New Okhla Industrial Development Authority Tender

The body of FMM shall bounce back to its original position of after 750 number of hits using pendulum of 1.8 kg confirming 40 ASTM D256 adhesion between the body and outer casing body of FMM shall with stand 50kg. Tensile loads confirming to ASTM D638 method, The rate shall be include all materials,labours, T&P transportation installation and incidentals all complete as per direction of the Engineer-In-charge .

Solar Power road marker (Solar studs) The solar studs shall be made of Aluminum alloy and poly carbonate material which shall be absolutely weather resistance and strong enough to support a load of 13,635 Kg tested in accordance with ASTM D4280. Its colour may be white,red,yellow,green or blue or combination as directed by the Engineer. Its water resistance shall meet the requirements of IP 65 in accordance with IS:12063:1987 category 2 for protection against water ingress. The dimensions of solar studs shall not be less than 100mm X 100mmX10mm. It shall have super bright LEDs so as to provide long visibility from a distance of more than 800 m. Its flashing rate shall not be less than 1 Hz. Its should be able to give the prescribed performance in the temperature range-40*C to 55*C. Its life shall be not less than 3 years. The rate shall be include all materials, labour, equipments, fabrication, transportation,erection,installation and incidentals all complete as per direction of the Engineer-in-charge.

Retro-Reflective Signs (stainless steel Frame and Post with one side sings) Supply & Fixing of reflective signs board (single side) of size 1.50 x 1.20m retro reflective sheeting of HIP grade type-IV, the board shall be fixed on 50mm SS 304 grade of with a corrosion resistant 4mm thick ACM sheet of standard make as per MORTH specification. The Board shall be fixed using 2 man post 45x45x60 cm cement concrete foundation. The stainless steel joint welding of SS pipe work shall be band and grinder property inclluding bufting so and to give uniform shinging at welded of SS pipe work shall be band and grinder property. The Retro reflective sheeting shall be tested for a certificate of having the sheeting at welded joints. The Retro reflective, daytime colour and luminance, shrinkage, flexiblitily, liner removal, adhesion, impact resistance, specular glass and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obrained from international/Government Laboratory/institute by the manufacture of the sheeting and in case the certificate is obtained from internation condition, it should also be obtrained from indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively a certificate conforming to ASTM Specification (D4956-09) on artifical accelerated weathering requirements from a reputed laboratory in india can be accepted provisionally, in such a situation, the Employer/Client. if so desires, could seek for a performance guarantee, in such a situation, the Employer/Client. if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67:2012 Legends, letters, Numerals and borders etc. should be as per MoRTH spectification No. 801.3.7 Proof of the same in form of goverment report shall be uploaded white quoting tender.

6m Span over head contilever structure with 300 dia M S One Vertical Post. Supply, Fixing, eraction of built up contilever structure 6m span comprising of one vertical posts of 6.00m height made up to 300 mm NB heavy class MS pipe as vertical member welded with 10mm MS plate at top & 12mm M S Plate at bottom the horizontal Truss shall comprise of 50m dia heavy class M.S pipe as per and 40 mm dia heavy M S pipe as bracing & 10 mm MS Plate at bottom for fixing to vertical post as per structure design & drawing with one of steel primer and two coats of synthetic enamel plant. The work includes construction of RCC Foundation of size 0.90x0.90x1.50m of required depth as per site condition for build up structure including earth work in excavation 100 mm thick lean Concrete in 1:3:6 Cement coarse sand and 40mm gauge stone ballast and RCC - M25 grade concrete including supply and fixing of 25mm dia foundation bolts 600mm long as per provision of structure desing including cost of reinforcemen & shuttering. The lateral vertical clearance and complete. installtion work shall be as per relevant clauses of MORT&H specification section 800 and IRC 67 2012 complete in all respect the rates shall include cost of design fabrication, supply, transportation. Local shifting Erection of Signage structure using crane, inclusive of all taxes etc. all T& P machine. Material and labour requird for proper completion of work as per diretion of Engineer-in-charge.

Bollard (Single side) Supply & fixing of bollard made (Single Side) out of 2mm thick aluminum sheet face to be covered with high intensity prismatic grade type IV sheeting, legends letters, numerals and borders etc. should be as per Morth specification No. 801.3.7, welded poly shaped to make it monolithic pillar size 1200 mm high bollard is having a frame 900X600 mm and 600 mm dia for fixation made out of 35X35X5mm angle iron and from side is fully cover.(size of foundation 0.45X0.45X0.60m)

Retro-Reflective sheeting type-XI with 4mm thick ACM single Side Providing & Fixing of reflective signs with a corrosion resistant 4mm thick with 0.4 to 0.5 mm both side aluminium skin aluminium composite panel face to be fully covered with High intensity prismatic sheeting type XI as per IRC-67:2012 retro reflective sheeting with back frame MS angle of 35x35x5mm Legenda, letters, numerals and borders etc should be as per MoRTH specification No-801.3.7. The Sheeting shall have a pressure- Sensitive adhesive of the aggressive lack type requiring no heat. solvent other preparation for adhesion to a smooth clean surface, in a manner recommended by the sheeting manufacture. The ACM (Aluminium Composite Materials) Shall be fixed on the Back frame MS Angle with riveting. Micro Prismatic type IV Retro reflective sheeting confirming to ASTM D4956-09 Shall be pressure fixed. The Retro reflective, daytime colour and luminance, shrinkage, flexiblitily, liner removal, adhesion, impact resistance, specular glass and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obrained from international/Government Laboratory/institute by the manufacture of the sheeting and in case the certificate is obtained from internation condition, it should also be obtrained from indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively a certificate conforming to ASTM Specification (D4956-09) on artifical accelerated weathering requirements from a reputed laboratory in india can be accepted provisionally, in such a situation, the Employer/Client. if so desires, could seek for a performance guarantee, in such a situation, the Employer/Client. if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67:2012 & Proof of the same Report shall be uploaded which quoting tender. The rate shall include all materials, labour, T&P, Transportation, installation and incidentals all complete as per direction of the Engineer-in-chage.

Retro-reflectorised Traffic sign as per IRC-67-2012 providing and fixing of retro-reflectunsed cautionary, mandatory and informatory sign as per RC 67-2012 made of high intensity grade sheeting type IV vide clause 501 3. fxad over aluminum seting 15 mm thick supported on a mild steel angle von post 75 mm x 75 mm x 5 mm family fixed to the ground by means of property designed foundation with M 15 grade cement concreta 45 cm x 45 cm x 60 cm, 50 om below ground level as per approved drawing. The Retro reflective sheeting shall be tested for a certificate of having the sheeling lested for coefficient of retro refection, daytime colour and luminance, shrinkage, flexibility, nor removal, adhesion, impact resistance, specular gloss and fungus resistance 3 years outdoor weathering and shaving passed these tests shall be obtained Nom International Government Laboratory Insitute by the marvade the sheeting and in case te certificare is obtained from international condition, should also be obtained from indian condition witin 3 years of launching of product by the maculacurs in Ally, a cenficate conforming to ASTM Specification (D 4356-09) on anfical accelerared requrenents from a impres oboratory in India can be accepted provisionally. In such a stone Employer/Clert so desires could seek for a performance guarantee which would be rote sad after receipt of certificats mecting the requirement of three years outdoor weathering of the sheeting as per RC 67 2012 Legendsters numerals and borders and should be as per MoitTH specification No 801.3.7 Proof of the same in form of government report shall be uploaded while quoting tender. 60 cm equilaterale tringle with diffinitation plate (20cm X 60cm)

Retro-reflectorised Traffic sign as per IRC-67-2012 providing and fixing of retro-reflectunsed cautionary, mandatory and informatory sign as per RC 67-2012 made of high intensity grade sheeting type IV vide clause 501 3. fxad over aluminum seting 15 mm thick supported on a mild steel angle von post 75 mm x 75 mm x 5 mm family fixed to the ground by means of property designed foundation with M 15 grade cement concreta 45 cm x 45 cm x 60 cm, 50 om below ground level as per approved drawing. The Retro reflective sheeting shall be tested for a certificate of having the sheeling lested for coefficient of retro refection, daytime colour and luminance, shrinkage, flexibility, nor removal, adhesion, impact resistance, specular gloss and fungus resistance 3 years outdoor weathering and shaving passed these tests shall be obtained Nom International Government Laboratory Insitute by the marvade the sheeting and in case te certificare is obtained from international condition, should also be obtained from indian condition witin 3 years of launching of product by the maculacurs in Ally, a cenficate conforming to ASTM Specification (D 4356-09) on anfical accelerared requrenents from a impres oboratory in India can be accepted provisionally. In such a stone Employer/Clert so desires could seek for a performance guarantee which would be rote sad after receipt of certificats mecting the requirement of three years outdoor weathering of the sheeting as per RC 67 2012 Legendsters numerals and borders and should be as per MoitTH specification No 801.3.7 Proof of the same in form of government report shall be uploaded while quoting tender. 80mm x 50mm rectangular with diffinitation plate (20cm X 60cm