Municipal Corporation Tender

junction;Flooring with igh Polished Granite 16 to 18 mm thick up to 8'-00 (2.43 M) black set over base coat of cement mortar (1:6) 12 mm thick over CC bed already laid or RCC roof slab, including near cement slurry of honey like consistency spread @ 3.3.kgs per sqm & jointed with neat cement to full depth mixed with pigment of matching shade including cost of all materials like cement, sand water and tiles etc., complete, including seigniorage charges, complete for finished item of work, but excluding the cost of conveyance of all materials.H

junction;Providing and fixing Mandatory / Regulatory sign boards size 600 mm equilateral Triangle made out of Type ?XI of ASTMD 4956-09 wide angle cube cornered micro Prismatic Retro reflective sheeting and confirming to IRC 67:2012 for full background of White colour and letters/logos done by screen printing in Black colour, boarders by screen printing in Red colour and fixed over 3MM Alluminium Composite Material ( ACM ) sheet having minimum 0.30 mm thick Aluminium skin on both sides with back side painted grey colour and fixed over back support frame of M.S angle 25x25x3mm all round and fixing with 35x35x4mm and and mounted on a MS angle post of size 75x75x6mm with clear height of not less than 2.1 m from the ground level the bottom of the board. The signpost should be painted with one coat of red oxide paint and 2 coats of synthetic enamel paint Black and White colour with bands of 30cm of height. The signpost shall be firmly fixed with MS base angle 35x35x4 mm in to the ground by M15 Concrete foundation of size 450x450x600mm including cost and conveyance of all materials ,equipment, machinery and labour with all leads and lift, loading changes necessary for satisfactory completion of the work as directed by Engineer -in-Charge.(triangular)

junction;Supplying & Fixing Raised Pavement Markers (Road Studs) with Twin Moulded Shanks:- Supplying & Fixing of Molded Shanks Raised Pavement Markers made of polycarbonate and ABS moulded body and reflective panels, with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 Kg tested in accordance to ASTM D 4280 type H and complying to Specification of Category A of MORTH Circular No. RW/NH/33023/10-97-DO III , Dt 11-06-1997. The height, width and length shall not exceed 50 mm,100mm and 100mm and with minimum reflective area of 13 Sqm on each side and the slope to the base shall be 35 +/- 5 degree. The strength of detachment of the integrated cylindrical shanks. (of diameter not less than 19+/- 2mm and height not less than 30+/-2mm) from the body is to be a minimum value of 700 Kgs . Fixing will be by drilling holes on the road for the twin shanks to go inside, without nails and usign epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer.

junction;Supply and application of hot applied thermoplastic road marking compound at 250mm thick incl. reflectorising glass beads @ 250gms with reflecing glass beads, exclusive of surface applied galss bead as per IRC:35, the material should be of ASIAN/BERGER/Equivalit must comply with a)white index for the product should be in the range of 60-70 when maeasured against std. reference B) luminon factor of the material should be in the range of 80-85% at 45 C as per AASTHON 249 c) Crack restore. d) adhesion - strong e) safteny point: 102 C f) dried filing finish smoth & uniform g) night vision : High as directed by the Engineer - in - Chief carfying to IS 164 - 1961. and conforming to IRC 35-1997

junction;Supply and fixing of FRP /GRC Artistic sculptures in an any thematical shapes of defined size with specialized skilled artist worked on 3D art objects having beautif'ul design with sustainable quality, enhancing appealing view. extremely durable, long lasting Corrosion free sculpture.

junction;Painting with Synthetic Enamel paints - Two Coats including cost and conveyance and labour charges etc., complete as per standred specification. Old wood work & New iron work

junction;Artistic painting with Acrylic Exterior or higher grade paint including cost, conveyance of all material to the work site, and all operational, incidental, labour charges, Hire charges for scaffolding with required materials as per the site condition, etc complete for finished item o[ work as per the design approved by the Engineer-in-Charge

junction;Supplying, fitting and placing of precast Bollard of height 1m with diameter 200mm with natural moulded with M20 grade concrete ncluding all labour, cost and conveyance charges etc complete.

junction;Plain Cement concrete Grade M20 - Nominal Mix using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work, but excluding centering, shuttering.

junction;Flooring with Designer tiles of ant premium colour, design and of 25 mm thick set over base coat of cement mortar (1:6) 12 mm thick over CC bed already laid including near cement slurry of honey like consistency spread @ 3.3.kgs per sqm & jointed with neat cement to full depth mixed with pigment of matching shade including cost of all materials like cement, sand water and tiles etc., complete, including seigniorage charges, complete for finished item of work, but excluding the cost of conveyance of all materials

junction;Supply and placing of the M-10 Design Mix Concrete by ready mix, mixed in a batching and mixing plant as per approved mix design, for sub base over a prepared subgrade, cement content not to be less than 220Kg/Cum with crushed stone coarse aggregate of 25 mm and 12.5 mm nominal sizes graded as per table 600-1, with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, concrete strength not to be less than 10 Mpa at 7 days, including cost and conveyance of all materials like cement, sand, coarse aggregate, water, centering etc., to site, all labour charges for mixing, transported to site by transit mixer, pumping and laying concrete, centering and vibrating, curing and finishing etc. complete, including seigniorage charges and cost of steel and its fabrication charges for finished item of work, as per Technical Specification 601 MORTH etc., complete for finished item of work- For CC Roads.

junction;Filling with good Gravel soil, including supply and delivery of good gravel for filling, including cost of gravel, seinourage charges and conveyance to site, filling charges, watering, tamping and rammming and all labour charges and operational charges complete as directed by the Departmental officers.

junction;Plastering 20mm thick in two coats with base coat of 16mm thick in CM (1:6) and top coat of 4mm thick in CM (1:4) dubara sponge finish including cost and conveyance of all materials like cement, sand, water etc., to site, all operational, incidental and labour charges such as mixing mortar,scaffolding charges, lift charges, finishing,including cutting of Grooves wherever necessary as directed by Engineer - in - charge, curing, etc., complete but excluding seigniorage charges for Uneven Surfaces of Brick Wall for finished item of work. (APSS 901,903 & 904)

junction;Providing High Yield Strength Deformed (HYSD)/ Thermo Mechanically Treated (TMT) / Mild steel (MS) steel bars (Fe 415/ Fe 500 grade as per IS 1786-1979) of different diameters for RCC works , including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including sales and other taxes on all materials etc., complete for finished item of work in all floors.( APSS No.126)

junction;Supply and placing of the M25 Design Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402) with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work.

junction;Plain Cement concrete in (1:4:8) prop. Using 40 mm Hard Granite Machine Crushed metal including cost and conveyance of materials to site including curing, seignorage fee, Machine mixing, concrete laying tamping, vibrating, watering curing and all labour charges, hire and operational charges of machinery, water lead charges and including curing etc. complete for finished item of work

junction;Fixing of Pre-cast RCC kerbing blocks true to its alignment as specified by the Dept.to form divider including pointing with cement morter (1:3) prop. cost and conveyance of all materials like cement sand water etc., to site, seigniorage charges, curing all taxes and labour charges for mixing complete for finished item of work.

junction;Supply of Pre-cast CC blocks for kerbing made with rubberized moulds of M30 grade Design mix with 350 kgs Cement / Cum. Of concrete, 20mm to 6mm nominal size (SS 5) Hard Granite machine Crushed metal @ 0.80 Cum/cum. Of concrete and sand @ 0.40 Cum/cum. of concrete for RCC works including cost and conveyance of all materials like cement Sand Coarse Aggregate Water etc., to site, Seigniorage Charges, all taxes and labour charges for mixing, laying Concrete, tamping, vibrating, lifting, curing finishing top surface including hire charges of machinery and vibrator complete for finished item of work. and transportation of precast blocks from casting site to work site of each 0.60m length (CC block as per design & specification etc., complete excluding VAT.

junction;Earth work excavation for foundations and depositing on bank for all lifts with an initial lead of 10m including all operational ,incidental, labour charges such as shoring, sheeting ,planking ,strutting etc complete for finished item. excluding dewatering charges etc. as per SS-20B (APSS 308)

junction;Cutting open B.T. road surface including stacking of excavated materials including hire charges of all tools and plants and all labour charges for finished item of work as directed by the Engineer - in - Charge

junction;Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry ,cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 mas per Technical Specification Clause 202 MORD / MORTH (By mechanical means Cement concrete) etc., complete