Tourism And Cultural Affairs Department Tender

Removing old paint from steel and other metal surfaces and making the surfaces evenwith hand scrapping, scaffolding etc. complete. SSR 2022-23 Page No. 224 Item No. 35.18

Removing cement tiles, or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts etc. complete SSR 2022-23 Page No. 297 Item No. 46.19

Cleaning the existing surface by mechanical means such as sand blasting so as to remove all the existing loose rust etc. Cleaning the existing concrete substrate to achieve maximum adhesion between the coating and substrate. Free the surface from loose material, grease and oil by water jet/mechanical means. Dry the surface completely. Providing and applying one coat of Two component, solvent free, substituted long chain nylon reticulant based coating/primer as approved by Engineer in charge. This should be followed by two coats of protective two component, acyclic polyisocyanate reticulant (APR) based, UV resistant coating as approved by Engineer in charge. Apply the coats by brush or spray at 4-6 hours interval between each coat. Manufacturer of the coating shall be Dakks ISO 9001:2015 accredited for manufacturing and design; & have a track record of supplying the anticarbonation coating internationally. Two Component, Air Drying, Acyclic, Polyisocyanate Reticulant (APR) based coating should have following properties: 1. Carbon dioxide diffusion equivalent air layer thickness (DIN EN 1062-6): 200 m 2. Carbon dioxide diffusion resistance co-efficient (DIN EN 1062-6): 1.0 X 10^5 3. Elongation of cured film shall be as per ASTM D 2370/98: 17 % 4. Chloride Ion Diffusion (ASTM C 1556): 8.61 X 10^-12 5. The top coat shall have a minimum 5 year track record of use in the weather conditions of the Mumbai region 6. Minimum DFT of the entire coating system: 250 micron 7. Solid content of the base coat material: 95% 8. Solid content of the top coat material: 37% 9. The shade of the top coat should be different from the shade of the base anti-carbonation coating. 10. The base anticarbonation coating material shall have evaluated test reports demonstrating conformance to the following properties when tested from a research institution NBA accredited Grade A and internationally ranked among top 5 research institutions in the world in Annual Survey conducted by Georgia Institute of Technology ranking of research institutions. It shall be applied as per manufacturer’s specification. (If scaffolding is required, same shall be provided and will be paid under relevant item) SSR 2022-23 Page No.438 Item No. 52.31

Removing the existing cement plaster of any thickness without causing dust nuisance and stacking the debris upto a distance of 50 metres or spreading in the compound and cleaning the site etc. complete.S.S.R. 2022 - 23 Page No.211, Item No.32.33

Dismantling brick masonry in lime or cement mortar and stacking the materils as directed with all leads, lifts etcS.S.R. 2022 - 23 Page No.296, Item No.46.09

Removing doors and windows with frames and stacking the materials as directed with all leads, lifts etc. complete S.S.R. 2022 - 23 Page No.296, Item No.46.15

Removal of telephone / Electric poles including excavation and dismantling offoundationconcrete and lines under the supervision of concerned department, disposal with all liftsand up to a lead of 1000 metres and stacking the serviceable and unserviceable materialseparately S.S.R. 2022 - 23 Page No.72, Item No.7.25

Dismantling the R.C.C. Work 1:2:4 and sorting out the materials such as steel etc. as directed and stacking them within the specified lead as directed etc. complete.SSR 2022-23 Page No.297 Item No.46.29

Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. Note:- (1) The elevational area of the scaffolding shall be measured for payment purpose. (2) The payment will be made once only for execution of all items for such works.SSR 2022-23 Page No.299 Item No.46.42

Numbering the monument elements in proper order before lowering down with approved colour and shade as directed by Engineer in-charge, including ladder, scaffolding etc.complete.NON SSR R.A No.203

Lowering down carefully existing stone masonry of the monument manually in proper order including shifting the stone elements up to a distance of 50 meter beyond the monument area and stacking them as directed by Engineer in-charge, removing building rubbish and cleaning the site etc. complete .NON SSR R.A No.204

Providing Lime Pointing to stone work in lime mortar 1:1 in superstructure, as per detailed specifications and drawings or as directed including all face or visible work shall be pointed, unless otherwise specified and shall be done while the mortar is fresh, the mortar shall consists of lime and fine sand shall not be ground fine but sand should be finer, the joints of the pointed work shall be neatly defined by the pointing, the lines shall be regular and uniform in breadth and the joints shall be raised or flat as may directed, preparing the lime mortar with 640 gram pulp of wood apple (Belfruit) per cubic metre of lime mortar as a bonding material, watering and all work when handed over to be perfectly clean and free from all mortar stains etc. complete Non - S.S.R. Item From Rate Analysis No. 136 of Deapartment Rate Abstract

Providing and grouting with lime and fine screened sand slurry in proporation of (1 : 1) with a proper jet pump pressure including cleaning and washing and packing the existing crack / holes in the brick or stone masnory with lime and finesand paste in proporation of (1:1) properly from down side, filling the slurry in cracks or holes including all necessary actions and required tools and machineries, scaffolding, curing etc. complete. for soil stabilization Non S.S.R.

Excavation for foundation in earth, soils of all types sand, gravel and soft murum,Including removing the excavated matreial upto a distance of 50 M beyond the building area stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling ,ramming, watering Including shoring and strutting etc.complete ( Lift upto 1.50m ) SSR 2022-23 Page No.153 Item No. 21.02

Providing soling using 80 mm size trap metal in 15 cm. layer including filling voids with Crushed sand/grit, ramming, watering etc. complete. SSR 2022-23 Page No.157 Item No. 21.40

Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for foundation and bedding / steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete.The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.(Wooden centering will not be allowed.),with fully automatic micro processorbased PLC with SCADA enabled reversible Drum Type mixer/concrete Batchmix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)SSR 2022-23 Page No.175 Item No. 24.04

Providing Un-coursed Rubble Masonry of trap / granite stones in lime mortar 1:1½, in foundation and plinth as per detailed specifications and drawings or as directed including the stones to be set in the work as received from the quarry, after merely knocking off weak corners and edges with the masons hammer, the stones shall be carefully laid so as to break joints, no joint shall exceed 12.5 mm. (½″) in thickness, every stone shall be set flush in mortar, the face stone shall be for greater size, and good beds, one through stone shall be inserted at least every 0.80 sq. mete (1 square yard), the joints shall be racked out carefully at least 25 mm. (1″) where pointing or plastering to be done, striking joints where no pointing or plastering is to be done, preparing the lime mortar in lime miller, bailing out water, watering and all exposed masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete..(NON SSR R.A No.87)

Providing and fixing Stone Paving, Second Sort in lime 1:1/2 mortar, with average size of stone 0.45 m. x 0.30 m. x 0.15m. as per detailed specifications and drawings or as directed including all stone slabs to of approved quality, hard, even, sound, durable and uniform thickness, the stones to be very finely chisel-dressed on the surface and the course to be of prescribed width, the joints running true, the stones to be laid with joints not exceeding 6 mm. (¼″) thick and to be evenly and firmly bedded flush in mortar on the concrete and no hollow left, side to be dressed true and as per shape at least half the depth from the face, preparing the lime mortar in lime miller, watering and all paving work when handed over to be perfectly clean and free from all mortar stains etc. complete.flooring for ghat and parking NON SSR R.A. No.151

Providing and fixing Stone Paving, First Sort in lime mortar 1:1, with size of stone 0.45 m. x 0.30 m. x 0.15 m., as per detailed specifications and drawings or as directed including all stone slabs to of approved quality, hard, even, sound, durable and uniform thickness, the stones to be very finely chisel-dressed on the surface and the course to be of prescribed width, the joints running true, the stones to be laid with joints not exceeding 6 mm. (¼″) thick and to be evenly and firmly bedded flush in mortar on the concrete and no hollow left, side to be dressed true and as per shape at least half the depth from the face, preparing the lime mortar in lime miller, watering and all paving work when handed over to be perfectly clean and free from all mortar stains etc. complete. NON SSR R.A. No.149

Providing/Re-setting Ashlar Fine Masonry of reuse-stones in lime mortar 1:1 in superstructure as per detailed specifications and drawings or as directed including the stones shall be set in fine mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course, the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete. NON SSR R.A No.12

Providing Ashlar Rough-tooled Masonry of trap / granite stones in lime mortar 1:1½ with size of stone 0.45m. x 0.30 m. x 0.23 m. in superstructure as per detailed specifications and drawings or as including the stones be of approved quality, colour, hard and free from defect of any kind, the faces exposed to view shall have fine dressed chisel draft, 25 mm. (1″) wide all around the edges and rough tooled between the drafts, and on all beds or joints, which shall not exceed 6 mm. (¼″), the stones shall be set in mortar, the stone shall be laid in regular course not less than 30 cm. (12″) in height averaging 4½ c. ft., the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete. NON SSR R.A. No15

Providing Block In Course Masonry of trap / granite stones in lime mortar 1:1½ with size of stone 0.45m. x 0.30m. x 0.23 m. in superstructure as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, the face of stones shall be rough-tooled, rustic (with or without chisel draft, except at quoins), or chamfered as specified, the beds and joints of all ashlar stones to be dressed perfectly true, square and full, headers shall not be less in length than breadth of ashlar stone plus 45 cm. (1ꞌ6″), the stones shall be set in mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course not less than 17.5 cm. (7″) in height, the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete.NON SSR 39

Providing Block In Course Stone Steps of trap / granite stones in lime mortar 1:1½ with size of stone 0.45 m x 0.30m x 0.23m. as per detailed specifications and drawings or as directed the stones be of approved quality, colour, hard and free from defect of any kind, the stones shall be of exact size and shape, the shall be rough-tooled on exposed surface, holes for balusters should be cut in the steps before they are laid, each stone shall rest at least 3.8 cm. (1½″) on that below it, the beds or joints being in no case more than 3 mm. (⅛″), preparing the lime mortar in lime miller, watering and all steps work when handed over to be perfectly clean and free from all mortar stains etc. complete.NON SSR R.A. No.65

Providing and laying Cast in situ/Ready Mix cement concrete M-15 oftrap/ granite/quartzite/gneiss metal for coping to plinth or parapet, moulded orchamfered as per drawing or as directed including steel centering, plywood/ steelformwork compacting, roughening them if special finish is to be provided, finishinguneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3plaster is considered for rendering uneven and honeycombed surface only. Newly laidconcrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.) With fine aggregate (Crushed sand VSI Grade).SSR 2022-2023 Item No. 24.16 Pg No.177

Providing Semi-circular Coping Cut-stone Second Sort, 22.5 cm. (9″) height and 52.5 cm. (1ꞌ9″) wide of trap / granite stones in lime mortar 1:1½ with size of stone0.760 m. x 0.560m. x 0.2 m. as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, the stone shall be dressed full or to template, exposed face of the stones shall be fine rough tooled, semi-circular and all joints shall be in line and close and not more than 3 mm. (⅛″) thick, preparing the lime mortar in lime miller, scaffolding, watering and all coping work when handed over to be perfectly clean and free from all mortar stains etc. complete. NON SSR 59

Providing and fixing mild steel grill work for windows, ventilators etc. 20 Kilogram/ One Square Metre as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete.SSR 2022-2023 Item No. 40.01 Pg No.264

Providing Ashlar Fine Masonry of trap / granite stones for TADKHADA(BASESTONE) in lime mortar 1:1 with average size of stone 0.60 m. x 0.60 m. x 0.60 m. in superstructure as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, dressing every stones fine tooled on all beds, joints and faces, full true if the surface are plane or to uniform curves or twists if required, the stones shall be set in fine mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course not less than 30 cm. (12″) in height averaging 4½ c. ft., the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete For Stone curved shape chajja for Temple. NON SSR 11

Providing Ashlar Fine Masonry of trap / granite stones for Columns/Ganesh Patti/Lintel/Chandrashila/Ardha-Chandrashila in lime mortar 1:1 with average size of stone 0.6 m. x 0.6 m. x 2.70 m in superstructure as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, dressing every stones fine tooled on all beds, joints and faces, full true if the surface are plane or to uniform curves or twists if required, the stones shall be set in fine mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course not less than 30 cm. (12″) in height averaging 4½ c. ft., the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete For Stone curved shape chajja for Temple. NON SSR 11

Providing Ashlar Fine Masonry of trap / granite stones for Beams/Ganesh Patti/Lintel/Chandrashila/Ardha-Chandrashila in lime mortar 1:1 with average size of stone 0.50 m. x 0.50 m. x 2.70 m. in superstructure as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, dressing every stones fine tooled on all beds, joints and faces, full true if the surface are plane or to uniform curves or twists if required, the stones shall be set in fine mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course not less than 30 cm. (12″) in height averaging 4½ c. ft., the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete For Stone curved shape chajja for Temple. NON SSR 11

Providing Ashlar Fine Masonry of trap / granite stones for CIRCULAR BRACKET in lime mortar 1:1 with average size of stone 0.75m. x 0.40 m. x 0.30 m. in superstructure as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, dressing every stones fine tooled on all beds, joints and faces, full true if the surface are plane or to uniform curves or twists if required, the stones shall be set in fine mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course not less than 30 cm. (12″) in height averaging 4½ c. ft., the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete For Stone curved shape chajja for Temple. NON SSR 11

Providing Ashlar Fine Masonry of trap / granite stones for FOURWAY BRACKET/RECTANGULAR BRACKET in lime mortar 1:1 with average size of stone 0.9m. x 0.90 m. x 0.40 m. in superstructure as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, dressing every stones fine tooled on all beds, joints and faces, full true if the surface are plane or to uniform curves or twists if required, the stones shall be set in fine mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course not less than 30 cm. (12″) in height averaging 4½ c. ft., the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete For Stone curved shape chajja for Temple. NON SSR 11

Providing Ashlar Fine Masonry of trap / granite stones for KARNSHILA CAP,KARNSHILA STONES in lime mortar 1:1 with average size of stone 1.85m. x 0.90m. x 0.30 m. in superstructure as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, dressing every stones fine tooled on all beds, joints and faces, full true if the surface are plane or to uniform curves or twists if required, the stones shall be set in fine mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course not less than 30 cm. (12″) in height averaging 4½ c. ft., the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete For Stone curved shape chajja for Temple. NON SSR 11

Providing Ashlar Fine Masonry of trap / granite stones for SLAB in lime mortar 1:1 with average size of stone 0.6m. x 0.60 m. x 0.50 m. in superstructure as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, dressing every stones fine tooled on all beds, joints and faces, full true if the surface are plane or to uniform curves or twists if required, the stones shall be set in fine mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course not less than 30 cm. (12″) in height averaging 4½ c. ft., the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete For Stone curved shape chajja for Temple. NON SSR 11

Providing Ashlar Fine Masonry of trap / granite stones for CHAJJA STONES in lime mortar 1:1 with average size of stone 1.3m. x 0.60m. x 0.22 m. in superstructure as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, dressing every stones fine tooled on all beds, joints and faces, full true if the surface are plane or to uniform curves or twists if required, the stones shall be set in fine mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course not less than 30 cm. (12″) in height averaging 4½ c. ft., the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete For Stone curved shape chajja for Temple. NON SSR 11

Providing Ashlar Fine Masonry of trap / granite stones for KAKSHASHAN in lime mortar 1:1 with average size of stone1.85m. x 0.90m. x 0.30 m. in superstructure as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, dressing every stones fine tooled on all beds, joints and faces, full true if the surface are plane or to uniform curves or twists if required, the stones shall be set in fine mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course not less than 30 cm. (12″) in height averaging 4½ c. ft., the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete For Stone curved shape chajja for Temple. NON SSR 11

Carving ornamental work including moulding, grove, chisseling & dresing the same part with fine finishing as per existing/similar type of work of on the stone surface of any type & size or as directed by engineer in charge etc. complete. The charges for chisscling & dressing on stone surface for govering at the stone surface after chisling a fine surface rate for as per market rate.

Caving ornamental work on surface including moulding, grove, chisseling & dresing the same part with fine finishing as per existing/similar type of work of on the stone surface of any type & size or as directed by engineer in charge etc. complete.The charges for chiseling & dressing on stone surface for ornamental carving work surface etc. as per existing design. pattern and form as directed by engineer in chargeRates as per R.A. No. 29

Providing Soil Bag Support to the monument with contractor´s soil in proper layers carefully as directed by Engineer in-charge including filling, tying and conveying the bags, removing the soil bags after work up to a distance of 50 meter beyond the monument area and cleaning the site etc. complete.NONSSR206

Providing and laying cast in situ 1:1:4 Lime Concrete of broken brick metal for coping or waterproofing as per detailed specifications and drawings or as directed including centring, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required, with fine aggregate, preparing the lime mortar in lime miller and then mixing with coursed aggregate or surkhi in drum mixer, the concrete must be bitten for two days with pouring water as per specifications, scaffolding, watering and all concrete work when handed over to be perfectly clean and free from all mortar stains, etc. complete. NON S.S.R. R.A.6

Providing and fixing frame with / without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete SSR 2022 - 23 Page No.245 Item No.39.01

Providing and fixing Country cut teak wood double or single leaf panelled shutters, 35 mm thick style top and freze rail 95 x 35 thick with lock and bottam rail 195 x 25 mm thick and panels without ventilator as per detailed drawing excluding the door frame, stainless steel fixtures and fastening and finishing the wood work with oil painting 3 coats complete SSR 2022 - 23 Page No.246 Item No.39.08

Providing and applying melamine polish of required finish to the wood work byspray machine including knotting and preparing the even surface by scraping,applying French polish , scaffolding if required etc. complete.Note:The work to be executed on prior approval of Superintending Engineer will be necessary. SSR 2022 - 23 Page No.222 Item No.34.09

Providing and laying in situ /Ready Mix cement concrete M-20 of trap / granite/quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations,grillage and footings of R.C.C. columns and steel stanchions etc. including bailingout water, Steel centering formwork, laying/pumping cover blocks, compaction andcuring roughening the surface if special finish is to be provided (Excluding reinforcementand structural steel) etc. complete, with fully automatic micro processor based PLC withSCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc.complete. With fine aggregate (Crushed sand VSI Grade)SSR 2022 - 23 Page No.178 Item No.25.11

Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap /granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing oras directed including steel centering, formwork, cover blocks, laying/pumping, compactionfinishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness togive a smooth and even surface or roughening if special finish is to be provided and curing etc. complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)SSR 2022 - 23 Page No.179 Item No.25.31

Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, complete.SSR-2022-23 Item.No.26.33 Pg. No.188

Providing and fixing mild steel grill gate with angle iron frame 65mm x 65mm x 10mm with iron bars at 150mm C/C and diagonal flats as per the detailed drawing including hinges, pivot block locking arrangement, welding riveting and oil painting of three coats of approved shade Weight of gate 35 Kilogram/Smt.SSR 2022 - 23 Page No.294 Item No.44.10

Providing 12 mm. thick Rough Cast Lime Plaster and 10 mm thick in double coat in lime mortar 1½:1 and lime putty fine coat on last layer in plinth, as per detailed specifications and drawings or as directed including all joints in masonry and brick work are to be racked out to a depth of at least 20 mm. and the wall to be washed with fresh water and thoroughly wetted for six hours before plastering, the plaster to be applied in an even and uniform coat well pressed in to the joints and to be well beaten for 1½ days with hand tappers, the plaster should also be well sprinkle during the proses of beating with a mixture of 1.10 jaggary and 640 gram pulp of wood apple (Belfruit) in 90 to 135 litre of water, the plaster being wetted occasionally with fresh water while the beating is in progress, all exposed angles and junctions with door frame to be carefully finished, all mouldings shall be worked true to template and drawn neat, clean and level, soffits of arches must true arch of circle, preparing the lime mortar in lime miller with 1.60 kg Gugal (a kind of fragrant gum) and 960 gram chopped hemp (fibre of bhendi or tag ) per cubic metre of lime mortar as a bonding material, of lime as a bonding material, watering and all work when handed over to be perfectly clean and free from all mortar stains etc. complete.NONSSR RA142

Stucco work in lime, surkhi and sand (1:1:1) as per traditional practices and design, the mortar should be prepared by grinding mill only. The thickness varies from 10mm to 100mm as per design.NON SSR 2022 - 23

Providing and applying integral fine coat, with addition of colour pigments, as paint to the plainlime stucco plaster in 2 layers, including scaffolding, curing, all leads and lifts, etc. complete. 1) The first coat to be laid is a mixture of fine lime and white washing lime in proportion of 2:1,made smooth with wooden rubbers and very lightly beaten. 2)The finishing coat consisting of fine lime, white washing lime, mixed with the appropriate pigment in 1:2:1 proportion is to be applied and well polished with trowels. .NON SSR 2022 - 23

Disposing of dismantling materials of R.C.C./ stone / brick masonry / derbies, excavated material / soil / murum / rubbish material or vegetation / grass / shrubs etc., from work site beyond the 5km. SSR 2023-24 STATEMENT C1 PG NO.459

Providing and fixing Required Size Granite plate engraving 10 cm. Height letter, figures including painting the lefters/figures with approved colour and shade complete SSR 2022-23 Page No.294 Item No.44.12

Supplying and erecting Solar Street Light Non SSR

Providing and fixing precast benches of size 1.80x0.75m with two leg support of thickness 75mm, M20 Concrete with situ finish with backrest to be placed above the platform edjes lines/periphary etc. Complete in all respects as per the Design & Instructions of the Engineer Incharge including all taxes, transportation charges, loading, unloadning etc, complete. Basic Rate (as per market rate)NON SSR

Preparing and carrying out videography, Documentary & Shooting of still photographs of Extra copies - 5" X 7" Size outdoor and indoor of roads, bridges, other structures and programme, including preliminarys survey, still shots moving shooting, necessary board for video shooting hiring of vehicle, equipment for video shoot­ing, transportation of all equipment, persons, required for shooting, lighting arrangement as may be necessary, editing, mixing, titling, lettering, sounding including cost of coloured cassette of approved quality etc. complete NON SSR

Book Designing, Publishing and Printing: The work involves printing of a book / guidebook on the fort / monuments and its various aspects, which would provide authentic and precise tourism oriented information. This work involves important photographs of the site, art objects, antiquities, inscriptions etc., which would be useful for educating the masses of the rich cultural heritage of the site, region and state. providing 100 pages coloured books as directed by engineer in charge / ADA Non SSR