Military Engineer Services Tender

All as per item No.1 here in before but of size 50mm

All as per item No.1 here in before but of size 40mm

All as per item No.1 here in before but of size 32mm

All as per item No.1 here in before but of size 25mm

All as per item No.1 here in before but of size 20mm

M&L for 150mm dia MS ERW pipe heavy grade 'C' Class complete heavy grade class, 'C' with welded ends laid in ducts over the angle iron supports/ fixed on the walls including fittings complete all as specified and directed by Engr-in-Charge. (Note : The item rate is inclusive of cutting to any levels/shapes like elbows, tees, bends etc, welding joints wherever necessary as per the site requirement)

All as per item No. 9 here in before but of size 100mm

All as per item No.9 here in before but of size 80mm

All as per item No.9 here in before but of size 50mm

All as per item No.9 here in before but of size 40mm

All as per item No.9 here in before but of size 32mm

All as per item No .9 here in before but of size 25mm

All as per item No.9 here in before but of size 20mm

Excavation in trenches, n.exc 1.5m wide & n.exc 1.5m in depth for foundation etc in Hard and Dence soil & getting out for laying of cable complete all as specified & directed.

Returning filling in including spreading leveling watering & well ramming in layers n exc. 25cm Cum thick complete all as specified & directed.

Removing of surplus excavated soil to a distance n.exe 50 Mtr and depositing where directed at a level n.exe 1.5 mtr above the starting point complete all as specified & directed.

M & L for construction of brick masonry valve chamber of size 90 cm x 90 cm x 90 cm (internal dimensions) with one brick thick wall in CM (1:4) on 100 mm thick PCC (1:4:8) type D2 using 40 mm graded broken aggregate as in foundation lean concrete, incl. PCC (1:3:6) type C-1 (using 20 mm graded stone aggregate) as in bedding & coping & 10 mm thick cement plaster in CM (1:4) internally & externally upto 15 cm below ground level. Fixing 40 mm x 40 mm x 6 mm angle iron frame all round the chamber with 04 nos of holdfasts 150 mm long made out of 40 mm x 6 mm flat iron embedded in PCC block (1:2:4) type B1 of size 250 mm x 200 mm x 15o mm incl. provision of hinges welded with cover of MS sheet 3 mm thick, MS handle of of suitable size welded with MS cover & suitable locking arrangement incl. padlock & applying two coats of synthetic enamel paint over a coat of red oxide primer incl. necessary excavation & earth work in soft/loose soil complete all as specified and directed

Cutting the existing CI Pipe line any size in position for insertion of new Butterfly valve of size as per ground required directed for tapping out branch connection complerte including joints complete all as specified & directed. (Note :- Butterfly valve excavation to measured and paid separately)

M&L for replacement of Cast iron Butterfly valve of size 150mm dia Class PN 1.6 with SG Iron Dice flanged ends (integrally cast) horizontal type, conforming to IS-14846 (ISI marked) with stainless steel spindle and iron wheel non rising type including jointing material complete such as rubber or fibre board insertion packing rings with requisite numbers of nuts, bolts & washers etc including taking out existing unserviceable valve complete all as specified and directed.

All as per item no 22 here in before but 100mm dia

All as per item no 22 here in before but 80mm dia

S&F in replacement of inlet/outlet forged brass ball valve 20 mm with Y Stainer for FCU, hot water for -25 to 90 degree temperature as per existing, including supply and fixing GI nipple of size 3/4 inch including welding work, cutting the existing rusty unserviceable MS/GI nipple complete including taking out existing unserviceable valve complete all as specified and directed.

S&F and replacement of Inlet/outlet forged brass ball valve 25 mm with Y Stainer for FCU, hot water for -25 to 90 degree temperature as per existing, including supply and fixing GI nipple of size 3/4 inch including welding work, cutting the existing rusty unserviceable MS/GI nipple complete including taking out existing unserviceable valve complete all as specified and directed.

S&F and replacement of Forged steel globe valve, bolted bonnet outside screw & yoke type rising stem for 25mm dia complete including taking out existing unserviceable valve complete all as specified and directed.

All as per item No. 27 here in before but of size 40 mm

All as per item No. 27 here in before but of size 50 mm

Brass flare nuts of size 20/15 mm bore and fix the brass valves/FCUs including taking out existing unserviceable valve complete all as specified and directed.

S&F in replacement of FCU connection flexible pipe 20/16 mm as per existing, complete all as specified and directed. Make- Jindal/Kitetac or equivalent in ISI marked make as approved by GE.

Material and labour for complete cleaning and checking the serviceability of fan coil unit of any capacity for having continuous sreviceability of FCU for any number of time as desired by Engr-in-Charge including replacement of minor spare part like Gasket, Teflon tape, flare nut, tightening of any loose glycol line connections, shifting FCU from one place to another place if required, heating up the freezed glycol line anywhere about the premices and cleaning with the chemical solution by pressure pump from inlet to outlet to have continuous flow of glycol fluid, repairing the insulation of pipe line of any size by providing shallow tape / GI wire as deemed fit, for fastening the insulation with pipe line, stopping any kind of leakage from any size of pipe line, tightening the loose electrical connections as related with FCU / Heating system, cleaning the air filter including radiator of FCU to the entire satisfaction of Engineer-in- Charge all as directed at site.

S&F in replacement of fan coil unit duel shaft electric motor 1/12 HP, 30 watt 930 RPM, 3 speed as per existing, complete all as specified and directed. Make- Maratan/CEG or equivalent in ISI marked make as approved by GE.

Welding the leakage portion of MS pipe line including earhwork complete and materials as required for welding the pipe line of size 25 mm to 200 mm including testing on full pressure complete all as specified and directed.

M&L for cleaning of MS overhead POL storage tank of capacity 2000 Ltr including all type of T&P and chemical required for the same, including welding work to leakage surface including opening and refixing the existing insulating materials to the external surface of storage tank.

M&L for Pressure gauge 100mm dia, rating 0 to 80 Kg/Sqcm including taking out existing unserviceable gauge complete all as specified and directed. Make :AE/IEBIG or equivalent in ISI marked make as approved by GE.

Material and labour for replacement of old unserviceable centrifugal monoblock pump KDI-515+ 3 phase 415 volts of capacity 5 HP with Mechanical seal complete fittings with accessories , complete all as specified and directed. Make : Kirloskar/Havells/Texmo

Material and labour for replacement of old unserviceable centrifugal monoblock pump 3 phase 415 volts of capacity 3 HP with Mechanical seal complete fittings with accessories , complete all as specified and directed. Make : Kirloskar/Havells/Texmo

T&P alongwith Labour only for attending of complaint for day to day / daily complaints by employed skilled staff, checking the serviceability of fan coil unit of any capacity for having continuous sreviceability of FCU for any number of time as desired by Engr-in-Charge including replacement of minor spare part like Gasket, Teflon tape, flare nut, tightening of any loose glycol line connections, shifting FCU from one place to another place if required, heating up the freezed glycol line anywhere about the premices to have continuous flow of glycol fluid, repairing the insulation of pipe line of any size by providing shallow tape / GI wire as deemed fit, for fastening the insulation with pipe line, stopping any kind of leakage from any size of pipe line, tightening the loose electrical connections as related with FCU / Heating system, cleaning the air filter including radiator of FCU to the entire satisfaction of Engineer-in- Charge all as directed at site. Note :-(i)Attending any complaints of different nature in a single day in Corps HQ COmplex Plant Room inside / outside will be considered as one job. ii)Any kind of replacement of major items shall be measured and paid for separately under respective item of schedule 'A' iii) . Any nature of complaint related with FCUs, radiators, bursting/cracking/leakage of MS pipe lines, replacement of valves etc will be completed round the clock by suitable trademen (welder with suitable T & P,(including portable heating materials)-01,Skilled mechanic of CHS-01, Plumber/Fitter with helper-each o1, Supervisor-01 as per descreation of Engineer-in- Charge.iv)Job slip will be maintained by the contractor Supervisor under supervision of concerned JE E/M CHS, suitable communication shall be maintained through JE incharge round the clock. v) Any delay in attending complaint will be directly reported to higher authorities and suitable penalities will be incured from the contractor (Rs1000/-Per job)

Dismantling of burner assembly at 41 Offrs CHS and removing of side cover of boiler capacity 4 lakh kilo/cal/hr and complete servicing the boiler including exhaust outlet i.e chimmney by removing the complete carbon/oil deposits with suitable coil shine chemical including repair to coil assembly by welding if there is any leakage found or any other repair required at site and reassembling/ testing the same, complete all as specified and directed.

All as per item no 35 but boiler capacity 3 lakh kilo/cal/hr complete all as specified and directed.

Dismantling of burner assembly at Pro unit(CMP) CHS and removing of side cover of boiler capacity 3 lakh kilo/cal/hr and complete servicing the boiler including exhaust outlet i.e chimmney by removing the complete carbon/oil deposits with suitable coil shine chemical including repair to coil assembly by welding if there is any leakage found or any other repair required at site and reassembling/ testing the same, complete all as specified and directed.

S&F in replacement of photo cell as per existing suitable for 3 to 4 lakh kilo Cal/hr burner rod assembly, complete all as specified and directed.

Material and labour for rewinding of electric motor 3 phase 415 volts of capacity 7.5 HP with superior quality super enameled copper winding wire of appropriate size and gauge as existing including varnishing , cotton tape, PVC sleeves etc, complete all as specified and directed.

Material and labour for rewinding of electric motor 3 phase 415 volts of capacity 5 HP with superior quality super enameled copper winding wire of appropriate size and gauge as existing including varnishing , cotton tape, PVC sleeves etc, complete all as specified and directed by Engr-in-Charge.

Material and labour for rewinding of electric motor 3 phase 415 volts of capacity 3 HP with superior quality super enameled copper winding wire of appropriate size and gauge as existing including varnishing , cotton tape, PVC sleeves etc, complete all as specified and directed by Engr-in-Charge.

Material and labour for rewinding of electric motor 3 phase 415 volts of capacity 2 HP with superior quality super enameled copper winding wire of appropriate size and gauge as existing including varnishing , cotton tape, PVC sleeves etc, complete all as specified and directed by Engr-in-Charge.

Material and labour for rewinding of electric motor 3 phase 415 volts of capacity 0.5 HP with superior quality super enameled copper winding wire of appropriate size and gauge as existing including varnishing , cotton tape, PVC sleeves etc, complete all as specified and directed by Engr-in-Charge.

S&F in replacement of High pressure fuel pipe 1.5 m as per existing, complete all as specified and directed.

S&F in replacement of plug top 05 Amps, 3 pin as per existing, complete all as specified and directed.

S&F in replacement of rotary type ON/OFF switches for Fan Coil unit 22mm dia as per existing, complete all as specified and directed.

S&F in replacement of contactor type MNX 12 (AC-15) : 4A, 415 V, 12 A for 5.5 KW with auxillury contactor MNX-A, A600.P600 complete all as specified and directed by Engr-in-Charge. Make : L&T

S&F in replacement of phase failure relay VSP D1 complete all as specified and directed by Engr-in-Charge. Make : Minilec or equivalent in ISI marked make as approved by GE

S&F in temp controller digital type Sz-7510P with sensor, complete all as specified and directed. Make- Subzero or equivalent in ISI marked make as approved by GE

S&F in replacement of over load relay 5A, 240 V AC/5A 28V, DC, 3A 150V, AC. Make - OMRON, LY4 (2873C), complete all as specified and directed.

S&F in replacement of over load relay 10A, 110 V AC, 1/2 HP, 20V AC, 10A 220V, AC. Make - OMRON, LY4 (2282H3), complete all as specified and directed.

S&F in replacement of over load relay 3A, 150V AC/5A 240V, AC, 5A 28V, DC. Make - OMRON, MY4, (2935C), complete all as specified and directed.

M&L for replacement of diesel filter as per existing (upto 1 ltrs) complete all as directed by Engr-in-Charge

S&F in replacement of burner nozzle suitable for 3 to 4 Lakh K Cal/Hr complete all as directed by Engr-in-Charge

S&F for sequence controller LOA 24 for burner rod assembly of 3 to 4 Lakh K Cal/Hour, complete all as specified and directed . Make- Siemens as per existing model.

S&F in replacement of Ignition Transformer electronic type suitable for 3 tp 4 Lakh K Cal/hr burner rod assembly, complete all as specified and directed. Make- Denforce or equivalent in ISI marked make as approved by GE

M & L for replacement of burner rod assembly single phase 220 volts, Make Bentone Type ST-120, Model-ST-120K, or Equavelent Eco flame Capacity 02-5.6KG/hr, suitable for 3 to 4 Lac Kcal/hr boiler complete all as specified and directed by Engr-in-Charge.

Supply, connection and testing of thermal heater wires on water supply pipe lines (GI/MS/PPR) for heating of water through minimum 25 Watt per meter in spiral/ straight line shape above outer diameter of pipe with aluminium tape insulation to preserve heat, fiber glass layer, second layer of aluminium tap to hold fiber glass by glass wool minimum 40mm thick with essential tapes complete. Make: HTC Chromalox or equivalent in ISI marked make as approved by GE

Supply and fixing and replacement of Chilled/Hot Water wall mounting indoor type Radiator Unit 600 /1.5TR (CFM/TR) Capacity as per existing size and incl 02 Nos of 20mm valve with stainer (inlet&outlet) incl heavy duty PVC pipe for connection complete all as specified and directed by Engr-In-Charge. Make : Carrier/Zeco or equivalent in ISI marked make as approved by GE

Supply and fixing in replacement of wall mounting (ECO Panel) Convector heater 2.5KW/Hrs Two heat output setup with auto control and LED temperature display. Diemension-Width 1200mm, height, 450mm depth 90mm with complete fixing accessories.