University Of Agriculture And Horticulture Sciences Tender

Total

Excavation and refilling of pit of dimension 1.7mtr x 1.8mtr x 1.8mtr by using power tools, jack, hammer and earth mover. As per civil SR specification number KBS 2.1(a)/2.3.1

Providing and laying of CC bed of size 1 : 4 : 8 As per KBS 4.1,4.2(PWD DSR 2015-16 item no.4.3, Pg.No 06)

Providing and laying in position plain 1:2:4 CC nominal mix using 40mm and down size graded granite metal machine mixed concrete laid in layers not exceeding 15cm thick well compacted in foundation and plinth including cost of machinery, curing etc., 2×700 ×1600 KBS 4.1, 4.6 (PWD DSR 2015-16 item No 4.11 pg.No 07)

KSRB 4.9.1 Providing mild steel reinforcement of RCC work inclusing straightning, cutting, bending , hooping placing in position , lapping and/or welding wherever required, tying with biding wire and ancoring to the adjoingin members wherever neccesory complete as design ( lapps,hooks, and wastage shall not be measured and paid ) cost of materials, labour, HOM of machinary complete as per specification.

Supplying of 24mm dia x 750mm long foundation bolts made out of high tensile steel along with 4 nos nut and bolt washers, etc.,(MR)

150W flood street light:- Input Voltage: 100-300V AC, Universal electronic driver with internal surge protection of 4 KV (Applicability IS 15885, Driver Safely 16104-1/2) and power cut-off arrangement in case of phase-to-phase/440 V fault. AC Input Operating frequency range: 50 HZ ± 3%. Average rated life span of LEDs luminaries : More than 50,000 hrs., case temperature of 105°C with respect to lumen maintenance of 70%. Interchange ability:Suitable for pole mount. Total Harmonic Distortion for the complete fixture: 10% , Ambient Temperature: -10°C to +50°C, Working Temperature: -5°C to +60°C Working Humidity: 10% to 90% RH,Correlated Color Temperature(CCT):5700°K(ANSI-NEMA),Wattage-Design: One Watt minimum. Wattage-at operating current: One watt minimum. LED efficiency (Im/W) (at operating current (design) and Tj=85 deg C): More than 135 lumens/Watt. Luminaries Efficiency: A1/A2 Roads as per IS 1944: 180 watts More than 100 lumens/watt. Color Rendering Index of LEDs: 70, Power factor: More than 0.95. Driver Efficiency: 85%, LEDs shall be operated at a forward current : 70% of rated maximum forward current, in the range of 350 mA to 1000 mA. Surge suppresser: Internal voltage surge protection: Universal electronic driver with internal surge protection of 4 kv (Applicability IS 15885, driver safety 16104-1/2) External voltage surge protection: External surge protection device (SPD) with a minimum of 11KV/10ka shall be separately installed with each fixture. Finishing: Corrosion free High pressure aluminium die cast/extruded aluminium, grey/silver color corrosion resistant polyester powder coating. Heat Sink: Good thermal management system should be provided & LED must be mounted on high pressure die cast aluminium casing with suitable large surface area by Means of fins to dissipate the heat to ambient air. Corrosion resistant LT grey/silver Nano powder coating. Silicon gasket to ensure ingress protection against moisture & dust. Ingress Protection: Optical compartment IP-66 CPRI/NABL accredited lab test certificate shall be furnished at the time of inspection of materials works. Cover glass/Lens cover/Cover frame: Glass- Distortion free, clear, heat resistant, toughened UV stabilized glass. Lens cover- Lens should be of material resistant to degradation during service, due to atmospheric components, to avoid adverse impact on light output. Cover frame- Aluminum cover fixed to the housing by means of rust proof, 304 grade stainless steel screws. Lens module for LEDs: LED lights shall be provided with lenses/lens modules. Lens should be of material resistant to degradation during service, due to atmospheric components, to avoid adverse impact on light output. LEDs used in the luminary shall have : Min angle of 120 degree. Certification and test reports preferred/essential: CPRI/ERTL/ERDI/UL/NABL . Integrated circuit(IC): Industrial grade or above . Conform to Photo Biological Safely for the LEDs: As per 1EC62471. Luminary configuration/Technical requirement: Shall consist of two separate optical & control gear chambers. It should be easily replaceable by removing only the control gear chamber cover in the field condition whenever problem arises in the control gear without disturbing optical chamber. Manufacturer shall submit proof of procurement of LEDs & IES LM 80-08 / ISI 6105:2012 test reports of specific LED & IES LM 79-08 IS16106:2012 test reports from any of the Accredited laboratory : Proof of LED purchase invoice along with Test reports shall be submitted at the time of inspection of materials at the works. Impact Resistance: The luminary shall be built in such a way that it can withstand wind speed of 15 kmph.: CPRI/NABL accredited lab report supporting the same shall be furnished by the manufacturer at the time of inspection of materials at the works. Impact resistance IK08. Light uniformity ratio (Emin / Eavg): 0.4. Optical assembly : Structured LED array for optimized road way photometric distribution with photometric lenses designed to optimize application efficiency and minimize glare. Protection from over voltage : The luminaries shall be suitable for operation within the input supply voltage range specified. The driver of the light should be able to sense and cut-off power to the light in case of phase to phase / 440 V fault. BIS Mark :LED street light /road light and electronic driver shall standard BIS Mark and registration number as below. IS 10322 (Part-5/Sec 3): LED luminaries for Road and street lighting and IS10322 (Part 5/ Sec 5): LED Flood lights. Embossment : Lumina ire shall have company name/Logo Embossed on the housing. Stickering is not allowed , Warranty : 10 years as per DMA rates

wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper conductor single core wire in open or concealed system of wiring as per IS-694:1990 and confirming to GTP of GROUP-B 2.5sqmm PWD SR (2014-15) Page no 6 item no 2.6.3

Basic Rate

Add 3% Wt

Total

Fixing halogen/metal halide/SVL/IL/LED floodlight fitting over exising pole/wall ceiling including clamps, bolts, nuts and wiring using suitable capacity wires PWD SR (2014-15) Page no 108 item no 17.5

Basic Rate

Add 3% Wt

Total

Supplying and fixing angle iron frame work fabricated out of MS angle iron 50X50X6mm and MS flat with bolt washer etc., and painted with 2 coats of redoxide and then two coats of approved paint. PWD SR (2014-15) Page. No.49, Item. No. 6.39.2

Basic Rate

Add 3% Wt

Total

Fabricating Supplying and mounting MS box made out 16 SWG suitable for floor/wall mounting fully weather proof with provision for better heat dissipation, provided with hinged front cover, equipped with tamper proof locing arrangements, with suitable size clamps with necessary cable entry pipe with gland and box should be finished with 2 coats of red oxide primer paint and finally finished with approved colour enameled metal paint, etc complete., PWD SR (2014-15) Page. No. 49, Item.No 6.40.2

Basic Rate

Add 3% Wt

Total

Supplying & fixing miniature circuit breaker on existing MCB distributing boards using necessary fixing materials and ‘C’ type Curve, indicator ON/OFF, energy cross-3 with short circuit breaking capacity of 10 K and complete wiring as required confirming to IEC 60898 a) 5-32 Amps SP PWD SR (2014-15) Page No. 47, Item No 6.16.1

Basic Rate

Add 3% Wt

Total

Supplying of 1.1 KV LT UG cable having aluminum conductor PVC insulated, extruded inner sheathed, galvanized, steel strip (Except 2CX10 sqmm wire armoured) confirming to IS 3975;1990 (No of strips indicated in GTP) and extruded PVC outer sheated armoured cable with specified IS-1554 part-1;1988 and confirming to GTP of GROUP-A 4 core 10sqmm PWD SR (2014-15) P.No. 55, Item No 7.5.2

Basic Rate

Add 3% Wt

Total

Supplying & fixing of class A(medium duty) G1 Pipe of wall thickness not less than 3.25mm on Pole/Wall/Drain crossing with necessary clamping arrangement for UG cable of 1.1KV a) 40mm PWD SR (2014-15) Page. No. 62, Item No 7.12.1

Basic Rate

Add 3% Wt

Total

Supplying and fixing of porcelain fuse channel with cut out on existing wooden/panel using necessary nuts, bolts and washers. 32 Amps PWDSR(2014-15)Page.No.44,Item.No.6.7.2

Basic Rate

Add 3% Wt

Total

Supplying & fixing of 4 pole power contractor with NO/NC contacts on existing wood/panel board using necessary bolts, nuts, washers and wiring etc., complete with AC-3 Rating and as per IS -13947 40 Amps PWDSR(2014-15) Page.No.45, Item.No.6.12.2

Basic Rate

Add 3% Wt

Total

Supplying & fixing Microprocessor based Electronic timer (without contractor, Din Mounting using necessary bolts, nuts and washers etc.,). PWD SR (2014-15) Page.No. 51,I.No.6.45

Basic Rate

Add 3% Wt

Total

Digging of trench of 0.6m deep x 0.50 mtr wide refilling the trench to the required ground level and consolidating etc.,complete.( As per civil /SR. KSRB I-2 P-7) PWD SR (2014-15) Page No 61 Item No 7.9.1 and 7.9.4

A)In ordinary Soil

Basic Rate

Add 3% Wt

Total

B) CC cutting P.no.62 I.no. 7.9.5

Basic Rate

Add 3% Wt

Total

C ) Asphalt cutting P.no.62 I.no. 7.9.4

Basic Rate

Add 3% Wt

Total

Labour charges for laying of 1.1KV class UG cable in existing trench GI pipe/stone ware pipe/on pole as required. In existing trench/duct 6 Sqmm to 16 Sqmm PWD SR (2014-15) Page no 61 item no 7.8.1

Basic Rate

Add 3% Wt

Total

Supplying, fixing and wiring electronic 5 to 20 Amps single phase Class-1 Accuracy with Temper Proof Energy Meter. PWD SR (2014-15) Page no 48 item no 6.28

Basic Rate

Add 3% Wt

Total

Supplying, fixing, wiring, earth electrode for grounding conduits, I.C. cutout and other equipments on the meter board using 40 mm dia 2.90mm thick GI pipe 2.5 mtr long buried in a pit…The pit should be filled with equal proportion of salt and charcoal 150mm all-round the pipe to complete depth. The connection from the pipe to the conduit etc., is to be established through GI wire of size as per ISI specification 7.3.3. of IS 732 using 12mm dia bolts, nuts, washers and check nuts etc., the pipe shall have 16 through holes of 122mm dia. PWD SR (2014-15) Page. No. 55, Item .No.7.1

Basic Rate

Add 3% Wt

Total

KSRB 4-1.2: Providing and laying in position plain cement concrete of mix 1:3:6 with OPC cement @ 220 Kgs, with 40mm and down size granite metal coarse aggregates @.892 cum, machine mixed, concrete laid in layers not exceeding 15cms thick, well completed, in foundation including cost of all materials,labour,HOM of machinery curing conplete as per specifications. Specification No.KBS 4.1, 4.2

supply and fixing polished wood board made of not less than 15mm thick plank on both sides of not more than 2 pieces and fixing the same to the wall using tapered inverted wooden plugs screws etc,. Page No 44 item No 6.6.6 20"x20"x2.5"

Basic Rate

Add 2% Wtg

Total

Supplying heavy guage PVC conduit pipe 32mm dia 2.5mm thick confirming to IS 2509 with suitable size bends, juntion boxes adhesive paste etc.. A nd fixing using inverted hood plugs in case of RCC ceiling and RCC wall/ stone structure or rawl plugs in case of brick walls and cemement plastering the damaged portion using heavy guage saddles at an interval of 700mm using NF screws. PWD SR (2014-15) Page no 2 item no 1.1.3

Gescom deposit and other departmental charges & LS