Rural Development And Panchayat Raj Department Tender

CSR_V3_pg n 17 I N 3.7 - Loosening, leveling and Compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150 mm, mixed with water at OMC andthen compacted by rolling so as to achieve minimum dry density as given in Table 300-2 for embankment construction

CSR_V1_pg n 7 I N 1.7 - Construction of Embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded with desired compaction. (Royalty shall be recovered @ Rs. 60.00/m3)

CSR_V1_pg n 7 I N 1.8 - Construction of Embankment by excavating the available approved Gravel/ Murrum deposited at a place or borrow pits during or prior excavation with all lifts and lead, transportation to site, spreading, grading to required slope and compacting to meet the requirement complete as per specifications, including cost of labour,rolling,water,all materials,usage& all other appurtenaces required to complete the work.

CSR_V3_pg n 153 I N 16.35 - Stabilized Sub-base / Base: With nano technology: Providing, Laying, Spreading and Compacting in-situ/borrow area soil of CBR 5% mixed with 30% 40mm downsize crushed Aggregate. Application: (1) Rip and loosen soil with excavator / tractor operated ripper and scarify with tractor operated rotavator to achieve desired thickness. Mix aggregates as per mix design with rotavator. (2) Spread OPC Cement 3% by weight of soil aggregate mix and mix with tractor operated rotavator. (3) Prepare and apply Chemical (IRC Accreditation)to achieve strength of minimum 4.5mpa mixed in OMC water (1000 ppm TDS) on loose mix . Scarify the treated mix with rotavator.(4).Compact the stabilized soil-aggregate-cement base with 8 to 10 tonne vibratory roller to achieve the desired density and thickness.Rates include all material, labour, hire charges of machinery etc. as per MoRD specifications, Tri-party agreement,IRC SP:89 2018 & direction of Engineer-in-Charge

CSR_V3_pg n 155 I N 16.39.2 - Providing and applying primer coat with bitumen emulsion (SS-2) on prepared surface of granular base including cleaning of surface and spraying primer at the rate of 1.0 kg/ m2 using mechanical means as per Technical Specification

CSR_V3_pg n 39 I N 5.19 - Providing, laying and rolling of Open-Graded Premix Carpet by Manual Means of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using VG-30 grade bitumen or Emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat as per Technical specification.

CSR_V3_pg n 44 I N 5.35 - Providing and laying Micro Surfacing Course Type II for traffic 1500CVPD with 6mm thickness as per IRC SP 81:2008 on existing structural sound & distressed pavement surface. (It is to be applied over an existing pavement surface which is structurally sound, but the surface is showing signs of premature ageing, aggregate loss, high degree of polishing, oxidation / hungry surface ) comprising of aggregates confirming to section 514 of MoRTH Specification. The Modified Bitumen Emulsion @ 10%, Filler cement @ 2%, Additive @ 0.5% and water as per requirement, aggregates as per Table 500-27. All these ingredients are mixed with required quantity of water to prepare semi fluid mass. The mix shall be spread mechanically using Microsurfacing Paver. The Cost includes cleaning of surface with Air compresser, laying and compacting to provide even riding surface and shall be rolling by Pneumatic Tyre Roller and ensure excessive movement does not occur, including cost of all materials, labour, usage charges of machinery, lead, lifts, loading, unloading, stacking, transporting, etc complete as per technical specification

CSR_V3_pg n 67 I N 8.16 ii - Reinforced cement concrete M15grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc

CSR_V3_pg n 67 I N 8.16 iii - Reinforced cement concrete M15grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc. 200 m stone (precast)

CSR_V3_pg n 78 I N 8.54 - Providing and fixing board displaying information, such as 'Name of work, Tender cost, Name of Contractor, Work completion and liability period etc', having rectangular shape of 1.20m x 0.90m size made out 18 gauge (1.25mm) thick mild steel sheet painted with one coat of Zinc chromate stoving primer and two coats of enamel paint on front side and grey stove enamel on back side and border / messages / symbols etc. with approved colour shade paint complete, on M.S.angle of size 35 x 35 x 3 mm frame with properly cross braced M.S. angles of size 35mmx35mmx3mm duly painted including Two M.S. angle iron posts of size 65 mm x 65 mm x 6 mm, 3.65 m long painted with alternate black and white bands of 25 cm width including all fixtures etc.and fixing the boards in 1:4:8 concrete block of size 60 cm x 60 cm x 75 cm including, excavation, refilling, transportation, and labour etc complete. Spec. No. As directed by Engineer in Charge & MoRTH specification 804