Rural Development And Panchayat Raj Department Tender

code04 - Wet Mix Macadam (Plant mix method) Providing, laying, sCOMMONading and compacting graded stone aggregate to wet mix macadam specification including COMMONmixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver/grader in sub-base / base course on well COMMONpared surface and compacting with vibratory roller to achieve the desired density.406. A (COMMON SR 2023-24.Vol-3, SL.No.4.17, Pg.No.24)

code05 - Providing and constructing un-reinforced plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M20 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 m3 capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including construction joints, primer, sealant , curing of concrete slabs for 14days, and water finishing to lines and grade as per drawing and technical specification clause 1501 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work. (COMMON SR 2023-24, Vol-3 Sl.No. 16.27 ,P.No - 138)

code06 - Construction of Embankment by excavating the available approvedGravel/Murrum deposited at a place or borrow pits during or priorexcavation with all lifts and lead, transportation to site, spreading,grading to required slope and compacting to meet the requirementcomplete as per specifications, including cost of labour,rolling,water,all materials,usage& all other appurtenaces required to complete the work. (COMMON SR 2021-22,Vol-1,SI.No.1.8,P.No.7)

code07 - Earth work excavation by manual means for drains,canals, waste weir draft, approach channels, key trench, foundation of Bridges and such similar works in all kinds of soils , as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, excavated surface leveled and sides neatly dressed disposing off the excavated stuff or sorting & stackin selected stuff for reuse in a radius of 50 m an lift upto 1.5 m including cost of labour, tools & other appurtenaces required to complete the work

code08 - Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork shall be paid separately) Mix 1:3:6 (M10) Using 40 mm nominal size graded crushed coarse aggregates (COMMONSR 2023-24, Vol-1, Sl.No.2.1.3 ,P.No - 15)

code09 - Providing and laying in position Reinforced cement concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necesary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) MIX 1:2:4 (M15) Using 20 mm nominal size graded crushed coarse aggregates (COMMON SR 2023-24, Vol-1 Sl.No.2.4.1, P.No - 15)

code10 - Appendix I Additionalities for Formwork, Centering & Scaffolding Concrete Drain Works -35% (Comon SR Vol-1, S.N.2P.N. 115 vide corrizondum-3)

code11 - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification - Building. PWD SR 2023-24, V-1 I No.2.11(a) P-18 Rs:(89457.00+5%)/t

code12 - Construction of Embankment by excavating the available approvedGravel/Murrum deposited at a place or borrow pits during or priorexcavation with all lifts and lead, transportation to site, spreading,grading to required slope and compacting to meet the requirementcomplete as per specifications, including cost of labour,rolling,water,all materials,usage& all other appurtenaces required to complete the work. (COMMON SR 2021-22,Vol-1,SI.No.1.8,P.No.7)

code13 - HALUVAGALU CC ROAD;- Compacting Original Ground Compacting original ground supporting embankment Loosening, leveling and Compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150 mm, mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density as given in Table 300-2 for embankment construction.305.3.4 COMMON SR 2023-24, Vol-3, SL.No. 3.7, Pg.No.15

code14 - Construction of Granular Sub-Base by Mix in Place Method by providing well graded Gravel, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specifications. COMMON SR 2023-24, Vol-3, SL.No. 16.10, Pg.No.145

code15 - Wet Mix Macadam (Plant mix method) Providing, laying, sCOMMONading and compacting graded stone aggregate to wet mix macadam specification including COMMONmixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver/grader in sub-base / base course on well COMMONpared surface and compacting with vibratory roller to achieve the desired density.406. A (COMMON SR 2023-24.Vol-3, SL.No.4.17, Pg.No.24)

code16 - Providing and constructing un-reinforced plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M20 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 m3 capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including construction joints, primer, sealant , curing of concrete slabs for 14days, and water finishing to lines and grade as per drawing and technical specification clause 1501 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work. (COMMON SR 2023-24, Vol-3 Sl.No. 16.27 ,P.No - 138)

code17 - Earth work excavation by manual means for drains,canals, waste weir draft, approach channels, key trench, foundation of Bridges and such similar works in all kinds of soils , as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, excavated surface leveled and sides neatly dressed disposing off the excavated stuff or sorting & stackin selected stuff for reuse in a radius of 50 m an lift upto 1.5 m including cost of labour, tools & other appurtenaces required to complete the work

code18 - Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork shall be paid separately) Mix 1:3:6 (M10) Using 40 mm nominal size graded crushed coarse aggregates (COMMONSR 2023-24, Vol-1, Sl.No.2.1.3 ,P.No - 15)

code19 - Providing and laying in position Reinforced cement concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necesary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) MIX 1:2:4 (M15) Using 20 mm nominal size graded crushed coarse aggregates (COMMON SR 2023-24, Vol-1 Sl.No.2.4.1, P.No - 15)

code20 - Appendix I Additionalities for Formwork, Centering & Scaffolding Concrete Drain Works -35% (Comon SR Vol-1, S.N.2P.N. 115 vide corrizondum-3)

code21 - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification - Building. PWD SR 2023-24, V-1 I No.2.11(a) P-18 Rs:(89457.00+5%)/t

code22 - Construction of Embankment by excavating the available approvedGravel/Murrum deposited at a place or borrow pits during or priorexcavation with all lifts and lead, transportation to site, spreading,grading to required slope and compacting to meet the requirementcomplete as per specifications, including cost of labour,rolling,water,all materials,usage& all other appurtenaces required to complete the work. (COMMON SR 2021-22,Vol-1,SI.No.1.8,P.No.7)

code23 - ALAGILAWADA CC ROAD;- Compacting Original Ground Compacting original ground supporting embankment Loosening, leveling and Compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150 mm, mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density as given in Table 300-2 for embankment construction.305.3.4 COMMON SR 2023-24, Vol-3, SL.No. 3.7, Pg.No.15

code24 - Construction of Granular Sub-Base by Mix in Place Method by providing well graded Gravel, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specifications. COMMON SR 2023-24, Vol-3, SL.No. 16.10, Pg.No.145

code25 - Wet Mix Macadam (Plant mix method) Providing, laying, sCOMMONading and compacting graded stone aggregate to wet mix macadam specification including COMMONmixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver/grader in sub-base / base course on well COMMONpared surface and compacting with vibratory roller to achieve the desired density.406. A (COMMON SR 2023-24.Vol-3, SL.No.4.17, Pg.No.24)

code26 - Providing and constructing un-reinforced plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M20 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 m3 capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including construction joints, primer, sealant , curing of concrete slabs for 14days, and water finishing to lines and grade as per drawing and technical specification clause 1501 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work. (COMMON SR 2023-24, Vol-3 Sl.No. 16.27 ,P.No - 138)

code27 - Providing and fixing board displaying information, suc as 'Name of work, Tender cost, Name of Contractor, Workcompletion and liability period etc', having rectangular shape of 1.20m x 0.90m size made out 18 gauge (1.25mm) thick mild steel sheet painted with one coat of Zincchromate stoving primer and two coats of enamel paint on front side and grey stove enamel on back side and border / messages / symbols etc. with approved colour shade paint complete, on M.S.angleof size 35 x 35 x 3 mm frame with properly cross braced M.S. angles of size 35mmx35mmx3mm duly painted including Two M.S. angle iron posts of size 65 mm x 65 mm x 6 mm, 3.65 mlong painted with alternate black and white bands of 25 cm widthincluding all fixtures etc.and fixing the boards in 1:4:8 concrete block of size 60 cm x 60 cm x 75 cm including, excavationrefilling, transportation, and labour etc complete. Spec. No. As directed by Engineer in Charge & MoRTH specification 804