Public Works Department Tender

Car Door: Stainless Steel centre opening automatic door provided with V3F controlled door drive system. Landing Door: Stainless steel centre opening automatic door provided with V3F controlled door drive system Door Opening: Automatic power oprated door with full length Photocell assembly light curtain sensor. Car operating panel : A best quality Screen touch car operating panel with floor indication and digital hall position & direction indicatiors. Landing operating panel: A best quality Screen touch car operating panel with floor indication and digital hall position & direction indicatiors. Fire Rated Door : 2 Hours

ARD: Automatic rescue device complete with dry maintenance free batteries as required for automatic evacuation to the nearest floor in case of power failure / single phasing/others. Overload Protection: Fully loaded with overload protection.On overloading the lift car will not start with door remaining open and give audio display indication. Emergency lighting in car: Battery operated emergency lighting in the lift car. Intercom system: Battery operated intercom system in Lift Car, Machine Room & Control Room. Emergency Alarm: Battery operated alarm bell system in lift car and control room. Fireman switch: Fireman switch at main landing terminal. Voice Synthesizer: Voice announcement system (Voice Synthesizer) in the car to announce the position of the elevator in the hoist way as the car passes or stops at a floor served by the elevator. Main rope - Belt Type (Flat Coated steel belt with V groove / Sreel rope)

Communication & Monitoring the Lift: Lift controller/ Panel shall be Ethernet/Modbus ready with necessary converter, DC Power supply module etc. if required, and there shuld be single Ethernet/Modbus output from the Controller/panel and the same should be connected to BMS (Building Management System) and the controller/ panel should have also required for monitoring of real time data with date & time, maintenance-call back record, Mantrap notice, call records, location of car, Lift room temperature etc. should be noticed & display to in any desktop & mobile though wireless system.

Other works: Necessary cutting of wall/floor for fixing the Fire Alarm switch, all Button switch and also making provision to entry of rope, electric wire etc. as required to complete the job.

DIMENSION OF SHAFT & POWER SUPPLY Available Shaft Dimension: 1950(W) mm X 2025(D)mm (Bidder should visit the site) Pit Depth : 1600 mm (Bidder should visit the site) Overhead : 4500 mm (Bidder should visit the site)

Electric power supply: AC 415 Volt 3phase, 50 Hz, terminated in machine room as per IS

SITC of Automatic Lift ( as per manufacturer design & as per detailed specification below conforming to IS ) and putting into operation after final testing in the existing lift shaft complete with all accessories and repairing the damage wall / floor if any etc to complete as reqd.

Make : OTIS / KONE/SCHINDLER Type: passenger Lift . Load : 16 Passenger / 1088 Kg Control: Microprocessor based with AC variable voltage & variable frequency ( VVVF) Machine:- Energy efficient machine, Gearless, Without Machine Room. Position of Machine Room: Directly above the lift Speed: 1 Mtrs./ Sec Floor served: B+G+7 Landing: 9, all on same side Total Rise : 32 Mtr (Approx) (Bidder should visit the site)

Operation: Microprocessor based implex full collective with or without attendant. Signals: Digital car position indicator,car travels direction indicator in car & at all landing with call registration indicator. Leveling accuracy: ±5 mm(Micro levelling arrangement.

CAR Car inside : 1000 mm ( W ) x 2400 mm ( D ) x 2300 mm (H) or As per manufacturer's standard conforming to IS. Car Entrance : Clear Opening 900 mm (W) x 2000 mm/ 2100mm (H ) protected with car door Car Enclosure: Stainless Steel sheet (20 SWG) with Hairline finish with hand rail. Car Ceiling & Lighting: Stainless Steel with hairline finish with LED lighting and Fan Car Ventilation: Pressure fan with anodised aluminium grill. Car Flooring : Decorative granite flooring (As per direcion of EIC and according to this Department's Order).

Car Door: Stainless Steel centre opening automatic door provided with V3F controlled door drive system Landing Door: Stainless steel centre opening automatic door provided with V3F controlled door drive system Door Opening: Automatic power oprated door with full length Photocell assembly light curtain sensor Car operating panel : A best quality Screen touch car operating panel with floor indication and digital hall position & direction indicatiors. Landing operating panel : A best quality Screen touch car operating panel with floor indication and digital hall position & direction indicatiors. Fire Rated Door : 2 Hours

PROTECTIVE DEVICES & OTHER ACESSORIES ARD: Automatic rescue device complete with dry maintenance free batteries as required.for automatic evacuation to the nearest floor in case of power failure / single phasing/others. Overload Protection: Fully loaded with overload protection.On overloading the lift car will not start with door remaining open and give audio display indication Emergency lighting in car: Battery operated emergency lighting in the lift car. Intercom system: Battery operated intercom system in Lift Car, Machine Room & Control Room Emergency Alarm: Battery operated alarm bell system in lift car and control room Fireman switch: Fireman switch at main landing terminal. Voice Synthesizer: Voice announcement system (Voice Synthesizer) in the car to announce the position of the elevator in the hoist way as the car passes or stops at a floor served by the elevator. Main rope - Belt Type (Flat Coated steel belt with V groove / Sreel rope)

Communication & Monitoring the Lift : Lift controller/ Panel shall be Ethernet/Modbus ready with necessary converter, DC Power supply module etc. if required, and there shuld be single Ethernet/Modbus output from the Controller/panel and the same should be connected to BMS (Building Management System) and the controller/ panel should have also required for monitoring of real time data with date & time, maintenance-call back record, Mantrap notice, call records, location of car, Lift room temperature etc. should be noticed & display to in any desktop & mobile though wireless system.

Other works: Necessary cutting of wall/floor for fixing the Fire Alarm switch, all Button switch and also making provision to entry of rope, electric wire etc. as required to complete the job.

DIMENSION OF SHAFT & POWER SUPPLY "Available Shaft Dimension: 1925(W) mm X 3050(D) mm (Bidder should visit the site)" Pit Depth : 1600 mm (Bidder should visit the site) Overhead : 4500 mm (Bidder should visit the site)

Electric power supply: AC 415 Volt 3phase, 50 Hz, terminated in machine room as per IS

SITC of Automatic Lift ( as per manufacturer design & as per detailed specification below conforming to IS ) and putting into operation after final testing in the existing lift shaft complete with all accessories and repairing the damage wall / floor if any etc to complete as reqd.

Make : OTIS / KONE/SCHINDLER Type: Passenger Lift . Load : 13 Passenger / 1088 Kg Control: Microprocessor based with AC variable voltage & variable frequency (VVVF) Machine:- Energy efficient machine, Gearless, Without Machine Room Position of Machine Room: Directly above the lift Speed: 1 Mtrs./ Sec Floor served: B+G+7 Landing: 9, all on same side Total Rise : 32 Mtr (Approx) (Bidder should visit the site) Operation: Microprocessor based implex full collective with or without attendant. Signals: Digital car position indicator,car travels direction indicator in car & at all landing with call registration indicator. Leveling accuracy: ±5 mm(Micro levelling arrangement)

CAR Car inside : 1000 mm ( W ) x 2000 mm ( D ) x 2300 mm (H) or As per manufacturer's standard conforming to IS. Car Entrance : Clear Opening 800 mm (W) x 2000 mm/ 2100mm (H ) protected with car door Car Enclosure: Stainless Steel sheet (20 SWG) with Hairline finish with hand rail. Car Ceiling & Lighting: Stainless Steel with hairline finish with LED lighting and Fan. Car Ventilation: Pressure fan with anodised aluminium grill. Car Flooring : Decorative granite flooring (As per direcion of EIC and according to this Department's Order).

Car Door: Stainless Steel centre opening automatic door provided with V3F controlled door drive system. Landing Door: Stainless steel centre opening automatic door provided with V3F controlled door drive system. Door Opening: Automatic power oprated door with full length Photocell assembly light curtain sensor. Car operating panel : A best quality Screen touch car operating panel with floor indication and digital hall position & direction indicatiors. Landing operating panel : A best quality Screen touch car operating panel with floor indication and digital hall position & direction indicatiors. Fire Rated Door : 2 Hours.

PROTECTIVE DEVICES & OTHER ACESSORIES ARD: Automatic rescue device complete with dry maintenance free batteries as required.for automatic evacuation to the nearest floor in case of power failure / single phasing/others. Overload Protection: Fully loaded with overload protection.On overloading the lift car will not start with door remaining open and give audio display indication Emergency lighting in car: Battery operated emergency lighting in the lift car. Intercom system: Battery operated intercom system in Lift Car, Machine Room & Control Room Emergency Alarm: Battery operated alarm bell system in lift car and control room Fireman switch: Fireman switch at main landing terminal. Voice Synthesizer: Voice announcement system (Voice Synthesizer) in the car to announce the position of the elevator in the hoist way as the car passes or stops at a floor served by the elevator. Main rope - Belt Type (Flat Coated steel belt with V groove / Sreel rope)

Communication & Monitoring the Lift : Lift controller/ Panel shall be Ethernet/Modbus ready with necessary converter, DC Power supply module etc. if required, and there shuld be single Ethernet/Modbus output from the Controller/panel and the same should be connected to BMS (Building Management System) and the controller/ panel should have also required for monitoring of real time data with date & time, maintenance-call back record, Mantrap notice, call records, location of car, Lift room temperature etc. should be noticed & display to in any desktop & mobile though wireless system.

Other works: Necessary cutting of wall/floor for fixing the Fire Alarm switch, all Button switch and also making provision to entry of rope, electric wire etc. as required to complete the job.

DIMENSION OF SHAFT & POWER SUPPLY "Available Shaft Dimension: 2000(W) mm X 2700(D) mm (Bidder should visit the site)" Pit Depth : 1600 mm (Bidder should visit the site) Overhead : 4500 mm (Bidder should visit the site)

Electric power supply: AC 415 Volt 3phase, 50 Hz, terminated in machine room as per IS

Terms & Condition i) The Agency must procure the materials from the Manufacturer / OEM or from their authorised sales channel so that the standard warranty / support of the Manufacturer / OEM becomes applicable to the products to be delivered and installed by them.

ii) Documents that authenticates such procurement from the Manufacturer / OEM or from their authorized sales channel and standard warranty / support should be sent from the e-mail of the Manufacturer / OEM / authorized sales channel to the e-mail of Engineer-in-Charge and hard copy of it to be submitted during execution, of work/submission of bill.

iii) The rate quoted by the manufacturer should be inclusive of all taxes and duties and for providing 2 years DLP after completion of 1 year of initial commisioning.

iv) Rates should be quoted with minor civil works, wall cutting and mending good the damages to the original finish.