Rural Development And Panchayat Raj Department Tender

code04 - Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to completeheworkaspertechnical specifications. (The cost of steel reinforcement & formworkshall be paidseparately) Mix 1:4:8( M5) Using 40 mm nominal size graded crushed coarse aggregates & with all lead and lift. and as per direction of the Engineer in charge of work.

code05 - Providing and laying flooring with burnt stone slabs 10 cms thick, rough chistle dressed on sand bed 7.5 cms to 8 cms thick and pointed with cement mortar 1:3, , including cost of materials, sand, labour, curing complete as per specifications & with all lead and lift. and as per direction of the Engineer in charge of work.

code06 - 9.11 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ m2 including pointing the joints with white cement and matching pigments etc., complete.( & with all lead and lift. and as per direction of the Engineer in charge of work.

code07 - Providing skirting, dadooing, rises of steps with colour glazed tiles 6mm thick on 10mm thick cement plaster 1:3 and jointed with whitecement slurry over existing rough plaster surface using glazed tiles of approved make and size including cost of materials, labour, completeas per specifications & with all lead and lift. and as per direction of the Engineer in charge of work.

code08 - Providing and fixing in position fully panelled Matti/Nandi wood shutters for doors with , stiles and rails of 30mm. thick with bottom and lock rails 180mm wide top rail and stiles 100mm wide as per drawing and panels of 25mm thick including cost of materials, labour, usage charges complete as per specifications. (excluding cost of fixtures) & with all lead and lift. and as per direction of the Engineer in charge of work.

code09 - Providing and fixing in position fully panelled shutters for windows with Honne wood stiles and rails of 25mm. thick, 75mm wide in two halves with panels provided with MDF of 18mm thick including cost of materials, labour charges, usage charges complete as per specifications. (excluding cost of fixtures( & with all lead and lift. and as per direction of the Engineer in charge of work

code10 - Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 5.5 mm thick glass panes including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in- Charge & with all lead and lift. and as per direction of the Engineer in charge of work.

code11 - Providing & fixing factory made PVC Door frame of size 50x47mm witha wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet metered cut at corners & jointed 2 No.s of 150mm long brackets of 15x15mm M.S Square tube, the entire door frame to be reinforced with 19x19mm M.S Square tube of 19 gauge. The door frame to be fixed to the wall using M.S. Screws of 65/80mm size completeas per manufacturers specification & direction of Engineer-in-charge

code12 - Providing & fixing 30mm thick factory made rigid foam Panelled Door Shutters made from M.S. tube of 19 gauge thickness, size 19x19mm for stiles and 15x15mm for top & bottom rails, covered with heat moulded PVC C channel of 5mm thick sheet & 30 x 50mm wide to form stiles & 5mm thick & 75mm wide PVC Sheets for top rail, lock rail & bottom rail on either side & 5mm thick 20mm wide PVC sheet as gap insert for top rail & bottom rail, Panelling of 5mm thick PVC sheet fitted in the M.S. Frame, Sealed to the stiles & rails with 5x30mm PVC sheet beading on either side & joined together with solvent cement adhesive etc., Complete as per manufacturers specification & direction of Engineer-in-charge fixed to frames with 3 nos of 75 mm Aluminium hinges..: & with all lead and lift. and as per direction of the Engineer in charge of work.

code13 - Providing and fixing brass bib cock of approved quality :20 mm nominal bore. & with all lead and lift. and as per direction of the Engineer in charge of work.

code14 - Providing and fixing white vitreous china water closet squatting pan (Indian type)Long pattern WC pan of size 580mm & with all lead and lift. and as per direction of the Engineer in charge of work.

code15 - Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVCplain & brass threaded fittings This includes jointing of pipes & fittingswith one step CPVC solvent cement, trenching, refilling & testing of jointscomplete as per direction of Engineer in Charge. External work2 20 mm nominal dia Pipes(P-122 , IT-13.33.2) Common SR 23-24Volume 2

code16 - Providing and placing on terrace (at all floors levels)polyethylene water storage tank ISI:12701 marked with cover and suitable locking arrangements and making necessary holes for inlet outlet and over flow pipe but without fittings and the base support of tank & with all lead and lift. and as per direction of the Engineer in charge of work.

code17 - Providing and fixing MS inspection door of size 60 cms x 60 cms, includingMS frame made of 50x50x6mm angle, shutters made of 3mm thick MSsheets, with hinges, locking arrangements at top etc. including paintingwith anticorrosive approved paint etc. complete including all lead andlifts etc. & with all lead and lift. and as per direction of the Engineer in charge of work.

code18 - Providing, Single Phase Submersible Pump Sets of 100mm dia (4 inch) suitable for bore well confirming to IS 8034-2000 specifications, to worksite with testing of as per instructions of engineer incharge of work andlatest amendments0.50 HP( & with all lead and lift. and as per direction of the Engineer in charge of work.

code19 - Supplying PVC ringtite pipes conforming to IS 4985:2000 with latestamendments and conveying to worksite, rolling and lowering intotrenches, laying true to line and level and perfect linking at joints, testingand commissioning, including loading unloading at both destinations andcuts of pipes wherever ecessary including jointing of PVC pipes andspecials (excluding cost of specials) with jointing of approved type, withall labour with all lead & lift including encasing the pipe alround to a depthof not less than 15 cms. with soft gravel or selected earth available fromthe excavation etc. complete and giving necessary hydraulic test to therequired pressure as per ISS (Contractor will make his own arrangementsfor procuring water for testing) etc. for: 1.5 M010E PVC pipes 75mm dia., 6 kg/sqcm & class 3 & with all lead and lift. and as per direction of the Engineer in charge of work.

code20 - Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (Two coat applied @ 1.67 ltr/ 10 m²) on existing cement paint surface including preparing the surface after thoroughly cleaning the surface to remove all dirt, dust and foreign matter, cost of materials, labour complete as per specifications and as per directions of Engineer in-charge. I & with all lead and lift. and as per direction of the Engineer in charge of work.

code21 - Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One coats on old work as per specifications and as per directions of Engineer in charge. & with all lead and lift. and as per direction of the Engineer in charge of work.

code22 - Painting wood work with Deluxe Multi Surface Paint of requiredshade. Two coat applied @ 0.90 ltr/10 m² over an under coat of primer applied @0.75 ltr/10 m² of approved brand and manufacture to give an even shade including preparing the surface after thorougly cleaning oil, grease, dirt and foreign matter, sand papering and knotting , cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. & with all lead and lift. and as per direction of the Engineer in charge of work.

code23 - 4.17 406 Wet Mix Macadam (Plant Mix Method) Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver/grader in sub-base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.. & with all lead and lift. and as per direction of the Engineer in charge of work.

code24 - 16.27 1501 Providing and constructing un-reinforced plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M20 (Grade), coarse and fine aggregates conforming to IS:383:2016, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including construction joints, , primer, sealant , curing of concrete slabs for 14-days, and water finishing to lines and grade as per drawing and technical specification clause 1501 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work. & with all lead and lift. and as per direction of the Engineer in charge of work.

code25 - Supplying heavy guage P.V.C. conduit pipe 25 mm dia 2 mm thickconfirming to IS 2509 with suitable size bends iunction boxes, adhesive paste etc., and fixing using inverted wood plugs in case of RCC ceiling and RCC walls/stone structure or rawl plugs in case of brick walls and cement plastering damaged portion using heavy guage saddles at an interval of 700mm using N.F.Screws & with all lead and lift. and as per direction of the Engineer in charge of work.

code26 - Concelaed conduit System Supplying heavy gauge PVC Conduit pipe 19/20mm dia2mm thick confirming To IS 2509 with suitable size bends, metal/PVC junction boxes boxes adhesive paste etc., and running before concreting the slab. The conduit should be tied to the reinforcement rods by using binding wires and unused ways of junction boxes and pipe ends should be covered PVC end enclosers, run with 18SWG GI fish wire wherever neccesary 19/20mm dia 2mm thick & with all lead and lift. and as per direction of the Engineer in charge of work.

code27 - Supply and fixing PVC/ metal conduit deep junction box. 19/20mm Deep junction box & with all lead and lift. and as per direction of the Engineer in charge of work.

code28 - Supplying and flush mounting teak wood box without front plank, made of not less than 12mm thick wood, after due grove cutting, finishing with necessary cement plastering complete 10” x7” x3” (254x178x76mm) & with all lead and lift. and as per direction of the Engineer in charge of work.

code29 - Supplying and wiring adopting loop system in existing PVC conduit/casing capping, using 1100V grade, COPPER conductor flexible multistrand FRLS PVC insulated 2x1.5sq.mm cable conforming to the GTP with a 6Amphs flush type SP control switch shall be fixed on the existing plastic sheet/gang box. The other end of wires shall be terminated with sufficient loose length in a wood/PVC round block complete for each outlet.Long point above 3mtr up to 6mtr from tapping point to out let via switch & with all lead and lift. and as per direction of the Engineer in charge of work.

code30 - Supplying and wiring adopting loop system in existing PVC conduit/casing capping, using 1100V grade, COPPER conductor flexible multistrand FRLS PVC insulated 2x1.5sq.mm cable conforming to the GTP with a 6Amphs flush type SP control switch shall be fixed on the existing plastic sheet/gang box. The other end of wires shall be terminated with sufficient loose length in a wood/PVC round block complete for each outlet.Long point above Medium point above 3mtr up to 6mtr from tapping point to out let via switch & with all lead and lift. and as per direction of the Engineer in charge of work.

code31 - Supplying and wiring adopting loop system in existing PVC conduit/casing capping, using 1100V grade, COPPER conductor flexible multistrand FRLS PVC insulated 2x1.5sq.mm cable conforming to the GTP with a 6Amphs flush type SP control switch shall be fixed on the existing plastic sheet/gang box. The other end of wires shall be terminated with sufficient loose length in a wood/PVC round block complete for each outlet.Long point above 3mtr up to 6mtr from tapping point to out let via switch & with all lead and lift. and as per direction of the Engineer in charge of work.

code32 - Supplying and fixing regular M.C.B. distribution boards on wall/wood board/flush mounting using required clamps, bolts, nuts with provision for fixing suitable type capacity MCB’s single phase/3phase/single door with powder coated painting made out of 14SWGM.S enclosure & with all lead and lift. and as per direction of the Engineer in charge of work.

code33 - Wiring for lighting/ power circuit using one FRLS P.V.C.insulated 1100v.grade multistrand Copper with low conducror resistance single core wire in open or concealed system of wiring with specified IS 694 :1990 &confirming to the attached GTP of GROUP-A1.5 sq mm & with all lead and lift. and as per direction of the Engineer in charge of work.

code34 - Wiring for lighting/ power circuit using one FRLS P.V.C.insulated 1100v.grade multistrand Copper with low conducror resistance single core wire in open or concealed system of wiring with specified IS 694 :1990 &confirming to the attached GTP of GROUP-A2.5 sq mm & with all lead and lift. and as per direction of the Engineer in charge of work.

code35 - Wiring for lighting/ power circuit using one FRLS P.V.C.insulated 1100v.grade multistrand Copper with low conducror resistance single core wire in open or concealed system of wiring with specified IS 694 :1990 &confirming to the attached GTP of GROUP-A4 sq mm & with all lead and lift. and as per direction of the Engineer in charge of work.

code36 - Supplying 6A flush type socket and 6amps flush type SP switch either surface/flush mounting in existing gang box or in 4mm thick plastic sheet and fixing over a flush mounted wooden box wiring using necessary capacity wires as required as per IS 1293 and IS 3654 & with all lead and lift. and as per direction of the Engineer in charge of work.

code37 - Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 12936A 1way DP switch & with all lead and lift. and as per direction of the Engineer in charge of work.

code38 - Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293 Stepped Fan Regulator Two Module & with all lead and lift. and as per direction of the Engineer in charge of work.

code39 - Fixing all types and all capacities of fluorescent/false ceiling/ spot light/ CFL/ LED fittings indoor on the wall/ceiling rafter/girders using 23/0.0076” twin twisted pvc insulated wires, required no.s of round blocks& clamps (if require & with all lead and lift. and as per direction of the Engineer in charge of work.

code40 - Supplying capacitor type ceiling fan complete with down rod blades, shackle canopies for operation on 230 V 50 cycles single phase A/C supply conforming to ISS 374-1979 and with double ball bearing system 48” sweep (1200mm ) Regular modal & with all lead and lift. and as per direction of the Engineer in charge of work.

code41 - Supplying fixing wiring earth electrode for grounding conduits I.c.cutouts and other equipments on the meter board using 40mm dia 2.90mm thick GI pipe 2.5mtr long buried in a pit .The pit should be filled with equal proportion of salt and charcoal 150mm alround the pipe to complete depth. The connection from the pipe to the conduit etc,is to be established through GI wire of size asper ISI specification 7.3.3 of IS732 using12mm dia bolts,nuts, washers and checknuts etc the pipe shell have 16 through holes of 122mm dia & with all lead and lift. and as per direction of the Engineer in charge of work.