Municipal Administration And Water Supply Department Tender

Supplying and filling in foundation and basement with Crushed Stone Sand (M-Sand) in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.- M Sand filling

Supplying and filling in foundation and basement with well gravel layer not more than 15cm thick well ramped watered and compacted etc,. Complete with standard specification

Plain Cement Concrete 1:4:8 (One part of cement, four part of Crushed Stone Sand (M- Sand) and Eight part of coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Centering for sides and soffits for plain surface such as slabs ,lintels ,sunshades, staircase waist slabs etc., including strutting 3m high using M.S sheet of size 90cm X 90 cm and 10 Gauge fitted with M.S Angle of size 25x25x3mm laid over silver work (C.Wood) joists of size 10x6.50cm spaced at about 90 c/c and supported by casurina props . 10 to 13 cm dia spaced at about 75 c/c complying with standard specification.

Grade Beam

Beams and slabs

Column

M-20 CONCRETE - Providing and laying in position, standarised design mix M-20 Grade using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325Kg/m3 and maximum water cement ratio of 0.55, including admixture(plasticiser/super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.70 cu.m.)940.50Kg of 20mm machine crushed stone jelly and with about (2.80 cu.m.)462.00Kg of 10-12mm machine crushed jelly and with about (4.25 cu.m.)701.25Kg of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor/roof slabs wherever neccessary without clambing extra, etc. complete complying with standard specification and as directed by the departmental officers. the coarse and fine aggregates to be used should comply with the requierments of IS 383-2016. (No separate payment will be made by the department for the exces usage of materials as per design mix.)

Foundation and basement

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors.

Brickwork using Country Bricks of size 8-3/4" x 4-1/4" X2-3/4"" in Cement Mortar 1:5 (One cement and five crushed stone sand) including curing neat finishing, etc., complete complying with standard specifiction.

Basement

Ground floor

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Fabricating supplying and fixing of pre painted galvanized iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Supplying and fixing of rolling shutters shall be pull and push type (Gear operated) made of 18G/3" lathe sections which consist of five main parts such as curtain, lock plate, guide channels rollers and hood cover. These five main parts are made out of special components detailed below: curtain shall be of 18G/3" lath sections cut to required size and filled with heavy cast iron / MS clips. For 8'0"(2.45m) high rolling shutter lath sections provided shall be not less than 37 numbers. Lock plate shall be 10GMS sheet and attached to the side brackets with 20mm square bar.Side brackets shall be of 10G MS plate and cast iron "U" clamps shall be rivetted to the side brackets. Roller shall be of heavy cast iron pullies fitted with heavy duty "C" class 40mm steel pipe and high tensile high carbon coil springs. 2 springs shall be supplied. Side brackets shall be of 10G MS plate and cast iron "U" clamps shall be rivetted to the side brackets. Roller shall be of heavy cast iron pullies fitted with heavy duty "C" class 40mm steel pipe and high tensile high arbon coil springs - 2 springs shall be supplied. Hood cover shall be of 0.8mm CRCA sheet reinforced with 25mmx25mmx3mm MS angle or gate channel. The rolling shutter in addition to the above should have pulling hook and shall be coated on exposed area with heavy coat of red oxide primer etc., complete.Gear Operated Type (from 8 sqm. to 12 sqm. Area) M-0402 PWD SoR 23-24

Fabrication ,Supply and Fixing of Weld Mesh Screen using 'L' Angle alround of size 40x40x5mm vertically and horizontally welded with 'L' Angle Frame and fully covered with Weld mesh of size 7.5 x 2.5mm including cost and conveyance of all material and labour charges as per standard specifications.

Plain Cement Concrete 1:2:4 (one cement, two Crushed Stone Sand (M- Sand) and four coarse aggregates) using 20mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges etc., complete as per standard specification

Plastering with cement mortar 1:5 (One part of Cement and Five part of Plastering Sand (P- Sand) 12mm, thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications

Painting two coats with ready mixed Plastic Emulsion Paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification. - 10 sq.m

Painting two coats with Ready Mixed Enamel Paint over the new iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors.

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A FT switch with painting of suitable colour for open PVC light point / fan point (for electronic regulator) (4 points per coil) SD 17 PWD Electrical Data

Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 900V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 93 mm TW switch box with 3mm hylum sheet cover for 5A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point.etc, complete as per standard specifications. SD 38 PWD Electrical Data

Supply and fixing of single box type 4' x 40 W fluorescent fitting complete with copper choke and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed copper leads from terminals to the fitting including cost of all material charges and labour charges etc, complete as per standard specification SD 88 PWD Electrical Data 23-24

Supplying and fixing of 1200mm ( 48'' ) sweep AC ceiling fan complete with regulator with 1M down rod including S & F of fan clamp with side plates and cross arm etc, complete as per standard specifications SD 107 PWD Electrical Data 23-24

Earthling as per ISI Specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm and with 20mm dia copper earth flat of size 125mm x50mmx6mm, with funneling arrangement using charcoal, common salt, G.I.reducer, check nuts etc., and masonry work and providing RCC cover slab 38mm thick for the Brick masonry including cost of steel and fabrication of reinforcement etc., complete in all respects as directed by the departmental officers. SD 233 PWD Electrical Data 23-24

Supplying and Fixing of 3 Phase DB with MCB 12 way TPMCB sheet steel distribution boards (flush type/surface type) fitted with bus bars and neutral links with three phase MCB outgoings and separate 4 way provision for accommodating One No. 4 pile incoming MCB / Isolator and another separate 4 way provision for accommodating One No. 4 pole ELCB / RCD (totally 8 ways in one segment) (3 x 4 ways in each segment) and separate provisions for MCB / Isolator (totally 12 Nos.) for sub incomers in 3 segments with label holder etc.complete in all respects as directed by the departmental officers SD 01 PWD Electrical Data 23-24

Supply and run of 2 of 4sqmm (56/0.3) PVC insulated SC unsheathed copper conductor of 1100v of 7/20 GI bearer wire for` service connection mains including cost and conveyance of all materials to site and labour charges etc, complete complying with standard specification SD 65 PWD Electrical Data 23-24

Supply,Delivery and fixing of 25mm dia GI service pipe including cost of all material charges and labour charges etc., complete as per Specifications. (L.R)

Supply,Delivery and fixing of Industrial type heavy duty Exhaust Fan mountable in light roofing including cost of all material charges and labour charges etc., complete as per Specifications.

Supply and Delivery of Sorting Table (size 8 x 1.5 x 1m) which includes labour,transportation, necessary wiring arrangements if required cost and conveyance of all materials in site etc.,Complete

Supply and Delivery of Electronic weighing scale 2000KG capacity which includes labour,transportation, necessary wiring arrangements if required cost and conveyance of all materials in site etc.,Complete

Supply, fixing and commissioning a Vertical type of Hydraulic Bailing machine to bale paper carton box and other plastic materials, Weight 70- 100 Kgs, bale size of 0.7x 0.7 x 1m (LBD) working presure 138 bar , no of cylinders 2 , motor capaicty 7.46 KW, production capacity 2500 - 3000 kg per day applicable to all type plastic ( PET, HDPE, LDPE, MLP, PAPER CLOTHES) including conveance and all labour harges etc,complete with standard specification.

Supply, fixing and commissioning of Plastic shredder machine( grinding of all 7 category of plastic waste ) wit 6 blades size of 46 x 13cm , with shredding capacity of 200 to 250 kg per hour having motor capaity of 15 to 22.5 Kw with cast iron body including conveance and all labour harges etc,complete with standard specification.

Supply and Delivery of manual Fork lift of capacity 100kg capacity including all labour charges etc,complete with standard specification.

GST 18%