Uttarakhand Power Corporation Limited Tender

11 KV 90 KN Tension Clamp with Bail and IPC (Section Pole)

11 KV Cable Ties on every Pin Insulator

11 KV IPC for CC to CC Connection in every Section Pole

11 KV IPC for CC to Bare Connection at both end and tapping

11 KV Mid Span Jointing Kit at every 500 mt. Cable Drum

Bimetalic Crimping Lugs (Preinsulated)

IPC with Aluminium Bail for Earthing 1 No./2.5 Km.

Supply of Holding Clamp for SP 55 with Nut & Bolts

Total (A)

Labour (B)

Cartage of following Poles from Store Centre to Nearest Road Site with Loading/Unloading at both points & proper staking (Loading, Unloading & Carriage per pole) (0-20 Km.)

ST Pole SP 55

Cartage of Other Material by Vehicle from Store Centre to Nearest Road Site with Loading/Unloading at both points (0-20 Km.)

Head Load Cartage of following Poles from Road Site to Construction Site (Rates are per Pole/Km, including Loading/Unloading at both points) (0-1 Km.)

ST Pole SP 55

Head Load Cartage of Small Material by Vehicle from Store Centre to Nearest Road Site including Loading & Unloading at both points (0-1 Km.)

Excavation of Earth for Pole Pit of Size 0.9x0.6x1/6 of Full Length of Pole for Erection of Pole in all type of Soil including Proper Dressing of Sides and Ramming of Bottom including getting out the Excavated Soil and Disposal of Surplus Excavated Soil as directed, Complete Work

Grouting of Pole in size 0.45x0.45x1/9 of the support in CC ratio 1:4:8 (1 cement : 4 graded stone 20mm nominal size : 8 coarse sand) block including cost of cement, sand and stone ballast, back filling of soil and boulders in pit and ramming and proper alignment & leveling (As Per RESSPO Construction Manual)

Erection of following Single Support Pole in Proper Level and Alignment alongwith Fixing of all Accessories

STP SP 55

Muffing of Poles Size 0.45cmx0.60cm radious with CC 1:3:6 (1 cement : 3 coarsend : 6 graded stone 10mm nominal size) Block Size, 45 cm Height from Ground Level including cost of Cement, Sand & Stone etc.

Painting of Poles with Angle & Channel and all Steel Part by One Coat of Red Oxide Primer and Two Coats of Aluminium Paint and Two Strip of Fluorescent Alternate Red and white Paint 30 Cm. Wide upto 1.5 Mtrs. from Ground Level

Fabrication of M.S. Channel & Angle

Removing of Old Rabbit/Weasel Conductor with Opening of Existing Jumpering and Making of Bundle with Carriage from Pit Site to Store including Loading/Unloading, Complete Work

Laying, Spreading, Stringing and Sagging of 11 KV Line ACS AL 59 (104.98 Sqmm) Covered Conductor in 3 Phase of the following Wire as Phase Wire including Proper Sagging with Binding and Jumpering as per user Manual and Sagging Chart (inclusive of cartage and head load Cartage at work site). Rollers of the appropriate diameter and quantity have to be provided for installation. The roller shall have a smooth clean surface, no sharp edges and shall rotate easily to prevent the covering from damage any abrasive contact with soil or stone is not permitted, abrasive contact of the covering with branches or similar shall be avoided. Covered conductor shall be pulled by using appropriate pulling devices ensuring that the pulling force is distributed to the conductor recommendation given in EN-50397-3 should be followed for storage transport and installation of covered conductor.

Looping and Chooping of Tree Branches for Route Clearence

Fixing of MVCC Accessories

11 KV 90 KN Tension Clamp with Bail and IPC (Section Pole)

11 KV Suspension Ties on every Pin Insulator

11 KV IPC for CC to CC Connection in every Section Pole

11 KV IPC for CC to Bare Connection at both end and tapping

11 KV Mid Span Jointing Kit at every 500 mt. Cable Drum

Bimetalic Crimping Lugs (Preinsulated)

IPC with Aluminium Bail for Earthing 1 No./2.5 Km.

Total (B)

Sub Total (A+B)