State Warehousing Corporation Tender

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 500 metres lead.

Dismantling steel work manually / by mechanical means in built up sections without dismembering and stacking within 500 metres lead as per directions of Engineer -in-Charge.

Dismantling roofing including ridges, hips, velleys and gutters etc., and stacking the material within 500 metres lead of :G.S. Sheet

Solid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete

Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 150 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs,landings, balconies and access platform including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more. All works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand). All works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

9 mm cement plastering of mix : 1:3 (1 cement : 3 fine sand ). All works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality Anjili wood /jack wood

Providing and fixing paneled and glazed shutters for doors, windows and clerestory windows, 35 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineerin - charge.using Anjili/ Jack wood

Providing and fixing paneled or paneled and glazed shutters for doors, windows and clerestory windows, 30 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding paneling which will be paid for separately, all complete as per direction 0f Engineer in- charge. using Anjili/ Jack wood

Providing and fixing paneling or paneling and glazing in paneled or paneled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured) paneling for paneled or paneled and glazed shutters 25 mm to 40 mm thick using good quality Anjili/ Jack wood

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured), Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick:Float glass panes4 mm thick glass pane

Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design. All works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.-Minimum thickness 2.0 mm) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. All works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Steel work using dismantled round tube including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc.All works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Providing and fixing Galvalume sheets ( Supply of Pre painted Alu- Zinc alloy coated steel sheets -55% Aluminium, 43% Zinc, 1.6% Silicons and not less than 0.5mm thick-PPGL). Sheet should be supplied in single length upto 12 metre or as desired by Engineer in charge.The sheet shall be fixed using self drilling screws with corrosion resistant (SDS of brand Patta) of size 5.5 x 55mm with EPDM seal at top of corrugation complete upto any pitch in horizontal/ vertical or curved surfaces,including providing necessary overlap not less than 200mm at end 1 1/2 corrugation at side excluding the cost of purlins, rafters and trusses and providing ridges including cutting to size and shape wherever required as per direction of engineer in charge, the ridge will be paid separately.The rate inclusive of covering of existing stocks inside godown from falling of dust and covering of roof from raining with tarpauline sheet during the execution of work also the cost and conveyance of material to site and necessary scaffoldings which required.The contractor shall submit the manufacturers test certificates of the roofing sheet before commencing the work and also required to conduct the test on the randomly selected sample from the site by the Engineer-in -Charge to ensure the minimum thickness.

Providing ridges or hips width 120 cm overall width plain Galvalume sheet of 0.50 mm thick.The sheet shall be fixed using self drilling/self tapping screws with EPDM seal, and bitumen washers complete.The rate inclusive of cost and conveyance of material to site and necessary scaffoldings which required.

Providing silicon compound covering to G.I. bolts over roof including cost of all materials, conveyance, labour charge, scaffolding etc complete as required.

Providing and fixing 200mm (or nearest greater available size) UPVC half split square type eave gutter including cost of all necessary fittings (PVC down pipe to be paid separately) and conveyance of all materials and labour charges, scaffolding etc complete. The rate also includes providing necessary support to the gutter by using MS Angles or straights.

Removing dry or oil bound distemper, water proofing cement paint and thelike by scrapping, sand papering and preparing the surface smooth includingnecessary repairs to scratches etc. All works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

Providing and fixing I st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer -in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of Ist quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 Coarse sand), including pointing the joints with white cement and matching pigments etc., complete.

Providing and fixing false ceiling with 9mm thick PVC plain panel board ceiling of approved quality at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of PVC board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as per drawings, specification and direction of the Engineer in Charge.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x400mm with single 15 mm C.P.brasspillar taps

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore

Supplying and fixing CP Health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

Providing and fixing floor trap of approved quality & make as per the direction of engineer in charge

Providing and fixing PTMT grating of approved quality and colour. Rectangular type with openable circular lid150 mm nominal size square 100 mm diameter of the inner hinged round grating

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2. All works including cost and conveyance of all materials,labour charges etc. complete as required.

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 25 mm pipe 10kgf /cm2. All works including cost and conveyance of all materials,labour charges etc. complete as required.

Providing and fixing PVC, pipes fittings including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 6 Kgf/cm2 - internal work- Exposed on wall. All works including cost and conveyance of all materials,labour charges etc. complete as required.

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 32 mm pipe 10Kgf/cm2. All works including cost and conveyance of all materials,labour charges etc. complete as required.

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 6 kgf/cm2. All works including cost and conveyance of all materials,labour charges etc. complete as required.

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work including cutting chases and making good the wall etc. 63 mm pipe 6 Kgf/cm2. All works including cost and conveyance of all materials,labour charges etc. complete as required.

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 75 mm pipe 6 Kgf/cm2. All works including cost and conveyance of all materials,labour charges etc. complete as required.

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Elbow including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -63 dia 45 degree Elbow including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -63x63x63 mm dia Door Tee including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Vent cowl including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x110x75 mm dia Door Tee including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

Providing and fixing PVC ball valve (ISI marked) of the approved brand for Rigid PVC pipes, including jointing with PVC solvent cement:br32 mm nominal bore including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

Providing and fixing PVC ball valve (ISI marked) of the approved brand for Rigid PVC pipes, including jointing with PVC solvent cement: 25mm nominal bore including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

Supplying and fixing Stainless steel soap dish including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

Supplying and fixing CP Towel rod 60cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

Supplying and fixing solid PVC door of size 0.80 x 2.10 M using door frame 50x47x5mm and 30mm thick solid PVC for the shutter in single leaf including 18 nos 50 mm scews fixed in walls including all door fittings cost and conveyance of all materials required etc. complete as per instruction. during execution

Painting

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface after preparing the surface by using wirebrush or emery paper,all works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work all works including cost and conveyance of all materials, labour charges, scaffolding etc. complete as required.

Applying priming coat:With ready mixed pink or Grey primer of approved and manufacture on wood work (hard and soft wood) all works including cost and conveyance of all materials, labour charges, scaffolding etc. complete as required.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work,all works including cost and conveyance of all materials, labour charges, scaffolding etc. complete as required.

Painting with synthetic enamel paint of approved brand and manufacture ofrequired colour to give an even shade :Two or more coats on old work painting over the existing structure after preparing the surface by using wirebrush or emery paper, all works including cost and conveyance of all materials, labour charges, scaffolding etc. complete as required.