Puducherry Smart City Development Limited Tender

Supply and Fixng of Waist Twsiter: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must be submitted during the technical bid and the same must reflect clearly on the notified certifying bodies websites as online verification is mandatory during technical bid. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 1.35 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. Circular Handrail Dia 42 mm fabricated from 42 O.D. galvanized steel pipes.The poles are welded on to a base plate made from steel with 114mm inner diameter. An Internal limiter prevents the equipment from moving uncontrollably.Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. Equipment Dimensions: 1.44 m x 1.29 m x 1.35 m with following standards 1. All products must be tested and certified to meet EN16630 safety standards with GS test marks. 2. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only.3. The GS mark EN16630 certificates must be in the name of supplier by themselves or through their authorized dealers or contractors. 4. These EN16630certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. 5. All Tubular steel of 2.5mm thickness are galvanized and zinc dipped 6. All Joints should be Robotic Welded. 7. All metal parts are powder coated using – Great Wall Powder (or equivalent) to the thickness of 80-120 microns. 8. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. 9. The limiters must be in accordance with EN16630 safety norms. 10. Seat(s) and footrest, if any – Shall be made of LDPE material and fixed to the main frame 11. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be tamper resistant stainless steel. 12. Exposed hardware shall be covered with ultra violet stabilized plastic safety caps as a safety feature against protruding hardware, aesthetic pleasing against ugly exposed hardware and prevention against vandalism as well. 13. All open ends of pipe to be closed with GI/LLDPE caps, base plate cover shall be made of virgin LLDPE plastic by rotational molding with minimum 8mm thickness, UV resistant and colour as approved by Engineer-in-Charge. 14. High quality grip rubber should be used on handles. 15. Foothold shall be fixed on ground with concrete 1:2:4 and J shaped welded bolts and installed as per manufacturer specifications.

Supply and Fixng of Leg Stretch: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must be submitted during the technical bid and the same must reflect clearly on the notified certifying bodies websites as online verification is mandatory during technical bid.All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 1.10 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. Handrail rails of Dia 32 m. The poles are welded on to a base plate made from steel with 114mm inner diameter. Welded. Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety lim iters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 0.93 m x 0.81 m x 1.13 m with following standards 1. All products must be tested and certified to meet EN16630 safety standards with GS test marks. 2. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. 3. The GS mark EN16630 certificates must be in the name of supplier by themselves or through their authorized dealers or contractors. 4. These EN16630certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. 5. All Tubular steel of 2.5mm thickness are galvanized and zinc dipped 6. All Joints should be Robotic Welded. 7. All metal parts are powder coated using – Great Wall Powder (or equivalent) to the thickness of 80-120 microns. 8. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. 9. The limiters must be in accordance with EN16630 safety norms. 10. Seat(s) and footrest, if any – Shall be made of LDPE material and fixed to the main frame 11. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be tamper resistant stainless steel. 12. Exposed hardware shall be covered with ultra violet stabilized plastic safety caps as a safety feature against protruding hardware, aesthetic pleasing against ugly exposed hardware and prevention against vandalism as well. 13. All open ends of pipe to be closed with GI/LLDPE caps, base plate cover shall be made of virgin LLDPE plastic by rotational molding with minimum 8mm thickness, UV resistant and colour as approved by Engineer-in-Charge. 14. High quality grip rubber should be used on handles. 15. Foothold shall be fixed on ground with concrete 1:2:4 and J shaped welded bolts and installed as per manufacturer specifications.

Supply and Fixng of Rider: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must be submitted during the technical bid and the same must reflect clearly on the notified certifying bodies websites as online verification is mandatory during technical bid. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 0.5 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. A single seat of size 330 mm x 250 mm fixed to the top of the vertical post and two Pedals & Bars of size 145 mm x 50 mm and Dia 38 mm fabricated from 40 O.D. galvanized steel pipes. The poles are welded on to a base plate made from steel with 114mm inner diameter. Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 0.91 m x 0.65 m x 1.27 m with following standards 1. All products must be tested and certified to meet EN16630 safety standards with GS test marks. 2. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. 3. The GS mark EN16630 certificates must be in the name of supplier by themselves or through their authorized dealers or contractors. 4. These EN16630certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. 5. All Tubular steel of 2.5mm thickness are galvanized and zinc dipped 6. All Joints should be Robotic Welded. 7. All metal parts are powder coated using – Great Wall Powder (or equivalent) to the thickness of 80-120 microns. 8. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. 9. The limiters must be in accordance with EN16630 safety norms. 10. Seat(s) and footrest, if any – Shall be made of LDPE material and fixed to the main frame 11. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be tamper resistant stainless steel. 12. Exposed hardware shall be covered with ultra violet stabilized plastic safety caps as a safety feature against protruding hardware, aesthetic pleasing against ugly exposed hardware and prevention against vandalism as well. 13. All open ends of pipe to be closed with GI/LLDPE caps, base plate cover shall be made of virgin LLDPE plastic by rotational molding with minimum 8mm thickness, UV resistant and colour as approved by Engineer-in-Charge. 14. High quality grip rubber should be used on handles. 15. Foothold shall be fixed on ground with concrete 1:2:4 and J shaped welded bolts and installed as per manufacturer specifications.

Supply and Fixng of Seated Chest Press: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must be submitted during the technical bid and the same must reflect clearly on the notified certifying bodies websites as online verification is mandatory during technical bid All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 1.88 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. Two pair of U-Shaped Bars of 1.02 m and Dia 40 mm while the handles are placed at a spacing of 698 mm fabricated from 40 O.D. galvanized steel pipes. The poles are welded on to a base plate made from steel with 114mm inner diameter. Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 1.82 m x 0.69 m x 1.88 m with following standards 1. All products must be tested and certified to meet EN16630 safety standards with GS test marks. 2. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. 3. The GS mark EN16630 certificates must be in the name of supplier by themselves or through their authorized dealers or contractors. 4. These EN16630certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. 5. All Tubular steel of 2.5mm thickness are galvanized and zinc dipped 6. All Joints should be Robotic Welded. 7. All metal parts are powder coated using – Great Wall Powder (or equivalent) to the thickness of 80-120 microns. 8. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. 9. The limiters must be in accordance with EN16630 safety norms. 10. Seat(s) and footrest, if any – Shall be made of LDPE material and fixed to the main frame 11. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be tamper resistant stainless steel. 12. Exposed hardware shall be covered with ultra violet stabilized plastic safety caps as a safety feature against protruding hardware, aesthetic pleasing against ugly exposed hardware and prevention against vandalism as well. 13. All open ends of pipe to be closed with GI/LLDPE caps, base plate cover shall be made of virgin LLDPE plastic by rotational molding with minimum 8mm thickness, UV resistant and colour as approved by Engineer-in-Charge. 14. High quality grip rubber should be used on handles. 15. Foothold shall be fixed on ground with concrete 1:2:4 and J shaped welded bolts and installed as per manufacturer specifications.

Supply and Fixng of Health Walker: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must be submitted during the technical bid and the same must reflect clearly on the notified certifying bodies websites as online verification is mandatory during technical bid. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 1.25 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. Two numbers of Foot Rest of size 361 mm x 161 mm are attached to the Standing Bars 957mm x 60 mm fabricated from 60 O.D. galvanized steel pipes. The poles are welded on to a base plate made from steel with 114mm inner diameter. An Internal limiter prevents the equipment from moving uncontrollably. Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 1.18 m x 0.553 m x 1.25 m with following standards 1. All products must be tested and certified to meet EN16630 safety standards with GS test marks. 2. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. 3. The GS mark EN16630 certificates must be in the name of supplier by themselves or through their authorized dealers or contractors. 4. These EN16630certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. 5. All Tubular steel of 2.5mm thickness are galvanized and zinc dipped 6. All Joints should be Robotic Welded. 7. All metal parts are powder coated using – Great Wall Powder (or equivalent) to the thickness of 80-120 microns. 8. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. 9. The limiters must be in accordance with EN16630 safety norms. 10. Seat(s) and footrest, if any – Shall be made of LDPE material and fixed to the main frame 11. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be tamper resistant stainless steel. 12. Exposed hardware shall be covered with ultra violet stabilized plastic safety caps as a safety feature against protruding hardware, aesthetic pleasing against ugly exposed hardware and prevention against vandalism as well. 13. All open ends of pipe to be closed with GI/LLDPE caps, base plate cover shall be made of virgin LLDPE plastic by rotational molding with minimum 8mm thickness, UV resistant and colour as approved by Engineer-in-Charge. 14. High quality grip rubber should be used on handles. 15. Foothold shall be fixed on ground with concrete 1:2:4 and J shaped welded bolts and installed as per manufacturer specifications.

Supply and Fixng of Self Weighted Rower: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must be submitted during the technical bid and the same must reflect clearly on the notified certifying bodies websites as online verification is mandatory during technical bid. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Horizontal bars of length 1.26 m is to be schedule HOT DIP Galvanized steel with a 60mm O.D. and 2.2mm (wall) thickness of the tubing. Handle Bars of 0.74 m and Dia 38 mm fabricated from 40 O.D. galvanized steel pipes. The poles are welded on to a base plate made from steel with 114mm inner diameter. Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 1.26 m x 0.80 m x 1.59 m with following standards 1. All products must be tested and certified to meet EN16630 safety standards with GS test marks. 2. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. 3. The GS mark EN16630 certificates must be in the name of supplier by themselves or through their authorized dealers or contractors. 4. These EN16630certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. 5. All Tubular steel of 2.5mm thickness are galvanized and zinc dipped 6. All Joints should be Robotic Welded. 7. All metal parts are powder coated using – Great Wall Powder (or equivalent) to the thickness of 80-120 microns. 8. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. 9. The limiters must be in accordance with EN16630 safety norms. 10. Seat(s) and footrest, if any – Shall be made of LDPE material and fixed to the main frame 11. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be tamper resistant stainless steel. 12. Exposed hardware shall be covered with ultra violet stabilized plastic safety caps as a safety feature against protruding hardware, aesthetic pleasing against ugly exposed hardware and prevention against vandalism as well. 13. All open ends of pipe to be closed with GI/LLDPE caps, base plate cover shall be made of virgin LLDPE plastic by rotational molding with minimum 8mm thickness, UV resistant and colour as approved by Engineer-in-Charge. 14. High quality grip rubber should be used on handles. 15. Foothold shall be fixed on ground with concrete 1:2:4 and J shaped welded bolts and installed as per manufacturer specifications.

Supply and Fixng of Elliptical Cross Trainer: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must be submitted during the technical bid and the same must reflect clearly on the notified certifying bodies websites as online verification is mandatory during technical bid. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 1.25 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. Two numbers of Foot rest of size 320 mm x 132 mm are attached to the Standing Bars 998 mm x 40 mm fabricated from 40 O.D. galvanized steel pipes. Lower part of Support Handrails of size 0.8 m high and Dia 47 mm and Upper part of Support Handrails of size 0.51 m high and Dia 32 mm fabricated from 47 mm O.D. and 32 mm O.D. galvanized steel pipes. The poles are welded on to a base plate made from steel with 114mm inner diameter. Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 1.02 m x 0.53 m x 1.52 m with following standards 1. All products must be tested and certified to meet EN16630 safety standards with GS test marks. 2. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. 3. The GS mark EN16630 certificates must be in the name of supplier by themselves or through their authorized dealers or contractors. 4. These EN16630certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. 5. All Tubular steel of 2.5mm thickness are galvanized and zinc dipped 6. All Joints should be Robotic Welded. 7. All metal parts are powder coated using – Great Wall Powder (or equivalent) to the thickness of 80-120 microns. 8. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. 9. The limiters must be in accordance with EN16630 safety norms. 10. Seat(s) and footrest, if any – Shall be made of LDPE material and fixed to the main frame 11. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be tamper resistant stainless steel. 12. Exposed hardware shall be covered with ultra violet stabilized plastic safety caps as a safety feature against protruding hardware, aesthetic pleasing against ugly exposed hardware and prevention against vandalism as well. 13. All open ends of pipe to be closed with GI/LLDPE caps, base plate cover shall be made of virgin LLDPE plastic by rotational molding with minimum 8mm thickness, UV resistant and colour as approved by Engineer-in-Charge. 14. High quality grip rubber should be used on handles. 15. Foothold shall be fixed on ground with concrete 1:2:4 and J shaped welded bolts and installed as per manufacturer specifications.

Supply and Fixng of Bicycle: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must be submitted during the technical bid and the same must reflect clearly on the notified certifying bodies websites as online verification is mandatory during technical bid. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 1.31 m is to be schedule HOT DIP Galvanized steel with a 60 mm O.D. and 2.2mm (wall) thickness of the tubing. Two numbers of Pedal of size 113mm x 40mm & Rotating Disc of Dia 380 mm fabricated from 40 O.D. galvanized steel pipes. The poles are welded on to a base plate made from steel with 114mm inner diameter. Welded. Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 1.11m x 0.51 m x 1.31 m with following standards 1. All products must be tested and certified to meet EN16630 safety standards with GS test marks. 2. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. 3. The GS mark EN16630 certificates must be in the name of supplier by themselves or through their authorized dealers or contractors. 4. These EN16630certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. 5. All Tubular steel of 2.5mm thickness are galvanized and zinc dipped 6. All Joints should be Robotic Welded. 7. All metal parts are powder coated using – Great Wall Powder (or equivalent) to the thickness of 80-120 microns. 8. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. 9. The limiters must be in accordance with EN16630 safety norms. 10. Seat(s) and footrest, if any – Shall be made of LDPE material and fixed to the main frame 11. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be tamper resistant stainless steel. 12. Exposed hardware shall be covered with ultra violet stabilized plastic safety caps as a safety feature against protruding hardware, aesthetic pleasing against ugly exposed hardware and prevention against vandalism as well. 13. All open ends of pipe to be closed with GI/LLDPE caps, base plate cover shall be made of virgin LLDPE plastic by rotational molding with minimum 8mm thickness, UV resistant and colour as approved by Engineer-in-Charge. 14. High quality grip rubber should be used on handles. 15. Foothold shall be fixed on ground with concrete 1:2:4 and J shaped welded bolts and installed as per manufacturer specifications.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms , lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed , within a lead of 50m -All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50m and lift upto 1.5m.

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30cm measured at a height of 1m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size)

Centring and shuttering including strutting , propping etc. and removal of form work for - retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc.

Providing and laying 22 mm thick factory made pre-polished cement concrete flooring tiles of required colour and design over 20 mm thick cement mortar 1:4 (1 cement : 4 sand ) and jointed with cement slurry mixed with an admixture of pigment to match the shade of the tile - (Endura \ Ultra \ Dazzle \ Technic)

6 mm cement plaster 1:3 (1 cement : 3 fine sand) finished with a floating coat of neat cement and thick coat of lime wash on top of walls when dry for bearing of R.C.C. slabs and beams

Finishing with epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface , etc.complete - on concretel work

Supply of Quarry rubbish including stacking to department gauge for premeasurement and spreading required thickness

Disposal of earth/moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge.