50mmx50mmx5mm and length not less than 1800mm only duly slotted and bottom torqued with two numbers as stay posts.b) Intermediate post with M.S. angle of size 40mmx40mmx5mm and length not less than 1800mm only duly slotted and bottom torqued and splayed.c) Stay post with M.S. angle of size 35mmx35mmx5mm and length not less than 1800mm duly slotted and bottom torqued and splayed. All M.S. angle iron posts are to be fitted to P.C.C. base embeded not less than 600mm (P.C.C. work shall be measured and paid separately).

Supplying of Bleching powder

Supplying Lime

Supplying Alum etc.

Video graphy and still photo graph before execution, during execution and after completion of work

Supplying and Installation Plastic Dustbin (Sintax GBR 100) with M.S. Stand