Uttar Pradesh Rural Road Development Agency Tender

Providing, laying, spreading and compacting stone aggregates of specific sizes (53-22.4 mm) to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per Technical Specification Clause 405. (WBM III)

Construction of Panel concrete plain Cement concrete pavement, Thickness as per design, over a prepared subbasewith 43 grade cement or any other type as per Clause 1501.2.2 M 30 (Grade) coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate no exceeding 25mm, mixed in a concrete mixer of not less that 0.2 cum capacity and appropriate weigh batcher uusing approved mix design , laid in approved fixed side formwork ( Steel Channel, Laying and fixing of 125 micron thiock polythene film , wedges, steel plates including levelling th formwork as per Drawing ), Spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and fininshedin continous operation including provision of contraction and expansion, construction joints , applying debonding strips, primer, sealant , near approaches to bridge/culvert and construction joints, admixture as approved, curing of concrete slabs for 14 days. curing compound ( Where specified ) and water finishing to lines and grade as per drawing and Technical specification Clause 1501. PCc Grade M-30 Each Panesl ( 0.50 X0.50 ) thickness 125mm

Providing and fixing of reflective typical PMGSY logo and informatory sign board with a corrosion resitant 3mm and 4mm thick aluminum composite panel face to be fully covered with DM 5600 engineering grade prismatic / equvivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle

Providing and fixing of reflective Citizen information sign board A and B with a corrosion resitant 4mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle

Providing and fixing of Maintenance information sign board with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle

Providing and fixing of Logo sign board A and B at starting point & Intermediate distance with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle

Providing and fixing of semi reflective curvature board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads and approved drawing Clause 1701.2.2. (0.27 sqm area)

Providing and fixing of semi reflective Village Sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads and approved drawing Clause 1701.2.2. (0.27 sqm area)

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. Ordinary Kilometer Stone (Precast)

Reinforced cement concrete M15 grade hectometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. 200 m Stone (Precast)

Maintenance of road signs by way of cleaning and repainting of mandatory / requlatory / cautionary / informatory and place identifications sign board as perdrawings and technical specification Clause 1910

Maintenance of 200 metre km stone by way of refiting of tilted stones repairing with cement mortar, cleaning, repairing and lettering on 200 metre km stone and 5th km stone as per drawing and technical specification Clause 1912

Providing and laying stone set pavement on prepared surface with sub-base 100 mm thick compacted Granular Sub-base as per Clause 401.4 and base 75 mm thick compacted water bound macadam grading 2 as per Clause 405.3. The 150 mm thick hammer desired stones are laid in the herring one or stretched bond pattern. The stones are compacted into the bedding sand of 40 mm over the WBM base bounded by edge stone using suitable compacting device. The gaps are filled with fine sand stone dust as per Technical Specification Clause 413.4

CD

Providing concrete for plain/reinforced concrete M10 (1:3:6) in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203

Brick masonry work in cement mortar in sub structure complete excluding pointing and plastering as per drawing and technical specifications Clauses 600, 1202 & 1203 (1:4)

Pointing with cement mortar (1:3) on brickwork as per drawing and technical specification Clauses 613.3 and 1204

Plastering with cement mortar (1:4), 15mm thick on brickwork in substructure as per technical specification

Painting two coats including prime coat with epoxy paint of approved brand on concrete/steel surfaces after through cleaning of surface to give an even shade as per drawing and Technical Specification Clause 1701

Fillling in foundation trenches using coarse sand/ screening as per drawing and technical specification Clause 305.3.9

Renewal (Part2)

Construction of Subgrade and Earthen Shoulder with approved soil with all lifts and leads, laying in layers, breaking clods, dressing to required lines, curves, grade and sections, watering and compaction to meet at least 100 % procter density complete to specification requirements

Construction of Subgrade and Earthen Shoulder with approved soil with all lifts and leads 1000 mts, laying in layers, breaking clods, dressing to required lines, curves, grade and sections, watering and compaction to meet at least 100 % procter density complete to specification requirements

Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.85 kg/sqm using mechanical means as per Technical Specification Clause 502

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.275 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503.

Providing and laying bituminous concrete with 100-120 TPH batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6 per cent of mix and filler and Waste Plastic 8% of Bitumen , transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 509 complete in all respects (Waste Plastic Technology)

Painting lines, dashes, arrows, etc. on roads with hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads in two coats on new work with ready mixed road marking paint conforming to IS:164 on bituminous/concrete surface, including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control as per drawing and Technical Specification Clause 1702

Supply and Fixing of Pavement Maker (Cat Eye) Type X- ASTMD-4956-04 Avery denision /3-M (USA MAKE) consisting of ASA Plastic housing fitted with tightly adherent ploting compound. The housing shall contain prismatic to Glass covered prismatic reflecting face to reflect incident light