Gondwana University Tender

Modular Workstation 900Wx600D SIDE BY SIDE (non sharing) (quantity is given cosidering number of seats) Supplying & placing in position of SIDE BY SIDE of size 900W X 600D Modular desk based system with 1200mm ht. legs are fabricated by Argo Shield & have a rectangular shape. legs are available for work top level 750 mm from base. Wire Tray with integrated power box & switch plate (8+3 Anchor Roma). Provision of groomet hole. modesty: shall be made 18mm thick Prelam particle board confirming to IS 12823: 1990 with 2mm thick PVC lipping glued with glue confirming relavant IS code. Modesty shall be available in height of 450mm. HR Screen: 18mm thk T mold Fabric screen on studs is providing on table top. Worktop: 25mm thk prelaminated partical board with pvc lipping. All metal components should be of MS CRCA of Tata Steel or Sail or Jindal Steel and pre treated with zinc phosphating in 8 tank porcess and then powder coated with epoxy polyster powder coating of Kansai Nerolac Paints or Asian Paints. Test reports conforming to relevant ISI codes for raw material, powder coating/ anodizing with anti-rust surface treatment inclusive of method of tests i.e. Dry film/ coating thickness, Finish, Gloss 60°, Colour retention, Scratch hardness, Impact resistance test, DFT measurement, Salt spray test, Adhesion Cross cut test. CPU Trolley -Metal CPU trolley with castors. - Metal Keyboard Pull out Tray. Goods should have low VOC emission. The material to be supplied from ISO 9001:2015, ISO 14001 :2015, ISO 45001 : 2018, certified Manufactures.

3 Drawer Free standing Pedestal PRELAM PEDESTAL 3 MS(2B+1F) DRAWER WITH CASTOR ,SINGLE LOCK @ 400WX450DX670H FOR WS & CABIN 8 NOS Pedestal Top- Shall be made 18mm thick Prelam (OSL) particle board confirming to IS 12823: 1990 with 2mm thick PVC lipping glued with Kliberit-779.6 glue. Table top is under goes from distributed load test for deflection by applying 0.027kg/mm load on Top and concentric load test by applying 90kg load on weaker section Pedestal body- Pedestal LH side panel RH side panel and back shall be made up of 18mm thick Prelam (OSL) particle board confirming to IS 12823: 1990 with 2mm thick PVC lipping glued with Kliberit-779.6 glue. Side panel - Bottom and Top panel to be assembled with the help of wooden dowel - knock down fittings Drum with screw and corner fittings to ensure stability of box structure formed. Top - Side Panel - Bottom with proper 9mm thick grooving done near to back side edge for fitment of back panel .9 mm step grooving is done on Back panel and it slide into the side panel groove and fix by applying the glue on the edges. Pedestal body shall be fitted to the ground with M6 levelers or Nylon caster 40mm. Drawer- Shall be made up of be made of 0.7 mm thick CRCA sheet confirming to IS 513: 2008 with powder coated finish up to 50 to 60 Micron and Drawer facia made up of 18mm thick Prelam (OSL) particle board confirming to IS 12823: 1990 with 2mm thick PVC lipping glued with Kliberit-779.6 glue. C type SS brush finish handle is used in both the shutter of 96mm CD (center to center distance of handle hole). Box drawers mounted on 27x400mm Telescopic slide with 3/4 extension and File Drawer mounted on 37x400mm Telescopic slide with full extension. Generally 2 types of standard drawer are offered Box drawer in 352x400x70mm and File drawer in 352x400x 245mm. Provision of centralize locking for all the drawers. Generally Hettich make multi drawer lock system is offered.

Staff Chair Supplying & placing in position of chairs, Seat assembly: the seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood , upholstered with fabric upholstery covers and moulded polyurethane foam. back assembly: the back asembly. should be made of powder coated (oft 40-60 microns)tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. ms erw tube designed with contoured lumbar support for extra comfort. the back should be upholstered using double layer spacer mesh fabric with high tenacity yarn. back size : 46.5 cm. (w) x 60.5cm. (h)high resilience (hr) polyurethane foam: the hr polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression.armrests: the one-piece armrests should be injection moulded from black co-polymer polypropylene. tubular frame: the powder coated (dft 40-60.microns) tubular frame should be cantilever type & made of ø2.54 ±0.03cm. x 0.2 ±0.016cm thick m.s.e.r.w. tube.Back: (W)46.5 cm x (H)60.5cm,Seat : (W)47.0cm x (D) 48.0cm. The material to be supplied from ISO 9001:2015, ISO 14001 :2015, ISO 45001 : 2018, certified Manufactures.

Executive Desk - Type 1(Executive Main Table+ Side Table+Pedestal+Back Unit) Supplying & placing in position of work desk, The Main table shall be of size 2400 Width mm x 900 mm Depth x 750 mm height. Top surface of the table shall made up of MDF (Medium density fibre ) board duly finished with Veneer and final coating of PU. The Main desk should contain in built key board pull out tray for keeping keyboard of computer. The front modesty panel of the table shall be made up of MDF board of size 1640 mm x 600 mm x 16mm which shall also be duly finished with Veener and PU coating. For personal storage one mobile pedestal (3 drawer unit) shall be provided of size 510 mm Width x 635 mm Height and 445 mm Depth. The storage pedestal shall also be made up of MDF duly finished with veener & final coating of PU. The Side Table shall be of size 1200mm Width x 443 mm Depth x 650 mm Height. The side unit shall be made up of MDF board duly finshed with Veneer and final finish by PU Coating. The design of the side unit shall be such that it can be placed on either side of the main table. The side unit shall contain open space for keeping cpu in extreme right side, one closed storage shutter at extreme left end & open space in the middle with one shelf for keeping files. The thickness of the top of the side unit shall be 25mm. The Size of the Back unit shall be 2210 mm width x 410 mm Depth x 2000mm height. The back unit shall be made up of MDF board duly finished with veneer & final finish by PU coating. Below storage shall be provided with wooden shutters & the upper left & right side of the back unit shall also be provided with wooden shutters. The middle 3 door shutters should be of glass of minimum 5mm thick for display purpose. The hardness of the PU coating shall be 1.5H. The material to be supplied from ISO 9001:2015, ISO 14001 :2015, ISO 45001 : 2018, certified Manufactures

Executive Desk - Type 2 (Executive Main Table+ Side Table+Pedestal) Supplying & placing in position of work desk, Main table + side table + Pedestal with size of 2100 Wx2250Dx750H in that Main Table of 2100Wx1050Dx750H, Side Table-1200Wx500Dx750 . Pedestal- 472Wx500D. Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire management Secondary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconfirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming toIS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedestal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metalPanel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism.Handles are provided for ease of opening.Pedestals are provided with lock for security. The material to be supplied from ISO 9001:2015, ISO 14001 :2015, ISO 45001 : 2018, certified Manufactures.

Executive Desk - Type 3 (Executive Main Table+ Side Table+Pedestal) Supplying & placing in position of work desk, The main desk of shall be of size 1800 Width mm x 900 Depth mm x 750 Height mm.The table top shall be 25 mm thick MFC (Melamine Faced Chipboard) also there should be 30 mm MDF (Medium density fiberboard) black pad.The modesty panel shall be of 18 mm thick MFC (Melamine faced chipboard).The leg of the main desk shall be of 25 mm MFC plus 30 mm MDF right and left pad. The return desk/side table size shall be 1200 Width mm x 600 Depth mm x 730 Height mm.The top panel shall 25 mm thick MFC ( Melamine Faced Chipboard) .The Modesty panel shall be 18 mm thick MFC coated. The leg of the return desk shall be 25 mm thick MFC (Melamine faced chipboard) plus the right and left pad should be 30 mm thick MDF (medium density fiber ) coated. The Mobile Pedestal size shall be 400 Width mm x 560 Depth mm x 560 Height mm.The top panel shall be 25 mm thick MFC ( Melamine Faced Chipboard) plus all the other panels shall be 18 mm thick coated with MFC (Melamine Faced Chipboard). In Mobile pedestal all other panels shall be of 18 mm thick MFC (Melamine Faced Chipboard).In Mobile pedestal lock and Castors shall be Provided. The handle shall be of Metal. The material to be supplied from ISO 9001:2015, ISO 14001 :2015, ISO 45001 : 2018, certified Manufactures

High Back Revolving Chair Supplying & placing in position of high back chairs ,Leatherite Upholstery, Chrome Finished Fixed Arms, 4 Position Locking, Anti Shock-Synchro Tilt Mechn, Die-Cast Alumium Pedestal, Bk Ht Adj, Auto-Return Mechanism for Conf Chairs. the seat should be made up of hot pressed moulded reconstituted wood of 1.2±0.1cm thickness and back should be two part injection moulded plastic. seat sub assembly size:49.0cm (w) x 49.5cm (d) back sub assembly size: (high back): 46.0 cm (w) x 57.0 cm (h)head rest sub assembly size: 26.0cm (w) x 12.0 cm (l) the hr polyurethane foam should be moulded with density = 45 kg/m³ and hardness load 16 ± 2 kgf for 25% compression the armrests should be pressure die casted in polished hed aluminum with pp arm tops the synchronized mechanism should be designed with the following features: • 360° revolving type. • seat/back tilt ratio of 1:3. • side tilt tension adjustment knob can be operated while taking back support for better judgment of comfort. • back tilt with 4 position locking. the pneumatic height adjustment has an adjustment stroke of 10.0 ±0.3cm. the backrest should be connected to the mechanism with a drop-lift mechanism which can be adjusted in the range of 7.0±0.5cm for the comfortable back support to suitable individual need the pedestal should be pressure die cast polished aluminium and fitted with 5 nos. twin-wheel castors. the pedestal should be 65.0±0.5cm.pitch-centre-dia.(75.0 ±1.0cm. with castors) the twin wheel castors should be injection moulded in black polypropylene The material to be supplied from ISO 9001:2015, ISO 14001 :2015, ISO 45001 : 2018, certified Manufactures

MID Back Revolving CHAIR Supplying & placing in position of mid back chairs, Leatherite Upholstery, Chrome Finished Fixed Arms, 4 Position Locking, Anti Shock-Synchro Tilt Mechn, Die-Cast Alumium Pedestal, Bk Ht Adj, Auto-Return Mechanism for Conf Chairs. 1. seat/back assembly: the seat should be made up of hot pressed moulded reconstituted wood of 1.2±0.1cm thickness and back should be two part injection moulded plastic. seat sub assembly size: 49.0cm (w) x 49.5cm (d) back sub assembly size: (mid back): 45.0 cm (w) x 49.0 cm (h) . high resilience (hr) polyurethane foam: the hr polyurethane foam should be moulded with density = 45 kg/m³ and hardness load 16 ± 2 kgf for 25% compression. armrests : the armrests should be pressure die casted in polished hed aluminum with pp arm tops. synchro mechanism : the synchronized mechanism should be designed with the following features: • 360° revolving type. • seat/back tilt ratio of 1:3. • side tilt tension adjustment knob can be operated while taking back support for better judgment of comfort. • back tilt with 4 position locking. pneumatic height adjustment : the pneumatic height adjustment has an adjustment stroke of 10.0 ±0.3cm. adjustable back support: the backrest should be connected to the mechanism with a drop-lift mechanism which can be adjusted in the range of 7.0±0.5cm for the comfortable back support to suitable individual need. pedestal assembly: the pedestal should be pressure die cast polished hed aluminium and fitted with 5 nos. twin-wheel castors. the pedestal should be 65.0±0.5cm.pitch-centre-dia.(75.0 ±1.0cm. with castors). twin wheel castors:the twin wheel castors should be injection moulded in black polypropylene. The material to be supplied from ISO 9001:2015, ISO 14001 :2015, ISO 45001 : 2018, certified Manufactures.

High Back Chair Supplying & placing in position of high back chairs, 4 Position Locking, Soft touch PU Arms, Chrome-Plated arms & Pedestal, Adj Backrest. seat/back assembly: the seat should be made up of 1.2 ±0.1cm. thick hot pressed plywood upholstered with fabric or synthetic leather and moulded polyurethane foam. the back should be made up 1.2 ±0.1cm. thick hot pressed plywood and upholstered synthetic leather upholstery covers and moulded polyurethane foam. the back ply and foam should be designed with contoured lumber support for comfortable seating posture.back size 48cm.(w) x 76.0cm.(h) seat size 51.0cm.(w) x 48.0cm.(d) high resilience (hr) polyurethane foam: the hr polyurethane foam for seat and back should be moulded with density = 45 +/-2 kg/m³ and hardness load 16 ± 2 kgf for 25% compression.armrests :the armrest top should be made of moulded polyurethane (p.u) and mounted on to a drop lift height adjustable type m.s. tubular armrest support chrome plated. the armrest height should be adjustable up to 6.5±0.5cm. in 5 steps & also has swivel adjustment of 22º±2° on both sides. knee tilt synchro mechanism with seat depth adjustment mechanism: the mechanism should be designed with the following features: • 360° revolving type., • single point control., • front pivot for tilt with feet resting on ground ensuring more comfort. • tilt tension adjustment. • 4-position locking with anti-shock feature., • seat back tilting ratio of 1:2 • seat depth adjustment of 6.0 ±0.5cm. can be locked in 6 positions adjustable backrest: the backrest consshould be ts of a sliding up down mechanism, which can be adjusted in the range of 7.5±0.5cm. and can be locked in 4 pneumatic height adjustment: the pneumatic height adjustment has an adjustment of 9.0 ±0.3cm.pedestal assembly: the pedestal should be fabricated from 0.2 ± 0.02 cm thick hr sheet ( should be : dd 1079 / hr skin pass ), chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. the pedestal should be 66.0±0.5cm. pitch-center dia. (76.0±1.0 cm with castors). twin wheel castors the twin wheel castors should be injection moulded in black nylon. The material to be supplied from ISO 9001:2015, ISO 14001 :2015, ISO 45001 : 2018, certified Manufactures

Visitor Chair Supplying & placing in position of low back chairs Upholstered with synthetic leather, High resilience Polyurethane foam, Fixed armrests, Fixed backrest,Leg frame assembly. seat/back assembly: the seat should be made up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with fabric or synthetic leather and moulded polyurethane foam. the back should be made up 1.2 ±0.1cm. thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. the back ply and foam should be designed with contoured lumber support for comfortable seating posture. mid back size 48.0cm.(w) x 64.5cm.(h) seat size 51.0cm.(w) x 48.0cm.(d)high resilience (hr) polyurethane foam: the hr polyurethane foam for seat and back should be moulded with density = 45±2 kg/m³ and hardness load 16 ± 2 kgf for 25% compression. armrests:the armrest top should be made of moulded polyurethane (p.u) and mounted on to a fixed type m.s. tubular armrest support which should be chrome plated. the arm support has static vertical adjustment of ±1.5±0.05cm.fixed backrest: the backrest consshould be ts of a fixed type mechanism i.e. no back up/down adjustment.leg frame assembly: the leg frame welded assembly should be chrome plated, made from 3.5 ±0.03cm. x 1.5 ±0.02cm. x 0.16 ±0.0128cm. thk elliptical m.s. erw tube and provided with a base plate for seat fixing. The material to be supplied from ISO 9001:2015, ISO 14001 :2015, ISO 45001 : 2018, certified Manufactures

Mid Back Conference Chair Supplying & placing in position of high back chairs , Upholstered with synthetic leather, High resilience Polyurethane foam, Fixed armrests, Front pivot synchro mechanism, 360 degree evolving type, Single point control, Tilt tension adjustment, 4 position locking with anti shock feature, seat back tilting ratio of 1:2, Fixed backrest, Pneumatic height adjustment, Pedestal assembly with twin wheel castors. seat/back assembly: the seat should be made up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with fabric or synthetic leather and moulded polyurethane foam. the back should be made up 1.2 ±0.1cm. thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. the back ply and foam should be designed with contoured lumber support for comfortable seating posture.back size 48cm.(w) x 64.5cm.(h)seat size 51.0cm.(w) x 48.0cm.(d) high resilience (hr) polyurethane foam: the hr polyurethane foam for seat and back should be moulded with density = 45 +/-2 kg/m³ and hardness load 16 ± 2 kgf for 25% compression.armrests the armrest top should be made of moulded polyurethane (p.u) and mounted on to a fixed type m.s. tubular armrest support chrome plated. the arm support has static vertical adjustment of ±1.5±0.05cm. front pivot synchro mechanism: the mechanism should be designed with the following features: • 360° revolving type. • single point control. • front pivot for tilt with feet resting on ground ensuring more comfort. • tilt tension adjustment. • 4-position locking with anti-shock feature. • seat back tilting ratio of 1:2. fixed backrest :the backrest consshould be ts of a fixed type mechanism i.e. no back up/down adjustment. pneumatic height adjustment :the pneumatic height adjustment has an adjustment of 9.0 ±0.3cm. pedestal assembly:the pedestal should be fabricated from 0.2 ± 0.02 cm thick hr sheet ( should be : dd 1079 / hr skin pass ), chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. the pedestal should be 66.0 ±0.5cm. pitch-center dia. (76.0 ±1.0cm. with castors). twin wheel castors: the twin wheel castors should be injection moulded in black nylon. The material to be supplied from ISO 9001:2015, ISO 14001 :2015, ISO 45001 : 2018, certified Manufactures

2 Seater sofa Supplying & placing in position of 2 Seater Sofa pf seat foam: the seat should be made of pu foam with density 32 ± 2 kg/cu.mtr having an additional top layer of j pu foam with density 28 ± 2 kg/cu. seat should be upholstered with fabric or leatherette. 2) back foam: the back should be made of pu foam with density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 23±2 kg/cu. mtr, upholstered with fabric or leatherette understructre : understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood ocp-qlta-pl14-18 4. dia 4mm zigzag spring assembly should be mounted in understructure for support and additional cushioning purpose leg assembly: it should be a welded assembly made in stainless steel (grade ss 202) tube & plate.Width (W): 146.0 CM. Depth (D): 92.0 CM. Height (H): 82.0 CM. Seat Height (SH): 45.0 CM. All metal components should be of MS CRCA of Tata Steel or Sail or Jindal Steel and pre treated with zinc phosphating in 8 tank porcess and then powder coated with epoxy polyster powder coating of Kansai Nerolac Paints or Asian Paints. Test reports conforming to relevant ISI codes for raw material, powder coating/ anodizing with anti-rust surface treatment inclusive of method of tests i.e. Dry film/ coating thickness, Finish, Gloss 60°, Colour retention, Scratch hardness, Impact resistance test, DFT measurement, Salt spray test, Adhesion Cross cut test. Goods should be supplied in knocked down construction and should have low VOC emission. The material to be supplied from ISO 9001:2015, ISO 14001 :2015, ISO 45001 : 2018, certified Manufactures

CORNER TABLE Supplying & placing in position of corner table, Dimantions(+/-5mm)-500mm(w)*500mm(l)*428mm(h)*8 glass thk.Material-Glass of 8mm thk tempered,solid rubber wood legs & frame ,MS sheet with appropriate zinc coating and spray painting confirming to relevant IS code requirement as bottom shelf. The material to be supplied from ISO 9001:2015, ISO 14001 :2015, ISO 45001 : 2018, certified Manufactures

Centre Table Supplying & placing in position of side table, Dimantions-600mm(w)*1000mm(l)*428mm(h)**8mm(glass thk).Material=Glass of 08mm thk tempered,solid rubber wood legs & frame ,MS sheet as bottom shaf . Decoration materials- PU coateing to rubber wood parts clear glass. The material to be supplied from ISO 9001:2015, ISO 14001 :2015, ISO 45001 : 2018, certified Manufactures

4 - Door Personal Locker (set having 1 main and 2 addon units-Total number of lockers = 144 nos. [(1main x 4 lockers + 2 add on x 4 lockers ) x (12 nos of mudule) = 144 lockers} Supplying & placing in position of Overall size of 4 - Door PLU + Lkr (Base) shall be 380mm(W)x450mm(D)x1830mm(H). (set consisting of 1 Main Unit + 2 add on Unit) Stackability shall have add - on units that can be stacked width wise to form bank of lockers having common side panel. Locking shall have 10 Lever cam lock with lock lever plus option of hasp arrangement . Material shall be CRCA 0.6 mm thickness . Construction shall be Rigid Knockdown construction , shelf shall be uniformly distributed load capacity per each shelf level is 35 Kg maximum . Finish shall be epoxy polyester powder coated to the thickness of 50 microns . Handle/Label holder shall be Aesthetically appealing Snap fit ABS plastic handle . Ventilation shall be attractive punched pattern for ventilation . All metal components should be of MS CRCA of Tata Steel or Sail or Jindal Steel and pre treated with zinc phosphating in 8 tank porcess and then powder coated with epoxy polyster powder coating of Kansai Nerolac Paints or Asian Paints. Test reports conforming to relevant ISI codes for raw material, powder coating/ anodizing with anti-rust surface treatment inclusive of method of tests i.e. Dry film/ coating thickness, Finish, Gloss 60°, Colour retention, Scratch hardness, Impact resistance test, DFT measurement, Salt spray test, Adhesion Cross cut test. Goods should be supplied in knocked down construction and should have low VOC emission. The material shall be supplied from ISO 9001:2015, ISO 14001 :2015, ISO 45001 : 2018, certified Manufactures

wardrobe With 4 Shelves Supplying & placing in position of lockable wardrobe With 4 Shelves shall have an overall size of 900mm(W)x450mm(D)x1830mm(H) . The construction shall be rigid knock down construction and Material used shall be prime quality CRCA steel - panels from 0.6 mm thick & front frame . Shelf shall be 0.8 mm thick .Configuration (Door) shall be full height steel hinged door . Locking shall be Plastic Recessed Handle cum Cam lock with 3 way locking mechanism with shooting bolt arrangement . Height wise adjustable shelf mounting , Uniformly distributed load capacity per each full shelf shall be 80 Kg maximum . For Plain 4 Nos. of adjustable full shelves . The top shall be metal and Epoxy Powder coated finish to the thickness of 50 microns . All metal components should be of MS CRCA of Tata Steel or Sail or Jindal Steel and pre treated with zinc phosphating in 8 tank porcess and then powder coated with epoxy polyster powder coating of Kansai Nerolac Paints or Asian Paints. Test reports conforming to relevant IS codes for raw material, powder coating/ anodizing with anti-rust surface treatment inclusive of method of tests i.e. Dry film/ coating thickness, Finish, Gloss 60°, Colour retention, Scratch hardness, Impact resistance test, DFT measurement, Salt spray test, Adhesion Cross cut test. Goods should be supplied in knocked down construction and should have low VOC emission. The material shall be supplied from ISO 9001:2015, ISO 14001 :2015, ISO 45001 : 2018 certified Manufactures

Slotted Angle Storag Rack Supplying & placing in position of Slotted Angle Rack Slotted angle- Slotted angle is made up 2mm thick CRCA sheet confirming the IS grade IS 513:2008 coated with final finish consisting of epoxy polyester powder coat of approved color & shade with a Dry Film Thickness of minimum 50 to 60 microns. Angle length is equivalent to the height of the storage which is approx. 1830mm Shelf-Is made up of 0.8mm CRCA sheet confirming the IS grade IS 513:2008. All the four edge is having a bend of 25mm. Shelf is supported by T-Hat in the middle portion. T-hat is made up of 0.8mm CRCA sheet confirming the IS Grade IS 513:2008.Each shelf is having loading carrying capacity of 18kg UDL and total load carrying capacity of unit is 50kg UDL. Finish- The bodies including shelves are given anti-rust surface treatment & are powder coated with epoxy polyester powder. It involves an Oxsilan pre-treatment consisting of Hot water degreasing, cold water rinse I & cold water rinse II, iron phosphate, cold water rinse, and passivation & dry off oven treatment. Final finish consists of epoxy polyester powder coating of approved color & shade with a Dry Film Thickness of 50 to 60 (+\- 5) microns. The material is then oven baked with a controlled temperature of 180 deg.C to 200 deg.C. Fasteners:- Assembly is done with the help of M8 NUT nuts & HEX BOLT M8 X 16.

Conference Table Overall Size: 7600W x 3050D x 740H Supplying & placing in position of Conference Tables of Overall Size: 7600W x 3050D x 740H MODULAR PLT_2 STR MAIN PT (1350 X 600 X 740)- 11 Nos. MODULAR PLT CORNER 90 PT (850 X 850 X 740)- 2 Nos. Work Surface-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Plastic ABS access flap is provided for easy access to wires and cables. Work top is available in various shapes as shown above. Understructure-It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction. Modesty Panel-Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns. Wire Management-An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio,video cables onto worktop and connect devices charger to power socket below worktop. All metal components should be of MS CRCA of Tata Steel or Sail or Jindal Steel and pre treated with zinc phosphating in 8 tank porcess and then powder coated with epoxy polyster powder coating of Kansai Nerolac Paints or Asian Paints. Test reports conforming to relevant IS codes for raw material, powder coating/ anodizing with anti-rust surface treatment inclusive of method of tests i.e. Dry film/ coating thickness, Finish, Gloss 60°, Colour retention, Scratch hardness, Impact resistance test, DFT measurement, Salt spray test, Adhesion Cross cut test. Goods should be supplied in knocked down construction and should have low VOC emission. The material shall be supplied from ISO 9001:2015, ISO 14001 :2015, ISO 45001 : 2018 certified Manufactures,

Conference Table Overall Size: 4900W x 1800D x 740H Supplying & placing in position of modular Conference Tables of Overall Size: 4900W x 1800D x 740H MODULAR PLT_2 STR MAIN PT (1350 X 600 X 740)- 6 Nos. MODULAR PLT 1800W PT- 1 Nos. Work Surface-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Plastic ABS access flap is provided for easy access to wires and cables. Work top is available in various shapes as shown above. Understructure-It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction. Modesty Panel-Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns. Wire Management-An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio,video cables onto worktop and connect devices charger to power socket below worktop. All metal components should be of MS CRCA of Tata Steel or Sail or Jindal Steel and pre treated with zinc phosphating in 8 tank porcess and then powder coated with epoxy polyster powder coating of Kansai Nerolac Paints or Asian Paints. Test reports conforming to relevant ISI codes for raw material, powder coating/ anodizing with anti-rust surface treatment inclusive of method of tests i.e. Dry film/ coating thickness, Finish, Gloss 60°, Colour retention, Scratch hardness, Impact resistance test, DFT measurement, Salt spray test, Adhesion Cross cut test. Goods should be supplied in knocked down construction and should have low VOC emission. The material shall be supplied from ISO 9001:2015, ISO 14001 :2015, ISO 45001 : 2018, Certified Manufacturers

6 Seater Meeting Table1800W X 1150D X 740H Supplying & placing in position of Modular discussion table of overall size 1800W X 1150D X 740H Work top-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access panels provided with soft closing hinges. Understructure-The Under-structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded withmatching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is addedat bottom edges for improving the aesthetics. The product has a knock-down construction.WireManagement-Bottom cabinet with door is provided for flow of wires and cables. Cutout provision below Access flap at four locations for standard 8 module Anchor Roma is provided. Beside each cutout, an additional cutout with plate is provided for mounting Audio Visual Cables (eg.HDMI,VGA-A,etc). The material shall be supplied from ISO 9001:2015, ISO 14001 :2015, ISO 45001 : 2018, certified Manufactures.

6 Seater Meeting Table 1800W X 1150D X 740H Supplying & placing in position of Modular desk based system with Cube legs of SIZE: 1800W X 900D X 750H. Wire Tray with integrated power box & switch plate (8+3 Anchor Roma). Soft closing access flap with brush. Worktop: 25mm thk prelaminated partical board with pvc lipping. All metal components should be of MS CRCA of Tata Steel or Sail or Jindal Steel and pre treated with zinc phosphating in 8 tank porcess and then powder coated with epoxy polyster powder coating of Kansai Nerolac Paints or Asian Paints. Test reports conforming to relevant ISI codes for raw material, powder coating/ anodizing with anti-rust surface treatment inclusive of method of tests i.e. Dry film/ coating thickness, Finish, Gloss 60°, Colour retention, Scratch hardness, Impact resistance test, DFT measurement, Salt spray test, Adhesion Cross cut test. Goods should be supplied in knocked down construction and should have low VOC emission. The material shall be supplied from ISO 9001:2015, ISO 14001 :2015, ISO 45001 : 2018 certified Manufactures

WORKSTATIONS - 1500W X 600D MAIN , 900W X 450D Side Table Supplying & placing in position of WORKSTATIONS - 1500W X 600D MAIN , 900W X 450D Side Table with WOODEN MODESTY + PANEL + REQUIRED HARDWARE..Wire Management- Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. legs Worksurface - Main table recta out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w x 750 mm d and ERU table recta of size 900 mm w x 450 mm d. The material shall be supplied from ISO 9001:2015, ISO 14001 :2015, ISO 45001 : 2018 certified Manufactures

cane Sofa Providing, Supplying and Placing in position of 2 seater cane sofa of Size : 1500W X 900D X 800HT (approx) Sofa body Furniture should be Made Up of High Quality Cane with Natural finish. Frame Material: Cane (additional m.s. framing with appropriate weatherprrof coat should be included to achive strength) Item consist of standard cotton cousion of proper density and thickness, fabric cousion cover, back cousion with cousion cover of colour approved by committee,Item inclusive of all required adheisives, hardwares, polishing/painting with low VOC material of approved shade and other allied item if any confirming to relavent IS Standards etc complete .

cane center Table Providing, Supplying and Placing in position of cane center table of Size 1200m L x600mm W x 450mm H Furniture should be Made Up of High Quality Cane with Natural finish. Frame Material: Cane 8 mm thick clear glass top of size aproprite as per finalized design,inclusice of all gasket fixed to furniture body to hold glass in position. Item inclusive of all required adheisives, hardwares, polishing/painting with low VOC material of approved shade and other allied item if any confirming to relavent IS Standards etc complete .

Cane Corner Table Providing, Supplying and Placing in position of cane corner table of Size 600m L x600mm W x 450mm H Furniture should be Made Up of High Quality Cane with Natural finish. Frame Material: Cane 8 mm thick clear glass top of size aproprite as per finalized design,inclusice of all gasket fixed to furniture body to hold glass in position. Item inclusive of all required adheisives, hardwares, polishing/painting with low VOC material of approved shade and other allied item if any confirming to relavent IS Standards etc complete .

pelmet for curtain (UNIT -SQM) Providing and fixing 20 mm thick Laminated sheet board pelmet box 150 to 200mm wide to doors or window frames including 20 mm dia. Aluminium curtain rod with sockets and finishing with french polishing (without top) etc.complete.

pelmet for indoor AC unit(UNIT -SQM) Providing 18mm plywood boxing to hang indoor unit of hi-wall (split AC unit) air conditioner and to hide cable and drain pipe, capable enough to hold the load of A.C. assembly, finished with laminate of approved shade, including required adhesive, hardware with finish from all side and fixing at location suggested by university

Compactor - compactor Double Faced Mobile Unit Supply and installation of SOS make Compactor Storage System, Main Body: Rigid Knock Down construction made out of 0.8mm thk. CRCA Steel conforming to IS: 513 Grade. Each body block (SFF/SFM/DFM) building consists of 1 Main unit & then Add-on units ( 1, 2, 3, 4 - depending on no. of bays 2, 3, 4 & 5). Each unit has 5 loading levels formed by 4 nos. adjustable shelves. Body units are bolted to undercarriage. Compactor Height from ground is 2080 mm (1980 body + 100 under-structure + 35 channel system). SFF- SINGLE FACE FIX UNIT, SFM- SINGLE FACE MOBILE UNIT, DFM- DOUBLE FACE MOBILE UNIT Finish- The bodies including shelves are given anti-rust surface treatment & are powder coated with epoxy polyester powder. It involves an Oxsilan pre-treatment consisting of Hot water degreasing, cold water rinse I & cold water rinse II, iron phosphating, cold water rinse, passivation & dry off oven treatment. Final finish consists of epoxy polyester powder coating of approved color & shade with a Dry Film Thickness of 50 to 60 (+\- 5) microns. The material is then oven baked with a controlled temperature of 180 deg.C to 200 deg.C. Shelf-It is made of 0.8 thk CRCA steel conforming to IS: 513 Grade or DD. Shelves are having 10 bends & its max load bearing capacity is 70- 80 Kg uniformly distributed per shelf for drive Type of Configuration.. Shelves are mounted on support brackets & shelf level can be adjusted .There are 4 adjustable shelves per body giving 5 loading levels, if no Cradle pair is provided. Shelf Depth for various options 1. Unit Depth(mm)381- Shelf Depth352mm , 2. Unit Depth(mm)457- Shelf Depth428mm. Box Files (Box file size is 275 mm Wide x 345 mm High x 90 mm Thick) can be accommodated in both 381mm and 457mm deep units. Under framing carrier: The Under framing carrier is a welded frame made of HR sheet 3mm thk.suitably fabricated to take the loads based on configuration Sizes of under framing carrier - Single face fix / Last - 915 / 750 x (no. of bays) (Width) X 457 / 381 (Depth) X100 (Height) Finish: The undercarriage, after pre-treatment, is coated with final finish consisting of epoxy polyester powder coat of approved color & shade with a Dry Film Thickness of minimum 50 to 60 microns. Movements of the System: The movement of units is achieved mechanically through a PU Drive wheel and 'Sprocket-Chain-Tensioner' arrangement mounted rigidly onto body side. The torque from hand wheel is transfer to drive shaft via sprocket chain arrangement.. For 2 BAY- each movable under framing carrier is provided with 2 Rollers on the shaft for driving, 2 anti-friction ball bearings for rolling and 4 anti-friction ball bearing for guiding between rails. For 3 BAY- each movable under framing carrier is provided with 3 rollers on the shaft for driving, 3 anti-friction ball bearings for rolling and 4 anti-friction ball bearings for guiding between rails. For 4 BAY, each movable under framing carrier is provided with 4 Rollers on shaft for driving, 4 anti-friction ball bearings for rolling and 4 anti-friction ball bearings for guiding between rails Fittings:- A Centralized locking arrangement is provided through Locking Stiffener mounted onto back of Single Last unit so that it gets locked on channels when all the units are brought together. The Recess handle lock is placed at suitable height. This arrangement occupies a space of 90.0 mm. Each Drive type units have Locking Knob near the Drive wheel for manual locking of individual units when a person is using those units. Knob shall be rotated to unlock position when units are to be moved. After the unit is moved, before entering into aisle for accessing, this knob shall be rotated to lock position. End stoppers are provided at the end of channels to prevent derailment. Fasteners:- The nuts & bolts are galvanized / blackodized / Zn Plated. Rails / Guide Channels: It consists of 'J' section 2 mm thk HR sheet & 25 mm Square bright bar - both connected by screws. Prior to the embedding of the guide channels with the help of rawl plug & screw, the ground has to be in properly leveled condition. compactor Double Faced Mobile Unit Supply, Fitting & Fixing of COMPACTOR 4 BAY / SINGLE FACE FIX UNIT/WITHOUT SHUTTER @ 3660LX381DX2115HT

compactor Single Faced Mobile Unit Supply, Fitting & Fixing of SOS Make COMPACTOR 4 BAY / SINGLE FACE MOBILE UNIT/WITHOUT SHUTTER @ 3660LX381DX2115HT

compactor Single Faced FIX Unit Supply, Fitting & Fixing of SOS Make COMPACTOR 4 BAY / DOUBLE FACE MOBILE UNIT/WITHOUT SHUTTER @ 3660LX762DX2115HT

COMPACTOR FLOOR RAIL Supply, Fitting & Fixing of SOS Make COMPACTOR FLOOR RAIL IN PER FT .