Public Works Department Tender

Providing, laying & fixing in position RCC spun or hume pipes ISI marked with proper jointing in required slope packed in the gasket of hume or spun yarn and neatly finished with rich grout of cement moratar 1:3 or having flexible rubber ring joint made with prefectly air and water tight including testing of joints as per MoRTH Specfication : Clause : 1000 & 2900 NP - 3, 300 mm dia

Supply of informatory / retro reflective sign board size 60 x 80 cm made out of 2.0 mm thick aluminum sheet face to be fully covered by white / blue high intensity grade retro reflective sheeting with Red/ white symbol, cut out or screen printed background with epoxy paint, complete confirming to MoRTH specifications clause 801 with angle iron post 65 x 65 x 6 mm, 3 Mtr. Long.

Installation of sign boards having the posts like mandantory, cautionary and informatory boards including excavation, fixing of posts in 300 mm dia. RCC hume pipe (IS marked) 1.20 m long, 75 cm embedded in ground, the in side of pipe shall be filled with cement concrete 1 : 4 : 8 with semi-circular hump at top, the pipe shall be painted white with enamel paint including transportation etc. complete. For double post

P& F Mukhya Mantri Sadak Yojana logo for roads funded by State road fund having M.S. Definition plate of 1.6mm thickness frame to steel hollow dsection of 75mm x 75mm, 2.5m long stove enamelled paint with hold fast including paint logo as per approved design and colours. The logo shall be made out of 1.6mm thick circular plate fix on 1200mm x 150mm rectangular steel base plate 1.6mm thick, the base of circular shall be plain at the junction of base plate. The size of definition plate shall be 1500x600mm and embedding the posts by M-15 mix C.C. block 300x300x600 mm including lettering / writing and painting etc. complete in all respect

PART 'B' ROAD SIDE DRAIN Earth work in excavation in foundation trenches etc.in drains and channels etc. not exceeding 2m.depth, including dress-sing of bottom and sides of trenches, stacking the excavated soil 3m clear from the edge of excavation including disposal of surplus soil as directed within a lead of 1000 metres [MoRTH Specification : Clause 301,30 Hard soil

Providing and laying mechanically mixed and vibrated Cement Concrete in foundation upto a depth of 1.5 metres below ground level and 1.50 metres above Ground/Bed level as per MoRTH Specification : Clause 1000 & 1700 P.C.C. 1:3:6 mix with crushed stone aggregate 20 mm nominal size.

Providing and laying Plain cement concrete mix with stone aggregate 20 mm nominal size mechnically mixed and vibrated in foundation up to a depth of 1.50 metres below ground level and/or 1.50 metres above ground/bed level as per MoRTH specification : clause 1000 & 1700. with all lead P.C.C. grade M-15 in foundation & plinth upto 1.5 mtr. from ground level

Part 'II' Garba chowk to satyanarayan teli's house PART 'A' ROAD WORK Construction of un-reinforced, without Dowl Bar plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per MoRTH specification clause 602.

Supply of informatory / retro reflective sign board size 60 x 80 cm made out of 2.0 mm thick aluminum sheet face to be fully covered by white / blue high intensity grade retro reflective sheeting with Red/ white symbol, cut out or screen printed background with epoxy paint, complete confirming to MoRTH specifications clause 801 with angle iron post 65 x 65 x 6 mm, 3 Mtr. Long.

Installation of sign boards having the posts like mandantory, cautionary and informatory boards including excavation, fixing of posts in 300 mm dia. RCC hume pipe (IS marked) 1.20 m long, 75 cm embedded in ground, the in side of pipe shall be filled with cement concrete 1 : 4 : 8 with semi-circular hump at top, the pipe shall be painted white with enamel paint including transportation etc. complete. For double post

P& F Mukhya Mantri Sadak Yojana logo for roads funded by State road fund having M.S. Definition plate of 1.6mm thickness frame to steel hollow dsection of 75mm x 75mm, 2.5m long stove enamelled paint with hold fast including paint logo as per approved design and colours. The logo shall be made out of 1.6mm thick circular plate fix on 1200mm x 150mm rectangular steel base plate 1.6mm thick, the base of circular shall be plain at the junction of base plate. The size of definition plate shall be 1500x600mm and embedding the posts by M-15 mix C.C. block 300x300x600 mm including lettering / writing and painting etc. complete in all respect

Providing and fixing of speed breakers made of abs poly carbonate alloy yellow & black made individually size 500x400x50 mm with two side reflectors of yellow colour 6 nos suitable holes provided on it for fixing it on road with the help of MS nails with three abtes locking arrangement on side of the speed breaker. It is to be fixed on road after cement concrete on the hollow blocks provided in the bottom.

Part 'III' Gautam ashram to Nagauri's house PART 'A' ROAD WORK Construction of un-reinforced, without Dowl Bar plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per MoRTH specification clause 602.

Earthwork in excavation in foundation trenches etc. not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil 3m. Clear from the edge of excavation and subsequent filling around hume pipes/masonry in 15cm layers with compaction including disposal of all surplus soil as directed within a lead of 1000 metres.[MoRTH Specification : Clause 301,304]. Hard soil mixed with kankar, boulder etc.upto 20%

Providing and laying mechanically mixed and vibrated Cement Concrete in foundation upto a depth of 1.5 metres below ground level and 1.50 metres above Ground/Bed level as per MoRTH Specification : Clause 1000 & 1700 P.C.C. 1:3:6 mix with crushed stone aggregate 20 mm nominal size.

P& F Mukhya Mantri Sadak Yojana logo for roads funded by State road fund having M.S. Definition plate of 1.6mm thickness frame to steel hollow dsection of 75mm x 75mm, 2.5m long stove enamelled paint with hold fast including paint logo as per approved design and colours. The logo shall be made out of 1.6mm thick circular plate fix on 1200mm x 150mm rectangular steel base plate 1.6mm thick, the base of circular shall be plain at the junction of base plate. The size of definition plate shall be 1500x600mm and embedding the posts by M-15 mix C.C. block 300x300x600 mm including lettering / writing and painting etc. complete in all respect

Providing and fixing of speed breakers made of abs poly carbonate alloy yellow & black made individually size 500x400x50 mm with two side reflectors of yellow colour 6 nos suitable holes provided on it for fixing it on road with the help of MS nails with three abtes locking arrangement on side of the speed breaker. It is to be fixed on road after cement concrete on the hollow blocks provided in the bottom.

Part 'IV' Mod ke balaji to kile ka darwaja via patwa mohalla PART 'A' ROAD WORK Construction of un-reinforced, without Dowl Bar plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per MoRTH specification clause 602.

Supply of informatory / retro reflective sign board size 60 x 80 cm made out of 2.0 mm thick aluminum sheet face to be fully covered by white / blue high intensity grade retro reflective sheeting with Red/ white symbol, cut out or screen printed background with epoxy paint, complete confirming to MoRTH specifications clause 801 with angle iron post 65 x 65 x 6 mm, 3 Mtr. Long.

Installation of sign boards having the posts like mandantory, cautionary and informatory boards including excavation, fixing of posts in 300 mm dia. RCC hume pipe (IS marked) 1.20 m long, 75 cm embedded in ground, the in side of pipe shall be filled with cement concrete 1 : 4 : 8 with semi-circular hump at top, the pipe shall be painted white with enamel paint including transportation etc. complete. For double post

P& F Mukhya Mantri Sadak Yojana logo for roads funded by State road fund having M.S. Definition plate of 1.6mm thickness frame to steel hollow dsection of 75mm x 75mm, 2.5m long stove enamelled paint with hold fast including paint logo as per approved design and colours. The logo shall be made out of 1.6mm thick circular plate fix on 1200mm x 150mm rectangular steel base plate 1.6mm thick, the base of circular shall be plain at the junction of base plate. The size of definition plate shall be 1500x600mm and embedding the posts by M-15 mix C.C. block 300x300x600 mm including lettering / writing and painting etc. complete in all respect

Providing and fixing of speed breakers made of abs poly carbonate alloy yellow & black made individually size 500x400x50 mm with two side reflectors of yellow colour 6 nos suitable holes provided on it for fixing it on road with the help of MS nails with three abtes locking arrangement on side of the speed breaker. It is to be fixed on road after cement concrete on the hollow blocks provided in the bottom.

Part 'V' Panghat ke balaji to mukesh sen's house in ward no. 10 PART 'A' ROAD WORK Construction of un-reinforced, without Dowl Bar plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per MoRTH specification clause 602.

Supply of informatory / retro reflective sign board size 60 x 80 cm made out of 2.0 mm thick aluminum sheet face to be fully covered by white / blue high intensity grade retro reflective sheeting with Red/ white symbol, cut out or screen printed background with epoxy paint, complete confirming to MoRTH specifications clause 801 with angle iron post 65 x 65 x 6 mm, 3 Mtr. Long.

Installation of sign boards having the posts like mandantory, cautionary and informatory boards including excavation, fixing of posts in 300 mm dia. RCC hume pipe (IS marked) 1.20 m long, 75 cm embedded in ground, the in side of pipe shall be filled with cement concrete 1 : 4 : 8 with semi-circular hump at top, the pipe shall be painted white with enamel paint including transportation etc. complete. For double post

P& F Mukhya Mantri Sadak Yojana logo for roads funded by State road fund having M.S. Definition plate of 1.6mm thickness frame to steel hollow dsection of 75mm x 75mm, 2.5m long stove enamelled paint with hold fast including paint logo as per approved design and colours. The logo shall be made out of 1.6mm thick circular plate fix on 1200mm x 150mm rectangular steel base plate 1.6mm thick, the base of circular shall be plain at the junction of base plate. The size of definition plate shall be 1500x600mm and embedding the posts by M-15 mix C.C. block 300x300x600 mm including lettering / writing and painting etc. complete in all respect

Providing and fixing of speed breakers made of abs poly carbonate alloy yellow & black made individually size 500x400x50 mm with two side reflectors of yellow colour 6 nos suitable holes provided on it for fixing it on road with the help of MS nails with three abtes locking arrangement on side of the speed breaker. It is to be fixed on road after cement concrete on the hollow blocks provided in the bottom.

Part 'VI' Purani abadi samudayik bhawan to shamshan ghat PART 'A' ROAD WORK Construction of un-reinforced, without Dowl Bar plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per MoRTH specification clause 602.

Supply of informatory / retro reflective sign board size 60 x 80 cm made out of 2.0 mm thick aluminum sheet face to be fully covered by white / blue high intensity grade retro reflective sheeting with Red/ white symbol, cut out or screen printed background with epoxy paint, complete confirming to MoRTH specifications clause 801 with angle iron post 65 x 65 x 6 mm, 3 Mtr. Long.

Installation of sign boards having the posts like mandantory, cautionary and informatory boards including excavation, fixing of posts in 300 mm dia. RCC hume pipe (IS marked) 1.20 m long, 75 cm embedded in ground, the in side of pipe shall be filled with cement concrete 1 : 4 : 8 with semi-circular hump at top, the pipe shall be painted white with enamel paint including transportation etc. complete. For double post

P& F Mukhya Mantri Sadak Yojana logo for roads funded by State road fund having M.S. Definition plate of 1.6mm thickness frame to steel hollow dsection of 75mm x 75mm, 2.5m long stove enamelled paint with hold fast including paint logo as per approved design and colours. The logo shall be made out of 1.6mm thick circular plate fix on 1200mm x 150mm rectangular steel base plate 1.6mm thick, the base of circular shall be plain at the junction of base plate. The size of definition plate shall be 1500x600mm and embedding the posts by M-15 mix C.C. block 300x300x600 mm including lettering / writing and painting etc. complete in all respect

Providing and fixing of speed breakers made of abs poly carbonate alloy yellow & black made individually size 500x400x50 mm with two side reflectors of yellow colour 6 nos suitable holes provided on it for fixing it on road with the help of MS nails with three abtes locking arrangement on side of the speed breaker. It is to be fixed on road after cement concrete on the hollow blocks provided in the bottom.