Gorkhaland Territorial Administration Tender

PWD(WB)/BUILDING WORKS(CCS)/Page-34/Item-22II (II) Cement concrete with 30 mm. down graded shingles excluding shuttering.N.B. VarietyIn ground floor . (a) 1:3:6 proportion.

PWD(WB)/BUILDING WORKS(CCS)/Page-24/Item-4 Ordinary cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttring and reinforcement, if any, in ground floor as per relevant IS codes. (b) River bazree.

PWD(WB)/BUILDING WORKS(CCS)/Page-43/Item-40 Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at inter-section, complete as per drawing and direction. (a) For works in foundation, basement and up to roof of ground floor/up to 4m. Tor steel/Mild steel. other than SAIL/TATA/RINL/JSW/JSPL/Shyam/SRMB/ISSL/BMASL/Electrosteel

PWD(WB)/BUILDING WORKS(CCS)/Page-42/Item-36 Hire and labour charge for shuttering with centreing and necessary staging up to 4 m. using approved stout props and thick hard wood planks of approved thick ness with required bracing for concrete slabs, beams, columns, lintels curved or staight including fitting fixing and striking out after complection of works. (up to roof of ground floor). (a) 25 mm. to 30 mm. thick wooden shuttering as per decision & direction of the Engineer-in-charge. .

PWD(WB)/BUILDING WORKS(CCS)/Page-16/Item-16 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor.

PWD(WB)/BUILDING WORKS(CCS)/Page-189/Item-1 Plaster ( to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering conrners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (ground floor). [Excluding cost of chipping over concrete surface]. (ii) With 1:4 cement mortar . (b) 15 mm. thick plaster.

PWD(WB)/BUILDING WORKS(CCS)/Page-115/Item-4 Supplying, Fitting & Fixing Factory made P.V.C. door frame of size 50 mmx47mm with a wall thickness of 5 mm, made out of extruded 5 mm, PVC sheet mitercut at two corners and joined with two nos of 1.5 mm long brackets of 15 mm x15mm M.S. square tube. The two vertical door profiles are to be reinforced with 19mmx 19 mm M.S. Square tube of 19 gauge, weather seal to be provided throughout the frame. The door frame shall be fixed with the wall using 65/100 mm longM.S. Screws through the frame by using P.V.C fasteners. A minimum of 4 Nos ofscrews to be provided for each vertical member and minimum 2 Nos forhorizontal member etc. complete as per Manufacturer‟s specification anddirection of Engineer-in-Charge.

PWD(WB)/BUILDING WORKS(CCS)/Page-125/Item-15 Supplying, Fitting & Fixing 30 mm thick Factory made solid Panel PVC DoorShutter consisting of outer frame made out of M.S. tubes of 19 gauge thicknessand size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have costof steel primers of approved make and manufacture, M.S. frame covered with 5mm th. heat moulded PVC “C” channel of size 30 mm th, 70 mm width out ofwhich 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle oneither sides forming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top &bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, bottom and lock railsshall be provided either side of the panel with 10 mm (5 mmx2) th.,20 mm widecross PVC sheet as gap insert for top rail and bottom rail. Paneling of 5 mm th.both side PVC sheet to be fitted in the M.S. frame welded/sealed to the style s&rails with 7 mm (5 mm+2 mm) th.x15 mm wide PVC sheet beading on inner sideand joined together with solvent cement adhesive. An additional 5 mm th. PVCstrip of 20 mm which is to be stuck on the interior side of the “C” channel usingPVC solvent adhesive etc. complete excluding all necessary hardwares as perdirection of Engineer-in-Charge.In ground floor.

PWD(WB)/BUILDING WORKS(CCS)/Page-200/Item-2 (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand parpering etc. in cluding using of approved putty etc. on the surface , if necessary. (a) On timber or plastered surface: (1) With super gloss (hi-gloss). (iv) Two coats (with any shade except white).

PWD(WB)/SANITARY AND PLUMBING WORKS/Page-29/Item-1 Supplying, fitting and fixing CPVC (Chlorinated PolyvinylChloride) pipes of approved make conforming to IS-15778:2007 . with all necessary accessories, specials viz. socket,bend, tee, union, cross, elbo, nipple, longscrew, reducingsocket, reducing tee, short piece etc. fitted with holder batsclamps, including cutting pipes, fitting, fixing etc. completein all respect including cost of all necessary fittings asrequired,jointing materials in any position above ground.(Payment will be made on the centre line measurements oftotal pipe line including all specials. No separate paymentwill be made for accesories, specials.(a) For Exposed Work For exposed work (i) CPVC Pipes Class-I,SDR-11 15 mm dia.

PWD(WB)/SANITARY AND PLUMBING WORKS/Page-60/Item-1 Supplying, fitting & fixing Cast iron soil pipe only conforming to I.S.3989/1970 and I.S.1729/1964 with bobbins, nails etc. including making holes in the wall, floor etc. and cutting trenches etc. in any floor through masonry conctrete, if necessary, and mending good damges with necessary jointing materials and painting two coats to the exposed surface with approved paint complete. (Measurement will be made along the enter line of the total pipe line in fitted condition including specials, payment for specials & painting will however be paid seperately). With valamoid joint including sealing the top with cement mortar (4:1). Upto quarter depth. 100 mm dia (internal).

PWD(WB)/SANITARY AND PLUMBING WORKS/Page-79/Item-4 Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding 'P' or 'S' trap (excluding cost of concrete for fixing). 530 mm X 410 mm.

PWD(WB)/SANITARY AND PLUMBING WORKS/Page-37/Item-6 Supplying PVC water storage tank of approved quality with closed top weith lid (Black) - Multilayer. 500 litre capacity.

PWD(WB)/SANITARY AND PLUMBING WORKS/Page-10/Item-16 Supplying, fitting and fixing G.I gravity operated water tap for public use with pilfer proof arrangement of approved brand and make. 15 mm dia.

PWD(WB)/SANITARY AND PLUMBING WORKS/Page-41/Item-1 Wash basin white vitreous china of approved make (without fittings) supplied, fitted and fixed in position on 75mm X 75mm X 75mm wood blocks and C.I. Brackets including two coats of painting of C.I. Brackets. 450 mm x 300 mm size.

Construction of Septic Tank Lump sum