Directorate Of Municipal Administration Tender

code04 - Providing and laying vitrified floor tiles in 600x600mm sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ m2 including grouting the joints with white cement and matching pigments etc., complete..( Page no 62, item no 9.12.2,Buildings SR 2023-24 Volume-2 ).

code05 - Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per m2, including pointing in white cement mixed with pigment of matching shade complete. ( Page no 73, item no 10.14 ,Buildings SR 2023-24 Volume-2 ).

code06 - Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For Fixed Portion :Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) including cost of materials, labour, usage charges of machinery complete as per specifications. (Page no 87 . item no-11.35.1.3 Building S.R 2023-24 VOLUME -2)

code07 - Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in charge. (Glazing, paneling and dash fasteners to be paid for separately) :For shutters of doors, windows & ventilators including providing andfixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) including cost of materials, labour, usage charges of machinery complete as per specifications. (Page no 88 . item no-11.35.2.3 Building S.R 2023-24 VOLUME -2)

code08 - Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer- in-charge: Pre-laminated particle board with decorative lamination on both sides including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge(Page no 89 . item no-11.36.2Building S.R 2023-24 VOLUME -2)

code09 - Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 8 mm thickness (weight not less than 20 kg/ m²) including cost of materials, labour, usage charges of machinery complete as per specifications ( Page no89, item no 11.37.3 ,Building SR 2023-24 Volume-2 ).

code10 - Providing and laying vitrified floor tiles in 600x600mm sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ m2 including grouting the joints with white cement and matching pigments etc., complete..( Page no 62, item no 9.12.2,Buildings SR 2023-24 Volume-2 ).

code11 - Supplying PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joints, testing and commissioning, including loading unloading at both destinations and cuts of pipes wherever necessary including jointing of PVC pipes and specials (excluding cost of specials) with jointing of approved type, with all labour with all lead & lift including encasing the pipe alround to a depth of not less than 15 cms. with soft gravel or selected earth available from the excavation etc. complete and giving necessary hydraulic test to the required pressure as per ISS (Contractor will make his own arrangements for procuring water for testing) etc. for: PVC pipes 50mm dia., 6 kg/sqcm & class 3 (P No. 113 Sl No.10.1.3 W.S and UGD WORKS S.R2023-24 VOLUME -V).

code12 - Supplying PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joints, testing and commissioning, including loading unloading at both destinations and cuts of pipes wherever necessary including jointing of PVC pipes and specials (excluding cost of specials) with jointing of approved type, with all labour with all lead & lift including encasing the pipe alround to a depth of not less than 15 cms. with soft gravel or selected earth available from the excavation etc. complete and giving necessary hydraulic test to the required pressure as per ISS (Contractor will make his own arrangements for procuring water for testing) etc. for: PVC pipes 110mm dia., 6 kg/sqcm & class 3 (P No. 113 Sl No. 10.1.7 W.S and UGD WORKS S.R 2023-24 VOLUME -V).

code13 - Constructing brick masonry chamber of internal dimension 450x450mm and depth of 600mm (inner dimensions) with modular bricks of CD 75 in cement mortar 1:6, bed concrete 150mm thick with 1:3:6, plastering 12 mm thick with cement mortar 1:4, CC 1:2:4 coping 75mm thk for fixing CI cover & frame etc. excluding the cost of CI frame and cover..( Page no 187, item no 16.10 ,W.S and UGD WORKS S.R 2023-24 VOLUME -V).

code14 - Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required Size 600x450x200 mm ( Page no 134, item no 14.11-2 ,Buildings SR 2023-24 Volume-2 ).

code15 - Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc 15 mm nominal dia pipes(Page no122 . item no-13.32.1 Building S.R 2023-24 VOLUME -2)

code16 - Providing, fabricating and fixing partition frame work consisting of 50mm x 50mm sal wood frame work at spacing not exceeding 600mm clc fixed to the bottom and ceiling, the partition shall be skinned on both sides using 12mm thick commercial plywood of approved brand termite and water resistance, and top covered with 4mm thick approved quality veneer finished with melamine polish, complete including cost and conveyance of all materials, labour for all items of work, HOM as per specification.(Page No. 325 Item No.39.9 PW,P& IWTD Mangalore circle SR 2018-19 )

code17 - vinyl bonded water proof block board, shutters allround ward robe, lockable drawers with sliding channels, cupboard drapery hangers, curtain rods with end brackets, openable shutters with 19mm x 6mm thick plain teak wood beading, lipping 1.5mm thick commercial ply vertical support finished in approved 1mm lamination sheet of approved colour, shade and quality on all exposed surfaces. Inner surface painted with 2 coats of white synthetic enamel paint over 2 coats of Patti, one coat of wood primer, including cost of brass fittings, parliamentary hinges, C handles, tower bolts, magnetic catches, approved brand lock, adhesives, synthetic resins, nails, screws etc., complete including cost of all materials, labour charges, complete as per specification.e(Page No. 322 Item No.39.3 PW,P& IWTD Mangalore circle SR 2018-19 ) item not in CSR 2023-24

code18 - Meeting table- wooden Providing and fixing meeting table consisting of 25 mm thick PLPB table top edge bounded, 25 mm thick PLPB with edge bonded End table,18 mm thick PLPB with edge bonded Modesty, Hardware-Minifix assembly and screw leg., as per specifications, drawings and as directed by Engineer in charge1500 mm Dia X900 mm D X 750 mm Ht (6 seater) (P.No: 335 , Sl.No 39.21.1 ,PW,P& IWTD Mangalore Circle SR 2018-19 ). item not in CSR 2023-24

code19 - Storage Unit- Wooden -One side laminate Providing and fixing woode storage unit one side laminate with 18 mm PLY/PLPB with edge bound for body, 18mm PLY/PLPB with openable shutters and individual locking system for shutter, 9 mm PLY with edge bound for rear portion with Hafele fitting hinges, Hafele locks, Minifix assembly, screw legs, Handles and tower bolt complete as per specifications, drawings and as directed by Engineer in charge. PLY STORAGE - 900 mm W X 430 mm D X 2100 mm Ht (P No. 336 Sl No. 39.24.3 PW,P& IWTD Mangalore circle SR 2018-19 )item not in CSR 2023-24

code20 - Toughened glass 12 mm thickness with hole ( Page no A 41 item no 971 ,Buildings SR 2023-24 Volume-2 )

code21 - Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 600x600 mm ( Page no 62, item no 9.20.2 ,Building SR 2023-24 Volume-2 ).

code22 - Providing and fixing in position 12mm thick plaster of paris (Gypsum anhydrous) for ceiling reinforced with hessian cloth flat surface with ceiling tiles up to a height of 5 m above floor level over aluminium strips 25mm x 6mm and rendered smooth with plaster of paris including cost of materials, labour, curing complete as per specifications.( Page no 24, item no 7.31,Buildings SR 2023-24 Volume-2 ).

code23 - Providing and fixing Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge. .( Page no 83, item no 11.25.1,Buildings SR 2023-24 Volume-2 ).

code24 - Providing and placing on Terrace ( at allLevels) Polyethylene water Storage Tank IS 12701 marked , with cover and Suitable locking arrangement and making nessary holea for inlet , outlet and Overflow Pipes but without Fittings and the base Support for Tank ( Page no 125, item no 13.34 ,Buildings SR 2023-24 Volume-2 ).

code25 - Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete as per specifications and as per directions of Engineer in charge.( Page no 50, item no 8.51,Buildings SR 2023-24 Volume-2 ).

code26 - Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two coats) over and including water thinnable priming coat with cement primer after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge (Page no 45, item no 8.25,Buildings SR 2023-24 Volume-2 ).

code27 - Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two coats applied @ 1.43 ltr/10 m² over and including priming coat of exterior primer applied @ 2.20 kg/10 m²) with paint of approved quality to give an even shade, after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. ( Page no 46, item no 8.31,Buildings SR 2023-24 Volume-2 ).

code28 - Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two coats on new work after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. ( Page no 48, item no 8.40,,Buildings SR 2023-24 Volume-2 ).