Eastern Railway Tender

Quick cutting with abrasive rail cutter of all types of rail sections including wear resistant, head 4 hardened rails up to 110 UTS, with contractors tools & plants, equipment, consumable with all lead & lift etc. complete as directed by Engineer in-charge. Abrasive Rail Cutter will be as per RDSO Specification No. TM/SM/1 (Rev. 01 of 2012) with latest status of RDSO; Rail Cutting Wheel Abrasive Disc will be as per RDSO Specification No.TM/SM/2 (Rev. 01 of 2020)

Drilling of hole of different diameter and chamfering, in rail of any section and any UTS manually only in emergencies with contractor's labours, tools & plants, consumables etc.

25mm gap 'in-situ' welding during traffic block using Railway's welding portion and finishing of weld to meet the prescribed tolerances and pass all stipulated tests with all required labour, materials, consumables, tools, equipments etc. to complete the work in all respect as per IR's ""Manual for Fusion Welding of Rails by Alumino - Thermic Process"" with latest correction slips, including marking of welded joint, painting weld collar with 7 anticorrosive paint, restoration of track near weld joint to original position and fixing of joggled fish plate at new weld, to be removed after passing of weld in USFD test as directed by Engineer in charge.Note:1. Welding portion and related accessories as per Annexure - I shall be supplied by Railways. All other items required shall be supplied by the Contractor.2. Welding shall be carried out only by trained welder having valid competency certificate. 3. Hydraulic Weld trimmer shall be used for chipping and profile Grinder for finishing.4. Required nos. of Joggled fish plates shall be supplied by Railway at nearest P. Way Stores and the same shall be returned at nearest P. Way Store or at other location as per direction of Engineer-in-Charge after release from track

Lubrication of fish plated rail joints under traffic, by using Grease Graphite Grade 'O' (IS:408) and 8 Black oil supplied by contractor, for all types of rail sections as per procedure laid down in latest version of IRPWM and as directed by Engineer In charge. Note: Release U/S bolt & nuts is to be deposited back. If any fish bolts is jammed it should be cut with chisel and hammer and replaced with fresh fish bolt supplied. For 1.00m long fishplates

Through packing of track, as per procedure prescribed in latest edition of Indian Railways Permanent Way Manual For PSC sleeper Track with Sleeper Density of 1540 Sleepers/Km or more

Through replacement of Grooved Rubber Sole pads(GRSP) on PSC sleepers duly removing the ERCs and liners and replacing the GRSP by just lifting the rail after cleaning the rail seat, refixing the liner and 10 ERC after greasing of ERCs, liners and Liner contact area including sealing with Contractor's Grease Graphite Grade 'O' (IS:408) duly cleaning of rust/scale of ERC, Metal /GFN liners & SGCI insert by using wire brush, scrapper/sand emery paper etc., with all contractor's labour, tools, plants including collection and stacking of released materials at nominated locations within SSE Jurisdiction and as directed by Engineer-in-Charge. Note: GRSP will be supplied at SSE/stores/depot.

"Anti-corrosive painting of rail outside track on rail bottom, web, foot and fishing plane with two coats of thickness of 100 microns each by bituminous black paint confirms to IS-9862 of reputed make including surface preparation, as a complete job as per procedure prescribed in latest edition of IRPWM."

""Anti-corrosive painting of rail on running track of any sleeper density on web, foot etc. including 12 liner contact area (excluding bottom of foot) and fishing plane as per requirement with two coats of thickness of 100 microns each by bituminous black paint confirms to IS-9862 of reputed make including painting of liners, ERCs and including surface preparation, as a complete job as per procedure prescribed in latest edition of IRPWM Note: 60% of payment shall be made if painting on only gauge face side is done. "

Anti-corrosive painting to weld collar for Thermit welded rail joints on track or on cess for new welded joints to protect against normal corrosion for any rail section with two coats of ready mixed bituminous 13 black paint of reputed make confirming to latest IS:9862 on welded area up to 10cm on either side including on the underside of rail foot by brush including surface preparation as per Railway's AT Weld Manual including lettering / weld numbering with approved enamel paint as directed Note: Before painting, dust, loose rust and mill scale and dirt shall be removed thoroughly by wire brushing. Scrubbing welded area with water to make it free from slag and other water soluble compounds to make it dry.

Boxing and profiling of ballast as per procedure prescribed in latest edition of IRPWM including 14 cess dressing on both sides of track. The work will include removing excess ballast from track and putting the same in crib and shoulder by leading to a maximum of 50m including crossing of track, deweeding on ballast section etc and as directed by Engineer-In charge.

Fixing Joggled Fish Plates with bolt / clamp (supplied by Railway from nearest SSE Store) in running track conditions at welds on rail, as directed by engineer in-charge (drilling of holes in rail, if required, shall be paid separately).

Removing seized ERC from SGCI inserts of existing track by using suitable approved chemicals 16 and re-fixing after greasing of insert eye and ERC with Contractor's grease of specified quality as per provisions of IRPWM, as directed by Engineer in-charge. Note: 1.List of Seized ERC along with location shall be prepared after inspection of SSE/P.Way and marked prior to execution of this item. 2. Due care shall be taken to avoid any damage to the sleeper 3.A penalty of 50% of the basic cost of new sleeper in nearest sleeper factory shall be levied on each, if SGCI insert is broken or sleeper gets cracked in the process.

"Loading, leading and unloading of all types of P.Way fittings and all other miscellaneous material except Rails, sleepers, switches, crossings, SEJs and Glued Joints by road vehicles for different leads.Note: Lead shall be the shortest motorable road length between the points of loading and unloading. "

Transportation of Rails, sleepers, switches, crossings, SEJs and Glued Joints by road vehicles for different leads.Note: 1. Lead shall be the shortest motorable road length between the points of loading and unloading.2. Loading and unloading shall be paid extra under relevant items.

Fabrication of INSITU glued insulated joints for 52kg/60 kg rails as per RDSO approved drawing no.5361 and 5843 respectively and conforming to manual for glued insulated rail joints, 1998 issued by Ministry of Railway, RDSO/LKO and in accordance with the process sheet of E. Rlys/PD/MGS dated 04.11.98 with supply of all fittings and accessories such as:- i) 950 mm long fish plate, ii) HTS bolts & nuts, iii) Punched washer, iv) Insulated bushes, v) Insulated channels, vi) 10/6 mm thick end post, vii) Araldite, viii) Hardener, ix) Glass cloth 2 carrier and all other materials & fixtures for cleaning & assembling excluding rails complete in all respect. Fabrication of INSITU glued insulated joints for 52kg/60 kg rails as per RDSO approved drawing no.5361 and 5843 respectively and conforming to manual for glued insulated rail joints, 1998 issued by Ministry of Railway, RDSO/LKO and in accordance with the process sheet of E. Rlys/PD/MGS dated 04.11.98 with supply of all fittings and accessories such as:- i) 950 mm long fish plate, ii) HTS bolts & nuts, iii) Punched washer, iv) Insulated bushes, v) Insulated channels, vi) 10/6 mm thick end post, vii) Araldite, viii) Hardener, ix) Glass cloth carrier and all other materials & fixtures for cleaning & assembling excluding rails complete in all respect.

Making & Erection of creep post for SEJ/Curves etc including cutting and painting of rails as per direction of engineer in-charge. Rail will be supplied by Railway. The rate includes the cutting of rails, transportation up to site within one KM, excavation of earth, cost of paint, all labour, tools & plants etc.

GST @ 18 % on Sch-B (NS Items)